Promag10 BA00082DEN 1615

BA00082D/06/EN/16.
15
71280120
Products
Solutions
Valid as of software version

V 1.04.00 (device software)
Operating Instructions
Proline Promag 10
HART
Electromagnetic flowmeter
Services
Promag 10
Table of contents
1
Safety instructions . . . . . . . . . . . . . . . . . . 4
Troubleshooting . . . . . . . . . . . . . . . . . . 73
1.1
1.2
1.3
1.4
1.5
Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installation, commissioning and operation . . . . . . 4
Operational safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Notes on safety conventions and icons . . . . . . . . . 5
Identification . . . . . . . . . . . . . . . . . . . . . . 6
2.1
2.2
2.3
Device designation . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Certificates and approvals . . . . . . . . . . . . . . . . . . . . 8
Registered trademarks . . . . . . . . . . . . . . . . . . . . . . . 8
9.1
9.2
9.3
9.4
9.5
9.6
9.7
9.8
9.9
Troubleshooting instructions . . . . . . . . . . . . . . . . 73
System error messages . . . . . . . . . . . . . . . . . . . . . 74
Process error messages . . . . . . . . . . . . . . . . . . . . . 76
Process errors without messages . . . . . . . . . . . . . 76
Response of outputs to errors . . . . . . . . . . . . . . . . 77
Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Software history . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
10
Technical data . . . . . . . . . . . . . . . . . . . . 83
Installation . . . . . . . . . . . . . . . . . . . . . . . . 9
10.1 Technical data at a glance . . . . . . . . . . . . . . . . . . . 83
3.1
3.2
3.3
3.4
Incoming acceptance, transport and storage . . . . . 9

Installation conditions . . . . . . . . . . . . . . . . . . . . . 11
Installation instructions . . . . . . . . . . . . . . . . . . . . 19
Post-installation check . . . . . . . . . . . . . . . . . . . . . 41
11
Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
4.1
4.2
4.3
4.4
4.5
Connecting the remote version . . . . . . . . . . . . . .

Connecting the measuring unit . . . . . . . . . . . . . .
Potential equalization . . . . . . . . . . . . . . . . . . . . . .
Degree of protection . . . . . . . . . . . . . . . . . . . . . . .
Post-connection check . . . . . . . . . . . . . . . . . . . . .
Operation. . . . . . . . . . . . . . . . . . . . . . . . . 55
5.1
5.2
5.3
5.4
Display and operating elements . . . . . . . . . . . . .

Brief operating instructions on the
function matrix . . . . . . . . . . . . . . . . . . . . . . . . . . .
Displaying error messages . . . . . . . . . . . . . . . . . .
Communication . . . . . . . . . . . . . . . . . . . . . . . . . . .
Commissioning . . . . . . . . . . . . . . . . . . . . 66
6.1
6.2
6.3
6.4
6.5
Function check . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching on the measuring device . . . . . . . . . .
Brief commissioning guide . . . . . . . . . . . . . . . . .
Commissioning after installing a
new electronics board . . . . . . . . . . . . . . . . . . . . . .
Empty-pipe/full-pipe adjustment . . . . . . . . . . . .
Maintenance . . . . . . . . . . . . . . . . . . . . . . 69
7.1
7.2
Exterior cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Accessories . . . . . . . . . . . . . . . . . . . . . . . 70
8.1
8.2
8.3
8.4
Device-specific accessories . . . . . . . . . . . . . . . . . .
Measuring principle-specific accessories . . . . . .
Communication-specific accessories . . . . . . . . .
Service-specific accessories . . . . . . . . . . . . . . . . .
Endress+Hauser
42
48
50
53
54
55
56
58
59
Appendix . . . . . . . . . . . . . . . . . . . . . . . 108
11.1 Illustration of the function matrix . . . . . . . . . .

11.2 Group SYSTEM UNITS . . . . . . . . . . . . . . . . . . . .
11.3 Group OPERATION . . . . . . . . . . . . . . . . . . . . . . .
11.4 USER INTERFACE . . . . . . . . . . . . . . . . . . . . . . . .
11.5 Group TOTALIZER . . . . . . . . . . . . . . . . . . . . . . .
11.6 Group CURRENT OUTPUT . . . . . . . . . . . . . . . . .
11.7 Group PULSE/STATUS OUTPUT . . . . . . . . . . . .
11.8 Group COMMUNICATION . . . . . . . . . . . . . . . . .
11.9 Group PROCESS PARAMETER . . . . . . . . . . . . .
11.10 Group SYSTEM PARAMETER . . . . . . . . . . . . . .
11.11 Group SENSOR DATA . . . . . . . . . . . . . . . . . . . . .
11.12 Group SUPERVISION . . . . . . . . . . . . . . . . . . . . .
11.13 Group SIMULATION SYSTEM . . . . . . . . . . . . . .
11.14 Group SENSOR VERSION . . . . . . . . . . . . . . . . . .
11.15 Group AMPLIFIER VERSION . . . . . . . . . . . . . . .
11.16 Factory settings . . . . . . . . . . . . . . . . . . . . . . . . . .
108
109
111
112
113
114
116
121
122
124
127
129
131
131
131
132
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
66
66
66
67
68
70
70
71
72
Safety instructions
Promag 10
Safety instructions
1.1
Designated use
The measuring device described in this Operating Manual is to be used only for measuring
the flow rate of conductive fluids in closed pipes.
Most liquids can be measured as of a minimum conductivity of 50 S/cm.
Examples:
Acids, alkalis
Drinking water, wastewater, sewage sludge
Milk, beer, wine, mineral water, etc.
Resulting from incorrect use or from use other than that designated the operational safety
of the measuring devices can be suspended. The manufacturer accepts no liability for
damages being produced from this.
1.2
Installation, commissioning and operation
Please note the following:

Installation, connection to the electricity supply, commissioning and maintenance of the
device must be carried out by trained, qualified specialists authorized to perform such work
by the facility's owner-operator. The specialist must have read and understood this
Operating Manual and must follow the instructions it contains.
The device must be operated by persons authorized and trained by the facility's owneroperator. Strict compliance with the instructions in the Operating Manual is mandatory.
With regard to special fluids, including fluids used for cleaning, Endress+Hauser will be
happy to assist in clarifying the corrosion-resistant properties of wetted materials.
However, minor changes in temperature, concentration or in the degree of contamination
in the process may result in variations in corrosion resistance. For this reason,
Endress+Hauser does not accept any responsibility with regard to the corrosion resistance
of wetted materials in a specific application.
The user is responsible for the choice of suitable wetted materials in the process.
If welding work is performed on the piping system, do not ground the welding appliance
through the Promag flowmeter.
The installer must ensure that the measuring system is correctly wired in accordance with
the wiring diagrams. The transmitter must be grounded apart from when special
protective measures are taken (e.g. galvanically isolated SELV or PELV power supply)
Invariably, local regulations governing the opening and repair of electrical devices apply.
1.3
Operational safety

Measuring systems for use in hazardous environments are accompanied by separate Ex
documentation, which is an integral part of this Operating Manual. Strict compliance with
the installation instructions and ratings as stated in this supplementary documentation is
mandatory. The symbol on the front of this Ex documentation indicates the approval and
the certification body (e.g. 0 Europe, 2 USA, 1 Canada).
The measuring device complies with the general safety requirements in accordance with
EN 61010-1, the EMC requirements of IEC/EN 61326 and NAMUR Recommendations
NE 21 and NE 43.
Depending on the application, the seals of the process connections of the Promag H sensor
require periodic replacement.
When hot fluid passes through the measuring tube, the surface temperature of the
housing increases. In the case of the sensor, in particular, users should expect
temperatures that can be close to the fluid temperature. If the temperature of the fluid is
high, implement sufficient measures to prevent burning or scalding.
4
Endress+Hauser
Promag 10
Safety instructions
The manufacturer reserves the right to modify technical data without prior notice. Your
Endress+Hauser distributor will supply you with current information and updates to these
Operating Instructions.
1.4
Return
The measuring device must be returned if repairs or a factory calibration are required, or if
the wrong measuring device has been ordered or delivered. According to legal regulations,
Endress+Hauser, as an ISO-certified company, is required to follow certain procedures when
handling returned products that are in contact with medium.
To ensure swift, safe and professional device returns, please read the return procedures and
conditions on the Endress+Hauser website at www.services.endress.com/return-material
1.5
Notes on safety conventions and icons
The devices are designed to meet state-of-the-art safety requirements, have been tested,
and left the factory in a condition in which they are safe to operate. The devices comply with
the applicable standards and regulations in accordance with EN 61010-1 "Safety
requirements for electrical equipment for measurement, control and laboratory use".
The devices can, however, be a source of danger if used incorrectly or for anything other than
the designated use. Consequently, always pay particular attention to the safety instructions
indicated in this Operating Manual by the following icons:
#
"
!
Endress+Hauser
Warning!
"Warning" indicates an action or procedure which, if not performed correctly, can result in
injury or a safety hazard. Comply strictly with the instructions and proceed with care.
Caution!
"Caution" indicates an action or procedure which, if not performed correctly, can result in
incorrect operation or destruction of the device. Comply strictly with the instructions.
Note!
"Note" indicates an action or procedure which, if not performed correctly, can have an indirect
effect on operation or trigger an unexpected response on the part of the device.
Identification
Promag 10
Identification
2.1
Device designation
The flow measuring system consists of the following components:

Promag 10 transmitter
Promag D/E/H/L/P/W sensor
In the compact version, the transmitter and sensor form a single mechanical unit; in the
remote version they are installed separately.
2.1.1
Nameplate of the transmitter
Promag 10
Order Code:
Ser.No.:
TAG No.:
2
3
4
10PXX-XXXXXXXXXXXX
12345678901
ABCDEFGHJKLMNPQRST
IP67 / NEMA/Type 4X
20-28VAC/11-40VDC
8VA/6W 50-60Hz
EPD / MS
I-OUT (HART), PULSE-OUT
5
6
-20C (-4F) <Tamb<+60C (+140F)
7
N12895
A0005395
Fig. 1:
1
2
3
4
5
6
7
8
9
Nameplate specifications for the "Promag 10" transmitter (example)

Ordering code/serial number: See the specifications on the order confirmation for the meanings of the individual letters and
digits.
Power supply, frequency, power consumption
Additional information:
EPD/MS: with Empty Pipe Detection
Outputs available:
I-OUT (HART): with current output (HART)
PULSE-OUT: with pulse/status output
Reserved for information on special products
Observe device documentation
Reserved for additional information on device version (approvals, certificates)
Permitted ambient temperature range
Degree of protection
Endress+Hauser
Promag 10
Identification
2.1.2
Nameplate of the sensor
1
2
3
4
5
PROMAG P
Order Code: 50PXX-XXXXXXXXXXXX
12345678901 RY
Ser.No.:
ABCDEFGHJKLMNPQRST
TAG No.:
2007
1.0000/0000
DN100 DIN/EN PN40 pnom =PS= 40bar
10C...150C/+14F...300F
TM:
Materials: PFA
Electrodes: 1.4435/316L
0.2% CAL
10
EPD/MS, R/B
11
-20C (-4F)<Tamb<+60C (+140F)
IP67
NEMA/Type4X
12
K-factor:
7
8
9
N12895
13
A0004374
Fig. 2:
$
25
26
27
L1 (L+) N (L)
Supply /
Versorgung /
Tension
dAlimentation
24
319740-0000
Nameplate, connections
See operating manual

Betriebsanleitung beachten
Observer Manual dInstruction
2.1.3
HART
RLmin. = 250 Ohm
12
13
I-OUT (HART)
Active: 4...20 mA
RLmax. = 700 Ohm
2
3
4
5
6
7
8
9
10
11
Ordering code/serial number: See the specifications on the order confirmation for the meanings of the individual letters and
digits.
Calibration factor with zero point
Nominal diameter/Pressure rating
Fluid temperature range
Materials: lining/measuring electrodes
Reserved for information on special products
Permitted ambient temperature range
Observe device documentation
Reserved for additional information on device version (approvals, certificates)
Calibration tolerance
Additional information (examples):
EPD/MS: with Empty Pipe Detection electrode
R/B: with reference electrode
Flow direction
PULSE-OUT
fmax: 100 Hz
Passive: 30 VDC
250 mA
Nameplate specifications for the "Promag" sensor (example)
A0005394
Fig. 3:
Endress+Hauser
Nameplate specifications for transmitter (example)
Identification
Promag 10
2.2
Certificates and approvals
The devices are designed to meet state-of-the-art safety requirements in accordance with
sound engineering practice. They have been tested and left the factory in a condition in
which they are safe to operate.
The devices comply with the applicable standards and regulations in accordance with EN
61010-1 "Safety requirements for electrical equipment for measurement, control and
laboratory use" and with the EMC requirements of IEC/EN 61326.
The measuring system described in this Operating Manual is therefore in conformity with
the statutory requirements of the EC Directives. Endress+Hauser confirms successful testing
of the device by affixing to it the CE mark.
The measuring system meets the EMC requirements of the "Australian Communications and
Media Authority (ACMA)".
2.3
Registered trademarks
KALREZ and VITON

Registered trademarks of E.I. Du Pont de Nemours & Co., Wilmington, USA
TRI-CLAMP
Registered trademark of Ladish & Co., Inc., Kenosha, USA
HART
Registered trademark of the HART Communication Foundation, Austin, USA
FieldCare, Fieldcheck, Applicator
Registered or registration-pending trademarks of Endress+Hauser Flowtec AG, Reinach, CH
Endress+Hauser
Promag 10
Installation
Installation
3.1
Incoming acceptance, transport and storage
3.1.1
Incoming acceptance
On receipt of the goods, check the following:

Check the packaging and the contents for damage.
Check the shipment, make sure nothing is missing and that the scope of supply matches
your order.
3.1.2
Transport
The following instructions apply to unpacking and to transporting the device to its final
location:
Transport the devices in the containers in which they are delivered.
Do not remove the protective plates or caps on the process connections until you are ready
to install the device. This is particularly important in the case of sensors with PTFE linings.
Special notes on flanged devices
"
Caution!
The wooden covers mounted on the flanges from the factory protect the linings on the
flanges during storage and transportation. In case of Promag L they are additionally used
to hold the lap joint flanges in place. Do not remove these covers until immediately before
the device in the pipe.
Do not lift flanged devices by the transmitter housing, or the connection housing in the
case of the remote version.
Transporting flanged devices DN 300 (12")
Use webbing slings slung round the two process connections.
Do not use chains, as they could damage the housing.
Warning!
Risk of injury if the measuring device slips. The center of gravity of the assembled measuring
device might be higher than the points around which the slings are slung.
At all times, therefore, make sure that the device does not unexpectedly turn around its axis
or slip.
A0005575
Fig. 4:
Endress+Hauser
Transporting sensors with DN 300 (12")
Installation
Promag 10
Transporting flanged devices DN 350 (14")

Use only the metal eyes on the flanges for transporting the device, lifting it and positioning
the sensor in the piping.
"
Caution!
Do not attempt to lift the sensor with the tines of a fork-lift truck beneath the metal casing.
This would buckle the casing and damage the internal magnetic coils.
A0004295
Fig. 5:
3.1.3
Transporting sensors with DN 350 (14")
Storage

Pack the measuring device in such a way as to protect it reliably against impact for storage
(and transportation). The original packaging provides optimum protection.
The storage temperature corresponds to the operating temperature range of the
measuring transmitter and the appropriate measuring sensors 86.
Do not remove the protective plates or caps on the process connections until you are ready
to install the device. This is particularly important in the case of sensors with PTFE linings.
The measuring device must be protected against direct sunlight during storage in order to
avoid unacceptably high surface temperatures.
Choose a storage location where moisture does not collect in the measuring device. This
will help prevent fungus and bacteria infestation which can damage the liner.
10
Endress+Hauser
Promag 10
Installation
3.2
Installation conditions
3.2.1
Dimensions
The dimensions and installation lengths of the sensor and transmitter can be found in the
"Technical Information" for the device in question. This document can be downloaded as a
PDF file from www.endress.com. A list of the "Technical Information" documents available is
provided in the "Documentation" section on 107.
3.2.2
Mounting location
Entrained air or gas bubble formation in the measuring tube can result in an increase in
measuring errors.
Avoid the following locations:
Highest point of a pipeline. Risk of air accumulating!
Directly upstream from a free pipe outlet in a vertical pipeline.
h 2 x DN
A0008154
Fig. 6:
Mounting location
Installation of pumps
Do not install the sensor on the intake side of a pump. This precaution is to avoid low
pressure and the consequent risk of damage to the lining of the measuring tube. Information
on the lining's resistance to partial vacuum can be found on 90.
It might be necessary to install pulse dampers in systems incorporating reciprocating,
diaphragm or peristaltic pumps. Information on the measuring system's resistance to
vibration and shock can be found on 87.
A0003203
Fig. 7:
Endress+Hauser
Installation of pumps
11
Installation
Promag 10
Partially filled pipes

Partially filled pipes with gradients necessitate a drain-type configuration.
The Empty Pipe Detection function (EPD 68) offers additional protection by detecting
empty or partially filled pipes.
"
Caution!
Risk of solids accumulating. Do not install the sensor at the lowest point in the drain. It is
advisable to install a cleaning valve.
2 x DN
5 x DN
A0008155
Fig. 8:
Installation in a partially filled pipe
Down pipes
Install a siphon or a vent valve downstream of the sensor in down pipes whose length
h 5 m (16.4 ft). This precaution is to avoid low pressure and the consequent risk of damage
to the lining of the measuring tube.
This measure also prevents the system losing prime, which could cause air pockets.
Information on the lining's resistance to partial vacuum can be found on 90.
A0008157
Fig. 9:
1
2
h
12
Measures for installation in a down pipe

Vent valve
Pipe siphon
Length of down pipe
Endress+Hauser
Promag 10
Installation
3.2.3
Orientation
An optimum orientation position helps avoid gas and air accumulations and deposits in the
measuring tube. However, Promag offers the additional Empty Pipe Detection (EPD)
function to ensure the detection of partially filled measuring tubes, e.g. in the case of
degassing fluids or varying process pressure.
Vertical orientation
This is the ideal orientation for self-emptying piping systems and for use in conjunction with
Empty Pipe Detection.
A0008158
Fig. 10:
Vertical orientation
Horizontal orientation
The measuring electrode plane should be horizontal. This prevents brief insulation of the
two measuring electrodes by entrained air bubbles.
"
Caution!
Empty Pipe Detection functions correctly only when the measuring device is installed
horizontally and the transmitter housing is facing upward ( 10). Otherwise there is no
guarantee that Empty Pipe Detection will respond if the measuring tube is only partially
filled or empty.
A
1
A
3
A0003207
Fig. 11:
1
2
3
Endress+Hauser
Horizontal orientation
EPD electrode for the detection of empty pipes (not with Promag D and Promag H (DN 2 to 15 / 1/12 to "))
Measuring electrodes for signal detection
Reference electrode for the potential equalization (not with Promag D and H)
13
Installation
Promag 10
Inlet and outlet run

If possible, install the sensor upstream from fittings such as valves, T-pieces, elbows, etc.
The following inlet and outlet runs must be observed in order to meet accuracy
specifications:
Inlet run: 5 DN
Outlet run: 2 DN
5 DN
2 DN
A0003210
Fig. 12:
3.2.4
Inlet and outlet runs
Vibrations
Secure the piping and the sensor if vibration is severe.
"
Caution!
If vibrations are too severe, we recommend the sensor and transmitter be mounted
separately. Information on resistance to vibration and shock can be found on 87.
A0003208
Fig. 13:
14
Measures to prevent vibration of the device (L > 10 m (32.8 ft))
Endress+Hauser
Promag 10
Installation
3.2.5
Foundations, supports
If the nominal diameter is DN 350 (14"), mount the sensor on a foundation of adequate
load-bearing strength.
"
Caution!
Risk of damage.
Do not support the weight of the sensor on the metal casing: the casing would buckle and
damage the internal magnetic coils.
A0003209
Fig. 14:
3.2.6
Correct support for large nominal diameters (DN 350 / 14")
Adapters
Suitable adapters to DIN EN 545 (double-flange reducers) can be used to install the sensor
in larger-diameter pipes.
The resultant increase in the rate of flow improves measuring accuracy with very slowmoving fluids. The nomogram shown here can be used to calculate the pressure loss caused
by reducers and expanders.
Note!
The nomogram only applies to liquids of viscosity similar to water.
1.
Calculate the ratio of the diameters d/D.
2.
From the nomogram read off the pressure loss as a function of flow velocity
(downstream from the reduction) and the d/D ratio.
[mbar] 100
8 m/s
7 m/s
6 m/s
10
5 m/s
4 m/s
max. 8
3 m/s
D
2 m/s
1
1 m/s
d / D 0.5
0.6
0.7
0.8
0.9
A0003213
Fig. 15:
Endress+Hauser
Pressure loss due to adapters
15
Installation
Promag 10
3.2.7
Nominal diameter and flow rate
The diameter of the pipe and the flow rate determine the nominal diameter of the sensor.
The optimum velocity of flow is between 2 and 3 m/s (6.5 to 9.8 ft/s)
The velocity of flow (v), moreover, has to be matched to the physical properties of the fluid:
v < 2 m/s (6.5 ft/s): for abrasive fluids
v > 2 m/s (6.5 ft/s): for fluids producing buildup
Note!
Flow velocity can be increased, if necessary, by reducing the nominal diameter of the sensor
( 15).
Recommended flow (SI units)
Nominal diameter
Promag D
Promag H
Promag L
Promag W
0.06 to 1.8
0.25 to 7
1 to 30
15
4 to 100
4 to 100
25
9 to 300
9 to 300
9 to 300
9 to 300
9 to 300
32
15 to 500
15 to 500
15 to 500
40
25 to 700
25 to 700
25 to 700
25 to 700
25 to 700
50
35 to 1100
35 to 1100
35 to 1100
35 to 1100
35 to 1100
65
60 to 2000
60 to 2000
60 to 2000
60 to 2000
60 to 2000
80
90 to 3000
90 to 3000
90 to 3000
90 to 3000
90 to 3000
100
145 to 4700
145 to 4700
145 to 4700
145 to 4700
145 to 4700
125
220 to 7500
220 to 7500
220 to 7500
Min./max. full scale value (v 0.3 or 10 m/s) in [m/h]
[mm]
16
Promag E/P
Min./max. full scale value (v 0.3 or 10 m/s) in [dm/min]
[mm]
150
20 to 600
20 to 600
20 to 600
200
35 to 1100
35 to 1100
35 to 1100
250
55 to 1700
55 to 1700
55 to 1700
300
80 to 2400
80 to 2400
80 to 2400
350
110 to 3300
110 to 3300
110 to 3300
375
140 to 4200
140 to 4200
400
140 to 4200
140 to 4200
140 to 4200
450
180 to 5400
180 to 5400
180 to 5400
500
220 to 6600
220 to 6600
220 to 6600
600
310 to 9600
310 to 9600
310 to 9600
700
420 to 13500
420 to 13500
750
480 to 15200
480 to 15200
800
550 to 18000
550 to 18000
900
690 to 22500
690 to 22500
1000
850 to 28000
850 to 28000
1050
950 to 40000
950 to 40000
1200
1250 to 40000
1250 to 40000
1400
1700 to 55000
1600
2200 to 70000
1800
2800 to 90000
2000
3400 to 110000
Endress+Hauser
Promag 10
Installation
Recommended flow (US units)

Nominal
diameter
Promag D
Promag H
Promag L
Promag W
Min./max. full scale value (v 0.3 or 10 m/s) in [gal/min]
[inch]
1/12"
0.015 to 0.5
1/8"
0.07 to 2
8"
0.25 to 8
"
1.0 to 27
1.0 to 27
1"
2.5 to 80
2.5 to 80
2.5 to 80
2.5 to 80
2.5 to 80
1 "
4 to 130
4 to 130
1 "
7 to 190
7 to 190
7 to 190
7 to 190
7 to 190
2"
10 to 300
10 to 300
10 to 300
10 to 300
10 to 300
2 "
16 to 500
16 to 500
16 to 500
16 to 500
16 to 500
3"
24 to 800
24 to 800
24 to 800
24 to 800
24 to 800
4"
40 to 1250
40 to 1250
40 to 1250
40 to 1250
40 to 1250
5"
60 to 1950
60 to 1950
60 to 1950
6"
90 to 2650
90 to 2650
90 to 2650
8"
155 to 4850
155 to 4850
155 to 4850
10"
250 to 7500
250 to 7500
250 to 7500
12"
350 to 10600
350 to 10600
350 to 10600
14"
500 to 15000
500 to 15000
500 to 15000
15"
600 to 19000
600 to 19000
16"
600 to 19000
600 to 19000
600 to 19000
18"
800 to 24000
800 to 24000
800 to 24000
20"
1000 to 30000
1000 to 30000
1000 to 30000
24"
1400 to 44000
1400 to 44000
1400 to 44000
28"
1900 to 60000
1900 to 60000
30"
2150 to 67000
2150 to 67000
32"
2450 to 80000
2450 to 80000
36"
3100 to 100000
3100 to 100000
40"
3800 to 125000
3800 to 125000
42"
4200 to 135000
4200 to 135000
48"
5500 to 175000
5500 to 175000
Min./max. full scale value (v 0.3 or 10 m/s) in [Mgal/d]
[inch]
Endress+Hauser
Promag E/P
54"
9 to 300
60"
12 to 380
66"
14 to 500
72"
16 to 570
78"
18 to 650
17
Installation
Promag 10
3.2.8
Length of connecting cable
In order to ensure measuring accuracy, comply with the following instructions when
installing the remote version:
Fix cable run or lay in armored conduit. Cable movements can falsify the measuring signal
especially in the case of low fluid conductivities.
Route the cable well clear of electrical machines and switching elements.
Ensure potential equalization between sensor and transmitter, if necessary.
The permitted connecting cable length Lmax is determined by the fluid conductivity (
16). A minimum conductivity of 50 S/cm is needed for all fluids.
The maximum connecting cable length is 10 m (33 ft) when empty pipe detection (EPD
68) is switched on.
[S/cm]
200
L max
100
50
[m]
50
100
200
L max
[ft]
200
400
600
A0003214
Fig. 16:
Permissible cable length for the remote version
Area shaded gray = permitted range

