Scribd Logo
Upload

Welcome to Scribd!

  • 326 views

    Masterprotect 1815: A Non-Toxic, Flexible High Build, Epoxy Polysulfide Coating

    Uploaded by

    EngTamer
    MasterProtect 1815

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Masterprotect 1815: A Non-Toxic, Flexible High Build, Epoxy Polysulfide Coating

    Uploaded by

    EngTamer
    326 views3 pages
    MasterProtect 1815

    Original Title

    MasterProtect 1815

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    MasterProtect 1815

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    326 views3 pages

    Masterprotect 1815: A Non-Toxic, Flexible High Build, Epoxy Polysulfide Coating

    Uploaded by

    EngTamer
    MasterProtect 1815

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 3

    MasterProtect® 1815

    A non-toxic, flexible high build, epoxy polysulfide coating

    DESCRIPTION TYPICAL PROPERTIES


    MasterProtect 1815 is a protective flexible high
    build epoxy polysulfide resin coating specifically Volume Solids 100%
    developed to protect concrete and steel from Mixed Density at 25°C 1.286 kg/l
    contact with aggressive chemicals, oils, mild acids, Pot Life at 25°C 45 min
    solvents and has a broad spectrum of chemical Tack free time at 25°C 6h
    resistance. Supplied as a two-pack system, Full cure at 25°C 7 days
    comprising pigmented base and a hardener, it Inter-coat time at 25°C 9h
    requires only on site mixing to produce an easily Tensile strength at 7 days 24 MPa
    applied decorative and chemically resistant finish. ASTM D638
    Elongation at 7 days 4%
    PRIMARY USES ASTM D638
    For the internal protection of concrete or metal Hardness (Shore D) 82
    tanks containing sewage, sludge, certain ASTM D2240
    chemicals, oils and fuel. Contact your BASF U/V resistant (500h Xenon Resistant
    representative for further advice. Arc)
    As an impervious, resilient and chemically ASTM G53-58
    resistant floor or wall coating and as a gas and Adhesion to steel Excellent
    vapour barrier. Adhesion to concrete Concrete failure
    As a protective and decorative coating in
    laboratories, abattoirs, etc. Other usage areas APPLICATION PROCEDURE
    include oil refineries, paper mills, power stations,
    marine applications, garages, hospitals, hangars
    and most liquid containment areas. SURFACE PREPARATION:
    Surfaces must be clean and dry. Use suitable
    APPEARANCE AND FINISH methods to remove dirt, dust, oil and all other
    High gloss, heavy bodied, ultra dense surface. forms of contamination that could interface with
    Hygienic and easily cleaned. Standard colours are the adhesion of the coating.
    silver grey and window grey.
    CONCRETE:
    ADVANTAGES Concrete must be cured for 28 days. Mechanically
    surface profile the substrate to CSP3 as described
    • Superior chemical resistance
    by the International Concrete Repair Institute.
    • Waterproof and protective
    Voids and pinholes must be repaired with suitable
    • Durable products from the MasterBrace range. Porous
    • UV resistant concrete should be primed with
    • Easily applied by brush or roller MasterSeal P 659.
    • Flexible
    • Tough
    STEEL:
    Prepare to SSPC-SP6. Surface profile 50 – 75
    PACKAGING
    micron. Do not allow surface to re-oxide before
    MasterProtect 1815 is supplied in 4L & 10 Ltrs application of MasterProtect 1815.
    units.
    MasterProtect® 1815
    MIXING: CHEMICAL RESISTANCE
    MasterProtect 1815 is supplied in two pre- MasterProtect 1815 is resistant to the following
    weighed components, base and reactor. No typically encountered chemicals:
    additions or omissions are required. Add reactor • Chlorine Water – 50ppm
    contents to the base component and mix • Deionised Water
    thoroughly for at least 3 minutes using a slow • Gasoline
    speed drill fitted with a suitable mixing paddle until • Diesel fuel
    a uniform streak free colour is achieved. • Phosphoric Acid 20%
    • Vegetable Oil
    APPLICATION • Sodium Chloride Saturated
    MasterProtect 1815 coating can be applied using • Hydrochloric Acid 5%
    good quality rollers or short haired brushes or by • Sulfuric Acid 10%
    airless spray. MasterProtect 1815 should be • Calcium Hydroxide Saturated
    applied in two coats of contrasting colours to • Isopropanol
    ensure complete coverage free of holidays • Sodium Hydroxide 50%
    If the application is delayed more than 16 hours at • Nitric Acid 20%
    40°C or 36 hours at 20°C after the previous coat • Acetic Acid 10%
    (the higher the ambient temperature, the shorter
    • Lactic Acid 10%
    the maximum period), then the previous coat must
    • Ammonium Hydroxide 30%
    be thoroughly abraded to give an adequate
    mechanical key and solvent wiped. • Formaldehyde 37%

