it t Submittal

B1DS R2

Bell & Gossett

1DS Submersible
Dewatering Pump

FEATURES
■ Impeller: AISI 304 SS open impeller.
■ Diffuser Plate: AISI 304 SS with
Polyurethane coating for maximum
resistance to abrasion.
■ Casing: AISI 304 SS.
■ Mechanical Seal: Silicon carbide sealing
faces, all metal components of AISI type
300 stainless steel running in protected
oil chamber.
■ Elastomers: BUNA-N.
■ Shaft: AISI type 304 stainless steel high
strength pump shaft with keyed and
locking cap screw impeller fastening.
■ Motor: Air filled class F insulated design
for continuous use.
■ Designed for Continuous Operation:
Pump ratings are within the motor’s
working limits and can be operated con-
tinuously without damage.
■ Bearings: Upper and lower heavy duty
ball bearing construction.

Bell & Gossett is a brand of ITT

Residential and Commercial Water.

www.bellgossett.com

Engineered for life Bell &

it t
APPLICATIONS
Specifically designed for the following uses: Motor:
• Handling dirty waters • Single phase: 60 Hz, 3500 RPM, 1⁄2 HP, 115 and 230 V;
3
⁄4 and 1 HP, 230 V only.
• Draining ditches and pits
• Three phase: 60 Hz, 3500 RPM, 1⁄2 to 11⁄2 HP, 230 or
• Excavating in the building trades 460 V.
• Water transfer • Built-in thermal overload protection with automatic
• Industrial water drainage or transfer reset on single phase models.
• Three phase: Overload protection must be provided in
Specifications starter unit with three phase pumps.
Pump: • Power cord: 20 feet long. Single phase 115 V and
• Discharge size: 11⁄2" NPT. 230 V models are supplied with molded NEMA plugs
• Capacities: up to 110 GPM. and built-in capacitors. Three phase models are
supplied with bare leads.
• Total heads: up to 66 feet TDH.
• Class F insulation.
• Max. solids: 3⁄8" spherical.
• Mechanical seal: Silicon carbide rotary/silicon carbide
stationary, 300 series stainless steel metal parts,
BUNA-N elastomers.
• Maximum submergence: 23'.
• Temperature limit: 120ºF (50ºC) maximum.
• Fasteners: 300 series stainless steel.

Component Material
Model Information Pump body and
Stainless steel (AISI 304)
motor casing
Max. Weight
Order No. HP Volts Phase RPM
Amps. (lbs.) Outer sleeve Stainless steel (AISI 304)
1DS0511 115 10.3
1 29 Impeller Stainless steel (AISI 304)
1DS0512 4.5
1
⁄2 230
1DS0532 2.5 Motor shaft Stainless steel (AISI 304)
3 27
1DS0534 460 1.3 Suction strainer Stainless steel (AISI 304)
1DS0712 1 5.7 32
230 Stainless steel (AISI 304)
1DS0732 3
⁄4 3.6 Front diffuser plate coated with polyurethane
3 3450 29
1DS0734 460 1.8 elastomer
1DS1012 1 6.3 38 Lower mechanical seal Silicon carbide/silicon carbide
230
1DS1032 1 4.0
3 33 Upper lip seal Nitrile rubber
1DS1034 460 2.0
1DS1532 230 5.6 Stainless steel (AISI 304)
11⁄2 3 37 Handle
coated with polyacetalic resin
1DS1534 460 2.7


it t
mEtERS FEEt
70
SERIES: 1DS
1DS15
DISCHARGE: 11/"
0 SOLIDS: 3⁄8"
RPM: 3500
5 GPM
60
18
 FT

1DS10
16
50

14
1DS07
tOtal DYNamiC HEaD

1 40
1DS05

10
30

6 0

4
1 HP 1.5 HP
10
.5 HP .75 HP


0 0
0 0 40 60 80 100 u.S. GPm
0 5 10 15 0 5 m3/ hr
CaPaCitY


it t
dimensions
Dimensions
Series HP Phase in inches (mm) Discharge
11⁄2" NPT Size
H
1 141⁄8 (363)
1
⁄2
3 135⁄8 (348)
1 151⁄8 (383)
3
⁄4
1DS 3 141⁄8 (363) 11⁄2"
1 157⁄8 (403)
1
3 151⁄8 (383)
11⁄2 3 157⁄8 (403)
H

7" (178 mm)

2" (53 mm)

Typical Specifications
The contractor shall furnish and install quantity _____ , Model 1DS ________ Dewatering pump(s) as illustrated on
the plans and in accordance with the following specifications.
Single-phase models are available in: ½ HP/115 or 230V; ¾ and 1 HP/ 230V only. All single phase units are supplied
with 20' power cords with grounding plugs. They feature built-in capacitors and automatic reset, on-winding overload
protection.
Three phase units from ½ to 1½ HP are available in 230 or 460V, they require Class 10 overload protection in a starter
which is ordered separately. A 20' power cord with bare leads is supplied.
The air-filled, Class F insulated motors can be operated continuously without damage. Upper and lower heavy duty
ball bearings are provided. Maximum pump submergence is 23'.
Pumps shall be designed to pass 3/8" maximum spheres and are suitable for draining ditches and pits on construction
sites, water transfer and industrial water draining.
Materials of Construction: Pumps shall be constructed of stainless steel. Water intrusion shall be prevented by an outer
silicon carbide/silicon carbide/BUNA/SS mechanical seal and an upper Nitrile rubber lip seal.

Bell & Gossett

Bell & Gossett and the ITT Engineered Blocks Symbol are
registered trademarks and tradenames of ITT Corporation.
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

2881 East Bayard Street, Seneca Falls NY 13148

Phone 315-568-7123 • Fax 888-322-5877
© 2006 ITT Corporation

Engineered for life