Lmax = connecting cable length in [m]
Fluid conductivity in [S/cm]
18
Endress+Hauser
Promag 10
Installation
3.3
Installation instructions
3.3.1
Installing the Promag D sensor
The sensor is installed between the pipe flanges with a mounting kit. The device is centered
using recesses on the sensor ( 20).
!
"
Note!
A mounting kit consisting of mounting bolts, seals, nuts and washers can be ordered
separately ( 70). Centering sleeves are provided with the device if they are required for
the installation.
Caution!
When installing the transmitter in the pipe, observe the necessary torques ( 21).
5
1
2
3
4
a0010714
Fig. 17:
1
2
3
4
5
Mounting the sensor
Nut
Washer
Mounting bolt
Centering sleeve
Seal
Seals
When installing the sensor, make sure that the seals used do not project into the pipe crosssection.
"
!
Endress+Hauser
Caution!
Risk of short circuit! Do not use electrically conductive sealing compounds such as graphite!
An electrically conductive layer could form on the inside of the measuring tube and shortcircuit the measuring signal.
Note!
Use seals with a hardness rating of 70 Shore A.
19
Installation
Promag 10
Arrangement of the mounting bolts and centering sleeves

The device is centered using recesses on the sensor. The arrangement of the mounting bolts
and the use of the centering sleeves supplied depend on the nominal diameter, the flange
standard und the pitch circle diameter.
Process connection
EN (DIN)
ASME
JIS
DN 25 to 40
(1 to 1 ")
A0010896
A0010824
A0010896
A0010825
A0010825
DN 50 (2")
1
A0010897
DN 65 ()
3
2
2
3
3
2
2
3
3
A0012170
A0012171
DN 80 (3")
1
1
1
A0010898
DN 100 (4")
A0010827
1
A0012168
A0010826
1
A0012168
A0012169
1 = Mounting bolts with centering sleeves

2 = EN (DIN) flanges: 4-hole with centering sleeves
3 = EN (DIN) flanges: 8-hole without centering sleeves
20
Endress+Hauser
Promag 10
Installation
Screw tightening torques (Promag D)

The tightening torques listed below are for lubricated threads only.
Always tighten the screws uniformly and in diagonally opposite sequence.
Overtightening the screws will deform the sealing faces or damage the seals.
The tightening torques listed below apply only to pipes not subjected to tensile stress.
The tightening torques apply to situations where an EPDM soft material flat seal (e.g. 70
Shore A) is used.
Tightening torques, mounting bolts and centering sleeves for EN (DIN) PN 16
Nominal
diameter
Mounting bolts
Centering sleeve
length
Tightening torque [Nm]

with a process flange with a
[mm]
[mm]
[mm]
smooth seal face
raised face
25
4 M12 145
54
19
19
40
4 M16 170
68
33
33
50
4 M16 185
82
41
41
65
4 M16 200
92
44
44
65
8 M16 200
29
29
80
8 M16 225
116
36
36
100
8 M16 260
147
40
40
EN (DIN) flanges: 4-hole with centering sleeves
EN (DIN) flanges: 8-hole without centering sleeves
A centering sleeve is not required. The device is centered directly via the sensor housing.
Tightening torques, mounting bolts and centering sleeves for JIS 10 K

Nominal
diameter
Mounting bolts
Centering sleeve
length
Tightening torque [Nm]

[mm]
[mm]
[mm]
smooth seal face
raised face
25
4 M16 170
54
24
24
40
4 M16 170
68
32
25
50
4 M16 185
38
30
65
4 M16 200
42
42
80
8 M16 225
36
28
100
8 M16 260
39
37
* A centering sleeve is not required. The device is centered directly via the sensor housing.
Tightening torques, mounting bolts and centering sleeves for ASME Class 150
Nominal
Centering sleeve
Tightening torque [lbf ft]
Mounting bolts
diameter
length
[inch]
[inch]
[inch]
smooth seal face
raised face
1"
4 UNC 1/2" 5.70"
*
14
7
1 "
4 UNC 1/2" 6.50"
*
21
14
2"
4 UNC 5/8" 7.50"
*
30
27
3"
4 UNC 5/8" 9.25"
*
31
31
4"
8 UNC 5/8" 10.4"
5.79
28
28
* A centering sleeve is not required. The device is centered directly via the sensor housing.
Endress+Hauser
21
Installation
Promag 10
3.3.2
"
!
Installing the Promag E sensor
Caution!
The protective covers mounted on the two sensor flanges guard the PTFE, which is turned
over the flanges. Consequently, do not remove these covers until immediately before the
sensor is installed in the pipe.
The covers must remain in place while the device is in storage.
Make sure that the lining is not damaged or removed from the flanges.
Note!
Bolts, nuts, seals, etc. are not included in the scope of supply and must be supplied by the
customer.
The sensor is designed for installation between the two piping flanges.
Observe in any case the necessary screw tightening torques on 23
If grounding disks are used, follow the mounting instructions which will be enclosed with the
shipment
a0004296
Fig. 18:
Installing the Promag E sensor
Seals
Comply with the following instructions when installing seals:
PTFE lining No seals are required!
For DIN flanges, use only seals according to EN 1514-1.
Make sure that the seals do not protrude into the piping cross-section.
"
Caution!
Ground cable
If necessary, special ground cables for potential equalization can be ordered as an accessory (
70).
Information on potential equalization and detailed mounting instructions for the use of ground
cables can be found on 50
22
Endress+Hauser
Promag 10
Installation
Tightening torques for threaded fasteners (Promag E)

Tightening torques for:
EN (DIN) 23
ASME 24
JIS 24
Promag E tightening torques for EN (DIN)
Nominal diameter
[mm]
EN (DIN)
Pressure rating [bar]
Threaded
fasteners
Max. tightening torque

[Nm]
15
PN 40
4 M 12
11
25
PN 40
4 M 12
26
32
PN 40
4 M 16
41
40
PN 40
4 M 16
52
50
PN 40
4 M 16
65
65 *
PN 16
8 M 16
43
80
PN 16
8 M 16
53
100
PN 16
8 M 16
57
125
PN 16
8 M 16
75
150
PN 16
8 M 20
99
200
PN 10
8 M 20
141
200
PN 16
12 M 20
94
250
PN 10
12 M 20
110
250
PN 16
12 M 24
131
300
PN 10
12 M 20
125
300
PN 16
12 M 24
179
350
PN 6
12 M 20
200
350
PN 10
16 M 20
188
350
PN 16
16 M 24
254
400
PN 6
16 M 20
166
400
PN 10
16 M 24
260
400
PN 16
16 M 27
330
450
PN 6
16 M 20
202
450
PN 10
20 M 24
235
450
PN 16
20 M 27
300
500
PN 6
20 M 20
176
500
PN 10
20 M 24
265
500
PN 16
20 M 30
448
600
PN 6
20 M 24
242
600
PN 10
20 M 27
345
600 *
PN 16
20 M 33
658
* Designed acc. to EN 1092-1 (not to DIN 2501)
Endress+Hauser
23
Installation
Promag 10
Promag E tightening torques for ASME

Nominal diameter
ASME

PTFE
[mm]
[inch]
Pressure rating
[lbs]
Threaded fasteners
[Nm]
15
"
Class 150
4 "
25
1"
Class 150
4 "
11
40
1 "
Class 150
4 "
24
18
50
2"
Class 150
4 5/8"
47
35
58
[lbf ft]
80
3"
Class 150
4 5/8"
79
100
4"
Class 150
8 5/8"
56
41
150
6"
Class 150
8 "
106
78
200
8"
Class 150
8 "
143
105
250
10"
Class 150
12 7/8"
135
100
300
12"
Class 150
12 7/8"
178
131
350
14"
Class 150
12 1"
260
192
400
16"
Class 150
16 1"
246
181
450
18"
Class 150
16 1 1/8"
371
274
500
20"
Class 150
20 1 1/8"
341
252
600
24"
Class 150
20 1 "
477
352
Promag E tightening torques for JIS
24
Nominal diameter
JIS
[mm]
Pressure rating
Threaded fasteners
Max. tightening torque [Nm]

PTFE
15
20K
4 M 12
16
25
20K
4 M 16
32
32
20K
4 M 16
38
40
20K
4 M 16
41
50
10K
4 M 16
54
65
10K
4 M 16
74
80
10K
8 M 16
38
100
10K
8 M 16
47
125
10K
8 M 20
80
150
10K
8 M 20
99
200
10K
12 M 20
82
250
10K
12 M 22
133
300
10K
16 M 22
99
Endress+Hauser
Promag 10
Installation
3.3.3
Installing the Promag H sensor
The sensor is supplied to order, with or without pre-installed process connections. Preinstalled process connections are secured to the sensor with 4 or 6 hex-head threaded
fasteners.
"
Caution!
The sensor might require support or additional attachments, depending on the application
and the length of the piping run. When plastic process connections are used, the sensor must
be additionally supported mechanically. A wall-mounting kit can be ordered separately from
Endress+Hauser as an accessory ( 70).
A
C
a0004301
Fig. 19:
Promag H process connections (DN 2 to 25 / 1/12 to 1", DN 40 to 100 / 1 to 4")
A = DN 2 to 25 / process connections with O-ring

Flanges (EN (DIN), ASME, JIS ),
External thread
B = DN 2 to 25 / process connections with aseptic gasket seal
Weld nipples (DIN 11850, ODT/SMS)
Tri-Clamp L14AM7
Coupling (DIN 11851, DIN 11864-1, SMS 1145 (only DN 25)
Flange DIN 11864-2
C = DN 40 to 100 / process connections with aseptic gasket seal
Weld nipples (DIN 11850, ODT/SMS)
Tri-Clamp L14AM7
Coupling (DIN 11851, DIN 11864-1, SMS 1145)
Flange DIN 11864-2
Seals
When installing the process connections, make sure that the seals are clean and correctly
centered.
"
Endress+Hauser
Caution!
With metal process connections, you must fully tighten the screws. The process
connection forms a metallic connection with the sensor, which ensures a defined
compression of the seal.
With plastic process connections, note the max. torques for lubricated threads (7 Nm / 5.2
lbf ft). With plastic flanges, always use seals between connection and counter flange.
The seals must be replaced periodically, depending on the application, particularly in the
case of gasket seals (aseptic version)!
The period between changes depends on the frequency of cleaning cycles, the cleaning
temperature and the fluid temperature. Replacement seals can be ordered as accessories
70.
25
Installation
Promag 10
Welding the transmitter into the piping (weld nipples)
"
Caution!
Risk of destroying the measuring electronics. Make sure that the welding machine is not
grounded via the sensor or the transmitter.
1.
Tack-weld the sensor into the pipe. A suitable welding jig can be ordered separately as
an accessory ( 70).
2.
Loosen the screws on the process connection flange and remove the sensor, complete
with the seal, from the pipe.
3.
Weld the process connection to the pipe.
4.
Reinstall the sensor in the pipe. Make sure that everything is clean and that the seal is
correctly seated.
Note!
If thin-walled foodstuffs pipes are not welded correctly, the heat could damage the
installed seal. It is therefore advisable to remove the sensor and the seal prior to welding.
The pipe has to be spread approximately 8 mm to permit disassembly.
Cleaning with pigs
If pigs are used for cleaning, it is essential to take the inside diameters of the measuring tube
and process connection into account. All the dimensions and lengths of the sensor and
transmitter are provided in the separate documentation "Technical Documentation".
26
Endress+Hauser
Promag 10
Installation
3.3.4
"
Installing the Promag L sensor
Caution!
The protective covers mounted on the two sensor flanges (DN 25 to 300 / 1 to 12") are used to
hold the lap joint flanges in place and to protect the PTFE liner during transportation.
Consequently, do not remove these covers until immediately before the sensor is installed in the
pipe.
Note!
customer.
shipment
To comply with the device specification, a concentrical installation in the measuring section is
required
a0004296
Fig. 20:
Installing the Promag L sensor
Seals
Hard rubber lining additional seals are always necessary.
Polyurethane lining no seals are required.
PTFE lining no seals are required.
"
Caution!
Risk of short circuit!
Do not use electrically conductive sealing compounds such as graphite! An electrically
conductive layer could form on the inside of the measuring tube and short-circuit the
measuring signal.
Ground cable
70).
cables can be found on 50.
Endress+Hauser
27
Installation
Promag 10
Screw tightening torques (Promag L)

Promag L tightening torques for EN (DIN)
Nominal diameter
EN (DIN)

Hard rubber
Polyurethane
PTFE
[Nm]
[Nm]
[mm]
Pressure rating
[bar]
Threaded
fasteners
[Nm]
25
PN 10/16
4 M 12
11
32
PN 10/16
4 M 16
16
27
40
PN 10/16
4 M 16
16
29
50
PN 10/16
4 M 16
15
40
65*
PN 10/16
8 M 16
10
22
80
PN 10/16
8 M 16
15
30
100
PN 10/16
8 M 16
20
42
125
PN 10/16
8 M 16
30
55
150
PN 10/16
8 M 20
50
90
200
PN 16
12 M 20
65
87
250
PN 16
12 M 24
126
151
300
PN 16
12 M 24
139
177
350
PN 6
12 M 20
111
120
350
PN 10
16 M 20
112
118
400
PN 6
16 M 20
90
98
400
PN 10
16 M 24
151
167
450
PN 6
16 M 20
112
126
450
PN 10
20 M 24
153
133
500
PN 6
20 M 20
119
123
500
PN 10
20 M 24
155
171
600
PN 6
20 M 24
139
147
600
PN 10
20 M 27
206
219
700
PN 6
24 M 24
148
139
700
PN 10
24 M 27
246
246
800
PN 6
24 M 27
206
182
800
PN 10
24 M 30
331
316
900
PN 6
24 M 27
230
637
900
PN 10
28 M 30
316
307
1000
PN 6
28 M 27
218
208
1000
PN 10
28 M 33
402
405
1200
PN 6
32 M 30
319
299
1200
PN 10
32 M 36
564
568
28
Endress+Hauser
Promag 10
Installation
Promag L tightening torques for ASME

Nominal diameter
ASME
Threaded
fasteners
Pressure rating
[mm]
[inch]
[lbs]
25
1"
Class 150
40
1 "
50

Hard rubber
Polyurethane
PTFE
[Nm]
[lbf ft]
[Nm]
[lbf ft]
[Nm]
[lbf ft]
4 5/8"
14
13
Class 150
8 5/8"
10
17
21
15
2"
Class 150
4 5/8"
15
11
40
29
80
3"
Class 150
4 5/8"
25
18
65
48
100
4"
Class 150
8 5/8"
20
15
44
32
150
6"
Class 150
8 "
45
33
90
66
200
8"
Class 150
8 "
65
48
87
64
250
10"
Class 150
12 7/8"
126
93
151
112
300
12"
Class 150
12 7/8"
146
108
177
131
350
14"
Class 150
12 1"
135
100
158
117
400
16"
Class 150
16 1"
128
94
150
111
450
18"
Class 150
16 1 1/8"
204
150
234
173
500
20"
Class 150
20 1 1/8"
183
135
217
160
600
24"
Class 150
20 1 "
268
198
307
226
Promag L tightening torques for AWWA

Nominal diameter
AWWA
Threaded
fasteners
Pressure rating
[mm]
[inch]
700
28"
Class D
750
30"
800

Hartgummi
Polyurethane
PTFE
[Nm]
[lbf ft]
[Nm]
[lbf ft]
[Nm]
[lbf ft]
28 1 "
247
182
292
215
Class D
28 1 "
287
212
302
223
32"
Class D
28 1 "
394
291
422
311
900
36"
Class D
32 1 "
419
309
430
317
1000
40"
Class D
36 1 "
420
310
477
352
1050
42"
Class D
36 1 "
528
389
518
382
1200
48"
Class D
44 1 "
552
407
531
392
Promag L tightening torques for AS 2129

Nominal
diameter
AS 2129
Threaded
fasteners
Pressure rating
[mm]
Endress+Hauser

Hard rubber
Polyurethane
PTFE
[Nm]
[Nm]
[Nm]
350
Table E
12 M 24
203
400
Table E
12 M 24
226
450
Table E
16 M 24
226
500
Table E
16 M 24
271
600
Table E
16 M 30
439
700
Table E
20 M 30
355
750
Table E
20 M 30
559
800
Table E
20 M 30
631
900
Table E
24 M 30
627
1000
Table E
24 M 30
634
1200
Table E
32 M 30
727
29
Installation
Promag 10
Promag L tightening torques for AS 4087

Nominal
diameter
AS 4087
Threaded
fasteners
Pressure rating
[mm]
30

Hard rubber
Polyurethane
PTFE
[Nm]
[Nm]
[Nm]
350
PN 16
12 M 24
203
375
PN 16
12 M 24
137
400
PN 16
12 M 24
226
450
PN 16
12 M 24
301
500
PN 16
16 M 24
271
600
PN 16
16 M 27
393
700
PN 16
20 M 27
330
750
PN 16
20 M 30
529
800
PN 16
20 M 33
631
900
PN 16
24 M 33
627
1000
PN 16
24 M 33
595
1200
PN 16
32 M 33
703
Endress+Hauser
Promag 10
Installation
3.3.5
"
!
Installing the Promag P sensor
Caution!
The protective covers mounted on the two sensor flanges guard the PTFE, which is turned
over the flanges. Consequently, do not remove these covers until immediately before the
sensor is installed in the pipe.
Note!
customer.
shipment
a0004296
Fig. 21:
Installing the Promag P sensor
Seals
PTFE lining No seals are required!
"
Caution!
Ground cable
70).
Tightening torques for threaded fasteners (Promag P)
Endress+Hauser
31
Installation
Promag 10

EN (DIN) 32
ASME 32
JIS 33
AS 2129 33
AS 4087 33
Promag P tightening torques for EN (DIN)
Nominal diameter
EN (DIN)
[mm]
25
PN 40
32
PN 40
40
PN 40
50
PN 40
65 *
PN 16
65
PN 40
80
PN 16
80
PN 40
100
PN 16
100
PN 40
125
PN 16
125
PN 40
150
PN 16
150
PN 40
200
PN 10
200
PN 16
200
PN 25
250
PN 10
250
PN 16
250
PN 25
300
PN 10
300
PN 16
300
PN 25
350
PN 10
350
PN 16
350
PN 25
400
PN 10
400
PN 16
400
PN 25
450
PN 10
450
PN 16
450
PN 25
500
PN 10
500
PN 16
500
PN 25
600
PN 10
600 *
PN 16
600
PN 25
Threaded
fasteners
4 M 12
4 M 16
4 M 16
4 M 16
8 M 16
8 M 16
8 M 16
8 M 16
8 M 16
8 M 20
8 M 16
8 M 24
8 M 20
8 M 24
8 M 20
12 M 20
12 M 24
12 M 20
12 M 24
12 M 27
12 M 20
12 M 24
16 M 27
16 M 20
16 M 24
16 M 30
16 M 24
16 M 27
16 M 33
20 M 24
20 M 27
20 M 33
20 M 24
20 M 30
20 M 33
20 M 27
20 M 33
20 M 36

[Nm]
26
41
52
65
43
43
53
53
57
78
75
111
99
136
141
94
138
110
131
200
125
179
204
188
254
380
260
330
488
235
300
385
265
448
533
345
658
731
Promag P tightening torques for ASME

Nominal diameter
[mm]
25
25
40
40
50
32
[inch]
1"
1"
1 "
1 "
2"
ASME
Pressure rating
[lbs]
Class 150
Class 300
Class 150
Class 300
Class 150
Threaded fasteners
4 "
4 5/8"
4 "
4 "
4 5/8"

PTFE
[Nm]
[lbf ft]
11
8
14
10
24
18
34
25
47
35
Endress+Hauser
Promag 10
Installation
Nominal diameter
[mm]
50
80
80
100
100
150
150
200
250
300
350
400
450
500
600
[inch]
2"
3"
3"
4"
4"
6"
6"
8"
10"
12"
14"
16"
18"
20"
24"
ASME
Pressure rating
[lbs]
Class 300
Class 150
Class 300
Class 150
Class 300
Class 150
Class 300
Class 150
Class 150
Class 150
Class 150
Class 150
Class 150
Class 150
Class 150
Threaded fasteners
8 5/8"
4 5/8"
8 "
8 5/8"
8 "
8 "
12 "
8 "
12 7/8"
12 7/8"
12 1"
16 1"
16 1 1/8"
20 1 1/8"
20 1 "

PTFE
[Nm]
[lbf ft]
23
17
79
58
47
35
56
41
67
49
106
78
73
54
143
105
135
100
178
131
260
192
246
181
371
274
341
252
477
352
Promag P tightening torques for JIS

Nominal diameter
[mm]
25
25
32
32
40
40
50
50
65
65
80
80
100
100
125
125
150
150
200
200
250
250
300
300
JIS
Pressure rating
10K
20K
10K
20K
10K
20K
10K
20K
10K
20K
10K
20K
10K
20K
10K
20K
10K
20K
10K
20K
10K
20K
10K
20K
Threaded fasteners
4 M 16
4 M 16
4 M 16
4 M 16
4 M 16
4 M 16
4 M 16
8 M 16
4 M 16
8 M 16
8 M 16
8 M 20
8 M 16
8 M 20
8 M 20
8 M 22
8 M 20
12 M 22
12 M 20
12 M 22
12 M 22
12 M 24
16 M 22
16 M 24

PTFE
32
32
38
38
41
41
54
27
74
37
38
57
47
75
80
121
99
108
82
121
133
212
99
183
Promag P tightening torques for AS 2129

Nominal diameter
[mm]
25
50
AS 2129
Pressure rating
Table E
Table E
Threaded
fasteners
4 M 12
4 M 16

PTFE
21
42
Threaded
fasteners
4 M 16

PTFE
42
Promag P tightening torques for AS 4087

Nominal diameter
[mm]
50
Endress+Hauser
AS 4087
Pressure rating
PN 16
33
Installation
Promag 10
3.3.6
Installing the Promag W sensor
Note!
customer.
shipment
a0004296
Fig. 22:
Installing the Promag W sensor
Seals
Hard rubber lining additional seals are always necessary.
Polyurethane lining no seals are required.
"
Caution!
Risk of short circuit!
Do not use electrically conductive sealing compounds such as graphite! An electrically
conductive layer could form on the inside of the measuring tube and short-circuit the
measuring signal.
Ground cable
70).
Screw tightening torques (Promag W)
34
Endress+Hauser
Promag 10
Installation

EN (DIN) 35
JIS 37
ASME 36
AWWA 37
AS 2129 38
AS 4087 38
Promag W tightening torques for EN (DIN)
Endress+Hauser
Nominal
diameter
EN (DIN)
[mm]
25
Threaded
fasteners
Hard rubber
Polyurethane
PN 40
4 M 12
15
32
PN 40
4 M 16
24
40
PN 40
4 M 16
31
50
PN 40
4 M 16
48
40
65*
PN 16
8 M 16
32
27
65
PN 40
8 M 16
32
27
80
PN 16
8 M 16
40
34
80
PN 40
8 M 16
40
34
100
PN 16
8 M 16
43
36
100
PN 40
8 M 20
59
50
125
PN 16
8 M 16
56
48
125
PN 40
8 M 24
83
71
150
PN 16
8 M 20
74
63
150
PN 40
8 M 24
104
88
200
PN 10
8 M 20
106
91
200
PN 16
12 M 20
70
61
200
PN 25
12 M 24
104
92
250
PN 10
12 M 20
82
71
250
PN 16
12 M 24
98
85
250
PN 25
12 M 27
150
134
300
PN 10
12 M 20
94
81
300
PN 16
12 M 24
134
118
300
PN 25
16 M 27
153
138
350
PN 6
12 M 20
111
120
350
PN 10
16 M 20
112
118
350
PN 16
16 M 24
152
165
350
PN 25
16 M 30
227
252
400
PN 6
16 M 20
90
98
400
PN 10
16 M 24
151
167
400
PN 16
16 M 27
193
215
400
PN 25
16 M 33
289
326
450
PN 6
16 M 20
112
126
450
PN 10
20 M 24
153
133
450
PN 16
20 M 27
198
196
450
PN 25
20 M 33
256
253
500
PN 6
20 M 20
119
123
500
PN 10
20 M 24
155
171
500
PN 16
20 M 30
275
300
500
PN 25
20 M 33
317
360
600
PN 6
20 M 24
139
147
600
PN 10
20 M 27
206
219
600 *
PN 16
20 M 33
415
443
600
PN 25
20 M 36
431
516
700
PN 6
24 M 24
148
139
700
PN 10
24 M 27
246
246
700
PN 16
24 M 33
278
318
35
Installation
Promag 10
Nominal
diameter
EN (DIN)
[mm]
700
Threaded
fasteners
Hard rubber
PN 25
24 M 39
449
507
800
PN 6
24 M 27
206
182
800
PN 10
24 M 30
331
316
800
PN 16
24 M 36
369
385
800
PN 25
24 M 45
664
721
900
PN 6
24 M 27
230
637
900
PN 10
28 M 30
316
307
900
PN 16
28 M 36
353
398
900
PN 25
28 M 45
690
716
1000
PN 6
28 M 27
218
208
1000
PN 10
28 M 33
402
405
1000
PN 16
28 M 39
502
518
1000
PN 25
28 M 52
970
971
1200
PN 6
32 M 30
319
299
1200
PN 10
32 M 36
564
568
1200
PN 16
32 M 45
701
753
1400
PN 6
36 M 33
430
398
1400
PN 10
36 M 39
654
618
1400
PN 16
36 M 45
729
762
1600
PN 6
40 M 33
440
417
1600
PN 10
40 M 45
946
893
1600
PN 16
40 M 52
1007
1100
1800
PN 6
44 M 36
547
521
1800
PN 10
44 M 45
961
895
1800
PN 16
44 M 52
1108
1003
2000
PN 6
48 M 39
629
605
2000
PN 10
48 M 45
1047
1092
2000
PN 16
48 M 56
1324
1261
Polyurethane
Promag W tightening torques for ASME

Nominal
diameter
36
ASME

Hard rubber
Polyurethane
[mm]
[inch]
Pressure rating
[lbs]
Threaded
fasteners
[Nm]
[lbf ft]
[Nm]
[lbf ft]
25
1"
Class 150
4 "
25
1"
Class 300
4 5/8"
40
1 "
Class 150
4 "
10
40
1 "
Class 300
4 "
15
11
50
2"
Class 150
4 5/8"
35
26
22
16
50
2"
Class 300
8 5/8"
18
13
11
80
3"
Class 150
4 5/8"
60
44
43
32
80
3"
Class 300
8 "
38
28
26
19
100
4"
Class 150
8 5/8"
42
31
31
23
100
4"
Class 300
8 "
58
43
40
30
150
6"
Class 150
8 "
79
58
59
44
150
6"
Class 300
12 "
70
52
51
38
200
8"
Class 150
8 "
107
79
80
59
250
10"
Class 150
12 7/8"
101
74
75
55
300
12"
Class 150
12 7/8"
133
98
103
76
350
14"
Class 150
12 1"
135
100
158
117
400
16"
Class 150
16 1"
128
94
150
111
450
18"
Class 150
16 1 1/8"
204
150
234
173
500
20"
Class 150
20 1 1/8"
183
135
217
160
600
24"
Class 150
20 1 "
268
198
307
226
Endress+Hauser
Promag 10
Installation
Promag W tightening torques for JIS

