IAI CT4 Cartesian Specsheet

Rotational Axis Equipped
CT4
High-speed Cartesian Robot
ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By:
High-speed Cartesian Robot That Shortens Assembly/Inspection
Cycle Times by Operating at High Speed, Ensuring High Rigidity
and Demonstrating Excellent Straight Moving Performance
High-speed operation with commanded acceleration of up to 3.2 G
(maximum instantaneous acceleration: 4.8 G)
CT4
Cartesian4AXIS
Function Comparison Table of High-speed Cartesian Robot
High-speed
Cartesian Robot CT4
Multi-jointed
robot
Parallel-link
robot
1. Speed, acceleration/deceleration
2. Rigidity
3. Robot size and operating range
4. Straight moving performance
Note) The evaluations under Multi-jointed robot and Parallel-link robot are based on IAIs evaluations of standard robots.
: Good / : Average / : Not very good
1
ELECTROMATE
www.electromate.com
[email protected]
Sold & Serviced By:
1I
2I
3I
4I
Rotational Axis Specifcation:
Newest Addition to the Series
High Speed & High Acceleration/Deceleration
Effcient Operation Range
High Rigidity, Easy to Install
You can now specify a CT4 robot having an ultra-compact
rotational axis installed at the end of the vertical axis. The
rotational axis lets you change the moving or aligning direction
of the work, thereby expanding the scope of applications of the
CT4 series further.
A wide operation range of 400 mm (X-axis) x 300 mm (Y-axis) is
ensured. Square operation ranges have no wasteful space and
are more effcient compared to those of multi-jointed robots and
parallel-link robots that can only operate in circles due to their
structure.
Boasting high frame rigidity, the CT4 has great acceleration capabilities and is subject to less vibration. While the parallel-link robot
is installed above the work part and thus normally requires a dedicated base, the CT4 can be installed easily on a plane at the same
height as the work part.
Examples of Applications
Packing electronic components in boxes Screwing automobile parts
Feeding/taking out work parts to/from
a part inspection machine
High-speed Cartesian robot
(rotational axis specifcation) + vision sensor
(standard specifcation) + vision sensor
(rotational axis specifcation)
2
Comparison of Standard Cycle Times
IAIs Cartesian robot
Acceleration/
deceleration: 1.2 G
1 cycle: 0.558 sec
1 cycle: 0.379 sec
32% shorter
IAIs CT4
High-speed
Cartesian robot
Acceleration/
deceleration: 3.2 G
Shorten the cycle time of your equipment by operating at the
maximum speed of 2500 mm/s and maximum acceleration of
3.2 G.
(Note) The standard cycle time represents the
time required for going back and forth along the
path shown to the right, consisting of a vertical
movement of 25 mm, horizontal movement of
200 mm and turning of 180 degrees.
The standard cycle time (Note) is 32% less than a
conventional Cartesian robot.
2
5
m
m
180
200mm
Standard cycle path
Range of
operation of
the Cartesian
robot CT4
Range of
operation of
the parallel-
link robot
Rotational
Axis
ELECTROMATE
www.electromate.com
[email protected]
Sold & Serviced By:
CT4 High-speed Cartesian Robot
CT4-G1RT-A-40-40-30-10B-36L-T2-
Orthogonal 4 Axes with Rotational
Axis Specifcation
Model
Specifcation
Items
CT4
G1RT A 40 40 30 10B T2 36L
Series Type Encoder type X1-axis stroke X2-axis stroke Y-axis stroke Z-axis stroke Applicable
controller
Range of
operation of R-axis
Cable length
CT4 : High-speed
Cartesian
Robot
G1RT: Gantry
4-axis
with
rotational
axis
A : Absolute
specifcation
40 : 400 mm 40 : 400 mm
Caution
30 : 300 mm 10B: 100 mm
With brake T2: XSEL-PCT
XSEL-QCT
36L: 360 deg
with limit
switch
L : Specifed
length
3L : 3 m
5L : 5 m
(Note 1)
(Note 2)
In the model number, the stroke is indicated in cm
(centimeters). The range of operation of the R-axis is
indicated in units of 10 degrees.
The cable length indicates the length from the
connection point on the actuators connector to the
controller.
The standard cable length is 3 m or 5 m, but any
other length can be specifed in units of meters.
Lengths up to 30 m are supported.
