CN 1700 Series Tech Spec Gea31546d English - 0 - 0 PDF
CN 1700 Series Tech Spec Gea31546d English - 0 - 0 PDF
CN 1700 Series Tech Spec Gea31546d English - 0 - 0 PDF
Rev.D - 08/2018
Consolidated*
1700 Series
Safety Valve
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 1
Scope of Design
Example
Flanged inlet safety valve, ASME Code Section I. 3. Verify pressure and temperature requirements on
Application. Set pressure 1000 psig, temperature 900°F, page 1700.33 for ASME Section I, ASME B16.34.
required relieving capacity 94,900 lbs./hr.= valve type
number 17???-2-S. At 1000 psig, 900°F and a #3 orifice, locate the D
1. Refer to capacity table on page 1700.45 for ASME temperature class and select the 900 class valve
Code Section I Saturated Steam. At 1000 psig set with 900# inlet flange and a 150# outlet flange =
pressure, select a #3 orifice with a saturated capacity valve type number 1736 D-2-S.
of 120,221 lbs./hr. = valve type number 173??-2-S. 4. Locate the valve type in the appropriate scope of
2. Correct for superheat using table on page 1700.66 design section page 3 and the configuration code on
for superheat correction factor at 3% overpressure. page 68. Complete the valve selection = valve type
At 1044.7 psia and 900°F, multiply saturated capacity number 1736D-2-S-I9-F1.
120,221 lbs./hr. by correction factor .797 = 95,923 5. Review the required weights, dimensions, materials
lbs./hr. and connections on page 9 and 20.
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 3
Scope of Design (Contd.)
Flanged Inlet – Type 17_7, class 1500
Inlet3&4 Outlet2 Orifice
Type Numbers
ANSI Std. R.F. ANSI Std. R.F.
Maximum Temperature1 Discharge Area
Flange Flange
Designation
750°F 1020°F 1060°F
Size Class Size Class in2 cm2
(399°C) (549°C) (571°C)
1-1/2" 1500 3" 150 1717B 1717D 1717E .994 6.413 1
2" 1500 3" 150 1727B 1727D 1727E 1.431 9.232 2
2-1/2" 1500 6" 150 1737B 1737D 1737E 2.545 16.420 3
3" 1500 6" 150 1757B 1757D 1757E 3.341 21.556 5
3" 1500 6" 150 1747B 1747D 1747E 3.976 25.653 4
4" 1500 6" 150 1767B 1767D 1767E 7.070 45.616 6
6" 1500 8" 150 1777QB 1777QD 1777QE 11.050 71.295 Q
6" 1500 10" 150 1787B 1787D 1787E 14.180 91.489 8
6" 1500 10" 150 1707RB 1707RD 1707RE 16.000 103.232 R
6" 1500 10" 150 1707RRB 1707RRD 1707RRE 19.29 124.459 RR
Notes:
1. To determine the maximum allowable pressure at a given temperature, refer to the appropriate pressure/temperature tables from page 32.
2. Available in an ANSI Class 300 outlet flange.
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 5
Scope of Design (Contd.)
Welded Inlet – Type 17_7W, class 1500
Outlet2 Orifice
Type Numbers
Inlet Buttweld ANSI Std. R.F.
Maximum Temperature1 Discharge Area
Flange
Designation
750°F 1020°F 1060°F
Size Class Size Class in2 cm2
(399°C) (549°C) (571°C)
1-1/2" 1500 3" 150 1717WB 1717WD 1717WE .994 6.413 1
2" 1500 3" 150 1727WB 1727WD 1727WE 1.431 9.232 2
2-1/2" 1500 6" 150 1737WB 1737WD 1737WE 2.545 16.420 3
3" 1500 6" 150 1757WB 1757WD 1757WE 3.341 21.556 5
3" 1500 6" 150 1747WB 1747WD 1747WE 3.976 25.653 4
4" 1500 6" 150 1767WB 1767WD 1767WE 7.070 45.616 6
6" 1500 8" 150 1777QWB 1777QWD 1777QWE 11.050 71.295 Q
6" 1500 10" 150 1787WB 1787WD 1787WE 14.180 91.489 8
6" 1500 10" 150 1707RWB 1707RWD 1707RWE 16.000 103.232 R
6" 1500 10" 150 1707RRWB 1707RRWD 1707RRWE 19.29 124.459 RR
Notes:
1. To determine the maximum allowable pressure at a given temperature, refer to the appropriate pressure/temperature tables from page 32.
2. Available in an ANSI Class 300 outlet flange.
Notes:
1. To determine the maximum allowable pressure at a given temperature, refer to the appropriate pressure/temperature tables from page 32.
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 7
Materials
17_5 Flanged
600 Pressure Class
Ref.
Part Material
No.
Temp. Classes to 750°F (399°C)
1 Base SA217 WC6 Alloy Steel 18
2 • Disc Holder Leaded Nickel Silver 21
3 • Guide Leaded Nickel Silver
4 • Upper Adjusting Ring Stainless Steel 16
5 Spring Alloy Steel
Temp. Classes to 1020°F (549°C) 15
1 Base SA217 WC6 Alloy Steel
2 • Disc Holder Monel
3 • Guide Monel
4 • Upper Adjusting Ring Stainless Steel
14
5 Spring Alloy Steel
Temp. Classes to 1060°F (571°C)
1 Base SA217 WC6 Alloy Steel
2 • Disc Holder Monel 5
3 • Guide Monel 11
4 • Upper Adjusting Ring Stainless Steel
5 Spring Alloy Steel 10 13
All Temp. Classes
6 Seat Bushing Stainless Steel 12 9
7 • Disc Inconel
8 • Lower Adjusting RIng Stainless Steel 3
4
9 Disc Collar Stainless Steel
10 Lift Stop Stainless Steel 19
11 • Overlap Collar Stainless Steel
20 2
12 Cover Plate Assembly
12A Cover Plate WC6 Alloy Steel 8
7
12B Floating Washer Monel
12C Washer Retainer Stainless Steel 6 1
13 Top Plate Assembly
13A Top Plate F11 Alloy Steel
13B Washer Retainer Stainless Steel
13C Floating Washer Monel
14 • Spindle Stainless Steel
15 Compression Screw Siicon Brass
16 Yoke SA216 WCC Carbon Steel
17 Yoke Rod (Not Shown) B16 Alloy Steel
18 Lifting Gear Iron or Steel
19 • Upper Adjusting Ring Pin Stainless Steel
20 • Lower Adjusting Ring Pin Stainless Steel
21 Compression Screw Locknut Siicon Brass
• = Recommended spare parts. See Maintenance Manual for quantity.
Note:
1. For F (1100°F/593°C) and G (1120°F/604°C) temperature class materials, contact
factory.
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 9
Materials (Contd.)
17_7 Flanged
1500 Pressure Class
Ref.
Part Material
No.
Temp. Classes to 750°F (399°C)
1 Base SA217 WC6 Alloy Steel
18
2 • Disc Holder Leaded Nickel Silver
3 • Guide Leaded Nickel Silver
16
4 • Upper Adjusting Ring Stainless Steel
5 Spring Alloy Steel
15
Temp. Classes to 1020°F (549°C)
22
1 Base SA217 WC6 Alloy Steel
2 • Disc Holder Monel
21 23
3 • Guide Monel
4 • Upper Adjusting Ring Stainless Steel
5 Spring Alloy Steel Valve Type Numbers
1787 & 1707R Only
Temp. Classes to 1060°F (571°C)
1 Base SA217 WC9 Alloy Steel
2 • Disc Holder Monel
3 • Guide Monel
4 • Upper Adjusting Ring Stainless Steel
5 Spring Alloy Steel 18
All Temp. Classes 24
6 Seat Bushing Stainless Steel
7 • Disc Inconel 16
8 • Lower Adjusting RIng Stainless Steel
15
9 Disc Collar Stainless Steel
10 Lift Stop Stainless Steel
11 • Overlap Collar Stainless Steel
12 Cover Plate Assembly
12A Cover Plate WC6 Alloy Steel 14
12B Floating Washer Monel
12C Washer Retainer Stainless Steel
13 Top Plate Assembly
5
13A Top Plate F11 Alloy Steel
11
13B Washer Retainer Stainless Steel
13C Floating Washer Monel
10 13
14 • Spindle Stainless Steel
15 Compression Screw Siicon Brass
16 Yoke SA216 WCC Carbon Steel
12 9
17 Yoke Rod (Not Shown) B16 Alloy Steel
3
18 Lifting Gear Iron or Steel 4
19 • Upper Adjusting Ring Pin Stainless Steel 19
20 • Lower Adjusting Ring Pin Stainless Steel
21 Thrust Bearing Steel 20 2
22 Compression Screw Adapter Stainless Steel
23 Thrust Bearing Cover Steel 7 8
24 Compression Screw Locknut Siicon Brass
• = Recommended spare parts. See Maintenance Manual for quantity. 6 1
Note:
1. For F (1100°F/593°C) and G (1120°F/604°C) temperature class materials, contact factory.
2. Locknut set screw supplied when valve set pressure is 2500 psig and above (Set screw
not shown).
