Electromiografo Marca Xltec Modelo Neuromax 1004

XLTEK NEUROMAX
TECHNICAL MANUAL
Page 2
XLTEK NeuroMax
Publisher’s Notice
105352 Rev E
XLTEK NeuroMax Technical Manual
Natus Medical Incorporated

Excel-Tech Ltd. (XLTEK)
2568 Bristol Circle
Oakville, Ontario, L6H 5S1 Canada
Tel: 905-829-5300 or Fax:
Free (US & Canada):
Technical Support Email:
Customer Service Email:
EUROPEAN AUTHORIZED REPRESENTATIVE:

Natus Europe GmbH
Robert-Koch-Str. 1
82152 Planegg
Germany
Copyright © 2012 by Excel-Tech Ltd. (XLTEK)
The information in this publication is provided for reference only. All information contained in this publication is believed to
be correct and complete. Excel-Tech Ltd. shall not be liable for errors contained herein nor for incidental or consequential
damages in connection with the furnishing, performance, or use of this material. All product specifications, as well as the
information contained in this publication, are subject to change without notice.
This publication may contain or reference information and products protected by copyrights or patents and does not
convey any license under the patent rights of Excel-Tech Ltd., nor the rights of others. Excel-Tech Ltd. does not assume
any liability arising out of any infringements of patents or other rights of third parties.
All rights reserved. This document contains confidential or proprietary information of Excel-Tech Ltd. No part of this
document may be reproduced or transmitted in any form or by any means without the written permission of Excel-Tech
Ltd.
Excel-Tech Ltd. makes no warranty of any kind with regard to this material, including but not limited to the implied
warranties of merchantability and fitness of a particular purpose.
Page 1
XLTEK NeuroMax
TABLE OF CONTENTS
NEUROMAX SAFETY AND STANDARDS CONFORMITY 6
1. WELCOME TO THE NEUROMAX 12
1.1. INTRODUCTION 13
1.1.1. INTENDED USE 13
1.2. CUSTOMER SERVICE 13
1.3. USING THE MANUAL 14
2. THE XLTEK NEUROMAX 15
2.1. OPERATING CONDITIONS 15

2.1.1. ENVIRONMENT PARAMETERS 15
2.1.2. TRANSPORT AND STORAGE PARAMETERS 15
2.2. SPECIFICATIONS 16
MATERIALS 16
EXTERNAL CONNECTORS 16
CHANNELS 16
SAMPLING RATE 16
SIZE AND TYPE 16
RESOLUTION 16
CMRR 16
NOISE 16
MAXIMUM SIMULATOR VOLTAGE 17
MAXIMUM STIMULATOR CURRENT 17
STIMULATOR CURRENT ACCURACY 17
STIMULATOR DURATION ACCURACY 17
VOLTAGE ACCURACY ON SCREEN 17
2.3. WARNINGS AND CAUTIONS 17
2.3.1. W ARNINGS 18
2.3.2. CAUTIONS 20
2.4. EXPLANATION OF LABELING SYMBOLS 22
2.5. MAIN MENU 23
2.6. KEY PAD 24
2.7. HOT KEYS 27
2.7.1. SENSORY NERVE CONDUCTION HOT KEYS 27
2.7.2. ELECTROMYOGRAPHY HOT KEYS 27
2.7.3. EVOKED POTENTIAL HOT KEYS 28
2.8. CREATING A PATIENT FILE 29
2.9. GENERATING TEST REPORTS 30
2.9.1. REPORT FUNCTIONS 30
3. NERVE CONDUCTION TESTS 33
3.1. MOTOR AND SENSORY NERVE CONDUCTIONS 34
Page 2
XLTEK NeuroMax
3.1.1. SETTING UP A NERVE CONDUCTION STUDY 34

3.1.2. CONDUCTING AN NCS 36
3.1.3. ABOUT THE REP STIM TEST 37
3.1.4. PERFORMING A REP STIM TEST 38
3.1.5. ABOUT THE F-W AVE TEST 40
3.1.6. PERFORMING AN F-W AVE TEST 41
3.1.7. SETTING UP AN H-REFLEX TEST 44
3.1.8. ACQUIRING H-REFLEX RESPONSES 44
4. EMG TESTS 45
4.1. SETTING UP THE EMG TEST MENU 45

4.1.1. SETTING UP AN EMG 45
4.1.2. ACQUIRING AN EMG 46
4.2. FREE RUN EMG FEATURES 48
4.2.1. REVIEWING FREE RUN EMG 48
4.2.2. ANALYZING TURNS AND AMPLITUDE 48
4.3. TRIGGERED EMG FEATURES 49
4.3.1. ACTIVATING TRIGGERS 49
4.3.2. SAVING A TEST 50
4.3.3. ANALYZING AND REVIEWING MOTOR UNITS 50
5. OTHER TESTS 50
5.1. OTHER TESTS 50

5.1.1. SETTING UP EVOKED POTENTIALS (EP) 51
5.1.2. CONDUCTING EVOKED POTENTIALS 51
5.1.3. SEP TESTS 53
5.1.4. SUGGESTED SEP PROTOCOLS 54
5.1.5. DERMATOMAL SEPS 56
5.2. BLINK REFLEX 57
5.2.1. SETTING UP A BLINK REFLEX TEST 57
5.2.2. CONDUCTING BLINK REFLEX TESTS 57
5.3. INCREMENTAL STIMULATION 58
5.3.1. SETTING UP INCREMENTAL STIM TESTS 58
5.3.2. CONDUCTING INCREMENTAL STIM TESTS 60
5.3.3. INCREMENTAL STIM TEST VALUES 60
5.4. HEART RATE VARIABILITY (HRV) 61
5.4.1. SETTING UP HRV STIMULATION TESTS 61
5.4.2. CONDUCTING HRV TESTS 61
5.4.3. SYMPATHETIC SKIN RESPONSE 63
5.5. MULTI-CHANNEL EMG/IOM 64
5.6. MULTI-CHANNEL NERVE CONDUCTIONS 65
5.7. THE P300 TEST 65
5.7.1. GETTING STARTED 65
5.7.2. RUNNING THE TEST 67
5.7.3. HINTS AND FEATURES 67
5.7.4. EXPLANATION OF OPTIONS 69
5.8. THE ERG (ELECTRORETINOGRAM) TEST 71
5.8.1. ABOUT THE ERG TEST 71
5.8.2. CONFIGURING THE ERG PROTOCOL 71
5.9. THE EOG (ELECTRO-OCULOGRAM) TEST 72
5.9.1. ABOUT THE EOG TEST 72
Page 3
XLTEK NeuroMax
5.9.2. CONFIGURING THE E0G PROTOCOL 72
6. AV STIM 1000 73
6.1. AV STIM 1000 FRONT PANEL 73

6.2. AV STIM 1000 REAR PANEL 73
6.3. CONNECTING THE AV STIM 1000 74
6.4. WARNINGS AND CAUTIONS 75
6.4.1. W ARNINGS 75
6.4.2. CAUTIONS 75
6.5. CALIBRATION AND MAINTENANCE 76
6.6. SUGGESTED AEP PROTOCOLS 77
6.6.1. AEP IMPEDANCE CHECK 77
6.7. SUGGESTED VEP PROTOCOLS 77
6.7.1. VEP IMPEDANCE CHECK 78
6.8. ACQUIRING A FULLFIELD VEP RESPONSE 78
6.9. ACQUIRING A HEMIFIELD VEP RESPONSE 79
7. SETTING THE DEFAULTS 80
7.1. TEST MENU PARAMETERS 80

7.1.1. CREATING AN ELECTROMYOGRAPHY SUITE 81
7.2. EDITING TEST DEFAULTS 81
8. ADMINISTRATIVE FUNCTIONS 83
8.1. ADMINISTRATIVE FUNCTIONS 83

8.1.1. PATIENT DIRECTORY 84
8.1.2. MEMORY MANAGEMENT 85
8.1.3. BATCH PRINT 86
8.1.4. SYSTEM OPTIONS 86
8.1.5. EDIT REPORT FORMAT 87
8.1.6. EDIT SITE NAME LIST 87
8.1.7. EDIT EMG NOTEPAD 87
8.1.8. EDIT PATIENT INFORMATION FIELDS 87
8.1.9. CHANGING THE DATE ON STORED DATA 87
8.2. MANAGING THE REPORTS 88
8.2.1. RICH TEXT FILES (RTF) 88
8.3. EXTENDED WARRANTY SERVICES INFORMATION 89
9. APPENDIX 1: IN-SERVICE CHECKLIST 90
10. APPENDIX 2: TROUBLESHOOTING 93
10.1. SOFTWARE 95
10.2. NERVE CONDUCTIONS 95
Page 4
XLTEK NeuroMax
10.3. ELECTROMYOGRAPHY 95
10.4. ADMINISTRATIVE FUNCTIONS 96

10.4.1. EDITING STUDIES 96
10.4.2. INTERPRETATION MACROS 96
10.5. SIGNAL CLIPPING IN NCS AND EMG 97
10.5.2. STIMULUS ARTIFACT 97

10.5.3. ELECTRODE IMPEDANCE 98
10.5.4. SKIN PREPARATION 99
10.5.5. ELECTRODE TYPE AND PLACEMENT 99
10.5.6. STIMULATOR 100
10.6. AV STIM 103
10.7. PRINTING 103
10.7.1. NEUROMAX 103
10.7.2. PRINTER 103
10.8. RECOMMENDED USER PERFORMED MAINTENANCE 104
10.8.1. NEUROMAX ENCLOSURE 105
10.8.2. KEYBOARD 106
10.8.3. SCREEN 106
10.8.4. BACK PANEL/CONNECTORS 106
10.8.5. HEADBOX AND CABLE 106
10.8.6. STIMULUS PROBE AND CABLE 106
10.8.7. PRINTER AND CABLE 107
10.8.8. ELECTRODES AND ACCESSORIES 107
10.9. USER ADJUSTMENTS 107
10.9.1. NO ELECTRICAL STIMULUS 108
10.9.2. NO RESPONSE FROM ELECTRODES 108
10.9.3. LARGE STIMULUS ARTIFACT 109
10.9.4. NOISY DATA 110
10.9.5. UNIT DOES NOT POWER ON 111
10.9.6. ERROR MESSAGES 112
10.10. CHECKING CALIBRATION OF NEUROMAX 115
11. BLOCK DIAGRAM 116
INDEX 118
Page 5
XLTEK NeuroMax
NEUROMAX SAFETY AND STANDARDS CONFORMITY
STANDARDS COMPLIANCE AND NORMATIVE REFERENCES

EMG System, model "NeuroMax 1002" and “NeuroMax 1004"; rated 120/240V, 50/60Hz,
1.4A/0.7A; detachable cord connected; Class I;Type BF applied parts.
1. Type of protection against electric shock: Class I

2. Degree of protection against electric shock: Type BF
The NeuroMax and its accessories have been designed to comply with the following national
and international standards.
Table 1 – Safety Standard of Compliance and Normative References
CAN/CSA C22.2 No 601.1-M90 Medical Electrical Equipment part 1: General requirements

for Safety adopted IEC 601-1 2ed (90)
CSA 601.1 Supplement 1:1994 Supplement No 1-94 to CAN/CSA C22.2 601.1-M90 Medical
Electrical Equipment Part 1: General Requirements for
Safety
CSA 601.1 Amendment 2:1998 Amendment 2 to CAN/CSA C22.2 601.1-M90 Medical
Electrical Equipment Part 1: General Requirements for
Safety
UL Std No 2601-1 (2nd Edition) Medical Electrical Equipment part 1: General requirements
for Safety
IEC 601-1:1988 + A1:1991 + Medical electrical equipment - Part 1: General requirements

A2:1995 for basic safety and essential performance
IEC 60601-2-40 (1998-02) Medical Electrical Equipment part 2-40: Particular

requirements for the Safety of Electromyographs and Evoked
Response Equipment
Table 2 – EMC Standard of Compliance and Normative References
EN 60601-1-2 :2001 (2nd Edition) Medical Electrical Equipment, Part 1-2:General

Requirements for Safety - Collateral Standard:
Electromagnetic Compatibility - Requirements and Tests
IEC 61000-4-2:1995 / EN 61000-4- Electromagnetic compatibility (EMC) - Part 4-2: Testing and
2:2001 measurement techniques - Electrostatic discharge immunity
test
3:2006 measurement techniques - Radiated, radio-frequency,
electromagnetic field immunity test
4:2004 measurement techniques - Electrical fast transient/burst
immunity test
Page 6
XLTEK NeuroMax
5:2006 measurement techniques - Surge immunity test
6:2007 measurement techniques - Immunity to conducted
disturbances, induced by radio-frequency fields
IEC 61000-4-8 / EN 61000-4-8 Electromagnetic compatibility (EMC) - Part 4-8: Testing and
measurement techniques - Power frequency magnetic field
immunity test
11:2004 measurement techniques - Voltage dips, short interruptions
and voltage variations immunity tests
IEC 61000-3-2:2005 / EN 61000-3- Electromagnetic compatibility (EMC) - Part 3-2: Limits -
2:2006 Limits for harmonic current emissions
IEC 61000-3-3:1994 / EN 61000-3- Electromagnetic compatibility (EMC) - Part 3-3: Limits -

3:1995 +A1:2001 +A2:2005 Limitation of voltage changes, voltage fluctuations and flicker
in public low-voltage supply systems
CISPR 11:2004 / EN Industrial, Scientific and Medical (ISM) Radio-Frequency
55011:1998+A1:1999 & A2:2002 Equipment - Electromagnetic Disturbance Characteristics -
Limits and Methods of Measurement
ANSI C63.4:2003 American National Standard for Methods of Measurement of
Radio-Noise Emissions from Low-Voltage Electrical and
Electronic Equipment in the Range of 9 KHz to 40 GHz
CISPR 16-1-1: 2003 Specification for radio disturbance and immunity measuring
apparatus and methods.
Part 1-1: Measuring Apparatus
CISPR 16-2-1:2004 Specification for radio disturbance and immunity measuring
apparatus and methods.
Part 1-2: Conducted disturbances
FCC CRF47 Part 15, Subpart B Federal Communications Commission (FCC) - Unintentional
Class A Radiators
Page 7
XLTEK NeuroMax
DECLARATION OF COMPLIANCE FOR IEC 60601-1-2

Table 1 - Electromagnetic Emissions
Guidance and manufacturer’s declaration – electromagnetic emissions

The NeuroMax 1004/1002 is intended for use in the electromagnetic environment specified below. The customer or
the user of the NeuroMax 1004/1002 should assure that it is used in such an environment.
Emissions Compliance Electromagnetic environment - guidance

test
RF emissions Group 1 The NeuroMax 1004/1002 uses RF energy only for its internal function.
CISPR 11 Therefore, its RF emissions are very low and not likely to cause any
interference in nearby electronic equipment
RF emissions Class A The NeuroMax 1004/1002 is suitable for use in all establishments other
CISPR 11 than domestic and those directly connected to the public low-voltage power
supply network that supplies buildings used for domestic purposes.
Harmonic Class A
emissions IEC
61000-3-2
Voltage Complies
fluctuations/
flicker emissions
IEC 61000-3-3
Page 8
XLTEK NeuroMax
Table 2 - Electromagnetic Immunity
Guidance and Manufacturer’s Declaration – Electromagnetic Immunity

The NeuroMax 1004/1002 is intended for use in the electromagnetic environment specified below. The
customer or the user of the NeuroMax 1004/1002 should assure that it is used in such an environment.
Immunity test IEC 60601 Compliance Electromagnetic
test level level environment - guidance
Electrostatic Discharge ±6 kV contact Floors should be wood, concrete or
Complies
(ESD) ceramic tile. If floors are covered with
±8 kV air synthetic material, the relative humidity
IEC 61000-4-2 should be at least 30%.
Electrostatic fast ±2 kV for power Mains power quality should be
Complies
transient/burst supply lines that of a typical commercial or
IEC 61000-4-4 hospital environment.
±1 kV for
input/output
lines
Surge ±1 kV Complies Mains power quality should be
IEC 61000-4-5 differential mode that of a typical commercial or
hospital environment.
±2 kV common
mode
Voltage dips, short <5% UT Complies Mains power quality should be that
interruptions and voltage (>95% dip in UT) of a typical commercial or hospital
variations on power supply for 0.5 cycle environment. If the user of the
input lines NeuroMax 1004/1002 requires
40% UT continued operation during power
IEC 61000-4-11 mains interruption, it is recommended
(60% dip in UT)
for 5 cycles that the NeuroMax 1004/1002 be
powered from an uninterruptible
70% UT power supply or a battery.
(30% dip in UT)
for 25 cycles
<5% UT
(>95% dip in UT)
for 5 sec
Power frequency 3 A/m Complies Power frequency magnetic fields
(50/60 Hz) magnetic field should be at levels characteristic of a
typical location in a typical
IEC 61000-4-8 commercial or hospital
environment.
NOTE: UT is the AC supply voltage prior to application of the test level.
Page 9
XLTEK NeuroMax
Table 3 - Electromagnetic Immunity – for EQUIPMENT and SYSTEMS that are not LIFE-
SUPPORTING
Guidance and Manufacturer’s Declaration – Electromagnetic Immunity
The NeuroMax 1004/1002 is intended for use in the electromagnetic environment specified below. The customer or the user of
the NeuroMax 1004/1002 should assure that it is used in such an environment
Immunity test IEC 60601 Compliance Electromagnetic environment - guidance

test level level
Portable and mobile RF communications equipment
should be used no closer to any part of the NeuroMax
1004/1002, including cables, than the recommended
separation distance calculated from the equation
applicable to the frequency of the transmitter.
Recommended separation distance
Conducted RF 3 Vrms
150 kHz to 80 MHz
150kHz to 80MHz
IEC 61000-4-6
Complies
80MHz to 800MHz
Radiated RF 3 V/m
80 MHz to 2.5 GHz
IEC 61000-4-3 800MHz to 2.5GHz
where P is the maximum output power rating of the

transmitter in watts (W) according to the transmitter
manufacturer and d is the recommended separation
distance in meters (m).
Field strengths from fixed RF transmitters, as
determined by an electromagnetic sitea should be less
than the compliance level in each frequencyb.
Interference may occur in the vicinity of equipment
marked with the following symbol:
NOTE 1: At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection
from structures, objects and people.
a Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land
mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with
accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey
should be considered. If the measured field strength in the location in which the NeuroMax 1004/1002 is used
exceeds the applicable RF compliance level above, the NeuroMax 1004/1002 should be observed to verify normal
operation. If abnormal operation is observed, additional measures may be necessary, such as re-orienting or
relocating the NeuroMax 1004/1002.
b
Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.
Page 10
XLTEK NeuroMax
Table 4 - Recommended Separation Distances
Recommended separation distances between portable and mobile RF communications

equipment and the NeuroMax 1004/1002
The NeuroMax 1004/1002 is intended for use in an electromagnetic environment in which radiated RF
disturbances are controlled. The customer or the user of the NeuroMax 1004/1002 can help prevent
electromagnetic interference by maintaining a minimum distance between portable and mobile RF
communications equipment (transmitters) and the NeuroMax 1004/1002 as recommended below, according to
the maximum output power of the communications equipment.
Rated Separation distance according to frequency of transmitter (m)
maximum 150 kHz to80MHz 80 MHz to 800 MHz 800 MHz to 2.5 GHz
output power
of transmitter
(W)
0.01 0.12 0.12 0.23
0.1 0.38 0.38 0.73
1 1.2 1.2 2.3
10 3.8 3.8 7.3
100 12 12 23
For transmitters rated at a maximum output power not listed above, the recommended separation distance d
in meters (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is
the maximum output power rating of the transmitter in watts (W) according to the transmitter
manufacturer.
NOTE 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption
and reflection from structures, objects and people.
DECLARATION OF COMPLIANCE FOR FCC
Note: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
Warning: Changes or modifications not expressly approved by the manufacturer could

void the user's authority to operate the equipment.
Page 11
XLTEK NeuroMax
1. WELCOME TO THE
NEUROMAX
Congratulations, you have purchased the NeuroMax
from XLTEK, one of the world's top manufacturers of
neurodiagnostic equipment and software.
The NeuroMax offers full-featured EMG in a simple,

easy to use, and affordable line of instruments.
XLTEK NeuroMax is available in two and four-
channel format and provides you with the highest
performance and greatest reliability of any EMG
instrument on the market. From simple NCS studies
through to a complex quantitative EMG, the XLTEK
NeuroMax is the system you can rely on.
XLTEK NeuroMax 1002 CE

