1

Fly-Through-Computer
Flight Augmentation Computers

FAC 2 FAC 1
ELevator Aileron Computers

ELAC 2 ELAC 1
OR

SEC 3 SEC 2

Autopilot (Master FMGC)

SEC 1

Spoiler Elevator Computers

Fly-Through-Computer

FAC 2
FAC 1

ELAC 2 ELAC 1

SEC 3 SEC 2 SEC 1 SEC 1 & 2 provide backup THS and elevator control.
3

The flight control laws are the manufacturers built in computer instructions defining flight control movement, flight characteristics, and aircraft limitations. The flight control laws are a series of instructions that are executed by the flight control computers.

For safety and redundancy there are three flight control laws: NORMAL LAW ALTERNATE LAW DIRECT LAW Mechanical backup control of the THS and rudder is always available.
4

Flight Control Laws

LAW: A predetermined set of rules which govern flight characteristics

PITCH
FLIGHT CHARACTERISTICS

ROLL

YAW

PROTECTIONS

NORMAL LAW
The flight control law in use during normal operations when all, or nearly all, aircraft systems are operational.

Flight Control Laws

LAW: A predetermined set of rules which govern flight characteristics

=NORMAL=
FLIGHT CHARACTERISTICS

PITCH

ROLL

YAW

PROTECTIONS

=NORMAL=
Flight Characteristics

PITCH Load Factor Demand

Protections

LOAD FACTOR DEMAND

Neutral Stick Requests NO CHANGE in Gs

The flight control computers maintain approximately 1G Pitch attitude remains relatively constant.

A specific pitch input Aft Stick Requests a positive G CHANGE results in the same G The flight control computers order the elevators to move the required amount to provide the requested G change, change regardless of resulting in the nose pitching up. the current airspeed.
Forward Stick - Requests a negative G CHANGE
The flight control computers order the elevators to move the required amount to provide the requested G change, resulting in the nose pitching down. 9

=NORMAL=
Flight Characteristics

PITCH Load Factor Demand Automatic Pitch Trim

Protections

10

The Trimmable Horizontal Stabilizer (THS) is trimmed up or down to provide pitch trim.

The THS is a much more active part of the pitch control system on the Airbus than on many other aircraft. When a G change (pitch change) is commanded, the elevators initially move to provide the commanded change. If the desired pitch attitude requires the elevators to remain displaced, THS movement is commanded until the elevators are centered with the THS.

Pilot manual pitch trim inputs are not required.

11

=NORMAL=
Flight Characteristics

PITCH Load Factor Demand Automatic Pitch Trim

Ground Mode Flight Mode Landing Mode

Protections

12

GROUND MODE OF NORMAL LAW

A direct stick to flight control relationship exists. This enables the pilot to: Check the flight controls Rotate the aircraft for takeoff

13

FLIGHT MODE OF NORMAL LAW

Load factor demand in pitch All protections are available

14

LANDING MODE OF NORMAL LAW

The landing mode was created to give the flare and touchdown a conventional feel.

At 50 feet AGL (measured by the RAs) the ELACs memorize the pitch attitude At 30 feet AGL the ELACs add a gentle nose down command to the memorized pitch attitude, which the pilot counters with an aft stick input.

15

=NORMAL=
Flight Characteristics

PITCH Load Factor Demand Automatic Pitch Trim

Ground Mode Flight Mode Landing Mode

Protections

Maneuver Protection

16

Maneuver protection prevents aircraft damage due to overstressing the aircraft. The flight control computers prevent flight control surface movement that would cause the aircraft to exceed preset G limits.

NOTE: MAX = +2.0G IF FLAPS EXTENDED

NOTE: MAX = 0.0G IF FLAPS EXTENDED 17

=NORMAL=
Flight Characteristics

PITCH Load Factor Demand Automatic Pitch Trim

Ground Mode Flight Mode Landing Mode

Protections

Maneuver Protection Pitch Protection

18

NO FLY

30

15

NO FLY
19

=NORMAL=
Flight Characteristics

PITCH Load Factor Demand Automatic Pitch Trim

Ground Mode Flight Mode Landing Mode

Protections

Maneuver Protection Pitch Protection High Speed Protection

20

High speed protection prevents aircraft damage due to excessive speed.

