RTD and thermocouple circuits, with millivolt calculations

This worksheet and all related files are licensed under the Creative Commons Attribution License,
version 1.0. To view a copy of this license, visit http://creativecommons.org/licenses/by/1.0/, or send a
letter to Creative Commons, 559 Nathan Abbott Way, Stanford, California 94305, USA. The terms and
conditions of this license allow for free copying, distribution, and/or modification of all licensed works by
the general public.

1
 Questions
Question 1
Calculate the voltage across the bridge (VAB ) at the following RTD temperatures, assuming a 604 Ω
nickel-iron RTD with an alpha value of 0.00518:

1k5 4k7

+ A B
22 mV −

RTD 2k2

• T = 0 o C ; VAB = millivolts

• T = 81 o C ; VAB = millivolts

• T = -45 o C ; VAB = millivolts

• T = 320 o F ; VAB = millivolts

file i00600

Question 2
Suppose you need to determine the temperature of a fluid inside a pipe. Installed in this pipe is a 2-wire
100 Ω RTD inside a thermowell, not connected to a transmitter or any other circuit. You happen to have a
multimeter with you to measure resistance at the RTD leads.
Touching the two test leads of your multimeter together, you measure 0.3 Ω. Then, connecting those
same leads to the RTD’s wires, you measure 184.6 Ω. You do not happen to have an RTD table with you,
but you do carry a calculator.
Calculate the approximate temperature of the fluid in this pipe, assuming the most common α value
for 100 Ω RTDs.
file i00602

2
Question 3
Determine the temperature of the RTD, given a measured voltage of −59.7 millivolts between test points
C and D in this circuit:

A Rwire = 1.7 Ω C

RTD
R0 = 100 Ω 0.54 mA
α = 0.00392
Rwire = 1.6 Ω
B D

Assume a 100 Ω RTD with α = 0.00392.

file i00166

Question 4
Determine the temperature of the RTD, given a measured voltage of 89.2 millivolts between test points
C and D, and 88.7 millivolts between test points E and D:

A Rwire = unknown C

RTD E
Rwire = unknown
R0 = 100 Ω 0.41 mA
α = 0.00385

B Rwire = unknown D

Assume a 100 Ω RTD with α = 0.00385, and all wire resistances to be equal to each other.
file i00601

3
Question 5
Suppose you need to measure the temperature of an operating oven using nothing but a 1000 Ω RTD
(α = 0.00385), a 1.75 kΩ precision resistor, and a battery of unknown voltage:

1.75 kΩ
precision resistor

-
+

Wht Red V A
Wht Red

V A
1 kΩ RTD OFF

α = 0.00385
A COM

Oven

Turning the switch on, you measure 1.32 volts across the resistor and 1.22 volts across the RTD. Calculate
the oven temperature based on these measurements, and also explain why it is important to quickly take
these measurements once the switch is turned on.
file i00632

4
Question 6
Determine the temperature of the RTD, given VCD = 140.5 millivolts and VEF = 140.1 millivolts:

A Rwire = unknown C

RTD E
Rwire = unknown
R0 = 1 kΩ Rwire = unknown 0.12 mA
α = 0.00385 F

B Rwire = unknown D

Assume a 1 kΩ RTD with α = 0.00385, and all wire resistances completely unknown (not assumed to
be equal).
file i00631

Question 7
Suppose someone builds a dual-junction thermocouple circuit using type T thermocouple wire (copper
and constantan metals), then measures voltage between the two junctions with a voltmeter:

V A

V A
OFF

A COM

Copper (+) Copper (+)

105 oF 77 oF

Constantan (-) Constantan (-)

Calculate the voltage read by the voltmeter, using a type T thermocouple table to find millivolt potentials
for each of the junctions.
file i03172

5
Question 8
When a type “T” thermocouple (copper/constantan) is connected to a voltmeter made of copper wires,
two active junctions are formed: one at the point of measurement (the measurement junction) and one at
a terminal near the voltmeter (the reference junction). The copper-to-copper junction at the top screw of
the terminal block is of no consequence because it is a junction of identical metals, and as such generates no
thermoelectric voltage:

Field Instrument room

Process Terminal block

Copper Copper Voltmeter
+
- Copper
Constantan

Reference
Measurement junction
junction

The amount of voltage sensed by the voltmeter in this thermocouple circuit is equal to the difference in
voltages produced by the measurement and reference junctions:

Emeter = Emeas − Eref

Now consider a type “J” thermocouple connected to a copper-wire voltmeter. Here we see there are not
two but three active junctions of dissimilar metals:

Field Instrument room

Process Terminal block

Iron Copper Voltmeter
+
- Copper
Constantan

Reference
Measurement Reference junction 2
junction junction 1

Upon first observation it would appear this circuit is more complicated than the type “T” thermocouple
circuit, owing to the existence of the additional dissimilar-metal junction. However, a principle called the
Law of Intermediate Metals allows us to consider the two reference junctions (iron-copper and constantan-
copper) as electrically equivalent to a single reference junction of iron-constantan, such that the type “J”

6
thermocouple circuit becomes just as simple as the type “T” circuit with one measurement junction and one
reference junction in opposition to each other.
Explain what the Law of Intermediate Metals is, and how it may be used to simplify the two active
reference junctions of the type “J” circuit. Also, explain why it is important that the terminal block be
isothermal in nature.
file i03628

Question 9
Suppose someone builds a dual-junction thermocouple circuit using type T thermocouple wire (copper
and constantan metals), then measures voltage in the loop using a voltmeter:

V A

V A
OFF

A COM

Copper (+) Constantan (-)

Copper (+) Constantan (-)
o
59 F
193 oF 102 oF

Constantan (-) Copper (+)

Constantan (-) Copper (+)

71 oF

Calculate the voltage read by the voltmeter, using a type T thermocouple table to find millivolt potentials
for each of the junctions.
file i02948

7
Question 10
Calculate the amount of voltage “seen” by the voltmeter given the following measurement and reference
junction temperatures:

Type B thermocouple
T1

T2

Type B
V A cable
T3
V OFF
A

A COM

• T1 = 589 o F ; T2 = 63 o F ; T3 = 70 o F ; Vmeter = mV

• T1 = 821 o F ; T2 = 69 o F ; T3 = 73 o F ; Vmeter = mV

• T1 = 1524 o F ; T2 = 91 o F ; T3 = 105 o F ; Vmeter = mV

• T1 = 1922 o F ; T2 = 102 o F ; T3 = 135 o F ; Vmeter = mV

file i02947

8
Question 11
Calculate the amount of voltage “seen” by the voltmeter given the following measurement and reference
junction temperatures:

Type E thermocouple
T1

T2

Type EX
V A cable
T3
V OFF
A

A COM

• T1 = 233 o C ; T2 = 31 o C ; T3 = 25 o C ; Vmeter = mV

• T1 = 348 o C ; T2 = 40 o C ; T3 = 16 o C ; Vmeter = mV

• T1 = −161 o C ; T2 = −4 o C ; T3 = 23 o C ; Vmeter = mV

• T1 = 836 o C ; T2 = 34 o C ; T3 = 19 o C ; Vmeter = mV
file i02945

9
Question 12
Suppose three different voltmeters are connected to a thermocouple, with each voltmeter having a
different ambient temperature:

71 oF 85 oF 60 oF

Chromel

Voltmeter Voltmeter Voltmeter

o
1050 F

Alumel

Calculate the amount of voltage registered by each of the three voltmeters, as well as answer the following
questions:
• If a fourth voltmeter were connected to this same thermocouple, would it affect the readings of the other
three?
• If a thermocouple transmitter were connected to this thermocouple, would it affect the readings of the
voltmeters? Would it matter whether or not this transmitter were equipped with reference junction
compensation?
file i00873

Question 13
A type K thermocouple is inserted into a process, with a digital multimeter connected to its terminals.
The ambient temperature at the DMM’s test lead connections is 84 o F. Calculate the thermocouple’s
measurement junction temperature at the following millivolt measurements (rounding to the nearest degree
Fahrenheit):
• 2.55 mV ; T = deg F

• 6.21 mV ; T = deg F

• 10.93 mV ; T = deg F

• 18.83 mV ; T = deg F
file i00390

10
Question 14
A type J thermocouple is inserted into a process, with a digital multimeter connected to its terminals.
The ambient temperature at the DMM’s test lead connections is 17 o C. Calculate the thermocouple’s
measurement junction temperature at the following millivolt measurements (rounding to the nearest degree
Celsius):
• 5.05 mV ; T = deg C

