10Gbps 20km LC BIDI SFP+ Transceiver

10Gbps 20km LC BIDI SFP+ Transceiver
Rev. A1, Apr.21 2015
PTE20-D4I-2733/3327
Features
Up to 10.3125 Gbps data rate
1270nm DFB Tx/1330nm PIN Rx for PTE20-D4I-2733
1330nm DFB Tx/1270nm PIN Rx for PTE20-D4I-3327

Simplex LC receptacle optical interface compliant
Single +3.3V power supply
Hot-pluggable
AC coupling of LVPECL signals

International Class1 laser safety certified
Operating temperature range:
Industry: -40~85
RoHS Compliant
DDMI function available with internally calibrated mode
Application
10GBASE-LR/LW
10G Fiber Channel
Standard
Compliant with MSA SFP+ specification
Compliant with SFF-8472
CPRI Line Rate Option: 9830.4Mbps

Compliant to IEEE 802.3ae
www.mnc-tek.com
Page 1 of 11
Dongguan Mentech Optical & Magnetic Co., Ltd.

Rev. A1, Apr.21 2015
Specification:
Absolute Maximum Ratings
Parameter
Symbol
Min
Max
Unit
Storage temperature
TS
-40
85
Power Supply Voltage
Vcc
-0.5
+4
Relative Humidity
RH
95
Recommended Operating Conditions

Parameter
Operating Case
Temperature(Industry)
Power Supply Voltage
Symbol
Min
Tc
-40
Vcc
3.135
Supply Current
Icc
Typical
3.3
Max
Unit
85
3.465
300
mA
Data Rate
10.3125
Gbps
Fiber Length 9/125m core

SMF
20
km
Electrical Characteristics
Parameter
Transmitter differential input
voltage
Receiver differential output
Voltage
Transmit Fault (TX_Fault)
Loss of Signal (LOS)
TX Disable
Symbol
Min
Typical
Max
Unit
Notes
180
700
mV
300
850
mV
Voh
Vcc
LVTTL
Vol
0.8
LVTTL
Voh
Vcc
LVTTL
Vol
0.8
LVTTL
Voh
Vcc
LVTTL
Vol
0.8
LVTTL
Max
Unit
Notes
0.5
dBm
Optical transmitter Characteristics

Parameter
Symbol
Min
Launched Power (avg.)
Pout
-7.2
Operating Wavelength Range
Spectral Width
www.mnc-tek.com
Typical
1320
1330
1340
1260
1270
1280
1
PTE20-D4I-3327
nm
PTE20-D4I-2733
nm
DFB
Page 2 of 11

Rev. A1, Apr.21 2015
Side Mode Suppression Ratio
SMSR
30
dB
Extinction Ratio
ER
3.5
dB
Relative Intensity Noise
RIN
-128
Return Loss Tolerance
12
Optical Rise/Fall Time
Tris/Tfall
Transmitter and Dispersion

Penalty
Optical Tx Output disable
dB/Hz
dB
3
50
Ps
TDP
3.2
dB
Pdis
-45
dBm
Output Eye Diagram
28
Complies with IEEE802.3ae eye masks when filtered

Optical receiver Characteristics
Parameter
Symbol
Receiver Sensitivity
Wavelength Range
Min
Typical
LOS
Unit
Notes
-14
dBm
1320
1340
1260
1280
Receiver Reflectance
Optical Power Input Overload
Max
-12
Pin-max
Optical Dessert
Pd
Optical Assert
Pa
LOS hysteresis
0.5
-16
-30
0.5
PTE20-D4I-2733
nm
PTE20-D4I-3327
dB
dBm
dBm
dB
Note1. The supply current is SFP+ modules working current.