Nominal diameter
JIS
[mm]
Pressure rating
Threaded
fasteners
Hard rubber

Polyurethane
25
10K
4 M 16
19
25
20K
4 M 16
19
32
10K
4 M 16
22
32
20K
4 M 16
22
40
10K
4 M 16
24
40
20K
4 M 16
24
50
10K
4 M 16
40
33
50
20K
8 M 16
20
17
65
10K
4 M 16
55
45
65
20K
8 M 16
28
23
80
10K
8 M 16
29
23
80
20K
8 M 20
42
35
100
10K
8 M 16
35
29
100
20K
8 M 20
56
48
125
10K
8 M 20
60
51
125
20K
8 M 22
91
79
150
10K
8 M 20
75
63
150
20K
12 M 22
81
72
200
10K
12 M 20
61
52
200
20K
12 M 22
91
80
250
10K
12 M 22
100
87
250
20K
12 M 24
159
144
300
10K
16 M 22
74
63
300
20K
16 M 24
138
124
Promag W tightening torques for AWWA

Nominal diameter
Endress+Hauser
AWWA

Hard rubber
Polyurethane
[mm]
[inch]
Pressure
rating
Threaded
fasteners
[Nm]
[lbf ft]
[Nm]
700
28"
Class D
28 1 "
247
182
292
[lbf ft]
215
750
30"
Class D
28 1 "
287
212
302
223
800
32"
Class D
28 1 "
394
291
422
311
900
36"
Class D
32 1 "
419
309
430
317
1000
40"
Class D
36 1 "
420
310
477
352
1050
42"
Class D
36 1 "
528
389
518
382
1200
48"
Class D
44 1 "
552
407
531
392
1350
54"
Class D
44 1 "
730
538
633
467
1500
60"
Class D
52 1 "
758
559
832
614
1650
66"
Class D
52 1 "
946
698
955
704
1800
72"
Class D
60 1 "
975
719
1087
802
2000
78"
Class D
64 2"
853
629
786
580
37
Installation
Promag 10
Promag W tightening torques for AS 2129

Nominal diameter
[mm]
AS 2129
Pressure rating
Threaded
fasteners

Hard rubber
50
Table E
4 M 16
32
80
Table E
4 M 16
49
100
Table E
8 M 16
38
150
Table E
8 M 20
64
200
Table E
8 M 20
96
250
Table E
12 M 20
98
300
Table E
12 M 24
123
350
Table E
12 M 24
203
400
Table E
12 M 24
226
450
Table E
16 M 24
226
500
Table E
16 M 24
271
600
Table E
16 M 30
439
700
Table E
20 M 30
355
750
Table E
20 M 30
559
800
Table E
20 M 30
631
900
Table E
24 M 30
627
1000
Table E
24 M 30
634
1200
Table E
32 M 30
727

Hard rubber
Promag W tightening torques for AS 4087
38
Nominal diameter
[mm]
AS 4087
Pressure rating
Threaded
fasteners
50
Table E
4 M 16
32
80
PN 16
4 M 16
49
100
PN 16
4 M 16
76
150
PN 16
8 M 20
52
200
PN 16
8 M 20
77
250
PN 16
8 M 20
147
300
PN 16
12 M 24
103
350
PN 16
12 M 24
203
375
PN 16
12 M 24
137
400
PN 16
12 M 24
226
450
PN 16
12 M 24
301
500
PN 16
16 M 24
271
600
PN 16
16 M 27
393
700
PN 16
20 M 27
330
750
PN 16
20 M 30
529
800
PN 16
20 M 33
631
900
PN 16
24 M 33
627
1000
PN 16
24 M 33
595
1200
PN 16
32 M 33
703
Endress+Hauser
Promag 10
Installation
3.3.7
Turning the transmitter housing
1.
Loosen the two securing screws.
2.
Turn the bayonet lock as far as it will go.
3.
Carefully lift the transmitter housing:

Promag D: approx. 10 mm (0.39 in) above the securing screws
Promag E/H/L/P/W: to the stop
4.
Turn the transmitter housing to the desired position:

Promag D: max. 180 clockwise or max. 180 counterclockwise
Promag E/H/L/P/W: max. 280 clockwise or max. 20 counterclockwise
5.
Lower the housing into position and re-engage the bayonet catch.
6.
Retighten the two securing screws.
Esc
Esc
6
a0005393
Fig. 23:
3.3.8
Turning the transmitter housing
Turning the onsite display
1.
Unscrew cover of the electronics compartment from the transmitter housing.
2.
Remove the display module from the transmitter retaining rails.
3.
Turn the display to the desired position (max. 4 45 in each direction).
4.
Fit the display back onto the retaining rails.
5.
Screw the cover of the electronics compartment firmly back onto the transmitter
housing.
4 x 45
A0003237
Fig. 24:
Endress+Hauser
Turning the local display
39
Installation
Promag 10
3.3.9
Mounting the transmitter (remote version)
The transmitter can be mounted in the following ways:

Wall mounting
Pipe mounting (with separate mounting kit, accessories 70)
The transmitter and the sensor must be mounted separate in the following circumstances:
Poor accessibility
Lack of space
Extreme fluid/ambient temperatures (temperature ranges 86)
Severe vibration (> 2 g/2 h per day; 10 to 100 Hz)
"
Caution!
The ambient temperature range -20 to +60 C (4 to +140 F) may not be exceeded at the
mounting location. Avoid direct sunlight.
If the device is mounted to a warm pipe, make sure that the housing temperature does not
exceed +60 C (+140 F), which is the maximum permissible temperature.
Mount the transmitter as illustrated in 25.
A
248 2
(9.76 0.08)
B
238 (9.37)
ANSCHLUSSKLEMMEN - FIELD TERMINALS
mm (inch)
A0010719
Fig. 25:
A
B
40
Mounting the transmitter (remote version)

Direct wall mounting
Pipe mounting
Endress+Hauser
Promag 10
Installation
3.4
Post-installation check
Perform the following checks after installing the measuring device in the pipe:
Endress+Hauser
Device condition and specifications
Notes
Is the device damaged (visual inspection)?
Does the device correspond to specifications at the measuring point,

including process temperature and pressure, ambient temperature, minimum
fluid conductivity, measuring range, etc.?
87
Installation
Notes
Does the arrow on the sensor nameplate match the actual direction of flow
through the pipe?
Is the position of the measuring electrode plane correct?
13
Is the position of the empty pipe detection electrode correct?
13
Were all screws tightened to the specified torques when the sensor was
installed?
Promag D 21
Promag E 23
Promag L 28
Promag P 31
Promag W 34
Were the correct seals used (type, material, installation)?
Promag D 19
Promag E 22
Promag H 25
Promag L 27
Promag P 31
Promag W 34
Are the measuring point number and labeling correct (visual inspection)?
Process environment / process conditions
Notes
Were the inlet and outlet runs respected?
Inlet run 5 DN
Outlet run 2 DN
Is the measuring device protected against moisture and direct sunlight?
Is the sensor adequately protected against vibration (attachment, support)?
Acceleration up to 2 g by
analogy with IEC 600 68-2-8
41
Wiring
Promag 10
#
!
Wiring
Warning!
When using remote versions, only sensors and transmitters with the same serial number can
be connected up. Measuring errors can occur if the devices are not connected in this way.
Note!
The device does not have an internal circuit breaker. For this reason, assign the device a
switch or power-breaker switch capable of disconnecting the power supply line from the
mains.
4.1
Connecting the remote version
4.1.1
Connecting Promag D/E/H/L/P/W
Warning!
Risk of electric shock! Switch off the power supply before opening the device. Do not install
or wire the device while it is connected to the power supply. Failure to comply with this
precaution can result in irreparable damage to the electronics.
Risk of electric shock! Connect the protective conductor to the ground terminal on the
housing before the power supply is applied.
"
Caution!
Only sensors and transmitters with the same serial number can be connected to one
another. Communication problems can occur if the devices are not connected in this way.
Risk of damaging the coil driver. Always switch off the power supply before connecting or
disconnecting the coil cable.
Procedure
1.
Transmitter: Loosen the securing clamp and remove the cover from the connection
compartment (a).
2.
Sensor: Remove the cover from the connection housing (b).
3.
Feed the signal cable (c) and the coil cable (d) through the appropriate cable entries.
" Caution!
Route the connecting cables securely (see "Length of connecting cable" 18).
4.
Terminate the signal and coil current cable as indicated in the table:
Promag D/E/L/P/W Refer to the table 45
Promag H Refer to the "Cable termination" table 46
5.
Establish the wiring between the sensor and the transmitter.

The electrical wiring diagram that applies to your device can be found:
In the corresponding graphic:
26 (Promag D); 27 (Promag E/L/P/W); 28 (Promag H)
In the cover of the sensor and transmitter
! Note!
The cable shields of the Promag H sensor are grounded by means of the strain relief
terminals (see also the "Cable termination" table 46)
" Caution!
Insulate the shields of cables that are not connected to eliminate the risk of shortcircuits with neighboring cable shields inside the connection housing.
42
6.
Transmitter: Secure the cover to the connection compartment (a) and tighten the socket
head cap screw of the securing clamp.
7.
Sensor: Secure the cover on the connection housing (b).
Endress+Hauser
Promag 10
Wiring
Promag D
S2
GND
4 37 36
42 41
4 37
42 41
E2
GND
E2
S1
d
E1
n.c.
n.c.
E1
a0010695
Fig. 26:
a
b
c
d
n.c.
Connecting the remote version of Promag D
Wall-mount housing connection compartment

Cover of the sensor connection housing
Signal cable
Coil current cable
Not connected, insulated cable shields
Wire colors/Terminal No.:

5/6 = braun, 7/8 = white, 4 = green, 37/36 = yellow
Promag E/L/P/W
S2
GND
4 37 36
E2
S1
d
E1
42 41
n.c.
E1
n.c.
4 37
42 41
n.c.
E2
GND
A0012461
Fig. 27:
a
b
c
d
n.c.
Connecting the remote version of Promag E/L/P/W

Signal cable
Coil current cable

Endress+Hauser
43
Wiring
Promag 10
Promag H
S1
E1
E2
S2
GND
E
S
d
a
n.c.
4 37 36
n.c.
7
n.c.
4 37
42 41
E1
E2
GND
E
42 41
A0012477
Fig. 28:
a
b
c
d
n.c.
Connecting the remote version of Promag H

Signal cable
Coil current cable

44
Endress+Hauser
Promag 10
Wiring
Cable termination for the remote version

Promag D/E/L/P/W
Terminate the signal and coil current cables as shown in the figure below (Detail A).
Ferrules must be provided on the fine-wire cores (Detail B: m = red ferrules, 1.0 mm; n = white ferrules, 0.5 mm).
"
Caution!
When fitting the connectors, pay attention to the following points:
Signal cable Make sure that the ferrules do not touch the wire shield on the sensor side.
Minimum distance = 1 mm (exception "GND" = green cable)
Coil current cable Insulate one core of the three-core wire at the level of the core reinforcement; you only require two cores for the connection.
TRANSMITTER
Signal cable
Coil current cable
mm (inch)
mm (inch)
Esc
70 (2.76)
80 (3.15)
50 (2.0)
8 (0.32)
10 (0.4)
8 (0.32)
n
m
GND
50 (2.0)
m
m
n
m
17 (0.67)
n
n
a0005390
a0005391
SENSOR
Signal cable
Coil current cable
80 (3.15)
50 (2.0)
70 (2.76)
17 (0.67)
8 (0.32)
50 (2.0)
10 (0.4)
8 (0.32)
A
A
m
m
n
1 (0.04)
GND
mm (inch)
mm (inch)
A0003241
Endress+Hauser
A0003240
45
Wiring
Promag 10
Cable termination for the remote version

Promag H
Terminate the signal and coil current cables as shown in the figure below (Detail A).
Ferrules must be provided on the fine-wire cores (Detail B: m = red ferrules, 1.0 mm; n = white ferrules, 0.5 mm).
"
Caution!
When fitting the connectors, pay attention to the following points:
Signal cable Make sure that the ferrules do not touch the wire shield on the sensor side.
Minimum distance = 1 mm (exception "GND" = green cable).
Coil current cable Insulate one core of the three-core wire at the level of the core reinforcement; you only require two cores for the connection.
On the sensor side, reverse both cable shields approx. 15 mm over the outer jacket. The strain relief ensures an electrical connection with the
connection housing.
TRANSMITTER
Signal cable
Coil current cable
mm (inch)
mm (inch)
Esc
70 (2.76)
80 (3.15)
50 (2.0)
8 (0.32)
10 (0.4)
8 (0.32)
n
m
GND
50 (2.0)
m
m
n
m
17 (0.67)
n
a0005391
a0005390
SENSOR
Signal cable
Coil current cable
80 (3.15)
70 (2.76)
15 (0.59)
17 (0.67)
8 (0.31)
15 (0.59)
40 (1.57)
8 (0.31)
A
A
1 (0.04)
n
GND
n
m
mm (inch)
A0002647
46
mm (inch)
A0002648
Endress+Hauser
Promag 10
Wiring
4.1.2
Cable specifications
Signal cable
3 0.38 mm PVC cable with common, braided copper shield ( 7 mm) and individually
shielded cores
With Empty Pipe Detection (EPD): 4 0.38 mm PVC cable with common, braided copper
shield ( 7 mm) and individually shielded cores
Conductor resistance: 50 km
Capacitance: core/shield: 420 pF/m
Permanent operating temperature: 20 to +80 C
Cable cross-section: max. 2.5 mm
Coil cable
2 0.75 mm PVC cable with common, braided copper shield ( 7 mm)
Conductor resistance: 37 km
Capacitance: core/core, shield grounded: 120 pF/m
Operating temperature: 20 to +80 C
Test voltage for cable insulation: 1433 V AC r.m.s. 50/60 Hz or 2026 V DC
1
2
3
4
5
6
7
a
b
F06-5xWxxxxx-04-11-08-xx-003
Fig. 29:
Cable cross-section
a
b
Signal cable
Coil current cable
1
2
3
4
5
6
7
Core
Core insulation
Core shield
Core jacket
Core reinforcement
Cable shield
Outer jacket
Operation in zones of severe electrical interference:

The measuring device complies with the general safety requirements in accordance with EN
61010 and the EMC requirements of IEC/EN 61326.
"
Endress+Hauser
Caution!
Grounding is by means of the ground terminals provided for the purpose inside the
connection housing. Ensure that the stripped and twisted lengths of cable shield to the
ground terminal are as short as possible.
47
Wiring
Promag 10
4.2
Connecting the measuring unit
4.2.1
Transmitter
Warning!
Risk of electric shock!
Switch off the power supply before opening the device. Do not install or wire the device
while it is connected to the power supply. Failure to comply with this precaution can result
in irreparable damage to the electronics.
Connect the protective conductor to the ground terminal on the housing before the power
supply is applied.
Compare the specifications on the nameplate with the local supply voltage and frequency.
The national regulations governing the installation of electrical equipment also apply.
The transmitter must be included in the building fuse system.
1.
2.
Press the side latches and flip down the cover of the connection compartment.
3.
Feed the cable for the power supply and the signal cable through the appropriate cable
entries.
4.
Remove the terminal connectors from the transmitter housing and connect the cable for
the power supply and the signal cable:
Wiring diagram 30
Terminal assignment 49
5.
Plug the terminal connectors back into the transmitter housing.
! Note!
The connectors are coded so you cannot mix them up.
6.
Secure the ground cable to the ground terminal.
7.
Flip up the cover of the connection compartment.
8.
Screw the cover of the electronics compartment firmly onto the transmitter housing.
e
e
b
c
f
g
a
i
h
d
24 25 26 27
+ +
1 2
L1 N
(L+) (L-)
A0003192
Fig. 30:
a
b
c
d
e
f
g
h
i
48
Connecting the transmitter (aluminum field housing).

Electronics compartment cover
Cable for power supply: 85 to 250 V AC, 11 to 40 V DC, 20 to 28 V AC
Ground terminal for power supply cable
Terminal connector for power supply: No. 12 49 (terminal assignment)
Signal cable
Ground terminal for signal cable
Terminal connector for signal cable: No. 2427 49 (terminal assignment)
Service connector
Ground terminal for potential equalization
Endress+Hauser
Promag 10
Wiring
4.2.2
Terminal assignment
Terminal No. (outputs/power supply)
Order version
10***-***********A
24 (+) / 25 ()
26 (+) / 27 ()
1 (L1/L+) / 2 (N/L)
Pulse output
Current output HART
Power supply
Note!
Functional values of the outputs and power supply 83
4.2.3
HART connection
Users have the following connection options at their disposal:

Direct connection to transmitter by means of terminals 26(+) and 27 ()
Connection by means of the 4 to 20 mA circuit.
The measuring loop's minimum load must be at least 250 .
After commissioning, make the following settings:
CURRENT SPAN function "420 mA HART"
Switch HART write protection on or off 60
Connection of the HART handheld communicator
See also the documentation issued by the HART Communication Foundation, and in
particular HCF LIT 20: "HART, a technical summary".
250 W
27
+26
2
3
1
a0005573
Fig. 31:
1
2
3
4
Electrical connection of HART handheld Field Xpert SFX100

HART handheld Field Xpert SFX100
Auxiliary energy
Shielding
Other devices or PLC with passive input
Connection of a PC with an operating software

In order to connect a PC with an operating software (e.g. "FieldCare), a HART modem
(e.g. Commubox FXA 195) is needed.
250 W
27
+26
1
3
RS 232
a0005574
Fig. 32:
1
2
3
4
Endress+Hauser
Electrical connection of a PC with an operating software

PC with an operating software
Other evaluation devices or PLC with passive input
Shield
HART modem, e.g. Commubox FXA 195
49
Wiring
Promag 10
4.3
Potential equalization
Warning!
The measuring system must be included in the potential equalization.
Perfect measurement is only ensured when the fluid and the sensor have the same electrical
potential. This is ensured by the reference electrode integrated in the sensor as standard.
The following should also be taken into consideration for potential equalization:
Internal grounding concepts in the company
Operating conditions, such as the material/grounding of the pipes (see Table)
4.3.1
Potential equalization for Promag D
No reference electrode is integrated!

For the two ground disks of the sensor an electrical connection to the fluid is always ensured.
Exampels for connections 50
4.3.2
Potential equalization for Promag E/L/P/W
Reference electrode integrated in the sensor as standard

Exampels for connections 51
4.3.3
Potential equalization for Promag H
No reference electrode is integrated!

For the metal process connections of the sensor an electrical connection to the fluid is always
ensured.
"
Caution!
If using process connections made of a synthetic material, ground rings have to be used to
ensure that potential is equalized ( 25). The necessary ground rings can be ordered
separately from Endress+Hauser as accessories ( 70).
4.3.4
Exampels for potential equalization connections for Promag D
Standard case
Operating conditions
When using the measuring device in a:

Metal, grounded pipe
Plastic pipe
Pipe with insulating lining
Potential equalization takes place via the ground terminal
of the transmitter (standard situation).
Note!
When installing in metal pipes, we recommend you connect
the ground terminal of the transmitter housing with the
piping.
50
a0010702
Fig. 33:
Via the ground terminal of the transmitter
Endress+Hauser
Promag 10
Wiring
Special cases

Metal pipe that is not grounded
This connection method also applies in situations where:
Customary potential equalization cannot be ensured
Excessively high equalizing currents can be expected
of the transmitter and the two pipe flanges.
Here, the ground cable (copper wire, 6 mm / 0.0093 in) is
mounted directly on the conductive flange coating with
flange screws.
a0010703
Fig. 34:

and the flanges of the pipe

Pipe with a cathodic protection unit
The device is installed potential-free in the pipe.

Only the two flanges of the pipe are connected with a
ground cable (copper wire, 6 mm / 0.0093 in). Here, the
ground cable is mounted directly on the conductive flange
coating with flange screws.
Note the following when installing:
The applicable regulations regarding potential-free
installation must be observed.
There should be no electrically conductive connection
between the pipe and the device.
The mounting material must withstand the applicable
torques.
4.3.5
2
a0010704
Fig. 35:
1
2
Potential equalization and cathodic

protection
Power supply isolation transformer
Electrically isolated
Exampels for potential equalization connections for

Promag E/L/P/W
Standard case

Metal, grounded pipe
of the transmitter (standard situation).
Note!
When installing in metal pipes, we recommend you connect
the ground terminal of the transmitter housing with the
piping.
a0010702
Fig. 36:
Endress+Hauser
51
Wiring
Promag 10
Special cases

Metal pipe that is not grounded
Both sensor flanges are connected to the pipe flange by
means of a ground cable (copper wire, 6 mm / 0.0093 in)
and grounded. Connect the transmitter or sensor
connection housing, as applicable, to ground potential by
means of the ground terminal provided for the purpose.
DN 300
Ground cable installation depends on the nominal diameter:

DN 300: The ground cable is mounted directly on the
conductive flange coating with the flange screws.
DN 350: The ground cable is mounted directly on the
metal transport bracket.
DN 350
Note!
The ground cable for flange-to-flange connections can be
ordered separately as an accessory from Endress+Hauser.
a0010703
Fig. 37:

and the flanges of the pipe
Fig. 38:

Plastic pipe
Pipe with insulating lining
Potential equalization takes place using additional ground
disks, which are connected to the ground terminal via a
ground cable (copper wire, min. 6 mm / 0.0093 in). When
installing the ground disks, please comply with the enclosed
Installation Instructions.
a0010702

Pipe with a cathodic protection unit
The device is installed potential-free in the pipe.

Only the two flanges of the pipe are connected with a
ground cable (copper wire, 6 mm / 0.0093 in). Here, the
ground cable is mounted directly on the conductive flange
coating with flange screws.
Note the following when installing:
The applicable regulations regarding potential-free installation
must be observed.
There should be no electrically conductive connection
between the pipe and the device.
The mounting material must withstand the applicable
torques.
52
a0010704
Fig. 39:
1
2
Potential equalization and cathodic

protection
Power supply isolation transformer
Electrically isolated
Endress+Hauser
Promag 10
Wiring
4.4
The devices meet all the requirements of IP 67 degree of protection.

Compliance with the following points is mandatory following installation in the field or
servicing in order to ensure that IP 67 protection is maintained:
The housing seals must be clean and undamaged when inserted into their grooves. The
seals must be dried, cleaned or replaced if necessary.
All threaded fasteners and screw covers must be firmly tightened.
The cables used for connection must be of the specified outside diameter 47.
Firmly tighten the cable entries.
The cables must loop down before they enter the cable entries ("water trap"). This
arrangement prevents moisture penetrating the entry. Always install the measuring
device in such a way that the cable entries do not point up.
Remove all unused cable entries and insert plugs instead.
Do not remove the grommet from the cable entry.
b
a0001914
Fig. 40:
"
!
Endress+Hauser
Installation instructions, cable entries
Caution!
Do not loosen the threaded fasteners of the sensor housing, as otherwise the degree of
protection guaranteed by Endress+Hauser no longer applies.
Note!
The Promag E/L/P/W sensors can be supplied with IP 68 rating (permanent immersion in
water to a depth of 3 meters (10 ft)). In this case the transmitter must be installed remote
from the sensor.
The Promag L sensors with IP 68 rating are only available with stainless steel flanges.
53
Wiring
Promag 10
4.5
Post-connection check
Perform the following checks after completing electrical installation of the measuring
device:
54
Device condition and specifications
Notes
Are cables or the device damaged (visual inspection)?
Electrical connection
Notes
Does the supply voltage match the specifications on the nameplate?
85 to 250 V AC (50 to 60 Hz)

20 to 28 V AC (50 to 60 Hz),
11 to 40 V DC
Do the cables used comply with the necessary specifications?
47
Do the cables have adequate strain relief?
Is the cable type route completely isolated?

Without loops and crossovers?
Are the power-supply and signal cables correctly connected?
See the wiring diagram inside

the cover of the terminal
compartment
Only remote version:

Is the flow sensor connected to the matching transmitter electronics?
Check serial number on

nameplates of sensor and
connected transmitter.
Only remote version:

Is the connecting cable between sensor and transmitter connected correctly?
42
Are all screw terminals firmly tightened?
Have the measures for grounding/potential equalization been correctly

implemented?
50
Are all cable entries installed, firmly tightened and correctly sealed?
Cables looped as "water traps"?
53
Are all housing covers installed and firmly tightened?
Endress+Hauser
Promag 10
Operation
Operation
5.1
Display and operating elements
The local display enables you to read all important parameters directly at the measuring
point and configure the device.
The display area consists of two lines; this is where measured values are displayed, and/or
status variables (partially filled pipe, etc.). The assignment of the display lines in operating
mode is specified. The top line displays the volume flow and the bottom line displays the
totalizer status.
+48.25 xx/yy
+3702.6 x
Esc
3
A0001141
Fig. 41:
1
Endress+Hauser
Display and operating elements

Liquid crystal display
The two-line liquid-crystal display shows measured values, dialog texts, error messages and information messages. The
display as it appears when normal measuring is in progress is known as the HOME position (operating mode).
Upper display line: Shows primary measured values, e.g. volume flow [e.g. in ml/min]
Lower display line: Shows the totalizer status, [e.g. in m3]
Plus/minus keys
Enter numerical values, select parameters
Select different function groups within the function matrix
Press the +/- keys simultaneously to trigger the following functions:
Exit the function matrix step by step HOME position
Press and hold down +/- keys for longer than 3 seconds Return directly to HOME position
Cancel data entry
Enter key
HOME position Entry into the function matrix
Save the numerical values you input or settings you change
55
Operation
Promag 10
5.2
Brief operating instructions on the function matrix
Note!
See the general notes on 57.
Function matrix overview 108
Detailed description of all functions 109 ff.
The function matrix comprises two levels, namely the function groups and the functions of
the function groups.
The groups are the highest-level grouping of the control options for the device. A number of
functions is assigned to each group. You select a group in order to access the individual
functions for operating and configuring the device.
1.
HOME position F Enter the function matrix
2.
Select a function group (e.g. OPERATION)
3.
Select a function (e.g. LANGUAGE)

Change parameter/enter numerical values:
P select or enter enable code, parameters, numerical values
F save your entries
4.
Exit the function matrix:

Press and hold down Esc key (X) for longer than 3 seconds HOME position
Repeatedly press Esc key (X) return step by step to HOME position
Esc
p
m
Esc
>3s
Esc
o
E
Esc
E
E
E
E
A0001142
Fig. 42:
56
Selecting functions and configuring parameters (function matrix)
Endress+Hauser
Promag 10
Operation
5.2.1
General notes
The brief commissioning guide ( 66) is adequate for commissioning in most instances.
Complex measuring operations on the other hand necessitate additional functions that you
can configure as necessary and customize to suit your process parameters. The function
matrix, therefore, comprises a multiplicity of additional functions which, for the sake of
clarity, are arranged in a number of function groups.
Comply with the following instructions when configuring functions:
You select functions as described on 56.
You can switch off certain functions (OFF). If you do so, related functions in other function
groups will no longer be displayed.
Certain functions prompt you to confirm your data entries.
Press P to select "SURE [ YES ]" and press F again to confirm. This saves your setting or
starts a function, as applicable.
Return to the HOME position is automatic if no key is pressed for 5 minutes.
Note!
The transmitter continues to measure while data entry is in progress, i.e. the current
measured values are output via the signal outputs in the normal way.
If the power supply fails, all preset and configured values remain safely stored in the
EEPROM.
5.2.2
Enabling the programming mode
The function matrix can be disabled. Disabling the function matrix rules out the possibility
of inadvertent changes to device functions, numerical values or factory settings. A numerical
code (factory setting = 10) has to be entered before settings can be changed.
If you use a code of your choice, you exclude the possibility of unauthorized persons
accessing data, see ACCESS CODE function 111.
Comply with the following instructions when entering codes:
If programming is disabled and the P operating elements are pressed in any function, a
prompt for the code automatically appears on the display.
If "0" is specified as the customer's code, programming is always enabled.
The Endress+Hauser service organization can be of assistance if you mislay your personal
code.
"
Caution!
Changing certain parameters such as all sensor characteristics, for example, influences
numerous functions of the entire measuring system, particularly measuring accuracy.
Normally, such parameters may not be changed! Please contact Endress+Hauser if you have
any questions.
5.2.3
Disabling the programming mode
Programming is disabled if you do not press the operating elements within 60 seconds
following automatic return to the HOME position.
You can also disable programming in the "ACCESS CODE" function by entering any number
(other than the customer's code).
Endress+Hauser
57
Operation
Promag 10
5.3
Displaying error messages
5.3.1
Type of error
Errors which occur during commissioning or measuring operation are displayed

immediately. If two or more system or process errors occur, the error with the highest
priority is the one shown on the display.
The measuring system distinguishes between two types of error:
System errors 74:
This group comprises all device errors, e.g. communication errors, hardware faults, etc.
Process errors 76:
This group comprises all application errors, e.g. empty pipe, etc.
XXXXXXXXXX
#000 00:00:05
3
A0000991
Fig. 43:
1
2
3
4
5
Error messages on the display (example)

Error type:
P = process error
S = system error
Error message type:
$ = fault message
! = notice message
Error designation: e.g. EMPTY PIPE = measuring tube is only partly filled or completely empty
Error number: e.g. #401
Duration of most recent error occurrence (in hours, minutes and seconds)
5.3.2
Error message types
Notice message (!)

