WARNING AND OPERATING INSTRUCTIONS

FOR USING THE LOAD MOMENT INDICATOR (AML-C)

1. When operating crane on outriggers: When a load is lifted in the front position and then swung
Set P.T.O. switch to "ON". to the side area, make sure the value of the LOAD
Press the outrigger mode select key to register for the MOMENT INDICATOR(AML-C) is below the 360o lifting
outrigger operation. Press the register key, then the outrigger capacity.
mode indicative symbol changes from flashing to a solid light. (2) For creep operation.
Press the lift mode select key to select the lift status that The creep capacities are attainable only when boom is
corresponds to the actual boom configuration. in the straight forward position of chassis and the over
Each time the lift mode select key is pressed, the status changes. front position symbol is on. If boom is not in the straight
Press the register key to register the lift status, then the lift forward position of chassis , never lift load.
indicative symbol changes from flashing to a solid light.
when mounting and stowing jib, select the jib set status.
(the jib state indicative symbol will be flashing.)
2. When operating crane on rubber:
3.

4.
A swing does not automatically stop even if the crane
becomes overloaded.
During crane operation, make sure that the displays on front
panel are in accordance with actual operating conditions.
GR-1000XL-2
Set P.T.O. switch to "ON". 5. The displayed values of LOAD MOMENT INDICATOR
Press the outrigger mode select key. The on-tire mode (AML-C) are based on freely suspended loads and make no
indicative symbol comes on. Each time the outrigger mode allowance for such factors as the effect of wind, sudden 100 Ton Capacity (90.7 Metric Tons)
select key is pressed the status changes. Select the creep stopping of loads, supporting surface conditions, inflation of
operation, the on-tire mode indicative symbol flicker. tire, operating speed, side loads, etc.
Press the lift mode select key to register the boom or single top
lift.
For safe operation, it is recommended when extending and
lowering boom or swinging, lifting loads shall be
HYDRAULIC ROUGH TERRAIN CRANE
However, pay attention to the following. appropriately reduced.
(1) For stationary operation. 6. LOAD MOMENT INDICATOR (AML-C) is intended as an aid
The front capacities are attainable only when the over front to the operator. Under no condition should it be relied upon
position symbol comes on. When the boom is more than to replace use of capacity charts and operating instruction. DIMENSIONS
2 degrees from centered over front of chassis, 360 o Sole reliance upon LOAD MOMENT INDICATOR (AML-C)
capacities are in effect. aids in place of good operating practice can cause an
accident. The operator must exercise caution to assure
safety.

GR-1000XL Axle weight distribution chart

Pounds Kilograms
GVW Front Rear GVW Front Rear
Base machine
115,235 57,300 57,935 52,270 25,990 26,280
Remove: 1. 7.3ton(6.6metric ton) hook ball -360 -515 155 -164 -233 69
2. 100ton(90.7metric ton) hook block -1,900 -3,665 1,765 -862 -1,664 802
3. Top jib -740 -990 250 -336 -450 114
4. Base jib -1,910 -3,755 1,845 -867 -1,704 837
5. Auxiliary lifting sheave -110 -330 220 -50 -149 99
6. Removable Counterweight -22,000 9,350 -31,350 -9,979 4,240 -14,219
(with Auxiliary Hoist & wire rope)

TADANO AMERICA CORPORATION Note : Dimension is with boom angle at -1.5 degree.
4242 West Greens Road
Houston, Texas 77066 U.S.A.
PHONE: (281) 869-0030 EXT. 315
GENERAL DIMENSIONS
FAX: (281) 869-0040
Parts Hotline: (281) 869-0033 (29.5 X 25 Tires)
Service Hotline: (281) 869-5925 Feet Meters
Web site: www.tadanoamerica.com Turning radius
E-mail: [email protected] 4 wheel steer 22' 3-3/4" 6.8
Form No. TAC-GR-1000-2-00101-FCTW-110210 2 wheel steer 39' 1/2" 11.9
Tail swing of counterweight 13' 8-15/16" 4.19
16
16 Specifications are subject to change without notice.
CRANE SPECIFICATIONS GR-1000XL RATED LIFTING CAPACITIES (IN POUNDS)
BOOM WIRE ROPE - Non-rotating 3/4"(19mm) 7X35 class. ON RUBBER
Five section full power synchronized telescoping boom, Breaking Strength 72,800lbs(33,000kg) A Stationary Creep
Over Front 360o Rotation Over Front
39.4'~154.2' (12.0m~47.0m), of round box construction
39.4' 68.1' 96.8' 39.4' 68.1' 96.8' 39.4' 68.1' 96.8'
with seven sheaves, 17-5/16" (0.44m) root diameter, at boom head. HOOK BLOCKS B C (12m) C (20.8m) C (29.5m) C (12m) C (20.8m) C (29.5m) C (12m) C (20.8m) C (29.5m)
The synchronization system consists of two telescope cylinders, 100 ton (90.7 metric ton)-8sheaves with swivel hook and safety latch. 12' 66 60,000 66 38,000 66 45,000
an extension cable and retraction cable. Hydraulic cylinder fitted 7.3 ton (6.6 metric ton) - Weighted hook with swivel and safety latch. 15' 61 49,600 61 28,500 61 36,600
with holding valve. Two easily removable wire rope guards, rope 20' 52 37,500 70 35,000 52 17,500 70 20,000 52 26,800 70 29,200
25' 41 28,500 65 29,500 74 28,500 40 10,400 65 14,000 73 14,000 40 20,500 65 22,800 74 23,400
dead end provided on both sides of boom head. Boom telescope 30' 25 21,500 60 24,000 71 24,000 25 6,500 60 9,500 70 10,000 25 15,600 60 18,200 71 18,900
sections are supported by wear pads both vertically and horizontally. HYDRAULIC SYSTEM 35' 55 19,200 67 19,500 55 6,500 67 7,400 55 14,800 67 15,500
Extension speed 114.8 in 160 seconds. 40' 49 15,200 64 16,000 49 4,500 63 5,400 49 12,000 64 12,900
PUMPS - Two variable piston pumps for crane functions. 45' 43 12,200 60 13,000 43 3,000 60 3,900 43 9,800 60 10,600
BOOM ELEVATION - By a double acting hydraulic cylinder with Tandem gear pump for steering, swing and optional equipment. 50' 36 9,700 57 10,600 36 1,800 56 2,700 36 7,900 57 8,900
o o 55' 27 8,000 53 8,800 53 1,700 27 6,500 53 7,300
holding valve. Elevation -1.5 ~80.5 , combination controls for hand Powered by carrier engine. Pump disconnect for crane is 60' 13 6,500 49 7,400 13 5,200 49 6,100
or foot operation. Boom angle indicator. engaged/ disengaged by rotary switch from operator's cab. 65' 45 6,100 44 5,000
Automatic speed reduction and soft stop function. 70' 40 5,000 40 4,100
o o
Boom raising speed 20 to 60 in 46 sec. CONTROL VALVES - Multiple valves actuated by pilot pressure 75' 35 4,100 34 3,200
80' 28 3,400 28 2,500
with integral pressure relief valves.
o o o 85' 20 2,700
JIB - Two stage bi-fold lattice type with 3.5 , 25 or 45 offset (tilt type). D 0 0 28 45 0
Single sheave, 15-5/8"(0.396m) root diameter, at the head of both RESERVOIR - 222 gallon (840 lit.) capacity. External sight level Telescoping conditions (%)
jib sections. Stored alongside base boom section. Jib length is gauge. Tele.
I, II II II I, II II II I, II II II
mode
33.2' (10.1m) or 58.1' (17.7m). Assistant cylinders for mounting 2nd boom 0 0 0 0 0 0 0 0 0
and stowing, controlled at right side of superstructure. FILTRATION - BETA10=10 return filter, full flow with bypass 3rd boom 0 33 66 0 33 66 0 33 66
Self stowing jib mounting pins. protection, located inside of hydraulic reservoir. Accessible for 4th boom 0 33 66 0 33 66 0 33 66
easy replacement. Top boom 0 33 66 0 33 66 0 33 66
AUXILIARY LIFTING SHEAVE (SINGLE TOP)
LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE ON RUBBER OPERATION
Single sheave, 15-5/8"(0.396m) root diameter. Mounted to main OIL COOLER - Air cooled fan type.
A Stationary Creep
boom head for single line work (stowable). Over Front Over Front
360o Rotation
39.4' 68.1' 96.8' 39.4' 39.4' 68.1' 96.8'
ANTI-TWO BLOCK - Pendant type over-winding cut out device CAB AND CONTROLS C B (12m) B (20.8m) B (29.5m) B (12m) B (12m) B (20.8m) B (29.5m)
with audio-visual (FAILURE lamp/BUZZER) warning system. 0 32.2' 19,300 60.8' 6,300 89.1' 2,100 32.2' 5,100 32.2' 14,100 60.8' 5,000 89.1' 1,400
Both crane and drive operations can be performed from one cab A :Boom length in feet
SWING mounted on rotating superstructure. B :Load radius in feet
Hydraulic axial piston motor through planetary swing speed C :Loaded boom angle (o)
o
reducer. Continuous 360 full circle swing on ball bearing turn Left side, 1 man type, steel construction with sliding door access D :Minimum boom angle (o) for indicated length (no load)
-1
table at 1.5min {rpm}. Equipped with manually locked/released and safety glass windows opening at side. Door window is
o NOTE: The lifting capacity data stored in the LOAD MOMENT INDICATOR (AML-C) is based
swing brake. A 360 positive swing lock for pick and carry and travel powered control. Windshield glass window and roof glass window
on the standard number of parts of line listed in the chart.
modes, manually engaged in cab. Twin swing system: Free swing are shatter-resistant. Tilt-telescoping steering wheel. Adjustable Standard number of parts of line for rubber operation should be according to the
or lock swing controlled by selector switch on front console. control lever stands for swing, boom hoist, boom telescoping, following table.
auxiliary hoist and main hoist. Control lever stands can change
HOIST neutral positions and tilt for easy access to cab. 3 way adjustable Boom length in feet 39.4' 39.4' to 96.8' Single top
(meters) (12m) (12m to 29.5m) Jib
operator's seat with high back, headrest and armrest. Engine Number of parts of line 6 4 1
MAIN HOIST - Variable speed type with grooved drum driven by throttle knob. Foot operated controls: boom elevating,
hydraulic axial piston motor through speed reducer. Power load boom telescoping, service brake and engine throttle.
lowering and raising. Equipped with automatic brake (neutral brake) Hot water cab heater and air conditioning.
and counterbalance valve. Controlled independently of auxiliary hoist. WARNING AND OPERATING INSTRUCTIONS
Equipped with cable follower and drum rotation indicator. Dash-mounted engine start/stop, monitor lamps, cigarette lighter,
drive selector switch, parking brake switch, steering mode FOR ON RUBBER LIFTING CAPACITIES
DRUM - Grooved 14-1/4"(0.362m) root diameter x 23-5/8"(0.6m) select switch, power window switch, pump engaged/disengaged
wide. Wire rope: 820' of 3/4"diameter rope (250m of 19mm). switch, swing brake switch, telescoping/auxiliary hoist select 1. Rated lifting capacities on rubber are in pounds and do not exceed 6. Over front operation shall be performed within two degrees in front of
75 % of tipping loads as determined by SAE J765-Crane Stability chassis.
Drum capacity: 997' (304m) 7 layers. Maximum single line pull: switch, outrigger controls, free swing / lock swing selector switch, Test Code. 7. On rubber lifting with "jib" is not permitted. Maximum permissible
1st layer 21,550 lbs (9,770kg). Maximum permissible line pull eco mode switch, high speed hoist (main/aux) switch and ashtray. 2. Rated lifting capacities shown in the chart are based on condition boom length is 96.8 ft. (29.5m).
wire strength: 14,600 lbs (6,600kg). that crane is set on firm level surfaces with axle oscillation lockout 8. When making lift on rubber stationary, set parking brake.
applied. Those above bold lines are based on tire capacity and 9. For creep operation, boom must be centered over front of machine,
AUXILIARY HOIST - Variable speed type with grooved drum driven Instruments - Torque converter oil temperature, engine water those below, on crane stability. They are based on actual load swing lock engaged, and load restrained from swinging. Travel slowly
radius increased by tire deformation and boom deflection. and keep the lifted load as close to the ground as possible, and
by hydraulic axial piston motor through speed reducer. Power load temperature, air pressure, fuel, speedometer, tachometer, 3. If the axle oscillation lockout cylinders contain air, the axle will not especially avoid any abrupt steering, accelerating or braking.
lowering and raising. Equipped with automatic brake (neutral brake) hour meter and odometer / tripmeter. Hydraulic oil pressure is be locked completely and rated lifting capacities may not be 10. Do not operate the crane while carrying the load.
and counterbalance valve. Controlled independently of main hoist. monitored and displayed on the AML-C display panel. obtainable. Bleed the cylinders according to the operation safety 11. Creep is motion for crane not to travel more than 200 ft. (60 m) in any
Equipped with cable follower and drum rotation indicator. and maintenance manual. 30 minute period and to travel at the speed of less than 1 mph
4. Rated lifting capacities are based on proper tire inflation, capacity (1.6km/h).
and condition. Damaged tires are hazardous to safe operation of 12. For creep operation, choose the driv e mode and proper gear
DRUM - Grooved 14-1/4"(0.362m) root diameter x 23-5/8"(0.6m) crane. according to the road or working condition.
wide. Wire rope: 456' of 3/4"diameter rope (139m of 19mm). 5. Tires shall be inflated to correct air pressure.
Drum capacity: 997' (304m) 7 layers. Maximum single line pull: Tires Air Pressure
1st layer 21,550 lbs (9,770kg). Maximum permissible line pull 29.5-25 34PR 57 psi (4.0 kgf/cm2)
wire strength: 14,600 lbs (6,600kg).

2 15
2 15
WARNING AND OPERATING INSTRUCTIONS Tadano electronic LOAD MOMENT INDICATOR system TADANO AML-C monitors outrigger extended length and
(AML-C) including: automatically programs the corresponding "RATED LIFTING
FOR LIFTING CAPACITIES Control lever lockout function CAPACITIES" table
Boom position indicator
GENERAL Outrigger state indicator Operator's right hand console includes transmission gear
1. RATED LIFTING CAPACITIES apply only to the machine as 9. When boom length is between values listed, refer to the Boom angle / boom length / jib offset angle / jib length / load selector and sight level bubble. Upper console includes
originally manufactured and normally equipped by TADANO rated lifting capacities of the next longer and next shorter radius / rated lifting capacities / actual loads read out working light switch, roof washer and wiper switch
LTD. Modifications to the machine or use of optional booms for the same radius. The lesser of the two rated lifting Ratio of actual load moment to rated load moment emergency outrigger set up key switch,
equipment other than that specified can result in a reduction capacities shall be used. indication jib equipped/removed select switch, eco mode switch,
of capacity. 10. When making lifts at a load radius not shown, use the next Automatic Speed Reduction and Soft Stop function high speed hoist (main / aux) switch,
2. Hydraulic cranes can be hazardous if improperly longer radius to determine allowable capacity. on boom elevation and swing boom emergency telescoping switch (2nd and 3rd/4th/top)
operated or maintained. Operation and maintenance of this 11. Load per line should not exceed 14,600 lbs. (6,600kg) for Working condition register switch and air conditioning control switch. Swing lock lever.
machine must be in compliance with information in the main hoist and auxiliary hoist.
Load radius / boom angle / tip height / swing range
Operation and Maintenance Manual supplied with 12. Check the actual number of parts of line with LOAD MOMENT
preset function NOTE: Each crane motion speed is based on unladen
the crane. If this manual is missing, order a replacement INDICATOR (AML-C) before operation. Maximum lifting
through the distributor. capacity is restricted by the number of parts of line of LOAD External warning lamp conditions.
3. The operator and other personnel associated with this MOMENT INDICATOR (AML-C). Limited capacity is as Tare function
machine shall fully acquaint themselves with the latest determined from the formula, Single line pull for main hoist Fuel consumption monitor
OSHA 29 CFR Part 1926 crane safety standards. 14,600 lbs.(6,600kg) x number of parts of line. Main hoist / auxiliary hoist select
13. The boom angle before loading should be greater to account Drum rotation indicator (audible and visible type) main and
for deflection. For rated lifting capacities, the loaded boom auxiliary hoist
SET UP angle and the load radius is for reference only.
1. Rated lifting capacities on the load chart are the maximum 14. The 39.4' (12.0m) boom length capacities are based on boom
allowable crane capacities. They are based on the machine
standing level on firm supporting surface under ideal job
fully retracted. If not fully retracted [less than 53.7'(16.38m)
boom length], use the rated lifting capacities for the 53.7' (16.38m) CARRIER SPECIFICATIONS
conditions. Depending on the nature of the supporting boom length.
surface, it may be necessary to have structural supports 15. Extension or retraction of the boom with loads may be TYPE - Rear engine, left hand steering, driving axle 2-way SUSPENSION - Front: Rigid mounted to frame. Rear: Pivot
under the outrigger floats or tires to spread the loads to a attempted within the limits of the RATED LIFTING CAPACITIES. selected type by manual switch, 4x2 front drive, 4x4 front and mounted with hydraulic lockout device.
larger surface. The ability to telescope loads is limited by hydraulic pressure, rear drive.
2. For outrigger operation, outriggers shall be properly extended boom angle, boom length, crane maintenance, etc. BRAKE SYSTEMS - Service: Air over hydraulic disc brakes on
with tires free of supporting surface before operating crane. 16. For lifting capacity of single top, reduce the rated lifting FRAME - High tensile steel, all welded mono-box construction. all 4 wheels. Parking/Emergency: Spring applied-air released
capacities of relevant boom according to a weight reductions brake acting on input shaft of front axle. Auxiliary: Electro-
OPERATION for auxiliary load handling equipment. Capacities of single top TRANSMISSION - Electronically controlled full automatic pneumatic operated exhaust brake.
1. Rated lifting capacities have been tested to and meet shall not exceed 14,600 lbs. (6,600kg) including main hook.
transmission. Torque converter driving full powershift with
minimum requirements of SAE J1063-Cantilevered Boom 17. When base jib or top jib or both jib removing, jib state switch TIRES - 29.5-25 34PR(OR)
driving axle selector. 6 forward and 2 reverse speeds, constant
Crane Structures Method of Test. select removed.
2. Rated lifting capacities do not exceed 85 % of the tipping 18. When erecting and stowing jib, be sure to retain it by hand or by mesh.
3 speeds - high range - 2 wheel drive; 4 wheel drive OUTRIGGERS - Four hydraulic, beam and jack outriggers.
load on outriggers fully extended as determined by SAE other means to prevent its free movement.
J765-Crane Stability Test Code. 19. Use "ANTI-TWO BLOCK" disable switch when erecting and 3 speeds - low range - 4 wheel drive Vertical jack cylinders equipped with integral holding valve. Each
Rated lifting capacities for partially extended outriggers are stowing jib and when stowing hook block. While the switch is outrigger beam and jack is controlled independently from cab.
determined from the formula, Rated Lifting Capacities pushed, the hoist does not stop, even when overwind condition TRAVEL SPEED - 22 mph (36 km/h) Beams extend to 23' 11-3/8" (7.3 m) center-line and retract to
=(Tipping Load - 0.1 x Tip Reaction)/1.25. occurs. within 10' 10-1/2" (3.315 m) overall width with floats. Outrigger
3. Rated lifting capacities above bold lines in the chart are 20. For boom length with 33.2' (10.1m) jib, rated lifting capacities are AXLE - Front: Full floating type, steering and driving axle with jack floats are attached thus eliminating the need of manually
based on crane strength and those below, on its stability. determined by loaded boom angle only in the column headed planetary reduction. Rear: Full floating type, steering and driving attaching and detaching them. Controls and sight bubble located
They are based on actual load radius increased by boom "154.2' (47.0m) boom + 33.2' (10.1m) jib". axle with planetary reduction and non-spin rear differential. in superstructure cab. Four outrigger extension lengths are
deflection. For boom length with 58.1' (17.7 m) jib, rated lifting capacities provided with corresponding "RATED LIFTING CAPACITIES" for
4. The weight of handling device such as hook blocks, slings, are determined by loaded boom angle only in the column STEERING- Hydraulic power steering controlled by steering crane duty in confined areas.
etc., must be considered as part of the load and must be headed "154.2' (47.0m) boom + 58.1' (17.7m) jib". wheel. Four steering modes available: 2 wheel front, 2 wheel Min. Extension 8' 10-5/16"(2.7m) center to center
deducted from the lifting capacities. For angles not shown, use the next lower loaded boom angle rear, 4 wheel coordinated and 4 wheel crab . Mid. Extension 18' 1/2"(5.5m) center to center
5. Rated lifting capacities are based on freely suspended loads to determine allowable capacity. Mid. Extension 21' 11-3/4"(6.7m) center to center
and make no allowance for such factors as the effect of wind, 21. When lifting a load by using jib (aux. hoist) and boom (main
Max. Extension 23' 11-3/8"(7.3m) center to center
sudden stopping of loads, supporting surface conditions, hoist) simultaneously, do the following:
Float size(Diameter) 1' 11- 5/8" (0.6m)
inflation of tires, operating speeds, side loads, etc. Side pull Enter the operation status as jib operation, not as boom
on the boom or jib is extremely dangerous. operation.
6. Rated lifting capacities do not account for wind on lifted load Before starting operation, make sure that mass of load is
or boom. We recommend against working under the condition within rated lifting capacity for jib. ENGINE
Model Mitsubishi 6M60-TLA3B Radiator Fin and tube core, thermostat controlled
that the load is out of control due to a strong wind.During
Type Direct injection diesel Fan, in.(mm) Suction type, 6-blade, 23.6 (600) dia.
boom lift, consider that the rated lifting capacity is reduced by DEFINITIONS No. of cylinders 6 Starting 24 volt
50% when the wind speed is 20mph(9m/s) to 27mph(12m/s); 1. Load Radius: Horizontal distance from a projection of the axis Combustion 4 cycle, turbo charged and after cooled Charging 24 volt system, negative ground
reduced by 70% when the wind speed is 27mph(12m/s) to of rotation to supporting surface before loading to the center of BoreXStroke, in.(mm) 4.646 X 4.528 (118X115) Battery 2-120 amp. Hour
31mph(14m/s).If the wind speed is 31mph(14m/s) or over, the vertical hoist line or tackle with load applied. Displacement, cu. in (liters) 460 (7.54) Compressor, air, CFM(l /min) 29 CFM (830) at 2,600rpm
stop operation. During jib lift, stop operation if the wind speed 2. Loaded Boom Angle: The angle between the boom base Air inlet heater 24 volt preheat Horsepower (kW) Gross 267 (200) at 2,600rpm
is 20mph(9m/s) section and the horizontal, after lifting the rated lifting capacity Air cleaner Dry type, replaceable element Torque, Max. ft-lb (kgm) 579 (80) at 1,400rpm
7. Rated lifting capacities at load radius shall not be exceeded. at the load radius. Oil filter Full flow with replaceable element Capacity, gal.(liters)
Do not tip the crane to determine allowable loads. 3. Working Area: Area measured in a circular arc about the Fuel filter Full flow with replaceable element Cooling water 3.4 (13)
Fuel tank, gal.(liters) 79.2 (300), right side of carrier Lubrication 3.4 ~ 4.0 (13 ~ 15)
8. Do not operate at boom lengths, radii, or boom angle, where centerline of rotation.
Cooling Liquid pressurized, recirculating by-pass Fuel 79.2 (300)
no capacities are shown. Crane may overturn without any 4. Freely Suspended Load: Load hanging free with no direct
load on the hook. external force applied except by the hoist line.
5. Side Load: Horizontal side force applied to the lifted load either
on the ground or in the air.

