Agitator Manual Chemineer PDF

Manual No. 812.
01
Installation, Operation and Maintenance Manual

MRD and MRP Agitators
(Case Size 11-16)
Equipment Reference:
For service and information contact:
Chemineer, Inc. Chemineer

5870 Poe Ave, 7 Cranmer Road
Dayton, OH 45414 West Meadows
Derby, UK
DE21 6XT
Toll Free: 1 (800) 643-0641
Phone: 1 (937) 454 3200 Phone: +44 (0) 1332 363175
Fax: 1 (937) 454 3379 Fax: +44 (0) 1332 290323
E-mail: [email protected] E-mail: [email protected]

[email protected] [email protected]
Web: www.chemineer.com Web: www.chemineer.com

MR AGITATOR
TABLE OF CONTENTS
A. PRODUCT NOMENCLATURE ........................................................................... 1
B. INITIAL INSPECTION ......................................................................................... 2
C. CHEMINEER ASSISTANCE ............................................................................... 3
D. SAFETY ................................................................................................................... 4
D.1 SAFETY SYMBOLS................................................................................................... 4
D.2 VESSELS..................................................................................................................... 5
D.3 FASTENERS ............................................................................................................... 5
D.4 CE MARKING (WHERE APPLICABLE) ................................................................. 5
D.5 SAFETY CHECKLIST ............................................................................................... 6
D.6 DISPOSAL .................................................................................................................. 7
E. STORAGE ............................................................................................................... 8
E.1 SHORT-TERM INDOOR STORAGE ........................................................................ 8
E.2 OUTDOOR OR LONG-TERM INDOOR STORAGE............................................... 8
E.3 CUSTOMER RESPONSIBILITY............................................................................. 10
F. BEAM MOUNTING............................................................................................. 11
F.1 DESCRIPTION OF AGITATOR LOADS................................................................ 11
F.2 STRUCTURAL SUPPORT STEEL DESIGN GUIDELINES ................................. 12
G. AGITATOR INSTALLATION ........................................................................... 18
H. SEAL INSTALLATION - AUXILIARY STUFFING BOX ............................. 21

H.1 INTEGRAL-TO-FLANGE STUFFING BOX DESIGN........................................... 21
H.2 BOLT-IN STUFFING BOX DESIGN (CAST HOUSING) ..................................... 23
H.3 BOLT-IN STUFFING BOX DESIGN (FABRICATED HOUSING)....................... 25
I. SEAL INSTALLATION - AUXILIARY LIP SEAL ........................................ 27
J. TAPER BORE COUPLING AND GEAR DRIVE INSTALLATION ............ 29

J.1 PREPARING THE GEARBOX FOR INSTALLATION ......................................... 29
J.2 SHAFT TAPER COUPLING INSTALLATION...................................................... 30
J.3 GEARBOX INSTALLATION .................................................................................. 31
K. MOTOR INSTALLATION.................................................................................. 33
K.1 MOTOR WEIGHTS .................................................................................................. 33
K.2 MOTOR INSTALLATION ....................................................................................... 33
L. SHAFT RUNOUT ................................................................................................. 35
M. HANDHOLE COVER INSTALLATION .......................................................... 36
IOM Manual, Chemineer Page i

June 2010
MR AGITATOR
N. IMPELLERS ......................................................................................................... 37
N.1 MATCH-MARKING................................................................................................. 37
N.2 IMPELLERS - INSTALLATION ............................................................................. 38
N.3 IMPELLERS – STYLES ........................................................................................... 39
N.4 IMPELLERS – COATED / RUBBER COVERED................................................... 46
O. OPTIONS............................................................................................................... 48
O.1 IN-TANK COUPLING.............................................................................................. 48
O.2 STEADY BEARINGS............................................................................................... 51
O.3 ANCHOR BOLTS ..................................................................................................... 60
O.4 COOLING SYSTEM................................................................................................. 61
P. LUBRICATION .................................................................................................... 62
P.1 MOTOR - LUBRICATION....................................................................................... 62
P.2 GEARBOX - LUBRICATION.................................................................................. 63
P.3 SHAFT SEALS - LUBRICATION ........................................................................... 65
P.4 STEADY BEARINGS - LUBRICATION ................................................................ 65
Q. OPERATION......................................................................................................... 66
Q.1 AGITATOR OPERATION ....................................................................................... 66
Q.2 MOTOR - OPERATION ........................................................................................... 67
Q.3 SHAFT SEALS - OPERATION................................................................................ 68
Q.4 STEADY BEARINGS - OPERATION..................................................................... 69
Q.5 LUBRICANT WATER COOLING - OPERATION ................................................ 69
Q.6 CHECKLIST.............................................................................................................. 70
Q.7 TROUBLE-SHOOTING ........................................................................................... 71
R. MAINTENANCE –AUXILIARY SEALS .......................................................... 72
R.1 MAINTENANCE – INTEGRAL-TO-FLANGE STUFFING BOX......................... 72
R.2 MAINTENANCE – BOLT-ON STUFFING BOX (CAST HOUSING) .................. 74
R.3 MAINTENANCE – BOLT-ON STUFFING BOX (FABRICATED HOUSING) ... 76
R.4 MAINTENANCE – AUXILIARY LIP SEAL .......................................................... 78
R.5 GEAR DRIVE ........................................................................................................... 79
R.6 MAINTENANCE - STEADY BEARING ................................................................ 84
S. ITEMS LIST.......................................................................................................... 87
T. APPENDIX I.......................................................................................................... 93
Page ii IOM Manual, Chemineer

June 2010
MR AGITATOR
LIST OF FIGURES
FIGURE 1. MAIN BEAM / GUSSET ORIENTATION ......................................................... 13
FIGURE 2. ANGULAR DEFLECTION DIAGRAM ............................................................. 13
FIGURE 3. OPEN TANK BEAM MOUNTING – MRD........................................................ 14
FIGURE 4. OPEN TANK BEAM MOUNTING – MRP ........................................................ 15
FIGURE 5. MRD AGITATOR ASSEMBLY.......................................................................... 19
FIGURE 6. MRP AGITATOR ASSEMBLY .......................................................................... 20
FIGURE 7. AUXILIARY STUFFING BOX........................................................................... 22
FIGURE 8. AUXILIARY STUFFING BOX (CAST HOUSING) .......................................... 24
FIGURE 9. AUXILIARY STUFFING BOX (FABRICATED HOUSING) ........................... 26
FIGURE 10. AUXILIARY LIP SEAL ...................................................................................... 27
FIGURE 11. VENT PLUG ACTIVATION............................................................................... 29
FIGURE 12. SHAFT COUPLING INSTALLATION............................................................... 30
FIGURE 13. AGITATOR LIFTING SYSTEM......................................................................... 31
FIGURE 14. FITTING THE COUPLING ................................................................................. 34
FIGURE 15. HANDHOLE COVER INSTALLATION (CASE SIZES 11-14)........................ 36
FIGURE 16. HANDHOLE COVER INSTALLATION (CASE SIZE 15-16) .......................... 36
FIGURE 17. HUB AND PIN KEY DETAIL ............................................................................ 38
FIGURE 18. STYLE P-4 IMPELLER ....................................................................................... 39
FIGURE 19. STYLE HE-3 IMPELLER.................................................................................... 40
FIGURE 20. STYLE XE-3 IMPELLER.................................................................................... 41
FIGURE 21. STYLE S-4 IMPELLER ....................................................................................... 42
FIGURE 22. STYLE D-6, CD-6, BT-6 IMPELLER ................................................................. 43
FIGURE 23. STYLE SC-3 IMPELLER .................................................................................... 44
FIGURE 24. STYLE MAXFLO W IMPELLER....................................................................... 45
FIGURE 25. THRUST BOLT IMPELLER ATTACHMENT .................................................. 47
FIGURE 26. IN-TANK COUPLINGS ...................................................................................... 49
FIGURE 27. IN-TANK COUPLINGS (CONTINUED) ........................................................... 50
FIGURE 28. BRACKET STEADY BEARING ........................................................................ 51
FIGURE 29. CUP TRI-POD STEADY BEARING .................................................................. 53
FIGURE 30. TRIPOD STEADY BEARING............................................................................. 56
FIGURE 31. PAD STEADY BEARING ................................................................................... 58
FIGURE 32. ANCHOR BOLT ASSEMBLY............................................................................ 60
FIGURE 33. COOLING COVER .............................................................................................. 61
FIGURE 34. AUXILIARY STUFFING BOX........................................................................... 73
FIGURE 35. 6 – RING STUFFING BOX (CAST HOUSING) ................................................ 75
FIGURE 36. 6 – RING STUFFING BOX (FABRICATED HOUSING) ................................. 77
FIGURE 37. AUXILIARY LIP SEAL ...................................................................................... 78
FIGURE 38. SIMPLE DISASSEMBLY DEVICE.................................................................... 83
IOM Manual, Chemineer Page iii

June 2010
MR AGITATOR
LIST OF TABLES
TABLE 1. DISPOSAL OF GEARBOX COMPONENTS....................................................... 7

TABLE 2. D-STYLE MOUNTING DIMENSIONS ............................................................. 16
TABLE 3. P-STYLE MOUNTING DIMENSIONS .............................................................. 16
TABLE 4. RECOMMENDED BEAM SIZES ....................................................................... 17
TABLE 5. TYPICAL NLGI NO. 2 GREASES...................................................................... 63
TABLE 6. TYPICAL LUBE OILS ........................................................................................ 64
TABLE 7. START UP CHECK LIST.................................................................................... 70
TABLE 8. TROUBLE-SHOOTING GUIDE......................................................................... 71
TABLE 9. MAINTENANCE INTERVALS FOR GEARBOXES ........................................ 79
TABLE 10. BRACKET, TRIPOD AND PAD STEADY BEARING WEAR SLEEVE AND
BUSHING WEAR ALLOWANCES ................................................................... 84
TABLE 11. CUP TRIPOD STEADY BEARING WEAR SLEEVE AND BUSHING WEAR
ALLOWANCES ................................................................................................... 85
TABLE 12. BOLT TIGHTENING TORQUE ......................................................................... 93
TABLE 13. BOLT TIGHTENING TORQUE (CONTD) ........................................................ 94
TABLE 14. BOLT GRADES AND MECHANICAL PROPERTIES ..................................... 95
Page iv IOM Manual, Chemineer

June 2010
MR AGITATOR PRODUCT NOMENCLATURE
A. PRODUCT NOMENCLATURE
MR Agitators
All case sizes
N
Double Mechanical
Models described in this manual are
Cartridge Seal
shaded.
NC NOTE: The case size referred to in this

Single Mechanical manual can be determined by the first
Cartridge Seal two numbers in the model designation.
For example: "14MRN-5" is a Case
Size "14" agitator. Refer to unit
NS assembly drawing or unit nameplate for
Single Mechanical model designation.
Seal
A
Stuffing Box
L
Lip Seal
NT
Split Seal
D
Drive mounted
to beams
P
Pedestal mounted
to beams
IOM Manual, Chemineer, Inc. Page 1

June 2010
INSPECTION MR AGITATOR
B. INITIAL INSPECTION
Step 1: Inspect crates. Upon receipt, inspect all crates and equipment for any damage during
shipping. If you observe any damage, please report it to your local Chemineer office or to the
factory of origin. A claim should be filed immediately with the carrier involved.
Step 2: Uncrate. Check the contents. Do not un-crate the unit until you have read all the
Installation instructions and viewed the assembly drawing shipped with the unit. Be careful in
uncrating and handling. Before discarding the crating, make sure that all agitator parts have been
removed. Correct assembly of this unit requires referring to both the unit assembly drawing and
this manual.
Step 3: Questions? Call Chemineer. If the shipment is not complete or you do not understand
what you have received, please contact your local Chemineer office immediately.
Page 2 IOM Manual, Chemineer

June 2010
MR AGITATOR ASSISTANCE
C. CHEMINEER ASSISTANCE
Chemineer maintains a fully staffed Parts and Field Service Department ready to help you with
any service requirement. When in doubt contact your local Chemineer office, or Parts/Field
Service department at the Chemineer Factory:
USA UK
Chemineer, Inc. Chemineer
5870 Poe Ave, 7 Cranmer Road
Dayton, OH 45414 West Meadows
Derby, UK
DE21 6XT
Phone: +1 (937) 454 3200 Phone: +44 (0) 1332 363175

Toll Free: 1 800 643-0641
Fax: +1 (937) 454 3379 Fax: +44 (0) 1332 290323
For your convenience, Chemineer offers the following services:
- Installation and maintenance training seminars
- Installation and start-up supervision
- Preventative maintenance planning
- Parts order service

June 2010
D. SAFETY
D.1 SAFETY SYMBOLS

Please always observe the following safety and information symbols!
Danger!
Risk of fatalities and injury
Attention!
Machine may be damaged
Note!
Useful information
All work including transportation, storage, installation, electrical connection, commissioning,

servicing, maintenance and repair must be performed only by qualified specialist personnel.
Danger!
Installation and maintenance work may only be performed when gear units are at a
standstill. The drive must be isolated and secured to prevent accidental start-up.
Tighten the drive elements or secure the parallel key before switching on.
Danger!
Only transport using the eyebolts attached to the gear unit. No additional loads may be
attached. Transportation aids and lifting gear must have an adequate load-bearing
capacity.
If geared motors have an additional eyebolt attached to the motor, this must also be used. Avoid
pulling the eyebolts at an angle. The thread of the eyebolt must be fully screwed in.
Observe all safety information, including that provided in the individual sections of this
Operating Manual. All national and other regulations on safety and accident prevention must also
be observed.
Danger!
Serious physical and property damage may result from inappropriate installation,
non-designated use, incorrect operation, non-compliance with safety information,
unauthorised removal of housing components or safety covers, and structural
modifications to the gear unit.

