Hyosung GV650

GV650(S/M)E-표지
2005.7.18
3:51
PM
페이지1
001
PagePro
9100
300DPI
100LPI
HYOSUNG MOTORS & MACHINERY INC.
SERVICE MANUAL
SERVICE MANUAL
99000-51210
FOREWORD GROUP INDEX
This manual contains an introductory description on

HYOSUNG and procedures for its
GENERAL INFORMATION 1
inspection/service and overhaul of its main components.
Other information considered as generally known is not
included.
PERIODIC MAINTENANCE 2
Read GENERAL INFORMATION section to familiarize
yourself with outline of the vehicle and MAINTENANCE
and other sections to use as a guide for proper inspec-
tion and service.
ENGINE 3
This manual will help you know the vehicle better so
that you can assure your customers of your optimum
and quick service.
FUEL SYSTEM 4
� This manual has been prepared on the basis of the COOLING SYSTEM 5
latest specification at the time of publication.
If modification has been made since then,
difference may exist between the content of this
manual and the actual vehicle.
ELECTRICAL SYSTEM 6
� I llustrations in this manual are used to show the
basic principles of operation and work procedures.
They may not represent the actual vehicle exactly CHASSIS 7
in detail.
WARNING
SERVICING INFORMATION 8
This manual is intended for those who have
enough knowledge and skills for servicing
HYOSUNG vehicles. Without such knowledge and
skills, you should not attempt servicing by relying
on this manual only.
Instead, please contact your nearby authorized
HYOSUNG motorcycle dealer.
� COPYRIGHT HYOSUNG MOTORS & MACHINERY INC. 2005.

HOW TO USE THIS MANUAL
TO LOCATE WHAT YOU ARE
LOOKING FOR:
1. The text of this manual is divided into sections.
2. As the title of these sections is listed on the previous
page as GROUP INDEX, select the section where you are look-
ing for.
3. Holding the manual as shown at the right will allow you to find
the first page of the section easily.
4. On the first page of each section, its contents are listed. Find
the item and page you need.
COMPONENT PARTS
Example : Front wheel

SYMBOL
Listed in the table below are the symbols indicating instructions and other information necessary for servicing and
meaning associated with them respectively.
SYMBOL DEFINITION SYMBOL DEFINITION
Torque control required.

Apply THREAD LOCK“1324”.
Data beside it indicates specified torque.
Apply oil. Use engine oil unless otherwise

Apply or use brake fluid.
specified.
Apply SUPER GREASE“A”. Measure in voltage range.
Apply SUPER GREASE“C”. Measure in resistance range.
Apply SILICONE GREASE. Measure in current range.
Apply MOLY PASTE. Use special tool.
Apply BOND“1215”. Use engine coolant.
Use fork oil.

NOTE
Difference between photographs and actual motorcycles depends on the markets.
GENERAL INFORMATION
1
CONTENTS
INFORMATION LABELS ………………………………………………… 1- 1

GENERAL PRECAUTIONS …………………………………………… 1- 1
SERIAL NUMBER LOCATION ………………………………………… 1- 3
FUEL, OIL AND ENGINE COOLANT RECOMMENDATIONS …… 1- 4
BREAK-IN PROCEDURES……………………………………………… 1- 6
CYLINDER CLASSIFICATION ………………………………………… 1- 6
EXTERIOR ILLUSTRATION …………………………………………… 1- 7
SPECIFICATIONS ………………………………………………………… 1- 8
1-1 GENERAL INFORMATION
WARNING / CAUTION / NOTE

Please read this manual and follow its instructions carefully. To emphasize special information, the symbol and
the words WARNING, CAUTION and NOTE have special meanings. Pay special attention to the messages
highlighted by these signal words.
WARNING
Indicates a potential hazard that could result in death or injury.
CAUTION
Indicates a potential hazard that could result in vehicle damage.
NOTE
Indicates special information to make maintenance easier or instructions cleaner.
Please note, however, that the warning and cautions contained in this manual cannot possibly cover all potential
hazards relating to the servicing, or lack of servicing, of the motorcycle. In addition to the WARNING and CAUTION
stated, you must use good judgement and basic mechanical safety principles. If you are unsure about how to perform a
particular service operation, ask a more experienced mechanic for advice.
GENERAL PRECAUTIONS
WARNING
� Proper service and repair procedures are important for the safety of the service machanic and the safe-
ty and reliability of the vehicle.
� When 2 or more persons work together, pay attention to the safety of each other.
� When it is necessary to run the engine indoors, make sure that exhaust gas is forced outdoors.
� When working with toxic or flammable materials, make sure that the area you work in is well-ventilat-
ed and that you follow all off the material manufacturer’s instructions.
� Never use gasoline as a cleaning solvent.
� To avoid getting burned, do not touch the engine, engine oil, exhaust system or radiator during or
for a while after engine operation.
� After servicing fuel, oil, engine coolant, exhaust or brake systems, check all lines and fittings related
to the system for leaks.
GENERAL INFORMATION 1-2
WARNING
� If parts replacement is necessary, replace the parts with HYOSUNG Genuine Parts or their equivalent.
� When removing parts that are to be reused, keep them arranged in an orderly manner so that they may
be reinstalled in the proper order and orientation.
� Be sure to use special tools when instructed.
� Make sure that all parts used in reassembly are clean, and also lubricated when specified.
� When use of a certain type of lubricant, bond, or sealant is specified, be sure to use the specified type.
� When removing the battery, disconnect the negative cable first and then positive cable. When
reconnecting the battery, connect the positive cable first and then negative cable, and replace the terminal
cover on the positive terminal.
� When performing service to electrical parts, if the service procedures do not require use of
battery power, diconnect the negative cable at the battery.
� Tighten cylinder head and case bolts and nuts, beginning with larger diameter and ending with small-
er diameter, from inside to outside diagonally, to the specified tightening torque.
� Whenever you remove oil seals, gaskets, packing, O-rings, locking washers, cotter pins, circlips,
and certain other parts as specified, be sure to replace them with new ones. Also, before installing
these new parts, be sure to remove any material left over from the mating surfaces.
� Never reuse a circlip. When installing a new circlip, take care not to expand the end gap larger
than required to slip the circlip over the shaft. After installing a circlip, always ensure that it is com-
pletely seated in its groove and securely fitted.
� Do not use self-locking nuts a few times over.
� Use a torque wrench to tighten fasteners to the torque values when specified. Wipe off grease or
oil if a thread is smeared with them.
� After reassembly, check parts for tightness and operation.
WARNING
� To protect environment, do not unlawfully dispose of used motor oil and other fluids: batteries, and tires.
� To protect Earth’s natural resouces, properly dispose of used vehicles and parts.
SERIAL NUMBER LOCATION

The frame serial number or V.I.N. (Vehicle Identification Number) is stamped on the steering head tube.
The engine serial number is located on the left downside of crankcase assembly.
These numbers are required especially for registering the machine and ordering spare parts.
◉ FRAME SERIAL NUMBER
◉ ENGINE SERIAL NUMBER

FUEL, OIL AND ENGINE COOLANT RECOMMENDATIONS

◉ FUEL
Gasoline used should be graded 91 octane (Research Method) or higher. An unleaded gasoline type is
recommended.
◉ ENGINE OIL
▣ ENGINE OIL SPECIFICATION
Classification system Grade
API Over SL
SAE 10W/40
※ If an SAE 10W/40 motor oil is not available, select an

alternative according to the following chart.
Use a premium quality 4-stroke motor oil to ensure

longer service life of your motorcycle.
WARNING
� Don’t mix the unrecommended oil. It could damage the engine.
� When refilling the oil tank, don’
t allow the dust to get inside.
� Mop the oil spilt.
� Don’t put the patch on the cap. It could disturb the oil to be provided and damage the engine.
◉ BRAKE FLUID
▣ Specification and classification (Front brake) : DOT3 or DOT4
(Rear brake) : DOT4
WARNING
Since the brake system of this motorcycle is filled with a glycol-based brake fluid by the manufacturer, do not
use or mix different types of fluid such as silicone-based and petroleum-based fluid for refilling the sys-
tem, otherwise serious damage will result.
Do not use any brake fluid taken from old or used or unsealed containers.
Never re-use brake fluid left over from a previous servicing, which has been stored for a long period.
◉ FRONT FORK OIL

▣ Use fork oil : TELLUS #32
◉ ENGINE COOLANT
Use an anti-freeze/engine coolant compatible with an aluminum radiator, mixed with distilled water only.
▣ WATER FOR MIXING

Use distilled water only. Water other than distilled water can corrode and clog the aluminum radiator.
▣ ANTI-FREEZE/ENGINE COOLANT
The engine coolant perform as a corrosion and rust inhibitor as well as anti-freeze. Therefore, the engine coolant
should be used at all times even though the atmospheric temperature in your area does not go down to freezing point.
Hyosung recommends the use of HYOSUNG COOLANT anti-freeze/engine coolant. If this is not available, use an
equivalent which is compatible with an aluminum radiator.
▣ LIQUID AMOUNT OF WATER/ENGINE COOLANT

For engine coolant mixture information, refer to cooling system section, page 5-1
CAUTION
Mixture of anti-freeze/engine coolant should be limited to 60%. Mixing beyond it would reduce its
efficiency. If the anti-freeze/engine coolant mixing ratio is below 50%, rust inhabiting performance
is greatly reduced. Be sure to mix it above 50% even though the atmospheric temperature does not
go down to the freezing point.
BREAK-IN PROCEDURES
During manufacture only the best possible materials are used and all machined parts are finished to a very high
standard but it is still necessary to allow the moving parts to“BREAK-IN”before subjecting the engine to maximum
stresses. The future performance and reliability of the engine depends on the care and restraint exercised during its
early life. The general rules are as follows :
● Keep to these break-in procedures :
Initial 800km Less than 1/2 throttle

Up to 1,600km Less than 3/4 throttle
● Upon reaching an odometer reading of 1,600 km you can subject the motorcycle to full throttle operation.
● Do not maintain constant engine speed for an extended period during any portion of the break-in. Try to vary the
throttle position.
CYLINDER CLASSIFICATION
The engine of is composed of the two cylinder, is classified into the front cylinder and rear cylin-
der as basis of the motorcycle ahead.
Rear cylinder
Front cylinder
⇒
FRONT
EXTERIOR ILLUSTRATION
SPECIFICATIONS
◉ DIMENSIONS AND DRY MASS

ITEM
Overall length 2,430 mm (95.7 in)
Overall width 840 mm (33.1 in)
Overall height 1,155 mm (45.5 in)
Wheelbase 1,665 mm (65.6 in)
Ground clearance 160 mm (6.3 in)
Mass 220 kg (485 lbs)
◉ ENGINE
ITEM
Type Four-stroke, DOHC, Liquid-cooled
Number of cylinder V-2 cylinder
Bore 81.5 mm (3.21 in)
Stroke 62.0 mm (2.44 in)
Piston displacement 647 ㎤ (39.5 in3 )
Carburetor BDSR39 TYPE (DOUBLE)
Starter system Electric starter
Lubrication system Wet sump
◉ TRANSMISSION
ITEM
Clutch Wet multi-plate type
Transmission 5-speed constant mesh
Gearshift pattern 1-down, 4-up
Final reduction 2.79
Gear ratio, 1st 2.46
2nd 1.78
3rd 1.38
4th 1.13
5th 0.96
Drive belt Poly chain belt
◉ CHASSIS
ITEM
Front suspension Telescopic type
Rear suspension Swingarm type
Steering angle 35°(right & left)
Caster 35°
Trail 160 mm (6.3 in)
Front brake Double disk brake
Rear brake Disk brake
Front tire size 120/70 - ZR 18 59W
Rear tire size 180/55 - ZR 17 73W
Front fork stroke 130 mm (5.12 in)
◉ ELECTRICAL
ITEM
Ignition type “Igniter”type
Ignition timing 5°B.T.D.C.at 1,500 rpm
Spark plug CR8E
Battery 12V 12Ah (MF)
Main : 30 A
Fuse
Head lamp : 15 A
HI : 60 W
Head lamp
LO : 55 W
Turn signal lamp 10 W×4
Brake / Tail lamp LED type
License plate lamp 5W
※ LED : Light Emitting Diode
◉ CAPACITIES
ITEM
Fuel tank 16.0 ℓ
Engine oil, oil change 3,000 ㎖
with filter change 3,200 ㎖
overhaul 3,400 ㎖
Front fork oil capacity (One side) 420 cc
NOTE
The specifications are subject to change without notice.
PERIODIC MAINTENANCE 2
CONTENTS
PERIODIC MAINTENANCE SCHEDULE ………………………… 2- 1 2

PERIODIC MAINTENANCE CHART …………………………………… 2- 1
LUBRICATION POINTS ………………………………………………… 2- 3
MAINTENANCE PROCEDURES …………………………………… 2- 4

VALVE CLEARANCE …………………………………………………… 2- 4
SPARK PLUG …………………………………………………………… 2- 6
EXHAUST PIPE BOLTS AND MUFFLER MOUNTING BOLTS……… 2- 7
AIR CLEANER …………………………………………………………… 2- 8
CARBURETOR …………………………………………………………… 2- 9
FUEL HOSE ……………………………………………………………… 2-10
CLUTCH …………………………………………………………………… 2-10
ENGINE OIL ……………………………………………………………… 2-12
ENGINE OIL FILTER …………………………………………………… 2-14
DRIVE BELT ……………………………………………………………… 2-15
BRAKE SYSTEM ………………………………………………………… 2-17
STEERING ………………………………………………………………… 2-21
FRONT FORK …………………………………………………………… 2-21
REAR SUSPENSION …………………………………………………… 2-21
TIRE ………………………………………………………………………… 2-22
CHASSIS BOLTS AND NUTS ………………………………………… 2-22
ENGINE COOLANT ……………………………………………………… 2-23
RADIATOR HOSE………………………………………………………… 2-25
COMPRESSION PRESSURE …………………………………………… 2-26
OIL PRESSURE ………………………………………………………… 2-27

2-1 PERIODIC MAINTENANCE
PERIODIC MAINTENANCE SCHEDULE

The chart below lists the recommended intervals for all the required periodic service work necessary to keep the
motorcycle operating at peak performance and economy.
CAUTION
More frequent servicing should be performed on motorcycles that are used under severe conditions.
PERIODIC MAINTENANCE CHART

▣ ENGINE
Interval
Initial 1,000 km Every 6,000 km Every 12,000 km page
Item
Air cleaner element Clean every 3,000 km Replace every 12,000 km 2-8
Exhaust pipe bolts and
Tighten Tighten ─ 2-7
muffler mounting bolts
Valve clearance adjust Inspect Inspect ─ 2-4
Cylinder head bolt Tighten Tighten ─ 3-50
Cylinder head & Cylinder ─ ─ Remove carbon 3-21
Spark plug Clean Clean Replace 2-6
Inspect Inspect ─
Fuel hose 2-10
Replace every 4 years
Engine oil filter Replace Replace ─ 2-14
Engine oil Replace Replace ─ 2-12
Throttle cable Inspect Inspect ─ 2-9
Idle speed Inspect Inspect ─ 2-9
Clutch Inspect Inspect ─ 2-10
Engine coolant Replace every 2 years 2-23
─ Inspect ─ 2-25
Radiator hoses
▣ CHASSIS
Interval
Initial 1,000 km Every 6,000 km Every 12,000 km page
Item
Drive belt Inspect every 1,000km 2-15
Brake Inspect Inspect ─ 2-17
Inspect Inspect ─
Brake hoses 2-17
Inspect Inspect ─
Brake fluid 2-17
Tires Inspect Inspect ─ 2-22
Steering Inspect Inspect ─ 2-21
Front forks ─ Inspect ─ 2-21
Rear suspension ─ Inspect ─ 2-21
Chassis bolts and nuts Tighten Tighten ─ 2-22
CAUTION
Using poor quality replacement parts can cause your motorcycle to wear more quickly and shorten its useful life.
Use only genuine Hyoung replacement parts or their equivalent.
PERIODIC MAINTENANCE 2-2
▣ FUEL TANK STAY

has the “fuel tank stay” under the seat.
Use the “fuel tank stay” to inspect the engine or the
other parts easily.
◆ USE OF FUEL TANK STAY

● Place the motorcycle on the side stand.
● Remove the seat by removing the seat mounting bolt
① on the seat tail cover.
①
● Remove the fuel tank mounting bolt ②.

● Take the fuel tank stay ③ off the tray upper the bat-
tery.
③
③ ②
● Lift the rear end of the fuel tank and prop it up as

shown illustration.
Insert the crank end of the fuel tank stay ③ into the
hole of the fuel tank and frame.
③
LUBRICATION POINT
Proper lubrication is important for smooth operation and long life of each working part of the motorcycle.
Major lubrication points are indicated below.
① Clutch lever holder and clutch cable ⑤ Speedometer gear box

② Passenger footrests pivot ⑥ Front brake lever holder
③ Side stand pivot and spring hook ⑦ Throttle cable
④ Footrests pivot ⑧ Rear brake pedal pivot
O - Motor oil, G - Grease
NOTE
� Before lubricating each part, clean off any rusty spots and wipe off any grease, oil, dirt or grime.
� Lubricate exposed parts which are subject to rust, with either motor oil or grease whenever the motor-
cycle has been operated under wet or rainy condition.
MAINTENANCE PROCEDURES
This section describes the service procedure for
each section of the periodic maintenance.
VALVE CLEARANCE
Inspect Interval
Inspect Initial 1,000 km and Every 6,000 km.
CAUTION
The clearance specification is for COLD state.
②
①
The valve clearance specification is different for
intake and exhaust valves.
Valve clearance adjustment must be checked and
adjusted,
1) at the time of periodic inspection,
2) when the valve mechanism is serviced, and
3) when the camshaft is disturbed by removing it
for servicing.
● Remove the radiator cover and radiator.
(Refer to page 2-6) [ FRONT CYLINDER ] [ REAR CYLINDER ]
● Using the fuel tank stay, lift the rear end of the fuel
tank and prop it up. (Refer to page 2-2)
● Remove the spark plug. (Refer to page 2-6)
● Remove the cylinder head cover ① and ②. ④
● Remove the magneto cover plug ③ and the tim-
ing inspection plug ④.
● Rotate the magneto rotor counter-clockwise to set
the front cylinder’s piston at TDC (Top Dead
Center) of the compression stroke.
(Rotate the rotor until“｜F”line on the rotor is aligned
with the center of hole on the crankcase.) ③
● To inspect the front cylinder’s valve clearance, insert

the thickness gauge to the clearance between the
camshaft and the tappet.
Valve clearance Standard (When cold)

IN. 0.1 � 0.2 mm (0.004 ~ 0.008 in)
EX. 0.28 � 0.32 mm (0.011 ~ 0.013 in)
Thickness gauge : 09900-20806

● If the clearance is out of specification, first remove the

cam chain tensioner, camshaft housing, camshaft.
To install the tappet shim at original position, record
the shim NO. and clearance to present by“A”,“B”,
“C”,“D”mark on the cylinder head.
Select the tappet that agree with tappet clearance

(vertical line) and shim NO.(horizontal line) as refer to the
tappet shim selection chart. (Refer to page 8-31∙32)
Adjust valve timing, install the camshaft housing and

the tensioner.
After the crankshaft rotate about 10 times, measure
the valve clearance.
If the clearance be not correct, adjust the standard
clearance as the same manner above.
● In case of valve adjustment which is not the tappet
shim selection chart, please follow instructions of
example in the below.
For example, the intake clearance is 0.4 and the shim
is 170 (1.70 mm), select 195 (1.95 mm) of the shim
which 170 (1.70 mm) of the shim add up the excess
clearance 0.25 mm when adjust with the standard
0.15 as the intake standard clearance 0.1�0.2 mm.
A B
CAUTION
� Valve clearance should be checked when the
engine is cold.
� If you don’ t rotate the crankshaft about 10
times before measuring the valve clearance, C D
there is no meaning of valve clearance.
● Rotate the magneto rotor to set the rear cylinder’s

piston at TDC(Top Dead Center) of the compression
stroke.
(Rotate the rotor 285�counter-clockwise from the
“｜F”line, and until the“｜R”line on the rotor is
aligned with the center of hole on the crankcase.)
● Inspect the rear cylinder’s valve clearance with the

same manner of the front cylinder.
SPARK PLUG
Inspect Interval
Clean Initial 1,000 km and Every 6,000 km,
Replace Every 12,000 km.
● Remove the four radiator cover mounting bolts.
● Remove the four radiator mounting bolts.
WARNING
The hot radiator and the hot engine can burn
you. Wait until the radiator and the engine are
cool enough to touch.
CAUTION
● Be careful not to damage the radiator fins.
● Do not extract the radiator hose.
● Remove the seat and fuel tank mounting bolts.

(Refer to page 2-2)
tank and prop it up.
● Disconnect the spark plug caps.

● Remove the spark plugs.
TYPE SPARK PLUG SPECIFICATION

Hot type CR7E
Standard type CR8E
Cold type CR9E
Remove the carbon deposit with wire or pin and adjust

the spark plug gap to 0.7�0.8 mm (0.028~0.032 in),
measuring with a thickness gauge.
Spark plug gap 0.7�0.8 mm (0.028~0.032 in)
Check to see the worn or burnt condition of the elec-

trodes.
If it is extremly worn or burnt, replace the plug.
And also replace the plug if it has a broken insula-
tor, damaged thread, etc.
● Install the spark plug, and then tighten it to speci-
fied torque.
Spark plug : 11 N∙m (1.1 kg∙m)
0.7 ~ 0.8 mm
(0.028 ~ 0.032 in)
EXHAUST PIPE BOLTS AND

MUFFLER MOUNTING BOLTS
Inspect Interval
Tighten Initial 1,000 km and Every 6,000 km.
● Tighten the exhaust pipe bolts ①, and muff ler

mounting bolts ② to the specified torque.
Exhaust pipe bolt
: 18~28 N∙m (1.8~2.8 kg∙m)
Muffler mounting bolt ①
: 18~28 N∙m (1.8~2.8 kg∙m) [ Front Cylinder ]
[ Rear Cylinder ]
AIR CLEANER ①
Inspect Interval
Clean Every 3,000 km,
Replace Every 12,000 km. ②
● Remove the seat.
● The air cleaner is located under the fuel tank.
Remove the fuel tank.
● Remove the four air cleaner inlet guide mounting
screws ①.
③
● Pull up the air cleaner inlet guide ② and the air
cleaner element ③.
Clean the air cleaner element for the following :

● When the air cleaner element clean with the air gun,
necessarily blow at the inside by compressed air.
● Carefully examine the air cleaner element for tears during
cleaning. Replace it with a new one if it is torn.
● Assemble the element completely or damage severely
the engine.
● Be careful not to allow water to go inside the air clea-
ner element.
CAUTION
More frequent servicing may be performed on mo-
torcycles that are used under severe condi-
tions, also clean the air cleaner element when
replacing the oil to prevent damage of the engine.
CARBURETOR
Inspect Interval
◉ IDLE SPEED
NOTE
Make this inspection when the engine is hot.
● Connect an engine tachometer to the high ten-

sion cord.
Start up the engine and set its speed at any-
where 1,300 and 1,500 rpm by turning throttle stop
screw �.
Engine idle speed 1,300�1,500 rpm

�
Engine tachometer : 09900-26006
▣ THROTTLE CABLE PLAY

This motorcycle has a twin throttle cable system. Cable ②
� is for throttle cable and cable � is for returning cable. ① �
There should be 0.5~1.0mm play on the throttle cable. �
To adjust the throttle cable play.
● Loosen the lock nut ① of the returning cable � and
fully turn in the adjuster ②.
● Loosen the lock nut ③ of the throttle cable �.
● Turn the adjuster ④ in or out until the throttle cable ③
play is between 0.5 ~ 1.0mm (0.02 ~ 0.04 in). ④
● Tighten the lock nut ③ while holding the adjuster ④. 0.5~1.0mm
● While holding the throttle grip at the fully closed posi- (0.02~0.04 in)
tion, slowly turn out the adjuster ② of the returning
cable � until resistance is felt.
● Tighten the lock nut ① while holding the adjuster ②. CAUTION
Throttle cable play 0.5�1.0 mm (0.02 ~ 0.04 in) Inadequate throttle cable play can cause engine
speed to rise suddenly when you turn the throttle
grip. This can lead to loss of rider control.
CAUTION
After the adjustment is completed, check that
throttle grip movement does not raise the
engine idle speed and that the throttle grip
returns smoothly and automatically.
FUEL HOSE
Inspect Interval
Inspect Initial 1,000 km and Every 6,000 km,
Replace every 4 years.
● Remove the seat. (Refer to page 7-1)

● Remove the fuel tank. (Refer to page 4-1)
● Remove the frame cover. (Refer to page 7-2)
Inspect the fuel hoses for damage and fuel leakage.
If any defects are found, the fuel hoses must be
replaced.
CLUTCH
⑤
Inspect Interval ②
Clutch play should be 2 mm (0.08 in) as measured at the

clutch lever holder before the clutch begins to disengage.
If the play in the clutch is incorrect, adjust it in the following
way :
● A basis adjustment be allowed by the clutch lever
adjuster ②. ① �
● Loosen the clutch lever adjuster ②.
● Screw the lock nut ① clockwise fully, after finishing
adjustment.
● After end of adjustment, tighten the lock nut ① and
cover the rubber boot ⑤.
● If not adjust by the adjuster ②, loosen the clutch
cable adjuster lock nut ③.
● Turn the clutch cable adjuster ④ in or out to acquire
the specified play.
● After end of adjustment, tighten the lock nut ③.
● The clutch cable should be lubricated with a light
weight oil whenever it is adjusted.
Clutch cable play � 2 mm (0.08 in) ③ ④
◉ GEARSHIFT LEVER HEIGHT ADJUSTMENT

● Loosen the lock nut ⑥.
● With the link rod ⑦ turned, adjust the gearshift lever
height.
● Tighten the lock nut ⑥.
⑥
⑦ ⑥
▣ FOOTREST POSITION ADJUSTMENT

has 2 type of the footrest position, right
and left.
To change the position, remove the footrest mounting
bolt ①, footrest boss cap ② and bolt ③.
Install the bolt ① to the desired position and footrest
boss cap ②, bolt ③ to the position �.
is delivered from the factory on position

�.
①
WARNING
When adjusting the footrest position, the footrest
mounting bolt be torque to the proper specifica-
tion.
If they are not, the footrest can come off unexpect-
edly. ② ③
Footrest mounting bolt
[ POSITION � ]
: 40~60 N∙m (4.0~6.0 kg∙m)
� ②
▣ GEARSHIFT LINK ROD ③
When the footrests in position �, exchange the
gearshift link rod for appropriate riding position.
● Position �
: Install the gearshift link rod ④
● Position �
: Install the gearshift link rod ⑤ ①
[ POSITION � ]
⑤
ENGINE OIL
Inspect Interval
Replace Initial 1,000 km and Every 6,000 km.
Necessary amount of engine oil

Oil change 3,000 ㎖
Filter change 3,200 ㎖
Overhaul engine 3,400 ㎖
Engine oil type SAE 10W/40

API Over SL
Oil should be changed while the engine is warm. Oil fil-

ter replacement at the above intervals, should be
together with the engine oil change. ①
● Keep the motorcycle upright.
● Place an oil pan below the engine, and drain the
oil by removing the filler cap ① and drain plug ②.
● Tighten the drain plug ② to the specified torque, and
pour fresh oil through the oil filler. Use an API classi-
fication of Over SL oil with SAE 10W/40 viscosity.
Oil drain plug : 21 N∙m (2.1 kg∙m)
②
● Start up the engine and allow it to run for sever-

al minutes at idling speed.
● Turn off the engine and wait about three minutes,

then check the oil level through the inspection win-
F
dow. If the level is below mark“L”, add oil to“F”level.
If the level is above mark“F”, drain oil to“F”level.
L
CAUTION
Never operate the motorcycle if the engine oil level
is below the“Lower line mark(L)”in the inspec-
tion window. Never fill the engine oil above the
“Upper line mark(F)”.
Engine oil level being most suitable about 1mm under
the“Upper line mark(F)”of the engine oil lens. In
case of the engine oil pouring in excessively, the
engine output being made insufficient.
Be careful not to pour the oil excessively into
engine.
CAUTION
�
Necessarily, confirm and clean the oil strainer �
when replace the engine oil (specially, when first
replacement).
CAUTION
More frequent servicing may be performed on mo-
torcycles that are used under severe conditions.
ENGINE OIL FILTER

Inspect Interval ②
Replace Initial 1,000 km and Every 6,000 km.
● Drain the engine oil as described in the engine oil

replacement procedure.
● Remove the oil filter cap ①.
● Remove the oil filter. ①
● Install the new O-ring ②.
● Install the new oil filter.