14 3
14
3
STANDARD EQUIPMENT GR-1000XL RATED LIFTING CAPACITIES (IN POUNDS)
- Five section full power partially synchronized boom - Independently controlled outriggers ON OUTRIGGERS MIN EXTENDED 8' 10-5/16"(2.7m) SPREAD
39.4'~154.2' (12.0 m~47.0 m) - Four outrigger extension positions o
360 ROTATION
- 33.2' or 58.1' (10.1 m or 17.7 m) bi-fold lattice jib (tilt type) - Self-storing outrigger pads A 39.4' 53.7' 68.1'(20.8m) 82.4'(25.1m) 96.8'(29.5m) 111.1'(33.9m) 125.5'(38.3m) 139.8'(42.6m) 154.2'
with 3.5o, 25o or 45o pinned offsets and self storing pins. - Mitsubishi 6M60-TLA3B turbo charged after cooled engine B C (12m) C (16.4m) C C C C C C C C C C C C C (47m)
- Auxiliary lifting sheave (single top) stowable (267HP) with exhaust brake 8' 73 143,900 78 102,700
- Variable speed main hoist with grooved drum, cable follower - Electronic controlled automatic transmission driven 10' 70 94,900 76 93,000 80 90,200 79 40,100
12' 66 66,900 73 65,200 78 63,700 77 40,100
and 820' of 3/4" cable. by torque converter
15' 61 44,700 70 43,400 75 42,000 75 40,100 78 42,500 78 35,500
- Variable speed auxiliary hoist with grooved drum, cable follower - 4 X 4 X 4 drive/steer 20' 52 26,300 64 25,400 70 24,300 70 30,400 74 26,400 74 31,000 77 27,500 77 31,400 79 28,300 79 31,700
and 456' of 3/4" cable. - Non-spin rear differential 25' 41 17,000 57 16,100 65 15,300 65 20,900 70 17,200 70 21,500 74 18,200 74 21,800 76 18,900 76 22,100 78 19,500 78 22,300
- 2-speed hoist - Automatic rear axle oscillation lockout system 30' 25 11,400 50 10,400 60 9,600 60 14,900 66 11,600 66 15,700 70 12,500 70 16,000 73 13,200 73 16,200 75 13,800 76 16,400 78 14,100 78 15,300
- Drum rotation indicator (audible,visible and thumper type) main - 29.5-25 34PR tires 35' 42 6,600 55 5,800 55 10,900 62 7,700 62 11,600 67 8,700 67 12,100 70
9,400 70 12,300 73 9,900 73 12,500 75 10,300 76 11,400 77 10,500
and auxiliary hoist - Disc brakes 40' 33 3,900 49 3,100 49 8,100 58 4,900 58 8,700 63 5,900 9,200 67 6,600
64 68 9,500 70 7,100 71 9,600 73 7,500 73 8,600 75 7,700
- Anti-Two block device (overwind cutout) - Fenders 45' 18 1,800 43 1,100 43 5,900 53 2,800 53 6,500 60 3,700
60 7,000 64 4,500 64 7,300 68 5,000 68 7,500 71 5,400 71 6,500 73 5,600
50' 36 4,300 49 1,100 49 4,900 56 2,100
56 5,300 61 2,800 61 5,600 65 3,300 65 5,800 68 3,700 69 4,800 71 4,000
- Boom angle indicator - Air dryer
55' 27 2,900 44 3,500 53 3,900 58 1,500 58 4,200 63 2,000 63 4,400 66 2,400 66 3,500 69 2,700
- Tadano electronic load moment indicator system (AML-C) - Water separator with filter(high filtration)
60' 13 1,900 38 2,400 49 2,800 55 3,100 60 3,300 64 1,300 64 2,300 67 1,500
- Outrigger extension length detector - Engine over-run alarm 65' 31 1,500 44 1,900 52 2,200 57 2,300 62 1,400
- Electronic crane monitoring system - Back-up alarm 70' 40 1,100 48 1,400 54 1,500
o
- Tadano twin swing system and 360 positive swing lock - Low oil pressure/high water temp. warning device (visual) D 0 28 0 44 5 49 35 55 45 58 52 62 57 65
- Self centering finger control levers with pilot control - Rear steer centering light Telescoping conditions (%)
- Control pedals for boom elevating and boom telescoping - Air cleaner dust indicator Tele.
I, II I I II I II I II I II I II I II I, II
mode
- 3 way adjustable cloth seat with armrests, high back - Full instrumentation package 2nd boom 0 50 100 0 100 0 100 0 100 0 100 0 100 50 100
and seat belt - Complete highway light package 3rd boom 0 0 0 33 16 50 33 66 50 83 66 100 83 100 100
- Tilt-telescoping steering wheel - Tool storage compartment 4th boom 0 0 0 33 16 50 33 66 50 83 66 100 83 100 100
- Tinted safety glass and sun visor - Tire inflation kit Top boom 0 0 0 33 16 50 33 66 50 83 66 100 83 100 100
- Front windshield wiper and washer - 24 volt electric system
- Roof window wiper and washer - 7.3 ton (6.6 metric ton) hook with swivel LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE ON OUTRIGGERS MIN EXTENDED
- Power window (cab door ) - 100 ton (90.7 metric ton) - 8 sheave with swivel hook and 8' 10-5/16"(2.7m)SPREAD 360 o ROTATION
- Rear view mirrors (right and left side) safety latch for 3/4"(19mm) wire rope A 39.4' 53.7' 68.1'
- Mirror for main and auxiliary hoists - Towing hooks-Front and rear C B (12m) B (16.4m) B (20.8m)
0 32.2' 9,200 46.5' 1,300 60.8' 1,700
- Cigarette lighter and ashtray - Lifting eyes
Tele.
- Cab floor mat - Hook block tie down (front bumper) I, II I II
mode
- Pump disconnect in operator's cab - Weighted hook storage compartment
- Hydraulic oil cooler - Halogen head lamp
- Hot water cab heater and air conditioner - Telecommunications terminal (HELLO-NET Owners Site) A :Boom length in feet
- Positive control - Fuel consumption monitor B :Load radius in feet
o
- Quick reeving type bi-fold jib C :Loaded boom angle ( )
o
D :Minimum boom angle ( ) for indicated length (no load)
- Work lights

NOTE:The lifting capacity data stored in the LOAD MOMENT INDICATOR (AML-C) is based on the standard
number of parts of line listed in the chart.
Standard number of parts of line for each boom length should be according to the following table.

HOISTING PERFORMANCE Boom length in feet

(meters)
39.4'
(12m)
39.4' to 68.1'
(12m to 20.8m)
68.1' to 154.2'
(20.8m to 47m)
Single top
Jib
Telescoping mode I, II I II I, II I, II
LINE SPEEDS AND PULLS DRUM WIRE ROPE CAPACITIES
Number of parts of line 16 8 4 4 1
Main or auxiliary hoist - 14'-1/4" (0.362m) drum Main and auxiliary drum grooved lagging
Wire
Layer Line speeds1 Line pulls Available2 rope 3/4" (19mm) wire rope
Low High Low High Rope per layer Total wire rope
layer
F.P.M. m/min F.P.M. m/min Lbs. kgf Lbs. kgf Feet Meters Feet Meters
1st 278 84 387 118 21,550 9,770 15,470 7,020 1 112.2 34.2 112.2 34.2
2nd 302 92 421 128 19,510 8,850 14,010 6,350 2 122.3 37.3 234.5 71.5
3rd 327 99 456 139 17,830 8,090 12,800 5,810 3 132.2 40.3 366.8 111.8
4th 352 107 491 149 16,420 7,450 11,790 5,350 4 142.3 43.4 509.1 155.2
5th 377 115 526 160 15,210 6,900 10,920 4,950 5 152.2 46.4 661.4 201.6
6th 402 122 560 170 14,170 6,430 10,170 4,610 6 162.4 49.5 823.8 251.1
7th3 427 130 595 181 13,260 6,010 9,520 4,320 7 172.5 52.6 996.4 303.7
* Maximum permissible line pull may be affected by wire rope strength.
Wire rope strength (7x35 class) = 14,600lbs (6,600kg)
DRUM DIMENSIONS
1
Line speeds based only on hook block, not loaded. Inch mm
2
Developed by machinery with each layer of wire rope, but not based Root diameter 14-1/4" 362
on rope strength or other limitation in machinery or equipment. Length 23-5/8" 600
3
Seventh layer of wire rope are not recommended Flange diameter 25-7/8" 657
for hoisting operations.

4 13
13
4
 GR-1000XL WORKING RANGE CHART

GR-1000XL RATED LIFTING CAPACITIES (IN POUNDS)

ON OUTRIGGERS MID EXTENDED 18' 1/2"(5.5m) SPREAD
360o ROTATION
154.2' (47.0m) Boom + 33.2' (10.1m) Jib 154.2' (47.0m) Boom + 58.1' (17.7m) Jib
C 3 5o offset 25o offset 45o offset C 3 5o offset 25o offset 45o offset
R W R W R W R W R W R W
80 37.8' 10,800 51.5' 10,800 58.8' 9,400 80 45.8' 6,800 71.7' 6,300 83.5' 5,100
79 41.5' 10,800 55.3' 10,400 62.2' 9,200 79 50.0' 6,800 75.5' 6,200 87.1' 5,100
78 45.2' 10,800 58.6' 10,200 65.7' 9,000 78 54.2' 6,800 79.1' 6,000 90.3' 5,000
77 49.2' 10,800 62.1' 9,900 68.4' 8,800 77 58.5' 6,800 82.7' 5,900 93.3' 5,000
76 52.6' 10,800 65.3' 9,600 71.6' 8,700 76 62.7' 6,800 86.4' 5,800 96.2' 4,900
75 56.3' 10,800 69.0' 9,300 74.5' 8,500 75 66.8' 6,800 90.0' 5,700 99.5' 4,800
73 63.2' 10,100 74.4' 8,300 80.1' 7,600 73 74.6' 6,800 96.7' 5,500 105.0' 4,700
70 71.2' 7,400 82.4' 6,200 87.4' 5,700 70 84.5' 5,200 105.0' 4,200 112.0' 3,800
68 76.6' 6,000 87.3' 5,000 92.0' 4,700 68 90.3' 4,100 109.0' 3,300 117.0' 3,000
65 84.6' 4,300 95.2' 3,700 98.9' 3,500 65 98.8' 2,700 117.0' 2,300 123.0' 2,100
63 90.0' 3,400 100.0' 2,900 103.0' 2,800 63 105.0' 2,000 122.0' 1,700 128.0' 1,600
60 97.6' 2,300 107.0' 2,000 110.0' 1,900 60 113.0' 1,100
58 103.0' 1,700 112.0' 1,400 115.0' 1,400

ON OUTRIGGERS MID EXTENDED 18' 1/2"(5.5m) SPREAD

360o ROTATION
139.8'(42.6m) Boom(telescoping mode II) + 33.2' (10.1m) Jib 139.8'(42.6m) Boom(telescoping mode II) + 58.1' (17.7m) Jib
C 3 5o offset 25o offset 45o offset C 3 5o offset 25o offset 45o offset
R W R W R W R W R W R W
80 32.7' 11,700 45.8' 11,600 53.0' 10,000 80 40.8' 7,300 64.6' 6,500 77.3' 5,200
79 36.4' 11,700 49.0' 11,200 55.8' 9,800 79 44.7' 7,300 67.9' 6,400 80.4' 5,100
78 39.6' 11,700 52.1' 10,900 59.1' 9,600 78 48.7' 7,300 72.0' 6,200 83.5' 5,100
77 43.0' 11,700 55.0' 10,600 61.6' 9,400 77 52.6' 7,300 75.2' 6,100 86.2' 5,000
76 46.4' 11,700 57.7' 10,300 64.1' 9,200 76 56.5' 7,300 78.1' 6,000 89.2' 5,000
75 49.4' 11,700 60.9' 10,100 67.0' 9,100 75 60.0' 7,300 81.8' 5,900 92.4' 5,000
73 55.8' 11,500 67.0' 9,500 72.6' 8,700 73 67.0' 7,300 88.2' 5,700 97.7' 4,900
70 64.6' 10,200 74.9' 8,600 79.7' 7,800 70 78.3' 7,300 97.5' 5,400 105.0' 4,700
68 69.3' 8,500 79.7' 7,300 84.0' 6,700 68 83.8' 6,100 103.0' 5,000 110.0' 4,400
65 76.8' 6,600 86.4' 5,800 90.4' 5,400 65 91.6' 4,600 110.0' 3,900 116.0' 3,400
63 81.8' 5,600 91.1' 4,900 94.7' 4,600 63 97.1' 3,800 114.0' 3,200 120.0' 2,800
60 89.1' 4,300 97.6' 3,800 101.0' 3,600 60 105.0' 2,800 121.0' 2,400 127.0' 2,100
58 93.6' 3,600 102.0' 3,200 105.0' 3,000 58 110.0' 2,200 126.0' 1,900 131.0' 1,700
55 101.0' 2,700 108.0' 2,400 111.0' 2,300 55 118.0' 1,500 133.0' 1,300 137.0' 1,200
53 105.0' 2,200 113.0' 2,000 115.0' 1,900 53 123.0' 1,100
50 111.0' 1,500 119.0' 1,400 120.0' 1,300
48 116.0' 1,100 122.0' 1,000 124.0' 1,000