June 2010
MR AGITATOR SAFETY
D.2 VESSELS
All types of vessels either open or closed pose special safety challenges. It is essential that
Installers, Operators and Maintainers of the equipment understand these special hazards.
Particular safety hazards arise because the vessel is typically defined as a “Confined Space”.
This creates a number of special hazards, including the risk of having oxygen shortages. Never
enter a confined space unless you are fully trained on the procedures and have the correct safety
equipment and procedures in place.
One must not enter a confined space unless fully assured that it is safe. Typically, before entering
a vessel you should require proof of power and process fluid lock out. Always carry with you an
oxygen sensor (in order to verify a safe atmosphere), a suitable safety harnesses and lifting
equipment. Typically, a shoulder lift harness and a man-lifting crane are required (a man on the
end of a rope or a center back lift offers no safety protection). A suitable safety cover must be
provided at all time.
In cases where a vessel has been in service, tests must be made to ensure that no hazardous
products or product residues are present.
The work site is often within a designated hazardous area. Where potentially explosive
conditions exist, all efforts must be made to make the area safe before proceeding with work.
Where this is not possible, a detailed, individual hazard assessment is vital. Special working
procedures and tooling are required.
D.3 FASTENERS
Important fasteners should not be re-used. When a fastener is disturbed, always replace it with a
new one. Dispose of used fasteners. Do not keep them for re-use.
D.4 CE MARKING (WHERE APPLICABLE)
Any CE marking and associated documentation applies to the mixer only on the basis that it is an
individual product. After installation of the mixer into the mixing system, it becomes an integral
part of a larger installation. Chemineer is not responsible for the CE marking once the mixer
has been installed into the mixing system. As a standard, the mounting flange has been
designed for the design conditions stated on the arrangement drawing and a fiber flange gasket
(supplied by others). Where other conditions apply, they will be stated on the assembly drawing.

June 2010
D.5 SAFETY CHECKLIST
5 This Installation, Operation and Maintenance Manual, assembly drawings, and any
supplements must be reviewed and understood before commencing installation and
operation.
5 All site rules must be observed for the installation and operation of this mixer.
5 Ensure all external connections are made in accordance with applicable codes of practice.
5 The mixer must be earthed (connected to ground).
5 Correct rotation must be checked prior to operation.
5 Do not exceed the operating pressures, temperatures, and other conditions for which the
machine has been designed.
5 Do not operate the agitator unless all guards are securely fixed. Do not modify any
guarding. Open tanks fitted with agitators must be provided with suitable guarding to
prevent personnel contacting agitator-moving parts. The user is responsible for providing
these guards.
5 Ensure mechanical seal setting clips are disengaged before operation. These clips should
be retained for future use.
5 Ensure gas supply system, (if applicable) is correctly installed, pressurized and ready for
operation.
5 Do not touch rotating components.
5 During servicing of the mixer, the motor must be isolated from the power supply and the
supply locked out.
5 Do not operate the mixer for applications other than for its intended use.
5 Do not modify the mixer without reviewing the change with Chemineer. It is unsafe to
use non-standard parts without Chemineer's approval. When in doubt, ask your local
Chemineer office.
WHEN IN DOUBT, ASK!

June 2010
MR AGITATOR SAFETY
D.6 DISPOSAL
Observe the current local regulations. In particular, lubricants must be collected and disposed of
correctly.
Table 1. DISPOSAL OF GEARBOX COMPONENTS
Gear unit components: Material:

Toothed wheels, shafts, rolling bearings, parallel keys, locking Steel
rings, …
Gear unit housing, housing components, … Grey cast iron
Radial seals, sealing caps, rubber components,… Elastomers with steel

Coupling components Plastic with steel
Flat seals Asbestos-free sealing material
Gear oil Additive mineral oil
Synthetic gear oil (rating plate code: CLP PG) Polyglycol-based lubricants
Cooling spiral, embedding material of the cooling spiral, screw Copper, epoxy, yellow brass
fittings

June 2010
STORAGE MR AGITATOR
E. STORAGE
Do not remove protective packaging, desiccant, or any protective coatings applied to the wetted
parts until the agitator is to be put into service. If the equipment is to be stored, do not stack
crates. Store in a clean dry indoor location, which is free from wide variations in temperature.
The storage area should be free from vibration and excessive heat.
Inspect for external rust at three-month intervals. Apply a rust preventative to unpainted carbon
steel surfaces to prevent corrosion during storage. If the unit has been in storage for more than
three months or subjected to adverse moisture conditions, the motor windings may have to be
dried prior to operation.
E.1 SHORT-TERM INDOOR STORAGE
The factory storage preparations are acceptable for up to nine months storage. If the storage
period will exceed nine months, see the Long-Term Indoor Storage section. The following
precautions should be followed:
• Store the gearbox in the running position and secure gear unit against falling
• Lightly grease bare metal housing surfaces and shafts
• Store in dry rooms
• Temperature must not fluctuate beyond the range of –5°C [23°F] to +40°C [104°F]
• Relative humidity less than 60%
• No direct exposure to sunlight or UV light
• No aggressive, corrosive substances (contaminated air, ozone, gases, solvents, acids,
alkalis, salts, radioactivity etc.) in the immediate vicinity
• No vibration or oscillation
E.2 OUTDOOR OR LONG-TERM INDOOR STORAGE
Note!
For storage or standstill periods in excess of 9 months, Chemineer recommends
the long-term storage option. With the long-term storage option and the use of
the measures listed below, storage for up to 2 years is possible. As the actual
influences on the unit greatly depend on the local conditions, these times should
only be regarded as guide values.
Storage of agitators and motors outdoors is not recommended. Unless specially prepared, our
equipment is supplied with the intent that it will be immediately installed and commissioned or
subject to short-term indoor storage only.

June 2010
MR AGITATOR STORAGE
Equipment subject to long-term storage can suffer extensive damage due to corrosion. Unlike
during operation, during storage the gearbox surfaces are not covered with oil and the moisture
due to condensation inside the gearbox does not evaporate. This can rapidly lead to severe rust of
the precision components causing extensive damage.
The method employed for long-term storage is to prevent the humidity/temperature changes and
airborne chemicals from making contact with the internal components of the equipment.
The methods described below provide protection but cannot avoid some level of degradation of
the equipment.
• Store in the running position and secure gear unit against falling
• Transportation damage to the external paint must be repaired. Check that a suitable rust
inhibitor is applied to the flange bearing surfaces. If necessary apply a suitable rust
inhibitor to the surfaces.
• Gear units with the long-term storage option have VCI corrosion protection agents added
to the gear oil. (See label on gear unit)
• The sealing band in the vent plug must not be removed during storage. The gear unit
must remain sealed tight.
• Store in a dry place.
• In tropical regions, the drive unit must be protected against damage by insects
• Temperature must not fluctuate beyond the range of –5°C [23°F] to +40°C [104°F]
• Relative humidity less than 60%
• If the relative humidity is <50% the gear unit can be stored for up to 3 years.
• No direct exposure to sunlight or UV light
• No aggressive, corrosive substances (contaminated air, ozone, gases, solvents, acids,
alkalis, salts, radioactivity etc.) in the immediate vicinity
• No vibration or oscillation
Measures before commissioning the gearbox

• If the storage or standstill period exceeds 2 years or the temperature during short-term
storage greatly deviates from the standard range, the lubricant in the gear unit must be
replaced before commissioning.
• If the gear unit is completely filled, the oil level must be reduced before commissioning.
E.2.1 To prevent from corrosion:

Extreme temperatures can cause the oil volume to change. To prevent oil leakage through the
seals, it is recommended to reduce the oil capacity if it is known the temperature will vary
greatly throughout the storage period.

June 2010
STORAGE MR AGITATOR
E.2.2 To protect elastomers:

Elastomers will age, can stick or take set. In order to prevent the elastomers from sticking,
regularly rotate shafts in order to redistribute lubricants. Protect the equipment from direct
sunlight and from ozone to minimize the rate of aging of the elastomers.
E.2.3 To avoid false brinelling:
Rotate the motor and gear drive shafts 10 to 15 revolutions at least once per month to reduce the
possibility of false brinelling of the bearings and to re-distribute bearing grease.
Other problems include vibration related damage. Do not store equipment in a manner that
subjects it to vibration.
Motor space heaters, if installed, should be energized during the storage period.
Note!
When the equipment is to be stored in a strong chemical environment or near
salt-water, protection procedures should be executed immediately upon receipt
of the equipment.
E.3 CUSTOMER RESPONSIBILITY

To ensure the original quality of the Chemineer equipment prior to commissioning after storage,
all components must be inspected by an authorized Chemineer Service Engineer. Any sub
assemblies not manufactured by Chemineer must be inspected by that part
supplier/manufacturer’s authorized service personnel. Chemineer is not responsible for the cost
of such a service.
Because storage location and other unknown site factors are beyond Chemineer’s control,
Chemineer will not accept any liability for damage to the equipment during the storage
period.

June 2010
MR AGITATOR MOUNTING
F. BEAM MOUNTING
MRD and MRP (open tank) style units usually mount separately from the tank on either a steel
structure or a concrete slab over the tank. D style units may include an auxiliary shaft seal as an
option. Refer to the agitator assembly drawing for minimum required mounting height to allow
for servicing the seal.
The most frequent cause of mechanical difficulty with an agitator is improper mounting. It is
imperative to heed the following guidelines:
1. The agitator extension shaft is designed to run in a true vertical position.

2. Do not angle or side mount the agitator unless it was specifically designed for angle
mounting by Chemineer.
3. Do not mount on a surface that is not flat and horizontal.
4. Start up of the agitator with the turbine impacted in solids is beyond the scope of these
recommendations.
5. The mounting structure must be rigid enough to meet the requirements described in
section F.1 and F.2 below.
F.1 DESCRIPTION OF AGITATOR LOADS
During operation of the agitator, the fluid motion in the vessel produced by the rotation of the
turbine impeller can exert significant forces and moments on the agitator extension shaft. The
forces and moments produced by the turbine rotating in a fluid are; torque, turbine thrust (up or
down) and turbine hydraulic (side) force.
The hydraulic forces acting on the turbine generate moments, which act on the shaft and are
transmitted to the agitator drive. Because of the random nature of the forces and the rotation of
the shaft, the direction of these forces is constantly changing.
A pitched blade or axial flow turbine will impart an upward or downward thrust depending on if
it is a down or up pumping turbine, respectively. The thrust force is generally less than the
weight of the unit.
Due to the turbulent conditions within the agitated fluid, the actual operating torque, thrust and
moment loads can show up to 20% variability over those shown on the assembly drawings
supplied with the agitator.
The agitator has been designed to accommodate all of the forces mentioned, and as a result, the
forces are transmitted directly to the mounting support. The support structure must be rigid
enough to support the agitator weight and the live agitator reactions resulting from the torque,
thrust and bending moment. The structure should be sufficiently rigid that, assuming a perfectly
rigid agitator extension shaft, the structure deflection will not cause the impeller end of the shaft
to deflect more than 2.6 mm per meter of shaft length. See Figure 2 on page 13.

June 2010
MOUNTING MR AGITATOR
Particular attention should be given to reducing the torsion of the support beams local to the
agitator mounting in both the X and Y directions. Lateral beams adjacent to the agitator mount
should be sized the same as the longitudinal spans. Gussets of sufficient thickness should be used
on the beam structure under the agitator mounting plate to insure full load transfer from the
agitator mount to the support structure. See Figure 1 on page 13.
F.2 STRUCTURAL SUPPORT STEEL DESIGN GUIDELINES

The following Design Guidelines should be followed while designing the support structure:
1. The minimum natural flexural frequency of the agitator support structure should be at
least five times the maximum impeller rpm.
2. All structural steel should be fabricated and erected in strict accordance with the latest
A.I.S.C. specifications unless local code supersedes this specification.
3. Unless otherwise noted, all structural steel shapes and plates should conform to ASTM
A529; structural tubing should be ASTM A500, Grade B.
4. Unless otherwise noted, all bolted connections should be designed as bearing type
connections.
5. All bolts shall be tightened to within 70% of their minimum tensile strength.
6. Unless the process conditions, environmental conditions, or local codes prohibit, all
bolting shall be galvanized or zinc plated carbon steel.
See Table 4, page 17, for recommended beam sizes. Values in this table are keyed to the
gearbox model, case size, and tank diameter. Select the appropriate beam size for your
application. Beams of equivalent, or greater, section modulus and moment of inertia and/or
modulus of elasticity can be used. See Figure 3, page 14 for D style or, Figure 4, page 15 for P
style.
THIS INFORMATION IS INTENDED AS A GUIDE, AND DOES NOT RELIEVE

THE USER OF COMPLETELY ANALYZING THE ENTIRE MOUNTING
SYSTEM. EXTREME APPLICATIONS OR DESIGNS MAY REQUIRE
SUPPORT STIFFNESS GREATER THAN THE RECOMMENDATIONS
PROVIDED HEREIN. CONSULT CHEMINEER INSIDE SALES FOR DESIGN
GUIDANCE.