Displayed as Exclamation mark (!), error type (S: system error, P: process error)
The error in question has no effect on the outputs of the measuring device.
Fault message ($)
Displayed as Lightning flash ( $), error type (S: system error, P: process error).
The error in question has a direct effect on the outputs.
The response of the individual outputs (failsafe mode) can be defined in the function
matrix using the "FAILSAFE MODE" function 129.
58
Note!
For security reasons, error messages should be output via the status output.
Endress+Hauser
Promag 10
Operation
5.4
Communication
In addition to local operation, the measuring device can be configured and measured values
can be obtained by means of the HART protocol. Digital communication takes place using the
420 mA current output HART 49.
The HART protocol allows the transfer of measuring and device data between the HART
master and the field devices for configuration and diagnostics purposes.
The HART master, e.g. a handheld terminal or PC-based operating programs (such as
FieldCare), require device description (DD) files which are used to access all the information
in a HART device. Information is exclusively transferred using so-called "commands". There
are three different command classes:
Universal commands:
All HART device support and use universal commands.
The following functionalities are linked to them:
Identify HART devices
Reading digital measured values (volume flow, totalizer, etc.)
Common practice commands:
Common practice commands offer functions which are supported and can be executed by
most but not all field devices.
Device-specific commands:
These commands allow access to device-specific functions which are not HART standard.
Such commands access individual field device information, amongst other things, such as
empty/full pipe calibration values, low flow cutoff settings, etc.
Note!
The device has access to all three command classes. A list of all the "Universal commands"
and "Common practice commands" is provided on 61.
5.4.1
Operating options
For the complete operation of the measuring device, including device-specific commands,
there are DD files available to the user to provide the following operating aids and programs:
Field Xpert HART Communicator
Selecting device functions with a HART Communicator is a process involving a number of
menu levels and a special HART function matrix.
The HART manual in the carrying case of the HART Communicator contains more detailed
information on the device.
Operating program "FieldCare"
FieldCare is Endress+Hausers FDT-based plant Asset Management Tool and allows the
configuration and diagnosis of intelligent field devices. By using status information, you also
have a simple but effective tool for monitoring devices. The Proline flow measuring devices
are accessed via a service interface or via the service interface FXA193.
Operating program "SIMATIC PDM" (Siemens)
SIMATIC PDM is a standardized, manufacturer-independent tool for the operation,
configuration, maintenance and diagnosis of intelligent field devices.
Operating program "AMS" (Emerson Process Management)
AMS (Asset Management Solutions): program for operating and configuring devices.
Endress+Hauser
59
Operation
Promag 10
5.4.2
Current device description files
The following table illustrates the suitable device description file for the operating tool in
question and then indicates where these can be obtained.
HART protocol:
Valid for device software:
1.04.XX
Function DEVICE SOFTWARE
Device data HART

Manufacturer ID:
Device ID:
11hex (ENDRESS+HAUSER)
56hex
Function MANUFACTURER ID
Function DEVICE ID
HART version data:
Device Revision 5/ DD Revision 1
Software release:
01.2012
Operating program:
Sources for obtaining device descriptions:
Handheld Field Xpert SFX100
Use update function of handheld terminal
FieldCare / DTM
www.endress.com Download
CD-ROM (Endress+Hauser order number 56004088)
DVD (Endress+Hauser order number 70100690)
AMS
SIMATIC PDM
Tester/simulator:
Sources for obtaining device descriptions:
Fieldcheck
Update by means of FieldCare with the flow device FXA193/291 DTM in

the Fieldflash module
Note!
The "Fieldcheck" tester/simulator is used for testing flowmeters in the field. When used in
conjunction with the "FieldCare" software package, test results can be imported into a
database, printed out and used for official certification. Contact your Endress+Hauser
representative for more information.
5.4.3
Device variables
The following device variables are available using the HART protocol:
Code (decimal)
Device variable
OFF (not assigned)
Volume flow
250
Totalizer
At the factory, the process variables are assigned to the following device variables:
Primary process variable (PV) Volume flow
Second process variable (SV) Totalizer
Third process variable (TV) not assigned
Fourth process variable (FV) not assigned
5.4.4
Switching HART write protection on/off
The HART write protection can be switched on and off using the HART WRITE PROTECT
device function 121.
60
Endress+Hauser
Promag 10
Operation
5.4.5
Universal and common practice HART commands
The following table contains all the universal commands supported by the device.
Command No.
HART command / Access type
Command data
(numeric data in decimal form)
Response data
none
Device identification delivers information on the device

and the manufacturer. It cannot be changed.
Universal commands
0
Read unique device identifier

Access type = read
The response consists of a 12 byte device ID:

Byte 0: fixed value 254
Byte 1: Manufacturer ID, 17 = E+H
Byte 2: Device type ID, 69 = Promag 10
Byte 3: Number of preambles
Byte 4: Universal commands rev. no.
Byte 5: Device-specific commands rev. no.
Byte 6: Software revision
Byte 7: Hardware revision
Byte 8: Additional device information
Bytes 9-11: Device identification
1
Read primary process variable

Access type = read
none
Byte 0: HART unit code of the primary process variable

Bytes 1-4: Primary process variable
Factory setting: Primary process variable = Volume flow
Note!
Manufacturer-specific units are represented using the
HART unit code "240".
2
Read the primary process

variable as current in mA and
percentage of the set
measuring range
Access type = read
none
Bytes 0-3: actual current of the primary process

variable in mA
Bytes 4-7: % value of the set measuring range
Read the primary process

variable as current in mA and
four dynamic process variables
Access type = read
none
24 bytes are sent as a response:

Bytes 0-3: primary process variable current in mA
Byte 4: HART unit code of the primary process variable
Bytes 5-8: Primary process variable
Byte 9: HART unit code of the second process variable
Bytes 10-13: Second process variable
Byte 14: HART unit code of the third process variable
Bytes 15-18: Third process variable
Byte 19: HART unit code of the fourth process variable
Bytes 20-23: Fourth process variable
Factory setting:
Primary process variable = Volume flow
Second process variable = Totalizer
Third process variable = OFF (not assigned)
Fourth process variable = OFF (not assigned)
The assignment of the process variables is fixed and
cannot be changed.
Note!
6
Set HART shortform address

Access type = write
Byte 0: desired address (0 to 15)

Factory setting: 0
Byte 0: active address
Note!
With an address >0 (multidrop mode), the current
output of the primary process variable is set to 4
mA.
Endress+Hauser
61
Operation
Promag 10
Command No.
Command data
Response data
11
Read unique device

identification using the TAG
(measuring point designation)
Access type = read
Bytes 0-5: TAG
Device identification delivers information on the device

and the manufacturer. It cannot be changed.
Read user message

Access type = read
none
Read TAG, descriptor and date

Access type = read
none
12
13
The response consists of a 12 byte device ID if the given

TAG agrees with the one saved in the device:
Byte 0: fixed value 254
Byte 1: Manufacturer ID, 17 = E+H
Byte 2: Device type ID, 69 = Promag 10
Byte 4: Universal commands rev. no.
Byte 5: Device-specific commands rev. no.
Byte 6: Software revision
Byte 7: Hardware revision
Byte 8: Additional device information
Bytes 9-11: Device identification
Bytes 0-24: User message
Note!
You can write the user message using Command 17.
Bytes 0-5: TAG
Bytes 6-17: descriptor
Bytes 18-20: Date
Note!
You can write the TAG, descriptor and date using
Command 18.
14
Read sensor information on

primary process variable
none
Bytes 0-2: Sensor serial number

Byte 3: HART unit code of sensor limits and measuring
range of the primary process variable
Bytes 4-7: Upper sensor limit
Bytes 8-11: Lower sensor limit
Bytes 12-15: Minimum span
Note!
The data relate to the primary process variable
(= volume flow).
15
Read output information of

Access type = read
none
Byte 0: Alarm selection ID

Byte 1: Transfer function ID
Byte 2: HART unit code for the set measuring range of
the primary process variable
Bytes 3-6: upper range, value for 20 mA
Bytes 7-10: lower range, value for 4 mA
Bytes 11-14: Damping constant in [s]
Byte 15: Write protection ID
Byte 16: OEM dealer ID, 17 = E+H
Note!
16
Read the device production

number
Access type = read
none
Bytes 0-2: Production number
17
Write user message

Access = write
Save any 32-character text in the device. Bytes 023: Desired user message
Displays the current user message in the device:

Bytes 0-23: Current user message in the device
18
Write TAG, descriptor and date With this parameter, you can store an 8 character
Access = write
TAG, a 16 character descriptor and a date:
Bytes 0-5: TAG
Bytes 18-20: Date
19
Write the device production

number
Access = write
62
Displays the current information in the device:

Bytes 0-5: TAG
Bytes 18-20: Date
Endress+Hauser
Promag 10
Operation
The following table contains all the common practice commands supported by the
device:
Command No.
Command data
Response data
Write damping value for

Access = write
Bytes 0-3: Damping value of the primary process

variable "volume flow" in seconds
Displays the current damping value in the device:

Bytes 0-3: Damping value in seconds
Write measuring range of

Access = write
Write the desired measuring range:

Byte 0: HART unit code of the primary process
variable
Common practice commands

34
35
Factory setting:
Primary process variable = Current output
damping
Factory setting:
40
Note!
Device status reset

(configuration changed)
Access = write
none
none
Simulate input current of

Access = write
Simulation of the desired output current of the

The momentary output current of the primary process
primary process variable. An entry value of 0 exits variable is displayed as a response:
the simulation mode:
Bytes 0-3: Output current in mA
Bytes 0-3: Output current in mA
Note!
The start of the measuring range (4 mA) must
correspond to the zero flow.
If the HART unit code is not the correct one for
the process variable, the device will continue
with the last valid unit.
38
The currently set measuring range is displayed as a

response:
Byte 0: HART unit code for the set measuring range of
the primary process variable
Note!
It is also possible to execute this HART command
when write protection is activated (= ON)!
Factory setting:
Note!
You can set the assignment of device variables to
process variables using Command 51.
42
Perform master reset

Access = write
none
none
44
Write unit of primary process

variable
Access = write
Set unit of primary process variable. Only units

which are suitable for the process variable are
transferred to the device:
Byte 0: HART unit code
The current unit code of the primary process variable is

displayed as a response:
Factory setting:
Note!
Note!
If the written HART unit code is not the correct
one for the process variable, the device will
continue with the last valid unit.
If you change the unit of the primary process
variable, this has a direct impact on the system
units.
48
Read additional device status

Access = read
Endress+Hauser
none
The device status is displayed in extended form as the

response:
Coding: see table 65.
63
Operation
Promag 10
Command No.
Command data
Response data
50
none
Display of the current variable assignment of the process

variables:
Byte 0: Device variable code to the primary process
variable
Byte 1: Device variable code to the second process
variable
Byte 2: Device variable code to the third process
variable
Byte 3: Device variable code to the fourth process
variable
Read assignment of the device

variables to the four process
variables
Access = read
Factory setting:
Primary process variable: Code 1 for volume flow
Second process variable: Code 250 for totalizer
Third process variable: Code 0 for OFF (not assigned)
Fourth process variable: Code 0 for OFF (not assigned)
53
Write device variable unit

Access = write
This command sets the unit of the given device

variables. Only those units which suit the device
variable are transferred:
Byte 0: Device variable code
Code of the supported device variables:
See information 60
The current unit of the device variables is displayed in

the device as a response:
Byte 0: Device variable code
Note!
Note!
If the written unit is not the correct one for the
device variable, the device will continue with
the last valid unit.
If you change the unit of the device variable,
this has a direct impact on the system units.
59
64
Write number of preambles in

response message
Access = write
This parameter sets the number of preambles

which are inserted in the response messages:
Byte 0: Number of preambles (4 to 20)
As a response, the current number of the preambles is

displayed in the response message:
Endress+Hauser
Promag 10
Operation
5.4.6
Device status and error messages
You can read the extended device status, in this case, current error messages, via Command
"48". The command delivers information which is partly coded in bits (see table below).
Note!
You can find a detailed explanation of the device status and error messages and their
elimination on 65
Bits and bytes not listed are not assigned.
Byte
Bit
Error No.
001
Serious device error
011
Measuring amplifier has faulty EEPROM
012
Error when accessing data of the measuring amplifier EEPROM
111
Totalizer checksum error
321
Coil current of the sensor is outside the tolerance.
351
Current output:
Flow is out of range
359
Pulse output:
The pulse output frequency is out of range
10
401
Measuring tube partially filled or empty
461
EPD calibration not possible because the fluid's conductivity is either too low or
too high
463
The EPD calibration values for empty pipe and full pipe are identical, and
therefore incorrect.
12
501
Amplifier software version is loaded. Currently no other commands are possible.
14
601
Positive zero return active
691
Simulation of response to error (outputs) active
692
Simulation of volume flow active
11
18
Endress+Hauser
Short error description
65
Commissioning
Promag 10
Commissioning
6.1
Function check
Make sure that all final checks have been completed before you start up your measuring
point:
Checklist for "Post-installation check" 41
Checklist for "Post-connection check" 54
6.2
Switching on the measuring device
Once the connection checks have been successfully completed, it is time to switch on the
power supply. The device is now operational. The measuring device performs a number of
post switch-on self-tests. As this procedure progresses the following sequence of messages
appears on the local display:
PROMAG 10
V 1.XX.XX
Start-up message
Normal measuring mode commences as soon as start-up completes.

Various measured-value and/or status variables (HOME position) appear on the display.
Note!
If start-up fails, an error message indicating the cause is displayed.
6.3
Brief commissioning guide
HOME position F O
Configure display
UI language
111
Display contrast
112
Number of decimal
places
112
Select engineering units

Volume flow
109
Totalizer
113
Configure outputs
Current output
Pulse/status output
Current range
114
Operating mode
116
Full scale value
115
Pulse value
116
Pulse width
116
or
Assign status output
117
Switch-on point
117
Complex applications
The quickest way to find information on configuring additional functions is via the following pages:
Operating matrix
108
Index
135
For optimum measurement results
66
Low flow cut off
122
Empty pipe detection
122
Endress+Hauser
Promag 10
Commissioning
6.4
Commissioning after installing a new electronics

board
After startup, the device checks whether a serial number is available. If this is not the case,
the following setup is started. Installing a new electronics board 79.
6.4.1
"Commissioning" setup
Note!
The setup can no longer be called up once a serial number has been entered and stored. If
a parameter is entered incorrectly during the setup, this must be corrected in the relevant
function via the function matrix.
The appropriate information is documented on the nameplate of the sensor and on the
inside of the housing cover, 2 7.
XXX.XXX.XX
Esc
HOME-POSITION
Language
Nominal
Diameter
K-Factor
Zero
Point
EPD
Electrode
Serial
Number
Verif. S#
Equal?
No
Yes
Setup
complete
HOME
A0005396-EN
Fig. 44:
Endress+Hauser
The "Commissioning" setup starts after installation of a new electronics board if no serial number is present.
67
Commissioning
Promag 10
6.5
Empty-pipe/full-pipe adjustment
Flow cannot be measured correctly unless the measuring tube is completely full.
This status can be permanently monitored using the Empty Pipe Detection:
EPD = Empty Pipe Detection (with the help of an EPD electrode)
"
!
Caution!
More detailed information on empty-pipe and full-pipe adjustment can be found in the
description of the functions:
EPD ADJUSTMENT (carrying out the adjustment) 123.
EPD (switching empty pipe detection on and off) 122
Note!
The EPD function is not available unless the sensor is fitted with an EPD electrode.
The devices are already calibrated at the factory with water (approx. 500 S/cm).
If the fluid conductivity differs from this reference, empty-pipe/full-pipe adjustment has
to be performed again on site.
The default setting for EPD when the devices are delivered is OFF; the function has to be
activated if required.
The EPD process error can be output by means of the configurable status output.
6.5.1
Performing empty-pipe and full-pipe adjustment (EPD)
1.
Select the appropriate function in the function matrix:

HOME F R PROCESS PARAMETER F R EPD ADJUSTMENT
2.
Empty the piping. The wall of the measuring tube should still be wet with fluid during
EPD empty pipe adjustment
3.
Start empty-pipe adjustment: Select "EMPTY PIPE ADJUST" and press
4.
After empty-pipe adjustment, fill the piping with fluid.
5.
Start full-pipe adjustment: Select "FULL PIPE ADJUST" and press F to confirm.
6.
Having completed the adjustment, select the setting "OFF" and exit the function by
pressing F.
7.
Now switch on empty pipe detection in the EPD function by selecting the option "ON".
F to confirm.
" Caution!
The adjustment coefficients must be valid before you can activate the EPD function. If
adjustment is incorrect the following messages might appear on the display:
FULL = EMPTY
The adjustment values for empty pipe and full pipe are identical. In cases of this
nature you must repeat empty-pipe or full-pipe adjustment!
ADJUSTMENT NOT OK
Adjustment is not possible because the fluids conductivity is out of range.
68
Endress+Hauser
Promag 10
Maintenance
Maintenance
No special maintenance work is required.
7.1
Exterior cleaning
When cleaning the exterior of measuring devices, always use cleaning agents that do not
attack the surface of the housing and the seals.
7.2
Seals
The seals of the Promag H sensor must be replaced periodically, particularly in the case of
gasket seals (aseptic version).
The period between changes depends on the frequency of cleaning cycles, the cleaning
temperature and the fluid temperature.
Replacement seals (accessories) 70.
Endress+Hauser
69
Accessories
Promag 10
Accessories
Various accessories, which can be ordered separately from Endress+Hauser, are available for
the transmitter and the sensor. Your Endress+Hauser service organization can provide
detailed information on the specific order codes on request.
8.1
Device-specific accessories
Accessory
Description
Proline Promag 10
transmitter
Transmitter for replacement or storage. Use the order code to 10XXX

XXXXX******
define the following specifications:
8.2
70
Order code
Approvals
Degree of protection/version
Cable for remote version
Cable entry
Display/power supply/operation
Software
Outputs/inputs
Measuring principle-specific accessories
Accessory
Description
Order code
Mounting set for

Promag 10
transmitter
Mounting set for aluminum field housing (remote version).

Suitable for Pipe mounting
DK5WM B
Wall-mounting kit
for Promag H
Wall-mounting kit for the Promag H sensor.
DK5HM **
Cable for remote

version
Coil and signal cables, various lengths.
DK5CA **
Mounting kit for

Promag D, wafer
version
DKD** **
Set of seals for

Promag D
Set of seals consisting of two flange seals.
DK5DD ***
Mounting kit for

Promag H
2 process connections
Threaded fasteners
Seals
DKH** ****
Set of seals for

Promag H
For regular replacement of the seals of the Promag H sensor.
DK5HS ***
Welding jig for

Promag H
Weld nipple as process connection:

welding jig for installation in pipe.
DK5HW ***
Adapter connection
for Promag A, H
Adapter connections for installing a Promag H instead of a

Promag 30/33 A or Promag 30/33 H DN 25.
DK5HA *****
Ground cable for

Promag E/L/P/W
Ground cable for potential equalization.
DK5GC ***
Ground disk for

Promag E/L/P/W
Ground disk for potential equalization.
DK5GD * * ***
Process display
RIA45
Multifunctional 1-channel display unit:

Universal input
Transmitter power supply
Limit relay
Analog output
RIA45 ******
Process display
RIA251
Digital display device for looping into the 4 to 20 mA current

loop.
RIA251 **
Mounting bolts
Nuts incl. washers
Flange seals
Centering sleeves (if required for the flange)
Endress+Hauser
Promag 10
Accessories
Accessory
Description
Order code
Field display unit

RIA16
Digital field display device for looping into the 4 to 20 mA current

loop.
RIA16 ***
Application Manager Electronic recording, display, balancing, control, saving and

RMM621
event and alarm monitoring of analog and digital input
signals. Values and conditions determined are output by
means of analog and digital output signals. Remote
transmission of alarms, input values and calculated values
using a PSTN or GSM modem.
8.3
Endress+Hauser
RMM621 **********
Communication-specific accessories
Accessory
Description
Order code
HART Communicator
Field Xpert SFX 100
Handheld terminal for remote configuration and for obtaining SFX100 *******
measured values via the HART current output (4 to 20 mA).
Contact your Endress+Hauser representative for more
information.
Fieldgate FXA320
Gateway for remote interrogation of HART sensors and

actuators via Web browser:
2-channel analog input (4 to 20 mA)
4 binary inputs with event counter function and frequency
measurement
Communication via modem, Ethernet or GSM
Visualization via Internet/Intranet in Web browser and/or
WAP cellular phone
Limit value monitoring with alarm by e-mail or SMS
Synchronized time stamping of all measured values.
FXA320 *****
Fieldgate FXA520
Gateway for remote interrogation of HART sensors and

actuators via Web browser:
Web server for remote monitoring of up to 30 measuring
points
Intrinsically safe version [EEx ia]IIC for applications in
hazardous areas
Communication via modem, Ethernet or GSM
Visualization via Internet/Intranet in Web browser and/or
WAP cellular phone
Limit value monitoring with alarm by e-mail or SMS
Synchronized time stamping of all measured values
Remote diagnosis and remote configuration of connected
HART devices
FXA520 ****
FXA195
FXA195 *
The Commubox FXA195 connects intrinsically safe Smart
transmitters with HART protocol to the USB port of a personal
computer. This makes the remote operation of the
transmitters possible with the aid of configuration programs
(e.g. FieldCare).
Power is supplied to the Commubox by means of the USB port
71
Accessories
Promag 10
8.4
72
Service-specific accessories
Accessory
Description
Order code
Applicator
Software for selecting and planning flowmeters. The

Applicator software can be downloaded from the Internet or
ordered on CD-ROM for installation on a local PC.
information.
DXA80 *
Fieldcheck
50098801
Tester/simulator for testing flowmeters in the field. When
used in conjunction with the "FieldCare" software package, test
results can be imported into a database, printed out and used
for official certification.
information.
FieldCare
FieldCare is Endress+Hauser's FDT-based asset management

tool. It can configure all intelligent field units in your system
and helps you manage them. By using status information, it is
also a simple but effective way of checking their status and
condition.
Memograph M
graphic display
recorder
The Memograph M graphic display recorder provides

RSG40 ************
information on all the relevant process variables. Measured
values are recorded correctly, limit values are monitored and
measuring points analyzed. The data are stored in the 256
MB internal memory and also on a DSD card or USB stick.
Memograph M boasts a modular design, intuitive operation
and a comprehensive security concept. The ReadWin 2000
PC software is part of the standard package and is used for
configuring, visualizing and archiving the data captured.
The mathematics channels which are optionally available
enable continuous monitoring of specific power consumption,
boiler efficiency and other parameters which are important
for efficient energy management.
FXA193
Service interface from the device to the PC for operation via

FieldCare.
See the product page on

the Endress+Hauser
Web site:
www.endress.com
FXA193 *
Endress+Hauser
Promag 10
Troubleshooting
Troubleshooting
9.1
Troubleshooting instructions
Always start troubleshooting with the checklist below if faults occur after start-up or during
operation. The routine takes you directly to the cause of the problem and the appropriate
remedial measures.
Check the display
No display visible and
no output signals
present.
1. Check the supply voltage terminals 1, 2

2. Check the power line fuse 81
85 to 250 V AC: TR5 1 A slow-blow / 250 V
11 to 40 V DC / 20 to 28 V AC: TR5 1.6A slow-blow / 250 V
3. Measuring electronics defective order spare parts 78
No display visible, but

output signals are
present.
1. Check whether the ribbon-cable connector of the display module is correctly

plugged into the amplifier board 79
2. Display module defective order spare parts 78
3. Measuring electronics defective order spare parts 78
Display texts are in a

foreign language.
Switch off power supply. Press and hold down both the OS buttons and switch on
the measuring device. The display text will appear in English (default) and is
displayed at maximum contrast.
Measured value
indicated, but no signal
at the current or pulse
output.
Electronics board defective order spare parts 78
Error messages on display

Errors which occur during commissioning or measuring operation are displayed immediately.
Error messages consist of a variety of icons: the meanings of these icons are as follows (example):
Error type: S = system error, P = process error

Error message type: $ = fault message, ! = notice message
EMPTY PIPE = Type of error, e.g. measuring tube is only partly filled or completely empty
03:00:05 = duration of error occurrence (in hours, minutes and seconds)
#401 = error number
"
Caution!
See the information on 58!
The measuring system interprets simulations and positive zero return as system errors, but displays them as
notice message only.
Error number:
No. 001 399
No. 501 699
System error (device error) has occurred 74
Error number:
No. 401 - 499
Process error (application error) has occurred 76
Other error (without error message)

Some other error has
occurred.
Endress+Hauser
Diagnosis and rectification 76
73
Troubleshooting
Promag 10
9.2
System error messages
Serious system errors are always recognized by the device as "Fault message", and are shown
as a lightning flash ( $) on the display. Fault messages immediately affect the outputs.
Simulations and positive zero return, on the other hand, are only classed and displayed as
notice messages.
"
!
Type
Error message / No.
Caution!
In the event of a serious fault, a flowmeter might have to be returned to the manufacturer
for repair. Necessary procedures must be carried out before you return the measuring device
to Endress+Hauser 5.
Always enclose a duly completed "Declaration of Contamination" form. You will find a master
copy of this form at the back of this manual.
Note!
The error types listed in the following correspond to the factory settings.
Also observe the information on 58
Cause
Remedy
(Replace electronics board 79)
S = System error
$ = Fault message (with an effect on the outputs)
! = Notice message (without an effect on the outputs)
No. # 0xx Hardware error
S$
CRITICAL FAIL.
# 001
Serious device error
Replace electronics board.
S$
AMP HW EEPROM
# 011
Electronics board:
Defective EEPROM
S$
AMP SW EEPROM
# 012
Amplifier: Error accessing EEPROM data.
The EEPROM data blocks in which an error has

occurred are displayed in the TROUBLESHOOTING
function.
Press Enter to acknowledge the errors in question;
default values are automatically inserted instead of
the errored parameter values.
Note!
The measuring device has to be restarted if an error
has occurred in a totalizer block (see error No. 111 /
CHECKSUM TOTAL).
No. # 1xx Software error
S$
GAIN ERROR AMP

# 101
Impermissible gain deviation compared to

reference.
S$
CHECKSUM TOTAL.
# 111
Totalizer checksum error
1. Restart the measuring device

2. Replace electronics board if necessary.
No. # 3xx System limits exceeded

S$
TOL. COIL CURR.