● Install the new O-ring ③ and spring ④ to the oil filter
cap. ③
● Install the oil filter cap.
④
CAUTION
Before installing the oil filter cap, apply engine
oil lightly to the new O-ring ③.
▣ OIL FILTER INSTALLATION

INSERTION
CAUTION DIRECTION
� LUSTER MATERIAL
When install the oil filter, necessarily,“HYOSUNG”

character and“16510HN910”part’s NO. install to-
ward the outside, otherwise can damage the engine.
WARNING �
Engine oil and exhaust pipes can be hot enough to HYOSUNG
burn you. 16510HN910 OUTSIDE
Wait until the oil drain plug and exhaust pipes are
cool enough to touch with bare hands before drain-
ing oil.
● Add new engine oil and check the oil level as

described in the engine oil replacement procedure.
F
CAUTION
Use HYOSUNG MOTORS GENUINE OIL FILTER L
only, since the other make’ s genuine filters and
after-market parts may differ filtering perfor-
mance and durability, which could cause engine
damage or oil leaks. Hyosung motors genuine oil
filter is also not usable for the motocycles.
DRIVE BELT
Inspect Interval
Inspect Every 1,000 km.
Visually check the drive belt for the possible defects
listed below. (Support the motorcycle by the jack
or block, turn the rear wheel slowly by hand with the
transmission shifted to Neutral.)
● Edges of the belt for cuts or unusual wear patterns NOTE
● Outside ribbed surface of the belt for sign of stone
When replacing the drive belt, replace the
puncture
drive belt and pulleys as a set.
● Roots of the belt teeth
● Sign of cracking at the base of the belt teeth
● Common types of belt wear and damage
● Improper belt adjustment �
If any defects are found, the drive belt must be
replaced.
Damage to the drive belt means that the pulleys
may also be damaged.
If any defects are found, the pulleys must be �
replaced.
�
▣ ADJUSTMENT OF DRIVE BELT SLACK �
● Loosen the axle bolt �.
● Loosen the lock nuts �, �.
● Loosen or tighten both belt adjusters �, � until the
belt has specification of slack in the belt case
inspection hole. The marks �, � on both belt �
adjusters must be at the same position on the scale
to ensure that the front and rear wheels are correctly
aligned.
� �
DRIVE BELT SLACK (4.5kg of Force)
When the rear tire is touched the ground 4.5~5.5 mm

(0.18~0.22 in)
5.0~6.0 mm
When the rear tire is not touched the ground
(0.20~0.24 in)
● Place the motorcycle on jack or block for accurate

Rear pulley
adjustment. Engine pulley
● After adjusting the drive belt, tighten the axle bolt
Belt case
to the specified torque.
inspection hole
Rear axle bolt : 90~140 N∙m (9.0~14.0 kg∙m)
● Tighten both belt adjuster lock nuts �, � securely.

↑
4.5 kg of Force
See Table
● Recheck the drive belt slack after tightening the

rear axle bolt.
WARNING
Be careful not to touch the muffler when it is hot :
a hot muffler can burn you.
CAUTION
The drive belt for this motorcycle is made of the
special material.
The belt should be replaced with a “Poly chain
belt” for .
Use of another belt may lead to premature belt
failure.
▣ CAUTION OF DRIVE BELT

When the drive belt was bent excessively, the belt inner Never clamp or bend
cord is broken.
Never bend the drive belt under the specification of
inner or back bend capacity.
� �
BEND CAPACITY OF DRIVE BELT
Inner least 102 mm (4.02 in)
Back least 204 mm (8.04 in)
※ � Back bend � Inner bend

CAUTION
● Never bend or twist when the drive belt is kept
or installed.
● If the drive belt was installed with driver
forcedly, damage the drive belt.
BRAKE SYSTEM
Inspect Interval
[ BRAKE ]
[ BRAKE HOSES & BRAKE FLUID ]
Replace the brake hoses Every 4 years,
Replace the brake fluid Every 2 years. CAUTION
Do not spill any brake fluid on the brake pad of
▣ BRAKE FLUID LEVEL CHECK
disk.
● Keep the motorcycle upright and place the handle-
bars straight.
● Check the brake fluid level by observing the lower
limit line (LOWER) on the front or rear brake fluid
reservoir.
● When the level is below the lower limit line (LOWER),
replenish with brake fluid that meets the following LOWER
specification.
Specification and Classification
(Front brake) : DOT 3 or DOT 4
(Rear brake) : DOT 4
WARNING
The brake system of this motorcycle is filled with [ Front Brake ]
a glycol-based brake fluid. Do not use or mix dif-
ferent types of fluid such as silicone-based or
petroleum-based. Do not use any brake fluid
taken from old, used or unsealed containers.
Never re-use brake fluid left over from the last
servicing or stored for a long period.
LOWER
WARNING
Brake fluid, if it leaks, will interfere with safe run-
ning and immediately discolor painted surfaces.
Check the brake hoses and hose joints for cracks
and oil leakage before riding. [ Rear Brake ]
▣ BRAKE PAD WEAR

The extend of brake pad wear can be checked
by observing the grooved limit � on the pad. When
the wear exceeds the grooved limit, replace the pads
with new ones.
CAUTION
Replace the brake pad as a set, otherwise braking �
performance will be adversely affected.
▣ FRONT AND REAR BRAKE PAD

REPLACEMENT
● Remove the brake caliper.
● Remove the brake pads.
● To reassemble, reverse the above sequence.
Front brake caliper mounting bolt

: 18~28 N∙m (1.8~2.8 kg∙m)
Rear brake caliper mounting bolt
: 18~28 N∙m (1.8~2.8 kg∙m)
[ Left side of Front Brake ]
[ Right side of Front Brake ]
▣ FRONT AND REAR BRAKE FLUID

REPLACEMENT
● Place the motorcycle on a level surface and keep the [ Rear Brake ]
handlebars straight.
● Remove the master cylinder reservoir cap and diaphragm.
● Suck up the old brake fluid as much as possible.
● Fill the reservoir with new brake fluid.
Specification and Classification
● Connect a transparent hose ① to the air bleeder

valve and insert the other end of the hose into a ①
receptacle.
● Loosen the air bleeder valve and pump the brake

lever until the old brake fluid is completely out of the
brake system.
● Close the air bleeder valve and disconnect the

transparent hose. Fill the reservoir with new brake
fluid to the upper line.
● Replace the rear brake’s fluid with the same man-
ner of the front brake.
Front brake caliper air bleeder valve
: 6~8 N∙m (0.6~0.8 kg∙m)
Rear brake caliper air bleeder valve
: 6~8 N∙m (0.6~0.8 kg∙m)
▣ AIR BLEEDING OF THE BRAKE FLUID

CIRCUIT
Air trapped in the brake fluid circuit acts like a cushion to
absorb a large proportion of the pressure developed by
the master cylinder and thus interferes with the full brak-
ing performance of the brake caliper. The presence of
air is indicated by“sponginess”of the brake lever and
also by lack of braking force. Considering the danger
to which such trapped air exposes the machine and
rider, it is essential that, after remounting the
brake and restoring the brake system to the normal
condition, the brake fluid circuit be purged of air in the fol-
lowing manner :
● Fill the master cylider reservoir to top of the inspec-
tion window. Replace the reservoir cap to prevent dirt
from entering it.
● Attach a hose to the air bleeder valve, and insert
the free end of the hose into a receptacle.
● Bleed air from the brake system.
● Squeeze and release the brake lever several times

in rapid succession and sqeeze the lever fully with-
out releasing it. Loosen the bleeder valve by turn-
ing it a quarter of a turn so that the brake fluid runs
into the receptacle, this will remove the tension of
LOWER
the brake lever causing it to touch the handlebar
grip. Then, close the air bleeder valve, pump and
squeeze the brake lever, and open the valve.
Repeat this process until the fluid flowing into the
receptacle no longer contains air bubbles.
NOTE
While bleeding the brake system, replenish the
brake fluid in the reservoir as necessary. Make
sure that there is always some fluid visible in
the reservoir.
● Close the air bleeder valve, and disconnect the hose.

Fill the reservoir with brake fluid to the upper line.
● Bleed the rear brake’s air with the same manner of
front brake.
Front brake caliper air bleeder valve
: 6~8 N∙m (0.6~0.8 kg∙m)
Rear brake caliper air bleeder valve
: 6~8 N∙m (0.6~0.8 kg∙m)
CAUTION
Handle brake fluid with care : the fluid reacts ①
chemically with paint, plastics, rubber materials, etc.
▣ FRONT BRAKE LAMP SWITCH

The front brake lamp switch ① is located beneath the front
brake lever. Loosen the switch fitting screws and adjust the
timing by moving the switch body forward or backward.
▣ REAR BRAKE LAMP SWITCH

Adjust the rear brake lamp switch ② so that the brake
lamp will come on just before pressure is felt when the
brake pedal is depressed.
②
STEERING
Inspect Interval
Steering should be adjusted properly for smooth turning

of handlebars and safe running. Overtight steering pre-
vents smooth turning of the handlebars and too
loose steering will cause poor stability. Check that
there is no play in the steering stem while grasping
the lower fork tubes by supporting the machine so that
the front wheel is off the ground, with the wheel straight
ahead, and pull forward. If play is found, perform
steering stem nut adjustment as described in page
7-30 of this manual.
FRONT FORK
Inspect Interval
Inspect the front forks for oil leakage, scoring or scratch-

es on the outer surface of the inner tubes. Replace any
defective parts, if necessary.
REAR SUSPENSION
Inspect Interval
Inspect the rear shock absorber for oil leakage and

mounting rubbers including engine mounting for wear
and damage. Replace any defective parts, if neces-
sary. (Refer to page 7-38)
TIRE Tire wear indicator
Inspect Interval
▣ TIRE TREAD CONDITION

Operating the motorcycle with excessively worn tires will
decrease riding stability and can lead to loss of control.
● Inspect shortage of tire thread’ s depth by the� tire
wear indicator �.
● Replace the front and rear tires at once when appear Tire wear indicator mark
the� tire wear indicator �.
▣ TIRE PRESSURE CAUTION

If the tire pressure is too high or too low, steering will
be adversely affected and tire wear increased. The standard tire on is
Therefore, maintain the correct tire pressure for good 120/70-ZR 18 59W for front and
enter key roadability or shorter tire life will result. Cold 180/55-ZR 17 73W for rear.
inflation tire pressure is as follows. The use of tires other than those specified
may cause instability. It is highly recommended to
COLD INFLATION SOLO RIDING DUAL RIDING use a HYOSUNG Genuine Tire.
TIRE PRESSURE KPa kgf/cm2 psi KPa kgf/cm2 psi
Front 221 2.25 33.0 221 2.25 33.0
Rear 245 2.50 36.0 285 2.90 42.0
CHASSIS BOLTS AND NUTS

Inspect Interval
Tighten Initial 1,000 km and Every 6,000 km.
Check that all chassis bolts and nuts are tightened to

their specified torque. (Refer to page 8-13)
ENGINE COOLANT
Inspect Interval
Replace the engine coolant Every 2 years.
▣ ENGINE COOLANT LEVEL CHECK

● Keep the motorcycle upright.
● Check the engine coolant level by observing the full
line(F) and lower line(L) on the engine coolant
reserve tank.
● If the level is below the lower line(L), add engine
coolant to the full line from the engine coolant
reserve tank filler ①.
Engine coolant capacity
Reserve tank side 230 ㎖
Radiator side 430 ㎖
Engine side 940 ㎖
WARNING ①
● Engine coolant is harmful if swallowed or if it
comes in contact with skin or eyes.
● Keep out of the reach of children and animals.
CAUTION
● Use distilled water only. Water other than distilled
water can corrode and clog the aluminum radia-
tor.
● The 50 : 50 mixture of distilled water and ethylene
glycol anti-freeze will provide the optimum corro-
sion protection and excellent heat protection, and
will protect the cooling system from freezing at
temperatures above -31℃(-24℉).
NOTE
Bleed air from the cooling circuit when the engine
overheat.
▣ OPEN THE RADIATOR CAP

Remove the right front side cover ① to operate the
radiator cap ③.
To disassemble the right front side cover ①, remove
the two mounting bolt ②. ①
WARNING
You can be injured by scalding fluid or steam if
you open the radiator cap when engine is hot.
After the engine cools, wrap a thick cloth around ②
cap and carefully remove the cap by turning it a
quarter to allow pressure to escape and then turn
the cap all the way off.
▣ ENGINE COOLANT CHANGE
WARNING
Do not open the radiator cap when the engine is
hot, as you may be injured by escaping hot liquid
or vapor.
● Remove the right front side cover ①.

● Remove the radiator cap ③.
● Drain engine coolant by removing the drain bolt ④.
● Flush the radiator with fresh water if necessary.

● Install the water hose.
④
● Tighten the coolant drain bolt ④ to the specified
torque.
Coolant drain bolt
: 11~14 N∙∙m (1.1~1.4 kg∙ ∙m)
● Pour the engine coolant through the radiator cap
inlet.
Engine coolant capacity
Reserve tank side 230 ㎖
Radiator side 430 ㎖
Engine side 940 ㎖
● Bleed the air from the engine coolant circuit as fol-
lowing procedure.
NOTE
For engine coolant information, refer to page 5-1
▣ AIR BLEEDING THE COOLING CIRCUIT

● Add engine coolant up to the raditor cap inlet.
● Support the motorcycle upright.
● Slowly swing the motorcycle, right and left, to bleed
the air trapped in the cooling circuit.
● Add engine coolant up to the radiator cap inlet.
● Start up the engine and bleed air from the radiator

cap inlet completely.
● Add engine coolant up to the radiator cap inlet.
● Repeat the above procedure until no air bleed from
the radiator cap inlet.
● Close the radiator cap securely.

● After warming up and cooling down the engine sev-
eral times, add the engine coolant up to the full
line(F) of the reserve tank.
CAUTION
Repeat the above procedure several times and
make sure that the radiator is filled with engine
coolant up to the reserve tank full line(F).
RADIATOR HOSE
Inspect Interval
Inspect Every 6,000km,
Replace the radiator hoses Every 4 years.
Check to see the radiator hoses for crack, damage or

engine coolant leakage.
If any defects are found, replace the radiator hoses with
new ones.
COMPRESSION PRESSURE
The compression of a cylinder is a good indicator of
Low compression pressure can indicate some of the
its internal condition.
following conditions :
The decision to overhaul the cylinder is often based
● Excessively worn cylinder wall
on the results of a compression test. Periodic mainte-
● Worn-down piston or piston rings
nance records kept at your dealership should include
● Piston rings stuck in grooves
compression reading for each maintenance service.
● Poor seating of valves
Compression pressure ● Ruptured or otherwise defective cylinder head gasket
Standard 14 kg/cm2 (at 500 rpm)
Service limit 12 kg/cm2 (at 500 rpm)
Difference 2 kg/cm2 (at 500 rpm)
▣ COMPRESSION TEST PROCEDURE

NOTE
� Before testing the engine for compression
pressure, make sure that the cylinder head
bolts are tightened to the specified torque
values and valves are properly adjusted.
� Have the engine warmed up by idling before
testing.
� Be sure that the battery used is in fully-
charged condition.
Remove the parts concerned and test the compres-
sion pressure in the following manner.
● Loosen the radiator cover mounting bolts from the
frame.
● Loosen the radiator mounting bolts.
WARNING
The hot radiator and the hot engine can burn you.
Wait until the radiator and the engine are cool
enough to touch.
CAUTION
● Be careful not to damage the radiator fins.
● Do not extract the radiator hose.
tank and prop it up. (Refer to page 2-2)
● Remove all the spark plug. Overhaul the engine in the following cases :
● Fit the compression gauge in one of the plug holes, ● Compression pressure in one of the cylinder is less
while taking care that the connection is tightened. than 12kg/㎠.
● Keep the throttle grip in full-open position. ● The difference in compression pressure between two
● Crank the engine a few seconds with the starter, and cylinder is more than 2kg/㎠.
record the maximum gauge reading as the compres- ● All compression pressure readings are nearly 12kg/㎠
sion of cylinder. even when they measure more than 12kg/㎠.
Compression gauge : 09915-64510
OIL PRESSURE
Check the oil pressure periodically. This will give a good indication of the condition of the moving parts.
Standard
Oil pressure 2.0 ~ 6.0 ㎏/㎠
(at 60 ℃∙3,000 rpm)
If the oil pressure is lower or higher than the specification, the following causes may be considered.
▣ LOW OIL PRESSURE

● Oil leakage from the oil passage
● Damaged O-ring
● Defective oil pump
● Combination of above items
▣ HIGH OIL PRESSURE

● Engine oil viscosity is too high
● Clogged oil passage
● Combination of the above items
▣ OIL PRESSURE TEST PROCEDURE

Check the oil pressure in the following manner.
● Remove the oil check plug and install the adapter of oil
pressure gauge at the removed position.
● Connect an engine tachometer.
● Warm up the engine as follows :
Summer : 10 min. at 2,000 rpm.
Winter : 20 min. at 2,000 rpm.
● After warming up, increase the engine speed to
3,000 rpm. (with the engine tachometer), and read
the oil pressure gauge.
Engine tachometer : 09900-26006

Oil pressure gauge : 09915-74510
ENGINE
CONTENTS
ENGINE REMOVAL AND REINSTALLATION …………………… 3- 1

ENGINE REMOVAL ……………………………………………………… 3- 1
ENGINE REINSTALLATION …………………………………………… 3- 7 3
ENGINE DISASSEMBLY ………………………………………………… 3- 9
STARTER MOTER ……………………………………………………… 3- 9
THERMOSTAT …………………………………………………………… 3- 9
2ND AIR VALVE ………………………………………………………… 3-10
CYLINDER HEAD COVER ……………………………………………… 3-10
PISTON …………………………………………………………………… 3-14
MAGNETO COVER ……………………………………………………… 3-14
MAGNETO ROTOR ……………………………………………………… 3-15
CLUTCH COVER ………………………………………………………… 3-16
CLUTCH …………………………………………………………………… 3-17
PRIMARY DRIVE GEAR ………………………………………………… 3-18
OIL PUMP ………………………………………………………………… 3-18
GEARSHIFT SHAFT……………………………………………………… 3-19
ENGINE COMPONENT INSPECTION AND SERVICE ……… 3-21
ENGINE REASSEMBLY ………………………………………………… 3-39
CAUTION
� Mark an identification of assembly location on each removed part so that each will be restored
to the original position during reassembly.
� Wash clean and dry the removed parts before inspecting and measuring.
� Oil the rotating or sliding parts before assembly.
� Make sure to use the correct type of lubricant where specified.
� Check that each rotating or sliding part moves or operates smoothly after assembly.
� Make sure to follow the bolt tightening order where specified.
� If the correct length of the bolt is confused when tightening the crankcase or cover, insert all the bolts
and check that the tightening margin is equal in each bolt.
3-1 ENGINE
ENGINE REMOVAL AND

REINSTALLATION
ENGINE REMOVAL ①
NOTE
If the engine is dirtied, wash the machine
with a suitable cleaner before removing the
engine.

● Remove the frame cover. (Refer to page 7-2)
● Disconnect the battery � lead wire ①.
CAUTION
First, disconnect the � lead wire.
● Drain engine oil. (Refer to page 2-12)
● Drain engine coolant. (Refer to page 2-24)
▣ AIR CLEANER
● With the four hose and the two clamp screw loos-
ened, remove the air cleaner case.
ENGINE 3-2
▣ COOLING FAN
● With the two mounting bolts ② removed, remove the
right front side cover ①.
● Remove the radiator cap bolt ③.
①
③ ②
● Remove the four radiator cover mounting bolts.
● Remove the radiator cover.
● Disconnect the radiator outlet hose ④.
● Remove the radiator mounting bolts.
● Disconnect the cooling fan thermo-switch lead wire

coupler ⑤. ⑥
● Disconnect the radiator inlet hose ⑥.
● Disconnect the reserve tank hose ⑦.

● Disconnect the cooling fan motor lead wire coupler
⑧. ⑧ ⑦
● Remove the radiator.
CAUTION
Be careful not to bend the radiator fin.
3-3 ENGINE
▣ CARBURETOR
● Remove the carburetor after removed the intake pipes.
(Refer to page 4-4)
● Disconnect the vacuum hoses ①.
▣ CLUTCH CABLE
● Disconnect the clutch cable end out of clutch lever.
● Disconnect the clutch cable end out of clutch release
arm.
▣ EXHAUST PIPE AND MUFFLER

● With the exhaust pipe bolts �, rear exhaust pipe
connecting bolts � and muffler mounting bolts �
removed, remove the exhaust pipes and muffler.
�
[ Front Cylinder ]
[ Rear Cylinder ]
ENGINE 3-4
▣ ELECTRIC PARTS
● By taking out the spark plug caps, remove the spark
plug.
[ Front Cylinder ] [ Rear Cylinder ]

● Remove the starter motor lead wire.
● Disconnect the engine coolant temperature sensor

lead wire ①. ①
3-5 ENGINE
● Remove the engine ground lead wire ①.
● Disconnect the two magneto coupler ②.

● Disconnect the neutral switch terminal ③. ③ ②
● Disconnect the side-stand switch lead wire couper
④.
▣ ENGINE PULLEY
● Remove the engine pulley cover ⑤.
● Disconnect the front side of crankcase breather hose

⑥ and rear side of crankcase breather hose ⑦.
⑦
ENGINE 3-6
● Remove the gearshift arm ①.

● Flatten the lock washer.
● Remove the engine pulley nut ② and washer.
②
NOTE
When loosening the engine pulley nut, depress
the brake pedal.
● Remove the engine pulley.
NOTE
If it is difficult to remove the engine pulley,
loosen the rear axle bolt, belt adjusters ③ ∙ ④
to provide additional belt slack.
(Refer to page 2-15)
③ ④
● Remove the frame down tube.

● Support the engine using an engine jack.
● Remove the engine mounting nuts, bolts and engine
mounting lock nuts with the special tool.
Engine mounting socket wrench (M20)

: 09940H30010
● Remove the engine from the frame.
CAUTION
Remove the carburetor when removing or
installing the engine necessarily.
When removing the carburetor, loosen the intake
pipe mounting bolts at the same time.
3-7 ENGINE
ENGINE REINSTALLATION CAUTION

Reinstall the engine in the reverse order of engine Set the part � of engine mounting bolt ① align
removal. center line by the hand temporarily and install
● Install the engine mounting bolts, nuts and engine the engine mounting bolt to the specified
mounting lock nuts with the special tool. torque.
Engine mounting socket wrech (M20) If otherwise, it is damage to the thread of
: 09940H30010 engine mounting bolt.
● Tighten the engine mounting bolts, nuts and engine
mounting lock nuts to the specified torque. NOTE
Engine mounting bolt ①, ②
�30 N∙
: 15� ∙m (1.5� �3.0 kg∙
∙m) Set the part � of swingarm pivot shaft �
Engine mounting nut ③ align center line by the hand temporarily
�70 N∙
: 45� ∙m (4.5� �7.0 kg∙
∙m) and install the swingarm pivot shaft to the
Engine mounting lock nut (M20) ④ specified torque.
: 35 ~ 50 N∙ ∙m (3.5� �5.0 kg∙
∙m) Swingarm pivot shaft �
● Tighten the frame down tube mounting bolts ⑤ to the : 15~30 N ∙ m (1.5~3.0 kg ∙ m)
specified torque. Swingarm pivot nut �
Frame down tube mounting bolt ⑤ : 50~70 N ∙ m (5.0~7.0 kg ∙ m)
: 22 ~ 35 N∙ ∙m (2.2� �3.5 kg∙
∙m) Swingarm mounting lock nut (M26) �
: 70~80 N ∙ m (7.0~8.0 kg ∙ m)
③ �
①
�
③ �
�
①
�
�
④
⑤
②
ENGINE 3-8
▣ ENGINE PULLEY
● Loosen the rear axle bolt ① and belt adjusters ②,
left and right.
● Install the engine pulley.
② ①
②
● Tighten the engine pulley nut ③ to the specified
torque.
Engine pulley nut

: 130~160 N∙m (13.0~16.0 kg∙m)
NOTE
When tightening the engine pulley nut,
depress the rear brake pedal.
● Bend the lock washer securely.
● Install the gearshift arm and adjust the gearshift lever ③

height. (Refer to page 2-10)
● Install the breather hose and engine pulley cover.

