Axial Piston Compact Unit A10CO

Industrial
Hydraulics
Electric Drives
and Controls
Linear Motion and

Assembly Technologies
Pneumatics
Service
Automation
Mobile
Hydraulics
Axial Piston Compact Unit A10CO
RE 92 730/01.98
1/8
open circuit
Size 45
Series 52
Nominal Pressure 250 bar
Peak Pressure 315 bar
Contents
Features
Ordering code
Hydraulic fluid
Technical data
Characteristic curves for pump with pressure controller DR 5

Unit dimensions size 45, clockwise direction of rotation
Unit dimensions size 45, anti-clockwise direction of rotation 7

Circuit diagram
The A10VO compact unit was designed specifically for mobile

applications where it is necessary to boost the A10-inlet with a
full flow boost pump, i.e. hydraulic systems for agricultural
tractors, running on oil from the transmission (common oil
systems). This enables also an effective filtration in the A10inlet line.
A boost pump with a some what larger displacement can
provide extra oil for lubricating purposes.
Central hydraulic unit for mounting to transmission p.t.o.
in mobile applications
Integrated boost pump
A10VO main pump with controller
Filter mounting capability
Integrated pressure relief valves
Reduced pipework
Compact design
Transmission lubrication port
Measurement or monitoring ports
Integrated case drain port inside pilot diameter
2/8
Bosch Rexroth AG | Mobile Hydraulics
A10CO | RE 92 730/01.98
Ordering code
A10C
O 45
/ 52
Hydraulic fluid
Mineral oil (without prefix)
Axial-piston pump
Compact unit in swashplate design, adjustable
Nominal pressure 250 bar, peak pressure 315 bar
A10C
Operating mode
O
Pump, open-circuit
Size
Displacement volume Vg max (cm3)
45
Control options
Pressure controller
DR
Pressure controller, remote controlled
DRG
DRG
Pressure and flow controller
DFR
DFR
DFR
DR
DFR1
see RE 92703
without connection from X to tank

Series
52
Direction of rotation
R
cw
anti-cw
Viewing drive shaft
Seals
V
FPM (fluororubber to DIN ISO 1629)

Shaft end
Spline shaft SAE, shortened
Spline shaft SAE, shortened (higher through-drive torque)

Spline shaft SAE, shortened
1"
1"
7/8"
Mounting flange
C
SAE 2-hole
Port for service lines
Pressure port B
Suction port S
Pressure port B
Suction port S
metric thread side ports
07
SAE on opposite sides, metric fixing thread
12
Boost pump
with integrated boost pump
H00
Valves
with integrated pressure relief valves
Filtration
Filter installed in boost circuit
without filter, mounting option only
F
D
= available
= in preparation
H00 2
RE 92 730/01.98 | A10CO
Mobile Hydraulics | Bosch Rexroth AG
3/8
Hydraulic fluid
Comment on selecting hydraulic fluid
To select the correct hydraulic fluid it is necessary to know the
operating temperature in the tank (open circuit) in relation to
ambient temperature.
The hydraulic fluid must be selected in such a way that service
viscosity lies within the optimum range (opt) for the operating
temperature span, see shaded area in the chart.
We recommend selecting the next higher viscosity class in each
case.
Example: An ambient temperature of X C will produce an
operating temperature in the tank of 60 C. Given the optimum
service viscosity range (opt; shaded area), this will require
viscosity classes VG 46 or VG 68; class to select: VG 68.
Note: The leakage oil temperature, affected by pressure and
speed, is always higher than tank temperature. However,
temperature must not exceed 90 C anywhere in the system.
Please contact us if it is not possible to meet the above conditions
due to extreme service parameters or high ambient temperature.
Please refer to our catalogue sheets RE 90220 (mineral oil) and

RE 90221 (environmentally friendly hydraulic fluids) for detailed
information on selecting hydraulic fluids and on service conditions
before the project planning stage.
Operation with environmentally friendly hydraulic fluids may
result in modifications to the technical specifications; please
consult us if necessary.
Service viscosity range
We recommend selecting the service viscosity (at operating
temperature) in the range of
opt = opt. opt. service viscosity 16...36 mm2/s
for optimum efficiency and useful life, in relation to tank
temperature (open circuit).
Limiting viscosity range
Service limits are set at the following values:
min = 10 mm2/s
briefly at max. permissible leakage oil temperature of
90 C.
max = 1000 mm2/s
briefly on cold start.
Temperature range (see selection chart)
tmin = 25 C
tmax = +90 C
Selection diagram
- 20
20
60
40
80
1000
600
400
100
80
60
40
36
opt
Viscosity (mm2 / s)
00
68
46
32
22
1
VG
VG
VG
VG
VG
200
100
1000
20
15
10
- 25
16
- 10
t min = 25 C
10
30
50
Hydraulic fluid range
Hydraulic fluid filtering at the axial piston pump

To ensure operational reliability, the service fluid must conform
to at least purity class
9 to NAS 1638
18/15 to ISO/DIS 4406.
70
90
10
temperature
t ( C)
t max = + 90 C
4/8
A10CO | RE 92 730/01.98
Technical data
Service pressure range, input
Absolute pressure at port S
pabs min __________________________________________________________________ 0.8 bar
pabs max ____________________________________________________________________ 5 bar
Service pressure range, output
Pressure at port B
Nominal pressure pN _____________________________________________ 250 bar
Peak pressure pmax _______________________________________________ 315 bar
(pressures to DIN 24312)
Leakage fluid pressure

Maximum permissible leakage fluid pressure (at port L, L1):
pL max ____________________________________________________________ 2 bar absolut
Always given with end-face leakage oil bore allowing
unrestricted drainage into transmission housing.
Pressure at lubrication oil port G:
pabs min = 1bar
Direction of flow
S to B.
Table of values (theoretical values, ignoring mh and v; values rounded)

Size
45
Displacement volume
Vg max
cm3
45
Max. speed *
at Vg max
no max
rpm
2750
Max. volumetric flow (delivery)
at no max
qVo max
L/min
123
Max. power (p = 250 bar)
at no max
Po max
kW
52
Max. torque (p = 250 bar)
at Vg max
Tmax
Nm
181
kgm2
Moment of inertia around drive axle

Fluid capacity
0.0047
0.6
Mass (without fluid)
kg
27.2
Permissible load on drive shaft:

max. permissible axial force
Fax max
1500
max. permissible lateral force
Fq max
1500
*intermittently 3000 rpm
Application of forces
Fq
Fax
X/2 X/2
X
Calculating size
Volumetric flow
qV =
Drive torque
T =
Drive power
P =
Vg n v
[L/min]
1000
1.59 Vg p
[Nm]
100 mh
2 T n
60000
Tn
9549
qV p
600 t
[kW]
Vg
p
n
v
mh
t
= geometric displacement volume [cm3]

per revolution
= pressure differential [bar]
= speed [rpm]
= volumetric efficiency
= mechanical-hydraulic efficiency
= total efficiency (t = v mh)
RE 92 730/01.98 | A10CO
Characteristic curves for pump with

pressure controller DR
Drive power and delivery rate (volumetric flow)
(service fluid: hydraulic oil ISO VG 46 DIN 51519, t = 50 C)
Size 45
n = 1500 rpm
n = 2600 rpm
120
Volume rate of flow qV [L/min]
100
50
qV
80
PqV max
60
40
30
40
20
PqV
20
10
0
50
100
150
200
Service pressure p [bar]
250
Drive power P[kW]
60
5/8
6/8
A10CO | RE 92 730/01.98
Before finalising your design, please request certified assembly drawing.
Subject to alteration without notice.
Unit dimensions size 45, clockwise direction of rotation

Type A10CO 45
DR
DFR
DFR1 /52 R -V U C 07 H00 2 D
DRG
12
F
102
127,5
31
L1
80
21,5
15,1
87
90
101
7/8"
G
M2
G
21
9,5
1 3/8" UNF
57
S
M1
A/C
10
41
10
32
70,5
102,5
185
244
235
Shaft 22-4 (SAE B) shortened

SAE J744 OCT 83
30 mesh angle,
13 teeth,
16/32 pitch
Filter supplied with unit

for type F
175
94
B
View W
109
SW 19
50 Nm
SW 19
10 Nm
SW 6
View V
Pressure port B
52,4 +0,2
- 0,2
M10
26,2 +0,2
- 0,2
Model 12
S
25
Ports see page 7
RE 92 730/01.98 | A10CO
7/8
Before finalising your design, please request certified assembly drawing.

Subject to alteration without notice.
Unit dimensions size 45, anti-clockwise direction of rotation

Type A10CO 45
DR
DFR
DFR1 /52 L -V U C 07 H00 2 D
DRG
12
F
Shaft 22-4 (SAE B) shortened

SAE J744 OCT 83
30 mesh angle,
13 teeth,
16/32 pitch
244
141,5
109
102,5
31
L1
21,5
15,1
101,5
7/8"
G
M2
21
9,5
M1
S
A/C
1 3/8" UNF
57

for type F
dimensions see page 6
99,2
185
View W
175
94
SW19
10Nm
80
SW19
50Nm
SW 6
157
164
S
70,5
View V
Model 07
M33x2
M48x2
1 3/8" UNF-2B
Model 12
SAE 1" (standard pressure)
M48x2
1 3/8" UNF-2B
M12x1,5 integrated M12x1,5 integrated

7/8-14UNF-2B
7/8-14UNF-2B
X
Control pressure port
M14x1,5
with pressure controller DR X port closed
G
Transmission lubrication port M18x1,5
M10x1
M1, M2 Measurement ports
M14x1,5
M18x1,5
M10x1
25
Ports
B
Pressure port
S
Suction port
A/C Filter port, feed pump
to DIN 71457-A1,2
L
Case drain port
Case drain port
L1
M10
Pressure port B Model 12
102
26,2 +0,2
- 0,2
52,4 +0,2
- 0,2
10
8/8
A10CO | RE 92 730/01.98
Circuit diagram
Type A10CO 45 DFR /52 X- V U C XX H00 2D
F
X
LS
1 bar

for type F
A
must be set 10% higher
than DR-control
C
M2
S
not supplied with unit
100 m
L, L1
M1
p = max 0.2 bar at 130 L/min
Ports
B
S
A/C
L, L1
Pressure port
Suction port
Filter port, feed pump
Case drain ports
X
Control pressure port
with pressure controller DR X port closed
G
Transmission lubrication port
M1, M2 Measurement ports
Bosch Rexroth AG
Mobile Hydraulics
Product Segment Axial Piston Units
Horb Plant
An den Kelterwiesen 14
72160 Horb, Germany
Telephone +49 (0) 74 51 92-0
Facsimile +49 (0) 74 51 82 21
[email protected]
www.boschrexroth.com/brm
2003 by Bosch Rexroth AG, Mobile Hydraulics, 72160 Horb

All rights reserved. No part of this document may be reproduced or stored,
processed, duplicated or circulated using electronic systems, in any form or by
any means, without the prior written authorization of Bosch Rexroth AG. In the
event of contravention of the above provisions, the contravening party is obliged
to pay compensation.
The data specified above only serve to describe the product. No statements
concerning a certain condition or suitability for a certain application can be
derived from our information. The given information does not release the user
from the obligation of own judgement and verification. It must be remembered
that our products are subject to a natural process of wear and aging.

Axial Piston Compact Unit A10CO

Uploaded by

Copyright:

Available Formats

Axial Piston Compact Unit A10CO

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Axial Piston Compact Unit A10CO

Uploaded by

Copyright:

Available Formats

What is the A10VO unit designed for?

What is the A10VO unit designed for?

What features does the A10CO unit have?

What features does the A10CO unit have?

Industrial

Linear Motion and

Axial Piston Compact Unit A10CO

Characteristic curves for pump with pressure controller DR 5

Unit dimensions size 45, anti-clockwise direction of rotation 7

The A10VO compact unit was designed specifically for mobile

Bosch Rexroth AG | Mobile Hydraulics

Pressure controller, remote controlled

Pressure and flow controller

without connection from X to tank

Viewing drive shaft

FPM (fluororubber to DIN ISO 1629)

Spline shaft SAE, shortened (higher through-drive torque)

metric thread side ports

SAE on opposite sides, metric fixing thread

Mobile Hydraulics | Bosch Rexroth AG

Please refer to our catalogue sheets RE 90220 (mineral oil) and

Hydraulic fluid range

Hydraulic fluid filtering at the axial piston pump

Bosch Rexroth AG | Mobile Hydraulics

Leakage fluid pressure

Table of values (theoretical values, ignoring mh and v; values rounded)

Max. volumetric flow (delivery)

Max. power (p = 250 bar)

Max. torque (p = 250 bar)

Moment of inertia around drive axle

Mass (without fluid)

Permissible load on drive shaft:

max. permissible lateral force

*intermittently 3000 rpm

= geometric displacement volume [cm3]

Mobile Hydraulics | Bosch Rexroth AG

Characteristic curves for pump with

Volume rate of flow qV [L/min]

Service pressure p [bar]

Drive power P[kW]

Bosch Rexroth AG | Mobile Hydraulics

Unit dimensions size 45, clockwise direction of rotation

Shaft 22-4 (SAE B) shortened

Filter supplied with unit

Ports see page 7

Mobile Hydraulics | Bosch Rexroth AG

Before finalising your design, please request certified assembly drawing.

Unit dimensions size 45, anti-clockwise direction of rotation

Shaft 22-4 (SAE B) shortened

Filter supplied with unit

M12x1,5 integrated M12x1,5 integrated

Pressure port B Model 12

Bosch Rexroth AG | Mobile Hydraulics

Filter supplied with unit

p = max 0.2 bar at 130 L/min

2003 by Bosch Rexroth AG, Mobile Hydraulics, 72160 Horb

You might also like