Two-channel neurodiagnostic for basic and
advanced NCS, EMG, and EP. Incorporates a large
12.1" XGA (1024 x 768) screen. Advanced
engineering and the latest in technology allow for
improved performance and speed, advanced NCS
capabilities,
advanced EMG capabilities, and advanced Multi-
Channel Studies.
XLTEK NeuroMax 1004 CE

Four-channel neurodiagnostic for basic and
advanced NCS, EMG, and EP. Incorporates a large
12.1" XGA (1024 x 768) screen. Advanced
engineering and the latest in technology allow for
improved performance and speed, advanced NCS
capabilities,
advanced EMG capabilities, and advanced Multi-
Channel Studies.
XLTEK Headboxes and Accessories

XLTEK provides two and four-channel amplifiers, AV
Stimulators, and a full range of accessories.
Page 12
XLTEK NeuroMax
1.1. INTRODUCTION
XLTEK is commitment to continual product
improvements and quality design to meet the needs
of our clients. We thus encourage all feedback and
any suggestions you have regarding any aspect of
the EMG system, the manual, our line of
accessories, and our support services.
1.1.1. INTENDED USE

The NeuroMax EMG is intended to be used as a
clinical electromyograph to acquire, display, store
and archive neurophysiological signals.
1.2. CUSTOMER SERVICE

XLTEK is committed to providing you with support
so you can operate the NeuroMax with ease and
confidence. If you need help, follow these steps to
find a solution:
Step 1: Document the Incident
Carefully document the incident step by step. If
possible, note error messages, the type of test and
what you did before the problem occurred, including
the sequence of keystrokes.
Step 2: Shut Down the NeuroMax
Sometimes you need to shutdown completely in
order to solve a problem. Press the MAIN MENU
key to return to the Main Menu. Turn the power off
to the unit. Make sure all cables are connected and
intact. Turn the power back on.
Step 3: Call or Email Technical Support
First, write down the serial number (located on the
back of the computer). Then phone XLTEK‟s
Customer Support at 1-800-303-0306 or contact
XLTEK Technical Support at [email protected].
Page 13
XLTEK NeuroMax
1.3. USING THE MANUAL

XLTEK is committed to providing you with clear
instructions and unqualified support so you can
operate our equipment with ease and confidence.
The manual presents step-by-step instructions

which take you through the testing, customizing,
and operation of the equipment and software so that
our system meets your specific needs. It will guide
you through the acquisition of a patient record and
its review, storage, and recall. You will learn how to
develop a report and to archive studies for future
reference.
For your convenience, a thorough Table of Contents
is provided which details the topics covered in each
chapter. An Index is also available at the back of the
manual.
The in-depth procedures describe the detailed

operation and customization of the EMG system.
The procedures, which are accompanied by
detailed graphics, are designed to tailor the system
to your specific circumstances. We encourage all
users to explore the manual and to take advantage
of everything that XLTEK has designed the EMG
system to do.
When going through the procedures, we

recommend that you read the whole section before
starting the sequence. Please follow the instructions
carefully.
We have also placed TIPS and NOTES alongside

the instructions. These will list Hot Keys, operation
tips, shortcuts, and testing information.
TIPS NOTES
Page 14
XLTEK NeuroMax
2. THE XLTEK NEUROMAX

The NeuroMax is designed to conduct a range of
tests, including Nerve Conduction Studies (NCS),
Electromyography Studies (EMG), and other tests
such as Evoked Potentials, Blink Reflex,
Incremental Stimulation, and Heart Rate Variability.
This chapter takes you through the Warnings and

Cautions you need to observe while operating the
NeuroMax and introduces you to its basic functions.
2.1. OPERATING CONDITIONS

The NeuroMax is designed for optimum
performance under safe conditions. To ensure the
safety of the operator and of the patient, please
read the following sections carefully.
2.1.1. ENVIRONMENT PARAMETERS

Temperature Range: +10 to + 40 degrees Celsius
Relative Humidity Range: 30 % to 75 %
Atmospheric Pressure Range: 700 hPa to 1,060 hPa
Altitude: To a maximum of 4600 meters above sea
level
2.1.2. TRANSPORT AND STORAGE

PARAMETERS
Ambient Temperature Range: – 40 to +70 degrees
Celsius
Relative Humidity Range: 10% to 100%, including
condensation
Atmospheric Pressure Range: 500hPa to 1,060hPa
Page 15
XLTEK NeuroMax
2.2. SPECIFICATIONS
Specification Value
General Description
Dimensions 4” (H) x 13” (W) x 13” (D)
Weight 11.4lbs (5.2kg)
Colour White
Materials Injection moulded PC ABS
chassis
External Connectors Headbox, Headphones,
Printer, Footswitch
(pneumatic)
Channels 4 (NeuroMaxCE 1004)
2 (NeuroMaxCE 1002)
Sampling Rate 60 kHz
Display
Size and Type 12.1” active matrix colour LCD
screen
Resolution 1024 x 768
Electrical Specifications
Maximum Rated 92 VA
Input Power
Heat Loss 92 Watts
Maximum Supply ± 10% for either 50 Hz or 60
Current Tolerance Hz transformer*
Electrical Supply ± 10% for either 50 Hz or 60
Frequency Tolerance Hz transformer*
Insulation Class and Class 1, Type BF
Type
Power Input Voltage, 120 VAC, 60 Hz, 1A
Frequency, and 230 VAC, 50 Hz, 0.4 A
Rated Current
Mains Connection Protectively grounded
detachable power supply cord
CMRR ~105 dB
Noise ~2.9 nV / √Hz
Page 16
XLTEK NeuroMax
Stimulator Specifications
Maximum Simulator ~450 V
Voltage
Maximum Stimulator 100 mA

Current
Stimulator Current ± 1%
Accuracy
Stimulator Duration ± 1%
Accuracy
Voltage Accuracy on ± 1%
Screen
* A power supervisor circuit shuts off power if

insufficient power is present.
2.3. WARNINGS AND CAUTIONS

The following Warnings and Cautions are marked
with a and must be followed very closely to
ensure the safety of both the patient and the user of
the NeuroMax and the AV Stim. It is therefore
important to read and observe ALL of the Warnings
and Cautions before attempting to use the
NeuroMax and the AV Stim.
If there is any malfunction or perceived malfunction
of the system, please call an authorized XLTEK
service representative immediately at 1-800-303-
0306. All internal system checks and/or service
must only be conducted by an authorized XLTEK
service representative.
IMPORTANT: 'SYSTEM' REFERS TO THE
NEUROMAX, AV STIM, AND ALL ACCESSORIES
ATTACHED TO IT.
The NeuroMax and AV Stim carry the ordinary

equipment classification (as per IEC 529) for the
level of protection against ingress of liquids. They
are not drip or splash proof.
Regarding protection against electrical shock, the

NeuroMax and AV Stim are classified as Class I
devices (as per EN 60601-1). The NeuroMax
Page 17
XLTEK NeuroMax
requires a properly grounded electrical outlet. The

mode of operation for both the NeuroMax and AV
Stim is continuous operation.
2.3.1. WARNINGS
Warnings MUST be followed when using the
equipment. Warnings apply to conditions which can
injure the patient and/or the operator.
WARNING: Care must be taken in the

delivery of any level of stimulus. If used
improperly, injury may be caused to the
patient. The delivery of stimulus to the
patient is done through the Start/Stop key
on the NeuroMax and the stimulus probe.
WARNING: The level of stimulator

intensity is controlled by the Up/Down
arrows on the NeuroMax and the
stimulation probe and is displayed on the
active test screen in mA. Close attention
must be paid to the level of stimulus
intensity and the duration of the impulse.
This unit has enough electrical power to
harm a patient if used improperly.
WARNING: This system must only be

plugged into a properly grounded
electrical outlet. The internal isolation
transformer of the system must not be
bypassed, under any circumstances.
WARNING: Hazardous voltages are

exposed when the lid of the NeuroMax is
removed.
WARNING: This system is not suitable

for use in the presence of flammable
mixtures. The system is not AP or APG
rated.
WARNING: Do not turn the system on

until all cable connections are made and
their integrity is checked.
Page 18
XLTEK NeuroMax
WARNING: The proper use of this

device for its intended purpose can only
be assured once all instructions have
been read and understood. If there are
any questions regarding the operation of
this device, contact your XLTEK
representative at once.
WARNING: The sale, distribution, or

use of this device is restricted to by, or on
order of, a licensed medical practitioner.
WARNING: The NeuroMax and the AV

Stim are Type BF devices (as per EN
60601-1) regarding degree of protection
against electrical shock. The BF device is
an applied part isolated from other parts
of the EQUIPMENT to such a degree that
that no current higher than the PATIENT
LEAKAGE CURRENT allowable in
SINGLE FAULT CONDITION flows if an
intended voltage originating from an
external source is connected to the
PATIENT, and thereby applied between
the APPLIED PART and the ground. All
of the patient connections of the
NeuroMax are electrically isolated;
however, these connections are not
intended for direct cardiac contact.
WARNING: The NeuroMax provides

sufficient electrical isolation for the
patient through its own internal isolation
barrier. Please ensure that a printer
attached to the NeuroMax through the
USB port passes an appropriate safety
certification.
WARNING: Non-medical electrical
equipment (printers and computers) may
be attached to the NeuroMax only if
those devices pass appropriate safety
certifications. In the case of printers and
computers they should pass IEC 950 or
equivalent standard.
Page 19
XLTEK NeuroMax
WARNING: Possible interference with

EMG and Nerve Conduction signals may
occur in certain situations (i.e. poor
grounding in circuitry, close proximity to
other instrumentation such as an MRI).
2.3.2. CAUTIONS
Cautions must be noted when using the equipment.
Cautions apply to conditions which may damage the
NeuroMax.
CAUTION: It is recommended that the

stimulator probe be disinfected between
patients with 70% isopropyl alcohol. This
is not an appropriate method of
sterilization if the stimulator is used
invasively.
CAUTION: Turn off all system power
and disconnect the power cord from the
system and the wall before attempting to
clean the unit. The NeuroMax and the AV
Stim can be wiped clean with a damp
cloth using non-conductive distilled
water, electrically non-conductive inert
surfactants, or a cold sterilizing agent. It
is important to dry off the units quickly.
Avoid letting liquid seep into any of the
internal electronics of the system. The
screen of the NeuroMax is more sensitive
to liquid damage than the other
components of the NeuroMax, so be
careful to wipe off liquid spots
immediately. Use a soft cloth on the
screen. Do not use any abrasive cleaner
on the system. Refer to AV Stim Manual
for detailed cleaning instructions for the
headphones and goggles used with the
AV Stim.
CAUTION: Method of sterilization or
disinfection classification: no method.
CAUTION: Inspect all cables and

connections (especially the power cord)
often for signs of fraying or other
damage. Do not operate either the
Page 20
XLTEK NeuroMax
NeuroMax or the AV Stim if you suspect

damage to any of the cables or the power
cord.
CAUTION: Do not leave any cables
attached to the back panel of the
NeuroMax / AV Stim when transporting
the unit -- this may cause the back panel
connections to become loose, or
malfunction during operation of the unit.
CAUTION: Pay particular attention to
the care of the NeuroMax screen. Do not
attempt to remove the protective cover.
The screen itself uses a glass panel,
which may crack or break if it is dropped
or bumped on a hard surface. Handle
with care.
CAUTION: Do not turn on the power to
the NeuroMax and/or the AV Stim
immediately after bringing either unit from
a cold environment to room temperature.
Allow the units to assume ambient
environmental temperature (one-hour
warm up).
Page 21
XLTEK NeuroMax
2.4. EXPLANATION OF LABELING

SYMBOLS
A number of symbols appear on the various
components of the NeuroMax system. Please consult
the table below for their meanings and significance.
Symbol IEC Publication Description

384 ATTENTION:
Consult
Accompanying
Documents
417-5019 Protective Earth
(Ground)
878-02-02 Type BF
Equipment
878-03-01 Dangerous Voltage
417-5032 Alternating Current
417-5007 Power On
417-5008 Power Off
Medical Device
Directive CE Mark
0086 93/42/EEC
Canadian
Standards
Not Applicable Association
(indicates safety
approval by)
Page 22
XLTEK NeuroMax
2.5. MAIN MENU

The NeuroMax opens to the Main Menu screen and
lists the five menu choices available to you.
Figure 2.1: Main Menu
Choices 1-3 are the studies available on the

NeuroMax:
(1) Nerve Conduction: Test motor nerve

conduction, sensory nerve conduction, F-
Wave, Rep Stim, and H-reflex.
(2) Electromyography: Test muscle activity
with FreeRun EMG and Triggered EMG.
(3) Other Tests: Includes Evoked Potentials,
Blink Reflex, Incremental Stim, and Heart
Rate Variability, Multi-Channel EMG, and
Multi-Channel NCS.
Page 23
XLTEK NeuroMax
2.6. KEY PAD

The keypad is divided into four sections, each with
its own set of functions.
Function Keys Control Keys
Alphanumeric Select Keys

Keyboard
Figure 2.2: Key Pad
Alphanumeric Keyboard: Follows the familiar

QWERTY pattern used on most computer
keyboards.
Control Keys: Operate audio, stimulation, and

trigger levels.
Page 24
XLTEK NeuroMax
Figure 2.3: Control Keys
Select Keys: The Select arrows control the

option selections and the Select key is main entry
key.
Figure 2.4: Select Keys
Function Keys: Perform and customize

neurological tests.
Page 25
XLTEK NeuroMax
Figure 2.5: Function Keys
The Function key operations are listed below:
TRACE FUNCTION KEY

Move, smooth, re-assign, and
superimpose traces
Review stored EMG
Number of traces to raster
SETTINGS FUNCTION KEY

Low-frequency, high-frequency and
notch filters
Amplifier and Display Gain, timebase
and sweep delay
Trigger delay/slope
CURSORS FUNCTION KEY

Latency and amplitude cursors
Adjust position and add cursors
DISTANCE FUNCTION KEY

Segment distances in mm
Conduction velocity calculated
STIMULATOR FUNCTION KEY

Pulse duration, stim frequency, mode
and max. intensity
Number of pulses/train
Page 26
XLTEK NeuroMax
AV Stimulator parameters
NOTES FUNCTION KEY

Needle EMG notepad
Enter test comments
Edit site names
ERASE FUNCTION KEY

Erase single or multiple traces
Erase sets of data
AVERAGER FUNCTION KEY

Turn Averager On/Off
Acquire EP responses
SELECT FUNCTION KEY

Choose highlighted menu selection
2.7. HOT KEYS

The Hot Keys activate functions during an
acquisition, providing a quick and immediate
response. They will be noted in the Notes and Tips
when applicable.
2.7.1. SENSORY NERVE CONDUCTION HOT

KEYS
KEY FUNCTION
Space Bar if in full screen mode, averaging and
single acquisition mode, deletes the
latest acquisition from the average
X post processing artifact extraction
2.7.2. ELECTROMYOGRAPHY HOT KEYS
KEY FUNCTION
TRIGGER go to Triggered from FreeRun
1,2
F go to FreeRun from Triggered
Page 27
XLTEK NeuroMax
2.7.3. EVOKED POTENTIAL HOT KEYS
KEY FUNCTION
A change the Acceptance level of the
signal (entered as a percentage of
the A/D converter full scale value)
D Display only certain traces
F Flip to show the next or previous set
of data in the data box
L set-up the left ear for Audio
threshold test (Left = 15 dB nHL . Audio tests
Stimulus, Right = 0 dB Noise) are only valid when
set-up the right ear for Audio the AVStimulator is
R attached and in Audio
threshold test (Left = 0 dB Noise, Stimulation mode.
Right = 15 dB nHL Stimulus)
Space Bar show live trace
Page 28
XLTEK NeuroMax
2.8. CREATING A PATIENT FILE

An important feature of the NeuroMax is its ability to
save multiple patient files and tests. This allows you
to recall, edit, and print previously stored data.
The NeuroMax will
The first step is to create a patient file. Once that is
notify you if you start
a test without creating completed, you can save tests and generate
a patient file first. reports.
You can access the Patient Information screen from

the Main Menu and from each of the three Test
menus.
1. Press the Patient Info key to open the
Patient Information screen.
Figure 2.6: Patient Information
2. Enter the patient's information, in each of the

fields. The yellow bar marks the field you are
You can also use the
Up/Down arrows, the working in and the Select key takes you to
Select key, and the
keyboard keys to move the next field.
the Entry field.
Page 29
XLTEK NeuroMax
3. When all relevant information has been entered,

While a patient is
press the Patient Info key to exit to the Main active, the patient
Menu. information can be edited
and/or a new patient file can
4. Press the Patient Info key to open the Patient be created.
Information screen to the patient's data.

5. At the bottom of the screen, you can choose
whether to edit the existing patient information or
The Edit Current Patient to create a new patient file.
setting is highlighted for
you by the NeuroMax. 6. To edit the current patient file, press the Select
key.
7. To create a new patient file, press the Right
arrow to highlight New Patient and then

press the Select key.
Once a test is completed, and you have returned to

either the Main Menu screen or to any of the three
Test Menus, that particular test will be saved and
filed under the active patient name. These tests can The Patient
be recalled and edited at any time from the Patient Directory is found in
the Administrative
An Active file is a Directory. Functions. See Ch. 8
patient file that is for more details.
still open and new If the NeuroMax is turned off, the patient file is no
data can be added. longer active and must be recalled from the Patient
Directory for review.
2.9. GENERATING TEST REPORTS

Once you have established a patient record, you
can proceed to the testing stage. However, it is
likely that you will need to record, store, and
distribute the test data. Thus you will have to
generate reports. The following sections show you
how to operate the NeuroMax report function and
how to design it to your specifications.
2.9.1. REPORT FUNCTIONS

The first method of reporting is to access the report
functions while a patient is active. See Section
“Creating a Patient File”
Page 30
XLTEK NeuroMax
1. From the NeuroMax Main Menu screen in an
active patient file, press the Report key.