ON OUTRIGGERS MID EXTENDED 18' 1/2"(5.5m) SPREAD

360o ROTATION
125.5'(38.3m) Boom(telescoping mode I) + 33.2' (10.1m) Jib 125.5'(38.3m)Boom(telescoping mode I) + 58.1' (17.7m) Jib
C 3 5o offset 25o offset 45o offset C 3 5o offset 25o offset 45o offset
R W R W R W R W R W R W
80 30.5' 14,600 43.5' 14,000 50.1' 10,700 80 37.2' 8,800 58.7' 7,000 71.2' 5,200
79 33.3' 14,600 46.0' 13,600 52.6' 10,600 79 41.2' 8,800 61.5' 6,800 73.9' 5,100
78 36.0' 14,600 49.2' 13,300 55.1' 10,500 78 44.8' 8,800 65.4' 6,700 76.8' 5,100
77 39.0' 14,600 51.7' 12,900 57.6' 10,300 77 47.8' 8,800 68.4' 6,500 79.5' 5,000
76 42.6' 14,600 54.1' 12,700 60.1' 10,200 76 51.3' 8,800 70.8' 6,400 82.1' 5,000
75 45.5' 14,600 56.9' 12,400 62.7' 10,100 75 54.9' 8,800 74.3' 6,300 84.9' 5,000
73 51.2' 14,600 62.4' 11,900 67.5' 10,000 73 61.6' 8,800 80.5' 6,100 90.0' 4,900
70 58.2' 11,300 68.9' 9,500 73.7' 8,600 70 71.3' 8,300 88.9' 5,800 97.5' 4,700
68 63.0' 9,500 73.2' 8,100 77.8' 7,400 68 76.1' 6,900 94.0' 5,500 102.0' 4,600
65 69.9' 7,300 79.6' 6,300 83.5' 5,900 65 84.0' 5,200 101.0' 4,200 108.0' 3,900
63 74.5' 6,100 83.7' 5,400 87.5' 5,000 63 89.2' 4,300 105.0' 3,500 112.0' 3,300
60 81.0' 4,700 90.0' 4,200 93.5' 3,900 60 96.6' 3,100 112.0' 2,600 118.0' 2,500
58 85.4' 3,900 93.9' 3,500 97.1' 3,300 58 102.0' 2,500 116.0' 2,100 122.0' 2,000
55 91.8' 2,900 99.7' 2,600 103.0' 2,500 55 108.0' 1,700 123.0' 1,400 128.0' 1,400
53 95.7' 2,300 104.0' 2,100 106.0' 2,000 53 113.0' 1,200 127.0' 1,000 131.0' 1,000
50 102.0' 1,600 109.0' 1,500 111.0' 1,400
48 105.0' 1,100 113.0' 1,100 114.0' 1,000

C :Loaded boom angle (o)

R :Load radius in feet
W :Rated lifting capacity in pounds

12
12
5
GR-1000XL WORKING RANGE CHART

GR-1000XL RATED LIFTING CAPACITIES (IN POUNDS)

ON OUTRIGGERS MID EXTENDED 18' 1/2"(5.5m) SPREAD
o
360 ROTATION
A 39.4' 53.7' 68.1' (20.8m) 82.4' (25.1m) 96.8' (29.5m) 111.1' (33.9m) 125.5' (38.3m) 139.8' (42.6m) 154.2'
B C (12m) C (16.4m) C C C C C C C C C C C C C (47m)
8' 73 191,600 78 102,700
10' 70 164,000 76 102,700 80 90,200 79 40,100
12' 67 142,400 74 102,700 78 90,200 77 40,100
15' 61 113,500 70 102,700 75 89,900 75 40,100 78 42,500 78 35,500
20' 52 75,400 64 73,400 71 67,200 70 40,100 74 42,500 74 35,500 77 40,100 77 33,300 79 35,500 79 32,200
25' 41 48,200 57 46,700 66 45,400 65 40,100 71 42,500 70 35,500 74 40,100 74 33,300 77 35,500 77 32,200 79 33,300 79 28,700
30' 25 33,900 50 32,700 61 31,500 60 35,500 67 33,600 67 35,500 71 34,800 71 33,300 74 35,500 74 30,200 77 33,300 77 26,300 79 26,700 79 24,300
35' 42 23,900 55 23,000 55 28,900 63 24,900 62 29,500 68 26,000 68 29,900 71 26,800 72 27,300 74 27,300 74 24,000 77 26,700 77 24,100 78 20,900
40' 33 18,000 50 17,100 50 22,800 58 19,000 58 23,400 64 20,100 64 23,800 68 20,800 69 24,100 71 21,400 72 22,000 74 21,800 75 22,300 77 20,900
45' 18 13,700 44 12,900 43 18,300 54 14,800 54 19,000 61 15,800 61 19,400 65 16,500 65 19,600 69 17,000 69 19,800 72 17,400 72 18,700 75 17,700
50' 36 9,700 36 14,900 49 11,500 49 15,600 57 12,600 57 16,000 62 13,200 62 16,300 66 13,800 67 16,400 70 14,100 70 15,300 73 14,400
55' 27 7,200 27 12,300 44 8,900 44 13,000 53 10,000 53 13,400 59 10,700 59 13,700 63 11,200 64 13,800 67 11,600 68 12,700 70 11,900
60' 12 5,300 12 10,300 38 6,900 38 10,800 49 7,900 49 11,300 55 8,600 56 11,600 61 9,100 61 11,700 65 9,500 65 10,700 68 9,800
65' 32 5,200 32 9,100 45 6,200 45 9,500 52 6,900 52 9,800 58 7,500 58 10,000 62 7,800 63 9,000 66 8,100
70' 23 3,800 23 7,700 40 4,800 40 8,100 48 5,500 49 8,300 55 6,000 55 8,500 60 6,400 60 7,500 64 6,700
75' 6 2,600 5 6,500 35 3,600 35 6,800 45 4,300 45 7,100 52 4,800 52 7,300 57 5,200 57 6,300 61 5,500
80' 29 2,600 28 5,800 41 3,200 41 6,000 49 3,700 49 6,200 55 4,100 55 5,200 59 4,400
85' 21 1,700 20 4,900 36 2,300 36 5,100 45 2,800 46 5,300 52 3,200 52 4,300 57 3,500
90' 31 1,600 31 4,300 42 2,100 42 4,500 49 2,400 49 3,500 54 2,700
95' 25 3,700 38 1,400 38 3,800 46 1,700 46 2,800 52 2,000
100' 16 3,100 34 3,200 43 1,100 43 2,200 49 1,400
105' 29 2,600 40 1,700
110' 23 2,200 36 1,100
115' 14 1,700
D 0 18 0 29 0 40 27 47
Telescoping conditions (%)
Tele.
I, II I I II I II I II I II I II I II I, II
mode
2nd boom 0 50 100 0 100 0 100 0 100 0 100 0 100 50 100
3rd boom 0 0 0 33 16 50 33 66 50 83 66 100 83 100 100
4th boom 0 0 0 33 16 50 33 66 50 83 66 100 83 100 100
Top boom 0 0 0 33 16 50 33 66 50 83 66 100 83 100 100

LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE ON OUTRIGGERS MID EXTENDED

o
18' 1/2"(5.5m) SPREAD 360 ROTATION
A 39.4' 53.7' 68.1' (20.8m) 82.4' (25.1m) 96.8' (29.5m) 111.1' 125.5'
C B (12m) B (16.4m) B B B B B B B (33.9m) B (38.3m)
0 32.2' 29,200 46.4' 12,600 60.7' 5,000 60.7' 10,000 75.0' 2,600 75.0' 6,500 89.2' 1,100 89.1' 4,300 103.0' 2,800 116.0' 1,500
Tele.
I, II I I II I II I II II II
mode

A :Boom length in feet

B :Load radius in feet
o
C :Loaded boom angle ( )
D :Minimum boom angle (o) for indicated length (no load)

NOTE:The lifting capacity data stored in the LOAD MOMENT INDICATOR (AML-C) is based on the standard
number of parts of line listed in the chart.
Standard number of parts of line for each boom length should be according to the following table.

Boom length in feet 39.4' 39.4' to68.1' 68.1' to 154.2' Single top
(meters) (12m) (12m to20.8m) (20.8m to 47m) Jib
Telescoping mode I, II I II I, II I, II

Number of parts of line 16 8 4 4 1

11
11
6
GR-1000XL RATED LIFTING CAPACITIES (IN POUNDS) GR-1000XL RATED LIFTING CAPACITIES (IN POUNDS)
ON OUTRIGGERS MID EXTENDED 21' 11-3/4"(6.7m) SPREAD
ON OUTRIGGERS FULLY EXTENDED 23' 11-3/8"(7.3m) SPREAD
360o ROTATION o
154.2' (47.0m) Boom + 33.2' (10.1m) Jib 154.2' (47.0m) Boom + 58.1' (17.7m) Jib 360 ROTATION
C 3.5o offset 25o offset 45o offset C 3.5o offset 25o offset 45o offset A 39.4' 53.7' 68.1' (20.8m) 82.4' (25.1m) 96.8' (29.5m) 111.1' (33.9m) 125.5' (38.3m) 139.8' (42.6m) 154.2'
R W R W R W R W R W R W B C (12m) C (16.4m) C C C C C C C C C C C C C (47m)
80 37.8' 10,800 51.5' 10,800 58.8' 9,400 80 45.8' 6,800 71.7' 6,300 83.5' 5,100 8' 73 200,000 78 102,700
79 41.5' 10,800 55.3' 10,400 62.2' 9,200 79 50.0' 6,800 75.5' 6,200 87.1' 5,100
10' 70 180,000 76 102,700 80 90,200 79 40,100
78 45.2' 10,800 58.6' 10,200 65.7' 9,000 78 54.2' 6,800 79.1' 6,000 90.3' 5,000
77 49.2' 10,800 62.1' 9,900 68.4' 8,800 77 58.5' 6,800 82.7' 5,900 93.3' 5,000 12' 67 157,900 74 102,700 78 90,200 77 40,100
76 52.6' 10,800 65.3' 9,600 71.6' 8,700 76 62.7' 6,800 86.4' 5,800 96.2' 4,900 15' 61 132,300 70 102,700 75 89,900 75 40,100 78 42,500 78 35,500
75 56.3' 10,800 69.0' 9,300 74.5' 8,500 75 66.8' 6,800 90.0' 5,700 99.5' 4,800 20' 52 99,700 64 99,100 71 76,100 70 40,100 74 42,500 74 35,500 77 40,100 77 33,300 79 35,500 79 32,200
73 63.5' 10,500 75.2' 8,900 80.5' 8,200 73 74.6' 6,800 96.7' 5,500 105.0' 4,700 25' 41 76,900 58 76,200 66 65,600 65 40,100 71 42,500 70 35,500 74 40,100 74 33,300 77 35,500 77 32,200 79 33,300 79 28,700
70 73.4' 9,600 84.5' 8,300 88.8' 7,700 70 87.2' 6,800 107.0' 5,200 113.0' 4,600
30' 25 50,700 51 57,700 61 56,700 60 40,100 67 42,500 67 35,500 71 40,100 71 33,300 74 35,500 74 30,200 77 33,300 77 26,300 79 26,700 79 24,300
68 79.0' 8,700 89.8' 7,700 94.0' 7,000 68 93.8' 6,300 113.0' 5,100 119.0' 4,500
65 86.7' 6,700 96.9' 6,000 101.0' 5,600 65 102.0' 4,700 120.0' 4,000 125.0' 3,700 35' 43 42,800 56 41,800 55 40,100 63 42,500 63 35,500 68 39,500 68 31,600 72 35,100 72 27,300 74 30,900 74 24,000 77 26,700 77 24,100 78 20,900
63 91.8' 5,600 102.0' 5,100 105.0' 4,700 63 108.0' 3,800 125.0' 3,300 130.0' 3,100 40' 33 33,100 50 32,100 49 36,400 59 34,100 59 35,500 65 34,000 65 29,300 69 32,000 69 24,900 72 28,400 72 22,000 75 25,300 75 22,300 77 20,900
60 99.3' 4,300 109.0' 3,900 112.0' 3,700 60 116.0' 2,800 133.0' 2,400 137.0' 2,300 45' 18 26,200 44 25,400 43 31,100 54 27,300 54 31,800 61 28,300 61 26,500 66 28,000 66 22,900 69 26,100 69 20,200 72 23,500 73 20,700 75 20,700
58 104.0' 3,500 114.0' 3,300 116.0' 3,100 58 121.0' 2,200 138.0' 1,900 141.0' 1,800 50' 37 20,400 36 25,900 49 22,200 49 26,600 57 23,200 58 24,100 63 24,000 63 21,300 67 22,900 67 18,700 70 21,800 71 19,300 73 19,400
55 112.0' 2,600 121.0' 2,400 122.0' 2,300 55 129.0' 1,400 145.0' 1,300 147.0' 1,200
53 116.0' 2,100 125.0' 1,900 126.0' 1,800 53 134.0' 1,000 55' 28 16,600 27 20,900 44 18,400 44 22,600 54 19,300 54 22,200 59 20,100 60 19,600 64 20,100 64 17,400 68 19,600 68 18,000 71 18,100
50 123.0' 1,400 131.0' 1,300 132.0' 1,200 60' 13 13,600 12 15,900 39 15,300 38 19,400 49 16,200 50 19,700 56 17,000 57 18,200 61 17,300 62 16,100 66 17,400 66 16,800 69 16,800
48 128.0' 1,000 65' 32 12,700 32 16,800 45 13,700 45 17,100 53 14,400 53 16,600 58 14,800 59 15,000 63 15,300 64 15,800 67 15,200
70' 24 10,600 23 14,600 40 11,600 41 15,000 49 12,300 50 15,200 56 12,700 56 13,800 61 13,200 61 14,300 65 13,400
75' 7 8,900 5 11,700 35 9,800 35 13,200 45 10,600 46 13,400 53 10,900 53 12,700 58 11,400 59 12,500 62 11,700
ON OUTRIGGERS MID EXTENDED 21' 11-3/4"(6.7m) SPREAD
80' 29 8,300 29 11,600 41 9,100 42 11,900 49 9,500 50 11,700 55 9,900 56 11,000 60 10,200
360o ROTATION
85' 21 7,100 21 10,300 37 7,800 38 10,500 46 8,200 46 10,800 53 8,600 53 9,700 58 8,900
139.8'(42.6m) Boom(telescoping mode II) + 33.2' (10.1m) Jib 139.8'(42.6m) Boom(telescoping mode II) + 58.1' (17.7m) Jib
C C 90' 31 6,600 33 9,400 42 7,000 43 9,600 50 7,500 50 8,600 55 7,700
3.5o offset 25o offset 45o offset 3.5o offset 25o offset 45o offset
R W R W R W R W R W R W 95' 25 5,600 27 8,400 38 6,000 39 8,600 47 6,500 47 7,600 53 6,700
80 32.7' 11,700 45.8' 11,600 53.0' 10,000 80 40.8' 7,300 64.6' 6,500 77.3' 5,200 100' 17 4,800 19 7,500 34 5,200 35 7,700 43 5,600 44 6,700 50 5,900
79 36.4' 11,700 49.0' 11,200 55.8' 9,800 79 44.7' 7,300 67.9' 6,400 80.4' 5,100 105' 29 4,400 30 6,900 40 4,800 41 5,900 47 5,100
78 39.6' 11,700 52.1' 10,900 59.1' 9,600 78 48.7' 7,300 72.0' 6,200 83.5' 5,100
110' 24 3,700 24 6,200 37 4,100 37 5,200 44 4,300
77 43.0' 11,700 55.0' 10,600 61.6' 9,400 77 52.6' 7,300 75.2' 6,100 86.2' 5,000
76 46.4' 11,700 57.7' 10,300 64.1' 9,200 76 56.5' 7,300 78.1' 6,000 89.2' 5,000 115' 15 3,100 15 5,600 33 3,500 32 4,500 41 3,700
75 49.4' 11,700 60.9' 10,100 67.0' 9,100 75 60.0' 7,300 81.8' 5,900 92.4' 5,000 120' 27 2,900 28 4,000 38 3,200
73 55.8' 11,500 67.0' 9,500 72.6' 8,700 73 67.0' 7,300 88.2' 5,700 97.7' 4,900 125' 22 2,400 23 3,500 34 2,600
70 65.1' 10,400 75.1' 8,900 80.1' 8,200 70 78.3' 7,300 97.5' 5,400 105.0' 4,700 130' 14 2,000 14 3,100 30 2,200
68 70.4' 9,700 80.6' 8,400 84.9' 7,800 68 85.2' 7,100 103.0' 5,300 110.0' 4,600
65 78.4' 8,600 88.1' 7,500 91.7' 7,100 65 94.2' 6,200 112.0' 5,100 118.0' 4,600 135' 26 1,800
63 83.7' 7,900 93.0' 7,000 96.4' 6,700 63 99.8' 5,700 117.0' 4,700 123.0' 4,400 D 0 20
60 91.1' 6,600 99.4' 6,000 102.0' 5,600 60 108.0' 4,700 124.0' 4,000 129.0' 3,800 Telescoping conditions (%)
58 95.6' 5,800 104.0' 5,200 106.0' 5,000 58 113.0' 4,000 128.0' 3,400 133.0' 3,300 Tele.
55 102.0' 4,700 110.0' 4,300 112.0' 4,100 55 120.0' 3,100 135.0' 2,700 139.0' 2,600 I, II I I II I II I II I II I II I II I, II
mode
53 107.0' 4,100 114.0' 3,700 116.0' 3,600 53 125.0' 2,600 139.0' 2,300 142.0' 2,200 2nd boom 0 50 100 0 100 0 100 0 100 0 100 0 100 50 100
50 113.0' 3,300 120.0' 3,000 121.0' 2,900 50 132.0' 2,000 145.0' 1,800 147.0' 1,700
3rd boom 0 0 0 33 16 50 33 66 50 83 66 100 83 100 100
48 117.0' 2,800 124.0' 2,600 125.0' 2,600 48 137.0' 1,600 149.0' 1,500 151.0' 1,400
45 123.0' 2,200 129.0' 2,100 129.0' 2,100 45 143.0' 1,200 155.0' 1,000 155.0' 1,000 4th boom 0 0 0 33 16 50 33 66 50 83 66 100 83 100 100
43 127.0' 1,900 132.0' 1,800 Top boom 0 0 0 33 16 50 33 66 50 83 66 100 83 100 100
40 132.0' 1,500 137.0' 1,400
38 136.0' 1,200 140.0' 1,100
LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE ON OUTRIGGERS FULLY EXTENDED
23' 11-3/8"(7.3m) SPREAD 360 o ROTATION
ON OUTRIGGERS MID EXTENDED 21' 11-3/4"(6.7m) SPREAD A 39.4' 53.7' 68.1' (20.8m) 82.4' (25.1m) 96.8' (29.5m) 111.1' (33.9m) 125.5' (38.3m) 139.8' (42.6m)
360o ROTATION C B (12m) B (16.4m) B B B B B B B B B B B B
125.5'(38.3m) Boom(telescoping mode I) + 33.2' (10.1m) Jib 125.5'(38.3m)Boom(telescoping mode I) + 58.1' (17.7m) Jib 0o 32.2' 30,900 46.6' 19,400 60.7' 12,100 60.5' 15,600 75.0' 8,900 75.0' 11,800 89.0' 6,200 89.0' 8,200 102.0' 4,400 103.0' 6,200 117.0' 3,000 116.0' 5,400 131.0' 2,000 130.0' 3,100
C o
3.5 offset o
25 offset o
45 offset C o
3.5 offset o
25 offset o
45 offset Tele.
R W R W R W R W R W R W I, II I I II I II I II I II I II I II
mode
80 30.5' 14,600 43.5' 14,000 50.1' 10,700 80 37.2' 8,800 58.7' 7,000 71.2' 5,200
79 33.3' 14,600 46.0' 13,600 52.6' 10,600 79 41.2' 8,800 61.5' 6,800 73.9' 5,100
78 36.0' 14,600 49.2' 13,300 55.1' 10,500 78 44.8' 8,800 65.4' 6,700 76.8' 5,100
77 39.0' 14,600 51.7' 12,900 57.6' 10,300 77 47.8' 8,800 68.4' 6,500 79.5' 5,000 A :Boom length in feet
76 42.6' 14,600 54.1' 12,700 60.1' 10,200 76 51.3' 8,800 70.8' 6,400 82.1' 5,000 B :Load radius in feet
75 45.5' 14,600 56.9' 12,400 62.7' 10,100 75 54.9' 8,800 74.3' 6,300 84.9' 5,000
C :Loaded boom angle (o)
73 51.2' 14,600 62.4' 11,900 67.5' 10,000 73 61.6' 8,800 80.5' 6,100 90.0' 4,900 o
70 59.8' 13,700 70.0' 11,200 74.6' 9,700 70 71.3' 8,300 88.9' 5,800 97.5' 4,700 D :Minimum boom angle ( ) for indicated length (no load)
68 64.6' 13,000 74.9' 10,800 78.8' 9,600 68 77.2' 7,900 94.6' 5,600 102.0' 4,600
65 71.7' 10,700 81.2' 9,000 84.9' 8,400 65 86.1' 7,500 102.0' 5,400 109.0' 4,600
63 76.3' 9,200 85.4' 7,800 88.8' 7,400 63 91.5' 6,500 107.0' 5,300 113.0' 4,500
60 82.7' 7,400 91.5' 6,400 94.6' 6,100 60 98.5' 5,100 114.0' 4,400 120.0' 4,100
NOTE:The lifting capacity data stored in the LOAD MOMENT INDICATOR (AML-C) is based on the standard
58 86.8' 6,400 95.3' 5,600 98.1' 5,400 58 104.0' 4,400 118.0' 3,700 123.0' 3,600
55 93.1' 5,200 101.0' 4,600 104.0' 4,400 55 111.0' 3,400 124.0' 3,000 129.0' 2,900 number of parts of line listed in the chart.
53 97.2' 4,500 105.0' 4,000 107.0' 3,900 53 115.0' 2,900 129.0' 2,500 132.0' 2,400 Standard number of parts of line for each boom length should be according to the following table.
50 103.0' 3,600 110.0' 3,200 112.0' 3,200 50 122.0' 2,200 134.0' 1,900 137.0' 1,900
48 107.0' 3,100 114.0' 2,800 115.0' 2,700 48 126.0' 1,800 138.0' 1,600 140.0' 1,500 Boom length in feet 39.4' 39.4' to 68.1' 68.1' to 154.2' Single top
45 112.0' 2,400 119.0' 2,200 120.0' 2,100 45 132.0' 1,300 143.0' 1,100 144.0' 1,100
(meters) (12m) (12m to 20.8m) (20.8m to 47m) Jib
43 116.0' 2,000 122.0' 1,800
40 121.0' 1,500 126.0' 1,400 Telescoping mode I, II I II I, II I, II
38 124.0' 1,200 129.0' 1,100
Number of parts of line 16 8 4 4 1