June 2010
Figure 1. Main Beam / Gusset Orientation
Figure 2. Angular Deflection Diagram

June 2010
Figure 3. Open Tank Beam Mounting – MRD

June 2010
Figure 4. Open Tank Beam Mounting – MRP

June 2010
Table 2. D-STYLE MOUNTING DIMENSIONS
CASE
A B C D E F
SIZE
0.88" 18.00" 20.00" 8.00" 8.00" 10.00"
11/12 MR
(22.2 mm) (457 mm) (508 mm) (203.2 mm) (203.2 mm) (254 mm)
1.00" 22.50" 25.00" 10.00" 9.75" 12.75"
13/14 MR
(25.4 mm) (584 mm) (635 mm) (260.4 mm) (247.7 mm) (323.9 mm)
1.00" 28.00" 19.50" 12.75" 10.75" 6.25"
15/16 MR
(25.4 mm) (711.2 mm) (495.3 mm) (323.9 mm) (273.1 mm) (158.8 mm)
Table 3. P-STYLE MOUNTING DIMENSIONS
CASE
A G H J
SIZE
0.88" 13.50" 11.75" 5.88"
11/12 MR
(22.2 mm) (342.9 mm) (298.5 mm) (149.2 mm)
1.00" 16.00" 14.00" 7.00"
13/14 MR
(25.4 mm) (406.4 mm) (355.6 mm) (177.8 mm)
1.00" 16.00" 14.00" 7.00"
15/16 MR
(25.4 mm) (406.4 mm) (355.6 mm) (177.8 mm)

June 2010
Table 4. RECOMMENDED BEAM SIZES
TANK DIAMETER Ft (m)

CASE SIZE
4 (1.22) 6 (1.83) 8 (2.44) 10 (3.05) 15 (4.57) 20 (6.10) 25 (7.62)
11/12 MR C5 X 6.7 C6 X 8.2 C7 X 9.8 C8 X 11.5 C12 X 20.7 C15 X 33.9 C15 X 50
13/14 MR * C7 X 9.8 C8 X 11.5 C12 X 20.7 C15 X 33.9 MC18 X 42.7 *

15/16 MR * W8 X 10 W10 X 12 W12 X 16 W16 X 31 * *
* Consult Factory American Std. Channel Channel to BS4 Pt.1

C = American Standard Channel C4 x 5.4 102 x 51 10.42 kg/m
MC = American Standard C5 x 6.7 127 x 64 14.9 kg/m
Miscellaneous Channel
C6 x 8.2 127 x 64 14.9 kg/m
C7 x 9.8 152 x 76 17.88 kg/m
C8 x 11.5 152 x 89 23.84 kg/m
C9 x 15 178 x 89 26.81 kg/m
C12 x 20.7 254 x 89 35.74 kg/m
C15 x 33.9 381 x 102 55.1 kg/m
C15 x 50 432 x 102 65.54 kg/m

June 2010
AGITATOR INSTALLATION MR AGITATOR
G. AGITATOR INSTALLATION
Correct installation requires both the unit assembly drawing and this manual.
Note!
These instructions deal with the highest level of details required to assemble the
entire unit. However, the specific unit supplied to you may have some assembly
steps completed. Use discretion and omit these steps
1. The agitator is shipped in various crates: one for the agitator gear drive [200], one for the
shaft and impeller [500] and typically one for the motor [100]. Optional accessories,
multiple shafts, or multiple impellers may be crated separately.
Attention!
Coated/rubber covered agitator parts require special handling to avoid damage to
coatings/rubber coverings. Do not use chains or hooks on coated/covered
surfaces. Special care is required to prevent damage to edges and outside corners.
Special installation procedures are required for large one-piece impeller/extension
shaft assemblies. Contact Chemineer Field Service for instructions.
2. Remove all shipping restraints. A hoist or crane system for the lifting of the agitator parts
must be available. Refer to Figure 13, page 31 for lifting instructions. The approximate
net weight of the unit is shown on the unit assembly drawing. Since gear drives are
typically supplied with the motor un-mounted, always verify that the motor being
mounted is correct for the gear drive by checking the assembly drawing.
3. For MRP style units, install handhole cover bolts, lockwashers [1106, 1107] into the
pedestal [1101]. Refer to Section M, page 36. Torque bolts to value shown in the
APPENDIX, Page 93.
4. Install gear drive support pedestal assembly (MRP) or just the gearbox (MRD) to
mounting structure. Install mounting bolts (supplied by others) and torque to the value
shown in the APPENDIX, Page 93.

June 2010
MR AGITATOR AGITATOR INSTALLATION
Figure 5. MRD Agitator Assembly

June 2010
AGITATOR INSTALLATION MR AGITATOR
Figure 6. MRP Agitator Assembly

June 2010
MR AGITATOR SEAL INSTALLATION
H. SEAL INSTALLATION - AUXILIARY STUFFING BOX

Applicable to: MRD with auxiliary stuffing box seal
Examine Figure 7, Figure 8, and Figure 9 to determine which type of stuffing box was supplied
with your unit.
H.1 INTEGRAL-TO-FLANGE STUFFING BOX DESIGN
1. Remove gland plate [1355], split gland [1356], packing [1357] and lantern ring [1358].
2. Assemble the auxiliary stuffing box flange to the vessel with the proper gasket and bolts
(supplied by others). Do not torque the bolts at this time, finger tighten only.
3. Place packing [1357], lantern ring [1358] and gland plate [1355] over the extension shaft
and lower the extension shaft into the vessel through the auxiliary stuffing box flange.
4. If the extension shaft coupling half is not installed, the shaft may be lifted up through the
auxiliary stuffing box from inside the vessel. Block the shaft from inside the vessel such
that the extension shaft extends above the agitator drive mounting surface. Install
packing, lantern ring and gland plate over the extension shaft.
5. Install the extension shaft coupling half if required. Follow instructions in Section J,
page 29 in order to install the gearbox and taper bore coupling.
6. Install the auxiliary stuffing box flange bolts finger tight. If the bolt holes in the stuffing
box flange and the vessel flange are not properly aligned, the agitator drive will have to
be moved laterally or shimmed. If shimming is required, use full width shims under the
gear drive mounting surface to provide a solid joint for bolting the agitator drive to the
support structure.
7. Tape gland plate [1355] to the extension shaft coupling half. Attach an indicator to the
extension shaft and set the point of the indicator on the top face of the stuffing box
housing. Manually turn the flexible motor coupling to rotate extension shaft one turn.
Shim the agitator drive until the indicator reading is within .005" (.127mm) FIM (Full
Indicator Movement) maximum. Torque agitator mounting bolts to value shown in
APPENDIX, Page 93
8. In extreme cases, a tapered adapter will be required (supplied by others) to correct the
angular misalignment. Call Chemineer Field Service for assistance.
9. Attach an indicator to the extension shaft and set the point of the indicator on the inside
diameter of the stuffing box housing. Align the stuffing box housing to within .005"
(0.127 mm) FIM of the shaft centerline and then tighten the stuffing box flange bolts
(supplied by others). Torque to the value shown in APPENDIX, Page 93.

June 2010
SEAL INSTALLATION MR AGITATOR
10. Install packing, lantern ring, split gland, and gland plate [1357, 1358, 1356, 1355]. Install
gland nuts and lockwashers [1353, 1354]. Finger tighten hex adjusting nuts [1352].
11. Let the packing set for five to ten minutes so that it can cold flow and adjust to the gland
pressure. Loosen the hex adjusting nuts, then finger tighten. After starting the unit, the
packing will require adjusting. Refer to SHAFT SEALS - OPERATION.
12. Continue with the agitator installation.
Figure 7. Auxiliary Stuffing Box

June 2010
H.2 BOLT-IN STUFFING BOX DESIGN (CAST HOUSING)

1. Assemble the flange [1251] to the vessel with the proper gasket and bolts (supplied by
others).
2. If a removable coupling is supplied with the unit, lift the agitator extension shaft and
lower it into the vessel. Lift the shaft up through the mounting flange from inside the
vessel and block it in place such that the shaft extends above the gearbox mounting
surface. If a welded or shrink fit coupling is already assembled onto the shaft, the shaft
will need to be lowered down into the flange and blocked in place in this manner.
3. Place o-ring [1252] into the groove in the mounting flange [1251].
4. Install the packing housing [1314] and packing rings [1313]. Stagger each packing split
by 90° during installation. Seat each packing ring one at a time as it is installed.
5. Install the two threaded studs [1305] at 180° from each other.
6. Install nuts, lockwasher and flatwasher [1306, 1307, 1308] onto studs. Do not tighten at
this time.
7. Install two bolts, lockwashers and flatwashers [1309, 1310, 1311]. Do not tighten at this
time.
8. Install the extension shaft removable coupling (if applicable). Follow instructions in
Section J, page 29, in order to install the gearbox and taper bore coupling.
9. Attach an indicator to the extension shaft and set the point of the indicator on the inside
diameter of the stuffing box housing. Align the stuffing box housing to within .005"
(0.127 mm) FIM of the shaft centerline and then tighten bolts [1309] and nuts [1306].
Torque to the value shown in APPENDIX, Page 93.
10. Install split packing gland [1312] over threaded studs [1305] with gland clamps,
flatwashers, lockwashers, and hex adjusting nuts [1304, 1303, 1302, 1301]. The split
packing gland must be square with the packing housing [1314]. Finger tighten the hex
adjusting nuts [1301].

June 2010
Figure 8. Auxiliary Stuffing Box (cast housing)

June 2010
H.3 BOLT-IN STUFFING BOX DESIGN (FABRICATED HOUSING)

1. Assemble the flange [1251] to the vessel with the proper gasket and bolts (supplied by
others).
2. If a removable coupling is supplied with the unit, lift the agitator extension shaft and
lower it into the vessel. Lift the shaft up through the mounting flange from inside the
vessel and block it in place such that the shaft extends above the gearbox mounting
surface. If a welded or shrink fit coupling is already assembled onto the shaft, the shaft
will need to be lowered down into the flange and blocked in place in this manner.
3. Place o-ring [1252] into the groove in the mounting flange [1251].
4. Install the packing housing [1314], clamping gland [1315] and packing rings [1313]. Do
not bolt down the clamping ring at this time. Stagger each packing split by 90° during
installation. Seat each packing ring one at a time as it is installed.
5. Install the two threaded studs [1305] at 180° from each other.
6. Install gland plate, nuts and flatwasher [1355, 1306, 1308] onto studs. Do not tighten at
this time.
7. Install four flatwashers and bolts [1311, 1316]. Do not tighten at this time.
8. Install the extension shaft removable coupling (if applicable). Follow instructions in
Section J, page 29, in order to install the gearbox and taper bore coupling.
9. Tape gland plate [1355] to the extension shaft coupling half. Attach an indicator to the
extension shaft and set the point of the indicator on the inside diameter of the stuffing box
housing. Align the stuffing box housing to within .005" (0.127 mm) FIM of the shaft
centerline and then tighten bolts [1316] and nuts [1306]. Torque to the value shown in
APPENDIX, Page 93.
10. Install split gland [1356]. The split packing gland must be square with the packing
housing [1314]. Finger tighten the hex adjusting nuts [1301].

June 2010
Figure 9. Auxiliary Stuffing Box (fabricated housing)

June 2010
I. SEAL INSTALLATION - AUXILIARY LIP SEAL

Applicable to: MRD with auxiliary lip seal
1. Remove snap ring [1852] and lip seal [1853] from flange [1851].
2. Assemble the auxiliary lip seal flange to the vessel with the proper gasket and bolts
(supplied by others). Do not torque the bolts at this time, finger tighten only.
3. Lower extension shaft [400] into the vessel through the auxiliary lip seal flange. If the
extension shaft coupling half is not installed, the shaft may be lifted up through the
auxiliary lip seal from inside the tank. Block the shaft from inside the vessel such that
the extension shaft extends above the agitator drive mounting surface.
Figure 10. Auxiliary Lip Seal
4. Place the lip seal and the snap ring over the extension shaft. Assemble lip seal and snap
ring to the flange.
5. Install the extension shaft coupling half if required. Follow instructions in Section J,
page 29 in order to install the gearbox and taper bore coupling.
6. Lift the agitator drive (Figure 13, page 31).

June 2010
7. Suspend the agitator drive assembly over the extension shaft coupling half, close enough
to allow installation of coupling bolts and lockwashers [359, 360]. The coupling faces and
tenons must be clean and free of nicks or burrs. Install two bolts and lockwashers at
180o. Tighten the bolts to engage the tenon and pull the coupling faces together.
8. Lift the agitator drive assembly and the extension shaft. Remove the shaft blocking.
Install the remaining coupling bolts and lockwashers. Torque to the value shown in
APPENDIX, Page 93.
9. Lower the agitator drive assembly onto the support structure. Install the mounting bolts
(supplied by others). Do not tighten the bolts at this time.
10. Install the auxiliary lip seal flange bolts finger tight. If the bolt holes in the lip seal flange
and the vessel flange are not properly aligned, the agitator drive will have to be moved
laterally or shimmed. If shimming is required, use full width shims under the mounting
feet to provide a solid joint for bolting the agitator drive to the support structure. Torque
the agitator drive mounting bolts to the value shown in APPENDIX, Page 93. Then
torque the auxiliary lip seal flange bolts to the value shown in APPENDIX, Page 93.
11. Auxiliary lip seals do not require any adjustment or lubrication. Both Buna-N and Teflon
lip seals as supplied are not split.

June 2010
MR AGITATOR COUPLING AND GEAR DRIVE INSTALLATION
J. TAPER BORE COUPLING AND GEAR DRIVE INSTALLATION
Danger!
To prevent injury, the danger area must be generously cordoned off. Standing under
the gear unit during transport is extremely dangerous.
Attention!
Avoid damage to the gear unit. Impacts to the free ends of the shafts may cause internal
damage to the gear unit.
Use adequately dimensioned and suitable means of transportation. Lifting tackle must
be designed for the weight of the gear unit. The weight of the gear unit can be obtained
from the dispatch documents or the assembly drawings supplied with your unit.
J.1 PREPARING THE GEARBOX FOR INSTALLATION

The drive unit must be inspected and may only be installed if no transportation damage or leaks
are visible. In particular the radial seals and the sealing caps must be inspected for damage.
Thoroughly remove rust inhibitor from the drive shafts and flange surfaces before assembly. In
applications where an incorrect rotational direction may result in damage or potential risk, the
correct rotational direction of the drive shaft is to be established by test running the drive when
uncoupled and guaranteeing such for subsequent operation.
Ensure that no aggressive or corrosive substances are present in the area surrounding the
installation site or are subsequently expected during operation, which attack metal, lubricants or
elastomers.
If a vent plug is fitted, the sealing cord must be removed from the vent plug before
commissioning.
Figure 11. Vent Plug Activation

June 2010
COUPLING AND GEAR DRIVE INSTALLATION MR AGITATOR
J.2 SHAFT TAPER COUPLING INSTALLATION
1. Clean the extension shaft [400] and coupling half [351] bore and make sure that both
surfaces are free from burrs or nicks. Place key [352] in the coupling keyway to make
sure it slides freely. Install the key in the shaft keyway making sure it is properly oriented
and fully bottomed in the keyway.
Attention!
Do not apply lubricant or anti-seize compound to coupling taper. Shaft and coupling
tapers must be clean, dry and free of nicks.
2. Slide the coupling half onto the tapered shaft end until both seat firmly against each
other. Make sure that the coupling half is not hung up on the key or cocked at an angle to
the shaft.
Attention!
Avoid surface damage and bending of the shaft. Protect the tenon and the face of
the coupling. These surfaces must be perfectly clean and free of nicks.
3. Install shaft bolts:

2 Bolt Design: Install coupling washer [354]. Install bolts [357] and lockwashers [358].
Torque bolts to the value shown in the APPENDIX, Page 93.
1 Bolt Design: Install coupling washer [353]. Install bolt [355] and lockwasher [356].
Torque bolts to the value shown in the APPENDIX, Page 93.
Figure 12. Shaft Coupling Installation

June 2010
MR AGITATOR COUPLING AND GEAR DRIVE INSTALLATION
J.3 GEARBOX INSTALLATION
Danger!
To ensure that the gearbox does not get too warm and to avoid injury to
persons, observe the following during installation:
1. The surfaces of gear units or geared motors may become hot during or shortly after
operation. Attention: danger of burns!! Protection against accidental contact may
need to be installed.
2. With geared motors, the cooling air of the motor fan must be able to flow
unobstructed onto the gear unit.
3. Welding of the gear unit is prohibited. The gear unit must not be used as the earth
connection for welding work, as this may cause damage to the bearings and gear
wheels.
4. The gear unit must be precisely aligned with the drive shaft of the machine in order to
prevent additional forces from being imposed on the gear unit due to tension.
Figure 13. Agitator Lifting System
1. Lift and suspend the agitator drive assembly over the extension shaft coupling half close
enough to allow installation of coupling bolts [361]. Install two bolts at 180°. Tighten the
bolts to engage the tenon and pull the coupling faces together.