● Connect each electric parts and its couplers.
(Refer to page 8-24~30)
● Install the exhaust pipes and mufflers.
● Install the carburetor and air cleaner.
(Refer to page 4-7)
● Install the radiator and radiator cover.
(Refer to page 5-4)
● Af t e r r e m o u n t i n g t h e e n g i n e , t h e f o l l o w i n g
adjustments are necessary.
Engine idling speed Refer to page 2-9
Throttle cable play Refer to page 2-9
Clutch cable play Refer to page 2-10
Drive belt Refer to page 2-15
Gearshift lever height Refer to page 2-10
Engine oil level Refer to page 2-13
Engine coolant Refer to page 2-23
3-9 ENGINE
ENGINE DISASSEMBLY
CAUTION
Identify the position of each removed part.
Organize the parts in their respective groups so
that they can be reinstalled in their original
positions.
STARTER MOTOR
● Remove the starter motor.
● Remove the gear position switch.

● Remove the contacts ① and springs ②.
②
①
THERMOSTAT ③
● Remove the thermostat case ③ along with the hose
④.
NOTE
Thermostat inspection and servicing
: Refer to page 5-8
④
ENGINE 3-10
2ND AIR VALVE

● Remove the 2nd air valve ① with the bracket.
①
CYLINDER HEAD COVER

● Remove the cylinder head cover.
● To set the piston at TDC (Top Dead Center).
CAUTION
Align the index mark on the magneto rotor with
the index mark on the magneto cover as turn the
crankshaft counter-clockwise.
To set piston at TDC(Top Dead Center) of the
compression stroke as align the“｜F”mark for
front cylinder and the“｜R”mark for rear cylin-
der.
● Remove the cam chain tensioner adjuster �, �.
[ Front Cylinder ]
3-11 ENGINE
[ Rear Cylinder ]
● With the three bolts removed, remove the cam chain
guide NO.2 ①.
● Remove the camshaft housing ②.
NOTE
Mark an identification of assembly location on
each removed parts so that each will be ②
restored to the original position during
reassembly.
● Remove the camshaft (IN.∙EX.) ③.

③
ENGINE 3-12
● Loosen the cylinder head base bolt.
● Loosen the six cylinder head bolts.
NOTE
When loosening the cylinder head bolts,
loosen each bolt little by little diagonally.
● Remove the chain guide NO.1 and cylinder head.
● Remove the tappet and the shim.
CAUTION
Draw out the tappet and shim with the strong
magnet not to be scratched.
3-13 ENGINE
CAUTION
The tappet and shim should be lined so that each
will be restored to the original position during
reassembly.
● Compress the valve spring by using the special tool.
Valve spring compressor : 09916-14510

Valve spring compressor attachment
: 09916-14520
● Take out the valve cotter from the valve stem.

● Remove the valve spring retainer.
● Pull out valve from the other side.
● Remove the two cylinder base nuts and cylinder.
CAUTION
If tapping with the plastic hammer is necessary,
pay attention to break the fins.
ENGINE 3-14
● Remove the rear cylinder head and cylinder with the Rear Cylinder
same manner of the front cylinder head and cylinder
removal. Front Cylinder
PISTION
● Place a clean rag over the cylinder base to prevent
piston pin circlips from dropping into crankcase.
Remove the piston pin circlips with long-nose pliers.
● Remove the piston pin by using the special tool.
Piston pin puller : 09910-34510
NOTE
Make an identification on each piston head to
confirm the cylinder.
MAGNETO COVER
● Remove the magneto cover.
3-15 ENGINE
● Remove the starter idle shaft ①, starter idle gear

②.
MAGNETO ROTOR
● With the magneto rotor held immovable using the
special tool, loosen the rotor nut.
Conrod holder : 09910-20115
● Remove the magneto rotor by using the special tool.

Rotor remover : 09930-30165
● Remove the key ③.

● Remove the starter driven gear ④.
● Remove the cam chain ⑤. ③
⑤
ENGINE 3-16
● Remove the cam chain tensioner ①.

①
CLUTCH COVER ②
● Remove the clutch release arm ②.
● Remove the clutch cover bolts.

● Remove the clutch cover ③.
③
NOTE
When remove or inspect the clutch drive and
driven plate, remove only the clutch pressure
cover ④.
3-17 ENGINE
CLUTCH
● With the primary drive gear held immovable using
the special tool, remove the clutch spring mounting
bolts diagonally.
● Remove the disk pressure ①.
①
● Remove the clutch drive plates NO. 1 and driven
plates.
● Remove the spring washer and spring washer seat.
● Remove the clutch drive plate NO. 2.
● Flatten the lock washer ②.
● With the clutch sleeve hub held immovable using

special tool, remove the clutch sleeve hub nut.
Clutch sleeve hub holder : 09920-53710

ENGINE 3-18
● Remove the clutch sleeve hub ① and primary driv-

en gear assembly ② .
②
①
PRIMARY DRIVE GEAR

● With the crankshaft held immovable using special
tool, remove the primary drive gear nut ③.
● Remove the water pump drive gear ④ and primary
drive gear ⑤.
④
CAUTION
This nut has left-hand thread. If turning it counter- ③
clockwise ( ), it may cause damage. ⑤
Pay attention at the primary drive gear nut with
a washer, and water pump drive gear with a
washer.
⑥
● Remove the cam chain ⑥.
● Remove the cam chain tensioner ⑦.
⑦
OIL PUMP
● Remove the circlip ⑧ and oil pump driven gear ⑨.
⑨
⑧
3-19 ENGINE
● Remove the pin ① and shim.

● With the three screws loosened, remove the oil
pump ②.
②
GEARSHIFT SHAFT
● Draw out the gearshift shaft ③.
③
● Remove the gearshift cam stopper ④.
● Loosen the gearshift cam plate bolt ⑤.
● Remove the gearshift cam stopper plate. ⑤
● Remove the crankcase securing bolts, right and left.
NOTE
Loosen the crankcase bolts diagonally and
smaller sizes first.
ENGINE 3-20
● Remove the mission oil pipe mounting bolt.
● Separate the crankcase into 2 parts, right and left,

with a special tool.
Crankcase separator : 09920-13120
CAUTION
When separating the crankcase, necessarily,
remove it after installed the special tool
(Crankcase separator) on the side of clutch.
In case separate oppositely, the gearshift cam
stopper will be damaged in the side of magneto.
NOTE
Fit the crankcase separater, so that the tool
arms parallel the side of the crankcase.
● Remove the gearshift fork shaft ① and gearshift

fork ②.
● Remove the gearshift cam ③.
① ⑤
● Remove the driveshaft assembly ④, countershaft
assembly ⑤. ④ ②
②
③
3-21 ENGINE
● Remove the crankshaft by using the special tool.

Crankcase separator : 09920-13120
ENGINE COMPONENT
INSPECTION AND SERVICE
CAUTION
Be sure to identify each removed part as to its loca-
tion, and lay the parts out in groups designated as
“Front cylinder”,“Rear cylinder”,“Exhaust”,
“Intake”, so that each will be restored to the origi-
nal location during assembly.
◉ CYLINDER HEAD DISTORTION

Decarbonate in combustion chamber.
Check the gasket surface of the cylinder head for distor-
tion with a straightedage and thickness gauge, taking a
clearance reading at several places as indicated. If the
largest reading at any position of the straightedge
exceeds the limit, replace the cylinder head.
Cylinder head Service limit
distortion 0.05 mm (0.002 in)
◉ VALVE FACE WEAR

Visually inspect each valve face for wear. Replace any
valve with an abnormally worn face. The thickness of
the valve face decreases as the face wears. Measure
the valve head thickness �. If it is out of specification,
replace the valve with a new one.
Valve head thickness �

Service limit �
0.5 mm (0.02 in)
Vernier calipers : 09900-20101
◉ VALVE STEM RUNOUT

Check the valve stem for abnormal wear or bend.
Place the valve on V-blocks and measure runout.
If the service limit is exceeded or abnormal condi-
tion exists, replace the valve.
Service limit
Valve stem runout
0.05 mm (0.002 in)
Dial gauge : 09900-20606

Magnetic stand : 09900-20701
V-block : 09900-21304
ENGINE 3-22
◉ CAMSHAFT (T.D.C)
The camshaft should be checked for runout and also for (B.T.D.C) (A.T.D.C)
wear of cams and journals if the engine has been noted Intake open Exhaust close
to produce abnormal noise or vibration or a lack of out-
put power. Any of these abnormality could be caused by
a worn camshaft.
(A.B.D.C)
Intake close
(B.B.D.C)
Exhaust
open
(B.D.C)
Valve timing diagram
▣ CAMSHAFT WEAR
Worn-down cams are often the cause of mistimed valve
operation resulting in reduced output power.
The limit of cam wear is specified for both intake and
exhaust cams in terms of cam height �, which is to be
measured with a micrometer. Replace camshafts if
found it worn down to the limit. �
Cam height � Service limit
Intake cam 34.98 mm (1.377 in)
Exhaust cam 33.08 mm (1.302 in)
Micrometer((25~50 mm)) : 09900-20202
▣ CAMSHAFT JOURNAL WEAR

Determine whether or not each journal is worn down to
the limit by measuring the oil clearance with the
camshaft installed in place.
● Use the plastigauge to read the clearance at the
widest portion, which is specified as follows :
Camshaft journal Service limit
oil clearance
0.15 mm (0.006 in)
(IN & EX)
◉ TAPPET & SHIM WEAR

When measuring the valve clearance, the clearance
should be within the standard range.
Valve clearance Standard (When cold)

0.1 ~ 0.2 mm
Intake valve
(0.004 ~ 0.008 in)
0.28 ~ 0.32 mm
Exhaust valve
(0.011 ~ 0.013 in)
3-23 ENGINE
● Inspect the tappet for wear and scratch.

If modification or scratch is present, replace the tap-
pet.
● When you checked the valve clearance, if the valve
clearance is wide please replace the present shim
into thick one, if the valve clearance is narrow please
replace the present shim into thin shim.
(Refer to page 8-31∙32)
▣ SHIM KIND
There are 41 kinds of shim which thickness is increased
by each 0.025 mm from 1.20 mm to 2.20 mm.
◉ VALVE HEAD RADIAL RUNOUT

Place a dial gauge as shown and measure valve
head radial runout.
If the service limit is exceeded, replace the valve.
Valve head radial Service limit

runout 0.03 mm (0.0012 in)
Dial gauge : 09900-20606
V-block : 09900-21304
◉ VALVE GUIDE-VALVE STEM
CLEARANCE
Measure the clearance in the valve guide-valve stem, by
rigging up the dial gauge as shown. If the clearance
is measured exceeds the limit specified below, then
determine whether the valve or the guide should be
replaced to reduce the clearance to within the standard
range :
Valve guide-valve stem clearance Standard
0.020~0.047 mm
IN.
(0.0008~0.0019 in)
0.030~0.057 mm
EX.
(0.0012~0.0022 in)
Dial gauge : 09900-20606
◉ VALVE STEM DIAMETER
Measure the valve stem outside diameter.
If the diameter measured exceeds the standard, replace
the valve.
Valve stem diameter Standard
IN. 4.465~4.480 mm (0.1758~0.1764 in)

EX. 4.455~4.470 mm (0.1754~0.1760 in)
Micrometer(0~25 mm) : 09900-20201

ENGINE 3-24
◉ VALVE SPRING
The force of the coil spring keeps the valve seat tight. A
weakened spring results in reduced engine power out-
put and often accounts for the chattering noise coming
from the valve mechanism.
Check the valve springs for proper strength by measur
ing their free length and also by the force required
to compress them. If the spring length is less than the
service limit or if the force required to compress the
spring does not fall within the specified range, replace
both the inner and outer springs as a set.
Valve spring free length Service limit
Inner 36.8 mm (1.45 in)
Outer 39.8 mm (1.57 in)
Venier calipers : 09900-20101

Valve spring tension Standard
4.2~4.8 kgf
Inner (9.3~10.6 lbs)
at length 29.9 mm (1.18 in)
17.0~19.6 kgf
Outer (37.5~43.2 lbs)
at length 33.4 mm (1.32 in)
◉ CYLINDER DISTORTION
Check the gasketed surface of the cylinder for distor-
tion with a straightedge and thickness gauge, taking a
clearance reading at several places as indicated.
If the largest reading at any position of the
straightedge exceeds the limit, replace the cylin-
der.
Service limit
Cylinder distortion
0.05 mm (0.002 in)
◉ CYLINDER BORE
Measure the cylinder bore diameter at six place. If any
one of the measurements exceeds the limit, overhaul
the cylinder and replace the piston with an oversize, or
replace the cylinder.
Standard Service limit
Cylinder bore 81.500~81.515 mm 81.575 mm
(3.2087~3.2093 in) (3.2116 in)
Cylinder gauge set : 09900-20508
3-25 ENGINE
◉ CAM CHAIN TENSIONER

ADJUSTER
Check that the push rod slides smoothly with the lock
shaft handle ① clockwise.
If it does not slide smoothly, replace the cam chain
tensioner adjuster with a new one. ①
◉ CAM CHAIN TENSIONER

Check the contacting surface of the cam chain tensioner.
If it is worn or damaged, replace it with a new one.
◉ CAM CHAIN AND CAM CHAIN

GUIDE
Check the cam chain for wear, damage and kinked or bind-
ing links. If any defects are found, replace it with a new
one.
Check the cam chain guide for wear and damage. If it
is found to be damaged, replace it with a new one.
◉ PISTON DIAMETER INSPECTION

Measure the outside diameter of piston in the direction per-
pendicular to the piston pin axis at the height from the skirt
as shown in the illustration using a micrometer.
If the measurement is found less than the service
limit, replace the piston.
Service limit
Piston diameter 81.380 mm
20mm (0.79in)
(3.2039 in)
Piston oversize 0.5, 1.0 mm (0.02, 0.04 in)
Micrometer(75~100 mm) : 09900-20204
ENGINE 3-26
◉ PISTON-TO-CYLINDER
CLEARANCE
To determine the piston-to-cylinder clearance, calculate
the difference between the cylinder bore and outside
diameter of the piston.
Piston-to-cylin-
0.045~0.075 mm 0.120 mm
der clearance
(0.0018~0.0030 in) (0.0047 in)
◉ PISTON PIN HOLE BORE

Using a dial calipers, measure the piston pin hole bore
both the vertical and horizontal directions.
If the measurement exceeds the service limit, replace
the piston.
Service limit
Piston pin hole bore
20.030 mm (0.7886 in)
Dial calipers : 09900-20605
◉ PISTON PIN DIAMETER

INSPECTION
Using a micrometer, measure the piston pin outside
diameter at three position, both the ends and the center.
If any of the measurements is founds less than the ser-
vice limit, replace the pin.
Service limit
Piston pin diameter
19.980 mm (0.7866 in)
Micrometer(0~25 mm) : 09900-20201
◉ PISTON RING FREE END GAP

INSPECTION
Before installing piston rings, measure the free end gap
of each ring using vernier calipers. If the gap is less than
the service limit, replace the ring.
Piston ring free end gap Standard
1st Approx 9.9 mm (0.390 in)
2nd Approx 10.5 mm (0.413 in)
Piston ring free end gap Service limit

1st 7.9 mm (0.311 in)
2nd 8.4 mm (0.330 in)

3-27 ENGINE
◉ PISTON RING END GAP INSPECTION

Insert the piston ring squarely into the cylinder using
the piston head.
Measure the end gap with a thickness gauge.
If the gap exceeds the service limit, replace the piston ring.
Piston ring end gap
Standard
(Assembly condition)
0.20~0.35 mm
1st
(0.008~0.013 in)
0.20~0.35 mm
2nd
(0.008~0.013 in)
Piston ring end gap(Assembly condition) Service limit

1st 0.5 mm (0.020 in)
2nd 0.7 mm (0.028 in)
◉ PISTON RING-TO-GROOVE
CLEARANCE INSPECTION
Remove carbon deposit both from the piston ring and its
groove.
Fit the piston ring into the groove. With the ring com-
pressed and lifted up, measure the clearance on the
bottom side of the ring using a thickness gauge.
Piston ring-groove clearance Service limit
1st 0.180 mm (0.007 in)
2nd 0.150 mm (0.006 in)
Piston ring-groove width Standard

1.21~1.23 mm
1st
(0.0476~0.0484 in)
1.01~1.03 mm
2nd
(0.040~0.041 in)
2.01~2.03 mm
Oil
(0.079~0.080 in)
Piston ring thickness Standard

0.970~0.990 mm
1st
(0.0382~0.0390 in)
1.170~1.190 mm
2nd
(0.0461~0.0469 in)
Micrometer(0~25 mm) : 09900-20201

ENGINE 3-28
◉ OVERSIZE RINGS
▣ Oversize piston ring
The following two types of oversize piston ring are used.
They bear the following identification numbers.
Oversize piston ring 1st 2nd
0.5 mm 05 05
1.0 mm 10 10
▣ Oversize oil ring

The following two types of oversize oil ring are used.
They bear the following identification marks.
Oversize oil ring Color classification
0.5 mm Painted red
1.0 mm Painted yellow
◉ CONROD SMALL END INSIDE

DIAMETER INSPECTION
Using a dial calipers, measure the conrod small end
inside diameter both in vertical and horizontal directions.
If any of the measurements exceeds the service
limit, replace the conrod.
Conrod small
20.006~20.014 mm 20.040 mm
end I.D.
(0.7876~0.7880 in) (0.7890 in)
Dial calipers : 09900-20605
◉ CONROD DEFLECTION INSPEC-

TION
Move the small end sideways while holding the big end
immovable in thrust direction.
Measure the amount of deflection.
Turn the conrod and see if it moves smoothly without
play and noise. This method can check the extent of
wear on the parts of the conrod’s big end.
Service limit
Conrod deflection
3.0mm (0.12 in)
Dial gauge : 09900-20606
V-block : 09900-21304
3-29 ENGINE
◉ CONROD BIG END SIDE

CLEARANCE INSPECTION
Using a thickness gauge, measure the side clearance at
the conrod big end. If the measurement is out of stan-
dard value, measure the conrod big end and the crank
pin widths individually to determine which one is to be
replaced.
Conrod big end
0.17~0.32 mm 0.50 mm
side clearance
(0.007~0.013 in) (0.020 in)
◉ CRANKSHAFT RUNOUT
INSPECTION
With the right and left crank journals supported with V-
block, turn the crankshaft slowly. At this time, measure
the crankshaft end runout using a dial gauge. If the
runout exceeds the service limit, replace the crankshaft.
Service limit
Crankshaft runout
0.05 mm (0.002 in)
Dial gauge : 09900-20606

V-block : 09900-21304
◉ CRANKSHAFT REASSEBLY
Measure the width between the webs referring to the fi-
gure below when rebuilding the crankshaft.
Standard
Width between webs 96.9~97.1 mm
(3.815~3.823 in)
96.9~97.1mm
◉ MAGNETO COVER
▣ MAGNETO INSPECTION (Refer to page 6-4) ①
▣ DISASSEMBLY
● Remove the stator ①.
ENGINE 3-30
◉ STARTER CLUTCH
Install the starter driven gear onto the starter clutch and
turn the starter driven gear by hand(the gear turns in
only one direction). The starter driven gear should turn
smoothly. If excessive resistance is felt while turning the
starter driven gear, inspect the starter clutch. Also,
inspect the surface of the starter driven gear which con-
tacts the starter clutch, for wear or damage. If any wear
or damage is found, replace the defective parts.
▣ DISASSEMBLY
● With the magneto rotor held immovable, remove the
starter clutch bolts.
▣ REASSEMBLY
● Apply a small quantity of THREAD LOCK“1324”to
the starter clutch bolts and tighten them to the spec-
ified torque with the magneto rotor held immovable.
Thread Lock“1324”
Starter clutch bolt
: 23~28 N∙m (2.3~2.8 kg∙m)
◉ STARTER DRIVEN GEAR ②

▣ STARTER DRIVEN GEAR BUSH
Install the starter driven gear bush ① and gear ② onto
the crankshaft and turn the starter driven gear by hand.
Inspect the starter driven gear bush for smooth rotation
and any abnormal noise. If the bush does not turn
smoothly or there is any abnormal noise, replace it.
①
3-31 ENGINE
◉ DISASSEMBLY
● Remove the bush using the special tool.
Bearing remover (20~35 mm)

: 09923-74510
◉ OIL JET ①
▣ REMOVAL
● Remove the oil jet ①, ② from the right crankcase
half.
● Remove the oil jet ③ from the left crankcase half.
NOTE
If it is difficult to remove the oil jet, use a sting.
③
ENGINE 3-32
▣ INSPECTION AND CLEANING

● Check the oil jets for clogging.
● If they are clogged, clean their oil passage with a
proper wire and compressed air.
▣ INSTALLATION
● Fit the new O-ring to each oil jets.
CAUTION
Use the new O-ring to prevent oil leakage.
● Apply engine oil to the O-ring.
● Install the oil jet ① to the oil hole of crankcase.
NOTE
Push the oil jet the crankcase until it stops.
◉ CLUTCH COVER
▣ OIL FILTER REPLACEMENT
▣ DISASSEMBLY
● Remove the circlip and right crankshaft oil seal.
Oil seal remover : 09913-50121
3-33 ENGINE
▣ REASSEMBLY
● Drive in the oil seal using the special tool.
Bearing installer : 09913-75820
● Install the circlip.
◉ CLUTCH DRIVE PLATES

Measure the thickness and claw width of the clutch drive
plates using vernier calipers. If a clutch drive plate is not
within the service limit, replace the clutch plates as a
set.
Standard
Clutch drive plate
NO.1 2.92~3.08 mm (0.115~0.121 in)
thickness
NO.2 3.42~3.58 mm (0.135~0.141 in)
Service limit
Clutch drive plate
NO.1 2.62 mm (0.103 in)
thickness
NO.2 3.12 mm (0.123 in)
Standard
Clutch drive plate
NO.1 15.9~16.0 mm (0.626~0.630 in)
claw width
NO.2 15.9~16.0 mm (0.626~0.630 in)
Service limit
Clutch drive plate
NO.1 15.1 mm (0.595 in)
claw width
NO.2 15.1 mm (0.595 in)
◉ CLUTCH DRIVEN PLATES

Measure each clutch driven plate for distortion using
the thickness gauge. If a clutch driven plate is not within
the service limit, replace the clutch plates as a set.
Clutch driven plate Service limit

distortion 0.1 mm (0.004 in)

ENGINE 3-34
◉ CLUTCH SPRING FREE LENGTH

Measure the free length of each clutch spring using
vernier calipers. If any spring is not within the service
limit, replace all of the spring.
Clutch spring Service limit

free length 51 mm (2.008 in)
◉ CLUTCH RELEASE BEARING

Inspect the clutch release bearing for any abnormality,
especially cracks. When removing the bearing from the
clutch, decide whether it can be reused or if it should be
replaced.
Smooth engagement and disengagement of the clutch
depends on the condition of this bearing.
◉ PRIMARY DRIVEN GEAR

Inspect the primary driven gear bearing for any damage.
If any abnormal condition are found, replace the primary
driven gear.
◉ OIL PUMP
Turn the oil pump shaft and check that rotation is
smooth. If any abnormal condition is found, replace the
oil pump with new one.
3-35 ENGINE
◉ GEARSHIFT SHAFT
Disassemble and reassemble the gearshift shaft as
shown in right picture.
◉ TRANSMISSION
▣ INSPECTION
◈ GEAR-SHIFTING FORK
Using a thickness gauge, check the clearance between
the groove of its gear and shifting fork.
The clearance for each of the three shifting forks plays
an important role in the smoothness and positiveness of
shifting action.
If the clearance checked is noted to exceed the limit
specified, replace the fork or its gear, or both.
Shift fork-groove
0.10~0.30 mm 0.50 mm
clearance
(0.004~0.012 in) (0.020 in)
Shift fork groove width Standard

4.85~5.00 mm
NO.1 & NO.2
(0.191~0.197 in)
4.85~5.00 mm
NO.3
(0.191~0.197 in)
Shift fork thickness Standard

5.3~5.4 mm
NO.1 & NO.2
(0.209~0.213 in)
5.3~5.4 mm
NO.3
(0.209~0.213 in)
▣ REASSEMBLY
Assemble the countershaft and drive shaft in the reverse
order of disassembly. Pay attention to following points :
NOTE
Before installing the gears, coat lightly engine oil
to the driveshaft and countershaft.
ENGINE 3-36
CAUTION
� Never reuse a circlip. After a circlip has been
removed from a shaft, it should be discarded
Thrust
and a new circlip must be installed.
� When installing a new circlip, care must be
taken not to expand the end gap larger than
required to slip the circlip over the shaft.
� After installing a circlip, always ensure that it
is completely seated in its groove and securely
fitted.
● When installing a new circlip, pay attention to the

direction of the circlip. Fit it to the side where the
thrust is as shown in figure.
▣ TRANSMISSION GEARS AND RELATED PARTS
Thickness for washers, circlips and

spacers � � �
� 1.0mm
� 1.2mm
� 1.5mm
� � � � � �
3-37 ENGINE
◉ CRANKCASE play
play
▣ BEARING INSPECTION
Rotate the bearing inner race by finger to inspect for
abnormal play, noise and smooth rotation while the
bearings are in the crankcase.
Replace the bearing in the following procedure if there is
anything unusual.
▣ DISASSEMBLY
◈ RIGHT CRANKCASE BEARING ①
● Remove the bearing retainer bolt ①, ②, and ③.
● Remove the bearing retainer.
● Remove the bearings ④, ⑤ and ⑥.

