Triumph Repair Manual 63 70

WORKSHOP MANUAL
UNIT CONSTRUCTION 650 C.c. TWINS

T120 TR6 & 6T FROM ENGINE No. DU.IOI
1963 to 1970
Copyright by
TRIUMPH ENGINEERING CO LTD
MERIDEN WORKS ALLESLEY . COVENTRY . ENGLAND
TELEPHONE MERIDEN 311 TELEGRAMS "TRUSTY" COVENTRY
See Bookmarks
ClassicBike.biz
ClassicBike.biz
ClassicBike.biz
This is the 't op of the line'
And with Triumph thai
means something, A really
responsive mount. Irs the
one that set. and stili holds,
the world's speed record,
A true champion in every
sense, the Bonneville is
greater than ever in '67 -
the smoothest ride on the
road, If you demand the
best motorcycle on the road
today, then your choice has
to be Bonneville. Available
either in the road sport
version for road riding or in
competition trim for the race
minded.
BONNEVILLE T120lR
BONNEVillE 650 C.c. O. H. V . TWIN CARBURETOR, TWIN CYLINDER.
Pride of ownershi p is built i nto this Triumph, Rugged good looks combine with complete dependabi lity for supreme rider satisfaction, A
modern, up to-date motorcycle with real quality features avai lable only on Triumph, such as polished stainless steel fenders that wil l never
lose their lusue, This is the greatest motorcycle under any and all road conditions, and it will take you (and a friend) where you want t o go
easily, quickly and comfortably, If you think that all motorcycli ng is the same. you owe it to yourself to test ride the new 1967 Bonneville that
IS wai ting for you at your nearest dealers now.
This is the 'top of the line'
And wi t h Triumph that
means something. A really
responSl\/e mount, It'S the
one that set, and sllil holds,
the world's speed record.
sense. the Bonneville is
greater than ever in '67 -
the smoothest tide on the
road. If you demand the
best motorcycle on the road
today, then your choice has
to be Bonneville. Available
minded.
2
BONNEVILLE T120lR
BONNEVILLE 650 c.c. O. H. V., TWIN CARBURETOR, TWIN CYLINDER.
Pride of ownership is bui ll Into this Tr iumph. Rugged good looks combine wi th complete dependabi lity for supreme rider satisfaction. A
modern, up to-date motorcycle with feal quality features available only on Triumph, such as polished stainless steel fenders that wi ll never
lose their lusue. This is the greatest motorcycle under any and all road conditions, and it will take you (and a friend) where you want to go
easily. qUickly and comfortably. If you think that all motorcycling is the same. you owe it to yourself to test ride the new 1967 Bonneville that
IS wai ting for you at your nearest dealers now.
FOR SPECIFI CATIONS NICAL DATA SEE P
This is the 'top of the line'
And with Triumph that
means something. A realty
responsive mount. Irs the
one that set and still holds,
the world's speed record,
sense, the Bonneville is
greater than ever i n ' 67 -
the smoothest ride on the
road. If you demand the
best motorcycfe on the road
today, then your choi ce has
to be Bonnevitte. Available
minded.
2
BONNEVILLE T120lR
BONNEVillE 650 C.c. O. H. V., TWIN CARBURETOR, TWIN CYLI NDER.
Pnde of ownership IS buil! IntO this Triumph. Rugged good looks combme with complete dependability for supreme rider satisfaction. A
modern, up to-date motorcycle with real quality features avaitable only on Triumph, such as polished stainless steel fenders that wi ll never
lose their Iusue. This is the greatest motorcycle under any and all road conditions. and it witt take you (and a friend) whele you want to go
easily, qUickly and comfortably. If you thtnk thai all motorcycling IS the same, you owe II to yourself to test ride the new 1967 Bonneville thai
IS waiting for you at your nearest dealers now.
ClassicBike.biz
ClassicBike.biz
THE BONNEVI LI E65O
The st andard by whi ch al l t he ot hers are
j udged.
A st reaml i ned
650cc hol ds t he AMA-approved worl d' s speed record of 245. 667 mph. Sol i d engi neeri ng,
rugged const ruct i on and t he ki nd of ri de t hat has t o be f el t t o be bel i eved.
The Bonnevi l l e i s i n a cl ass al l by i t sel f .
Speci f i cat i ons subj ect t o change wi t hout not i ce.
re@
Engi ne type OHV Front chai n si ze . 357 x . 225 x. 25 i n. Dupl ex
Number of cyl i nders 2 Rear chai n si ze . 625x. 375 i n.
Bore and st roke 7I x 82 mm, 2. 79 x 3. 23 i n. Ti re, f ront 3. 25 x 19 i n.
(K70)
Di spl acement 649 cc,40 cu. i n. Ti re, rear 4.00 x 18 i n. (K70)
Compressi on rati o 9:1 Brake di ameter, front 8 i n.
BHP and RPM 52
@
6, 500 Brake di ameter, rear 7 i n.
Engi ne sprocket teeth 29 Fi ni sh Ast ral Red/ Si l ver
Cl utch sprocket teeth 58 Seat hei ght 30. 5 i n.
Gearbox sprocket teeth 19 Wheel base 55. 5 i n.
Rear sprocket teeth 46 Length 84.5 i n.
RPM 10 mph top
gear 634 Wi dth 27 i n.
Gear rati os, top 4.84 Cl earance 7.125 i n.
Gear rat i os, t hi rd 5. 76 Wei ght (Dry) 386l bs.
Gear rati os, second 8.17 Fuel capaci ty 2.5 gal s.
Gear rat i os, f i rst 11. 81 Oi l capaci t y 6 pi nt s
Carburet or Twi n/ Amal 930
Tri umph West, P.O. Box 275, Duarte, Cal i f . 91010
sH-70-2
ClassicBike.biz
TRIUMPH 650 c.c. UNIT CONSTRUCTION TWINS
650 c.c. TRIUMPH BONNEVILLE 120 (T120)
ClassicBike.biz
TRIUMPH 650 C.C. UNIT CONSTRUCTION TWINS
650 CoCo (40 cu. in.) BONNEVILLE (T120R)
ClassicBike.biz
TRIUMPH 650 C.c. UNIT CONSTRUCTION TWINS
650 c.c. (40 cu. ;n.) TIGER 650 (TR6R)
ClassicBike.biz
TRIUMPH 650 C.c. UNIT CONSTRUCTION TWINS
650 c.c. (40 cu. in.) BON NEVILLE T.T. SPECIAL (T120TT)
DISCONTINUED AFTER ENGINE NUMBER DU. 66245
ClassicBike.biz
TRIUMPH 650 c.c. UNIT CONSTRUCTION TWINS
650 c.c. (40 cu. ins.) TROPHY (TR6R)
ClassicBike.biz

ClassicBike.biz

ClassicBike.biz

ClassicBike.biz

ClassicBike.biz
T120 BONNEVILLE-(cont)
CYLINDER BLOCK
Material
Bore size ...
Maximum oversize ."
Tappet guide bloc.k housing diameter
CYLINDER HEAD
Material
Inlet port size
Exhaust port size
Valve seatings:
Type
Material
VALVES
Stem diameter: Inlet
Exhaust ...
Head diameter: Inlet
Exhaust
Exhaust valve material
VALVE GUIDES
Material ...
Bore diameter (Inlet and exhaust)
Outside diameter (Inlet and exhaust)
Length: Inlet
Exhaust
GENERAL DATA
VALVE SPRINGS (RED SPOT INNER)
(GREEN SPOT OUTER)
Free length
Total number of coils
Total fitted load:
Valve open
Valve closed
Fitted length (valve closed):
Inner .. .
Outer .. .
VALVE TIMING
Set all tappet clearances @ -020 in. (-5 mm_) for checking
ROCKERS
Material
Bore diameter
Rocker spindle diameter
Tappet clearance (cold): Inlet
Exhaust
CAMSHAFTS
Journal diameter: Left
Right
Ojametral clearance: Left
Right
End float
Cam lift: Inlet and exhaust
Base circle diameter
TAPPETS
Material
Cast Iron
27948/27953 in.
2.8348/2-8353 in.
999 /9985 in.
D.T.D. 4H Aluminium
GO
1-h in. dia. tapering to 11 in.
1) in. dia.
Cast-in
Cast iron
3095;.3100 in.
3090/3095 in.
1-592/1-596 in.
1-434/1,440 in.
21/4NS
Aluminium-Bronze
'3127/"3137 in.
'5005/5010 in.
1* in.
2it in.
Outer
11 in.
St
Inlet
1431bs.
75 Ibs.
1,\ in.
1-h- in.
{
'n'et opens
Inlet closes
. Exhaust opens
Exhaust closes
Inner
1-H in.
7!
Exhaust
155 Ibs.
87 Ibs.
1. in.
l-h in.
34 before top centre
55 after bottom centre
55 before bottom centre
34 after top centre
High tensile steel forging
'5002/-5012 in.
4990/4995 in.
002 in. (05 mm.)
004 in. (-10 mm.)
8100/"8105 in.
8730 {8735 in.
0010/0025 in.
'0005/0020 in.
-013/020 in.
314 in.
-812 in.
High tensile steel body-Stellite
tip
Tip radius .__ 1125 in.
Tappet diameter '3110/'3115 in.
Clearance in guide block __ . ... ... 0005{0015 in.
Exhaust tappet has flat, -h in. tall. 1884 in./1881 in. below top of tappet, flat is -032 in. deep, and'oil hole is 047 in. diameter.
GD3
ClassicBike.biz
GO
T120 BONNEVILLE-(eant)
TAPPET GUIDE BLOCK
Diameter of bores
Outside diameter
Interference fit in cylinder block
CAMSHAFT BEARING BUSHES
Material
Bore diameter (fitted): Left
Right
Outside diameter: Left ...
Right
length: left inlet
Left exhaust
Right inlet and exhaust
Interference fit in crankcase: Left
Right
TIMING GEARS
Inlet and exhaust camshaft pinions:
No. of teeth ...
Interference fit on camshaft
Intermediate timing gear:
No. of teeth ...
Bore diameter
Intermediate timing gear bush:
Material
Outside diameter
Bore diameter
Length
Working clearance on spindle
Intermediate wheel spindle:
Diameter
Interference fit in crankcase
Crankshaft pinion:
No. of teeth ...
Fit on crankshaft
IGNITION TIMING
Crankshaft position (B.T.D.C.)
Static timing ...
Fully advanced
Piston position (B.T.D.C.)
Static timing ...
Fu"yadvanc;:ed
Advance range:
Contact breaker
Crankshaft
CONTACT BREAKER
Gap setting
Fully advanced at
SPARKING PLUG
Type
Gap setting
Thread size
GD4
GENERAL DATA
3120/3125 in.
10000/9995 in.
0005/-0015 in.
High density sintered bronze
-8125/8135 in.
874/875 in.
10010/10015 in.
1126/1127 in.
1104/1114 in.
932/942 in.
1010/1020 in.
001/002 in.
0010/0025 in
50
'000/-001 in.
47
'5618/-5625 in.
Phosphor bronze
5635/5640 in.
4990/4995 in.
'6775/6825 in.
0005/0015 in.
.4980/.4985 in.
.0005/.0015 in.
25
+ 0003/-0005 In.
060 in. (15 mm.)
415 in. (104 mm.)
12'
24'
'014-016 in. (35-40 mm.)
2,000 r.p.m.
Champion N3
025 In. (635 mm.)
14 mm. X I in. reach
ClassicBike.biz

ClassicBike.biz

ClassicBike.biz
GENERAL DATA GD
T120 BONNEVILLE-(cont)
FRAME AND ATTACHMENT DETAILS
HEAD RACES
No. of balls: Top ...
Bottom
Ball diameter
SWINGING FORK
Bush type ' ..
Bush bore diameter
Sleeve diameter... ...
Distance between fork ends
REAR SUSPENSION
Type
Spring details:
Fitted length
Free length ".
Mean coil diameter ...
Spring rate .. .
Colour code ... ...
load at fitted length
20
20
tin.
Pre-sized. steel-backed-
phosphor bronze
1+460/1+470 in.
14+45/1+450 In.
7t in.
Swinging fork controlled by com-
bined coil spring/hydraulic
damper units
8 in.
8,\ in.
11 in.
14S Ibs.Jin.
Blue/yellow
38 lb.
WHEELS, BRAKES AND TYRES
WHEELS
Rim size: Front and rear
Type: Front
Rear
Spoke details: Front: Left side
Right side
Right side
Rear: Left side
Right side
WHEEL BEARINGS
Front and rear, dimensions and type ...
Front and rear, spindle diameter (at bearing journals)
STANDARD REAR WHEEL
Bolt size for detachable sprocket
Number of bolu ...
Q.D. REAR WHEEL
Bearing type
Bearing sleeve: journal diameter
Brake drum bearing
Bearing sleeve: journal diameter
Bearing housing: internal diameter
REAR WHEEL DRIVE
Gearbox sprocket ...
Rear wheel sprocket teeth
Chain details:
No. of links: Solo
Sidecar
Pitch ...
Width
Speedometer drive gearbox ratio
Speedometer cable length
... WM2-19 FrontWM2-18 rear
... Spoke-single cross lacing
... ". Spoke-double cross lacing
20 off 8/10 SWG butted Si in. U.H. straight
10 off 8/10 SWG butted 4H in. U. H. 78
0
head
10 off 8/10 SWG butted 41 in. U.H. 100
0
head
20off8/10SWG butted 7 ..... in. U.H. 90
0
head
20 off 8/10 SWG butted 7. ih. U.H. 90 head
20X47x14 mm.-Ball Journal
7862/7867 in.
tin. dia.xti in. U.H.x26 C.E.I.
8
ix1ix-h in. Ball Journal
7500/7495 in.
t X 2 X -h in. Ball Journal
8745/8740 in.
19890/1-9980 in.
See "Gearbox"
46
104
103
i in.
.. in.
2:1
6S ins.
G07
ClassicBike.biz