Ref.
Part Material 24
No.
Temp. Classes to 750°F (399°C)
16
1 Base SA217 WC6 Alloy Steel
2 • Disc Holder Leaded Nickel Silver 15
3 • Guide Leaded Nickel Silver
4 • Upper Adjusting Ring Stainless Steel 22
5 Spring Alloy Steel
21 23
Temp. Classes to 1020°F (549°C)
1 Base SA217 WC6 Alloy Steel
2 • Disc Holder Monel
3 • Guide Monel
4 • Upper Adjusting Ring Stainless Steel
5 Spring Alloy Steel 18
Temp. Classes to 1060°F (571°C) 24
1 Base SA217 WC9 Alloy Steel
2 • Disc Holder Monel 16
3 • Guide Monel
4 • Upper Adjusting Ring Stainless Steel 15
5 Spring Alloy Steel
All Temp. Classes
6 Seat Bushing Stainless Steel
7 • Disc Inconel 14
8 • Lower Adjusting RIng Stainless Steel
9 Disc Collar Stainless Steel
10 Lift Stop Stainless Steel
11 • Overlap Collar Stainless Steel 5
12 Cover Plate Assembly 11
12A Cover Plate WC6 Alloy Steel
12B Floating Washer Monel 10 13
12C Washer Retainer Stainless Steel
13 Top Plate Assembly 12 9
13A Top Plate F11 Alloy Steel
3
13B Washer Retainer Stainless Steel
4
13C Floating Washer Monel
19
14 • Spindle Stainless Steel
15 Compression Screw Siicon Brass 2
20
16 Yoke SA216 WCC Carbon Steel
17 Yoke Rod (Not Shown) B16 Alloy Steel 7 8
18 Lifting Gear Iron or Steel
19 • Upper Adjusting Ring Pin Stainless Steel 6 1
20 • Lower Adjusting Ring Pin Stainless Steel
21 Thrust Bearing Steel
22 Compression Screw Adapter Stainless Steel
23 Spindle Button (1719 Only) Stainless Steel
24 Compression Screw Locknut Siicon Brass
23
• = Recommended spare parts. See Maintenance Manual for quantity.
Note:
1. For F (1100°F/593°C) and G (1120°F/604°C) temperature class materials, contact factory.
2. Locknut set screw supplied when valve set pressure is 2500 psig and above (Set screw
not shown).
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 11
Materials (Contd.)
17_5W Welded Inlet
600 Pressure Class
Ref.
Part Material
No.
Temp. Classes to 750°F (399°C)
1 Base SA216 WCC 18
1A Inlet Neck (1.5” through 3”) SA105 Carbon Steel 21
2 • Disc Holder Leaded Nickel Silver
3 • Guide Leaded Nickel Silver 16
4 • Upper Adjusting Ring Stainless Steel
5 Spring Alloy Steel 15
Temp. Classes to 1020°F (549°C)
1 Base SA217 WC6 Alloy Steel
1A Inlet Neck SA182 F11 Alloy Steel
2 • Disc Holder Monel
14
3 • Guide Monel
4 • Upper Adjusting Ring Stainless Steel
5 Spring Alloy Steel
Temp. Classes to 1060°F (571°C) 5
1 Base SA217 WC9 Alloy Steel 11
1A Inlet Neck SA182 F22 Alloy Steel
2 • Disc Holder Monel 10 13
3 • Guide Monel
4 • Upper Adjusting Ring Stainless Steel 12 9
5 Spring Alloy Steel
All Temp. Classes 3
4
6 Seat Bushing Stainless Steel
7 • Disc Inconel 19
2
8 • Lower Adjusting RIng Stainless Steel
9 Disc Collar Stainless Steel
20
8
10 Lift Stop Stainless Steel
7
11 • Overlap Collar Stainless Steel 1
12 Cover Plate Assembly 6
12A Cover Plate WC6 Alloy Steel 1A
12B Floating Washer Monel
12C Washer Retainer Stainless Steel
13 Top Plate Assembly
13A Top Plate F11 Alloy Steel
13B Washer Retainer Stainless Steel
13C Floating Washer Monel 6
14 • Spindle Stainless Steel
15 Compression Screw Siicon Brass
16 Yoke SA216 WCC Carbon Steel 1
17 Yoke Rod (Not Shown) B16 Alloy Steel
18 Lifting Gear Iron or Steel
19 • Upper Adjusting Ring Pin Stainless Steel
20 • Lower Adjusting Ring Pin Stainless Steel 4” Through 6”
Cast Inlet Neck
21 Compression Screw Siicon Brass
• = Recommended spare parts. See Maintenance Manual for quantity.
Note:
1. For F (1100°F/593°C) and G (1120°F/604°C) temperature class materials, contact factory.
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 13
Materials (Contd.)
17_7W Welded Inlet
1500 Pressure Class
Ref.
Part Material 18
No.
Temp. Classes to 750°F (399°C)
1 Base SA216 WCC
1A Inlet Neck (1.5” through 3”) SA105 Carbon Steel 24
2 • Disc Holder Leaded Nickel Silver
16
3 • Guide Leaded Nickel Silver
4 • Upper Adjusting Ring Stainless Steel
15
5 Spring Alloy Steel
Temp. Classes to 1020°F (549°C) 22
1 Base SA217 WC6 Alloy Steel
1A Inlet Neck SA182 F11 Alloy Steel 21 23
2 • Disc Holder Monel
3 • Guide Monel
4 • Upper Adjusting Ring Stainless Steel
5 Spring Alloy Steel
Temp. Classes to 1060°F (571°C)
1 Base SA217 WC9 Alloy Steel
1A Inlet Neck SA182 F22 Alloy Steel
2 • Disc Holder Monel
18
3 • Guide Monel
24
4 • Upper Adjusting Ring Stainless Steel
5 Spring Alloy Steel
16
All Temp. Classes
6 Seat Bushing Stainless Steel 15
7 • Disc Inconel
8 • Lower Adjusting RIng Stainless Steel
9 Disc Collar Stainless Steel
10 Lift Stop Stainless Steel
14
11 • Overlap Collar Stainless Steel
12 Cover Plate Assembly
12A Cover Plate WC6 Alloy Steel
12B Floating Washer Monel 11 5
12C Washer Retainer Stainless Steel
13 Top Plate Assembly
10
13A Top Plate F11 Alloy Steel
13
13B Washer Retainer Stainless Steel
12
13C Floating Washer Monel
14 • Spindle Stainless Steel 3 9
15 Compression Screw Siicon Brass
16 Yoke SA216 WCC Carbon Steel 19
17 Yoke Rod (Not Shown) B16 Alloy Steel 4
18 Lifting Gear Iron or Steel 20
19 • Upper Adjusting Ring Pin Stainless Steel
20 • Lower Adjusting Ring Pin Stainless Steel 7 2
21 Thrust Bearing Steel
22 Compression Screw Adapter Stainless Steel 6 8
23 Spindle Button (1719 Only) Stainless Steel
24 Compression Screw Siicon Brass 1A 1
• = Recommended spare parts. See Maintenance Manual for quantity.
Note:
1. For F (1100°F/593°C) and G (1120°F/604°C) temperature class materials, contact factory.
2. Locknut set screw supplied when valve set pressure is 2500 psig and above.
14 | BHGE © 2018 Baker Hughes, a GE company. All rights reserved.
Materials (Contd.)
17_9W Welded Inlet
18
2500 Pressure Class
Ref.
Part Material 24
No.
Temp. Classes to 750°F (399°C) 16
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 15
Materials (Contd.)
17_0W Welded Inlet
18
3000 Pressure Class
Ref.
Part Material 24 25
No.
16
Temp. Classes to 750°F (399°C)
1 Base SA216 WCC 15
1A Inlet Neck (1.5” through 3”) SA105 Carbon Steel
22
2 • Disc Holder Leaded Nickel Silver
3 • Guide Leaded Nickel Silver 21
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 17
Materials (Contd.)
Alternate Materials for Base Assembly
Consolidated safety valves are supplied to meet the specific material combination is often requested when rapid startup is expected on
requirements of our customers. The following special material the boiler, as is the case with peaking units. When heat is applied, the
requirements are available for the safety valves listed. Many boiler expansion rate is constant for both the inlet neck and seat bushing.
manufactures now prefer to match the safety valve inlet neck material Both the inlet neck and seat bushing are manufactured from high
to the material being used on the header and nozzle inlet. By matching strength forged material integrally welded to the cast valve body. A
the materials, welding procedures can be simplified and the overall Stellite deposit is added to the seating area.
cost of installation reduced.
Some customers prefer that the valve be supplied with the same
material for both the inlet neck and seat bushing. This material
Pressure
Valve Type
Class
1715W
1725W
600 1735W
1755W
1745W
1716W
1726W
900 1736W
1756W
1746W
Seat
1717W Bushing
1727W
1737W
1757W Inlet Neck
1747W
1500
1767W
1777QW
1787W Material Options
1707RW Ref.
No.
1707RRW Part Material
1719W
ASME ASME ASME ASME
1729W ASME
1 Base SA217 SA217 SA217 SA217
2500 1739W SA216 WCC
WC 6 WC 9 WC 9 C12A
1759W
ASME ASME ASME ASME
1749W ASME
2 Inlet Neck1 SA182 SA182 SA182 SA182
SA105
1710W F11 F22 F91 F91
1720W
ASME ASME ASME ASME
1730W ASME
3 Seat Bushing1&2 SA182 SA182 SA182 SA182
3000 SA105
1750W F11 F22 F91 F91
1740W
1760W 4 Hard Faced Stellite Stellite Stellite Stellite Stellite
1713W
1723W Note:
4500 1733W 1. Inlet neck and seat bushing can be supplied of one-piece construction on application.
2. Also available in ASME SA479 GR. 410 Material.
1753W
1743W
45° 45°
45° 45°
H
***
Anchor discharge
piping solidly to
building structure
D
Dismantling
Fabricated
Height (Max.)
steel drip pan
F
C
(Max.)
Vent (NPT)
(see caution)
Drain G
** Max. Dims
3" 150# – 7-1/4"
A
6" 150# – 12-1/2"
(± 1/6)
8" 150# – 16"
See Notes 1 & 2
**
B
(± 1/6)
Notes:
1. For lever clearance dimensions see page 31.
2. Appropriate considerations should be made for draining any condensate
which may accumulate in the cover plate vent piping, body bowl drain, and
drip pan elbow arrangement.
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 19
Dimensions & Weights (USCS) (Contd.)
Flanged Inlet – Type 17_5, class 600
All Temperature Classes Approx.
Vent
Size and Type A B C D E F G H Weight
in. in. in. in. in. in. in. in. NPT lbs.
1-1 ⁄2” - 1715 6 5-1 ⁄4 23-3⁄4 28 9 3-1 ⁄4 3-9⁄16 4-15⁄16 1 85
2” - 1725 7 5-1 ⁄2 28-1 ⁄2 34-1 ⁄2 10-1 ⁄4 3-3⁄8 4-5⁄8 5-15⁄16 1-1 ⁄4 100
2-1 ⁄2” - 1735 8-1 ⁄4 7 33-1 ⁄2 40-3⁄4 13 3-7⁄16 4-13⁄16 6-3⁄16 1-1 ⁄4 240
3” - 1755 8-1 ⁄2 7 37-1 ⁄4 44-3⁄4 15-1 ⁄2 3-15⁄16 5-1 ⁄2 5-15⁄16 1-1 ⁄2 285
3” - 1745 8-1 ⁄2 7 37-1 ⁄4 44-3⁄4 15-1 ⁄2 3-15⁄16 5-1 ⁄2 5-15⁄16 1-1 ⁄2 285
4” - 1765 9 8 40-3⁄4 49-1 ⁄4 15-1 ⁄2 5-13⁄16 6-7⁄8 6-7⁄16 2 475
4” - 1775Q 8-3⁄4 9 45-1 ⁄4 55-1 ⁄4 19 6 8-3⁄16 5-5⁄16 2 550
6” - 1775Q 12-11 ⁄16 9 49-1 ⁄4 59-1 ⁄4 19 6 8-3⁄16 9-1 ⁄4 2 600
6” - 1785 10-11 ⁄16 10 50-1 ⁄2 62-3⁄4 20-1 ⁄4 7-1 ⁄4 8-7⁄16 7-1 ⁄4 2-1 ⁄2 750
6” - 1705R 10-11 ⁄16 10 55-1 ⁄4 71-1 ⁄4 20-1 ⁄4 7-1 ⁄4 8-7⁄16 7-9⁄ 32 2-1 ⁄2 765
6” - 1705RR 10-11 ⁄16 10 55-1 ⁄4 71-1 ⁄4 20-1 ⁄4 7-1 ⁄4 8-7⁄16 7-9⁄ 32 2-1 ⁄2 765
45° 45°
45° 45°
J
***
Anchor discharge
piping solidly to
building structure
D
Fabricated Dismantling
steel drip pan Height (Max.)
G
C
Vent (NPT) (Max.)
(see caution)
H
Drain
** Max. Dims
3" 150# – 7-1/4"
6" 150# – 12-1/2" A
8" 150# – 16" (± 1/6)
See Notes 1 & 2
**
B
(± 1/6)
F
K
CAUTION
***The EVT-I and Hydroset
Steam flow will occur through the coverplate vent require 15” clearance.
when the valve is in the open position. Do not plug.
Pipe to safe location. The EVT-II requires 17” clearance.
And an additional 8” is required when
the assisted closing device is utilized.
Notes:
1. For lever clearance dimensions see page 31.
2. Appropriate considerations should be made for draining any condensate
which may accumulate in the cover plate vent piping, body bowl drain, and
drip pan elbow arrangement.
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 21
Dimensions & Weights (USCS) (Contd.)
Flanged Inlet – Type 17_5W, class 600
Temp. Temp. Temp.
All Temperature Classes Class to Class to Class to
750° 1020° 1060° Approx.
Vent
Size and Type Weight
A B C D E F G H J Max. Max. Max. NPT lbs.
in. in. in. in. in. in. in. in in. K in. 1 K in. 1 K in. 1
1-1 ⁄2” - 1715W 10 5-1 ⁄4 27-3⁄4 32 9 1-1 ⁄2 3-1 ⁄4 3-9⁄16 8-15⁄16 3.99 3.99 3.99 1 85
2” - 1725W 10 5-1 ⁄2 31-1 ⁄2 37-1 ⁄2 10-1 ⁄4 2 3-3⁄8 4-5⁄8 8-15⁄16 3.99 3.99 3.99 1-1 ⁄4 100
2-1 ⁄2” - 1735W 12 7 37-1 ⁄2 44-1 ⁄2 13 2-1 ⁄2 3-7⁄16 4-13⁄16 9-15⁄16 4.49 4.49 4.98 1-1 ⁄4 240
3” - 1755W 12 7 40-3⁄4 48-1 ⁄4 15-1 ⁄2 3 3-15⁄16 5-1 ⁄2 9-7⁄16 5.49 5.49 5.49 1-1 ⁄2 260
3” - 1745W 12 7 40-3⁄4 48-1 ⁄4 15-1 ⁄2 3 3-15⁄16 5-1 ⁄2 9-7⁄16 5.74 5.74 5.74 1-1 ⁄2 260
4” - 1765W 12 8 43-3⁄4 52-1 ⁄4 15-1 ⁄2 4 5-13⁄16 6-7⁄8 9-7⁄16 6.99 6.99 6.99 2 475
4” - 1775W 12 9 48-1 ⁄2 58-1 ⁄2 19 4-1 ⁄8 6 8-3⁄16 8-9⁄16 7.24 7.24 7.24 2 550
6” - 1775QW 12 9 48-1 ⁄2 58-1 ⁄2 19 6 6 8-3⁄16 8-9⁄16 8.74 8.74 8.74 2 600
6” - 1785W 12 10 51-3⁄4 64 20-1 ⁄4 6 7-1 ⁄4 8-7⁄16 8-9⁄16 8.74 8.74 8.74 2-1 ⁄2 750
6” - 1705RW 12 10 56-1 ⁄4 72-1 ⁄4 20-1 ⁄4 6 7-1 ⁄4 8-7⁄16 8-9⁄16 8.74 8.74 8.74 2-1 ⁄2 765
6” - 1705RRW 12 10 56-1 ⁄4 72-1 ⁄4 20-1 ⁄4 6 7-1 ⁄4 8-7⁄16 8-9⁄16 8.74 8.74 8.74 2-1 ⁄2 765
45° 45°
45° 45°
J
***
Anchor discharge
piping solidly to
building structure
D
Fabricated Dismantling
steel drip pan Height (Max.)
G
C
Vent (NPT) (Max.)
(see caution)
H
Drain
** Max. Dims
3" 150# – 7-1/4"
6" 150# – 12-1/2" A
8" 150# – 16" (± 1/6)
See Notes 1 & 2
**
B
(± 1/6)
F
K
CAUTION
***The EVT-I and Hydroset
Steam flow will occur through the coverplate vent require 15” clearance.
when the valve is in the open position. Do not plug.
Pipe to safe location. The EVT-II requires 17” clearance.
And an additional 8” is required when
the assisted closing device is utilized.
Notes:
1. For lever clearance dimensions see page 31.
2. Appropriate considerations should be made for draining any condensate
which may accumulate in the cover plate vent piping, body bowl drain, and
drip pan elbow arrangement.
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 23
Dimensions & Weights (USCS) (Contd.)
Welded Inlet – Type 17_9W, class 2500
Temp. Temp. Temp.
All Temperature Classes Class to Class to Class to
750° 1020° 1060° Approx.
Vent
Size and Type Weight
A B C D E F G H J Max. Max. Max. NPT lbs.
in. in. in. in. in. in. in. in in. K in. 1 K in. 1 K in. 1
1-1 ⁄2” - 1719W 10 6-1/2 31-1/2 37-1/4 10-3/4 1-1/2 3-1/4 3-13/16 8-7/16 3.99 3.99 4.49 1 190
2” - 1729W 10 6-1/2 34-3/4 42 10-3/4 2 3-3/8 4-1/8 8-7/16 4.99 4.99 5.49 1-1 ⁄4 200
2-1/2” - 1739W 12 7-1/2 41-1/2 50 15-1/2 2-1/2 3-7/16 5-7/16 9-7/16 5.99 5.99 5.99 1-1 ⁄4 400
3” - 1759W 12 7-1/2 45 55-1/4 16 3 3-15/16 5-1/2 9-7/16 6.49 6.49 6.99 1-1 ⁄2 470
3” - 1749W 12 7-1/2 46-3/4 59 16 3 3-15/16 5-1/2 9-7/16 6.49 6.49 7.24 1-1 ⁄2 470
1-1 ⁄2” - 1710W 10 6-1/2 31-1/2 37-1/4 10-3/4 1-1/2 3-1/4 3-13/16 8-7/16 4.49 4.49 4.99 1 190
2” - 1720W 10 6-1/2 34-3/4 42 10-3/4 2 3-3/8 4-1/8 8-7/16 4.99 4.99 5.49 1-1 ⁄4 200
2-1/2” - 1730W 10 7-1/2 43-1/2 54 15-1/2 2-1/2 3-7/16 5-7/16 9-7/16 5.99 5.99 6.49 1-1 ⁄4 400
3” - 1750W 12 7-1/2 47 59-1/4 16 3 3-15/16 5-1/2 9-7/16 6.49 6.49 7.24 1-1 ⁄2 480
3” - 1740W 12 7-1/2 47 59-1/4 16 3 3-15/16 5-1/2 9-7/16 6.74 6.74 7.49 1-1 ⁄2 480
4” - 1760W 12 9-11/16 65-1/8 76 22-3/4 4 5-13/16 8-1/8 8-3/16 10.49 10.49 10.49 2 1250
1-1 ⁄2” - 1713W 10 6-1/2 34-3/4 42 10-3/4 1-1/2 3-1/4 3-43/64 8-7/16 5.49 5.49 5.49 1-1 ⁄4 250
2” - 1723W 10 7-1/2 45-1/4 55-3/4 15-1/2 2 3-7/16 5-7/16 9-7/16 6.49 6.49 6.49 1-1 ⁄2 375
2-1/2” - 1733W 12 7-1/2 51-3/4 65-1/2 16 2-1/2 3-15/16 5-1/2 9-7/16 6.99 6.99 6.99 1-1 ⁄2 475
3” - 1753W 14 8 56-1/2 70-1/2 19-1/4 3 4-5/16 5-5/8 11-7/16 7.99 7.99 7.99 1-1 ⁄2 575
3” - 1743W 14 8 58 70-1/2 19-1/4 3 4-5/16 5-5/8 11-7/16 7.99 7.99 7.99 1-1 ⁄2 600
Note:
1. Maximum nominal “K” dimension based on standard inlet neck outside diameter. Oversize inlet necks also available (consult factory).
Butt weld configuration is dependent upon set pressure and customer’s required configuration.
45° 45°
45° 45°
H
***
Anchor discharge
piping solidly to
building structure
D
Dismantling
Fabricated
Height (Max.)
steel drip pan
F
C
(Max.)
Vent (NPT)
(see caution)
Drain G
** Max. Dims
3" 150# – 184.2mm
6" 150# – 317.5mm A
8" 150# – 406.4mm (± 1/6)
See Notes 1 & 2
**
B
(± 1/6)
CAUTION
***The EVT-I and Hydroset
Steam flow will occur through the coverplate vent require 15” clearance.
when the valve is in the open position. Do not plug.
Pipe to safe location. The EVT-II requires 17” clearance.
And an additional 8” is required when
the assisted closing device is utilized.
Notes:
1. For lever clearance dimensions see page 31.
2. Appropriate considerations should be made for draining any condensate
which may accumulate in the cover plate vent piping, body bowl drain, and
drip pan elbow arrangement.
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 25
Dimensions & Weights (Metric)
Flanged Inlet – Type 17_5, class 600
45° 45°
45° 45°
H
***
Anchor discharge
piping solidly to
building structure
D
Fabricated
Dismantling
steel drip pan
Height (Max.)
F
C
Vent (NPT) (Max.)
(see caution)
Drain
G
** Max. Dims
3" 150# – 184.2mm
6" 150# – 317.5mm A
** 8" 150# – 406.4mm (± 1/6)
See Notes 1 & 2
B
(± 1/6)
CAUTION
***The EVT-I and Hydroset
Steam flow will occur through the coverplate vent require 381mm clearance.
when the valve is in the open position. Do not plug.
Pipe to safe location. The EVT-II requires 432mm clearance.
And an additional 203mm is required when
the assisted closing device is utilized.
Notes:
1. For lever clearance dimensions see page 31.
2. Appropriate considerations should be made for draining any condensate
which may accumulate in the cover plate vent piping, body bowl drain, and
drip pan elbow arrangement.
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 27
Dimensions & Weights (Metric) (Contd.)
Flanged Inlet – Type 17_5W, class 600
Temp. Temp. Temp.
All Temperature Classes Class to Class to Class to Approx.
399° 549° 571° Vent
Size and Type Weight
A B C D E F G H J Max. Max. Max. NPT lbs.
mm mm mm mm mm mm mm mm mm K in. 1 K in. 1 K in. 1
1-1 ⁄2” - 1715W 254.0 133.4 704.9 812.8 228.6 38.1 82.6 90.5 227.0 3.99 3.99 3.99 1 38.6
2” - 1725W 254.0 139.7 800.1 952.5 260.4 50.8 85.7 117.5 227.0 3.99 3.99 3.99 1-1/4 45.4
2-1/2” - 1735W 304.8 177.8 946.2 1130.3 330.2 63.5 87.3 122.2 252.4 4.49 4.98 4.98 1-1/4 108.9
3” - 1755W 304.8 177.8 1035.1 1225.6 393.7 76.2 100.0 139.7 239.7 5.49 5.49 5.49 1-1/2 118.0
3” - 1745W 304.8 177.8 1035.1 1225.6 393.7 76.2 100.0 139.7 239.7 5.74 5.74 5.74 1-1/2 118.0
4” - 1765W 304.8 203.2 1111.3 1327.2 393.7 101.6 147.6 174.6 239.7 6.99 6.99 6.99 2 215.5
4” - 1775QW 304.8 228.6 1231.9 1485.9 482.6 104.8 152.4 208.0 217.5 7.24 7.24 7.24 2 249.5
6” - 1775QW 304.8 228.6 1231.9 1485.9 482.6 152.4 152.4 208.0 217.5 8.74 8.74 8.74 2 272.2
6” - 1785W 304.8 254.0 1314.5 1625.6 514.4 152.4 184.2 214.3 217.5 8.74 8.74 8.74 2-1/2 340.2
6” - 1705RW 304.8 254.0 1428.8 1835.2 514.4 152.4 184.2 214.3 217.5 8.74 8.74 8.74 2-1/2 347.0
6” - 1705RRW 304.8 254.0 1428.8 1835.2 514.4 152.4 184.2 214.3 217.5 8.74 8.74 8.74 2-1/2 347.0
Note:
1. Maximum nominal “K” dimension based on standard inlet neck outside diameter. Oversize inlet necks also available (consult factory).
Butt weld configuration is dependent upon set pressure and customer’s required configuration.
28 | BHGE © 2018 Baker Hughes, a GE company. All rights reserved.
Dimensions & Weights (Metric) (Contd.)
1/2-14 Drain Location
NPT Drain
45° 45°
45° 45°
H
***
Anchor discharge
piping solidly to
building structure
D
Fabricated
Dismantling
steel drip pan
Height (Max.)
G
C
Vent (NPT) (Max.)
(see caution)
Drain
H
** Max. Dims
3" 150# – 184.2mm
6" 150# – 317.5mm A
** 8" 150# – 406.4mm (± 1.6mm)
See Notes 1 & 2
B
(± 1.6mm)
CAUTION
***The EVT-I and Hydroset
Steam flow will occur through the coverplate vent require 381mm clearance.
when the valve is in the open position. Do not plug.
Pipe to safe location. The EVT-II requires 432mm clearance.
And an additional 203mm is required when
the assisted closing device is utilized.
Notes:
1. For lever clearance dimensions see page 31.
2. Appropriate considerations should be made for draining any condensate
which may accumulate in the cover plate vent piping, body bowl drain, and
drip pan elbow arrangement.
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 29
Dimensions & Weights (Metric) (Contd.)
Welded Inlet – Type 17_9W, class 2500
Temp. Temp. Temp.
All Temperature Classes Class to Class to Class to
Approx.
399°C 549°C Vent
571°C
Size and Type Weight
A B C D E F G H J Max. K Max. K Max. K NPT lbs.
mm mm mm mm mm mm mm mm mm in. 1 in. 1 in. 1
1-1 ⁄2” - 1719W 254.0 165.1 800.1 946.2 273.1 38.1 82.6 96.8 214.3 3.99 3.99 4.49 1 86.2
2” - 1729W 254.0 165.1 882.7 1066.8 273.1 50.8 85.7 104.8 214.3 4.99 4.99 5.49 1-1/4 90.7
2-1 ⁄2” - 1739W 304.8 190.5 1054.1 1270.0 393.7 63.5 87.3 138.1 239.7 5.99 5.99 5.99 1-1/2 181.4
3” - 1759W 304.8 190.5 1143.0 1403.4 406.4 76.2 100.0 139.7 239.7 6.49 6.49 6.99 1-1/2 213.2
3” - 1749W 304.8 190.5 1187.5 1498.6 406.4 76.2 100.0 139.7 239.7 6.49 6.49 7.24 1-1/2 213.2
Note:
1. Maximum nominal “K” dimension based on standard inlet neck outside diameter. Oversize inlet necks also available (consult factory).
Butt weld configuration is dependent upon set pressure and customer’s required configuration.
3” - 1745, 1746,
2” - 1723 18-1/8 3-1/16 5-5/8 8-5/16
1747,
1755, 1756, 1757
2-1/2” - 1730,
4” - 1765, 1766, 460.4 77.8 142.9 211.1
1739
1767
2-1/2” - 1733 3” - 1740, 1743 18-1/4 3-5/8 6-1/4 9-1/8 E
1749, 1750, 1753,
463.6 92.1 158.8 231.8
1759
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 31
Pressure/Temperature (USCS)
Set pressure limits (psig) for 1700 flanged & buttweld safety valves at designated
temperature (°F)
Meets ASME B&PVC Section I and ASME B16.34
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 33
Pressure/Temperature (USCS) (Contd.)
Set pressure limits (psig) for 1700 flanged & buttweld safety valves at designated temperature (°F)
Meets ASME B&PVC Section I and ASME B16.34
1500 Pressure Class
Temperature Class
B B B B D D D D D D E F G H J
Base Material Flanged
WC6 WC6 WC6 WC6 WC6 WC6 WC6 WC6 WC6 WC6 WC9 WC9 CF8M - -
Base Material Buttweld
WCC WCC WCC WCC WC6 WC6 WC6 WC6 WC6 WC6 WC9 WC9 CF8M WC9 WC9
Inlet Neck Material A105 A105 A105 A105 F11 F11 F11 F11 F11 F11 F22 F22 F316 F91 F92
Buttweld1
100-
Valve Inlet Outlet 650 700 750 800 850 900 950 1000 1020 1060 1100 1120 1200 1200
600
Type CL_1500 Flange2 °F °F °F °F °F °F °F °F °F °F °F °F °F °F
°F
Flange CL_150 3025 2940 2840 2660 2540 2435 2245 1595 1080 936 810 550 -
1717
ButtWeld CL_150 3100 3100 3100 3100 3100 3100 3100 3100 3100 2737 2367 1603 3100 2110
Flange CL_150 3025 2940 2840 2660 2540 2435 2245 1595 1080 936 810 550 1389
1727
ButtWeld CL_150 3100 3100 3100 3100 3100 3100 3100 3100 2540 2201 1903 1290 3100 1970
Flange CL_150 3025 2940 2840 2660 2540 2435 2245 1595 1080 936 810 550 1389
1737
ButtWeld CL_150 3100 3100 3100 3100 3100 3100 3100 3100 2156 1869 1861 1262 3100 1560
Flange CL_150 3025 2940 2840 2660 2540 2435 2245 1595 1080 936 810 550 1389
1757
ButtWeld CL_150 3100 3100 3100 3100 3100 3100 3100 2821 1912 1657 1845 1251 3100 1820
Flange CL_150 2000 2000 2000 2000 2000 2000 2000 1595 1080 936 810 550 1389
1747
ButtWeld CL_150 2000 2000 2000 2000 2000 2000 2000 2000 2000 1777 1845 1251 2000
Flange CL_150 1600 1600 1600 1600 1600 1600 1600 1595 1080 936 810 550 1389
1767
ButtWeld CL_150 1600 1600 1600 1600 1600 1600 1600 1600 1600 1576 1437 976 1600 1110 1750
Flange CL_150 1600 1600 1600 1600 1600 1600 1600 1595 1080 936 810 550 1389
1777Q
ButtWeld CL_150 1600 1600 1600 1600 1600 1600 1600 1600 1080 936 810 550 1545 800
1787 Flange CL_150 1600 1600 1600 1600 1600 1600 1600 1595 1200 1040 900 610 1389
ButtWeld CL_150 1600 1600 1600 1600 1600 1600 1600 1600 16003 16003 12003 9503 1545 930
Flange CL_150 1600 1600 1600 1600 1600 1600 1600 1595 1080 936 810 550 1389
1707R ButtWeld CL_150 1600 1600 1600 1600 1600 1600 1600 1600 1200 1040 900 610 1545 590 1600
16003 16003 11003 8503
Flange CL_150 1600 1600 1600 1600 1600 1600 1600 1595 1080 936 810 550 1389
1707RR ButtWeld CL_150 1600 1600 1600 1600 1600 1600 1600 1600 1200 1040 900 610 1545 500 1600
16003 16003 9253 7203
Notes:
1. Consult the factory. Set pressure limits for buttweld valves can be further limited by buttweld dimensions.
2. Available CL_300 with same Pressure/Temperature rating.
3. Meets ASME B&PVC Section I, Code Case 1876-2, but does not meet ANSI B16.34. (1996 Edition)
Temp Class B B B B D D D D D D E F G H J
Base Mtl Flanged WC6 WC6 WC6 WC6 WC6 WC6 WC6 WC6 WC6 WC6 WC9 WC9 CF8M - -
Base Mtl BW WCC WCC WCC WCC WC6 WC6 WC6 WC6 WC6 WC6 WC9 WC9 CF8M WC9 WC9
Inlet Neck Mtl BW1 A105 A105 A105 A105 F11 F11 F11 F11 F11 F11 F22 F22 F316 F91 F92
Temp Class B B B B D D D D D D E F G H J
Base Mtl Flanged WC6 WC6 WC6 WC6 WC6 WC6 WC6 WC6 WC6 WC6 WC9 WC9 CF8M - -
Base Mtl BW WCC WCC WCC WCC WC6 WC6 WC6 WC6 WC6 WC6 WC9 WC9 CF8M WC9 WC9
Inlet Neck Mtl BW1 A105 A105 A105 A105 F11 F11 F11 F11 F11 F11 F22 F22 F316 F91 F92
100-
Valve Inlet Outlet 650 700 750 800 850 900 950 1000 1020 1060 1100 1120 1200 1200
600
Type CL_3000 Flange2 °F °F °F °F °F °F °F °F °F °F °F °F °F °F
°F
ButtWeld CL_300 3100 3100 3100 3100 3100 3100 3100 3100 3100 2808 2429 1645 3100
1710
31002 31002 29002 2528
ButtWeld CL_300 3100 3100 3100 3100 3100 3100 3100 3100 2950 2557 2429 1645 3100
1720
31002 31002 31002 31002 2455 3100
ButtWeld CL_300 3100 3100 3100 3100 3100 3100 3100 3100 2812 2437 2414 1635 3100
1730
31002 31002 31002 31002 2540 3100
ButtWeld CL_300 3100 3100 3100 3100 3100 3100 3100 3100 2462 2134 2154 1460 3100
1750
31002 31002 31002 26502 2550
ButtWeld CL_300 3100 3100 3100 3100 3100 3100 3100 3100 2600 2253 2258 1529 3100
1740
31002 31002 31002 25252 2520
ButtWeld CL_300 3100 3100 3100 3100 3100 3100 3100 3100 3100 2808 2429 1645 3100
1760
31002 31002 31002 2477
Notes:
1. Consult the factory. Set pressure limits for buttweld valves can be further limited by buttweld dimensions.
2. Meets ASME B&PVC Section I, Code Case 1876-2, but does not meet ANSI B16.34. (1996 Edition)
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 35
Pressure/Temperature (USCS) (Contd.)
Set pressure limits (psig) for 1700 flanged & buttweld safety valves at designated temperature (°F)
Meets ASME B&PVC Section I and ASME B16.34
4500 Pressure Class
Temperature Class
B B B B D D D D D D E F G H J
Base Material Flanged
WC6 WC6 WC6 WC6 WC6 WC6 WC6 WC6 WC6 WC6 WC9 WC9 CF8M - -
Base Material Buttweld
WCC WCC WCC WCC WC6 WC6 WC6 WC6 WC6 WC6 WC9 WC9 CF8M WC9 WC9
Inlet Neck Material A105 A105 A105 A105 F11 F11 F11 F11 F11 F11 F22 F22 F316 F91 F92
Buttweld1
100-
Valve Inlet Outlet 650 700 750 800 850 900 950 1000 1020 1060 1100 1120 1200 1200
600
Type CL_4500 Flange2 °F °F °F °F °F °F °F °F °F °F °F °F °F °F
°F
ButtWeld CL_300 5360 5360 5360 5360 5020 5020 5020 4785 3240 2808 2429 1645 4165
1713
48302 48302 48302 47502 47502 47502 2528 5800
ButtWeld CL_300 5360 5360 5360 5360 5020 5020 5020 4785 3240 2808 2429 1645 4165
1723
48302 48302 48302 47502 47502 47502 2455 5800
ButtWeld CL_300 5360 5360 5360 5360 5020 5020 5020 4785 3240 2808 2429 1645 4165
1733
48302 48302 48302 47502 47502 47502 2547 5800
ButtWeld CL_300 5360 5360 5360 5360 5020 5020 5020 4785 3240 2808 2429 1645 4165
1753
48302 48302 48302 47502 47502 47502 2554 5800
ButtWeld CL_300 5360 5360 5360 5360 5020 5020 5020 4785 3240 2808 2429 1645 4165
1743
48302 48302 48302 47502 47502 47502 2333 5800
Notes:
1. Consult the factory. Set pressure limits for buttweld valves can be further limited by buttweld dimensions.
2. Meets ASME B&PVC Section I, Code Case 1876-2, but does not meet ANSI B16.34. (1996 Edition)
Notes:
1. Not recommended at this temperature. 5. ASME B31.1 - Appendix II analysis is limited to calculating valve outlet pressure
2. Consult the factory. and temperature. The calculated outlet pressure and temperature, using
3. Applies to 1-1/2” through 3” sizes only. ASME B31.1 Appendix II analysis, complies with ASME B16.34. The valve inlet
4. Consult the factory. Set pressure limits for buttweld valves can be further pressure/temperature rating is in compliance with ASME B16.34.
limited by buttweld dimensions.
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 37
Pressure/Temperature (USCS) Alternate (Contd.)
Set pressure limits (psig) for 1700 flanged & buttweld safety valves at designated temperature (°F)
Meets ASME B&PVC Section I ASME B16.34 and Non-Mandatory Code ASME B31.1-Appendix II. — (Note 5)
900 Pressure Class
Temperature Class
B B B B D D D D D D E F G
Base Material Flanged
WC6 WC6 WC6 WC6 WC6 WC6 WC6 WC6 WC6 WC6 WC9 WC9 CF8M
Base Material Buttweld
WCC WCC WCC WCC WC6 WC6 WC6 WC6 WC6 WC6 WC9 WC9 CF8M
Inlet Neck Material
A105 A105 A105 A105 F11 F11 F11 F11 F11 F11 F22 F22 F316
Buttweld3&4
Valve Inlet Outlet 100-
650°F 700°F 750°F 800°F 850°F 900°F 950°F 1000°F 1020°F 1060°F 1100°F 1120°F
Type CL_900 Flange 600°F
CL_150 1500 1500 1500 1477 1232 1048 806 645 477 414 280 (Note 1) (Note 2)
Flange
CL_300 1500 1500 1500 1500 1500 1460 1350 955 650 562 486 330 833
1716
CL_150 1500 1500 1500 1477 1232 1048 806 645 477 414 280 (Note 1) (Note 2)
ButtWeld
CL_300 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500
CL_150 1393 1183 1048 856 743 632 517 414 306 265 (Note 1) (Note 1) (Note 2)
Flange
CL_300 1500 1500 1500 1500 1500 1460 1350 955 650 562 486 330 833
1726
CL_150 1393 1183 1048 856 743 632 517 414 306 265 (Note 1) (Note 1) (Note 2)
ButtWeld
CL_300 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1290 1500
CL_150 1815 1765 1705 1595 1525 1460 1350 955 650 562 486 (Note 1) (Note 2)
Flange
CL_300 1815 1765 1705 1595 1525 1460 1350 955 650 562 486 330 833
1736
CL_150 3000 3000 3000 3000 2439 1921 1569 1232 839 714 503 (Note 1) (Note 2)
ButtWeld
CL_300 3000 3000 3000 3000 3000 3000 3000 2699 1830 1586 1615 1096 2773
CL_150 1815 1765 1705 1595 1525 1309 1069 790 583 506 350 (Note 1) (Note 2)
Flange
CL_300 1815 1765 1705 1595 1525 1460 1350 955 650 562 486 330 833
1756
CL_150 2274 2274 2274 1882 1569 1309 1069 790 583 506 350 (Note 1) (Note 2)
ButtWeld
CL_300 3000 3000 3000 3000 3000 3000 3000 2821 1912 1657 1431 972 2459
CL_150 1815 1765 1705 1477 1232 1048 806 632 477 414 286 (Note 1) (Note 2)
Flange
CL_300 1815 1765 1705 1595 1525 1460 1350 955 650 562 486 330 833
1746
CL_150 2000 2000 1736 1477 1232 1048 806 632 477 414 286 (Note 1) (Note 2)
ButtWeld
CL_300 2000 2000 2000 2000 2000 2000 2000 2000 2000 1777 1535 1042 2000
CL_150 1008 856 758 672 572 486 405 325 240 208 (Note 1) (Note 1) (Note 2)
Flange
CL_300 1500 1500 1500 1500 1500 1460 1350 955 650 562 486 330 833
1766
CL_150 1008 856 758 672 572 486 405 325 240 208 (Note 1) (Note 1) (Note 2)
ButtWeld
CL_300 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1361 924 1500
CL_150 1185 1027 874 743 658 549 458 366 271 235 (Note 1) (Note 1) (Note 2)
Flange
CL_300 1285 1285 1285 1285 1285 1285 1285 955 650 562 486 330 833
4” -1776Q
CL_150 1185 1027 874 743 658 549 458 366 271 235 (Note 1) (Note 1) (Note 2)
ButtWeld
CL_300 1285 1285 1285 1285 1285 1285 1285 1285 1285 1244 1075 730 1285
CL_150 1185 1027 874 743 658 549 458 366 271 235 (Note 1) (Note 1) (Note 2)
Flange
CL_300 1500 1500 1500 1500 1500 1460 1350 955 650 562 486 330 833
6” -1776Q
CL_150 1185 1027 874 743 658 549 458 366 271 235 (Note 1) (Note 1)
ButtWeld
CL_300 1500 1500 1500 1500 1500 1500 1500 1500 1207 1046 904 614 1500
CL_150 1040 1040 1040 1027 839 714 583 467 352 299 211 (Note 1) (Note 2)
Flange
CL_300 1040 1040 1040 1040 1040 1040 1040 955 650 562 486 330 1040
1786XHP
CL_150 1040 1040 1040 1027 839 714 583 467 352 299 211 (Note 1) (Note 2)
ButtWeld
CL_300 1040 1040 1040 1040 1040 1040 1040 1040 1040 1040 1025 611 1040
CL_150 1010 1010 1006 839 714 607 506 405 306 260 183 (Note 1) (Note 2)
Flange
CL_300 1010 1010 1010 1010 1010 1010 1010 955 650 562 486 330 1010
1706RXHP
CL_150 1010 1010 1006 839 714 607 506 405 306 260 183 (Note 1) (Note 2)
ButtWeld
CL_300 1010 1010 1010 1010 1010 1010 1010 1010 1010 1010 900 611 1010
CL_150 1010 1010 1006 839 714 607 506 405 306 260 183 (Note 1) (Note 2)
Flange
CL_300 1010 1010 1010 1010 1010 1010 1010 955 650 562 486 330 1010
1706RRXHP
CL_150 1010 1010 1006 839 714 607 506 405 306 260 183 (Note 1) (Note 2)
ButtWeld
CL_300 1010 1010 1010 1010 1010 1010 1010 1010 1010 1010 900 611 1010
Notes:
1. Not recommended at this temperature. 5. ASME B31.1 - Appendix II analysis is limited to calculating valve outlet
2. Consult the factory. pressure and temperature.
3. Applies to 1-1/2” through 3” sizes only. 6. The calculated outlet pressure and temperature, using ASME B31.1 Appendix
4. Consult the factory. Set pressure limits for buttweld valves can be further II analysis, complies with ASME B16.34. The valve inlet pressure/temperature
limited by buttweld dimensions. rating is in compliance with ASME B16.34.
Notes:
1. Not recommended at this temperature. 4. ASME B31.1 - Appendix II analysis is limited to calculating valve outlet
2. Consult the factory. pressure and temperature. The calculated outlet pressure and temperature,
3. Consult the factory. Set pressure limits for buttweld valves can be further using ASME B31.1 Appendix II analysis, complies with ASME B16.34. The valve
limited by buttweld dimensions. inlet pressure/temperature rating is in compliance with ASME B16.34.
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 39
Pressure/Temperature (USCS) Alternate (Contd.)
Set pressure limits (psig) for 1700 flanged & buttweld safety valves at designated temperature (°F)
Meets ASME B&PVC Section I ASME B16.34 and Non-Mandatory Code ASME B31.1-Appendix II. — (Note 4)
2500 Pressure Class
Temperature Class
B B B B D D D D D D E F G
Base Material Flanged
WC6 WC6 WC6 WC6 WC6 WC6 WC6 WC6 WC6 WC6 WC9 WC9 CF8M
Base Material Buttweld
WCC WCC WCC WCC WC6 WC6 WC6 WC6 WC6 WC6 WC9 WC9 CF8M
Inlet Neck Material
A105 A105 A105 A105 F11 F11 F11 F11 F11 F11 F22 F22 F316
Buttweld3&4
Inlet Outlet 100-
Valve Type 650°F 700°F 750°F 800°F 850°F 900°F 950°F 1000°F 1020°F 1060°F 1100°F 1120°F
CL_2500 Flange 600°F
Flange CL_300 3100 3100 3100 3100 3100 3100 3100 2655 1800 1560 1347 915 2315
1719
ButtWeld CL_300 3100 3100 3100 3100 3100 3100 3100 3100 1860 1574 1517 945 2525
Flange CL_300 3100 3100 3100 3100 3100 3100 3100 2655 1800 1560 1347 915 2315
1729
ButtWeld CL_300 3100 3100 3100 3100 3100 3100 3100 3100 2950 2557 2429 1645 3100
Flange CL_300 3100 3100 3100 3100 3100 3100 3100 2655 1800 1560 1347 915 2315
1739
ButtWeld CL_300 3100 3100 3100 3100 3100 3100 3100 3100 2600 2600 2230 1511 3100
Flange CL_300 3100 3100 3100 3100 3100 3100 3100 2655 1800 1560 1347 915 2315
1759
ButtWeld CL_300 3100 3100 3100 3100 3100 3100 3100 3100 2462 2134 2051 1390 3100
Flange CL_300 3100 3100 3100 3100 3100 3100 3100 2655 1800 1560 1347 915 2315
1749
ButtWeld CL_300 3100 3100 3100 3100 3100 3100 3100 3100 2462 2134 2154 1460 3100
Flange CL_300 2500 2500 2500 2500 2500 2500 2500 2500 1800 1560 1347 915 2315
1769
ButtWeld CL_300 - - - - - - - - - - - - -
Meets ASME B&PVC Section I ASME B16.34 and Non-Mandatory Code ASME B31.1-Appendix II. — (Note 4)
3000 Pressure Class
Temperature Class
B B B B D D D D D D E F G
Base Material Flanged
WC6 WC6 WC6 WC6 WC6 WC6 WC6 WC6 WC6 WC6 WC9 WC9 CF8M
Base Material Buttweld
WCC WCC WCC WCC WC6 WC6 WC6 WC6 WC6 WC6 WC9 WC9 CF8M
Inlet Neck Material
A105 A105 A105 A105 F11 F11 F11 F11 F11 F11 F22 F22 F316
Buttweld3&4
Inlet Outlet 100-
Valve Type 650°F 700°F 750°F 800°F 850°F 900°F 950°F 1000°F 1020°F 1060°F 1100°F 1120°F
CL_2500 Flange 600°F
1710 ButtWeld CL_300 3100 3100 3100 3100 3100 3100 3100 3100 3100 2808 2429 1645 3100
1720 ButtWeld CL_300 3100 3100 3100 3100 3100 3100 3100 3100 2950 2557 2429 1645 3100
1730 ButtWeld CL_300 3100 3100 3100 3100 3100 3100 3100 3100 2812 2437 2414 1635 3100
1750 ButtWeld CL_300 3100 3100 3100 3100 3100 3100 3100 3100 2462 2134 2154 1460 3100
1740 ButtWeld CL_300 3100 3100 3100 3100 3100 3100 3100 3100 2600 2253 2258 1529 3100
1770 ButtWeld CL_300 3100 3100 3100 3100 3100 3100 3100 3100 3100 2808 2429 1645 3100
Notes:
1. Not recommended at this temperature.
2. Consult the factory.
3. Consult the factory. Set pressure limits for buttweld valves can be further limited by buttweld dimensions.
4. ASME B31.1 - Appendix II analysis is limited to calculating valve outlet pressure and temperature. The calculated outlet pressure and temperature, using ASME B31.1
Appendix II analysis, complies with ASME B16.34. The valve inlet pressure/temperature rating is in compliance with ASME B16.34.
1713 ButtWeld CL_300 5360 5360 5360 5360 5360 5020 5020 4785 3240 2808 2429 1645 4165
1723 ButtWeld CL_300 5360 5360 5360 5360 5360 5020 5020 4785 3240 2808 2429 1645 4165
1733 ButtWeld CL_300 5360 5360 5360 5360 5360 5020 5020 4785 3240 2808 2429 1645 4165
1753 ButtWeld CL_300 5360 5360 5360 5360 5360 5020 5020 4785 3240 2808 2429 1645 4165
1743 ButtWeld CL_300 5360 5360 5360 5360 5360 5020 5020 4785 3240 2808 2429 1645 4165
Notes:
1. Consult the factory. Set pressure limits for buttweld valves can be further limited by buttweld dimensions.
2. ASME B31.1 - Appendix II analysis is limited to calculating valve outlet pressure and temperature. The calculated outlet pressure and temperature, using ASME B31.1
Appendix II analysis, complies with ASME B16.34.
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 41
Orifice Capacities
ASME, B & PVC, Section I rating - 2001 Edition
pounds per hour saturated steam at 3% overpressure, 90% of actual capacity
W=51.5KAP for “P” less than or equal to 1580 psia K=.878 (4” Q — K = .792)
W=51.5KAP x [.1906P-1000/.2292P-1061] for ”P” greater than 1580 psia A= flow area in sq. in.
P= (1.03 x set pressure) + 14.7
Apply correction factor for capacities on superheated steam. Correction factor tables begin on page 66. Review pressure temperature limits.
Pressure/temperature tables begin on page 32. The 1700 is certified as a restricted lift valve and capacities can be restricted down to 30% of its full rated capacity.
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 43
Orifice Capacities (Contd.)
