Monitor G3 Manual Service V0 1 PDF

G3 Patient Monitor
Service Manual
GENERAL MEDITECH, INC.

Revision
Revision Date Changes
1.0 5/2009 First Issue
All Rights Reserved

This publication is protected by copyright and all rights are reserved. No part of this manual may
be reproduced or transmitted in any form or by any means, electronic or mechanical, for any
purpose, without the express written permission of GENERAL MEDITECH, INC. (hereinafter
called GMI).
Restrictions and Liabilities

Information in this document is subject to change and does not represent a commitment by GMI.
Changes made to the information in this document will be incorporated in new editions of the
publication. No responsibility is assumed by GMI for the use or reliability of software or
equipment that is not supplied by GMI or its affiliated dealers.
Warranty
G3 Multi-Parameter Patient Monitor is warranted by GMI for 1.5 years of free charge from the date
of the purchase, while the SpO 2 sensor, blood pressure cuff, ECG cable and body temperature
sensor is warranted for 1 year. The consumables are excluded from the scope of this warranty.
The following situations are not included in the scope of the warranty:
The serial number of the monitor was ripped off or unreadable; or
The monitor was damaged due to improper connection with other equipment; or
The monitor was damaged due to accident; or
The user modified the monitor without GMIs written authorization.
Contact
Manufacturer: GENERAL MEDITECH, INC.
Add: South Office 4/F, Kezhi Rd.W.No. 1, Science Park, Nanshan District, Shenzhen, Guangdong
P.R.China
Tel: 86-755-26500832
Fax: 86-755-26546285
Zip: 518057
Internet: http://www.szmedtech.com
E-mail: [email protected]
EC Authorized Representative: Peretti Service S.A.S

Add: P.Le Tecchio 49/F 80125 Napoli Italy P.Iva 04552071211
Tel: 081 195 73 824
Fax: 081 195 73 827
Contents
CHAPTER 1: OVERVIEW..................................................................................................................1
BRIEF INTRODUCTION............................................................................................................................1
SAFETY INFORMATION...........................................................................................................................1
CLASSIFICATION..........................................................................................................................1
PROHIBITION................................................................................................................................2
CAUTIONS......................................................................................................................................2
CONTRAINDICATIONS.............................................................................................................................3
FUNCTION...................................................................................................................................................3
CHAPTER 2: INTRODUCTION..........................................................................................................4
EXTERNAL APPEARANCE.......................................................................................................................4
G3C...................................................................................................................................................4
G3D..................................................................................................................................................7
G3F.................................................................................................................................................10
G3G................................................................................................................................................13
DISPLAY.....................................................................................................................................................16
BATTERIES................................................................................................................................................18
BATTERY MAINTENANCE........................................................................................................18
BATTERY RECYCLING..............................................................................................................19
CHAPTER 3: INSTALLATION..........................................................................................................20
UNPACKING AND CHECKING...............................................................................................................20

ENVIRONMENTAL REQUIREMENTS...................................................................................................21
INSTALLATION METHOD......................................................................................................................21
CONNECTING TO AC POWER SUPPLY...................................................................................21
INSTALLING THE BATTERY.....................................................................................................21
EQUIPOTENTIAL GROUNDING...............................................................................................22
CONNECTING PATIENT SENSORS AND PROBES.................................................................22
CONNECTING THE NETWORK CABLE..................................................................................22
CONNECTING TO VGA MONITOR...........................................................................................22
REPLACE THE FUSE...................................................................................................................23
POWERING ON THE MONITOR.............................................................................................................23
POWERING OFF THE MONITOR...........................................................................................................23
CHAPTER 4: MENU.........................................................................................................................24
MENU OPERATION..................................................................................................................................24
POPUP MENU...............................................................................................................................24
BROWSE MENU...........................................................................................................................24
EXIT MENU..................................................................................................................................24
DISPLAY.....................................................................................................................................................24
FIXED FORMAT...........................................................................................................................25
i
USER FORMAT.............................................................................................................................26
FORMAT SETUP...........................................................................................................................26
OXYCRG.......................................................................................................................................27
ALARM LIMIT.............................................................................................................................27
WAVEFORM SPEED....................................................................................................................27
OTHER SETTINGS.......................................................................................................................28
TOOLS........................................................................................................................................................29
REVIEW......................................................................................................................................................29
PATIENT.....................................................................................................................................................30
SYSTEM SETUP........................................................................................................................................30
SET TIME......................................................................................................................................30
REGION SETTINGS.....................................................................................................................31
NETWORK SETTINGS................................................................................................................32
MAINTENANCE...........................................................................................................................33
DEFAULT SETTINGS...................................................................................................................35
RECORDER SETUP..................................................................................................................................36
CHAPTER 5: ALARMS....................................................................................................................37
ALARM CATEGORIES.............................................................................................................................37
ALARM MODES........................................................................................................................................37
ALARM SETTINGS...................................................................................................................................37
SETTING ALARM VIA ALARM KEY........................................................................................37
SETTING ALARM VIA PARAMETER LABEL.........................................................................39
WHEN AN ALARM OCCURS..................................................................................................................40
CHAPTER 6: WAVEFORM FREEZING AND RECALLING............................................................41
OVERVIEW................................................................................................................................................41
FREEZING AND UNFREEZING..............................................................................................................41
WAVEFORM FREEZING.............................................................................................................41
WAVEFORM UNFREEZING.......................................................................................................41
WAVEFORM RECALLING.......................................................................................................................41
CHAPTER 7: PRINTING..................................................................................................................43
OVERVIEW................................................................................................................................................43
PRINTING TYPES.....................................................................................................................................43
REAL-TIME PRINTING...............................................................................................................43
TIMER PRINTING........................................................................................................................43
ALARM PRINTING......................................................................................................................43
WAVEFORM AND PARAMETER PRINTING........................................................................................44
INSTALLING PRINTER PAPER...............................................................................................................44
CHAPTER 8: TRENDS.....................................................................................................................45
OVERVIEW................................................................................................................................................45
TREND CHANNELS.................................................................................................................................45
TREND GRAPH CHANNEL........................................................................................................46
ii
TREND TABLE CHANNEL.........................................................................................................47
TREND WINDOWS...................................................................................................................................48
TREND GRAPH WINDOW.........................................................................................................48
TREND TABLE WINDOW...........................................................................................................50
CHAPTER 9: EVENTS.....................................................................................................................51
RECORD EVENTS....................................................................................................................................51
BROWSE EVENTS....................................................................................................................................51
CHAPTER 10: DRUG CALCULATOR.............................................................................................52
ENTER DRUG CALCULATOR................................................................................................................52

UNIT............................................................................................................................................................52
TERMS........................................................................................................................................................53
DRUG CALCULATOR..............................................................................................................................53
NUMERIC INPUT BLOCK..........................................................................................................53
CALCULATION FORMULA.......................................................................................................53
KNOWN ITEM AND CALCULATION RESULTS.....................................................................54
CALCULATION FOR ANY DRUG.............................................................................................54
CALCULATION FOR EXACT DRUG........................................................................................54
DRIP TABLE...............................................................................................................................................55
TITRATION TABLE...................................................................................................................................56
RESET.........................................................................................................................................................56
CHAPTER 11: OTHER PATIENT VIEWING....................................................................................57
OVERVIEW................................................................................................................................................57
SELECT MONITOR...................................................................................................................................57
OTHER PATIENT.......................................................................................................................................58
CHAPTER 12: ECG MONITORING.................................................................................................59
OVERVIEW................................................................................................................................................59
ECG MONITORING..................................................................................................................................59
PREPARATION.............................................................................................................................59
ELECTRODE PLACEMENT.......................................................................................................60
ECG CHANNEL.........................................................................................................................................62
MAIN LEAD CHANNEL.............................................................................................................62
OTHER LEAD CHANNELS........................................................................................................64
ECG PARAMETER....................................................................................................................................64
HEART RATE................................................................................................................................64
ST SEGMENT................................................................................................................................66
MAINTENANCE AND CLEANING.........................................................................................................67
TROUBLE SHOOTING.............................................................................................................................67
CHAPTER 13: RESP MONITORING...............................................................................................68
OVERVIEW................................................................................................................................................68
ELECTRODE PLACEMENT.....................................................................................................................68
iii
MONITORING INTERFACE....................................................................................................................69
RESP CHANNEL..........................................................................................................................69
RESPIRATION RATE...................................................................................................................70
PROMPT MESSAGES...............................................................................................................................70
CHAPTER 14: T-RESP MONITORING............................................................................................71
T-RESP CHANNEL....................................................................................................................................71
T-RESP MENU............................................................................................................................................71
CHAPTER 15: NIBP MONITORING.................................................................................................72
OVERVIEW................................................................................................................................................72
MONITORING PROCEDURE..................................................................................................................72
CUFF SELECTION AND PLACEMENT.................................................................................................72
MEASUREMENT LIMITATIONS............................................................................................................74
FUNCTIONS...............................................................................................................................................76
NIBP MEASUREMENT...............................................................................................................76
VENIPUNCTURE.........................................................................................................................77
TROUBLE SHOOTING.............................................................................................................................78
CHAPTER 16: TEMP MONITORING...............................................................................................79
TEMPERATURE PROBE INSTALLATION.............................................................................................79

TEMP PARAMETER..................................................................................................................................79
TEMP MENU..............................................................................................................................................80
CHAPTER 17: SPO2 MONITORING...............................................................................................82
OVERVIEW................................................................................................................................................82
PRECAUTIONS..........................................................................................................................................83
MEASUREMENT LIMITATIONS............................................................................................................84
MENU.........................................................................................................................................................84
SpO2 MENU..................................................................................................................................84
PLETH MENU...............................................................................................................................85
CHAPTER 18: IBP MONITORING..................................................................................................86
IBP CHANNELS.........................................................................................................................................86
IBP PARAMETER......................................................................................................................................87
PRECAUTIONS..........................................................................................................................................88
IBP MENU..................................................................................................................................................89
IBP PARAMETER MENU............................................................................................................89
iv
IBP CHANNEL MENU.................................................................................................................90
CLEANING OF IBP TRANSDUCER..........................................................................................91
STERILIZATION...........................................................................................................................91
CHAPTER 19: CO2 MONITORING..................................................................................................92
INTRODUCTION.......................................................................................................................................92
CO2 CHANNEL.............................................................................................................................93
CO2 PARAMETER........................................................................................................................94
CHAPTER 20: MAINTENANCE.......................................................................................................96
INSPECTION..............................................................................................................................................96
CLEANING.................................................................................................................................................96
DISINFECTION AND STERILIZATION.................................................................................................97
CHAPTER 21: LABELS, PACKAGING, TRANSPORT AND STORING.........................................98
LABELS......................................................................................................................................................98
PACKAGING..............................................................................................................................................99
TRANSPORT..............................................................................................................................................99
STORING....................................................................................................................................................99
APPENDIX A: PPRODUCT SPECIFICATIONS.............................................................................100
ENVIRONMENTAL SPECIFICATIONS................................................................................................100
POWER SOURCE SPECIFICATIONS....................................................................................................100
HARDWARE SPECIFICATIONS............................................................................................................101
DATA STORAGE......................................................................................................................................101
ECG SPECIFICATIONS...........................................................................................................................101
RESP SPECIFICATIONS.........................................................................................................................102
NIBP SPECIFICATIONS..........................................................................................................................102
TEMP SPECIFICATIONS........................................................................................................................103
SpO2 SPECIFICATIONS.........................................................................................................................103
PR SPECIFICATIONS..............................................................................................................................103
IBP SPECIFICATIONS.............................................................................................................................103
CO2 SPECIFICATIONS...........................................................................................................................103
APPENDIX B: EMC........................................................................................................................104
v
CHAPTER 1:
OVERVIEW
Welcome to use G3 Multi-Parameter Patient Monitor The main purpose of this manual is to
provide operating guide, instrument repair and maintenance information to users. The detailed
performance indexes, routine installation, operation and maintenance method as well as safety
information are illustrated in this manual. Before use, the serviceman shall carefully read this
manual in order to properly and correctly operate this monitor, so that it can reach specified safety
standards and performance indexes.
BRIEF INTRODUCTION
The G3 Multi-Parameter Patient Monitor is a multifunctional overall physiologic index monitor,
which is applicable to monitor the ECG, NIBP, SpO2, PR, RESP, TEMP, IBP and CO2 in hospitals.
This product has the multi-parameter function which can be selected, combined and configured by
the user according to his requirements (but the G3 Multi-Parameter Patient Monitor which you are
using probably only had part parameters and corresponding accessories selected by you when you
bought it).
This product is composed of main machine and corresponding functional accessories such as ECG
cable, blood pressure cuff, SpO2 sensor, body temperature sensor, BP hose, IBP sensor, dehydration
vase and sampling line.
This product has three input/output connectors for printer, network communication and external
VGA monitor.
SAFETY INFORMATION
CLASSIFICATION
According to the type of protection against electric shock:
----- CLASS I, INTERNALLY POWERED EQUIPMENT.
According to the degree of protection against electric shock:
----- TYPE BF APPLIED PART or TYPE CF APPLIED PART. The connector with a symbol
beside is TYPE BF APPLIED PART, the connector with a symbol beside is TYPE CF
APPLIED PART.
According to the degree of protection against ingress of water:
----- Not protected (ordinary).
According to the method(s) of sterilisation or disinfection recommended by the manufacturer.
----- Equipment with method(s) of sterilisation or disinfection recommended by the manufacturer.
According to the degree of safety of application in the presence of a FLAMMABLE
ANAESTHETIC MIXTURE WITH AIR or WITH OXYGEN OR NITROUS OXIDE:
----- EQUIPMENT not suitable for use in the presence of a FLAMMABLE ANAESTHETIC
MIXTURE.
According to the mode of operation:
----- CONTINUOUS OPERATION.
6
PROHIBITION
The marked symbol on the Monitor means: Attention, consult accompanying documents (this
manual).
Anywhere marked with in the manual, means when you using this equipment, you shall pay more
attention on it in order to guarantee the safety of the patient, operator or equipment.
WARNING
Do not use the G3 Multi-Parameter Patient Monitor for asphyxiation monitoring.
Do not use the G3 Multi-Parameter Patient Monitor during the magnetic resonance
imaging (MRI) or CT inspection process.
Do not use this monitor in the presence of inflammable anesthetics or gases.
CAUTIONS
WARNING
In order to make the monitor safe grounding, the hospital must provide the power
socket with complete wire under voltage, zero line and protective grounding in
accordance with national standard. Or the hospital bears all consequences.
To ensure patient safty, verify the divice and accessories can function safely and normally
before use.
Only qualified accessories can be used for the monitor.
The ECG cable uses five-lead or three-lead cable, and cannot be connected to other signal
terminals.
In order to avoid losing time for diagnosis and treatment, please configure adequate
alarm settings according to different conditions of each patient (for detailed setting
methods, refer to ALARM SETTINGS in CHAPTER 5).
When using this monitor, the F-type application section cannot be connected to other
conductivity or ground.
When using the electrosurgery unit during the monitoring, the loop of the electrosurgery
unit shall be properly connected to prevent from burning, even the life risk.
The monitor must be operated on battery power if the external wiring is in doubt.
When various equipments are connected to the same patient, pay attention to the danger
of leakage current overlap.
The Monitor has no defibrillation synchronization, so it cannot be connected to the
synchronization defibrillation instrument.
Magnetic and electrical fields are capable of interfering with the proper performance of
the device. For this reason make sure that all external devices operated in the vicinity of
the monitor comply with the relevant EMC requirements. Mobile phone, X-ray
equipment or MRI devices are a possible source of interference as they may emit higher
levels of electromagnetic radiation.
EXPLOSION HAZARD: Do not use this device in the presence of flammable anesthetics,
explosive substances, vapors or liquids.
7
WARNING
Keep the monitor dry, prevent it from water and humidity, and avoid strong collision.
Once subject to accidental wetting, immediately clean the water off using dishcloth.
ELECTRIC SHOCK: Do not open the monitor housing. All servicing and future
upgrades to this device must be carried out by personnel trained and authorized by our
company only.
Do not put the monitor in environments such as high temperature and high pressure, gas
fumigation or liquid immersion. Before clean or sterilize the monitor, cut off the general
power please.
At the end of its service life, the product described in this manual, as well as its
accessories, must be disposed of in compliance with the guidelines regulating the disposal
of such products. If you have any questions concerning disposal of the products, please
contact with us.
CONTRAINDICATIONS
None.
FUNCTION
The G3 Multi-Parameter Patient Monitor can be used to monitor the major parameters such as
electrocardiogram (ECG), body temperature (TEMP), impedance respiration (RESP), oxygen
saturation (SpO2), invasive blood pressure (IBP), noninvasive blood pressure (NIBP) and CO2
(EtCO2 and FiCO2). It integrates the parameter measurement, display and record export as a whole,
which forms a compact and portable monitor.
The monitor is capable of monitoring the following parameters:
Electrocardiogram (ECG): heart rate (HR), 7 (or 3) leads ECG waveforms and ST segment
analysis.
Noninvasive blood pressure (NIBP): systolic pressure (SYS), diastolic pressure (DIA) and
mean arterial pressure (MAP).
Body temperature (TEMP): temperature of channel 1 (T1), temperature of channel 2 (T2)
and temperature difference between the two channels (T).
Pulse oxygen saturation (SpO2): SpO2, pulse rate (PR) and SpO2 plethysmogram.
Respiration: respiration rate (RR) and respiration (impedance respiration or nasal tube
respiration) waveform.
Invasive blood pressure (IBP): 2 channels of IBP waveforms, systolic pressure (SYS),
diastolic pressure (DIA) and mean pressure (MEAN).
Carbon dioxide (CO2): end-tidal carbon dioxide (EtCO2), fractional inspiratory carbon
dioxide (FiCO2) and CO2 waveform.
8
CHAPTER 2:
INTRODUCTION
EXTERNAL APPEARANCE
G3C
G3C Front Panel
The front panel of the G3C Multi-Parameter Patient Monitor is shown as Figure 2-1:
(2)
(3)
(4)
(1) (5)
(6)
(7)
(8)
(12) (11) (10) (9)
Figure 2-1
(1) Display
Waveforms, menu, alarms and measuring parameters are displayed here.
(2) Silence key
Press this key to start or stop the monitor tones, including heart beat tones, pulse tones and
prompt tones for wrong operation.
Pressing this key consecutively will silence the system for 30 seconds, 60 seconds, 120 seconds
or until the next time the tones started. At this time, the silence status icon displayed in the
status bar changes from to with the time to start the monitor tones again displayed on the
right side, such as . When the time counts backwards to zero, or the silence key is pressed
when the monitor is silenced, the monitor tones will be started again.
(3) Alarm key
Press this key to enter Alarm menu. See CHAPTER 5: ALARMS for detailed information.
(4) Freeze key
This key is pressed to freeze and unfreeze the waveforms. See CHAPTER 6: WAVEFORM
FREEZING AND RECALLING for detailed information.
(5) NIBP key
Press this key to start or stop the non-invasive blood pressure measurement. See CHAPTER 15:
NIBP MONITORING for detailed information.
9
(6) Print key
Press this key to start or stop the waveforms and measured parameter values printing. See
CHAPTER 7: PRINTING for detailed information.
(7) Main menu key
Press this key to popup the Main menu or exit the menu currently displayed. See CHAPTER 4:
MENU for detailed information.
(8) Rotating mouse
Turn the rotating mouse in either direction to highlight labels and menu options. After
highlighting the desired selection, press the mouse to execute an operation, make a selection
and view a new menu or a dialog box. This procedure is referred to as select through out the
manual. Remember rotate to highlight, and then press to select.
(9) Brightness adjusting knob
Turn this knob to adjust the brightness of the monitor screen. Turn clockwise to brighter the
screen; turn counterclockwise to darker the screen.
(10) Volume adjusting knob
Turn this knob to adjust the volume of the monitor. Turn clockwise to higher the volume; turn
counterclockwise to lower the volume.
(11) Power indicator
ON: The monitor power is turned on.
OFF: The monitor power is turned off.
(12) Charge indicator
ON: AC power is applied to the monitor.
OFF: AC power is not applied to the monitor.
G3C Side Panel

The side panel of the G3C Multi-Parameter Patient Monitor is shown as Figure 2-2:
(1) (2)
(3) (4)
(5) (6)
(7) (8)
Figure 2-2
There are eight connectors on this panel:

(1) TEMP1 Temperature probe connector (channel 1).
(3) RESP Respiration pipe connector.
(4) NIBP NIBP cuff hose connector.
10
(5) IBP1 IBP transducer connector (channel 1).
(7) SpO2 SpO2 probe connector.
(8) ECG/RESP ECG cable connector.
Type CF applied part. The unit displaying this symbol contains an F-type
isolated (floating) patient part providing a high degree of protection
against shock.
Type BF applied part.
Attention: Consult accompanying documents (this manual).
G3C Rear Panel

The rear panel of the G3C Multi-Parameter Patient Monitor is shown as Figure 2-3:
(11)
(1)
(2)
(3)
(4)
(5) (6) (7) (8) (9) (10)
Figure 2-3
(1) Power switch
The key turns on or off the monitor.

(2) Speaker holes
(3) Dispersion holes
(4) AC power input connector
A three-wire power cord can be connected to this receptacle to provide AC power supply to the
patient monitor.
(5) Fuse socket
(6) Equipotential ground
When the monitor is used with other equipment, it can be connected to equal the potentials.
(7) Network connector: Standard RJ45 connector.
Through network connector, this monitor can be connected with the central monitoring system,
another monitor, or a PC. It enables the functions of other patient viewing, data output and
11
software upgrading.
(8) Printer connector
(9) VGA monitor connector

A standard colour VGA monitor can be connected to the patient monitor through this connector.
(10) Battery cover
(11) Handle
G3C Mechanics Plan
G3D
G3D Front Panel
The front panel of the G3D Multi-Parameter Patient Monitor is shown as Figure 2-4:
(20)
12
(2)
(3)
(4)
(1) (5)
(6)
(7)
(8)
(9)
(10) (11) (12) (13) (14) (15) (16) (17) (18) (19)
Figure 2-4
(1) Display
(2) Silence key
(3) Alarm key
(4) Freeze key
(5) NIBP key
(6) Print key
(7) Main menu key
13
(8) Rotating mouse
(9) Power switch
Press this key and hold for more than two seconds to turn on or off the monitor.
(10) TEMP1 Temperature probe connector (channel 1)
(12) NIBP NIBP cuff hose connector
(13) RESP Respiration pipe connector
(14) SpO2 SpO2 probe connector
(15) ECG/RESP ECG cable connector
(16) IBP1 IBP transducer connector (channel 1)
(18) POWER Power indicator
(19) CHARGE Charge indicator
(20) Alarm indicator
When a parameter value exceeds its alarm limit, this indicator flashes in red once a second.
against shock.
G3D Rear Panel

The rear panel of the G3D Multi-Parameter Patient Monitor is shown as Figure 2-5:
14
(9)
(1)
(2) (8)
(3)
(4) (5) (6) (7)
Figure 2-5

(4) Fuse socket
(6) Network connector: Standard RJ45 connector
software upgrading.
(7) Battery cover
patient monitor.
(9) Handle
15
G3F
G3F Front Panel
The front panel of the G3F Multi-Parameter Patient Monitor is shown as Figure 2-6:
(2)
(3)
(4)
(5)
(6)
(1)
(7)
(8)
(9)
(11) (10)
Figure 2-6
(1) Display
16
(2) Alarm indicator
(3) Silence key
(4) Alarm key
(5) Freeze key
(6) NIBP key
(7) Print key
(8) Rotating mouse
(9) Main menu key
G3F Side Panel

The side panel of the G3F Multi-Parameter Patient Monitor is shown as Figure 2-7:
17
(1) (2)
(3)
(4)
(5)
(6)
Figure 2-7
There are six connectors on this panel:

(1) T1 Temperature probe connector (channel 1)
(2) T2 Temperature probe connector (channel 2)
against shock.
G3F Rear Panel

The rear panel of the G3F Multi-Parameter Patient Monitor is shown as Figure 2-8:
(1)
(2)
(3)
(4)
(9)
(5) (6) (7) (8)
18
Figure 2-8
(2) Power switch

patient monitor.
(4) Fuse socket
another monitor, or a PC. It enables the functions of other patient viewing, data output and on-
line software upgrading.
(9) Speaker holes
19
G3G
G3G Front Panel
The front panel of the G3G Multi-Parameter Patient Monitor is shown as Figure 2-9:
(2)
(3)
(4)
(5)
(6)
(1) (7)
(8)
(9)
(10)
(11)
Figure 2-9
20
(1) Display
(2) Alarm indicator
(3) Power indicator
(5) Silence key
(6) Alarm key
(7) Freeze key
(8) NIBP key
(9) Print key
(10) Main menu key
Press this key to popup the Main menu or exit the menu currently displayed. See CHAPTER
4: MENU for detailed information.
(11) Rotating mouse
G3G Side Panel

The side panel of the G3G Multi-Parameter Patient Monitor is shown as Figure 2-10:
21
(1) (5)
(2) (6)
(3) (7)
(4) (8)
Figure 2-10

against shock.