ClassicBike.biz

ClassicBike.biz

ClassicBike.biz

ClassicBike.biz
GO GENERAL DATA
U.S.A. ONLY
TR6R, TR6C, T120R, T120TT (T120TT ONLY UP TO DU.66245)
FOR DATA NOT GIVEN HERE REFER TO GENERAL DATA FOR
MODELS T120 AND TR6
Compression ratio T120TT
Power output T120TT ...
CYLINDER HEAD Tt20TT
Inlet port size
Exhaust port size ...
Car-bureaer adaptors
CARBURETTERS
Choke size
Type
Main jet size
Pilot jet size
Needle jet size
Needle type
Needle position
Throttle valve
AIR CLEANER
THOR and T120TT
TR6R and TR6C
SPARKING PLUGS
T120TT
TACHOMETER DRIVE (TR6R, Tt20R)
Type of tachometer gearbox
Drive ratio ".
Cable length ...
Tachometer head
ENGINE
IGNITION TIMING (A.C, MAGNETO) TR6C AND Tl10TT (Up to DU6614S)
Static timing ...
Fully advanced
Static timing
Fully advanced
Advance range:
Contact breaker
Crankshaft
CONTACT BREAKER (A.C, MAGNETO) TR6C and TI10TT (Up to DU66l4S)
Gap setting
Advance range
Fully advanced at ...
TRANSMISSION
11 : 1
54 @ 6,5QO
1,\ dia. tapering to 1. in.
1i in. dia.
1,\ in. dia.
T120TT
1,.. in.
389/95
no
25
106
D
2
389/4
Coarse felt
Cloth
Champion NSSR
9 ~ drive (rom ljH end of exhaust
camshaft
4:1
28 in.
RSM 3003,01
tin, (63 mm,)
,.. in, (11.5 mm)
014/-016 in, (35/40 mm,)
50
2,000 R,P,M.
REAR CHAIN
T120TT ... 103 links
GEARBOX SPROCKET
TR6R
TR6C
T120R
T120TT
GD12
19 teeth
18 teeth
19 teeth
17 teeth
ClassicBike.biz
USA VARIATION5-(cont)
PETROL TANK
TR6R
TR6C, T120R, T120TT, TR6R
GENERAL DATA
FRAME
SUSPENSION UNITS TR6C, TR6R, T120R, T120TT
Spring details:
Fitted length
Free length ...
Mean coil diameter ...
Spring rate ...
Colour code ,_,
load at fitted length
REAR WHEEL NONQ,D.
Rim size
Tyre size ...
Secu rity bolt
TR6C and TI20TT only (Up to DU66245)
Oil restrictor assembly:
Rod diameter
Cup outer diameter
Body bore diameter
WHEELS
FORKS
3. galls. (4117 U.S. galls.)
2. galls. (2-912 U.S. galls.)
Sf in.
Sf in.
11 in.
100Ib/in.
Green/Green
28 lb.
WM318
400x18 in.
WM3
311S/312S in.
5845/5855 in.
590/592 in.
GO
N.B. With this hydraulic damping unit it Is essential that SAE 20 oil only is used.
TR6C and T120TT (Up to DU66245)
Alternator type ...
Horn, type
Coil type ...
Condensers (Capacitors)
Contact breaker type
lighting system:
Bulbs (6v.):
Headlight
Stop and tail light
Tail lamp type
Kill button type ...
HEADLAMP MCH 66
light unit diameter
Bulb, main .. .
Bulb, pilot .. .
TAIL LAMP
Type
Bulb ...
COILS, TR6R, TR6C, T120R
Type
ELECTRICAL
RM19E.T.
Clear hooter, A.C. 585, S.G.
3 E.T.
54441582
Lucas "leA
No. Type
Lucas 166
Lucas 384
...... 24/24 watts-Pre Focus
.. 6/18 watts-Offset pin
L679
... 151.SA SS5 up to DU66245
... SI in.
12 V. lucas 464 type 40/27 watt, vert-dip pre(ocus
12 V. lucas 989 type 6 watt, M.C.C.
... Type l679
12 V. Lucas 380 21,6 watt, S.B.C. offset pin
... Siba 32,000,1 or Lucas 17M12
GD13
ClassicBike.biz

ClassicBike.biz
GENERAL DATA
FRONT FORKS
TELESCOPIC FORK (Only applicable up to DU66245)
Oil restrieter assembly:
Rod diameter
Cup outer diameter
Body bore diameter
IGNITION CAPACITOR
Model
Storage life
CAPACfTIES
Fuel tank ,"
TACHOMETER
Type of tachometer gearbox
Drive ratio
Cable length
Tachometer head .. ,
ELECTRICAL SYSTEM
GENERAL
311513125 in.
58<1515855 in.
5901592 In.
2MC
GO
At 20'C. (68'F.) ,h.lf lif. 18
months
At 4O"C. (86"F.) shelf life 9 to 12
months
... 2! gall. (28 U.S. galls., 11 litres)
90 drive from ljH end of exhaust
camshaft
4: 1
28 in.
... RSM 3003101
GD15
ClassicBike.biz
GO
GENERAL DATA
GENERAL DATA
MISCELLANEOUS INFORMATION PRIOR TO ENGINE
NUMBER DU.66246
LUBRICATION SYSTEM
OIL PU MP (Befor-e DU44394 all models)
Scavenge bore diameter
Scavenge plunger diameter
OIL PUMP (DU44394 to DU.66245)
Scavenge bore diameter ...
Scavenge plunger diameter
Feed bore diameter
Feed plunger diameter ".
4372/4377 in.
4369/-4372 in.
'4877/-4872 in.
4872/4869 in.
3748(3753 in.
3747/,3744 in.
OIL PRESSURE RELEASE VALVE (with indicator button prior to DU13375)
Indicator spring length (free) -h in.
it in. Release spring length (free)
BASIC ENGINE DETAILS
6T up to DU44393
TR6 up to DU44393
THO up to DU24874
MAl N BEARI NG (All models up to DU24875)
Both ball journal
size
CRANKSHAFT LOCATION
All models DU101 to DU13374
All models DU13375 to OU24874
All models DU24875 onwards
FLYWHEEL (prior to DU24875)
Weight
Compression ratio I Combustion Power output
chamber capacity (b.h.p. @ r.p.m.)
--------1----
75 : 1 I 50 c.c. 37 @ 6,700
85 : 1 4J.J c.c. 40 @ 6,500
85 . 1 4J.J c.c. 46 @ 6,500
2+fx1ixtt in. ball journal
Located to timing side
Located to drive side
Located to timing side
... 8t Ibs.
PISTON CLEARANCES (Triumph pistons) before DU44394
Top of skirt
Bottom of ski rt
VALVES
Sizes
Inlet ...
Exhaust
VALVE SPRINGS
6T DU101 onwards
TR6 DU101 onwards
T120 DU101 to DU24874
T120 DU24875 to DU44394
GD16
6T (DU101-
DU5824)
6T (DU5825-
DU44393) TR6 T120
THon
(11 : 1 CR)
0088/0098 in. 0046/,0057 in. 0088/0098 in. 0093/0103 in. 0093/0103 in.
0033/0043 in. 0016/0027 in. 00ll/0043 in. 0038/0048 in. 0073/0083 in.
6T & TR6
DU101-
DU44393
1t in.
1H in.
T120
DU101-
DU5824
1t in.
1Hin.
Red spot
Red spot
White spot
Red spot
THO
DU5824
onwards
1tl in.
1",. in.
ClassicBike.biz
GENERAL DATA GO
MISCELLANEOUS DATA PRIOR TO ENGINE No. DU.66246-(cont)
VALVE SPRINGS (RED SPOT)
Free length ...
Total fitted load valve open
Total fitted load valve closed
VALVE SPRINGS (WHITE SPOT)
Free length
Total fitted load valve open
Total fitted load valve closed
VALVE TIMING
Set all tappets to
0-020 in. for checking
TAPPETS (T120 pr;or to DU24875)
Tip radius
6T
(DU10l
onwards)
Inlet opens 25 before top centre
Inlet closes sr after bottom centre
Exhaust opens 60 before bottom centre
Exhaust closes 17 after bottom centre
Outer Inner
11 in. 1# in.
5, 7;f
125 Ibs.
501b,.
Outer Inner
2n in. 1i in.
6, 7
130Ibs.
77 Ibs.
TR6 I THO T120
(DU101- (DU101. (certain later machines
DU44393) I DU24874) series DU24874 and
DU44393)
-----1-----------
W 34' 34"
55" 55" 55"
48" 48' 55'
2]0 2]0 34"
750 in.
CAMSHAFT 6T I TR6
Cam lift 305 in. 314 in. Inlet
296 in. Exhaust
(Certain later T120 between DU24875 and DU44393 have 314 in. both Inlet and Exhaust)
T120
314 in. Inlet
296 in. Exhaust
IGNITION TIMING AC. Magneto (E.T.) Ignition equipment
Static timing ...
Fully advanced
Static timing ...
Fully advanced
Advance range:
Contact breaker
Crankshaft
IGNITION TIMING
St t' {Crankshaft position DU101-DUS824
a IC Crankshaft position DU582S-onwards
FULLY ADVANCED
St t' {Piston position DU101-DU5824
a IC Piston position DU582S-onwards
Advance range:
Contact b r e k e r ~ U to DUS824 .. '
Crankshaft p
Contact breaker From DUS825 .. '
Crankshaft
CARBURETTER
Type
Main jet .. .
Needle jet .. .
Needle type
Needle position
Throttle valve
Pilot Jet
Bore
. ..
6T TR6
DU101 DU101-
onwards DU5824
376 376
230 250
106 106
C C
3 3
376/4 376/3t
25 25
1-h-in. 1-h- in.
29"
39"
tin. (63 mm.)
n in. (115 mm.)
5'
10'
6T TR6 THO
7 10
0
10"
W 14" 15
35' 39" W
, .
64 In. -h in. n in.
n in. nino nino
w w 14'
28 28' 28"
12' H' 12'
24" 24' 24'
TR6 THO THO
DU5825- DU10l- DU5825-
DU44393 DU5824 DU66246
389 376 389
310 240 260
106 106 106
D C D
1 2 3
389/3t 376/3t 389/3
15 25 25
1t in. 1-t& ir:. 1t in.
GD17
ClassicBike.biz

ClassicBike.biz
GENERAL DATA GO
MISCELLANEOUS DATA PRIOR TO ENGINE No. DU.66246-(cont)
FRONT FORKS
Engine Numbers and Model
DU10l-DU58H DU5825-DUI3374 DU13375-
STANCHIONS
Part Number
Length
One,\ in. Filler Hole
Damping Holes:-
Level from Bottom-51 in.
-4, in.
-3n- in.
-2,\ in.
-Ii In.
6T
HI123
20t in.
Yes
2 No. 42
holes
-
4-,\ in.
-
2 No. 42
TR6 6T
H1299 H1595
22,... in. 20i in.
No No
2 No. 42 2 No. 42
holes holes
- -
4-,\ in. 4-,\ in.
- -
2 No. 42 2 No. 42
TR6&T120
6T TR6 & T120 6T up to DU66245
H1695 HI6-49 H1890 HI889
22 in. 22 in. 22 in. 22 in.
Yes No Yes No
- - - -
2-,\ in. 2-,\ in.
- -
2-,\ in. 2-,\ in. 2-f.- in. 2-,\ in.
2-,\ in. 2-,\ in. 2,... in. 2-1. in.
2 No. 42 2 No. 42 2 No. 42 2 No. 42
To use 6T type stanchion where appropriate for TR6 or T120. solder up the filler hole.
Note:-No. 42 hole is 00935 in.
DAMPER SLEEVE
Length
Internal Diameter
TELESCOPIC FORK
Type
Spring details: Solo
Free length ...
No. of working coils
Spring rate ".
Colour code ...
Spring details: Sidecar
Free length ,_,
No. of working coils
Spring rate .. .
Colour code .. .
Bush details: Material
Length ...
Outer diameter
Inner diameter
Stanchion diameter ...
4,\ in.
Working clearance In top bush
Fork leg bore diameter ...
Working clearance of bottom bush
Fork legs: OU.101-0U.5824
DU.5825DU.66245 ...
Oil tank: DU.l0lDU.24814
3+1 in. 4ft in. 3. in. 3. in. 2. in. 2. in.
... 1-387/1-393 ins.
FRONT FORKS
Telescopic-Oil Damping
Eng. No. DU.l0l Eng. No. DU.5825 Eng. No. DU.I3375
to OU.5824 onwards to OU.66245
17,.. in.
52
32Ib./in.
Black/Green
18-h
58
37 Ib./in.
Red/white
CAPACITIES
~ i n
30Ib/in.
Unpainted
8i
15
37Ib/in.
Yellow/white
9t in.
12t
26t lb. in.
Yellow/blue
9t in.
15t
32t lb. in.
Yellow/green
Sintered bronze
Top bush Bottom bush
1 in. 870/875 in.
1-498/1-499 in. 1-4935/104945 in.
1-3065/13075 in. 12485/12495 in.
13025/13030 In.
0035/0050 in.
1-498/1500 In.
0035/"0065 in.
* pt. (150 ce.)
t pt. (190 ce.)
5 pt. (6 U.S. pints; 3 litres)
GD19
ClassicBike.biz
SECTION A
LUBRICATION SYSTEM
ROUTINE MAINTENANCE
TABLE OF RECOMMENDED LUBRICANTS
ENGINE LUBRICATION SYSTEM ...
CHANGING THE ENGINE OIL AND CLEANING THE OIL FILTERS
OIL PRESSURE
STRIPPING AND REASSEMBLING THE OIL PRESSURE RELEASE VALVE
STRIPPING AND REASSEMBLING THE OIL PUMP
REMOVING AND REPLACING THE OIL PIPE JUNCTION BLOCK
REMOVING AND REPLACING THE ROCKER OIL FEED PIPE
CONTACT BREAKER LUBRICATION
GEARBOX LUBRICATION ...
PRIMARY CHAINCASE LUBRICATION
REAR CHAIN LUBRICATION AND MAINTENANCE ...
GREASING THE STEERING HEAD BALL RACES
WHEEL BEARING LUBRICATION
TELESCOPIC FORK LUBRICATION
LUBRICATION NIPPLES
LUBRICATING THE CONTROL CABLES .. .
SPEEDOMETER CABLE LUBRICATION .. .
REAR BRAKE PEDAL SPINDLE LUBRICATION ...
CHECK PROCEDURE FOR WET SUM PING
Section
Al
A2
A3
A4
AS
A6
A7
A8
A9
Al0
All
A12
A13
A14
A1S
A16
A17
A18
A19
A20
A2l
A1
ClassicBike.biz
A LUBRICATION SYSTEM
SECTION AI
ROUTINE MAINTENANCE
Every 250 miles (400 Kms.)
Check level in oil tank
Check level in primary chaincase ...
Check chain oiler adjustment
Every 1,000 miles (1,600 Kms.)
Change oil in primary chaincase
Lubricate control cables
Grease swinging fork pivot ...
Remove rear chain for cleaning and greasing
Change engine oil
Every 2,000 miles
Lubricate the contact breaker
Check gearbox oil level
Check front forks for external oil leakage
Grease brake pedal spindle ...
Change oil in gearbox
Change oil in front forks ...
Grease wheel bearings
Grease steering head bearings
Section
A4
A12
A13
A12
A18
A17
A13
... A4
... A10
A11
A16
A20
A11
A16
A14
A15
ClassicBike.biz
LUBRICATION SYSTEM
FiB. AI. LUBRICATION CHART
Numbers in circles refer to right side of machine
Numbers in squares refer to left side of machine
GUIDE TO LUBRICATION POINTS
Illustration No. Description SAE Oil grade
1 Engine oil tank 20 or 50
2 Gearbox 50
3 Primary chaincase 20
4 Wheel hubs Grease
5 Steering head Grease
6 Brake cam spindle Grease
7 Brake pedal spindle Grease
8 Exposed cables 20
9 Telescopic fork 20 or 30
10 Swinging fork pivot Grease
11 Contact breaker cam Grease
All brake rod joints and pins 20
A
A3
ClassicBike.biz
SECTION Al
RECOMMENDED LUBRICANTS
UNITED KINGDOM
UNIT MOBIL B.P. CASTROL ESSO SHELL REGENT
Engine-Summer ... . .. Mobiloil A Energol SAE 30 Castrol XL Esse Extra Shell X-l00 30 Havoline SAE 30
-Winter ... ... Mobiloil Arctic Energol SAE 20W Castrolite Motor Oil Shell X-l00 Havoline
20W/30 20W SAE 20W
Gearbox ...
.. '
... Mobilube BP Gear Oil Castrol Hypoy Esso Gear Oil Shell Spirax Multigear
GX90 90EP 90EP GP90/l40 90EP EP90
Pri mary Chai "case ... Mobiloil Arctic Energol SAE 20 Castrolite Esse Extra Shell X-l00 Havoline
Motor Oil 20W /30 20W SAE 20W
Esso Extra Shell X-l00 Havoline
Telescopic Fork Mobiloil Arctic Energol SAE 20W Castrolite Motor Oil 20W SAE 20W
20W/30
Wheel Bearings ... ... Mobilgrease Energrease Castrolease Esse Shell Marfak
Swinging Fork ... ... M.P. L2 l.M. Multipurpose Retinax A Multipurpose 2
Steering Races ... ... Grease H
Easing Rusted Parts ... Mobil Energol Castrol Essa Shell Graphited
Spring Oil Penetrating Oil Penetrating Oil Penetrating Oil Donax P Penetrating Oil
OVERSEAS
TEXACO
UNIT MOBIL B.P. CASTROL ESSO SHELL (or REGENT)
Engine-Above 90F. ... Mobiloil AF Energol SAE 40 Castrol XXL Esso Extra Shell X-l00 40 Havoline 40
32'-90'F_ ... ... Mobiloil A Energol SAE 30 Castrol XL Motor Oil Shell X-l00 30 Havoline 30
Below lrF. ... MobiloH Arctic Energol Castrolite 20W/40 Shell X-l00 Havoline
SAE 20W 10W/30 20W 20-20W
Gearbox ... ... ... Mobilube BP Gear Oil Castrol Hypoy Esso Gear Oil Shell Spirax Multigear
GX90 90EP 90EP GP90/l40 90EP EP90
Primary Chaincase ... Mobiloil Artie Energol Castrolite Esso Extra Shell X-l00 Havoline
SAE 20W MotorOiI20W/40 20W 20-20W
Esso Extra Havoline 30
Telescopic Fork
. "
... Mobiloil Arctic Energol SAE 20W Castrolite Motor Oil Shell X-l00 Havoline
20W/40 20W 20-20W
Wheel Bearings, Swinging Mobilgrease Energrease Castrolease Esso Shell Marfak
Fork, Steering Races ... M.P. L2 l.M. MUltipurpose Retinax A All Purpose
Grease H
Easing Rusted Parts ... Mobil Energol Castrol Esso Shell Graphited
Spring Oil Penetrating Oil Penetrating Oil Penetrating Oil Donax P Penetrating
011
A4
ClassicBike.biz
-
'"
REAR CHAIN
FEED ADJUSTER
OIL
FILTER
SCAVENGE FEED TO ROCKER GEAR
SCAVENGE
PLUNGER
OIL PRESSURE - ~ T - - r
SWITCH
Fig. Al. Engine lubrication diagram
OIL DRAIN THROUGH
66 .. 0--___ CYLINDER BLOCK
AND PUSH ROD
Db COVERS TO SUMp
t"7\+-___ PISTON FED
BY SPLASH
CRANKCASE
BREATHER PIPE FROM
INLET CAMSHAFT
(ROTARY VALVE)
r-
C
all
:lll
n
~
o
z
ClassicBike.biz
SECTION A3
ENGINE LUBRICATION SYSTEM
The engine lubrication system is of the dry sump
type. The oil is fed by gravity from the oil tank to
the oil pump; the oil, under pressure from the oil
pump, is forced through drillings to the crankshaft
big ends, where it escapes, and lubricates the
cylinder walls, ball journal main bearings and the
other internal engine parts.
The oil pressure between the oil pump and crank-
shaft is controlled by the oil pressure release valve.
After lubricating the engine, oil falls to the sump
where it is scavenged through the sump filter, and
returned to the oil tank by the action of the oil
pump scavenge plunger. The oil pump has been
designed so that the scavenge plunger has a
greater capacity than the feed plunger; thus ensur-
ing that the sump does not become flooded.
Oil is fed to the valve operating mechanism by
means of the rocker oil feed pipe which is connected
to the scavenge return pipe just below the oil tank.
After travelling through the rocker spindles, the oil
Is fed into the rocker boxes and also passes through
drillings in the rocker arms onto the push rod end
caps, after which it falls by gravity down the push
rod cover tubes. The oil then passes through holes
drilled in the tappet guide blocks and into the sump,
where it is subsequently scavenged.
A positive oil feed is provided for the exhaust
tappets. The lubricant is ported through drillways
from the timing cover, and on through the crankcase
and cylinder block base flange to an annular groove
machined in the tappet guide block. Two oil holes
are provided in the groove to mate with the oil
holes in the tappets which provide a channel for
the lubricant to the tappet and camshaft working
faces. See Fig. A4 and Fig. AS. Current models use
tappets ground to provide a timing effect for the
lubricant.
SECTION A4
CHANGING THE ENGINE OIL AND CLEANING THE OIL FILTERS
The oil in new and reconditioned engines should be
changed at 250, 500 and 1,000 miles (400, 800 and
1,500 km.) intervals during the running-in period
and thereafter as stated in Section A1.
It is advisable to drain the oil when the engine is
warm as the oil will flow more readily. When
changing the oil it is essential that the oil filters are
thoroughly cleaned in paraffin (kerosene).
The hexagon-headed sump drain plug, which also
houses the sump filter, is situated underneath the
engine adjacent to the engine bottom mounting lug,
as shown in Fig. A3, reference No.4. Remove the
plug and allow the oil to drain for approximately
ten minutes. Clean the filter in paraffin (kerosene)
and re-fit the plug but do not forget the joint
washer.
The oil tank filter is screwed into the bottom of the
011 tank, the oil feed pipe is connected to it by means
of a union nut.
Remove the oil tank filler cap, place a drip tray
underneath the oil tank and remove the tank drain
A6
plug, where fitted, or alternatively unscrew the
union nut and disconnect the oil feed pipe. Allow
the oil to drain for approximately ten minutes.
Unscrew the large hexagon-headed oil tank filter
and thoroughly clean it in paraffin (kerosene).
It is advisable to flush out the oil tank with a flushing
oil (obtainable from most garages), or, if this is not
available, paraffin (kerosene) will do. However, if
this is used ensure that all traces are removed from
the inside of the oil tank prior to re-filling with
oil. (For the correct grade of oil see Section A2).
When re-fitting the oil tank filter do not forget the
fibre washer; and when connecting the oil feed pipe
union nut, care should be taken to avoid over-
tightening as this may result in failure of the union
nut. Replace the drain plug.
NOTE: The level in the oil tank should be
1-\- in_ (4 em,) below the filler cap, Further
addition of oil will cause excessive venting
through the oil tank breather pipe due to lack
of ai r space,
ClassicBike.biz
IIIIII11
LUBRICATION SYSTEM
III \31ll' .'.f
1\ ...... ---
" III))
iJ>
;J
Fig. A3. Underside view of enline/gearbox unit
,,;(
~ 5
/
Fig. A4. Tappet oil feed drill way Fig. AS. Tappet oil feed arrangement
A
EXHAUST
TAPPET
OIL FEED
DRllLWAY
A7
ClassicBike.biz
SECTION AS
OIL PRESSURE
The oil pressure is controlled by means ofthe release
valve situated at the front of the engine at the right
side adjacent to the timing cover.
When the engine is stationary there will be nil oil
pressure. When the engine is started from cold
pressure may be as high as 80 Ib./sq. in. reducing
when hot to a normal running figure of 65/80 Ib./
sq. in. At a fast idle when hot pressure should be
20/25 Ib./sq. in.
Pressure can only be checked with an oil gauge
connected to an adaptor replacing the oil pressure
on the front of the timing cover.
If satisfactory readings are not obtained, check the
followi ng:-
(1) That the oil pressure release valve is clean and
that the piston has the correct working
clearance in the valve body (see "GENERAL
DATA").
(2) That the oil tank level is not below minimum
and that oil is being returned to the tank.
(3) That the sump filter and oil tank filter are clean
and not blocked.
(4) That the oil pump is functioning properly and
that there is a supply of oil to the pump. Refer
to Sections A7 and A8 for checking the oil
pump and oil pipes with junction block
respectively.
(5) That the drillings in the timing cover are clean
and that the drillings in the crankcase connect-
ing the oil pipe junction block to the oil pump
are clear.
(6) That the oil seal in the timing cover which fits
over the crankshaft is not badly worn, thus
resulting in the oil escaping to the sump.
(7) That the big ends are not badly worn. Should
the big end bearings not have the correct
working clearance, the oil will escape more
readily. particularly when the oil is warm and
is more fluid, thus giving a drop in pressure.
Extensive periods of slow running (such as in heavy
traffic), or unnecessary use of the air control, can
cause dilution in the oil tank, and an overall drop
in lubricating pressure due to the lower viscosity
of the diluted oil.
Most lubrication and oil pressure troubles can be
avoided by regular attention to the recommended
oil changes.
SECTION A6
STRIPPING AND REASSEMBLING THE OIL PRESSURE RELEASE VALVE
The oil pressure release valve is very reliable and
should require no maintenance other than cleaning.
It is situated at the front of the engine on the right
side. adjacent to the timing cover.
Oil pressure is governed by the single spring
situated within the release valve body. When the
spring is removed it can be checked for compressive
strength by measuring the length. Compare this
figure with that given in "GENERAL DATA".
To remove the complete oil pressure release valve
unit from the crankcase, unscrew the hexagonal nut
AS
adjacent to the crankcase surface. When removed
the cap can then be unscrewed from the body thus
releasing the piston which should be withdrawn.
Thoroughly clean all parts in paraffin (kerosene) and
inspect for wear. The piston should be checked for
possible scoring and the valve body filter for possible
blockage or damage. To reassemble the release
valve unit offer the piston into the valve body and
screw on the valve cap with a new fibre washer.
Similarly. when screwing the release valve unit into
the crankcase. fit a new fibre washer between the
release valve body and the crankcase. See Fig. A6.
ClassicBike.biz
LUBRICATION SYSTEM A
1 Cap
2 Main spring
3 Piston
.. Fibre washer
S Valve body
6 Fibre washer
1
2
3 4
Fig. A6. Oil pressure release valve
Before engine number DU.13375 the two spring
type pressure release valve was used, this being
equipped with a pressure indicator button. See
Fig. A7
To dismantle, remove the complete valve and cap
as on later models. The main spring. auxiliary
spring, rubber sleeve and indicator shaft can be
removed from the valve cap by unscrewing the
brass shaft nut.
The oil seal cover in the valve cap should be levered
out and the seal replaced with a new one.
1 Indicator shaft
2 Cup
3 Rubber '0' ring
.. Valve cap
5 Rubber sleeve
6 Main spring
7 Auxiliary spring
8 Nut
9 Piston
10 Fibre washer
11 Valve body
12 Fibre washer
I 2 3 4
To reassemble the release valve unit, first press the
rubber seal and retaining cup into the valve cap,
place the sealing rubber on the button shaft (use a
small amount of oil) and, using the button shaft as a
guide, press the sealing rubber over the stub on the
inside of the valve cap. Now replace the button
shaft into its correct position and assemble the main
spring and auxiliary spring, finally screwing on the
brass shaft nut.
Reassembly should then be completed as for the
later type.
l!Ilr-
7 8 9 10
"
Fig. A7. Earlier oil pressure release valve
SECTION A7
STRIPPING AND REASSEMBLING THE OIL PUMP
The oil pump is situated inside the timing cover and
is driven by an eccentric peg on the nut fitted to the
end of the inlet camshaft. The only part likely to
show wear after considerable mileage is the oil
pump drive block slider. which should be replaced
to maintain full oil pumping effiCiency. The plungers
and pump body being constantly immersed in oil,
wear is negligible.
For removal of the timing cover see Section 832
The oil pump is held in its position by two conical
nuts. When these are removed the oil pump can
then be withdrawn from the mounting studs. The
scavenge and feed plungers should be removed and
the two square caps from the end of the oil pump
unscrewed. This will release the springs and bal/s.
All parts should be thoroughly cleaned in paraffin
(kerosene).
The plungers should be inspected for scoring. and
for wear by measuring their diameters and o m ~
paring them with those given in 'GENERAL DATA.
The springs should be checked for compressive
strength by measuring their lengths. Compare the
actual lengths with those given in "GENERAL
DATA.
ClassicBike.biz
Slider, 0 I
Drive Block ___
I. +--F"ed Plunger
Scavenge
Body--------tl
Intake Scavenge Port ---;o.Aii6t
Ball Valve
Scavenge Return Port
Ball, Pump Va'lve-----'
Spring, Ball
Body Plug-------'f
Fig. AB. Oil pump
Pressure
Feed Port
When reassembling the oil pump all parts should be
well lubricated and the oil pump finally checked for
efficiency by the following means:-
Place a small amount of oil in both bores (approxi
mately 1 c.c.) and press the plungers until oil is
forced through both outlet ports (these are the two
holes nearest the square caps (see Fig. AS). Place
the thumb over the intake ports (the holes neares.t
the plunger tops) and withdraw the plungers
slightly. If the oil level falls in either outlet port
then the ball valve is not seating properly and the
square caps should be removed and the cleaning
process repeated. On machines fitted with brass-
bodied oil pumps the ball valves can be tapped
lightly, but sharply into their seating to ensure an
efficient and adequate seal. Under no circumstances,
however. should this operation be attempted on a
pump body of cast iron material, where, if the ball
seating is distorted, the body must be renewed.
The aluminium drive block slider which fits over the
eccentric peg on the inlet camshaft nut should be
checked for wear on both the bore and in the plunger

When refitting the oil pump a new gasket should be
used and always remember that the cones of the
conical nut and washers fit into the countersunk
holes in the oil pump body.
When replacing the timing cover care should be
taken that the junction surfaces are cleaned prior
to application of the fresh coat of jointing compound
SECTION A8
REMOVING AND REPLACING THE OIL PIPE JUNCTION BLOCK
Drain the oil from the gearbox by removing the oil
drain plug situated underneath the gearbox as
shown in Fig. A3, reference No.3.
On earlier machines with rear enclosure panels,
remove the right panel by unscrewing two domed
nuts, a plain nut (just below the rear of the petrol
tank) and two front panel junction screws.
Remove the right-hand exhaust pipe, removing the
right footrest on earlier models, then remove the
gearbox outer cover as shown in Section D1.
Place a drip tray underneath the engine and remove
the drain plug where fitted, or, alternatively,
remove the flut securing the oil pipe junction block
A10
to the crankcase and allow the oil tank to drain for
approximately ten minutes.
Disconnect the rubber pipes from the oil tank,
remove the junction block and thoroughly clean It
in paraffin (kerosene).
Check the pipes for cuts and abrasions and that the
rubber connections are a good tight fit on the
junction block pipes. If there is any doubt about the
reliability of the rubber connectors, they should be
renewed.
Reassembly is the reversal of the above instructions
but remember to fit a new gasket between the
junction block and the crankcase.
ClassicBike.biz
Fig. A9. Oil pipe securing clips
When replacing the rubber connection tubes, care
must be exercised to prevent chafing the inside of
the rubber connections. Failure to observe this may
result in fragments of rubber entering the 011
system and causing blockage.
It is important to replace the screwed clips and
firmly clamp them in position.
SECTION A9
REMOVING AND REPLACING THE ROCKER OIL FEED PIPE
To disconnect the rocker oil feed pipe for removal.
the two domed nuts should be removed from the
ends of the rocker spindle. and the banjos with-
drawn.
Disconnect the rocker oil feed pipe from the oil
tank.
To free the rocker oil feed pipe from the frame it
may be necessary to disconnect several frame clips
from underneath the fuel tank. Care should be
taken that the pipe is not bent excessively as this
might ultimately result in a fracture. When
removed. the rocker oil feed pipe should be
thoroughly cleaned in paraffin (kerosene) and
checked for blockage by sealing the first banjo with
the thumb and first finger. whilst blowing through
the other. Repeat this procedure for the other
banjo.
When refitting the rocker oil feed pipe it i.
advisable to use new copper washers. but if the old
ones are annealed they should give an effective oil
seal. Annealing is achieved by heating to cherry red
heat and quenching in water. Any scale that is
formed on the washers should be removed prior to
re-fitting them.
SECTION AIO
CONTACT BREAKER LUBRICATION
The contact breaker is situated in the timing cover
and It Is imperative that no oil from the engine
lubrication system gets into the contact breaker
chamber. For this purpose there is an oil seal at
the back of the contact breaker unit pressed into
the timing cover. However slight lubrication of
the auto advance unit spindles is necessary. The
cam spindle is pre-lubricated with a preparation of
molybdenum disulphide and an epoxy resin. Liguid
lubricant must not be applied at this point since a
glutinous paste would be formed which would seize
the 'pindle and bearing.
A11
ClassicBike.biz

ClassicBike.biz
LUBRICATION SYSTEM
A
SECTION AI2
PRIMARY CHAINCASE LUBRICATION
The primary chaincase is lubricated by means of an
oil bath. To drain the oil, first remove the oil drain
plug from the bottom of the chaincase adjacent to
the left footrest. (See Fig. A3, reference No.2).
This plug also gives access to the chain tensioner.
To remove the plug on the earlier models it may be
necessary to loosen the left footrest. This can be
done by slackening off the footrest mounting bolt
and giving the footrest a sharp tap in a downwards
direction to release it from its locking taper. When
the plug is removed allow the oil to drain for
approximately ten minutes and replace the plug.
not forgetting the fibre washer. It is not necessary
to disturb the rotor cover during oil changing.
So that the correct amount of oil can be put into the
primary chaincase there is an oil level plug situated
at the rear underside of the chaincase. (See Fig. A3,
reference No.1). Alternatively, the correct level
can be achieved by using a measure of i pint
(350 c.c.) capacity.
o
/
OIL FILLER PLUG
Fresh oil can be put into the plug adjacent to the
cylinder barrel base or alternatively through the
clutch adjustment plug aperture which is in the
centre of the outer cover.
The primary chain is lubricated by means of a
collection chamber and oil feed pipe built into the
primary chain housing. The oil feed pipe directs a
continuous supply of oil at the point where the
chain runs onto the engine sprocket. To check this
for possible blockages it is necessary to remove the
primary chaincase outer cover, and remove the
front clip securing the oil feed pipe.
The oil ways can then be cleaned by a jet of com-
pressed air from such as a cycle pump. When
replacing the feed pipe clip ensure that the pipe is
parallel to the top portion of the chain and firmly
gripped by the clip.
The oil in the primary chaincase should be changed
as stated in Section A1.
PRI MARY CHAIN OIL FEED

o
CLUTCH ADJUSTER NUT
@{
o
o 0 0 0
c c
OIL LEVEL PLUG
o
CHAIN TENSIONER
ADJUSTER
OIL DRAIN PLUG
Fig. A12. Section through the primary chaincase
A13
ClassicBike.biz
SECTION AI3
REAR CHAIN LUBRICATION AND MAINTENANCE
The rear chain feed is taken from an oil junction
block situated in the neck of the oil tank (see
Fig. A 13). The rate of fiow of oi I to the chai n can be
controlled by a threaded tapered screw provided
in the oil junction block. The screw should be
turned clockwise to reduce the flow and anti-
clockwise to increase it. Earlier machines had firstly
an oil feed through a set metering jet at the back of
the primary chaincase and later the jet blanked off
completely. These latter machines would require
manual lubrication of the rear chain every 250 miles.
Disconnect the connecting link and remove the
chain. If available, connect an old chain to the end
of the chain being removed and draw it onto the
gearbox sprocket until the chain to be cleaned is
clear of the machine and can be disconnected.
Remove all deposits of road dust etc. by means of
a wire brush. Clean thoroughly in paraffin or
kerosene and allow to drain.
Inspect the chain for excessive wear of the rollers
and pivot pins and check that the elongation does
not exceed 1t%. To do this first scribe two marks
on a fiat table exactly 12i inches (3175 em.) apart.
place the chain opposite the two marks. When the
chain is compressed to its minimum free length the
marks should coincide with two pivot pins 20 links
apart. When the chain is stretched to its maximum
free length. the extension should not exceed i- in.
(625 mm.). If it is required to remove a faulty link.
or shorten the chain. reference should be made to
Section C11.
To lubricate the chain. immerse it into MELTED
grease (melt over a low flame. or, more safely, over
a pan of boiling water), and allow it to remain in the
grease for approximately 15 minutes, moving the
chain occasionally to ensure penetration of the
grease into the chain bearings. Allow the grease to
cool. remove the chain from the bath and wipe off
the surplus grease.
The chain is now ready for refitting to the machine.
NOTE: The connecting link retaining clip
must be fitted with the nose-end facing in the
direction of motion of the chain.
Fig. A13. Rear chain oil feed adjustment
SECTION AI4
GREASING THE STEERING HEAD BALL RACES
The steering head races are packed with grease on
assembly and require re-packing with the correct
grade of grease at the interval stated in Section A1.
Removal and replacement of the ball bearings is
comprehensively covered in the front fork section.
When the balls are removed they should be cleaned
in paraffin (kerosene). also. the cups fitted to the
A14
frame head lug and the cones fitted to the middle
lug stem should be cleaned thoroughly b)' means of
a paraffin (kerosene) soaked rag. then inspected for
wear, cracking or pocketing.
The fresh supply of grease should be utilised to hold
the balls in position in the cups whilst the fork is
assembled.
ClassicBike.biz
SECTION AIS
WHEEL BEARING
The wheel bearings are packed with grease on
assembly but require re-packing with the corree ..
grade of grease at the interval stated in Section A1.
The bearings on both the front wheel and rear wheel
should be removed, cleaned in paraffin (kerosene)
and assembled with the hubs well packed with the
LUBRICATION
correct grade of grease. For details concerning the
grade of grease to be used (which is the same for
both wheels), see Section A2.
R.:-omoving and replacing the bearings for the front
and rear wheels is comprehensively covered in
Section F8.
SECTION AI6
TELESCOPIC FORK LUBRICATION
The oil contained in the front fork has the dual
purpose of lubricating the stanchion bearing bushes
and also acting as the suspension damping medium.
Therefore it is imperative that the fork legs have
an equal amount of oil in them. On the current
shuttle valve fork it is important that only SAE 20
oil is used for lubrication purposes.
011 leakage at the junction between the stanchion
and bottom fork leg is prevented by means of an
oil seal. Ii there is excessive oil leakage at this
junction it may be necessary to renew the oil seal
(see Section G6), but before undertaking this work,
the fork should be checked to ensure that there is
the correct amount of oil in each of the fork legs.
The correct amounts are as follows:-
Engine No. DU.101-DU.582<\--i pint (150 c.c.)
Engine No. DU.5825 onwards, pint (200 c.c.)
In the case where an earlier model (i.e. DU.101-
DU.5824) has been fitted with longer fork legs, to
cater for the fitting of a sidecar, the correct amount
of oil is t pint (225 c.c.).
Particular attention should be given to the oil change
period. The fork should be drained and refilled with
the correct Summer or Winter grade of oil every
Spring and Autumn if the mileage covered is
less than the distance in Section A1.
To drain the oil from the fork legs remove the two
small hexagonal drain plugs adjacent to the left and
right ends of the front wheel spindle.
Oll can be expelled at a greater rate by compressing
the fork two or three times.
To refill the fork legs on earlier machines in-
corporating "Nacelle" eqUipment first replace the
drain plugs complete with fibre washers, then
slacken the headlamp securing screw adjacent to
the speedometer and withdraw the head/amp and
rim assembly.
Remove the two small hexagonal filling plugs from
the stanchions (these are located approximately
3 inches from the top lug and should be facing
forward towards the head lamp aperture) and pump
the advised amount of oil into each fork leg by
means of a pressure can or gun. For the recom-
mended grade of oil see Section A2.
When refitting the filler plugs do not forget the
fibre washers.
If a pressure can or gun is not available the method
recommended for filling the fork legs with oil Is
that of removing the cap nuts.
Access to the cap nuts can be gained by removing
the nacelle top cover (if fitted) and handlebar as
described in sections G1 and G3 respectively.
Then, by means of spanner D220, the hexagonal cap
nuts (1t inches across flats) can be unscrewed and
withdrawn. The correct amount of oil should then
be poured into each fork leg.
To refill the fork legs on machines fitted with sports
headlamp, the fork hexagonal cap nuts must be
unscrewed and Withdrawn, and the correct amount
of oil poured into each fork leg. This will necessitate
removal of the handlebar on machines with
reSiliently mounted handlebar eqUipment.
A15
ClassicBike.biz
SECTION AI7
LUBRICATION NIPPLES
Both the brake operating camshafts and the swinging
fork pivot bearings should be lubricated by means
of the lubrication nipples.
The brake camshafts have integral lubrication nipples.
Care should be taken that the surface of the nipple
is not damaged. Slight distortion may be removed
with a fine grade file.
The front and rear wheel brake cam and spindle
bearing surfaces should be sparingly lubricated with
the correct grade of grease (Section A2). This can
be done by giving the lubrication nipples on the ends
of the camshafts one stroke each from a grease gun.
However, if the grease does not penetrate, the
brake cams should be removed and cleaned
thoroughly in paraffin (kerosene). The cam bearing
surfaces should then be greased on reassembly.
SWINGING FORK PIVOT
The greasing nipple is situated centrally underneath
the swinging fork and should be given several strokes
with a high pressure grease gun until grease is
forced through each end of the pivot bearings or
past the end cap '0' ring seals on current machines.
If the grease does not penetrate then the pivot must
be removed to ensure adequate lubrication.
Removal of the swinging fork is detailed in section
E10. When the fork is removed the sleeves and
distance tube should be withdrawn and all parts
should be thoroughly cleaned out in paraffin
(kerosene) and allowed to drain.
Reassembly is a reversal of the above instructions.
The space surrounding the distance tube should be
carefully packed with the correct grade of grease,
and the sleeves should be well greased on their
bearing surfaces.
24
Fig. A14. Swinging fork pivot lubrication nipple
SECTION AI8
LUBRICATING THE CONTROL CABLES
The control cables can be periodically lubricated at
the exposed joints with a thin grade of oil (see
Section A2).
A more thorough method of lubrication is that of
feeding oil into one end of the cable by means of a
reservoir. For this, the cable can be either discon-
nected at the handlebar end only, or completely
removed.
A16
The disconnected end of the cable should be
threaded through a thin rubber stopper and the
stopper pressed into a suitable can
with a hole in its base. If the can is then inverted
and the lubricating oil poured into it through the
hole, the oil will trickle down between the outer
and inner cables. It is best to leave the cable in this
position overnight to ensure adequate lubrication.
ClassicBike.biz
SECTION AI9
SPEEDOMETER CABLE LUBRICATION
The speedometer cable should be lubricated by
means of grease (see Section A2 for correct grade).
It is not necessary to completely remove the cable.
but only to disconnect it from the speedometer
and withdraw the inner cable. To do this on nacelle
models first remove the headlamp unit by slackening
the securing screw adjacent to the speedometer on
the nacelle. Unscrew the union nut at the base of
the speedometer. withdraw the inner cable and
dean it in paraffin (kerosene). Smear the surface
with grease, except for 6 in. (1S cm.) nearest to the
speedometer head.
The cable is now ready to be offered into the outer
casing and excess grease wiped off. Care should be
taken that both "squared" ends of the inner cables
are located in their respective "square" drive
hOUSings before the union nut is tightened.
SECTION A20
BRAKE PEDAL SPINDLE LUBRICATION
The brake pedal spindle is bolted to the left rear
engine mounting plate. The spindle .should be
covered with a fresh supply of grease occasionally
otherwise corrosion and inefficient operation may
result.
To gain access to the spindle, slacken off the rear
brake rod adjustment, unscrew the brake pedal f\.,
retaining nut and withdraw the pedal. J
Remove any rust from the spindle with fine emery.
Clean the bore of the pedal and smear the spindle
with grease (see Section A2) prior to refitting.
Do not forget to replace the spring and plain washer
between the retaining nut and brake pedal. Fig. A15. Brake pedal spindle lubrication
A17
ClassicBike.biz
SECTION A21
CHECK PROCEDURE FOR WET SUMPING
'Wet sumping' or a lack of scavenge is a condition
which can occur due to a number of causes. The
symptoms of this condition are:-
(1) Excessive oil emitting from crankcase breather
tube and resulting high oil consumption.
(2) Smoking exhaust.
To verify that a wet-sumping condition exists, run
the engine until it is thoroughly warm. Within
five minutes after engine shutoff drain the sump.
Measure the amount of oil that drains out. An
amount of oil over 100 c.c. indicates a wet-sumping
condition and corrective measures should be taken.
POSSIBLE CAUSES OF WET-SUMPING
ARE
(1) Foreign material preventing ball valve from
seating in the scavenge side of oil pump (most
common cause).
(2) Poor check valve ball seat.
(3) Air leak in crankcase oil scavenge pipe.
(4) Air leak in oil pump to crankcase jOint.
(5) Porous crankcase casting.
(6) Air leak at E4539plug bottom of engine.
(7) Blockage in return oil pipe-could be caused
by mis-aligned E3763 oil junction block gasket.
(8) Oil pressure release valve piston in full bypass
position due to a stuck piston or broken or
missing spring.
(9) Restriction in oil tank vent pipe.
SCAVENGE SUCTION TEST (for checking
above causes numbers 1 to 6)
Obtain a vacuum gauge calibrated in inches of
mercury. Attach a length of standard Triumph
oil pipe to it and proceed as follows:
(1) Run engine until it is thoroughly warm.
(2) Remove the oil sump cap and screen.
(3) Connect hose from vacuum gauge to oil
scavenge pipe.
(4) Run engine at a fast idle-gauge should read a
vacuum of 18-26 inches of mercury. .
(5) Stop engine and observe gauge. The needle
should gradually-not immediately-drop to
zero.
A18
IF THE SCAVENGE SUCTION
TEST IS SATISFACTORY
(1) Check oil pressure relief valve assernbly and
also check oil pressure.
(2) Check the return system from the pump to the
oil tank and also the tank vent.
TO CHECK FOR A BLOCKED OR
RESTRICTED OIL RETURN TO
THE TANK
(1) On the oil tank using a hand brace or chuck and
nil and tl" drill bits, run the drill bits into the
return tube and rocker feed tube (if fitted)
at the bottom of the tank to see that both
tubes are free from internal burrs and res-
trictions that can occur at their welded joints.
(2) After doing the above, blowout the return
oil line and the return tube in the oil tank with
compressed air.
IF THE ABOVE TEST IS NOT
SATISFACTORY
(1) Remove oil pump-clean thoroughly and see
that ball seats are concentric and free from
pits or grooves. Re-assemble pump, tighten
check valve caps securely and re-install pump
with a new gasket.
To check for crankcase scavenge tube leakage or
case porosity, fill a good "pumper" type oil can
with light oil and squirt through a folded rag into
plckup tube. Back pressure could prevent pumping
oil out of the can in a few pumps. If the oil can
still be pumped with no evidence of substantial
back pressure, obviously there is a leak in the
the crankcase tube or crankcase scavenge oil
passageways.
To be sure that the oil can is satisfactory for this
test, fill it with light oil and block the outlet tube.
After one or two pumps the can should "liquid
lock". If the can can stil be pumped, the pump
mechanism is suffering from excessive blow-by and
the can will not suffice for this test.
ClassicBike.biz

ClassicBike.biz
B
ENGINE
FI,. at. Exploded view of 650 c.co en.lne learbox unit
82
ClassicBike.biz
ENGINE B
DESCRIPTION
The engine is of unit construction having two
aluminium alloy mating crankcase halves. the gear-
box housing being an integral part ofthe right half-
crankcase and the primary chain case an integral
part of the left half-crankcase.
The aluminium alloy cylinder head has cast in
Austenitic valve seat inserts, and houses the over-
head valves, which are operated by rocker arms
housed in detachable alloy rocker boxes. Four
aluminium alloy push rods operate the rocker arms,
which are each fitted with adjusters, accessible when
the rocker box Inspection caps are removed.
The aluminium alloy die cast pistons each have
two compression rings and one oil scraper ring. The
connecting rods are of H Section in RR56 Hidu-
mlnium alloy, with detachable caps, and Incorporate
steel-backed renewable "shell" bearings. Each of
the connecting rod caps is machined from a steel
stamping and held in position by means of two high
tensile steel bolts, which are tightened to a pre-
determined extension figure to give the correct
working clearance of the bearings on the crankshaft
journals.
The inlet and exhaust camshafts operate In slntered
bronze bushes which are housed transversely in the
upper part of the crankcase. The inlet and exhaust
camshafts are driven by a train of timing gears from
the right end of the crankshaft. The Inlet camshaft
also operates the oil pump and rotary breather valve
disc, whilst the exhaust camshaft drives the adjust-
able contact breaker, which Isfittedwlth an automatic
advance and retard unit, and the tachometer
gearbox (when fitted).
The two-throw crankshaft has a detachable shrunk-
on cast-iron flywheel which is held in position by
three high tensile steel bolts, locked by the use of
"TRIUMPH LOCTITE" sealant and tightened to a
pre-determined torque figure.
The big end bearings are lubricated at pressure with
oil which travels along drillings in the crankcase
and crankshaft from the double plunger oil pump:
oil pressure in the lubrication system is governed
by means of the oil pressure release valve situated
at the front of the engine, adjacent to the timing
cover.
The cylinder barrel is made from a high-grade cast-
iron and houses the press-fit tappet gUide block .
Power from the engine is transmitted through
the engine sprocket and primary chain to the
shock absorbing clutch unit and four speed gearbox.
Primary chain tension is governed by an adjustable
rubber-pad chain tensioner which is immersed in
the primary chain oil bath.
The electrical generator set consists of a rotor,
which is fitted to the left end of the crankshaft, and
an encapsulated six coil stator which is mounted on
three pillar bolts inside the primary chain housing.
Carburation is by twin Amal carburetters with
integral float chamber. The TR6 and earlier 6T
have only one such instrument.
B3
ClassicBike.biz
B ENGINE
SECTION BI
REMOVING AND REPLACING THE ENGINE UNIT
Turn the fuel tap to the "OFF" position and dis-
connect the feed pipes. Cut the fuel tank bolt-
securing wire. then unscrew three fuel tank
mounting bolts. Raise the fuel tank at the rear to
remove it. On earlier models with the nacelle type
head lamp the two rear nacelle securing screws will
have to be removed to gain sufficient clearance for
tank removal.
Remove the fuse from the holder or on earlier
models disconnect the leads from the battery ter-
minals and remove the "Lucar" connectors from
the left and right ignition coils. Remove the top
and bottom coil mounting bolts and distance pieces.
The ignition coils will then be free to be removed.
Care should be taken not to damage the light
alloy casing of the ignition coils: indentations
caused to the outer casing may ultimately
result in ignition failure.
Unscrew the four nuts securing the torque stays
to the cylinder head and remove the front and rear
torque stay mounting bolts and distance pieces,
then remove the torque stays.
Disconnect the speedometer cable from underneath
the speedometer and remove any necessary frame
clips so that the cable is free. On models of the
nacelle type the head lamp unit will have to be re-
moved to gain access to the underside of the speed-
ometer. To do this, slacken the screw in the head-
lamp rim, adjacent to the speedometer dial. then
carefully lever off the headlamp unit.
Disconnect the tachometer cable (if fitted) by
unscrewing the union nut at the right angled drive
gearbox shown in Fig. B2.
On earlier machines that are fitted with rear en-
closure panels, remove the two front panel junction
screws and unscrew the two domed nuts from both
the left and right panels. Finally, unscrew two nuts
securing the panels just below the rear of the fuel
tank, then remove both panels. Remove the
distance piece from each of the engine plates and
place them in safe keeping.
Unscrew the securing nuts and withdraw the car-
buretter. Note that there is a spring washer under
each of the four nuts, on the twin carburetter
B4
models. On models fitted with one carburetter
slacken the clamping screw and remove the air
cleaner. Remove any necessary cable clips and place
the carburetter(s) well clear of the engine in a safe
position.
Unscrew the two domed nuts from the rocker
spindles and disconnect the rocker oil feed pipe.
Care should be taken not to bend the pipe ex-
cessively as this may ultimately result in the pipe
fracturing.
Fig_ B2. Tachometer drive cable and adaptor
To drain the oil tank remove the drain plug from
the base of the oil tank and allow the oil to drain
for approximately 15 minutes. The oil feed pipe and
return pipe should then be disconnected from the
base of the oil tank. On earlier models the drain
plug is absent, and in this case the oil tank should be
drained by unscrewing the union nut and discon-
necting the oil feed pipe. Where the oil pipe rubber
connectors are secured by means of circular clips,
the clips should be slackened prior to disconnecting
the rubber connectors.
ClassicBike.biz
ENGINE B
At this stage it is advisable to drain the oil from the
gearbox and primary chaincase by removing the
respective drain plugs. The sump should also be
drained; this can be done by unscrewing the
hexagon-headed filter drain plug situated under-
neath the engine adjacent to the bottom engine
mounting lug. (See Fig. A3, reference No.4).
Slacken off the clutch adjustment at the handlebar,
withdraw the rubber seal from the clutch abutment
at the gearbox and unscrew the abutment. Detach
the slotted plug on the outer cover. Slip the bottom
nipple of the clutch cable free of the operating arm.
On earlier models there is no inspection cap on the
outer cover. In such cases the cable lower nipple
fits into a slotted barrel nipple revealed as the
abutment is unscrewed.
Drain plug
Fl 83. Clutch cable adjustment and gearbox drain
plug
Slacken the left and right finned clips and silencer
clip bolts and remove the forward exhaust pipe nuts
and bolts. Drive the exhaust pipes free with a hide
hammer.
On earlier models where siamesed pipes are fitted,
the pipe junction clip should also be slackened.
On earlier models, where the footrests are fitted
direct onto the frame, underneath the engine, it will
be necessary to remove them. To do this first
remove the brake pedal and swing it clear. Unscrew
the nuts from the two bolts securing the footrests,
then give each footrest a sharp tap in a downward
direction.
Remove the connecting link from the rear chain and
withdraw the chain from mesh with the gearbox
sprocket, then disconnect the 2 generator leads
underneath the engine (3 snap connectors on earlier
models or 5 in the case of a machine with A.C.
ignition).
To avoid damage to the chainguard. when the engine
is being removed, it should be moved rearwards
several inches. This can be achieved by slackening
the rear chainguard bolt and removing the front
securing bolt. The guard should then be lifted up-
wards and rearwards until it is well clear.
Remove four bolts and a nut securing each of the
left and right rear engine mounting plates and with-
draw the plates. Remove a nut and wa.sher from
one end of each of the front and bottom engine
mounting studs, the engine should now be loose in
the frame.
Finally to gain clearance for removal of the engine
unit from the LEFT, remove the following:-
(1) The two right-side rocker box-to-torque stay
bolts.
(2) The two right-side screws securing the front
and rear rocker cap retainer springs.
(3) The left side lower bolts securing the rear
frame to the front frame.
If the front and lower engine mounting studs are
now withdrawn the engine will be free to be re-
moved. It is recommended that removing the engine
should be aided by the use of a hoist or the help of
a second operator. due to the engine weight. which
is approximately 135 Ibs.
Should difficulty be experienced in removing the
engine, an easier removal can be facilitated by first
detaching the rocker boxes. For details of this see
Section B2.
Replacement is a reversal of the above instructions,
but do not forget to refit the bolts in (1), (2) and (3)
above when the engine is loosely positioned. When
replacing the ignition coils, remember that the
connector terminal end of each coil faces towards
the rear of the machine. To ensure that the wiring
harness is re-connected correctly refer to the
appropriate wiring diagram in Section H19.
Do not forget to fit the distance pieces on the coil
mounting bolts, torque stay mounting bolts, and,
in particular, the lower engine mounting stud:
also, attention is called to the distance pieces fitted
to the bottom panel mounting studs on the left and
right of the machine in the case of models fitted with
the rear enclosure panels.
For the correct grade and quantity of lubricant for
the engine, gearbox and chaincase. see Section A2.
B5
ClassicBike.biz
B ENGINE
SECTION B2
REMOVING AND REPLACING THE ROCKER BOXES
Disconnect the leads from the battery terminals
and remove the fuel tank as detailed in Section E1.
Disconnect the high tension cables and wiring
harness from the left and right ignition coils.
Remove the top and bottom coil mounting bolts and
distance pieces. The ignition coils will then be free
to be removed. Care should be taken not to damage
the light alloy casi ngs ofthe ignition coils as indenta-
tions may ultimately result in ignition failure.
Unscrew the four nuts securing the torque stays to
the rocker boxes and remove the front and rear
torque stay mounting bolts and distance pieces.
The torque stays should then be removed.
Unscrew the two domed nuts from the rocker
spindles and disconnect the rocker oil feed pipe.
Care should be taken not to bend the pipe exces
sively as this may ultimately result in a fracture.
Remove the rocker inspection caps.
Fig. 84. Rocker box securing nuts
Unscrew three nuts from the studs fitted to the
underside of the exhaust rocker box. Remove the
outer exhaust rocker box securing bolts and un-
screw the central cylinder head bolts. (Note that,
at this stage the rocker box may rise slightly, due to
a valve spring being compressed). The exhaust
rocker box is now free to be removed. The pro-
cedure is the same for the inlet rocker box, but the
two outer securing nuts indicated in Fig. B4 may
not have sufficient clearance to be removed; if
this is the case, they should be initially slackened
and finally unscrewed at the last stage, prior to
removal, when the rocker box can be lifted slightly.
86
Care should be taken to collect the six plain washers
which are fitted (one beneath each ofthe underside
securing nuts), as they sometimes adhere to the
cylinder head flanges and may be subsequently lost.
After completion of the rocker box removal opera-
tion, the push rods should be withdrawn and stored
in the order of their removal so that they can be
replaced in t.heir original positions.
The junction surfaces of the rocker boxes and
cylinder head should be cleaned for reassembly, by
means of a soft metal scraper.
Replacement is a reversal of the above instructions,
but remember to fit new gaskets between the
rocker boxes and cylinder head.
When replacing the push rods place a small amount
of grease into the bottom cup of each of the push
rods, then locate the push rods, one at a time, by
means of feeling the engagement of the tappet ball
end and the push rod cup, and then testing the
resistance to lifting caused by suction between the
dome of the tappet and push rod cup. When the
push rods are correctly located, remove the spark-
ing plugs and turn the engine over until the INLET
push rods are level and at the bottom of their
stroke. The inlet rocker box should then be
assembled. Repeat this procedure for the exhaust
rocker box.
Remember that the four central cylinder head
through bolts should be fitted first and that the
underside nuts are tightened last. Before finally
clamping the rocker boxes in position, check that
the valves are being operated by turning the engine
over slowly.
Do not forget the distance pieces which fit over the
engine torque stay mounting bolts and coil mount-
ing bolts.
NOTE: It can be seen that the four double
ended bolts also serve to retain the cylinder
head and should be tightened first. The
correct torque figures are given in GENERAL
DATA, and sequence, in Fig B12,
Before fitting the rocker oil feed pipe the four
copper washers which fit over the rocker spindle
should be annealed by quenching in water from
cherry red heat. Finally, remove any scale that may
have formed. Annealing softens the copper thus
giving it better sealing qualities.
ClassicBike.biz
ENGINE B
SECTION B3
INSPECTING THE PUSHRODS
When the push rods have been removed, examine
them for worn, chipped or loose end-cups; also
check that the push rod is true by roiling It slowly
on a truly flat surface (such as a piece of plate glass).
Bent push rods are found to be the cause of
excessive mechanical noise and loss of power and
should be straightened if possible, or, preferably.
renewed.
SECTION B4
STRIPPING AND REASSEMBLING THE ROCKER BOXES
Removal of the rocker spindles from the rocker i l l l l ~ ~ ~ ~ ~ ~ ~ ~ ; ~ ~ ; ~ ~ ~ ~ r
boxes is best achieved by driving out. using a soft a@if '[. d . ( d .' .F?1!Q
metal drift. When the spindles are removed the t
rocker arms and washers can be withdrawn. All
parts should be thoroughly cleaned in paraffin 10
(kerosene) and the oil d rillings in the spindles and
rocker arms should be cleaned with a jet of com-
pressed air.
Remove the oil seals from the rocker spindles and
renew them.
If it is required to renew the rocker ball pins, the
old ones should be removed by means of a suitable
drift. New ones should then be pressed In with the
drilled flat towards the rocker spindle.
To ensure an Oil-tight seal between the rocker box
and cylinder head, in cases where an oil leak cannot
be cured by fitting new gaskets, the joint surface
of the rocker box should be linished to remove any
irregularities.
An effective linish can be achieved by first extracting
the rocker box studs (two nuts locked together on
the stud should facilitate an easy removal) then
lightly rubbing the junction surface on a sheet of
emery cloth mounted on a truly flat surface (such
as a piece of plate glass).
Assembly of the rocker spindles into the rocker
boxes is assisted by the use of the oil seal compressor
D2221.
Fig. B5. Rocker box assembly
The following method of assemoly incorporates the
use of a home made alignment bar, which can be
made from a f. in. dia. bolt x 6 in. long by grinding
a taper at one end.
Before reassembly. note that, unlike earlier models,
the four plain washers on each rocker spindle are
all of the same size.
B7
ClassicBike.biz
8 ENGINE
Fl&,. B6. Refitting the rocker spindle
Smear two plain washers with grease and place them
one either side of the centre bearing boss. Place
the left rocker arm in position, bringing it into
line with the alignment tool and slide a plain washer
and a spring washer (in the order shown in Fig. B5)
into position. Carefully repeat this procedure for
the other rocker arm and spring washer and slide
the last plain washer into position. Finally bring
each rocker arm in turn into line with the alignment
bar.
lubricate the spindle with oil and slide it (complete
with oil seal) through the compressor (D2221) and as
far as possible into the rocker box, finally tapping
it home with a hammer and soft metal drift (see
Fig. B6).
SECTION 85
ADJUSTING THE VALVE ROCKER CLEARANCES
The valve rocker clearance should be checked and
adjusted if necessary every 3,000 miles (4,800 Km.).
The correct clearance, for the type of camshaft
employed, ensures that a high valve operating effici-
ency is maintained and that the valves attain their
maximum useful lives. The correct clearances are
given in "General Data".
NOTE: Adjustments should only be made
when the engine is CO LD.
Access to the rocker arm adjuster screws and lock-
nuts is gained by removing the slotted inspection
caps from the rocker boxes. Adjustment is aided
by the toolkit spanners D370 (f. in. Whit, spanner)
and D362 (tappet key).
First, remove the left and right sparking plugs to
relieve compression. then slacken the four lock nuts
securing the square-headed adjuster screws. Slowly
turn the engine over until the left exhaust valve is
fully open; the right tappet is then resting on the
base-circle diameter of the cam-form opposite to
B8
the cam-lobe; the clearance for the right exhaust
valve can then be set (see Fig. B7). Carefully turn
the adjuster screw in the required direction until
the correct feeler gauge just slides between the
valve stem and the screw. Re-check the gap after
the lockn ut has been tightened.
Fig. 87. Adjusting the valve rocker clearance
ClassicBike.biz
ENGINE B
Repeat this procedure for the left exhaust valve and
both of the inlet valves, ensuring that the clearances
are in accordance with those given in "General
Data",
An alternative way of setting the valve rocker
clearance which is approximate but sufficient when
carefully carried out, is that of using the pitch of the
thread on the adjuster screw as a vernier scale.
The thread is -fr in. x 26 C.E.I. hence the pitch"
038 in. Therefore, * turn of the adjuster screw
represents 010 in. approx.
If the adjuster screw is initially turned until it Is
frnger tight on the valve stem, so that the rocker
arm can only be moved Sideways; then, by slacken-
ing the screw * turn. a clearance of apprOXimately
010 in. will result. Similarly, slackening the
screw i turn will give a clearance of 005 In.
SECTION B6
REMOVING AND REPLACING THE AIR CLEANER
earlier type
later type
Fig. B8. Air cleaners
The T120 has separate air filters ofa similar type to
that used on the TR6. These have clip fittings or in
the case of concentric carburetters are threaded
directly on to the carburetter bodies. In the case
of a TR6 the switch panel should be removed
(Section E3). Then, when the central circular clip
is slackened it should be possible to slide the air
cleaner off the carburetter adaptor. and withdraw it.
On earlier models with one carburetter where rear
enclosure panels are fitted it will first be necessary
to remove the right panel. This is done by unscrew-
ing the two front panel junction screws, two domed
nuts and a nut just below the rear of the fuel tank.
If difficulty is encountered it is possible to remove
the air cleaner by dismantling it. To do this remove
the screwed clip which secures the outer perforated
case, then remove the back plate, filter and finally,
slide the front plate from over the carburetter
adaptor.
Dry felt and coarse felt elements should be carefully
rinsed in paraffin (kerosene) and allowed to drain
thoroughly.
Under no circumstances should the filter be soaked
with oil. Paper elements should be blown clean
with a jet of compressed air.
Replacement is the reversal of the above instruc-
tions but do not forget to tighten the perforated
case clip and the circular clip securing the air
cleaner to the carburetter.
The earlier T120 model was fitted with a combined
air cleaner for some markets, and the Spare Parts
Catalogue lists the parts required. This type of
air cleaner had a paper element which should be
removed and cleaned with a jet of compressed air,
or renewed, as necessary. This paper element
should not be washed or immersed in any
liquid.
B9
ClassicBike.biz
8
ENGINE
SECTION 87
CARBURETTER-DESCRIPTION
ADJUSTER
CLICK SPRING
CAP
TOP
THROTTLE
SPRING
THROTTLE
SLIDE
JET NEE'DLE-------li
MIXING ----------+
CHAMBER
'0' RING SEAL
AI R SC REW ----.o!jllll .....
LOCATING _____
PEG
NEEDLE