# 321
Sensor:
Coil current is out of tolerance.
Warning!
Switch off power supply before manipulating the coil
current cable, coil current cable connector or
measuring electronics boards!
Remote version:
1. Check wiring of terminals 41/42 42
2. Check coil current cable connector.
Compact and remote version:
Replace measuring electronics boards if necessary
S!
74
CURRENT RANGE
# 351
Current output:
flow is out of range.
Change the upper or lower limit setting, as

applicable.
Increase or reduce flow, as applicable.
Endress+Hauser
Promag 10
Type
S!
Troubleshooting
Error message / No.
Cause
Remedy
(Replace electronics board 79)
RANGE PULSE
# 359
Pulse output:
the pulse output frequency is out of range.
1. Increase the setting for pulse weighting

2. When selecting the pulse width, choose a value
that can still be processed by a connected counter
(e.g. mechanical counter, PLC etc.).
Determine the pulse width:
Variant 1: Enter the minimum duration that a
pulse must be present at the connected counter
to ensure its registration.
Variant 2: Enter the maximum (pulse)
frequency as the half "reciprocal value" that a
pulse must be present at the connected counter
to ensure its registration.
Example:
The maximum input frequency of the connected
counter is 10 Hz. The pulse width to be entered is:
1 / (2 10 Hz) = 50 ms
3. Reduce flow.
No. # 5xx Application error

S
!
SW.-UPDATE ACT.
# 501
Electronics board:
New software version being loaded, no other
commands are possible at present.
Wait until process is completed and restart device.
S
!
UP-/DOWNL. ACT.
# 502
Data are being uploaded or downloaded via

FieldCare.
Wait until uploading/downloading process is finished.
Note!
Measuring device configuration is locked during
the upload/download.
No. # 6xx Simulation mode active
S
!
POS. ZERO-RET.
# 601
Positive zero return active
S
$
SIM. FAILSAFE
# 691
Simulation of response to error (outputs) active. Switch off simulation.
S
!
SIM. VOL. FLOW

# 692
Simulation of volume flow active.
Endress+Hauser
Switch off positive zero return.
Switch off simulation.
75
Troubleshooting
Promag 10
9.3
Process error messages
Process errors are permanently defined as fault messages or notice messages.

Type
Error message / No.
Cause
Remedy / spare part
P = Process error
$ = Fault message (with an effect on the outputs)
! = Notice message (without an effect on the outputs)
P!
EMPTY PIPE
# 401
Measuring tube partially filled or empty
1. Check the process conditions of the plant
P!
ADJ. NOT OK
# 461
EPD calibration not possible because the fluid's

conductivity is either too low or too high.
The EPD function cannot be used with fluids of this

nature.
P$
FULL = EMPTY
# 463
The EPD calibration values for empty pipe and full

pipe are identical, therefore incorrect.
Repeat calibration, making sure procedure is

correct 68.
2. Fill the measuring tube
9.4
Symptoms
Process errors without messages
Rectification
Remark: You may have to change or correct certain settings in functions in the function matrix in order to rectify the fault.
Flow values are negative, even
though the fluid is flowing
forwards through the pipe.
1. Remote version:
Switch off the power supply and check the wiring 42
If necessary, reverse the connections at terminals 41 and 42
2. Change the setting in the "INSTALLATION DIRECTION SENSOR" function accordingly
Measured-value reading
fluctuates even though flow is
steady.
1. Check grounding and potential equalization 50

2. Check the fluid for presence of gas bubbles.
3. In the "SYSTEM DAMPING" function increase the value
1. Check grounding and potential equalization 50

Measured-value reading shown
on display, even though the fluid
2. Check the fluid for presence of gas bubbles.
is at a standstill and the
3. Activate the "LOW FLOW CUTOFF" function, i.e. enter or increase the value for the switching point.
measuring tube is full.
Measured-value reading on
display, even though measuring
tube is empty.
1. Perform empty-pipe/full-pipe adjustment and then switch on Empty Pipe detection 68
The current output signal is

always 4 mA, irrespective of the
flow signal at any given time.
1. Select the "BUS ADDRESS" function and change the setting to "0".
The fault cannot be rectified or

some other fault not described
above has arisen.
The following options are available for tackling problems of this nature:
2. Remote version: Check the terminals of the EPD cable 42

3. Fill the measuring tube.
2. Value for creepage too high. Reduce the value in the "LOW FLOW CUTOFF" function.
Request the services of an Endress+Hauser service technician

If you contact our service organization to have a service technician sent out, please be ready to quote the following
information:
In these instances, please contact
Brief description of the fault
your Endress+Hauser service
Nameplate specifications ( 6): order code, serial number
organization.
Returning devices to Endress+Hauser
The necessary procedures on 5 must be carried out before you return a flowmeter requiring repair or
calibration to Endress+Hauser.
Always enclose a duly completed "Declaration of Conformity" form with the flowmeter. You will find a master copy of
this form at the back of this manual.
Replace transmitter electronics
Components in the measuring electronics defective order spare parts 78
76
Endress+Hauser
Promag 10
Troubleshooting
9.5
Response of outputs to errors
Note!
The response of the totalizer, current output, pulse output and status output is defined in the
FAILSAFE MODE function ( 129).
You can use positive zero return to set the signals of the current, pulse and status outputs to
their fallback value, for example when measuring has to be interrupted while a pipe is being
cleaned. This function takes priority over all other device functions: simulations, for
example, are suppressed.
Failsafe mode of outputs and totalizers
Process/system error is current
Positive zero return is activated
"
Caution!
System or process errors defined as "Notice messages" have no effect whatsoever on the inputs and outputs. See
the information on 58
Current output
MINIMUM VALUE
420 mA (25 mA) 2 mA
420 mA NAMUR 3.5 mA
420 mA US 3.75 mA
420 mA (25 mA) HART 2 mA
420 mA HART NAMUR 3.5 mA
420 mA HART US 3.75 mA
Output signal corresponds to "zero

flow"
MAXIMUM VALUE
420 mA (25 mA) 25 mA
420 mA NAMUR 22.6 mA
420 mA US 22.6 mA
420 mA (25 mA) HART 25 mA
420 mA HART NAMUR 22.6 mA
420 mA HART US 22.6 mA
HOLD VALUE
Last valid value (preceding occurrence of the fault) is
output.
ACTUAL VALUE
Measured value display on the basis of the current
flow measurement. The fault is ignored.
Pulse output
MIN/MAX VALUE FALLBACK VALUE

Signal output no pulses
Output signal corresponds to "zero

flow"
HOLD VALUE
Last valid value (preceding occurrence of the fault) is
output.
ACTUAL VALUE
Fault is ignored, i.e. normal measured-value output on
the basis of ongoing flow measurement.
Totalizer
MINIMUM/MAXIMUM VALUE STOP

The totalizers are paused until the error is rectified.
Totalizer stops
ACTUAL VALUE
The fault is ignored. The totalizer continues to count
in accordance with the current flow value.
Status output
Endress+Hauser
In the event of a fault or power supply failure:

Status output non-conductive
No effect on status output
77
Troubleshooting
Promag 10
9.6
Spare parts
Detailed troubleshooting instructions are provided in the previous sections 73

The measuring device, moreover, provides additional support in the form of continuous selfdiagnosis and error messages.
Fault rectification can entail replacing defective components with tested spare parts. The
illustration below shows the available scope of spare parts.
Note!
You can order spare parts directly from your Endress+Hauser service organization by
providing the serial number printed on the transmitter's nameplate 6.
Spare parts are shipped as sets comprising the following parts:
Spare part
Additional parts, small items (threaded fasteners, etc.)
Mounting instructions
Packaging
Es
a0005386
Fig. 45:
1
2
78
Spare parts for Promag 10 transmitter

Electronics board
Display module
Endress+Hauser
Promag 10
Troubleshooting
9.6.1
Removing and installing printed circuit boards
Field housing: removing and installing electronics boards 46
"
!
Warning!
Exposed components carry dangerous voltages. Make sure that the power supply is
switched off before you remove the cover of the electronics compartment.
Risk of damaging electronic components (ESD protection). Static electricity can damage
electronic components or impair their operability. Use a workplace with a grounded
working surface purpose-built for electrostatically sensitive devices!
If you cannot guarantee that the dielectric strength of the device is maintained in the
following steps, then an appropriate inspection must be carried out in accordance with the
manufacturers specifications.
Caution!
Use only original Endress+Hauser parts.
Note!
Commissioning a new electronics board: 67
1.
Switch off power supply.
2.
3.
Remove the local display (a) from the connection compartment cover.
4.
Press the side latches (b) and flip down the cover of the connection compartment.
5.
Disconnect the connector of the electrode signal cable (c) and the coil current cable (d).
6.
Disconnect the connector for the power supply (e) and the outputs (f).
7.
Disconnect the connector of the local display (g).
8.
Remove the cover from the connection compartment (h) by loosening the screws.
9.
Plug out the ground cable (i) of the electronics board.
10. Pull entire module (plastic retainer and electronics board) out of the housing.
11. Press the side latches (j) slightly outwards and partly push out the electronics board
towards the rear from the front.
12. Remove the electronics board from the plastic retainer from the rear.
13. Installation is the reverse of the removal procedure.
Endress+Hauser
79
Troubleshooting
Promag 10
1
Es
c
b
a
e
f
g
h
i
j
a0005388
Fig. 46:
a
b
c
d
e
f
g
h
i
j
80
Field housing: removing and installing printed circuit boards

Local display
Latches
Connector of the electrode signal cable
Connector of the coil current cable
Connector for the power supply
Connector for current output and pulse/status output
Connector of local display
Screws of electronics compartment cover
Connector of the ground cable
Latches for the electronics board
Endress+Hauser
Promag 10
Troubleshooting
9.6.2
Replacing the device fuse
Warning!
Exposed components carry dangerous voltages. Make sure that the power supply is switched
off before you remove the cover of the electronics compartment.
The main fuse is located on the electronics board ( 47).
The procedure for replacing the fuse is as follows:
"
1.
Switch off power supply.
2.
3.
Press the side latches and flip down the cover of the connection compartment.
4.
Remove the connector for the power supply (a).
5.
Replace device fuse (b). Only use the following fuse type.
Use only fuses of the following type:
Power supply 11 to 40 V DC / 20 to 28 V AC 1.6 A slow-blow / 250 V TR5
Power supply 85 to 250 V DC 1 A slow-blow / 250 V TR5
6.
Installation is the reverse of the removal procedure.
Caution!
Use only original Endress+Hauser parts.
A0005389
Fig. 47:
a
b
Endress+Hauser
Replacing the device fuse on the electronics board

Connector for power supply
Device fuse
81
Troubleshooting
Promag 10
9.7
"
Return
Caution!
Do not return a measuring device if you are not absolutely certain that all traces of hazardous
substances have been removed, e.g. substances which have penetrated crevices or diffused
through plastic.
Costs incurred for waste disposal and injury (burns, etc.) due to inadequate cleaning will be
charged to the owner-operator.
The following steps must be taken before returning a flow measuring device to
Endress+Hauser, e.g. for repair or calibration:
Always enclose a duly completed "Declaration of contamination" form. Only then can
Endress+Hauser transport, examine and repair a returned device.
Enclose special handling instructions if necessary, for example a safety data sheet as per
EC REACH Regulation No. 1907/2006.
Remove all residues. Pay special attention to the grooves for seals and crevices which could
contain residues. This is particularly important if the substance is hazardous to health, e.g.
flammable, toxic, caustic, carcinogenic, etc.
Note!
You will find a preprinted "Declaration of contamination" form at the back of these Operating
Instructions.
9.8
Disposal
Observe the regulations applicable in your country!
9.9
82
Software history
Date
Software version
Changes to software
Operating Instructions
01.2012
V 1.04.00
Introduction of new nominal diameters; faster

coil current control; calf-values to 2.5
71249469/15.14
11.2009
V 1.03.00
Introduction of Calf history
71106179/12.09
71105338/11.09
06.2009
V 1.02.00
Introduction of Promag L
71095705/06.09
03.2009
V 1.02.00
Introduction of Promag D; introduction of new

nominal diameter.
71088674/03.09
10.2004
V 1.02.00
Software modification/extension
Function: SELF CHECKING
50104787/05.05
09.2004
V 1.01.01
Software modification; extension of nominal

diameter range
50104787/04.03
06.2004
V 1.01.00
Software extension; preparation for uploading/

downloading via ToF Tool - Fieldtool Package
50104787/04.03
08.2003
V 1.00.02
Production-related software modification
50104787/04.03
01.2003
V 1.00.00
Original software.
Compatible with:
ToF Tool - Fieldtool Package,
HART Communicator DXR 275
(from OS 4.6) with Rev. 1, DD 1.
50104787/04.03
Note!
Uploads or downloads between the individual software versions are only possible with a
special service software.
Endress+Hauser
Promag 10
Technical data
10
Technical data
10.1
Technical data at a glance
10.1.1
Application
10.1.2
Function and system design
Measuring principle
Electromagnetic flow measurement on the basis of Faradays Law.
Measuring system
6
10.1.3
Input
Measured variable
Flow velocity (proportional to induced voltage)
Measuring range
Typically v = 0.01 to 10 m/s (0.033 to 33 ft/s) with the specified accuracy
Operable flow range
Over 1000 : 1
10.1.4
Output
Output signal
Current output
Galvanically isolated
Active: 4 to 20 mA, RL <700 (for HART: RL 250 )
Full scale value adjustable
Temperature coefficient: typ. 2 A/C, resolution: 1.5 A
Pulse/status output:
Galvanically isolated
Passive: 30 V DC / 250 mA
Open collector
Can be configured as:
Pulse output
Pulse value and pulse polarity can be selected, max. pulse width adjustable (5 to 2000
ms), pulse frequency max. 100 Hz
Status output
For example, can be configured for error messages, empty pipe detection, flow
recognition, limit value
Endress+Hauser
83
Technical data
Promag 10
Signal on alarm
Current output
Failsafe mode can be selected (e.g. in accordance with NAMUR Recommendation NE 43)
129
Pulse output
Failsafe mode can be selected 129
Status output
"Not conductive" in the event of fault or power supply failure
Load
See "Output signal"
Low flow cut off
Low flow cut off, switch-on point can be selected as required
Galvanic isolation
All circuits for inputs, outputs, and power supply are galvanically isolated from each other.
10.1.5
Power supply
Electrical connections
42
Supply voltage (power supply)
20 to 28 V AC, 45 to 65 Hz
85 to 250 V AC, 45 to 65 Hz
11 to 40 V DC
Cable entry
Power supply and signal cables (inputs/outputs):
Cable entry M20 1.5 (8 to 12 mm/0.31 to 0.47 inch)
Threads for cable entries " NPT, G "
Connecting cable for remote version:
Cable entry M20 1.5 (8 to 12 mm/0.31 to 0.47 inch)
Threads for cable entries " NPT, G "
Cable specifications
47
84
Endress+Hauser
Promag 10
Technical data
Power consumption
Power consumption
20 to 28 V AC: <8 VA (incl. sensor)
85 to 250 V AC: <12 VA (incl. sensor)
11 to 40 V DC: <6 W (incl. sensor)
Switch-on current:
Max. 3.3 A (<5 ms) for 24 V DC
Max. 5.5 A (<5 ms) for 28 V DC
Max. 16 A (<5 ms) for 250 V DC
Power supply failure
Lasting min. cycle frequency: EEPROM saves measuring system data
50
10.1.6
Performance characteristics
Reference operating conditions

To DIN EN 29104 and VDI/VDE 2641:
Fluid temperature: +28 2 C (+82 4 F)
Ambient temperature: +22 2 C (+72 4 F)
Warm-up period: 30 minutes
Installation:
Inlet run >10 DN
Outlet run > 5 DN
Sensor and transmitter grounded.
The sensor is centered in the pipe.
Maximum measured error
Current output: plus typically 5 A
Pulse output: 0.5% o.r. 2 mm/s (o.r. = of reading)
Fluctuations in the supply voltage do not have any effect within the specified range.
[%]
2.5
2.0
0.5 %
1.5
1.0
0.5
0
0
0
2
5
4
10
6
15
20
8
25
10
30
[m/s]
v
32 [ft/s]
A0003200
Fig. 48:
Endress+Hauser
Max. measured error in % of reading
85
Technical data
Promag 10
Repeatability
Max. 0.2% o.r. 2 mm/s (o.r. = of reading)
10.1.7
Installation
Installation instructions
Any orientation (vertical, horizontal), restrictions and additional installation instructions
11
Inlet and outlet runs
If possible, install the sensor upstream from fittings such as valves, T-pieces, elbows, etc. The
following inlet and outlet runs must be observed in order to meet accuracy specifications (
14, 12):
Inlet run: 5 DN
Outlet run: 2 DN
Adapters
15
Length of connecting cable
The permitted length of connecting cable Lmax is determined by the fluid conductivity (
18, 16). A minimum conductivity of 50 S/cm is needed for all fluids.
The maximum connecting cable length is 10 m (32.81 ft) when empty pipe detection
(EPD 68) is switched on.
10.1.8
Environment
Ambient temperature range

Transmitter: 20 to +60 C (4 to +140 F)
! Note!
At ambient temperatures below 20 (4 F) the readability of the display may be impaired.
Sensor (flange material carbon steel): 10 to +60 C (+14 to +140 F)
"
Caution!
The permitted temperature range of the measuring tube lining may not be undershot or
overshot ( "Operating conditions: Process" "Medium temperature range").
Install the device in a shady location. Avoid direct sunlight, particularly in warm climatic
regions.
The transmitter must be mounted separate from the sensor if both the ambient and fluid
temperatures are high.
Storage temperature
The storage temperature corresponds to the operating temperature range of the measuring
transmitter and the appropriate measuring sensors.
"
Caution!
The measuring device must be protected against direct sunlight during storage in order to
avoid unacceptably high surface temperatures.
A storage location must be selected where moisture does not collect in the measuring
device. This will help prevent fungus and bacteria infestation which can damage the liner.
Standard: IP 67 (NEMA 4X) for transmitter and sensor
86
Endress+Hauser
Promag 10
Technical data
Shock and vibration resistance

Acceleration up to 2 g following IEC 600 68-2-6
CIP cleaning
"
Caution!
The maximum fluid temperature permitted for the device may not be exceeded.
CIP cleaning is possible:
Promag E (100 C / 212 F), Promag H/P
CIP cleaning is not possible:
Promag D/L/W
SIP cleaning
"
Caution!
The maximum fluid temperature permitted for the device may not be exceeded.
SIP cleaning is possible:
Promag H
SIP cleaning is not possible:
Promag D/E/L/P/W
Electromagnetic compatibility (EMC)
As per IEC/EN 61326 and NAMUR Recommendation NE 21
Emission: to limit value for industry EN 55011
10.1.9
Process
Medium temperature range

The permissible temperature depends on the lining of the measuring tube
Promag D
0 to +60 C (+32 to +140 F) for polyamide
Promag E
10 to +110 C (+14 to +230 F) for PTFE,
Restrictions see the following diagram
Endress+Hauser
87
Technical data
Promag 10
TA [F]
140
100
[C]
60
40
PTFE
20
0
0
-20
-40
-40
-40 -20
-40
20
40
60
100
80 100 120 140 160 180

200
300
[C]
TF
360 [F]
A0022937
Fig. 49:
Compact and remote version Promag E (TA = ambient temperature; TF = fluid temperature)
Promag H
Sensor:
DN 2 to 25 (1/12 to 1"): 20 to +150 C (4 to +302 F)
DN 40 to 100 (1 to 4"): 20 to +150 C (4 to +302 F)
Seals:
EPDM/Viton (FKM)/Kalrez: 20 to +150 C (4 to +302 F)
Promag L
0 to +80 C (+32 to +176 F) for hard rubber (DN 350 to 2400 / 14 to 90")
20 to +50 C (4 to +122 F) for polyurethane (DN 25 to 1200 / 1 to 48")
20 to +90 C (4 to +194 F) for PTFE (DN 25 to 300 / 1 to 12")
Promag P
40 to +130 C (40 to +266 F) for PTFE (DN 25 to 600 / 1 to 24"),
Restrictions see the following diagram
TA [F]
140
100
[C]
60
40
-
Esc
PTFE
20
0
0
-20
-40
-40
m
-40 -20
-40
20
40
100
60
80 100 120 140 160 180

200
300
[C]
TF
360 [F]
a0003449
Fig. 50:
Compact version Promag P with PTFE-lining
TA = ambient temperature; TF = fluid temperature

= light gray area temperature range from 1040 C (1440 F) valid for stainless steel version only
88
Endress+Hauser
Promag 10
Technical data
Promag W
0 to +80 C (+32 to +176 F) for hard rubber (DN 65 to 2000 / 2 to 78")
20 to +50 C (4 to +122 F) for polyurethane (DN 25 to 1000 / 1 to 48")
Conductivity
The minimum conductivity is 50 S/cm
Note!
Note that in the case of the remote version, the requisite minimum conductivity is also
influenced by the length of the connecting cable 18
Medium pressure range (nominal pressure)
Promag D
EN 1092-1 (DIN 2501)
PN 16
ASME B 16.5
Class 150
JIS B2220
10 K
Promag E
EN 1092-1 (DIN 2501)
PN 10 (DN 200 to 600 / 8 to 24")
PN 16 (DN 65 to 600 / 3 to 24")
PN 40 (DN 15 to 150 / to 2")
ASME B 16.5
Class 150 ( to 24")
JIS B2220
10 K (DN 50 to 300 / 2 to 12")
20 K (DN 15 to 40 / to 1")
Promag H
The permissible nominal pressure depends on the process connection and the seal:
PN 40, Class 150, 20 K Couplings, flanges (with O-ring seal)
PN 16 Welding nipple, couplings, clamp, flange (with aseptic gasket seal)
Promag L
EN 1092-1 (DIN 2501)
PN 6 (DN 350 to 2400 / 14 to 90")
PN 10 (DN 200 to 2400 / 8 to 90")
PN 16 (DN 25 to 300 / 1 to 12")
EN 1092-1, lap joint flange, stampel plate
PN 10 (DN 25 to 300 / 1 to 12")
ASME B16.5
Class 150 (1 to 24")
AWWA
Class D (28 to 90")
AS2129
Table E (350 to 1200 / 14 to 48")
AS4087
PN 16 (350 to 1200 / 14 to 48")
Endress+Hauser
89
Technical data
Promag 10
Promag P
EN 1092-1 (DIN 2501)
PN 10 (DN 200 to 600 / 8 to 24")
PN 16 (DN 65 to 600 / 3 to 24")
PN 25 (DN 200 to 600 / 8 to 24")
PN 40 (DN 25 to 150 / 1 to 6")
ASME B 16.5
Class 150 (1 to 24")
Class 300 (1 to 6")
JIS B2220
10 K (DN 50 to 300 / 2 to 12")
20 K (DN 25 to 300 / 1 to 12")
AS 2129
Table E (DN 25 / 1"), 50 / 2")
AS 4087
PN 16 (DN 50 / 2")
Promag W
EN 1092-1 (DIN 2501)
PN 6 (DN 350 to 2000 / 14 to 84")
PN 10 (DN 200 to 2000 / 8 to 84")
PN 16 (DN 65 to 2000 / 3 to 84")
PN 25 (DN 200 to 1000 / 8 to 40")
PN 40 (DN 25 to 150 / 1 to 6")
ASME B 16.5
Class 150 (1 to 24")
Class 300 (1 to 6")
AWWA
Class D (28 to 78")
JIS B2220
10 K (DN 50 to 300 / 2 to 12")
20 K (DN 25 to 300 / 1 to 12")
AS 2129
Table E (DN 80 / 3", 100 / 4", 150 to 1200 / 6 to 48")
AS 4087
PN 16 (DN 80 / 3", 100 / 4", 150 to 1200 / 6 to 48")
Pressure tightness
Promag D
Measuring tube: 0 mbar abs (0 psi abs) with a fluid temperature of 60 C (140 F)
Promag E (Measuring tube lining: PTFE)
Nominal diameter
Resistance of measuring tube lining to partial vacuum

Limit values for abs. pressure [mbar] ([psi]) at various fluid temperatures
25 C
80 C
77 F
90
[mbar]
100 C
176 F
110 C
212 F
[psi]
[mbar]
230 F
[mm]
[inch]
[psi]
[mbar]
[psi]
15
"
100
1.45
25
1"
100
1.45
32
100
1.45
40
1 "
100
1.45
50
2"
100
1.45
65
40
0.58
130
1.89
Endress+Hauser
Promag 10
Technical data
Nominal diameter