G3G Rear Panel
The rear panel of the G3G Multi-Parameter Patient Monitor is shown as Figure 2-11:
22
(12)
(1)
(11)
(10)
(2)
(9)
(3) (4) (5) (6) (7) (8)
Figure 2-11
(2) Power switch
(4) Printer connector

software upgrading.
patient monitor.
(10) Fuze socket
(11) Speaker holes
23
(12) Handle
G3H Part
FRONT PANEL
The front panel of the G3H Multi-Parameter Patient Monitor is shown as Figure 2-1:
(1)
(2)
(3) (4) (5) (6) (7) (8) (9) (10) (11)
Figure 2-1
(13) Alarm Indicator

(14) Display
(15) Silence key
24
(16) Alarm key
(17) Freeze key
(19) Rotating mouse
(21) NIBP key
(22) Print key
(23) Main menu key
SIDE PANEL
The left side panel of the G3H Multi-Parameter Patient Monitor is shown as Figure 2-2:
25
(1)
(2) (8)
(3)
(4) (9)
(5)
(6) (10)
(7)
Figure 2-2

(1) Handle.
(2) NIBP NIBP cuff hose connector.
(5) SpO2 SpO2 probe connector.
(6) RESP Respiration pipe connector.
(7) Battery cover.
(10)ECG/RESP ECG cable connector.
against shock.
The right side panel of the G3H Multi-Parameter Patient Monitor is shown as Figure 2-3:
26
(7)
(1)
(2) (6)
(3) (4) (5)
Figure 2-3

(9) Printer.
patient monitor.
(11) Fuse socket
(14) Network connector: Standard RJ45 connector.
software upgrading.
(15) Handle.
REAR PANEL
The rear panel of the G3H Multi-Parameter Patient Monitor is shown as Figure 2-4:
27
(1) (3)
(2)
Figure 2-4
(12) Handle.
(13) Battery cover.
(14) Power switch.
Mechanics Plan
28
DISPLAY
The display of this monitor is divided into four major areas, such as channels area, parameters area,
status bar and menu bar. The status bar is on the top part of the screen, the channels area is under the
status bar, on the left part of the screen, while the menu bar is at the lower part of the screen. The
parameters are always displayed on the right part of the screen. The menu pops up and shuts out part
of the channels area and parameters area. The standard display interface is as the following:
(4)
29
(3)
(1)
(2)
The monitor provides a channels area configuration function to configurate the channels area.
Through channels setting, the monitor displays an interface as below, where the parameters are
displayed on the right and lower parts. See DISPLAY in CHAPTER 4 for more information about
channels setting.
(3)
(1) Channels area

The channels area is divided into several channels, and can be selected from the ECG waveform,
RESP waveform, PLETH waveform, IBP waveform, CO2 waveform, trend graph and trend table. The
label of the channel is usually displayed on the upper left corner of the channel. Selecting the label
will enter the corresponding menu. What is displayed at the same row of the label is the status
information concerning this channel.
(2) Menu bar
The menu bar automatically pops up and disappears. Pressing the Main menu key, Alarm key, Freeze
30
key or the parameter/channel labels can activate the corresponding menu to display.
(3) Parameters area
The heart rate (HR), pulse oxygen saturation (SpO 2), respiration rate (RR), body temperature
(T1/T2), non-invasive blood pressure (NIBP), invasive blood pressure (IBP), end-tidal carbon
dioxide (EtCO2) and fractional inspiratory carbon dioxide (FiCO2) are displayed in this area. Every
parameter has a corresponding label with an alarm prohibition icon on the left side. Selecting the
label will enter the corresponding menu.
(4) Status bar
Displays the monitor status information and patients information.

1 Patient name: It can be set in the Patient Information dialog box. If the patient isnt named, it
displays No named patient. See PATIENT in CHAPTER 4 for setting method.
2 Patient type: ADULT, PEDIATRIC or NEONATE. See PATIENT in CHAPTER 4 for setting
method.
3 System date. The system date and its display format can be set. See SET TIME and REGION
SETTINGS in CHAPTER 4 for setting method.
4 System time. It can be set. See SET TIME in CHAPTER 4 for setting method.
5 The alarm status icon
Physiological alarms enabled
Physiological alarms disabled.
6 The battery symbol: Denotes the capacity in the battery. See BATTERIES in CHAPTER 2 for
more information.
7 Status icon of the central monitoring system network
Red icon The monitor is disconnected from the central monitoring system.
Blue icon The monitor is connected to the central monitoring system.
8 The silence status icon
System not silenced
System silenced.
WARNING
The system doesnt generate physiological alarms if the icon shows.
BATTERIES
This monitor designed to operate on baterry power during intra-hosipital patient transfer or
whenever the power supply is interrupted. The battery is charged automatically when the monitor is
connected to AC power, no matter the monitor is powered on or not.
The battery symbol displayed on the main screen tells the status of the battery.
31
( or ) The battery is installed in the battery slot.The
grid part indicates its capacity.
(red and flashing) No battery is installed in the battery slot or
the electrical volume is to be exhausted.
Besides, the charge indicator also indicates the status of the battery.
ON The battery is being charged or the battery is fully
charged.
OFF No battery is installed or the battery is installed but the monitor is not connected
to AC power.
The capacity of the battery is limited. When the battery capacity is too low, a flashing red symbol
shows in the status bar. At this moment, the AC power shall be applied to the monitor.
NOTE
Take out the battery before the monitor is transported or will not be used for a long time.
WARNING
Keep the battery out of the reach of children.
Only use the battery specified by the manufacturer.
BATTERY MAINTENANCE
Conditioning a Battery
A battery should be conditioned before it is used for the first time. A battery conditioning cycle is
one uninterrupted discharge of the battery. Batteries should be conditioned regularly to maintain
their useful life. Condition a battery once when it is used or stored for two months, or when its run
time becomes noticeably shorter.
To condition a battery, follow this procedure:
1. Disconnect the monitor from the patient and stop all monitoring or measuring.
2. Insert the battery in need of conditioning in the battery slot of the monitor.
3. Apply AC power to the monitor and allow the battery to charge uninterrupted for 10 hours.
4. Remove AC power and allow the monitor to run from the battery until it shuts off.
5. Apply AC power again to the monitor and allow the battery to charge uninterrupted for 10
hours.
6. This battery is now conditioned and the monitor can be returned to work.
Checking a Battery
The performance of a rechargeable battery may deteriorate over time. To check the performance of a
battery, follow this procedure:
1. Disconnect the monitor from the patient and stop all monitoring or measuring.
2. Apply AC power to the monitor and allow the battery to charge
uninterrupted for 10 hours.
32
3. Remove AC power and allow the monitor to run from the battery until it
shuts off.
4. The operating time of battery reflects its performance directly.
Please replace the battery or contact with the maintenance personnel if its
operating time is significantly lower than the specified time.
NOTE
Life expectancy of a battery depends on how frequent and how long it is used. For a
properly maintained and stored lead-acid or lithium ion battery, its life expectancy is
about 2 or 3 years respectively. For more aggressive use models, life expectancy can be
less. We recommend replacing lead acid batteries every 2 years and lithium ion batteries
every 3 years.
The battery might be damaged or malfunctioned if its operating time is too short after
being fully charged. The operating time depends on the configuration and operation. For
example, measuring NIBP more frequently will also shorten the operating time.
BATTERY RECYCLING
When a battery has visual signs of damage, or no longer holds a charge, it
should be replaced. Remove the old battery from the monitor and recycle it
properly. To dispose of the batteries, follow local laws for proper disposal.
WARNING
Do not disassemble batteries, or dispose of them in fire, or cause them to short circuit.
They may ignite, explode, leak or heat up, causing personal injury.
33
CHAPTER 3:
INSTALLATION
WARNING
The installation of the monitor must be carried out by personnel authorized by us. The
software copyright of the monitor is solely owned by our company. Any action to change,
copy or exchange the software copyright by any organization or person is regarded as
copyright infringement and is not allowed.
If the monitor is connected to another electrical instrument and the instrument
specifications cannot tell whether the instrument combination is hazardous (e.g. due to
summation of leakage currents), you should consult us or experts in the field to ensure the
required safety of all instruments concerned.
NOTE
The operations in this section are not all required. User-customized installation by
authorized personnel is provided.
UNPACKING AND CHECKING

Please open the package according to the positions marked on the packing case, and take out the
monitor and accessories carefully.
Check the accessories against the packing list.
Check the monitor and accessories for any mechanical damage.
Contact the distributor immediately in case of any problem.
Friendly remind: Please save the packing case and packaging material for further transport
and storage.
WARNING
Be sure to keep the packaging materials from childrens reach.
Disposal of the packaging materials shall comply with your local requirements.
The equipment might be contaminated in storage, transport or when used. Verify the
package and the single use accessories are intact. In case of any damage, do not apply it to
patients.
34
ENVIRONMENTAL REQUIREMENTS
The operating environment of the monitor must meet the requirements specified in
ENVIRONMENTAL SPECIFICATIONS in APPENDIX A.
The environment where this monitor is to be used should be free from noise, vibration, dust, and
corrosive or explosive and inflammable substances. Do not place the monitor against the wall, and
do not plug up the dispersion holes on the back and two sides of the monitor for proper air
circulation.
Condensation can form when the monitor is moved from one location to another, and being exposed
to differences in humidity or temperature. Make sure that during operation the instrument is free
from condensation.
INSTALLATION METHOD
CONNECTING TO AC POWER SUPPLY

1. Use the original three-wire AC power cord.
2. Connect the power cord to the receptacle for AC power cord on the rear
panel of the monitor.
3. Connect the other end of the power cord to a compatible 3-prong hospital
grade AC power outlet.
The 3-prong power outlet must be grounded. If it is doubted, contact related
personnel of the hospital.
WARNING
Confirm the AC power supply is in conformity with the requirements of this equipment:
(100240)V a.c., 50/60Hz.
Do not use three-wire to two-wire adapter with this instrument.
To avoid unexpected power interruption, do no use power outlet with a wall-mounted
switch control.
INSTALLING THE BATTERY

If the monitor is to be powered by the internal battery, install the battery
following the steps as below:
1. Slide the battery door in the indicated direction (G3C/G3D), or screw off
the screws and open the rear panel.
2. Insert the battery into the battery slot per the + and - indications.
3. Fix the battery with screws (for G3D, cover it with the plate first).
4. Close the battery door (G3C/G3D), or fix the rear panel with screws
(G3F/G3G).
WARNING
35
Make sure the monitor has been disconnected with AC power supply before battery
installation.
Make sure the battery door or the rear panel is securely latched. Falling batteries could
seriously or fatally injure a patient.
EQUIPOTENTIAL GROUNDING
When other equipments are used together with the monitor, the grounding
cable should be used to connect the equipotential ground of the monitor and of
other equipments. This helps to reduce the potential differences between
different pieces of equipment, and ensure the safety of the operator and
patient.
WARNING
If the grounding system is in doubt, the monitor must be supplied from its internal
battery.
Accessory equipments connected to this patient monitor must be certified according to the
respective IEC standards (e.g. IEC 60950 for information technology equipment and IEC
60601-1 for medical electrical equipment). Furthermore all configurations shall comply
with the valid version of the system standard IEC 60601-1-1. Any person who connects
additional equipment to the signal input or signal output is responsible to ensure the
system complies with the requirements of the valid version of the system standard IEC
60601-1-1. If in doubt, contact our company or customer service.
CONNECTING PATIENT SENSORS AND PROBES

Connect the necessary patient sensors or probes to the monitor. For details, see
the chapters for specific parameter monitoring in the following pages, or
corresponding instructions for sensors and probes.
CONNECTING THE NETWORK CABLE

The network connector of the monitor is a standard RJ45 connector. It connects
the monitor with the central monitoring system, or with a PC for upgrading or
data output. It can also connect with another patient monitor for other patient
viewing.
1. Connect one end of the network cable with the network connector of the monitor.
2. Connect the other end of the network cable with the hub or switch of the central monitoring
system, or with the network connector of a PC, or with the network connector of another
patient monitor.
WARNING
Different network cable may be used for different connections. Please consult our
customer service personnel for details.
The system upgrading through the network connector is to be executed by our authorized
36
personnel only.
CONNECTING TO VGA MONITOR

This monitor can be connected with a standard color VGA monitor. The VGA
monitor will display the patient waveforms and parameters measured by the
patient monitor. To connect the patient monitor with the VGA monitor, follow the
steps as below.
1. Install the VGA monitor at a distance of more than 1.5 meters from the patient.
2. Power off the patient monitor.
3. Connect the signal cable of the VGA monitor to the VGA connector on the rear panel of the
patient monitor.
4. Power on the VGA monitor and then the patient monitor.
REPLACE THE FUSE

1. Pull out the fuse socket (G3C/G3D/G3F), or screw off the fuse socket (G3G).
2. Push up the fuse and replace it with a new one.
3. Push the fuse socket back (G3C/G3D/G3F), or screw back the fuse socket (G3G).
POWERING ON THE MONITOR

After installing the monitor, please follow the procedures described below to
power on the monitor:
1. Before using the monitor, please carry out corresponding safety inspection
as given in INSPECTION in CHAPTER 20.
2. Press the Power switch and the Power indicator is lighted on.
3. The boot-strap picture and pace-bar are displayed on the screen.
4. When the pace-bar reaches 100%, the system displays the main screen.
5. At this time, you can operate the monitor using the keys and rotating
mouse.
POWERING OFF THE MONITOR

To power off the monitor, please follow the procedures below:
1. Confirm the patient monitoring is to be finished.
2. Disconnect the cables and sensors between the monitor and the patient.
3. Press the Power switch, and the monitor will be powered off.
37
CHAPTER 4:
MENU
MENU OPERATION
The basic format of menu is as the following (Main menu):
POPUP MENU
The monitor has four methods to popup the menu:
Press the Main menu key on the front panel to popup the Main menu.
Press the Alarm key on the front panel to popup the Alarm menu.
Press the Freeze key on the front panel to popup the Freeze menu.
Select a parameter/channel label to popup the corresponding menu.
BROWSE MENU
The inverse black button in the menu bar is the button selected by the cursor. Select the desired
button to popup the corresponding submenu or dialog, or carry out the selected function. Please refer
to the relevant part in this manual for detailed information.
EXIT MENU
The monitor has three methods to exit from the menu:
Select the Exit button in the right-end of menu bar to return to the previous menu.
When a menu is displayed, press the Main menu key on the front panel to exit the menu.
No operation for more than one minute, the monitor automatically exits the menu.
DISPLAY
Pressing the Main menu key on the front panel pops up the following Main menu:
38
Display: Sets the display interface.
Tools: Sets the practical tools.
Review: Checks/reviews the history trend or data.
Patient: Sets the patients information.
System Setup: Sets the system information.
Recorder Setup: Sets the recorder/ built-in printer parameters.
Selecting Display in the Main menu pops up the following Display menu.
FIXED FORMAT
Selecting Fixed Format in the Display menu pops up the following menu.
In this Fixed Format menu, the user can select display format from five existed formats. Select a
button, the main interface will display accordingly.
1 ECG: One ECG (main lead) waveform is displayed in the channels area.
2 ECGs: Two ECG (main lead and another lead) waveforms are displayed in the channels area.
3 ECGs: Three ECG wavforms, a PLETH wavform and a RESP waveform are displayed in the
channels area. It is the default display fomat.
39
7 ECGs: Seven ECG (IIIIIIaVRaVLaVF and V leads) waveforms are displayed in the
channels area.
Huge Digit: HR and SpO2 are displayed in huge digit, while the main lead ECG waveform is
displayed on the top part of the screen.
USER FORMAT
Selecting User Format in the Display menu pops up the following menu.
In this User Format menu, the display format of main interface can be set as the user format. The
system supports 5 user formats. The current display format can be saved as a user format via Format
Setup button. See the following FORMAT SETUP for detailed information.
40
FORMAT SETUP
Selecting Format Setup in the Display menu pops up the following dialog box.
The Setup Display Channel dialog box displays the label of channel that is displayed in the channels
area currently.
Save as: Not Save or User Format 1~5 could be selected. If Not Save is selected, the channels
area displays the channels selected in this dialog box. If User Format 1~5 is selected, not only the
channels area displays the channels selected in this dialog box, the current display format will be
saved as a user format also.
Select a desired channel, the Select Channel menu as figure above pops up. All channels are listed in
this menu. Select the desired channel label to add it into the Setup Display Channel dialog box.
NOTE
Cannot display the same channel.
If channel is Blank, it means no channel to be displayed at this position.
If select the ECG channel, the system will match the relevant ECG lead automatically.
OXYCRG
Select oxyCRG in the Display menu, the following oxyCRG graph will be displayed in the channels
area.
The oxyCRG is formed by HR, SpO2 and RESP trend graphs. On the right side of the RESP label, its
relevant information is displayed, and at the bottom of the RESP trend graph, the time scale is
displayed, such as 1min, 2min, 3min or 4min. OxyCRG only shows the trend graph for the last 3 or
4 minutes.
41
ALARM LIMIT
Select Alarm Limit in the Display menu to display or hide the alarm limit in parameters area, shown
as below.
Alarm limit
WAVEFORM SPEED
Select Waveform Speed in the Display menu, the following Waveform Speed Setting dialog box
pops up, where the waveform speed of the ECG/PLETH/IBP and RESP/CO2 can be adjusted.
Options: 6.25mm/s, 12.5mm/s, 25mm/s and 50mm/s. The default waveform speed is 25mm/s.
OTHER SETTINGS
Selecting Other Settings in the Display menu pops up the following menu:
NIBP Size
Select NIBP Size in the Other Settings menu, the NIBP value display format switches among three
formats, shown as below.
or or
IBP1 Size
Select IBP1 Size in the Other Settings menu, the display format of channel 1 IBP value switches
among three formats, shown as below.
or or
IBP2 Size
Select IBP2 Size in the Other Settings menu, the display format of channel 2 IBP value switches
among three formats, shown as below.
42
or or
IBP Overlap
Select IBP Overlap in the Other Settings menu, the IBP waveforms of two channels are displayed in
a channel, shown as below.
Menu Font
Select Menu Font in the Other Settings menu, the menu font switches between large font and small
font, shown as below.
Screen Font
Select Screen Font in the Other Settings menu, the screen font switches between large font and small
font, shown as below.
Pleth Fill
Select Pleth Fill in the Other Settings menu, the PLETH waveform will be filled or be blank, shown
as below.
CO2 Fill
Select CO2 Fill in the Other Settings menu, the CO 2 waveform will be filled or be blank, shown as
below.
TOOLS
Selecting Tools in the Main menu pops up the following menu:
Event: Sets the event. See CHAPTER 9: EVENTS for detailed information.
43
Drug Calculator: Calls the drug calculator. See CHAPTER 10: DRUG CALCULATOR for
detailed information.
Other Patient: Views waveforms and parameter values of another monitor in the same LAN.
See CHAPTER 11: OTHER PATIENT VIEWING for detailed information.
Standby: Enters standby mode. In this mode, the monitor shows standby interface instead of the
main interface and gives the audible alarms if an alarm occurs. Press the Main menu key on the
front panel to return to the normal mode.
REVIEW
Selecting Review in the Main menu pops up the following menu.
Trend: Reviews/checks the trend data. See CHAPTER 8: TRENDS for detailed information.
Recall: Recalls the saved waveform. See CHAPTER 6: WAVEFORM FREEZING AND
RECALLING for detailed information.
PATIENT
Select Patient in the Main menu, and the following Patient information dialog box pops up.
No: Patient identification number, set via soft keyboard.

Name: Patient name, set via soft keyboard. If no name is set, it shows No named patient.
Sex: Patient gender. Male or Female, while Male is the default.
Age: Patient age. The default age is 25. Rotating the mouse clockwise increases the age, while
counterclockwise decreases the age.
Patient type: ADULT, PEDIATRIC or NEONATE, while ADULT is the default.
Soft Keyboard
Select the input field on the right side of No as the figure above, the soft keyboard pops up, shown as
below.
Consecutively select this button, the Characters field shows the capital, lowercase,
numeral and punctuation in sequence.
Pages down or pages up the characters in the Characters field.
Characters field: Press and turn the rotating mouse to select the desired character,
then press the mouse again to add it into the input field.
44
Moves the cursor in the Characters field. Select this button then turn the rotating mouse
to move the cursor forward or backward.
Deletes the character before the cursor.
Confirms the input.
SYSTEM SETUP
Seleting System Setup in the Main menu pops up the following menu.
In this menu, Calibration is used by the manufacturer, while the others are used by the user.
SET TIME
Selecting Set Time in the System Setup menu pops up the Set Date dialog box, shown as below.
The Year, Month, Day, Hour, Minute and Second of the system time can be set in this dialog box.
NOTE
Reseting the system time will clear the stored trend data.
REGION SETTINGS
Selecting Region Settings in the System Setup menu pops up the following menu.
Select Units
Selecting Select Units in the Region Settings menu pops up the Parameter Unit dialog box, shown as
below.
The pressure unit and temperature unit can be set in this dialog box. The options of pressure unit:
kPa and mmHg. The options of temperature unit: Cent and Frnt. Click Ok to confirm the selection,
and the corresponding value will be displayed with the selected unit.
45
Date Format
Selecting Date Format in the Region Settings menu pops up the Set Date Format dialog box to set
the date format, shown as below.
Power Frequency
Selecting Power Frequency in the Region Settings menu pops up the Set Power Frequency dialog
box, shown as below.
The power frequency can be set as 50Hz or 60Hz.
NOTE
Please set the proper power frequency, or the ECG signal noise will be loud.
Language
Select Laguage in the Region Settings menu, and the system language changes.
NETWORK SETTINGS
Selecting Network Settings in the System Setup menu pops up the following menu.
IP Address
Selecting IP Address in the Network Settings menu pops up the Network setting dialog box to set the
IP address, shown as below.
If Use dynamic IP configuration (DHCP) is selected, the monitor is distributed an IP address

automatically when it is turned on to prevent from the IP address conflict.
46
Set the IP address manually: Remove the selection of Use dynamic IP configuration (DHCP), and
then select the input field on the right side of IP address to set it manually. Select Ok button to
confirm the selection, the monitor IP address will not change.
Server
Selecting Server in the Network Settings menu pops up the Server Setup dialog box where the
address of the central monitoring system server can be set, shown as below.
Auto: The monitor searches the address of the server automatically.