June 2010
COUPLING AND GEAR DRIVE INSTALLATION MR AGITATOR
2. Lift the agitator drive assembly and the extension shaft enough to remove shaft blocking.
Remove blocking and install the remaining coupling bolts. Torque bolts to the value
3. For MRD units only: Lower the agitator drive assembly onto the support structure. The
gear drive assembly must be level within ¼° (.05 inches per foot; 4.4 mm per meter). If
shimming is required, use full width shims under the agitator drive housing to provide a
solid joint for bolting the agitator drive assembly to the support structure. Install the
agitator drive mounting bolts (supplied by others) and torque to the value shown in the
APPENDIX, Page 93. Ignore further steps in this section. Go to the Shaft Runout
Section, page 33.
4. For MRP units only: Install the pedestal hand hole cover bolts and lockwashers [1106,
1107], and location shoulder bolt and dowel pin [1115, 1118] into the pedestal [1101].
Lower the agitator drive assembly onto the pedestal and mount with bolts, lockwashers
and nuts [1102, 1103, 1104]. Torque bolts to the value shown in the Appendix, Page 93.
Refer to the agitator assembly drawings. Continue to install the hand hole covers per
Section M, page 36.
Attention!
For retrospective painting of the gear unit, the radial seals, rubber elements, pressure
venting valves, hoses, type plates, adhesive labels and motor coupling components must
not come into contact with paints, lacquers or solvents, as otherwise components may be
damaged or made illegible.

June 2010
MR AGITATOR MOTOR INSTALLATION
K. MOTOR INSTALLATION
K.1 MOTOR WEIGHTS

The maximum permitted motor weights indicated in the table below must not be exceeded when
attaching the motor to an IEC / NEMA adapter
Maximum permitted motor weights [kg]

IEC motor size 63 71 80 90 100 112 132 160 180 200 225 250 280 315
NEMA Motor size 56C 143T 145T 182T 184T 210T 250T 280T 324T 326T 365T
Max. motor weight 25 30 40 50 60 80 100 200 250 350 500 700 1000 1500
K.2 MOTOR INSTALLATION
Assembly procedure to attach a standard motor to the IEC adapter (Option IEC)/NEMA adapter
1. Clean motor shaft and flange surfaces of motor and IEC /NEMA adapter and check for
damage. Mounting dimensions and tolerances of the motor must conform to DIN EN
50347/NEMA MG1 Part 4.
2. Push the coupling sleeve onto the motor shaft so that the motor parallel key engages into
the groove in the sleeve on tightening.
3. Tighten the coupling sleeve on the motor shaft in accordance with the motor
manufacturer’s instructions until it touches the collar. With IEC motor sizes 160, 180 and
225, any spacer bushes must be positioned between the coupling sleeve and the collar.
Certain NEMA adapters require the adjustment of the coupling in accordance with the
specifications indicated on the adhesive plate.
4. Secure the coupling half with the threaded pin. The threaded pin must be coated prior to
use with a securing lubricant e.g. Loctite 242, Loxeal 54-03 and tightened to the correct
torque. (See Appendix, Page 93 for torque values)
5. Sealing of the flange surfaces of the motor and the IEC /NEMA adapter is recommended
if the motor is installed outdoors or in a humid environment. The flange surfaces of
motor and adapter must be completely coated with surface sealant Loctite 574 or Loxeal
58-14 prior to mounting so that the flange seals after mounting.
6. Mount the motor to the IEC /NEMA adapter, do not forget to fit the gear rim or the sleeve.
(See Figure 14)
7. Tighten the IEC /NEMA adapter bolts to the correct torque. (See Appendix, Page 93 for
torque values)

June 2010
MOTOR INSTALLATION MR AGITATOR
Figure 14. Fitting the Coupling
I Gear coupling (BoWex®), one-part

II Gear coupling (BoWex®), two-part
III Gear coupling (BoWex®), two-part with spacer bush
IV Claw coupling (ROTEX®), two-part
V Claw coupling (ROTEX®), two-part with spacer bush

June 2010
MR AGITATOR SHAFT RUNOUT
L. SHAFT RUNOUT
Note!
The runout values provided in this section do not apply to the runout measurements for
shafts with steady bearings, but the method to straighten a shaft is the same regardless
of whether there is a steady bearing or not.. Refer to the steady bearing section for
maximum allowable runout value for shafts with steady bearings.
1. Check the installed extension shaft runout. Place a dial indicator on the side of the
extension shaft at the bottom. Manually turn the flexible motor coupling to rotate the
extension shaft one turn.
2. Total shaft runout should not exceed .005" per foot (0.42 mm per meter) FIM (Full
Indicator Movement) of shaft length. If the shaft runout is excessive, the shaft can be re-
straightened in the field. Rotate the shaft to the maximum positive indicator reading.
Apply heat to the shaft at a point 180º from the indicator and just below the first in-tank
shaft coupling or just below the mounting surface if there is no in-tank coupling. As heat
is applied to the shaft (do not allow surface temperature of shaft to exceed 500ºF
[260ºC]), the shaft will move toward the indicator. After the shaft has moved .030-.060"
(0.76-1.52 mm), remove the heat and the shaft will begin to move away from the
indicator. The shaft will draw more than it moved initially, and as a result will be
straightened. After each heating cycle, recheck the shaft until runout is within tolerance.
Do not heat in the same location. Move up or down 2 or 3" (50-70 mm) to avoid
reheating the same location.

June 2010
HANDHOLE COVER INSTALLATION MR AGITATOR
M. HANDHOLE COVER INSTALLATION

For case sizes 21 and 22: Install handhole covers [1105] onto pedestal. Attach flatwasher,
lockwasher and nut [1108, 1109, 1110] to previously installed bolt and lockwasher [1106, 1107]
and tighten.
Figure 15. Handhole Cover Installation (case sizes 11-14)
For case sizes 23: Install three of the four handhole covers [1135] using flatwasher, lockwasher
and nut [1138, 1139, 1130] to previously installed bolt and lockwasher [1136, 1137] and tighten.
Install the fourth cover using bolt [1141], lockwasher [1142] and flatwasher [1143].
Figure 16. Handhole Cover Installation (case size 15-16)

June 2010
MR AGITATOR IMPELLERS
N. IMPELLERS
Note!
The instructions in this section apply to standard impeller geometry. Due to the custom
nature of impeller designs for certain applications, your impeller geometry may vary
from the standard configurations shown in this manual. Use discretion and consult the
supplied customer specific drawings for installation specifics if your impellers do not
match those shown in this manual.
N.1 MATCH-MARKING
Unless otherwise specified on the unit assembly drawing, the impeller attaches to the shaft with a
key and setscrew. Refer to Figure 17, page 38. With extended shaft keyways, the keyway is
drilled at intervals for optional impeller placement.
Impeller assemblies (hub, blades, and stabilizer fins [if required]) may be match-marked. Match-
marking is used on impellers that have been balanced or as an aid for locating multiple impellers
on the shaft. Most agitators operating at or above 100 RPM have match-marked impellers. Check
the impeller parts for match-marks before assembly.
Match-marked components are marked as a function of the agitator serial number and impeller
location. Impellers are marked sequentially beginning with the bottom impeller and working up
toward the agitator mounting surface. The following example assumes an order with two
agitators, each having two 4-blade impellers with the lower impeller stabilized.
N.1.1 Markings for Serial Number XXXXXX-1
The lower impeller hub has stub blades marked 1-1, 1-2, 1-3, 1-4. The corresponding extension
blades and stabilizer fins are marked 1-1, 1-2, 1-3, 1-4 with respect to the stub blades.
The upper impeller hub has stub blades marked 1-5, 1-6, 1-7, 1-8. The corresponding extension
blades are marked 1-5, 1-6, 1-7, 1-8 with respect to the stub blades.
N.1.2 Markings for Serial Number XXXXXX-2
The lower impeller hub has stub blades marked 2-1, 2-2, 2-3, 2-4. The corresponding extension
blades and stabilizer fins are marked 2-1, 2-2, 2-3, 2-4 with respect to the stub blades.
The upper impeller hub has stub blades marked 2-5, 2-6, 2-7, 2-8. The corresponding extension
blades are marked 2-5, 2-6, 2-7, 2-8 with respect to the stub blades.

June 2010
IMPELLERS MR AGITATOR
N.2 IMPELLERS - INSTALLATION
1. Slide hub [504] up agitator shaft [400] past the desired key location.
2. Install pin key [402] in the shaft keyway so that pin extends into the drilled hole in the
keyway. Slide the hub back down agitator extension shaft, over the key, until the hub
rests on the key step.
3. Tighten setscrew [505] firmly onto the key. Torque to the value shown in Table 12, page
93. The tapped hole for the setscrew is usually a self-locking thread form. Auxiliary
fastener locking is generally not necessary.
4. Bolt extension blades [506] to the hub [504] with bolts, nuts and lockwashers [507, 509,
508]. Refer to Figure 18 through Figure 24, page 39 through 45. Bolt split blades, if
furnished, to extension blades with bolts, nuts and lockwashers [529, 531, 530]. Bolt
stabilizer fins [510], if furnished, to extension blades with bolts, nuts, and lockwashers
[511, 513, 512]. Torque bolts to the value shown in Table 12, page 93.
Attention!
Extreme care should be taken to see that bolts are properly tightened. It is recommended
that all in-tank fasteners be checked for tightness after the first two weeks of operation.
Figure 17. Hub and Pin Key Detail

June 2010
N.3 IMPELLERS – STYLES
Figure 18. Style P-4 Impeller

June 2010
Figure 19. Style HE-3 Impeller

June 2010
Figure 20. Style XE-3 Impeller

June 2010
Figure 21. Style S-4 Impeller

June 2010
Figure 22. Style D-6, CD-6, BT-6 Impeller

June 2010
Figure 23. Style SC-3 Impeller

June 2010
Figure 24. Style Maxflo W Impeller

June 2010
N.4 IMPELLERS – COATED / RUBBER COVERED

If the unit includes a coating or rubber covering on the wetted parts, follow these instructions for
installation. Refer to the unit assembly drawing.
N.4.1 One piece shaft and impeller
The shaft and impeller are usually supplied as a one-piece (welded) coated/covered assembly,
and no impeller assembly is required. If your impeller was shipped separate from the shaft,
follow the assembly instructions below.
N.4.2 Separate shaft and one piece impeller with thrust bolt impeller attachment
The impeller is supplied as a one-piece (welded) coated/covered assembly. For attachment to the
shaft, refer to Figure 25, page 47.
1. Put gasket [522] on top of hub [504].
2. Install key [420] in the shaft keyway.
3. Hoist impeller onto shaft [400], being careful not to damage the coating/covering.
4. Install snap ring [523] in the groove at the bottom of the shaft.
Attention!
Do not remove the hoist until mounting bolt assembly [522], [524], [525], and [526] are
installed.
5. Place gasket [522] on thrust plate [524].

6. Place the thrust plate over the bottom of the shaft and install mounting bolt [526] with
gasket [525]. Torque to the value shown in Table 12, page 93.
7. Remove the hoist from the impeller.
N.4.3 Removable blade type
The rubber covered removable blades are provided with patch kits in order to rubber coat the
uncoated surfaces after bolting the blades.
Carefully read the instructions provided with the kit before using it.

June 2010
Figure 25. Thrust Bolt Impeller Attachment

June 2010
IN-TANK COUPLING - INSTALLATION MR AGITATOR
O. OPTIONS
O.1 IN-TANK COUPLING

Optional in-tank couplings are available in welded (non-removable) and taper bore (removable)
construction. Couplings can be supplied with one removable half and other welded on to the
shaft.
Note!
Whenever assembly or disassembly of an agitator with an in-tank coupling is referred to
in this manual, substitute flanged drive shaft [403] and/or flanged extension shaft [404]
(Figure 26 on page 49 or Figure 27 on page 50) for all references to the agitator
extension shaft [400].
O.1.1 Assembly of Rigid, Removable, Taper Bore Coupling Half [408, 413]
1. Clean the shaft and coupling bore and make sure that both surfaces are free from burrs or
nicks. Place key [409, 414] in the coupling keyway to make sure it slides freely. Place the
key in the shaft keyway to make sure it is properly oriented and fully bottomed in the
keyway. Install the key in the shaft keyway.
2. Slide the coupling half on the tapered shaft end until both seat firmly against each other.
Make sure that the coupling half is not hung up on the key or cocked at an angle to the
shaft.
Attention!
Do not apply lubricant or anti-seize compound to shaft or coupling taper. Shaft and
coupling taper must be clean and dry prior to assembly.
3. Shaft Bolt Installation:

2 Bolt Design:
Install coupling washer [421, 424], Install bolts and lockwashers [422, 423, 425, 426].
Torque to the value shown in the APPENDIX, Page 93.
1 Bolt Design:
Install coupling washer [410, 415] and locking clip [412, 416], Install shaft bolt [418,
419]. Torque to the value shown in the APPENDIX, Page 93. Bend exposed tabs of the
locking clip around the shaft bolt head.

June 2010
MR AGITATOR IN-TANK COUPLING - INSTALLATION
4. Assemble Coupling Halves:

Connect flanged extensi on shaft [404] to flanged drive shaft [403] making sure the
match marks are lined up and the coupling faces are clean and free from burrs or nicks.
Install coupling bolts and lockwashers [405, 406] (and nuts [407] if welded construction).
Torque to the value shown in the APPENDIX, Page 93.
5. Ensure parts are fitted to the correct shaft.
Figure 26. In-Tank Couplings

June 2010
IN-TANK COUPLING - INSTALLATION MR AGITATOR
Figure 27. In-Tank Couplings (Continued)

June 2010
MR AGITATOR STEADY BEARING - INSTALLATION
O.2 STEADY BEARINGS

MR agitators may include an optional in-tank steady bearing. See the unit assembly drawing for
the steady bearing style, type of mounting, and vessel installation requirements.
Proper steady bearing operation requires the agitator extension shaft to be straight and the steady
bearing to be centered on the shaft. Refer Shaft Runout Section, page 33, for checking and
straightening the shaft. Steady bearing mountings should be located from the installed agitator
extension shaft.
O.2.1 Bracket Steady Bearing
Figure 28. Bracket Steady Bearing
1. Place the steady bearing assembly on the end of the shaft and attach it to the support
bracket (supplied by others). The support bracket should be located such that the steady
bearing assembly is centered on the shaft. Bolt the steady bearing housing [609] to the
support bracket. Tighten the bracket bolts (supplied by others) to 25% of specified torque
per the APPENDIX, Page 93.
2. Loosen setscrews [605] and remove wear sleeve [604]. Remove bushing retaining bolt
[607] and bushing [606] from steady bearing housing [609].
3. Attach a dial indicator to the shaft and set it so the point of the indicator extends inside
the steady bearing-housing bore.

June 2010
STEADY BEARING - INSTALLATION MR AGITATOR
4. Manually turn the gear drive flexible coupling half to rotate extension shaft one turn.
Shim the steady bearing housing until it is located concentric to the shaft centerline
within .050" (1.25 mm) FIM (Full Indicator Movement).
5. Install bushing, bushing retaining bolt, lockwasher, wear sleeve and setscrews [606, 607,
608, 604, 605]. See the unit assembly drawing for the position of the wear sleeve on the
shaft. Tighten the bushing retaining bolt and the setscrews.
6. With a feeler gauge check the clearance between the wear sleeve and the bushing at the
top and bottom in 90o increments. For proper angular alignment, the gap at all locations
(from top to the bottom) must be within .010" (0.25 mm) of each other.
7. If the angular alignment needs correction, repeat Steps 1 through 6.
8. Once the final steady bearing housing location has been determined, drill the steady
bearing housing and its support bracket at two locations and install roll or dowel
alignment pins (supplied by others). Torque the bracket bolts to the value shown in the
APPENDIX, Page 93.
9. Remove the wear sleeve setscrews one at a time and transfer punch a center into the
agitator shaft. Take the wear sleeve off the shaft. Spot the shaft for the setscrews using a
drill of the same diameter as the setscrews. Drill to the depth of the drill point.
10. Reinstall the wear sleeve with the setscrews over the drill spots located in Step 9. Torque
the setscrews and the bushing-retaining bolt to the value shown in the APPENDIX, Page
93. The tapped holes for the setscrews are usually a self-locking thread form. When an
auxiliary fastener locking is required, screws will be drilled and lock-wire will be
attached..
Attention!
Do not operate the agitator without the steady bearing being submerged.

June 2010
Cup Tri-Pod Steady Bearing
Figure 29. Cup Tri-Pod Steady Bearing

June 2010
1. Install the coupling [620] onto the end of the extension shaft [400] with key [623] and
bolts, lockwashers, and coupling washer [625, 626, 624]. Refer to Installation, page 48
for in-tank coupling installation.
2. Assemble the stub shaft [630], stub shaft housing [634], and retainer plate [631] with
bolts [632] and lockwashers [633]. Torque bolts to the value shown in the APPENDIX,
Page 93.
Note!
Be sure to assemble the stub shaft [630] to the retainer plate [631] before inserting into
the stub shaft housing [634]. Alignment of the stub shaft [630] to the retainer plate [631]
is crucial to future maintenance.
3. Attach legs [635] with bolts, nuts, lockwashers, and two flat washers [636, 637, 638,
639]. Do not torque the bolts at this time. Locate the steady bearing assembly so that it is
centered with the extension shaft.
4. Adjust the leg angle and steady bearing assembly height. Torque the leg bolts [636] to
value shown in the APPENDIX, Page 93. Refer to the steady bearing assembly drawing
for the proper steady bearing set dimensions.
Note!
Later in the procedure, the stub shaft housing will need to be adjusted for shaft
concentricity and parallelism. Be sure to leave room in the leg and housing slots for
future adjustment.
5. Attach the legs [635] to the vessel bottom.
Attention!
The stub shaft [630] will need to be removed periodically for future maintenance. Be
certain that there is no obstruction below the steady bearing assembly that would hinder
the stub shaft removal.
6. Attach an indicator to the coupling [620] and set the point of the indicator on the top of
the stub shaft housing [634]. Manually turn the extension shaft [400] one full turn.
Loosen the leg bolts [636] and nuts [637] and adjust the stub shaft housing [634] to
obtain 0.010” (0.25 mm) FIM (Full Indicated Movement) maximum.
7. Place the indicator point on the outside diameter of the stub shaft [630] and rotate the
extension shaft one turn. Loosen the leg bolts [636] and nuts [637] and move the stub

June 2010
shaft housing [634] until the stub shaft is located concentric to the shaft centerline within
0.050” (1.25 mm) FIM.
8. Torque the leg bolts [636] and nuts [637] to the value shown in the APPENDIX, Page 93.
9. Recheck the steady bearing alignment with the dial indicator. If the alignment needs
correction, repeat steps 6 through 8.
10. Once the final steady bearing housing location has been determined, drill the stub shaft
housing and install the dowel alignment pins [640].
11. Loosen and remove bolts and lockwashers [632, 633] anchoring the retainer plate [631]
to the stub shaft housing [634]. Re-install bolts into tapped holes at 90° in the retainer
plate. Progressively tighten these bolts around the bolt circle to remove the stub shaft
[630] from stub shaft housing.
Attention!
Tapers can disengage with a great deal of force. On larger units, the stub shaft/retainer
assembly can be very heavy. It may be advantageous to only remove half of the retainer
plate to housing bolts and use those removed to break the stub shaft taper as described
above. This will allow the stub shaft to still be held in position when it disengages.
12. Install bushing [606] into bushing housing [627] and secure with bushing retaining bolt
[628] and lockwasher [629]. With bushing installed, assemble bushing housing to
coupling [620] using bolts and lockwashers [621, 622]. Torque the bolts to the value
13. Install the stub shaft [630] through the stub shaft housing [634] and into the bushing
[606]. Attach the retainer plate [631] with bolts [632] and lockwashers [633]. Torque
bolts to the value shown in the APPENDIX, Page 93. The retainer plate has been drilled
and tapped for a NPT pipefitting, be sure to orient the plate so that the larger end of the
tapped fitting hole is facing downward.
14. The tripod steady bearing has an optional flush feature for lubrication and cooling. If the
flush is utilized, attach the flush piping to the flush hole in the retainer plate [631]. Keep
the flush plug [641] in place on the bushing housing [627]. Note: The flush inlet pressure
should be 15 to 20 psi over the vessel pressure.
15. If the flush is not utilized, remove flush plug [641] from the bushing housing [627].
Attention!
Do not operate the agitator without the steady bearing flush and bearing assembly fully
submerged.

June 2010
O.2.2 Tri-Pod Steady Bearing
Figure 30. Tripod Steady Bearing
1. Attach legs [635] with bolts, nuts, lockwashers, and two flat washers [636, 637, 638,
639]. Do not torque the bolts at this time. Locate the steady bearing assembly so that it is
centered with the extension shaft [400].
2. Adjust the leg angle and steady bearing assembly height. Torque the leg bolts [636] to
value shown in the APPENDIX, Page 93. Refer to the steady bearing assembly drawing
for the proper steady bearing set dimensions.
Note!
Later in the procedure, steady bearing housing will need to be adjusted for shaft
concentricity and parallelism. Be sure to leave room in the leg and housing slots for
future adjustment.

June 2010
3. Attach the legs [635] to the vessel bottom.

Attention!
The wear sleeve [604] and bushing [606] will need to be removed periodically for
future maintenance. Be certain that there is no obstruction below the steady
bearing assembly that would hinder their removal..
4. Attach a dial indicator to the shaft [400] and set it so the point of the indicator extends
inside the steady bearing housing bore and rotate the extension shaft one turn. Loosen the
leg bolts [636] and nuts [637] and move the housing [634] until the housing bore is
located concentric to the shaft centerline within 0.050” (1.25 mm) FIM.
5. Install bushing, bushing retaining bolt, lockwasher, wear sleeve and setscrews
[606,607,608, 604, 605]. See the unit assembly drawing for the position of the wear
sleeve on the shaft. Tighten the bushing retaining bolt and the setscrews.
6. With a feeler gage, check the clearance between the wear sleeve and the bushing at the
top and bottom in 90° increments. For proper angular alignment, the gap at all locations
(from top to the bottom) must be within 0.010” (0.25mm) of each other.
7. If the angular alignment needs correction, repeat steps 1-6.
8. Torque the leg bolts [636] and nuts [637] to the value shown in the APPENDIX, Page 93.
9. Recheck the steady bearing alignment with the dial indicator. If the alignment needs
correction, repeat steps 6 through 8.
10. Once the final steady bearing housing location has been determined, drill and install the
dowel alignment pins [640].
11. Remove the wear sleeve setscrews [605] one at a time and transfer punch a center into the
agitator shaft [400]. Take the wear sleeve [604] off the shaft. Spot the shaft for the
setscrews using a drill of the same diameter as the setscrews. Drill to the depth of the
drill point.
12. Reinstall the wear sleeve [604] with the setscrews [605] over the drill spots located in the
previous step. The tapped holes for the setscrews are usually a self-locking thread form;
auxiliary fastener locking is not necessary. Torque the bolts to the value shown in the
APPENDIX, Page 93. When auxiliary fastener locking is required, screws will be drilled
and lock-wire will be attached.
Attention!
Do not operate the agitator without the steady bearing assembly fully submerged.

June 2010
O.2.3 Pad Steady Bearing
Figure 31. Pad Steady Bearing
1. Assemble steady bearing housing [609] to the vessel pad with the proper gasket and
flange bolts (supplied by others). Tighten the flange bolts to 25% of specified torque
2. Slide wear sleeve [604] up the extension shaft to disengage from bushing [606].
3. Attach a dial indicator to the shaft and set the point of the indicator on the top face of
housing hub [609].
4. Manually turn the flexible motor coupling to rotate the extension shaft one turn. If the
runout exceeds .010" (0.25 mm) FIM (Full Indicator Movement) maximum, a tapered
adapter (supplied by others) should be installed between the housing mounting flange and
the vessel mounting pad. Call Chemineer Field Service for assistance.
5. Place the indicator point on the outside diameter of the housing hub and rotate the
extension shaft one turn. Loosen the flange bolts and move the steady bearing housing

June 2010
until it is located concentric to the shaft centerline within .050" (1.27 mm) FIM. Torque
the flange bolts to the value shown in APPENDIX, Page 93.
6. In extreme cases, the agitator drive may have to be shimmed to correct for angular
misalignment. Call Chemineer Field Service for assistance.
7. If the angular alignment needs correction, repeat the previous steps.
8. Once the final steady bearing housing location has been determined, drill the steady
bearing housing flange at two locations on or outside of the bolt circle and install roll or
dowel alignment pins (supplied by others).
9. Slide the wear sleeve down the shaft into the bushing. See the unit assembly drawing for
the position of the wear sleeve on the shaft. Tighten setscrews [605].
10. Remove the wear sleeve setscrews one at a time and transfer punch a center into the
agitator shaft. Slide the wear sleeve up the shaft and retain. Spot the shaft for the
setscrews using a drill of the same diameter as the setscrews. Drill to the depth of the drill
point.
Attention!
Cover the opening between the extension shaft and the bushing to prevent drill chips
from getting into the housing.
11. Reinstall the wear sleeve with the setscrews over the drill spots located in Step 10.
Torque the setscrews to the value shown in APPENDIX, Page 93. The tapped holes for the
setscrews are a self-locking thread form. Auxiliary fastener locking is not necessary.
Attention!
Do not operate the agitator without the steady bearing flush on or the steady
bearing assembly fully submerged.

June 2010
ANCHOR BOLTS – INSTALLATION MR AGITATOR
O.3 ANCHOR BOLTS

Anchor bolts [901] are to be located on centers as specified on the unit assembly drawing or
Figure 3 on page 14 or Figure 4 on page 15. Mount the agitator drive on the anchor bolts and
install flatwashers, lockwashers and nuts [904, 903, 902]. Torque bolts to the value shown in the
APPENDIX, Page 93.
Figure 32. Anchor Bolt Assembly

June 2010
MR AGITATOR COOLING SYSTEM
O.4 COOLING SYSTEM

Cutting ring screw threads (see Item 1, Figure 33) are located at the casing cover for the
connection of a pipe with an external diameter of 10 mm according to DIN 2353.
1. Remove the drain plug from the screw neck prior to assembly to avoid any
contamination of the cooling system. The screw necks should be connected with the
coolant circuit, which must be provided by the operator. The flow direction of the coolant
is irrelevant.
2. Make sure not to twist the screw necks during or after assembly as the cooling coil
may be damaged (see Item 3, Figure 33). You must ensure that no external forces act on
the cooling coil.
1 3
Figure 33. Cooling Cover
Danger!
Ensure that the pressure has been released from the cooling circuit before carrying
out any work on the gear unit.

June 2010
LUBRICATION MR AGITATOR
P. LUBRICATION
This section defines the proper oils and greases that must be used with this equipment.
Attention!
Check the gear drive for proper oil fill before operating.
P.1 MOTOR - LUBRICATION
The motor bearings are properly greased by the manufacturer. Motor bearings should be re-
greased at 12-month intervals when installed in clean, dry environments, or every six months for
heavy duty and dusty locations. Any good quality general-purpose grease consisting of a refined
base oil stock and a lithium, calcium, or polyurea (preferred) complex based soap, with an NLGI
No. 2 classification, will work satisfactorily. However, different greases are not always
compatible. Hence, check for compatibility of greases before you replace one with the
other. Most major oil companies offer such products, usually with extreme pressure (EP)
additives for additional protection. Table 5, page 63 lists some commonly available greases.
When re-greasing, stop the motor, remove the outlet plug and add grease according to motor
supplier’s recommendations with a hand lever gun only. Run the motor for about ten minutes
before replacing the outlet plug. Certain TEFC motors have a spring relief outlet fitting on the
fan end. If the outlet plug is not accessible at the surface of the hood, it is the spring relief type
and need not be removed when re-greasing.
Attention!
Over-greasing is a major cause of bearing and motor failure
The following actions can be taken to correct or prevent motor over-greasing and related
problems1:
1. Review motor lubrication procedures to ensure that they identify the type and quantity of
grease to use, the specific fill and drain nozzles to uncap, and the length of time motors
should be run with drain plugs off after greasing the bearings.
2. To prevent foreign materials from contaminating the grease, ensure that grease containers
are covered during periods of storage and that the nozzles and grease fittings are cleaned.
3. Determine the optimum quantity and correct type of grease required for each motor by
examining the manufacturer's recommendations and by monitoring the behavior of grease
added to motors.
4. Consider using pre-lubricated sealed bearings in applications where re-lubrication is
difficult, where contaminants can adulterate the grease, or where over-greasing might
damage safety systems.
1
US Nuclear Regulatory Commission, Information Notice No. 88-12

June 2010
MR AGITATOR LUBRICATION
P.2 GEARBOX - LUBRICATION

All gear units are filled with lubricant ready for operation when delivered. This initial filling
corresponds to a lubricant from the column for the ambient temperatures (normal version) in the
lubricant table.
P.2.1 Roller bearing greases

Table 5 shows comparable roller bearing greases from various manufacturers. The manufacturer
can be changed for a given grease type. Chemineer Field Service must be contacted in case of
change of grease type or ambient temperature range, as this may change the warranty status for
the functionality of our gear units.
Table 5. TYPICAL NLGI NO. 2 GREASES
Lubricant type Ambient

temperature
Grease -30 ... 60°C Aralub Enegrease Sheerol Mehrzweckfett Renolit Klüberplex Mobilux 2 –
(mineral oil based) (Normal version) HL 2 LS 2 AP 2 Beacon 2 FWA 160 BEM
LZV-EP 41-132
-50 ... 40°C Aralub – Spheerol – Renolit – – Alvania
SEL 2 EPL 2 JP 1619 RL 2
Synthetic grease -25 ... 80°C Aralub – Product Beacon Renolit S2 Isoflex Mobiltemp Aero Shell
SKL 2 783/46 325 Topas SHC 32 Grease 16
Renolit NCA 52 or 7
HLT 2
Petamo
GHY 133 N
Biodegradable grease -25… 40°C Aralub Biogrease Biotec – Plantogel Klüberbio Schmierfett Alvania
BAB EP 2 EP 2 2S M 72-82 UE 100 B RLB 2
Food compatible -25 ... 40°C Eural Energrease Vitalube Carum Renolit Klübersynth Mobilgrease Cassida
grease Grease FM 2 HT 330 G 7 FG 1 UH1 14-151 FM 102 RLS 2
EP 2 Grease 2
P.2.2 Lubricant table

Table 6 shows comparable lubricants from various manufacturers. The manufacturer can be
changed within a particular viscosity or lubricant type. Chemineer Field Service must be
contacted in case of change of viscosity or lubricant type, as this may change the warranty status
for the functionality of our gear units.

June 2010
LUBRICATION MR AGITATOR
Table 6. TYPICAL LUBE OILS
Lubricant type Ambient temperature
ISO VG 220 Degol Energol Alpha Spartan Renolin Klüberoil Mobilgear 630 Omala 220
-10 ... 40°C BG 220 GR-XP SP 220 EP 220 CLP 220 GEM 1-220
(Normal version) 220
Degol BG Alpha Renolin XMP 220
220 plus MW 220 CLP 220
Plus
Alpha
MAX 220
ISO VG 100 Degol Energol Alpha Spartan Renolin Klüberoil Mobilgear 627 Omala 100
-15 ... 25°C BG 100 GR-XP SP 100 EP 100 CLP 100 GEM 1-100
100 Alpha Renolin XMP 110
Degol BG MW 100 CLP 100
100 plus Alpha Plus
MAX 100
Synthetic oil ISO VG 220 Degol Enersyn Alphasyn Glycolube Renolin Klübersynth Glygoile Tiveal
(Polyglycol) - 25 ... 80°C GS 220 SG-XP PG 220 220 PG 220 GH 6-220 HE 220 S 220
220
Synthetic oil CLP HC Aral Degol – – – Renolin Klübersynth Mobil Omala

(hydrocarbons) ISO VG 220 PAS 220 Unisyn EG 4-220 SHC 630 220 HD
-40… 80°C CLP 220
Bio-degradable oil ISO VG 220 Degol Biogear Carelub – Plantogear Klübersynth- – Naturelle
-5 ... 40°C BAB 220 SE 220 GES 220 220 S GEM 2-220 Gear Oil
EP 220
Food ISO VG 220 Eural – Vitalube Gear Oil Geralyn Klüberoil Mobil DTE Cassida
compatible oil - 25 ... 40°C Gear 220 GS 220 FM 220 AW 220 4UH1-220N FM 220 Fluid
as per regulation GL 220
H1 / FDA 178.3570
Geralyn Klübersynth
SF 220 UH1 6-220
Synth. Synthetic liquid - 25 ... 60°C Aralub – Alpha Fließfett Renolit Klübersynth Glygoile Tivela
grease BAB EP0 Gel 00 S 420 LST 00 GE 46-1200 Grease 00 GL 00
UH1-220N
Klübersynth
UH1 14-1600
Note!
After changing the lubricant, and in particular after the initial filling, the oil level may change
during the first few hours of operation, as the oil galleries and hollow spaces only fill
gradually during operation. The oil level is still within the permissible tolerance.
If at the express request of the customer, an oil inspection glass is installed at an additional
charge, we recommend that the customer corrects the oil level after an operating period of
approx. 2 hours, so that when the gear unit is at a standstill and has cooled down, the oil level
is visible in the inspection glass. Only then is it possible to check the oil level by means of the
inspection glass.
The stated filling quantities are guide values. The exact quantities vary according to the exact
gear ratio. When filling, always observe the oil level screw hole as an indicator of the precise
quantity of oil.

June 2010
MR AGITATOR LUBRICATION
P.3 SHAFT SEALS - LUBRICATION
Some units are furnished with auxiliary mounted stuffing boxes with six rings of self-lubricating
packing. This packing does not require any additional lubrication for the life of the packing.
Please refer to agitator assembly drawings for seal style and packing type.
P.4 STEADY BEARINGS - LUBRICATION
Steady bearings are lubricated and cooled by the process fluid. Do not operate agitator unless
the steady bearing is submerged or there is a flush to the steady bearing.
If a Clean-In-Place (CIP) system is present, it will generally put enough liquid into the steady
bearing to ensure the bearing is adequately lubricated, during cleaning cycle.

June 2010
OPERATION MR AGITATOR
Q. OPERATION
Q.1 AGITATOR OPERATION

Chemineer agitator has been designed for your specific application. Proper operating procedures
will allow maximum performance.
The following list will aid in the safe operation of your unit.
¾ Do not operate the unit before reading and following the instructions on all tags and
nameplates attached to the unit.
¾ Do not operate the unit in a fluid with a specific gravity or viscosity higher than that for
which the unit was designed.
¾ Do not attempt to start a unit with the mixing impeller buried in solids or a "set up" fluid.
¾ Do not operate mechanical shaft seals at temperatures or pressures higher than those for
which the unit was designed. Refer to unit assembly drawing.
¾ Do not locate large pump discharges, other agitators, down comers, coils, baffles, or
other vessel internals close to the agitator impellers and extension shaft.
¾ Do not make any changes in the field (i.e. motor horsepower, agitator speed, shaft length,
impeller diameter, impeller blade width, etc.) without reviewing the change with your
local Chemineer office or Chemineer Field Service. Minor changes could upset the
dynamics and result in dramatic and potentially dangerous failures.
Should there be problems operating the unit; review the installation and the Troubleshooting
Guide, Table 8, page 71. If you are unable to resolve the problem, contact your local Chemineer
office.

June 2010
MR AGITATOR OPERATION
Q.2 MOTOR - OPERATION
Electric motors furnished on Chemineer agitators are designed to deliver their rated output
when properly installed and maintained.
Air circulation is very important to get full performance and long life from an electric motor. Do
not block the suction inlets on fan-cooled motors. Life of the motor will be decreased if its
temperature exceeds its thermal rating. The allowable temperature is stamped on the motor
nameplate.
Prior to permanently wiring the electric motor:

¾ Check nameplate data on motor to assure that the available power supply agrees with the
motor requirements. Protective devices should be the proper size and rating to safely
carry the load and to interrupt the circuit on overloads.
¾ If motor has been stored in a damp location, the windings may require drying.
¾ Do not obstruct the normal flow of ventilating air through or over the motor.
¾ Identify motor auxiliary devices such as space heaters or temperature sensors. Connect
them in proper circuits and insulate them from motor power cables.
¾ Check motor leads with connection diagrams on motor nameplate and/or conduit box so
that the proper connections are made. All motors should be installed in accordance with
the National Electric Code and local requirements.
¾ Check the gear drive output shaft rotation against the proper rotation indicated on the unit
nameplate. For standard three-phase electric motors, the rotation can be reversed by
switching any two power leads.
¾ Check operating motor amperage against motor nameplate amperage.
The motor should start quickly and run smoothly. If the motor should fail to start or make
abnormal noise, immediately shut motor off, disconnect it from the power supply, and
investigate the cause. If the problem cannot be corrected, contact your local Chemineer office for
assistance.

June 2010
MAINTENANCE MR AGITATOR
Q.3 SHAFT SEALS - OPERATION
Q.3.1 LIP SEALS

This gearbox is sealed on the output shaft [244] by two lip seals. These seals are greased at the
factory, so no service is necessary at start up for these seals.
The extension shaft lip seal or v-ring does not come pre-greased. While it is not mandatory to
grease these seals, the seals will have a lower running temperature and thus a longer life if grease
is applied prior to operation. If the process conditions allow, process-compatible grease should
be applied to the sealing surface.
All rotary lip seals will eventually need replacement as they are wearing components. Wear
rates depend on agitator input and output speeds, frequency of service, and environmental
factors. A “typical” life cannot be predicted, so periodic inspection is highly recommended.
Q.3.2 AUXILIARY STUFFING BOXES

Some units are furnished with auxiliary mounted stuffing boxes. The standard stuffing box is a
six (6) ring design with self-lubricating packing suitable for 100 psig (689 kPa) at 400oF (204oC).
At start-up, the packing should be “run-in” by tightening the hex adjusting nut one flat at a time,
allowing 15 minutes between each take-up for the packing to reseat itself before further
tightening. Repeat these adjustments at 15-minute intervals until the desired leakage is obtained.
Make periodic inspections for leakage, but do not pick up the gland unless necessary. Over
tightening wears out packing prematurely, and causes scoring and damage to the shaft.

June 2010
MR AGITATOR MAINTENANCE
Q.4 STEADY BEARINGS - OPERATION
If a steady bearing is supplied, do not operate agitator unless it is properly installed. Failure to
install a required steady bearing will cause severe damage to the agitator assembly if operated.
Do not operate agitator unless the steady bearing is submerged.
The pad and cup-tripod steady bearings have been supplied with an optional flush feature for
lubrication and cooling. If the flush is utilized, the pipe plug [641] must remain installed on the
bushing housing [627] and the inlet pressure should be maintained at 15 to 20 psi over the vessel
pressure. If the flush is not utilized, the pipe plug [641] must be removed.
Q.5 LUBRICANT WATER COOLING - OPERATION
Caution!
The drive may only be commissioned after the cooling spiral has been connected to the
cooling circuit, and the cooling circuit has been put into operation.
The coolant must have a similar thermal capacity as water (specific thermal capacity at 20°C
c=4.18 kJ/kgK). Industrial water without any air bubbles or sediments is recommended as a
coolant. The water hardness must be between 1° dH and 15° dH, and the pH value must be
between pH 7.4 and pH 9.5. No aggressive liquids should be added to the coolant!
The coolant pressure must not exceed 8 bar. The required quantity of coolant is 10
litres/minute, and the coolant inlet temperature should not exceed 40°C; we recommend 10°C.
We also recommend fitting a pressure reducer at the coolant inlet to avoid any damage due to
excessive pressure.
If there is a danger of frost the operator should add a suitable anti-freeze solution to the cooling
water.
The temperature of the cooling water and the cooling water flow rate must be supervised and
ensured by the operator.

June 2010
Q.6 CHECKLIST
Table 7. START UP CHECK LIST
Object of the check Checked on:

Is the vent plug activated or the pressure vent screwed in?
Are contact guards fitted to rotating components?
Is the cooling cover connected to the cooling circuit (if
applicable)?
Is mounting per recommendations?
Are impeller bolts properly torqued?
Are impellers submerged in any settled solids?
Has shaft runout been checked?
Has shaft rotation direction been verified?
Does gearbox have proper lubrication?

