Timber Frame Shed

What could be better?
Learn the basics of

timber-framing and
get an outbuilding
in the process.
BY WILL BEEMER
Build a
Timber-Frame Shed
heres something magical about

timber-framing. Its difficult to
describe or even identify the
qualities that make it so. Maybe
its the result: a long-lasting, beautiful, strong
structure. Or perhaps its the process: teamwork, community, craftsmanship. I worked
on my first timber frame back in 1980. Forty
of us raised an entire house frame by hand in
one day, and I was hooked for life.
Like any building discipline, timber-framing
is a complex subject that cant be described
adequately in a book, let alone a magazine article. At the building school that I run, students
94
FINE HOMEBUILDING
build a 12-ft. by 16-ft. frame that involves all

the major elements of timber-framing. Building that simple frame inspires many students
to dig deeper and try their own projects. In
this article, Ill describe that same frame and
try to inspire readers as well. Please remember that for any building project, its a good
idea to consult a structural engineer and the
local building inspector.
Select the right wood
Here in the Northeast, our favorite species for

timber-framing is eastern white pine. It is
lightweight, is easy to work with hand tools,
and has one of the lowest shrinkage rates of

all available woods. Red oak and Douglas fir
also are popular woods valued for their
strength and rich red color. Southern yellow
pine is strong and a darker gold than white
pine. White oak is also strong and stable, and
it is highly resistant to rot, which makes it attractive for use in porches and outdoor structures. These five species account for the vast
majority of timber frames that are built in the
United States.
You can buy timber from a mill
that will grade it or hire a grader
to come in, but this step is not
LEARNING IN SMALL SCALE

The best way to investigate timber-framing is to
attempt a small frame that incorporates the basics
of joinery and design. The drawing below
illustrates the frames basic anatomy. Frame
sections called bents are assembled first, followed
by plates and rafters. For a materials list, go to
www.finehomebuilding.com.
5x5 rafter
3x5 collar tie
7x8 top plate
Bent
7x8 tie beam
3x5 brace
7x7 post
4x5 girt
Cut a timber frame

with a few specialized tools. Most
timber-framers
begin with a circular
saw, an electric drill,
and a few
hand tools.
4x5 door post
5x7 floor joist
Drawings: Dan Thornton
7x8 sill
OCTOBER/NOVEMBER 2004
95
CUTTING A TENON
The most common joint is the mortise and tenon.
The shoulders of the tenons, which bear the load and ultimately determine the final dimensions of the frame, must be
cut accurately. After laying out the tenon 1 , set the circular
saw to the depth of the shoulder; then make an accurate cut
on the shoulder line. Kerf the rest of the shoulder to the end
of the tenon 2 . (Be aware that if the timber isnt square,
the sawblade depth to the tenon could change from one
side to the other.) Knock out the waste with a hammer
before final paring. With a rabbet plane and/or timberframing chisel, pare the tenon to its lines 3 , then cut the
tenons opposite side. After cutting and beveling the shoulder
4 , taper and chamfer the
tenons edges so that it wont
bind in the mortise. Use a combination or framing square to
check tenon thickness and distance from the reference surface.
S Q U A R E - R U L E L AY O U T
Timbers usually arrive on site roughly square and nominally

dimensioned. Square-rule layout compensates for these
expected inconsistencies. On each timber, the straightest
two adjacent sides that are most square to each other are
marked as reference faces. All joinery measurements are
made from these faces; any discrepancies in a timbers
dimensions are canceled by cutting a housing or shoulder
on the joints mating surface.
Reference faces
Housing
Shoulder
always required. Our local inspector (and code)

requires only that timber be produced by a
state-registered mill, that the timber be stamped
for species (but not grade), and that the timbers be structurally sized as if they were #2.
How a timber frame works
A typical timber frame consists of posts (vertical members), beams (or girts, horizontal
spanning members), and braces (for racking
96
FINE HOMEBUILDING
resistance). Ideally, the timber frame should be

designed to make all joints carry only compressive loads after the frame is raised. This
way, the mating surfaces, or shoulders of the
joints, can handle the weight efficiently, and
the tenons and pegs arent subject to tensile
forces that try to pull them apart. The main
function of the pegs (also called pins or trunnels) is to draw the joint up tight during assembly and hold the joint together during
raising. Diagonal braces help to stiffen the