IP address: Input the IP address of the server manually.
Domain Name: Input the domain name of the server via soft keyboard, such as
http://szmedtech.com.
Device Name
Selecting Device Name in the Network Settings menu pops up the Edit Device Name dialog box,
shown as below.
The device name of the monitor can be set in this dialog box. If the monitor is not named, it shows
No Name.
MAINTENANCE
Selecting Maintenance in the System Setup menu pops up the following menu.
Reserved 1 and Reserved 2 are the manufacturer maintenance buttons, which the user dosent need
to use.
System Status
Selecting System Status in the Maintenance menu pops up the following menu to view and check the
relevant information of the system.
Main Settings
Selecting Main Settings in the System Status menu pops up the following Settings List information
box where all the parameters and patient setting information can be viewed and checked.
47
Alarm Limits
Selecting Alarm Limits in the System Status menu pops up the following Alarm Settings information
box where the upper alarm limits, lower alarm limits and alarm switches of all the parameters can be
viewed and checked.
Software Version
Selecting Software Version in the System Status menu pops up the following Software Information
box.
In this information box, the Serial NO., GBA440 (ARM) board software version, GAA718 board
software version, KERNEL software version, GBA440 start time and Oximeter board software
version can be checked.
48
Remote Maintenance
WARNING
The remote maintenance must be carried out by personnel trained and authorized by our
company only.
This button is used for software upgrade.

New software version to improve the performance or add new function is subject to issued without
prior notice. If you need to upgrade the software, please follow the procedure specified below.
1. Install the software upgrading program Monitor Maintenance.
2. Connect the network connectors of the monitor and of the PC with TIA/EIA568B network
cable.
3. Power on the monitor, press Remote Maintenance button in the Maintenance menu and hold for
5 seconds, the Remote Maintenance Service interface appears, shown as below.
DHCP: Select this button, the server distributes an IP address to the monitor automatically.
Set NET: Select this button to set the IP address manually.
Connect Server: Select this button to connect the monitor to the server. If connect
successfully, the lower left part of the interface shows a green field with word Connected
on it, while unsuccessfully, shows a red field with word Connecting on it.
Return MonitorSelect this button to return to the monitoring mode.
Disconnect: Select this button to disconnect the monitor with the server, and the lower left
part of the interface shows a yellow field with word Disconnect on it.
CONNECT INFORMATION area at the lower right part of the interface displays the operation
information, where you can check whether an operation is successful.
4. Run Monitor Maintenance program, and follow the procedure specified in the Software
Upgrade Manual to upgrade.
5. After finishing the upgrade, exit the Monitor Maintenance program and select the Return
Monitor button to return to the monitoring mode.
Please contact the Customer Service Department for the Monitor Maintenance program (with
Software Upgrade Manual).
49
Demo
Select DEMO in the Maintenance menu, the system enters the demonstration mode. In this mode,
the monitor simulates the wavforms and parameters in real use, and displays word DEMO on the
screen. The purpose of the demonstration mode is to demonstrate the
performance of the monitor, and for training purposes.
WARNING
In clinical applications, this function is forbidden because the DEMO status can mislead
the medical staff to treat the DEMO waveforms and parameters as the actual data of the
patient. This may result in serious injury to the patient, or a delay of treatment or
improper treatment.
DEFAULT SETTINGS
Selecting Default Settings in the System Setup menu pops up the Set Default Settings dialog box,
shown as below.
Select Ok, the system reverts to the default settings.
RECORDER SETUP
Selecting Recorder Setup in the Main menu pops up the Set Printer Parameters dialog box, shown as
below.
Curve Mode: Printing mode of the curve.

Mode 1: Print an electrocardiogram waveform, namely the main lead ECG waveform.
Mode 2: Print two waveforms, namely the main lead ECG and PLETH waveforms.
Curve Speed: Printing speed. Options: 12.5mm/s and 25mm/s.
50
Total (Seconds): Waveform printing time. It can be selected in the range from 5 to 30 seconds.
Alarm Print: Alarm printing switch.
Open: The printer automatically prints all the measured parameter values when the
physiological alarms occur.
Close: The printer doesnt print any measured parameter value when the physiological alarms
occur.
Timer Print: Timer printing switch.
Open: The printer automatically prints all the measured parameter values at the preset interval.
Close: The printer dosent print any measured parameter value automatically.
Interval: The interval time between two printings, which can be selected in the range from 1 to
60 minutes.
The default settings for the Alarm Print and Timer Print both are Close.
Refer to CHAPTER 7: PRINTING for detailed information.
CHAPTER 5:
ALARMS
The monitor gives audible or visual alarms to indicate the medical staff, when a
vital sign of the patient appears abnormal, or mechanical or electrical problems
occur to the monitor.
ALARM CATEGORIES
The alarms are divided into two categories:
Physiological alarms
A physiological alarm either indicates that a monitored physiological parameter
is out of specified limit or indicates an abnormal patient condition.
Prompt information
Besides the physiological alarm, the monitor also displays the information related to the system. For
example, if a parameter module is turned on but the required leads or sensor
are not connected, the monitor will prompt accordingly, such as Lead Off in
the ECG and RESP channels, Sensor Off in the PLETH channel, or No Cuff
under the NIBP parameter, etc. Prompt information is usually displayed in the
channels area. But the prompt information relating to NIBP is displayed under
51
the NIBP value in the parameters area.
ALARM MODES
When an alarm occurs, the monitor raises the users attention by the following
audible or visual indications.
Visual alarms
When a measured physiological parameter value exceeds the preset alarm limit, the alarm
indicator on the front panel flashes in red once a second.
Audible alarms
When a measured physiological parameter value exceeds the preset alarm limit, the
monitor phonates a triple-beep tone each three seconds to prompt users.
Character flashes
When a measured physiological parameter value exceeds the preset alarm limit, or a lead
or sensor is disconnected to the monitor, this parameter value in parameters area or the prompt
information in the corresponding channel flashes once a second.
ALARM SETTINGS
SETTING ALARM VIA ALARM KEY
Press the Alarm key on the front panel of the monitor, the following Alarm menu pops up:
Alarm On/Off
Enables or disables the physiological alarms.
Alarms enabled: Icon is displayed in the status bar, the physiological alarms are turned on, and
the monitor alarms when a measured paratmeter value exceeds the preset alarm limit.
Alarms disabled: Icon is displayed in the status bar, the physiological alarms are turned off,
and the monitor does not generate alarms even if the measured parameter
value exceeds the preset alarm limit.
Alarm Settings
Select Alarm Settings in the Alarm menu, the following Set Alarm Limits dialog box pops up:
The upper alarm limit, lower alarm limit, alarm switch and alarm printing switch of each pararmeter
in different patient type can be set in this dialog box.
Patient Type: ADULT, PEDIATRIC or NEONATE.
52
Params: HR, SpO2, NIBP, RESP, TEMP, ST, IBP1, IBP2, FiCO2 or EtCO2.
High: Upper alarm limit.
Low: Lower alarm limit.
The input field on the right side of the lower alarm limit: Enables or disables the alarm of this
parameter and doesnt affect the alarms of other parameters.
On: The alarm of this parameter is turned on, and the monitor alarms when this measured
parameter value exceeds its preset alarm limit.
Off: Icon is displayed on the left side of this parameter label, the alarm of this parameter
is turned off, and the monitor does not generate alarms when the measuared value
of this parameter exceeds its preset alarm limit.
Print: Enables or disables the alarm printing of this parameter.
On: The alarm printing of this parameter is turned on, and the printer prints all the measured
parameter values automatically when this parameter alarm occurs.
Off: The alarm printing of this parameter is turned off, and the printer dosent print any
measured parameter values when this parameter alarm occurs.
Alarm Tone
Select Alarm Tone in the Alarm menu, the following Set Pulse & Alarm Tone dialog box pops up.
The pulse tone and alarm tone can be set separately in this dialog box. Input the tone value and
select Test, the monitor will phonate the corresponding test tone. Select Ok to confirm the setting.
Default Limit
Select Default Limit in the Alarm menu, the following Set Alarm Default Settings dialog box pops
up:
Selecting Ok in this dialog box sets all the alarm limits as their default values and enables the alarm
of each parameter, but doesnt change the status of the physiological alarms.
SETTING ALARM VIA PARAMETER LABEL

Selecting a parameter label pops up the corresponding menu. Although the menu of each parameter
is different, all the menus have the same Alarm On/Off and Alarm Settings buttons to set the alarm
limits separately.
For example, select the HR label in the parameters area to pop up the HR menu, shown as below.
Alarm On/Off: Enables or disables the HR alarm.

Alarm enabled: The HR alarm is turned on and the monitor alarms when the measured HR
value exceeds its preset alarm limit.
Alarm disabled: Icon (red) is displayed on the left side of the HR label. The HR alarm is
53
turned off, and the monitor does not generate alarms when the measured HR value
exceeds its preset alarm limit.
Alarm Setting: Select this button, the following Set Alarm Limits dialog box pops up:
The Patient Type and Params cannot be changed in this dialog box.
High: Upper alarm limit. Determines the upper HR alarm limit.
Low: Lower alarm limit. Determines the lower HR alarm limit.
The input field on the right side of the lower alarm limit: Enables or disables the HR
alarm.
On: The HR alarm is turned on, and the monitor alarms when the measured HR value
Off: Icon is displayed on the left side of HR label, the HR alarm is turned off, and
the monitor does not generate alarms when the measured HR value
Print: Enables or disables the HR alarm printing.
On: The HR alarm printing is turned on, and the printer prints all the measured parameter
values automatically when a HR alarm occurs.
Off: The HR alarm printing is turned off, and the printer dosent print the measured
parameter values when a HR alarm occurs.
The functions of other buttons in the HR menu are specified in CHAPTER 12: ECG
MONITORING.
WHEN AN ALARM OCCURS
WARNING
When an alarm occurs, always check the patients condition first.
When an alarm occurs to the monitor, refer to the following steps and take action
properly.
1. Check the patients condition.
2. Identify the alarming parameter and the alarm category.
3. Identify the cause of the alarm.
4. Take action to remedy the alarm cause.
5. Check if the alarm is cleared.
54
Chapter 6:
WAVEFORM FREEZING AND RECALLING
OVERVIEW
You can freeze the monitored waveforms of a patient as desired and view the
waveforms of 15 seconds to gain a clear observation.
The freezing and recalling function of the monitor have the following features.
When the monitor enters the frozen mode, it exits all other menus
automatically.
The system freezes all waveforms displayed in the channels area.
At most, the frozen waveforms saved in the last 8 times can be recalled.
FREEZING AND UNFREEZING
WAVEFORM FREEZING
Press the Freeze key on the front panel, all the waveforms displayed on the screen are frozen,
the system exits all displayed menus (if displayed), and the following menu pops up.
55
Last Page, Next Page: Turns the waveforms forward or backward to view the
waveforms of 15 seconds before freezing.
Save: Select this button to save the frozen waveforms. If the waveforms are
successfully saved, the following menu appears.
WAVEFORM UNFREEZING
To exit the frozen mode,
Select Exit in the Freeze menu
Press the Freeze or Main menu key on the front panel.
After exiting the frozen mode, all waveforms on the screen are cleared and new
real-time waveforms are displayed.
WAVEFORM RECALLING
Enter the Recall menu via the Review button, the waveforms saved at the last time and the following
menu are displayed on the screen.
Select File: Select this button, the following Please select files dialog box pops up:
The start time of the selected file;

The selectable saved files.
Move the cursor to position and select the desired file by turning the rotating mouse, then
select Ok, the corresponding waveforms will be displayed on the screen.
Last Page, Next Page: Turn the waveforms forward or backward to view the waveforms of
15 seconds before freezing.
Select Exit in the Recall menu or press the Main menu key on the front panel to exit the recalling
mode.
56
CHAPTER 7:
PRINTING
OVERVIEW
The printer is an optional constitution for this monitor. If the monitor equipped with a printer, there
is a Recorder Setup button in the Main menu for setting printer parameters.
The performance of the printer is described as below.
Prints patient information and parameters.
Prints a maximum of two waveforms.
The optional printing rates: 25mm/s and 50mm/s.
Multiple printing types are supported.
For details about the printer setup, please refer to RECORDER SETUP in CHAPTER
4.
PRINTING TYPES
The monitor supports the following types of printings:
Real-time printing.
Timer printing.
Alarm printing.
57
Trend graph printing (refer to TREND GRAPH WINDOW in CHAPTER 8).
REAL-TIME PRINTING
Press the Print key on the front panel, the real-time printing starts and the
current waveforms are printed until the preset printing time is over or the Print
key is pressed again, and then the measured parameter values at this moment
are printed. As described in RECORDER SETUP in CHAPTER 4, you can set the
Curve Mode, Curve Speed and Total in the Set Printer Parameters dialog box.
TIMER PRINTING
The monitor starts printing all the measured parameter values at the preset
interval.
ALARM PRINTING
The monitor starts printing all the measured parameter values when the monitor
generates physiological alarms.
NOTE
To realize the alarm printing of a parameter, the Alarm Print in Set Printer Parameters
dialog box, physiological alarms, and alarm and alarm printing of this parameter should
be enabled.
In working status, the printer cannot be configured.
If the interval arrives but the printer is in work, the monitor will give up the parameter
printing this time.
WAVEFORM AND PARAMETER PRINTING

Press the Print key on the front panel, the printer prints waveforms until the preset printing time is
over, then prints all the parameter values measured at this moment, and then stops.
Press the Print key to stop the current printing.
INSTALLING PRINTER PAPER

The printer used for this monitor is a special thermal printer that is installed on the side panel of the
monitor in embedded mode, shown as the following.
Error indicator
58
Power indicator
Latch Error Power
If the printer is properly installed, only the Power indicator lights on. If the Error indicator lights on,
it indicates that the printer is in paper lack status or the paper has not been installed properly. Do not
print at this time, or it will damage the printer. Follow the procedure below to install the printer
paper.
1. Press the latch above the paper compartment door to release the door.
2. The printer paper is a single side thermal paper, and the smoother side that
has temperature sensitive coating on it shall be installed upside.
3. Pull the end of the paper out of the compartment and close the printer door.
If the Error indicator lights off, the printer paper has been installed properly;
if not, repeat the procedure specified above.
NOTE
Use the specified printer paper only. Other printer paper may cause the printer to print
with poor quality, function improperly or not at all, or bring damage to the thermal print
head.
If the printer is not properly connected, the information Printer is not probed correctly!
will be displayed at the lower left part of the Set Printer Parameters dialog box.
Do not open the printer door when the printer is in work.
Do not install any other types of printer to this monitor, otherwise the monitor will be
damaged. If you have any doubt, please contact the manufacturer in time.
CHAPTER 8:
TRENDS
OVERVIEW
The trend data is the patients data collected along with the time accumulation. The trends function
displays the patients status graph (trend graph) and status table (trend table) according to the trend
data and can be used for reviewing the waveforms and parameter values at a certain time to judge
and dispose about the patients status properly. If the monitor is equipped with a printer, the trend
graph can be printed.
59
This monitor has two methods to display trend graph (table), one is to display it in channels area,
and the other is to display it in trend window.
TREND CHANNELS
The trend graph (table) can be displayed in channels area, so that the waveforms, measured
parameter values and their trend can be viewed at the same time. The trend graph (table) channel
displays the latest real-time trend data distribution, and the parameters can be selected. Turn to the
time concerned and adjust the time zoom spans.
Press the Main menu key to enter the Main menu, select Display, and then select Format Setup to
pop up the Setup Display Channel diaglog box. In this dialog box, select the Graph (Table), then
select Ok, the trend graph (table) will be displayed in the channels area, shown as below.
Trend graph
channel
Trend table
channel
TREND GRAPH CHANNEL

Distribution
Parameter label: Select this label to enter the trend graph channel menu.
Measure scale: Mark the value scale on the trend graph.
Trend graph area: The trend graph is displayed in the upper part, while the time scale in the
lower.
In the ordinary status, the trend graph of the latest time quantumn is displayed in this area. When the
data is more than one screen, the graph automatically rolls left. Select Last Page to review the earlier
trend graph, and Next Page to review the later trend graph. The graph color is determined by the
parameter. When the parameter value is void, its graph is grey.
60
Menu
Selecting the parameter label in trend graph channel pops up the following trend graph channel
menu.
Select Param
Selecting Select Param pops up the following menu. Select the desired parameter in this menu,
the corresponding trend graph will be displayed in the trend graph area.
Last Page and Next Page

Turns the trend graph backward or forward.
Step
Selecting Step pops up the following menu. The graph will be compressed and the new graph
will be added according to the selected step.
Range
Selecting Range pops up the following menu.
The ordinate value range of the trend graph can be set in this menu. When the range is set, the
trend data takes it as the upper limit/lower limit, and the value exceeds the limit is void.
Alarm Limit: Take the values about the default alarm limits as the range. It is the default
ordinate range.
Max Range: Take the default maximum and minimum values as the range.
Manual Adjust: Adjusts the range by turning the rotating mouse manually. But this range is
confined by the Max Range.
TREND TABLE CHANNEL

Distribution
Table label: Select this label to enter the trend table channel menu.
Data area: In the ordinary status, the trend data of the latest time quantum is displayed in this
area. When the data is more than one screen, it automatically rolls up. The Last Page, Line Up,
Line Down and Next Page buttons can be used to review the trend data of the time concerned.
61
Menu
Selecting the table label pops up the following trend table channel menu.
Line Up, Line Down, Last Page and Next Page

Adjusts the time of trend data forward or backward.
Step
Selecting Step pops up the following menu. The data will be compressed and the new data will
be added according to the selected step.
TREND WINDOWS
Select Review in the Main menu, then select Trend, the trend graph window pops up. It can be
changed to trend table window via the Table button in the displayed menu.
62
TREND GRAPH WINDOW
Distribution
1 Parameter mark: The corresponding parameters of the three graphs displayed in the trend
graphs area.
2 Scale: Marks the value range of the trend graph.
3 Cursor: Move this cursor via the Cursor button.
4 Parameters table: The parameter values at the current time are displayed in this table. The
inverse black text is the selected parameter, and the lower part of the list is the event and step. If
there is a recorded event at the current time, the event number will be displayed on the right
side of Event. The current step is displayed on the right side of Step. See CHAPTER 9:
EVENTS for detailed information about the event.
5 Trend graphs area: Displays the trend graph of the selected time quantum. The graph color is
determined by the parameter. When the parameter value is void, its graph is grey.
6 Starting time of the trend data: The time that the monitor starts to record the trend data.
7 Current time: The corresponding time of the cursor positon.
8 End time of the trend data: The time that the monitor stops recording the trend data.
9 The mark of the current time in the trend data record time: Marks the positon of the current
time in the whole trend data record time with red point.
10 Event mark: Marks the event recorded in the current page with point in different color. Yellow
point marks event 1, green point marks event 2, blue point marks event 3 and pink point marks
event 4. See CHAPTER 9: EVENTS for detailed information.
Time scale: Marks the time scale of the current page.
Menu
The trend graph window menu is displayed as the following:
63
Select Param
Selecting Select Param pops up the following menu. One to three desired parameters could be
selected in this menu. The selected parameter is displayed with inverse figure in the parameters
table. Selecting a parameter again will cancel the selection. Select OK to confirm the selection,
and the corresponding trend graph will be displayed.
Last Page and Next Page

Turns the trend graph backward or forward.
Cursor
Select Cursor and rotate the mouse, the cursor on the trend graph will move in accordance with
the rotating direction, and the parameter values and events will be displayed in the parameters
table. Pressing the rotating mouse again will exit the cursor moving status.
Step
Selecting Step pops up the following menu. The graph will be compressed and the new graph
will be added according to the selected step.
Range
Selecting Range pops up the following menu.
The ordinate value range of the trend graph can be set in this menu. When the range is set, the
trend data takes it as the upper limit/lower limit, and the value exceeds the limit is void.
Alarm Limit: Take the values about the default alarm limits as the range. It is the default
ordinate range.
Max Range: Take the default maximum and minimum values as the range.
Manual Adjust: Adjusts the range by turning the rotating mouse manually. But this range is
confined by the Max Range.
Print
Selecting Print pops up the following menu.
In this menu, you can select to print the trend graph of current page, last 8 hours, last 12 hours
or last 24 hours. Only the trend graph displayed on the top part of the trend graphs area is
printed.
64
TREND TABLE WINDOW
Distribution
The DAY-TIME is displayed on the left part of the trend table. On the top is the
latest time. From the upper to the lower, the interval between two adjacent
times depends on the preset step. The central time of the table is the current time of the
trend graph. The right of the DAY-TIME is the parameter names and parameter day-
time values (except NIBP which is the first value in the current step). The
symbol "---" means the parameter is not measured at the corresponding time.
Menu
The trend table window menu is displayed as the following:
Line Up, Line Down, Last Page and Next Page

Adjusts the time of the trend data forward or backward.
Step
Selecting Step pops up the following menu. The data will be compressed and the new data will
be added according to the selected step.
Graph
Selecting Graph enters the trend graph window.
65
CHAPTER 9:
EVENTS
This monitor provides events to define the situations, such as dose taking, injections or
therapy, which have influence on patients and parameter monitoring. A mark
will be displayed on the trend graph window indicating the time the mark was
initiated in relation to the event it represents.
RECORD EVENTS
Selecting Event in Tools menu pops up the following Events dialog box.
The events to be recorded.