Activates just above Vmo/Mmo

A gentle pitch up is produced by the flight control computers to limit further acceleration
High speed protection activation

VMO / MMO

Acceleration is limited even if full forward stick is applied. If high speed protection activates, automatic pitch trim in the nose down direction is deactivated and the autopilot, if engaged, disengages. It is always possible to overspeed the aircraft. The fight control computers merely limit the maximum attainable speed to within safe limits.
21

=NORMAL=
Flight Characteristics

PITCH Load Factor Demand Automatic Pitch Trim

Ground Mode Flight Mode Landing Mode

Protections

Maneuver Protection Pitch Protection High Speed Protection Angle of Attack Protection
22

Relative Wind

(ALPHA) = Angle of Attack = the angular difference between the relative wind and the attitude of the aircraft

23

= The angle of attack where the flight control computers intervene to prevent alpha from reaching a stall alpha. At Alpha Prot: Pitch command logic changes from load factor demand to commanding an angle of attack. Additional nose up trim is inhibited - nose down trim is still available. The autopilot, if engaged, disengages. A lowering of pitch attitude occurs.

VLS

Alpha Prot

If the pilot persists and pulls the stick further aft, eventually the angle of attack will reach . . . . . . . . .

24

= The highest angle of attack that the ELACs will allow. ALPHA MAX is a lower alpha than ALPHA STALL; therefore, it is nearly impossible to stall the aircraft in normal law.
NOTE: Although the FACs continuously compute the airspeeds corresponding with the various alpha protection values and display them on the airspeed tape, these speeds are for pilot reference only. The actual angles of attack that correspond with Alpha Prot and Alpha Max are computed by the ELACs based on angle of attack, not airspeed.

VLS

Alpha Prot Alpha Max

If autothrust is available, the airspeed is unlikely to reach Alpha Max because Alpha Floor will probably activate prior to reaching it.
25

Alpha Floor: Is a predictive function of the autothrust system. It activates based on the current trend if it predicts thrust will be required. Is normally available from immediately after takeoff throughout the flight down 100 feet RA in configuration 1 or greater.

Is only available in normal law.

26

Alpha floor uses the autothrust system to automatically provide TOGA thrust if Alpha is predictive and can be triggered at any airspeed; therefore it is any ofFloor the following conditions occur: Excessive high angles of attack.
NOT depicted on the airspeed tape. ItIndirectly is independent of Alpha Prot and Alpha Max. In other words, Alpha Floor as a result of windshear.

Excessive nose up attitudes combined with specific sidestick inputs.

Excessive high angles of attack
Indirectly as a result of windshear

can be triggered at airspeeds significantly higher than Alpha Prot.

Excessive high nose up attitudes combined with specific sidestick inputs

27

If Alpha Floor activates, TOGA thrust is automatically applied, regardless of thrust lever position. Alpha Floor activation DOES NOT require that autothrust be ENGAGED, but it must be AVAILABLE (i.e., operational).
A. FLOOR

28

Flight Control Laws

LAW: A predetermined set of rules which govern flight characteristics

=NORMAL=
FLIGHT CHARACTERISTICS

PITCH
Load Factor Demand Automatic Pitch Trim
Ground Mode Flight Mode Landing Mode

ROLL

YAW

PROTECTIONS

Maneuver Prot Pitch Protection Hi Speed Prot of Attack Prot

29

=NORMAL=
Flight Characteristics

ROLL Roll Rate

Protections

30

ROLL RATE
Neutral Stick Requests zero roll rate.
The aircraft essentially maintains the current bank angle.

Full Stick Deflection Requests 15 / sec

roll rate.

Stick Slightly Left / Right of Center - Requests a between 15 and 0 / sec roll rate.
31

=NORMAL=
Flight Characteristics

ROLL Roll Rate

Pitch Trim < 33

Protections

32

Automatic pitch trim is available up to 33 of bank to assist the pilot in maintaining altitude during turns.

Beyond 67 NO FLY Automatic pitch trim is available 33 to 67 33 to 67 Automatic pitch trim is available

0 to 33

0 to 33

33

=NORMAL=
Flight Characteristics

ROLL Roll Rate

Pitch Trim < 33
Bank Angle Hold < 33

Protections

34

If the stick is released to neutral, a 0 / second roll rate is commanded. The aircraft essentially maintains a constant bank angle, unless commanded otherwise.