June 2010
Q.7 TROUBLE-SHOOTING
Table 8. TROUBLE-SHOOTING GUIDE
OBSERVATION POSSIBLE CAUSE ACTION
Check bearings and gears for excessive

wear. Replace worn parts. Try to find
Worn or damaged parts cause of wear. Check for water and/or
abrasives in oil, overload, incorrect
rotation, excessive shock, etc.
Overloading can cause excessive
separation of gear teeth and loud
operation. Check process fluid (specific
Overloading gravity and viscosity) vs. design
conditions. Check agitator speed and
Noisy Operation
impeller diameter against unit assembly
drawing information.
Couplings can generate noise, which
Worn or improperly installed
seems to emanate from gear drive.
motor coupling
Check for worn parts.
Steel mounting structures often amplify
small amounts of normal noise into
Structural vibration and sound
excessive noise. This can be corrected
amplification
by adding stiffness or sound deadening
material to the structure.
Review Lubrication section of manual.
Incorrect Oil
Replace with proper oil.
Units installed in a hot area of a plant
where airflow is restricted can overheat.
Unusual ambient
Abnormal Heating Remove obstruction and if necessary
force circulate air.
Improper oil level Add or remove oil.
Remove dirt and/or product buildup
Cleanliness
from motor/gear drive.
Worn oil seals Replace defective seals.
Leaking Incorrect oil level or incorrect,
Oil escaping from
contaminated oil or unfavourable
pressure vent operating conditions. Change oil.
Drive shaft does not Fracture in gear unit or
rotate although motor is defective motor coupling or Consult Chemineer Engineering
running shrink disc slippage

June 2010
R. MAINTENANCE –AUXILIARY SEALS
R.1 MAINTENANCE – INTEGRAL-TO-FLANGE STUFFING BOX

The stuffing box is generally furnished with self-lubricating packing. If this is the case, it does
not require any additional lubrication for the life of the packing. Routine maintenance consists of
periodic inspections for leakage and tightening of gland nuts [1353]. Repacking is required when
satisfactory control over leakage is not attainable. Check to ensure your packing is self-
lubricating or is otherwise sufficiently lubricated.
R.1.1 Stuffing box Removal
Attention!
Prior to removing the agitator drive, review the agitator installation to assure that
all safety issues are resolved.
1. Lock out and disconnect all power to the gear drive motor and optional devices.
2. Depressurize and ventilate vessel.
3. Remove stuffing box packing:
Remove hex adjusting nuts [1353] and lock washers [1354]. Slide gland plate [1355]
toward the gear drive. Remove split gland [1356]. With packing tools (supplied by
others), remove three rings of packing [1357], lantern ring [1358], and the remaining
three rings of packing. The lantern ring is provided with two #8-32 tapped holes to aid in
removal.
Attention!
Never add new packing on top of the old packing, as this will cause accelerated wear and
scoring of the shaft.
Refer to the unit assembly drawing for the number and composition of the packing rings
supplied originally with your agitator.
R.1.2 Stuffing box repacking

1. Install three packing rings [1357], lantern ring [1358], three more packing rings, split
gland [1356] (holes at top), gland plate [1355], lockwashers [1354] and gland nuts
[1353]. Stagger each packing split 90°. Seat each packing ring as it is installed.
2. Tighten the gland nuts until the lockwashers are compressed. Let the packing set for five
to ten minutes so that it can cold flow and adjust to the gland pressure. Loosen the hex
adjusting nuts, then finger tighten.

June 2010
The stuffing box will require adjustment at start-up. Always strive for satisfactory sealing
with the least gland force possible. Tighten the hex adjusting nuts uniformly and gradually
(no more than one flat on the nuts every 15 minutes) until the leakage rate is acceptable. Do
not over tighten. Make sure the split packing gland remains square with the shaft. Once the
packing has been "run in", the hex adjusting nuts should be retightened on a regular basis.
This can vary from weekly to monthly depending upon the desired level of sealing and the
frequency of operation.
Figure 34. Auxiliary Stuffing Box

June 2010
R.2 MAINTENANCE – BOLT-ON STUFFING BOX (CAST HOUSING)

The stuffing box is generally furnished with self-lubricating packing. It does not require any
additional lubrication for the life of the packing. Routine maintenance consists of periodic
inspections for leakage and tightening of hex adjusting nuts [1301]. Repacking is required when
satisfactory control over leakage is not attainable.
Attention!
Remove hex adjusting nuts, lock washers, flat washers and gland clamps [1301, 1302,
1303, 1304]. Remove split packing gland [1312]. With packing tools (supplied by
others), remove packing [1313].
Attention!
1. Install packing rings [1313]. Stagger each packing split 90°. Seat each packing ring as it
is installed. Install split packing gland and gland clamps [1312, 1304]. Retain with hex
adjusting nut, lockwasher and flatwasher [1301, 1302, 1303].
2. Tighten the hex adjusting nuts. Let the packing set for five to ten minutes so that it can
cold flow and adjust to the gland pressure. Loosen the hex adjusting nuts, then finger
tighten.
packing has been "run in", the hex adjusting nuts should be retightened on a regular basis.

June 2010
Figure 35. 6 – Ring Stuffing Box (cast housing)

June 2010
R.3 MAINTENANCE – BOLT-ON STUFFING BOX (FABRICATED HOUSING)

The stuffing box is generally furnished with self-lubricating packing. It does not require any
additional lubrication for the life of the packing. Routine maintenance consists of periodic
inspections for leakage and tightening of hex adjusting nuts [1301]. Repacking is required when
satisfactory control over leakage is not attainable.
Attention!
Remove hex adjusting nuts [1301] and flat washers [1303]. Slide gland plate [1355]
toward the gear drive. Remove split gland [1356]. With packing tools (supplied by
others), remove packing [1313].
Attention!
1. Install packing rings [1313]. Stagger each packing split 90°. Seat each packing ring as it is
installed. Install split gland [1356] (holes at top) and gland plate [1355]. Retain with hex
adjusting nut and flatwasher [1301, 1303].
2. Tighten the hex adjusting nuts. Let the packing set for five to ten minutes so that it can cold
flow and adjust to the gland pressure. Loosen the hex adjusting nuts, then finger tighten.
packing has been "run in”, the hex adjusting nuts should be retightened on a regular basis.

June 2010
Figure 36. 6 – Ring Stuffing Box (fabricated housing)

June 2010
R.4 MAINTENANCE – AUXILIARY LIP SEAL

The lip seal, like any rotary shaft seal, will eventually wear and require replacement. Routine
maintenance consists of periodic inspections for leakage. Replacement is required when a
satisfactory shaft seal is no longer attainable.
R.4.1 Lip seal removal
3. Remove snap ring [1852] and lip seal [1853] from flange [1851].
4. Lip seal will need to be cut for removal from shaft. Snap Ring Can remain on the shaft
until the new lip seal has been installed.
R.4.2 Lip seal replacement
1. Place the new pre-split lip seal into the flange.
2. Reinstall the snap ring [1852] into flange [1851].
3. Auxiliary lip seals do not require any adjustment or lubrication.
Figure 37. Auxiliary Lip Seal

June 2010
R.5 GEAR DRIVE
R.5.1 Maintenance Intervals
Table 9. MAINTENANCE INTERVALS FOR GEARBOXES
Service and Maintenance

Intervals Service and Maintenance Work
At least every six months – Visual inspection
– Check for running noises
– Check oil level
– Re-grease
Every 10000 operating – Change oil (if filled with synthetic oil, this period is doubled)
hours, at least every 2 years Reduction of lubricant replacement interval under extreme
operating conditions (high humidity, aggressive environment
and high temperature fluctuations)
– Check the cooling coil for deposits
At least every 10 years – General overhaul
R.5.2 Maintenance Work
Attention!
Service and maintenance work must only be performed by qualified personnel.
Installation and maintenance work must only be performed when gear units are at
a standstill. The drive must be isolated and secured to prevent accidental start-up.
R.5.2.1 Visual inspection
The gear unit must be checked for leaks. In addition, the gear unit must be inspected for external
damage and cracks in the hoses, hose connections and rubber buffers. Have the gear unit repaired
in case of leaks, e.g. dripping gear oil or cooling water, damage or cracks. Please contact the
Chemineer Field Service department.
R.5.2.2 Check for Running Noises

If the gear unit produces unusual running noises and/or vibrations, this could indicate damage to
the gear unit In this case the gear should be shut down and a general overhaul carried out.
R.5.2.3 Check the Oil Level
1. The oil level may only be checked when the gear unit is at a standstill and has cooled
down. The gear unit must be secured to prevent accidental switch-on.

June 2010
2. The oil level screw corresponding to the version must be screwed out.
Note!
At the first oil level check a small amount of oil may escape, as the oil level may
be below the lower edge of the oil level hole.
3. The maximum oil level is the lower edge of the oil level hole. The minimum oil level is 4
mm below the oil level hole. If the oil level is too low, this must be corrected using the
correct type of oil. An oil level glass is available instead of the oil level screw
4. Cap screw with dipstick (optional) and all other loosened screws must be correctly re-
tightened.
R.5.2.4 Regreasing
For some IEC adapters, the outer roller bearing must be regreased with approx. 20-25g of grease
via the grease nipple provided
R.5.2.5 Changing the Oil
1. Place the drip tray below the oil drain screw or the oil drain cock
2. Completely remove oil level screw, screwed sealing plug with dipstick if an oiL level
tank is being used and oil drain screw.
Danger!
Warning: Hot oil!
3. Drain all the oil from the gear unit.

4. If the screw lock coating of the oil drain screw or oil level screw is damaged in the
thread, a new oil level screw must be used or the thread cleaned and coated with securing
lubricant, e.g. Loctite 242, Loxeal 54-03 prior to inserting. The seal ring must be replaced
if damaged.
5. Support the seal ring, insert the oil drain screw into the hole and tighten to the correct
torque! (See Appendix, Page 93 for torque values)
6. Using a suitable filling device, refill with oil of the same type through the oil level hole
until oil emerges from the oil level hole. (The oil can also be filled through the pressure
vent screw or a sealing plug located higher than the oil level).
7. Wait at least 15 minutes, or at least 30 minutes if an oil level tank is used, and then check
the oil level.

June 2010
R.5.2.6 General Overhaul

The gear units must be completely dismantled. The following work must be carried out:
• Clean all gear unit components
• Examine all gear unit components for damage
• All damaged components must be replaced
• All roller bearings must be replaced
• Replace all seals, radial seals and Nilos rings
• Replace plastic and elastomer components of the motor coupling
The general overhaul must be carried out by a specialist workshop with appropriate
equipment and qualified specialist personnel.
R.5.3 MRP Agitator drive removal
3. Remove handhole covers.

Remove mounting bolts, lockwashers, and nuts [1102, 1103, 1104]. With a hoist or crane
system, lift the agitator drive assembly (Figure 13, page 31) above the pedestal [1101]
sufficiently to allow the shaft to be blocked in place. Remove coupling half bolts [360]. Refer to
4. Figure 12, page 30.
5. Remove the agitator drive to a suitable service area
R.5.4 MRD Agitator drive removal

Remove mounting bolts, lockwashers, and nuts (supplied by others). With a hoist or crane
system, lift the agitator drive assembly (Section J, page 31) above the mounting structure
sufficiently to allow the shaft to be blocked in place. Remove coupling half bolts [360]. Refer to
3. Figure 12, page 30.

June 2010
4. Remove the agitator drive to a suitable service area
R.5.5 Preparation for disassembly
1. Clean external surfaces and drain the oil.
2. Remove motor [100] from gearbox.

R.5.6 Removing the shrink fit output shaft coupling (11-14 MR only)
Attention!
Do not subject the gear unit to harmful axial forces or shock loads when fitting the hubs.
1. Remove the coupling bolt and washer from the output shaft.
2. Use an appropriate puller to pull the coupling from the output shaft (Figure 38). Apply
force against the end of the exposed output shaft while pulling on the coupling. Do not
apply a blunt force to the coupling or shaft.
3. If necessary, a torch can be used to heat the coupling. A sweeping motion should be used
so as not to overheat any one area of the coupling.
R.5.7 Removing the taper fit output shaft coupling (15-16 MR only)
Attention!
Do not subject the gear unit to harmful axial forces or shock loads when fitting the hubs.
1. Bend down the tabs on the locking tab (if present) and loosen the coupling bolt, but do
not remove completely.
2. Use an appropriate puller to pull the coupling from the output shaft (Figure 38). Apply
force against the end of the exposed output shaft while pulling on the coupling. If
necessary, a gentle tap on the side of the coupling with a hammer will help loosen the
self-locking taper from the shaft.
Attention!
WARNING: The release of the taper fit can cause the coupling to suddenly pop off the
shaft and fall to the floor if not adequately restrained..

June 2010
R.5.8 Installing the shrink fit output shaft coupling (11-14 MR only)
1. The output coupling is purposefully a tight, shrink fit. Apply heat to the coupling in
order to heat it to approximately 120°C.
2. Slide the heated coupling onto the output shaft, then install the washer tight against the
coupling and the shaft to make sure the coupling is fully seated onto the shaft.
3. Allow the coupling and gearbox to cool sufficiently before continuing with the
installation.
R.5.9 Installing the taper fit output shaft coupling (15-16 MR only)
1. Re-installing the taper coupling to the gearbox is the same as installing the taper coupling
onto the extension shaft. See section J.2, Shaft Taper Coupling installation on page 30
for instructions.
Figure 38. Simple Disassembly Device

June 2010
R.6 MAINTENANCE - STEADY BEARING
R.6.1 BRACKET, TRIPOD AND PAD STEADY BEARINGS
In-tank steady bearings will require periodic inspection and replacement of bushing and wear
sleeve [606, 604] (Figure 28 on page 51, Figure 29 on page 51, Figure 30 on page 56, or Figure
31 on page 58).
It is recommended that the steady bearing fasteners be checked for tightness and the bushing and
wear sleeve for wear after the first two weeks of operation. Unless otherwise specified the
recommended wear allowance is:
Table 10. BRACKET, TRIPOD AND PAD STEADY BEARING WEAR SLEEVE
AND BUSHING WEAR ALLOWANCES
SHAFT UP TO 3" LARGER THAN 3"

DIAMETER (76.2mm) (76.2mm)
WEAR SLEEVE .040" (1mm) .060" (1.5 mm)
BUSHING .120" (3mm) .180" (4.5 mm)
The wear sleeve and bushing should be replaced in sets.

Attention!
Lock out and disconnect all power to the gear drive motor, any optional devices, and
depressurize vessel before servicing this equipment.
1. Loosen setscrew [605] and slide wear sleeve [604] off the shaft.
2. Unbolt the housing from the bracket or tripod (Not applicable to pad style).
3. Remove bushing retaining bolt and lockwasher [607, 608]. Remove the bushing from the
steady bearing housing.
4. Press a new bushing into the steady bearing housing. Install the bushing retaining bolt
and lockwasher.
Note!
Line up the clearance hole in the new bushing with the tapped hole in the
housing prior to pressing the bushing into the housing.
5. Reinstall the wear sleeve and housing/bushing assembly. Torque all fasteners to the
value shown in APPENDIX, Page 93.
Attention!
Do not operate the agitator without the steady bearing being submerged.