PILOT JET
COVER NUT
MAIN JET __________ F
HOLDER
MAIN
MAIN JET
COVER NUT

------------------AIR VALVE GUIDE

BOLT

.,/---------FILTER GAUZE
'r--- AIR FILTER
CONNECTION
+
ALTERNATIVE
t
'f7-__________ AIR INTAKE
TUBE
NEEDLE SEATING

COVER
SCREW
L-----------------FLOAT
L----------------FLOAT NEEDLE
33
Fi,. B9. Exploded view of carburetter
810
ClassicBike.biz
ENGINE
CONCENTRIC CARBURETTER TYPE 900
DESCRIPTION
SPRING
MIXTURE
CHAMBER
LAIR VALVE
~ GUIDE SLEEVE ADJUSTER-- iJ ~
f', - AIR VALVE ~ ~ .
I ~
-TOP
'X:::>-THROTTLE SPRING
THROTTLE
SLIDE
TICKLER
--"-''''i'cc+ TICKLER
SPRING
~ - - NEEDLE CLIP
AIR SCREW
THROTTLE STOP
---- NEEDLE JET
JET HOLDER
j,\------MAIN JET
FLOAT
FLOAT NEEDLE--- - 7 - - ' ~ 1
,..""'--- FLOAT SPINDLE
BOWL -
FILTER --
-. BANJO
- BANJO
BOLT
B261
Fig. B9B Exploded view of carburetter
B
B11
ClassicBike.biz
8 ENGINE
The T120 and TR6 are each fitted with Amal
carburetters which are fully adjustable.
Briefly, they operate in the following way:
When the engine is idling. mixture is supplied from
the sealed pilot jet system. then as the throttle slide
is raised, via the pilot bypass. With the throttle
just opening the mixture is controlled by the
tapered needle working in the needle jet and finally
by the size of the main jet. The pilot system is
supplied by a pilot jet, fitted into the
carburetter body_ The main jet does not feed
direct into the mixing chamber but discharges
through the needle jet into the primary air chamber
and the fuel Roes from there as a rich petrol-air
mixture through the primary air choke into the
main air choke.
This primary air choke has a compensating action in
conjunction with bleed holes in the needle jet,
which serves the double purpose of air-compensat-
ing the mixture from the needle jet, and allowing
the fuel to provide a well. outside and around the
needle jet, which is available for snap acceleration.
The idling mixture is controlled by the pilot air
screw which governs the amount of air that is
allowed to mix with the fuel at tick-over speeds.
The throttle stop screw is used to adjust the slide
so that the throttle is kept open sufficiently to keep
the engine running at a slow tick-over, when the
twist-grip is closed.
SECTION 88
REMOVING AND REPLACING THE CARBURETTER
'INSULATING BLOCK
RUBBER RING
Fig. B10A Manifold assembly
Single carburetter models
107
Due to the carburetter top securing screws being
inaccessible with the petrol tank fitted. it will be
necessary to dismount the carburetter before
removing the top for any reason.
First remove the air cleaner(s) as in Section B6.
Ensure both taps are in the "off" position and dis-
connect the fuel pipes at the taps beneath the rear
of the tank. Unscrew the two carburetter flange
securing nuts (self-locking) then carefully withdraw
the carburetter from over its mountipg studs.
In the case of twin carburetter models. lift off the
cups and "0" rings shown in Fig. B10BThe car-
buretters can then be lifted off the mounting studs.
To achieve this the carburetter should be tilted
upwards so that it clears the frame. As the car-
buretter is lowered. the top can be removed by
taking out the two Phillips headed screws. Unless
the top. slides etc. are to be removed, from the
cables they can be wrapped carefully in a piece
of cloth until the carburetter is to be refitted.
B12
Machines prior to DU.66246 are fitted with a mono-
bloc type of carburetter. The procedure for its
removal is similar to above. except for the mixing
chamber top. This item is secured by a screwed
ring. and spring clip.
On single carburetter models the insulating block.
paper washer and rubber "0" ring seal should
be examined for damage which might impair their
sealing qualities. If there is the slightest doubt
about their serviceability. they should be renewed.
When replacing the carburetter. great care should
be taken to ensure that the slide does not become
damaged as it is lowered into the mixture chamber.
The peg at the top right of the slide locates in a
corresponding groove in the carburetter body.
Care must be taken when replacing the slide as the
needle must be located in the needle jet, before
the slide can be positioned in the mixing chamber.
When the slide has been assembled satisfactorily.
refit the mixing chamber top. two screws and lock
washers.
Fig. B108 order of assembly
Twin carburetter models
In the case of twin carburetter models, no insulating
block and paper washer are used. On these models.
fit the "0" ring seal and carburetter, followed by
the small insulating "0" rings and cups (see Fig.
B10B)over the locating studs. Care should be taken
not to overtighten the two carburetter securing
nuts.
ClassicBike.biz
ENGINE B
SECTION B9
STRIPPING AND REASSEMBLING THE CONCENTRIC CARBURETTER
When the carburetter is removed. disconnect the
slide assembly from the throttle cable. To do this
pull back the return spr'lng and remove the needle
and needle clip. With the spring still retracted.
push the cable through the slide and when the
nipple is clear, across the figure of eight slot. The
slide and return spring can now be removed.
To remove the air valve. push the valve and spring
along with air cable until the cable nipple pro-
trudes sufficiently out of its counterbore to be
pushed out of the slot. The cable and spring can
now be pulled clear of the valve.
Unscrew the petrol pipe banjo connection and
remove the banjo and nylon filter.
Unscrew two Phillips screws and remove the float
bowl. The nylon float, spindle and triangular needle
can now be withdrawn.
Unscrew the jet holder which will allow the main
jet to be removed.
Unscrew the air adjusting screw and throttle stop
screw.
Thoroughly clean all parts in petrol (gasoline)
several times and dry with compressed air, or a
hand pump, to remove any particles of dirt. Any
external deposits are best removed with the use
of a light wire brush.
Reassemble in the reverse order. referring to Fig.
B9 for gUidance.
When refitting the float and needle valve. make
certain that the recess on the valve is properly
located in the "U" shaped slot in the float. Replace
the float bowl sealing washer. and if necessary the
tWO rubber "0" rings fitted to the adjusting screws
STRIPPING AND REASSEMBLING THE MONOBLOC CARBURETTER
When the carburett'er is removed, d'lsconnect the
slide assembly from the throttle cable. To do this.
first remove the needle retaining spring clip. then
compress the slide return spring, pushing the
nipple of the throttle cable down through the slot
until it is free.
Unscrew three slotted screws and withdraw the
float chamber cover and remove the float spindle
bush and float; then withdraw the triangular
sectioned float needle.
Unscrew the banjo bolt which secures the fuel pipe
banjO connector to the float needle seating block
and withdraw the banjo. filter and junction washers.
Unscrew the needle seating block. Unscrew the
t'lckler body then withdraw the tickler and spring.
Unscrew the air screw and throttle stop screw, then
the main jet cover nut from the bottom of the body.
Unscrew the main jet, main jet holder and needle
jet. To release the jet block reinsert the main jet
holder. until a few threads are engaged then tap it
with a hide hammer. This will release the jet block
upwards and through the carburetter body.
Unscrew the pilot jet cover, and unscrew the pilot
jet. All that remains to be removed then is the
hexagonal locating peg. the end of which can be
seen protruding within the mixing chamber.
Thoroughly clean all parts in petrol (gasolene).
Deposits on the carburetter body are best removed
by a light grade wire brush. It is advisable to wash
the parts several times each in a quantity of clEan
petrol, to avoid particles of dirt remaining. Allow
the parts to drain, preferably using a jet of com-
pressed air from such as a hand pump to ensure
that oil holes and drdlings are from from blockage.
B13A
ClassicBike.biz
B ENGINE
Inspect the component parts for Wi.!ar and check
that the jets are in accordance with the recom-
mended sizes given in GENERAL DATA.
Apart from one or two points that are mentioned
below. reassembly is a reversal of the above
instructions, referring to Fig. B9Bfor gUidance.
Do not refit any fibre washer that looks un-
serviceable. It is advisable to purchase replacement
washers before removing the carburetter.
When replacing the jet block, ensure that the fibre
washer is in position; align the location flat in the
jet block with the locating peg in the carburetter
housing and drive the block home.
Finally. note that the float spindle bush fits on the
outside end of the spindle. and that the float
pressure pad is uppermost so that the float needle
rests on it.
SECTION BIO
INSPECTING THE CARBURETTER COMPONENTS
(CONCENTRIC AND MONOBLOC)
The only parts liable to show wear after consider-
able mileage are the throttle valve slide, mixing
chamber and the air slide (if fitted).
(1) Inspect the throttle valve slide for excessive
scoring to the front area and check the extent
of wear on the rear slide face. If wear is
apparent the slide should be renewed. In this
case, be sure to replace the slide with the correct
degree of cut-away (see "General Data").
(2) Examine the air valve for excessive wear and
check that it is not actually worn through at
any part, Check the fit of the air valve in the
jet block, Ensure that the air valve spring is
serviceable by inspecting the coils for wear.
(3) Inspect the throttle return spring for efficiency
and check that it has not lost compressive
strength by measuring its length and comparing
it to the figure given in "General Data",
8138
(4) Check the needle jet for wear or possible
scoring and carefully examine the tapered
end of the needle for similar signs. Check
the correct needle is in use. The needle for
petrol is marked above the top groove "000".
The needle for alcohol is marked "Z".
(5) In the case of monobloc carburetters examine
the float needle for efficiency by inserting it
into the inverted float needle seating block.
pouring a small amount of petrol (gasoline)
into the aperture surrounding the needle and
checking it for leakage.
(6) Check the float bowl joint surface for flatness
and flatten if necessary on emery paper on a
perfectly flat surface.
(7) Ensure that the float does not leak by shaking
it to see if it contai ns any fuel. Do not attem pt
to repair a damaged float. A new one can be
purchased for a small cost.
ClassicBike.biz
ENGINE
B
(8) Check the petrol filter, which fits into the
petrol pipe banjo, for any possible damage to
the mesh. Ensure that the filter has not
parted from its supporting structure, thus
enabling the petrol (gasolene) to by-pass It
un-filtered.
(9) Concentric float carburetters have a pressed-in
pilot jet which is not removable. If the jet
becomes blocked the machine will be hard to
start and will not run at low speeds. This can
be cleared by blocking the low speed air
passage at the bell end of the carburetter
removing the pilot air screw and using a jet
of air at this point.
SECTION BII
CARBURETTER ADJUSTMENTS
Throttle Stop Screw. This screw, which is
situated on the right side of the carburetter (L.H.
in case of current T120 left hand carburetter)sloping
upwards and is fitted with a friction ring. should be
set to open the throttle sufficiently to keep the
engine running at a slow tick-over, when the twist-
grip is closed. Monobloc instruments have locking
springs rather than friction rings.
Pilot Air Screw. To set the idling mixture, this
screw, which is situated on the right side, is also
fitted with a friction ring or locking spring. and
should be screwed in to enrichen the tick-over
mixture or outwards to weaken it. As a gUide to
its approximate required position. screw it in
fully, then unscrew it approximately 2t turns.
The screw controls the suction on the pilot jet by
metering the amount of air which mixes with the
petrol.
Needle and Needle Jet. Carburation is gov-
erned by the cut-away and needle jet in varying
degrees from when the throttle is just open to
when it is approximately i full throttle. The needle
jet orifice is governed by the position of the needle.
The needle position should not be altered from its
specified setting without specialist advice.
Throttle Valve Cutaway. The amount of cut-
away to the bottom of the throttle valve slide Is
indicated by a number marked on the slide, e.g.
930(3t means throttle type 930 with number 3t
cutaway; a larger number such as -4 means that the
throttle valve slide has a slightly larger cutaway and
consequently gives a weaker mixture during the
period of throttle opening through which a cutaway
is effective, i.e. from just open to approximately
* throttle. Similarly, 3 indicates a slightly smaller
cutaway and a slightly stronger mixture.
Jet Sizes. The recommended jet sizes are given
in "General Data" and changing from these to any
other size it is left entirely to the discretion of the
rider. The main jet is operative from approximately
i to full throttle. this is when the needle jet orifice
ceases to have any reduction effect on the petrol
flow.
B13C
ClassicBike.biz
8 ENGINE
SECTION 812
TWIN CARBURETTER ARRANGEMENT
DESCRIPTION
Twin carburetters are fitted to T120 and T120R
machines. There is a balance pipe fitted between
the inlet manifolds to improve tickover.
THROTTLE CABLE
On U.K. and General Export models a "one into
two" throttle cable is used. The single throttle
cable from the twistgrip enters a junction box
where it is fitted into a slide. The twin shorter
carburetter cables are fitted to the other side of
the junction box slide. Both the slide and junction
box being made of plastic require no maintenance.
To remove the throttle cable the petrol tank must
be lifted to release the cable to frame clip.
A similar cable arrangement is used for air slide
operation.
SETTING TWIN CARBURETTERS
The twin carburetters fitted to the T120 and T120R
may require synchronisation and a simple method is
as follows: First adjust the cables from the junction
box so that they have the minimum of free play.