Bearing remover (17 mm) : 09923-73210 ④
Bearing remover (20~35 mm)
: 09923-74510 ⑤
⑥
ENGINE 3-38
● Remove the bearing ①.

①
CAUTION
The removed bearing should be replaced with a
new one.
◈ LEFT CRANKCASE BEARING

● Remove the oil seals ② and ③.
● Remove the bearings ④, ⑤, and ⑥.

④
Bearing remover (17 mm) : 09923-73210
Bearing remover (20~35 mm) : 09923-74510 ⑤
▣ REASSEMBLY ⑧ ⑨
◈ RIGHT CRANKCASE BEARING ⑦
● Drive in the bearings ⑦, ⑧, ⑨ and ⑩.
⑩
3-39 ENGINE
◈ LEFT CRANKCASE BEARING

● Drive in the bearings ①, ② and ③.
③
②
①
● Install the oil seals ④ and ⑤.

● Apply SUPER GREASE“A”on the lip of oil seal.
SUPER GREASE“A”
④ ⑤
ENGINE REASSEMBLY
The engine reassembly can be performed in the reverse
order of disassembly procedures. However, the follow-
ing points must be observed in the reassembly opera-
tion.
CAUTION
Make sure to coat the rotating and sliding sec-
tions with engine oil.
◉ CRANKSHAFT
● Using the special tool, press the crankshaft into the
left crankcase.
Crankshaft installer : 09910-32812
Crankshaft installer adapter
: 09910-32813
CAUTION
Never fit the crankshaft into crankcase by strik-
ing it with a plastic hammer.
Always use the special tool, otherwise crankshaft
alignment accuracy will be affected.
ENGINE 3-40
◉ TRANSMISSION
● Install the transmission.
◉ GEARSHIFT CAM AND

GEARSHIFT FORKS
● Install the gearshift fork NO.1 ①, NO.2 ②, and NO.3
③.
③
②
①
③
②
● Install the gearshift cam ④, and gearshift fork shaft

⑤, ⑥.
⑥
⑤
● Install the dowel pins ⑦.

● Before assembling the crankcase, apply the engine ⑦
oil to each gear and bearing.
⑦
3-41 ENGINE
● Apply BOND“1215”to the right crankcase.

BOND“1215”
CAUTION
� Application of BOND“1215”must be per-
formed within a short period of time.
� Take extreme care not to let BOND“1215”
enter into the oil hole or bearing.
● Install the crankcase.

● Install the crankcase bolts, right and left.
Crankcase bolt (M6)
: 11 N∙m (1.1 kg∙m)
Crankcase bolt (M8)
: 26 N∙m (2.6 kg∙m)
NOTE
Tightening the crankcase bolts, tighten each bolt
little by little diagonally.
NOTE
� After the crankcase bolts have been tight-
ened, make sure that the crankshaft, counter-
shaft and driveshaft rotate smoothly.
� If these shafts do not rotate smoothly, try to
free it by tapping with a plastic hammer.
ENGINE 3-42
● Apply the SUPER GREASE“A”to the driveshaft O-

ring and oil seal lip.
SUPER GREASE“A”
● Install the driveshaft spacer.
● Install the oil seal retainer.
▣ GEARSHIFT CAM STOPPER

● Apply a small quantity THREAD LOCK“1324”to the
gearshift cam plate bolt ①. ①
THREAD LOCK“1324”
● Install the gearshift cam stopper plate and gearshift ②
cam plate bolt ①.
● Install the gearshift cam stopper ②.
▣ GEARSHIFT SHAFT
● Install the gearshift shaft ③.
③
3-43 ENGINE
CAUTION
After the cam driven gear, cam guide, gearshift 5th
shaft and neutral cam stopper have been fitted,
confirm that gear change is normal while turning 4th
the countshaft and driveshaft. If gear change is
not obtained, it means that assembly of gears or 3rd
installation of gear shifting fork is incorrect. In
2nd
this case, disassemble and trace the mistake.
N
1st
◉ OIL PUMP
● Before installing the oil pump, apply the engine oil to
the contact face of case, outer rotor, inner rotor and
shaft.
● Apply a small quantity THREAD LOCK“1324”to the
oil pump securing screws.
● Tighten the oil pump securing screws.
● Install the oil pump shim and pin.
● Put in the oil pump driven gear, and install the circlip.
CAUTION
When installing the oil pump to the crankcase,
turn the pump gear and check that rotation is
smooth by the hand.
ENGINE 3-44
◉ CAM CHAIN TENSIONER ① ②

● Install the washer and cam chain tensioner ②,
tighten the cam chain tensioner bolt ①.
Cam chain tensioner bolt ③
: 8~12 N∙m (0.8~1.2 kg∙m)
● Install the cam chain ③.
◉ PRIMARY DRIVE GEAR Align the key groove

● Install the primary drive gear and NO.2 gear to the and mark.
crankshaft, put the key to the key groove.
CAUTION
When installing the NO.2 gear, install so that the
mark on the gear align the key groove as shown
in figure.
NO.2 Gear
CAUTION
Pay attention to the each washer to lower end of
the water pump drive gear and primary drive gear
nut in times of assemblage.
● With the crankshaft held immovable using special

tool, install the water pump drive gear ④ and primary
drive gear nut ⑤. ④
Primary drive gear nut
: 40~60 N∙m (4.0~6.0 kg∙m)
NOTE
The primary drive gear nut has left-hand thread.
⑤
3-45 ENGINE
◉ PRIMARY DRIVEN GEAR

NOTE
Apply the engine oil to the inside face of primary
driven gear bearing.
● Install the primary driven gear assembly.
◉ CLUTCH ②
● Install the clutch sleeve hub ①, lock washer ②.
● Install the clutch sleeve hub nut, and tighten it to the

specified torque using the special tool.
Clutch sleeve hub holder : 09920-53710
Clutch sleeve hub nut

: 40~60 N∙m (4.0~6.0 kg∙m)
● Bend the lock washer securely.
● Install the clutch drive plate NO. 2 �.

● Install the spring washer seat � and spring washer � �
� onto the clutch sleeve hub correctly.
● Install the clutch driven plates � and drive plates
NO. 1 � one by one into the clutch sleeve hub in the
prescribed order.
ENGINE 3-46
� �
Direction
of inside
�
� NO. 2 Drive plate � NO. 1 Drive plate
● Install the clutch release rack ①, bearing ② and

washer ③.
③ ② ①
● Install the clutch pressure plate ④, retainer, clutch

springs and clutch spring mounting bolts. ④
● Hold the primary drive gear nut and tighten the clutch
spring mounting bolts in a crisscross pattern.
NOTE
Make sure that the clutch pressure plate is
installed correctly.
▣ CLUTCH COVER
● Install the two dowel pins ⑤ and new gasket ⑥. ⑤ ⑥
● Apply engine oil to each gears, bearings and clutch
plates.
⑤
3-47 ENGINE
● Install the clutch cover, and tighten the clutch cover

bolts securely.
● Install the clutch release arm as following :

① Turn the clutch release shaft toward(This time, Stopper screw
mark on the shaft align outside contact line the Clutch release
stopper screw) the right. arm bolt
② Install that the release camshaft notch mark align
matching mark of the crankcase as shown in the
right figure.
Crankcase
matching mark Release camshaft
notch mark
Clutch release arm
◉ OIL DRAIN PLUG

● Tighten the oil drain plug to the specified torque.
Engine oil drain plug
: 21 N∙m (2.1 kg∙m)
◉ STATOR
the threaded parts of screws.
◉ STARTER CLUTCH
● When installing the starter clutch and rotor, apply the
THREAD LOCK“1324”to the bolts and tighten to
the specified torque.
Starter clutch bolt
: 23~28 N∙m (2.3~2.8 kg∙m)
ENGINE 3-48
◉ MAGNETO ROTOR
● Fit the key into the key slot on the crankshaft.
● With the magneto rotor, install the starter clutch on
the crankshaft.
the threaded parts of crankshaft.
● Tighten the magneto rotor bolt to the specified

torque.

Magneto rotor bolt
: 110~170 N∙m (11.0~17.0 kg∙m)
◉ STARTER IDLE GEAR AND

MOTOR
● Install the starter idle gear, shaft.
● Install the starter motor.

3-49 ENGINE
◉ MAGNETO COVER
● Install the new gasket and dowel pin.
● Apply oil to the each gear, bearing and starter clutch.
● Install the magneto cover and tighten the magneto

cover bolts.
Magneto cover bolt
: 10 N∙m (1.0 kg∙m)
◉ PISTON RING
● First, install the piston ring in order of oil ring, 2nd
ring and 1st ring at the front cylinder.
CAUTION
Be careful not to cause scratch on the piston
when inserting the piston ring to the piston.
Also, do not expand the piston ring more than
necessary as the ring can break.
● When all the piston rings have been assembled,

check that each can turn smoothly.
● To minimize compression and oil leaks, locate each
piston ring end gap in the position as shown in the EX
right illustration
● Install the spacer ①. ② ②
● Install the upper and lower side rail ②.
② INCORRECT
② CORRECT
①
◉ PISTON IN
● Apply the MOLY PASTE to the piston pin.
MOLY PASTE
● When installing the piston, turn the mark � on the �
piston head to exhaust side. ③
● After the piston pin has been inserted through the
conrod, install the circlip ③.
CAUTION
Replace the circlip with a new one.
Place a piece of rag under the piston when
installing the circlip to prevent it from falling
into the crankcase.
ENGINE 3-50
◉ CYLINDER
● Apply BOND“1215”to the parting line of crankcase. ①
BOND“1215”
● Place the dowel pin ① and new gasket on the
crankcase.
CAUTION
Make sure to replace the gasket with a new one.
● Apply the engine oil to the conrod small end, piston

and the piston rings.
● Coat the cylinder wall with oil.
● Install the cylinder and tighten the cylinder base nuts.
Cylinder base nut Broad pitch part
: 7~11 N∙m (0.7~1.1 kg∙m) ↓
This cylinder is different from the front and rear.
↓
Head direction
◉ VALVE AND SPRING
● Insert the valve, with their stems coated with MOLY ↓
PASTE. ↓
MOLY PASTE Narrow pitch part
Apply the oil to the lip of the stem seal.
● The narrow pitch side of each spring face to the head
when the valve spring install. The pitch of inside
spring and outside spring is changed. The pitch of
spring is decreased from the upper side to the lower
side.
◉ CYLINDER HEAD
● Put the valve spring and retainer and install the valve
cotter with compressed the spring by using the valve
spring compressor.
Valve spring compressor : 09916-14510
: 09916-14520
CAUTION
After installing the valve cotter, tap the valve
stem end by using the plastic hammer at 2~3
times for assembly of the valve and cotter.
● Fit the cylinder head and tighten the six cylinder head
bolts diagonally.
Cylinder head bolt (M6)
: 8~12 N∙m (0.8~1.2 kg∙m)
Cylinder head bolt (M10)
: 40~45 N∙m (4.0~4.5 kg∙m)
3-51 ENGINE
CAUTION
Pay caution to prevent the cam chain from drop-
ping into the crankcase.
● Tighten the cylinder head base bolt.

Cylinder head base bolt
: 8~12 N∙m (0.8~1.2 kg∙m)
● Install the tappet and shim.
CAUTION Tappet
With the tappet fitted, it should be replaced if it
doesn’ t turn smoothly by the hand.
Shim
CAUTION
The tappet and shim should be installed at the
original position when removed.
If otherwise, it is difficult to adjust the valve clear-
ance.
● Fit the chain guide.
[ Front Cylinder ]
[ Rear Cylinder ]
ENGINE 3-52
◉ CAMSHAFT ASSEMBLY
● Distinguish the“EX”mark for the exhaust camshaft,
the“IN”mark for the intake camshaft. EX IN
IN
EX
● With pulling up the camshaft drive chain, align the“｜

F”mark of magneto rotor into the punching mark of
magneto cover to turn the crankshaft.
(Front cylinder)
CAUTION
When adjusting the rear cylinder, align the“｜R”
mark of magneto rotor into turn counter-clock-
wise 285�at the position of front cylinder.
CAUTION
If turn the crankshaft without pulling up the camshaft
drive chain, the chain may be fallen off between the
crankcase and cam chain drive sprocket.
● The front cylinder head install first the exhaust

camshaft, following the intake camshaft.
The rear cylinder head install first the intake as the
cam chain tensioner adjuster exist exhaust side.
3-53 ENGINE
● The“1F”arrow of exhaust camshaft sprocket should

be toward the outside and aligned with the plane of
FRONT cylinder head.
At that time, the“2”arrow of exhaust camshaft
sprocket should be in a vertical position to the plane 2 3
of cylinder head when exhaust camshaft sprocket
was geared into cam chain.
1F
● The“1R”arrow of intake camshaft sprocket should

be toward the outside and aligned with the plane of
REAR cylinder head. At that time, the“2”arrow of
intake camshaft sprocket should be in a vertical posi-
3 2
tion to the plane of cylinder head when the intake
camshaft sprocket was geared into the cam chain.
1R
● Gear into the chain at the“3”arrow of intake sprock- 16pin

et that count the 16th of chain roller pin from the Exhaust Intake
roller pin on the“ 2”arrow of exhaust sprocket to the
intake camshaft. 2 3
CAUTION
The REAR cylinder gear into that count the 16th
of chain roller pin from the “ 2 ” arrow of
intake sprocket to the“ 3 ”arrow of exhaust
sprocket.
● Install the“ 3”arrow punching mark of intake

camshaft sprocket with the surface of cylinder head
vertically.
ENGINE 3-54
CAUTION
The cam chain is installed to the all of three sprocket.
Be sure to lie the crankshaft until the two holder and cam chain tensioner adjuster are installed completely.
1 Link Rotation Direction 16 Link
Exhaust Intake
[Front cylinder]
Rotation Direction
16 Link 16 Pin 1 Link
Exhaust Intake
[Rear cylinder]
NOTE
The camshaft housing should be installed in the same manner with the front engine.
3-55 ENGINE
● Put the intake or exhaust camshaft housing to the

cylinder head upper surface.
● Tighten the camshaft housing bolt with the specified
torque diagonally.
CAUTION
The camshaft housing bolt is made of the special
material.
This bolt is superior at the degree of hardness
more than the different high tension bolt.
Pay special caution that the different type of bolt
should not be used.
This bolt head is punched the“ 9”mark.
Camshaft housing bolt

: 12 N∙m (1.2 kg∙m)
● If turn the lock shaft handle in clockwise ( )

direction, the pushrod is inserted in.
�
Turn the mechanical spring continually until the han-
dle is turned to the end.
Lock shaft handle
● Fix the adjuster into the cylinder block.
● Get out the pushrod for the front to turn the lock shaft
handle in counter-clockwise ( ).
ENGINE 3-56
● Turn the crankshaft about 10 times counter-clock-

wise ( ) on the basis of the magneto rotor.
● If the valve clearance is within standard after mea-
sured the valve clearance, begin the next operation.
If it is out of stanadard, adjust the valve clearance
within standard limit after disassembled the camshaft
and replaced the proper shim.
Valve clearance Standard

0.1 ~ 0.2 mm
IN.
(0.004 ~ 0.008 in)
0.28 ~ 0.32 mm
EX.
(0.011 ~ 0.013 in)
● Adjust the valve clearance of rear cylinder with the

same manner of the front cylinder.
(Refer to page 2-4)
CAUTION
’
If you don’t turn the crankshaft about 10 times
before measured the valve clearance, there is no
meaning in valve clearance.
● Apply BOND“1215”to the surface of cylinder head

cover packing block.
BOND“1215”
● Tighten the cylinder head cover bolts with the speci-

fied torque.
Cylinder head cover bolt
: 12~16 N∙m (1.2~1.6 kg∙m)
◉ SPARK PLUG
● Install the spark plug. (Refer to page 2-7)
3-57 ENGINE
● Install the rear cylinder head and cylinder with the Rear Cylinder
same manner which installed the front cylinder head
and cylinder.
Front Cylinder
◉ THERMOSTAT
● Install the thermostat case ① along with the hose ②. ①
NOTE
Thermostat reassembly
: Refer to page 5-9
◉ GEAR POSITION SWITCH

● Install the spring ③ and contact ④.
● Apply SUPER GREASE“A”to the O-ring and install ③
the gear position switch.
SUPER GREASE“A”
④
FUEL SYSTEM
CONTENTS
FUEL TANK / FUEL COCK …………………………………………… 4- 1

FUEL PUMP ………………………………………………………………… 4- 2
CARBURETOR ……………………………………………………………… 4- 3
CAUTION
Gasoline must be handled carefully in an area well ventilated and away from fire or sparks.
4-1 FUEL SYSTEM
FUEL TANK / FUEL COCK

◉ REMOVAL
WARNING
Gasoline is very explosive. Extreme care must be
taken.

● Remove the fuel tank mounting bolts and fuel tank
bracket mounting bolt.
● Disconnect the fuel hose ① and remove the fuel
tank.
● Remove the fuel cock.
◉ INSPECTION
▣ FUEL COCK
If the fuel filter is dirty with sediment or rust, fuel will not
flow smoothly and loss of engine power may result.
Clean the fuel filter.
Also check the fuel cock for cracks.
FUEL SYSTEM 4-2
◉ REMOUNTING
Remount the fuel tank and fuel cock in the reverse order ①
of removal.
CAUTION
● Gaskets ① and ② must be replaced with new
ones to prevent fuel leakage.
● Tighten the fuel cock bolts evenly.
②
FUEL PUMP
⑤
◉ REMOVAL
● Remove the seat and fuel tank.
● Disconnect the fuel hoses ③, ④ and vacuum hose
⑤.
● Remove the fuel pump mounting bolts.
④
③
◉ INSPECTION
WARNING
Gasolin is very explosive. Extreme care must be
taken.
● Disconnect the fuel hose ③, connect the suitable

hose and insert the free end of the hose into a recep-
tacle.
Check the fuel flow when starting the engine for a few
seconds by pressing the starter switch. ③
If the fuel flow is not found, check the fuel cock. (Refer
to page 4-1)
If the fuel cock and hoses are not fault, replace the fuel
pump.
◉ REASSEMBLY
Carry out the assembly procedure in the reverse order ⑤
of disassembly.
● Tighten the fuel pump mounting bolts.
● Connect the fuel hoses ③, ④ and vacuum hose ⑤
securely. ③
FUEL HOSE ROUTING :
Fuel hose ③ (To carburetor)
Fuel hose ④ (To fuel cock)
Vacuum hose ⑤ (To carburetor vacuum pipe).
④
4-3 FUEL SYSTEM
CARBURETOR
FUEL SYSTEM 4-4
◉ LOCATION OF CARBURE-
TOR I.D.NO.
The carburetor I.D. is stamped on the location on the
carburetor as shown in the right photo.
◉ REMOVAL
● Remove the fuel hose.
● Remove the throttle cables ① and choke cable.

● Loosen the clamp screw and remove the carburetor.
①
◉ DISASSEMBLY
● Remove the diaphragm cover ②.
②
4-5 FUEL SYSTEM
● Remove the spring ① along with diaphragm ②.

②
● Remove the jet needle cap ③, spring ④, retainer

⑤, and jet needle ⑥.
③ ④⑤ ⑥
● Remove the float chamber body ⑦.
● Remove the float assembly ⑨ along with the needle

valve ⑧ by removing the pin.
⑧
⑨
FUEL SYSTEM 4-6
● Remove the valve seat ①.

● Remove the main jet ②, jet holder ③ and pilot jet ④.
② ④
③
①
● Remove the pilot screw ⑤ counting and tightening

the number of turn.
NOTE
Record the number of turn for the pilot screw
when install to confer.
⑤
◉ INSPECTION
Check the following parts for damage and clogging.
∙Pilot jet ∙Piston valve
Check for
∙Main jet ∙Starter jet stopped
∙Main air jet ∙Gaskets and O-rings wear
∙Pilot air jet ∙Pilot outlet and bypass
∙Needle jet holder ∙Float
∙Needle valve ∙Jet needle Foreign
∙Valve seat substance
If any abnormal condition is found, wash the part clean.

If damage or clogging is found, replace the part with a
new one. Needle valve
◉ CLEANING
● Clean all jets by using compressed air.
● After cleaning, reassemble the carburetor with new
seals and gaskets.
4-7 FUEL SYSTEM
◉ FLOAT HEIGHT ADJUSTMENT

To check the float height, turn the carburetor upside
down. Measure the float height � while the float arm is
just contacting the needle valve using vernier calipers. �
Float height � 7 mm (0.28 in)
● Bend the float arm ① as necessary to bring the

height to the specified level. ①
● After adjustment, check the float height and the fuel
level again.
◉ REASSEMBLY
Carburetor reassembly can be performed in the reverse
order of disassembly. When reassembling, carefully
observe the following instructions.
● After cleaning, reinstall the pilot screw to the original

number of turn that is recorded during disassem-
bly.
● Fit the seal rings securely to the float chamber and

install the float chamber to the carburetor body.
● Install the three screws ②. ②
FUEL SYSTEM 4-8
● Align the hole ① of the diaphragm with passage way

on the carburetor body.
● Install the two screws ② and diaphragm cover ③.
③ ②
CAUTION
Never adjust“CO adjust screw”� of the carbure-
tor. If adjust at discretion, have a bad influence
upon output of the engine as the two carburetor
is disharmonious.
�
● After the assembly and installation on the

engine have been completed, perform the follow-
ing adjusment.
Throttle cable adjustment. (Refer to page 2-9)
Idle speed adjustment. (Refer to page 2-9)
COOLING SYSTEM
CONTENTS
ENGINE COOLANT ……………………………………………………… 5- 1

COOLING CIRCUIT ……………………………………………………… 5- 2
RADIATOR …………………………………………………………………… 5- 2
COOLING FAN ……………………………………………………………… 5- 5
COOLING FAN THERMO-SWITCH ………………………………… 5- 6
ENGINE COOLANT TEMPERATURE SENSOR ………………… 5- 7
THERMOSTAT ……………………………………………………………… 5- 8
WATER PUMP ……………………………………………………………… 5-10
5
5-1 COOLING SYSTEM
ENGINE COOLANT Anti-freeze density Freezing point

At the time of manufacture, the cooling system is filled 50% -31℃ (-24℉)
with a 50 : 50 mixture of distilled water and ethylene gly- 55% -40℃ (-40℉)
col anti-freeze.
This 50 : 50 mixture will provide the optimum corrosion 60% -55℃ (-67℉)
protection and excellent heat protection, and will protect
the cooling system from freezing at temperatures above
-31℃ (-24℉)
If the motorcycle is to be exposed to temperatures
below -31 ℃ (-24 ℉ ), this mixing ratio should be
increased up to 55% or 60% according to the figure.
Freezing point
CAUTION
● Use a high quality ethylene glycol base anti-
freeze, mixed with distilled water. Do not mix
an alcohol base anti-freeze and different
brands of anti-freeze.
● Do not rut in more than 60% anti-freeze or less
than 50%. (Refer to Right figure.) Density (%)
● Do not use a radiator anti-leak additive. Fig.1 Engine coolant density-freezing
point curve.
50% Engine coolant including reserve tank capacity
Anti-freeze 0.8ℓ
(kgf/㎠)
Water 0.8ℓ
Gauge pressure
Boiling point
Density (%)
Fig.2 Engine coolant density-boiling
point curve.
WARNING
● You can be injured by scalding fluid or steam if you open the radiator cap when the engine is hot. After the
engine cools, wrap a thick cloth around cap and carefully remove the cap by turning it a quarter turn to
allow pressure to escape and then turn the cap all the way off.
● The engine must be cool before servicing the cooling system.
● Coolant is harmful;
� If it comes in contact with skin or eyes, flush with water.
� If swallowed accidentally, induce vomiting and call physician immediately.
� Keep it away from children.
COOLING SYSTEM 5-2
COOLING CIRCUIT
RESERVE TANK
RADIATOR
FRONT CYLINDER HEAD

FRONT CYLINDER
THERMOSTAT WATER PUMP
REAR CYLINDER
REAR CYLINDER HEAD
RADIATOR
◉ REMOVAL
● With the two mounting bolts ② removed, remove the ①
right front side cover ①.
● Remove the radiator cap bolt ③.
②
③
● Remove the radiator cover by the four mounting

bolts.
● Disconnect the radiator outlet hose ④.
④
5-3 COOLING SYSTEM

coupler ①.
● Disconnect the radiator inlet hose ②.
● Disconnect reserve tank hose ③.