• 17.82 mV ; T = deg C

• 31.44 mV ; T = deg C

• 40.29 mV ; T = deg C
file i00379

Question 15
Suppose you walk up to this thermocouple, installed to measure the temperature of an enclosed process
vessel, and connect a sensitive voltmeter to the terminals at the junction head:

Transmitter
Head Z S

(long length of extension cable) 4-20 mA cable

Blu Red

mV

V A
Process vessel

V A
OFF

Temp = ???
A COM

Determine the process temperature if you read 7.825 millivolts with the voltmeter connected to the
screw terminals inside the thermocouple head. Assume a head temperature of 92 o F.

Suppose at some later time you connected the voltmeter to the transmitter’s input terminals and read
8.332 millivolts. Calculate the process temperature at this time, assuming an ambient temperature of 66 o F
at the transmitter.
file i03972

11
Question 16
Calculate the appropriate millivoltage values and potentiometer resistances to simulate a thermocouple
at the desired temperatures, assuming the ambient temperature at the transmitter is 72 o F and the
transmitter has cold junction compensation enabled:

Transmitter
Z S

4-20 mA cable

(Configured for type J)

510 kΩ

1 kΩ pot
10.000 volts DC
power supply

• Tsimulate = 550 o F ; Vinput = mV ; Rpot = Ω

• Tsimulate = 300 o F ; Vinput = mV ; Rpot = Ω

• Tsimulate = 150 o F ; Vinput = mV ; Rpot = Ω

file i03657

12
Question 17
Calculate the voltage sensed by the analog-to-digital converter inside the temperature transmitter:

Temperature
transmitter 75 oF

Analog-Digital Copper cable Type NX cable

converter

93 oF

Type N thermocouple
o
1847 F

file i00357

13
Question 18
Part of this solar-heating control system uses a dual-thermocouple circuit to compare the temperature
inside the solar collector against the temperature inside the house, preventing the circulation fan from running
if the house is ever warmer than the collector:

Sun

House

Heated air
Fan
Collector 119 oF 68 oF TC

Cold air return

TE TE

Blu Blu Red

TT
Red Red

Answer the following questions about this subsystem:

• Identify the thermocouple type used in this application, and determine whether or not this type is a
good choice.

• Calculate the voltage measured at the input terminals of the transmitter, and also determine whether
or not this transmitter needs to be enabled for reference junction compensation.

• Identify the meaning of the diamond-shaped PID symbol labeled “TC”.

file i00377

14
Question 19
This thermocouple is installed improperly:

Transmitter
o
Head Z S

31 C (long length of extension cable) Red 4-20 mA cable

Red
Yel Yellow-colored jacket Yel

Yel Red
23 oC

Process vessel

592 oC

Identify the nature of the problem, and then calculate the millivoltage seen at the screw terminals of the
temperature transmitter given the temperatures shown. After that, calculate the temperature interpreted
by the transmitter assuming it has cold junction compensation (CJC) enabled.
file i00633

15
 Answers
Answer 1
All answers shown here based on tabulated values for the RTD’s resistance (rather than values calculated
by formula):
• T = 0 o C ; VAB = -0.6989 millivolts

• T = 81 o C ; VAB = 0.9568 millivolts

• T = -45 o C ; VAB = -1.6215 millivolts

• T = 320 o F ; VAB = 2.4831 millivolts

Answer 2
The α value is most likely 0.00385, resulting in a calculated temperature of 218.96 o C or 426.13 o F.

Answer 3
RRT D = 107.256 Ω

T = 65 degrees Fahrenheit (from table)

T = 65.32 degrees Fahrenheit (from formula)

Answer 4
VRT D = 88.2 mV Vwire = 0.5 mV (each current-carrying conductor)

RRT D = 215.12 Ω

T = 309 degrees Celsius (from table)

T = 299.02 degrees Celsius (from formula)

Answer 5
RRT D = 1.617 kΩ

Toven = 160.4 o C = 320.7 o F (calculated from formula, not from a table)

The voltage measurements must be taken very soon after the switch is thrown to avoid measurement
errors due to “self-heating” of the RTD.

