3.2.2 Arduino Uno

Download as docx, pdf, or txt
Download as docx, pdf, or txt
You are on page 1of 8

3.2.

2 ARDUINO UNO

The Arduino Uno is a microcontroller board based on the ATmega328


(datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM
outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power
jack, an ICSP header, and a reset button. It contains everything needed to support
the microcontroller; simply connect it to a computer with a USB cable or power it
with a AC-to-DC adapter or battery to get started. The Uno differs from all preceding
boards in that it does not use the FTDI USB-to-serial driver chip. Instead, it features
the Atmega16U2 (Atmega8U2 up to version R2) programmed as a USB-to-serial
converter.

SPECIFICATION

Microcontroller ATmega328

Operating Voltage 5V

Input Voltage (recommended) 7-12V

Input Voltage (limits) 6-20V

Digital I/O Pins 14 (of which 6 provide PWM o/p)

Analog Input Pins 6

DC Current per I/O Pin 40 mA

DC Current for 3.3V Pin 50 mA

Flash Memory 32 KB of which 0.5 KB used by bootloader

SRAM 2 KB (ATmega328)

EEPROM 1 KB (ATmega328)
Clock Speed 16 MH

Fig 3.6 Atmega328 pin description


Fig 3.7 Arduino controller board description

POWER

The Arduino Uno can be powered via the USB connection or with an external
power supply. The power source is selected automatically.

External (non-USB) power can come either from an AC-to-DC adapter (wall-
wart) or battery. The adapter can be connected by plugging a 2.1mm center-positive
plug into the board's power jack. Leads from a battery can be inserted in the Gnd
and Vin pin headers of the POWER connector.

The board can operate on an external supply of 6 to 20 volts. If supplied with


less than 7V, however, the 5V pin may supply less than five volts and the board may
be unstable. If using more than 12V, the voltage regulator may overheat and damage
the board. The recommended range is 7 to 12 volts.

The power pins are as follows:

 Vin, The input voltage to the Arduino board when it's using an external power
source (as opposed to 5 volts from the USB connection or other regulated
power source). You can supply voltage through this pin, or, if supplying
voltage via the power jack, access it through this pin.
 5V. The regulated power supply used to power the microcontroller and other
components on the board. This can come either from Vin via an on-board
regulator, or be supplied by USB or another regulated 5V supply.
 3V3. A 3.3volt supply generated by the on-board regulator. Maximum current
draw is 50 mA.
 GND. Ground pins.

MEMORY

The ATmega328 has 32 KB (with 0.5 KB used for the bootloader). It also has
2 KB of SRAM and 1 KB of EEPROM (which can be read and written with
the EEPROM library).

INPUT AND OUTPUT

Each of the 14 digital pins on the Uno can be used as an input or output,
using pinMode(), digitalWrite(), and digitalRead() functions. They operate at 5
volts. Each pin can provide or receive a maximum of 40 mA and has an internal pull-
up resistor (disconnected by default) of 20-50 kOhms. In addition, some pins have
specialized functions:
 Serial: 0 (RX) and 1 (TX). Used to receive (RX) and transmit (TX) TTL
serial data. These pins are connected to the corresponding pins of
the ATmega8U2 USB-to-TTL Serial chip.
 External Interrupts: 2 and 3. These pins can be configured to trigger an
interrupt on a low value, a rising or falling edge, or a change in value. See
the attachInterrupt() function for details.
 PWM: 3, 5, 6, 9, 10, and 11. Provide 8-bit PWM output with
the analogWrite() function.
 SPI: 10 (SS), 11 (MOSI), 12 (MISO), 13 (SCK). These pins support SPI
communication using the SPI library.
 LED: 13. There is a built-in LED connected to digital pin 13. When the pin
is HIGH value, the LED is on, when the pin is LOW, it's off.