● Disconnect the cooling fan motor lead wire coupler
④
④.
③
● Remove the radiator by the mounting bolts.
◉ INSPECTION AND CLEANING

Road dirt or trash stuck to the fins must be removed.
Use of compressed air is recommended for this clean-
ing.
COOLING SYSTEM 5-4
Fins bent down or dented can be repaired by straighten-

ing them with the blade of a small screwdriver.
◉ INSPECTION OF WATER
HOSE
Any water hose found in a cracked condition or flattened
or water leaked must be replaced.
Any leakage from the connecting section should be cor-
rected by proper tightening.
◉ INSTALLATION
The radiator reassembly can be performed in the
reverse order of disassembly procedures.
However, the following points must be observed in the
reassembly operation.
● Install the radiator with the specified torque.
Radiator mounting bolt
: 8~12 N∙∙m (0.8~1.2 kg∙
∙m)
� Pour engine coolant Refer to page 2-24
� Bleed air from the cooling circuit Refer to page 2-25
5-5 COOLING SYSTEM
COOLING FAN ①
◉ INSPECTION
● Remove the radiator cover. (Refer to page 5-2)
● Disconnect the cooling fan motor lead wire coupler ①
and its thermo-switch lead wire coupler ②.
Test the cooling fan motor for load current with an
ammeter connected as shown in the illustration.
The voltmeter is for making sure that the battery

applies 12 volts to the motor. With the motor with
B
electric motor fan running at full speed, the amme-
ter should be indicating not more than 5 amperes. BrW
If the fan motor does not turn, replace the motor Fan motor Ammeter
assembly with a new one.
Battery
NOTE
When making above test, it is not necessary to
remove the cooling fan.
◉ REMOVAL
● Drain engine coolant. (Refer to page 2-24) ③
● Remove the radiator cover.
● Remove the radiator. (Refer to page 5-2)
● Disconnect the cooling fan thermo-switch ③.
● Remove the cooling fan.
◉ INSTALLATION
● Install the cooling fan to the radiator.
Cooling fan mounting bolt
: 8~12 N∙∙m (0.8~1.2 kg∙ ∙m)
Cooling fan motor mounting bolt
: 8 N∙ ∙m (0.8 kg∙
∙m)
● Install the radiator.
● Route the radiator hoses properly.
● Pour engine coolant. (Refer to page 2-24)
● Bleed air from the cooling circuit.
● Install the radiator cover.
COOLING SYSTEM 5-6
COOLING FAN THERMO-

SWITCH
◉ REMOVAL
● Remove the radiator cover. (Refer to page 5-2)
coupler ①.
● Remove the cooling fan thermo-switch ②. ② ①
◉ INSPECTION
● Check the thermo-switch closing or opening tempera-
④
tures by testing it at the bench as shown in the figure. ③
Connect the thermo-switch ③ to a circuit tester and
place it in the OIL contained in a pan, which is placed
on a stove.
● Heat the oil to raise its temperature slowly and read
the column thermometer ④ when the switch closes
Cooling fan thermo-switch

Standard Oil
operating temperature
℃
Over 88℃
ON → OFF
℉)
(190℉
℃
Approx. 95℃
OFF → ON
℉)
(203℉
Multi circuit tester set : 09900-25008
CAUTION
● Take special care when handling the thermo-
switch.
It may cause damage if it gets a sharp impact.
● Do not contact the cooling fan thermo-switch
③ and the column thermometer ④ with a pan.
⑤
◉ INSTALLATION
● Install a new O-ring ⑤ and apply engine coolant to
the O-ring.
● Tighten the cooling fan thermo-switch to the specified
torque.
Cooling fan thermo-switch
: 13 N∙ ∙m (1.3 kg∙ ∙m)
● Bleed air from the cooling circuit. (Refer to page 2-25)
● Install the radiator cover.
5-7 COOLING SYSTEM
ENGINE COOLANT TEM- ①

PERATURE SENSOR
◉ REMOVAL
● Remove the carburetor. (Refer to page 4-4)
● Disconnect the engine coolant temperature sensor
lead wire coupler.
● Place a rag under the sensor and remove the engine
◉ INSPECTION
● Check the engine coolant temperature by testing it at
the bench as shown in the figure. Connect the tem-
②
perature sensor ① to a circuit tester and place it in ①
the WATER contained in a pan, which is placed on a
stove.
● Heat the water to raise its temperature slowly and
read the column thermometer ② and the ohmmeter.
Temperature sensor specification
Temperature Standard resistance
Water
60℃ Approx. 125 Ϊ
85℃ Approx. 48.5 Ϊ
110℃ Approx. 24 Ϊ
Approx. 15 Ϊ
CAUTION
125℃
● Take special care when handling the tempera-
Multi circuit tester set : 09900-25008 ture sensor. It may cause damage if it gets a
If the resistance noted to show infinity or too much dif- sharp impact.
ferent resistance value, replace the temperature sensor ● Do not contact the engine coolant temperature
with a new one. sensor ① and the column thermometer ② with
a pan.
◉ INSTALLATION
● Tighten the engine coolant temperature sensor to the
specified torque.
Engine coolant temperature sensor
: 18 N∙ ∙m (1.8 kg∙ ∙m)
● Bleed air from the cooling circuit. (Refer to page 2-25)
COOLING SYSTEM 5-8
THERMOSTAT
◉ REMOVAL
● Place a rag under the thermostat case.
● Remove the thermostat case cap.
● Remove the thermostat ①.
◉ INSPECTION
Inspect the thermostat pellet for signs of cracking.
Test the thermostat at the bench for control action, in
the follwing manner.
● Pass a string between flange, as shown in the photo-
graph.
● Immerse the thermostat in the WATER contained in a
beaker, as shown in the illustration. Note that the
immersed thermostat is in suspension. Heat the
water by placing the beaker on a stove ① and
observe the rising temperature on a thermometer ②.
● Read the thermometer just when opening the ther-
mostat. This reading, which is the temperature level
at which the thermostat valve begins to open, should
be within the standard value.
②
Thermostat valve
Standard
operation temperature
Valve opening 88℃ (190℉)
Valve full open 100℃ (212℉) Water
Valve closing 83℃ (181℉)
①
5-9 COOLING SYSTEM
● Keep on heating the water to raise its temperature.

● Just when the water temperature reaches specified
value, the thermostat valve should have lifted by at
least 8.0 mm (0.31 in).
Standard �
Thermostat valve lift � Over 8.0mm at 100℃
(Over 0.31in at 212℉)
● A thermostat failing to satisfy either of the two

requirements, start-to-open temperature and valve
lift, must be replaced.
◉ INSTALLTION
● Apply engine coolant to the rubber seal on the ther- ①
mostat.
● Install the thermostat.
NOTE
The jiggle valve ① of the thermostat faces
upside.
● Install the thermostat case cap ②.

②
NOTE
The rib of the thermostat case cap ② should
be faced upward.
● Tighten the thermostat case bolts to the specified

torque.
Thermostat case bolt : 10 N∙ ∙m (1.0 kg∙
∙m)
● Bleed air from the cooling circuit.
COOLING SYSTEM 5-10
WATER PUMP
◉ REMOVAL AND DISASSEMBLY ①
● Drain engine oil. (Refer to page 2-12) ③
● Remove the water pump cover.
● Remove the radiator outlet hose cover.
● Disconnect the water hoses ①, ②, ③.
● Remove the water pump case and clutch cover. ②
NOTE
Before draining engine oil and engine coolant,
inspect engine oil and coolant leakage
between the water pump and clutch cover.
If engine oil is leaking, visually inspect the oil
seal and O-ring. If engine coolant is leaking,
visually inspect the O-ring
● Remove the snap ring and water pump driven gear

④.
● Remove the pin ⑤ and washer ⑥.
⑥
5-11 COOLING SYSTEM
● Remove the water pump ① from the clutch

cover.
● Remove the O-rings ②.

②
● Remove the E-ring ③ from the impeller shaft.
● Remove the impeller ④ from the other side.
④
COOLING SYSTEM 5-12
● Remove the bearing.
NOTE
If there is no abnormal noise, bearing removal
is not necessary.
◉ INSPECTION
▣ BEARING
Inspect the play of the bearing by hand while it is in the
water pump case.
Rotate the inner race by hand to inspect abnormal
noise and smooth rotation.
Replace the bearing if there is anything unusual.
▣ BEARING CASE
Visually inspect the bearing case for damage.
Replace the water pump body if necessary.
◉ REASSEMBLY AND INSTAL-

LATION
● Install the bearing.
NOTE
The stamped mark on the bearing faces to the
crankcase side.
5-13 COOLING SYSTEM
● Apply SUPER GREASE“A”to the impeller shaft.

SUPER GREASE“A”
● Install the impeller to the water pump body.
● Fix the impeller shaft with the E-ring ①.

● Fill the bearing with engine oil until engine oil comes
out from the hole of the bearing housing.
● Apply engine coolant to the O-ring ②.

● Install a new O-ring. ②
CAUTION
Use a new O-ring to prevent engine coolant
leakge.
● Connect the water hoses.

● Install the radiator outlet hose cover.
● Install the water pump cover.
● Pour engine oil. (Refer to page 2-12)
ELECTRICAL SYSTEM
CONTENTS
LOCATION OF ELECTRICAL COMPONENTS ………………… 6- 1

IGNITION SYSTEM………………………………………………………… 6- 3
CHARGING SYSTEM …………………………………………………… 6- 7
STARTER SYSTEM AND
SIDE STAND IGNITION INTERLOCK SYSTEM ………………… 6-11
SWITCHES …………………………………………………………………… 6-15
LAMP …………………………………………………………………………… 6-16
BATTERY …………………………………………………………………… 6-18
6
6-1 ELECTRICAL SYSTEM
LOCATION OF ELECTRICAL COMPONENTS
③ ④ ⑤ ⑦
①
②
⑥
① Battery ⑤ Engine coolant temperature sensor ⑦ Front brake lamp switch
② Head lamp relay ⑥ Thermostat
③ Side stand relay
④ Cooling fan motor relay
⑧ ⑨
⑧ Side stand switch ⑨ Rear brake lamp switch ⑩ Starter motor

ELECTRICAL SYSTEM 6-2
⑫ ⑬
⑭
⑮
⑪ Ignition coil (NO.1 & NO.2) ⑫ Regulator / Rectifier ⑭ Cooling fan motor
⑬ Turn signal relay ⑮ Cooling fan thermo-switch
� �
� �
� Fuses � Magneto � Gear position switch

� Igniter
IGNITION SYSTEM
is started as the battery discharged ignition system without a contact point. The battery ignition system is
composed a rotor with four rotor tip, the igniter, the ignition coil and battery. This system ignites after get signal from igni-
tion timing of pick-up with the electric energy of this battery and occur the 1st electric current. Therefore, a high voltage
current is induced in the secondary winding of the ignition coil and results in strong spark between spark plug gap.
Igniter
Magneto
IG. S/W
ENGINE STOP S/W
Y
Rr. IGNITION COIL
Ft. IGNITION COIL
G
IGNITER
FUSE
Y REG
REC
L BATTERY
Y
12V 12Ah
Ignition coil & Spark plug

◉ INSPECTION
▣ MAGNETO
Using the pocket tester, measure the resis-
t a n c e between the lead wires in the following
table.
Pick-up coil G-L 80�120 Ϊ
Charging coil Y-Y 0.4�0.9 Ϊ
Pocket Tester : 09900-25002
CAUTION
When mounting the stator on the magneto cover,
apply a small quantity of THREAD LOCK“1324”
to the threaded parts of screws.
WIRE COLOR
L : Blue
G : Green
Y : Yellow
BY : Black with Yellow tracer
OB : Orange with Black tracer
Br : Brown
BW : Black with White tracer
WL : White with Blue tracer
YG : Yellow with Green tracer
▣ SPARK PLUG
Clean the plug with a wire brush and pin. Use the pin
to remove carbon, taking care not to damage the
porcelain.
● Check the gap with a thickness gauge.
0.7 � 0.8 mm
Spark plug gap
(0.028 � 0.032 in)
0.7 � 0.8 mm
(0.028 � 0.032 in)
▣ IGNITION COIL
● Pull out the spark plug.
● Place it on the cylinder head after installing it at the
plug cap to obtain ground.
● Push the electric starter switch to rotate the starter
motor, to have the test of sparking performance.
● If spark doesn’ t emit or the spark bring out the
orange color, replace the ignition coil.
CAUTION
① ②
The ignition coil is marked the“F”for front, and
the“R”for rear. ① Front cylinder ignition coil ② Rear cylinder ignition coil
If otherwise, it may occur severe damage to the
engine.
▣ IGNITION COIL (Checking with Pocket Tester)

● A pocket tester or an ohm meter may be
used, instead of the electro tester. In case, the
ignition coil is to be checked for continuity in both
primary and secondary windings. Exact ohmic read- B/R
ings are not necessary, but, if the windings are
in good condition, their continuity will be noted
with approximate ohmic values.
Ground
Ignition coil resistance Plug cap
Primary 3.5�5.5Ϊ Tester knob indication × 1Ϊ range
Secondary 20�31 ㏀ Tester knob indication × 1㏀ range
Check the attached plug cap
Pocket tester : 09900-25002

▣ IGNITER
Using the pocket tester(R × 1㏀ range), measure the
resistance between the terminal in the following table.
Pocket Tester : 09900-25002
CAUTION
� Numberical value may differ a little according
to the tester.
� Please remind that there may be a defect
which can not be identified even though the
measurement by using the tester indicates a
low voltage.
� The range of measurement adjust a [ X 1㏀ ]
unit.
Unit : kΪ
� TESTER PROBE
① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ⑪ ⑫ ⑬ ⑭ ⑮ �
① OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
② OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
③ 250~370 250~380 18~27 22~33 OFF 9.2~13.8 37~55 23.6~35.4 21.6~32.4 22.4~33.6 18~27 53~79 29.5~44.5 9.2~13.8 21.3~31.9
� ④ 180~270 180~270 2.9~4.4 2.8~4.2 OFF 8.4~12.6 9.6~14 3.8~5.8 2.7~4.1 3~4.6 0 46~69 6.4~9.6 7.1~10.4 2.2~3.4
T ⑤ 180~270 180~270 9.6~14 2.8~4.2 OFF 9.6~14 12.2~18.2 2.6~4 1.4~2 1.8~2.6 2.8~4.2 49~73 9.1~13.7 8.6~13 0.9~1.3
E
⑥ OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
S
T ⑦ 200~300 210~310 21.5~32.5 11.1~16.7 14.3~21.5 OFF 25.7~38.5 15.4~23 14.2~21.2 14.6~21.8 11.2~16.8 39~59 20.4~30.6 4.7~7.1 13.7~20.5
E ⑧ OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
R
⑨ 180~270 190~280 11~16.4 3.8~5.7 2.6~4 OFF 10.8~16.2 13.6~20.4 2.4~3.6 0.9~1.3 3.9~5.9 50.5~75.5 10.4~15.6 9.6~14 1.8~2.8
P ⑩ 180~270 190~280 9.6~14 2.5~3.8 1.4~2 OFF 8.7~13.1 12~18 2.4~3.6 1.4~2 2.6~3.8 48~72 8.8~13.2 8~12 0.6~0.8
R
⑪ 180~270 180~270 10~15 3.1~4.7 1.7~2.5 OFF 9.6~14 12.5~18.7 0.9~1.3 1.5~2.3 3.1~4.7 49.5~74.5 9.6~14 8.8~13.2 1~1.4
O
B ⑫ 170~260 180~270 7~10.4 0 2.8~4.2 OFF 8.5~12.7 9.6~14 3.9~5.9 2.6~4 3~4.6 46.5~69.5 6.4~9.6 7.2~10.8 2.3~3.5
E ⑬ 330~490 330~500 180~270 150~230 80~120 OFF 170~250 190~280 150~230 150~230 150~230 150~230 170~260 165~245 146~219
⑭ 200~300 180~270 17.5~26.5 8.6~12.8 7.3~10.9 OFF 17.5~26.5 21.2~31.8 8.2~12.4 7~10.6 7.3~10.9 8.6~12.8 69~103 16.3~24.5 6.4~9.6
⑮ 200~300 210~310 16.5~24.5 7.4~11 10~15 OFF 4.6~7 20.8~31.2 11.4~17 10~15 10.4~15.6 7.3~10.9 34~51 15.6~23.4 9.6~14
� 170~260 180~270 9~13.5 2.3~3.5 0.9~1.3 OFF 8.8~13.2 11.4~17 1.8~2.8 0.6~1 0.9~1.3 2.3~3.5 48~72 8.6~13 8.1~12.1
CHARGING SYSTEM
The circuit of the charging system is indicated in figure, which is composed of the AC generator, regulator /
rectifier unit and battery. The AC current generated from the AC generator is converted by the rectifier
and is turned into the DC current, then it charges the battery.
Regulator / Rectifier
IG. switch
A. C generator
Battery
IC
LOAD
◉ FUNCTION OF REGULATOR
While the engine rpm is low and the generated current of the AC generator is lower than the adjusted voltage
of the regulator, the regulator does not function, incidentally the generated current charges the battery directly.
IG. switch
A. C generator
Battery
IC
LOAD
When the engine rpm become higher, the generated voltage of the AC generator also becomes higher and
the voltage between points � and � of the regulator accordingly becomes high, and when it reaches the
adjusted voltage of the control unit, consequently the control unit becomes“ON”condition. On the“ON”con-
dition of the control unit, signal will be sent to the SCR (Thyristor) gate probe and SCR will become“ON”
condition. Then the SCR becomes conductive to the direction from point � to point �. Namely at the state of
this, the current generated from the AC generator gets through SCR without charging the battery and returns to
the AC generator again. At the end of this state, since the AC current generated from the AC generator flows into
the point �, reverse current tends to flow to SCR, then the circuit of SCR turns to“OFF”mode and begins to
charge the battery again. Thus these repetitions maintain charging constant voltage to the battry and protect it
from overcharging.
IG. switch
A. C generator
Battery
IC
LOAD
◉ INSPECTION
▣ CHARGING OUTPUT CHECK
Start the engine and keep it running at 5,000 rpm.
Using the pocket tester, measure the DC volt-
age between the battery terminal � and �.
If the tester reads under 13.5V or over 15.0 V, check
the magneto no-load performance and regulator /
rectifier.
CAUTION
When making this test, be sure that the battery is
full-charged condition.
IG. switch
Standard charge 13.5�15.0V (at 5,000 rpm)

Regulator
Rectifier
Battery DCV
▣ MAGNETO NO-LOAD PERFORMANCE

Disconnect the three lead wires from the magneto
terminal.
Start the engine and keep it running at 5,000 rpm.
Using the pocket tester, measure the AC volt-
age between the three lead wires.
If the tester reads under 70 V the magneto is faulty.
Standard NO-load perfor-

Over 70 V (at 5,000 rpm)
mance of magneto

▣ REGULATOR / RECTIFIER
● Disconnect the coupler.
● Using the pocket tester (× 1 ㏁ range), measure the
resistance between the terminals in the following
table.
If the resistance checked is incorrect, replace the regu
lator / rectifier.
Unit : ㏁
� Tester probe
① ② ③ ④ ⑤
� Tester probe
① 3�4㏁ 3�4㏁ 1�2㏁ 1�2㏁

② 3�4㏁ 3�4㏁ 1�2㏁ 1�2㏁
③ 3�4㏁ 3�4㏁ 1�2㏁ 1�2㏁
④ 1�2㏁ 1�2㏁ 1�2㏁ 32㏀ ①
⑤ 1�2㏁ 1�2㏁ 1�2㏁ 32㏀ ④
②
③
⑤
STARTER SYSTEM AND SIDE STAND IGNITION INTER-

LOCK SYSTEM
◉ STARTER SYSTEM DESCRIPTION
The starter system consists of the following components : the starter motor, starter relay, clutch lever position
switch, igniter, side stand switch, gear position switch, starter switch, engine stop switch, ignition switch and battery.
Pressing the starter switch (on the right handlebar switch) energizes the starter relay, causing the contact
points to close, thus completing the circuit from the starter motor to the battery.
START
SWITCH IG. SWITCH
FUSE
NEUTRAL
INDICATOR
BATTERY
CLUTCH LEVER NEUTRAL
SWITCH SWITCH
SIDE STAND
RELAY SIDE STAND
START START RELAY SWITCH
MOTOR
◉ SIDE STAND / IGNITION INTERLOCK SYSTEM DESCRIPTION

This side stand / ignition interlock system prevents the motorcycle from being started with side stand down.
The system is operated by an electric circuit provided between the battery and ignition coil.
The circuit consists of the igniter, neutral indicator light and switches.
The ignition coils will send voltage to the spark plugs depending on what gear the transmission is in and
whether the side stand is either up or down.
The gear position and side stand switches work together in this system.
The ignition coil work only in two situations as follows.
SIDE STAND
RELAY
IGNITION SWITCH
BATTERY IGNITION COIL
NEUTRAL
INDICATOR LIGHT
DIODE
SIDE STAND SW.

NEUTRAL SW.
▣ TRANSMISSION : Neutral -“ON”

Side stand - Down
Clutch lever - Pull
SIDE STAND RELAY

IGNITION SWITCH “ON”
“ON”
NEUTRAL
INDICATOR LIGHT
DIODE
SIDE STAND SW.

NEUTRAL SIDE STAND
SW.“ON” “DOWN POSITION”
▣ TRANSMISSION : Neutral -“OFF”

Side stand - Up
Clutch lever - Pull
SIDE STAND RELAY

“ON”
IGNITION SW.
“ON”
NEUTRAL
INDICATOR LIGHT
DIODE
NEUTRAL SW. SIDE STAND SW.

“OFF” “UP-RIGHT POSITION”
is equipped with the side stand ignition interlock system.

If the transmission is in neutral or side stand up, you can only start the engine with pulling the clutch lever.
No Neutral switch Clutch lever Side stand Engine Start

1 ● ● △ Possible
NOTE
2 △ ● ● Possible
● On or Up.
3 ● △ △ Impossible
△ Off or Down
4 △ ● △ Impossible
5 △ △ ● Impossible
◉ STARTER MOTOR REMOVAL

AND DISASSEMBLY
● Disconnect the starter motor lead wire.
● With loosening the bolts ①, remove the starter
motor.
● Disassemble the starter motor.
①
◉ STARTER MOTOR INSPEC-

TION
▣ CARBON BRUSH
Inspect abnormal wear, crack or smoothness of
the brushes in the brush holder.
If the brush has failed, replace the brush sub assy.
▣ COMMUTATOR
Inspect discoloration, abnormal wear or undercut � of
the commutator.
If the commutator is abnormally worn, replace the Segment
armature. �
When surface is discolored, polish it with #400
sand paper and clean it with dry cloth.
▣ ARMATURE COIL INSPECTION

Check continuity between each segment.
Check continuity between each segment and the
armature shaft.
If there is no continuity between the segments or
there is continuity between the segment and shaft,
replace the starter motor with a new one.

▣ STARTER MOTOR REASSEMBLY

Reassemble the starter motor. Pay attention to the following points :
● Reassembly the starter motor as shown in the illustration.
● Align the mark ① on the housing with the line ②

on the housing end. ① ② ② ①
● Apply SUPER GREASE “A”to the O-ring ③

and remount the starter motor.
③
SUPER GREASE“A”
SWITCHES
Measure each switch for continuity using a tester. If any abnormality is found, replace the respective switch
assemblies with new ones.
IGNITION SWITCH ENGINE STOP SWITCH

R O BW BR O OB
ON ○ ○
OFF ○ ○
HAZARD SWITCH STARTER SWITCH

Sb Gr OB YR
ON ○ ○ ON ○ ○
OFF OFF
DIMMER SWITCH HORN SWITCH

YW Y W BBr BW
HI ○ ○ ON ○ ○
LO ○ ○ OFF
TURN SIGNAL SWITCH FRONT/REAR BRAKE LAMP SWITCH

Lg Sb B O WB
L ○ ○ ON ○ ○
PUSH OFF
R ○ ○
PASS SWITCH
O Y
ON ○ ○
OFF
LAMP
◉ HEADLAMP
◉ TURN SIGNAL LAMP
◉ TAIL / BRAKE LAMP

◉ COMBINATION METER
Remove the combination meter.
Disassemble the combination meter as shown in
the illustration.
▣ INSPECTION
Using the pocket tester, check the continuity
between lead wires (Blue color coupler) in the follow-
ing illustration.
If the continuity measured incorrect, replace the
respective part.
CAUTION
When making this test, it is not necessary to
remove the combination meter.
BATTERY
◉ CAUTION OF BATTERY TREATMENT
The battery needs attention generally as it occur flammability gas.
If you don’t follow the instruction in the below, there may be a explosion and severe accident.
Therefore, please pay attention to the following points.
● Positively prohibit battery from contacting to short, spark or firearms.

