VT-CC1101-433M Wireless Module

User Guide

V-CHIP MICROSYSTEMS Co. Ltd

Address: Room 612-613, Science and Technology Service Center Building,
NO.1, Qilin Road, Nanshan District, Shenzhen, Guangdong
TEL0755-88844812
FAX0755-22643680
[email protected]
Post Code518052
Web Sitewww.digiRF.com

VT-CC1101-433M

General Description
VT-CC1101-433M is based on RF Transceiver CC1101 of TI Chipconits a small size and ultra low power UHF
wireless module. CC1101 is a low cost true single chip UHF transmitter designed for very low power wireless
applications. The circuit is mainly intended for the ISM (Industrial, Scientific and Medical) and SRD (Short
Range Device) frequency bands at 315, 433, 868 and 915 MHz, The MAX RF output power can be set as high as
+10dBm, with data rate as high as 500Kbps. The module integrated many RF functions thus you can use it
conveniently and reducing your development time.

Features

Central frequency is 433MHz, Frequency bands :387~464MHz

Programmable output power up to +10dBm for all supported

frequenciesthe communication distance is above 200m in sight .

High receiver sensitivity down to -110dBm(at 2.4Kbps data rate)

Programmable baseband modulator with

GFSK/2-FSK/ASK/OOK/MSK

Programmable data rate 1.2500Kbps

64-byte TX data FIFO

Optional Forward Error Correction with Interleaving

Support carrier sense and digital RSSI output.

Low current consumption with receive mode <20mA, transmit mode at +10dBm output power <30mA

Low current consumption at power down state <2uA

Wake-on-radio functionality for automatic low-power RX polling

Integrated analog temperature sensor

Efficient SPI interface, All registers can be programmed with one burst transfer

Small dimension17.0mm19.0mm2.4 mm

Operating supply voltage1.83.6V DC

Applications

Logistics Tracking System, Warehouse patrol, Electronic label.

Replace RS232 and RS485 in data transmission

Industrial monitoring and control in data acquisition

AMR Automatic Meter Reading

Home and building automation

Consumer Electronics products of wireless control

Wireless alarm and security systems

Wireless sensor networks

COPYRIGHT @ 2012 Shenzhen V-CHIP MICROSYSTEMS Co. Ltd

VT-CC1101-APR-2012

VERSION:

VT-CC1101-433M

COPYRIGHT @ 2012 Shenzhen V-CHIP MICROSYSTEMS Co. Ltd

VT-CC1101-APR-2012

VERSION:

VT-CC1101-433M

General Characteristics
Test operating conditionsTa=25CVCC=3.3V if nothing else stated.
Parameter

Type

Condition/Note

Operating supply voltage

DC 1.83.6V

Central frequency

433MHz

Frequency accuracy

10KHz

Modulation format

GFSK/2-FSK/ASK/OOK/M
SK

Programmable

Transmit power

-30+10dBm

Programmable

TX current consumption

<30mA

Po=10dBm

Receiver sensitivity

-110dBm

2.4Kbps

RX current consumption

<30mA

2.4Kbps

Sleep State current consumption

<2uA

Refer to IC operation states

Data rate

1.2500Kbps

Programmable

Spurious emissions and harmonics

< -30dBm

TX power +10dBm.

Communication distance

>200m

Use VT-CC1101-433M as a receiver, 2-FSK

modulation, 1.2kBaud data rata, +10dBm output
power.

Antenna impedance

50ohm

Operating temperature

-20+75 C

Storage temperature range

-50+125C

Dimension

17.0 mm19.0 mm2.4mm

Can be programmable to other frequency in bands

387~464MHz

See more in PCB description

Note
Note
1 The module transmission data rate will affect Transmission distance ,the higher the data rate , the closer the
distance, and the lower the receiving sensitivity.
2 The supply voltage to the module will affect TX power, in the operating supply voltage range, the lower the
voltage, the lower the TX power.
3 The module central frequency will change as the operating temperature change, use it under suggest temperature,
the module can work well.
4 The antenna will strongly affect the communication distance, please select matched antenna and connect it
correctly.
5 The module mount will affect the communication distance.