Prompt information.
This dialog box allows you to mark four different events. Select Event 1, Event 2,
Event 3 or Event 4, the monitor will record corresponding events.
For example, if the injection is defined as event 1, when taking an injection, select Event 1, the
monitor will record the current time and display prompt information Set Event 1 OK at the lower
left part of the dialog box if records successfully.
BROWSE EVENTS
There is event point under the time scale on the trend graph window in different color to mark event.
Yellow point marks event 1, green point marks event 2, blue point marks event 3 and pink point
marks event 4. The Last Page, Next Page and Cursor buttons can be used for reviewing the time and
parameter values when an event happens. For detailed information, see TREND GRAPH WINDOW
in CHAPTER 8.
66
CHAPTER 10:
DRUG CALCULATOR
The drug mixture used for intravenous transfusion involves the information such as the drug dosage,
infusion speed, amount, volume, and concentration. The drug calculator can calculate the unknown
value via the known items to help you to control the drug infusion.
WARNING
Before using any drug, you shall check whether the correct calculation unit or patient
weight have been selected, if have problems, please consult the dispensary in your
hospital.
It must be the doctor to determine the drug and its dosage. The drug calculator calculates
the dosage based on the input values and cannot verify the validity of the calculated data.
ENTER DRUG CALCULATOR

Select Tools in Main menu, and then select Drug Calculator, the following Drug Calculator window
pops up.
UNIT
Drug unit
When the drug is Any Drug, g, mg, mcg, unit, k unit, m unit or mEq can be selected.
When the drug is selected, the drug unit is set by the drug calculator automatically, and the user
cannot modify it.
When the drug unit is selected, the units relating to the weight in the Drug Calculator, Drip Table and
Titration Table will change correspondingly.
67
Time unit
Options: min (minute) or hr (hour).
When the time unit is selected, the units relating to the time in the Drug Calculator, Drip Table and
Titration Table will change correspondingly.
TERMS
Amount
The total weight of the drug used within certain time.
Volume
The volume of the mixture is formed by drug diluents and drugs.
Dose/min (Dose/hr)
The drug quantity injected in a minute or an hour.
Dose/(kg*min), dose/(kg*hr)
The drug quantity injected into 1kg of patient weight in a minute or an hour.
Dose/(kg*min) WeightDose/min
Dose/(kg*hr) WeightDose/hr
Rate
The volume of the mixture injected in a minute or an hour. The unit is ml/min or ml/hr.
Rate/kg
The volume of the mixture injected into 1kg of patient weight in a minute or an hour. The unit
is ml/min or ml/hr.
Rate/kg WeightRate
Time
The consumed time for drug transfusion. The unit is min or hr.
Concentration
The concentration of the mixture formed by the drug diluents and drug.
ConcentrationAmount / Volume
Drip/min (Drip/hr)
The gutta of the mixture transfused in a minute or an hour.
Drip/ml
The volume of each gutta dropped form the transfusion device. The unit is GTT.
DRUG CALCULATOR
NUMERIC INPUT BLOCK

The number is inputted according to the digit. When entering the numeric input block, the
numeric input block selects the first digit at left, turn the rotating mouse, the numeric input
block selects each digit consecutively from left to right, when it reaches the last, it jumps to the
next input block.
The selection range for each digit is 0~9.
When the digit is greater than the display value, it displays ---.--, and when it less than the
display value, it displays 0.00.
When it cannot display all digits, the round is adopted.
CALCULATION FORMULA
The relational formula of the drug weight
68
Amount = Dose/min Time
Dose/min = Dose/(kg*min) Weight
The relational formula of liquid volume
Volume = Rate Time
Rate = Rate/kg Weight
Concentration = Amount / Volume
KNOWN ITEM AND CALCULATION RESULTS

Amount, Dose/min, Dose/(kg*min), Volume, Rate, Rate/kg, Time and Concentration can be
inputted as the known items or be outputted as the calculation results.
At least three known items should be inputted according to the calculation requirements, and
the drug calculator automatically calculates the item that has computation relationship with
them.
The known item is expressed with digit in blue background, and the calculation result is
expressed with digit in gray background.
When enters this window, all items are displayed as 0.00 and can be inputted. When a known
item is inputted, the result will be displayed in real-time and locked, the user only can modify
the known item. Modifying the input item as 0.00 means canceling this input.
The Reset button restores all the items to the initial status.
CALCULATION FOR ANY DRUG

When the Drug selection is Any Drug, the Drug Calculator only provides the calculation with
no application range prompt for the dose, concentration etc.
Input the Weight, Drug Unit and Time Unit.
Input the kown item, and the drug calculator will calculate relevant item.
CALCULATION FOR EXACT DRUG

The drug calculator has been preset more than ten general drugs calculation, including
Aminophylline and Amrinone Lactate (refer to Drug dosage range limitation table). When
select the drug, the Concentration, Amount and Dose/min (or Dose/(kg*min)) have range
limitations. If the input item or calculation result is out of the range, it will be expressed in
yellow digit.
The drug dosage over range prompt only prompts the user to pay attention to use appropriate
dose of the current drug, the final transfusion dose and transfusion process are determined by
the doctor.
69
Drug dosage range limitation table
English name Concentration Dose/min (Dose/(kg*min)) Amount

Aminophylline 1mg/ml 25mg/min 250~500mg
Amrinone Lactate 1~3mg/ml 5~10ug/kg/min 250~500mg
Bretylium Tosilate 10mg/ml 1~50mg/min 5~10mg
Dobutamine 5mg/ml 2.5~40ug/kg/min 250mg
Dopamine 3mg/ml 1~30ug/kg/min 10~20mg
Epinephrine <64ug/ml 1~4ug/min 0.025~1mg
Heparin Sodium 20~40U/ml 15~20U/kg/h10% 6000~20000U
Isuprel 2~4mcg/ml 2~20mcg/min 500~1000mcg
Lidocaine 8mg/ml 1~4mg/min 50~100mg
Morphine 5mg/ml 2mg/min 5~15mg
hydrochloride
Nitroprusside 1mg/ml 0.5~10ug/kg/min 50mg
Nitroglycerin 50~400ug/ml 5~200ug/min 5~10mg
Oxytocin 0.01U/ml 0.001~0.04U/min 2.5~5U
Procainamide 2~4mg/ml 1~6mg/min 500~750mg
DRIP TABLE
Select Drip Table in the Drug Calculator window, the following information window appears that
shows how much liquid is transfused and how much time remains.
The Drip Table displays the residual quantities of the drug and liquor at each time quantum
when the user inputs the data into the Drug Calculator window.
The left side of the widow shows the data inputted by the user (and calculation result) in the
Drug Calculator window, the right side lists the amount and volume at 15 time quantums that
are equally divided from the Time.
All items in this window cannot be modified.
In the table, the unit relating to the weight is the same as the unit in the Drug Calculator
window, and the volume unit is ml.
Select Ok to exit the Drip Table window and return to the Drug Calculator widow.
70
TITRATION TABLE
Select Titration Table in the Drug Calculator window, the following information window appears
that displays the dosage at different rates. The higher the rate is, the greater the steps between the
items are.
The Titration Table shows the dose (Dose/min or Dose/hr) at different rates with the same
concentration.
The left side of the widow shows the data inputted by the user (and calculation result) in the
Drug Calculator window, the right side shows the dose (Dose/min or Dose/hr) at 30 rates,
which are equally divided from the range in the benchmark item.
In the list the user has two items such as Dose and Rate.
The range of Dose/min (Dose/hr) is the one to two times as the dosage inputted in the Drug
Calculator window.
Select Ok to exit the Titration Table window and return to the Drug Calculator window.
RESET
Exit the Drug Calculator window or turn off the monitor, the drug calculator data inputted by the
user and the calculation result are still saved. When the user enters the Drug Calculator window
again, the latest calculator dada shows. Selecting Reset in the Drug Calculator window clears the
inputted data and starts a new calculation.
71
CHAPTER 11:
OTHER PATIENT VIEWING
OVERVIEW
This monitor is able to view waveforms and measured parameter data from
another patient monitor on the same monitoring network.
The other patient viewing function has the following features:
The other patient viewing function must be realized by the LAN, so the viewing and viewed
monitors should both be connected to the LAN.
The LAN connection could be wire or wireless.
The other patient viewing function doesnt depend on the central monitoring system. Whether
the central monitoring system exists in the LAN doesnt influence this function.
A monitor only can view one monitor and at the same time, only can be viewed by one monitor.
SELECT MONITOR
Select Tools in the Main menu, and then select Other Patient, the following Other Patient--Select
Monitor dialog box pops up.
All the device names of the monitors connected to the LAN are listed in this dialog box, such as
101 displayed in the figure above. The device name is set in the Edit Device Name dialog
box and its detailed setting method refers to NETWORK SETTINGS in CHAPTER 4.
One page of this information box can list 12 device names. When the connecting monitors
exceed 12 sets, the device names will be displayed in divided pages and can be checked via the
Prev. and Next buttons that arent displayed if the connecting monitors are less than 12 sets.
When the viewed monitor alarms, its device name is in red background, and the button restores
to blue background when the viewed monitor no longer has physiological alarms.
If the same device names exist in a LAN, they will be listed as device name * serial No. in
72
this dialog box.
Turn the rotating mouse to select the desired device name, and then press the rotating mouse to
check the waveforms and parameter values of the corresponding monitor.
This information box cant exit automatically, you can select the Ok button or press the Main
menu key on the front panel to exit.
A monitor only can be viewed by another monitor, if select a monitor viewed by another, the
Other Patient information box will pop up, shown as below (101 is the selected device name).
OTHER PATIENT
Select the desired device name in the Other PatientSelect Monitor dialog box, the following
window pops up.
All the real-time parameter values of the viewed monitor are displayed in the lower part of this
window. If a parameter value exceeds the alarm limit of the viewed monitor, it will be
displayed in red.
The parameter alarm doesnt change the audible alarms status of viewing monitor. The
parameter alarm is related with the alarm limit of the viewed monitor, and has no relation with
the alarm switch, alarm tone of the viewed monitor and the relevant alarm settings of the
viewing monitor.
A real-time waveform of the viewed monitor is displayed in the waveform area. There is a
waveform selection field at the top left conner, select it, and the displayed waveform will
switch among all the parameter waveforms.
This window cant exit automatically, you can select the Ok button or press the Main menu key
on the front panel to exit.
73
CHAPTER 12:
ECG MONITORING
OVERVIEW
This Monitor adopts 5-lead (or 3-lead) ECG cable to collect the ECG signal from the patient, and it
can simultaneously display seven (or three) leads of ECG signal. ECG channel displayed on the top
part of the screen is the major channel of the ECG signal, and its lead is called the major lead. The
Monitor calculates the heart rate value and controls the gain (if set in automatic mode) according to
the data of the main lead. All leads adopt the same gain and same measurement mode. The Monitor
can separately check whether the connection of a lead has fallen off, and display the promt
information in corresponding channel.
1.Measurement of ECG
The electro-chemical activity of Excitable cell will produce physiological current
to cardiac muscle before the mechanical shrinkage of heart, the close movement
current produced by the process of heart exciting will flow within the human body and
transport to all parts, it results in the different voltage on the different surface of body.
The clinic Electrocardiography is to record the voltage difference real time.
Figure 2.1 is the Electrocardiography
R
P
T u
QS
2.1 Figure
1.1Electrode of ECG
Current within human body is conducted by hydronium, while its by electron in
metal conductor, so there should be a conversion medium to convert the hydronium
current to electron current, which will help realize the necessary connection between
the human body and patient monitor, electrode is to play the role to realize the
transformation. The widely used electrode for clinic monitoring is AgAg.Cl disposable
electrode.
1.2. ECG leads

The definition of lead is the periodically changing waveform with heart beating
caused by the voltage between two or more than two surface parts of human body.
One lead waveform can only reflect one aspect of the heart movement since the
74
heart is solid, so its necessary to record several leads waveforms to reflect the
complete movement of heart from different respects during the process of diagnosing.
Below table is the definition for the different leads of ECG:
Table 2.1: Definition for different leads of ECG
Name of leads Definition of leads Nominate of leads
=LA-RA Standard double poles limb lead
=LL-RA Standard double poles limb lead
=LL-LA Standard double poles limb lead
aVR aVR=RA-(LA+LL)/2 Pressure single pole limb lead
aVL aVL=LA-(LL+RA)/2 Pressure single pole limb lead

aVF aVF=LL-(LA+RA)/2 Pressure single pole limb lead
V=V-(LA+RA+LL)/3 Pressure single pole limb lead
Our patient monitor adopts five leads ECG cable to collect signal of patients ECG.
It displays synchronously seven ECG waveforms. The fixed channel of ECG displayed
on the upper position is the main one of ECG signal, we call the ECG lead which the
main channel choose main lead, patient monitor calculate the value of heart rate and
control the gain based on it (if them monitor is set to model of Auto gain). We have the
same gain control and test mode to all leads, the patient monitor is able to check
whether the corresponding electrode of leads is fall off and display it on screen.
2.Monitoring of ECG electrode

It can get mostly twelve selectable ECG leads if use five leads ECG cable to monitor patients
ECG, the ECG waveform of this lead of patient will be displayed when the leads is set as valid.
The ECG cable includes two parts: main stem cable which connected to patient monitor and
Lead cable electrode which connected to patients, usually the ECG cable has five electrodes, please
note below items when place the electrodes to patients:
1 How to choose and use electrodes
It usually chooses Ag-AgCL one-off electrode, please make sure the electrodes are during the
period of validity. It will result in inaccurate data if use the incompetent electrodes.
2 Pretreatment of skin
Its necessary to pre-treat the skin of patient to ensure the good touch between electrode and
patient since the skin is not a good conductor.
(1) Clean the skin with soap and water instead of aether and alcohol since the later two will
increase the resistance of skin.
(2) Shave off the fur of body where to place the electrode if necessary.
(3) Rub skin to increase the blood floor of capillary vessel of organization and get ride of the
horn and grease.
75
(4) Place the electrode to patient, please apply conductive cream before the electrode is put to
patient if the electrode do not have conductive cream.
(5) Connect the electrode and ECG cable.
(6) Make sure the connection of patient monitor power.
ECG MONITORING
In order to monitor the patients ECG, we use a five-electrode ECG cable by which we can get more
than 12 selective ECG leads. If a lead is effective, the corresponding waveform will be displayed in
the channels area.
The ECG cable includes two parts: the main cable connecting the Monitor and the electrode lead line
connecting the patient.
PREPARATION
1. Select electrode
Generally, the electrode for monitoring is disposable electrode made from Ag-AgCl (silver -
silver chloride). But before use, you shall confirm that the electrode is within the valid date. If
the unqualified electrode is used, it will lead to inaccurate monitoring result.
2. Skin pretreatment
Because the skin is not a good conductor, if you want to gain good contact between the skin and
the electrode, before installing the electrode, you shall carry out skin pretreatment at first.
(1) If necessary, shave hair from skin at choosen site.
(2) Rub the skin to accelerate the blood flow in the blood capillary of organs and remove the
horny layer and greases of the skin.
(3) Thoroughly cleanse the site with mild soap and water solution, but do not use the aether
or pure alcohol, because it will increase skin resistance.
(4) Dry the skin completely before applying the electrodes.
3. Attach the ECG lead to the electrodes prior to placement.
4. Place the electrode on the patient. If the conductive ointment is not applied to the
electrodes, apply it before the placement.
5. Connect the electrode lead to the patient cable.
6. Confirm the Monitor is powered on and is ready for monitoring.
ELECTRODE PLACEMENT
(1) For the placement of the fivelead ECG electrode, refer to the figure as shown in Figure 12-1.
76

Figure 12-1 Positions of 5-Lead Electrode Placement
NOTE
The sign name and color of the electrode shown above is American standard, while inside
the brackets ( ) is European standard.
White (right arm or RA) electrode: near the right shoulder, directly below the
clavicle.
Black (left arm or LA) electrode: near the left shoulder, directly below the clavicle.
Green (right leg or RL) electrode: on the right abdomen.
Red (left leg or LL) electrode: on the left abdomen.
Brown (chest or V) electrode: on the chest.
(2) When using five leads, attach the chest (V) electrode to one of the
following positions indicated in Figure 12-2:
Figure 12-2 Positions of Chest Electrode

In order to accurately install and monitor the "V" lead, it is very important to determine the
fourth rib position, which is determined according to the first rib position. Because of the
patients different bodily forms, it is difficult to accurately feel out the first rib position. At
first, feel out the small protruding body called the "Lewis angle", where the breastbone
diaphysis and manubrium sterni joint. Then determine the second rib position, the protuberant
section of the breastbone indicates the joint of the second rib, right under here is the position
of the second rib position, from the chest to feel down until the fourth rib position is
determined.
Attach the chest (V) electrode to one of the following positions indicated in
Figure 12-2:
77
V1: On the 4th intercostal space at the right sterna margin.
V2: On the 4th intercostal space at the left sterna margin.
V3: Midway between V2 and V4 electrodes.
V4: On the 5th intercostal space at the left clavicular line.
V5: On the left anterior axillary line, horizontal with V4 electrode.
V6: On the left middle axillary line, horizontal with V4 electrode.
V3R-V7R: On the right side of the chest in positions corresponding to
those on the left.
VE: Over the xiphoid.
When attaching the chest electrode to the back of a patient, place it at
one of the following sites:
V7: On the 5th intercostal space at the left posterior axillary line of the
back.
V7R: On the 5th intercostal space at the right posterior axillary line of
the back.
(3) Electrode placement for pacemaker patient

The pacemaker lead can pick up the best ECG waveform from the pacemaker patient. At this
time, the electrode is usually placed on the mammillary line, the white and black electrodes
are placed as shown in Figure 12-3.
Red (green)
White (red) Black (yellow)
Figure 12-3 Positions of Pacemaker Patients Electrode
(4) Electrode placement for surgical patient

Electrode placement during surgery is dependent on the type of surgery
being performed. For example, with open chest surgery, the electrodes
might be placed laterally on the chest or on the back. In the operating
room, artifact can sometimes affect the ECG waveform due to the use of
electrosurgery equipment. To help reduce this, place the electrodes on the
right and left shoulders, the right and left sides near the stomach, and
place the chest lead on the left side at mid-chest. Avoid placing the
electrodes on the upper arms. This will cause the ECG waveform to be too
small.
NOTE
Select the place with stable ECG signal or little inference of skeleton activities to place the
78
electrodes.
WARNING
In order to ensure the patients safety, all leads shall be connected to the patient.
The electrode shall be fixed properly to ensure the reliable contact of the conductor with
skin.
Interference from a non-grounded instrument near the patient and ESU interference can
cause inaccuracy of the ECG waveform.
When using Electrosurgery equipment, never place the ECG electrodes near the
grounding plate of the Electrosurgery device. This will cause a great deal of interference
with the ECG signal. The patient leads should be placed in a position that is equal
distance from the Electrosurgery electrotome and the grounding plate to avoid burns to
the patient.
Always dispose of, or recycle electrodes properly to prevent from environment
contamination.
Verify the lead fault detection prior to the start of monitoring. Unplug the ECG cable
from the ECG connector, the flashing error message Lead Off will be displayed in the
corresponding ECG channel.
Skin irritation may result from the continuous application of the ECG electrodes. These
should be checked each day. If there is an indication of excess skin irritation, replace the
electrodes or change the location of the electrodes every 24 hours.
ECG CHANNEL
MAIN LEAD CHANNEL
The top part of the channels area that cannot be changed to any other channels is called as the main
lead channel, shown as below:

Main lead label gain mode gain measurement mode

Waveform speed ECG waveform scale range scale
Select the main lead label, the ECG channel menu shows as the following.
Lead
79
Select this button, the main lead switches among I, II, III, aVR, aVL, aVF and V. In order to get
accurate heart rate and gain control performance, the doctor shall select the lead of large range
and little noise as the main lead.
In order to avoid emerging leads repeatedly, when the lead in the current channel is switched,
the leads in the other channels will be changed automatically.
Gain Mode
Select this button, the gain mode switches between AUTO and MANUAL modes.
Gain means the magnification times for the ECG waveform signal. This monitor has five
magnification times that are 1/4, 1/2, 1, 2 and 4. The 1 is one time magnification,
under which the range of the scale at the left side of the ECG waveform is 1mV. Then
under the condition of 2 magnification, the range of the scale is 0.5mV, and so on.
Detailed data refers to the following table:
Gain factor AUTO MANUAL Scale range

1/4 Adopted Applicable 4 mV
1/2 Adopted Applicable 2 mV
1 Adopted Applicable 1 mV
2 Adopted Applicable 0.5 mV
4 Adopted Applicable 0.25 mV
Under 1 ECG and Huge Digit display format, the length of the scale is 10mm. The
waveform of 10mm diaplayed under 1 magnification times means the ECG signal is 1mV,
under 2 means 0.5mV.
NOTE
All leads including the main lead and other leads adopt the same gain.
This Monitor provides two methods to regulate the ECG waveform range:
AUTO mode: Under the AUTO mode, according to the main lead waveform data, the
Monitor will automatically regulate the gain to amplify the ECG waveform of the main
lead without the distortion as possible. The defect of this mode is slow regulation speed.
MANUAL mode: Under this mode, the Monitor doesnt regulate the ECG gain
automatically. At this time, the ECG gain is regulated via the Adjust Gain button. The
feature of this mode is fast response that the waveform will change immediately after the
gain is regulated, and the waveform can be amplified to a distortion status to display.
Adjust Gain
Manually regulates the ECG gain. After selecting this button, regulate the gain via the rotating
mouse. Rotate counterclockwise, the gain and waveform range become smaller, while rotate
clockwise, the gain and waveform range become larger. After the accomplishment of the
regulation, press down the rotating mouse again to exit the gain adjusting mode.
Mode
The Mode means the filter bandwidth of the ECG channel. The monitor has three modes:
diagnosis (DIA), monitoring (MON) and operation (OPR). Under the DIA mode, the filter
bandwidth is the widest, and the detailed information of the ECG signal can be got. The more
detailed information is helpful to more accurately judge the status of the ECG signal. But when
the importation of the detailed information, the environmental noise, such as HF electrotome,
80
may be imported too. The noise mixes with the real ECG signal, so that the ECG signal cannot
be distinguished. In order to adapt to the noise interference situation, the Monitor also provides
two measurement modes, namely the MON mode and the OPR mode. Under these two modes,
narrower bandwidth is adopted to measure and gain smoother signal. The user can make
choices according to the exact situations, and the comparing data are as followings:
Mode Bandwidth Details Noise

DIA 0.05Hz~100Hz Most Most
MON 0.5Hz~40Hz Medium Medium
OPR 1.0Hz~25Hz Least Least
NOTE
All leads including the main lead and other leads adopt the same mode.
Waveform Speed
Select this button to regulate the waveform speed for parameters relating to ECG, including all
ECG channels and PLETH channel. It has four speeds such as 6.25 mm/s, 12.5 mm/s, 25 mm/s
and 50 mm/s.
OTHER LEAD CHANNELS

Other lead label scale lead off icon ECG waveform

Select the position , the current lead label switches among 6 leads (except the main lead). Labels
in different channels are different, when the lead label in the current channel is switched, the lead
label in other channels will be changed automatically.
When the ECG electrode has fallen off from the ECG cable or from the monitor, the flashing prompt
information Lead Off is displayed in corresponding ECG channel.
ECG PARAMETER
HEART RATE
Except in Huge Digit mode, the heart rate is displayed on the top part of the parameters area, shown
as below.