● The recharge of battery should be done in the wide place where the wind is well ventilated.
Please don’t recharge it at the sight of wind-proof.
◉ CAUTION OF BATTERY ELECTROLYTE TREATMENT

● Pay attention to the battery electrolyte not to stains the chassis or the humanbody.
● If stains the chassis or the humanbody, at once wash a vast quantity of water.
When they were stained, clothes will come into being a hole or painting will take off.
Consult a doctor.
● When the battery electrolyte was dropped to the surface of land, wash it with a vast quantity of water.
Neutralize by hydroxide, bicarbonate of soda and so on.
◉ CAUTION OF MAINTENANCE
FREE BATTERY TREATMENT
● Do not remove the aluminum tape to seal the bat-
tery electrolyte filler hole until use as battery of com-
plete seal type.
● Do not use it except the battery electrolyte.
● Pouring into the battery electrolyte, necessarily
use the electrolyte of the specified capacity.
● Do not open the sealing cap after recharging the
battery eletrolyte.
▣ FILLING ELECTROLYTE
① Put the battery on even land and remove the alu-
minum tape sealing.
② Remove the cap at the electrolyte container.
Aluminum tape
CAUTION
Do not remove the seal of the electrolyte
Filler holes
container, not prick with sharp thing.
Cap Seal
③ Pouring of battery electrolyte

When insert the nozzles of the electrolyte container into
the battery’s electrolyte filler holes, holding the container
firmly so that it does not fall.
Take precaution not to allow any fluid to spill.
CAUTION
The pouring of electrolyte may not be done if
the electrolyte container is pushed slopely.
④ Confirmation of pour
Make sure that air bubbles are coming up each
electrolyte container, and keep this position for more
than about 20 minutes.
CAUTION
If no air bubbles are coming up from a filler Air bubble
port, tap the bottom two or three times.
⑤ Separation of electrolyte container

After confirming that you entered the electrolyte into
battery completely, remove the electrolyte containers
from the battery.
CAUTION
Draw the empty receptacle out slowly because
there may be a chance remaining electrolyte
vaporize.
⑥ Insert the caps

Insert the cap into the filler holes, pressing it firmly so
that the top of the caps do not protrude above the upper
surface of the battery’s top cover.
Insert the caps firmly

◉ SERVICING
Visually inspect the surface of the battery container. If
any signs of cracking or electrolyte leakage from the
sides of the battery have occurred, replace the battery
with a new one. If the battery terminals are found to be
coated with rust or an acidic white powdery substance,
then this can be cleaned away with sandpaper.
◉ RECHARGING OPERATION
● Using the pocket tester, check the battery voltage. If
How to charge
the voltage reading is less than the 12.0V (DC),
recharge the battery with a battery charger. Standard 1.2 A × 5~10 hours
Fast 6 A × 30 minutes
CAUTION
When recharging the battery, remove the battery
from the motorcycle.
NOTE
Do not remove the caps on the battery top while
recharging.
CAUTION
Be careful not to permit the charging current to
exceed 6A at any time.
● After recharging, wait for more than 30 minutes and
check the battery voltage with a pocket tester.
● If the battery voltage is less than the 12.5V, recharge
the battery again.
● If battery voltage is still less than 12.5V, after
recharging, replace the battery with a new one.
● When the motorcycle is not used for a long period,
check the battery every 1 month to prevent the bat-
tery discharge.
CHASSIS
CONTENTS
EXTERIOR PARTS ………………………………………………………… 7- 1

FRAME COVER …………………………………………………………… 7- 2
SEAT TAIL COVER & SEAT TAIL COVER BRACE …………… 7- 4
FRONT WHEEL …………………………………………………………… 7- 6
FRONT BRAKE …………………………………………………………… 7-10
HANDLEBARS ……………………………………………………………… 7-17
FRONT FORK ……………………………………………………………… 7-20
STEERING …………………………………………………………………… 7-28
REAR WHEEL ……………………………………………………………… 7-31
REAR BRAKE ……………………………………………………………… 7-36
REAR SHOCK ABSORBER …………………………………………… 7-38
SWINGARM ………………………………………………………………… 7-40 7
7-1 CHASSIS
EXTERIOR PARTS
◉ FRONT FENDER
● Remove the three bolts for rightside and the two bolts
for lelfside.
● Remove the front fender.
◉ SEAT
● To remove the seat, remove the seat mounting bolt
on the rearside of the seat.
● To install the seat, slide the seat hook into the seat
hook retainer and install the seat mounting bolt.
CHASSIS 7-2
FRAME COVER
◉ RIGHT DECORATION COVER

● With the right decoration cover mounting screw ①
removed, remove the right decoration cover ②.
②
①
7-3 CHASSIS
◉ LEFT DECORATION COVER

● With the left decoration cover mounting screw ①
removed, remove the left decoration cover ②. ②
◉ RIGHT FRONT SIDE COVER

The right front side cover is used to operate the radiator ④
cap.
● With the two mounting bolts ③ removed, remove the
right front side cover ④.
◉ LEFT FRONT SIDE COVER

The left front side cover is used to inspect the fuses. ⑥
● With the two mounting bolts ⑤ removed, remove the
left front side cover ⑥.
⑤
◉ RIGHT & LEFT AIR DUCT
REAR COVER
● Remove the front side cover, right and left. ⑨
● Remove the bolts ⑦, ⑧ inside of the cover using the
tool in the lower direction.
● Remove the air duct rear cover, right and left, to take ⑦
care of the hook ⑨, ⑩.
CAUTION ⑩ ⑧
If the air duct rear cover was removed
forcedly, damage parts by reason of hook
⑨, ⑩.
CHASSIS 7-4
SEAT TAIL COVER & SEAT TAIL COVER BRACE

● Remove the rear shock absorber upper bolts inside
of frame, right and left.
● Install the rear shock absorber upper bolts with the
frame in the outside direction temporarily.
7-5 CHASSIS
● Remove the battery ① and relay ②, ③, ④.

● Disconnect the rear turn signal lamp coupler and ①
rear combination lamp coupler ⑤. ②
④
⑤
● Remove the two bolts ⑥.
● With the two bolts ⑦ removed, remove the seat tail

cover and seat tail cover brace.
⑦
CHASSIS 7-6
FRONT WHEEL
◉ REMOVAL
● Loosen the axle pinch bolt ①, right and left.
● Loosen the front axle ②.
● Raise the front wheel off the ground with a block
or jack.
②
CAUTION
When using a jack, take care not to cause
scratches on the chassis.
● Remove the front wheel by removing the front ①

axle ②.
7-7 CHASSIS
● Remove the brake disk, right and left.
[Left front brake]
[Right front brake]

◉ INSPECTION AND DISASSEMBLY
▣ TIRE
For inspection of the tire : Refer to page 2-22.
▣ FRONT AXLE
Measure the front axle runout using the dial gauge.
If the runout exceeds the limit, replace the front axle.
Service limit
Axle shaft runout
0.25 mm (0.01 in)
Dial gauge : 09900-20606

V-block : 09900-21304
▣ WHEEL
Make sure that the wheel runout (axial and radial)
does not exceed the service limit when checked as
shown. An excessive amount of runout is usually due
to worn or loose wheel bearings and can be corrected
by replacing the bearings. If bearing replacement fails
to reduce the wheel.
Wheel runout Service limit
(axial and radial) 2.0 mm (0.08 in)
CHASSIS 7-8
▣ WHEEL BEARING
Inspect the play of the wheel bearings by finger
while they are in the wheel. Rotate the inner race by
finger to inspect abnormal noise and smooth rotation.
Replace the bearing in the following procedure if there
is anything unusual.
▣ WHEEL BEARING REMOVAL

● Remove the wheel bearing by using the special tool.
Wheel bearing remover : 09941-50111
CAUTION
The removed bearing should be replaced with
new ones.
◉ REASSEMBLY
Reassemble the front wheel in the reverse order
of removal and disassembly.
Pay attention to the following points :
▣ WHEEL BEARING
● Apply SUPER GREASE“A”to the wheel bearings.
SUPER GREASE“A”
● Install the wheel bearings as follows by using

the special tools.
Steering race installer : 09941-34513
CAUTION
First install the right wheel bearing, then install
the left wheel bearing.
7-9 CHASSIS
▣ BRAKE DISK
Make sure that the brake disk is clean and free of any
greasy matter.
● Apply THREAD LOCK“1324”to the right and left
disk mounting bolts and tighten them to the speci-
fied torque.
Brake disk bolt

: 18~28 N∙m (1.8 ~2.8 kg∙m)
[Left front brake]
[Right front brake]

● Tighten the front axle bolt ① and axle pinch bolt ②
to the specified torque.
Front axle bolt : 50~80 N∙m (5.0 ~8.0 kg∙m)
Front axle pinch bolt
: 15~25 N∙m (1.5 ~2.5 kg∙m)
② ①
CHASSIS 7-10
FRONT BRAKE
WARNING
� Do not mix brake fluid with different brand.
� Do not use a brake fluid kept in an open container or stored for long period of time.
� To store brake fluid, make sure to seal the container and keep it in a safe place to be out of reach of
children.
� When filling brake fluid, take care not to allow water or dirt to enter the system.
� To wash the brake system parts, use brake fluid and not any other material.
� Do not allow dirt and fluid to contact the brake disk or pad.
7-11 CHASSIS
CAUTION
Do not allow brake fluid to contact the paint surface, plastic or rubber parts, or its chemical reaction can cause
discoloration or crack.
◉ BRAKE FLUID REPLACEMENT

● For replacing procedure of brake fluid : Refer to page 2-18
◉ BRAKE PAD REPLACEMENT

● For replacing procedure of brake pad : Refer to page 2-18
◉ CALIPER DISASSEMBLY
● Drain brake fluid. (Refer to page 2-18)
②
CAUTION
To prevent brake fluid from splashing on the
parts nearby, cover the parts with cloth.
● Remove the right and left front brake union bolt ① ①

and caliper mounting bolts ②.
● Remove the brake pad. (Refer to page 2-18) [Left front brake]
①
[Right front brake]
● Remove the brake pad mounting bolt ③.
③
CHASSIS 7-12
● Remove the brake caliper holder ①.

①
● Using an air gun, push out the caliper piston.
WARNING
� Place a rag over the piston to prevent it from
popping out and flying and keeping hand off
the piston.
� Be careful of brake fluid which can possibly
splash.
� Do not use high pressure air but increase the
pressure gradually.
● Remove the dust seal ② and piston seal ③.
CAUTION
� Care not to cause scratch on the cylinder bore.
� Do not reuse the piston seal and dust seal that
have been removed. ② ③
◉ CALIPER INSPECTION
Inspect the caliper cylinder wall and piston surface
for scratch, corrosion or other damages.
If any abnormal condition is noted, replace the caliper.
7-13 CHASSIS
◉ CALIPER REASSEMBLY
Reassemble the caliper in the reverse order of
disassembly procedures and observe the following
points.
CAUTION
� Wash the caliper components with fresh brake
fluid before reassembly. Do not wipe off
brake fluid after washing the components.
� Replace the piston seal and dust seal into new
ones with brake fluid applied.
Brake fluid specification and classification

● Install the brake pad spring.
● Apply SILICONE GREASE to the brake caliper

holder.
SILICONE GREASE
● Install the brake pads. (Refer to page 2-18)
● Tighten the caliper mounting bolts �.

● With the hose end seated to the stopper, tighten �
the right and left front brake hose union bolt �.
Front brake caliper mounting bolts
: 18~28 N∙m (1.8~2.8 kg∙m)
Front brake hose union bolts
: 20~25 N∙m (2.0~2.5 kg∙m)
● Fill the system with brake fluid and bleed air. (Refer
to page 2-19) �
Inspection after reassembly : Refer to page 2-17
[Left front brake]

CHASSIS 7-14
[Right front brake]
◉ BRAKE DISK INSPECTION

Check the brake disk for damage or cracks. Measure
the thickness using the micrometer.
Replace the brake disk if the thickness is less than the
service limit or if damage is found.
Service limit
Brake disk thickness
3.0 mm (0.12 in)
Micrometer (0�25 mm) : 09900-20201
Measure the runout using the dial gauge.

Replace the brake disk if the runout exceeds the ser-
vice limit.
Service limit
Brake disk runout
0.3 mm (0.012 in)
Dial gauge : 09900-20606

● If measurement exceeds the service limit,

replace the brake disk. (Refer to page 7-7)
◉ MASTER CYLINDER DISAS-

SEMBLY ①
● Drain brake fluid the master cylinder.
● Disconnect the brake lamp switch lead wire coupler.
● Remove the union bolt ①.
CAUTION
Place a rag under the union bolt so that brake
fluid can not contact the parts.
7-15 CHASSIS
● Remove the two clamp bolts and take off the mas-
ter cylinder.
● Remove the two fitting screws and separate the

cap and diaphragm.
● Detach the dust seal boot ① and remove the circlip.

● Pull out the piston/cup set ② and spring ③.
③ ② ①
◉ MASTER CYLINDER INSPECTION

Inspect the master cylinder bore for any scratches
or other damage.
Inspect the piston surface for any scratches or
other damage.
CHASSIS 7-16
◉ MASTER CYLINDER REASSEMBLY

Reassemble the master cylinder in the reverse order
of disassembly.
CAUTION
� Wash the master cylider components with new
brake fluid before reassembly.
� When washing the components, use the speci-
fied brake fluid. Never use different types of
fluid or cleaning solvents such as gasoline,
kerosine, etc.
Brake fluid specification and classification

NOTE
When installing the circlip, make sure that the sharp
edge of the circlip faces outside.
● When remounting the master cylinder to the handle-

bars, first tighten the clamp bolts for upside as Master Cylinder
shown.
WARNING
Bleed air from the brake fluid circuit after assem- Up
bling master cylinder. (Refer to page 2-19)
Handlebar
Clearance
7-17 CHASSIS
HANDLEBARS
①
◉ HANDLEBARS RIGHT SIDE
PARTS REMOVAL
● Remove the right handlebar switches.
● Disconnect the brake lamp switch lead wires
and remove the master cylinder.
● Remove the handlebar balancer ① and grip ②.
②
◉ HANDLEBARS LEFT SIDE

PARTS REMOVAL
● Remove the left handlebar switches.
● Remove the handlebar balancer ③ and grip ④.
● Remove the clutch lever holder.
③ ④
● Remove the instrument panel mounting bolts.
● With the instrument panel bracket mounting bolts

removed, remove the instrument panel.
CHASSIS 7-18
● Remove the handlebar mounting bolts, right and left.

● Remove the handlebar ①.
◉ REMOUNTING
Perform the remounting work in the reverse order of
the r e m o v a l p r o c e d u r e s w h i l e o b s e r v i n g t h e
following instructions.
● Tighten the handlebar mounting bolts to the
specified torque, right and left.
Handlebar mounting bolts
: 40~50 N∙m (4.0~5.0 kg∙m)
● Align the mating face of clutch lever holders with

the respective punch marks and tighten the bolt.
● Install the brake master cylinder.
(Refer to page 7-16).
7-19 CHASSIS
● A p p l y S U P E R GREASE “A ”t o t h e t h r o t t l e Throttle grip

cables.
SUPER GREASE“A”
● Install the throttle cable and returning cable to
the throttle grip ①, ②.
① : Throttle cable
② : Returning cable
Throttle cable
Rotation
direction
CHASSIS 7-20
FRONT FORK
7-21 CHASSIS
◉ REMOVAL AND DISASSEMBLY

● Remove the front fender. (Refer to page 7-1)
● Take off the front wheel. (Refer to page 7-6)
● Loosen the right and rear front fork upper

and lower clamp bolts.
①
● Remove the front brake hose clamp.
● Pull down right and left front forks.
NOTE
Slightly loosen the front fork cap bolt ① to facili-
tate later disassembly.
● Remove the front fork cap bolt ① from the inner rod
by loosening the lock nut ②.
② ③
CAUTION ①
Do not disassemble the front fork cap ③.
● Remove spacer ④, spring retainer ⑤ and spring ⑥.
⑥ ⑤
④
CHASSIS 7-22
● Remove the outer tube ① from the inner tube.
● Invert the front fork and stroke the inner rod several
times to let out fork oil.
● Under the inverted condition of front fork, drain oil to
hold it for a few time.
● Remove the damper rod bolt.
● Remove the inner rod/damper rod ②.
CAUTION ②
Do not disassemble the inner rod/damper
rod(cartridge).
7-23 CHASSIS
● Remove the dust seal ① and the oil seal stopper ring
②.
● Remove the oil seal ③ and oil seal retainer ④ by

using the special tool.
① ② ③ ④
CAUTION
The removed oil seal must be replaced with a
new one.
◉ INSPECTION ⑤
▣ INNER AND OUTER TUBES
Inspect the inner tube outer surface and outer tube slide
metal ⑤ face for scratches.
If any defects are found, replace them with a new one.
CAUTION
t remove the outer tube slide metal ⑤.
Don’
▣ FORK SPRING
Measure the fork spring free length.
If it is shorter than the service limit, replace it with a new
one.
Standard : 470mm (18.5in)
Front fork spring free Standard
length 470mm (18.5in)
CHASSIS 7-24
▣ INNER ROD/DAMPER ROD

Move the inner rod by hand to examine it for smooth-
ness.
If any abnormal points are found, replace inner
rod/damper rod with a new one.
◉ REASSEMBLY AND REMOUNTING

Reassemble and remount the front fork in the reverse
order of removal and disassembly. Pay attention to the
following points :
▣ DAMPER ROD BOLT
● Insert the inner rod/damper rod into the inner tube. �
● Install the gasket � to the damper rod bolt �, and
apply THREAD LOCK“1324”to the damper rod bolt
� and tighten it to the specified torque.
�
Damper rod bolt
: 30~40 N∙ ∙m (3.0~4.0 kg∙ ∙m)
CAUTION
Use a new gasket to prevent oil leakage.
▣ OIL SEAL AND DUST SEAL

● Apply SUPER GREASE“A”to the new oil seal and
dust seal lips lightly before installing it.
SUPER GREASE“A”
�
● Install the oil seal retainer ①, oil seal ②, oil seal
stopper ring ③ and dust seal ④ to the outer tube.
①
CAUTION ②
● When installing the oil seal to outer tube, be ③
careful not to damage the oil seal lip. ④
● Do not use solvents for washing to prevent oil
seal damage.
● Apply fork oil to the Anti-friction meatal �.
● Make sure that the oil seal stopper ring ③ has
been fitted securely.
▣ OUTER TUBE
● Install the outer tube to the inner tube.
CAUTION
Be careful not to damage the dust seal lip and the
oil seal lip, when installing the outer tube.
7-25 CHASSIS
▣ FORK OIL
● Place the front fork vertically without spring.
● Compress it fully.
● Pour specified front fork oil up to the top level of the
outer tube.
● Move the inner rod slowly more than ten times until
bubbles do not come out from the oil.
NOTE
Refill front fork oil up to the top of the outer tube
to find bubbles while bleeding air.
● Refill specified front fork oil up to the top level of the

outer tube again. Move the outer tube up and down
several strokes until bubbles do not come out from
the oil.
● Keep the front fork vertically and wait 5 ~ 6 minutes.
NOTE
● Always keep oil level over the tube top end, or
air may enter the tube during this procedure.
● Take extreme attention to pump out air com-
pletely.
● Hold the front fork vertically and adjust fork oil level
with the special tool.
NOTE
When adjusting the fork oil level, remove the fork
spring and compress the outer tube fully.
Each leg
Front fork oil capacity
420cc
Standard
Front fork
215mm (8.5in) from end of outer tube
oil level
(when maximum compressed without spring)
Front fork oil specification : TELLUS #32
Front fork oil level gauge : 09943-74111
CHASSIS 7-26
▣ FRONT FORK INNER ROD LOCK NUT

● Adjust the height � of the inner rod threads by turn-
ing the lock nut ① at 11mm(0.43 in) as shown in �
illustration.
①
▣ FORK SPRING ↓
● Install the fork spring as shown in the illustration.
● Install the spring retainer and the spacer. ↑
Upper side
▣ FRONT FORK CAP BOLT

● Hold the cap bolt ② and tighten the lock nut ③ to the
specified torque. ③
Inner rod lock nut ②
∙m (1.75~2.25 kg∙
: 17.5~22.5 N∙ ∙m)
● Install the front fork cap bolt to the outer tube tem-
porarily.
● Set the front fork to the lower bracket temporarily,
tighten the front fork cap bolt ④ to the specified ④
torque.
Front fork cap bolt
: 30~40 N∙∙m (3.0~4.0 kg∙ ∙m)
● With the front fork upper face contacted with the
steering stem upper bracket, tighten the front fork
upper and lower clamp bolts to the specified torque.
Front fork upper clamp bolt
: 22~35 N∙∙m (2.2~3.5 kg∙ ∙m)
Front fork lower clamp bolt
: 22~35 N∙∙m (2.2~3.5 kg∙ ∙m)
7-27 CHASSIS
● Install the left front fork in the same manner as the

right one.
● Install the front fender and tighten its mounting bolts
with finger.
● Install the front wheel. (Refer to page 7-8)
● Install the brake calipers. (Refer to page 7-13)
● Swing the motorcycle up and down several times.
● Tighten the front fender mounting bolts.
● Install the brake hose securely.
◉ FRONT FORK SETTING

After installing the front fork, adjust the rebound and
compression damping force as follows.
▣ DAMPING FORCE ADJUSTMENT
1.Rebound damping force
To adjust the rebound damping force turn in the adjuster ①
① fully for“S”or“H”direction.
Count the number of clicks from the fully turned-in posi-
tion.
Fully turned-in“H”direction provides stiffest rebound
damping force and turning“S”direction the adjuster
will soften rebound damping force.
Standard
Front fork rebound
3 clicks out from end of
damping force adjuster
“H”direction
2. Compression damping force

To adjust the compression damping force turn in the
adjuster ② fully for“S”or“H”direction.
Count the number of clicks from the fully turned-in posi-
tion.
Fully turned-in“H”direction provides stiffest compres- ②
sion damping force and turning“S”direction the
adjuster will soften compression damping force.
Front fork compression Standard
damping force adjuster End of“S”direction
STANDARD FRONT FORK DAMPING FORCE

Rebound Compression
Softer Turn to“S”direction Turn to“S”direction
Solo riding Standard 3 clicks out from end of“H”direction End of“S”direction
Stiffer Turn to“H”direction Turn to“H”direction
Dual riding 3 clicks out from end of“H”direction 2 clicks out from end of“S”direction
WARNING
Be sure to adjust the rebound and compression
damping force on both front fork legs equally.
CHASSIS 7-28
STEERING

● Take off the front wheel. (Refer to page 7-6)
● Remove the front fender. (Refer to page 7-1)
● Take off the front fork. (Refer to page 7-21)
7-29 CHASSIS
● With the instrument panel mounting bolts and instru-

ment panel bracket mounting bolts removed, remove
the instrument panel. (Refer to page 7-17)
● Remove the handlebar mounting bolts, right and left.
● Remove the handlebar. (Refer to page 7-18)
● Remove the steering stem head nut ① and take off
the steering stem upper bracket ②.
①
②
● Remove the steering stem nut ③ and draw out the
steering stem.
Clamp wrench : 09940-10122 ③

● Take off the steering stem lower bracket ④.
CAUTION ⑤
Hold the steering stem lower bracket by hand to
prevent from falling.
④
● Remove the upper and lower bearing ⑤.
● Remove the outer race fitted on the steering stem.

This can be done with a chisel.
● Draw out the two inner races fitted to the top and bot-
tem ends of the head pipe.
CHASSIS 7-30
◉ INSPECTION
Inspect and check the removed parts for the following
abnormalities.
∙Handlebar distortion.
∙Handlebar clamp wear.
∙Abnormality operation of bearing.
∙Worn or damaged races.
∙Distortion of steering stem.
◉ REASSEMBLY
Reassemble and remount the steering stem in the
reverse order of disassembly and removal, and also
carry out the following steps : ②
● Apply SUPER GREASE“A”to the upper bearing
and lower bearing ①.
SUPER GREASE“A”
①
● Tighten the steering stem nut ② with the special tool.
Clamp wrench : 09940-10122
Steering stem nut

∙m (8.0~10.0 kg∙
: 80~100 N∙ ∙m)
● Turn the steering stem right and left, lock-to-lock, five

or six times.
● Tighten the steering stem head nut ③ to the
specified torque.
Steering stem head nut
: 80~100 N∙∙m (8.0~10.0 kg∙ ∙m)
CAUTION
After performing the adjustment and installing
the steering stem upper bracket, rock the front
wheel assembly forward and backward to ensure
that there is no play and that the procedure was
accomplished correctly. If play is noticeable, re-
adjust the steering stem nut.
③
● Tighten the handlebar mounting bolts to the specified
torque, right and left. (Refer to page 7-18)
Handlebar mounting bolts
∙m (4.0~5.0 kg∙
: 40~50 N∙ ∙m)
7-31 CHASSIS
REAR WHEEL
◉ REMOVAL
● Raise the rear wheel off the ground with a jack
or block.
● With the four mounting bolts, remove the engine pul-
ley cover.
CHASSIS 7-32
● With the four mounting bolts, remove the drive belt

cover.
● Loosen the drive belt adjuster ①, right and left.

● Disengage the drive belt from the rear pulley.
● Remove the rear axle bolt ②.

● Remove the rear wheel.
②
7-33 CHASSIS
● With the disk mounting bolts removed, remove the

rear brake disk cover and brake disk.
● Remove the spacer ①.

● Remove the rear pulley ② with mounting drum ③
from the rear wheel.
① ④③ ②
NOTE
Before separating the rear pulley and mounting
drum, slightly loosen the rear pulley bolts.
● Remove the rear wheel shock absorber ④.

● Remove the rear pulley ② from the rear pulley
mounting drum.
▣ WHEEL BEARING REMOVAL

● Remove the bearing using the special tool.
Wheel bearing remover : 09941-50111
CAUTION
The removed bearing should be replaced with
new one.
◉ INSPECTION
WHEEL AXLE : Refer to page 7-7
WHEEL : Refer to page 7-7
WHEEL BEARING : Refer to page 7-8
TIRE : Refer to page 2-22
CHASSIS 7-34
▣ REAR WHEEL SHOCK ABSORBER

Inspect the rear wheel shock absorber for wear and dam-
age.
Replace the rear wheel shock absorber if there is any-
thing unusual.
▣ REAR PULLEY
Inspect the pulley’s teeth for wear. If they are worn,
replace the pulley and drive belt as a set.
◉ REASSEMBLY
Reassemble the rear wheel and r e a r brake in
the reverse order of disassembly.
● Tighten the rear pulley bolts to the specified torque.
Rear pulley bolt
: 20~30 N∙m (2.0~3.0 kg∙m)
● With the rear wheel installed, tighten the rear axle

bolt ① to the specified torque.
Rear axle bolt : 90~140 N∙m (9.0~14.0 kg∙m)
①
7-35 CHASSIS
● After installing the drive belt to the rear pulley,

adjust the drive belt by turning both belt adjusters
①.
● Tighten both belt adjuster lock nuts ② securely.
② ① ① ②
CHASSIS 7-36
REAR BRAKE
WARNING
� Do not mix brake fluid with different brand.
� Do not use a brake fluid kept in an open container or stored for a long period.
� To store brake fluid, make sure to seal the container and keep it in a safe place to be out of reach of
children.
� When filling brake fluid, take care not to allow water or dirt to enter the system.
� To wash the brake system parts, use brake fluid and not any other material.
� Do not allow dirt and fluid to contact the brake disk or pad.
7-37 CHASSIS
◉ Brake fluid replacement : Refer to page 2-18

◉ Brake pad replacement : Refer to page 2-18
◉ Disassembly of caliper : Refer to page 7-11
◉ Inspection of caliper : Refer to page 7-12
◉ Reassembly of caliper : Refer to page 7-13
◉ Inspection of brake disk : Refer to page 7-14
CHASSIS 7-38
REAR SHOCK ABSORBER
◉ REMOVAL
● Remove the rear shock absorbers by removing
their bolts and nuts.
7-39 CHASSIS
◉ INSPECTION
Inspect the rear shock absorber for damage and
oil leakage. If any defects are found, replace the rear
shock absorber with a new one.
CAUTION
Do not attempt to disassemble the rear shock
absorber. It is unserviceable.
◉ REMOUNTING
● Install the rear shock absorber and tighten the bolts
and nuts to the specified torque.
Shock absorber mounting nut (upper)
∙m (2.0~3.0 kg∙m)
: 20~30 N∙
Shock absorber mounting bolt (lower)
∙m (3.5~5.5 kg∙m)
: 35~55 N∙
◉ SPRING PRE-LOAD ADJUSTMENT

● Adjust the rear shock absorber spring pre-load. ①
Rear shock absorber Standard
spring length 223 mm (8.78 in)
Rear shock absorber Standard

spring pre-load 1/5 position
WARNING
②
Unequal suspension adjustment can cause poor
handling and loss of stability. ① Rear shock absorber ② Pin spanner
Adjust the right and left shock absorber to the
same settings.
CHASSIS 7-40
SWINGARM

● Remove the rear wheel. (Refer to page 7-31)
● Remove the exhaust pipes and muffler.
(Refer to page 3-3)
7-41 CHASSIS
● Remove the engine pulley cover and drive belt cover.
● With the rear shock absorber lower bolts removed,

disconnect the rear shock absorber from swingarm.
● Remove the swingarm mounting lock nut.