Specifcations
Structure
Model number
CT4-G1RT-A-40-40-30-10B-36L-T2-
X1 (master) axis X2 (slave) axis Y-axis Z-axis R-axis
Specifcations of
each axis
Axis type Slider Slider Slider Table Rotational axis
Stroke (mm) 400 400 300 100 360
Maximum speed (mm/sec) 2,500 2,500 2,500 833 4500/s
Combination
specifcations
Structure Orthogonal 4 axes (X-axis synchronized operation) + rotational axis
Degrees of freedom 4
Range of operation X-Y-Z (mm)-R (deg) 400-300-100-360
Positioning repeatability (mm) X direction : 0.02 (mm), Y direction : 0.02 (mm) , Z direction : 0.02 (mm), R direction : 0.025 (deg)
Lost motion (mm) X direction: 0.05 or less, Y direction: 0.05 or less, Z direction: -, R direction: -
Payload (kg) 0.5
Cycle time [arch motion] Measured value 200st : 0.379 sec, 300st : 0.468 sec
(Operating conditions)
Sigmoid control, 2,500 mm/sec, 3.2 G command (4.8 G max. instantaneously).
Refer to Fig. A below for the operation pattern.
Travel life (km) X/Y: 20,000, Z: 5,000 (90% probability of survival)
R-axis allowable load inertia (kgm
2
) 0.0002
R-axis allowable moment (Nm) 1.2
Installation orientation Limited to horizontal installation
Ambient temperature/humidity Temperature: 0 to 40C, Humidity: 85%RH max. (non-condensing)
Cycle Time Operation Pattern (Fig. A) Standard cycle path
Direction
of dynamic
allowable
moment
Dynamic Allowable Moment (R-axis)
Allowable moment of rotational axis 1.2 Nm
(Note) The standard cycle time represents the time required
for going back and forth along the path shown to the right,
consisting of a vertical movement of 25 mm, horizontal
movement of 200 mm and turning of 180 degrees.
Item X1 (master) axis X2 (slave) axis Y-axis Z-axis R-axis
Motor AC Servo motor (200 V)
Home detection Absolute
Drive method Ball screw + coupling
Integrated with motor
output shaft
Brake Not set Not set Not set Standard equipment Not set
C frame Aluminum casting
Robot weight 83.0 kg
3
X-axis 400 mm
Y-axis 300 mm
Z-axis 100 mm
R-axis 360
2
5
m
m
200mm
ELECTROMATE
www.electromate.com
[email protected]
Sold & Serviced By:
Dimensions
You can download CAD drawings
from our website.
Applicable Controller
[Rough Guide for Work Part Permitted on Rotational Axis]
Use the load inertia calculation formula below to check if the load inertia of the work part is equal to or less
than the allowable value (0.0002 kgm
2
).
<Example of Permitted Work Part>
If the work part weighs 0.1 kg and is 50 mm wide and 140
mm long, the load inertia is calculated as follows:
1/12 x 0.1 x (0.14
2
+ 0.05
2
) 0.00018 kgm
2
Accordingly, this work part is permitted on the rotational axis.
Be careful not to let the center of gravity of the
work part at the tip of the rotational axis be offset
from the output shaft of the rotational axis.
Center
of rotation
Center
of rotation
Mass: M Mass: M Weight 0.1 kg
Applicable controller
Maximum number of
controlled axes
Compatible encoder
type
Number of
programs
Number of
positions
Power-supply
voltage
Description
XSEL-PCT
6 axes Absolute
128
programs
20,000
positions
3-phase,
200VAC
Dedicated standard controller for CT4
XSEL-QCT
Dedicated global controller for CT4
(Safety Category compliant)
4
Mounting hole dimensions
Section E-E
Mounting holes (12 locations) and eye-bolt
installation positions (3 locations)
Reference
mounting surface
3-M10
23, counterbored, depth 5
(for eye-bolt)
Reference
mounting surface
Bulkhead plug (4 x 2)
for air pipe connection
Motor cable inlet
Encoder cable inlet
Reference
mounting
surface
Reference mounting surface
Air piping:
2 4 pipes are installed
along the Z-axis.
Detail Diagram B
7 (width across fats)
Detail Diagram H
3-M6, depth 10
View of C
Angle of width
across fats upon
completion of
home return
ELECTROMATE
www.electromate.com
[email protected]
Sold & Serviced By:
CT4-G1-A-40-40-30-10B-T2-
4-axis Cartesian Specifcation
Model
Specifcation
Items
CT4
G1 A 40 40 30 10B T2
Series Type Encoder X1-axis stroke X2-axis stroke Y-axis stroke Z-axis stroke Applicable
controller
Cable length Option
CT4 : High-speed
Cartesian
Robot
G1 : Gantry
4-axis
type
A : Absolute
specifcation
40 : 400 mm 40 : 400 mm
Note
30 : 300 mm 10B : 100 mm
With brake T2 : XSEL-PCT
XSEL-QCT L : Length
designation
3L : 3 m
5L : 5 m
Blank: No option
AC: Air pipe
connection
(Vacuum port)
(Note 1)
(Note 2)
Strokes are indicated in cm (centimeters) in the
model names.