Lower alarm limit Upper alarm limit alarm off icon heart rate label heart rate source
sign Measured heart rate value
81
Select the heart rate label (HR), the HR menu pops up, as shown in the figure below:
Alarm On/Off
Enables or disables the HR alarm.
Alarms enabled: The HR alarm is turned on and the monitor alarms when the measured
HR value exceeds the preset alarm limit.
Alarms disabled: Icon is displayed on the left side of the HR label, the HR alarm is turned
off, and the monitor does not generate alarms when the measured HR
Alarm Setting
Select this button, the Set Alarm Limits dialog box pops up, shown as bellow:
The upper alarm limit, lower alarm limit, alarm switch and alarm printing switch of HR can be
set in this dialog box. See ALARM SETTINGS in CHAPTER 5 for detailed information.
HR Source
Auto: The monitor determines the heart rate source depending on the signal quality. ECG
takes priority of SpO2. Only when the ECG signal is bad and cannot be analyzed, the heart
rate source is SpO2. If the ECG signal becomes normal, the HR source changes to ECG
automatically.
ECG: HR is always calculated from ECG.
SpO2: If the ECG signal is seriously interfered, you can select SpO2, which means PR will
be derived from PLETH waveform. In this case, PR (SpO2) is displayed instead of
ECG (I, II, etc.) while the PR reading is displayed below. The monitor activates pulse
beeps instead of heartbeat beeps.
The heart rate source mark and heart rate label clearly show the current heart rate source. The
list is as the following:
Label Color of the heart rate value Heart rate source mark Source
HR Green I, II, III, aVR, aVL, aVF, V ECG
PR Red SpO2 SpO2
NOTE
The pulse rate and heart rate use the same alarm limit and alarm switch. No matter
where the heart rate value comes from, the alarm systems adopted are totally the same.
82
AVRG.
Select this button, the following menu pops up.
The average period for heart rate (pulse rate) and ST segment calculation can be set in this
menu.
BT.BT.: The average period is 1 heartbeat period.
4 Beats: The average period is 4 heartbeat periods.
ST On/Off
Select this button, the Set ST Switch dialog box pops up, shown as the following:
Auto: The monitor selects to display the ST segment or not automatically according to the
ECG mode. In DIA mode, displays the ST segment, and in MON and OPR mode, hides
ST segment.
Always On: Always displays ST segment in the parameters area.
Always Off: Doesnt display ST segment.
ST SEGMENT
In the default settings, the ST segment is always displayed. In MON or OPR mode, the ST
numerics might be severely distorted. The variance of the ST segment at the
waveform tracks can be measured and the result is displayed numerically in the
parameters area. Measurement symbols of the ST segment: + means positive
elevation, - means negative elevation.
The ST segment is displayed as the following:

Lower alarm limit of the main lead ST segment

Upper alarm limit of the main lead ST segment label of the main lead ST segment
Measured value of the main lead ST segment measured values of other lead ST segments
Select the label of main lead ST segment, such as ST (II) displayed above, the following menu
appears.
Alarm On/Off
83
Enables or disables all the ST segment alarms.
Alarms enabled: The ST segment alarms are turned on, the monitor alarms when the
measured ST segment value exceeds the preset alarm limit.
Alarms disabled: Icon is displayed on the left side of the main lead ST segment label, the ST
segment alarms are turned off, and the monitor does not generate alarms
when the measured ST segment value exceeds the preset alarm limit.
Alarm Setting
Select this button, the Set Alarm Limits dialog box pops up, shown as bellow.
The upper alarm limits, lower alarm limits, alarm switches and alarm printing switches of the
ST segments can be set in this dialog box. See ALARM SETTINGS in CHAPTER 5 for
MAINTENANCE AND CLEANING

The exterior surfaces of the ECG cable may be cleaned with a soft cloth, dampened with the
alcohol, and then be air-dried or dried with a clean dry cloth.
WARNING
If the ECG cable is damaged or aging, it shall be replaced by a new one.
Before cleaning the ECG cable, be sure to disconnect the monitor from the ECG cable, or
shut down the system and disconnect all power cords from the outlet.
TROUBLE SHOOTING
Problem Possible reasons Suggestions and way out

Lead off The ECG electrode has fallen off Ensure the electrode, lead and cable are
from the patient or from the properly connected.
Monitor.
ECG signal The mode is not correctly set Change the mode.
noise is too according to the environment.
loud The power frequency is not set in Set the power frequency properly. Refer to
accordance with the local power REGION SETTINGS in CHAPTER 4 for
frequency. detailed information.
The Monitor is bad grounding. Check the grounding system of the Monitor.
The electrode is badly connected to Keep the patient quiet, and guarantee the
84
the patient. reliable connection of the electrode.
No heart rate The ECG signal is very weak. Check the connection between the electrode
is displayed; (<0.25mV) and patient, ensure the reliable touch of the
No heartbeat The electrode is badly connected to electrode and patients skin.
beeps the patient.
The patient type is not correctly set. Correctly set the patient type.
The gain is not enough. If it is in the MANUAL mode, please turn
the gain to a right magnification.
CHAPTER 13:
RESP MONITORING
OVERVIEW
This Monitor measures out the respiration movement waveform by the ECG cable with the
impedance method. This respiration movement waveform is used to calculate the respiration rate and
analyse the respiration status.
The Monitor can measure three lead respiratory waveforms such as I, II or III lead, of which, the II
lead is generally used. Because of the different signal strength, the Monitor provides AUTO and
MANUAL modes to adjust the gain. The respiratory waveform will be clear and without distortion if
an appropriate gain is adopted.
ELECTRODE PLACEMENT
The impedance respiration method of this Monitor is to monitor the patients respiration by the
impedance variation between the two electrocardiogram electrodes of I, II or III lead. Since the
same electrodes are used for ECG and RESP monitoring, the electrode
placement is very important. Some patients, due to their clinical condition,
expand their chest laterally, causing a negative intrathoracic pressure. In these
cases it is better to place the two electrodes used for RESP monitoring laterally
in the right axillary and left lateral chest areas, at the maximum point of the
breathing movement, to optimize the respiratory waveform.
NOTE
RESP monitoring is not recommended on very active patients, because it will cause false
alarms.
Place the red and white electrodes diagonally to optimize the respiration waveform.
Try to avoid placing the electrodes so the liver area and the ventricles of the heart are in
path between the electrodes used for respiration, to avoid cardiac artifact to overlay on
the ECG. This is particularly important when monitoring neonate patients.
85
White (red)
White (red)
Red (green)
Red (green)
The electrode placement procedure refers to PREPARATION in CHAPTER 12.
MONITORING INTERFACE
The RESP monitoring displays a RESP waveform in channels area and the measured respiration
rate value in parameters area.
RESP CHANNEL
Principal of impedance respiration monitoring
The movement of the thorax in the moment of the respiration will cause the
variation of the human bodys impedance, the range of the variation is about 0.1 3,
G3 Monitor immits the human body a safe electric current which is 0.5 5mA by using
two electrode of the ECG lead with the 20K 100KHZ carrier frequency sinusoidal
constant current, and then mesures out the difference of respiration impendace from
electrode LLRA . This difference of the respiration impedance shows the dynamic
waveform of respiration
Using the impedance respiration method, G3 Monitor can measure out the human body
respiration movement waveform by using the electrocardiogram lead line, and this
respiration movement waveform can be used to the calculation of the human body
respiration rate and the analyse of the human body respiration status.
The G3 Monitor measure three lead respiration waveforms according to the selection
such as I, II, III, the II lead is generally used. Because of the different signal strength,
the Monitor provides two kinds of gain adjustment functions : automatic adjustment and
manual adjustment, it can make the respiration waveform clear and without distortion by
adopting appropriate gain.
The electrode connection
The impedance respiration method of this Monitor is to monitor the patients respiration
by the impedance variation between the two electrocardiogram electrodes. The
respiration monitoring is realized via the electrocardiogram I, II or III lead and their
86
corresponding electrodes, so no additional electrodes are required, and the installation
of the electrode is very important. For some patient, because of their clinical situation,
the horizontal expansion of the thoracic cage leads to the negativity thoracic cage
internal pressure, under this situation, it is better to put the two respiration electrodes at
the central line of the right armpit or the most active area on the left side of the thoracic
cage when breathing, so that the optimum respiration wave is gained.
We suggest installing five lead electrodes for the respiration monitoring, as shown in
Figure 3.4
Notice
The respiration monitoring is not recommended to be used on the patient
who will move or be moved a lot, because it will lead to mis-alarm.
In order to obtain optimum respiration wave, the white and the red
electrodes shall be installled catercorner. Avoid putting the liver and the
ventricle on connecting line, which can avoid the false difference
produced by the heart coverage or pulsation blood flow, this is very
important in the using for neonate.
RESP channel is shown as the figure below:

1 RESP channel label. Select this label, the menu as the following figure shows pops up.
2 Lead type: I, II or III.
3 Gain mode: AUTO or MANUAL.
4 Gain: Four grades are available: 1/2, 1, 2 and 4. If the gain is too great, the top
part of the waveform may be displayed as a straight line.
5 Status prompt bar.
6 Waveform speed. Four grades are available: 6.25mm/s, 12.5mm/s, 25mm/s
and 50mm/s.
7 RESP waveform.
8 Scale.
9 Scale range. The unit is Ohm, and the length and range are different from time to time along
with different gains.
Select the RESP channel label, the following RESP menu appears:
87
RESP mode: Select this button, the channel switches to T-RESP channel.
Gain Mode: Select this button, the gain mode switches between AUTO and MANUAL modes.
Adjust Gain: This button is available only in manual mode. Select this button then turn the
rotating mouse to adjust the gain. Four grades are available: 1/2, 1, 2 and 4. Press the
mouse to exit the gain adjustment, and the RESP waveform will be displayed in chosen gain.
Lead: Select this button, the waveform switches among the waveforms of I, II and III leads.
Waveform Speed: Select this button, the waveform speed switches among 6.25mm/s, 12.5mm/s,
25mm/s and 50mm/s. Decrease it, the waveform is compressed, and you will see longer time
quantum; increase it, the waveform is expanded, and you will get more detailed view.
The Waveform Speed button in the Display menu also can be used to change the RESP
waveform speed. No matter which method is used, it will change both the waveform speed of
the RESP and T-RESP simultaneously.
RESPIRATION RATE
The respiration rate is displayed in the parameters area, shown as below:

Lower alarm limit. The monitor generates alarms when the measured respiration rate value is
less than it.
Upper alarm limit. The monitor generates alarms when the measured respiration rate value is
greater than it.
Respiration rate label. Select this label, the following menu appears.
Measured respiration rate value.
Select the respiration rate label (RR), the following menu pops up:
Alarm On/Off: Enables or disables the RR alarm.

Alarms enabled: The RR alarm is turned on and the monitor alarms when the measured
RR value exceeds the preset alarm limit.
Alarms disabled: Icon is displayed on the left side of the RR label, the RR alarm is turned
off, and the monitor does not generate alarms when the measured RR value
exceeds the preset alarm limit.
Alarm Setting: Select this button, the following Set Alarm Limits dialog box pops up.
The upper alarm limit, lower alarm limit, alarm switch and alarm printing switch of RR can be
set in this dialog box. See ALARM SETTINGS in CHAPTER 5 for detailed information.
88
RR Source: Select this button, the following menu pops up.
The respiration rate source can be viewed and selected in this menu. There are four options:
Auto, RESP, T-RESP and CO2. The monitor will display the RR value calculated from the
chosen source. If it is set as Auto, the RR source is in accordance with the current channel,
which is RESP when RESP channel is displayed or T-RESP when T-RESP channel is displayed.
PROMPT MESSAGES
In the status prompt bar of the RESP channel, the current respiration status message is displayed at
the position .
Lead Off: The current lead is not properly connected. When the lead is not inserted on the Monitor
or connected to the patient, this message shows.
Running: Except the abovementioned condition, the system prompts Running.
CHAPTER 14: T-
RESP MONITORING
T-RESP CHANNEL
Principal of the nasal tube respiration monitoring

The respiration will cause the flow of the air in the nasal tube, this flow cause the variation of the
thermistances value. By obtaining this variation, the nasal tube respiration monitoring works.
T-RESP monitoring is the nasal tube respiration monitoring. In the default settings, the RESP
channel is displayed, and it can be switched to the following T-RESP channel via RESP mode button
in the RESP menu.

T-RESP channel label. Select this label, the T-RESP menu pops up.
Status prompt message. Always shows Running.
Waveform speed. Four grades are available: 6.25mm/s, 12.5mm/s, 25mm/s and 50mm/s.
T-RESP waveform.
T-RESP MENU
Select the T-RESP channel label, the following menu appears:
89
RESP mode: Select this button, the channel switches to RESP channel.
25mm/s and 50mm/s.
The Waveform Speed button in the Display menu also can be used to change the T-RESP
waveform speed. No matter which method is used, it will change both the waveform speed of
the RESP and T-RESP simultaneously.
NOTE
The T-RESP respiration rate is displayed at the same positon of the RESP respiration
rate. To display it, you can set the RR Source as T-RESP or Auto. Detailed information
refers to RESPIRATION RATE in CHAPTER 13.

In case of an exception in the sampling system, check for entanglement of the tube. If the tube is not
entangled, the tube has been blocked, you should replace it with a new one.
WARNING
The nasal tube is disposable, must not re-sterilize or reuse it.
Do not press or limit the nasal tube.
The nasal tube should be recycled or disposed of, complying with the local laws.
CHAPTER 15:
NIBP MONITORING
OVERVIEW
The non-invasive blood pressure (NIBP) module measures blood pressure using the
oscillometric method. This monitor can be applied to adult, pediatric and neonate patients. Three
measurements are available: manual, auto and continuous. Each mode displays the
systolic pressure (SYS), mean arterial pressure (MAP) and diastolic pressure (DIA).
Manual: Pressing the NIBP key on the front panel starts a NIBP measurement.
Auto: The NIBP measurement is conducted automatically at a preset interval.
Continuous: The NIBP measurement is performed as many times as possible
in five minutes.
Blood Pressure Measurement Principle
NIBP measurement adopts vibration method. The principle is to charge air to blood
pressure cuff to the degree that arteries are pressed completely and the blood flowing is
blocked. And while the cuff is deflated gradually, the arteries are in the process of utter
90
blocking, gradual loosing and unobstructing. In this process the artery pressure
pulsation will generate air oscillating waves in the cuff. Theoretic arithmetic and
experiments indicates that oscillating waves have defined correspondence with artery
systolic blood pressure, mean blood pressure, and diastolic blood pressure. Hence
systolic blood pressure, mean blood pressure, and diastolic blood pressure can be
measured by analyzing measurement results and pressure oscillating waves in the cuff.
When the blood pressure measurement process starts up, the Monitor charges the air
into the blood pressure cuff, the human body blood pressure, including the systolic
blood pressure, diastolic blood pressure and mean pressure are measured out via the
sensors, a measurement process is about 40 seconds.
There are three start-up methods for blood pressure measurement, one is manual
measurement mode, the other is automatic measurement mode, and the third is
consecutive measurement mode.
mmHg
200
165mmHg
Pulse waveform
2.0 cuff pressure

100

1.0 PS Outline of pulse

Pulse oscillation waveform
0
0 Tim
e
Notices of
NIBP
Measurement
1. Korotkoff Sound Method, widely-adopted in clinics, is similar to vibration method. But there are
many coherent defects in Korotkoff Sound Method. It primarily relies on the coordination between
mans vision and hearing, thus the method is rather subjective and unduplicated. Therefore the
results by Korotkoff Sound Method can not be applied to evaluate the results by vibration method.
2. Human arterial blood pressure is a changeable physiological parameter, related
with the patients emotion, psychological change, posture and position during the
measurement. So it should be considered in measurement and evaluation.
3. The vibration measurement bases on the oscillating waves in cuff, so the
oscillation from the outside and the movement of the patients arm will affect the
measurement results. The serious consequence is the failure in the measurement. It
needs measuring again.
91
The noninvasive blood pressure (NIBP) measurement adopts the succussion;
It is applicable to adult, pediatric and neonate.
The measurement mode: manual, automatic and consecutive. Each mode displays
systolic blood pressure, mean pressure and diastolic blood pressure.
MONITORING PROCEDURE
To perform NIBP measurement on a patient, follow the procedure as below:
1. Power on the monitor.
2. Check the patient type. If the patient type is incorrect, select a correct
patient type in Patient Information dialog box.
3. Plug the air hose in the NIBP cuff connector of the monitor.
4. Apply a cuff of proper size to the upper arm or the leg of the patient.
5. Connect the cuff with the air hose.
6. Press the NIBP key on the front panel to start the NIBP measurement.
CUFF SELECTION AND PLACEMENT

1. Identify the patient limb circumference.
2. Select appropriate cuff; limb circumference is identified on each cuff.
3. Verify the cuff is completely deflated; place cuff around extremity being
used and make sure the marking matches artery location.
4. Verify the cuff is not wrapped too tightly around the limb. Excessive
tightness may cause discoloration or ischemia of the extremities.
5. Make sure that the cuff edge falls within the range of the <-> mark. If it
does not, use a larger or smaller cuff that will fit better.
NOTE
The width of the cuff should be either 40% of the limb circumference (50% for neonates)
or 2/3 of the upper arm length. The inflatable part of the cuff should be long enough to
circle 50-80% of the limb. The wrong size cuff can cause erroneous readings. If the cuff
size is in question, use a larger cuff.
The limb chosen for taking the measurement should be placed at
the same level as the patient's heart. If this is not possible, use the
following method to correct the measurement result:
92
If the cuff is placed higher than the heart level, add 0.75mmHg
(0.10 kPa) for each centimeter of difference, or 1.9mmHg (0.25kPa)
for each inch of difference.
If it is placed lower than the heart level, deduct 0.75 mmHg
(0.10 kPa) for each centimeter of difference, or 1.9mmHg (0.25kPa)
for each inch of difference.
If you are in doubt about the accuracy of any reading(s), check the patient's vital signs
by an alternative method before checking the function of the monitor.
WARNING
Use only the specified accessories for monitoring, or it will lead to the malfunction of the
Monitor.
You must not perform NIBP measurements on patients with sickle-cell disease or under
any condition where the skin is damaged or expected to be damaged.
For a thrombasthemia patient, it is important to determine whether measurement of the
blood pressure shall be done automatically.
Ensure that the setting is correctly made when performing measurements on children.
Incorrect patient type setting may cause a danger to the patient because adult blood
pressure level is higher than children.
Before the measurement, you shall confirm your configuration is suitable to the patient
(adult, pediatric or neonate).
Do not apply the cuff to a limb that has an intravenous infusion or catheter in place. This
could cause tissue damage around the catheter when infusion is slowed or blocked during
cuff inflation.
Auto non-invasive blood pressure measurements performed in long intervals may incur
ischemia and neuropathy in the limb wearing the cuff. When monitoring a patient,
examine the extremities of the limb frequently for normal color, warmth and sensitivity. If
any abnormality is observed, change the position of the cuff on the patient or stop the
blood pressure measurements immediately.
Make sure the air tubing connecting the blood pressure monitor is not blocked, twisted, or
tangled.
MEASUREMENT LIMITATIONS
Non-invasive blood pressure measurement uses the oscillometric method of
measurement. The monitor detects the regular arterial pressure pulse. In some
circumstances when the patient's condition makes it difficult to detect this
pulse, the measurement becomes unreliable and the measurement time
increases. You should be aware that the following conditions could interfere with
93
the measurement, make the measurement unreliable, prolong the
measurement, or even make a measurement impossible.
Patient movement: E.g.The patient is moving, shivering or jerking.
Cardiac arrhythmia: E.g.The patient's cardiac arrhythmia has caused an
irregular heartbeat.
Heart-lung machine: E.g. Measurements will be impossible if the patient is
connected to a heart-lung machine.

Pressure changes: E.g.The patient's blood pressure is changing rapidly over the
period of time during which the arterial pressure pulses are being analyzed
to obtain the measurement.
Severe shock: E.g.If the patient is in severe shock or hypothermia, reduced
blood flow to the peripheries will cause reduced pulsation of the arteries.
Heart rate extremes: The monitor is unable to perform pressure measurements
at a heart rate of less than 15 bpm and greater than 300 bpm.
The NIBP measurement does not produce any waveform. Instead, it displays the
measurement result in the parameters area as shown below.

Alarm limit of the diastolic pressure. When the measured diastolic pressure value exceeds this
limit, the monitor generates alarms.
Alarm limit of the systolic pressure. When the measured systolic pressure value exceeds this
limit, the monitor generates alarms.
NIBP alarm off icon. When the alarms for systolic pressure, diastolic pressure and mean arterial
pressure are disabled, this icon is displayed, if one of them is enabled, this icon will disappear.
NIBP label. Select this label to access the NIBP menu.
NIBP unit: mmHg or kPa. Refer to REGION SETTINGS in CHAPTER 4 for
setting method.
Measured systolic pressure and diastolic pressure values. The left side of / is systolic
pressure value, while the right side is diastolic pressure value.
Measured mean arterial pressure value.
Information prompt bar. Different information is displayed on it for different situations.
Selecting the NIBP label pops up the following NIBP menu:
94
Alarm On/Off: Enables or disables the alarms for SYS, DIA and MAP simultaneously.
Alarms enabled: The NIBP alarm is turned on and the monitor alarms when the
measured NIBP value exceeds the preset alarm limit.
Alarms disabled: Icon is displayed on the left side of the NIBP label, the NIBP alarm is
turned off, and the monitor does not generate alarms when the measured NIBP
Alarm Setting: Select this button, the following Set Alarm Limits dialog box pops up.
The upper alarm limits, lower alarm limits, alarm switches and alarm printing switches for
SYS, DIA and MAP can be set in this dialog box. See ALARM SETTINGS in CHAPTER 5 for
Auto Manual: Switches between the auto and manual modes. In manual mode, word MANUAL
is displayed at position ; while in auto mode, word AUTO is displayed at positon with the
clock format time at position .
Test Interval: Selecting this button in auto mode accesses the following Set NIBP Auto Test
Interval dialog box.
In this dialog box, the NIBP automatic measurement interval time, which is set as 5 minutes in
default settings, can be set in the range from 2 minutes to 8 hours and displayed in the
information prompt bar.
Venous Puncture: Sets the venipuncture.
Stat Test: Selecting this button starts a continuous measurement for five minutes.
Inflate Pressure: Selecting this button in manual mode accesses the following dialog box.
The max cuff pressure can be set in this dialog. The default max cuff pressure is 165mmHg for
adult, 145mmHg for pediatric and 125mmHg for neonate.
FUNCTIONS
The NIBP monitoring has two functions, one is NIBP measurement, and the other is the
95
venipuncture function.
NIBP MEASUREMENT
When the NIBP measurement starts, the Monitor inflates the air into the cuff, and the SYS, DIA and
MAP are measured out via the sensor. A measurement process lasts about 40 seconds.
There are three NIBP measurement modes, one is manual mode, the other is auto mode, and the
third is continuous mode.
Manual mode
Select the Auto Manual button in the NIBP menu, if word MANUAL is displayed at the position ,
the manual mode is selected. In this mode, a NIBP measurement shall be started manually by
pressing the NIBP key on the front panel. Before manual NIBP measurement, the max cuff pressure
should be set to a proper value.
Auto mode
Select the Auto Manual button in the NIBP menu, if word AUTO is displayed at the position , the
auto mode is selected. In this mode, the monitor periodically starts the NIBP measurement
automatically at the preset time interval.
The auto mode has two statuses, one is the stay status. In this status, the clock at position stays,
and the auto measurement has not been started yet. The other status is the running status. In this
status, the clock at position runs, and the auto measurement has been started. The clock at
position indicates how much time still remains for the next measurement.
In the stay status, press the NIBP key to start the auto measurement. At this time, the clock at
position begins to run. Switching to the manual mode, then switching back to the auto mode can
stop the auto measurement. Pressing the NIBP key during the NIBP measurement can stop the
measurement and switch the running status to stay status.
Continuous mode
Selecting the Stat Test button in the NIBP menu starts a continuous measurement which is provided
for surgical or emergent patient. Its feature is that it continuously measures NIBP for five minutes
once it is started, and the measurement mode adopted is simpler than other modes. After five
minutes, the monitor restores to the status (auto or manual) before the continuous measurement.
NOTE
Whether in the auto or manual mode, pressing the NIBP key on the front panel will start
a NIBP measurement.
Pressing the NIBP key during the NIBP measurement stops the ongoing measurement and
deflates the cuff.
VENIPUNCTURE
Under the venipuncture mode, the monitor inflates the air into the cuff to a preset pressure, and
keeps the pressure during the preset time, then deflates.
Select the Venous Puncture button in the NIBP menu, the following dialog box pops up.
96

1 Venipuncture switch: Enables or disables the venipuncture.

Open: The venipuncture is turned on, the word VENOUS and the preset preasure are displayed
in the information prompt bar, shown as the figure below.
Close: The venipuncture is disabled.
2 Keeping pressure: The air inflating pressure.
3 Keeping time: From the air inflating time, until the air is deflated.
Patient type Pressure setting range Default pressure Maximum keeping time
Adult 20-120 mmHg 60 mmHg 170 s
Pediatric 20-80 mmHg 40 mmHg 170 s
Neonate 20-50 mmHg 30 mmHg 85 s
4 Select this key to confirm the setting.
Under the venipuncture mode, press the NIBP key to start and stop the air inflating.