25 C
80 C
100 C
110 C
77 F
176 F
212 F
230 F
[mm]
[inch]
[mbar]
[psi]
80
3"
100
4"
125
135
1.96
150
6"
135
1.96
200
8"
200
2.90
250
10"
330
4.79
300
12"
400
5.80
350
14"
470
6.82
400
16"
540
7.83
450
18"
500
20"
600
24"
[mbar]
[psi]
[mbar]
[psi]
40
0.58
130
1.89
135
1.96
170
2.47
240
3.48
385
5.58
240
3.48
385
5.58
290
4.21
410
5.95
400
5.80
530
7.69
500
7.25
630
9.14
600
8.70
730
10.59
670
9.72
800
11.60
Partial vacuum is impermissible!
* No value can be quoted.
Promag H (Measuring tube lining: PFA)

Nominal diameter

25 C
80 C
100 C
130 C
150 C
180 C
[mm]
[inch]
77 F
176 F
212 F
266 F
302 F
356 F
2 to 100
1/12 to 4"
Promag L (Measuring tube lining: Polyurethane, Hard rubber)

Nominal diameter
[mm]
Measuring
tube lining

Limit values for abs. pressure [mbar] ([psi]) at various fluid
temperatures
[inch]
25 C
50 C
80 C
77 F
122 F
176 F
25 to 1200
1 to 48"
25 to 1200
1 to 48"
350 to 2400
14 to 90"
Hard rubber
Promag L (Measuring tube lining: PTFE)

Nominal diameter
Endress+Hauser

25 C
90 C
77 F
194 F
[mm]
[inch]
[mbar]
[psi]
[mbar]
[psi]
25
1"
32
40
1 "
50
2"
65
40
0.58
80
3"
40
0.58
100
4"
135
1.96
125
135
1.96
240
3.48
150
6"
135
1.96
240
3.48
91
Technical data
Promag 10
Nominal diameter

25 C
90 C
77 F
194 F
[mm]
[inch]
[mbar]
[psi]
[mbar]
[psi]
200
8"
200
2.90
290
4.21
250
10"
330
4.79
400
5.80
300
12"
400
5.80
500
7.25
Promag P (Measuring tube lining: PTFE)

Nominal diameter Resistance of measuring tube lining to partial vacuum
25 C
80 C
77 F
176 F
[mm]
[inch]
[mbar]
[psi]
25
1"
32
40
1 "
50
2"
100 C
212 F
130 C
150 C
180 C
266 F
302 F
356 F
[mbar]
[psi]
[mbar]
[psi]
100
1.45
100
1.45
100
1.45
100
1.45
65
40
0.58
130
1.89
80
3"
40
0.58
130
1.89
100
4"
135
1.96
170
2.47
125
135
1.96
240
3.48
385
5.58
150
6"
135
1.96
240
3.48
385
5.58
200
8"
200
2.90
290
4.21
410
5.95
250
10"
330
4.79
400
5.80
530
7.69
300
12"
400
5.80
500
7.25
630
9.14
350
14"
470
6.82
600
8.70
730
10.59
400
16"
540
7.83
670
9.72
800
11.60
450
18"
500
20"
600
24"
Partial vacuum is impermissible!
* No value can be quoted.
Promag W
Nominal diameter
[mm]
[inch]
25 to 1200
1 to 40"
50 to 2000
2 to 78"
Measuring tube Resistance of measuring tube lining to partial vacuum

lining
Limit values for abs. pressure [mbar] ([psi]) at various fluid
temperatures
25 C
50 C
80 C
100 C
130 C
150 C
180 C
77 F
122 F
176 F
212 F
266 F
302 F
356 F
Polyurethane
Hard rubber
Limiting flow
16
Pressure loss
No pressure loss if the sensor is installed in a pipe with the same nominal diameter.
Pressure losses for configurations incorporating adapters according to DIN EN 545
(see "Adapters" 15)
92
Endress+Hauser
Promag 10
Technical data
10.1.10 Mechanical construction

Design, dimensions
The dimensions and installation lengths of the sensor and transmitter can be found in the
"Technical Information" for the device in question. This document can be downloaded as a
PDF file from www.endress.com. A list of the "Technical Information" documents available is
provided in the "Documentation" section on 107.
Weight (SI units)
Promag D
Weight data in kg
Nominal diameter
[mm]
[inch]
25
1"
40
1 "
Compact version
Remote version (without cable)

Sensor
Transmitter
2.9
2.5
3.1
3.5
3.1
3.1
3.1
50
2"
4.3
3.9
65
2 "
5.1
4.7
3.1
80
3"
6.1
5.7
3.1
100
4"
8.8
8.4
3.1
Transmitter Promag (compact version): 1.8 kg (Weight data valid without packaging material)
Promag E
Weight data in kg
Nominal
diameter
Compact version
EN (DIN)
ASME
JIS
[mm]
[inch]
PN 6
PN 10
PN 16
PN 40
Class 150
10K
15
"
6.5
6.5
6.5
25
1"
7.3
7.3
7.3
32
8.0
7.3
40
1"
9.4
9.4
8.3
50
2"
10.6
10.6
9.3
65
12.0
11.1
80
3"
14.0
14.0
12.5
100
4"
16.0
16.0
14.7
125
21.5
21.0
150
6"
25.5
25.5
24.5
200
8"
45.0
46.0
45.0
41.9
250
10"
65.0
70.0
75.0
69.4
300
12"
70.0
81.0
110.0
72.3
350
14"
77.4
88.4
99.4
137.4
400
16"
89.4
104.4
120.4
168.4
450
18"
99.4
112.4
133.4
191.4
500
20"
114.4
132.4
182.4
228.4
600
24"
155.4
162.4
260.4
302.4
Transmitter (compact version): 1.8 kg

Weight data without packaging material
Endress+Hauser
93
Technical data
Promag 10
Weight data in kg
Nominal
diameter

Sensor
Transmitter
EN (DIN)
ASME
JIS
[mm]
[inch]
PN 6
PN 10
PN 16
PN 40
Class 150
10K
15
"
4.5
4.5
4.5
25
1"
5.3
5.3
5.3
32
6.0
5.3
40
1"
7.4
7.4
6.3
50
2"
8.6
8.6
7.3
65
10.0
9.1
80
3"
12.0
12.0
10.5
100
4"
14.0
14.0
12.7
125
19.5
19.0
150
6"
23.5
23.5
22.5
200
8"
43.0
44.0
43.0
39.9
250
10"
63.0
68.0
73.0
67.4
300
12"
68.0
79.0
108.0
70.3
350
14"
73.1
84.1
95.1
133.1
400
16"
85.1
100.1
116.1
164.1
450
18"
95.1
108.1
129.1
187.1
500
20"
110.1
128.1
178.1
224.1
600
24"
158.1
158.1
256.1
298.1
Wall-mount housing
6.0
Transmitter (remote version): 3.1 kg

Promag H
Weight data in kg
Nominal diameter
Compact version
[mm]
[inch]
DIN
Sensor
Transmitter
1/12"
3.6
3.1
1/8"
3.6
3.1
3/8"
3.6
3.1
15
"
3.7
1.9
3.1
25
1"
3.9
2.8
3.1
40
1 "
4.9
4.5
3.1
50
2"
7.4
7.0
3.1
65
2 "
7.9
7.5
3.1
80
3"
17.4
17.0
3.1
100
4"
16.9
16.5
3.1
Transmitter Promag (compact version): 1.8

(Weight data valid for standard pressure ratings and without packaging material)
94
Endress+Hauser
Promag 10
Technical data
Promag L
Weight data in kg
Compact version (including transmitter)1)
Nominal
diameter
[mm]
[inch]
25
1"
EN (DIN)
ASME/
AWWA
7.3
AS
7.9
1 "
8.0
40
1 "
9.0
7.5
50
2"
9.4
7.6
65
2 "
10.4
80
3"
12.4
12.8
100
4"
14.4
16.1
125
5"
15.9
150
6"
23.9
ASME / Class 150
32
24.4
70.7
300
12"
68.4
85.8
350
14"
77.4
88.4
375
15"
400
16"
89.4
104
450
18"
99.4
112
139
191
133
143
500
20"
114
132
174
228
182
182
600
24"
155
162
303
302
260
700
28"
288
266
750
30"
318
445
800
32"
240
315
364
383
503
190
240
49.6
75.1
100
103
137
99.4
99.4
105
124
168
120
120
367
Tabelle E
44.9
63.4
PN 16
43.4
PN 16
10"
PN 10
8"
250
PN 6
200
260
346
433
493
36"
308
393
456
470
702
690
40"
359
468
579
587
759
761
1050
42"
670
1200
48"
529
717
866
1237
54"
1400
784
1114
1274
AWWA / Class D
900
1000
901
1273
60"
1600
1058
1624
1872
1594
1650
66"
2131
1800
72"
1418
2107
2409
2568
2000
78"
1877
2630
2997
3113
84"
3755
2200
2512
3422
90"
4797
2400
2996
4094
Transmitter Promag (compact version): 3.1 kg

(Weight data valid without packaging material)
1)
Endress+Hauser
Lap joint flanges / welded flanges DN > 300 (12")
95
Technical data
Promag 10
Weight data in kg
Remote version (sensor plus sensor housing without cable)1)
Nominal
diameter
[mm]
[inch]
25
1"
EN (DIN)
ASME/
AWWA
5.3
AS
5.9
1 "
6.0
40
1 "
7.0
5.5
50
2"
7.4
5.6
65
2 "
8.4
80
3"
10.4
10.8
100
4"
12.4
14.1
22.4
125
5"
13.9
150
6"
21.9
ASME / Class 150
32
68.7
300
12"
66.4
83.8
350
14"
75.4
86.4
375
15"
102
400
16"
87.4
102
450
18"
97.4
110
139
189
131
141
500
20"
112
130
174
226
180
180
600
24"
153
160
303
300
258
700
28"
288
264
750
30"
316
443
800
32"
238
313
364
381
501
188
238
47.6
73.1
98
103
135
97.4
97.4
103
124
166
118
118
365
Tabelle E
42.9
61.4
PN 16
41.4
PN 16
10"
PN 10
8"
250
PN 6
200
258
344
431
491
36"
306
391
456
468
700
688
40"
357
466
579
585
757
759
1050
42"
668
1200
48"
527
715
866
54"
1400
782
1112
1274
AWWA / Class D
900
1000
899
1235
1271
60"
1600
1056
1622
1872
1592
1650
66"
2129
1800
72"
1416
2105
2409
2566
2000
78"
1875
2628
2997
3111
84"
3753
2200
2510
3420
90"
4795
2400
2994
4092
Transmitter Promag (remote version): 3.4 kg

1)
96
Endress+Hauser
Promag 10
Technical data
Weight data in kg
Compact version1)
Nominal diameter
[mm]
[inch]
Remote version (without cable)1)
EN (DIN)
Sensor EN (DIN)
Transmitter
25
1"
5.8
3.8
4.2
32
1 "
5.4
3.4
4.2
40
1 "
6.3
4.7
4.2
50
2"
5.4
3.4
4.2
65
2 "
6.2
4.2
4.2
125
5"
150
6"
200
7.2
5.2
4.2
7.7
4.2
13.2
11.2
4.2
17.2
15.2
4.2
8"
35.7
33.7
4.2
250
10"
54.2
52.2
4.2
300
12"
55.2
53.2
4.2
PN 10
3"
4"
PN 10
80
100
9.7

1)
Lap joint flanges, stamped plate
Promag P
Weight data in kg
Nominal
diameter
Sensor
EN (DIN) /
AS*
1"
32
1 "
40
1 "
JIS
5.7
PN 40
25

ASME/
AWWA
5.7
EN (DIN) /
AS*
5.7
6.4
5.7
7.8
6.7
7.8
JIS
5.3
PN 40
[mm] [inch]
Compact version
ASME/
AWWA
5.3
5.3
Transmitter
3.1
6.0
5.3
3.1
7.4
6.3
7.4
3.1
9.0
8.6
7.3
8.6
3.1
9.5
10.0
9.1
3.1
125
5"
150
6"
12.4
14.4
10.9
12.4
13.1
14.4
19.9
19.4
23.9
22.9
12.0
14.0
10.5
12.0
3.1
12.7
14.0
3.1
19.5
19.0
23.5
22.5
43.4
43
39.9
73.4
63
67.4
70.3
23.9
Class 150
3"
4"
Class 150
80
100
10K
7.7
10.4
PN 16
9.0
2 "
10K
2"
65
PN 16
50
3.1
23.5
3.1
43
3.1
73
3.1
43.4
40.3
10"
63.4
67.8
300
12"
68.4
70.7
108.4
68
108
3.1
350
14"
113.4
172.4
113
173
3.1
400
16"
133.4
203.4
133
203
3.1
450
18"
173.4
253.4
173
253
3.1
500
20"
173.4
283.4
173
283
3.1
600
24"
233.4
403.4
233
403
3.1
PN 10
8"
250
PN 10
200

* Flanges according to AS are only available for DN 25 and 50.
Endress+Hauser
97
Technical data
Promag 10
Promag W
Weight data in kg
Nominal
diameter
[mm] [inch]
Compact version

Sensor
EN (DIN) /
AS*
JIS
ASME/
AWWA
EN (DIN) /
AS*
JIS
ASME/
AWWA
Transmitter
5.7
5.3
5.3
5.3
3.1
6.0
5.3
3.1
40
1 "
7.8
6.7
7.8
7.4
6.3
7.4
3.1
50
2"
9.0
7.7
9.0
8.6
7.3
8.6
3.1
65
2 "
10.4
9.5
10.0
9.1
3.1
80
3"
12.4
10.9
12.4
12.0
10.5
12.0
3.1
100
4"
125
5"
150
200
23.9
22.9
8"
43.4
40.3
250
10"
63.4
300
12"
68.4
350
14"
400
16"
450
18"
500
20"
600
24"
700
28"
14.0
12.7
14.0
3.1
19.5
19.0
3.1
23.9
23.5
22.5
43.4
43
39.9
67.8
73.4
63
70.7
108.4
68
113.4
172.4
133.4
203.4
173.4
253.4
173.4
283.4
233.4
403.4
353.4
398.4
Class 150
6"
PN 16
Class 150
14.4
19.4
PN 10
PN 16
13.1
19.9
PN 10
14.4
10K
5.7
5.7
PN 40
5.7
6.4
10K
1"
1 "
PN 40
25
32
23.5
3.1
43
3.1
67.4
73
3.1
70.3
108
3.1
113
173
3.1
133
203
3.1
173
253
3.1
173
283
3.1
233
403
3.1
353
398
3.1
30"
458.4
458
3.1
800
32"
433.4
548.4
433
548
3.1
900
36"
573.4
798.4
573
798
3.1
1000
40"
698.4
898.4
698
898
3.1
1098.4
1098
3.1
848.4
1398.4
848
1398
3.1
1298.4
60"
1600
2198.4
1298
2698.4
1698.4
PN 6
54"
PN 6
1400
Class D
42"
48"
Class D
1200
2198
3.1
3.1
2698
3.1
1698
3.1
66"
3698.4
3698
3.1
1800
72"
2198.4
4098.4
2198
4098
3.1
78"
4598.4
4598
3.1
2000
2798.4
2798
3.1

*Flanges according to AS are only available for DN 80, 100, 150 to 400, 500 and 600
98
Endress+Hauser
Promag 10
Technical data
Weight (US units)

Promag D
Weight data in lbs
Nominal diameter
[mm]
Compact version
[inch]
Sensor
Transformer
25
1"
40
1 "
50
2"
80
3"
13
13
100
4"
19
19
Transmitter Promag (compact version): 3.9 lbs (Weight data valid without packaging material)
Promag E
Weight data in lbs
Nominal
diameter
Compact version

Sensor
ASME
ASME
Transmitter
[mm]
[inch]
Class 150
Class 150
15
"
14.3
9.92
25
1"
16.1
11.7
40
1"
20.7
16.3
50
2"
23.4
19.0
80
3"
30.9
26.5
100
4"
35.3
30.9
150
6"
56.2
51.8
200
8"
99.2
94.8
250
10"
165.4
161.0
300
12"
242.6
238.1
350
14"
303.0
293.5
400
16"
371.3
361.8
450
18"
422.0
412.6
500
20"
503.6
494.1
600
24"
666.8
657.3
Wall-mount housing
13.2
Transmitter: 4.0 lbs (compact version); 6.8 lbs (remote version)

Promag H
Weight data in lbs
Nominal diameter
Compact version
[mm]
[inch]
Sensor
1/12"
Transformer
7
1/8"
7
7
3/8"
15
"
25
1"
40
1 "
11
10
50
2"
16
15
65
2 "
17
17
80
3"
38
37
100
4"
37
36
Transmitter Promag (compact version): 3.9 lbs

Endress+Hauser
99
Technical data
Promag 10
Promag L (ASME/AWWA)
Weight data in lbs
Nominal diameter
Compact version1)
Remote version1)
ASME/AWWA
ASME/AWWA
25
1"
17.4
13
32
1 "
40
1 "
16.5
12.1
50
2"
16.8
12.3
65
2 "
80
3"
28.2
23.8
100
4"
35.5
31.1
125
5"
150
6"
53.8
49.4
200
8"
250
10"
300
12"
350
14"
302
375
15"
400
16"
370
366
450
18"
421
417
500
20"
503
498
600
24"
666
662
700
28"
587
582
750
30"
701
697
800
32"
845
840
900
36"
1036
1032
1000
40"
1294
1290
1050
42"
1477
1473
1200
48"
1987
1982
54"
1400
60"
166
221
2807
3515
105
161
216
298
AWWA / Class D
AWWA / Class D
109
ASME / Class 150
[inch]
ASME / Class 150
[mm]
2803
3510
1600
1650
66"
1800
72"
5662
5658
2000
78"
6864
6860
8275
4699
4694
84"
8280
2200
90"
10577
10573
2400

Transmitter Promag (remote version): 6.8 lbs
1)
100
Endress+Hauser
Promag 10
Technical data
Promag P (ASME/AWWA)
Weight data in lbs
Nominal diameter
Compact version
[mm]
[inch]
25
1"
13
Sensor
12
Transformer
7
40
1 "
17
16
50
2"
20
19
27
26
32
31
150
6"
53
52
200
8"
95
250
10"
161
300
12"
238
350
14"
380
381
400
16"
448
448
450
18"
559
558
500
20"
625
624
600
24"
889
889
96
162
239
Class 150
3"
4"
Class 150
80
100

Promag W (ASME/AWWA)
Weight data in lbs
Nominal diameter
[mm]
Compact version
[inch]
Sensor
Transformer
13
12
17
16
50
2"
20
19
80
3"
27
26
100
4"
32
31
150
6"
53
52
200
8"
250
10"
300
12"
350
14"
380
400
16"
450
161
238
381
448
448
18"
559
558
500
20"
625
624
600
24"
889
889
700
28"
878
878
30"
1011
1010
800
32"
1209
1208
900
36"
1760
1760
1000
40"
1981
1980
42"
2422
2421
1200
48"
3083
54"
4847
4847
60"
5950
5949
66"
8155
8154
1800
72"
9037
9036
78"
10139
10139
162
239
3083
Class D
95
Class D
96
Class 150
1"
1 "
Class 150
25
40

Endress+Hauser
101
Technical data
Promag 10
Material
Promag D
Transmitter housing: powder-coated die-cast aluminum
Sensor housing: powder-coated die-cast aluminum
Measuring tube: polyamide, O-rings EPDM
(Drinking water approvals: WRAS BS 6920, ACS, NSF 61, KTW/W270)
Electrodes: 1.4435 (316, 316L)
Ground disks: 1.4301 (304)
Promag E
Sensor housing
DN 15 to 300 ( to 12"): powder-coated die-cast aluminum
DN 350 to 600 (14 to 24"): with protective lacquering
Measuring tube
DN 300 (12"): stainless steel 1.4301 (304) or 1.4306 (304L) (with Al/Zn protective
coating)
DN 350 (14"): stainless steel 1.4301 (304) or 1.4306 (304L) (with protective
lacquering)
Electrodes: 1.4435 (316, 316L), Alloy C22
Flanges (with protective lacquering)
EN 1092-1 (DIN2501): RSt37-2 (S235JRG2); Alloy C22; Fe 410W B
ASME: A105
JIS: RSt37-2 (S235JRG2); HII
Seals: to DIN EN 1514-1
Ground disks: 1.4435 (316, 316L) or Alloy C22
Promag H
Window material: glass or polycarbonate
Sensor housing: stainless steel 1.4301 (304)
Wall mounting kit: stainless steel 1.4301 (304)
Measuring tube: stainless steel 1.4301 (304)
Liner: PFA (USP class VI; FDA 21 CFR 177.1550: 3A)
Electrodes: 11.4435 (316, 316L) (optional: Alloy C22, tantalum, platinum)
Flanges: connections generally made of 1.4404 (316L)
Seals
DN 2 to 25: O-ring (EPDM, Viton, Kalrez), gasket seal (EPDM*, Viton, Silicone*)
DN 40 to 100: gasket seal (EPDM*, Silicone*)
* = USP class VI; FDA 21 CFR 177.2600: 3A
Ground rings: 1.4435 (316, 316L) (optional: Alloy C22)
Promag L
Transmitter housing:
Compact housing: powder-coated die-cast aluminum
Wall-mounted housing: powder-coated die-cast aluminum
102
Endress+Hauser
Promag 10
Technical data
Sensor housing
DN 25 to 300 (1 to 12"): powder-coated die-cast aluminum
DN 350 to 1200 (14 to 48"): with protective lacquering
Measuring tube:
DN 300 (12"); stainless steel 1.4301 (304) or 1.4306 (304L)
DN 350 (14"); stainless steel 202 or 304
Flange
EN 1092-1 (DIN 2501): DN 300: 1.4306; 1.4307; 1.4301 (304); 1.0038 (S235JRG2)
EN 1092-1 (DIN 2501): DN 350: A105; 1.0038 (S235JRG2)
AWWA: A181/A105; 1.0425 (316L) (P265GH); 1.0044 (S275JR)
AS 2129: A105; 1.0345 (P235GH); 1.0425 (316L) (P265GH); 1.0038 (S235JRG2);
FE 410 WB
AS 4087: A105; 1.0425 (316L) (P265GH); 1.0044 (S275JR)
Promag P/W
Sensor housing
DN 25 to 300: powder-coated die-cast aluminum
DN 350 to 2000: with protective lacquering
Measuring tube
DN 300: stainless steel 1.4301 (304) or 1.4306 (304L)
(Flange material: carbon steel with Al/Zn protective coating)
DN 350: stainless steel 1.4301 (304) or 1.4306 (304)
(Flange material: carbon steel with protective lacquering)
Flange
EN 1092-1 (DIN2501): RSt37-2 (S235JRG2); Alloy C22; FE 410 WB
(DN 300: with Al/Zn protective coating; DN 350 with protective lacquering)
ASME: A105
(DN 300 with Al/Zn protective coating; DN 350 with protective lacquering)
AWWA (only Promag W): 1.0425 (with protective lacquering)
JIS: RSt37-2 (S235JRG2); HII; 1.0425
AS 2129
(DN 25, 80, 100, 150 to 1200) A105 or RSt37-2 (S235JRG2)
(DN 50, 80, 350, 400, 500) A105 or St44-2 (S275JR)
AS 4087: A105 or St44-2 (S275JR)
Material load diagram
The material load diagrams (pressure-temperature graphs) for the process connections are
to be found in the "Technical Information" documents of the device in question:
List of supplementary documentation 107.
Endress+Hauser
103
Technical data
Promag 10
Fitted electrodes
Promag D
2 measuring electrodes for signal detection
Promag E/L/P/W
1 EPD electrode for empty pipe detection
1 reference electrode for potential equalization
Promag H
1 EPD electrode for empty pipe detection (apart from DN 2 to 15)
Process connections
Promag D
Wafer version without process connections
Promag E
Flange connection:
EN 1092-1 (DIN 2501), DN 300 (12") form A, DN 350 (14") form B
(Dimensions to DIN 2501, DN 65 PN 16 and DN 600 (24") PN 16 exclusively to
EN 1092-1)
ASME B16.5
JIS B2220
Promag H
With O-ring:
Flange EN (DIN), ASME, JIS
External thread
With gasket seal:
Weld nipple DIN 11850, ODT/SMS
TriClamp L14 AM7
Threaded joint DIN 11851, DIN 11864-1, SMS 1145
Flange DIN 11864-2
Promag L
Flange connection:
EN 1092-1 (DIN 2501)
DN 300 (12") = form A
DN 350 (14") = form B
ASME B16.5
AWWA C207
AS
Promag P/W
Flange connections:
EN 1092-1 (DIN 2501)
DN 300 = form A
DN 350 = flat face
DN 65 PN 16 and DN 600 PN 16 only as per EN 1092-1
104
Endress+Hauser
Promag 10
Technical data
ASME
AWWA (only Promag W)
JIS
AS
Surface roughness
All data relate to parts in contact with fluid.
Liner PFA: 0.4 m (15 in)
Electrodes 1.4435 (316, 316L), Alloy C22: 0.3 to 0.5 m (12 to 20 in)
Process connection made of stainless-steel (Promag H):
with O-ring seal: 1.6 m (63 in)
with aseptic gasket seal: 0.8 m (31.5 in)
optional: 0.38 m (15 in)
10.1.11 Human interface

Display elements
Liquid crystal display: unilluminated, two-line, 16 characters per line
Display (operating mode) preconfigured: volume flow and totalizer status
1 totalizer
Note!
At ambient temperatures below 20 (4 F) the readability of the display may be impaired.
Operating elements
Local operation with three keys ()
Remote operation
Operation via HART protocol and FieldCare
10.1.12 Certificates and approvals

CE mark
The measuring system is in conformity with the statutory requirements of the EC Directives.
Endress+Hauser confirms successful testing of the device by affixing to it the CE mark.
C-tick mark
The measuring system meets the EMC requirements of the Australian Communications and
Media Authority (ACMA)
Ex approval
Information about currently available Ex versions (ATEX, FM, CSA, IECEx, NEPSI etc.) can be
supplied by your Endress+Hauser Sales Center on request. All explosion protection data are
given in a separate documentation which is available upon request.
Sanitary compatibility
Promag D/E/L/P/W
No applicable approvals or certification
Endress+Hauser
105
Technical data
Promag 10
Promag H
3A authorization and EHEDG-certified
Seals: in conformity with FDA (except Kalrez seals)
Drinking water approval
Promag D/L/W
WRAS BS 6920
ACS
NSF 61
KTW/W270
Promag E/H/P
No drinking water approval
Pressure Equipment Directive
Promag D/L
No pressure measuring device approval
Promag E/H/P/W
The devices can be ordered with or without a PED approval. If a device with a PED approval
is required, this must be explicitly stated in the order. For devices with nominal diameters
less than or equal to DN 25 (1"), this is neither possible nor necessary.
With the PED/G1/x (x = category) marking on the sensor nameplate, Endress+Hauser
confirms compliance with the "Essential Safety Requirements" specified in Annex I of the
Pressure Equipment Directive 97/23/EC.
Devices bearing this marking (PED) are suitable for the following types of medium:
Media in Group 1 and 2 with a vapor pressure greater than, or smaller and equal to 0.5 bar
(7.3 psi)
Devices not bearing this marking (PED) are designed and manufactured according to good
engineering practice. They meet the requirements of Art.3 Section 3 of the Pressure
Equipment Directive 97/23/EC. The range of application is indicated in tables 6 to 9 in
Annex II of the Pressure Equipment Directive.
Other standards and guidelines
EN 60529:
Degrees of protection by housing (IP code).
EN 61010-1
Safety requirements for electrical equipment for measurement, control and laboratory use
IEC/EN 61326
Electromagnetic compatibility (EMC requirements)
ASME/ISA-S82.01
Safety Standard for Electrical and Electronic Test, Measuring, Controlling and related
Equipment - General Requirements. Pollution degree 2, Installation Category II.
CAN/CSA-C22.2 (No. 1010.1-92)
Safety requirements for Electrical Equipment for Measurement and Control and
Laboratory Use. Pollution degree 2, Installation Category I.
106
Endress+Hauser
Promag 10
Technical data
10.1.13 Ordering information

Detailed ordering information is available from the following sources:
In the Product Configurator on the Endress+Hauser website: www.endress.com Select
country Instruments Select device Product page function: Configure this product
From your Endress+Hauser Sales Center: www.endress.com/worldwide
Note!
Product Configurator - the tool for individual product configuration
Up-to-the-minute configuration data
Depending on the device: Direct input of measuring point-specific information such as
measuring range or operating language
Automatic verification of exclusion criteria
Automatic creation of the order code and its breakdown in PDF or Excel output format
Ability to order directly in the Endress+Hauser Online Shop
10.1.14 Accessories
Various accessories, which can be ordered separately from Endress+Hauser, are available for
the transmitter and the sensor. 70
Your Endress+Hauser service organization can provide detailed information on the specific
order codes on request.
10.1.15 Documentation
Flow measuring technology (FA00005D/06)
Technical Information Promag 10D (TI00081D/06)
Technical Information Promag 10E (TI01160D/06)
Technical Information Promag 10H (TI00095D/06)
Technical Information Promag 10L(TI00100D/06)
Technical Information Promag 10P (TI00094D/06)
Technical Information Promag 10W (TI00093D/06)
Endress+Hauser
107
SENSOR TYPE
( 131)
SERIAL NUMBER
( 131)
SW REV.
( 131)
AMPLIFIER VERS.
( 131)
VALUE SIM. MEASUR.

( 131)
SIM. MEASURAND
( 130)
SIM. FAILSAFE
( 130)
SENSOR VERSION
( 131)
SYSTEM RESET
( 130)
ALARM DELAY
( 130)
FAILSAFE MODE
( 129)
SIMULAT. SYSTEM
( 131)
ZERO POINT
( 127)
K-FACTOR
( 127)
CALIBRATION DATE
( 127)
SUPERVISION
( 129)
POS. ZERO-RET.
( 125)
MEASURING MODE
( 124)
INSTALLATION
DIRECTION ( 124)
SENSOR DATA
( 127)
EPD ADJ.
( 123)
EPD
( 122)
LOW FLOW CUT OFF

( 122)
SYSTEM PARAM.
( 124)
BUS ADDRESS
( 121)
TAG DESCR.
( 121)
TAG NAME
( 121)
PROCESS PARAM.
( 122)
SWITCH-OFF POINT
( 118)
SWITCH-ON POINT
( 117)
ASSIGN STATUS
( 117)
COMMUNICATION
( 121)
PULSE WIDTH
( 116)
PULSE VALUE
( 116)
OPERATING MODE
( 116)
PULSE/STATUS OUTP.
( 116)
TIME CONSTANT
( 115)
VALUE 20 mA
( 115)
CURRENT RANGE
( 114)
CURRENT OUTPUT
( 114)
RESET TOTALIZ.
( 113)
OVERFLOW
( 113)
SUM
( 113)
TOTALIZER
( 113)
TEST DISPLAY
( 112)
CONTRAST LCD
( 112)
FORMAT
( 112)
USER INTERFACE
( 112)
DEFINE PRIVATE
CODE ( 111)
ACCESS CODE
( 111)
LANGUAGE
( 111)
OPERATION
( 111)
FORMAT DATE/TIME
( 110)
UNIT VOLUME
( 109)
SYSTEM UNITS
( 109)
Functions
UNIT. VOL. FLOW

( 109)
108
Function groups
MEASURING PERIOD
( 128)
MANUFACTURER ID
( 121)
EPD ELECTRODE
( 128)
DEVICE ID
( 121)
11
Appendix
11.1
Illustration of the function matrix
SELF CHECKING
( 130)
NOMINAL DIAMETER
( 127)
SYSTEM DAMP.
( 126)
HART WRITE
PROTECT. ( 121)
OUTPUT SIGNAL
( 117)
Appendix
Promag 10
Endress+Hauser
Promag 10
Appendix
11.2
Group SYSTEM UNITS

Functional description SYSTEM UNITS
Use this function group to select the unit required and displayed for the measured variable.
UNIT VOLUME FLOW
Use this function to select the unit required and displayed for the volume flow.
The unit you select here is also valid for:
Volume flow display
Current output
Switch points (limit value for volume flow, flow direction)
Low flow cut off
Options:
Metric:
Cubic centimeter cm3/s; cm3/min; cm3/h; cm3/day
Cubic decimeter dm3/s; dm3/min; dm3/h; dm3/day
Cubic meter m3/s; m3/min; m3/h; m3/day
Milliliter ml/s; ml/min; ml/h; ml/day
Liter l/s; l/min; l/h; l/day
Hectoliter hl/s; hl/min; hl/h; hl/day
Megalith Ml/s; Ml/min; Ml/h; Ml/day
US:
Cubic centimeter cc/s; cc/min; cc/h; cc/day
Acre foot af/s; af/min; af/h; af/day
Cubic foot ft3/s; ft3/min; ft3/h; ft3/day
Fluid ounce oz f/s; oz f/min; oz f/h; oz f/day
Gallon gal/s; gal/min; gal/h; gal/day
Kilo gallons kgal/s; kgal/min; kgal/h; kgal/day
Million gallons Mgal/s; Mgal/min; Mgal/h; Mgal/day
Barrel (normal fluids: 31.5 gal/bbl) bbl/s; bbl/min; bbl/h; bbl/day
Barrel (beer: 31.0 gal/bbl) bbl/s; bbl/min; bbl/h; bbl/day
Barrel (petrochemicals: 42.0 gal/bbl) bbl/s; bbl/min; bbl/h; bbl/day
Barrel (filling tanks: 55.0 gal/bbl) bbl/s; bbl/min; bbl/h; bbl/day
Imperial:
Gallon gal/s; gal/min; gal/h; gal/day
Mega gallon Mgal/s; Mgal/min; Mgal/h; Mgal/day
Barrel (beer: 36.0 gal/bbl) bbl/s; bbl/min; bbl/h; bbl/day
Barrel (petrochemicals: 34.97 gal/bbl) bbl/s; bbl/min; bbl/h; bbl/day
Factory setting:
Depends on nominal diameter and country
(dm3/min to m3/h or US-gal/min),
corresponding to the full scale value unit factory setting 132
UNIT VOLUME
Use this function to select the unit required and displayed for the volume.
The unit you select here is also valid for:
Totalizer status display
Totalizer unit
Pulse value (e.g. m3/p)
Options:
Metric cm3; dm3; m3; ml; l; hl; Ml
US cc; af; ft3; oz f; gal; Mgal; bbl (normal fluids); bbl (beer); bbl (petrochemicals);
bbl (filling tanks)
Imperial gal; Mgal; bbl (beer); bbl (petrochemicals)
Factory setting:
Depends on nominal diameter and country (dm3 to m3 or US-gal
corresponding to the totalizer unit factory setting. 132
Endress+Hauser
109
Appendix
Promag 10
Functional description SYSTEM UNITS

FORMAT DATE/TIME
Use this function to select the format for the date and the time.
The unit you select here is also valid for displaying the current calibration date
(function CALIBRATION DATE on 127
Options:
DD.MM.YY 24H
MM/DD/YY 12H A/P
DD.MM.YY 12H A/P
MM/DD/YY 24H
Factory setting:
DD.MM.YY 24H (SI units)
MM/DD/YY 12H A/P (US units)
110
Endress+Hauser
Promag 10
Appendix
11.3
Group OPERATION
Functional description OPERATION
LANGUAGE
Use this function to select the language for all texts, parameters and messages
shown on the local display.
Options:
ENGLISH
DEUTSCH
FRANCAIS
ESPANOL
ITALIANO
Factory setting:
Depends on country, see factory setting 132
Note!
If you press the keys simultaneously at startup, the language defaults to
"ENGLISH".
ACCESS CODE
All data of the measuring system are protected against inadvertent change.
Programming is disabled and the settings cannot be changed until a code is entered
in this function. If you press the P keys in any function, the measuring system
automatically goes to this function and the prompt to enter the code appears on the
display (when programming is disabled).
You can activate programming by entering your private code (factory setting = 10,
see also the subsequent DEFINE PRIVATE CODE function)
User input:
Max. 4-digit number: 0 to 9999
Note!
The programming levels are disabled if you do not press the operating elements
within 60 seconds following automatic return to the HOME position.
You can also disable programming in this function by entering any number (other
than the defined private code).
The Endress+Hauser service organization can be of assistance if you mislay your
personal code.
DEFINE PRIVATE
CODE
Use this function to enter a personal code to enable programming.

User input:
0 to 9999 (max. 4-digit number)
Factory setting:
10
Note!
This function only appears if the private code was entered in the ACCESS CODE
function.
Programming is always enabled with the code "0".
Programming has to be enabled before this code can be changed.
When programming is disabled this function is not available, thus preventing
others from accessing your personal code.
Endress+Hauser
111
Appendix
Promag 10
11.4
USER INTERFACE
Functional description USER INTERFACE
FORMAT
Use this function to define the maximum number of places after the decimal point
displayed for the reading in the main line.
Options:
XXXXX.
XXXX.X
XXX.XX
XX.XXX
X.XXXX
Factory setting:
X.XXXX
Note!
Note that this setting only affects the reading as it appears on the display, it has
no influence on the accuracy of the system's calculations.
The places after the decimal point as computed by the measuring device cannot
always be displayed, depending on this setting and the engineering unit. In such
instances an arrow appears on the display between the measuring value and the
engineering unit (e.g. 1.2 l/h), indicating that the measuring system is
computing with more decimal places than can be shown on the display.
CONTRAST LCD
Use this function to optimize display contrast to suit local operating conditions.
User input:
10 to 100%
Factory setting:
50%
TEST DISPLAY
Use this function to test the operability of the local display and its pixels.
Options:
OFF
ON
Factory setting:
OFF
Test sequence:
1. Start the test by selecting ON.
2. All pixels of the main line and additional line are darkened for minimum
0.75 seconds.
3. The main line and additional line show an "8" in each field for minimum
0.75 seconds.
4. The main line and additional line show a "0" in each field for minimum 0.75
seconds.
5. The main line and additional line show nothing (blank display) for minimum
0.75 seconds.
When the test completes the local display returns to its initial state and the setting
changes to "OFF".
112
Endress+Hauser
Promag 10
Appendix
11.5
Group TOTALIZER
Functional description TOTALIZER
SUM
The total for the totalizer's measured variable aggregated since measuring
commenced appears on the display.
This value can be positive or negative, depending on:
Flow direction
and/or
Setting in the MEASURING MODE function 124
Display:
Max. 6-digit floating-point number, incl. sign and unit (e.g. 15467.4 m3)
Note!
The totalizer's response to faults is defined in the central "FAILSAFE MODE"
function 129.
The unit of the totalizer is defined in the UNIT VOLUME function 109.
OVERFLOW
The total for the totalizer's overflow aggregated since measuring commenced
appears on the display.
Total flow quantity is represented by a floating-point number consisting of max. 7
digits. You can use this function to view higher numerical values (>9,999,999) as
overflows. The effective quantity is thus the total of the OVERFLOW function plus
the value displayed in the SUM function.
Example:
Reading for 2 overflows: 2 E7 dm3 (= 20,000,000 dm3)
The value displayed in the function "SUM" = 196,845 dm3
Effective total quantity = 20,196,845 dm3
Display:
Integer with exponent, including sign and unit, e.g. 2 E7 dm3
RESET TOTALIZER
Use this function to reset the sum and the overflow of the totalizer to "zero" (=
RESET).
Options:
NO
YES
Factory setting:
NO
Endress+Hauser
113
Appendix
Promag 10
11.6
Group CURRENT OUTPUT

Functional description CURRENT OUTPUT
Note!
The functions of the CURRENT OUTPUT group are only available if the "0" value was entered in the BUS
ADDRESS function 121.
CURRENT RANGE
Use this function to specify the current range. You can configure the current output
either in accordance with the NAMUR recommendation (max. 20.5 mA) or for a
maximum drive of 25 mA.
Options:
OFF
4-20 mA (25 mA)
4-20 mA (25 mA) HART
4-20 mA NAMUR
4-20 mA HART NAMUR
4-20 mA US
4-20 mA HART US
Factory setting:
4-20 mA HART NAMUR
Current range, work range and signal on alarm level
I [mA]
o
20
m
n
p
A
OFF
4 mA
4-20 mA (25 mA)
4 - 24 mA
25
4-20 mA (25 mA) HART
4 - 24 mA
25
4-20 mA NAMUR
3,8 - 20,5 mA
3,5
22,6
4-20 mA HART NAMUR
3,8 - 20,5 mA
3,5
22,6
4-20 mA US
3,9 - 20,8 mA
3,75
22,6
4-20 mA HART US
3,9 - 20,8 mA
3,75
22,6
A0005392
A = Work range
m = Work range
n = Lower signal on alarm level
o = Upper signal on alarm level
p = Scaled full scale value
Q = Flow
Note!
If the measured value is outside the measuring range (defined in the
VALUE 20 mA function 115), a notice message is generated.
The current output's response to faults is defined in the central FAILSAFE MODE
function 129.
114
Endress+Hauser
Promag 10
Appendix
Functional description CURRENT OUTPUT

VALUE 20 mA
Use this function to assign the 20 mA current a full scale value. Positive and
negative values are permitted. The required measuring range is defined by defining
the VALUE 20 mA .
In the SYMMETRY measuring mode 124, the value assigned applies to both
flow directions; in the STANDARD measuring mode it applies only to the flow
direction selected.
User input:
5-digit floating-point number, with sign
Factory setting:
Depends on nominal diameter and country, [value] / [dm3m3 or US-galUSMgal]
Corresponds to the factory setting for the full scale value 132
Note!
The appropriate unit is taken from the SYSTEM UNITS group 109.
The value for 4 mA always corresponds to the zero flow (0 [unit]).
This value is fixed and cannot be edited.
TIME CONSTANT
Use this function to enter a time constant defining how the current output signal
reacts to severely fluctuating measured variables, either very quickly (enter a low
time constant) or with damping (enter a high time constant).
User input:
Fixed-point number 0.01 to 100.00 s
Factory setting:
1.00 s
Endress+Hauser
115
Appendix
Promag 10
11.7
Group PULSE/STATUS OUTPUT

Functional description PULSE/STATUS OUTPUT
OPERATING MODE
Configuration of the output as a pulse or status output. The functions available in

this function group vary, depending on which option you select here.
Options:
OFF
PULSE
STATUS
Factory setting:
PULSE
PULSE VALUE
Note!
This function is not available unless the PULSE setting was selected in the
OPERATING MODE function.
Use this function to define the flow at which a pulse is triggered. These pulses can
be totaled by an external totalizer, and the total flow quantity since measuring
started can be registered in this way. In the SYMMETRY measuring mode 124,
the value assigned applies to both flow directions; in the STANDARD measuring
mode it applies only to the positive flow direction.
User input:
5-digit floating-point number, [unit]
Factory setting:
Depends on nominal diameter and country, [value] [dm3m3 or US-gal] / pulse;
Corresponds to the factory setting for the pulse value 132
Note!
The appropriate unit is taken from the SYSTEM UNITS group.
PULSE WIDTH
Note!
Use this function to enter the maximum pulse width of the output pulses.
User input:
5 to 2000 ms
Factory setting:
100 ms
Pulse output is always with the pulse width (B) entered in this function. The pauses
(P) between the individual pulses are automatically configured. However, they must
at least correspond to the pulse width (B = P).
transistor
transistor
B< P
conducting
B= P
conducting
nonconducting
nonconducting
P
t
A0001233-en
P = Intervals between the individual pulses

B = Pulse width entered (the illustration applies to positive pulses)
"
Caution!
Buffering (pulse memory) takes place if the number of pulses is too large to output
the pulses with the selected pulse width (see PULSE VALUE function on 116).
The system error message RANGE PULSE is displayed if more pulses are in the pulse
memory than can be output in 4 seconds.
Note!
When selecting the pulse width, choose a value that can still be processed by a
connected counter (e.g. mechanical counter, PLC etc.).
The pulse output's response to faults is defined in the central FAILSAFE MODE
function 129.
116
Endress+Hauser
Promag 10
Appendix

OUTPUT SIGNAL
Note!
Use this function to configure the output in such a way that it matches an external
counter, for example. Depending on the application, you can select the direction of
the pulses here.
Options:
PASSIVE - POSITIVE
PASSIVE - NEGATIVE
Factory setting:
PASSIVE - NEGATIVE
ASSIGN STATUS
OUTPUT
Note!
This function is not available unless the STATUS setting was selected in the
Configuration of the status output.
Options:
ON (operation)
FAULT MESSAGE
NOTICE MESSAGE
FAULT MESSAGE or NOTICE MESSAGE
EPD (empty pipe detection, only if active)
FLOW DIRECTION
VOLUME FLOW LIMIT VALUE
Factory setting:
FAULT MESSAGE
Note!
The behavior of the status output is a normally closed behavior, in other words
the output is closed (trASMEstor conductive) when normal, error-free measuring
is in progress.
It is very important to read and comply with the information on the switching
characteristics of the status output 120.
SWITCH-ON POINT
Note!
This function is not available unless LIMIT VALUE or FLOW DIRECTION was
selected in the ASSIGN STATUS OUTPUT function.
Use this function to assign a value to the switch-on point (status output pulls up).
The value can be equal to, greater than or less than the switch-off point.
Positive and negative values are permitted.
User input:
Factory setting:
0 [unit]
Note!
Only the switch-on point is available for flow direction output (no switch-off
point). If you enter a value not equal to the zero flow (e.g. 5), the difference
between the zero flow and the value entered corresponds to half the switchover
hysteresis.
Endress+Hauser
117
Appendix
Promag 10

SWITCH-OFF POINT
Note!
This function is not available unless LIMIT VALUE was selected in the ASSIGN
STATUS OUTPUT function.
Use this function to assign a value to the switch-off point (status output drops off).
The value can be equal to, greater than or less than the switch-on point.
Positive and negative values are permitted.
User input:
Factory setting:
0 [unit]
Note!
If SYMMETRY is selected in the MEASURING MODE function and values with
different signs are entered for the switch-on and switch-off points, the notice
message "INPUT RANGE EXCEEDED" appears.
118
Endress+Hauser
Promag 10
Appendix
11.7.1
Information on the response of the status output
General
If you have configured the status output for "LIMIT VALUE" or "FLOW DIRECTION", you can
configure the requisite switch points in the SWITCH-ON POINT and SWITCH-OFF POINT
functions. When the measured variable in question reaches these predefined values, the
status output switches as shown in the illustrations below.
Status output configured for flow direction
Switch-off point/switch-on point
-Q
-1
+1
b
A0001236
a = Status output conductive

b = Status output not conductive
The value you entered in the function SWITCH-ON POINT defines the switch point for the
positive and negative directions of flow. If, for example, the switch point entered is = 1 m/
h, the status output switches off at 1 m/h (not conductive) and switches on again at +1
m/h (conductive). Set the switch point to 0 if your process calls for direct switchover (no
switching hysteresis). If low flow cut off is used, it is advisable to set hysteresis to a value
greater than or equal to the low flow cut off rate.
Status output configured for limit value
The status output switches as soon as the measured variable undershoots or overshoots a
defined switch point.
Application: monitoring flow or process-related boundary conditions.
A
m
B
n
m
o
C
n
n
o
t
A0001235
A = Maximum safety:
m SWITCH-OFF POINT > n SWITCH-ON POINT
B = Minimum safety:
m SWITCH-OFF POINT < n SWITCH-ON POINT
C = Minimum safety:
m SWITCH-OFF POINT = n SWITCH-ON POINT (this configuration should be avoided)
o = Relay de-energized
Endress+Hauser
119
Appendix
Promag 10
11.7.2
Switching behavior of the status output
Function
State
ON (operation)
System in measuring mode
Open collector behavior

(TrASMEstor)
conductive
XXX.XXX.XX
Esc
A0001237
System not in measuring

mode
(power supply failed)
not conductive
XXX.XXX.XX
Esc
Fault message
System OK
A0001239
conductive
XXX.XXX.XX
Esc
A0001237
(System error or process

error) fault Response to
error, outputs/inputs and
totalizers
Notice message
System OK
not conductive
XXX.XXX.XX
Esc
A0001239
conductive
XXX.XXX.XX
Esc
A0001237

error) Notice
Continuation of measuring
not conductive
XXX.XXX.XX
Esc
Fault message
or
notice message
System OK
A0001239
conductive
XXX.XXX.XX
Esc
A0001237

error) Fault Response to
error or
Notice Continuation of
measuring
Empty pipe
detection
(EPD)
not conductive
XXX.XXX.XX
Esc
A0001239
Measuring tube full
conductive
Measuring tube partially

filled / empty measuring
tube
not conductive
Forwards
conductive
A0001237
A0001239
Flow direction
A0001241
Backwards
A0001237
not conductive
A0001239
A0001242
Volume flow limit

value
Limit value not overshot or

undershot
conductive
A0001237
A0001243
Limit value overshot or

undershot
not conductive
A0001239
A0001244
120
Endress+Hauser
Promag 10
Appendix
11.8
Group COMMUNICATION
Functional description COMMUNICATION
Note!
The communication group is only visible if the HART option was selected in the CURRENT RANGE
function.
TAG NAME
Use this function to enter a tag name for the measuring device. You can edit and
read this tag name at the local display or via the HART protocol.
User input:
Max. 8-character text, permitted characters are: A-Z, 0-9, +,-, underscore, space,
period
Factory setting:
"_ _ _ _ _ _ _ _" (no text)
TAG DESCRIPTION
Use this function to enter a tag description for the measuring device. You can edit
and read this tag description at the local display or via the HART protocol.
User input:
Max. 16-character text, permitted characters are: A-Z, 0-9, +,-, underscore, space,
period
Factory setting:
"_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _" (no text)
BUS ADDRESS
Use this function to define the address for the exchange of data with the HART
protocol.
User input:
0 to 15
Factory setting:
0
Note!
Addresses 1 to 15: a constant 4 mA current is applied.
HART WRITE
PROTECTION
Use this function to activate HART write protection.

Options:
OFF = function can be edited/read via the HART protocol
ON = HART protocol write-protected (only readable)
Factory setting:
OFF
MANUFACTURER ID
Use this function to view the manufacturer ID in decimal numerical format.

Display:
Endress+Hauser
17 ( 11 hex) for Endress+Hauser
DEVICE ID
Use this function to view the device ID in hexadecimal numerical format.

Display:
45 hex ( 69 dec) for Promag 10
Endress+Hauser
121
Appendix
Promag 10
11.9
Group PROCESS PARAMETER

Functional description PROCESS PARAMETER
SWITCH-ON POINT
LOW FLOW CUT OFF
Use this function to enter the switch-on point for low flow cut off.
Low flow cut off is active if the value entered is not equal to 0. The sign of the flow
value is highlighted on the display to indicate that low flow cut off is active.
User input:
Factory setting:
Depends on nominal diameter and country, [value] / [dmm or US-gal]
Corresponds to the factory setting for the low flow cut off 132
Note!
The switch-off point is specified as a positive hysteresis from the switch-on point
with 50%.
Q
2
b
a
2
H
1
c
t
A0001245
Q
t
H
a
b
c
1
2
EPD
Flow [volume/time]
Time
Hysteresis
SWITCH-ON POINT LOW FLOW CUT OFF = 200 dm3/h
Low flow cut off switch-off point = 50%
Low flow cut off active
Low flow cut off is switched on at 200 dm3/h
Low flow cut off is switched off at 300 dm3/h
Activating empty pipe detection (EPD).