frame and to reduce stresses in the joints.
Timbers often are cut in a shop and brought
to the site for assembly prior to raising day.
They can be assembled either as bents, which
usually run across the short dimension of the
building (perpendicular to the ridge), or as
walls, longitudinal assemblies running parallel to the ridge. The method that you use
depends on the raising method (crane or
CUTTING A MORTISE
After drawing the layout lines, cut the edges with a chisel to
keep tearout to a minimum. I use a 112-in. auger bit in a
heavy-duty 12-in. electric drill 1 . (If auger bits are hard to
find, you can use self-feeding Forstner-type bits, but youll
have to back out and clean the hole frequently to avoid getting stuck.) To make sure Im drilling plumb and square to the
timber surface, I bolted a plywood bracket and bulls-eye level
to the drill motor housing. After roughing out the mortise
with the drill, I go back with the proper-width chisel and clean
it out 2 . Use a 3-lb. mallet to drive the chisel down the ends
of the mortise (thus severing the grain), and then use hand
power and a little body weight to pare down the sides 3 .
Alternate between cutting the end grain and paring down the
sides, and always keep the bevel of the chisel toward the
inside of the mortise. Use a combination or framing square to
check the width and squareness of the mortise 4 . After the
mortise is complete, cut the housing (if there is one) either by
roughing it out with an ax or kerfing with a circular saw.
Common timberframe joints

In addition to the
mortise and tenon,
the following joints
also contribute to
this frame.
Bridal joint
Rafter-peak
Housing
Rafter-plate
2
3
Wedged dovetail
Tie beam-post
Mortise and tenon

Brace-post
Drop-in housing
Joist-plate
RAISING THE FRAME

Safety comes first. Pay attention
to the raising leader; keep focused
on the job; and minimize tool use
overhead. Even so, hard hats are a
good idea. Before you start, its
wise to check the tenon sizes one
more time.
1. Assemble the sills on the foundation (drawing p. 95). Square up
the assembly, shim level, and add
remaining joists. Add temporary
planking or a plywood floor.
2. Assemble the first bent, aligning the post tenons over the sill
mortises, then work the posts
onto the tie beam while inserting
braces and girts. Raise the bent
and brace plumb.
3. Assemble and raise the second
and third bents as before.
4. Erect staging or planking across
tie beams, then lift plates to that
level. Insert the plate braces into
each post, snug up the pegs, then
place the plates onto the post and
brace tenons. Secure with pegs.
5. Raise planking to the plate level,
then assemble the first rafter and
collar tie on the ground, raise it,
and secure the tails to the plates
rafter seat with 20d nails.
6. The next five rafter sets are
passed up individually and
pegged together at the peak.
DRAW-BORE METHOD
MAKES A SNUG JOINT
When joints are drilled for pegs, the hole through
the mortise is drilled first. The tenon is inserted into
the mortise, marked, then offset by 18 in. When the
tapered peg is driven into the hole, it will draw the
mortise and tenon tight and keep them that way.
Pegs are
available in 34-in.
and 1-in.
diameters.
98
FINE HOMEBUILDING

Timber Frame Shed

Uploaded by

Copyright:

Available Formats

Timber Frame Shed

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Timber Frame Shed

Uploaded by

Copyright:

Available Formats

What are the main steps involved in assembling a timber frame?

What are the main steps involved in assembling a timber frame?

What joints are used to connect the different timber frame components?

What joints are used to connect the different timber frame components?

What could be better?

Learn the basics of

heres something magical about

build a 12-ft. by 16-ft. frame that involves all

Here in the Northeast, our favorite species for

and has one of the lowest shrinkage rates of

LEARNING IN SMALL SCALE

7x8 top plate

7x8 tie beam

Cut a timber frame

5x7 floor joist

Drawings: Dan Thornton

Timbers usually arrive on site roughly square and nominally

always required. Our local inspector (and code)

resistance). Ideally, the timber frame should be

raising. Diagonal braces help to stiffen the

Common timberframe joints

Mortise and tenon

RAISING THE FRAME

You might also like