Note2. For the measurements, the device was driven with 2^31-1 PRBS pattern
Note3. Optical transition time is the time interval required for the rising or falling edge of an optical pulse
to transition between the 20% and 80% amplitudes relative to the logical 1 and 0 levels.
Note4. Measured with a PRBS 2 31-1 test pattern, @10.3125Gbps, ER=4dB, BER<10 -12
Note5. The LOS Hysteresis minimizes chatter on the output line. In principle, Hysteresis alone does not
guarantee chatter-free operation.
Digital Diagnostic Monitoring Information

Parameter
Accuracy
Calibration
Note
Temperature
3C
internal
-40~85
Voltage
3%
internal
Vcc=3.3V5%
Bias Current
10%
internal
Specified by normal value
TX Power
2dB
internal
-8.2~0.5dBm
RX Power
3dB
internal
-16~0.5dBm
www.mnc-tek.com
Page 3 of 11

Rev. A1, Apr.21 2015
Pin definition
The SFP+ modules are hot-pluggable. Hot pluggable refers to plugging in or unplugging a module
while the host board is powered. The SFP+ host connector is a 0.8 mm pitch 20 position right angle
improved connector specified by SFF-8431, or stacked connector with equivalent with equivalent
electrical performance. Host PCB contact assignment is shown in Figure 1 and contact definitions are
given in Table 5. SFP+ module contacts mates with the host in the order of ground, power, followed by
signal as illustrated by Figure 2 and the contact sequence order listed in Table 5.
SFP+ Pad assignment Top View
SFP+ Module Contact Assignment
Pin
Symbol
Name/Description
Power
Seq.
Ref.
VeeT
Transmitter Ground (Common with Receiver Ground)
1st
TX_Fault
Transmitter Fault, Low: normal; High: abnormal
3rd
TX_Disable
3rd
SDA
3rd
Transmitter Disable
www.mnc-tek.com
High: Transmitter off

Low: Transmitter on
2-Wire Serial Interface Data Line
Page 4 of 11

Rev. A1, Apr.21 2015
(Same as MOD-DEF2 in INF-8074i)
5
SCL
2-Wire Serial Interface Data Line

(Same as MOD-DEF2 in INF-8074i)
3rd
Mod_ABS
Module Absent, Connect to VeeT or VeeR in Module
3rd
RS0
Rate Select 0, optionally controls SFP+ module receiver
3rd
3rd
Receiver Loss of Signal indication

8
RX_LOS
High: loss of signal

Low: signal detected
RS1
Rate Select 1, optionally controls SFP+ module

transmitter
3rd
10
VeeR
Receiver Ground
1st
11
VeeR
Receiver Ground
1st
12
RD-
Receiver Inverted DATA out. AC Coupled. CML-O
3rd
13
RD+
Receiver Non-inverted DATA out. AC Coupled. CML-O
3rd
14
VeeR
Receiver Ground
1st
15
VccR
Receiver Power Supply
2nd
10
16
VccT
Transmitter Power Supply
2nd
10
17
VeeT
Transmitter Ground
1st
18
TD+
Transmitter Non-Inverted DATA in. AC Coupled. CML-I
3rd
11
19
TD-
Transmitter Inverted DATA in. AC Coupled. CML-I
3rd
11
20
SDA
Transmitter Ground
1st
SFP+ Module PIN Definition

Power Seq.: Pin engagement sequence during hot plugging.
Notes:
1. The module signal ground contacts.
2. This pin is an open drain/collector and should be pulled up to Vcc-host in the host with a 4.7k~10k
Ohm resistor.
3. This pin should be pulled up to Vcct with a 4.7k~10k Ohm resistor in modules.
4. SDA&SCL (IIC) are needed pull up 4.7k~10k Ohm resistors on host board.
5. Mod_ABS is connected to VeeT or VeeR in the SFP+ module.
6. Rate Select 0,Optionally controls SFP+ module receiver , High: RX input signaling rate 4.25GBd
and Low: RX input signaling rate4.25GBd.
7. Module RX_Los of signal indication need pull up 4.7k~10k Ohm resistor on host board.
8. Rate Select 1,Optionally controls SFP+ module transmitter, High: Tx input signaling rate 4.25GBd
and Low : Tx input signaling rate4.25GBd.
9. RD -/+: These are the differential receiver outputs. They are CML AC-coupled with 100 Ohm
terminal resistor matching internal.
10. VccR and VccT are the receiver and transmitter power supplies.
11. TD-/+: These are the differential transmitter inputs. They are CML AC-coupled with 100 Ohm
terminal resistor matching internal.
www.mnc-tek.com
Page 5 of 11