The cable length is from the connection point on
the robot connector to the controller.
The standard length is 3 m or 5 m, but other
lengths can be specifed in m.
Lengths up to 30 m are supported.
Specifcations
Structure
Type
CT4-G1-A-40-40-30-10B-T2-
X1 (master) axis X2 (slave) axis Y-axis Z-axis
Specifcations of
each axis
Axis type Slider Slider Slider Table
Stroke (mm) 400 400 300 100
Maximum speed (mm/sec) 2,500 2,500 2,500 833
Combination
specifcations
Structure Orthogonal 4-axis (X-axis synchronizing operation)
Degrees of freedom 3
Operating range X-Y-Z (mm) 400-300-100
Positioning repeatability (mm) X direction : 0.02, Y direction : 0.02, Z direction : 0.02
Lost motion (mm) X direction : 0.05 or less, Y direction: 0.05 or less, Z direction : -
Payload (kg) 1
Cycle time [arch motion] Measured value 200st : 0.379 sec, 300st : 0.468 sec
(Operating conditions)
Sigmoid control, 2,500 mm/sec, commanded acceleration up to 3.2 G
(maximum instantaneous acceleration: 4.8 G)
Travel life (km) X/Y : 20,000, Z : 5,000 (90% survival probability)
Dynamic allowable moment (Note 1) (N
.
m) Ma = 6.4, Mb = 9.2, Mc = 14.2 (based on travel life of 5,000 km)
Overhang load length (Note 1) (mm) X direction : 50, Y direction : 50, Z direction : 50
Installation orientation Limited to horizontal installation
Ambient temperature/humidity Temperature: 0 to 40C, humidity : 85% RH or less (non-condensing)
(Note 1) Measured at the mounting point at the end of the Z-axis.
Dynamic allowable moment (Z-axis)
Item X1 (master) axis X2 (slave) axis Y-axis Z-axis
Motor AC servo motor (200V)
Home detection Absolute
Drive system Ball screw + coupling
Brake Not set Not set Not set Standard equipment
C type frame Aluminum casting
Robot weight 82.0 kg
5
X-axis 400 mm
Y-axis 300 mm
Z-axis 100 mm
ELECTROMATE
www.electromate.com
[email protected]
Sold & Serviced By:
Dimensions
You can download CAD drawings
from our website.
Mounting hole dimension
Section E-E
Mounting
reference
surface
Mounting
reference
surface
Mounting reference
surface
3-M10
23 counterbored,
depth 5 (for eye bolt)
Detail B
3-M6, depth 10
Drawing view C
6-M5, depth 6
5 H7, depth 5
5 H7, depth 5
Mounting holes (12 locations) and eye-
bolt mounting positions (3 locations)
[Calculation of Dynamic Allowable Moment]
With the CT4, the dynamic allowable moment is calculated based on a travel life of 20,000 km for the X-axis/Y-axis and travel life of
5,000 km for the Z-axis (both at a survival probability of 90%).
6
Motor cable inlet
Encoder cable inlet
Mounting
reference
surface
Without air pipe connection port: 805
With air pipe connection port: 820
Applicable Controller
Maximum number of
controlled axes
Compatible encoder
type
Number of
programs
Number of
positions
Power-supply
voltage
Description
XSEL-PCT
6 axes Absolute
128
programs
20,000
positions
3-phase,
200VAC
Dedicated standard controller for CT4
XSEL-QCT
Dedicated global controller for CT4
(Safety Category compliant)
Motor cable inlet
Encoder cable inlet
ELECTROMATE
www.electromate.com
[email protected]
Sold & Serviced By:
System confguration
Regenerative Resistance Unit
External
equipment
PLC, etc.