Options:
OFF
ON (empty pipe detection)
Factory setting:
OFF
Note!
The ON option is not available unless the sensor is fitted with an EPD electrode.
The default setting for the EPD function when the device is delivered is OFF. The
function must be activated as required.
When delivered, the measuring device is calibrated with water (500 S/cm).
If the fluid differs from this conductivity, empty-pipe and full-pipe adjustment
has to be performed on site.
To activate the function (ON option), valid adjustment coefficients have to be
available.
The following error messages are displayed if the empty-pipe and full-pipe
adjustment is incorrect:
ADJUSTMENT FULL = EMPTY: the adjustment values for empty pipe and full
pipe are identical.
ADJUSTMENT NOT OK: adjustment is not possible as the fluid conductivity
values are outside the permitted range.
In cases of this nature you must repeat empty-pipe or full-pipe adjustment.
122
Endress+Hauser
Promag 10
Appendix
Functional description PROCESS PARAMETER

EPD-MODE
(continued)
Notes on empty pipe detection (EPD)

Flow cannot be measured correctly unless the measuring tube is completely full.
This status can be monitored at all times by means of the EPD.
An empty or partially filled pipe is a process error. A default factory setting
defines that a notice message is issued and that this process error does not have
any effect on the outputs.
The EPD process error can be output via the configurable status output.
Response to partially filled pipe
If the EPD is switched on and responds to a partially filled or empty pipe, the notice
message "EMPTY PIPE" appears on the display and zero flow is indicated.
If the pipe is partially empty and the EPD is not switched on, the response can vary
in identically configured systems:
Flow reading fluctuates
Zero flow
Excessively high flow values
EPD ADJUSTMENT
Use this function to activate adjustment for an empty or full measuring tube.
Options:
OFF
EPD EMPTY PIPE ADJ.
EPD FULL PIPE ADJUST
Factory setting:
OFF
Note!
An exact description of the procedure for an EPD empty-pipe/full-pipe adjustment
is provided on 68.
Endress+Hauser
123
Appendix
Promag 10
11.10 Group SYSTEM PARAMETER

Functional description SYSTEM PARAMETER
INSTALLATION
DIRECTION SENSOR
Use this function to reverse the sign of the flow quantity, if necessary.
Options:
FORWARDS (flow as indicated by the arrow)
BACKWARDS (flow opposite to direction indicated by the arrow)
Factory setting:
FORWARDS
Note!
Ascertain the actual direction of fluid flow with reference to the direction indicated
by the arrow on the sensor (nameplate).
MEASURING MODE
Use this function to select the measuring mode for all outputs and for the internal
totalizer.
Options:
STANDARD
SYMMETRY
Factory setting:
STANDARD
The responses of the individual outputs and the internal totalizer in each of the
measuring modes are described in detail on the following pages:
Current output
STANDARD
Only the flow components for the selected flow direction are output, (positive or
negative full scale value n = flow direction). Flow components in the opposite
direction are not taken into account (suppression).
Example for current output:
I [mA]
20
4
0
Q
A0001248
SYMMETRY
The output signals of the current output are independent of the direction of flow
(absolute amount of the measured variable). The "VALUE20mA" o (e.g. backflow)
corresponds to the mirrored VALUE20mA n (e.g. flow). Positive and negative flow
components are taken into account.
Example for current output:
mA
20
4
0
Q
A0001249
Note!
The direction of flow can be output via the configurable status output.
124
Endress+Hauser
Promag 10
Appendix

MEASURING MODE
(Contd)
Pulse output
STANDARD
Only flow components of the positive flow direction are output.
Components in the opposite direction are not taken into account.
SYMMETRY
The absolute value of the positive and negative flow components is taken into
account.
Status output
Note!
The information is only applicable if LIMIT VALUE was selected in the function
ASSIGN STATUS OUTPUT.
STANDARD
The status output signal switches at the defined switch points.
SYMMETRY
The status output signal switches at the defined switch points, irrespective of the
sign. In other words, if you define a switch point with a positive sign, the status
output signal switches as soon as the value is reached in the negative direction
(negative sign), (see illustration).
Example for the SYMMETRY measuring mode:
Switch-on point: Q = 4
Switch-off point: Q = 10
m = Status output switched on (conductive)
n = Status output switched off (nonconductive)
Q
10
4
0
-4
- 10
A0001247
Totalizer
STANDARD
Only positive flow components are output.
Negative components are not taken into account.
SYMMETRY
The positive and negative flow components are balanced.
In other words, net flow in the flow direction is registered.
POSITIVE ZERO
RETURN
Use this function to interrupt evaluation of measured variables.

This is necessary when a piping system is being cleaned, for example.
This setting acts on all function and outputs of the measuring device.
Options:
OFF
ON Signal output is set to the "ZERO FLOW" value.
Factory setting:
OFF
Endress+Hauser
125
Appendix
Promag 10

SYSTEM DAMPING
Use this function to set the filter depth of the digital filter.
This reduces the sensitivity of the measuring signal to interference peaks (e.g. high
solids content, gas bubbles in the fluid, etc.).
The system reaction time increases with the filter setting.
User input:
0 to 4
Factory setting:
3
Note!
The system damping acts on all functions and outputs of the measuring device.
The higher the value set, the stronger the damping (higher response time).
126
Endress+Hauser
Promag 10
Appendix
11.11 Group SENSOR DATA

All sensor data (calibration factors, zero point and nominal diameter etc.) are set at the
factory.
"
Caution!
Under normal circumstances you should not change the following parameter settings,
because changes affect numerous functions of the entire measuring facility in general and
the accuracy of the measuring system in particular. Therefore, the functions described below
are provided with an additional prompt (with the code 10) once you enter your private code.
Functional description SENSOR DATA
CALIBRATION DATE
Use this function to view the current calibration date and time for the sensor.
User input:
Calibration date and time.
Factory setting:
Calibration date and time of the current calibration.
Note!
The calibration date and time format is defined in the FORMAT DATE/TIME
function, 110
Selectable formats:
DD.MM.YY 24H
MM/DD/YY 12H A/P
DD.MM.YY 12H A/P
MM/DD/YY 24H
K-FACTOR
Use this function to display the current calibration factor (positive and negative
flow direction) for the sensor. The calibration factor is determined and set at the
factory.
User input:
5-digit fixed-point number: 0.5000 to 2.0000
Factory setting:
Depends on nominal diameter and calibration
Note!
This value is also provided on the sensor nameplate.
ZERO POINT
This function shows the current zero-point correction value for the sensor.
Zero-point correction is determined and set at the factory.
User input:
Max. 4-digit number: -1000 to +1000
Factory setting:
Depends on nominal diameter and calibration
Note!
NOMINAL DIAMETER
This function shows the nominal diameter for the sensor. The nominal diameter
depends on the size of the sensor and is set at the factory.
Options:
2 to 2000 mm
1/12 to 78"
Factory setting:
Depends on the size of the sensor
Note!
Endress+Hauser
127
Appendix
Promag 10
Functional description SENSOR DATA

MEASURING PERIOD
Use this function to set the time for a full measuring period. The duration of the
measuring period is calculated from the rise time of the magnetic field, the brief
recovery time, the (automatically tracked) integration time and the empty pipe
detection time.
User input:
10 to 1000 ms
Factory setting:
Depends on nominal diameter
EPD ELECTRODE
Indicates whether the sensor is equipped with an EPD electrode.

Display:
YES
NO
Factory setting:
YES Electrode fitted as standard
128
Endress+Hauser
Promag 10
Appendix
11.12 Group SUPERVISION

Functional description SUPERVISION
FAILSAFE MODE
The dictates of safety render it advisable to ensure that the device signal processing
assumes a predefined state in the event of a fault. The setting you select here is
valid for:
Current output
Pulse output
Totalizer
Note!
This has no effect on the display.
Options:
MINIMUM VALUE
MAXIMUM VALUE
ACTUAL VALUE
Factory setting:
MINIMUM VALUE
The response of the individual outputs and the totalizer is listed below.
Current output:
MINIMUM VALUE
The current output adopts the value of the lower signal on alarm level (as defined
in the CURRENT RANGE function 114).
MAXIMUM VALUE
The current output is set to the upper value of the signal on alarm level. (The values
in question can be found in the CURRENT RANGE function on 114).
ACTUAL VALUE
Measured value output is based on the current flow measurement. The
fault is ignored.
Pulse output:
MINIMUM or MAXIMUM VALUE
Output is zero pulse
ACTUAL VALUE
Measured value output is based on the current flow measurement (fault is ignored).
Totalizer:
MINIMUM or MAXIMUM VALUE
The totalizer is paused until the fault is rectified.
ACTUAL VALUE
The totalizer continues to count on the basis of the current flow value. The fault is
ignored.
Endress+Hauser
129
Appendix
Promag 10
Functional description SUPERVISION

ALARM DELAY
Use this function to define a time span in which the criteria for an error have to be
satisfied without interruption before an error or notice message is generated.
Depending on the setting and the type of error, this suppression acts on:
Display
Current output
Pulse/status output
User input:
0 to 100 s (in increments of one second)
Factory setting:
0s
"
Caution!
If this function is activated error and notice messages are delayed by the time
corresponding to the setting before being forwarded to the higher-order controller
(process controller, etc.).
It is therefore imperative to check in advance in order to make sure whether a delay
of this nature could affect the safety requirements of the process.
If error and notice messages cannot be suppressed, a value of 0 seconds must be
entered here.
SYSTEM RESET
Use this function to perform a reset of the measuring system.

Options:
NO
RESTART SYSTEM
(Restart without disconnecting main power)
RESET DELIVERY
(Restart without disconnecting main power, the saved settings of the delivery status
(factory settings) are applied).
Factory setting:
NO
SELF CHECKING
Use this function to switch on and off the self-checking function of the electrode
amplifier.
When the function is switched on, the electrode signal circuit is checked against a
reference voltage at 60-second intervals. If there is an impermissible deviation from
the value, system error message #101 is output and displayed on the local display.
Options:
ON
OFF
Factory setting:
OFF
130
Endress+Hauser
Promag 10
Appendix
11.13 Group SIMULATION SYSTEM

Functional description SIMULATION SYSTEM
SIMULATION
FAILSAFE MODE
Use this function to set all outputs and the totalizer to their defined failsafe modes,
in order to check whether they respond correctly.
During this time, the words "SIMULATION FAILSAFE MODE" appear on the display.
Options:
ON
OFF
Factory setting:
OFF
SIMULATION
MEASURAND
Use this function to set all outputs and the totalizer to their defined flow-response
modes, in order to check whether they respond correctly.
During this time, the words "SIMULATION MEASURAND" appear on the display.
Options:
OFF
VOLUME FLOW
Factory setting:
OFF
Note!
The measuring device cannot be used for measuring while this simulation is in
progress.
The setting is not saved if the power supply fails.
VALUE SIMULATION
MEASURAND
Note!
This function is not available unless the SIMULATION MEASURAND function is
active (= VOLUME FLOW).
In this function, a freely selectable value (e.g. 12 m3/s) is specified.
This value is used to test downstream devices and the flowmeter itself.
User input:
5-digit floating-point number [unit], with sign
Factory setting:
0 [unit]
"
Caution!
The setting is not saved if the power supply fails.
Note!
11.14 Group SENSOR VERSION

Functional description SENSOR VERSION
SERIAL NUMBER
Use this function to view the serial number of the sensor.
SENSOR TYPE
Use this function to view the sensor type.
11.15 Group AMPLIFIER VERSION

Functional description AMPLIFIER VERSION
SOFTWARE REVISION
NUMBER
Endress+Hauser
Use this function to view the software revision number of the electronics board.
131
Appendix
Promag 10
11.16 Factory settings

11.16.1 SI units (not for USA and Canada)
Low flow cut off, full scale value, pulse value, totalizer
Nominal diameter
132
Low flow cut off
Full scale value

current output
Pulse value
(approx. v = 0.04 m/s)
(approx. 2 pulses/s
at v = 2.5 m/s)
Totalizer
[mm]
[inch]
1/12"
0.01
dm/min
0.5
dm/min
0.005
dm
dm
1/8"
0.05
dm/min
dm/min
0.025
dm
dm
3/8"
0.1
dm/min
dm/min
0.10
dm
dm
15
"
0.5
dm/min
25
dm/min
0.20
dm
dm
25
1"
dm/min
75
dm/min
0.50
dm
dm
32
1 "
dm/min
125
dm/min
1.00
dm
dm
40
1 "
dm/min
200
dm/min
1.50
dm
dm
50
2"
dm/min
300
dm/min
2.50
dm
dm
65
2 "
dm/min
500
dm/min
5.00
dm
dm
80
3"
12
dm/min
750
dm/min
5.00
dm
dm
100
4"
20
dm/min
1200
dm/min
10.00
dm
dm
125
5"
30
dm/min
1850
dm/min
15.00
dm
dm
150
6"
2.5
m/h
150
m/h
0.025
200
8"
5.0
m/h
300
m/h
0.05
250
10"
7.5
m/h
500
m/h
0.05
300
12"
10
m/h
750
m/h
0.10
350
14"
15
m/h
1000
m/h
0.10
375
15"
20
m3/h
1200
m3/h
0.15
m3
m3
400
16"
20
m/h
1200
m/h
0.15
450
18"
25
m/h
1500
m/h
0.25
500
20"
30
m/h
2000
m/h
0.25
600
24"
40
m/h
2500
m/h
0.30
700
28"
50
m/h
3500
m/h
0.50
30"
60
m/h
4000
m/h
0.50
800
32"
75
m/h
4500
m/h
0.75
900
36"
100
m/h
6000
m/h
0.75
1000
40"
125
m/h
7000
m/h
1.00
42"
125
m/h
8000
m/h
1.00
1200
48"
150
m/h
10000
m/h
1.50
54"
200
m/h
13000
m/h
1.50
1400
225
m/h
14000
m/h
2.00
60"
250
m/h
16000
m/h
2.00
1600
300
m/h
18000
m/h
2.50
66"
325
m/h
20500
m/h
2.50
1800
72"
350
m/h
23000
m/h
3.00
78"
450
m/h
28500
m/h
3.50
2000
450
m/h
28500
m/h
3.50
Endress+Hauser
Promag 10
Appendix
Language
Endress+Hauser
Country
Language
Austria
Deutsch
Belgium
English
Denmark
English
England
English
Finland
English
France
Francais
Germany
Deutsch
Holland
English
Hong Kong
English
International Instruments
English
Italy
Italiano
Japan
English
Malaysia
English
Norway
English
Singapore
English
South Africa
English
Spain
Espanol
Sweden
English
Switzerland
Deutsch
Thailand
English
133
Appendix
Promag 10
11.16.2 US units (only for USA and Canada)

Low flow cut off, full scale value, pulse value, totalizer
Nominal diameter
[inch]
[mm]
Low flow cut off
Full scale value

current output
Pulse value
(approx. 2 pulses/s
at v = 2.5 m/s)
Totalizer
1/12"
0.002
gal/min
0.1
gal/min
0.001
gal
gal
1/8"
0.008
gal/min
0.5
gal/min
0.005
gal
gal
3/8"
0.025
gal/min
gal/min
0.02
gal
gal
"
15
0.10
gal/min
gal/min
0.05
gal
gal
1"
25
0.25
gal/min
18
gal/min
0.20
gal
gal
1 "
32
0.50
gal/min
30
gal/min
0.20
gal
gal
1 "
40
0.75
gal/min
50
gal/min
0.50
gal
gal
2"
50
1.25
gal/min
75
gal/min
0.50
gal
gal
2 "
65
2.0
gal/min
130
gal/min
gal
gal
3"
80
2.5
gal/min
200
gal/min
gal
gal
4"
100
4.0
gal/min
300
gal/min
gal
gal
5"
125
7.0
gal/min
450
gal/min
gal
gal
6"
150
12
gal/min
600
gal/min
gal
gal
8"
200
15
gal/min
1200
gal/min
10
gal
gal
10"
250
30
gal/min
1500
gal/min
15
gal
gal
12"
300
45
gal/min
2400
gal/min
25
gal
gal
14"
350
60
gal/min
3600
gal/min
30
gal
gal
15"
375
60
gal/min
4800
gal/min
50
gal
gal
16"
400
60
gal/min
4800
gal/min
50
gal
gal
18"
450
90
gal/min
6000
gal/min
50
gal
gal
20"
500
120
gal/min
7500
gal/min
75
gal
gal
24"
600
180
gal/min
10500
gal/min
100
gal
gal
28"
700
210
gal/min
13500
gal/min
125
gal
gal
30"
270
gal/min
16500
gal/min
150
gal
gal
32"
800
300
gal/min
19500
gal/min
200
gal
gal
36"
900
360
gal/min
24000
gal/min
225
gal
gal
40"
1000
480
gal/min
30000
gal/min
250
gal
gal
42"
600
gal/min
33000
gal/min
250
gal
gal
48"
1200
600
gal/min
42000
gal/min
400
gal
gal
54"
1.3
Mgal/d
75
Mgal/d
0.0005
Mgal
Mgal
1400
1.3
Mgal/d
85
Mgal/d
0.0005
Mgal
Mgal
60"
1.3
Mgal/d
95
Mgal/d
0.0005
Mgal
Mgal
1600
1.7
Mgal/d
110
Mgal/d
0.0008
Mgal
Mgal
66"
2.2
Mgal/d
120
Mgal/d
0.0008
Mgal
Mgal
72"
1800
2.6
Mgal/d
140
Mgal/d
0.0008
Mgal
Mgal
78"
3.0
Mgal/d
175
Mgal/d
0.001
Mgal
Mgal
2000
3.0
Mgal/d
175
Mgal/d
0.001
Mgal
Mgal
Language
134
Country
Language
USA
English
Canada
English
Endress+Hauser
Promag 10
Index
A
ACCESS CODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
ALARM DELAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Ambient temperature range . . . . . . . . . . . . . . . . . . . . . . 86
Applicator (selection and configuration software) . . . . 72
Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 105
ASSIGN STATUS OUTPUT . . . . . . . . . . . . . . . . . . . . . . . 117
Brief commissioning guide . . . . . . . . . . . . . . . . . . . . . . . . 66

BUS ADDRESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Cable entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Cable specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
CALIBRATION DATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Calibration factor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
CE mark. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
CE mark (Declaration of Conformity) . . . . . . . . . . . . . . . . . 8
Centering sleeve
Promag D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Certificates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 105
CIP cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Cleaning (exterior cleaning). . . . . . . . . . . . . . . . . . . . . . . 69
Code entry (function matrix) . . . . . . . . . . . . . . . . . . . . . . 57
Commissioning
Brief operating instructions . . . . . . . . . . . . . . . . . . . . 66
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
With a new electronics board. . . . . . . . . . . . . . . . . . . 67
Commissioning setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Conductivity of fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Connecting cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Connection
HART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Remote version. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Terminal assignment. . . . . . . . . . . . . . . . . . . . . . . . . . 49
Transmitter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
CONTRAST LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
C-tick mark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
CURRENT RANGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Declaration of Conformity (CE mark) . . . . . . . . . . . . . . . . . 8

DEFINE PRIVATE CODE . . . . . . . . . . . . . . . . . . . . . . . . . 111
Degree of protection . . . . . . . . . . . . . . . . . . . . . . . . . . 53, 86
Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Device description files . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
DEVICE ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Device variable via HART protocol. . . . . . . . . . . . . . . . . . 60
Display
Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55, 105
Turning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Endress+Hauser
Drinking water approval. . . . . . . . . . . . . . . . . . . . . . . . . 106
Electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Electrodes
EPD electrode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
EMC (electromagnetic compatibility) . . . . . . . . . . . . 47, 87
Empty-pipe/full-pipe adjustment . . . . . . . . . . . . . . . . . . . 68
Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
EPD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
EPD ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
EPD ELECTRODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Error message types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Ex approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Exterior cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Factory setting
SI units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
US units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
FAILSAFE MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Field Xpert SFX100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
FieldCare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59, 72
Fieldcheck (tester and simulator) . . . . . . . . . . . . . . . . . . . 72
Fitted electrodes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Flow rate/limits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
FORMAT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
FORMAT DATE/TIME . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Function matrix
Brief operating instructions . . . . . . . . . . . . . . . . . . . . . 56
Illustration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
FXA 193 service interface . . . . . . . . . . . . . . . . . . . . . . . . . 72
FXA193 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Galvanic isolation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Ground cable
Promag E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Promag L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Promag P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Promag W . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Group
AMPLIFIER VERSION . . . . . . . . . . . . . . . . . . . . . . . . 131
COMMUNICATION . . . . . . . . . . . . . . . . . . . . . . . . . . 121
CURRENT OUTPUT . . . . . . . . . . . . . . . . . . . . . . . . . . 114
DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
PROCESS PARAMETER . . . . . . . . . . . . . . . . . . . . . . 122
PULSE/STATUS OUTPUT . . . . . . . . . . . . . . . . . . . . . 116
SENSOR DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
SENSOR VERSION . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
SIMULATION SYSTEM . . . . . . . . . . . . . . . . . . . . . . . 131
SUPERVISION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
SYSTEM PARAMETER . . . . . . . . . . . . . . . . . . . . . . . 124
SYSTEM UNITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
TOTALIZER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
135
Promag 10
HART
Command classes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Communicator DXR 375 . . . . . . . . . . . . . . . . . . . . . . . 59
Device description files. . . . . . . . . . . . . . . . . . . . . . . . . 60
Device status / Error messages . . . . . . . . . . . . . . . . . . 65
Write protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
HART WRITE PROTECTION . . . . . . . . . . . . . . . . . . . . . . 121
Hazardous substances . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
HOME position (operating mode) . . . . . . . . . . . . . . . . . . 55
Incoming acceptance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Inlet/outlet run . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Installation
Promag D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Promag E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Promag H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Promag L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Promag P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Promag W . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Remote version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
See Installation instructions
Installation conditions
Adapters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Down pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
EPD electrode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Foundations, supports . . . . . . . . . . . . . . . . . . . . . . . . . 15
Inlet/outlet run . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Installation of pumps . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Mounting location . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Orientation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Partially filled pipes . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Vibrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
INSTALLATION DIRECTION SENSOR. . . . . . . . . . . . . . . 124
K-FACTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Local display
See Display
Low flow cut off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
MANUFACTURER ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Material load diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Maximum measured error. . . . . . . . . . . . . . . . . . . . . . . . . 85
Measured variable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
MEASURING MODE . . . . . . . . . . . . . . . . . . . . . . . . 124125
MEASURING PERIOD . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Measuring principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Measuring range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Measuring system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
136
Mechanical construction . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Medium pressure range . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Medium temperature range. . . . . . . . . . . . . . . . . . . . . . . . 87
Mounting bolts
Promag D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Nameplate specifications
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
NOMINAL DIAMETER . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Nominal diameter and flow rate
Promag W . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Operable flow range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Operating elements. . . . . . . . . . . . . . . . . . . . . . . . . . 55, 105
OPERATING MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Device description files . . . . . . . . . . . . . . . . . . . . . . . . . 60
FieldCare. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Operating programs . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Operational safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Order code
Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Output. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
OUTPUT SIGNAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Output signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
OVERFLOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Performance characteristics. . . . . . . . . . . . . . . . . . . . . . . . 85
Pig (cleaning). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
POSITIVE ZERO RETURN . . . . . . . . . . . . . . . . . . . . . . . . 125
Post-connection
Check. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Post-installation
Check. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Potential equalization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Power supply failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Pressure Equipment Directive . . . . . . . . . . . . . . . . . . . . 106
Pressure loss
Adapters (reducers, expanders) . . . . . . . . . . . . . . . . . 15
Pressure tightness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Process connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Process error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Process errors (definition) . . . . . . . . . . . . . . . . . . . . . . . . . 58
Programming mode
Disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Promag D
Centering sleeve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Endress+Hauser
Promag 10
Mounting bolts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Tightening torques . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Promag D mounting kit. . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Promag E
Ground cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Promag H
Cleaning with pigs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Weld nipple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Promag H cleaning with pigs . . . . . . . . . . . . . . . . . . . . . . 26
Promag H with weld nipples . . . . . . . . . . . . . . . . . . . . . . 26
Promag L
Ground cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Promag P
Ground cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Promag W
Ground cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
PULSE VALUE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
PULSE WIDTH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Reference operating conditions . . . . . . . . . . . . . . . . . . . . 85

Registered trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Remote operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Remote version
Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Repeatability. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
RESET TOTALIZER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Response of the status output . . . . . . . . . . . . . . . . . . . . 119
Response to errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Returning devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Safety icons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Sanitary compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Promag D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Promag E. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Promag H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Promag L. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Promag P. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Promag W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Endress+Hauser
SELF CHECKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130

SENSOR TYPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
SERIAL NUMBER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Serial number
Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Shock resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Signal on alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
SIMULATION FAILSAFE MODE . . . . . . . . . . . . . . . . . . 131
SIMULATION MEASURAND . . . . . . . . . . . . . . . . . . . . . 131
SIP cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Standards, guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
SUM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Surface roughness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
SW REV. NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Switching behavior of the status output. . . . . . . . . . . . 120
Switching on (measuring device) . . . . . . . . . . . . . . . . . . . 66
SWITCH-OFF POINT . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
SWITCH-ON POINT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
SWITCH-ON POINT LOW FLOW CUT OFF . . . . . . . . . 122
SYSTEM DAMPING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
System error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
System errors (definition) . . . . . . . . . . . . . . . . . . . . . . . . . 58
SYSTEM RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
TAG DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

TAG NAME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Temperature
Ambient . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Medium . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
TEST DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Tightening torques
Promag D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Promag E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Promag L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Promag P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Promag W . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
TIME CONSTANT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Types of error (system and process errors) . . . . . . . . . . . 58
UNIT VOLUME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

UNIT VOLUME FLOW . . . . . . . . . . . . . . . . . . . . . . . . . . 109
VALUE 20 mA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
VALUE SIMULATION MEASURAND . . . . . . . . . . . . . . 131
Vibration resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Vibrations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93, 99
Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
137
Promag 10
ZERO POINT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
138
Endress+Hauser
Promag 10
Endress+Hauser
139
www.addresses.endress.com

Promag10 BA00082DEN 1615

Uploaded by

Copyright:

Available Formats

Promag10 BA00082DEN 1615

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Promag10 BA00082DEN 1615

Uploaded by

Copyright:

Available Formats

BA00082D/06/EN/16.

Valid as of software version

10.1 Technical data at a glance . . . . . . . . . . . . . . . . . . . 83

Incoming acceptance, transport and storage . . . . . 9

Connecting the remote version . . . . . . . . . . . . . .

Display and operating elements . . . . . . . . . . . . .

11.1 Illustration of the function matrix . . . . . . . . . .

Installation, commissioning and operation

Please note the following:

Please note the following:

Notes on safety conventions and icons

The flow measuring system consists of the following components:

Nameplate of the transmitter

-20C (-4F) <Tamb<+60C (+140F)

Nameplate specifications for the "Promag 10" transmitter (example)

Nameplate of the sensor

-20C (-4F)<Tamb<+60C (+140F)

See operating manual

Nameplate specifications for the "Promag" sensor (example)

Nameplate specifications for transmitter (example)

Certificates and approvals

KALREZ and VITON

Incoming acceptance, transport and storage

On receipt of the goods, check the following:

Transporting sensors with DN 300 (12")

Transporting flanged devices DN 350 (14")

Transporting sensors with DN 350 (14")

Please note the following:

Partially filled pipes

Installation in a partially filled pipe

Measures for installation in a down pipe

Inlet and outlet run

Inlet and outlet runs

Secure the piping and the sensor if vibration is severe.

Measures to prevent vibration of the device (L > 10 m (32.8 ft))

Correct support for large nominal diameters (DN 350 / 14")

Calculate the ratio of the diameters d/D.

Pressure loss due to adapters

Nominal diameter and flow rate

Min./max. full scale value (v 0.3 or 10 m/s) in [m/h]

Min./max. full scale value (v 0.3 or 10 m/s) in [dm/min]

Recommended flow (US units)

Min./max. full scale value (v 0.3 or 10 m/s) in [gal/min]

Min./max. full scale value (v 0.3 or 10 m/s) in [Mgal/d]

Length of connecting cable

Permissible cable length for the remote version

Area shaded gray = permitted range

Installing the Promag D sensor

Mounting the sensor

Arrangement of the mounting bolts and centering sleeves

1 = Mounting bolts with centering sleeves

Screw tightening torques (Promag D)

Tightening torque [Nm]

smooth seal face

EN (DIN) flanges: 4-hole with centering sleeves

EN (DIN) flanges: 8-hole without centering sleeves

Tightening torques, mounting bolts and centering sleeves for JIS 10 K

Tightening torque [Nm]

smooth seal face