Rev. A1, Apr.21 2015
Block Diagram
Typical application Circuit

VeeT(1720)
0.1uF
3.3V
1uH
10uF
VccT16
VccR15
0.1uF
1uH
3.3V
4.7k~10Kohm
MAC Rx_LOS
Host board
Ser Data InSer Data In+

SerDes
Ser Data Out+
Ser Data Out-
VeeR(101114)
RX_LOS-(8)
Z=50ohm
RD-(12)
Z=50ohm
RD+(13)
Z=50ohm
TD+(18)
Z=50ohm
TD-(19)
0.1uF
100ohm
Limiting
Amplifier
0.1uF
0.1uF
100ohm
Laser
Driver
0.1uF
3.3V
4.7k~10Kohm
MAC TX_Disable
MAC TX_Fault
SFP+ Module
0.1uF
10uF
3.3V
4.7k~10Kohm
3.3V
4.7k~10Kohm
MAC SDA
MAC SCL
Module Present
www.mnc-tek.com
4.7k~10Kohm
4.7k~10Kohm SDA(4)
SCL(5)
Monotoring
Temperature
Supply Voltage
Bias Current
TX Power
RX Power
EEprom
MOD_ABS(6)
Page 6 of 11

Rev. A1, Apr.21 2015
Digital Diagnostic Memory Map
EEPROM Serial ID Memory Contents

The optical transceiver contains an EEPROM. It provides access to sophisticated identification
information that describes the transceivers capabilities, standard interfaces, manufacturer, and other
information. When the serial protocol is activated, the host generates the serial clock signal (SCL, Mod
Def 1). The positive edge clocks data into those segments of the EEPROM that are not writing protected
within the SFP transceiver. The negative edge clocks data from the SFP transceiver. The serial data
signal (SDA, Mod Def 2) is bi-directional for serial data transfer. The host uses SDA in conjunction with
SCL to mark the start and end of serial protocol activation. The memories are organized as a series of
8-bit data words that can be addressed individually or sequentially.
The Module provides diagnostic information about the present operating conditions. The transceiver
generates this diagnostic data by digitization of internal analog signals. Calibration and alarm/warning
threshold data is written during device manufacture. Received power monitoring, transmitted power
monitoring, bias current monitoring, supply voltage monitoring and te mperature monitoring all are
implemented. The diagnostic data are raw A/D values and must be converted to real world units using
calibration constants stored in EEPROM locations 56 95 at wire serial bus address A2h. The digital
diagnostic memory map specific data fields define as following.
EEPROM Serial ID Memory Contents (2-Wire Address A0h)

Address
Name of field
Hex
Description
BASE ID Fields
00
Identifier
03
SFP transceiver
01
Ext. Identifier
04
Serial ID module supported for SFP
02
Connector
07
LC
03-05
Transceiver Codes
00 00 00
Not defined
06
Transceiver Codes
00
Not defined
www.mnc-tek.com
Page 7 of 11

Rev. A1, Apr.21 2015
07-10
Transceiver Codes
00 00 00
Not defined
11
Encoding
06
Encoding codes
12
BR, Nominal
13
Rate Identifier
67
10.3GHz
14
Length(9um)-km
14
15
Length(9um)-m
C8
16
Length(50um)
17
Length(62.5um)
18
Length(cable)
00
Not support cable
19
Length(OM3)
Not support OM3
20-35
Vendor Name
MENTECHOPTO(ASCII character)
36
Reserved
32
4D 45 4E 54 45 43 48
4F 50 54 4F
00
37-39
Vendor OUI
00 00 00
Not defined
40-55
Vendor P/N
56-59
Vendor P/N Rev.
41 30 20 20
A0(ASCII character)
60-61
Laser Wavelength
04 F6/05 32
1270/1330nm
62
Reserved
00
Not defined
63
CC_BASE
XX
Check sum of bytes 0-62
Transceiver transmit distance
Not defined
Extended ID Fields
64-65
Options
00 1A
66
BRmax
14
67
BRmin
14
68-83
Vendor SN
MA..xx
84-91
Date Code
Data Code
92
Diagnostic Monitoring
Type
68
93
Enhanced options
F0
94
SFF-8472 compliant
05
95
CC-EXT
XX
RX_LOSTX_Fault are
implemented
Upper bit rate margin,20%
Lower bit rate margin,20%
Vendor Serial Number in ASCII
character
Vendor Date Code in ASCII character
Digital Diagnostic monitoring
implemented External calibrated is
implemented, RX measurement type
is Average Power
Optional Alarm/warning flags, soft
Tx_Fault monitoring, soft LOS
monitoring are implemented
SFF-8472 compliant with revision
11.0
Check sum of bytes 64-94
Vendor Specific ID Field