You can also access
the Report Functions
fromwithin any of
the three test menus.
Figure 2.7: Patient Directory
All reporting functions can be completed by

highlighting the appropriate patient and selecting
the following functions.
REPORT FUNCTIONS
View Report You can view the report on
screen before printing to
verify or inspect the data
Edit Report You can edit the tests, and
the data within a test, to
customize the report
Interpretation Gives you a free text area to
type a summary of the data
(interpret what will be printed
on the final report)
Print Report Prints the report
Only
Print Report Prints the report and a
and condensed version of the
Waveforms waveforms
If a patient is not active, then the reporting functions
must be accessed through the Patient Directory in
the Administration Menu.
Page 31
XLTEK NeuroMax
1. From the NeuroMax Main Menu screen, select

Administrative Menu and then press the Select
key .
2. From the Administrative Functions Menu, select
Patient Directory and then press the Select
key.
3. Select the function and press the Select key.
Page 32
XLTEK NeuroMax
3. NERVE CONDUCTION TESTS

This chapter will deal with the operation of the
NeuroMax in its Nerve Conduction Studies mode of
operation.
The most important function to become familiar with

is the ASSIGN function. The Assign function has
been designed to streamline the process of
acquiring Motor and Sensory Nerve Conductions
responses. The Assign function will enable the user
to peruse many acquired responses and relevant
data values (i.e. latency, amplitude, etc) on the
same screen at the same time, enabling them to
efficiently choose the best response, without having
to SAVE EACH INDIVIDUAL response during the
course of the study.
When a stimulus pulse is delivered, the response

will be displayed in the box at the top left-hand
corner of the screen in the Acquisition Trace Area.
Once you have acquired a satisfactory trace
response you must ASSIGN it to the Assigned
Trace Area by assigning that trace a number using
the numeric keypad. Refer to figure 3.2 for a
diagram of the screen trace areas.
As with other testing modes on the NeuroMax, you

can create custom testing protocols and have them
saved for immediate selection, without having to
change all of the stimulating and recording
parameters each time you do a particular test. Test
Menu Parameters are covered in chapter seven (7).
Page 33
XLTEK NeuroMax
3.1. MOTOR AND SENSORY NERVE

CONDUCTIONS
Before you begin the Motor and Sensory Nerve
Conduction Studies, set up the Patient Information
screen to create an active patient file and then
return to the Main Menu screen.
3.1.1. SETTING UP A NERVE CONDUCTION

STUDY
1. Using the Select arrows, select Nerve

Conduction Studies from the Main Menu and
then press the Select key to open the Nerve
Conduction Test Menu.
Figure 3.1: NCS Test Menu Screen

2. In Section 1, choose the appropriate Nerve
using the Select arrows , and then press the
Select key to continue.

3. In Section 2, choose either the Motor Nerve
Conduction (MNC) study or Sensory Nerve
To return to the Conduction (SNC) study using the Select arrows
NCS Test Menu,
press the Test and then press the Select key to continue.
Menu key.
Page 34
XLTEK NeuroMax
4. In Section 3, choose the side you wish to test

and then press the Select key to open the Nerve
Conductions Studies (NCS) Test screen.
Acquired Trace Area Live Data Box
Data Box
Assigned Trace Area
All test screen Stimulator Box

graphic settings are
for demonstration
Figure 3.2: NCS Test Screen
purposes only.
Acquired Trace Area: Shows the most recent

acquisition.
Assigned Trace Area: Stores up to eight traces per

NCS Test.
Live Data Box: Displays the cursor values for the

acquired trace.
Data Box: Shows the cursor and calculated values

for the assigned traces.
Stimulator Box: Displays the status of the electrical

stimulus (stim. level, mode duration, and
frequency).
The Nerve Conductions Studies (NCS) Test Screen

is now active. The Acquisition Trace Area displays
traces that have just been acquired. You can
enlarge the Acquisition Trace Area to acquire a
waveform.
1. Press the Select key to activate Full Screen

Mode and then acquire your waveform.
Page 35
XLTEK NeuroMax
2. To return to standard screen size, press the

Select key.
3.1.2. CONDUCTING AN NCS

Make sure that all the electrode connectors are
firmly in place.
1. Adjust the stimulus intensity by pressing the

The Stimlevels
Stim Up/Down arrows on the Control are recorded in the
The stimulus intensity keypad. Stimulator box at the
may also be controlled by bottom-right of your
using the Up/Down 2. To activate the stimulus probe, press the screen.
arrow keys on the stim
probe. See System Start/Stop Control key, the center button
Options in Ch. 8.
on the hand held stimulator to obtain the
waveform, or press and release the footswitch.
3. Repeat until desired waveform is obtained.
4. Number the waveform and assign waveform to
trace position using appropriate number key (1-
8) . The waveform will be placed in the

Assigned Trace area.
5. Move to next stimulus site and then repeat
procedure.
6. To save the test data and to exit the test, press
the Test Menu key or the Main Menu
key.
Page 36
XLTEK NeuroMax
MNC/SNC STUDY HINTS AND

FEATURES
 -- If a particular stimulus site has no response, use the
Cursors key to move the Latency 1 cursor to the „0'
position (far left) and the report will display „NR' for the
appropriate site.
 -- Pressing the Averager key will automatically average
successive traces and the averaged trace will be
displayed in the acquisition box. Once the desired
response is obtained, the averaged waveform may be
assigned to the appropriate position and the number
of averages will return to zero to begin the next
stimulus site. This feature may be used in conjunction
with repetitive or train stimulus mode to quickly
average more than one response.
 -- External Triggers can be connected to the NeuroMax
using the BNC connector on back panel.
 -- Trigger mode and parameters can be selected by You can also
pressing the Stimulator key, or through the Defaults activate the Default
setting box by pressing
Test Editing page (press Default ). Backspace + C.
3.1.3. ABOUT THE REP STIM TEST

The NeuroMax‟s Repetitive Stimulation program (Rep
Stim) is based upon standard testing protocols. The
testing protocol includes up to three testing conditions,
generically named PRE, POST and RECOVERY.
These denote the baseline study (PRE), the
conditioned response study (POST), and a third test
performed two minutes after conditioning of the
response (RECOVERY). The Rep Stim program is
divided into two sections: 1. SET UP procedure 2.
RECORD procedure.
When Rep Stim is selected from the test menu, the

screen appears as it does for any MNC or SNC test;
however, the top line of the Acquisition Trace Area
displays the title SET UP. The first step in the test is to
attain a maximal CMAP. While you are in the set up
mode, the maximal CMAP can be attained by
Page 37
XLTEK NeuroMax
delivering a single shot stimulus in exactly the same

manner as in an MNC test, then changing the stimulus
parameters (intensity, duration, etc.), and then
stimulating again until the desired CMAP is attained.
Once you have obtained the maximal CMAP, and the

stimulus parameters are accurate for the Rep Stim
Recording procedure, press the SELECT button. You
will see the screen change slightly in appearance. The
top of the screen will display RECORD. You now
simply press the START/STOP key for the test to
begin.
The NeuroMax will calculate and display the Amplitude

(in mV) and the area (in mVms) for both the baseline
response and the test response, as well as the %
decrement for both the amplitude and area between
the baseline and test responses.
Post-acquisition, you can change the test trace

number so that a different trace is used as the test
trace (press TRACE to access this function). In the test
settings for the Rep Stim test, you can set the default
trace numbers for both the baseline and test traces.
3.1.4. PERFORMING A REP STIM TEST
1. From the main menu, highlight Nerve

Conduction Studies and then press SELECT (or
hit # 1).
2. From the Nerve Conduction Studies test menu,
choose the nerve you want to test, then
SELECT. Now choose Rep Stim, then SELECT
and, if required, choose the side you want to
test, then SELECT once more.
3. The Rep Stim test screen will now appear, with
the phrase SET UP at the top of the screen.
NOTE: A maximal CMAP must be attained before
The stimulus intensity you can move to the RECORD screen.

may also be controlled 4. Adjust the stimulus intensity by pressing the
by using the Up/Down The stimulator
arrow keys on the stim STIM UP/DOWN arrows. levels are shown in the
probe. See System Stimulator box.
Options in Ch. 8.
Page 38
XLTEK NeuroMax
5. To activate the stimulus probe, press the

START/STOP key, or the trigger button on the
stimulator, and obtain a waveform.
6. Repeat until the desired waveform is obtained.
7. When the desired M-Wave response has been
obtained, press SELECT to enter the RECORD
mode.
Figure 3.3: Rep Stim Test Screen – Record Mode
8. Press the START/STOP key to begin data

acquisition for the Pre mode. The responses will
be displayed directly in the trace data area, and
the amplitudes, areas, and % decrements for the
baseline and test traces will automatically be
calculated and displayed in the data table.
9. If the Pre-mode data acquisition is
unsatisfactory, you may erase the traces and
begin again. If the response is satisfactory,
continue to the next phase of the evaluation.
10. At the conclusion of the next phase of the test,
press the START/STOP key to begin data
acquisition for the Post mode.
Page 39
XLTEK NeuroMax
11. After the prescribed recovery time period has

elapsed, press the the START/STOP key to
begin data acquisition for the Recovery mode
NOTE: If your test protocol requires more than three
(3) sets, press 'r' on the standard keyboard to scroll to
another test screen.
12. The data from each of the three test conditions

are automatically entered into the data table and
the final report. If you wish, you may get an
individual test report, including waveforms, by
pressing REPORT, and selecting SCREEN
COPY.
13. To return to the test menu and do another test,
press TEST MENU.
14. To return to the main menu, press MAIN MENU.
3.1.5. ABOUT THE F-WAVE TEST
The F-Wave nerve conduction protocol in the
NeuroMax has functionality similar to the Repetitive
Stimulation protocol previously described. Like the
Rep Stim program, the F Wave study is divided into
two sections: 1. SET UP procedure
2. RECORD procedure.
When F-Wave is selected from the test menu, the

screen will appear as it does for any MNC or SNC
test; however, the top line of the Acquisition Trace
Area displays the title SET UP. The first step in the
test is to determine the stimulus characteristics
needed for the recording procedure. This is done by
delivering a single shot stimulus in exactly the same
manner as in an MNC test, then changing the
stimulus parameters (intensity, duration, etc.), and
then stimulating again until the desired M-Wave
response is obtained. Once you have obtained the
desired M-Wave response and the stimulus
parameters are where they should be for the F
Wave recording procedure, press the SELECT
button.
Page 40
XLTEK NeuroMax
You will see the screen change slightly in

appearance. The top of the data area now displays
RECORD, and the screen is divided into two areas.
The left side of the screen has the same sensitivity
factor as the F-Wave set up routine, while the right
side of the screen has a separate F-Wave
sensitivity. By default, the F-Wave gain will be 10%
of the M-Wave gain from the set-up routine. The two
gain areas are separated by a vertical red line
drawn on the screen. The whole screen is
continuous in timebase. Once you have pressed
SELECT to enter the RECORD mode, simply press
the START/STOP key to begin the train of stimuli
and recording of the M- and F-Wave responses.
By default, the NeuroMax assumes that the stimulus

used will be single shot stimulation for the set up
and then change to train stimulation for the record
mode, but these defaults can easily be changed if
required. The F-Wave protocol allows for the
acquisition of up to 20 responses on one screen. If
you want to repeat a test, you can either erase the
existing traces and then acquire new data, or you
can save the existing test by going back to the test
menu and re-selecting F-Wave once again.
3.1.6. PERFORMING AN F-WAVE TEST
1. From the main menu, highlight Nerve

Conduction Studies and then press SELECT (or
hit # 1).
2. From the Nerve Conduction Studies test menu,
choose the nerve you want to test, then
SELECT.
3. Choose F-wave, then SELECT.
4. If required, choose the side you want to test,
then SELECT once more.
5. The F-Wave test screen will now appear, with
The stimulus intensity the phrase SET UP at the top of the screen. The stimulator
may also be controlled levels are shown in the
by using the Up/Down Stimulator box.
arrow keys on the stim
probe. See System
Options in Ch. 8.
Page 41
XLTEK NeuroMax
NOTE: A proper M-Wave response must be

obtained before you can move to the RECORD
screen.
6. Adjust the stimulus intensity by pressing the
STIM UP/DOWN arrows.
7. To activate the stimulus probe, press the
START/STOP key, or the trigger button on the
stimulator, and obtain a waveform.
8. Repeat until the desired waveform is obtained.
9. When the desired M-Wave response has been
obtained, press SELECT to enter the RECORD
mode.
In F-Wave testing,
the acquisition area is
divided into a split screen
by a vertical red line. The
left side has the same gain
factor as the set-up
routine, while the right side
has an independent "F-
Wave" sensitivity. The
default setting of this
sensitivity is 10%of the
M-Wave gain.
Figure 3.4: F-Wave Test Screen – Record Mode

10. Press the START/STOP key to begin data
acquisition.
11. Press CURSORS to adjust the F-Wave latency
cursor. To calculate F-Wave amplitude, you
must first superimpose all traces (TRACE
function).
NOTE: If response is absent, scroll latency cursor to '0'
(far left) and report will display response as 'NR'.
Page 42
XLTEK NeuroMax
12. The data acquired for the test is automatically

analyzed with M- and F-Wave latencies directly
imported into the data table and into the final
report. If you want, you may get an individual
test report, including waveforms, by pressing
REPORT, and selecting SCREEN COPY.
13. To return to the test menu and do another test,
press TEST MENU.
14. To return to the main menu, press MAIN MENU.
F-WAVE AND REP STIM TESTS HINTS

AND FEATURES
 -- There are three modes in which potentials can be
recorded with the differences between the modes lying
Press the
Stimulator key to in the number of times and frequency at which the
set mode operation. patient is stimulated.
i. Single Mode: a single stimulus applied to a patient
each time the Start/Stop Control key is pressed.
This has the advantage of allowing random time
intervals between successive stimuli. The Inter-
Stimulus Interval is controlled by the user.
ii. Repetitive Mode: set for an unlimited number of
stimuli. The times between stimuli at a given
frequency are pre-set and the mode is started and
stopped using the Start/Stop Control key.
iii. Train Mode: the stimulator will automatically turn
off after the set number of stimuli have been
delivered.
 If a particular stimulus site has no response, use the
Cursors key to move the Latency 1 cursor to the „0'
position (far left) and the report will display „NR' for the
appropriate site.
 While Rep-Stim testing, there are three sets of

responses that may be obtained per test. If more sets
are desired, and you do not wish to go through the set-
Page 43
XLTEK NeuroMax
up procedure again, press R ( Repeat). The current

sets will be saved and you will be returned to the Rep-
Stim record screen with the same set-up, ready to
again acquire responses.
 Press the Trace key to designate a different
comparison test response.
3.1.7. SETTING UP AN H-REFLEX TEST
1. Using the Select arrows, select Nerve

Conduction Studies from the Main Menu and
To return to the then press the Select key to open the Nerve
NCS Test Menu,
press the Test Conduction Test Menu.
Menu key. 2. In Section 1, choose the appropriate Nerve
using the Select arrows and then press the
3. In Section 2, choose the H-Reflex Test using
the Select arrows and then press the Select key
to continue.
and then press the Select key to open the H-
Reflex Test screen.
3.1.8. ACQUIRING H-REFLEX RESPONSES
1. To begin the train of stimuli and to acquire

responses, press the Start/Stop Control key.
2. After each successive sweep, increase the The stimulus intensity
may also be controlled by
stimulation intensity using the Stim Up/Down using the Up/Down
arrows on the Control keypad. arrows on the stimprobe.
See SystemOptions in
3. Once an adequate H Wave has been obtained Ch. 8.
press the Start/Stop Control key to stop.

4. Adjust stimulus mode by pressing the Stimulator
key, or make changes to defaults by pressing
the Default key on the keyboard.
Page 44
XLTEK NeuroMax
4. EMG TESTS
This chapter will deal with the operation of the
NeuroMax in its EMG (Electromyography) Studies
mode of operation. The NeuroMax has many views
of the data on screen to view single traces, multiple
traces in a raster, single traces with multiple
triggered sweeps captured, compressed EMG data
in the real-time window. The NeuroMax
incorporates two triggers that may be adjusted
independently. The first trigger is amplitude/slope.
The second trigger acts as a discriminator that
allows you to look at smaller potentials
The NeuroMax will store the latest ten seconds of

an EMG study. You can choose to review it as a
compressed EMG or as a real-time display, with a
sweep of 5 ms per division. The memory buffer will
automatically be cleared after each new test muscle
or with a new needle insertion point.
4.1. SETTING UP THE EMG TEST

MENU
Before you begin Electromyography Studies, create
an active patient to set up the patient information
screen and then return to the Main Menu screen.
The NeuroMax is set to run two EMG test formats:

Free Run and Triggered. Sections 4.2 and 4.3 show
you how to perform an EMG acquisition and which
test to choose.
4.1.1. SETTING UP AN EMG
1. Using the Select arrows, select

Electromyography from the Main Menu and
To return to the then press the Select key to open the
Test Menu, press
the Test Menu Electromyography Test Menu.
key.
Page 45
XLTEK NeuroMax
2. In Section 1, choose the appropriate Muscle or

Suite using the Select arrows and then press the
3. In Section 2, choose either the Free Run Test or
the Triggered Test using the Select arrows and
then press the Select key to continue.
and then press the Select key to open the Free
Run test screen.
Figure 4.1: Free Run Acquisition
4.1.2. ACQUIRING AN EMG
1. To start the acquisition, press the Start/Stop

Control key.
Adjust the Audio keys
2. To choose different gains, use the Up/Down
before you begin to
avoid excessive arrows.
volume levels.
3. To end the acquisition, press the Start/Stop
Control key.
4. To classify the results or enter comments, press
When you select
the Notes key. TEXT entry, press the
Select key to record a
text note. Maximum120
characters.
Page 46
XLTEK NeuroMax
5. Use the Select arrows to change the fields and

values in the Notes Box and then press the
Select key to record entry.
6. Press the Test Menu key to select new muscles
to test.
Press the Settings key 7. Repeat Steps 1-5 until you have completed test
to review your
Acquisition settings. requirements.
8. To review the acquisition, see section 4.3 or
press the Main Menu key to exit the test.
Page 47
XLTEK NeuroMax
4.2. FREE RUN EMG FEATURES
4.2.1. REVIEWING FREE RUN EMG

You can review the most recent acquisition you
have just completed, monitor an audio portion of the
test, and save waveforms.
1. After completing the Notes, press the Trace key

to open the option box at the bottom of the
screen.
2. Review is selected as the value, so press the
Select key to review the acquisition.
3. Press the Left/Right arrows to move the window
box forward or backward.
4. Audio Replay is highlighted. Press the Select
key to play the last 10 seconds of audio.
5. Use the Up/Down arrows to select any of the
other options, including the option to save the
current sweep.
4.2.2. ANALYZING TURNS AND AMPLITUDE

You can analyze Turns and Amplitude while you are
acquiring real-time EMG data or after it has been
acquired.
Operating
instructions are
1. Press the Select key to perform a Turns and
listed at the bottom
of the screen. Amplitude analysis.
2. Press the Left/Right arrows to move the
Analysis Window.
3. Press the Trace key to display a Power
Spectrum analysis on the screen.
Page 48
XLTEK NeuroMax
4.3. TRIGGERED EMG FEATURES

When setting up the EMG test (see Section 4.1),
choose Triggered Test. The Triggered EMG
program uses one or two triggers to discriminate
and capture various motor unit potentials. The first
trigger is an amplitude/slope trigger and each EMG
sweep which crosses the trigger will be copied to
the "raster area." The second trigger is an
"exclusion" trigger.
Figure 4.2: Triggered EMG
4.3.1. ACTIVATING TRIGGERS
The NeuroMax is automatically set to Trigger 1. The When the

Trigger Slope is
active trigger levels are shown at the bottom of the negative, Trigger 2 (the
left screen. See Figure 4.2. exclusion trigger)
negative value is greater
1. To adjust trigger amplitude levels, press the (higher on the screen)
than Trigger 1. When
Trigger Up/Down Control arrows. trigger slope is positive,
Trigger 2 positive value
2. To activate Trigger 2, press the Trigger 1,2
is greater (lower on the
Control key. screen) than Trigger1.
3. To adjust Trigger 2 amplitude levels, press the

Trigger Up/Down Control arrows.
Page 49
XLTEK NeuroMax
4.3.2. SAVING A TEST
1. When a number of rastered traces are on the

You can save
screen, press the Select key to save the test. either the highlighted
or averaged waveform
2. To adjust the number of waveforms to raster, (average of all the
rastered waveforms).
press the Trace key.
3. To adjust the cursors in the selected and the
averaged waves, press the Cursors key.
4.3.3. ANALYZING AND REVIEWING

MOTOR UNITS
1. Recall the test file from Patient Directory

See chapter on 2. Use Left/Right arrows to highlight (red) box The Up/Down arrows
Test Recall select which of the
Procedures. containing the motor unit to be edited. waveforms to
highlight.
3. Press the Cursors key and then use the
Left/Right arrows to move the highlighted
(green) cursor.
4. Press the Up/Down arrows to highlight the next
cursor.
5. Press the Cursors key to exit the editing cursor
mode.
5. OTHER TESTS
The NeuroMax conducts several other tests,
including Evoked Potentials, Blink Reflex,
Incremental Stim, Heart Rate variability, and P 300.
5.1. OTHER TESTS

Before you select any of the Other Tests, you need
to set up the patient information screen to create an
active patient file and then return to the Main Menu
screen.
Page 50
XLTEK NeuroMax
5.1.1. SETTING UP EVOKED POTENTIALS

(EP)
1. Using the Select arrows, select Other Tests

from the Main Menu and then press the Select
key to open the Other Tests Menu.
To return to the Other 2. In Section 1, choose the appropriate test using
Tests Menu, press the
Test Menu key. the Select arrows and then press the Select key
to continue.
3. In Section 2, choose EP (Evoked Potentials)
using the Select arrows and then press the
and then press the Select key to open the EP
Test screen.
Figure 5.1: EP Test
5.1.2. CONDUCTING EVOKED