Supplied with the robot
Various Field Net-
work Connections
Option
Option
Option
Serial
Communication Port
Standard 2ch for RS232
Teaching Pendant
Model: SEL-T
SEL-TD
I/O Flat Cable 2 m
Control Power
Supply
Single-phase
AC200V
Motor Drive
Power Supply
3-phase
AC200V
System I/O Expansion I/O
Emergency stop
Enable
System ready
* Required only for global type (Not required for the standard type)
I/O board
Multi-point board
RS232 connection version
Model: IA-101-X-MW
USB connection version
Model: IA-101-X-USBMW
PC Software
Encoder Cable
Model CB-CT4-PA
Standard: 3 m/5 m
Actuator
RCS2 series (*)/RCS3 series/single-axis robot
(Note) The total wattage of Axes 5 and 6 cannot
be more than 100 W.
(*) Excluding the RCS2-RA7/SRA7 series
Regenerative unit cable 1 m
Regenerative resistor unit
* 2 regenerative resistor
units are required.
Drive Power Shut-off Circuit
(Supplied by user)
Main Power Supply 3-phase AC200V
* When connecting the power, be sure to attach the flter listed below or equivalent:
Noise Filter Recommended Model: 3-phase MC1320 (Manufacturer: TDK Lambda)
Ring Core Recommended Model: ESD-R-25 (Manufacturer: NEC TOKIN)
Clamp Filter Recommended Models: ZCAT3035 -1330 for control power (Manufacturer: TDK)
RFC-H13 for motor power (Manufacturer: Kitagawa Kogyo Co., Ltd.)
Surge Protector Recommended Models: 3-phase R/A/V-781BXZ-4
(Manufacturer: Okaya Electric Industries)
Motor Cable
Model CB-CT4-MA
Standard: 3 m/5 m
Model
Specifcations
* Order two regenerative resistor units
together with the robot.
This unit converts to heat the regenerative current produced when the motor decelerates.
Two regenerative units are needed to operate the CT4.
Item Specifcations
Main Unit dimensions W34mm x H195mm x D126mm
Main Unit Weight 0.9kg
Built-in regenerative resistor 220 80W
Accessory Controller Connection Cable (Model No. CB-ST-REU010) 1m
7
Orthogonal 4 axes + rotational axis type
Motor Cable
Model:CB-CT4R-MA
Standard: 3 m/5 m
Encoder Cable
Model:CB-CT4R-PA
Standard: 3 m/5 m
4-axis Cartesian type
Supplied with
the controller
Supplied with the regenerative resistor unit
Option
ELECTROMATE
www.electromate.com
[email protected]
Sold & Serviced By:
Axis Reactive force
X-axis 660N
Y-axis 235N
Z-axis 85N
X-SEL Controller
Part Names
Notes
Y-Z cable
X-Y cable
Connector box
X reference surface
Connector
connection point
Motor cable inlet
Encoder cable inlet
Detail of connector
connection point
X master axis
Z-axis
X slave axis
Frame
Y reference
surface
Y-axis
The mounting surface shall be a machined plane or fat plane of equivalent accuracy. The fatness shall be within 0.05 mm/m.
The frame shall have a structure that allows the robot to be installed horizontally.
The frame on which the robot is installed receives a large reactive force. The table below shows the maximum instantaneous reactive force (rough guide) received
by each axis when the axis moves at the maximum speed and maximum acceleration carrying 1 kg of load.
Provide a frame of suffcient rigidity. Secure the frame to the foor, etc., using anchor bolts, etc., so that the CT4 will not move as a result of robot operation.
An example of the installation frame is shown to the right. Fabricate the
installation frame by referring to this example.
Use the hexagonal head bolt, as described below, for the mounting bolt,
depending on the installation frame material.
Use high-strength bolts of ISO-10.9 or more.
When operating the high-speed Cartesian robot, the acceleration/deceleration setting for sigmoid motion, and vibration
control, must be set in the program. For details, refer to the operation manual.
<Frame Made of Steel>
Applicable bolt: M10 x 40 (effective engagement length: 10 or more), Applicable washer: M10 (10.5 x 18 x 2)
Tightening torque: 60 N
.
m
<Frame Made of Aluminum>
Applicable bolt: M10 x 50 (effective engagement length: 20 or more), Applicable washer: M10 (10.5 x 18 x 2)
Tightening torque: 60 N
.
m
The natural vibration frequency of the frame shall be 75 Hz or more.
Installation Frame
Example of the Installation Frame
Operation Setting
100 x 100mm x t6.0mm
(square steel material)
900mm 500mm
25mm or more
0.05/1000
800mm or less
Danger
Use the specifed type of bolt. Pay attention when selecting the bolt length. If bolts other than the
specifed type or of inappropriate lengths are used, the tapped holes may be damaged or suffcient
mounting strength may not be achieved, potentially leading to noise/vibration, breakdown or shorter life.