96-127
Vendor Specific
00
Vendor specific EEPROM
128-255
Reserved
00
Reserved for future use
www.mnc-tek.com
Page 8 of 11

Rev. A1, Apr.21 2015
Digital Diagnostic Monitoring InterfaceAlarm and Warning Thresholds

(2-Wire Address A2h)
Address
#Bytes
Name
Real Value
Unit
00-01
Temp High Alarm
100
02-03
Temp Low Alarm
-45
04-05
Temp High Warning
95
06-07
Temp Low Warning
-40
08-09
Voltage High Alarm
3.63
10-11
Voltage Low Alarm
2.97
12-13
Voltage High Warning
3.47
14-15
Voltage Low Warning
3.14
16-17
Bias High Alarm
90
mA
18-19
Bias Low Alarm
mA
20-21
Bias High Warning
4
100
22-23
Bias Low Warning
mA
dBm
mA
24-25
TX Power High Alarm
80
26-27
TX Power Low Alarm
dBm
28-29
TX Power High Warning
0.5
dBm
30-31
TX Power Low Warning
-7
dBm
32-33
RX Power High Alarm
dBm
34-35
RX Power Low Alarm
-16
dBm
36-37
RX Power High Warning
dBm
38-39
RX Power Low Warning
-15
dBm
40-55
16
Reserved
Reserved
www.mnc-tek.com
Hex
Page 9 of 11

Rev. A1, Apr.21 2015
Package Outline
Dimensions are in millimeters. All dimensions are 0.1mm unless otherwise specified. (unit: mm)
Regulatory Compliance
Feature
Test
Method
Electrostatic Discharge
MIL-STD-883E
Class 1(>1000V for SFI
(ESD) to the Electrical Pins
Method 3015.7
Electrostatic Discharge
(ESD) Immunity
IEC61000-4-2
Electromagnetic
CISPR22 ITE Class B

FCC Class B
Interference (EMI)
CENELEC EN55022
VCCI Class 1
Immunity
IEC61000-4-3
FDA 21CFR 1040.10 and
Eye Safety
www.mnc-tek.com
1040.11
EN (IEC) 60825-1,2
pins, >2000V
for other pins.)
Class 2(>4.0kV)
Comply with standard
Comply with standard

Compatible with Class I laser
Product
Page 10 of 11

Rev. A1, Apr.21 2015
Ordering information
Specifications
Part. No
Pack
Rate
(Gbps)
PTE20-D4I-2733
SFP+
10.3125
1270
-7.2~0.5
PIN
-14
PTE20-D4I-3327
SFP+
10.3125
1330
-7.2~0.5
PIN
-14
www.mnc-tek.com
Tx
Po
nm dbm
RX
Sen
Temp
dbm
Reach
KM
DDM
-40~85
20
-40~85
20
Page 11 of 11

10Gbps 20km LC BIDI SFP+ Transceiver

Uploaded by

Copyright:

Available Formats

10Gbps 20km LC BIDI SFP+ Transceiver

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

10Gbps 20km LC BIDI SFP+ Transceiver

Uploaded by

Copyright:

Available Formats

What are the specifications of the transceiver?

What are the specifications of the transceiver?

What are the optical characteristics of the transmitter?

What are the optical characteristics of the transmitter?

10Gbps 20km LC BIDI SFP+ Transceiver

Rev. A1, Apr.21 2015

1330nm DFB Tx/1270nm PIN Rx for PTE20-D4I-3327

AC coupling of LVPECL signals

10G Fiber Channel

CPRI Line Rate Option: 9830.4Mbps

Dongguan Mentech Optical & Magnetic Co., Ltd.