Answer 6
VRT D = 140.1 mV

RRT D = 1167.5 Ω

T = 43.5 o C = 110.31 o F (both values calculated from formula, not table)

Answer 7
The voltmeter should read -0.643 millivolts, because the 105 o F junction has a potential of 1.635
millivolts, the 77 o F junction has a potential of 0.992 millivolts, and the two junctions’ voltages are opposing
one another in polarity with the positive terminal of the voltmeter connected to the negative-most copper
wire.

16
Answer 8
The Law of Intermediate Metals tells us that a series chain of dissimilar metal junctions at the same
temperature are electrically equivalent to a single junction comprised of the outer two metals (ignoring all
the intermediate metal types between) at that temperature. Thus, the iron-copper-constantan reference
junction pair is electrically equivalent to a single iron-constantan reference junction, so long as both screw
terminals are at the same temperature (isothermal). This principle renders the meter’s metal type irrelevant.

Answer 9
The voltmeter should read −3.908 millivolts. Counting all the junction voltages (with polarities shown
in reference to whether they match or oppose the meter’s test lead polarity):
• 193 o F junction = −3.789 mV
• 71 o F junction = +0.857 mV
• 102 o F junction = −1.565 mV
• 59 o F junction = +0.589 mV
• Loop total voltage = −3.908 mV
Hint: any junction pushing conventional flow in a counter-clockwise direction is regarded here as a
“positive” figure. Any junction pushing in a clockwise direction is regarded as a “negative” figure.
The last junction (at 59 o F) may be treated as a single copper-constantan junction because the metal type
of the meter’s test leads acts as an intermediate metal. The fact that both the copper-testlead and constantan-
testlead junctions are at the same temperature allows us to disregard the test lead metal altogether and treat
it as a single copper-constantan junction at 59 o F.

Answer 10
All answers based on ITS-90 thermocouple table values:
• T1 = 589 o F ; T2 = 63 o F ; T3 = 70 o F ; Vmeter = 0.463 mV

• T1 = 821 o F ; T2 = 69 o F ; T3 = 73 o F ; Vmeter = 0.953 mV

• T1 = 1524 o F ; T2 = 91 o F ; T3 = 105 o F ; Vmeter = 3.378 mV

• T1 = 1922 o F ; T2 = 102 o F ; T3 = 135 o F ; Vmeter = 5.294 mV

Note: all temperatures at T2 are irrelevant because this is a junction between similar metals (type B
wires connecting to corresponding type B wires). The reference (cold) junction is where the type B wires
connect to copper, at temperature T3 .

Answer 11
All answers based on ITS-90 thermocouple table values:
• T1 = 233 o C ; T2 = 31 o C ; T3 = 25 o C ; Vmeter = 14.395 mV

• T1 = 348 o C ; T2 = 40 o C ; T3 = 16 o C ; Vmeter = 23.856 mV

• T1 = −161 o C ; T2 = −4 o C ; T3 = 23 o C ; Vmeter = −9.039 mV

• T1 = 836 o C ; T2 = 34 o C ; T3 = 19 o C ; Vmeter = 62.701 mV

Note: all temperatures at T2 are irrelevant because this is a junction between similar metals (type E
wires connecting to corresponding type EX extension wires). The reference (cold) junction is where the type
EX wires connect to copper, at temperature T3 .

17
Answer 12
Each voltmeter forms its own reference junction where the copper wires of each voltmeter connect to
the chromel and alumel thermocouple wires. Each voltmeter’s reference junction produces its own voltage,
opposed in polarity to the voltage of the measurement junction (at 1050 o F). This means we must perform
a separate voltage calculation for each voltmeter based on each meter’s reference junction temperature. An
equivalent schematic diagram shows how the four dissimiar metal junctions relate to one another, and to the
three voltmeters:

Equivalent circuit showing three voltmeters and the measurement junction:

+ V o + V o + V o
− 71 − 85 − 60

+
Vmeas −
Voltmeter Voltmeter Voltmeter

The chromel and alumel wire types identify this as a type K thermocouple, and so we may use a type
K thermocouple table to look up voltages for all four junction temperatures:
• Type K at 1050 o F = 23.439 mV
• Type K at 71 o F = 0.865 mV
• Type K at 85 o F = 1.181 mV
• Type K at 60 o F = 0.619 mV

Since we know the measurement and reference junctions stand opposed to one another in each voltmeter
loop, we may calculate each voltmeter’s reading by subtracting the reference junction’s voltage from the
measurement junction’s voltage for each voltmeter:

Voltage registered by the left-hand voltmeter (at 71 o F):

23.439 mV − 0.865 mV = 22.574 mV

Voltage registered by the center voltmeter (at 85 o F):

23.439 mV − 1.181 mV = 22.258 mV

Voltage registered by the right-hand voltmeter (at 60 o F):

23.439 mV − 0.619 mV = 22.820 mV

The voltage read by each voltmeter is a simple function of Kirchhoff’s Voltage Law, with the
measurement junction and the voltmeter’s reference junction being the only voltage sources in the KVL loop.
Therefore, connection of a fourth voltmeter will have no effect whatsoever on the other three voltmeters.
Likewise, connection of a thermocouple transmitter to this same chromel/alumel wire pair will have no effect
on the voltmeters’ readings, with or without reference junction compensation.

18
Answer 13
All answers based on ITS-90 thermocouple table values:
• 2.55 mV ; T = 195 deg F

• 6.21 mV ; T = 357 deg F

• 10.93 mV ; T = 567 deg F

• 18.83 mV ; T = 904 deg F

Answer 14
All answers based on ITS-90 thermocouple table values:
• 5.05 mV ; T = 112 deg C

• 17.82 mV ; T = 346 deg C

• 31.44 mV ; T = 586 deg C

• 40.29 mV ; T = 732 deg C

19
Answer 15
An equivalent circuit diagram shows the relationships between the thermocouple measurement junction
(in the process), the two reference junctions formed where thermocouple wire meets copper wire, the digital
multimeter, and the temperature transmitter (when the DMM is connected at the head):

Equivalent circuit with digital multimeter (DMM) connected at head:

+ V o + V o
− 92 − 66

+ −
Vprocess − + V
comp
DMM Transmitter
ADC

Tprocess = 388 deg F at 7.825 millivolts (measured at 92 o F head)

Another equivalent circuit diagram shows the relationships between the thermocouple measurement
junction (in the process), the two reference junctions formed where thermocouple wire meets copper wire,
the digital multimeter, and the temperature transmitter (when the DMM is connected at the transmitter):

Equivalent circuit with digital multimeter (DMM) connected at transmitter:

+ V o + V o
− 66 − 66

+ −
Vprocess − + V
comp
DMM Transmitter
ADC

Tprocess = 385 deg F at 8.332 millivolts (measured at 66 o F transmitter terminals)

Answer 16

• Tsimulate = 550 o F ; Vinput = 14.516 mV ; Rpot = 741.39 Ω

• Tsimulate = 300 o F ; Vinput = 6.815 mV ; Rpot = 347.80 Ω

• Tsimulate = 150 o F ; Vinput = 2.278 mV ; Rpot = 116.20 Ω

20
Answer 17
Voltage at ADC: 35.948 millivolts

According to an ITS-90 table for type N thermocouples, the measurement junction will generate 36.577
mV at 1847 o F, while the reference junction (at the NX-copper cable junction) will generate 0.629 mV at 75
o
F. Since we know these two junctions’ voltages are opposed to each other, the voltage seen at the transmitter
terminals will be 35.984 mV.

Answer 18
These are type T thermocouples, sending 1.174 millivolts to the transmitter’s input. Cold junction
compensation (CJC) should not be enabled in the transmitter, because we want to measure the difference in
temperature between the collector and the house, not compensate for one of those thermocouples’ voltages!
The diamond symbol is a logic device – most likely a PLC – used for on/off control of the fan.

Answer 19
The extension wire has been connected “backwards” to the thermocouple. Yellow should connect to
yellow, and red to red!

Seeing how the four junctions’ voltages interact is best done by drawing the circuit with each junction
explicitly labeled as to polarity. You will see that the process and reference (transmitter) junctions are aiding
each other, and the two junctions formed at the head are opposing the first two (but aiding each other). The
formula for calculating voltage at the transmitter screw terminals then becomes:

Vterminals = V592o C + V23o C − V31o C − V31o C

Vterminals = 24.565 mV + 0.919 mV − 1.244 mV − 1.244 mV

Vterminals = 22.996 mV
If the transmitter has CJC enabled, it will add 0.919 mV to compensate for the reference junction,
making the interpreted (measurement junction) voltage equal to 23.915 mV. This equates to 577 o C, which
is substantially cooler than the real process temperature.

21