Beyond 67 NO FLY Bank angle hold 0-33

33 to 67

33 to 67

Bank angle hold 0-33

0 to 33

0 to 33

35

=NORMAL=
Flight Characteristics

ROLL Roll Rate

Pitch Trim < 33
Bank Angle Hold < 33 Positive Spiral Stability > 33

Protections

36

If the bank angle exceeds 33 and the stick is released, bank angle returns to 33. This called positive spiral stability.
Positive spiral stability Beyond 67 NO FLY 33 to 67 33 to 67

0 to 33

0 to 33

NOTE: Positive spiral stability returns the bank angle to 0 if high speed protection is active.
37

=NORMAL=
Flight Characteristics

ROLL Roll Rate

Pitch Trim < 33
Bank Angle Hold < 33 Positive Spiral Stability > 33

Protections

BANK ANGLE PROTECTION

38

In normal, the flight control computes will not allow bank angles in excess of 67.

Bank angle protection

Beyond 67 NO FLY 33 to 67 33 to 67

0 to 33

0 to 33

NOTE: Bank angle is limited to 45 if high speed protection or angle of attack protection is active (the limit marks do not move).
39

Flight Control Laws

LAW: A predetermined set of rules which govern flight characteristics

=NORMAL=
FLIGHT CHARACTERISTICS

PITCH
Load Factor Demand Automatic Pitch Trim
Ground Mode Flight Mode Landing Mode

ROLL
Roll Rate
Pitch Trim Bank Angle Hold Pos Spiral Stab

YAW

PROTECTIONS

Maneuver Prot Pitch Protection Hi Speed Prot of Attack Prot

Bank Angle Protection

40

=NORMAL=
Flight Characteristics

YAW

Turn Coordination

Protections

41

ELAC 2 ELAC 1 FAC 2 FAC 1

Yaw orders associated with bank are processed by the ELACs then... transmitted to the FACs. The FACs direct the rudder to rudders hydraulic servos to move the rudder. Turn coordination is automatic, requiring no pilot rudder input. There is no rudder pedal movement resulting from turn coordination.
42

=NORMAL=
Flight Characteristics

YAW Turn Coordination Yaw Damping

Protections

43

YAW DAMPING

Yaw Damp Actuators

Two yaw dampers are installed. A yaw damper moves the entire rudder as necessary to dampen yaw oscillations.

Either yaw damper is capable of providing full yaw damping authority.

There is no rudder pedal movement resulting from yaw damping.

44

=NORMAL=
Flight Characteristics

YAW Turn Coordination Yaw Damping Rudder Trim

Protections

45

RUDDER TRIM
Rudder trim commands are sent from the FACs to one of two rudder trim motors which move the entire rudder surface. Trim tabs are not used. When an autopilot is engaged, rudder trim needs are computed by the FACs and automatically carried out. Manual rudder trim is deactivated. With the autopilots off, the rudder may be trimmed using the RUD TRIM knob on the pedestal.

As the rudder is trimmed (either manually or automatically), the rudder pedals ARE symmetrically displaced.
46

=NORMAL=
Flight Characteristics

YAW Turn Coordination Yaw Damping Rudder Trim Manual Rudder (HYD)

Protections

47

Mechanical Connection

Rudder Pedals

Backup mechanical control of the rudder is always available via cables from the rudder pedals to the rudder servos if at least one hydraulic system is available.

48

=NORMAL=
Flight Characteristics

YAW Turn Coordination Yaw Damping Rudder Trim Manual Rudder (HYD) Rudder Limiting

Protections

49

RUDDER LIMITING
The FACs, using airspeed inputs from the ADRs, limit rudder surface movement at high speeds to prevent excessive airframe loads and yaw responses.
The two rectangular symbols on the rudder travel indication represent the unrestricted rudder travel limit at low speeds.

The maximum rudder travel available at the current speed is indicated by small L shaped indications next to the rudder travel arc. Rudder PEDAL travel is never restricted. Only rudder SURFACE travel. NOTE: On some Spirit aircraft the high speed rudder travel limit depiction on the F/CTL page is fixed and does not move with changes in the rudder travel limit.
50

Flight Control Laws

LAW: A predetermined set of rules which govern flight characteristics x=NORMAL= ALTERNATE x
FLIGHT CHARACTERISTICS

PITCH
Load Factor Demand Automatic Pitch Trim
Ground Mode Flight Mode Landing Mode

ROLL
Roll Rate
Pitch Trim

YAW
Turn Coordination

Yaw Damping

Bank Angle Hold Rudder Trim Pos Spiral Stab Manual Rudder Rudder Limiting

PROTECTIONS

Maneuver Prot Pitch Protection Hi Speed Prot of Attack Prot

Bank Angle Protection

51

x ALTERNATE LAW x
A single failure WILL NOT cause the flight control system to degrade from NORMAL to ALTERNATE LAW.