Reusable blood pressure cuffs
The cuff is not suitable for dry-cleaned. Instead, it should be machine or hand
washed. Hand washing, may prolong the service life of the cuff. Before washing,
remove the latex rubber bladder. Allow the cuff to dry thoroughly after washing,
and then reinsert the rubber bladder. The cuff can be disinfected by means of
conventional autoclaving, gas, or radiation disinfection in hot air ovens, or
sterilized by immersion in decontamination solutions. Remember to remove the
rubber bladder if you use this method.
To replace the rubber bladder in the cuff:

1. Place the bladder on top of the cuff so the rubber tubes line up with the
97
large opening on the long side of the cuff.
2. Roll the bladder lengthwise and insert it into the opening on the long side of
the cuff.
3. Hold the tubes and the cuff and shake the complete cuff until the bladder is
in position.
4. Thread the rubber tubes from inside the cuff, and out through the small
hole under the internal flap.
Disposable blood pressure cuffs
Disposable cuffs are intended for single patient use only. Do not sterilize or use
autoclave sterilization for disposable cuffs. But they can be washed with a mild soap and
water solution to control the infection.
NOTE
Disposable blood pressure cuffs must be recycled or disposed of properly, complying with
the local laws.
WARNING
Do not press or limit the rubber tube on the cuff.
Do not allow the water or detergent liquid get inside the NIBP connection, otherwise the
monitor may be damaged.
When a reusable cuff is not connected to the monitor or is being cleaned, avoid splashing
liquid into the rubber tube or the monitor inadvertently.
When cleaning the Monitor, only clean the connector external part, and do not clean its
internal part.
TROUBLE SHOOTING
The NIBP current status is displayed at the positon , please adopt the following disposals if the
messages shown as below appear.
Problems Possible reasons Suggestions and way out

Startup Fail Monitor hardware error Stop the NIBP measurement, and inform the
qualified maintenance personnel specified by
the supplier to repair.
No Cuff The cuff is not properly tied Tie up the cuff
up or no cuff
Cuff Leak The cuff, rubber tube or Check and replace the air leakage part, if
connector is damaged necessary, inform the qualified maintenance
personnel specified by the supplier to repair.
Pulse too weak The cuff is too loose or the Use other method to measure the NIBP.
patients pulse is too weak.
Over Pressure The pressure exceeds the Remeasure it, if the failure continues, stop the
specified safety upper limit NIBP measurement, and inform the qualified
98
maintenance personnel specified by the
supplier to repair.
NIBP Compensate
1. Press the menu key and enter the system setup item
2. Press the system setup menu key and enter the maintenance setup
item
3. Press the function maintenance menu key and enter the Reserved 1
4. Input the password 1231 and enter the function compensate menu item ,you will do
it for Temperature NIBP and SPO2
The service man compensate the function such as Temperature NIBP and
SPO2,and so on. according to the monitoring the parameter result so as to
measuring the real result,the other function parameter is the same as to the
NIBP
The NIBP compensate range is from 75% to 125% which is some times than
measuring data.The detailed compensate windows of SYS\DIA\Map as follows:
99
100
CHAPTER 16:
TEMP MONITORING
TEMPERATURE PROBE INSTALLATION

The monitor is able to use two temperature probes simultaneously. Attach the temperature probe to
the patients body where ought to be measured, to abtain two temperature values and the difference
between them.
If a disposable temperature probe is used, plug the temperature probe cable in
the temperature probe connector, and then connect the temperature probe with
the cable; if a reusable temperature probe is used, connect the temperature
probe with the temperature probe connector directly.
NOTE
The disposable temperature probe is for single patient use only.
WARNING
Be careful to avoid damaging the temperature probe and cable. When the temperature
probe and cable are not in use, shape them into a loose round. If the cable is tangled too
tightly or over-bent, mechanical damage may occur.
The calibration of the temperature measurement function is desired every year (or as
dictated by your Hospital Procedures Policy). If you need to calibrate the temperature
measurement function, contact the manufacturer.
TEMP PARAMETER
The temperature measurement result is displayed in the parameters area, as shown in the figure
below:

1 Temperature lower alarm limit. When the measured temperature value is less than it, the
101
monitor generates alams.
2 Temperature upper alarm limit. When the measured temperature value is greater than it, the
monitor generates alams.
3 Temperature alarm off icon. When the temperature alarm is disabled, it is displayed.
4 Temperature label: Select this label, and the menu shown as below pops up.
5 Temperature unit: or . See REGION SETTINGS in CHAPTER 4 for the setting method.
6 Temperature difference: It is the absolute value of the difference between the temperature
values of two channels.
7 Measured temperature value of channel 1: Measurement range: (25.0-45.0).
8 Measured temperature value of channel 2: Measurement range: (25.0-45.0).
TEMP MENU
Selecting the temperature label in the parameters area pops up the following menu.
Alarm On/Off: Enables or disables the TEMP alarm.

Alarms enabled: The TEMP alarm is turned on and the monitor alarms when the
measured TEMP value exceeds the preset alarm limit.
Alarms disabled: Icon is displayed on the left side of the TEMP label, the TEMP alarm is
turned off, and the monitor does not generate alarms when the measured TEMP
Alarm Setting: Select this button, and the following Set Alarm Limits dialog box pops up.
The upper alarm limit, lower alarm limit, alarm switch and alarm printing switch of TEMP can
be set in this dialog box. See ALARM SETTINGS in CHAPTER 5 for detailed information.
The temperature difference has no alarm function.
Mode: Select this button, the TEMP display mode switches among three modes. One is
displaying the temperatures of two channels and the temperature difference, another is
displaying the temperatures of two channels, and the third is displaying the temeperature of
channel 1 and the temperature difference. The mode can be selected according to the
requirement, shown as below.
102
WARNING
Before cleaning the monitor or the probe, make sure the monitor is turned off and
disconnected from AC power.
Reusable temperature probes

The temperature probe should not be heated to a temperature over 100
(212). It is only able to bear the temperature between 80 and 100 (176
to 212) for a short time.
The probe must not be disinfected in steam.
Only detergents containing alcohol can be used for disinfection.
The rectal probes should be used, if possible, in conjunction with a protective
rubber cover.
To clean the probe, hold the tip with one hand and with the other hand rub
the probe down in the direction of the connector using a moist lint-free
cloth.
NOTE
Disposable temperature probes must not be re-sterilized or reused.
Disposable temperature probes must be recycled or disposed of properly, complying with
the local laws.
Temperature Compensate
During the monitoring the patient Temperature parameter,you will compensate the
temperature if you find that the temperature departure some range of the real result as
follows:
1.Press the menu key and enter the system setup item
103
2.Press the system setup menu key and enter the maintenance setup
item
3.Press the function maintenance menu key and enter the Reserved 1
4.Input the password 1231 and enter the function compensate menu item ,you will do it
for Temperature NIBP and SPO2
Temperature compensate range is from +1.5 to -1.5,Both T1 channel

and T2 channel compensate windows as follows:
104
CHAPTER 17:
SpO2 MONITORING
OVERVIEW
SpO2 measurement is based on two principles: Firstly, oxyhemoglobin and
deoxyhemoglobin differ in their absorption of red and infrared light. Secondly,
the volume of arterial blood in tissue changes during the pulse. A monitor
determines SpO2 (oxygen saturation) by passing red and infrared light into an
arteriolar bed and measuring changes in light absorption during the pulsatile
cycle. Red and infrared low-voltage light-emitting diodes (LEDs) in the sensor
serve as light sources, a photodiode serves as the photo detector.
Because oxyhemoglobin and deoxyhemoglobin differ in light absorption, the
amount of red and infrared light absorbed by blood is related to hemoglobin
oxygen saturation. To identify the oxygen saturation of arterial hemoglobin, the
monitor uses the pulsatile nature of arterial flow. During systole, a new pulse of
arterial blood enters the vascular bed, and the blood volume and light
absorption increase. During diastole, the blood volume and light absorption
reach their lowest point. The monitor bases its SpO 2 measurements on the
difference between maximum and minimum absorption (i.e., measurements at
systole and diastole). By doing so, it focuses on light absorption by pulsatile
arterial blood, eliminating the effects of nonpulsatile absorbers such as tissue,
bone, and venous blood.
The monitor determines SpO2 and pulse rate by passing two wavelengths of light, one red and one
infrared, through body tissue to a photodetector. During measurement, the signal strength resulting
from each light source depends on the color and thickness of the body tissue, the probe placement,
105
RED LED AND INFRARED LED

LIGHT SOURCES
the intensity of the light sources, and the absorption of the arterial and venous blood (including the
time varying effects of the pulse) in the body tissue (Refer to Figure 17-1).

MONITOR

9 6 % S p O 2
72 PULSE
PERFUSION

INDICATOR
DETECTOR
FIGURE 17-1 SpO2

8 THETORY
S p O 2 OF
OPERATION

The monitor processes these signals, separating the time invariant parameters (tissue thickness, skin
color, light intensity, and venous blood) from the time variant parameters (arterial volume and
SpO2) to identify the pulse rate and calculate oxygen saturation. Oxygen saturation calculations
can be performed because oxygen saturated blood predictably absorbs less red light than oxygen
depleted blood.
The monitor can be used under low perfusion with same accuracy as normal
condition.
The monitor measures the patients SpO2 and displays:

Pulse rate (PR) value in the parameters area.
PLETH waveform and pulse intensity (perfusion indicator) in the channels
area.
Oxygen saturation (SpO2 %) value in the parameters area.
As the following figure shows, the perfusion indicator (prorate with the pulse
intensity) is located on the left side of the PLETH waveform while the measured
SpO2 value on the right. The SpO2 value is displayed by percentage. Besides, the
SpO2 label in the parameters area allows you to access the SpO2 menu.
Perfusion indicator PLETH waveform SpO2 alarm limit SpO2 label SpO2 value
The PR value is displayed in the parameters area only if:

1. SpO2 is selected in the HR Source menu; or
2. Auto is selected in the HR Source menu and the received ECG signal is bad.
PRECAUTIONS
WARNING
The monitor can overestimate the SpO2 value in the presence of Hb-CO, Met-Hb or dye
106
dilution chemicals.
ES (Electrosurgery) equipment wire and SpO2 cable must not be tangled up. Carefully
route patient cabling to reduce the possibility of patient entanglement or strangulation.
Do not use this instrument and the sensors during magnetic resonance imaging (MRI).
Induced current could potentially cause burns. The monitor may affect the MRI image,
and the MRI unit may affect the accuracy of the oximetry measurements.
Do not put the SpO2 sensor on the limb with arterial catheter or venous syringe.
Do not perform SpO2 monitoring and NIBP measurements on the same arm
simultaneously. Obstruction of blood flow during NIBP measurements may adversely
affect the reading of the SpO2 value.
Before performing the testing, check the sensor cable. After unplugging the SpO2 sensor
cable from the socket, the system shall display the flashing prompt information "Sensor
Off" above the PLETH waveform.
Prolonged and continuous monitoring may increase the risk of burns at the site of the
sensor. It is especially important to check the sensor placement, and ensure proper
attachment on neonates and patients of poor perfusion or skin sensitive to light. Check the
sensor location every 23 hours and move to another location if the skin deteriorates.
More frequent examinations may be required for different patients.
NOTE
Place the SpO2 sensor cable at the backside of the patient hand. Make sure the fingernail
is just opposite to the light emitted from the sensor.
Follow the procedure as below:
2. Attach the sensor to the proper site on the patient.
3. Plug the connector of the sensor extension cable into the SpO2 connector on
monitor.
The process of SpO2 plethysmogram measurement is generally the same. But
the SpO2 sensor selection and placement depend on the patient type. When
choosing a site for a sensor, refer to the directions for that sensor.
MEASUREMENT LIMITATIONS
If the accuracy of any measurement does not seem reasonable, first check the
patients vital signs by an alternate method. Then check the instrument for
proper function. Inaccurate measurements may be caused by:
Incorrect sensor application or use;
Placement of a sensor on the same extremity with a blood pressure cuff,
arterial catheter, or intravascular line;

Exposure to excessive illumination, such as surgical lamps (especially ones
with a xenon light source), bilirubin lamps, fluorescent lights, infrared

heating lamps, or direct sunlight (exposure to excessive illumination can be
107
corrected by covering the sensor with a dark material);
Excessive patient motion;
Venous pulsations;
Intravascular dyes such as indocyanine green or methylene blue;
Defibrillation;
Other physiological conditions or medical procedures that may interfere with

the monitors measurements include significant levels of dysfunctional
hemoglobin, low perfusion, and dark pigment.
Loss of pulse signal can occur in the following situations:
The sensor is too tight;
A blood pressure cuff is inflated on the same extremity as the one with a
SpO2 sensor attached;

There is arterial occlusion proximal to the sensor.
Select an appropriate sensor, apply it as directed, and observe all warnings and
cautions presented in the directions for use accompanying the sensor. Clean
and remove any substances such as nail polish from the application site.
Periodically check to ensure that the sensor remains properly positioned on the
patient.
If patient movement presents a problem, try one or more of the following
remedies to correct the problem.
Verify that the sensor is properly and securely applied.
Move the sensor to a less active site.
MENU
SpO2 MENU
Selecting the SpO2 label in the parameters area pops up the following menu:
Alarm On/Off: Enables or disables the SpO2 alarm.

Alarms enabled: The SpO2 alarm is turned on and the monitor alarms when the
measured SpO2 value exceeds the preset alarm limit.
Alarms disabled: Icon is displayed on the left side of the SpO2 label, the SpO2 alarm is
turned off, and the monitor does not generate alarms when the measured SpO2
Alarm Setting: Selecting this button pops up the following Set Alarm Limits dialog box.
The upper alarm limit, lower alarm limit, alarm switch and alarm printing switch of SpO2 can
be set in this dialog box. See ALARM SETTINGS in CHAPTER 5 for detailed information.
AVRG.: Select this button, the following menu pops up:
108
The average period for SpO2 calculation can be set in this menu.
5. 4 Beats: The average period is 4 SpO2 periods.
WARNING
Setting the SpO2 upper alarm limit to 100% will disable the upper alarm limit. High
oxygen levels may predispose a premature infant to retrolental fibroplasia. Therefore, the
upper alarm limit for oxygen saturation must be carefully selected in accordance with the
commonly accepted clinical practices.
PLETH MENU
Selecting the PLETH channel label pops up the following menu:
Fill Waveform: Fills or unfills the PLETH waveform. It has the same function as the Pleth Fill
button in the Display menu.
NOTE
Clean the sensor and the surface of the probe before and after each use. You can wipe
surfaces with 70% Isopropylic Alcohol or soak the clip for five minutes in Isopropylic
alcohol. After soaking the clip, it must be rinsed with water and air-dried prior its use.
SpO2 sensor must be recycled or disposed of properly, complying with the local laws.
Spo2 compensate
During the monitoring the patient Temperature parameter,you will compensate the
temperature if you find that the temperature departure some range of the real result as follows:
The spo2 compensate range is from 30% to +30%,the detailed windows as

follows:
1.Press the menu key and enter the system setup item
2.Press the system setup menu key and enter the maintenance setup
109
item
3.Press the function maintenance menu key and enter the Reserved 1
4.Input the password 1231 and enter the function compensate menu item ,you will do it
for Temperature NIBP and SPO2
CHAPTER 18: IBP

MONITORING
IBP CHANNELS
The monitor provides two channels to measure the invasive blood pressure (IBP, including systolic,
diastolic and mean pressures), and displays two channels of waveforms and two parameters. The two
channels of waveforms are displayed in a same or different waveform area, differentiated by color.
When the two curves overlapped, the curve color will be the color of channel 2. The figure below is
the channels displayed in different waveform area:
110

Label of channel 1: Selecting this label pops up the menu of channel 1.

Label of channel 2: Selecting this label pops up the menu of channel 2.
Pressure axis: It is the pressure axis of the waveform displayed on its right side, shown as
below:
Maximum
0 mmHg
The bottom horizontal line indicates the location of zero pressure. If a curve dot is displayed higher
than this line, it means the pressure of this dot is positive; accordingly, the pressure of the dot, which
is lower than this line, is negative.
The top horizontal line indicates the maximum pressure of current display gain. The curve line
where its pressure is higher than the maximum pressure will be clipped and becomes a section of
horizontal line.
The height of the waveforms relates to the pressure. And the ratio between height and pressure is
specified. Maximum value and Minimum value are listed in the following table:
Maximum value on screen Minimum value on screen

6 mmHg -1 mmHg
10 mmHg -1 mmHg
18 mmHg -2 mmHg
30 mmHg -3 mmHg
60mmHg -6mmHg
80mmHg -8mmHg
100mmHg -11mmHg
120mmHg -13mmHg
180mmHg -20mmHg
240mmHg -26mmHg
300mmHg -33mmHg
The monitor can automatically select a proper ratio according to the phase of the waveform. It also
provides a function to adjust the ratio manually. Here we call it two gain modes: Auto mode and
Manual mode.
Status message: Displayed above the waveform. All the possible status messages are listed in
the following table:
111
Message string Meaning Possible causation
No Response The monitor can not get data When the monitor is restarting, this
from this channel message indicates that the channel has
not been started yet, but this message
will disappear in 5 seconds.
Or the hardware of IBP module does not
work properly and needs to be fixed.
Sensor Off The pressure sensor isnt The pressure sensor cable has fallen off
connectted to the monitor. from the monitor or from the pressure
sensor.
NOT Zero The channel wasnt zeroed Operator has to zero the monitor after it
is started. If not, the measured pressure
is unusable.
Auto/Manual This is a normal working The channel works properly.
message. It tells the current
gain mode and gain ratio.
Waveform of channel 1.
Waveform of channel 2.
IBP PARAMETER
The measured IBP values of two channels are displayed in the parameters area, the right side of the
IBP channels, shown as below:

IBP label of channel 1

Systolic blood pressure (SYS)
Mean pressure (MEAN)
Indicates that this area displays the measured IBP values of channel 1.
Diastolic blood pressure (DIA)
IBP values can vary in the range from 60mmHg to 300mmHg. Values not in this range will be
displayed as invalid pressure, in the form of --- or --.-.
But there are more reasons if these pressure values are displayed as invalid values, they are:
1. The actual pressure is not in the range from -60 mmHg to 300 mmHg.
2. The channel wasnt zeroed.
3. The cable is disconnected or not connected firmly.
4. The channel is not calibrated properly.
5. In zero processing.
6. Monitor is starting.
The IBP unit is the same as the NIBP unit. See REGION SETTINGS in CHAPTER 4 for detailed
information.
112
PRECAUTIONS
WARNING
Use only the IBP transducer specified in this manual. Disposable IBP transducers should
not be reused.
Parts and accessories used must meet the safety requirements of the medical electrical
equipment standards.
Avoid conductive connection to the applied part likely to degrade safety.
When the monitor is used with high frequency surgical equipment, do not allow the
transducer and the cable contact the high frequency surgical equipment to prevent the
patient from burning caused by leakage current.
1. Plug the pressure cable into the IBP connector on the monitor and power on
the monitor.
2. Prepare the pressure line and transducer by flushing the system with normal
saline solution. Make sure the tubing and transducer system is free of air
bubbles.
NOTE
In case of any entrapped air in the pressure system, re-fill the system with normal saline.
3. Connect the catheter to the pressure line, making sure there is no air
present in the catheter or pressure line.
4. Position the transducer so it is at the same level with the patients heart,
approximately mid-axillary line.
5. Verify the correct label is selected.
6. Zero the transducer.
Normal salin
with heparin Pressure
transducer
Drip chamber
Monitor
3-way
stopcock
Pressure line
Pessure transducer cable
IBP MENU
IBP PARAMETER MENU
Select the IBP parameter label in the parameters area, the following menu pops up:
113
Alarm On/Off: Enables or disables the IBP alarm (including the systolic, diastolic and mean
pressure alarms).
Alarm enabled: The IBP alarm is turned on, the monitor alarms when the measured IBP
Alarm disabled: Icon is displayed on the left side of the IBP parameter label, the IBP alarm
is turned off, and the monitor does not generate alarms when the measured
IBP value exceeds the preset alarm limit.
The upper alarm limits, lower alarm limits, alarm switches and alarm printing switches of SYS,
DIA and MEAN can be set in this dialog box. See ALARM SETTINGS in CHAPTER 5 for
Label: Selecting this botton switches the label of this channel. The label recycles in the order
listed below:
Label Definition
ART Arterial Blood Pressure
CVP Center Venous Pressure
RVP Right Ventricle Pressure
LAP Left Atria Pressure
RAP Right Atria Pressure
PAP Pulmonary Arterial Pressure
ICP Intracranial Pressure
LVP Left Ventricle Pressure
The selected label will be saved in 5 seconds and displayed in the corresponding channel. It
does not take any other effect other than displaying.
IBP CHANNEL MENU