COPYRIGHT @ 2012 Shenzhen V-CHIP MICROSYSTEMS Co. Ltd

VT-CC1101-APR-2012

VERSION:

VT-CC1101-433M

PCB Description

Pin Configuration
Pin name

Pin type

Description

VCC

Power(Analog)

1.8 V - 3.6 V analog power supply connection.

GND

Ground

Connect to the system ground.

SI

Digital Input

Serial configuration interface, data input.

SCLK

Digital Input

Serial configuration interface, clock input.

SO

Digital Output

Serial configuration interface, data output.

Optional general output pin when CSN is high.

GDO2

Digital I/O

Programmable Clock output, down-divided from XOSC

GDO0

Digital I/O

Programmable Clock output, down-divided from XOSC.

CSN

Digital Input

Serial configuration interface, chip select, active low.

ANT

RF I/O

RF output signal from PA, connect to the Antenna.

COPYRIGHT @ 2012 Shenzhen V-CHIP MICROSYSTEMS Co. Ltd

VT-CC1101-APR-2012

VERSION:

VT-CC1101-433M

Circuit Interface

Note
Note
1 The module power supply voltage range is DC 1.8 3.6V, above DC 3.6V, the module will damage. It is
recommended work at DC 3.3 V.
2 The module interface use half circle pad to soldering on the system PCB board, the GND must soldering to
the system digital GND reliably.
3 The antenna must the get to the modules ANT pin as close as possible.
4 The MCU which dont have integrated SPI interface can also control the module, use the normal I/O port to
work like SPI timing to read and write. The SPI data rate is below 10MHz.
5 The interface can connect directly to the MCU which use 3.3V power supply, there is no need serial resistor.
If the I/O is open-drain, the pull-up resistor will be added. When connect to the MCU which use 5V power
supply, the MCUs I/O output current beyond 10 mA, a 2~5k ohm resistor will be series to divide the voltage,
or it will damage the module.
6 The modules pin GDO0 is a general digital I/O port, it can be programmable to produce trigger signal or
clock output.
7 In the multiple channel application, the channel spacing is recommended to set as 1MHz, or there will be a
same frequency interference.

COPYRIGHT @ 2012 Shenzhen V-CHIP MICROSYSTEMS Co. Ltd

VT-CC1101-APR-2012

VERSION:

VT-CC1101-433M

Operation States
CC1101s operation states contain: Sleep State, Idle State, Active StateSleep State is the lowest power mode.
After wake up from Sleep State, the module get into Idle State. Except the Sleep State, each state can be switch by
SPI interface, also programmed to auto-switch. CC1101s radio control state diagram is shown as below, for detail
information in the CC1101 datasheet.

COPYRIGHT @ 2012 Shenzhen V-CHIP MICROSYSTEMS Co. Ltd

VT-CC1101-APR-2012

VERSION:

VT-CC1101-433M

Data Transmission
The CC1101 contains a 64 byte FIFO for data to be transmitted, built-in hardware support for packet oriented
radio protocols, e.g. Preamble bytes, Synchronization Word, Whitening the data, CRC checksum, Interleave and
Forward Error Code, Address checksum. The SPI interface is used for sending commend control and writing to
the TX FIFO.
The format of the data packet can be configured and consists of the following figure

In addition, CC1101 supports fixed packet length protocols, variable packet length protocols and infinite packet
length. Details refer to the CC1101 datasheet.

Configuration Registers
The configuration of CC1101 can be done with software SmartRF Studio7. Complete descriptions of the registers
are given in the CC1101 datasheet. We can provide evaluation board and demo code to the customer to develop
and evaluate the modules capability.