In the worst case, the CT4 may move suddenly and cause serious accidents such as damage to the work
part and surrounding areas, injury or even death.
8
<Orthogonal 4 axes + rotational axis type>
<4-axis Cartesian type>
X-Y cable (with built-in air pipe)
Air pipe [1] connection port
Air pipe [2] connection port
R-axis
Y-Z cable
(with built-in air pipe)
Encoder cable inlet
Motor cable inlet
Specifcation with air pipes No air pipe specifcation
<Air Pipe>
The orthogonal 4 axes + rotational axis type comes standard with an air pipe to
the end of the Z-axis.
The orthogonal 4 axes type does not come standard with built-in air pipes, so
specify the optional specifcation with air pipes (option code: AC) if necessary.
ELECTROMATE
www.electromate.com
[email protected]
Sold & Serviced By:
Series
Type Number of
connected
axes
Axis 1
* Same as the 5-axis specifcation if
only the CT4 is operating.
Axis 2 Axis 3
60AB 60AL 3
Axis 4 Axis 5 Axis 6 Network Standard I/O Expansion I/O I/O Cable
Length
Power supply
voltage
PCT Dedicated CT4 type
QCT
Dedicated CT4
global type
(Safety Category
compliant)
5 5-axis specifcation
12I 12-watt motor (incremental)
12A 12-watt motor (absolute)
20I 20-watt motor (incremental)
20A 20-watt motor (absolute)
30DI RCS 30-watt motor (incremental)
30DA RCS 30-watt motor (absolute)
30RI RS 30-watt motor (incremental)
30RA RS 30-watt motor (absolute)
E Not used
N1 Input 32/Output 16 (NPN)
P1 Input 32/Output 16 (PNP)
S With expansion I/O base
0 No cable
2 2m (standard)
3 3m
5 5m
3 Three-phase 200 VAC
Blank Not used
DV DeviceNet connection board
CC CC-Link connection board
PR ProfBus connection board
ET Ethernet connection board
400A
400-watt
motor, absolute
400A
400-watt motor,
absolute
60AB
60-watt motor,
absolute, with brake
60AL
60-watt motor,
absolute, with limit
switch
400A
400-watt motor,
absolute
The maximum wattage of axis 6 is 30 W.
(If the wattage is more than the above, the
axis cannot operate due to the limitations
of the power-supply capacity.)
* If expansion I/O will not be used,
enter E (Not used) for slots 2 to 4.
If you are using expansion I/Os, enter
the expansion I/O base specifcation
code in the desired slot.
If an expansion I/O is specifed, the
controller chassis will come with the
expansion I/O base.
If you will not be using the expansion
I/O initially but will be adding it later,
specify the chassis with I/O expansion
board, but specify S for slots 2 to 4.
* If E (not used) or S
(with expansion
I/O base) is specifed for all
of standard and expansion
I/Os slots, the I/O cable
length will become 0
(no cable).
XSEL-PCT/QCT Controller
XSEL-PCT/QCT
Dedicated program controller for
CT4 high-speed Cartesian robot
<Orthogonal 4 axes + rotational axis type>
9
Series
Type Number of
connected
axes
Axis 1 Axis 2 Axis 3 Axis 4 Axis 5 Axis 6 Network Standard I/O Expansion I/O I/O Cable
Length
Power supply
voltage
PCT Dedicated CT4 type
QCT
Dedicated CT4
global type
(safety category-
compliant
specifcation)
12I 12W motor (Incremental)
12A 12W motor (Absolute)
30DI 30W motor for RCS (Incremental)
30DA 30W motor for RCS (Absolute)
30RI 30W motor for RS (Incremental)
30RA 30W motor for RS (Absolute)
E Not used
S With expansion I/O base
0 No cable
2 2m (standard)
3 3m
5 5m
3 Three-phase AC200V
Blank Not used
DV DeviceNet board
CC CC-Link board
PR Profbus board
ET Ethernet board
400A
400-watt
motor, absolute
400A
400-watt
motor, absolute
60AB
60W motor, absolute,
with brake
400A
400-watt
motor, absolute
The total wattage of Axes 5 and 6 must not
be more than 100 W. (Take note that if the
above wattage is exceeded, the robot will
not operate due to power-supply capacity
limitations.)
* If expansion I/O will not be used,
enter E (not used) for slots 2 to 4.
If you are using expansion I/O, enter
the expansion I/O code in the desired
slot. If an expansion I/O is specifed,
the controller chassis will come with
the expansion I/O base.
If you will not be using the expansion
I/O initially but will be adding it later,
specify the chassis with I/O expansion
board, but specify S for slots 2 to 4.
* If E (not used) or S
(with expansion
I/O base) is specifed for all
of standard and expansion
I/O slots, the I/O cable length
will become 0 (no cable).
60AB 3
<4-axis Cartesian type>
ELECTROMATE
www.electromate.com
[email protected]
Sold & Serviced By:
Specifcations
Model Description
Controller Series, Type PCT (standard) type QCT (global) type
Connecting robots/actuators CT4, RCS2, RCS3, single-axis robot
Connectable motor output CT4 + 100 W max.
Number of Controlled Axes 4-axis 5-axis 6-axis 4-axis 5-axis 6-axis
Control power-supply input 200/230 AC, single-phase -15%, +10%
Motor power-supply input 200/230 AC, three-phase -10%, +10%
Power Supply Frequency 50/60Hz
Insulation resistance 10 M or more (between power-supply terminal and I/O terminal, or between all external terminals and case, at DC500V)
Withstand voltage AC1500V (1 minute)
Power Supply Capacity (*1)
Max
4019VA
Max
4265VA
Max
4271VA
Max
4019VA
Max
4265VA
Max
4271VA
Position detection method
Incremental Encoder (serial encoder)
Absolute encoder with a rotational data backup (serial encoder)
Safety Circuit Confguration Redundancy not supported Redundancy supported
Drive Source Breaker System Cutoff by internal relay External safety circuit
Enable Input Contact B input (internally powered) Contact B input (externally powered, redundant)
Speed setting 1 mm/sec or greater. The upper limit varies according to the actuator specifcation.
Acceleration/Deceleration Setting 0.01 G or greater. The upper limit varies according to the actuator.
Program language Super SEL language
Number of programs 128 Programs
Number of program steps 9,999 Steps (total)
Number of multi-tasking programs 16 Programs
Number of Positions 20,000 Steps (total)
Data memory device Flash ROM + SRAM Battery Backup
Data input method Teaching pendant or PC software
Standard Input/Output 48-I/O PIO board (NPN/PNP) or 96-I/O PIO board (NPN/PNP). Only 1 board can be installed.
Expansion Input/Output 48-I/O PIO board (NPN/PNP) and/or 96-I/O PIO board (NPN/PNP). Up to 3 boards can be installed.
Serial communication function Teaching pendant port (D-sub 25-pin) + 2-channel RS232C port (D-sub, 9-pin x 2). Standard equipment.
Protective function Motor overcurrent, Overload, Motor driver temperature check, Overload check, Encoder open-circuit check, soft limit over, system error, battery error
Ambient Operating Temperature /
Humidity and Atmosphere
0 to 40C, 10 to 95% (non-condensing). Free from corrosive gases. In particular, there shall be no signifcant dust.
Robot weight (*2) 5.2kg 5.7kg 4.5kg 5kg
Accessory I/O Flat Cable
*1 When the connected axes represent the maximum wattage.
*2 Including the absolute-data backup battery, brake mechanism and expansion I/O box.
10
ELECTROMATE
www.electromate.com
[email protected]
Sold & Serviced By:
I/O Signal table
External Dimensions
Standard I/O Signal Table (when N1 or P1 is selected) Extension I/O Signal Table (when N1 or P1 is selected) Extension I/O Signal Table (when N2 or P2 is selected)
Pin No. Classifcation Port No. Standard Settings
1
Input
- (J/P/Q type: 24V connection / K type: NC)
2 000 Program start
3 001 General Purpose Input
9 007 Program Specifcation (PRG No.1)
34
Output
300 Alarm Output
35 301 Ready Output
36 302 Emergency Stop Output
37 303 General Purpose Output
50 - (J/P/Q type: 0V connection / K type: NC)
Pin No. Classifcation Standard Settings
1
Input
(J/P/Q type: 24V connection / K type: NC)
2 General Purpose Input
34
Output
General Purpose Output
35 General Purpose Output
50 (J/P/Q type: 0V connection / K type: NC)
Pin No. Classifcation Standard Settings
1
Input
(J/P/Q type: 24V connection / K type: NC)
18
Output
General Purpose Output
50 (J/P/Q type: 0V connection / K type: NC)
Standard specifcation With expansion I/O base Side View
Controller Type
Encoder Absolute Absolute
Common Brake Yes Yes
I/O Standard only Standard + Expansion
PCT
4 axis
Specifcation
5 to 6 axis
Specifcation
QCT
4 axis
Specifcation
5 to 6 axis
Specifcation
Battery Box
(Applies to ABS model)
11
ELECTROMATE
www.electromate.com
[email protected]
Sold & Serviced By:
Option
Teaching Pendant
PC software (Windows dedicated)
A teaching device that has program/position input,
test operation, monitoring function, etc.
Model
Confguration
Confguration
Confguration
Confguration
PC Software
(CD)
PC Software
(CD)
PC Software
(CD)
RS232C Cable
CB-ST-E1MW050-EB
RS232C Cable
CB-ST-E1MW050-EB
Safety category-compliant cable
CB-ST-A1MW050-EB
USB Cable
CB-SEL-USB030
USB Conversion Adapter
IA-CV-USB
XSEL-P/PX/PCT
XSEL-P/PX/PCT
XSEL-Q/QX/QCT
Specifcations
SEL-T Option
Features
Model IA-101-X-MW (with RS232C cable)
Model IA-101-XA-MW (with safety category 4-compliant cable)
Model IA-101-X-USBMW (with USB Conversion Adapter + Cable)
<XSEL-P/PX/PCT Type>
<XSEL-Q/QX/QCT Type>
A startup support software program offering program/position
input function, test operation function, monitoring function,
and more.
The functions needed for debugging have been enhanced to
help reduce the startup time.
Wall-mounting
hook Model HK-1
Strap
Model STR-1
Model Description
SEL-T Standard type
SEL-TD With deadman switch
Item SEL-T SEL-TD
3-position enable switch Not available Available
ANSI/UL standard Not supported Supported
CE mark Supported
Display 20 characters x 4 lines
Ambient operating temperature/humidity 0 to 40C 10 to 90% RH (non-condensing)
Protective structure IP54
Mass Approx. 0.4 kg (cable excluded)
Note
Use the IA-101-X-MW or IA-101-X-USBMW for the XSEL-P/PX/PCT.
Use the IA-101-XA-MW for the XSEL-Q/QX/QCT.
Note that connecting a PC software cable to a controller not supporting the
cable may damage the internal parts of the controller.
12
ELECTROMATE
www.electromate.com
[email protected]
Sold & Serviced By:
Service Parts
Motor Cable <Orthogonal 4 axes + rotational axis type>
Encoder Cable <Orthogonal 4 axes + rotational axis type>
Model: CB-CT4R-MA
Model: CB-CT4R-PA
[Minimum bending radius]
Flexible cable: 51 mm
Fixed cable: 34 mm
[Minimum bending radius]
Flexible cable: 44 mm
Fixed cable: 29 mm
Enter the cable length (L) into (Maximum 30m). Ex.: 080 = 8m
Pin no. Signal name Size
1 PE
AWG 18
2 U
3 V
4 W
10 NC
AWG26
(soldered)
11 NC
12 NC
13 NC
26 NC
25 NC
24 NC
23 NC
9 NC
18 NC
19 NC
1 NC
2 NC
3 NC
4 NC
5 NC
6 NC
7 SRD+
8 SRD-
14 BAY+
15 BAT-
16 Vcc
17 GND
20 BKR-
21 BKR+
Clamp the shield to the hood
10 NC
AWG26
(soldered)
11 NC
12 E24V
13 OV
26 LS
25 CREEP
24 OT
23 RSV
9 NC
18 NC
19 NC
1-6 NON
7 SRD+
8 SRD-
14 BAT+
15 BAT-
16 Vcc
17 GND
20
21
Clamp the shield to the hood
1 PE
AWG 18
2 U
3 V
4 W
1 PE
AWG 18
2 U
3 V
4 W
1 PE
AWG 18
2 U
3 V
4 W
1 PE
AWG 18
2 U
3 V
4 W
CN 2
CN 2
CN 6
CN 1
CN 1
CN 3
CN 4
CN 5
CN 6
A01 U
AWG 18
A02 V
B01 W
B02 PE
A03 U
A04 V
B03 W
B04 PE
A05 U
A06 V
B05 W
B06 PE
A07 U
A08 V
B07 W
B08 PE
A09 U
A10 V
B09 W
B10 PE
A01 BAT+
AWG 26
A02 BAT-
A03 SD
A04 -SD
A05
B01 Vcc
B02 GND
B03 FG
B04 BK-