● Remove the swingarm pivot nut.
● Remove the swingarm by removing the pivot shaft.
CHASSIS 7-42
◉ INSPECTION
▣ SWINGARM
Inspect the swingarm for damage.
If any defects are found, replace the swingarm with
a new one.
▣ SWINGARM PIVOT SHAFT

Measure the pivot shaft runout using the dial gauge.
If the pivot shaft exceeds the service limit, replace it
with a new one.
Swingarm pivot shaft Service limit

runout 0.6 mm (0.024 in)
Dial gauge : 09900-20606

V-block : 09900-21304
7-43 CHASSIS
◉ REASSEMBLY
Reassemble the swingarm and rear shock absorber
in the reverse order of disassembly.
● Install the swingarm and tighten the swingarm
pivot shaft, nut and swingarm mounting lock nut with
the special tool to the specified torque.
Swingarm pivot nut ①
: 50~70 N∙ ∙m (5.0~7.0 kg∙∙m)
Swingarm pivot shaft ②
: 15~30 N∙ ∙m (1.5~3.0 kg∙∙m)
Swingarm mounting lock nut (M26) ③
: 70~80 N∙ ∙m (7.0~8.0 kg∙∙m)
: 09940H35010
● Install the rear wheel. (Refer to page 7-34)

● Adjust the following points :
Drive belt slack : Refer to page 2-15
CAUTION
Set the part � of swingarm pivot shaft ②
align center line by the hand temporarily and
install the swingarm pivot shaft to the speci-
fied torque.
If otherwise, it is damage to the thread of
swingarm pivot shaft.
②
�
③
SERVICING INFORMATION
CONTENTS
TROUBLESHOOTING …………………………………………………… 8- 1
SPECIAL TOOLS ………………………………………………………… 8- 9
TIGHTENING TORQUE ………………………………………………… 8-12
SERVICE DATA …………………………………………………………… 8-14
WIRE AND CABLE ROUTING ………………………………………… 8-24
WIRING DIAGRAM ………………………………………………………… 8-30
8
8-1 SERVICING INFORMATION
TROUBLESHOOTING
◉ ENGINE
Complaint Symptom and possible causes Remedy
Engine will not Compression too low

start, or is hard 1. Valve clearance out of adjustment. Adjust.
to start. 2. Worn valve guides or poor seating of valves. Repair or replace.
3. Valves mistiming Adjust.
4. Piston rings excessively worn. Replace.
5. Worn-down cylinder bore. Replace or rebore.
6. Poor seating of spark plug. Retighten.
7. Starter motor cranks but too slowly. Consult“electrical complaints”
Plug not sparking

1. Fouled spark plug. Clean or replace.
2. Wet spark plug. Clean and dry.
3. Defective ignition coil. Replace.
4. Open or short circuit in high tension cord. Replace..
No fuel reaching the carburetor

1. Clogged hole in the fuel tank cap. Clean.
2. Clogged or defective fuel cock. Clean or replace.
3. Defective carburetor float valve. Replace.
4. Clogged fuel pipe. Clean or replace.
Engine stalls 1. Fouled spark plug. Clean.

easily. 2. Clogged fuel hose. Clean.
3. Clogged jets in carburetor. Clean.
4. Valve clearance out of adjustment. Adjust.
Noisy engine. Excessive valve chatter

1. Valve clearance too large. Adjust.
2. Weakened or broken valve springs. Replace.
3. Worn down camshaft. Replace.
Noise appears to come from piston

1. Piston or cylinder worn down. Replace.
2. Weakened or broken valve springs. Replace.
3. Worn down piston pin or piston pin bore. Replace.
4. Piston rings or ring groove worn. Replace.
Noise seems to come from camshaft drive chain

1. Stretched camshaft drive chain. Replace.
2. Worn camshaft sprockets. Replace.
3. Cam chain tensioner adjuster not working. Repair or replace.
Noise seems to come from clutch

1. Worn splines of countershaft or hub. Replace.
2. Worn teeth of cluth plates. Replace.
3. Distorted clutch plates, driven and drive. Replace.
Noise seems to come from crankshaft

1. Worn or broken bearings. Replace.
2. Big-end bearings worn and broken. Replace.
3. Thrust clearance too large. Replace.
SERVICING INFORMATION 8-2
Noisy engine. Noise seems to come from transmission

1. Gears worn or rubbing. Replace.
2. Badly worn splines. Replace.
3. Primary gears worn or rubbing. Replace.
3. Badly worn bearings. Replace.
Noise seems to come from water pump
1. Too much play on pump shaft bearing. Replace.
2. Worn or damaged impeller shaft. Replace.
3. Contact between pump case and impeller. Replace.
1. Clutch control out of adjustment or too much play. Adjust.
Slipping clutch. 2. Weakened clutch springs. Replace.
3. Worn or distorted pressure plate. Replace.
1. Clutch control out of adjustment or too much play. Adjust.
Dragging clutch.
2. Weakened clutch springs. Replace.
1. Broken gearshift cam. Replace.
Transmission will
2. Distorted gearshift forks. Replace.
not shift.
3. Worn gearshift pawl. Replace.
1. Broken return spring on shift shaft. Replace.
Transmission will
2. Shift shafts are rubbing or sticky. Repair.
not shift back.
3. Distorted or worn gearshift forks. Replace.
1. Worn shifting gears on driveshaft or countershaft. Replace.
Transmission
2. Distorted or worn gearshift forks. Replace.
jumps out of gear.
3. Weakened stopper pawl spring on gearshift cam. Replace.
4. Worn gearshift pawl. Replace.
1. Valve clearance out of adjustment. Adjust.
Engine idles
2. Poor seating of valves. Replace.
poorly.
3. Defective valve guides. Replace.
4. Defective pick-up coil. Replace.
5. Spark plug gap too wide. Adjust or replace.
6. Defective ignition coil resulting in weak sparking. Replace.
7. Float-chamber fuel level out of adjustment in carburetor. Adjust.
8. Clogged jets. Clean.
Engine runs 1. Valve springs weakened. Replace.
poorly in high 2. Valve timing out of adjustment. Adjust.
speed range. 3. Worn cams. Replace.
4. Spark plug gap too narrow. Repair.
5. Defective ignition coil. Replace.
6. Float-chamber fuel level too low. Adjust .
7. Clogged air cleaner element. Clean.
8. Clogged fuel hose, resulting in inadequate fuel supply to carburetor. Clean or replace.
Dirty or heavy 1. Too much engine oil in the engine. Check with inspection win-
exhaust smoke dow, drain out excess oil.
2. Worn piston rings or cylinder. Replace.
3. Worn valve guides. Replace.
4. Cylinder wall scored or scuffed. Replace.
5. Worn valves stems. Replace.
6. Defective stem seals. Replace.
7. Worn side rails. Replace.
Engine lacks power. 1. Loosen of valve clearance. Adjust.
2. Weakened valve springs. Replace.
3. Valve timing out of adjustment. Adjust.
4. Worn piston ring or cylinder. Replace.
5. Poor seating of valves. Repair or replace.
6. Fouled spark plug. Clean or replace.
7. Worn camshaft. Replace.
8. Spark plug gap incorrect. Adjust or replace.
9. Clogged jets in carburetor. Clean.
10. Float-chamber fuel level out of adjustment. Adjust.
11. Clogged air cleaner element. Clean.
12. Too much enging oil. Drain out excess oil.
13. Defective air intake pipe. Retighten or replace.
Engine overheats. 1. Heavy carbon deposit on piston head. Clean.
2. Not enough oil in the engine. Add oil.
3. Defective oil pump or clogged oil circuit. Repair or clean.
4. Fuel level too low in float chamber. Adjust.
5. Air leak from intake pipe. Retighten or replace.
6. Use of incorrect engine oil. Change.
7. Defective cooling system. See“Cooling system”section.
◉ CARBURETOR
Trouble with 1. Starter jet is clogged. Clean.

starting. 2. Starter pipe is clogged. Clean.
3. Air leaking from a joint between starter body and carburetor. Check starter body and
carburetor for tightness,
adjust and replace gasket.
4. Starter plunger is not operating properly. Check and adjust.
Idling or low-speed 1. Pilot jet, pilot air jet are clogged or loose. Check and clean.
trouble. 2. Pilot outlet or bypass is clogged. Check and clean.
3. Starter plunger is not fully closed. Check and clean.
Medium or high 1. Main jet or main air jet is clogged. Check and clean.
speed trouble. 2. Needle jet is clogged. Check and clean.
3. Throttle valve is not operating properly. Check throttle valve for
operation.
4. Filter is clogged. Check and clean.
Overflow and fuel 1. Needle valve is worn or damaged. Replace.

level fluctuations. 2. Spring in needle valve is borken. Replace.
3. Float is not working properly. Check and adjust.
4. Foreign matter has adhered to needle valve. Clean.
5. Fuel level is too high or low. Adjust float height.
◉ RADIATOR (COOLING SYSTEM)

Engine overheats. 1. Not enough engine coolant. Add coolant.

2. Radiator core clogged with dirt or scale. Clean.
3. Faulty cooling fan. Repair or replace.
4. Defective cooling fan thermo-switch. Replace.
5. Clogged water passage. Clean.
6. Air trapped in the cooling circuit. Bleed out air.
7. Defective water pump. Replace.
8. Use of incorrect engine coolant. Replace.
9. Defective thermostat. Replace.
Engine overcools. 1. Defective cooling fan thermo-switch. Replace.

2. Extremely cold weather. Put on the radiator cover.
3. Defective thermostat. Replace.
◉ ELECTRICAL
No sparking or poor 1. Defective ignition coil. Replace.

sparking. 2. Defective spark plug. Replace.
3. Defective igniter. Replace.
Spark plug soon 1. Mixture too rich. Adjust carburetor.

become fouled with 2. Idling speed set too high. Adjust carburetor.
carbon. 3. Incorrect gasoline. Change.
4. Dirty element in air cleaner. Clean or replace.
5. Spark plug too cold. Replace by hot type plug.
Spark plug become 1. Worn piston rings. Replace.

fouled too soon. 2. Pistons or cylinder worn. Replace.
3. Excessive clearance of valve stems in valve guides. Replace.
4. Worn stem oil seal. Replace.
Spark plug 1. Spark plug too hot. Replace by cold type plug.
electrodes 2. The engine overheats. Tune up.
overheat or burn. 3. Spark plug loose. Retighten.
4. Mixture too lean. Adjust carburetor.
Generator charge, 1. Lead wires tend to get shorted or open-circuited or loosely connected Repair or retighten.
but charging at terminals.
rate is below the 2. Grounded or open-circuited stator coils of generator. Replace.
specification. 3. Defective regulator/rectifier. Replace.
4. Not enough electrolyte in the battery. Add distilled water between
the level lines.
5. Defective cell plates in the battery. Replace the battery.
Generator 1. Internal short-circuit in the battery. Replace the battery.

overcharges. 2. Resistor element in the regulator/rectifier damaged or defective. Replace.
3. Regulator/rectifier poorly grounded. Clean and tighten
ground connection.
Unstable 1. Lead wire insulation frayed due to vibration resulting in intermittent Repair or replace
charging. shorting.
2. Generator internally shorted. Replace.
3. Defective regulator/rectifier. Replace.
Starter switch is 1. Battery run down. Recharge or replace.

not effective. 2. Defective switch contacts. Replace.
3. Brushes not seating properly on commutator in starter motor. Repair or replace.
4. Defective starter relay. Replace.
◉ BATTERY
“Sulfation”acidic 1. Not enough electrolyte. Add distilled water, if the battery

white powdery has not been damaged and
substance or spots “sulfation”has not advanced
on surfaces of too far, and recharge.
cell plates. 2. Battery case is cracked. Replace the battery.
3. Battery has been left in a run-down condition for a long time. Replace the battery or recharge.
4. Contaminated electrolyte. (Foreign matter has enters the If“sulfation”has not advanced
battery and become mixed with the electrolyte.) far, try to restore the battery by
replacing the electrolyte,
recharing it fully with the battery
detached from the motorcycle
and then adjusting electrolyte
specific gravity.
Battery runs down 1. The charging method is not correct. Check the generator, regulator
quickly. /rectifier and circuit connections,
and make necessary adjustments
to obtain specified charging
operation.
2. Cell plates have lost much of their active material as a result of Replace the battery, and correct
over-charging. the charging system.
3. A short-circuit condition exists within the battery due to excessive Replace the battery.
accumulation of sediments caused by the high electrolyte specific
gravity.
4. Electrolyte specific gravity is too low. Recharge the battery fully and
adjust electrolyte specific
gravity.
5. Contaminated electrolyte. Replace the electrolyte, recharge
the battery and then adjust
specific gravity.
6. Battery is too old. Replace the battery.
Reversed battery The battery has been connected the wrong way round in the system, so Replace the battery and be
polarity. that it is being charged in the reverse direction. sure to connect the battery
properly.
Battery“sulfation” 1. Charging rate too low or too high. (When not in use, batteries Replace the battery.
should be recharged at least once a month to avoid sulfation.)
2. Battery electrolyte excessive or insufficient, or its specific gravity too Keep the electrolyte up to the
high or too low. prescribed level, or adjust the
specific gravity by consulting
the battery maker’s directions.
3. The battery left unused for too long in cold climate. Replace the battery, if badly
sulfated.
Battery discharges 1. Dirty container top and sides. Clean.

too rapidly. 2. Impurities in the electrolyte or electrolyte specific gravity is too high. Change the electrolyte by
consulting the battery maker’s
directions.
◉ CHASSIS
Steering feels too 1. Steering stem nut overtightened. Adjust.

heavy or stiff. 2. Worn bearing or race in steering stem. Replace.
3. Distorted steering stem. Replace.
4. Not enough pressure in tires. Adjust.
Steering 1. Loss of balance between right and left front suspensions. Replace.
oscillation. 2. Distorted front fork. Repair or replace.
3. Distorted front axle or crooked tire. Replace.
4. Loose steering stem nut. Adjust.
5. Worn or incorrect tire or wrong tire pressure. Adjust or replace.
6. Worn bearing/race in steering stem. Replace.
Wobbling 1. Distorted wheel rim. Replace.

front wheel. 2. Worn-down wheel bearings. Replace.
3. Defective or incorrect tire. Replace.
4. Loosen nut on axle. Retighten.
5. Incorrect front fork oil level. Adjust.
6. Incorrect front wheel weight balance. Adjust.
Front suspension 1. Weakened springs. Replace.

too soft. 2. Not enough fork oil. Refill.
3. Wrong viscous fork oil. Replace.
4. Improperly set front fork damping force adjuster. Adjust.
Front suspension 1. Fork oil too viscous. Replace.

too stiff. 2. Too much fork oil. Drain excess oil.
3. Bent front axle. Replace.
4. Improperly set front fork damping force adjuster. Adjust.
Noisy front 1. Not enough fork oil. Refill.

suspension. 2. Loosen nuts on suspension. Retighten.
Wobbling 1. Distorted wheel rim. Replace.

rear wheel. 2. Worn-down rear wheel bearing. Replace.
3. Defective or incorrect tire. Replace.
4. Loose nut on axle. Retighten.
5. Worn swingarm bushing or bearing. Replace.
6. Loosen nut on the rear shock. Retighten.
Rear suspension 1. Weakened springs. Replace.

too soft. 2. Rear suspension adjuster improperly set. Adjust.
Rear suspension 1. Rear suspension adjuster improperly set. Adjust.

too stiff. 2. Worn swingarm bushing or bearing. Replace.
Noisy rear 1. Loosen nuts on suspension. Retighten.

suspension. 2. Worn swingarm bushing or bearing. Replace.
◉ BRAKES
Poor braking 1. Not enough brake fluid in the reservoir. Refill to level mark.
(FRONT and REAR) 2. Air trapped in brake fluid circuit. Bleed air out.
3. Pads worn down. Replace.
4. Too much play on brake lever or pedal. Adjust.
5. Oil adhesion on friction surface of pads. Clean disk and pads.
6. Worn disk. Replace.
Insufficient brake 1. Leakage of brake fluid from hydraulic system. Repair or replace.
power. 2. Worn pads. Replace.
3. Oil adhesion of engaging surface of pads. Clean disk and pads.
4. Worn disk. Replace.
5. Air in hydraulic system. Bleed air.
Brake squeaking. 1. Carbon adhesion on pad surface. Repair surface with

sandpaper.
2. Tilted pad. Modify pad fitting.
3. Damaged wheel bearing. Replace.
4. Loosen front-wheel axle or rear-wheel axle. Tighten to specified torque.
5. Worn pads. Replace.
6. Foreign material in brake fluid. Replace brake fluid.
7. Clogged return port of master cylinder. Disassemble and clean
master cylinder.
Excessive brake 1. Air in hydraulic system. Bleed air.

lever stroke. 2. Insufficient brake fluid. Replenish fluid to specified
level ; bleed air.
3. Improper quality of brake fluid. Replace with correct fluid.
Leakage of brake 1. Insufficient tightening of connection joints. Tighten to specified

fluid. torque.
2. Cracked hose. Replace.
3. Worn piston and/or cup. Replace piston and/or cup.
SPECIAL TOOLS
Special tools Part Number∙Part Name∙Description Special tools Part Number∙Part Name∙Description
09900-20101 09900-20806
Vernier Caliper Thickness gauge
Used to conveniently measure various dimensions. Measure clearance of piston ring.
09900-20201 09900-21109
Micrometer (0~25mm) Torque wrench
Used for precise measurement (00~25mm measure ranges). Measure torque of tightening.
09900-20202 09900-21304
Micrometer (25~50mm) V-block
Used for precise measurement (25~50mm measure ranges). With using magnetic stand.
09900-20203 09900-22301
Micrometer (50~75mm) Plastigauge
Used for precise measurement (50~75mm measure ranges). Measure clearance of crankshaft thrust.
09900-20204 09900-22401
Micrometer (75~100mm) Small bore gauge
Used for precise measurement (75~100mm measure ranges). Measure inside diameter of conrod small-end.
09900-20508 09900-25002
Cylinder gauge set Pocket tester
Measure inside diameter of cylinder. Measure voltage, electric current, resistance.
09900-20605 09900-25008
Dial calipers Multi circuit tester set
Meassure width of conrod big-end. Inspect thermo-switch or temperature sensor.
09900-20606 09900-26006
Dial gauge Engine tachometer
Meassure oscillation of wheel with using magnetic stand. Measure rotational frequency of engine.
09900-20701 09910-20115
Magnetic stand Conrod holder
With using dial gauge. Used to lock the crankshaft.

09910-32812 09915-64510
Crankshaft installer Compression gauge
Used to install the crankshaft in the crankcase. Measure cylinder compression.
09910-32813 09915-74510
Crankshaft installer adapter Oil pressure gauge
Used to with the crankshaft installer. Measure oil pressure of 4-stroke engine.
09910-34510 09916-14510
Piston pin puller Valve spring compressor
Use to remove the piston pin. Used to remove and remounting valve stem.
09913-10760
09916-14520
Fuel level gauge
Measure height of carburetor.

Used with valve spring compressor.
09913-50121 09920-13120
Oil seal remover Crankcase separater
Used to remove the oil seal. Separate to crankcase.
09913-70122 09920-53710
Bearing installer Clutch sleeve hub holder
Used to drive bearing in. Used to install or remove clutch sleeve hub nut.
09913-75820 09921-20200
Bearing installer Bearing remover (10mm)
Used to drive bearing in. Used to remove bearing with the rotor remove sliding shaft.
09913-76010 09921-20210
09913-80112 09923-73210
09923-74510 09941-50111
Bearing remover (20~35mm) Wheel bearing remover
Used to remove bearing with the rotor remove sliding shaft. Used to remove wheel bearing.
09930-30102 09943-74111
Rotor remove sliding shaft Front fork oil level gauge
Used to with bearing remover. Used to drain the fork oil to the specified level.
09930-30165
Rotor remover
Used to remove rotor.
09940-10122
Clamp wrench
A hook wrench to adjust the steering head of motorcycle.
09940-34520
T-handle
Remove and remounting front fork oil cylinder.
09940-34561
Front fork assembling tool attachment“D”
Used with T-handle.
09940H30010
Used to install or remove engine mounting lock nut.
09940H35010
Used to install or remove swingarm mounting lock nut.
09941-34513
Steering race installer
Used to install steering outer race.

TIGHTENING TORQUE
◉ ENGINE
ITEM N∙m kg∙m
Coolant temperature sensor 18 1.8
Coolant drain bolt 11 ~ 14 1.1 ~ 1.4
Cooling fan mounting bolt 8 ~ 12 0.8 ~ 1.2
Cooling fan motor mounting bolt 8 0.8
Cooling fan thermo-switch 13 1.3
Radiator mounting bolt 8 ~ 12 0.8 ~ 1.2
Magneto rotor bolt 110 ~ 170 11.0 ~ 17.0
Magneto cover bolt 10 1.0
Muffler mounting bolt 18 ~ 28 1.8 ~ 2.8
Exhaust pipe bolt 18 ~ 28 1.8 ~ 2.8
Thermostat case bolt 10 1.0
Starter clutch bolt 23 ~ 28 2.3 ~ 2.8
M6 8 ~ 12 0.8 ~ 1.2
Cylinder head bolt
M 10 40 ~ 45 4.0 ~ 4.5
Cylinder head cover bolt 12 ~ 16 1.2 ~ 1.6
Cylinder head base bolt 8 ~ 12 0.8 ~ 1.2
Cylinder base nut 7 ~ 11 0.7 ~ 1.1
Engine pulley nut 130 ~ 160 13.0 ~ 16.0
Engine oil drain plug 21 2.1
Engine mounting nut 45 ~ 70 4.5 ~ 7.0
Engine mounting lock nut M 20 35 ~ 50 3.5 ~ 5.0
Engine mounting bolt 15 ~ 30 1.5 ~ 3.0
Spark plug 11 1.1
Cam chain tensioner bolt 8 ~ 12 0.8 ~ 1.2
Cam chain tensioner adjuster bolt 8 ~ 12 0.8 ~ 1.2
M6 11 1.1
Crankcase bolt
M8 26 2.6
Clutch sleeve hub nut 40 ~ 60 4.0 ~ 6.0
Primary drive gear nut 40 ~ 60 4.0 ~ 6.0
Camshaft housing bolt 12 1.2
Horn mounting bolt 8 ~ 12 0.8 ~ 1.2
◉ CHASSIS
ITEM N∙m kg∙m
Rear shock absorber mounting nut (Upper) 20 ~ 30 2.0 ~ 3.0
Rear shock absorber mounting bolt (Lower) 35 ~ 55 3.5 ~ 5.5
Rear pulley bolt 20 ~ 30 2.0 ~ 3.0
Rear axle bolt 90 ~ 140 9.0 ~ 14.0
Swingarm pivot nut 50 ~ 70 5.0 ~ 7.0
Swingarm pivot shaft 15 ~ 30 1.5 ~ 3.0
Swingarm mounting lock nut M26 70 ~ 80 7.0 ~ 8.0
Steering stem nut 80 ~ 100 8.0 ~ 10.0
Steering stem head nut 80 ~ 100 8.0 ~ 10.0
Front and Rear brake disk bolt 18 ~ 28 1.8 ~ 2.8
Front brake master cylinder mounting bolt 5~8 0.5 ~ 0.8
Rear brake master cylinder mounting bolt 18 ~ 28 1.8 ~ 2.8
Front and Rear brake caliper air bleeder valve 6~8 0.6 ~ 0.8
Front and Rear brake caliper mounting bolt 18 ~ 28 1.8 ~ 2.8
Front and Rear brake hose union bolt 20 ~ 25 2.0 ~ 2.5
Front axle bolt 50 ~ 80 5.0 ~ 8.0
Front axle pinch bolt 15 ~ 25 1.5 ~ 2.5
Front fork damper rod bolt 30 ~ 40 3.0 ~ 4.0
Front fork upper clamp bolt 22 ~ 35 2.2 ~ 3.5
Front fork cap bolt 30 ~ 40 3.0 ~ 4.0
Front fork lower clamp bolt 22 ~ 35 2.2 ~ 3.5
Front fork inner rod lock nut 17.5 ~ 22.5 1.75 ~ 2.25
Footrest mounting bolt 40 ~ 60 4.0 ~ 6.0
Frame down tube mounting bolt 22 ~ 35 2.2 ~ 3.5
Handlebar mounting bolt 40 ~ 50 4.0 ~ 5.0
SERVICE DATA
◉ VALVE + GUIDE Unit : mm (in)
ITEM STANDARD LIMIT
IN. 31.0 (1.22) ———
Valve diam.
EX. 25.5 (1.00) ———
IN. 0.1 ~ 0.2 (0.004 ~ 0.008) ———
Valve clearance (When cold)
EX. 0.28 ~ 0.32 (0.011 ~ 0.013) ———
IN. 0.020 ~ 0.047 (0.0008 ~ 0.0019) ———
Valve guide to valve stem clearance
EX. 0.030 ~ 0.057 (0.0012 ~ 0.0022) ———
Valve stem deflection IN. & EX. ——— 0.35 (0.014)
Valve guide I.D. IN. & EX. 4.500 ~ 4.512 (0.1771 ~ 0.1776) ———
IN. 4.465 ~ 4.480 (0.1758 ~ 0.1764) ———
Valve stem O.D.
EX. 4.455 ~ 4.470 (0.1754 ~ 0.1760) ———
Valve stem runout IN. & EX. ——— 0.05 (0.002)
Valve head thickness IN. & EX. ——— 0.50 (0.02)
Valve seat width 1.2 ~ 1.7 (0.047 ~ 0.067) ———
Valve seat angle IN. & EX. 45�
Valve head radial runout IN. & EX. ——— 0.03 (0.0012)
Inner ——— 36.8 (1.45)
Valve spring free length
Outer ——— 39.8 (1.57)
4.2 ~ 4.8kgf (9.3 ~ 10.6 lbs)
Inner. ———
at length 29.9mm (1.18 in)
Valve spring tension
17.0 ~ 19.6kgf (37.5 ~ 43.2 lbs)
Outer ———
at length 33.4mm (1.32 in)
◉ CYLINDER + PISTON + PISTON RING Unit : mm (in)