Dimension

COPYRIGHT @ 2012 Shenzhen V-CHIP MICROSYSTEMS Co. Ltd

VT-CC1101-APR-2012

VERSION:

VT-CC1101-433M

Antenna
We can provide antenna match to the module. And if there is some special requirements to satisfy, we can
coordinate with you to select antenna, match antenna to the module in order to make the product work well.
Some recommend antennas as the table below.

Standard
Spring antenna
antennaStandard
Standard
Characteristic: small size, low cost, embedded
conveniently.

Optional
SMA rubber antenna
antennaOptional
Optional
Characteristic: medium-scale, low cost, high gain

Optional
Magnetic Mount Antenna
AntennaOptional
Optional
Characteristic: high gain, Magnetic Mount
suitable for mount on iron box.

Note: Standard is for free, optional need another payment and the cost refer to the antenna price.

COPYRIGHT @ 2012 Shenzhen V-CHIP MICROSYSTEMS Co. Ltd

VT-CC1101-APR-2012

VERSION:

VT-CC1101-433M

Questions and Answers

Description

Reason and Solution

1 The power supply connect not well, check the module VCC whether it is out of maximum
rating.
2The signal line connect not well, check the module SPI interface.

Cant

3 The settings of the transmitter module and receiver module are not the same. Check these

communication
modules register configuration.
4Signal block. If the transmitter work with a high TX power, and the receiver was put at a short
distance(<0.5m), maybe there is a signal block to make no communication.
1The application environment is too bad or the antenna is shield. Put the antenna to a better place
outside or higher throw a coaxial line , replace it with a higher gain antenna.
Communication

2 The work space contains a same frequency interference source, or a strong magnetic field

distance is too
interference, power source disturbance. Try to change the carrier frequency or get far away from
short
the source of the disturbance.
3The power supply is not strong. Check the voltage and the current whether it is enough.
1The power supply ripple is too big, Change the power supply.
2Check the module register configuration, it is recommended to set as the CC1101-datasheet.
High data error
3There is a carrier frequency interference, change the channel.
4The antenna unmatched to the module RF interface, change another matched antenna.

Development Package:
1.

CC1101 datasheetCC1101.pdf

2.

CC1101 register configuration toolSmartRF Studio 7 v1.4.9.zip

3.

CC1101 demo code (CC1101 Demo Code.rar

4.

Hard ware toolsTI Chipcon Evaluation Board

Note
Note
1 You can get the development package above from the salesman when you order the module.
please refer to our latest development materials.
2 As version update
updateplease

COPYRIGHT @ 2012 Shenzhen V-CHIP MICROSYSTEMS Co. Ltd

VT-CC1101-APR-2012

VERSION:

VT-CC1101-433M

IMPORTANT NOTICE
V-CHIP MICROSYSTEMS Co. Ltd (below called V-CHIP) reserve the right to make corrections,
modifications, enhancements, improvements, and other changes to its products and services at any time and
to discontinue any product or service without notice. Customers should obtain the latest relevant information
before placing orders and should verify that such information is current and complete.
V-CHIP warrants performance of its hardware products to the specifications applicable at the time of sale
in accordance with V-CHIPs standard warranty.
V-CHIP does not warrant or represent that any license, either express or implied, is granted under any
V-CHIP patent right, copyright, mask work right, or other V-CHIP intellectual property right relating to any
combination, machine, or process in which V-CHIP products or services are used. Reproduction of V-CHIP
information in V-CHIP data books or data sheets is permissible only if reproduction is without alteration and
is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this
information with alteration is an unfair and deceptive business practice. V-CHIP is not responsible or liable
for such altered documentation. Information of third parties may be subject to additional restrictions. Resale
of V-CHIP products or services with statements different from or beyond the parameters stated by V-CHIP
for that product or service voids all express and any implied warranties for the associated V-CHIP product or
service and is an unfair and deceptive business practice. V-CHIP is not responsible or liable for any such
statements.

COPYRIGHT @ 2012 Shenzhen V-CHIP MICROSYSTEMS Co. Ltd

VT-CC1101-APR-2012

VERSION: