Technical Data Sheet

Approved 502;503 1,5 502 epoxy ^(ValidationDate) 1

Jotafloor Topcoat

Product description
This is a two component amide cured epoxy coating. It is a high performance product. It is easy to apply. This
product is tintable in a wide range of colours in Jotun's Multicolor Industry (MCI) system. It has good chemical,
abrasion and impact resistance. If enhanced slip resistance is required Jotafloor Non Slip can be used in the
system. To be used as topcoat in atmospheric environments. Suitable on approved primers on concrete
substrates.

Typical use
Designed for a wide range of floors with various levels of mechanical and chemical exposure. Specially designed
for floors where a dust free, hard wearing and aesthetically pleasing coating is required. Recommended for
Industrial walkways, Stair cases, light duty workshops, internal car park upstands, Plant rooms, back of house.
Other

Approvals and certificates

Determination of Bond strength to host concrete - BS 1881 : Part 207
Determination of Rapid Chloride Permeability - AASHTO T277
Determination of Water Permeability - DIN 1048
Determination of Acid or Alkali Reaction - ASTM D543
Determination of Impact Resistance - ISO 6272
Determination of Shore 'A' hardness - ASTM D2240
Determination of Taber Abrasion (1,000 Cycles) - ASTM D4060
Determination of Toxicity - BS 6920
Determination of Flame Spread - ASTM D1360
Additional certificates and approvals may be available on request.

Colours
selected range of colours tinted over Multicolor Industry tinting system (MCI)

Product data
Property Test/Standard Description

Solids by volume ISO 3233 50 ± 2 %

Gloss level (GU 60 °) ISO 2813 gloss (35-75)
Flash point ISO 3679 Method 1 25 °C
Density calculated 1.2 kg/l
VOC-US/Hong Kong US EPA method 24 (tested) 368 g/l
(CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)

The provided data is typical for factory produced products, subject to slight variation depending on colour.
All data is valid for mixed paint.
Gloss description: According to Jotun Performance Coatings' definition.

Date of issue: 4 February 2019 Page: 1/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Jotafloor Topcoat

Film thickness per coat

Typical recommended specification range

Dry film thickness 40 - 60 μm

Wet film thickness 80 - 120 μm
Theoretical spreading rate 12.5 - 8.3 m²/l

The actual spreading rate per coat may vary depending on the size of the Jotafloor Non Slip Aggregates used.

Surface preparation
To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any
contamination.

Surface preparation summary table

Surface preparation

Substrate Minimum Recommended

Concrete and Coated Clean, dry and undamaged compatible Clean, dry and undamaged compatible
surfaces coating as per SSPC SP13/NACE NO 6 coating as per SSPC SP13/NACE NO 6
/ASTM D4258 -05 /ACI 503.6R- /ASTM D4258 -05 /ACI 503.6R-
97/SSPC-TR 5/ICRI TECHNICAL 97/SSPC-TR 5/ICRI TECHNICAL
GUIDELINE 03741/NACE02203 GUIDELINE 03741/NACE02203

Laitance deposits are best removed by Planetary diamond disc grinder or by captive blasting followed by vacuum
cleaning to remove dust debris. For old concrete, Jotun technical team should visit the site and appropriate
surface preparation methodology should be recommended and that is to be followed.

Application
Application methods
The product can be applied by

Spray: Use airless spray.

Brush: Recommended for stripe coating and small areas. Care must be taken to achieve the
specified dry film thickness.
Roller: May be used. Care must be taken to achieve the specified dry film thickness.

Conditions during application :

The temperature of the substrate should be minimum 10 °C and at least 3 °C above the dew point of the air,
measured in the vicinity of the substrate. Good ventilation is usually required in confined areas to ensure proper
drying. The moisture content in the substrate should not exceed 4 % (by weight). The coating should not be
exposed to oil, chemicals or mechanical stress until fully cured.

Date of issue: 4 February 2019 Page: 2/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Jotafloor Topcoat

Product mixing ratio (by volume)

Jotafloor Topcoat Comp A 4 part(s)

Jotafloor Topcoat Comp B 1 part(s)

No part mixing of this product.

Use a slow speed drill and mixing paddle. Pour the full contents of the mixed material onto the floor immediately
after mixing is completed.
The temperature of base and curing agent is recommended to be 18 °C or higher when the paint is mixed.

Thinner/Cleaning solvent
Thinner: Jotun Thinner No. 17

Guiding data for airless spray

Nozzle tip (inch/1000): 17-23

Pressure at nozzle (minimum): 150 bar/2100 psi

Drying and Curing time

Substrate temperature 23 °C 40 °C

Surface (touch) dry 12 h 3h 1 h

Walk-on-dry 23 h 8h 3 h
Dry to over coat, minimum 23 h 7.5 h 3 h
Dried/cured for service 14 d 7d 3 d

For maximum overcoating intervals, refer to the Application Guide (AG) for this product.

Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal
tackiness.

Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks,
imprints or other physical damage.

Dry to over coat, minimum: The recommended shortest time before the next coat can be applied.

Dried/cured for service: Minimum time before the coating can be permanently exposed to the intended
environment/medium.

Induction time and Pot life

Paint temperature 23 °C

Induction time 10 min

Pot life 2h

Date of issue: 4 February 2019 Page: 3/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Jotafloor Topcoat

Product compatibility
Depending on the actual exposure of the coating system, various primers and topcoats can be used in
combination with this product. Some examples are shown below. Contact Jotun for specific system
recommendation.

Previous coat: Jotafloor Sealer or Jotafloor SF Primer or Jotafloor Solvent Free Primer

Packaging (typical)
Volume Size of containers
(litres) (litres)

Jotafloor Topcoat Comp A 4/16 5/20

Jotafloor Topcoat Comp B 1/4 1/5

The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary
due to local regulations.

Storage
The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well
ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle
with care.

Shelf life at 23 °C
Jotafloor Topcoat Comp A 24 month(s)
Jotafloor Topcoat Comp B 48 month(s)

In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf
life, thereafter the paint quality is subject to re-inspection.

Caution
This product is for professional use only. The applicators and operators shall be trained, experienced and have
the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical
documentation. Applicators and operators shall use appropriate personal protection equipment when using this
product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit
the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing
the work.

Health and safety

Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do
not inhale spray mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable
cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.

Colour variation

Date of issue: 4 February 2019 Page: 4/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Jotafloor Topcoat

When applicable, products primarily meant for use as primers or antifoulings may have slight colour variations
from batch to batch. Such products may fade and chalk when exposed to sunlight and weathering.

Disclaimer
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are often
used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product
itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves
the right to change the given data without further notice.

Users should always consult Jotun for specific guidance on the general suitability of this product for their needs
and specific application practices.

If there is any inconsistency between different language issues of this document, the English (United Kingdom)
version will prevail.

Date of issue: 4 February 2019 Page: 5/5

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com