ITEM STANDARD LIMIT
Compression pressure 14kg/cm2 (at 500 rpm) 12 kg/cm2
Piston to cylinder clearance 0.045 ~ 0.075 (0.0018 ~ 0.0030) 0.120 (0.0047)
Cylinder bore 81.500 ~ 81.515 (3.2087 ~ 3.2093) 81.575 (3.2116)
81.440 ~ 81.455 (3.2063 ~ 3.2069)
Piston diam. 81.380 (3.2039)
(Measure at 20mm (0.79 in) from the skirt end)
Cylinder or cylinder head distortion ——— 0.05 (0.002)
1st Approx 9.9 (0.390) 7.9 (0.311)
Piston ring free end gap
2nd Approx 10.5 (0.413) 8.4 (0.330)
1st 0.20 ~ 0.35 (0.008 ~ 0.013) 0.5 (0.020)
Piston ring end gap (Assembly condition)
2nd 0.20 ~ 0.35 (0.008 ~ 0.013) 0.7 (0.028)
1st ——— 0.180 (0.007)
Piston ring to groove clearance
2nd ——— 0.150 (0.006)
1st 1.21 ~ 1.23 (0.0476 ~ 0.0484) ———
Piston ring groove width 2nd 1.01 ~ 1.03 (0.040 ~ 0.041) ———
Oil 2.01 ~ 2.03 (0.079 ~ 0.080) ———
1st 0.970 ~ 0.990 (0.0382 ~ 0.0390) ———
Piston ring thickness
2nd 1.170 ~ 1.190 (0.0461 ~ 0.0469) ———
Piston pin hole bore 20.002 ~ 20.008 (0.7875 ~ 0.7877) 20.030 (0.7886)
Piston pin O.D. 19.996 ~ 20.000 (0.7872 ~ 0.7874) 19.980 (0.7866)
◉ OIL PUMP
ITEM STANDARD NOTE
2
2.0 ~ 6.0 kg/cm
Oil pressure ———
(at 60 ℃, 3,000 rpm)
Oil pump reduction ratio 1.3 (45/34) ———
◉ CLUTCH Unit : mm (in)

ITEM STANDARD LIMIT
Clutch cable play 2 (0.08) ———
NO. 1 2.92 ~ 3.08 (0.115 ~ 0.121) 2.62 (0.103)
Drive plate thickness
NO. 2 3.42 ~ 3.58 (0.135 ~ 0.141) 3.12 (0.123)
NO. 1 15.9 ~ 16.0 (0.626 ~0.630) 15.1 (0.595)
Drive plate claw width
NO. 2 15.9 ~ 16.0 (0.626 ~0.630) 15.1 (0.595)
Driven plate distortion ——— 0.1 (0.004)
Clutch spring free length 54.2 (2.134) 51 (2.008)
◉ CAMSHAFT + CYLINDER HEAD Unit : mm (in)

ITEM STANDARD LIMIT
IN. 35.28 ~ 35.32 (1.389 ~ 1.391) 34.98 (1.377)
Cam height
EX. 33.38 ~ 33.42 (1.314 ~ 1.316) 33.08 (1.302)
Camshaft journal holder I.D. IN. & EX. 21.959 ~ 21.980 (0.8645 ~ 0.8654) ———
Camshaft journal oil clearance IN. & EX. ——— 0.15 (0.006)
Cylinder and cylinder head distortion ——— 0.05 (0.002)
Cylinder head cover distortion ——— 0.05 (0.002)
Cam chain pin (Arrow“3”) 16th pin ———
◉ CONROD + CRANKSHAFT Unit : mm (in)

ITEM STANDARD LIMIT
Conrod small end I.D. 20.006 ~ 20.014 (0.7876 ~ 0.7880) 20.040 (0.7890)
Conrod deflection ——— 3.0 (0.12)
Conrod big end side clearance 0.17 ~ 0.32 (0.007 ~ 0.013) 0.50 (0.020)
Conrod big end width 20.95 ~ 21.00 (0.825 ~ 0.827) ———
Crank web to web width 96.9 ~ 97.1 (3.815 ~ 3.823) ———
Crankshaft runout ——— 0.05 (0.002)
◉ TRANSMISSION + DRIVE BELT Unit : mm (in)

ITEM STANDARD LIMIT
Primary reduction ratio 2.09 (71/34) ———
Secondary reduction ratio 2.79 (78/28) ———
1st 2.46 (32/13) ———
2nd 1.78 (32/18) ———
Gear ratio 3rd 1.38 (29/21) ———
4th 1.13 (27/24) ———
5th 0.96 (25/26) ———
Shift fork to groove clearance 0.10 ~ 0.30 (0.004 ~ 0.012) 0.50 (0.020)
NO.1 & NO.2 4.85 ~ 5.00 (0.191 ~ 0.197) ———
Shift fork groove width
NO.3 4.85 ~ 5.00 (0.191 ~ 0.197) ———
NO.1 & NO.2 5.3 ~ 5.4 (0.209 ~ 0.213) ———
Shift fork thickness
NO.3 5.3 ~ 5.4 (0.209 ~ 0.213) ———
Type Poly chain belt ———
Drive belt Width 26 (1.02) ———
Pitch 11 (0.43) ———
When the rear tire is
4.5 ~ 5.5 (0.18 ~ 0.22) ———
Drive belt slack touched the ground
(4.5kg of Force) When the rear tire is not
5.0 ~ 6.0 (0.20 ~ 0.24) ———
touched the ground
Inner least 102 (4.02) ———
Bend capacity of drive belt
Back least 204 (8.04) ———
◉ CARBURETOR Unit : mm (in)

ITEM SPECIFICATION
Carburetor type BDSR39 TYPE(DOUBLE)
Bore size ф 39
Idle r.p.m. 1,300~1,500 rpm
Float height 7 (0.28)
Throttle cable play 0.5~1.0 (0.02 ~ 0.04)
FRONT REAR
Main jet (M.J.) 125 122.5
Main air jet (M.A.J.) 45 45
Jet needle (J.N.) 6DH64-53-3 6DH65-53-3
Needle jet (N.J.) P-OM P-OM
Pilot jet (P.J.) 20 20
Throttle valve (TH.V.) 95 95
#1 #2 #3 #1 #2 #3
By-pass (B.P.)
0.8 0.8 0.8 0.8 0.8 0.8
Valve seat (V.S.) 1.5 1.5
Starter jet (G.S.) 50 50
Pilot screw (P.S.) STD STD
Pilot outlet (P.O.) 1.0 1.0
PV. Stroke (P.V.) 30.7 30.7
◉ THERMOSTAT + COOLING FAN + COOLANT

ITEM STANDARD LIMIT
Valve opening 88℃
Thermostat valve operating temperature Valve full open 100℃
Valve closing 83℃
Thermostat valve lift Over 8mm /100℃
60℃ Approx. 125Ϊ
85℃ Approx. 48.5Ϊ
Engine coolant temperature sensor resistance
110℃ Approx. 24Ϊ
125℃ Approx. 15Ϊ
OFF→ON Approx. 95℃
Cooling fan thermo-switch operating temperature
ON→OFF Over 88℃
Use an antifreeze/coolant compatible with
Engine coolant type aluminum radiator, mixed with distilled
water only, at the ratio of 50 : 50
Reserve tank side 230㎖
Engine coolant capacity Radiator side 430㎖
Engine side 940㎖
◉ ELECTRICAL Unit : mm (in)

ITEM STANDARD NOTE
Ignition timing BTDC 5�/1,500rpm
Type CR8E
Gap 0.7~0.8 (0.028 ~ 0.032)
Spark plug Hot type CR7E
Standard type CR8E
Cold type CR9E
Spark performance Over 8mm (0.32)
Primary 3.5 ~ 5.5 Ϊ
Ignition coil resistance
Secondary 20 ~ 31 ㏀
Pick-up coil 80 ~ 120 Ϊ G-L
Magneto coil resistance
Charging coil 0.4 ~ 0.9 Ϊ Y-Y
Magneto no-load voltage Over 70V / 5,000 rpm
Battery standard charging voltage 13.5 ~ 15.0V / 5,000 rpm
Type STX14-BS
Capacity 12V 12Ah
Battery
Standard elec-
1.320 at 20℃ (68℉)
trolyte S.G.
Main 30A
Fuse size
Head lamp 15A
◉ WATTAGE Unit : W
ITEM SPECIFICATION
HI 60W
Head lamp
LO 55W
License plate lamp 5W
Brake / Tail lamp LED type
Turn signal lamp 10W×4
Neutral indicator lamp VFD type
Turn signal indicator lamp (Right & left) VFD type
High beam indicator lamp VFD type
※ LED : Light Emitting Diode

VFD : Vacuum Fluorescent Display
CAUTION
Do not use except the specified bulb (Wattage).
◉ SUSPENSION Unit : mm (in)

ITEM STANDARD LIMIT
Front fork stroke 130 (5.12) ———
Front fork spring free length 470 (18.5) ———
Front fork oil type TELLUS #32 ———
215mm (8.5 in) from end of outer tube
Front fork oil level (when maximum compressed without spring) ———
Front fork oil capacity (each leg) 420cc ———

Rear wheel travel 90 (3.54) ———
Swingarm pivot shaft runout ——— 0.6 (0.024)
Rear shock absorber pre-load position 1 / 5 position ———
Rear shock absorber spring length 223 (8.78) ———
STANDARD FRONT FORK DAMPING FORCE

Rebound Compression
Softer Turn to“S”direction Turn to“S”direction
Solo riding Standard 3 clicks out from end of“H”direction End of“S”direction
Stiffer Turn to“H”direction Turn to“H”direction
Dual riding 3 clicks out from end of“H”direction 2 clicks out from end of“S”direction
◉ BRAKE + WHEEL Unit : mm (in)

ITEM STANDARD LIMIT
Rear brake pedal height 408 (16.1) [when one person riding from the ground] ———
Front 4.0 (0.16) 3.0 (0.12)
Brake disk thickness
Rear 4.3 (0.17) 3.0 (0.12)
Brake disk runout Front∙Rear ——— 0.3 (0.012)
Front 15.870 ~ 15.913 (0.6248 ~ 0.6265) ———
Master cylinder bore
Rear 12.700 ~ 12.743 (0.5000 ~ 0.5017) ———
Front 15.827 ~ 15.854 (0.6227 ~ 0.6242) ———
Master cylinder piston diam.
Rear 12.657 ~ 12.684 (0.4983 ~ 0.4994) ———
Brake caliper cylinder bore Front∙Rear 25.4 (1.00) ———
Brake caliper piston diam. Front∙Rear 25.4 (1.00) ———
Front DOT3 or DOT4 ———
Brake fluid type
Rear DOT4 ———
Axial ——— 2.0 (0.08)
Wheel runout
Radial ——— 2.0 (0.08)
Front ——— 0.25 (0.01)
Wheel axle runout
Rear ——— 0.25 (0.01)
Front 120/70 - ZR 18 59W ———
Tire size
Rear 180/55 - ZR 17 73W ———
Front J18×MT3.50 ———
Wheel rim size
Rear J17×MT5.50 ———
◉ TIRE PRESSURE
NORMAL RIDING
COLD INFLATION
SOLO RIDING DUAL RIDING
TIRE PRESSURE
kPa kg/㎠ psi kPa kg/㎠ psi
FRONT 221 2.25 33.0 221 2.25 33.0
REAR 245 2.50 36.0 285 2.90 42.0
◉ FUEL + OIL
ITEM SPECIFICATION NOTE
Gasoline used should be graded 91 octane or higher.
Fuel type
An unleaded gasoline is recommened.
Fuel tank capacity 16 ℓ
Engine oil type API Over SL (SAE 10W/40)
Change 3,000 ㎖
Engine oil capacity Filter change 3,200 ㎖
Overhaul 3,400 ㎖
WELD CLAMP
L/WIRE BATTERY PLUS
STARTER RELAY PART
ENGINE EARTH (L/WIRE BATTERY MINUS)
IGNITION S/W
※ Install to the order RELAY (3EA) 36618-30610
WELD CLAMP
TAIL & STOP LAMP
LICENSE LAMP
RR TURN LAMP R/L
WELD CLAMP
WIRE AND CABLE ROUTING
BATTERY
WIRING HARNESS
SPEEDOMETER
HANDLE S/W Lh WELDING CLAMP
WELD CLAMP(#1) WELD CLAMP(#1)
REGULATOR WELDING CLAMP
WELD CLAMP TAPPING OF INSTALLATION BASIS
RR IGNITION COIL
COUP. FUEL GAUGE
COUP. WATER TEMP GAUGE
09407-20406
HANDLE S/W Lh
CLUTCH LEVER S/W
SPEEDOMETER
TAPPING OF INSTALLATION BASIS

WELD CLAMP HORN NOISE FILTER
COUP. HANDLE S/W Lh HARNESS, WIRING WELD CLAMP(#1)
COUP. SPEEDOMETER WELD CLAMP (#1) 09407-14403 WIRING HARNESS
HARNESS WIRING HARNESS DIODE (2EA)
REGULATOR DIODE, HAZARD
TURNSIGNAL RELAY MAGNETO RELAY (3EA)
GEAR POSITION S/W DIODE, S/STAND
COUP. RADIATOR FAN (VINYL TUBE)
COUP. FUEL GAUGE
09407-20406 LICENSE LAMP
09404-08403 REFLEX REFLECTOR RR

WELD CLAMP
WELD CLAMP
L/WIRE RR COMBI
REFLEX REFLECTOR SIDE RR (2EA)

(Exception of the application vehicle of European law)
09407-20406
WELD CLAMP
MAGNETO
HARNESS
GEAR POSITION S/W
RADIATOR FAN
L/WIRE, SPEED SENSOR

WELD CLAMP
THERMO SWITCH
NEUTRAL S/W
COUP. S/STAND
SIDE STAND S/W
09407-20406
HANDLE S/W Rh
COUP. HANDLE S/W Rh

Install inside of HEAD LAMP HOUSING
WELD CLAMP
HARNESS
STARTER RELAY
IGNITION S/W
RR BRAKE S/W
L/WIRE WATER TEMP GAUGE STARTER RELAY COUP. IGNITION S/W
BATTERY MINUS BATTERY PLUS

WELD CLAMP
IGNITOR
LOCK STEERING
IGNITION S/W
A
WELD CLAMP
RR BRAKE S/W
RR BRAKE S/W
09407-20406
L/WIRE, STARTER MOTOR
HOSE, THEMOSTAT BYPASS
L/WIRE STARTER MOTOR

09407-20406 09407-20406
HANDLE S/W
HANDLE S/W
B CLUTCH LEVER S/W
09407-20406 09407-20406
COUP. HANDLE S/W Lh
09404-06405 WIRING HARNESS

L/WIRE, FT TURN R/L
L/WIRE, C/LEVER S/W FT TURN L
FT TURN R HEAD LAMP COUP.
09407-20406
L/WIRE BATTERY MINUS

FRONT
CRANK CASE R
VIEW A
(ENGINE EARTH INSTALLATION DIRECTION)
VIEW Ｂ
TOP
PIPE FRAME Lh
WIRING HARNESS
SIDE L
"#1" MARK WELDING CLAMP PARTS (3EA)

FRONT CYLINDER REAR CYLINDER
CAUTION FOR HIGHTENTION CORD INSTALLATION DIRECTION
FRAME
WIRING HARNESS
WELD CLAMP
WELDING CLAMP OPERATION METHOD

HANDLE SWITCH Rh
STARTER RELAY WATER TEMP GAUGE THERMO S/W
E/G STOP HAZARD START FRONT BRAKE OFF
IGNITOR TURN FT IG. FAN MOTOR SIDE STAND HEAD LAMP
STOP OFF FREE FREE ON DIODE #2 DIODE#1
RUN ON PUSH ON RELAY COIL RELAY RELAY RELAY
FAN MOTOR
CLUTCH LEVER S/W DIODE #3

STARTER MOTOR
FREE
ON IGNITION S/W STOP LAMP S/W
OFF ON
ON OFF
WIRING DIAGRAM
RR TURN R
FT TURN R
TAIL & STOP
HEAD LAMP
POSITION LAMP LICENSE PLATE
FT TURN L RR TURN L
12V(12Ah)
REC & REG EARTH FUSE BOX FUSE BOX
SPEED N
BATTERY(MF) (15A) (30A)
SENSOR
ENG.
NEUTRAL S/W
L HI RR IG.
PUSH LO COIL OFF
R HORN ON
DIMMER
FRONT TURNSIGNAL UNIT FUEL GAUGE
FREE FREE
SIDE STAND S/W
SPEEDOMETER PUSH PUSH
HORN PASS MAGNETO
HANDLE SWITCH Lh
WIRE COLOR Br : Brown R : Red BR : Black with Red tracer YB : Yellow with Black tracer
B : Black O : Orange BW : Black with White tracer WR : White with Red tracer
Lg : Light green BG : Black with Green tracer WB : White with Black tracer L : Blue
Y : Yellow RW : Red with White tracer Gr : Gray W : White
RB : Red with Black tracer G : Green Sb : Light blue LW : Blue with White tracer
TAPPET SHIM SELECTION CHART (IN.)
SHIM No. 120 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220
MEASURING SHIM THICKNESS
TAPPET AT PRESENT
(mm) 1.20 1.25 1.30 1.35 1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20
CLEARANCE (mm)
0.00 ~ 0.04 1.20 1.25 1.30 1.35 1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10
0.05 ~ 0.09 1.20 1.25 1.30 1.35 1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15
0.10 ~ 0.20 Specified clearance - Adjustment unnecessary
0.21 ~ 0.25 1.30 1.35 1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20 2.20
0.26 ~ 0.30 1.35 1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20
0.31 ~ 0.35 1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20
0.36 ~ 0.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20
0.41 ~ 0.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20
0.46 ~ 0.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20
0.51 ~ 0.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20
0.56 ~ 0.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20
0.61 ~ 0.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20
HOW TO USE THE CHART
0.66 ~ 0.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20
1. Measure the tappet clearance.(When cold)
0.71 ~ 0.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20
2. Measure the shim thickness at present.
0.76 ~ 0.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20 3. Look for meeting space in that horizontal line
0.81 ~ 0.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20 for thickness and vertical line for clearance.
0.86 ~ 0.90 1.95 2.00 2.05 2.10 2.15 2.20
(EXAMPLE)
0.91 ~ 0.95 2.00 2.05 2.10 2.15 2.20 When the tappet clearance is 0.23mm and the
0.96 ~ 1.00 2.05 2.10 2.15 2.20 shim thickness at present is 1.70mm, the shim
1.01 ~ 1.05 2.10 2.15 2.20 thickness should be used 1.80mm.
1.06 ~ 1.10 2.15 2.20
1.11 ~ 1.15 2.20 HYOSUNG MOTORS & MACHINERY INC.
TAPPET SHIM SELECTION CHART (EX.)
SHIM No. 120 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220
MEASURING
SHIM THICKNESS
TAPPET AT PRESENT 1.20 1.25 1.30 1.35 1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20
(mm)
CLEARANCE (mm)
0.13 ~ 0.17 1.20 1.25 1.30 1.35 1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05
0.18 ~ 0.22 1.20 1.25 1.30 1.35 1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10
0.23 ~ 0.27 1.20 1.25 1.30 1.35 1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15
0.28 ~ 0.32 Specified clearance - Adjustment unnecessary
0.33 ~ 0.37 1.25 1.30 1.35 1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20
0.38 ~ 0.42 1.30 1.35 1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15
0.43 ~ 0.47 1.35 1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15
0.48 ~ 0.52 1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15
0.53 ~ 0.57 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15
0.58 ~ 0.62 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15
0.63 ~ 0.67 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15
0.68 ~ 0.72 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15
0.73 ~ 0.77 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 HOW TO USE THE CHART
0.78 ~ 0.82 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 1. Measure the tappet clearance.(When cold)
0.83 ~ 0.87 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2. Measure the shim thickness at present.
3. Look for meeting space in that horizontal line
0.88 ~ 0.92 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15
for thickness and vertical line for clearance.
0.93 ~ 0.97 1.85 1.90 1.95 2.00 2.05 2.10 2.15
0.98 ~ 1.02 1.90 1.95 2.00 2.05 2.10 2.15 (EXAMPLE)
When the tappet clearance is 0.35mm and the
1.03 ~ 1.07 1.95 2.00 2.05 2.10 2.15
shim thickness at present is 1.70mm, the shim
1.08 ~ 1.12 2.00 2.05 2.10 2.15
thickness should be used 1.75mm.
1.13 ~ 1.17 2.05 2.10 2.15
1.18 ~ 1.22 2.10 2.15 HYOSUNG MOTORS & MACHINERY INC.
1.23 ~ 1.27 2.15
Prepared by
1st Ed. JUL. 2005.
Manual No. 99000-51210

Printed in Korea

Hyosung GV650

Uploaded by

Copyright:

Available Formats

Hyosung GV650

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Hyosung GV650

Uploaded by

Copyright:

Available Formats

GV650(S/M)E-표지

HYOSUNG MOTORS & MACHINERY INC.

This manual contains an introductory description on

HYOSUNG MOTORS & MACHINERY INC.

� COPYRIGHT HYOSUNG MOTORS & MACHINERY INC. 2005.

Example : Front wheel

SYMBOL DEFINITION SYMBOL DEFINITION

Torque control required.

Apply oil. Use engine oil unless otherwise

Apply SUPER GREASE“A”. Measure in voltage range.

Apply SUPER GREASE“C”. Measure in resistance range.

Apply SILICONE GREASE. Measure in current range.

Apply MOLY PASTE. Use special tool.

Apply BOND“1215”. Use engine coolant.

Use fork oil.

INFORMATION LABELS ………………………………………………… 1- 1

WARNING / CAUTION / NOTE

SERIAL NUMBER LOCATION

◉ FRAME SERIAL NUMBER

◉ ENGINE SERIAL NUMBER

FUEL, OIL AND ENGINE COOLANT RECOMMENDATIONS

※ If an SAE 10W/40 motor oil is not available, select an

Use a premium quality 4-stroke motor oil to ensure

◉ FRONT FORK OIL

▣ WATER FOR MIXING

▣ LIQUID AMOUNT OF WATER/ENGINE COOLANT

Initial 800km Less than 1/2 throttle

◉ DIMENSIONS AND DRY MASS

PERIODIC MAINTENANCE SCHEDULE ………………………… 2- 1 2

LUBRICATION POINTS ………………………………………………… 2- 3

MAINTENANCE PROCEDURES …………………………………… 2- 4

SPARK PLUG …………………………………………………………… 2- 6

EXHAUST PIPE BOLTS AND MUFFLER MOUNTING BOLTS……… 2- 7

AIR CLEANER …………………………………………………………… 2- 8

FUEL HOSE ……………………………………………………………… 2-10

CLUTCH …………………………………………………………………… 2-10

ENGINE OIL ……………………………………………………………… 2-12

ENGINE OIL FILTER …………………………………………………… 2-14

DRIVE BELT ……………………………………………………………… 2-15

BRAKE SYSTEM ………………………………………………………… 2-17

STEERING ………………………………………………………………… 2-21

FRONT FORK …………………………………………………………… 2-21

REAR SUSPENSION …………………………………………………… 2-21

TIRE ………………………………………………………………………… 2-22

CHASSIS BOLTS AND NUTS ………………………………………… 2-22

ENGINE COOLANT ……………………………………………………… 2-23

RADIATOR HOSE………………………………………………………… 2-25

COMPRESSION PRESSURE …………………………………………… 2-26

OIL PRESSURE ………………………………………………………… 2-27

PERIODIC MAINTENANCE SCHEDULE

PERIODIC MAINTENANCE CHART

▣ FUEL TANK STAY

◆ USE OF FUEL TANK STAY

● Remove the fuel tank mounting bolt ②.

● Lift the rear end of the fuel tank and prop it up as

① Clutch lever holder and clutch cable ⑤ Speedometer gear box

● To inspect the front cylinder’s valve clearance, insert

Valve clearance Standard (When cold)

Thickness gauge : 09900-20806