TDS-11SA Lubrication and Maintenance Guidelines
TDS-11SA Lubrication and Maintenance Guidelines
TDS-11SA Lubrication and Maintenance Guidelines
Guide Beam
1 Weekly
Grease Fitting
(4, if equipped)
Apply one pump of
general purpose grease
1 Weekly
Grease Fitting
(1 each per Bogie,
Hydraulic if equipped)
Oil Level Apply one pump of
Sight Gauge general purpose grease
Carriage Bogie
(4)
Hydraulic
Oil Filter
As Viewed Slide-type
from Rear Carriage does
(Roller-type not have
Grease Fitting Carriage Only Grease Points
Apply one pump of
general purpose grease
at beginning of tour
Daily 1
Grease Lubrication Schedule
Gear Oil DESCRIPTION NO. OF POINTS DAILY WEEKLY TYPE
Sight Gauge
Check with Gearbox Wash Pipe Assembly 1 1
Top Drive Oil Fill 2
OFF Upper Bonnet Seal 1 1
Bail Pins 2 1
Grease Fitting
Apply one pump of Rotating Link Adapter Gear 1
general purpose grease
Using hand Rotating Link Adapter 2 1
pump only IBOP Actuator Yoke and Cylinder Pins 5 1
3 Hydraulic Weekly 1 IBOP Actuator Cranks 2 1
Oil Fill
(Disconnect) Stabilizer Bushing 4 1
Grease Fittings Clamp Cylinder Gate 2 1
To each fitting apply
1 Weekly
three pumps of Carriage Assembly 8 1
Grease Fitting general purpose grease Torque Arrestor at Clamp Cylinder Area 4 1
(1 each side)
Weekly 1
Apply two pumps of Elevator Link Eyes 4
general purpose
grease See lubrication section of the TDS-11SA service manual for lubrication of electric motors
Grease Fitting
(1 each side)
Gear Oil Filter Apply one pump of
general purpose grease
Oil Lubrication Schedule
DESCRIPTION FREQUENCY TYPE
Daily 1
Replace Gearbox Oil and Perform an Oil Analysis 1 x every 6 Months 2
1 Weekly
Grease Fitting Replace Gearbox Oil Filter 1 x every 3 Months
Apply light
coat of grease (1 each side) Perform Hydraulic System Oil Analysis 1 x every 6 Months 3
to gear teeth Apply one pump of
general purpose grease Replace Hydraulic Fluid 1 x Year, or Earlier 3
Based on Oil Analysis
Daily 1
Replace Hydraulic System Filter 1 x every 3 Months
1 Daily
Oil viscosity should be adjusted based on expected ambient conditions for next six months
Grease Fittings
(if equipped)
Apply one pump of
general purpose Recommended Lubricants
grease Lubricant
Code and
1 2 3
Type General Purpose Grease Gear Oil Hydraulic Oil
Torque Arrestor
Tubes Grease Ambient
Above -20 C Below -20 C Above 21 C 7 to 30 C -6 to 16 C -10 to 85 C -15 to 75 C
Temperature
Locations Range
(Above -4 F) (Below -4 F) (Above 70 F) (45 to 85 F) (20 to 60 F) (14 to 185 F) (5 to 167 F)
Apply grease
Castrol MP Grease N/R Alpha LS-320 Alpha LS-150 Alpha LS-68 Hyspin AWS-46 Hyspin AWS-32
to torque arrestor Chevron Avi-Motive Avi-Motive W NL Gear 320 NL Gear 150 NL Gear 68 AW Hyd oil 46 AW Hyd oil 32
tubes with a brush. Grease Fittings Exxon Lidok EP2 Lidok EP1 Spartan EP320 Spartan EP150 Spartan EP68 Nuto H46 Nuto H32
To each fitting Gulf Gulf Crown EP32 Gulf Crown EP31 EP Lube HD320 EP Lube HD150 EP Lube HD68 Harmony 46AW Harmony 32AW
1 Weekly apply one pump of Mobil Mobilux EP2 Mobilux EP1 MobilGear 632 MobilGear 629 MobilGear 626 DTE 25 DTE 24
general purpose grease Shell Alvania EP2 Alvania EP1 Omala 320 Omala 150 Omala 68 Tellus 46 Tellus 32
Statoil Uniway EP2N Uniway EP1N Loadway EP320 Loadway EP150 Loadway EP68 Hydraway HMA 46 Hydraway HMA 32
Daily 1 Texaco Multifak EP2 Multifak EP1 Meropa 320 Meropa 150 Meropa 68 Rando oil HD46 Rando oil HD32
Total Multis EP2 Multis EP1 Carter EP 320 Carter EP 150 Carter EP 68 Azolla ZS 46 Azolla ZS 32
Union Unoba EP2 Unoba EP1 Extra Duty NL6EP Extra Duty NL4EP Extra Duty NL2EP Unax AW46 Unax AW32
Grease Fittings
(1 each side) General Condition Checks Daily
To each fitting
apply one pump of 1. Check for missing lockwire
general purpose grease
2. Check for loose or broken parts and leaks
Lubricate the link eyes 3. Check for damaged guide beam rollers
with pipe dope 4. Check condition of both filter gauges
Weekly 5. Check for missing cotter pins
6. Check for loose electrical connectors and check lockwire
7. Check gear oil and hydraulic fluid levels
Varco P/N 125770