C :Loaded boom angle (o)

R :Load radius in feet
W :Rated lifting capacity in pounds

10 7
10
7
GR-1000XL RATED LIFTING CAPACITIES (IN POUNDS) GR-1000XL RATED LIFTING CAPACITIES (IN POUNDS)
ON OUTRIGGERS FULLY EXTENDED 23' 11-3/8"(7.3m) SPREAD
360o ROTATION ON OUTRIGGERS MID EXTENDED 21' 11-3/4"(6.7m) SPREAD
154.2' (47.0m) Boom + 33.2' (10.1m) Jib 154.2' (47.0m) Boom + 58.1' (17.7m) Jib o
360 ROTATION
C 3 5o offset 25o offset 45o offset C 3 5o offset 25o offset 45o offset
R W R W R W R W R W R W
A 39.4' 53.7' 68.1' (20.8m) 82.4' (25.1m) 96.8' (29.5m) 111.1' (33.9m) 125.5' (38.3m) 139.8' (42.6m) 154.2'
80 37.8' 10,800 51.5' 10,800 58.8' 9,400 80 45.8' 6,800 71.7' 6,300 83.5' 5,100 B C (12m) C (16.4m) C C C C C C C C C C C C C (47m)
79 41.5' 10,800 55.3' 10,400 62.2' 9,200 79 50.0' 6,800 75.5' 6,200 87.1' 5,100 8' 73 200,000 78 102,700
78 45.2' 10,800 58.6' 10,200 65.7' 9,000 78 54.2' 6,800 79.1' 6,000 90.3' 5,000 10' 70 175,700 76 102,700 80 90,200 79 40,100
77 49.2' 10,800 62.1' 9,900 68.4' 8,800 77 58.5' 6,800 82.7' 5,900 93.3' 5,000
76 52.6' 10,800 65.3' 9,600 71.6' 8,700 76 62.7' 6,800 86.4' 5,800 96.2' 4,900
12' 67 153,600 74 102,700 78 90,200 77 40,100
75 56.3' 10,800 69.0' 9,300 74.5' 8,500 75 66.8' 6,800 90.0' 5,700 99.5' 4,800 15' 61 128,200 70 102,700 75 89,900 75 40,100 78 42,500 78 35,500
73 63.5' 10,500 75.2' 8,900 80.5' 8,200 73 74.6' 6,800 96.7' 5,500 105.0' 4,700 20' 52 94,800 64 98,000 71 75,000 70 40,100 74 42,500 74 35,500 77 40,100 77 33,300 79 35,500 79 32,200
70 73.4' 9,600 84.5' 8,300 88.8' 7,700 70 87.2' 6,800 107.0' 5,200 113.0' 4,600 25' 41 67,800 58 65,800 66 59,500 65 40,100 71 42,500 70 35,500 74 40,100 74 33,300 77 35,500 77 32,200 79 33,300 79 28,700
68 79.7' 9,100 90.1' 7,900 94.4' 7,400 68 94.4' 6,700 113.0' 5,100 119.0' 4,500
65 88.0' 8,200 98.3' 7,200 102.0' 6,800 65 104.0' 5,900 122.0' 4,900 126.0' 4,500
30' 25 46,900 50 45,400 61 44,000 60 40,100 67 42,500 67 35,500 71 40,100 71 33,300 74 35,500 74 30,200 77 33,300 77 26,300 79 26,700 79 24,300
63 93.9' 7,500 104.0' 6,700 106.0' 6,400 63 110.0' 5,400 128.0' 4,500 132.0' 4,200 35' 42 33,400 56 32,200 55 36,200 63 34,300 63 35,500 68 35,400 68 31,600 72 35,100 72 27,300 74 30,900 74 24,000 77 26,700 77 24,100 78 20,900
60 102.0' 6,700 111.0' 6,100 114.0' 5,800 60 119.0' 4,500 136.0' 4,100 139.0' 3,800 40' 33 25,400 50 24,400 50 30,400 58 26,400 58 31,100 65 27,500 65 29,300 69 28,300 69 24,900 72 28,400 72 22,000 75 25,300 75 22,300 77 20,900
58 107.0' 5,800 116.0' 5,400 118.0' 5,100 58 124.0' 3,900 141.0' 3,600 143.0' 3,400 45' 18 19,800 44 18,900 43 24,600 54 20,800 54 25,300 61 21,800 61 25,600 65 22,600 66 22,900 69 23,100 69 20,200 72 23,500 73 20,700 75 20,700
55 114.0' 4,700 122.0' 4,400 124.0' 4,200 55 131.0' 2,900 147.0' 2,800 149.0' 2,600
53 118.0' 4,100 126.0' 3,700 128.0' 3,600 53 137.0' 2,300 152.0' 2,200 153.0' 2,100
50' 37 14,800 36 20,300 49 16,700 49 21,000 57 17,700 57 21,300 62 18,400 63 20,400 67 18,900 67 18,700 70 19,300 71 19,300 73 19,400
50 125.0' 3,200 133.0' 3,000 133.0' 2,800 50 144.0' 1,600 158.0' 1,500 158.0' 1,400 55' 28 11,600 27 17,000 44 13,400 44 17,600 53 14,500 54 18,000 59 15,200 60 18,000 64 15,700 64 17,400 68 16,100 68 17,300 71 16,400
48 129.0' 2,700 136.0' 2,400 137.0' 2,300 48 149.0' 1,100 162.0' 1,100 162.0' 1,000 60' 13 9,200 12 14,300 38 10,800 38 14,900 49 11,900 49 15,400 56 12,600 56 15,600 64 13,100 61 15,700 65 13,400 66 14,700 69 13,700
45 136.0' 2,000 142.0' 1,800 142.0' 1,700 65' 32 8,700 32 12,800 45 9,700 45 13,200 52 10,500 53 13,400 58 11,000 59 13,600 63 11,300 63 12,500 67 11,600
43 139.0' 1,600 146.0' 1,500
40 145.0' 1,100 151.0' 1,100
70' 23 7,000 23 11,000 40 8,000 40 11,400 49 8,700 49 11,600 55 9,200 56 11,800 60 9,600 61 10,700 64 9,900
75' 5 5,600 5 9,500 35 6,500 35 9,900 45 7,200 45 10,100 52 7,700 53 10,300 57 8,100 58 9,300 62 8,400
ON OUTRIGGERS FULLY EXTENDED 23' 11-3/8"(7.3m) SPREAD 80' 29 5,200 29 8,600 41 5,900 41 8,800 49 6,400 49 9,000 55 6,800 55 8,000 60 7,100
360o ROTATION 85' 21 4,200 21 7,500 36 4,800 37 7,700 46 5,300 46 7,800 52 5,700 52 6,900 57 6,000
139.8'(42.6m) Boom(telescoping mode II) + 33.2' (10.1m) Jib 139.8'(42.6m) Boom(telescoping mode II) + 58.1' (17.7m) Jib 90' 31 3,900 32 6,700 42 4,400 42 6,900 49 4,700 49 5,900 55 5,000
C o
3 5 offset o
25 offset o
45 offset C o
3 5 offset o
25 offset o
45 offset 95' 25 3,100 25 5,900 38 3,500 38 6,000 46 3,900 46 5,000 52 4,200
R W R W R W R W R W R W
80 32.7' 11,700 45.8' 11,600 53.0' 10,000 80 40.8' 7,300 64.6' 6,500 77.3' 5,200 100' 16 2,400 16 5,200 34 2,800 34 5,200 43 3,200 43 4,300 50 3,400
79 36.4' 11,700 49.0' 11,200 55.8' 9,800 79 44.7' 7,300 67.9' 6,400 80.4' 5,100 105' 29 2,100 29 4,600 40 2,500 40 3,600 47 2,800
78 39.6' 11,700 52.1' 10,900 59.1' 9,600 78 48.7' 7,300 72.0' 6,200 83.5' 5,100 110' 24 1,600 23 4,000 36 1,900 36 3,000 44 2,200
77 43.0' 11,700 55.0' 10,600 61.6' 9,400 77 52.6' 7,300 75.2' 6,100 86.2' 5,000
115' 14 3,500 32 1,400 32 2,400 41 1,600
76 46.4' 11,700 57.7' 10,300 64.1' 9,200 76 56.5' 7,300 78.1' 6,000 89.2' 5,000
75 49.4' 11,700 60.9' 10,100 67.0' 9,100 75 60.0' 7,300 81.8' 5,900 92.4' 5,000 120' 27 2,000
73 55.8' 11,500 67.0' 9,500 72.6' 8,700 73 67.0' 7,300 88.2' 5,700 97.7' 4,900 125' 21 1,600
70 65.1' 10,400 75.1' 8,900 80.1' 8,200 70 78.3' 7,300 97.5' 5,400 105.0' 4,700 D 0 27 11 38
68 70.4' 9,700 80.6' 8,400 84.9' 7,800 68 85.2' 7,100 103.0' 5,300 110.0' 4,600
65 78.4' 8,600 88.1' 7,500 91.7' 7,100 65 94.2' 6,200 112.0' 5,100 118.0' 4,600 Telescoping conditions (%)
63 83.7' 7,900 93.0' 7,000 96.4' 6,700 63 99.8' 5,700 117.0' 4,700 123.0' 4,400 Tele. I, II I I II I II I II I II I II I II I, II
60 91.0' 7,100 100.0' 6,400 103.0' 6,100 60 109.0' 5,100 124.0' 4,300 129.0' 4,000 mode
58 96.0' 6,600 104.0' 6,000 107.0' 5,800 58 114.0' 4,700 129.0' 4,000 133.0' 3,800 2nd boom 0 50 100 0 100 0 100 0 100 0 100 0 100 50 100
55 103.0' 6,000 111.0' 5,500 113.0' 5,300 55 122.0' 4,200 137.0' 3,600 139.0' 3,500 3rd boom 0 0 0 33 16 50 33 66 50 83 66 100 83 100 100
53 108.0' 5,600 115.0' 5,200 117.0' 5,000 53 127.0' 3,900 141.0' 3,400 143.0' 3,300 4th boom 0 0 0 33 16 50 33 66 50 83 66 100 83 100 100
50 114.0' 5,100 121.0' 4,700 122.0' 4,600 50 134.0' 3,500 147.0' 3,100 148.0' 3,000
48 119.0' 4,700 125.0' 4,400 126.0' 4,200 48 139.0' 3,200 151.0' 2,900 152.0' 2,700 Top boom 0 0 0 33 16 50 33 66 50 83 66 100 83 100 100
45 124.0' 4,000 130.0' 3,800 130.0' 3,600 45 145.0' 2,700 156.0' 2,600 156.0' 2,300
43 128.0' 3,600 134.0' 3,400 43 149.0' 2,400 160.0' 2,300 LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE ON OUTRIGGERS MID EXTENDED
40 134.0' 3,100 138.0' 3,000 40 155.0' 2,000 165.0' 1,900
38 137.0' 2,800 141.0' 2,700 38 159.0' 1,700 167.0' 1,700 21' 11-3/4"(6.7m) SPREAD 360 o ROTATION
35 142.0' 2,400 145.0' 2,300 35 164.0' 1,400 171.0' 1,400 A 39.4' 53.7' 68.1' (20.8m) 82.4' (25.1m) 96.8' (29.5m) 111.1' (33.9m) 125.5' (38.3m)
33 145.0' 2,200 148.0' 2,100 33 168.0' 1,200 174.0' 1,200 C B (12m) B (16.4m) B B B B B B B B B B
30 149.0' 1,900 151.0' 1,800 30 172.0' 1,000 177.0' 1,000
25 155.0' 1,500 156.0' 1,500 0 32.2' 28,300 46.5' 18,300 60.7' 8,900 60.6' 14,100 75.0' 5,600 75.0' 9,500 89.2' 3,400 89.1' 6,700 103.0' 2,000 102.0' 4,900 117.0' 800 116.0' 3,300
20 159.0' 1,200 Tele.
I, II I I II I II I II I II I II
15 162.0' 1,000 mode

ON OUTRIGGERS FULLY EXTENDED 23' 11-3/8"(7.3m) SPREAD

360o ROTATION A :Boom length in feet
125.5'(38.3m) Boom(telescoping mode I) + 33.2' (10.1m) Jib 125.5'(38.3m)Boom(telescoping mode I) + 58.1' (17.7m) Jib
B :Load radius in feet
C o
3 5 offset o
25 offset o
45 offset C o
3 5 offset o
25 offset o
45 offset
R W R W R W R W R W R W C :Loaded boom angle (o)
80 30.5' 14,600 43.5' 14,000 50.1' 10,700 80 37.2' 8,800 58.7' 7,000 71.2' 5,200 D :Minimum boom angle (o) for indicated length (no load)
79 33.3' 14,600 46.0' 13,600 52.6' 10,600 79 41.2' 8,800 61.5' 6,800 73.9' 5,100
78 36.0' 14,600 49.2' 13,300 55.1' 10,500 78 44.8' 8,800 65.4' 6,700 76.8' 5,100
77 39.0' 14,600 51.7' 12,900 57.6' 10,300 77 47.8' 8,800 68.4' 6,500 79.5' 5,000
76 42.6' 14,600 54.1' 12,700 60.1' 10,200 76 51.3' 8,800 70.8' 6,400 82.1' 5,000
75 45.5' 14,600 56.9' 12,400 62.7' 10,100 75 54.9' 8,800 74.3' 6,300 84.9' 5,000 NOTE:The lifting capacity data stored in the LOAD MOMENT INDICATOR (AML-C) is based on the standard
73 51.2' 14,600 62.4' 11,900 67.5' 10,000 73 61.6' 8,800 80.5' 6,100 90.0' 4,900 number of parts of line listed in the chart.
70 59.8' 13,700 70.0' 11,200 74.6' 9,700 70 71.3' 8,300 88.9' 5,800 97.5' 4,700
Standard number of parts of line for each boom length should be according to the following table.
68 64.6' 13,000 74.9' 10,800 78.8' 9,600 68 77.2' 7,900 94.6' 5,600 102.0' 4,600
65 72.3' 12,100 82.0' 10,300 85.3' 9,500 65 86.1' 7,500 102.0' 5,400 109.0' 4,600
63 77.1' 11,600 86.4' 10,000 89.2' 9,300 63 92.0' 7,100 107.0' 5,300 113.0' 4,500 Boom length in feet 39.4' 39.4' to 68.1' 68.1' to 154.2' Single top
60 84.1' 10,100 93.0' 9,100 95.3' 8,500 60 99.9' 6,800 115.0' 5,100 120.0' 4,500 (meters) (12m) (12m to 20.8m) (20.8m to 47m) Jib
58 88.2' 8,900 96.6' 8,100 99.0' 7,600 58 105.0' 6,500 119.0' 5,000 124.0' 4,400
55 94.2' 7,500 102.0' 6,900 104.0' 6,500 55 112.0' 5,400 126.0' 4,800 129.0' 4,400 Telescoping mode I, II I II I, II I, II
53 98.4' 6,700 106.0' 6,200 108.0' 5,900 53 117.0' 4,800 130.0' 4,300 133.0' 4,200
50 104.0' 5,700 111.0' 5,300 112.0' 5,000 50 123.0' 4,000 136.0' 3,600 138.0' 3,500
Number of parts of line 16 8 4 4 1
48 108.0' 5,100 115.0' 4,800 116.0' 4,500 48 127.0' 3,500 139.0' 3,200 140.0' 3,100
45 113.0' 4,300 120.0' 4,100 120.0' 3,800 45 133.0' 2,900 144.0' 2,700 145.0' 2,500
43 117.0' 3,900 123.0' 3,700 43 137.0' 2,600 147.0' 2,400
40 122.0' 3,300 127.0' 3,200 40 143.0' 2,100 151.0' 2,000
38 125.0' 3,000 129.0' 2,900 38 146.0' 1,800 154.0' 1,700
35 129.0' 2,500 133.0' 2,400 35 151.0' 1,500 158.0' 1,400
33 132.0' 2,300 135.0' 2,200 33 154.0' 1,300 160.0' 1,200
30 136.0' 2,000 139.0' 1,900 30 158.0' 1,000 163.0' 1,000
25 141.0' 1,500 143.0' 1,500
20 145.0' 1,200 C :Loaded boom angle (o)
15 148.0' 1,000 R :Load radius in feet
W :Rated lifting capacity in pounds