B05 BK+
A06 BAT+
A07 BAT-
A08 SD
A09 -SD
A10
B06 Vcc
B07 GND
B08 FG
B09 BK-
B10 BK+
A11 BAT+
A12 BAT-
A13 SD
A14 -SD
A15
B11 Vcc
B12 GND
B13 FG
B14 BK-
B15 BK+
A16 BAT+
A17 BAT-
A18 SD
A19 -SD
A20
B16 Vcc
B17 GND
B18 FG
B19 BK-
B20 BK+
A21 BAT+
A22 BAT-
A23 SD
A24 -SD
A25 LS
B21 Vcc
B22 GND
B23 FG
B24 N
B25 24V
CN3: Same with CN2
CN4: Same with CN2
CN5: Same with CN2
13
ELECTROMATE
www.electromate.com
[email protected]
Sold & Serviced By:
Motor cable < 4-axis Cartesian type >
Encoder cable < 4-axis Cartesian type >
I/O fat cable (for XSEL-J/K/P/Q)
Model CB-CT4-MA
Model CB-CT4-PA
Model CB-X-PIO
Flat cable (50-core)
No
connector
[Minimum Bend Radius]
Movable: 51 mm
Fixed: 34 mm
[Minimum Bend Radius]
Movable: 44 mm
Fixed: 29 mm
Number Color Wire
1 Brown 1
Flat cable
crimped
2 Red 1
3 Orange 1
4 Yellow 1
5 Green 1
6 Blue 1
7 Purple 1
8 Gray 1
9 White 1
10 Black 1
11 Brown-2
12 Red 2
13 Orange 2
14 Yellow 2
15 Green 2
16 Blue 2
17 Purple 2
Number Color Wire
18 Gray 2
Flat cable
crimped
19 White 2
20 Black 2
21 Brown-3
22 Red 3
23 Orange 3
24 Yellow 3
25 Green 3
26 Blue 3
27 Purple 3
28 Gray 3
29 White 3
30 Black 3
31 Brown-4
32 Red 4
33 Orange 4
34 Yellow 4
Number Color Wire
35 Green 4
Flat cable
crimped
36 Blue 4
37 Purple 4
38 Gray 4
39 White 4
40 Black 4
41 Brown-5
42 Red 5
43 Orange 5
44 Yellow 5
45 Green 5
46 Blue 5
47 Purple 5
48 Gray 5
49 White 5
50 Black 5
10 NC
AWG18
(soldered)
11 NC
12 NC
13 NC
26 NC
25 NC
24 NC
23 NC
9 NC
18 NC
19 NC
1 NC
2 NC
3 NC
4 NC
5 NC
6 NC
7 SRD+
8 SRD-
14 BAY+
15 BAT-
16 Vcc
17 GND
20 BJR+
21 BKR-
The shield is connected to the hood by a clamp.
A01 BAT+
AWG 26
A02 BAT-
A03 SD
A04 -SD
A05
B01 Vcc
B02 GND
B03 FG
B04 BK-
B05 BK+
A06 BAT+
A07 BAT-
A08 SD
A09 -SD
A10
B06 Vcc
B07 GND
B08 FG
B09 BK-
B10 BK+
A11 BAT+
A12 BAT-
A13 SD
A14 -SD
A15
B11 Vcc
B12 GND
B13 FG
B14 BK-
B15 BK+
A16 BAT+
A17 BAT-
A18 SD
A19 -SD
A20
B16 Vcc
B17 GND
B18 FG
B19 BK-
B20 BK+
A21
A22
A23
A24
A25
B21
B22
B23
B24
B25
CN 2 CN 1
CN3: Same with CN2
CN4: Same with CN2
CN5: Same with CN2
1 PE
AWG 18
2 U
3 V
4 W
1 PE
AWG 18
2 U
3 V
4 W
1 PE
AWG 18
2 U
3 V
4 W
1 PE
AWG 18
2 U
3 V
4 W
CN 2 CN 1
CN 3
CN 4
CN 5
A01 U
AWG 18
A02 V
B01 W
B02 PE
A03 U
A04 V
B03 W
B04 PE
A05 U
A06 V
B05 W
B06 PE
A07 U
A08 V
B07 W
B08 PE
A09 NC
A10 NC
B09 NC
B10 NC
14
ELECTROMATE
www.electromate.com
[email protected]
Sold & Serviced By:

IAI CT4 Cartesian Specsheet

Uploaded by

Copyright:

Available Formats

IAI CT4 Cartesian Specsheet

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

IAI CT4 Cartesian Specsheet

Uploaded by

Copyright:

Available Formats

Rotational Axis Equipped

You might also like