Select the label of a target IBP channel, and the menu of this channel pops up, shown as below. In
this menu, we can change the label of the channel, zero the transducer and select the display gain.
Label
It has the same function as the Label button in the IBP parameter menu. Selecting this button
switches the label of this channel.
Zero
In the first time we select this button, the corresponding channel will perform zero process. And
selecting this button again will terminate the zeroing. The system will treat the detected absolute
pressure value as the relative zero point. This zero point affects both the pressure values and the
114
waveforms of the channel.
Zeroing procedure:
1. Disconnect the transducer from the patient.
2. Adjust the 3-way stopcock to close the channel leading to the patient. The
transducer is open to the atmosphere through the stopcock.
3. Select the Zero button in the IBP channel menu to start zeroing.
NOTE
The zeroing funciton is noneffective in sensor off status, it is effective only when the sensor
is connected to the monitor.
Position the transducer at the same level with the patients heart, approximately mid-
axillary line.
Perform the pressure zeroing when the monitor is powered on and at measuring intervals
(at least once per day). The zeroing should also be conducted once the transducer cable or
catheter is changed.
Ensure the catheter is static. In the catheter static status, the zeroing will be completed
soon.
Gain Mode
This button is to select the display gain mode for the channel. The gain mode switches between Auto
and Manual when selecting this button. This function is disabled if the channel wasnt zeroed.
Adjust Gain
If the gain mode of the channel is Manual, we can use this button to increase/decrease display gain.
The clockwise for decrease, whereas for increase. This operation zooms in the waveform in vertical
direction. This function is also disabled if the channel wasnt zeroed.
WARNING
Before cleaning the transducer, make sure the transducer is disconnected from the
monitor, or the monitor is powered off and disconnected from AC power.
CLEANING OF IBP TRANSDUCER

After the IBP monitoring operation is completed, remove the tubing and the
dome from the transducer and wipe the transducer diaphragm with water. To
clean the transducer and the cable, wipe them using soap or the detergents
listed below:
Cetylcide
Wavicide-01
Wescodyne
Cidex
Lysol
Vesphene
Do not immerse the connector in any liquid. After cleaning, dry the transducer
thoroughly before storing. Slight discoloration or temporary increase of surface
115
stickiness of the cable should not be considered abnormal. If it is necessary to
remove the adhesive tape residue from the transducer cable, the double seal
tape remover is recommended; use the remover with special caution to
minimize the damage to the cable. Acetone, Alcohol, Ammonia and Chloroform,
or other strong solvents are not recommended because they are harmful to the
vinyl cabling if used for a long time.
NOTE
The disposable transducers or domes must not be reused.
To avoid contamination, the disposable transducers or domes must be reclaimed or
disposed of properly, complying with the local laws.
STERILIZATION
Chemical Solution Sterilization
After finishing the cleaning, select an effective sterilant for chemical solution
sterilization of the operating room equipment. Buffered glutaraldehyde (e.g.
Cidex or Hospisept) is recommended. Do not use quaternary cationic detergents
such as zephiran chloride. If the whole unit is to be sterilized, immerse the
transducer but not the electrical connector into the sterilant for the
recommended sterilizing period. Ensure that the dome has been removed. Then
rinse all transducer parts except the electrical connector with sterilized water or
saline. The transducer must be thoroughly dried before storing.
Gas Sterilization
For more complete asepsis, use gas sterilization. The transducer should be
completely dry after cleaning. When ethylene oxide gas is used as the gas
disinfectant, follow the operating instructions provided by the manufacturer of
the gas disinfectant.
NOTE
The disinfectant temperature must not exceed 70C (158F). Plastics in the pressure
transducer may deform or melt above this temperature.
116
CHAPTER 19:
CO2 MONITORING
INTRODUCTION
CO2 monitoring is to monitor the respiration of patient by detecting the concentration of CO 2
generated during respiration. The maximum concentration of CO2 at the end of exhalation is called
End-Tidal CO2 (EtCO2). The minimum concentration of CO2 at the end of inspiration is called
Fractional Inspiratory CO2 (FiCO2). CO2 is generated by cells in the body during metabolizing, and
is breathed out via breath system. The concentration of CO2 breathed out from lung reflects directly
the situation of metabolizing and breathe system. If the concentration of CO 2 is high, it means that
metabolizing is excited, such as blood poisoning or acute fever. If the concentration of CO2 is low, it
is commonly because the output ability of heart is weak, or the heart stop beating, or the lung soak
for the flux of blood is low or oxygen it carried is not enough. Monitoring CO2 is used to warn the
doctor of the abnormal of breathe and metabolizing for hocused patient.
The concentration of CO2 is represented as a pressure level, with mmHg, kPa or % as its unit.
Generally, the acceptable value is 38mmHg (5.1kPa or 5%) when air pressure is 760mmHg. The
concentration of CO2 varies very fast from 0% to 5% normally. To detect the concentration of CO2
accurately, the monitor has to be very sensitive.
Follow the procedure specified below to monitor the CO2.
1. Plug the dehydration vase into its receptacle, then push its bottom carefully to its position,
shown as the figure below:
Water trap receptacle
Sampling line
Water trap
2. Connect one end of the sampling line to the dehydration vase.

3. Connect the other end of the sampling line to the patient.
5. Enables the displaying of CO2 channel via the Format Setup button in the Display menu.
6. Select the Start Pump button in the CO2 channel menu to start air pump.
7. The CO2 monitoring starts.
117
NOTE
To monitor the CO2, the CO2 channel and the air pump must be enabled. If the monitor is
in default settings, these two items must be reset.
When there is no CO2 monitoring, disables the CO2 channel or air pump to prolong its
service life.
The CO2 monitoring displays a CO2 waveform in the channels area and the measured EtCO2 and
FiCO2 values in the parameters area.
CO2 CHANNEL
The CO2 channel is displayed as below:

CO2 channel label concentration unit gain mode gain

Prompt information flow rate scale CO2 waveform
Selecting the CO2 channel label pops up the following menu:
Gain Mode: Select this button, the gain mode of the CO 2 waveform switches between AUTO
and MANUAL modes.
Adjust Gain: This button is only available in MANUAL mode. Select this button then turn the
rotating mouse to adjust the gain. Five grades are available: 1/2, 1, 2, 4 and 8. Press
the mouse to exit the gain adjustment status when the gain has been chosen, and the CO2
waveform will be displayed in chosen gain.
Flow Rate: Select this button to adjust the flow rate of the CO2. Three grades are available:
65cc/min, 100cc/min and 150cc/min.
25mm/s and 50mm/s. It is the same as the RESP waveform speed, and switches it will swithes
the other one simultaneously. The current CO2 waveform speed can be viewed in the prompt
information bar of the RESP channel.
Concent. Unit: Select this button, and the concentration unit switches among mmHg, kPa and %.
Start Pump: Starts or stops the air pump. If the air pump is disabled, this button is displayed as
Start Pump, select it to start the air pump; if the air pump is enabled, this button is displayed as
Stop Pump, select it to stop the air pump.
118
CO2 PARAMETER
The measured CO2 values are displayed as below:

1 Upper alarm limit of EtCO2.

2 Lower alarm limit of EtCO2.
3 Measured EtCO2 value.
4 Measured FiCO2 value.
5 Label of EtCO2.
Selecting the EtCO2 label pops up the following menu:
Alarm On/Off: Enables or disables the CO2 (EtCO2 and FiCO2) alarm.
Alarm enabled: The CO2 alarm is turned on, the monitor alarms when the measured
EtCO2 or FiCO2 value exceeds the preset alarm limit.
Alarm disabled: Icon is displayed on the left side of the EtCO2 label, the CO2 alarm is turned
off, and the monitor does not generate alarms when the measured EtCO2 or
FiCO2 value exceeds the preset alarm limit.
The upper alarm limits, lower alarm limits, alarm switches and alarm printing switches of
EtCO2 and FiCO2 can be set in this dialog box. See ALARM SETTINGS in CHAPTER 5 for
Concent. Unit: Select this button, the concentration unit switches among mmHg, kPa and %.
119
In case of an exception in the sampling system of the CO2 module, check for
entanglement of the sampling line. If the sampling line is not entangled, remove
the dehydration vase. In this situation, if the dehydration vase is not blocked,
the sampling line must have been blocked, and you must replace it with a new
one. If the dehydration vase has been blocked, you should replace it with a new
dehydration vase.
WARNING
The sampling line is disposable, must not re-sterilize or reuse it.
Do not press or limit the sampling line.
The dehydration vase is used to collect water drops condensed in the sampling airway and
prevent water drops from entering the module. When the collected water reaches to a
certain amount, remove the water to avoid blocking the airway.
In the long-term use, dust or other substances may lower the air permeability of the filter
material in the dehydration vase and may block the airway. In this situation, the
dehydration vase must be replaced.
NOTE
The sampling line must be recycled or disposed of properly, complying with the local laws.
120
CHAPTER 20:
MAINTENANCE
WARNING
The safety inspection or maintenance, which requires opening the monitor housing, must
be performed by trained and authorized personnel only. Otherwise, equipment failure
and possible health hazard may be caused.
INSPECTION
Make sure the qualified service personnel have implemented a complete
inspection before putting the monitor into operation, after monitor servicing or
system upgrading, or after the monitor has been used for 6-12 consecutive
months. This is to ensure the normal operation of the system.
Follow these guidelines when inspecting the equipment:
The environment and the power supply meet the specified requirements.
Inspect the keys, control knob, connectors and accessories for damage.
Inspect the power cords for fraying or other damage and check the insulation.
The grounding cables are correctly connected.
Only specified accessories like electrodes, sensors and probes are applied.
The monitor clock is correct.
The audible and visual alarms functions normally.
The printer functions normally and the printer paper meets the requirement.
In case of any damage or exception, do not use the monitor. Contact the
technician in your hospital or our Customer Service immediately.
CLEANING
WARNING
Be sure to shut down the system and disconnect all power cords from the outlet before
cleaning the equipment.
Your equipment should be cleaned on a regular basis. If there is heavy pollution

or lots of dust and sand in your place, the equipment should be cleaned more
frequently. Before cleaning the equipment, consult your hospitals regulations
for cleaning, disinfecting and sterilizing equipment.
The exterior surfaces of the equipment may be cleaned with a clean and soft
cloth, sponge or cotton ball, dampened with a non-erosive cleaning solution.
Drying off excess cleaning solution before cleaning the equipment is
recommended. Following are examples of cleaning solutions:
121
Diluted soap water
Diluted ammonia water
Diluted sodium hyoichlo (bleaching agent)
Diluted formaldehyde (35 to 37%)
Hydrogen peroxide (3%)
Ethanol (70%), or Isopropanol (70%)
To avoid damage to the equipment, follow these rules:

ALWAYS dilute the solutions according to the manufacturers suggestions.
ALWAYS wipe off all the cleaning solution with a dry cloth after cleaning.
NEVER submerge the equipment into water or any cleaning solution, or pour
or spray water or any cleaning solution on the equipment.

NEVER permit fluids run into the casing, switches, connectors, or any
ventilation openings in the equipment.

NEVER use abrasive, erosive cleaners, or cleaners containing acetone.
Failure to follow these rules may erode or fray the casing, or blur lettering on
the labels, or cause equipment failures.
For cleaning information of accessories, please refer to the chapters for specific
patient parameters and the instructions for use of the accessories.
DISINFECTION AND STERILIZATION

Sterilization or disinfection may cause damage to the equipment. We
recommend the sterilization and disinfection are contained in the hospitals
servicing schedule only when necessary. The equipment should be cleaned prior
to sterilization and disinfection.
Recommended sterilization material: Alcohol based (Ethanol 70%, Isopropanol
70%), and aldehyde based.
WARNING
Disinfection or sterilization may cause damage to the equipment; therefore, when
preparing to disinfect or sterilize the equipment, consult your hospitals infection
controllers or professionals.
The cleaning solutions above can only be used for general cleaning. If you use them to
control infections, we shall assume no responsible for the effectiveness.
NOTE
ALWAYS dilute the solutions according to the manufacturers suggestions and adopt
lower concentration if possible.
NEVER submerge the equipment into water or any solution, or pour water or any
solution on the equipment.
ALWAYS wipe off all the excess liquids on the equipment surface and accessory surface
with a dry cloth.
Never use EtO and formaldehyde to disinfect.
122
Never permit high-pressure and high-temperature disinfection of the equipment and
accessories.
CHAPTER 21:
LABELS, PACKAGING, TRANSPORT AND STORING
LABELS
PRODUCT LABELS
G3C label
G3D label
G3F label
G3G label
123
PACKAGING LABELS
There are four symbols on the packing case. Their meanings are shown as below:
Upward
Fragile, handle with care
Keep dry
Stacked not more than four layers
PACKAGING
The monitor is sealed in a plastic bag and then put in the packing case that is filled with sponge or
foam.
TRANSPORT
The monitor can be transported by the aircraft, train or automobile. It has to prevent from strong
collision and being placed with corrosive substance.
STORING
The packed monitor should be stored in the temperature from -20 to +50, relative humidity
not greater than 85%, non-corrosive gas and well-ventilated room.
124
Introduction on the inside module structure and each function module
Basal inside system composition

The monitor is composed by the multi-function module (ECG, BP SPO2, TEMP, and
RESP), operation keyboard, driver Port, network Port ,Intelligent power, AC/DC power,
the Central Monitor system, TFT display, and correlative as follows:
Operating
keyboard
Printing
Port GAA230/134/126
ARM main board multi -function board
Network
Port
Display Intelligent power baoard
AC/DC AC power input

Accumulator
Introductions about the main module function.
1 Intelligent power board
The intelligent power board acts as automatic transforming voltage from the 15v to 12v
and 5v and so on. on the other hand, it also manages the battery automatic charge-
discharge and the overload protection
2 Operation keyboard
Operation keyboard carries out three parts function as follows:
1. Mouse function,similarly to the PC mouse by turning the rotator and let the cursor place
some position and then click it to enter the corresponding menu.
2. Execute the measurement of every function parameter by pressing the the corresponding
key
3. Provide current pulse to speakerlouder and let it make sound
3 ARM main board
It perform some parts function as follows:

1. To communicate and the function board e.g.GAA134,GAA230 etc. and LCD or LED and so on
afer downloaded the Linux program
2. To connect the central system by the internet port on it with the net cable
3.To connect printer and perform the printing work.
125
4 GAA230GAA134 multi-function module
To implement the function of collection, enlarging, controlling, and switching all kinds of
function parameters e.g ECG, TEMP, BP, RESP, and SPO2 and so on.
Troubleshooting
G3 monitor trouble, reason and action

Problem Reason Action
No signal on 1. The outside receptacle is not 1. Check the connection of
display and no connected well power or change
power light when 2. The fuse inside the monitor is 2. Change the fuse or power
turning on the bad, or the power is bad
Monitor 3. Thhe intelligent power board 3. Change the intelligent
has some problem power board or repair it
4. AC/DC power doesnt work 4. Repair it or change it if it
normally wont be repaired to be good
No signal on the 1. The inverter and 12v power is 1. Check inverter connection
led display but connected incorrectly
power indication 2.The inverter doesnt work 2. Repair the inverter or
led is light when normally or has some problem change it
turning on the 3. LED doesnt work normally or 3. Change LED
Monitor has some problem
No signal on led 1.There isnt 5v output in the 1.Change intelligent power
display intelligent power board board
2.The ARM main board displays 2.Repair the main board or
unsuccessfully change it with one OK one
3.The cable of display is not 3. Replace the display cable
very tight with the display socket
3. LED doesnt work normally or 4. Change LED
has some problem
ECG signal noise 1.The ECG electrode is used for 1. Change with a new ECG
level is bigger long time or over the warranty electrode
than the standard period
value or appears 2.The ECG electrode is not 2. Place the ECG electrode
leading off on the placed correctly according to operation manual
display screen 3. ECG cable itself has quality 3. Change another ECG cable
problem
4. GAA134 module doesnt work 4. Repair the GAA134 board
normally or change another one that
the function is good.
No ECG Both GAA230 and GAA134 Repair them or change
waveform and function board dont work another one that the function
126
pump doesnt normally is good.
work
The blood 1.The cuff and tube are 1.Check or change the cuff or
pressure value is barraged or air leaks tube
not correct 2.The NIBP cuff is disturbed2.Keep the patient calm so as
during the measuring process to outside interfering
3. The NIBP cuff position isnt
3.Place the NIBP cuff the
correct correct position according to
the operation manual
4. The GAA230 board doesnt 4.Repair the GAA230 board or
work normally change it if it cant be repaired
to be good
5.The valve leaks 5. Change the valve
The SPO2 probe 1. The SPO2 probe itself has 1.Repair the spo2 probe or
led isnt glow and quality problem change it
there is no 2. The SPO2 board has some 2.Repair the spo2 board or
waveform and problem change it
valu or the
measuring value
isnt correct
3. There is strong light around 2.Cover the probe(for example

The blood the spo2 probe with towel)
pressure value is 3.The blood circulation by 3.Help patient recover blood
not correct nipped by spo2 probe nail is circulation
blocked
1.The cuff and tube are 1.Check or change the cuff or
barraged or air leaks tube
2.The NIBP cuff is disturbed 2.Keep the patient calm so as
during the measuring process to outside interfering
3. The NIBP cuff position isnt 3.Place the NIBP cuff the
correct correct position according to
the operation manual
RESP rate is not 1.ECG electrode is placed
correct incorrectly 1.Place the ECG electrode
correctly
2.GAA134 doesnt work 2. Repair the GAA134 OR
normally change it if it can't be repaired
to be good
No sound 1.The loudspeaker is connected 1.Reconnect the loudspeaker
incorrectly power cable
2. The keyboard has some 2. Repair the keyboard or
mistake change it if it cant be repaired
to be good
127
Electric draw
ECG PART
IRESP PART
128
NIBP PART
SPO2 PART
129
TEMP PART
TRESP PART
130
BOM of Function module
S.N. Mark QTY. Item Main-Sub Specification Part number

material
1 C807,C808,C809 3 SMT Porcelain Main material 10pF,50V,10%,0603,X7R 12110021
capacitor
2 C7,C8,C805,C806,C811,C812 6 SMT Porcelain Main material 15pF,50V,5%,0603,COG 12115022
capacitor
3 C128,C129,C130,C131 4 SMT Porcelain Main material 100pF,50V,5%,0603,COG 12110122
capacitor
4 C124,C125,C126,C127 4 SMT Porcelain Main material 200pF,50V,5%,0603,COG 12120122
capacitor
5 C415,C416 2 SMT Porcelain Main material 330pF,50V,5%,0603,COG 12133122
capacitor
6 C403,C404,C941,C942,C423 5 SMT Porcelain Main material 470pF,50V,5%,0603,COG 12147122
capacitor
7 C112,C113,C114,C115,C116,C1 21 SMT Porcelain Main material 4700pF,50V,10%,0603,X7R 12147221
17,C132,C133,C136,C208,C209 capacitor
,
131
C210,C211,C212,C400,C401,C4
02,C710,C711,C712,C713
8 C121,C122,C123,C219,C220,C 15 SMT Porcelain Main material 0.01uF,50V,10%,0603,X7R 12110321
221,C422,C505,C608,C714, capacitor
C715,C914,C915,C916,C1108
9 C134,C135,C137 3 SMT Porcelain Main material 0.022uF,50V,10%,0603,X7R 12122321

capacitor
10 C1,C2,C3,C4,C5,C100,C101,C1 56 SMT Porcelain Main material 0.1uF,50V,10%,0603,X7R 12110421
02,C103,C104,C105, capacitor
C106,C107,C108,C109,C110,C2
00,C201,C202,C203,
C204,C205,C213,C214,C215,C
216,C405,C406,C407,
C408,C409,C410,C411,C412,C5
00,C501,C604,C605,
C700,C701,C702,C703,C800,C
801,C802,
C803,C804,C947,C1100,C110
1,C1102,C1103,C1104,
C1105,C1106,C1107
11 C706,C707,C708,C709 4 SMT Porcelain Main material 0.22uF,16V,10%,0603, X7R 12122421

capacitor
12 C420,C421,C948,C949 4 SMT Porcelain Main material 0.33uF,10V,10%,0603,X7R 12133421
capacitor
13 C217,C218,C419,C504,C506,C 18 SMT Porcelain Main material 1uF,16V,+80%,- 12110526
507,C600,C601, capacitor 20%,0603,Y5V
C810,C900,C901,C902,C906,C
609
C909,C911,C912,C929
14 C118,C119,C120 3 DIP porcelain Main material 1uF,63V,5% 12410501

chip capacitor
15 C950 1 Al- electrolytic Main material 220uF,20%,25V,- 12622712
capacitor 40~105
16 C922,C923 2 SMT Ta Main material 2.2uF,10V,A,16%,-55~125 12222412
capacitor
17 C944,C945 2 SMT Ta Main material 2.2uF,35V,C,20%,- 12222435
capacitor 55~125
18 C6,C502,C606,C607,C704,C7 7 SMT Ta Main material 4.7uF,16V,A,20%,-55~125 12247512
05,C933 capacitor
19 C503 1 SMT Ta Main material 4.7uF,16V,B,20%,-55~125 12247527
capacitor
20 C413,C414,C938,C940 4 SMT Ta Main material 4.7uF,25V,C,20%,- 12247534
capacitor 55~125
21 C206,C207,C937 3 SMT Ta Main material 10uF,16V,B,10%,- 12210622
capacitor 55~125
132
22 C111,C417,C418 3 SMT Ta Main material 10UF,25V,D,20%,-55~125 12210644
capacitor
23 C602,C603 2 SMT Ta Main material 47uF,16V,D,10%,- 12247642
capacitor 55~125
24 R814,R815,R816,R817,R818,R 9 SMT resistor Main material 10,5%,0603,1/10W 11110021
819,R820,R821,R822
25 R176 1 SMT resistor Main material 49.9,1%,0603,1/10W 11150020
26 R800,R801,R802 3 SMT resistor Main material 200,1%,0603,1/10W 11120120
27 R724,R725 2 SMT resistor Main material 220,1%,0603,1/10W 11122120
28 R716,R717,R824,R825,R826,R 6 SMT resistor Main material 412,1%,0603,1/10W 11141120

827
29 R812,R813 2 SMT resistor Main material 620,5%,0603,1/10W 11162121
30 R411,R412,R413,R414,R600 5 SMT resistor Main material 680,1%,0603,1/10W 11168120
31 R180,R224,R225,R226,R506,R 28 SMT resistor Main material 1K,1%,0603,1/10W 11110220

507,R508,R828,R829,R830,
R1100,R1101,R1102,R1103,R11
04,R1105,R1106,R1107,R1108,
R1109,R1110,R1111,R1112,R111
3,R1114,R1115,R1116,R1117
32 R823 1 SMT resistor Main material 1.5K,1%,0603,1/10W 11115220

805,
R806,R807,R808,R809,R810,R
811,R428
34 R912,R1127 2 SMT resistor Main material 2.2K,5%,0603,1/10W 11122221
35 R118,R119,R120,R440 4 SMT resistor Main material 3K,1%,0603,1/10W 11130220
37 R512,R513,R108,R109,R110 5 SMT resistor Main material 3.74K,1%,0603,1/10W 11137220
38 R606,R607,R1126 3 SMT resistor Main material 4.7K,1%,0603,1/10W 11147220
39 R415,R416,R417,R418,R504 5 SMT resistor Main material 4.99K,1%,0603,1/10W 11150220