A minimum of TWO or MORE failures must occur for the flight controls to degrade from NORMAL LAW, usually in the following systems:
Flight Control Computers
ELAC 2 ELAC 1 FAC 1 FAC 2 SEC 2 SEC 1

SEC 3

Hydraulic Systems

ADIRUs

A D

I R

A D

I R

A D

I R

52

x ALTERNATE LAW x
Two failures may not cause the flight control system to degrade.
For example:
ELAC 2 ELAC 1 FAC 1 FAC 2 SEC 2 SEC 1 SEC 3

The aircraft remains in normal law and the autopilots are operational.
53

x ALTERNATE LAW x
X X

F / CTL ALTN LAW (PROT LOST) MAX SPEED . . . . . . . . . . . . . . 320 KT

This statement is misleading.

54

Flight Control Laws

LAW: A predetermined set of rules which govern flight characteristics x ALTERNATE x
FLIGHT CHARACTERISTICS

PITCH
Load Factor Demand Automatic Pitch Trim
Ground Mode Flight Mode Landing Mode

ROLL
Roll Rate
Pitch Trim

YAW
Turn Coordination

Yaw Damping

Bank Angle Hold Rudder Trim Pos Spiral Stab Manual Rudder Rudder Limiting

PROTECTIONS

Maneuver Prot Pitch Protection Hi Speed Prot of Attack Prot

Bank Angle Protection

55

x ALTERNATE x

PITCH Load Factor Demand Automatic Pitch Trim

Flight Mode

Flight Characteristics

Protections

Maneuver Protection High Speed Protection Stability

Attack Protection Loof Speed Stability

56

Stabilities are flight control commands that smoothly attempt to change pitch to prevent an overspeed or a low speed (stall) condition. Pilots can manually override either stability with stick movement, causing an or a occur.

to

activates at a speed slightly below VMO/MMO. activates if the speed decreases to within a few knots of the stall warning.

57

Flight Control Laws

LAW: A predetermined set of rules which govern flight characteristics x ALTERNATE x
FLIGHT CHARACTERISTICS

PITCH
Load Factor Demand Automatic Pitch Trim
Flight Mode

ROLL
Roll Rate
Pitch Trim

YAW
Turn Coordination

Yaw Damping

Bank Angle Hold Rudder Trim Pos Spiral Stab Manual Rudder Rudder Limiting

PROTECTIONS

Maneuver Prot

Hi Speed Stab
Lo Speed Stab

Bank Angle Protection

58

Flight Control Laws

LAW: A predetermined set of rules which govern flight characteristics x ALTERNATE x
FLIGHT CHARACTERISTICS

PITCH
Load Factor Demand Automatic Pitch Trim
Flight Mode

ROLL ROLL DIRECT

A direct stick to flight control surface relationship in roll

YAW
Turn Coordination

Yaw Damping
Rudder Trim Manual Rudder Rudder Limiting

PROTECTIONS

Maneuver Prot

Hi Speed Stab
Lo Speed Stab
59

Flight Control Laws

LAW: A predetermined setMAN of rules which govern USE PITCH TRIM flight characteristics x ALTERNATE x DIRECT x x
FLIGHT CHARACTERISTICS

PITCH
Load Factor Demand Automatic Pitch Trim
Flight Mode

ROLL ROLL DIRECT

A direct stick to flight control surface relationship in roll

YAW
Yaw Damping

Rudder Trim
Manual Rudder Rudder Limiting

PROTECTIONS

Maneuver Prot

Hi Speed Stab
Lo Speed Stab

*Assuming a double FAC failure was

not the cause of the degradation.
60

x DIRECT LAW x
It is possible for the flight control system to degrade from NORMAL law straight to DIRECT law (e.g., dual radar altimeter failure). The primary reason that DIRECT law is reached is because the aircraft is in ALTERNATE law and the landing gear is lowered in preparation for landing. Why? Because ALTERNATE law does not provide a landing mode.