8 9
9
8
GR-1000XL RATED LIFTING CAPACITIES (IN POUNDS) GR-1000XL RATED LIFTING CAPACITIES (IN POUNDS)
ON OUTRIGGERS FULLY EXTENDED 23' 11-3/8"(7.3m) SPREAD
360o ROTATION
154.2' (47.0m) Boom + 33.2' (10.1m) Jib 154.2' (47.0m) Boom + 58.1' (17.7m) Jib ON OUTRIGGERS MID EXTENDED 21' 11-3/4"(6.7m) SPREAD
C 3 5o offset 25o offset 45o offset C 3 5o offset 25o offset 45o offset o
R W R W R W R W R W R W
360 ROTATION
80 37.8' 10,800 51.5' 10,800 58.8' 9,400 80 45.8' 6,800 71.7' 6,300 83.5' 5,100 A 39.4' 53.7' 68.1' (20.8m) 82.4' (25.1m) 96.8' (29.5m) 111.1' (33.9m) 125.5' (38.3m) 139.8' (42.6m) 154.2'
79 41.5' 10,800 55.3' 10,400 62.2' 9,200 79 50.0' 6,800 75.5' 6,200 87.1' 5,100 B C (12m) C (16.4m) C C C C C C C C C C C C C (47m)
78 45.2' 10,800 58.6' 10,200 65.7' 9,000 78 54.2' 6,800 79.1' 6,000 90.3' 5,000 8' 73 200,000 78 102,700
77 49.2' 10,800 62.1' 9,900 68.4' 8,800 77 58.5' 6,800 82.7' 5,900 93.3' 5,000
10' 70 175,700 76 102,700 80 90,200 79 40,100
76 52.6' 10,800 65.3' 9,600 71.6' 8,700 76 62.7' 6,800 86.4' 5,800 96.2' 4,900
75 56.3' 10,800 69.0' 9,300 74.5' 8,500 75 66.8' 6,800 90.0' 5,700 99.5' 4,800 12' 67 153,600 74 102,700 78 90,200 77 40,100
73 63.5' 10,500 75.2' 8,900 80.5' 8,200 73 74.6' 6,800 96.7' 5,500 105.0' 4,700 15' 61 128,200 70 102,700 75 89,900 75 40,100 78 42,500 78 35,500
70 73.4' 9,600 84.5' 8,300 88.8' 7,700 70 87.2' 6,800 107.0' 5,200 113.0' 4,600 20' 52 94,800 64 98,000 71 75,000 70 40,100 74 42,500 74 35,500 77 40,100 77 33,300 79 35,500 79 32,200
68 79.7' 9,100 90.1' 7,900 94.4' 7,400 68 94.4' 6,700 113.0' 5,100 119.0' 4,500
25' 41 67,800 58 65,800 66 59,500 65 40,100 71 42,500 70 35,500 74 40,100 74 33,300 77 35,500 77 32,200 79 33,300 79 28,700
65 88.0' 8,200 98.3' 7,200 102.0' 6,800 65 104.0' 5,900 122.0' 4,900 126.0' 4,500
63 93.9' 7,500 104.0' 6,700 106.0' 6,400 63 110.0' 5,400 128.0' 4,500 132.0' 4,200 30' 25 46,900 50 45,400 61 44,000 60 40,100 67 42,500 67 35,500 71 40,100 71 33,300 74 35,500 74 30,200 77 33,300 77 26,300 79 26,700 79 24,300
60 102.0' 6,700 111.0' 6,100 114.0' 5,800 60 119.0' 4,500 136.0' 4,100 139.0' 3,800 35' 42 33,400 56 32,200 55 36,200 63 34,300 63 35,500 68 35,400 68 31,600 72 35,100 72 27,300 74 30,900 74 24,000 77 26,700 77 24,100 78 20,900
58 107.0' 5,800 116.0' 5,400 118.0' 5,100 58 124.0' 3,900 141.0' 3,600 143.0' 3,400 40' 33 25,400 50 24,400 50 30,400 58 26,400 58 31,100 65 27,500 65 29,300 69 28,300 69 24,900 72 28,400 72 22,000 75 25,300 75 22,300 77 20,900
55 114.0' 4,700 122.0' 4,400 124.0' 4,200 55 131.0' 2,900 147.0' 2,800 149.0' 2,600
45' 18 19,800 44 18,900 43 24,600 54 20,800 54 25,300 61 21,800 61 25,600 65 22,600 66 22,900 69 23,100 69 20,200 72 23,500 73 20,700 75 20,700
53 118.0' 4,100 126.0' 3,700 128.0' 3,600 53 137.0' 2,300 152.0' 2,200 153.0' 2,100
50 125.0' 3,200 133.0' 3,000 133.0' 2,800 50 144.0' 1,600 158.0' 1,500 158.0' 1,400 50' 37 14,800 36 20,300 49 16,700 49 21,000 57 17,700 57 21,300 62 18,400 63 20,400 67 18,900 67 18,700 70 19,300 71 19,300 73 19,400
48 129.0' 2,700 136.0' 2,400 137.0' 2,300 48 149.0' 1,100 162.0' 1,100 162.0' 1,000 55' 28 11,600 27 17,000 44 13,400 44 17,600 53 14,500 54 18,000 59 15,200 60 18,000 64 15,700 64 17,400 68 16,100 68 17,300 71 16,400
45 136.0' 2,000 142.0' 1,800 142.0' 1,700 60' 13 9,200 12 14,300 38 10,800 38 14,900 49 11,900 49 15,400 56 12,600 56 15,600 64 13,100 61 15,700 65 13,400 66 14,700 69 13,700
43 139.0' 1,600 146.0' 1,500
65' 32 8,700 32 12,800 45 9,700 45 13,200 52 10,500 53 13,400 58 11,000 59 13,600 63 11,300 63 12,500 67 11,600
40 145.0' 1,100 151.0' 1,100
70' 23 7,000 23 11,000 40 8,000 40 11,400 49 8,700 49 11,600 55 9,200 56 11,800 60 9,600 61 10,700 64 9,900
ON OUTRIGGERS FULLY EXTENDED 23' 11-3/8"(7.3m) SPREAD 75' 5 5,600 5 9,500 35 6,500 35 9,900 45 7,200 45 10,100 52 7,700 53 10,300 57 8,100 58 9,300 62 8,400
360o ROTATION 80' 29 5,200 29 8,600 41 5,900 41 8,800 49 6,400 49 9,000 55 6,800 55 8,000 60 7,100
139.8'(42.6m) Boom(telescoping mode II) + 33.2' (10.1m) Jib 139.8'(42.6m) Boom(telescoping mode II) + 58.1' (17.7m) Jib 85' 21 4,200 21 7,500 36 4,800 37 7,700 46 5,300 46 7,800 52 5,700 52 6,900 57 6,000
C o
3 5 offset o
25 offset o
45 offset C o
3 5 offset o
25 offset o
45 offset 90' 31 3,900 32 6,700 42 4,400 42 6,900 49 4,700 49 5,900 55 5,000
R W R W R W R W R W R W
80 32.7' 11,700 45.8' 11,600 53.0' 10,000 80 40.8' 7,300 64.6' 6,500 77.3' 5,200 95' 25 3,100 25 5,900 38 3,500 38 6,000 46 3,900 46 5,000 52 4,200
79 36.4' 11,700 49.0' 11,200 55.8' 9,800 79 44.7' 7,300 67.9' 6,400 80.4' 5,100 100' 16 2,400 16 5,200 34 2,800 34 5,200 43 3,200 43 4,300 50 3,400
78 39.6' 11,700 52.1' 10,900 59.1' 9,600 78 48.7' 7,300 72.0' 6,200 83.5' 5,100 105' 29 2,100 29 4,600 40 2,500 40 3,600 47 2,800
77 43.0' 11,700 55.0' 10,600 61.6' 9,400 77 52.6' 7,300 75.2' 6,100 86.2' 5,000 110' 24 1,600 23 4,000 36 1,900 36 3,000 44 2,200
76 46.4' 11,700 57.7' 10,300 64.1' 9,200 76 56.5' 7,300 78.1' 6,000 89.2' 5,000
75 49.4' 11,700 60.9' 10,100 67.0' 9,100 75 60.0' 7,300 81.8' 5,900 92.4' 5,000 115' 14 3,500 32 1,400 32 2,400 41 1,600
73 55.8' 11,500 67.0' 9,500 72.6' 8,700 73 67.0' 7,300 88.2' 5,700 97.7' 4,900 120' 27 2,000
70 65.1' 10,400 75.1' 8,900 80.1' 8,200 70 78.3' 7,300 97.5' 5,400 105.0' 4,700 125' 21 1,600
68 70.4' 9,700 80.6' 8,400 84.9' 7,800 68 85.2' 7,100 103.0' 5,300 110.0' 4,600 D 0 27 11 38
65 78.4' 8,600 88.1' 7,500 91.7' 7,100 65 94.2' 6,200 112.0' 5,100 118.0' 4,600
63 83.7' 7,900 93.0' 7,000 96.4' 6,700 63 99.8' 5,700 117.0' 4,700 123.0' 4,400 Telescoping conditions (%)
60 91.0' 7,100 100.0' 6,400 103.0' 6,100 60 109.0' 5,100 124.0' 4,300 129.0' 4,000 Tele. I, II I I II I II I II I II I II I II I, II
58 96.0' 6,600 104.0' 6,000 107.0' 5,800 58 114.0' 4,700 129.0' 4,000 133.0' 3,800 mode
55 103.0' 6,000 111.0' 5,500 113.0' 5,300 55 122.0' 4,200 137.0' 3,600 139.0' 3,500 2nd boom 0 50 100 0 100 0 100 0 100 0 100 0 100 50 100
53 108.0' 5,600 115.0' 5,200 117.0' 5,000 53 127.0' 3,900 141.0' 3,400 143.0' 3,300 3rd boom 0 0 0 33 16 50 33 66 50 83 66 100 83 100 100
50 114.0' 5,100 121.0' 4,700 122.0' 4,600 50 134.0' 3,500 147.0' 3,100 148.0' 3,000
4th boom 0 0 0 33 16 50 33 66 50 83 66 100 83 100 100
48 119.0' 4,700 125.0' 4,400 126.0' 4,200 48 139.0' 3,200 151.0' 2,900 152.0' 2,700
45 124.0' 4,000 130.0' 3,800 130.0' 3,600 45 145.0' 2,700 156.0' 2,600 156.0' 2,300 Top boom 0 0 0 33 16 50 33 66 50 83 66 100 83 100 100
43 128.0' 3,600 134.0' 3,400 43 149.0' 2,400 160.0' 2,300
40 134.0' 3,100 138.0' 3,000 40 155.0' 2,000 165.0' 1,900
38 137.0' 2,800 141.0' 2,700 38 159.0' 1,700 167.0' 1,700
LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE ON OUTRIGGERS MID EXTENDED
o
35 142.0' 2,400 145.0' 2,300 35 164.0' 1,400 171.0' 1,400 21' 11-3/4"(6.7m) SPREAD 360 ROTATION
33 145.0' 2,200 148.0' 2,100 33 168.0' 1,200 174.0' 1,200 A 39.4' 53.7' 68.1' (20.8m) 82.4' (25.1m) 96.8' (29.5m) 111.1' (33.9m) 125.5' (38.3m)
30 149.0' 1,900 151.0' 1,800 30 172.0' 1,000 177.0' 1,000
C B (12m) B (16.4m) B B B B B B B B B B
25 155.0' 1,500 156.0' 1,500
20 159.0' 1,200 0 32.2' 28,300 46.5' 18,300 60.7' 8,900 60.6' 14,100 75.0' 5,600 75.0' 9,500 89.2' 3,400 89.1' 6,700 103.0' 2,000 102.0' 4,900 117.0' 800 116.0' 3,300
15 162.0' 1,000 Tele.
I, II I I II I II I II I II I II
mode
ON OUTRIGGERS FULLY EXTENDED 23' 11-3/8"(7.3m) SPREAD
360o ROTATION
125.5'(38.3m) Boom(telescoping mode I) + 33.2' (10.1m) Jib 125.5'(38.3m)Boom(telescoping mode I) + 58.1' (17.7m) Jib A :Boom length in feet
C o
3 5 offset o
25 offset o
45 offset C 3 5o offset 25o offset 45o offset
R W R W R W R W R W R W B :Load radius in feet
80 30.5' 14,600 43.5' 14,000 50.1' 10,700 80 37.2' 8,800 58.7' 7,000 71.2' 5,200 C :Loaded boom angle (o)
79 33.3' 14,600 46.0' 13,600 52.6' 10,600 79 41.2' 8,800 61.5' 6,800 73.9' 5,100 D :Minimum boom angle (o) for indicated length (no load)
78 36.0' 14,600 49.2' 13,300 55.1' 10,500 78 44.8' 8,800 65.4' 6,700 76.8' 5,100
77 39.0' 14,600 51.7' 12,900 57.6' 10,300 77 47.8' 8,800 68.4' 6,500 79.5' 5,000
76 42.6' 14,600 54.1' 12,700 60.1' 10,200 76 51.3' 8,800 70.8' 6,400 82.1' 5,000
75 45.5' 14,600 56.9' 12,400 62.7' 10,100 75 54.9' 8,800 74.3' 6,300 84.9' 5,000
73 51.2' 14,600 62.4' 11,900 67.5' 10,000 73 61.6' 8,800 80.5' 6,100 90.0' 4,900 NOTE:The lifting capacity data stored in the LOAD MOMENT INDICATOR (AML-C) is based on the standard
70 59.8' 13,700 70.0' 11,200 74.6' 9,700 70 71.3' 8,300 88.9' 5,800 97.5' 4,700 number of parts of line listed in the chart.
68 64.6' 13,000 74.9' 10,800 78.8' 9,600 68 77.2' 7,900 94.6' 5,600 102.0' 4,600
65 72.3' 12,100 82.0' 10,300 85.3' 9,500 65 86.1' 7,500 102.0' 5,400 109.0' 4,600
Standard number of parts of line for each boom length should be according to the following table.
63 77.1' 11,600 86.4' 10,000 89.2' 9,300 63 92.0' 7,100 107.0' 5,300 113.0' 4,500
60 84.1' 10,100 93.0' 9,100 95.3' 8,500 60 99.9' 6,800 115.0' 5,100 120.0' 4,500 Boom length in feet 39.4' 39.4' to 68.1' 68.1' to 154.2' Single top
58 88.2' 8,900 96.6' 8,100 99.0' 7,600 58 105.0' 6,500 119.0' 5,000 124.0' 4,400 (meters) (12m) (12m to 20.8m) (20.8m to 47m) Jib
55 94.2' 7,500 102.0' 6,900 104.0' 6,500 55 112.0' 5,400 126.0' 4,800 129.0' 4,400
53 98.4' 6,700 106.0' 6,200 108.0' 5,900 53 117.0' 4,800 130.0' 4,300 133.0' 4,200 Telescoping mode I, II I II I, II I, II
50 104.0' 5,700 111.0' 5,300 112.0' 5,000 50 123.0' 4,000 136.0' 3,600 138.0' 3,500
48 108.0' 5,100 115.0' 4,800 116.0' 4,500 48 127.0' 3,500 139.0' 3,200 140.0' 3,100 Number of parts of line 16 8 4 4 1
45 113.0' 4,300 120.0' 4,100 120.0' 3,800 45 133.0' 2,900 144.0' 2,700 145.0' 2,500
43 117.0' 3,900 123.0' 3,700 43 137.0' 2,600 147.0' 2,400
40 122.0' 3,300 127.0' 3,200 40 143.0' 2,100 151.0' 2,000
38 125.0' 3,000 129.0' 2,900 38 146.0' 1,800 154.0' 1,700
35 129.0' 2,500 133.0' 2,400 35 151.0' 1,500 158.0' 1,400
33 132.0' 2,300 135.0' 2,200 33 154.0' 1,300 160.0' 1,200
30 136.0' 2,000 139.0' 1,900 30 158.0' 1,000 163.0' 1,000
25 141.0' 1,500 143.0' 1,500
20 145.0' 1,200 C :Loaded boom angle (o)
15 148.0' 1,000 R :Load radius in feet
W :Rated lifting capacity in pounds