    APPLICATION TEMPERATURE: EQUIPMENT CARE


    The quality of the final coating is dependent on the All equipment must be cleaned immediately after
    substrate and the material temperatures. A use with MasterTop Thinner No. 2. Similar
    substrate temperature of min. +14°C and max. cleaning procedures should be adopted for break
    +30°C is required. Prior to application the optimal periods exceeding 15 minutes duration.
    material temperature is +20°C to +25°C.
    SPECIFICATION CLAUSE
    AIRLESS SPRAY: Where indicated, apply MasterProtect 1815
    For application by airless spray, use a 45:1 or protective epoxy polysulfide coating as
    higher ratio pump, minimum 9mm dia. hoses and manufactured by BASF, or similar approved to the
    HD tip 19-23 thou. following specification:
    Composition: Two component, non-toxic,
    pigmented epoxy polysulfide
    OVERCOATING resin based compound.
    Where areas need to be overcoated due to Coverage: Two coats at 0.25L/m²/coat.
    damage etc. it is important that the areas to be Dry film thickness: 500 microns
    treated are well abraded using a stiff rotary wire
    brush or coarse sand paper to give an adequate
    STORAGE
    key. Completely strip off any unsound coating and
    proceed with overcoating as for new work. Store under cover out of direct sunlight and protect
    from extremes of temperature. In tropical climates
    the product must be stored in an air conditioned
    environment. Failure to comply with the
    recommended storage conditions may result in
    premature deterioration of the product or
    packaging. For specific storage advice, consult
    BASF's Technical Services Department.
    MasterProtect® 1815
    SAFETY PRECAUTIONS
    As with all chemical products, care should be
    taken during use and storage to avoid contact with
    eyes mouth, skin and foodstuffs. Treat splashes to
    eyes and skin immediately. If accidentally
    ingested, seek immediate medical attention. Keep
    away from children & animals. Reseal containers
    after use. For further information, refer to material
    safety data sheet.

    NOTE
    Field service, where provided, does not constitute
    supervisory responsibility. For additional
    information contact your local BASF
    representative. BASF reserves the right to have
    the true cause of any difficulty determined by
    accepted test methods.

    QUALITY AND CARE


    All BASF Products are manufactured under a
    management system independently certified to
    conform to the requirements of the quality,
    environmental and occupational health and safety
    standards of ISO 9001 and BASF ESHQ
    recommendations.

    * Properties listed are based on laboratory controlled tests.

    ® = Registered trademark of the BASF-Group in many countries.

    BASF_CC-UAE/Pr_1815_09_10/v1/09_14-rev-04-2017
    The technical information and application advice given in this BASF publication are based on the present state of
    STATEMENT OF our best scientific and practical knowledge. As the information herein is of a general nature, no assumption can be
    RESPONSIBILITY made as to a product's suitability for a particular use or application and no warranty as to its accuracy, reliability or
    completeness either expressed or implied is given other than those required by law. The user is responsible for
    checking the suitability of products for their intended use.

    Field service where provided does not constitute supervisory responsibility. Suggestions made by
    NOTE BASF either orally or in writing may be followed, modified or rejected by the owner, engineer or contractor since
    they, and not BASF, are responsible for carrying out procedures appropriate to a specific application.

    Saudi BASF for Building Materials Co. Ltd.


    P.O. Box 1884, Al Khobar, KSA
    Tel: +966 13 8538600, Fax: +966 13 8328671
    www.master-builders-solutions.sa

    You might also like