61

x DIRECT LAW x
DIRECT law results in a direct stick to flight control surface relationship. What does that really mean?

Stick inputs are still processed by the flight control computers and transferred to the flight control surfaces.
The computers, however, carry out pilot orders exactly as they are signaled. Unlike NORMAL or ALTERNATE laws, the computers have no authority to modify or override the stick inputs, thus NO protections OR stabilities are provided.

62

x DIRECT LAW x
USE MAN PITCH TRIM

This statement is more accurate.

F / CTL DIRECT LAW (PROT LOST) MAX SPEED . . . . . . . . 320 KT/ .77 MANEUVER WITH CARE USE SPEED BRAKE WITH CARE

No pitch or roll protections are provided in DIRECT law.

63

Flight Control Laws

LAW: A predetermined setMAN of rules which govern USE PITCH TRIM flight characteristics x DIRECT x
FLIGHT CHARACTERISTICS

PITCH
Load Factor Demand Automatic Pitch Trim
Flight Mode

ROLL ROLL DIRECT

A direct stick to flight control surface relationship in roll

YAW
Yaw Damping

Rudder Trim
Manual Rudder

Rudder Limiting

PROTECTIONS

Maneuver Prot

Hi Speed Stab
Lo Speed Stab
64

Flight Control Laws

LAW: A predetermined setMAN of rules which govern USE PITCH TRIM flight characteristics x DIRECT x
FLIGHT CHARACTERISTICS

PITCH PITCH DIRECT

A direct stick to flight control relationship in pitch.

ROLL ROLL DIRECT

A direct stick to flight control surface relationship in roll

YAW
Yaw Damping

Rudder Trim
Manual Rudder

Rudder Limiting

Manual THS Input

PROTECTIONS

65

Flight Control Laws

LAW: A predetermined setMAN of rules which govern flight characteristics MAN PITCH TRIM ONLY USE PITCH TRIM

Mech. Backup x DIRECT x

FLIGHT CHARACTERISTICS

PITCH PITCH DIRECT

A direct stick to flight control relationship in pitch.

ROLL ROLL DIRECT

A direct stick to flight control surface relationship in roll

YAW
Yaw Damping

Rudder Trim
Manual Rudder

Rudder Limiting

Manual THS Input

PROTECTIONS

66

Mechanical Backup
Mechanical backup control of the THS and rudder is always available. Mechanical backup is the only way to maintain aircraft control if all the flight control computers fail or there is a TOTAL loss of electrical power. It either occurs, the sidesticks are inoperative and the aircraft is controlled using the trim wheels, rudder pedals, and engine thrust. Mechanical backup provides a means of aircraft control until a higher law can be restored.

67

Mechanical Backup

F/CTL L + R ELEV FAULT MAX SPEED. . . . . . . . . . . 320/.77 - MAN PITCH TRIM . . . . . . . . USE - SPD BRK . . . . . . . . DO NOT USE

No ECAM message specifically indicates that mechanical backup is active.

68

Flight Control Laws

LAW: A predetermined set PITCH of rules which govern flight characteristics MAN TRIM ONLY

Mech. Backup
FLIGHT CHARACTERISTICS

PITCH

ROLL

YAW

PITCH ROLL MECHANICAL DIRECT

A Direct Stick to Flt Control Surface Relationship in Roll

Manual Rudder

Manual THS Input

PROTECTIONS

69

Flight Control Laws

LAW: A predetermined set PITCH of rules which govern flight characteristics MAN TRIM ONLY

Mech. Backup
FLIGHT CHARACTERISTICS

PITCH PITCH MECHANICAL

YAW YAW YAW MECHANICAL

Manual Rudder

Manual THS Input

PROTECTIONS

70

If extreme conditions cause the aircraft to leave the protected envelope (e.g. severe turbulence), and exceed a normal law limit, abnormal attitude law becomes active.

Abnormal attitude law is alternate law without protections and stabilities except for load factor protection.
This is a safety feature to ensure that the flight control computers never prevent the pilots from recovering from an abnormal attitude. After recovery, the flight controls remain in alternate law without protections but with auto trim. There is no reversion to direct law when the gear is extended.
71

Flight Control System Page

72

Flight Control System Page

X X X X X

X X X X X

XX

XX

XX

XX

XX

XX

73

74