168,R169,R170,R204,R205,R20
6,
R207,R208,R209,R210,R211,R2
12,R423,R424,R425,R426,R427
,
R435,R445,R500,R501,R502,R
509,R610,R1122,R1123,R1124,
R1125
133
44 R1131 1 SMT resistor Main material 11K,1%,0603,1/10W 11111320
45 R242,R728 2 SMT resistor Main material 15K,1%,0603,1/10W 11115323

203

126,R227,R228,R229,
R230,R231,R232,R718,R719,R
720,R721,R722,R723
135,R136,R137,R138,R139,
R140,R141,R142,R143,R144,R
213,R214,R215,R216,R217,
R218,R219,R220,R221,R222,R
223,R400,R401,R402,R403,
R404,R405,R406,R407,R408,R
409,R511,R704,R705,R706,
R707,R708,R709,R710,R711,R7
12,R713,R714,R715

434,R601
54 R243,R244,R245,R246,R247,R 13 SMT resistor Main material 49.9K,1%,0603,1/10W 11150320
436,R437,R438,
R439,R900,R901,R902,R903

153,R160,R162,
R164,R233,R234,R235,R236,R
602,R726,R727

831,R1120,R1121
58 R442,R1118,R1119 3 SMT resistor Main material 130K,1%,0603,1/10W 11113420

105,
R106,R107,R111,R179
R112,R113,R114,R116,R117
134
64 R1128,R1129,R1130 3 SMT resistor Main material 464K,1%,0603,1/10W 11146420
66 R420,R421,R604,R1132,R1133 5 SMT resistor Main material 1M,1%,0603,1/10W 11110520
67 R154,R155,R156,R157,R158,R 6 SMT resistor Main material 3.3M,5%,0603,1/10W 11133521

159
68 R700,R701,R702,R703 4 SMT resistor Main material 10M,5%,0603,1/10W 11110621
69 R172,R173,R174,R175 4 SMT resistor Main material 30M,5%,0603,1/10W 11130521
70 NTC800 1 Thermal-sensitive Main material 5,4A 11805020

resistor
71 VR400,VR600 2 ceramic glaze VR Main material 3266-W-10K,10% 11710303
72 VR100,VR101,VR102,VR200 8 ceramic glaze Main material 3266-W-100K,10% 11710405

,VR201,VR401,VR700,VR701 VR
73 L907 1 SMT inductance Main material 100uH,CR75-101KC 13210122
74 L900,L901,L902,L903,L904,L90 7 SMT magnetic Main material 100@100MHz,0805,400mA 13010103

5,L906 bead
75 L1,L2,L3,L4,L100,L101,L102, 55 SMT magnetic Main material 100@100MHz,0603,200mA 13010112
L103,L104,L105,L300, bead
L301,L302,L303,L304,L305,L30
6,L307,L308,L309,L310,L311,
L500,L501,L502,L503,L504,L60
0,L601,L700,L701,L702,L703,
L704,L705,L706,L707,L708,L70
9,L800,L801,L802,L803,L804,
L805,L806,L807,L808,L809,L81
0,L811,L812,L813,L814,L815
76 D100,D101,D102,D103,D10 25 SMT diode Main material LL4148,MiniMELF, 15414811
4,D105,D106,D107,D200,D400,D
401,
D402,D403,D404,D405,D40
6,D407,D408,D409,D800,D801,D
802,
D803,D804,D805
77 D414 1 SMT diode Main material 1N5817 15581711
78 D900 1 SMT diode Main material 1N5822 15582211
79 D412,D413,D600 3 SMT diode Main material ZMM9V1,MiniMELF, Column 15282031
80 D410,D411 2 SMT diode Main material ZMM8V2,MiniMELF, Column 15291031
81 Q200 1 SMT diode Main material TL431,SOT-23-3 15043131
82 D114,D115,D116,D117,D118 5 SMT diode Main material SMBJ20CA,DO-2144AA, 15020021

square
83 Q800,Q801,Q802 3 SMT triode Main material 2SA812,PNP,Mini MOLD 15281211
135
84 Q806 1 SMT triode Main material BCX5616,NPN,SOT89 15561611
85 Q803,Q804,Q805 3 SMT triode Main material MMBT2222ALT1,NPN,SOT-23 15222221
86 U803,U804,U805 3 SMT OC Main material PS2501L-1,Gull Wing 14250111
87 U800,U801 2 DIP OC Main material HCPL-4504#020,Gull Wing 14450402
88 Y1,Y800 2 DIP Xtal Main material 11.0592MHz,HC-49S,30PPM 1D110591
89 U100,U101,U102,U103,U200 5 SMT IC Main material DG412DY,SOIC-16 14041202
90 U501 1 SMT IC Main material ADG608BR,SOIC-16 14060801
91 U802 1 SMT IC Main material AT89C2051-12S,SOIC-20 14020513
92 D108,D109,D110,D111,D112,D11 13 SMT IC Main material BAT54RSLT1,SOT-23 15054022

3,D201,
D202,D415,D500,D601,D700,D70
1
93 U2 1 SMT IC Main material C8051F020,TQFP-100 14805102
94 U1 1 SMT IC Main material CY62128DV30LL-55ZI,TSOP1- 14621281

32
95 U921 1 SMT IC Main material LM2577S-ADJ,TO-263 14257701
96 U108,U109,U201,U202,U20 13 SMT IC Main material TL074CPW,TSSOP-14 14007404

3,U400,U401,
U500,U600,U700,U701,U702,U11
01
97 U110,U111,U112 3 SMT IC Main material OP4177ARU,TSSOP-14 14417701
98 U104,U105,U106 3 SMT IC Main material OPA237NA,SOT-23-5 14023701
99 U107 1 SMT IC Main material ADG801BRT,SOT-23-6 14080101
100 U900,U901 2 SMT IC Main material MIC5205-3.3BM5,SOT-23-5 14520501
101 U906 1 SMT IC Main material MIC5205-5.0BM5,SOT-23-5 14520502
102 U918,U919 2 SMT IC Main material MIC5205BM5,SOT-23-5 14520503
103 U911 1 SMT IC Main material MIC5270-5.0BM5,SOT-23-5 14527001
104 U915,U916 2 SMT IC Main material MIC5270BM5,SOT-23-5 14527002
105 U205 1 Pressure sensor Main material MPXM2053GS,1320A-02 14205300
106 U904 1 DC/DC module Main material DCM5D6HV-100,DIP16-8 52061001
107 U905 1 DC/DC module Main material DCM5D15HV-100,DIP16-8 52151001
108 U903 1 DC/DC module Main material DCM5S6HV-1W,DIP16-8 52561001
109 J600,J802 2 Electric outlet Main material PH-2A(2.00 Interval ) 19202011
110 J800 1 Electric outlet Main material PH-3A(2.00 Interval ) 19203011
111 J900 1 Electric outlet Main material PH-4A(2.00 Interval ) 19204011
112 J700,J701 2 Electric outlet Main material PH-5A(2.00 Interval ) 19205011
113 J1,J100,J801 3 Electric outlet Main material PH-6A(2.00 Interval ) 19206011
114 J302 1 Electric outlet Main material PH-2*5P(2.0mm Interval ) 19225010
136
115 J301A 1 Electric outlet Main material 1*5PIN,1.27mm Interval 19205001
116 J301B 1 Electric outlet Main material 1*8PIN,1.27mm Interval 19208001
117 J300 1 Electric outlet Main material 2*7PIN,2.54mm Interval 19214022
118 PCB 1 PCB Main material General Meditech,Inc. GAA718 51718001

V1.0
119 R904,R905,R907,R911,R915,R9 12 SMT resistor Main material 0,5%,0603,1/10W 11100021
16,R917,R918,R919,R920,R181
,R182
121 J500 1 Electric outlet Main material 2*4PIN,2.00mm Interval 1922401P
TOTAL 686
Layout of Circuit Board of Function Board
ECG BOARD PART

BOTTOM PART
137
Middle1etch
Middle3etch
1
Power part
Topetch
2
NIBP+RESP PART
Bottom PART
GNDETCH PART
3
Poweretch Part
Topetch part
4
Internal pictures
NIBP+RESP FUNTION BOARD
5
ECG FUNTION BOARD
6
MAINARM BOARD
7
APPENDIX A:
PPRODUCT SPECIFICATIONS
ENVIRONMENTAL SPECIFICATIONS
Operating
Temperature (5 to 40) C
Relative humidity 80 %
Air pressure (70 to 106) kPa
Transport and storage
Temperature (20 to 55) C
Relative humidity 93 %
Air pressure (50 to 106) kPa
8
POWER SOURCE SPECIFICATIONS
AC mains
Input voltage (100 to 240) V
Frequency 50/60 Hz
Power 80 VA
Fuse T1.6AL, 250V, 205
Operating time 8 hours
Internal battery
Number of battery 1
Type Lead-acid battery or lithium-ion battery
lithium-ion battery (G3C)
Nominal voltage 11.1 V
Capacity 4000 mAh
Operating time 1 hour (when the battery is fully charged and the monitor
measures the blood pressure every ten minutes)
Charge time 6 hours
Lead-acid battery (G3D/G3F)
Nominal voltage 12 V
Capacity 2400 mAh
Charge time 6 hours
Lead-acid battery (G3G)
Nominal voltage 12 V
Capacity 2800 mAh
Charge time 6 hours
HARDWARE SPECIFICATIONS
Display
Type Color TFT LCD
Size 10.4 inches (diagonal, G3C/G3F/G3G)
12.1 inches (diagonal, G3D)
Resolution 640480 pixels (G3C/G3F/G3G)
800600 pixels (G3D)
LED indicator
Alarm indicator 1 (red, G3D/G3F/G3G)
Power indicator 1 (green)
Charge indicator 1 (green)
Audio indicator
Speaker Giving audio alarms, heart beat tones, pulse tones and
prompt tones for wrong operation
9
Controll
knobs 3 (rotating mouse, brightness adjusting knob and volume
adjusting knob)
keys 7 (power switch, silence key, alarm key, freeze key, NIBP key,
print key and main menu key)
Connectors
Power supply 1 AC power connector
Parameter ECG, RESP, NIBP, SpO2, TEMP1, TEMP2, IBP1, IBP2,
measurement CO2
1 standard RJ45 network connector
1 standard color VGA monitor connector
1 printer connector
1 equipotential grounding connector
DATA STORAGE
Trend data 24 hours
Waveform freezing All the waveforms displayed in the channels area
can be stored
ECG SPECIFICATIONS
Lead type 3-lead: I, II and III
5-lead: I, II, III, aVR, aVL, aVF and V
Lead naming style AHA
Noise level 30 V
Frequency response Filter mode: (1 to 25) Hz
Non-filter mode: (0.5 to 75) Hz
Input offset current 0.1 A
Sensitivity selection 2.5mm/mV (1/4), 5mm/mV (1/2), 10mm/mV
(1), 20 mm/mV (2), 40mm/mV (4) and AUTO
Sweep speed 6.25mm/s, 12.5mm/s, 25mm/s and 50mm/s
Display linearity Corresponding to 15 mm of the vertical axis center, the error
should be less than 10 %
Input impedance 5 M
Common mode 60 dB
rejection
Time constant monitoring lead: 0.3 s
standard ECG lead: 3.2 s
Accuracy of standard signal 1 mV 5 %
Display stability
Time excursion The excursion after electrified for 60min is not greater than
5mm from the initial position which is the baseline position after
electrified for 15min.
Temperature excursion The average baseline excursion is not greater than 0.5mm/ in
10
the range from 5 to 40
Voltage excursion The baseline excursion is not greater than 1mm and the display
sensitivity changes not greater than 10% when the supply
voltage fluctuates transiently
Polarized voltage Corresponding to 300mV polarized DC voltage, the display
sensitivity changes not greater than 5 %
Hart rate (HR)
Measurement range (15 to 300) bpm
Measurement precision 1 bpm or 1 %, whichever is greater
ST segment measurement
Measurement range (0.8 to 0.8) mV
Measurement precision 0.02 mV or 5 %, whichever is greater
RESP SPECIFICATIONS
Measurement Thoracic impedance
technique
Lead Optional: lead I, lead II and lead III; default lead II
RR
Alarm allowable deviation 2 bpm or 10 %, whichever is greater
NIBP SPECIFICATIONS
Measurement Oscillation
technique
Displayed parameters Systolic pressure, diastolic pressure, mean arterial
pressure
Mode of operation Manual, auto and continuous
Measurement interval 2/3/4/5/6/7/8/9/10/15/20/25/30/35/40/45/50/55
in auto mode minutes and
1/1.5/2/2.5/3/3.5/4/4.5/5/5.5/6/6.5/7/7.5/8 hours
Measurement time in 5 minutes
continuous mode
Measurement range Systolic pressure (SYS): (4.0 to 36.0) kPa, or (30 to 270)
mmHg
Diastolic pressure (DIA): (1.3 to 26.7) kPa, or (10 to 200)
mmHg
Mean arterial pressure (MAP): (2.7 to 29.3) kPa, or (20 to 220)
mmHg
Measurement precision 0.4 kPa (3 mmHg) or 2 %, whichever is greater
Alarm allowable deviation 5 %
Maximum standard deviation 5 mmHg
11
TEMP SPECIFICATIONS
Number of channels 2
Displayed parameters T1, T2 and T
Measurement range (25.0 to 45.0)
Measurement precision 0.2
Response time 2.5 min
Alarm allowable deviation 0.2
SpO2 SPECIFICATIONS
Measurement range (0 to 100) %
Measurement precision (70 to 100) %: 2 %
(50 to 69) %: 3 %
(0 to 49) %: Unspecified
PR SPECIFICATIONS
IBP SPECIFICATIONS
Number of channels 2
Pressure readings Systolic pressure, diastolic pressure and mean
pressure
Pressure labels ART, CVP, RVP, LAP, RAP, PAP, ICP and LVP
Measurement range (-10 to 300) mmHg
Measurement precision 0.133 kPa (1 mmHg) or 2 %, whichever is greater
CO2 SPECIFICATIONS
Measurement Infrared absorption technique
technique
Displayed parameter EtCO2, FiCO2, RR
Measurement range (0 to 10.0) %
Precision 5.0 %: 0.28 kPa (2 mmHg)
5.0 %: 10 % of the read value
APPENDIX B:
EMC
The equipment meets the requirements of IEC 60601-1-2:2007.
12
NOTE
Use of accessories, transducers, and cables other than those specified may result in
increased emission and/or decreased immunity of the equipment.
The equipment should not be used adjacent to or stacked with other equipment, and if
adjacent or stacked use is necessary, the equipment should be observed to verify normal
operation in the configuration in which it will be used.
The equipment needs special precautions regarding EMC and needs to be installed and
put into service according to the EMC information provided below.
The equipment may be interfered with by other equipment, even if that other
equipment complies with CISPR emission requirements.
Operation of the device, in the case that the patient physiological signal is lower than the
minimum amplitude and/or value specified in the product specifications, may cause
inaccurate results.
Table 1
Guidance and declaration electromagnetic emissions
The equipment is intended for use in the electromagnetic environment

specified below.
The customer or the user of the equipment should assure that it is used in
such an environment.
Emission test Compliance Electromagnetic environment guidance
RF emissions Group 1 The equipment uses RF energy only for its
CISPR 11 internal function. Therefore, its RF emissions
are very low and are not likely to cause any
interference in nearby electronic equipment.
RF emission Class A The equipment is suitable for use in all
CISPR 11 establishments other than domestic and those
Harmonic Class A directly connected to the public low-voltage
emissions power supply network that supplies buildings
IEC 61000-3-2 used for domestic purposes.
Voltage Complian
Fluctuations/flicker ce
Emissions IEC Pst, dt (s)
61000-3-3 dmax(%)
dc (%)
Table 2
Guidance and declaration electromagnetic immunity
13
specified below.
Immunity test IEC 60601 test Compliance level Electromagnetic environment
level guidance
Electrostatic 6 kV contact 6 kV contact Floors should be wood, concrete
Discharge 8 kV air 8 kV air or ceramic tile. If floor are
(ESD) covered with synthetic material,
IEC 61000- the relative humidity should be at
4-2 least 30%.
Electrical fast 2 kV for power 2 kV for power Mains power quality should be
Transient/burst supply lines supply lines that of a typical commercial or
IEC 61000-4-4 hospital environment.
Surge 1 kV differential 1 kV differential Mains power quality should be
IEC 61000-4-5 mode mode that of a typical commercial or
2 kV common 2 kV common mode hospital environment.
mode
Voltage dips, 5 % Ut 5 % Ut Mains power quality should be
short (95 % dip in Ut) (95 % dip in Ut) that of a typical commercial or
interruptions for 0.5 cycle for 0.5 cycle hospital environment. If the user
and voltage of the Model 004 Image
variations on 40 % Ut 40 % Ut Intensifier requires continued
power supply (60 % dip in Ut) (60 % dip in Ut) operation during power mains
input lines for 5 cycles for 5 cycles interruptions. It is recommended
IEC 61000-4- that the Model 004 Image
11 70 % Ut 70 % Ut intensifier be powered from an
(30 % dip in Ut) (30 % dip in Ut) uninterruptible power supply or a
for 25 cycles for 25 cycles battery.
5 % Ut 5 % Ut
(95 % dip in Ut) (95 % dip in Ut)
for 250 S for 250 S
Power 3 A/m 3 A/m Power frequency magnetic fields
frequency should be at levels characteristic
(50Hz) of a typical location in a typical
magnetic field commercial or hospital
IEC 61000-4-8 environment.
NOTE: Ut is the A.C. mains voltage prior to application of the test level.
Table 3
14
Guidance and declaration electromagnetic immunity

specified below.
Immunity test IEC 60601 Compliance Electromagnetic environment guidance
test level level
Portable and mobile RF
communications equipment should
be used no closer to any part of the
equipment, including cables, than
the recommended separation
distance calculated from the
3 Vrms equation applicable to the frequency
Conducted RF of the transmitter. Recommended
IEC 61000-4-6 separation distance
3 Vrms d 1.2 P
150 kHz to d 1.2 P 80 MHz to 800 MHz
80 MHz 3 V/m d 2.3 P 800 MHz to 2.5 GHz
Radiated RF Where p is the maximum output power rating
IEC 61000-4-3 of the transmitter in watts (W) according to
3 V/m the transmitter manufacturer and d is the
80 MHz to recommended separation distance in metres
2.5 GHz (m).
Field strengths from fixed RF transmitter as
determined by an electromagnetic site survey
a
should be less than the compliance level in
each frequency range b Interference may occur
in the vicinity of equipment marked with the
following symbol:
Note At 80 MHz and 800 MHz, the higher frequency range applies.
Note These guidelines may not apply in all situations. Electromagnetic
propagation is affected by absorption and reflection from structures,
objects and people.
15
a. Field strengths from fixed transmitters, such as base stations for radio
(cellular/cordless) telephones and land mobile radios, amateur radio, AM and
FM radio broadcast and TV broadcast cannot be predicted theoretically with
accuracy. To assess the electromagnetic environment due to fixed RF
transmitters, an electromagnetic site survey should be considered. If the
measured field strength in the location in which the equipment is used
exceeds the applicable RF compliance level above, the equipment should be
observed to verify normal operation. If abnormal performance is observed,
additional measures may be necessary, such as reorienting or relocating the
equipment.
b. Over the frequency ranges 150kHz to 80MHz, field strengths should be
less than 3V/m.
16
Table 4
Recommended separation distances between portable and mobile RF communication and
the equipment
The equipment is intended for use in an electromagnetic environment in
which radiated RF disturbance are controlled. The customer or the user of
the equipment can help prevent electromagnetic interference by
maintaining a minimum distance between portable and mobile RF
communication equipment (transmitters) and the equipment as
recommended below, according to the maximum output power of the
communication equipment.
Rated Maximum output Separation Distance According to Frequency of Transmitter
power of M (Meters)
Transmitter W 150 kHz - 80 MHz 80 MHz - 800 MHz 800 MHz - 2.5 GHz
(Watts) d 1.2 P d 1.2 P d 2.3 P
0.01 0.12 0.12 0.23
0.1 0.37 0.37 0.74
1 1.17 1.17 2.34
10 3.69 3.69 7.38
100 11.67 11.67 23.34
For transmitters at a maximum output power not listed above, the
recommended separation distanced in meters (m) can be determined using
the equation applicable to the frequency of the transmitter, where P is the
maximum output power rating of the transmitter in watts (W) according to
the transmitter manufacturer.
NOTE: At 80 MHz and 800 MHz, the separation distance for the higher
frequency range applies.
NOTE: These guidelines may not apply in all situations. Electromagnetic
propagation is affected by absorption and reflection from structures,
objects and people.
17

Monitor G3 Manual Service V0 1 PDF

Uploaded by

Copyright:

Available Formats

Monitor G3 Manual Service V0 1 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Monitor G3 Manual Service V0 1 PDF

Uploaded by

Copyright:

Available Formats

G3 Patient Monitor

GENERAL MEDITECH, INC.

All Rights Reserved

Restrictions and Liabilities

EC Authorized Representative: Peretti Service S.A.S

UNPACKING AND CHECKING...............................................................................................................20

CHAPTER 6: WAVEFORM FREEZING AND RECALLING............................................................41

CHAPTER 10: DRUG CALCULATOR.............................................................................................52

ENTER DRUG CALCULATOR................................................................................................................52

CHAPTER 11: OTHER PATIENT VIEWING....................................................................................57

CHAPTER 12: ECG MONITORING.................................................................................................59

CHAPTER 13: RESP MONITORING...............................................................................................68

CHAPTER 14: T-RESP MONITORING............................................................................................71

CHAPTER 15: NIBP MONITORING.................................................................................................72

CHAPTER 16: TEMP MONITORING...............................................................................................79

TEMPERATURE PROBE INSTALLATION.............................................................................................79

CHAPTER 17: SPO2 MONITORING...............................................................................................82

CHAPTER 18: IBP MONITORING..................................................................................................86

CHAPTER 19: CO2 MONITORING..................................................................................................92

CHAPTER 20: MAINTENANCE.......................................................................................................96

CHAPTER 21: LABELS, PACKAGING, TRANSPORT AND STORING.........................................98

APPENDIX A: PPRODUCT SPECIFICATIONS.............................................................................100

(12) (11) (10) (9)

(10) Volume adjusting knob

G3C Side Panel

There are eight connectors on this panel:

Type BF applied part.

Attention: Consult accompanying documents (this manual).

G3C Rear Panel

(5) (6) (7) (8) (9) (10)

(1) Power switch

The key turns on or off the monitor.

(6) Equipotential ground

(8) Printer connector

(9) VGA monitor connector

G3C Mechanics Plan

(2) Silence key

(3) Alarm key

(4) Freeze key

(5) NIBP key

(6) Print key

(7) Main menu key

(9) Power switch

Type BF applied part.

Attention: Consult accompanying documents (this manual).

G3D Rear Panel

(4) (5) (6) (7)

(1) Dispersion holes

(3) Volume adjusting knob

(5) Equipotential ground

G3F Side Panel

There are six connectors on this panel:

Type BF applied part.

Attention: Consult accompanying documents (this manual).

G3F Rear Panel

(5) (6) (7) (8)

(1) Dispersion holes

(2) Power switch

The key turns on or off the monitor.