June 2010
R.6.2 CUP TRIPOD STEADY BEARING

In-tank steady bearings will require periodic inspection and replacement of bushing and stub
shaft [606, 630]. (Figure 29, page 53)
It is recommended that the steady bearing fasteners be checked for tightness and the bushing &
stub shaft for wear after the first two weeks of operation.
Unless otherwise specified, the recommended wear allowance is:
Table 11. CUP TRIPOD STEADY BEARING WEAR SLEEVE AND BUSHING
WEAR ALLOWANCES
SHAFT UP TO 3" LARGER THAN 3"

DIAMETER (76.2mm) (76.2mm)
WEAR SLEEVE .040" (1mm) .060" (1.5 mm)
BUSHING .120" (3mm) .180" (4.5 mm)
The stub shaft and bushing should be replaced in sets.

Attention!
Lock out and disconnect all power to the gear drive motor, any optional devices, and
depressurize vessel before servicing this equipment.
1. Remove the retainer plate [631] and the stub shaft [630] from the stub shaft housing
[634]. Remove the retainer to housing bolts and install them into the threaded holes on
the retainer plate. Progressively tighten these bolts around the bolt circle to remove the
stub shaft.
Attention!
Tapers can disengage with a great deal of force; also the stub shaft/retainer assembly can
be very heavy on larger size agitators. In order to hold the stub shaft when it disengages
use half of the supplied retainer plate bolts threaded into the stub shaft housing.
2. Unbolt the bushing housing [627] from the coupling [620]. Remove the bushing retaining
bolt [628] and lockwasher [629]. Press the bushing [606] out of the bushing housing
[627].
3. Press a new bushing into the bushing housing. Install the bushing retaining bolt and
lockwasher.
Note!
Line up the clearance hole in the new bushing with the tapped hole in the bushing housing
prior to pressing the bushing in place.

June 2010
4. Reinstall the bushing housing, new stub shaft, and retainer plate as described in the
Steady bearings installation section. Torque fasteners to the value shown in Table 12,
page 93.
5. Re-attach the flush piping (if used).

June 2010
MR AGITATOR ITEMS LIST
S. ITEMS LIST
Item# Description Qty.
100 Motor 1
200 Gear drive 1

244 output shaft 1
350 Low Speed Coupling Assembly 1

351 gear drive coupling half 1
352 key 1
353 coupling washer (1 bolt) 1
355 lockwasher 1
356 bolt 1
357 lockwasher 2
358 bolt 2
361 bolt
362 bolt 1
363 lockwasher 1
365 key 1

June 2010
ITEMS LIST MR AGITATOR
400 Extension shaft assembly 1

402 pin key 1
403-001 drive shaft (welded coupling) 1
403-002 drive shaft (removable coupling) 1
404-001 extension shaft (welded coupling) 1
404-002 extension shaft (removable coupling) 1
405 bolt
406 lockwasher
407 nut
408 rigid, removable, taper bore coupling half 1
409 key 1
410 coupling washer 1
412 locking clip 1
413 rigid, removable, taper bore coupling half 1
414 key 1
416 locking clip 1
418 shaft bolt 1
419 shaft bolt 1
420 key 1
422 bolt 2
423 lockwasher 2
425 bolt 2
426 lockwasher 2

June 2010
500 Impeller assembly

501 impeller assembly P-4
502 impeller assembly S-4
503 impeller assembly HE-3
504 hub
505 setscrew
506 extension blade
507 bolt
508 lockwasher
509 nut
510 stabilizer fin
511 bolt
512 lockwasher
513 nut
514 impeller assembly D-6, CD-6, BT-6
515 split disc
516 bolt
517 flatwasher
518 bolt
519 flatwasher
520 locking clip
521 nut
522 gasket 2
523 snap ring 1
524 thrust plate 1
525 gasket 1
526 mounting bolt 1
527 impeller assembly SC-3
528 impeller assembly Maxflo W
529 bolt
530 lockwasher
531 nut
532 impeller assembly XE-3

June 2010
600 Steady bearing assembly 1

601 bracket steady bearing 1
602 pad steady bearing 1
603-001 cup tripod steady bearing 1
603-002 tripod steady bearing 1
604 wear sleeve 1
605 setscrew, square head
606 bushing 1
607 bushing retaining bolt 1
608 lockwasher 1
609 steady bearing housing 1
610 drain plug, NPT 1
620 coupling 1
621 coupling bolt 4 to 6
622 lockwasher 4 to 6
623 key 1
625 shaft bolt 2
626 lockwasher 2
627 bushing housing 1
628 bushing retaining bolt 1
629 lockwasher 1
630 stub shaft 1
631 retainer plate 1
632 retainer plate bolt 4 to 8
633 lockwasher 4 to 8
634 stub shaft housing 1
635 leg 3
636 leg bolt 6
637 leg nut 6
638 lockwasher 6
639 flat washer 6
640 alignment pin 3
641 pipe plug (flush) 1

June 2010
700 Mounting plates 1

701 plate 4
702 bolt 4
703 lockwasher 1
704 bolt 8
705 lockwasher 8
706 plate 1
900 Anchor bolt assembly 1

901 anchor bolt 4
902 nut 4
903 lockwasher 4
904 flatwasher 4
1100 Pedestal assembly 1

1101 pedestal 1
For sizes 11 through 14only

1102 Bolt 4
1103 Lockwasher 4
1104 nut 4
1105 handhole cover 4
1106 Bolt 4
1107 Lockwasher 4
1108 Flatwasher 4
1109 Lockwasher 4
1110 Nut 4
For size 15-16 only

1130 nut 3
1135 handhole cover 4
1136 bolt 3
1137 lockwasher 3
1138 flatwasher 3
1139 lockwasher 3
1141 bolt 1
1142 lockwasher 1
1143 flatwasher 1

June 2010
1250 Mounting flange assembly 1

1251 mounting flange 1
1252 o-ring 1
1300 Auxiliary stuffing box assembly (bolt-in) 1

1301 hex adjusting nut 2
1302 lockwasher 2
1303 flatwasher 2
1304 gland clamps 2
1305 stud 2
1306 nut 2
1307 lockwasher 2
1308 flatwasher 2
1309 bolt 2
1310 lockwasher 2
1311 flatwasher 2
1312 split packing gland 2
1313 packing 6
1314 packing housing 1
1315 clamping gland 1
1316 bolt 4
1350 Auxiliary stuffing box assembly (integral) 1

1351 flanged stuffing box (6 ring) 1
1352 stud 2
1353 gland nut 2
1354 lockwasher 2
1355 gland plate 1
1356 split gland 1
1357 packing (2 sets of 3 rings) 6
1358 lantern ring 1
1359 grease fitting 1
1360 pipe plug, NPT 1
1850 Auxiliary lip seal assembly 1

1851 lip seal flange 1
1852 snap ring 1
1853 lip seal 1

June 2010
MR AGITATOR APPENDIX
T. APPENDIX I
Tighten all fasteners to values shown unless specifically instructed to do otherwise. Lubricate all fasteners
at assembly with thread lubricant or an anti-seize material. Bolt threads and contact surfaces of bolt heads
and nuts should be lubricated. Note that stainless steel and alloy fasteners can gall while being tightened.
The risk of galling or thread seizing is reduced by using lubrication, by tightening fasteners with low
rpm’s and without interruptions, and applying only light pressure. Dry fasteners, components with dirt or
dust, bolting faces with rough finish, or even some environmental factors such as heat or moisture can
effect the torque readings, and require values different than those listed in the table below.
Table 12. BOLT TIGHTENING TORQUE
SAE J429 CARBON STEEL STAINLESS STEEL

BOLT GRADE 2 GRADE 5 METRIC GRADE 300 Series Stainless Steel
SIZE METRIC GRADE 4.6 METRIC GRADE 8.8 12.9 (e.g. 304, 316)
ft-lb Nm ft-lb Nm ft-lb Nm ft-lb Nm
1/4 - 20 - - 6 8.1 - - 4.1 5.6
5/16 -18 - - 13 18 - - 8 11
3/8 - 16 - - 23 31 - - 15 20
1/2 - 13 38.0 52 55 75 - - 38 52
9/16 -12 50.0 68 79 107 - - 50 68
5/8 - 11 68.0 92 110 149 - - 68 92
3/4 - 10 120.0 163 195 264 - - 95 129
7/8 - 9 122.0 165 314 426 - - 153 207
1-8 184.0 250 470 637 - - 230 312
1-1/8 - 7 260.0 353 587 796 - - 326 442
1-1/4 - 7 368.0 499 828 1123 - - 460 624
1-3/8 - 6 482.0 654 1085 1471 - - 602 816
1-1/2 - 6 640.0 868 1440 1953 - - 800 1085
M6 x 1.00 3.8 5.1 6.9 9.4 9.7 13 4.3 5.8
M8 x 1.25 8 10 17 23 24 32 10 14
M10 x 1.50 15 20 34 45 47 63 21 28
M12 x 1.75 26 35 58 79 81 110 36 49
M16 x 2.00 64 87 145 196 202 274 89 121
M20 x 2.50 126 170 282 383 394 534 174 236
M24 x 3.00 217 664 489 664 537 728 300 407

June 2010
APPENDIX MR AGITATOR
Table 13. BOLT TIGHTENING TORQUE (CONTD)
ALLOY 600 (UNS#N06600),

ALLOY 20 (UNS#N08020),
ALLOY C4 (UNS#N06455), ALLOY C276 (UNS#N10276),
BOLT ALLOY 400 (UNS#N04400),
ALLOY G30 (UNS#N06030), ALLOY C2000 (UNS#N06200)
SIZE ALLOY 825 (UNS#N08825)
ALLOY 2205 (UNS#S32205)
ft-lb Nm ft-lb Nm ft-lb Nm

1/4 - 20 4 5.4 5 6.8 3.4 4.6
5/16 -18 8 11 10 14 7 9
3/8 - 16 15 20 18 25 12 17
1/2 - 13 36 49 45 61 30 41
9/16 -12 52 70 65 88 43 59
5/8 - 11 72 97 89 121 60 81
3/4 - 10 127 172 159 215 106 143
7/8 - 9 205 277 256 347 170 231
1-8 307 416 383 520 256 346
1-1/8 - 7 435 589 543 737 362 491
1-1/4 - 7 613 832 767 1040 511 693
1-3/8 - 6 804 1090 1005 1363 670 908
1-1/2 - 6 1067 1447 1334 1809 889 1206
M6 x 1.00 3.7 5.0 4.9 6.6 3.1 4.2
M8 x 1.25 9 12 12 16 7 10
M10 x 1.50 18 24 24 32 15 20
M12 x 1.75 31 42 41 56 26 35
M16 x 2.00 77 104 102 139 64 87
M20 x 2.50 150 203 200 271 125 169
M24 x 3.00 276 374 345 468 216 292

June 2010
MR AGITATOR APPENDIX
Table 14. Bolt grades and mechanical properties
(Source: www.boltdepot.com)

June 2010
P.O. Box 1123
Dayton, Ohio 45401
Phone: (937) 454-3200
Fax: (937) 454-3379
http://www.chemineer.com

Agitator Manual Chemineer PDF

Uploaded by

Copyright:

Available Formats

Agitator Manual Chemineer PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Agitator Manual Chemineer PDF

Uploaded by

Copyright:

Available Formats

What is the purpose of the manual?

What is the purpose of the manual?

What safety precautions are outlined in the manual?

What safety precautions are outlined in the manual?

Manual No. 812.

Installation, Operation and Maintenance Manual

For service and information contact:

Chemineer, Inc. Chemineer

E-mail: [email protected] E-mail: [email protected]

Web: www.chemineer.com Web: www.chemineer.com

B. INITIAL INSPECTION ......................................................................................... 2

C. CHEMINEER ASSISTANCE ............................................................................... 3

H. SEAL INSTALLATION - AUXILIARY STUFFING BOX ............................. 21

J. TAPER BORE COUPLING AND GEAR DRIVE INSTALLATION ............ 29

M. HANDHOLE COVER INSTALLATION .......................................................... 36

IOM Manual, Chemineer Page i

Page ii IOM Manual, Chemineer

IOM Manual, Chemineer Page iii

TABLE 1. DISPOSAL OF GEARBOX COMPONENTS....................................................... 7

Page iv IOM Manual, Chemineer

NC NOTE: The case size referred to in this

IOM Manual, Chemineer, Inc. Page 1

Page 2 IOM Manual, Chemineer

Phone: +1 (937) 454 3200 Phone: +44 (0) 1332 363175

For your convenience, Chemineer offers the following services:

- Installation and maintenance training seminars

- Installation and start-up supervision

- Preventative maintenance planning

- Parts order service

IOM Manual, Chemineer, Inc. Page 3

D.1 SAFETY SYMBOLS

Risk of fatalities and injury

Machine may be damaged

All work including transportation, storage, installation, electrical connection, commissioning,

Page 4 IOM Manual, Chemineer

IOM Manual, Chemineer, Inc. Page 5

D.5 SAFETY CHECKLIST

WHEN IN DOUBT, ASK!

Page 6 IOM Manual, Chemineer

Table 1. DISPOSAL OF GEARBOX COMPONENTS

Gear unit components: Material:

Gear unit housing, housing components, … Grey cast iron

Radial seals, sealing caps, rubber components,… Elastomers with steel

IOM Manual, Chemineer, Inc. Page 7

E.2 OUTDOOR OR LONG-TERM INDOOR STORAGE

Page 8 IOM Manual, Chemineer

Measures before commissioning the gearbox

E.2.1 To prevent from corrosion:

IOM Manual, Chemineer, Inc. Page 9

E.2.2 To protect elastomers:

E.3 CUSTOMER RESPONSIBILITY

Page 10 IOM Manual, Chemineer

1. The agitator extension shaft is designed to run in a true vertical position.

IOM Manual, Chemineer, Inc. Page 11

F.2 STRUCTURAL SUPPORT STEEL DESIGN GUIDELINES

THIS INFORMATION IS INTENDED AS A GUIDE, AND DOES NOT RELIEVE

Page 12 IOM Manual, Chemineer

Figure 1. Main Beam / Gusset Orientation

Figure 2. Angular Deflection Diagram