The Uno has 6 analog inputs, labeled A0 through A5, each of which provide 10 bits
of resolution (i.e. 1024 different values). By default they measure from ground to 5
volts, though is it possible to change the upper end of their range using the AREF
pin and the analogReference() function. Additionally, some pins have specialized
functionality:

 TWI: A4 or SDA pin and A5 or SCL pin. Support TWI communication


using the Wire library.

There are a couple of other pins on the board:

 AREF. Reference voltage for the analog inputs. Used


with analogReference().
 Reset. Bring this line LOW to reset the microcontroller. Typically used to add
a reset button to shields which block the one on the board.
See also the mapping between Arduino pins and ATmega328 ports. The mapping
for the Atmega8, 168, and 328 is identical.

COMMUNICATION

The Arduino Uno has a number of facilities for communicating with a


computer, another Arduino, or other microcontrollers. The ATmega328 provides
UART TTL (5V) serial communication, which is available on digital pins 0 (RX)
and 1 (TX). An ATmega16U2 on the board channels this serial communication over
USB and appears as a virtual com port to software on the computer. The '16U2
firmware uses the standard USB COM drivers, and no external driver is needed.
However, on Windows, a .inf file is required. The Arduino software includes a serial
monitor which allows simple textual data to be sent to and from the Arduino board.
The RX and TX LEDs on the board will flash when data is being transmitted via the
USB-to-serial chip and USB connection to the computer (but not for serial
communication on pins 0 and 1).

A SoftwareSerial library allows for serial communication on any of the Uno's digital
pins.

The ATmega328 also supports I2C (TWI) and SPI communication. The Arduino
software includes a Wire library to simplify use of the I2C bus; see
the documentation for details. For SPI communication, use the SPI library.

PROGRAMMING

The Arduino Uno can be programmed with the Arduino software.


The ATmega328 on the Arduino Uno comes preburned with a bootloader that
allows you to upload new code to it without the use of an external hardware
programmer. It communicates using the original STK500 protocol (reference, C
header files).
AUTOMATIC (SOFTWARE) RESET

Rather than requiring a physical press of the reset button before an upload, the
Arduino Uno is designed in a way that allows it to be reset by software running on
a connected computer. One of the hardware flow control lines (DTR) of
theATmega8U2/16U2 is connected to the reset line of the ATmega328 via a 100
nanofarad capacitor. When this line is asserted (taken low), the reset line drops long
enough to reset the chip.

The Arduino software uses this capability to allow you to upload code by
simply pressing the upload button in the Arduino environment. This means that the
bootloader can have a shorter timeout, as the lowering of DTR can be well-
coordinated with the start of the upload.

This setup has other implications. When the Uno is connected to either a
computer running Mac OS X or Linux, it resets each time a connection is made to it
from software (via USB). For the following half-second or so, the bootloader is
running on the Uno. While it is programmed to ignore malformed data (i.e. anything
besides an upload of new code), it will intercept the first few bytes of data sent to
the board after a connection is opened. If a sketch running on the board receives one-
time configuration or other data when it first starts, make sure that the software with
which it communicates waits a second after opening the connection and before
sending this data.

The Uno contains a trace that can be cut to disable the auto-reset. The pads on
either side of the trace can be soldered together to re-enable it. It's labeled "RESET-
EN". You may also be able to disable the auto-reset by connecting a 110 ohm resistor
from 5V to the reset line; see this forum thread for details.
USB OVERCURRENT PROTECTION

The Arduino Uno has a resettable polyfuse that protects your computer's USB
ports from shorts and overcurrent. Although most computers provide their own
internal protection, the fuse provides an extra layer of protection. If more than 500
mA is applied to the USB port, the fuse will automatically break the connection until
the short or overload is removed.

PHYSICAL CHARACTERISTICS

The maximum length and width of the Uno PCB are 2.7 and 2.1 inches
respectively, with the USB connector and power jack extending beyond the former
dimension. Four screw holes allow the board to be attached to a surface or case. Note
that the distance between digital pins 7 and 8 is 160 mil (0.16"), not an even multiple
of the 100 mil spacing of the other pins

You might also like