ASME, B & PVC, Section I rating - 2001 Edition
pounds per hour saturated steam at 3% overpressure, 90% of actual capacity
W=51.5KAP for “P” less than or equal to 1580 psia K=.878 (4” Q — K = .792)
W=51.5KAP x [.1906P-1000/.2292P-1061] for ”P” greater than 1580 psia A= flow area in sq. in.
P= (1.03 x set pressure) + 14.7
Apply correction factor for capacities on superheated steam. Correction factor tables begin on page 66. Review pressure temperature limits. Pressure temperature tables
begin on page 32. The 1700 is certified as a restricted lift valve and capacities can be restricted down to 30% of its full rated capacity.
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 45
Orifice Capacities (Contd.)
ASME, B & PVC, Section I rating - 2001 Edition
pounds per hour saturated steam at 3% overpressure, 90% of actual capacity
W=51.5KAP for “P” less than or equal to 1580 psia K=.878 (4” Q — K = .792)
W=51.5KAP x [.1906P-1000/.2292P-1061] for ”P” greater than 1580 psia A= flow area in sq. in.
P= (1.03 x set pressure) + 14.7
Apply correction factor for capacities on superheated steam. Correction factor tables begin on page 66. Review pressure temperature limits. Pressure temperature tables
begin on page 32. The 1700 is certified as a restricted lift valve and capacities can be restricted down to 30% of its full rated capacity.
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 47
Orifice Capacities (Contd.)
ASME, B & PVC, Section I rating - 2001 Edition
pounds per hour saturated steam at 3% overpressure, 90% of actual capacity
W=51.5KAP for “P” less than or equal to 1580 psia K=.878 (4” Q — K = .792)
W=51.5KAP x [.1906P-1000/.2292P-1061] for ”P” greater than 1580 psia A= flow area in sq. in.
P= (1.03 x set pressure) + 14.7
Apply correction factor for capacities on superheated steam. Correction factor tables begin on page 66. Review pressure temperature limits. Pressure temperature tables
begin on page 32. The 1700 is certified as a restricted lift valve and capacities can be restricted down to 30% of its full rated capacity.
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 49
Orifice Capacities (Contd.)
ASME, B & PVC, Section I rating - 2001 Edition
pounds per hour saturated steam at 3% overpressure, 90% of actual capacity
W=51.5KAP for “P” less than or equal to 1580 psia K=.878 (4” Q — K = .792)
W=51.5KAP x [.1906P-1000/.2292P-1061] for ”P” greater than 1580 psia A= flow area in sq. in.
P= (1.03 x set pressure) + 14.7
Apply correction factor for capacities on superheated steam. Correction factor tables begin on page 66. Review pressure temperature limits. Pressure temperature tables
begin on page 32. The 1700 is certified as a restricted lift valve and capacities can be restricted down to 30% of its full rated capacity.
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 51
Orifice Capacities (Contd.)
ASME, B & PVC, Section I rating - 2001 Edition
pounds per hour saturated steam at 3% overpressure, 90% of actual capacity
W=51.5KAP for “P” less than or equal to 1580 psia K=.878 (4” Q — K = .792)
W=51.5KAP x [.1906P-1000/.2292P-1061] for ”P” greater than 1580 psia A= flow area in sq. in.
P= (1.03 x set pressure) + 14.7
Apply correction factor for capacities on superheated steam. Correction factor tables begin on page 66. Review pressure temperature limits. Pressure temperature tables
begin on page 32. The 1700 is certified as a restricted lift valve and capacities can be restricted down to 30% of its full rated capacity.
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 55
Orifice Capacities (Contd.)
ASME, B & PVC, Section VIII rating - 2001 Edition
pounds per hour saturated steam at 10% overpressure, 90% of actual capacity
W=51.5KAP for “P” less than or equal to 1580 psia K=.878 (4” Q — K = .792)
W=51.5KAP x [.1906P-1000/.2292P-1061] for ”P” greater than 1580 psia A= flow area in sq. in.
P= (1.10 x set pressure) + 14.7
Apply correction factor for capacities on superheated steam. Correction factor tables begin on page 66. Review pressure temperature limits. Pressure temperature tables
begin on page 32. The 1700 is certified as a restricted lift valve and capacities can be restricted down to 30% of its full rated capacity.
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 57
Orifice Capacities (Contd.)
ASME, B & PVC, Section VIII rating - 2001 Edition
pounds per hour saturated steam at 10% overpressure, 90% of actual capacity
W=51.5KAP for “P” less than or equal to 1580 psia K=.878 (4” Q — K = .792)
W=51.5KAP x [.1906P-1000/.2292P-1061] for ”P” greater than 1580 psia A= flow area in sq. in.
P= (1.10 x set pressure) + 14.7
Apply correction factor for capacities on superheated steam. Correction factor tables begin on page 66. Review pressure temperature limits. Pressure temperature tables
begin on page 32. The 1700 is certified as a restricted lift valve and capacities can be restricted down to 30% of its full rated capacity.
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 59
Orifice Capacities (Contd.)
ASME, B & PVC, Section VIII rating - 2001 Edition
pounds per hour saturated steam at 10% overpressure, 90% of actual capacity
W=51.5KAP for “P” less than or equal to 1580 psia K=.878 (4” Q — K = .792)
W=51.5KAP x [.1906P-1000/.2292P-1061] for ”P” greater than 1580 psia A= flow area in sq. in.
P= (1.10 x set pressure) + 14.7
Apply correction factor for capacities on superheated steam. Correction factor tables begin on page 66. Review pressure temperature limits. Pressure temperature tables
begin on page 32. The 1700 is certified as a restricted lift valve and capacities can be restricted down to 30% of its full rated capacity.
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 61
Orifice Capacities (Contd.)
ASME, B & PVC, Section VIII rating - 2001 Edition
pounds per hour saturated steam at 10% overpressure, 90% of actual capacity
W=51.5KAP for “P” less than or equal to 1580 psia K=.878 (4” Q — K = .792)
W=51.5KAP x [.1906P-1000/.2292P-1061] for ”P” greater than 1580 psia A= flow area in sq. in.
P= (1.10 x set pressure) + 14.7
Apply correction factor for capacities on superheated steam. Correction factor tables begin on page 66. Review pressure temperature limits. Pressure temperature tables
begin on page 32. The 1700 is certified as a restricted lift valve and capacities can be restricted down to 30% of its full rated capacity.
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 63
Orifice Capacities (Contd.)
ASME, B & PVC, Section VIII rating - 2001 Edition
pounds per hour saturated steam at 10% overpressure, 90% of actual capacity
W=51.5KAP for “P” less than or equal to 1580 psia K=.878 (4” Q — K = .792)
W=51.5KAP x [.1906P-1000/.2292P-1061] for ”P” greater than 1580 psia A= flow area in sq. in.
P= (1.10 x set pressure) + 14.7
Apply correction factor for capacities on superheated steam. Correction factor tables begin on page 66. Review pressure temperature limits. Pressure temperature tables
begin on page 32. The 1700 is certified as a restricted lift valve and capacities can be restricted down to 30% of its full rated capacity.
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 65
Orifice Capacities (Contd.)
Superheat Correction Factor
Notes:
1. For capacity on superheated steam, multiply saturated steam capacity by 2. Convert set pressure from (psig) to (psia) flowing pressure.
correction factor. 3. PSIA flowing = [set pressure psig x overpressure] + 14.7
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 67
Valve Configuration Code
1700 Series Main Valve
17 1 5 F B - 2 - S - X1 - I6 - F1 - HP - * - WSC - RL - CU - GR - LS
2 6 Q D X2 I9 F3 FL LD
3 7 R F X3 I15
5 9 RR G X4 I25
4 3 H X5
6 J X6
7 X7
8 X8
0 X9
Double Pole
LD
Double Throw
Base Semi-Finish
HE HG HH INLET -6
JE JG JH INLET -6
© 2018 Baker Hughes, a GE company. All rights reserved. Consolidated 1700 Series Safety Valve Technical Specifications | 69
DIRECT SALES OFFICE LOCATIONS
AUSTRALIA ITALY SOUTH AFRICA
Brisbane Phone: +39-081-7892-111 Phone: +27-11-452-1550
Phone: +61-7-3001-4319 Fax: +39-081-7892-208 Fax: +27-11-452-6542
Fax: +61-7-3001-4399
JAPAN SOUTH & CENTRAL
Perth Tokyo AMERICA AND THE CARIBBEAN
Phone: +61-8-6595-7018 Phone: +81-03-6871-9008 Phone: +55-12-2134-1201
Fax: +61-8-6595-7299 Fax: +81-03-6890-4620 Fax: +55-12-2134-1238
bhge.com
GEA31546D 07/2018