8 9
8
9
GR-1000XL RATED LIFTING CAPACITIES (IN POUNDS) GR-1000XL RATED LIFTING CAPACITIES (IN POUNDS)
ON OUTRIGGERS FULLY EXTENDED 23' 11-3/8"(7.3m) SPREAD
ON OUTRIGGERS MID EXTENDED 21' 11-3/4"(6.7m) SPREAD o
360 ROTATION o 360 ROTATION
154.2' (47.0m) Boom + 33.2' (10.1m) Jib 154.2' (47.0m) Boom + 58.1' (17.7m) Jib A 39.4' 53.7' 68.1' (20.8m) 82.4' (25.1m) 96.8' (29.5m) 111.1' (33.9m) 125.5' (38.3m) 139.8' (42.6m) 154.2'
C o
3.5 offset o
25 offset o
45 offset C 3.5o offset 25o offset 45o offset B C (12m) C (16.4m) C C C C C C C C C C C C C (47m)
R W R W R W R W R W R W 8' 73 200,000 78 102,700
80 37.8' 10,800 51.5' 10,800 58.8' 9,400 80 45.8' 6,800 71.7' 6,300 83.5' 5,100 10' 70 180,000 76 102,700 80 90,200 79 40,100
79 41.5' 10,800 55.3' 10,400 62.2' 9,200 79 50.0' 6,800 75.5' 6,200 87.1' 5,100
78 45.2' 10,800 58.6' 10,200 65.7' 9,000 78 54.2' 6,800 79.1' 6,000 90.3' 5,000 12' 67 157,900 74 102,700 78 90,200 77 40,100
77 49.2' 10,800 62.1' 9,900 68.4' 8,800 77 58.5' 6,800 82.7' 5,900 93.3' 5,000 15' 61 132,300 70 102,700 75 89,900 75 40,100 78 42,500 78 35,500
76 52.6' 10,800 65.3' 9,600 71.6' 8,700 76 62.7' 6,800 86.4' 5,800 96.2' 4,900 20' 52 99,700 64 99,100 71 76,100 70 40,100 74 42,500 74 35,500 77 40,100 77 33,300 79 35,500 79 32,200
75 56.3' 10,800 69.0' 9,300 74.5' 8,500 75 66.8' 6,800 90.0' 5,700 99.5' 4,800 25' 41 76,900 58 76,200 66 65,600 65 40,100 71 42,500 70 35,500 74 40,100 74 33,300 77 35,500 77 32,200 79 33,300 79 28,700
73 63.5' 10,500 75.2' 8,900 80.5' 8,200 73 74.6' 6,800 96.7' 5,500 105.0' 4,700
30' 25 50,700 51 57,700 61 56,700 60 40,100 67 42,500 67 35,500 71 40,100 71 33,300 74 35,500 74 30,200 77 33,300 77 26,300 79 26,700 79 24,300
70 73.4' 9,600 84.5' 8,300 88.8' 7,700 70 87.2' 6,800 107.0' 5,200 113.0' 4,600
68 79.0' 8,700 89.8' 7,700 94.0' 7,000 68 93.8' 6,300 113.0' 5,100 119.0' 4,500 35' 43 42,800 56 41,800 55 40,100 63 42,500 63 35,500 68 39,500 68 31,600 72 35,100 72 27,300 74 30,900 74 24,000 77 26,700 77 24,100 78 20,900
65 86.7' 6,700 96.9' 6,000 101.0' 5,600 65 102.0' 4,700 120.0' 4,000 125.0' 3,700 40' 33 33,100 50 32,100 49 36,400 59 34,100 59 35,500 65 34,000 65 29,300 69 32,000 69 24,900 72 28,400 72 22,000 75 25,300 75 22,300 77 20,900
63 91.8' 5,600 102.0' 5,100 105.0' 4,700 63 108.0' 3,800 125.0' 3,300 130.0' 3,100 45' 18 26,200 44 25,400 43 31,100 54 27,300 54 31,800 61 28,300 61 26,500 66 28,000 66 22,900 69 26,100 69 20,200 72 23,500 73 20,700 75 20,700
60 99.3' 4,300 109.0' 3,900 112.0' 3,700 60 116.0' 2,800 133.0' 2,400 137.0' 2,300 50' 37 20,400 36 25,900 49 22,200 49 26,600 57 23,200 58 24,100 63 24,000 63 21,300 67 22,900 67 18,700 70 21,800 71 19,300 73 19,400
58 104.0' 3,500 114.0' 3,300 116.0' 3,100 58 121.0' 2,200 138.0' 1,900 141.0' 1,800
55' 28 16,600 27 20,900 44 18,400 44 22,600 54 19,300 54 22,200 59 20,100 60 19,600 64 20,100 64 17,400 68 19,600 68 18,000 71 18,100
55 112.0' 2,600 121.0' 2,400 122.0' 2,300 55 129.0' 1,400 145.0' 1,300 147.0' 1,200
53 116.0' 2,100 125.0' 1,900 126.0' 1,800 53 134.0' 1,000 60' 13 13,600 12 15,900 39 15,300 38 19,400 49 16,200 50 19,700 56 17,000 57 18,200 61 17,300 62 16,100 66 17,400 66 16,800 69 16,800
50 123.0' 1,400 131.0' 1,300 132.0' 1,200 65' 32 12,700 32 16,800 45 13,700 45 17,100 53 14,400 53 16,600 58 14,800 59 15,000 63 15,300 64 15,800 67 15,200
48 128.0' 1,000 70' 24 10,600 23 14,600 40 11,600 41 15,000 49 12,300 50 15,200 56 12,700 56 13,800 61 13,200 61 14,300 65 13,400
75' 7 8,900 5 11,700 35 9,800 35 13,200 45 10,600 46 13,400 53 10,900 53 12,700 58 11,400 59 12,500 62 11,700
80' 29 8,300 29 11,600 41 9,100 42 11,900 49 9,500 50 11,700 55 9,900 56 11,000 60 10,200
ON OUTRIGGERS MID EXTENDED 21' 11-3/4"(6.7m) SPREAD
85' 21 7,100 21 10,300 37 7,800 38 10,500 46 8,200 46 10,800 53 8,600 53 9,700 58 8,900
360o ROTATION
139.8'(42.6m) Boom(telescoping mode II) + 33.2' (10.1m) Jib 139.8'(42.6m) Boom(telescoping mode II) + 58.1' (17.7m) Jib
90' 31 6,600 33 9,400 42 7,000 43 9,600 50 7,500 50 8,600 55 7,700
C 3.5o offset 25o offset 45o offset C 3.5o offset 25o offset 45o offset 95' 25 5,600 27 8,400 38 6,000 39 8,600 47 6,500 47 7,600 53 6,700
R W R W R W R W R W R W 100' 17 4,800 19 7,500 34 5,200 35 7,700 43 5,600 44 6,700 50 5,900
80 32.7' 11,700 45.8' 11,600 53.0' 10,000 80 40.8' 7,300 64.6' 6,500 77.3' 5,200 105' 29 4,400 30 6,900 40 4,800 41 5,900 47 5,100
79 36.4' 11,700 49.0' 11,200 55.8' 9,800 79 44.7' 7,300 67.9' 6,400 80.4' 5,100
110' 24 3,700 24 6,200 37 4,100 37 5,200 44 4,300
78 39.6' 11,700 52.1' 10,900 59.1' 9,600 78 48.7' 7,300 72.0' 6,200 83.5' 5,100
77 43.0' 11,700 55.0' 10,600 61.6' 9,400 77 52.6' 7,300 75.2' 6,100 86.2' 5,000 115' 15 3,100 15 5,600 33 3,500 32 4,500 41 3,700
76 46.4' 11,700 57.7' 10,300 64.1' 9,200 76 56.5' 7,300 78.1' 6,000 89.2' 5,000 120' 27 2,900 28 4,000 38 3,200
75 49.4' 11,700 60.9' 10,100 67.0' 9,100 75 60.0' 7,300 81.8' 5,900 92.4' 5,000 125' 22 2,400 23 3,500 34 2,600
73 55.8' 11,500 67.0' 9,500 72.6' 8,700 73 67.0' 7,300 88.2' 5,700 97.7' 4,900 130' 14 2,000 14 3,100 30 2,200
70 65.1' 10,400 75.1' 8,900 80.1' 8,200 70 78.3' 7,300 97.5' 5,400 105.0' 4,700
135' 26 1,800
68 70.4' 9,700 80.6' 8,400 84.9' 7,800 68 85.2' 7,100 103.0' 5,300 110.0' 4,600
65 78.4' 8,600 88.1' 7,500 91.7' 7,100 65 94.2' 6,200 112.0' 5,100 118.0' 4,600 D 0 20
63 83.7' 7,900 93.0' 7,000 96.4' 6,700 63 99.8' 5,700 117.0' 4,700 123.0' 4,400 Telescoping conditions (%)
60 91.1' 6,600 99.4' 6,000 102.0' 5,600 60 108.0' 4,700 124.0' 4,000 129.0' 3,800 Tele.
58 95.6' 5,800 104.0' 5,200 106.0' 5,000 58 113.0' 4,000 128.0' 3,400 133.0' 3,300 I, II I I II I II I II I II I II I II I, II
mode
55 102.0' 4,700 110.0' 4,300 112.0' 4,100 55 120.0' 3,100 135.0' 2,700 139.0' 2,600 2nd boom 0 50 100 0 100 0 100 0 100 0 100 0 100 50 100
53 107.0' 4,100 114.0' 3,700 116.0' 3,600 53 125.0' 2,600 139.0' 2,300 142.0' 2,200 3rd boom 0 0 0 33 16 50 33 66 50 83 66 100 83 100 100
50 113.0' 3,300 120.0' 3,000 121.0' 2,900 50 132.0' 2,000 145.0' 1,800 147.0' 1,700
48 117.0' 2,800 124.0' 2,600 125.0' 2,600 48 137.0' 1,600 149.0' 1,500 151.0' 1,400 4th boom 0 0 0 33 16 50 33 66 50 83 66 100 83 100 100
45 123.0' 2,200 129.0' 2,100 129.0' 2,100 45 143.0' 1,200 155.0' 1,000 155.0' 1,000 Top boom 0 0 0 33 16 50 33 66 50 83 66 100 83 100 100
43 127.0' 1,900 132.0' 1,800
40 132.0' 1,500 137.0' 1,400
LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE ON OUTRIGGERS FULLY EXTENDED
38 136.0' 1,200 140.0' 1,100
23' 11-3/8"(7.3m) SPREAD 360 o ROTATION
A 39.4' 53.7' 68.1' (20.8m) 82.4' (25.1m) 96.8' (29.5m) 111.1' (33.9m) 125.5' (38.3m) 139.8' (42.6m)
ON OUTRIGGERS MID EXTENDED 21' 11-3/4"(6.7m) SPREAD C B (12m) B (16.4m) B B B B B B B B B B B B
360o ROTATION 0o 32.2' 30,900 46.6' 19,400 60.7' 12,100 60.5' 15,600 75.0' 8,900 75.0' 11,800 89.0' 6,200 89.0' 8,200 102.0' 4,400 103.0' 6,200 117.0' 3,000 116.0' 5,400 131.0' 2,000 130.0' 3,100
125.5'(38.3m) Boom(telescoping mode I) + 33.2' (10.1m) Jib 125.5'(38.3m)Boom(telescoping mode I) + 58.1' (17.7m) Jib Tele.
C o
3.5 offset o
25 offset o
45 offset C o
3.5 offset o
25 offset o
45 offset I, II I I II I II I II I II I II I II
mode
R W R W R W R W R W R W
80 30.5' 14,600 43.5' 14,000 50.1' 10,700 80 37.2' 8,800 58.7' 7,000 71.2' 5,200
79 33.3' 14,600 46.0' 13,600 52.6' 10,600 79 41.2' 8,800 61.5' 6,800 73.9' 5,100
78 36.0' 14,600 49.2' 13,300 55.1' 10,500 78 44.8' 8,800 65.4' 6,700 76.8' 5,100 A :Boom length in feet
77 39.0' 14,600 51.7' 12,900 57.6' 10,300 77 47.8' 8,800 68.4' 6,500 79.5' 5,000 B :Load radius in feet
76 42.6' 14,600 54.1' 12,700 60.1' 10,200 76 51.3' 8,800 70.8' 6,400 82.1' 5,000 C :Loaded boom angle (o)
75 45.5' 14,600 56.9' 12,400 62.7' 10,100 75 54.9' 8,800 74.3' 6,300 84.9' 5,000 o
73 51.2' 14,600 62.4' 11,900 67.5' 10,000 73 61.6' 8,800 80.5' 6,100 90.0' 4,900
D :Minimum boom angle ( ) for indicated length (no load)
70 59.8' 13,700 70.0' 11,200 74.6' 9,700 70 71.3' 8,300 88.9' 5,800 97.5' 4,700
68 64.6' 13,000 74.9' 10,800 78.8' 9,600 68 77.2' 7,900 94.6' 5,600 102.0' 4,600
65 71.7' 10,700 81.2' 9,000 84.9' 8,400 65 86.1' 7,500 102.0' 5,400 109.0' 4,600
63 76.3' 9,200 85.4' 7,800 88.8' 7,400 63 91.5' 6,500 107.0' 5,300 113.0' 4,500 NOTE:The lifting capacity data stored in the LOAD MOMENT INDICATOR (AML-C) is based on the standard
60 82.7' 7,400 91.5' 6,400 94.6' 6,100 60 98.5' 5,100 114.0' 4,400 120.0' 4,100
58 86.8' 6,400 95.3' 5,600 98.1' 5,400 58 104.0' 4,400 118.0' 3,700 123.0' 3,600 number of parts of line listed in the chart.
55 93.1' 5,200 101.0' 4,600 104.0' 4,400 55 111.0' 3,400 124.0' 3,000 129.0' 2,900 Standard number of parts of line for each boom length should be according to the following table.
53 97.2' 4,500 105.0' 4,000 107.0' 3,900 53 115.0' 2,900 129.0' 2,500 132.0' 2,400
50 103.0' 3,600 110.0' 3,200 112.0' 3,200 50 122.0' 2,200 134.0' 1,900 137.0' 1,900 Boom length in feet 39.4' 39.4' to 68.1' 68.1' to 154.2' Single top
48 107.0' 3,100 114.0' 2,800 115.0' 2,700 48 126.0' 1,800 138.0' 1,600 140.0' 1,500 (meters) (12m) (12m to 20.8m) (20.8m to 47m) Jib
45 112.0' 2,400 119.0' 2,200 120.0' 2,100 45 132.0' 1,300 143.0' 1,100 144.0' 1,100
43 116.0' 2,000 122.0' 1,800 Telescoping mode I, II I II I, II I, II
40 121.0' 1,500 126.0' 1,400
38 124.0' 1,200 129.0' 1,100 Number of parts of line 16 8 4 4 1

C :Loaded boom angle (o)

R :Load radius in feet
W :Rated lifting capacity in pounds

10 7
7
10
GR-1000XL WORKING RANGE CHART

GR-1000XL RATED LIFTING CAPACITIES (IN POUNDS)

ON OUTRIGGERS MID EXTENDED 18' 1/2"(5.5m) SPREAD
o
360 ROTATION
A 39.4' 53.7' 68.1' (20.8m) 82.4' (25.1m) 96.8' (29.5m) 111.1' (33.9m) 125.5' (38.3m) 139.8' (42.6m) 154.2'
B C (12m) C (16.4m) C C C C C C C C C C C C C (47m)
8' 73 191,600 78 102,700
10' 70 164,000 76 102,700 80 90,200 79 40,100
12' 67 142,400 74 102,700 78 90,200 77 40,100
15' 61 113,500 70 102,700 75 89,900 75 40,100 78 42,500 78 35,500
20' 52 75,400 64 73,400 71 67,200 70 40,100 74 42,500 74 35,500 77 40,100 77 33,300 79 35,500 79 32,200
25' 41 48,200 57 46,700 66 45,400 65 40,100 71 42,500 70 35,500 74 40,100 74 33,300 77 35,500 77 32,200 79 33,300 79 28,700
30' 25 33,900 50 32,700 61 31,500 60 35,500 67 33,600 67 35,500 71 34,800 71 33,300 74 35,500 74 30,200 77 33,300 77 26,300 79 26,700 79 24,300
35' 42 23,900 55 23,000 55 28,900 63 24,900 62 29,500 68 26,000 68 29,900 71 26,800 72 27,300 74 27,300 74 24,000 77 26,700 77 24,100 78 20,900
40' 33 18,000 50 17,100 50 22,800 58 19,000 58 23,400 64 20,100 64 23,800 68 20,800 69 24,100 71 21,400 72 22,000 74 21,800 75 22,300 77 20,900
45' 18 13,700 44 12,900 43 18,300 54 14,800 54 19,000 61 15,800 61 19,400 65 16,500 65 19,600 69 17,000 69 19,800 72 17,400 72 18,700 75 17,700
50' 36 9,700 36 14,900 49 11,500 49 15,600 57 12,600 57 16,000 62 13,200 62 16,300 66 13,800 67 16,400 70 14,100 70 15,300 73 14,400
55' 27 7,200 27 12,300 44 8,900 44 13,000 53 10,000 53 13,400 59 10,700 59 13,700 63 11,200 64 13,800 67 11,600 68 12,700 70 11,900
60' 12 5,300 12 10,300 38 6,900 38 10,800 49 7,900 49 11,300 55 8,600 56 11,600 61 9,100 61 11,700 65 9,500 65 10,700 68 9,800
65' 32 5,200 32 9,100 45 6,200 45 9,500 52 6,900 52 9,800 58 7,500 58 10,000 62 7,800 63 9,000 66 8,100
70' 23 3,800 23 7,700 40 4,800 40 8,100 48 5,500 49 8,300 55 6,000 55 8,500 60 6,400 60 7,500 64 6,700
75' 6 2,600 5 6,500 35 3,600 35 6,800 45 4,300 45 7,100 52 4,800 52 7,300 57 5,200 57 6,300 61 5,500
80' 29 2,600 28 5,800 41 3,200 41 6,000 49 3,700 49 6,200 55 4,100 55 5,200 59 4,400
85' 21 1,700 20 4,900 36 2,300 36 5,100 45 2,800 46 5,300 52 3,200 52 4,300 57 3,500
90' 31 1,600 31 4,300 42 2,100 42 4,500 49 2,400 49 3,500 54 2,700
95' 25 3,700 38 1,400 38 3,800 46 1,700 46 2,800 52 2,000
100' 16 3,100 34 3,200 43 1,100 43 2,200 49 1,400
105' 29 2,600 40 1,700
110' 23 2,200 36 1,100
115' 14 1,700
D 0 18 0 29 0 40 27 47
Telescoping conditions (%)
Tele.
I, II I I II I II I II I II I II I II I, II
mode
2nd boom 0 50 100 0 100 0 100 0 100 0 100 0 100 50 100
3rd boom 0 0 0 33 16 50 33 66 50 83 66 100 83 100 100
4th boom 0 0 0 33 16 50 33 66 50 83 66 100 83 100 100
Top boom 0 0 0 33 16 50 33 66 50 83 66 100 83 100 100

LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE ON OUTRIGGERS MID EXTENDED

18' 1/2"(5.5m) SPREAD 360 o ROTATION
A 39.4' 53.7' 68.1' (20.8m) 82.4' (25.1m) 96.8' (29.5m) 111.1' 125.5'
C B (12m) B (16.4m) B B B B B B B (33.9m) B (38.3m)
0 32.2' 29,200 46.4' 12,600 60.7' 5,000 60.7' 10,000 75.0' 2,600 75.0' 6,500 89.2' 1,100 89.1' 4,300 103.0' 2,800 116.0' 1,500
Tele.
I, II I I II I II I II II II
mode

A :Boom length in feet

B :Load radius in feet
C :Loaded boom angle (o)
D :Minimum boom angle (o) for indicated length (no load)

NOTE:The lifting capacity data stored in the LOAD MOMENT INDICATOR (AML-C) is based on the standard
number of parts of line listed in the chart.
Standard number of parts of line for each boom length should be according to the following table.

Boom length in feet 39.4' 39.4' to68.1' 68.1' to 154.2' Single top
(meters) (12m) (12m to20.8m) (20.8m to 47m) Jib
Telescoping mode I, II I II I, II I, II

Number of parts of line 16 8 4 4 1

11
6
11
 GR-1000XL WORKING RANGE CHART

GR-1000XL RATED LIFTING CAPACITIES (IN POUNDS)

ON OUTRIGGERS MID EXTENDED 18' 1/2"(5.5m) SPREAD
360o ROTATION
154.2' (47.0m) Boom + 33.2' (10.1m) Jib 154.2' (47.0m) Boom + 58.1' (17.7m) Jib
C 3 5o offset 25o offset 45o offset C 3 5o offset 25o offset 45o offset
R W R W R W R W R W R W
80 37.8' 10,800 51.5' 10,800 58.8' 9,400 80 45.8' 6,800 71.7' 6,300 83.5' 5,100
79 41.5' 10,800 55.3' 10,400 62.2' 9,200 79 50.0' 6,800 75.5' 6,200 87.1' 5,100
78 45.2' 10,800 58.6' 10,200 65.7' 9,000 78 54.2' 6,800 79.1' 6,000 90.3' 5,000
77 49.2' 10,800 62.1' 9,900 68.4' 8,800 77 58.5' 6,800 82.7' 5,900 93.3' 5,000
76 52.6' 10,800 65.3' 9,600 71.6' 8,700 76 62.7' 6,800 86.4' 5,800 96.2' 4,900
75 56.3' 10,800 69.0' 9,300 74.5' 8,500 75 66.8' 6,800 90.0' 5,700 99.5' 4,800
73 63.2' 10,100 74.4' 8,300 80.1' 7,600 73 74.6' 6,800 96.7' 5,500 105.0' 4,700
70 71.2' 7,400 82.4' 6,200 87.4' 5,700 70 84.5' 5,200 105.0' 4,200 112.0' 3,800
68 76.6' 6,000 87.3' 5,000 92.0' 4,700 68 90.3' 4,100 109.0' 3,300 117.0' 3,000
65 84.6' 4,300 95.2' 3,700 98.9' 3,500 65 98.8' 2,700 117.0' 2,300 123.0' 2,100
63 90.0' 3,400 100.0' 2,900 103.0' 2,800 63 105.0' 2,000 122.0' 1,700 128.0' 1,600
60 97.6' 2,300 107.0' 2,000 110.0' 1,900 60 113.0' 1,100
58 103.0' 1,700 112.0' 1,400 115.0' 1,400

ON OUTRIGGERS MID EXTENDED 18' 1/2"(5.5m) SPREAD

360o ROTATION
139.8'(42.6m) Boom(telescoping mode II) + 33.2' (10.1m) Jib 139.8'(42.6m) Boom(telescoping mode II) + 58.1' (17.7m) Jib
C 3 5o offset 25o offset 45o offset C 3 5o offset 25o offset 45o offset
R W R W R W R W R W R W
80 32.7' 11,700 45.8' 11,600 53.0' 10,000 80 40.8' 7,300 64.6' 6,500 77.3' 5,200
79 36.4' 11,700 49.0' 11,200 55.8' 9,800 79 44.7' 7,300 67.9' 6,400 80.4' 5,100
78 39.6' 11,700 52.1' 10,900 59.1' 9,600 78 48.7' 7,300 72.0' 6,200 83.5' 5,100
77 43.0' 11,700 55.0' 10,600 61.6' 9,400 77 52.6' 7,300 75.2' 6,100 86.2' 5,000
76 46.4' 11,700 57.7' 10,300 64.1' 9,200 76 56.5' 7,300 78.1' 6,000 89.2' 5,000
75 49.4' 11,700 60.9' 10,100 67.0' 9,100 75 60.0' 7,300 81.8' 5,900 92.4' 5,000
73 55.8' 11,500 67.0' 9,500 72.6' 8,700 73 67.0' 7,300 88.2' 5,700 97.7' 4,900
70 64.6' 10,200 74.9' 8,600 79.7' 7,800 70 78.3' 7,300 97.5' 5,400 105.0' 4,700
68 69.3' 8,500 79.7' 7,300 84.0' 6,700 68 83.8' 6,100 103.0' 5,000 110.0' 4,400
65 76.8' 6,600 86.4' 5,800 90.4' 5,400 65 91.6' 4,600 110.0' 3,900 116.0' 3,400
63 81.8' 5,600 91.1' 4,900 94.7' 4,600 63 97.1' 3,800 114.0' 3,200 120.0' 2,800
60 89.1' 4,300 97.6' 3,800 101.0' 3,600 60 105.0' 2,800 121.0' 2,400 127.0' 2,100
58 93.6' 3,600 102.0' 3,200 105.0' 3,000 58 110.0' 2,200 126.0' 1,900 131.0' 1,700
55 101.0' 2,700 108.0' 2,400 111.0' 2,300 55 118.0' 1,500 133.0' 1,300 137.0' 1,200
53 105.0' 2,200 113.0' 2,000 115.0' 1,900 53 123.0' 1,100
50 111.0' 1,500 119.0' 1,400 120.0' 1,300
48 116.0' 1,100 122.0' 1,000 124.0' 1,000

ON OUTRIGGERS MID EXTENDED 18' 1/2"(5.5m) SPREAD

360o ROTATION
125.5'(38.3m) Boom(telescoping mode I) + 33.2' (10.1m) Jib 125.5'(38.3m)Boom(telescoping mode I) + 58.1' (17.7m) Jib
C 3 5o offset 25o offset 45o offset C 3 5o offset 25o offset 45o offset
R W R W R W R W R W R W
80 30.5' 14,600 43.5' 14,000 50.1' 10,700 80 37.2' 8,800 58.7' 7,000 71.2' 5,200
79 33.3' 14,600 46.0' 13,600 52.6' 10,600 79 41.2' 8,800 61.5' 6,800 73.9' 5,100
78 36.0' 14,600 49.2' 13,300 55.1' 10,500 78 44.8' 8,800 65.4' 6,700 76.8' 5,100
77 39.0' 14,600 51.7' 12,900 57.6' 10,300 77 47.8' 8,800 68.4' 6,500 79.5' 5,000
76 42.6' 14,600 54.1' 12,700 60.1' 10,200 76 51.3' 8,800 70.8' 6,400 82.1' 5,000
75 45.5' 14,600 56.9' 12,400 62.7' 10,100 75 54.9' 8,800 74.3' 6,300 84.9' 5,000
73 51.2' 14,600 62.4' 11,900 67.5' 10,000 73 61.6' 8,800 80.5' 6,100 90.0' 4,900
70 58.2' 11,300 68.9' 9,500 73.7' 8,600 70 71.3' 8,300 88.9' 5,800 97.5' 4,700
68 63.0' 9,500 73.2' 8,100 77.8' 7,400 68 76.1' 6,900 94.0' 5,500 102.0' 4,600
65 69.9' 7,300 79.6' 6,300 83.5' 5,900 65 84.0' 5,200 101.0' 4,200 108.0' 3,900
63 74.5' 6,100 83.7' 5,400 87.5' 5,000 63 89.2' 4,300 105.0' 3,500 112.0' 3,300
60 81.0' 4,700 90.0' 4,200 93.5' 3,900 60 96.6' 3,100 112.0' 2,600 118.0' 2,500
58 85.4' 3,900 93.9' 3,500 97.1' 3,300 58 102.0' 2,500 116.0' 2,100 122.0' 2,000
55 91.8' 2,900 99.7' 2,600 103.0' 2,500 55 108.0' 1,700 123.0' 1,400 128.0' 1,400
53 95.7' 2,300 104.0' 2,100 106.0' 2,000 53 113.0' 1,200 127.0' 1,000 131.0' 1,000
50 102.0' 1,600 109.0' 1,500 111.0' 1,400
48 105.0' 1,100 113.0' 1,100 114.0' 1,000

C :Loaded boom angle (o)

R :Load radius in feet
W :Rated lifting capacity in pounds

12
5
12
STANDARD EQUIPMENT GR-1000XL RATED LIFTING CAPACITIES (IN POUNDS)
- Five section full power partially synchronized boom - Independently controlled outriggers
39.4'~154.2' (12.0 m~47.0 m) - Four outrigger extension positions ON OUTRIGGERS MIN EXTENDED 8' 10-5/16"(2.7m) SPREAD
o
- 33.2' or 58.1' (10.1 m or 17.7 m) bi-fold lattice jib (tilt type) - Self-storing outrigger pads 360 ROTATION
with 3.5o, 25o or 45o pinned offsets and self storing pins. - Mitsubishi 6M60-TLA3B turbo charged after cooled engine A 39.4' 53.7' 68.1'(20.8m) 82.4'(25.1m) 96.8'(29.5m) 111.1'(33.9m) 125.5'(38.3m) 139.8'(42.6m) 154.2'
- Auxiliary lifting sheave (single top) stowable (267HP) with exhaust brake B C (12m) C (16.4m) C C C C C C C C C C C C C (47m)
8' 73 143,900 78 102,700
- Variable speed main hoist with grooved drum, cable follower - Electronic controlled automatic transmission driven
10' 70 94,900 76 93,000 80 90,200 79 40,100
and 820' of 3/4" cable. by torque converter 12' 66 66,900 73 65,200 78 63,700 77 40,100
- Variable speed auxiliary hoist with grooved drum, cable follower - 4 X 4 X 4 drive/steer 15' 61 44,700 70 43,400 75 42,000 75 40,100 78 42,500 78 35,500
and 456' of 3/4" cable. - Non-spin rear differential 20' 52 26,300 64 25,400 70 24,300 70 30,400 74 26,400 74 31,000 77 27,500 77 31,400 79 28,300 79 31,700
- 2-speed hoist - Automatic rear axle oscillation lockout system 25' 41 17,000 57 16,100 65 15,300 65 20,900 70 17,200 70 21,500 74 18,200 74 21,800 76 18,900 76 22,100 78 19,500 78 22,300
- Drum rotation indicator (audible,visible and thumper type) main - 29.5-25 34PR tires 30' 25 11,400 50 10,400 60 9,600 60 14,900 66 11,600 66 15,700 70 12,500 70 16,000 73 13,200 73 16,200 75 13,800 76 16,400 78 14,100 78 15,300
and auxiliary hoist - Disc brakes 35' 42 6,600 55 5,800 55 10,900 62 7,700 62 11,600 67 8,700 67 12,100 70
9,400 70 12,300 73 9,900 73 12,500 75 10,300 76 11,400 77 10,500
40' 33 3,900 49 3,100 49 8,100 58 4,900 58 8,700 63 5,900 9,200 67 6,600
64 68 9,500 70 7,100 71 9,600 73 7,500 73 8,600 75 7,700
- Anti-Two block device (overwind cutout) - Fenders
45' 18 1,800 43 1,100 43 5,900 53 2,800 53 6,500 60 3,700
60 7,000 64 4,500 64 7,300 68 5,000 68 7,500 71 5,400 71 6,500 73 5,600
- Boom angle indicator - Air dryer
50' 36 4,300 49 1,100 49 4,900 56 2,100
56 5,300 61 2,800 61 5,600 65 3,300 65 5,800 68 3,700 69 4,800 71 4,000
- Tadano electronic load moment indicator system (AML-C) - Water separator with filter(high filtration) 55' 27 2,900 44 3,500 53 3,900 58 1,500 58 4,200 63 2,000 63 4,400 66 2,400 66 3,500 69 2,700
- Outrigger extension length detector - Engine over-run alarm 60' 13 1,900 38 2,400 49 2,800 55 3,100 60 3,300 64 1,300 64 2,300 67 1,500
- Electronic crane monitoring system - Back-up alarm 65' 31 1,500 44 1,900 52 2,200 57 2,300 62 1,400
o
- Tadano twin swing system and 360 positive swing lock - Low oil pressure/high water temp. warning device (visual) 70' 40 1,100 48 1,400 54 1,500
- Self centering finger control levers with pilot control - Rear steer centering light D 0 28 0 44 5 49 35 55 45 58 52 62 57 65
- Control pedals for boom elevating and boom telescoping - Air cleaner dust indicator Telescoping conditions (%)
Tele.
- 3 way adjustable cloth seat with armrests, high back - Full instrumentation package mode
I, II I I II I II I II I II I II I II I, II
and seat belt - Complete highway light package 2nd boom 0 50 100 0 100 0 100 0 100 0 100 0 100 50 100
- Tilt-telescoping steering wheel - Tool storage compartment 3rd boom 0 0 0 33 16 50 33 66 50 83 66 100 83 100 100
- Tinted safety glass and sun visor - Tire inflation kit 4th boom 0 0 0 33 16 50 33 66 50 83 66 100 83 100 100
- Front windshield wiper and washer - 24 volt electric system Top boom 0 0 0 33 16 50 33 66 50 83 66 100 83 100 100
- Roof window wiper and washer - 7.3 ton (6.6 metric ton) hook with swivel
- Power window (cab door ) - 100 ton (90.7 metric ton) - 8 sheave with swivel hook and LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE ON OUTRIGGERS MIN EXTENDED
- Rear view mirrors (right and left side) safety latch for 3/4"(19mm) wire rope 8' 10-5/16"(2.7m)SPREAD 360 o ROTATION
A 39.4' 53.7' 68.1'
- Mirror for main and auxiliary hoists - Towing hooks-Front and rear
C B (12m) B (16.4m) B (20.8m)
- Cigarette lighter and ashtray - Lifting eyes 0 32.2' 9,200 46.5' 1,300 60.8' 1,700
- Cab floor mat - Hook block tie down (front bumper) Tele.
I, II I II
- Pump disconnect in operator's cab - Weighted hook storage compartment mode
- Hydraulic oil cooler - Halogen head lamp
- Hot water cab heater and air conditioner - Telecommunications terminal (HELLO-NET Owners Site)
A :Boom length in feet
- Positive control - Fuel consumption monitor
B :Load radius in feet
- Quick reeving type bi-fold jib o
C :Loaded boom angle ( )
- Work lights o
D :Minimum boom angle ( ) for indicated length (no load)

NOTE:The lifting capacity data stored in the LOAD MOMENT INDICATOR (AML-C) is based on the standard
number of parts of line listed in the chart.
Standard number of parts of line for each boom length should be according to the following table.

HOISTING PERFORMANCE Boom length in feet 39.4' 39.4' to 68.1' 68.1' to 154.2' Single top
(meters) (12m) (12m to 20.8m) (20.8m to 47m) Jib
LINE SPEEDS AND PULLS DRUM WIRE ROPE CAPACITIES Telescoping mode I, II I II I, II I, II
Main or auxiliary hoist - 14'-1/4" (0.362m) drum Main and auxiliary drum grooved lagging Number of parts of line 16 8 4 4 1
Wire
Layer Line speeds1 Line pulls Available2 rope 3/4" (19mm) wire rope
Low High Low High Rope per layer Total wire rope
layer
F.P.M. m/min F.P.M. m/min Lbs. kgf Lbs. kgf Feet Meters Feet Meters
1st 278 84 387 118 21,550 9,770 15,470 7,020 1 112.2 34.2 112.2 34.2
2nd 302 92 421 128 19,510 8,850 14,010 6,350 2 122.3 37.3 234.5 71.5
3rd 327 99 456 139 17,830 8,090 12,800 5,810 3 132.2 40.3 366.8 111.8
4th 352 107 491 149 16,420 7,450 11,790 5,350 4 142.3 43.4 509.1 155.2
5th 377 115 526 160 15,210 6,900 10,920 4,950 5 152.2 46.4 661.4 201.6
6th 402 122 560 170 14,170 6,430 10,170 4,610 6 162.4 49.5 823.8 251.1
7th3 427 130 595 181 13,260 6,010 9,520 4,320 7 172.5 52.6 996.4 303.7
* Maximum permissible line pull may be affected by wire rope strength.
Wire rope strength (7x35 class) = 14,600lbs (6,600kg)
DRUM DIMENSIONS
1
Line speeds based only on hook block, not loaded. Inch mm
2
Developed by machinery with each layer of wire rope, but not based Root diameter 14-1/4" 362
on rope strength or other limitation in machinery or equipment. Length 23-5/8" 600
3
Seventh layer of wire rope are not recommended Flange diameter 25-7/8" 657
for hoisting operations.

4 13
4
13
 Tadano electronic LOAD MOMENT INDICATOR system TADANO AML-C monitors outrigger extended length and
WARNING AND OPERATING INSTRUCTIONS (AML-C) including: automatically programs the corresponding "RATED LIFTING

FOR LIFTING CAPACITIES Control lever lockout function

Boom position indicator
CAPACITIES" table

Outrigger state indicator Operator's right hand console includes transmission gear
GENERAL Boom angle / boom length / jib offset angle / jib length / load selector and sight level bubble. Upper console includes
1. RATED LIFTING CAPACITIES apply only to the machine as 9. When boom length is between values listed, refer to the radius / rated lifting capacities / actual loads read out working light switch, roof washer and wiper switch
originally manufactured and normally equipped by TADANO rated lifting capacities of the next longer and next shorter Ratio of actual load moment to rated load moment emergency outrigger set up key switch,
LTD. Modifications to the machine or use of optional booms for the same radius. The lesser of the two rated lifting indication jib equipped/removed select switch, eco mode switch,
equipment other than that specified can result in a reduction capacities shall be used. Automatic Speed Reduction and Soft Stop function high speed hoist (main / aux) switch,
of capacity. 10. When making lifts at a load radius not shown, use the next on boom elevation and swing boom emergency telescoping switch (2nd and 3rd/4th/top)
2. Hydraulic cranes can be hazardous if improperly longer radius to determine allowable capacity.
Working condition register switch and air conditioning control switch. Swing lock lever.
operated or maintained. Operation and maintenance of this 11. Load per line should not exceed 14,600 lbs. (6,600kg) for
machine must be in compliance with information in the main hoist and auxiliary hoist.
Load radius / boom angle / tip height / swing range
Operation and Maintenance Manual supplied with 12. Check the actual number of parts of line with LOAD MOMENT preset function NOTE: Each crane motion speed is based on unladen
the crane. If this manual is missing, order a replacement INDICATOR (AML-C) before operation. Maximum lifting External warning lamp conditions.
through the distributor. capacity is restricted by the number of parts of line of LOAD Tare function
3. The operator and other personnel associated with this MOMENT INDICATOR (AML-C). Limited capacity is as Fuel consumption monitor
machine shall fully acquaint themselves with the latest determined from the formula, Single line pull for main hoist Main hoist / auxiliary hoist select
OSHA 29 CFR Part 1926 crane safety standards. 14,600 lbs.(6,600kg) x number of parts of line. Drum rotation indicator (audible and visible type) main and
13. The boom angle before loading should be greater to account auxiliary hoist
for deflection. For rated lifting capacities, the loaded boom
SET UP angle and the load radius is for reference only.
1. Rated lifting capacities on the load chart are the maximum
allowable crane capacities. They are based on the machine
14. The 39.4' (12.0m) boom length capacities are based on boom
fully retracted. If not fully retracted [less than 53.7'(16.38m) CARRIER SPECIFICATIONS
standing level on firm supporting surface under ideal job boom length], use the rated lifting capacities for the 53.7' (16.38m)
conditions. Depending on the nature of the supporting boom length. TYPE - Rear engine, left hand steering, driving axle 2-way SUSPENSION - Front: Rigid mounted to frame. Rear: Pivot
surface, it may be necessary to have structural supports 15. Extension or retraction of the boom with loads may be selected type by manual switch, 4x2 front drive, 4x4 front and mounted with hydraulic lockout device.
under the outrigger floats or tires to spread the loads to a attempted within the limits of the RATED LIFTING CAPACITIES. rear drive.
larger surface. The ability to telescope loads is limited by hydraulic pressure, BRAKE SYSTEMS - Service: Air over hydraulic disc brakes on
2. For outrigger operation, outriggers shall be properly extended boom angle, boom length, crane maintenance, etc. FRAME - High tensile steel, all welded mono-box construction. all 4 wheels. Parking/Emergency: Spring applied-air released
with tires free of supporting surface before operating crane. 16. For lifting capacity of single top, reduce the rated lifting
brake acting on input shaft of front axle. Auxiliary: Electro-
capacities of relevant boom according to a weight reductions TRANSMISSION - Electronically controlled full automatic pneumatic operated exhaust brake.
OPERATION for auxiliary load handling equipment. Capacities of single top
transmission. Torque converter driving full powershift with
1. Rated lifting capacities have been tested to and meet shall not exceed 14,600 lbs. (6,600kg) including main hook.
driving axle selector. 6 forward and 2 reverse speeds, constant TIRES - 29.5-25 34PR(OR)
minimum requirements of SAE J1063-Cantilevered Boom 17. When base jib or top jib or both jib removing, jib state switch
Crane Structures Method of Test. select removed. mesh.
3 speeds - high range - 2 wheel drive; 4 wheel drive OUTRIGGERS - Four hydraulic, beam and jack outriggers.
2. Rated lifting capacities do not exceed 85 % of the tipping 18. When erecting and stowing jib, be sure to retain it by hand or by
load on outriggers fully extended as determined by SAE other means to prevent its free movement. 3 speeds - low range - 4 wheel drive Vertical jack cylinders equipped with integral holding valve. Each
J765-Crane Stability Test Code. 19. Use "ANTI-TWO BLOCK" disable switch when erecting and outrigger beam and jack is controlled independently from cab.
Rated lifting capacities for partially extended outriggers are stowing jib and when stowing hook block. While the switch is TRAVEL SPEED - 22 mph (36 km/h) Beams extend to 23' 11-3/8" (7.3 m) center-line and retract to
determined from the formula, Rated Lifting Capacities pushed, the hoist does not stop, even when overwind condition within 10' 10-1/2" (3.315 m) overall width with floats. Outrigger
=(Tipping Load - 0.1 x Tip Reaction)/1.25. occurs. AXLE - Front: Full floating type, steering and driving axle with jack floats are attached thus eliminating the need of manually
3. Rated lifting capacities above bold lines in the chart are 20. For boom length with 33.2' (10.1m) jib, rated lifting capacities are planetary reduction. Rear: Full floating type, steering and driving attaching and detaching them. Controls and sight bubble located
based on crane strength and those below, on its stability. determined by loaded boom angle only in the column headed axle with planetary reduction and non-spin rear differential. in superstructure cab. Four outrigger extension lengths are
They are based on actual load radius increased by boom "154.2' (47.0m) boom + 33.2' (10.1m) jib". provided with corresponding "RATED LIFTING CAPACITIES" for
deflection. For boom length with 58.1' (17.7 m) jib, rated lifting capacities STEERING- Hydraulic power steering controlled by steering crane duty in confined areas.
4. The weight of handling device such as hook blocks, slings, are determined by loaded boom angle only in the column wheel. Four steering modes available: 2 wheel front, 2 wheel Min. Extension 8' 10-5/16"(2.7m) center to center
etc., must be considered as part of the load and must be headed "154.2' (47.0m) boom + 58.1' (17.7m) jib". rear, 4 wheel coordinated and 4 wheel crab . Mid. Extension 18' 1/2"(5.5m) center to center
deducted from the lifting capacities. For angles not shown, use the next lower loaded boom angle
Mid. Extension 21' 11-3/4"(6.7m) center to center
5. Rated lifting capacities are based on freely suspended loads to determine allowable capacity.
Max. Extension 23' 11-3/8"(7.3m) center to center
and make no allowance for such factors as the effect of wind, 21. When lifting a load by using jib (aux. hoist) and boom (main
Float size(Diameter) 1' 11- 5/8" (0.6m)
sudden stopping of loads, supporting surface conditions, hoist) simultaneously, do the following:
inflation of tires, operating speeds, side loads, etc. Side pull Enter the operation status as jib operation, not as boom
on the boom or jib is extremely dangerous. operation.
6. Rated lifting capacities do not account for wind on lifted load Before starting operation, make sure that mass of load is ENGINE
or boom. We recommend against working under the condition within rated lifting capacity for jib. Model Mitsubishi 6M60-TLA3B Radiator Fin and tube core, thermostat controlled
Type Direct injection diesel Fan, in.(mm) Suction type, 6-blade, 23.6 (600) dia.
that the load is out of control due to a strong wind.During
No. of cylinders 6 Starting 24 volt
boom lift, consider that the rated lifting capacity is reduced by DEFINITIONS Combustion 4 cycle, turbo charged and after cooled Charging 24 volt system, negative ground
50% when the wind speed is 20mph(9m/s) to 27mph(12m/s); 1. Load Radius: Horizontal distance from a projection of the axis BoreXStroke, in.(mm) 4.646 X 4.528 (118X115) Battery 2-120 amp. Hour
reduced by 70% when the wind speed is 27mph(12m/s) to of rotation to supporting surface before loading to the center of Displacement, cu. in (liters) 460 (7.54) Compressor, air, CFM(l /min) 29 CFM (830) at 2,600rpm
31mph(14m/s).If the wind speed is 31mph(14m/s) or over, the vertical hoist line or tackle with load applied. Air inlet heater 24 volt preheat Horsepower (kW) Gross 267 (200) at 2,600rpm
stop operation. During jib lift, stop operation if the wind speed 2. Loaded Boom Angle: The angle between the boom base Air cleaner Dry type, replaceable element Torque, Max. ft-lb (kgm) 579 (80) at 1,400rpm
is 20mph(9m/s) section and the horizontal, after lifting the rated lifting capacity Oil filter Full flow with replaceable element Capacity, gal.(liters)
7. Rated lifting capacities at load radius shall not be exceeded. at the load radius. Fuel filter Full flow with replaceable element Cooling water 3.4 (13)
Fuel tank, gal.(liters) 79.2 (300), right side of carrier Lubrication 3.4 ~ 4.0 (13 ~ 15)
Do not tip the crane to determine allowable loads. 3. Working Area: Area measured in a circular arc about the
Cooling Liquid pressurized, recirculating by-pass Fuel 79.2 (300)
8. Do not operate at boom lengths, radii, or boom angle, where centerline of rotation.
no capacities are shown. Crane may overturn without any 4. Freely Suspended Load: Load hanging free with no direct
load on the hook. external force applied except by the hoist line.
5. Side Load: Horizontal side force applied to the lifted load either
on the ground or in the air.

14 3
3
14
CRANE SPECIFICATIONS GR-1000XL RATED LIFTING CAPACITIES (IN POUNDS)
BOOM WIRE ROPE - Non-rotating 3/4"(19mm) 7X35 class. ON RUBBER
Five section full power synchronized telescoping boom, Breaking Strength 72,800lbs(33,000kg) A Stationary Creep
39.4'~154.2' (12.0m~47.0m), of round box construction Over Front 360o Rotation Over Front
with seven sheaves, 17-5/16" (0.44m) root diameter, at boom head. HOOK BLOCKS 39.4' 68.1' 96.8' 39.4' 68.1' 96.8' 39.4' 68.1' 96.8'
B C (12m) C (20.8m) C (29.5m) C (12m) C (20.8m) C (29.5m) C (12m) C (20.8m) C (29.5m)
The synchronization system consists of two telescope cylinders, 100 ton (90.7 metric ton)-8sheaves with swivel hook and safety latch. 12' 66 60,000 66 38,000 66 45,000
an extension cable and retraction cable. Hydraulic cylinder fitted 7.3 ton (6.6 metric ton) - Weighted hook with swivel and safety latch. 15' 61 49,600 61 28,500 61 36,600
with holding valve. Two easily removable wire rope guards, rope 20' 52 37,500 70 35,000 52 17,500 70 20,000 52 26,800 70 29,200
dead end provided on both sides of boom head. Boom telescope 25' 41 28,500 65 29,500 74 28,500 40 10,400 65 14,000 73 14,000 40 20,500 65 22,800 74 23,400
30' 25 21,500 60 24,000 71 24,000 25 6,500 60 9,500 70 10,000 25 15,600 60 18,200 71 18,900
sections are supported by wear pads both vertically and horizontally. HYDRAULIC SYSTEM
35' 55 19,200 67 19,500 55 6,500 67 7,400 55 14,800 67 15,500
Extension speed 114.8 in 160 seconds. 40' 49 15,200 64 16,000 49 4,500 63 5,400 49 12,000 64 12,900
PUMPS - Two variable piston pumps for crane functions. 45' 43 12,200 60 13,000 43 3,000 60 3,900 43 9,800 60 10,600
BOOM ELEVATION - By a double acting hydraulic cylinder with Tandem gear pump for steering, swing and optional equipment. 50' 36 9,700 57 10,600 36 1,800 56 2,700 36 7,900 57 8,900
o o
holding valve. Elevation -1.5 ~80.5 , combination controls for hand Powered by carrier engine. Pump disconnect for crane is 55' 27 8,000 53 8,800 53 1,700 27 6,500 53 7,300
60' 13 6,500 49 7,400 13 5,200 49 6,100
or foot operation. Boom angle indicator. engaged/ disengaged by rotary switch from operator's cab. 65' 45 6,100 44 5,000
Automatic speed reduction and soft stop function. 70' 40 5,000 40 4,100
o o
Boom raising speed 20 to 60 in 46 sec. CONTROL VALVES - Multiple valves actuated by pilot pressure 75' 35 4,100 34 3,200
with integral pressure relief valves. 80' 28 3,400 28 2,500
o o o 85' 20 2,700
JIB - Two stage bi-fold lattice type with 3.5 , 25 or 45 offset (tilt type).
D 0 0 28 45 0
Single sheave, 15-5/8"(0.396m) root diameter, at the head of both RESERVOIR - 222 gallon (840 lit.) capacity. External sight level
Telescoping conditions (%)
jib sections. Stored alongside base boom section. Jib length is gauge. Tele.
mode
I, II II II I, II II II I, II II II
33.2' (10.1m) or 58.1' (17.7m). Assistant cylinders for mounting
2nd boom 0 0 0 0 0 0 0 0 0
and stowing, controlled at right side of superstructure. FILTRATION - BETA10=10 return filter, full flow with bypass
3rd boom 0 33 66 0 33 66 0 33 66
Self stowing jib mounting pins. protection, located inside of hydraulic reservoir. Accessible for 4th boom 0 33 66 0 33 66 0 33 66
easy replacement. Top boom 0 33 66 0 33 66 0 33 66
AUXILIARY LIFTING SHEAVE (SINGLE TOP)
Single sheave, 15-5/8"(0.396m) root diameter. Mounted to main OIL COOLER - Air cooled fan type. LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE ON RUBBER OPERATION
A Stationary Creep
boom head for single line work (stowable).
Over Front 360o Rotation Over Front
39.4' 68.1' 96.8' 39.4' 39.4' 68.1' 96.8'
ANTI-TWO BLOCK - Pendant type over-winding cut out device CAB AND CONTROLS C B (12m) B (20.8m) B (29.5m) B (12m) B (12m) B (20.8m) B (29.5m)
with audio-visual (FAILURE lamp/BUZZER) warning system. 0 32.2' 19,300 60.8' 6,300 89.1' 2,100 32.2' 5,100 32.2' 14,100 60.8' 5,000 89.1' 1,400
Both crane and drive operations can be performed from one cab
A :Boom length in feet
SWING mounted on rotating superstructure.
B :Load radius in feet
Hydraulic axial piston motor through planetary swing speed
o C :Loaded boom angle (o)
reducer. Continuous 360 full circle swing on ball bearing turn Left side, 1 man type, steel construction with sliding door access D :Minimum boom angle (o) for indicated length (no load)
-1
table at 1.5min {rpm}. Equipped with manually locked/released and safety glass windows opening at side. Door window is
o NOTE: The lifting capacity data stored in the LOAD MOMENT INDICATOR (AML-C) is based
swing brake. A 360 positive swing lock for pick and carry and travel powered control. Windshield glass window and roof glass window
on the standard number of parts of line listed in the chart.
modes, manually engaged in cab. Twin swing system: Free swing are shatter-resistant. Tilt-telescoping steering wheel. Adjustable
Standard number of parts of line for rubber operation should be according to the
or lock swing controlled by selector switch on front console. control lever stands for swing, boom hoist, boom telescoping, following table.
auxiliary hoist and main hoist. Control lever stands can change
HOIST neutral positions and tilt for easy access to cab. 3 way adjustable Boom length in feet 39.4' 39.4' to 96.8' Single top
operator's seat with high back, headrest and armrest. Engine (meters) (12m) (12m to 29.5m) Jib
Number of parts of line 6 4 1
MAIN HOIST - Variable speed type with grooved drum driven by throttle knob. Foot operated controls: boom elevating,
hydraulic axial piston motor through speed reducer. Power load boom telescoping, service brake and engine throttle.
lowering and raising. Equipped with automatic brake (neutral brake) Hot water cab heater and air conditioning.
and counterbalance valve. Controlled independently of auxiliary hoist.
Equipped with cable follower and drum rotation indicator. Dash-mounted engine start/stop, monitor lamps, cigarette lighter,
WARNING AND OPERATING INSTRUCTIONS
drive selector switch, parking brake switch, steering mode FOR ON RUBBER LIFTING CAPACITIES
DRUM - Grooved 14-1/4"(0.362m) root diameter x 23-5/8"(0.6m) select switch, power window switch, pump engaged/disengaged
wide. Wire rope: 820' of 3/4"diameter rope (250m of 19mm). switch, swing brake switch, telescoping/auxiliary hoist select 1. Rated lifting capacities on rubber are in pounds and do not exceed 6. Over front operation shall be performed within two degrees in front of
Drum capacity: 997' (304m) 7 layers. Maximum single line pull: switch, outrigger controls, free swing / lock swing selector switch, 75 % of tipping loads as determined by SAE J765-Crane Stability chassis.
Test Code. 7. On rubber lifting with "jib" is not permitted. Maximum permissible
1st layer 21,550 lbs (9,770kg). Maximum permissible line pull eco mode switch, high speed hoist (main/aux) switch and ashtray. 2. Rated lifting capacities shown in the chart are based on condition boom length is 96.8 ft. (29.5m).
wire strength: 14,600 lbs (6,600kg). that crane is set on firm level surfaces with axle oscillation lockout 8. When making lift on rubber stationary, set parking brake.
applied. Those above bold lines are based on tire capacity and 9. For creep operation, boom must be centered over front of machine,
AUXILIARY HOIST - Variable speed type with grooved drum driven Instruments - Torque converter oil temperature, engine water those below, on crane stability. They are based on actual load swing lock engaged, and load restrained from swinging. Travel slowly
by hydraulic axial piston motor through speed reducer. Power load temperature, air pressure, fuel, speedometer, tachometer, radius increased by tire deformation and boom deflection. and keep the lifted load as close to the ground as possible, and
3. If the axle oscillation lockout cylinders contain air, the axle will not especially avoid any abrupt steering, accelerating or braking.
lowering and raising. Equipped with automatic brake (neutral brake) hour meter and odometer / tripmeter. Hydraulic oil pressure is be locked completely and rated lifting capacities may not be 10. Do not operate the crane while carrying the load.
and counterbalance valve. Controlled independently of main hoist. monitored and displayed on the AML-C display panel. obtainable. Bleed the cylinders according to the operation safety 11. Creep is motion for crane not to travel more than 200 ft. (60 m) in any
Equipped with cable follower and drum rotation indicator. and maintenance manual. 30 minute period and to travel at the speed of less than 1 mph
4. Rated lifting capacities are based on proper tire inflation, capacity (1.6km/h).
DRUM - Grooved 14-1/4"(0.362m) root diameter x 23-5/8"(0.6m) and condition. Damaged tires are hazardous to safe operation of 12. For creep operation, choose the driv e mode and proper gear
crane. according to the road or working condition.
wide. Wire rope: 456' of 3/4"diameter rope (139m of 19mm). 5. Tires shall be inflated to correct air pressure.
Drum capacity: 997' (304m) 7 layers. Maximum single line pull: Tires Air Pressure
1st layer 21,550 lbs (9,770kg). Maximum permissible line pull 29.5-25 34PR 57 psi (4.0 kgf/cm2)
wire strength: 14,600 lbs (6,600kg).

2 15
2
15
WARNING AND OPERATING INSTRUCTIONS
FOR USING THE LOAD MOMENT INDICATOR (AML-C)
1. When operating crane on outriggers: When a load is lifted in the front position and then swung
Set P.T.O. switch to "ON". to the side area, make sure the value of the LOAD
Press the outrigger mode select key to register for the MOMENT INDICATOR(AML-C) is below the 360o lifting
outrigger operation. Press the register key, then the outrigger capacity.
mode indicative symbol changes from flashing to a solid light. (2) For creep operation.

GR-1000XL-2
Press the lift mode select key to select the lift status that The creep capacities are attainable only when boom is
corresponds to the actual boom configuration. in the straight forward position of chassis and the over
Each time the lift mode select key is pressed, the status changes. front position symbol is on. If boom is not in the straight
Press the register key to register the lift status, then the lift forward position of chassis , never lift load.
indicative symbol changes from flashing to a solid light. 3. A swing does not automatically stop even if the crane
when mounting and stowing jib, select the jib set status. becomes overloaded.
(the jib state indicative symbol will be flashing.)
2. When operating crane on rubber:
4. During crane operation, make sure that the displays on front
panel are in accordance with actual operating conditions.
100 Ton Capacity (90.7 Metric Tons)
Set P.T.O. switch to "ON". 5. The displayed values of LOAD MOMENT INDICATOR
Press the outrigger mode select key. The on-tire mode (AML-C) are based on freely suspended loads and make no
indicative symbol comes on. Each time the outrigger mode
select key is pressed the status changes. Select the creep
allowance for such factors as the effect of wind, sudden
stopping of loads, supporting surface conditions, inflation of
HYDRAULIC ROUGH TERRAIN CRANE
operation, the on-tire mode indicative symbol flicker. tire, operating speed, side loads, etc.
Press the lift mode select key to register the boom or single top For safe operation, it is recommended when extending and
lift.
However, pay attention to the following.
lowering boom or swinging, lifting loads shall be
appropriately reduced.
DIMENSIONS
(1) For stationary operation. 6. LOAD MOMENT INDICATOR (AML-C) is intended as an aid
The front capacities are attainable only when the over front to the operator. Under no condition should it be relied upon
position symbol comes on. When the boom is more than to replace use of capacity charts and operating instruction.
2 degrees from centered over front of chassis, 360 o Sole reliance upon LOAD MOMENT INDICATOR (AML-C)
capacities are in effect. aids in place of good operating practice can cause an
accident. The operator must exercise caution to assure
safety.

GR-1000XL Axle weight distribution chart

Pounds Kilograms
GVW Front Rear GVW Front Rear
Base machine
115,235 57,300 57,935 52,270 25,990 26,280
Remove: 1. 7.3ton(6.6metric ton) hook ball -360 -515 155 -164 -233 69
2. 100ton(90.7metric ton) hook block -1,900 -3,665 1,765 -862 -1,664 802
3. Top jib -740 -990 250 -336 -450 114
4. Base jib -1,910 -3,755 1,845 -867 -1,704 837
5. Auxiliary lifting sheave -110 -330 220 -50 -149 99
6. Removable Counterweight -22,000 9,350 -31,350 -9,979 4,240 -14,219
(with Auxiliary Hoist & wire rope)

Note : Dimension is with boom angle at -1.5 degree.

TADANO AMERICA CORPORATION

4242 West Greens Road GENERAL DIMENSIONS
Houston, Texas 77066 U.S.A. (29.5 X 25 Tires)
PHONE: (281) 869-0030 EXT. 315 Feet Meters
FAX: (281) 869-0040 Turning radius
Parts Hotline: (281) 869-0033
4 wheel steer 22' 3-3/4" 6.8
Service Hotline: (281) 869-5925
2 wheel steer 39' 1/2" 11.9
Web site: www.tadanoamerica.com
E-mail: [email protected] Tail swing of counterweight 13' 8-15/16" 4.19
Form No. TAC-GR-1000-2-00101-FCTW-110210
Specifications are subject to change without notice.
16
16