POTENTIALS
The Evoked Potentials test screen is similar to that

of the Nerve Conductions. The gains (for all
channels) and timebase are shown on the top of the
acquisition box and the cursor, data, and stimulator
boxes are located to the right of the screen.
Page 51
XLTEK NeuroMax
1. Press the Start/Stop Control key to begin

stimulating.
2. Press the Averager key to begin acquiring data.
3. Once a sufficient number of averages has been
You can
obtained, press the Averager key to begin complete four sweep
sets of averages.
acquiring the next set of traces.
4. Once acquisition of signals is completed, press
the Start/Stop Control key to end the
Use Select arrows to stimulation.
move cursor and to
select new cursors. 5. Press the Cursor key to mark signals.
See instructions
bottom-right screen. 6. Press the Test Menu key to exit and set up new
test or press the Main Menu key to exit the test. External Triggers
are connected to the
EVOKED POTENTIALS HINTS AND NeuroMax via the BNC
FEATURES connector on back panel.
Trigger mode and
 There are two different gains available.
parameters are selected by
i. Amplifier Gain: the actual input gain of the pressing the Settings key
amplifiers. This gain influences the rejection level of or through Defaults Test
Editing page (press Default
the signal. or the Ckey).
ii. Display Gain (sensitivity): magnifies the signal to
better fit the screen. This second gain or sensitivity
does not affect the amplification of the signal; it is
simply for display purposes.
 If the amplifier gain is set too high, there is a chance
that the amplifier will blocked or saturated. Thus, since
Evoked Potentials are very small magnitude signals,
you may wish to reject more signals than the set 99%
of the amplifier limit. Using A (Acceptance Level), the
user can choose the specific threshold for
acceptance/rejection.
 Choosing Sides
i. Left, Right, or No Side: The EP cursor placement
is allocated by "sweeps." That is, each collection of
sweeps is considered a "set" and cursors are
placed accordingly. This option allows for 4
Page 52
XLTEK NeuroMax
different sets of up to 4 traces each.

ii. Bilateral: Sets are defined by channel, not by
sweep. The first sweep of channel 1 and the
second sweep of channel 1 are considered a set
and the data table is filled according to this new set
definition. The bilateral selection (first two sweeps
one side and final two sweeps the other) allows for
up to eight sets of two traces each.
 There are ten customizable latency cursors, two
amplitude, six inter-peak-interval, distance, and
conduction velocity calculations are also available.
 Traces may be moved during acquisition by pressing
the Trace key, entering the trace number, and using
the Up/ Down arrows to adjust the trace.
 A single latency cursor is available to you while the
traces are acquiring. Press the Cursors key and then
use the Left/Right arrows.
5.1.3. SEP TESTS
1. Set stimulator rate between 3.1 and 7.9 Hz, but

Lower
not a multiple of 60 Hz, with duration of 0.2 -- 0.3 stimulus durations are
better tolerated but
msec. will preferentially
2. Place stimulator electrode over the nerve with excite motor neurons
over sensory neurons.
cathode (negative, black) proximal and cathode
(positive, red) distal.
3. To set stimulus Intensity, press the Start/Stop
Control key and use the stimulus controls to
increase the current level to approximately 3
times that at which the patient first felt the
shocks. Make sure that the correct muscles are
visibly twitching.
4. Press the Averager key to begin acquiring data.
Page 53
XLTEK NeuroMax
5. When a sufficient number of averages have Use the

Select key to toggle
been obtained, press the Averager key to through each trace
acquire the next set of traces. in succession. The
Left/Right arrows
6. Once acquisition of signals is complete, press move the red
vertical cursor
the Start/Stop Control key to end stimulation. across screen. The
Up/Down arrows
7. Press the Trace key and then use the toggle between the
Move/Superimpose features to overlay two/four channel
sets.
waveforms.
8. Press the Cursors key to mark signals.
9. To calculate a conduction velocity, press the
Distance key.
10. To exit the test, press the Test Menu key or the
Main Menu key.
5.1.4. SUGGESTED SEP PROTOCOLS

The tables below give you the suggested SEP
protocols and the protocols for specific location
acquisitions.
SUGGESTED SEP PROTOCOLS

Gain:
LFF: 20 Hz Avgs: 500
20uV/div
Sweep: Stim Rate: 5.3
HFF: 2 kHz
5ms/div Hz
NOTE: SEE CHAPTER 6 FOR THE AV STIM 1000 EP

OPERATIONS AND PROCEDURES.
5.1.4.1. MEDIAN C7 TO T1 / ULNAR C8 TO T1

NERVES
Channe Erb's contra

C3‟/4' (-) VS
l1 (+)
Channe Erb's contra
Erb's ipsi (-) VS
l2 (+)
Page 54
XLTEK NeuroMax
Channe
C3‟/4' (-) VS Fz (+)
l1
Channe
Cv5 (-) VS Fz (+)
l2
Channe
C3‟/C4‟ (-) VS Fz (+)
l1
Channe
Cv7 (-) VS Fz (+)
l2
Channe
Erb's (-) VS Fz (+)
l3
Channe
Elbow (-) VS Fz (+)
l4
SUGGESTED SEP PROTOCOLS

Gain:
LFF: 20 Hz Avgs: 500
20uV/div
Sweep: Stim Rate: 5.3
HFF: 2 kHz
5ms/div Hz
5.1.4.2. POSTERIOR TIBIAL NERVE L5 S1 S2
Channe
Cz (-) VS Fz (+)
l1
Channe Pop fos ipsi Pop fos contra
VS
l2 (-) (+)
5.1.4.3. COMMON PERONEAL NERVE S1 S2
Channe
Cz (-) VS Fz (+)
l1
Channe
Cv5 (-) VS L3 (+)
l2
Page 55
XLTEK NeuroMax
5.1.5. DERMATOMAL SEPS
DERMATOMAL SEP PROTOCOLS

LFF: 5 Hz Stim Rate: 3.3 Hz
Wrapping the Stim Duration: 0.2
stimulated digits in HFF: 500 Hz
ms
gauze prevents
stimulation spread to
adjacent 5.1.5.1. MEDIAN DERMATOMAL
dermatomes.
C6: Stimulate using ring electrodes places
over 1st or 2nd digit, cathode proximal, anode
2cm distal.
Channe
Cz (-) VS Fz (+)
l1
Channe
Cv5 (-) VS L3 (+)
l2
5.1.5.2. ULNAR DERMATOMAL
C8: Stimulate using ring electrodes places

over 5th digit, cathode proximal, anode 2cm
distal.
Channe
C3‟/4' (-) VS Fz (+)
l1
Channe
Erb's ipsi (-) VS Erb's contra
l2
5.1.5.3. POSTERIOR TIBIAL DERMATOMAL
L5: Stimulate medial side of the 1st metatarsal

phalangeal joint with a bar electrode, anode
distal.
Channe
Cz (-) VS Fz (+)
l1
S1: Stimulate lateral side of the 5th t metatarsal

phalangeal joint with a bar electrode, anode
distal.
Page 56
XLTEK NeuroMax
Channe
Cz (-) VS Fz (+)
l1
5.1.5.4. SURAL DERMATOMAL
S1: Stimulate under the lateral malleolus,

anode distal.
Channe
Cz (-) VS Fz (+)
l1
5.2. BLINK REFLEX

The Blink Reflex test as designed on the NeuroMax
is an easy to use protocol for the evaluation of the
R1 and R2 Compound Muscle Action Potentials
recorded from the orbicularis oculi muscle in
response to stimulation of either the supraorbital or
infraorbital branch of the trigeminal nerve. The Blink
Reflex test allows for the complete examination to
be performed on one test screen, with the flexibility
in setting up the default configuration to allow you to
run your own specific protocol.
To return to the 5.2.1. SETTING UP A BLINK REFLEX TEST

Other Tests Menu,
press the Test 1. Using the Select arrows, select Other Tests
The selections
Menu key. from the Main Menu and then press the Select for a Blink test are
limited by the nature
key to open the Other Tests Test Menu. of the test, thus the
2. In Section 1, choose the Facial setting using the NeuroMax notifies you
if the wrong nerve is
Select arrows and then press the Select key to selected.
continue.
3. In Section 2, choose Blink using the Select
arrows and then press the Select key to
continue.
4. In Section 3, the Bilateral side is defaulted.
Press the Select key to open the Blink Test
screen.
5.2.2. CONDUCTING BLINK REFLEX TESTS
Page 57
XLTEK NeuroMax
1. Press the Start/Stop Control key to stimulate. If you wish to

begin on the Right side
There are ten 2. Press the Select key to accept waveforms and (Left is the default),
customizable cursors.
when no waves have
Six inter-peak-interval move to the other side.
been acquired, press
calculations are also
3. Press the Cursors key to mark the signals. the Select key to
available.
switch sides.
4. Press the Test Menu key or the Main Menu key
to exit the test.
5.3. INCREMENTAL STIMULATION

The incremental stim test provides an indication of
the relative sizes of the motor units in a muscle, but
it can also be employed to estimate the number of
the functioning motor units. The muscles which are
most suitable for the technique are the EDB
(extensor digitorum brevis) and the median
innervated thenar muscles, but the technique has
also been used routinely for the hypothenar, plantar
and bicep muscles. In each stimulation, the active
recording electrode is a silver chloride strip which is
applied across the muscle belly at the level of the
innervation zone; a similar surface electrode is
positioned over, or beyond, the distal tendon and
serves as a reference. The stimulating electrodes
are placed over the motor nerve or, in some
instances, the motor point of the muscle. It is
important that the subject remain relaxed;
otherwise, traces will be rejected.
5.3.1. SETTING UP INCREMENTAL STIM

TESTS

key to open the Other Tests Test Menu.
To return to the Other 2. In Section 1, choose the Nerve/Muscle using the
Tests Menu, press the
Test Menu key.
Select arrows, and then press the Select key to
continue.
Page 58
XLTEK NeuroMax
3. In Section 2, choose Incr Stim using the Select

arrows, and then press the Select key to
continue.
4. In Section 3, choose either the Left or the Right
side, and then press the Select key to open the
Incremental Stim screen.
Page 59
XLTEK NeuroMax
5.3.2. CONDUCTING INCREMENTAL STIM

TESTS
1. Press the Start/Stop Control key to begin the

stimulation.
2. Increase the stimulation intensity until a small
response is seen.
3. Press the Select key to save response.
4. Increase the stimulation slowly and save
responses which are different from those on the
screen.
5. When ten or more waveforms have been The M is set up
acquired, stop the repetitive stimulation by to determine maximal
response – gain changes
pressing the Start/Stop Control key. to 5mV/div.
6. Press the M key on the keyboard.

7. Press the Start/Stop Control key to deliver
single stimuli.
8. Increase stimulus until response is maximal.
9. Press the Select key to save.
5.3.3. INCREMENTAL STIM TEST VALUES
After you have performed an Incremental Stim test,
you will see information similar to the following on your
screen:
1. Amplitude based estimate:24
2. Area based estimate:20
3. Estimated based on trace 14 and 15
The meanings of these values are as follows:
1. Amplitude based estimate:24 – Means that
using amplitude differences, the estimate of the
number of motor units is 24.
2. Area based estimate:20 – Means that using
area differences, the estimate for the number of
motor units is 20.
3. Estimated based on trace 14 and 15 – Means
that trace 14 (presumably the smallest one) and
15 (presumably the largest one) were used for
this estimate. In the case of amplitude, trace 14
Page 60
XLTEK NeuroMax
should be 24 times smaller than trace 15 if the

estimate is 24.
NOTE: Motor unit estimation should be used only by

clinicians who already have an understanding about
how it works
5.4. HEART RATE VARIABILITY (HRV)

The HRV test on the NeuroMax is designed to
graph the variability in hear rate over the course of a
60 second time trial. The parameters obtained at
the completion of a 60 second trial with the test are:
1. Maximum Heart rate (Max HR)
2. Minimum Heart Tate ( Min HR)
3. Mean Heart Rate ()Mean HR)
4. Standard Deviation of the Heart Rate (S.D. HR)
5.4.1. SETTING UP HRV STIMULATION

TESTS

key to open the Other Tests Menu.
2. In Section 1, choose the Nerve/Muscle using the
Select arrows and then press the Select key to
To return to the Other
Tests Menu, press the continue.
Test Menu key. 3. In Section 2, choose HRV using the Select
arrows and then press the Select key to
continue.
4. In Section 3, the Left side is automatically
selected by the NeuroMax. Press the Select key
to continue to the HRV test screen.
5.4.2. CONDUCTING HRV TESTS

The Heart Rate Variability test on the NeuroMax is
designed to graph the variability in heart rate over
Page 61
XLTEK NeuroMax
the course of four 60-second time intervals. At the

completion of each 60 second time trial, the
following parameters are calculated.
Page 62
XLTEK NeuroMax
HRV TEST PARAMETERS

Maximal Heart Rate Maximal R-R interval
Minimal Heart Rate Minimal R-R interval
Mean Heart Rate Mean R-R interval
Standard Deviation Heart Standard Deviation R-R
Rate interval
HRV Ratio (Max HR /
Min HR)
1. Set trigger to appropriate level using the Trigger

Press the
Up/Down Control arrows. Cursors key to modify
Press the Erase key to 2. Press the Start/Stop Control key to begin and the graph area where
delete all or a portion of the calculations are
the data. then press it again to end the acquisition of data. performed.
3. Press the Select key to save the response and

then move to next graph.
5.4.3. SYMPATHETIC SKIN RESPONSE
Involvement of the automatic nervous system
recording of the sympathetic skin response (SSR) is
one method of rapid evaluation of the autonomic
nervous system. The response is also known as
either the galvanic skin response or the
electrodermal response. SSR reflects the voltage
changes on the skin due to activation of either the
palmar or plantar sweat glands in response to a
variety of stimuli. In this case, electrical. The SSR is
a multi segmental somatosympathetic reflex arc
terminating with a final efferent pathway passing
through preganglionic and postganglionic
sudomotor fibers. Though intimidating to
conceptualize, it is straight forward to perform. The
patient must be relaxed and recumbent.
Normal recording parameter are not consistent
through the literature, We suggest that you use
variations of the below given parameters.
LFF 0.5 to 2.0 Hz,
HFF 500 to 5,000 Hz,
Gain 500 µV/div
Timebase 1 sec/div
Stimulate single irregular intervals with long

interstimulus intervals… between one (1) to three
(3) minutes to avoid habituation. Record from the
side contralateral to the site of stimulation.
Page 63
XLTEK NeuroMax
Hand: Reference electrode placed on the back of

the hand, active electrode placed on palm.
Stimulate the median nerve at a supramaximal level
0.1 msec. Cathode is proximal.
Foot: Reference electrode placed on dorsum, active

electrode placed on sole. Stimulate the tibial nerve
at a supramaximal level 0.1 msec. Cathode is
proximal.
Latencies are measured form the stimulus artifact to

the onset of the first negative OR positive peak.
Amplitude is measured peak to peak. A typical
recording session will consist of collecting up to ten
(10) responses from each nerve and recording the
mean value.
5.5. MULTI-CHANNEL EMG/IOM
1. Press the Stimulator key and then set stim Applies

to the NeuroMax
parameters, including duration, mode, maximum 1002/1004.
intensity
2. Press the Start/Stop Control key to begin the
acquisition. Press it again to end the acquisition.
3. Press the Space Bar to stimulate or to begin
repetitive mode.
4. Press the Settings key to make changes in
settings.
Page 64
XLTEK NeuroMax
5.6. MULTI-CHANNEL NERVE

CONDUCTIONS
Choose Other Test Menu
Choose or create Nerve Test Name
Choose 4-CH NCS
Choose side
Hit DEFAULT key for Test Defaults Editing Page
Customize your settings i.e. what channel is used,
what channel is on, test type, gains, timebases,
sites etc.
Hit SELECT and „S‟ to save settings
Example:
Median 2CH NCS
Active Ch 1 2
Channel 1 On On
CV Segments Segmental Total
LFF(Hz) 5.0 30
HFF(Hz) 2.0k 2.0k
Notch Filter Off On
Gain (uv/div) 5k 20
Lat1 take off take off
Lat2 neg phase peak
Amp bsln to peak peak to peak
Rec Site APB Index
Stim Site1 Wrist Wrist
Stim Site2 Elbow Elbow
Stim Site3 Axilla Axilla
Etc.
5.7. THE P300 TEST

Please Note: This test requires NeuroMax
1004/1002, code version 2.0 (available October ‟99)
or above and an AV Stim 1000, code version 5.0
(available October ‟99) or above.
5.7.1. GETTING STARTED
From the Main Menu, the P300 test can be

accessed from Other Tests (Option 3). Select a
Nerve or Muscle, then select P300 and a side. The
test will run identically for each side.
The P300 Test screen is similar to that of Evoked

Potentials. The gains (for all four channels) and
Page 65
XLTEK NeuroMax
timebase are shown on the top of the acquisition

box and the cursor, data and stimulator boxes are
located on the right of the screen.
The stimulator box shows the two different tones to

be presented to evoke the P300 response. Their
frequency and weighting can be changed using the
STIMULATOR hard key.
The data box contains the active cursors and once

placed on a waveform, their values. These cursors
can be set and labeled by editing the test‟s defaults.
For the first set of waveforms, cursor data will be
placed in Standard Set 1 or Target Set 1
(depending on whether the data was collected from
a target or standard response).
The command box shows the current tone that is

being presented to the patient as well as the
number of traces that are either included in the
averages or have been rejected. Different averages
are kept for target and standard responses.
If the NeuroMax is to keep track of patient input, the

command box also shows the number of times the
button was pressed during a standard tone (Press
on Stand.) and how many targets tones were
missed by the patient (Missed Targets).
Page 66
XLTEK NeuroMax
5.7.2. RUNNING THE TEST

Enter a patient name and data by pressing
PATIENT INFO while in the Test Menu or Main
Menu.
Enter the desired settings by pressing

STIMULATOR or use DEFAULT to set and save
these settings.
Press START/STOP to begin stimulating and

AVERAGER to begin acquiring data – the response
from the standard tone is placed above the
response from the target (oddball) tone.
Once a sufficient number of averages have been
obtained, press AVERAGER to begin acquiring next
set of traces.
Once acquisition of signals is completed, press

START/STOP to end stimulation.
Press CURSORS to mark signals.
Press TEST MENU or MAIN MENU to exit the test.
The patient response can be monitored using the

space bar or the external foot switch. The external
foot switch can be connected to the back of the
NeuroMax. The type of patient response is set in
the STIMULATOR menu under Patient Input.
5.7.3. HINTS AND FEATURES

There are two different gains available. Amplifier
gain is the actual input gain of the amplifiers. This
gain influences the rejection level of the signal.
Secondly, Display sensitivity, is used to further
scale the signal to better fit the screen. This second
gain or sensitivity does not affect the amplification of
the signal; it is simply for display purposes.
Traces may be moved during acquisition by

pressing TRACE, entering the trace number and
using the UP or DOWN arrow keys.
Page 67
XLTEK NeuroMax
A single latency cursor is available while the traces

are acquiring, by pressing CURSOR, and is moved
using LEFT or RIGHT arrow keys.
Two sets of traces can be acquired, for

repeatability. The response from the standard tone
always appears above the response from the target
tone. Separate averages for the standard and
target tones are maintained. Cursors can be
applied to each group of traces – any combination
of 10 latencies, 2 amplitudes and 6 inter-peak-
intervals up to a maximum of 14. These can be
turned on or off and labeled while editing defaults.
The typical response mechanism to a target tone is

a finger tap or button press. The NeuroMax can
monitor the patient input from a target tone from a
button press. Typically, for maximal P300
amplitude, the patient must acknowledge that they
have heard a target or odd tone. The patient can
either enter their response via a press of the space
bar or using the foot switch.
The NeuroMax keeps track of how many times a

response was entered incorrectly (i.e. the space bar
was pressed during a standard tone) and how many
target tones were missed. These numbers appear
in the command box. If a target tone is presented
and an acknowledgement is not made, the
response is not included in either the standard or
the target average.
The current tone being presented is displayed in the

command box. The NeuroMax ensures that a
standard tone is always played first and ensures
that a target tone is always followed by a standard
tone. The type of tone to be played is determined
randomly, based on the weightings assigned to
each tone in the STIMULATOR menu.
The volume of the tones cannot be changed while

averaging. To ensure that the volume is
appropriate, press START/STOP until the tones can
be heard. Use the hotkey ‘R’ to display the raw
traces. Once satisfied, acquisition can begin by
pressing AVERAGER.
Page 68
XLTEK NeuroMax
To increase the timebase, use the right and left

arrows. Because the P300 event usually occurs
300 msec after the stimulus is presented, a
timebase of 50 msec is recommended. The
timebase cannot be changed if the stim in ON or if
there are traces on the screen. Press ‘R’ to erase
the raw traces, ERASE to erase the averaged
traces and START/STOP to turn off the stimulator.
The timebase is limited by the inter-stim-interval so
that acquisition ends before the next tone is
presented.
Some recommended settings include:

LFF: 0.5 Hz
HFF: 30 Hz
Display Gain: 5 uV/div
Timebase: 50 ms
Cursors: N1, N2, P2 and P3
Inter-Stim-Interval: 2 seconds
Standard Frequency: 1000 Hz at 80%
Target Frequency: 2000 Hz at 20%
5.7.4. EXPLANATION OF OPTIONS

STIMULATOR – Number of Stimuli: The number of
different tones presented to the patient. If three
tones are being presented, the response from Non-
Target tones is not displayed or included in any
averages.
STIMULATOR – Patient Input: Indicates if the

NeuroMax will keep of patient responses. If so, the
patient can acknowledge a target tone with a tap of
the space bar or the press of the external foot
switch.
STIMULATOR – Standard, Target and Non-Target

Frequency: Use the right and left arrows to scroll
between the available frequencies (250, 500, 1000,
2000, 4000 Hz). Then choose the percentage that
this tone should be presented. These percentages
must total to 100%.
STIMULATOR – Rise/Fall Time: The number of

cycles to be used as the ramp up to the tone.
Page 69
XLTEK NeuroMax
STIMULATOR – Duration: The length of the tone,

not including the rise/fall time.
STIMULATOR – Inter Stimulus Interval: The time

between the presentation of tones. This interval
must be long enough such that the tone can be
presented cleanly (without cut off) and that the
entire trace can be displayed before the
presentation of a new tone.
Page 70
XLTEK NeuroMax
5.8. THE ERG

(ELECTRORETINOGRAM) TEST
5.8.1. ABOUT THE ERG TEST
The electroretinogram (ERG) measures the mass

retinal response to a stimulus of light using a
corneal electrode and neutral electrodes placed on
the skin around the eye. The corneal electrode is
placed gently behind the lower eyelid and contacts
the cornea. The patient is kept comfortable with
topical anesthesia, or in infants, general anesthesia
may be used. A flash of light is shown to the patient
and the electrodes record the retinal potentials
which develop as a response to the flash. This
diagnostic procedure may be useful in
distinguishing between a variety of retinal disorders
such as cone dystrophy and retinitis pigmentosa.
5.8.2. CONFIGURING THE ERG PROTOCOL
The ERG protocol must be configured by the user.
1. Go to Nerve >Conduction from the main menu.
2. Go to a blank field. Press Backspace and C or
the Default key.
3. Type ERG and press Select, as advised.
4. Select the ERG test, then choose Sensory and
Left/Right or both and press Select.
5. The Screen opens.
6. Press the Default key and choose the settings you
require. (For example, a low frequency of 1 and a
high frequency of 250; a time base of 10 ms /div;
and a gain of 20 uv /div.)
7. Select External Stimulator from this panel and
trigger out or in, as desired.
8. Choose Active high, Ground on, 60 Hz filter on.
NOTE: Other things, such as the intensity of the flash,

are controlled on the photic stimulator you have.
Page 71
XLTEK NeuroMax
The above settings will result in the recording of good

ERG. You will be able to record photic, scotopic and
flicker fusion with suitable selections.
5.9. THE EOG (ELECTRO-

OCULOGRAM) TEST
5.9.1. ABOUT THE EOG TEST
The electro-oculogram records eye movements
because of a voltage difference between the cornea
and retina. As the eye moves, the vector of this electric
field changes with respect to a reference electrode. At
least two (2) biopotential channels are required when
recording eye movements to assist in distinguishing
eye movement potentials from other signal artifacts.
5.9.2. CONFIGURING THE E0G PROTOCOL

The EOG protocol can be configured in a manner
similar to the ERG protocol discussed previously.
1. Go to Nerve > Conduction from the main menu.
2. Go to a blank field. Press Backspace and C or
the Default key.
3. Type EOG and press Select, as advised.
4. Select the EOG test, then choose Sensory and
Left/Right or both and press Select.
5. The Screen opens.
6. Press the Default key and choose a low frequency
of 0.1 and high frequency of 1000; a time base of
500 ms /div; and a gain of 500 uv /div.
Pre-adapted signal is acquired from each eye, then
dark-adapted, and lastly light-adapted. The Arden
index is calculated by dividing amplitude of light rise
signal by dark-adapted eye signal and multiplying that
by 100.
Page 72
XLTEK NeuroMax
6. AV STIM 1000
The AV Stim is used with Evoked Potentials and
operates with both the NeuroMax 1002 and the
NeuroMax 1004, and with subsequent operating
systems.
6.1. AV STIM 1000 FRONT PANEL
The red
stimulus indicator
The green power
blinks on when the
indicator lights up
NeuroMax powers up
when AVSTIM
and flashes at the set
1000 is powered on.
stimulus rate.
6.2. AV STIM 1000 REAR PANEL
NeuroMax
Audio Out
Connect to NeuroMax
LEDGoggles
VGA
Update Port
Audio Out: Plug in the calibrated headphones

supplied with your AV STIM 1000. CAUTION: Before using
the headphones and
goggles, you should
Warning: Only the XLTEK headphones (part
inspect themfor any
number 102610) have been approved for use with physical damage to the
your AV Stim. Patient isolation in accordance with casings. If there are any
EN60601-1 is dependent on the approved parts. signs of cracking,
warping, or other physical
LED Goggles: LED goggles generate difficult to damage, DONOT use the
reproduce visual evoked potentials due to the high equipment. Notify an
XLTEK Customer Service
intensity of the flash. We suggest filling the inside Representative
of the goggles with cotton balls and asking the immediately.
patient to have their eyes closed.
Page 73
XLTEK NeuroMax
Warning: Only the XLTEK LED goggles (part

number 101487) have been approved for use with
your AV Stim. Patient isolation in accordance with
EN60601-1 is dependent on the approved parts.
Printer: An optically isolated printer port that is

available only to older NeuroMax users. When
using the Windows based NeuroMax this is not
supported.
NeuroMax: The connector port to which the

NeuroMax is attached with the supplied cable.
VGA: Standard D-sub video monitor connector. The

recommended video monitor is a hospital grade
VGA or SVGA monitor.
Warning: Only equipment approved to IEC950, EN

60601-1 or a similar safety standard may be
connected to the "Upgrade Port" and "VGA" ports
on the AV Stim 1000. The final system must be
configured to meet the requirements for safety of
medical systems prescribed by EN 60601-1.
6.3. CONNECTING THE AV STIM 1000

1. To perform either an auditory or visual evoked
potential, connect the AV STIM 1000 to the
NeuroMax using the supplied connector cable.
2. Switch the NeuroMax Off and then insert the
male 26-pin connector of the connector cable
into the AVStim port at the rear of the
NeuroMax.
3. Insert the other end, also a male 26-pin
connector, into the AV STIM 1000 NeuroMax
port.
The red Stimulus
light indicates that 4. Turn the NeuroMax On and check the AV STIM
the AVSTIM is
1000 to confirm that the green light comes on,
correctly configured
and initialized. followed by a brief flash from the red Stimulus
light.
Page 74
XLTEK NeuroMax
6.4. WARNINGS AND CAUTIONS

The following Warnings and Cautions are marked
with a and must be followed very closely to
ensure the safety of both the patient and the user of
the AV Stim and the NeuroMax. It is therefore
important to read and observe ALL of the Warnings
and Cautions before attempting to use the AV Stim
and the NeuroMax. If there is any malfunction or
perceived malfunction of the system, please call an
authorized XLTEK service representative
immediately at 1-800-303-0306. An authorized
XLTEK service representative must only conduct all
internal system checks and/or service.
6.4.1. WARNINGS
Warnings MUST be followed when using the
equipment. Warnings apply to conditions, which can
injure the patient and/or the operator.
WARNING: Exposure to excessive

sound can cause temporary and even
permanent hearing loss.
WARNING: Long term exposure to

excessive light can cause temporary and
even permanent changes in visual acuity.
WARNING: Patient electrical isolation

(BS EN 60601-1) is ensured when all
peripherals (Headphones, Printer,
Goggles, Monitor) attached to the Audio
Visual Stimulator are XLTEK approved.
The final system configuration must meet
the requirements of EN 60601-1 for
safety of medical systems.
WARNING: Use of the AV STIM 1000

is not compatible with defibrillators or
electrocautery devices.
6.4.2. CAUTIONS
Page 75
XLTEK NeuroMax
Cautions must be noted when using the equipment.

Cautions apply to conditions which may damage the
NeuroMax and other equipment.
CAUTION: If you choose to attach a

VGA display other than the model
supplied by XLTEK, it MUST either meet
IEC 601-1 or the leakage current
requirements for your jurisdiction.
CAUTION: The AV STIM 1000 provides

signals to the headphones, the LED
goggles, and to the video stimulator.
Otherwise, signals are provided by the
NeuroMax.
6.5. CALIBRATION AND

MAINTENANCE
The AV STIM 1000 requires minimal maintenance.
The supplied headphones are factory calibrated to
the specific NeuroMax you are using. If for any
reason, the headphones require replacement or re-
calibration, both the headphones and the AV STIM
1000 unit must be returned to XLTEK.
Please observe the following conditions:
 For the sound level pressure reading to be valid,

only XLTEK approved headphones are to be used.
 The AV STIM 1000 does not at present support
NTSC video monitors.
 The visual stimulator must be calibrated by the user.
This involves dedicating a monitor for the purpose of
presenting the visual stimulus, collecting normal
values, and then fixing the brightness, contrast and
distance to the patient. Do not alter these values.
 The interior surface of the LED goggles should be
inspected before and after an examination, and
cleaned with a soft cloth. Remove any oil or dust
from both the interior and exterior surfaces.
Page 76
XLTEK NeuroMax
Periodically check to be certain that all LEDs are

functioning.
6.6. SUGGESTED AEP PROTOCOLS

SUGGESTED AEP PROTOCOLS
The use of a
LFF: 150 Pulse Frequency: jumper cable is
Gain: 2uV/div
Hz 11.1 Hz recommended to
HFF: 2.0 Sweep: connect the
kHz 1ms/div reference leads.
Also, use electrode
Channe to Fz as a ground.
A1 (-) VS Cz (+)
l1
Channe
A2 (-) VS Cz (+)
l2
6.6.1. AEP IMPEDANCE CHECK
1. Press the I (Impedance) key while testing to

check impedance levels.
2. Press the Select key to return to test screen.
6.7. SUGGESTED VEP PROTOCOLS

SUGGESTED VEP PROTOCOLS
The use of a
LFF: 0.5 Gain: Pulse Frequency: jumper cable is
Hz 5uV/Div 1.1 Hz recommended to
connect the reference
HFF: 100 Sweep: leads. Also, use an
kHz 25ms/div electrode to Fz as a
One Channel ground.
Channe
Oz (-) VS Cz (+)
l1
Two Channel
Channe
O1 (-) VS Cz (+)
l1
Channe
O2 (-) VS Cz (+)
l2
Page 77
XLTEK NeuroMax
6.7.1. VEP IMPEDANCE CHECK
1. Press the I (Impedance) key while testing to

Impedances of
check impedance levels. about 5 kOhms are
2. Set impedance levels. recommended for clear
results.
3. Press the Select key to return to test screen.
6.8. ACQUIRING A FULLFIELD VEP

RESPONSE
The setup for the Fullfield VEP Response is
completed in the Choose Side section of the Other
Tests test screen.
1. Choose the eye to test. To begin with the left

If you are
eye, choose the Left side and then press the doing a Bilateral test,
Select key to continue. start with the left eye
and follow the steps.
2. Press the Stimulator Control key and then set
the Stimulator to Left Field Stimulus and/or Right
Field Stimulus.
In a unilateral study, 3. Have the test subject cover the right eye and
4 sets of 2 channels fixate towards the center of the checkerboard
can be collected in
this manner. field with the left eye.
4. Press the Start/Stop Control key and begin the
acquisition.
5. Press the Averager key to begin averaging.
6. Once a set is completed, press the Averager
key again to collect the next set. If you are
doing a Bilateral test
7. To test the Right side, press the Test Menu key, (collecting waveforms
on the same menu
select the Right side in the Choose Side section screen), switch eyes
of the Test Screen, and then press the Select and repeat steps 3-6.
key to continue.
8. Cover left eye and repeat steps 2-6.
Page 78
XLTEK NeuroMax
6.9. ACQUIRING A HEMIFIELD VEP

RESPONSE
The setup for the Hemifield VEP Response is
completed in the Choose Side section of the Other
Tests test screen.
1. In the Choose Side section, select Bilateral and

then press the Select key to continue.
2. Press the Stimulator key and set the Stimulator
to Left Field Stimulus and Right Field Nothing.
Montage for Right eye (Left covered)
Channe
Oz (-) VS Fpz (+)
l1
Channe 10cm lateral to
Use these tables to VS Fpz (+)
set your Montage l2 O1 (-)
levels.
Montage for Left eye (Right covered)
Channe
Oz (-) VS Fpz (+)
l1
Channe 10cm lateral to
VS Fpz (+)
l2 O2 (-)
3. Have subject cover the Right eye and fixate

towards the center of the checkerboard field.
To switch to
4. Press the Start/Stop Control key and begin the other side, cover
the left eye, set the
acquisition. Stimulator to Right
Field Stimulus and
5. Press the Averager key to begin averaging. Left Field Nothing.
6. Once a set is completed, press the Averager
key again to collect the next set.
Page 79
XLTEK NeuroMax
7. SETTING THE DEFAULTS

The setting on all of your tests can be designed to
suit your particular needs. Thus whenever you
activate the NeuroMax to do a particular test, your
specific settings will already be chosen. This
automatic setting is called a "default setting," and
the NeuroMax comes to you with a full complement
of default settings designed to meet the greatest
variety of requirements.
7.1. TEST MENU PARAMETERS

On any given test menu you can change/add the
name of a nerve (Nerve Conductions Test Menu),
muscle (Electromyography Test Menu), or protocol
(Other Tests Menu).
CAUTION: This will permanently change

the Test Menu.
1. From the NeuroMax Main Menu screen, use the

Select arrows to choose the Test Menu and then
press the Select key to open the Test Menu.
2. Use the Left/Right arrows to place the yellow
highlight over the position to be changed.
The Default key is
located at the bottom 3. Press the Default key to open the Default
left of the keyboard. You can also
Settings box. activate the Default
setting box by pressing
4. Using the keypad, enter the name of the new
Backspace + C.
nerve/ muscle/ protocol.
5. Press the Select key to exit.
Page 80
XLTEK NeuroMax
7.1.1. CREATING AN
ELECTROMYOGRAPHY SUITE
You can set the default parameters to create a
personalized EMG suite that fits your specifications.
1. From the NeuroMax Main Menu, use the Select

arrows to choose Electromyography and then
highlight over the Suite name you wish to edit.
3. Press the Default key. You can also
The Default key is
located at the bottom activate the Default
4. Using the keypad, enter the name of the Suite.
left of the keyboard. setting box by pressing
5. Press the Select key to save the name of your Backspace + C.
Suite.
highlight over the next muscle you wish to add to
the suite and then press the Select key.
Continue until all muscles have been added.
7. Press the Test Menu key twice to save and exit.
7.2. EDITING TEST DEFAULTS

Many of the test routines and features of the
NeuroMax, including test protocols and other
functions, are customizable to allow automation of
many routines. The NeuroMax1002/1004 is
equipped with factory default settings for many
tests, and these are a good general guide for many
of the tests and reporting features. However, you
may wish to change these settings. If the changes
desired are temporary, then the changes should be
made using the various keys (Settings,
Stimulator). However, if you want the new settings
to be automatically included each time a particular
test is selected, then the defaults should be
changed.
Page 81
XLTEK NeuroMax
1. From the NeuroMax Main Menu screen, use the

Select arrows to choose the test menu and then
2. Using the Select arrows, choose the test you
wish change and then press the Select key
twice to open the Active Test Screen.
3. Press the Default key.
You can also
4. Use the Select arrows to choose the settings to activate the Default
The Default key is setting box by pressing
located at the bottom
change and then use the keyboard to enter the Space Bar + C.
left of the keyboard. new values. These values become the new
default settings.
5. Press the Select key to open the Save and Exit
dialog box.
Press S to save, or Dto discard changes.

To restore factory defaults, press R.
To continue editing defaults, press E.
Figure 7.1: Save and Exit Dialog Box

6. Select one of the options and continue. Note that
you can always return to the factory default
settings that came with the NeuroMax.
Page 82
XLTEK NeuroMax
8. ADMINISTRATIVE FUNCTIONS
The NeuroMax Administrative Functions are
designed to help you customize the NeuroMax and
to manage the information acquired by the tests.
This chapter shows you how to customize reports,

store data, and transfer files.
8.1. ADMINISTRATIVE FUNCTIONS

The Administrative Functions menu allows you to
customize the reports, functions, and memory of the
system. Data entered on these menus makes
permanent changes to the system. The following
chart lists the administrative functions.
REPORT FUNCTIONS
Patient Recall, print, and edit stored
Directory patient files
Memory Delete files and erase
Management memory
Batch Print Print all non-printed reports
System Set global options including
Options date, time, units of measure,
printer type, artifact rejection,
external stimulator, and more
Edit Report Edit macros, select fields
Format included in the report, and
report layout
Edit Site Name Edit the available default
List stimulation sites
Edit EMG Edit available notes for
Notepad scoring EMG
Edit Patient Edit the field definitions for
Info. Fields the Patient Info screen
Page 83
XLTEK NeuroMax
8.1.1. PATIENT DIRECTORY

The patient directory may be quite extensive
because the NeuroMax has the ability to store many
files.
Figure 8.1: Patient Directory
It outlines which patients are saved on the system,

the status of those patients (Printed, Not Printed,
Transferred), the date the patients were saved and
gives the user certain functions.
PATIENT DIRECTORY FUNCTIONS

Patient Recall a patient to add to the
Callback current file or to begin a new
study.
Test View list of test files, along
Directory with the date and time they
were performed. Within this
directory, tests can be
recalled and then edited or
deleted.
Print Report Print the highlighted patient
report. Make sure
View Report View the highlighted patient you select the
report. patient file before
Delete Patient Delete Patient and tests activating the
Function options.
Edit Patient Edit the selected patient
Info. information.
Page 84
XLTEK NeuroMax
Future
Expansion
Print All Test Print all performed test
Screens waveforms in condensed
format.
Print Letter Print the history and
interpretation in a letter
format with the referring
doctor‟s name.
Save File to Moves highlighted files to
USB USB device. See section
8.1.2. for details.
Exit Directory Exit to Administration Menu.
8.1.2. MEMORY MANAGEMENT

The Memory Management Option shows you the
available memory and how to clear the memory to
allow for more patient files. You should monitor the
memory on the NeuroMax regularly and archive the
reports you wish to store.
Figure 8.2: Memory Management
IMPORTANT: Deleting patient files from the

NeuroMax moves the information from live file
memory, which is shown as a yellow bar, to deleted
file memory, which is shown as a red bar. Both
types of file memory will increase to fill the total
maximum amount of memory available.
Page 85
XLTEK NeuroMax
To free up more memory on the NeuroMax, you

must archive/backup all deleted files by: 1. Saving
the files to another computer via USB or 2. By
printing hard copies of the files.
Once you have backed up all the files use these

steps to permanently delete the deleted files and
free more memory. TAKE NOTE THAT THE
PERMANENT DELETION OF FILES PERTAINS
TO ALL DELETED FILES OR NONE OF THE
DELETED FILES.
1. Start in the Main Menu.

2. Select Administrative Functions #4.
3. Select Memory Management #2.
4. Select Delete All Files #2.
8.1.3. BATCH PRINT

Batch Print collects and prints all the patient files
that have not yet been printed.
8.1.4. SYSTEM OPTIONS

Using the System Options allows you to set a
variety of standards for display formats and printed
reports. You can also enhance the NeuroMax's
performance.
Figure 8.3: System Options
Page 86
XLTEK NeuroMax
8.1.5. EDIT REPORT FORMAT

You can design the report formats to fit your
particular requirements. The NeuroMax provides
five areas to customize.
i) Edit Report Header: Places name, address,

and other information on all reports.
ii) Edit Interpretation Macros: Provides titles for
automatic notes use in history and
interpretation fields.
iii) Turn on/off Report Fields: Selects the fields
to be printed in the tables of the report.
iv) Change Report Layout: Edits the report
format to sort by time, test name, and Muscle
or nerve.
v) Return To Administration Menu: Returns
you to the main administration menu.
8.1.6. EDIT SITE NAME LIST

You can change or add the default stimulation site
names by selecting an existing name and then
deleting and entering a new name. The new name
cannot be more than
12 characters long.
8.1.7. EDIT EMG NOTEPAD

You can edit the standard Notes format available
when acquiring EMGs to reflect your requirements.
8.1.8. EDIT PATIENT INFORMATION FIELDS

You can customize the fields you would like to
appear on the patient information section of the
reports.
8.1.9. CHANGING THE DATE ON STORED

DATA
On pre-stored files:
1. Turn On the NeuroMax, or be certain that there is
currently no selected patient.
2. From the Main Menu, select Administration
Functions then Patient Directory
Page 87
XLTEK NeuroMax
3. Choose the Patient Choose 0. Patient Callback

into Current Study
4. Choose Main Menu followed by Administration
Functions followed by SYSTEMS OPTIONS
5. You are now going to change the date to suite your
needs.
6. Choose Edit Date or Edit Time and set to the
required needs.
7. Exit from this screen, go to Main Menu and press
Patient info. And choose Edit Current Patient.
8. You must now rename the patient. I suggest that
you simply add aaa to the beginning of the patient
name.
9. Press Patient Info. When done.
10. Patient is now stored under the new date.
11. You must now press Patient Info. again and
remove the aaa from the patient name. Press
Patient info. To exit this screen
12. Repeat steps 4 to 6 to change the date back to the
current date.
13. You are now complete.
8.2. MANAGING THE REPORTS You can decide

how you want to
Once you have transferred the reports from the manage the files,
NeuroMax to your PC, you can view them, print whether you want to use
them, edit them, and/or discard them. Transferring themor periodically
delete them.
the files by cable also changes their format into Rich
Text Format (RTF), which can be read by a variety
of word processing programs.
8.2.1. RICH TEXT FILES (RTF)

Rich Text Format (RTF)
Downloading files to a USB device will automatically files can be imported
create files with an RTF file extension in the default into many different
directory. Windows applications
such as Word.
Page 88
Xltek NeuroMax
8.3. EXTENDED WARRANTY SERVICES INFORMATION

An extended warranty can be purchased prior to or following the expiration of
your NATUS original warranty. For further information, contact XLTEK‟s
Customer Support at 1-800-303-0306 or
[email protected].
Page 89
Xltek NeuroMax
9. APPENDIX 1: IN-SERVICE CHECKLIST

NeuroMax In-Service Checklist
Name/Institution:
Tel: Fax: Email:
Additional Contacts: Name Position
Basic Functions
Connections for NeuroMax: Keyboard Layout:
USB Printer Function Hard Keys
Headbox Menu Hard Keys
Stim Probe Select Switch
Accessories Arrow Keys
USB Mass Storage Trigger Arrows
Foot Switch Stimulus Intensity
AV STIM Functions: Opening a Patient File
External Trig Electrode Impedance Testing
Hot Keys
Power Supply of NeuroMax:
AVStim:
Nerve Conduction Functions

Assigning Waveforms Stimulator Creating Protocols for:
Full-Screen Acquisition Notes SNC
Trace Erase MNC
Settings Average F-Wave
Cursors Exponential Decay ("X") Rep Stim
Distance H-Reflex
Electromyography
Basic Functions: Advanced Functions: Creating Editing:
Recording (Start/Stop) Review Defaults
Settings: (Gain/Timebase) Turns and Amplitudes Triggered Defaults
Audio Adjustments Motor Unit Analysis (1,2) EMG Suites
Notepad Free Run to Triggered Muscles
Suites (key function)
Programs:
Free Run
Triggered
Page 90
Xltek NeuroMax
Administrative Functions
Patient Directory: Memory Management:
Search Utility
Patient Callback Patient Directory
Test Directory Delete All Files
Print Report Delete All Printed files
View Report
Delete File System Options:
Edit Patient Info 1) Report Format
Transfer to USB -Report Header -Report Fields
Print Test Screens -Interpretation Macros -Report Layout
2) Site Name List
Batch Print: 3) EMG Notepad
4) Patient Information Fields
Dual Channel Tests

Functions: EP's - Stimulating BLINKS - Stimulating
Averaging Saving Waveforms
Saving Waveforms Cursors
Cursors HRV
Creating Protocols for - EP's Multi-Channel EMG/IOM
Multi-Channel NCS
Report Menu
While in an active patient file, press REPORT. The following functions should now be available:
View Report Print Report
Edit Report (host directory) Print Report and Waveforms
Interpretation Save Current Patient to USB
Accessories
Main Contact (for ordering Consumable items): Please indicate style of Needle currently used:
Name: Disposable Monopolar
Phone: Disposable Concentric
Disposable Injectible Monopolar
Please indicate the length and gauge of the needles used:
Please indicate the number of EMG's performed monthly:
Please indicate if you are using: Please indicate your current Accessories Supplier:
Disposable Electrodes
or Reusable Electrodes
for Nerve Conduction Studies
Are you currently receiving Preferential Pricing for a Needle Contract? Yes No
?? - Would you be interested in hearing how Accessories are able to enhance the quality of
your studies, as well as save you time and money? Yes No
Page 91
Xltek NeuroMax
XLTEK University
?? - Would you be interested in hearing how XLTEK University is able to give you one-on one, on-site
training, that can help you in the areas of, but not limited to:
equipment use, basic and advanced clinical training, and insight on clinical correlation?
Yes No
I am interested in: Nerve Conduction Studies/EMG

Evoked Potentials
Both
COMMENTS
Please Confirm
Date Completed:
Client Name: Sales Rep:

(please print) (please print)
Signature: Signature:
Page 92
Xltek NeuroMax
10. APPENDIX 2:
TROUBLESHOOTING
Symptom Cause Solution
No visual display or audio alarms at Power switch not turned on. Plug in power cord.
power-up. Turn power switch on.
Electrode impedance is too high. Electrode dislodged from patient, but not Insert dislodged electrode; tape down in place.
> 10 KΩ for subdermal electrodes. completely out.
> 25 KΩ for Prass paired electrodes. High resistance in electrode. Remove and replace with new electrode.
> 05 KΩ for EMG tube. Electrode pin not firmly inserted into patient Check connection at Patient Interface box.
> 40 KΩ for hookwire electrode. interface.
Electrode impedance ≤ 0.1 KΩ Positive and negative electrodes touching below Remove and relocate electrodes.
surface of skin.
Extremely low impedance, particularly in EMG Use “tap test” near electrodes to evoke EMG or artifact
tubes. (increase threshold, decrease volume for test). If activity
is noted on channel in question, proceed.
Electrode reading is: Electrode laying on skin surface. Re-insert electrode in question.
(+ or -) Off Electrode placement insecure.
or Dirty electrode tip. Remove and replace electrode in question.
Δ==== Electrode cable is broken.
Electrode pin disconnected from patient interface. Check connection to Patient Interface box.
Electrode difference is greater than Dirty electrode. Remove and replace electrode for appropriate channel
2KΩ (Subdermal electrodes) or with highest impedance reading first.
10KΩ (Prass Paired electrodes). Mismatched pair. Remove and replace electrode in question.
Unequal placement.
Interference on anesthesia equipment Measuring current on NIM® EMG Electrodes. Try an alternate EKG Lead set.
(EKG Monitor).
Electrode Check (Electrode Screen selected). Deselect Electrode Screen.
Muting function active. See Excessive Muting (Symptom Column).
With Stimulator active. Turn the NIM® Stimulator to 0.0 mA when not needed.
Incrementing Probe will not adjust Loose connector. Check connector is properly aligned and fully seated (See
stimulation. System Set Up / Patient Interface Set Up).
- -
Stimulus keeps changing (run away). Bad Incrementing Probe. Replace Incrementing Probe or disconnect STIM
CONTROL connector and manually adjust stimulus at
touch screen.
Electrosurgical interference. Muting Detector Probe not connected. Check Muting Detector Probe connections.
Muting Detector Probe input insufficient. Loop the unit cable through muting detector.
Electrosurgical grounding inadequate. Check electrosurgical grounding pad on patient.
Source of interference unidentified. Identify source of interference; then eliminate or separate
NIM 3.0 system or Patient Interface cable too Maintain separation between electrosurgical cable
close to electrosurgical unit or its cables.
For less coupling, coil up the Muting Detector Probe next
Excessive Muting. Unit receiving excessive signal into the Muting Disconnect the muting detector completely.
Detector Probe or electrode leads.
Rhythmic Artifact. Pacemakers – Pace Pulse. Relocate electrode ground and stimulus return to patients
shoulder (Acromion).
Inadequate muting. Signal from electrosurgical unit inadequate to Loop the electrosurgical unit cable and clip the muting
cause muting. detector over the doubled cable.
No response to direct stimulation. Inadequate stimulus intensity. Increase stimulus intensity.
Paralyzing anesthetic in use. Eliminate paralyzing anesthetic.
White Stimulation (+) electrode has fallen out or Check that Stimulus Measure is approximately the same
is not connected. value as the Stimulus setting. Re insert electrode in
-
question.
Probe (electrode) not connected. Check stimulator anode (+) and cathode (-) connections.
Patient safety fuse blown. Check fuse in STIM 1 (EMG) Patient Interface Replace if
STIM 1 (EMG) Patient Interface fuse REF necessary.
8253075.
Not holding probe on nerve long enough. Hold probe tip to nerve for at least 1 second.
Nerve not contacted. Check stimulator tip for obstruction. Replace if
necessary. Check location of stimulation.
Volume control too low. Check and correct all settings volume, event threshold,
Event threshold set too high. stimulus intensity.
Excessive current shunting in surgical field. Remove fluids from surgical stimulating area.
No electrodes in innervated muscle tissue. Nerve Place channel electrodes in muscle to be monitored.
not stumbled. Check EMG tube placement if applicable.
Page 93
Xltek NeuroMax
Unexpected responses when not Unexplained continuous “train” EMG response. Identify and eliminate possible source of “train”
directly stimulating nerve. stimulation:
Cold irrigation.
Laser heat.
Retraction on nerve or muscles being recorded.
Patient waking from anesthesia.
Nerve drying.
Ultrasonic aspirator.
Nerve or monitoring area being stimulated or Identify and eliminate source of inadvertent
manipulated by thermal or mechanical means. manipulation.
Metal-to-metal discharge artifact. Determine response type from waveform pattern on
50 ms screen.
Intertwined recording electrode and stimulator Disentangle recording electrode and stimulator cables.
wires.
Inadvertent manipulation of electrode wires, Check area near recording electrodes for excessive
Patient Interface cable, or recording area on stretching from tape, drapes, etc.
patient.
Electrical interference from other equipment. Check for intermittent stimulation from anesthesiologist
(i.e., hand-held electrical stimulator).
Move NIM 3.0 system away from source of interference.
Make sure Patient Interface cable and electrode wires do
not cross other electrical equipment or cables.
Page 94
Xltek NeuroMax
10.1. SOFTWARE
The following sections show you how to verify the software version on your
machine, how to update your software, and how to install NeuroMax Loader.
10.1.1. CHECKING SOFTWARE VERSION ON NEUROMAX

1. Turn on the power to the NeuroMax.
2. From the Main Menu screen, press ESC and the V key on the keyboard.
3. The version number appears in the bottom left corner of the screen.
-
10.1.2. UPDATING SOFTWARE

Obtain the newest version of software by contacting Technical Support at 1-
800 303 0306 or [email protected]
- -
NOTE: ANY CUSTOMIZATION OF TEST DEFAULTS AND REPORT FORMAT WILL NOT
BE AFFECTED.
10.2. NERVE CONDUCTIONS

This section gives you the basic steps for creating a Nerve Conduction Study
(NCS), how to edit it, and how to set up a stimulus site.
10.3. ELECTROMYOGRAPHY
This section gives you the basic steps for creating an electromyography suite and
how to use it.
Page 95
Xltek NeuroMax
10.4. ADMINISTRATIVE FUNCTIONS

The administrative functions are designed to help you prepare the NeuroMax for
your specific circumstances and to manage the data you have acquired once
the testing is complete.
10.4.1. EDITING STUDIES
10.4.1.1. EDITING A PATIENT STUDY WHILE IN ACTIVE PATIENT FILE
1. From Main Menu screen, press the Report key.

2. In the Function column, choose Edit Report.
10.4.1.2. EDITING A PATIENT STUDY NOT IN ACTIVE PATIENT FILE
1. From Main Menu screen, select Administrative Functions and then select
Patient Directory.
2. Using the Select arrows, choose Patient Directory, highlight patient name,
and then select Test Directory in the Functions column.
3. Choose the test to edit and press the Select key, choose Recall and Edit
File.
10.4.2. INTERPRETATION MACROS
10.4.2.1. CREATING A MACRO
1. From the Main Menu screen, select Administrative Functions and then
select Edit Report Format.
2. From the Edit Report Format Menu, select Edit Interpretation Macros to
view the 30 titles that can be edited. Each title represents one interpretation
macro.
3. To edit a title, choose it using the Select arrows. A red cursor appears in the
lower box. Next use the keyboard to enter your prepared macro into the
highlighted position and then press the Select key to enter the macro.
4. When finished, press the Select key once to move onto the next macro.
5. To exit from the Edit Interpretation Macros screen, highlight EXIT from
Interpretation Macros and press the Select key.
Page 96
Xltek NeuroMax
10.4.2.2. USING A PRE-DEFINED MACRO IN A REPORT
1. From the Main Menu screen, select Administrative Functions and then
select Patient Directory.
2. Highlight the patient name and press the Select key.
3. Choose Test Directory from the Functions column and press the Select
key.
4. From the Test Directory, highlight Interpretation and press the Select key
to open the Interpretation window.
5. Type in your entry or enter a macro.
6. To enter a macro, press the Notes key and then the two-digit number that
represents the title of the new macro to enter.
7. Press the Select key to exit from the Interpretation screen.
10.5. SIGNAL CLIPPING IN NCS AND EMG
There are four possible courses of action.
i) Swap out recording cables.

ii) Try different channels.
iii)Check settings such as gain, filter, and notch filter settings.
iv)Return to Main Menu screen, select Impedance Test, and then check
electrode impedance.
10.5.2. STIMULUS ARTIFACT
10.5.2.1. WHAT IS A SHOCK ARTIFACT?
The electrical stimulus pulse and surface electrodes give rise to an artifact
consisting of an initial spike and a longer lasting tail which often interferes with
the recorded signal. It has 4 sources:
i) Skin common-mode current escaping through the ground.
Page 97
Xltek NeuroMax
ii) High pass filter characteristics of the amplifier.

iii)Voltage gradient between the recording electrodes caused by a stimulus
current flowing through the limb.
iv)Capacitance coupling between recording and stimulus leads.
The NeuroMax takes care of the first two variables. You can check the
following:
i) Properly connect the patient to the NeuroMax.

ii) Provide a good ground close to the recording electrodes in order to reduce
the common mode potential due to the stimulator.
iii)Reduce the skin to electrode impedances to reduce common mode
voltages, artifacts and 50/60Hz interference.
iv)Avoid crossing stimulator and recording cables to eliminate induced
currents.
v) Keep skin dry between electrodes to prevent bridging of the electrodes.
10.5.3. ELECTRODE IMPEDANCE

NOTE: It is important to keep electrode impedance low and balanced.
Electrode impedance should be kept below 10k (green range) for the best
results in recording low amplitude signals (<50uV peak to peak). Higher
impedance allows the incursion of power line interference (60Hz or 50Hz) and
shock artifacts. Both of these phenomena can obscure your short latency
sensory response. At these impedance levels, it becomes necessary to turn on
your notch filter. Impedance greater than 100K red level with sensory responses
below 100 uV peak to peak are invariably difficult to interpret.
Unbalanced electrode impedance will produce a specific shock artifact. If the

Reference electrode (+) is larger than the Active electrode (-), the shock artifact
will start from above the baseline and sweep down. Similarly, if reversed, the
shock artifact will start from below the baseline and sweep upwards.
Page 98
Xltek NeuroMax
10.5.4. SKIN PREPARATION

NOTE: It is important to work with a clean skin surface.
The skin is a living tissue. As such it is made of various layers. The top three
layers are of crucial importance as they are highly nonconductive. The three
layers are the actual dermis, the dead covering of dry scaly dead skin, and a
layer of oils, sebum, and dirt.
Normal SNAPs require no skin preparation. Clients who have callused, greasy,
dirty, or dry skin require an extra effort on the part of the Physician/Technologist
to obtain good results. Typically washing the skin area of interest (both
recording and stimulus sites) with warm soapy water is adequate. For more
difficult sites or where washing is difficult or inappropriate, rubbing with of an
alcohol swab may be more efficacious. Remember, you are removing these
three layers so use of gentle force may be required. We recommend the use of
a mild abrasive such as Omni-Prep (pumice suspended in a mild detergent), the
hard end of a Q-tip, or rough tissue paper for more difficult situations.
HAZARD WARNING: Rubbing the skin may expose you

to blood borne diseases. It is your responsibility to protect
yourself and the patient from any contact with blood borne
diseases. Please take appropriate care.
10.5.5. ELECTRODE TYPE AND PLACEMENT

Proper electrode to skin connection is vital when attempting to perform a
surface recording.
10.5.5.1. GROUND ELECTRODE
As a general rule, the larger the better. We recommend a stainless steel

electrode with a surface area of at least 5cm2 (0.75 inch2). A few drops of a
conductive paste should be applied to the skin and the ground plate pressed on
top of this. It may be held in place with a piece of tape. Another common
solution is the use of a large disposable self adhesive, pre-gelled electrode.
Place the ground BETWEEN the stimulator and the recording electrodes.
10.5.5.2. RECORDING ELECTRODES
Please be consistent. Always use the same type of electrodes for active and
reference, otherwise your results may not be consistent.
The most common type of electrodes are either metal discs (with conductive
paste) or disposable self-adhesive electrodes. Both are usually about 0.5 to 3
cm2 in area (0.1 to 0.5 inch2).
Page 99
Xltek NeuroMax
The Active electrode (Black - Cathode) is to be placed over the nerve towards
the cathode of the stimulator. The Reference electrode (Red + Anode) is placed
2 to 3cm (distance is set by your procedure) distal to the active electrode
(relative to the cathode of the stimulator), again over the nerve. Make sure that
the skin surface between all 3 electrodes is dry. In addition, stainless steel clip
type electrodes with conductive paste may be used.
We do not recommend the use of steel coil electrodes for recordings if you are
unfamiliar with their use. Slipping the coils onto the digit will disperse the gel
between the two electrodes, usually causing an electrode bridge and
subsequent shorting between the electrodes. Also, using spring coils or spring
electrodes can increase the surface area and also disperse the signal since part
of the surface area is over a silent area of the digit. Stimulus artifact may be
reduced in these situations by covering the segment of the clip that is not over
the nerve with a piece of gauze or tissue paper.
NOTE: YOU WILL ONLY PICK UP A SNAP IF YOUR RECORDING ELECTRODES

ARE PLACED OVER THE CORRECT NERVE. BE AWARE OF ANOMALOUS
INNERVATIONS.
10.5.6. STIMULATOR
Though the NeuroMax can stimulate well by simply pressing the stimulator
prongs against the skin, if the message Stimulator impedance high appears
on the screen you will be required to add a small drop of conducting gel to the
stimulator prongs. Do not spread the gel otherwise the current will spread over
a larger skin area, effectively diminishing the current under the prongs forcing
you to increase the applied current and causing stimulus artifact problems.
10.5.6.1. PATIENT COMFORT
NOTE: A relaxed patient is your friend.
Keep the stimulus current to "just the right amount." Excessive current causes
the patient to feel pain and the NeuroMax to pick up excessive stimulus artifact.
Furthermore, tense patients contract their muscles and inject EMG activity into
the sensory recording. This will make your NCV look very rough making correct
interpretation impossible.
HINT: IF YOU SUSPECT THAT THE MUSCLE BENEATH YOUR ELECTRODES IS

TENSE, TRY TO OBSERVE THIS WITH EITHER A FREE RUNNING SURFACE
EMG OR BY INCREASING THE SPEAKER VOLUME. USE THIS TO HELP RELAX
THE PATIENT.
10.5.6.2. HOW TO STIMULATE
NOTE: Slow and steady.
Page 100
Xltek NeuroMax
The amount of current is determined by slowly increasing the stimulus intensity

until the SNAP appears. Continue to increase the current until the amplitude of
the response ceases to increase. If the patient is obese, has hard, dry skin or
has a neuropathy, then you will have to increase the current beyond normal
limits. Remember, increasing the current will cause the current to spread and to
be shunted in unpredictable ways almost always leading to the formation of a
shock artifact.
10.5.6.3. LEAD WIRES
NOTE: Reduce induced currents.
With individual unshielded recording lead wires, the best results are achieved
when the active and reference lead wires are of the same length and are
loosely twisted together up to the point where they have to branch off to reach
the electrode placements. They should be kept away from other cables and
from the unit's enclosure to minimize interference from power lines and other
external sources.
Similarly, when stimulating with two individual cables from the NeuroMax Stim
Probe, those wires should also be twisted together and kept away from
recording lead wires. This will ensure no increase in stimulus artifact due to
coupling between cables.
In environments with high interference levels, better SNAPs are recorded if you
use the NeuroMax shielded acquisition cable. This cable takes advantage of
NeuroMax‟s unique active differential shield drivers producing efficient shielding
without compromising on common mode rejection and signal bandwidth. This
cable plugs into the 5 pin DIN connector on the headbox and provides alligator
clips for active, reference and ground electrodes.
XLTEK's design differs from other manufacturer's shielded recording cables that
do not support differential shield driving technology and instead rely on simply
grounding their shields. Cables of this type add common mode capacitance to
the input lines causing degradation of high frequency common mode rejection
which in turn causes an increase in stimulus artifact and an increased
susceptibility to high frequency interference. Depending upon cable length,
signal bandwidth may also be compromised. Such cables may reduce power
line interference at the expense of an increase in stimulus shock artifact,
increased high frequency interference, and reduced bandwidth.
10.5.6.4. WHEN ALL ELSE FAILS
Sometimes the obvious solution is the right one. When all else fails, check the
following:
Page 101
Xltek NeuroMax
1. Check your impedance. Keep both low and relatively even.
HINT: IF BOTH ARE EXACTLY THE SAME, SUSPECT A FAULTY GROUND.

UNPLUG THE GROUND, IMPEDANCES SHOULD RISE. IF THEY DO NOT,
CHANGE THE GROUND CABLE.
2. Try running a surface EMG with the volume on. The EMG acts as an
oscilloscope, if there is noise in the system, you may be able to spot it here.
3. Unplug any other devices on the same circuit such as printers, mechanical
beds, vacuum cleaners, or other potential sources of leakage current.
4. A medical grade ground should be installed in your clinic. Some clinics do
not have properly grounded electrical systems.
5. If the patient is tense, ask her to relax.
6. Frequent inspections of your cables will help prevent recording problems.
7. Always have a backup acquisition cable and a backup ground.
8. Are any of the electrodes touching? If so, they are causing a short circuit
and you will develop an artifact.
9. Try pressing X on the keyboard to mathematically remove the shock artifact
from the waveform in the acquisition screen.
10. Rotate the anode around the cathode. This might shunt the shock artifact
away from the recording electrodes.
11. Increase or decrease the pulse duration of the stimulus.
12. Average the sensory response.
10.5.6.5. REDUCING ELECTRODE IMPEDANCE
1. Use an alcohol prep pad to swab the skin to remove any excess sweat or
lotion.
2. Use a mild abrasive paste or pumice tape and gently rub the skin over the
stimulation site to remove dead skin and then swab with the alcohol pad.
3. Instruct patients ahead of time to avoid applying lotion to the skin on the
morning prior to their test.
4. Make sure that the sticky electrodes are adhering properly to the skin. If they
have become loose, replace them with new ones.
Page 102
Xltek NeuroMax
5. Make sure that the Stim probe has some gel on the tips and that there is not
gel all over the patient's skin causing a bridge.
6. Make sure that the patient is properly grounded--good sticky electrode, wet
Velcro ground strap, and good connections in the headbox.
7. When in doubt, try another channel.
10.6. AV STIM
1. Attach the short cable between the NeuroMax and the AV Stim and then
turn on the power to the NeuroMax. When the NeuroMax recognizes the AV
Stim it will provide power to it.
2. When the power is turned on, the green power light on the AV Stim lights up
and the red stimulus light flashes once confirming the initialization of the AV
Stim with the NeuroMax.
3. The printer port of the AV Stim is not active with this version of the
NeuroMax.
10.7. PRINTING
If you are having printing problems, try the following:
10.7.1. NEUROMAX
1. Shut down NeuroMax and printer and then disconnect all cables.
2. Reconnect all cables, turn on the printer, and then turn on NeuroMax.
3. From the Main Menu screen, select Administrative Studies and then
select Patient Directory.
4. Select the patient file and then select Print Report.
10.7.2. PRINTER
 Follow the instructions from the printer manufacturer to print a test page.
 Does the printer need a new toner cartridge?
 Download files to USB mass-storage device and print through Microsoft
Word or XLTEK Archiver on a PC.
Page 103
Xltek NeuroMax
10.8. RECOMMENDED USER PERFORMED

MAINTENANCE
Following a regular schedule of general maintenance will help to prolong the
lifespan of the NeuroMax. Regular maintenance performed by the user does not
involve access to the interior of the NeuroMax; for service problems that require
corrective maintenance and/or internal component service, please call the
XLTEK Service department at 1-800-303-0306, or contact your local XLTEK
representative.
Maintenance performed by the user involves regular inspection and cleaning of

all system components, including the NeuroMax enclosure, keyboard, Screen,
back panel and connectors, headbox and headbox cable, stimulus probe and
cable, printer and printer cable and all electrodes and accessories.
Being an extremely portable system, the NeuroMax will probably be subject to

increased daily wear and tear as compared to previous, larger EMG systems;
this fact has been a very conscious part of the design of all aspects of the
NeuroMax and its performance. That being said, taking basic care of the system
by avoiding extreme physical contact will help prolong the lifespan of the
NeuroMax.
CAUTION:
DISCONNECT THE POWER CORD FROM THE SYSTEM AND THE WALL BEFORE
CLEANING. USE A LINT-FREE CLOTH. DO NOT USE ABRASIVE CLEANERS ON
ANY SYSTEM COMPONENT(SEE NEUROMAX ENCLOSURE BELOW).
Be careful not to allow any excess fluid to seep into the internal electronic
components of the system; be especially careful around the grills located both
on the front panel near the top (i.e. the speaker grill) and on the left side of the
NeuroMax near the back, as well as around the back panel connections and the
headphone jack on the right side near the front.
Page 104
Xltek NeuroMax
10.8.1. NEUROMAX ENCLOSURE

The NeuroMax enclosure can be cleaned with a damp cloth, using water, mild
detergent or cold sterilizing agent. As above, be careful to avoid allowing
excess fluid to seep into any internal components. Since the enclosure is
manufactured using a high-grade ABS resin, there should be no cracks in the
case itself; periodic inspection of the enclosure mounting screws is only
required to ensure that the screws are not coming loose.
Page 105
Xltek NeuroMax
10.8.2. KEYBOARD
The keyboard is made up of discrete keys and cannot be easily cleaned. If any
material were to slip between the keys the NeuroMax can be held upside down
to allow those pieces to drop. Also, individual keys can be cleaned carefully
with Q-tips. Avoiding any sustained exposure to extreme temperatures (above
50o Celsius or below -20o Celsius) will help prolong the integrity of the keyboard.
10.8.3. SCREEN
The screen itself is protected with a front cover made from a mylar-type
material, however the screen uses glass internally, so care should be exercised
not to drop or bump the screen, as this may cause the glass to crack or break.
The screen can be cleaned by wiping with a damp cloth with no water dripping
off or a mild detergent; though a soft lint-free cloth is recommended for cleaning
the screen.
10.8.4. BACK PANEL/CONNECTORS

The back panel of the NeuroMax contains the headbox connector, the printer
connector, the AC power cord connector and the Power ON/OFF switch (and
fuses). The panel itself is made of a heavy grade, reinforced fiberglass material;
avoid any excessive physical stress on the panel itself or any of its components.
Check regularly for any cracks that may have developed in the panel; contact
XLTEK service if you suspect any physical damage to the back panel.
CAUTION:
DO NOT LEAVE ANY CABLES CONNECTED TO THE BACK PANEL WHEN
TRANSPORTING THE NEUROMAX; DOING SO MAY CAUSE THE CONNECTORS
TO COME LOOSE, AND/OR MALFUNCTION. THE BACK PANEL AND
CONNECTORS SHOULD ONLY BE CLEANED WITH A DRY, SOFT, LINT-FREE
CLOTH.
10.8.5. HEADBOX AND CABLE

The headbox should only be cleaned with a dry, soft, lint-free cloth. Check
regularly to see if any of the electrode connections have become loose; if so,
contact XLTEK service. The headbox itself is a completely passive electronic
device, but care should still be taken to avoid extreme physical stress to the
headbox. Check periodically to determine cable integrity.
DO NOT LEAVE THE HEADBOX ATTACHED TO THE NEUROMAX WHEN

TRANSPORTING THE UNIT.
10.8.6. STIMULUS PROBE AND CABLE
Page 106
Xltek NeuroMax
The stimulus probe body and cable can be cleaned with a soft, lint-free cloth or
a damp cloth soaked in water, mild detergent, or a cold sterilizing agent.
Determine cable integrity regularly. The stimulus probe headpieces can be
cleaned in the same fashion as the body, but extra care should be taken to
remove all electrode gels or pastes that have been used on the headpieces;
avoid any long term build-up of gels or pastes on the stimulus probe
headpieces, as this may interfere with the optimal performance of the stimulus
probe. If the various headpieces do not fit snugly into the probe body, replace
them immediately to ensure optimal performance.
10.8.7. PRINTER AND CABLE

The NeuroMax must be used with an approved electronic device. The
approvals should be IEC 950 or equivalent. It can also be IEC 601-1 + A1:1991
+ A2: 1995\EN60601-1.03.96 approved. The printer is attached via a standard
USB connector on the NeuroMax.
DO NOT LEAVE THE PRINTER ATTACHED TO THE NEUROMAX WHEN

TRANSPORTING THE UNIT.
10.8.8. ELECTRODES AND ACCESSORIES

Regularly clean all surface electrodes and accessories with warm, soapy water
or liquid sterilizing agents; ensure that all gels and/or pastes are removed from
the electrodes and their cables. Follow the electrode manufacturers' instructions
for cleaning and/or sterilizing all electrodes and accessories.
While the NeuroMax has been carefully designed and manufactured to be as

reliable and durable as possible, regular cleaning and inspection of system
components can only help the long term trouble-free operation of the system.
As with other types of medical instrumentation, try to avoid extremes of physical
stress (i.e. dropping the unit, etc...) and sustained exposure to extreme
temperatures. If you suspect any problem that might impact on the safety or
effectiveness of the NeuroMax, call XLTEK Technical Support at 1-800-303-
0306, or your local XLTEK representative.
10.9. USER ADJUSTMENTS

If you experience any trouble operating the NeuroMax, it is possible that many
of the problems may be overcome through simple user adjustments. This
chapter offers a few suggestions designed to overcome some of the more
commonly found difficulties; if you experience any trouble that is not described
in this section, or if the suggestions here do not correct the difficulty you are
having, please call XLTEK Technical Support or your local XLTEK
Representative for service.
Page 107
Xltek NeuroMax
10.9.1. NO ELECTRICAL STIMULUS

The patient does not feel the stimulus pulse, or does not respond to any pulse
as expected. The stimulus probe or stimulating electrodes connected to the
probe do not deliver any electrical stimulus. Check the following:
1. Check the lower right corner of the screen, in the stimulator status area, to
see that the "STIMULATOR ON" message is displayed. If the display reads
"OFF", press the START/STOP switch once to activate the stimulator.
2. Check the stimulator status area to determine that the intensity level, in mA,
is appropriately set for the current test.
3. Check the connection between the stimulator probe cable and the headbox to
ensure that the fit is snug.
4. Check the connection between the headbox and the NeuroMax (at the back
on the lower right side of the NeuroMax to ensure that the headbox is properly
connected - be sure to tighten the thumbscrews so that the headbox cable does
not come loose.
5. Check that the skin between the two stimulating electrodes (i.e. anode and
cathode) is clean and free from any layer of conducting gel or paste that might
create a bridge between the anode and cathode.
6. Press MAIN MENU to exit to the main menu, and then re-enter the current
test to reset all software and hardware settings for the stimulus.
7. Check that the "Stimulator Impedance High" error message does not appear
when you attempt to stimulate. If it does, clean the stimulus site on the skin and
prepare the site with some type of abrasion (e.g. Omni-Prep) to decrease the
impedance level.
10.9.2. NO RESPONSE FROM ELECTRODES

A. In NCS or EMG Mode - The acquired waveforms are flat, do not appear, or
do not appear correct (or as expected). Check the following:
1. Make sure that the patient electrodes are connected to the correct amplifier
channel in the headbox. In all test modes, the screen will display the currently
active channel beside the test name in the data table area; check that the active
channel corresponds to where the patient electrodes are connected in the
headbox.
Page 108
Xltek NeuroMax
2. Check that the patient electrodes fit properly into the headbox (not loosely),
and also check that there are no apparent breaks in the patient electrode
cables.
3. Check the patient electrode impedance levels - if the impedance levels are
too high, you may need to replace the electrode, electrode cable, or simply re-
prep the recording site on the skin. Make sure that the positive and negative
recording electrode sites have similar impedance values.
4. Check the connection between the headbox and the NeuroMax to make sure
that it is tight.
5. Check the screen gain and timebase settings to ensure that they are
appropriate for the current test. You may also want to check the LFF, HFF, and
Notch Filter settings, as well as any sweep or trigger delays being used.
6. Press MAIN MENU to exit to the main menu, and then re-enter the current
test to reset all software and hardware settings for the amplifiers
B. In Dual Channel Mode, check for all of the above situations, and then check
the following:
1. If the current test calls for averaging, check that the "AVERAGER ON"
message is displayed on the screen. If it is not shown, press the AVERAGER
hardkey.
2. If the AVERAGER is "ON", check the raw data display to ensure that
appropriate data is actually being acquired through the amplifiers (Press space
bar to display raw data). If the raw data display is flat, then no data is being
acquired by the amplifier(s).
10.9.3. LARGE STIMULUS ARTIFACT

There appears to be an excessively large stimulus artifact at the beginning of
each triggered waveform; this can occur in any NCS or Dual Channel test, and
may cover up the actual waveform of interest. Check the following:
2. Check the integrity of the ground electrode cable. If it appears broken or bent
at all, try replacing it.
3. Position the ground electrode between the stimulating electrode (or probe)
and the active recording electrode.
Page 109
Xltek NeuroMax
4. If you are using a non-disposable, metal ground electrode plate, check that
there is no corrosion or build up of gel on either the surface of the plate or the
contact between the plate and the cable.
5. Check that the amplifier gain setting is appropriate for the current test. It is
possible that you may be over-amplifying the signal being recorded, and thus
over amplifying the stimulus artifact.
6. If you are using single shot stimulus mode, or even if you are using train
mode with a low number of pulses per train, try using AVERAGED acquisition
(i.e. press the AVERAGER hardkey to turn on the Averager) to reduce the
influence of the variable "noise" of the Stimulus artifact.
10.9.4. NOISY DATA

The data being displayed on the screen seems excessively noisy. Check the
following:
1. Make sure that the patient electrodes are connected to the correct amplifier
channel in the headbox. In all test modes, the screen will display the currently
active channel beside the test name in the data table area; check that the active
channel corresponds to where the patient electrodes are connected in the
headbox.
2. Check that the patient electrodes fit properly into the headbox (not loosely),
and also check that there are no apparent breaks in the patient electrode
cables.
4. Check the connection between the headbox and the NeuroMax to make sure
that it is tight.
5. If everything appears prepared and set up as it should be and there still

appears to be noise in the data being acquired, try using the other acquisition
channel. To switch acquisition channels, put the active and reference recording
electrode cables (or the 5 pin D.I.N. cable) into the other channel designated on
the headbox, and then press the CHANNEL SELECT button on the keypad to
--- switch recording channels. The data area of the screen will always display
which channel is currently being used.
Page 110
Xltek NeuroMax
10.9.5. UNIT DOES NOT POWER ON

The unit does not power on when the "on" switch is pressed. Check the
following:
1. Check both ends of the AC power cord to ensure they are connected to the
unit and the wall properly (use only an approved hospital grade, 3 pronged
outlet for AC connection).
2. Check that the green LED for "power On" is lit up (this can be found below
the screen on the left side of the front screen panel). If the power on LED
appears to be lit and the screen is not on, call XLTEK service.
3. Check the fuse which is located beside the ON/OFF switch on the back
panel. If the fuse needs replacing, replace only with two T3.15A/250 V fuse.
Page 111
Xltek NeuroMax
10.9.6. ERROR MESSAGES

Should any Windows error messages appear on your screen, they can always
be removed by pressing either ENTER or ESC. Pressing ENTER will select the
action highlighted. Pressing ESC will cause the action to be cancelled. We
recommend that you always press ESC whenever a Windows error message
comes to the screen.
There are also a few NeuroMax error messages which may appear from time to
time when you are using the NeuroMax EMG system. Most of these messages
have simply been designed to warn you that less-than-perfect testing conditions
exist, or that you must do something to continue in a test mode. If any of these
messages are unclear, please call your XLTEK representative. The following
messages are presented in alphabetical order.
"Are you sure(Y/N)? If yes, current waveforms will be lost"

This message only appears when you have existing information in the patient
information screen (i.e. the active or current patient file) and you select NEW
PATIENT. When the system has been turned on and you are testing a patient
(with patient info already entered), you may decide to press PATIENT INFO to
enter the patient information screen. When you do this there are two choices
shown - 1. Edit Current Patient, and 2. New Patient. If you SELECT the first
option (Edit Current Patient), the cursor will move to the first patient information
field and you can now edit existing information and/or make additions to the
existing patient information screen. If you have finished testing the current
patient and now have a new patient, this error message is simply warning you
that the WAVEFORMS will be lost. It is important to know that you will not lose
the existing patient file, the existing final report or the existing test files complete
with all of the numeric data; only the actual waveforms will be lost. If required,
you can exit the patient info screen, press REPORT and choose STORE
REPORT WITH WAVEFORMS. However, if you simply select new patient, the
complete patient file, minus only the actual waveforms, is automatically stored.
"Erase Trace(s) to Acquire more data"

The NeuroMax can acquire up to eight traces per dual channel test screen, and
up to twenty stored traces for all F-wave and H-reflex tests. Once you have
acquired a complete set of data for any one of these tests (i.e. all trace locations
have waveforms), you cannot acquire any more data for the current test. If you
try to acquire more data in this instance, the screen will display the error
message shown above. There are two ways to acquire more data in this case:
1. You may choose to erase a particular trace or set of traces
-OR-
Page 112
Xltek NeuroMax
2. Press TEST MENU, and re-select the current test to acquire a new set of
data while automatically storing the old set of data.
Once again this error message appears simply to let you know that you must
proceed in a particular fashion, so that no test data is ever inadvertently erased.
"WARNING: the flash memory is almost full"

The permanent storage capacity of the NeuroMax is almost full. There will not
be enough memory available to store all data and waveforms for the current
patient if the test is too large. To proceed with the current test, you must first
make additional memory available by deleting some patient final reports from
the patient directory, remembering that reports stored with waveforms require
substantially more memory than reports only.
"Previous data will be erased. To accept, press Y. Any other

key to keep present data and not start stimulator."
You are in the RECORD mode of the F wave test modality. You have already
acquired a set of F wave responses which are displayed on screen, with the
associated data values in the data table. When you press the START/STOP
switch to begin another train of stimuli or deliver a single shot stimulus, this
error message appears. If the existing data set on screen is inadequate and you
wish to erase them and acquire a new set, press Y and then START/STOP to
erase the existing trace set and acquire a new set. If you wish to keep the
existing set and acquire a second set for comparison later on, press N, and then
press TEST MENU to re-select the F wave study and acquire a new set of
responses. By going through the TEST MENU, you are in essence doing a
"new" test, and once completed the patient file will have both F wave tests, with
their associated test times, in storage. In this manner, you can do a couple of
tests, and then at some later time edit or delete one of the tests, keeping the
other one for your final report.
"Printer Error"
This message only appears when you attempt to either print a screen copy or a
final report. The printer is either not connected to the NeuroMax, or it is not
powered on. When the NeuroMax is initially powered on, AC power is
immediately supplied to the printer; however, if for some reason the printer is
turned off during testing, you must press the printer's POWER ON button to re-
initialize the printer.
"Printer Out Of Paper"

This message only appears when you attempt to either print a screen copy or a
final report. The printer is simply out of paper, and you must feed either a single
sheet into the drive mechanism or load the sheet feeder with more paper.
"Out of Range"
Page 113
Xltek NeuroMax
You have either entered an invalid number for the number of pulses in the train
or You have entered an invalid number for the stimulus frequency. The
maximum number of pulses allowed in any single train is 60 pulses; the
minimum number is 2 pulses. Therefore the number of pulses that can be
entered is between 2 and 60 pulses. The stimulus frequency range is nominally
0.0 Hz to 50.0 Hz; the number entered must be lower than 50.0. You may
choose any value below 50.0, accurate to one decimal place (i.e. 27.8 Hz is
acceptable).
For patient safety and comfort however, the maximum stimulus frequency is
also dependent upon the pulse duration chosen, such that at higher stimulus
pulse durations, the maximum frequency available is decreased (see Table 9.1
below).
Table 9.1 - Maximum Stimulus Frequencies at all Pulse Durations
Pulse Max. Stim

Duration Frequency
0.05 ms 50.0 Hz
0.10 ms 50.0 Hz
0.20 ms 25.0 Hz
0.30 ms 16.6 Hz
0.50 ms 10.0 Hz
1.00 ms 5.0 Hz
"Stimulus Impedance High"

The NeuroMax has been designed to deliver a constant current stimulus pulse
throughout a wide range of skin impedances; the current will be constant as
long as the impedance is below 4,000 Ohms. Above this level, the actual
current being delivered to the patient may be less than the pre-determined
value chosen by you. To warn you of this situation, whenever you try to deliver
a stimulus pulse and the impedance level is over 4.0 kOhms, the system will
deliver the pulse and display the error message superimposed above the trace
that was acquired. The best course of action is to improve the skin preparation
of the site used for stimulating. Alternately, you may wish to check the integrity
of any electrode or electrode cable you are using to deliver the stimulus pulse to
the patient.
"This test is not yet defined for the selected nerve"

You are in the Nerve Conduction Studies TEST MENU, and have already
selected a nerve to test. The selected nerve appears in the menu as a
highlighted selection. For a particular nerve, only certain tests have been
defined, and you currently have highlighted a test which is NOT defined. If you
continue on by pressing the SELECT switch, the default NCS test screen will
Page 114
Xltek NeuroMax
appear. Press the left or right arrows of the SELECTOR SWITCH and see that
as you highlight different tests for the selected nerve, the error message will
appear and disappear, depending on which test is highlighted. As an example, if
you choose RADIAL nerve and then highlight "H Reflex", the error message
appears, because no H reflex test has been defined for the radial nerve. If you
now press the left arrow three times to move to SNC, this test has been defined,
so the error message will disappear.
"To move to the RECORD screen, at least one M wave must be

obtained."
You are currently in the SET UP mode of either the F wave or Repetitive
Stimulation test, and you have pressed the SELECT switch to move to the
RECORD mode. In the SET UP mode of these two tests, the first step is to
acquire an appropriate M wave response before proceeding to the RECORD
mode. The system requires that you have at least one M wave on screen before
moving to the RECORD mode. Press the START/STOP switch to acquire an M
wave response before pressing SELECT to move to the RECORD mode.
10.10. CHECKING CALIBRATION OF NEUROMAX

The factory calibration is digitally stored on the unit and should NOT be
modified outside the factory. External checking of the calibration may be
performed. The accuracy of the stimulator is better than 1% in both amplitude
and duration. The accuracy of the waveform acquisition section is also better
than 1% in both amplitude and time.
A calibrated oscilloscope and a calibrated signal generator are required to

calibrate the unit. Attach the Headbox to the NeuroMax; insert the stimulator
into the headbox and proceed with the calibration.
Page 115
0
Encl osure/Basic insulation
11.
EMG
Type BF
Speaker
Applied Part
Digital I/ O EMG Input
Xltek NeuroMax
Line Out
Audio Am plifie r / Stim 1
Headpho ne Accessorie s Type BF
Applied Part
Hand sw itch Digital I/ O St im 1Ou t
Mute Prob e Stim 2
Type BF
Applied Part
Meta l Shield Parts with Protective Earth
Digital I/ O St im 2Ou t
Video Card
Video Output
(Neuro only)
Ou tput to Miniscreen
PC/104 Plus Bus Ty pe F
Et hernet
Applied Part
Rear Panel DSP
USB1/U SB2 I/O
PC/104 Plus Bus
USB3
BLOCK DIAGRAM
Si ngle Board Touch Scr een/

Comput er Knob Control Touch Screen
Auxiliar y
Power Disp lay
Outlet
Fl
exible cord Backlight
Po wer: Po wer: Power
wi thMains
Primary Secondar y Distributio n
Plug
Page 116
Switch Fuse s
Reinforced insulation Protect ively Earthe d
between the primary Intermediate Ci rcuits
and seco ndary of the
po wer suppl y
Protec tive
Earth
Metal Shield Parts wi thProtec tive Eart h
Potent ia l
Equalization
Terminal Re v A 8-25-2009
Xltek NeuroMax
3.3V/5V
VCCA HR1x3(3.3V:Close;5V:Open)
CON1
3
2
1
L1 1
V_CAL R27 R25 R24 CAL_SIG RST
POWER
2 3V3
22µH/±10%/1.7ohm/80mA(LB2012T220K/8030984) 3
10k/1% 1M/1% 1M/1% 4
5V
C27
C26
C25
CAL voltage d ivider 1:20000 CAL_SIG should be PWM output GND
1 5
Square wa ve Ca li bration Signal GND
2 R26 When 5V p ower suppl y i s used: Z1 PWR 6 VIN
100R/1% Frequency is set to be approx: (10-14)Hz
GYX-SD-TC0805SURK(RED)
100nF/X7R/10%
5Vp-p +/-10% => 250µVp-p +/-10%
10µF/6.3V/0805
10nF/X7R/10%
HR1x2(Open)
BZV55C6V2 NA(PN1X6)
When 3.3V power sup pl y is use d:
AIN_SEL CON2
GND_CAL R28 3.3Vp -p +/-10% => 1 65µVp-p +/-10 % R29 2 1 1 A0
2k/1% 4 3 2
ANALOG
10k/1% A1
6 5 3 A2
8 7 4 A3
V_REF 10 9 5 A4
12 11 6
A5
HR2x6(1-2:Close) NA(PN1X6)
CON3
1
D0
2 D1
D4/D9 3 D2
DIGITAL
HR1x3(D4:Open;D9:Close) 4 D3
VCCA D4 5
D4
6 D5
D9 7 D6
8 D7
3
2
1
VCCA VCCA R19 NA(PN1X8)
330R CAL_SIG CON4
C10 C22 1 D8
3V_REF_ADC 2
D9
3 D10
DIGITAL
100nF/X7R/10% 100nF/X7R/10%
R22 R20 4
SR1
C21
C20
C19
C18
REF_E D11
8
8
IC2A 3 10k/1% 2k/1% C17 5
HR1x2(Open) D12
C11 1.5V_REF_BUF 1 C 6
D13
2 1.5V_REF 7
1uF/X5R/10%
10nF/X7R/10%
100nF/X7R/10%
100nF/X7R/10%
10µF/6.3V/0805
TLC277IDR GND
100nF/X7R/10% 3V_REF_ADC
1
2
R 8
C23 AREF
4
4
A
C12 100nF/X7R/10%
R23 R21 NA(PN1X8)
AP431SA
10k/1% 10k/1%
100nF/X7R/10% C24
+
V_REF V_REF
47µF/10%/6.3V/TANT(C)/ESR/0.25ohm(TR3C476K6R3C0250/1754044)
Instrumental Amplifier High-Pass filter OAmp with regulated gain! High-Pass filter 3rd order "Besselworth" filter, fc = 40Hz.
1 pole G=1+R12/(TR1+R11) 1 pole
G=5*(1+R8/R7)=10 G= (R17/R16)+1= 3.56
High Voltage protection HF rejection Fc=0.16Hz G=5,76...101 Fc=0.16Hz
R5 NA(3.3M) V_REF
R7 10k/1% R8 10k/1%
R1 R3 2k/1% C28 NA C13 10nF/X7R/10%
CH1_IN-
PG B1 0 1 0 6 0 3 MR( F 2 5 9 4 T R- ND) PG B1 0 1 0 6 0 3 MR( F 2 5 9 4 T R- ND)
2k/1% IC1A
U1 R30 R31 IC1B
C2
PGS1
VCCA C7
100pF/COG/5%
CH_IN 0R(boa d m o unted ) 0 R(boad m ounted) MCP607-I/SN MCP607-I/SN

D1 5 6 3
REF R14 R15
160k 40k 4 0k 160k
0R 0R
VOUT 1 C9 5
R32 2
A1 A2
1 1uF/X5R/10% 2 7 R18
C1
A3
3-R 56k/1% 330k/1%

VCCA
BAV199(1156415)
3
VIN- RG 8 1uF/X5R/10% R16 6
VIN+ SHUTDOWN 4 C29 NA 3.9k/1%
C3
BAV199(1156415)
2 2k/1% 10nF/X7R/10% 7 R12 100k/1%
100pF/COG/5%
VCCA V+ V- TR1 3.9k/1% R17 10k/1%

R10 R13
PGS2
C14
CH1_IN+
1-L R11
2
V_REF D2 1M/1% 3 20k 1 C8 1nF/X7R/10% 1M/1%
SCJ325P00XG0B02G V_REF INA321EA
10nF/X7R/10% C15 1nF/X7R/10% C16
R2 R4 2k/1% C4 100nF/X7R/10% 3 1 1k/1%
1uF/X5R/10%
2k/1% R6 NA(3.3M) V_REF C5 1uF/X5R/10%
V_REF V_REF V_REF V_REF V_REF

C6 1uF/X5R/10%
IC2B
6 R9
TLC277IDR
7
5
100k/1%
Page 117
Xltek NeuroMax
INDEX
EOG Protocol
configuring ........................................................... 72
A EOG Test
Administrative Functions ......................................... 83 about .................................................................... 72
AEP EP Test
impedance check................................................ 77 setting up ............................................................. 51
protocols .............................................................. 77 ERG Protocol
AV Stim configuring ........................................................... 71
cautions ................................................................ 75 ERG Test
AV Stim 1000 ........................................................... 73 about .................................................................... 71
calibration & maintenance ................................. 76
connecting ........................................................... 74 F
front panel ............................................................ 73
rear panel............................................................. 73 Files
warnings............................................................... 75 RTF ...................................................................... 88
warnings & cautions overview .......................... 75 Function Keys .......................................................... 25
F-Wave Test
about .................................................................... 40
B hints & features................................................... 43
Batch Print ................................................................ 86 performing ........................................................... 41
Blink Reflex Test
about .................................................................... 57 H
conducting ........................................................... 57
setting up ............................................................. 57 Hot Keys ................................................................... 27
H-Reflex Response
acquiring .............................................................. 44
C H-Reflex Test
setting up ............................................................. 44
Calibrating
NeuroMax .......................................................... 115 HRV Test
about .................................................................... 61
stimulator ........................................................... 115
conducting ........................................................... 61
Cautions .................................................................... 20
setting up ............................................................. 61
Control Keys ............................................................. 24
D I
Incremental Stim Test
Defaults
about .................................................................... 58
editing test ........................................................... 81
conducting ........................................................... 60
setting test ........................................................... 80
setting up ............................................................. 58
values................................................................... 60
E In-Service Checklist ................................................ 90
Introduction............................................................... 13
EMG
acquiring .............................................................. 46
activating triggers ............................................... 49 K
analyzing motor units ......................................... 50
free run ................................................................. 48 Key Pad .................................................................... 24
saving a test ........................................................ 50
triggered features ............................................... 49 M
turns & amplitude................................................ 48
EMG Notepad Macro
edit ........................................................................ 87 creating ................................................................ 96
EMG Suite using pre-defined ............................................... 97
creating .......................................................... 81, 95 Main Menu ................................................................ 23
using ..................................................................... 95 Manual
EMG Tests using..................................................................... 14
about .................................................................... 45 Memory Management ............................................. 85
setting up ............................................................. 45 Multi-Channel EMG/IOM ........................................ 64
Page118
Xltek NeuroMax
Multi-Channel Nerve Conductions......................... 65 Stored Data

changing date on ................................................ 87
Studies
N editing .................................................................. 96
Nerve Conduction Study Sympathetic Skin Respose (SSR) ........................ 63
conducting ........................................................... 36 System Options ....................................................... 86
creating ................................................................ 94
editing ................................................................... 94 T
setting up ............................................................. 34
setting up sites .................................................... 94 Test Menu
Nerve Conduction Tests modifying parameters ........................................ 80
about .................................................................... 33 Test Reports
NeuroMax generating ........................................................... 30
1002...................................................................... 12 Troubleshooting ....................................................... 97
1004...................................................................... 12 AV Stim .............................................................. 103
about .................................................................... 15 electrode impedance ......................................... 98
operating conditions ........................................... 15 electrode type & placement .............................. 99
operating environment ................................. 13, 15 error messages................................................. 112
transport and storage ......................................... 15 large stimulus artifact ....................................... 109
no electrical stimulus ....................................... 108
no electrode response ..................................... 108
P no power ............................................................ 111
P 300 Test noisy data .......................................................... 110
getting started ..................................................... 65 preventative maintenance ............................... 104
hints & features ................................................... 67 printing ............................................................... 103
options.................................................................. 69 signal clipping ..................................................... 97
running ................................................................. 67 skin preparation .................................................. 98
Patient Directory ...................................................... 84 stimulator ........................................................... 100
Patient File stimulus artifact................................................... 97
creating ................................................................ 29 user adjustments .............................................. 107
Patient Info Troubleshooting & Maintenance............................ 93
edit ........................................................................ 87
U
R
USB
Rep Stim Test saving files to device.......................................... 88
about .................................................................... 37
hints & features ................................................... 43
performing ........................................................... 38
V
Report Format VEP
edit ........................................................................ 87 acquiring fulfield response ................................ 78
Report Functions...................................................... 30 acquiring hemifield response ............................ 79
Reports impedance check ............................................... 78
managing ............................................................. 88 protocols .............................................................. 77
S W
Select Keys ............................................................... 25 Warnings................................................................... 18
SEP Test ................................................................... 53 Warnings & Cautions
protocols .............................................................. 54 about .................................................................... 17
Site Name List Waveform
edit ........................................................................ 87 checking ............................................................ 116
Software Welcome ................................................................... 12
checking version ................................................. 93
updating ............................................................... 93
Page119
A Total Service Solution
Standing behind every XLTEK product is Natus Medical Incorporated, an

internationally respected innovator of medical products and services.
Our Neurology systems are backed up by an in-house support team staffed with
technical and clinical experts, 24/7 support, remote support via WebEx or VPN, the
largest clinical and technical field support network in Neuro/Sleep and customized
service contracts that include preventative maintenance visits and computer
upgrades.
Natus Medical Incorporated

Excel-Tech Ltd. (XLTEK)
2568 Bristol Circle
Oakville, Ontario
L6H5S1 Canada
T: +1 905.829.5300
F: +1 905.829.5304
www.natus.com P/N 105352 Rev E

Electromiografo Marca Xltec Modelo Neuromax 1004

Uploaded by

Copyright:

Available Formats

Electromiografo Marca Xltec Modelo Neuromax 1004

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Electromiografo Marca Xltec Modelo Neuromax 1004

Uploaded by

Copyright:

Available Formats

XLTEK NEUROMAX

Natus Medical Incorporated

EUROPEAN AUTHORIZED REPRESENTATIVE:

Copyright © 2012 by Excel-Tech Ltd. (XLTEK)

NEUROMAX SAFETY AND STANDARDS CONFORMITY 6

1. WELCOME TO THE NEUROMAX 12

2. THE XLTEK NEUROMAX 15

2.1. OPERATING CONDITIONS 15

3. NERVE CONDUCTION TESTS 33

3.1. MOTOR AND SENSORY NERVE CONDUCTIONS 34

3.1.1. SETTING UP A NERVE CONDUCTION STUDY 34

4.1. SETTING UP THE EMG TEST MENU 45

5.1. OTHER TESTS 50

5.9.2. CONFIGURING THE E0G PROTOCOL 72

6.1. AV STIM 1000 FRONT PANEL 73

7. SETTING THE DEFAULTS 80

7.1. TEST MENU PARAMETERS 80

8.1. ADMINISTRATIVE FUNCTIONS 83

9. APPENDIX 1: IN-SERVICE CHECKLIST 90

10. APPENDIX 2: TROUBLESHOOTING 93

10.2. NERVE CONDUCTIONS 95

10.4. ADMINISTRATIVE FUNCTIONS 96

10.5.2. STIMULUS ARTIFACT 97

11. BLOCK DIAGRAM 116

NEUROMAX SAFETY AND STANDARDS CONFORMITY

STANDARDS COMPLIANCE AND NORMATIVE REFERENCES

1. Type of protection against electric shock: Class I

Table 1 – Safety Standard of Compliance and Normative References

CAN/CSA C22.2 No 601.1-M90 Medical Electrical Equipment part 1: General requirements

IEC 601-1:1988 + A1:1991 + Medical electrical equipment - Part 1: General requirements

IEC 60601-2-40 (1998-02) Medical Electrical Equipment part 2-40: Particular

Table 2 – EMC Standard of Compliance and Normative References

EN 60601-1-2 :2001 (2nd Edition) Medical Electrical Equipment, Part 1-2:General

IEC 61000-3-3:1994 / EN 61000-3- Electromagnetic compatibility (EMC) - Part 3-3: Limits -

DECLARATION OF COMPLIANCE FOR IEC 60601-1-2

Guidance and manufacturer’s declaration – electromagnetic emissions

Emissions Compliance Electromagnetic environment - guidance

Table 2 - Electromagnetic Immunity

Guidance and Manufacturer’s Declaration – Electromagnetic Immunity

Guidance and Manufacturer’s Declaration – Electromagnetic Immunity

Immunity test IEC 60601 Compliance Electromagnetic environment - guidance

where P is the maximum output power rating of the

marked with the following symbol:

Table 4 - Recommended Separation Distances

Recommended separation distances between portable and mobile RF communications

DECLARATION OF COMPLIANCE FOR FCC

Warning: Changes or modifications not expressly approved by the manufacturer could

The NeuroMax offers full-featured EMG in a simple,

XLTEK NeuroMax 1002 CE

XLTEK NeuroMax 1004 CE

XLTEK Headboxes and Accessories

1.1.1. INTENDED USE

1.2. CUSTOMER SERVICE

1.3. USING THE MANUAL

The manual presents step-by-step instructions

The in-depth procedures describe the detailed

When going through the procedures, we

We have also placed TIPS and NOTES alongside

2. THE XLTEK NEUROMAX