Now start the motor and take off one plug lead
and then adjust the pilot air screw and throttle
stop screw in the OPPOSITE carburetter until the
motor runs regularly. Replace the plug lead and
repeat the process similarly for the other car-
buretter. With both plug leads replaced the tick-
over will be too fast and the stop screws should be
lowered simultaneously until correct. It is most
important the throttle slides lift simultaneously or
the motor will run roughly. particularly when
accelerating.
SECTION 813
REMOVING AND REPLACING THE EXHAUST SYSTEM
T120, T120R, TR6. TR6R
To remove the exhaust system slacken the exhaust
pipe to silencer clamp bolts. Remove the self
locking screws and cruciform headed screw from
the front bracket.
Slacken the four clamp bolts at the front cross-over
pipe and slide in the outer sleeves. tapping them
with a rubber mallet if necessary. Slacken the
finned cooling ring clamp bolts and drive the ex-
haust pipes clear of the exhaust adaptors.
Remove the silencer to exhaust pipe clips complete
with bracing strap and remove the bolt, spring
washer and nuts from back silencer hanger bracket.
The silencers are now free to be removed.
B14
To refit the exhaust system, first fit the silencers
with the brackets inboard of the hangers. Loosely
assemble the bolts. spring washers and nuts
(the bolts from the inside). Loosely assemble
the silencer forward clamp and bracing strap
with the strap and nuts underneath. Offer the
finned cooling rings over the exhaust pipes but
do not tighten. Drive the exhaust pipes over the
cylinder head stubs and into the silencers. Loosely
assemble the front bottom exhaust stays to the
exhaust pipes, the cruciform headed screws from
the front and self locking nuts behind. Lift the
cross-over pipe complete with sleeves into position.
Slide the cross piece outer sleeves over the exhaust
pipe "branches". Finally tighten all nuts and bolts
securely.
ClassicBike.biz
ENGINE
B
TR6C MACHINES ONLY
To remove the exhaust system commence by re-
moving the leg guard. This can be achieved by
removing two scre:ws and washers which screw
into captive nuts. The leg guard retaining clips can
now be withdrawn complete with the screws,
and the leg guard removed.
It is advisable to remove the exhaust system in two
sections, the first being the right and left exhaust
pipes and brackets.
Slacken two bolts which secure the exhaust pipe
rear stay. one bolt screws into each pipe, and remove
one bolt and spring washers from the spacer at ihe
top front engine mounting bolt on the left side
rear engine plate. Slacken the finned cooling rings
at the cylinder head, and slacken two exhaust pipe
to "H" connector clips. Using a
rubber mallet, drive the exhaust pipes
forward off their stubs.
The second section to remove is the
silencer assembly. This is simply a
matter of removing one nut, spring
washers and bolt from the upper
mounting clips on the rear frame
tube, and one nut, spring washer and .
left side rear engine plate. Tighten the finned
cooling rings, ensuring that both the rings and
exhaust pipes are in contact with the cylinder head
to avoid any gas leakage. Secure the clips which
retain the exhaust pipes in the "HI! connector at
the silencers. Fully tighten all three exhaust pipe
rear bracket bolts, and both the upper and lower
silencer bracket bolts.
Finally refit the silencer leg guard. One screw,
washer and clip should be fitted at the front of the
leg guard, and screwed into the double curved
bracket which is fitted from behind the exhaust
pipes, and the rear screw, washer and clip should
be attached to the fixed silencer bracket.
in the rear footrest mounting bracket. _ (::j? 'I;l
bolt from the lower mounting point
The assembly is now free to be re-
moved. ______ ....... -
If it is found necessary to dismantle -tt
thesilencerassembly,referenceshould "
be made to Fig. B11 for gUidance.
To replace the exhaust system, re
position the silencer assembly and
replace the upper and lower retaining
bolts, spring washers and nuts. noting
that both bolts are fitted from the
outside. It is not advisable to tighten
these bolts at this stage. Ensure that
the cooling rings are fitted to the
cylinder head stubs, and replace both
exhaust pipes, driving them into the
silencers with a rubber mallet.
Replace, do not tighten the bolt
and spring washers which secures
the exhaust pipe bracket to the top
front engine mounting bolt on the
Fig. B11. Showing order of assembly of USA TR6C exhaust system
B15
ClassicBike.biz
B ENGINE
SECTION BI4
REMOVING AND REFITTING THE CYLINDER HEAD ASSEMBLY
Proceed as detailed in Section B2 for removal of
the rocker boxes and push rods.
Remove the exhaust system as in Section B13.
Unscrew the left and right carburetter flange nuts
and remove them complete with spring washers.
Both carburetters should then be withdrawn from
over the studs and placed well clear of the cylinder
head. On models where one carburetter is fitted
the manifold securing nuts should be unscrewed
and the manifold withdrawn when the cylinder
head is removed. Note that there is a plain washer
under each of the four manifold securing nuts.
Unscrew the remaining five cylinder head bolts, a
turn at a time, until the load has been released,
and then remove the cylinder head, if necessary,
sliding it forward to release the inlet manifold.
Remove the push rod cover tubes and note that it
is essential to renew the rubber seals. Check for
sharp edges on the corners of the top portion of
the tappet gUide blocks which could cut the new
'0' rings when reassembling. Use a file or emery
cloth to smooth any such sharp edges.
Fig. B12. Cylinder head bolt tightening sequence
B16
The copper cylinder head gasket should be either
renewed or reconditioned by annealing it to restore
the sealing qualities of the copper. Annealing is
achieved by heating the gasket to cherry-red heat
and quenching it in water; finally. remove any scale
that may have formed by means of a piece of fine
grade emery cloth.
REFITTING THE CYLINDER HEAD
Ensure that the junction surfaces of the cylinder
block, gasket and cylinder head are clean. Grease
the gasket and place it in position (check that all
9 bolt holes are lined up), coat the tappet gUide
blocks with heavy grease and locate the push rod
cover tubes (complete with top and bottom 011
seals). Relieve any roughness at the push rod tube
counterbores in the head.
Lower the cylinder head 'Into position over the
push rod cover tubes and fit the four outer cylinder
head bolts finger tight, also, fit the central bolt
fi nger tight.
Carefully rotate the crankshaft until both of the
inlet push rods are at the bottom of their stroke,
then lower the inlet rocker box into position,
ensuring that the push rods are engaged correctly,
then fit the two central cylinder head through bolts
finger tight. Screw in the two outer inlet rocker
box bolts and fit the three underside retaining
nuts, with plain washers. Repeat this procedure
for the exhaust rocker box.
Tighten the nine cylinder head bolts in the
order given in Fig. B12 and to the torque set-
tings given in "General Data". Finally tighten
the remaining inlet and exhaust rocker box
retaining nuts and bolts.
Reassembly then continues in the reverse order
to the removal instructions. To obtain the
correct valve rocker clearance settings. reference
should be made to Section B5.
ClassicBike.biz
ENGINE B
SECTION BIS
REMOVING AND REFITTING THE VALVES
Removal of the valves is facilitated by means of a
"G" clamp type valve spring compressor. When
the spring is compressed sufficiently. the split
cotters can be removed with a narrow screwdriver.
and the valve spring withdrawn when the com-
pressor is released. As each valve is removed it
should be marked so that it can be replaced in its
original position.
NOTE: The inlet valves are marked "IN"
and the exhaust valves "EX".
Fitting a new or reground valve necessitates seating
by the grinding in process described in Section B1B.
but it does not necessitate recutting the cylinder
head valve seat unless new valve gUides have been
fitted.
The valve springs should be inspected for fatigue
and cracks. and checked for wear by comparing
them with a new spring or the dimension given in
"General Data",
(kerosene) and allowed to drain before reassem-
bling.
Fig. 813. Valve components
Assemble the inner and outer springs and top and
bottom cups over the valve gUide. then slide the
valve into position lubricating the stem with a small
amount of graphited oil.
Compress the springs and slide the two halves of
the split cotter into the exposed groove in the
valve stem.
SECTION BI6
RENEWING THE VALVE GUIDE5
The valve gUides can be pressed or driven out using
service tool 61-6013. with the cylinder head inverted
on the bench. A suitable drift can be made by
obtaining a 5 inch length of t in. diameter mild
steel bar (ENB) and machining one end to ,.. in.
diameter for a length of 1 inch.
The same method may be employed to fit the new
gUide. although the use of a press is recommended.
In either case lightly grease the valve guide to assist
assembly. Ensure that the gUide is pressed in until
the shoulder is flush with the cylinder head.
Bronze valve gUides are fitted, the shorter ones
being used in the inlet position.
Where new valve gUides have been fitted it is
necessary to re-cut the valve seats in the cylinder
head and grind in the valves (see Section B1B).
B17
ClassicBike.biz
8
ENGINE
SECTION 817
DECARBONISING
It is not normally advisable to remove the carbon
deposits from the combustion chamber and exhaust
ports until symptoms indicate that decarbonising is
necessary.
Such symptoms as falling off in power, loss of com-
pression, noisy operation and difficult starting are
all indications that decarbonising may be necessary.
When the cylinder head is removed unscrew the
sparking plugs and dean them in paraffin (kerosene),
or preferably have them grit-blasted and checked.
Before fitting the plugs, check that the gap setting
is correct (see "General Data").
If special decarbonising equipment is not available
then a blunt aluminium scraper or a piece of lead
solder flattened at one end, should be used to
remove the carbon deposits. Do not use a screw-
driver or a steel implement of any kind on an
aluminium surface.
When removing the depOSits from the piston
crown, a ring of carbon should be left round the
periphery of the pistons to maintain the seal. Also
the carbon ring round the top of the cylinder bore
should not be disturbed. To facilitate this an old
piston ring should be placed on top of the piston,
level with the top surface of the cylinder block.
Remove the valves as shown in Section B15 then
remove the carbon deposits from the valve stems,
combustion chamber and ports of the cylinder head.
Remove all traces of carbon dust by means of a jet
of compressed air or the vigorous use of a tyre
pump, then thoroughly dean the cylinder head and
valves in paraffin (kerosene). Finally, check the
valves for pitting. If necessary. the valves can be
ground-in as shown in Section B18.
SECTION 818
RE-SEATING THE VALVES
Where the valve gUides have been renewed or the
condition of a valve seat 1s doubtful, it is advisable to
re-cut the cylinder head valve seat then grind in
the valve, using a fine grade grinding-in paste.
It Is important that the cylinder head valve seat and
the valve gUide bore should be concentric. For the
purpose of re-cutting the valve seats the following
service tools are available.
B18
01832 Valve seat cutter exhaust (45)
01833 Valve seat cutter inlet (45)
01834 Blending cutter (spherical form)
01863 Arbor with pilot.
The valve seat cutting operation should be carried
out with the greatest care, and only a minimum
amount of metal should be removed.
ClassicBike.biz
ENGINE B
After the seats have been re-cut, they should be
blended to give an even seating of * in. (2.4mm.).
Examine the face of the valve to see if it is pitted,
scored or damaged. If necessary, the face can be
reground. but excessive re-grinding is not advisable
for this adversely affects the heat transference
properties of the valve and will ultimately result
in critical pocketing.
The stem of the valve should be inspected for wear
or scuffing and if either is pronounced. the valve
should be renewed.
(
fiO
Fig. B15. Valve seating tools
'0
16
Fig. B14. Cutting a valve seat
To grind in the valve use a fine grade carborundum
grinding paste. Place a small amount evenly on the
valve seat and place the valve in its gUide with a
holding tool attached.
Use a semi-rotary motion. occaSionally lifting the
valve and turning it through 180. Continue this
process until a uniform seal results. Wash the parts
in paraffin (kerosene) to remove the grinding paste.
Apply a smear of "Engineer's" marking blue to the
seat of the valve. Rotate the valve th rough one
revolution and inspect both seats. Successful valve
grinding will give an unbroken ring of blue on the
valve seat.
Alternatively, assemble the springs and split cotter.
and pour a small amount of paraffin (kerosene) into
the port. It should not penetrate the seating for at
least 10 seconds if a good seal has been achieved.
Prior to reassembling the cylinder head, ensure that
all traces of "Blue" or grinding paste are removed
by thoroughly washing in paraffin (kerosene).
B19
ClassicBike.biz
B ENGINE
SECTION BI9
REMOVING AND REPLACING THE CYLINDER BLOCK AND TAPPETS
Wedge a dis-used shock absorber rubber, or a suit-
able retainer between the inlet and exhaust tappets
to prevent the tappets from falling through the
tappet block into the crankcase when the cylinder
block is removed. Turn the engine until the pistons
are at T.D.C. then unscrew eight nuts from the
base of the cylinder block and remove eight washers,
carefully raise the block clear of the pistor.s. Raise
the block sufficiently to insert non-fluffy rag into
the crankcase mouth. It is also advisable at this
stage to fit four rubber protectors (e.g. gear chapge
lever rubbers) over four cylinder base studs (see
Fig. B16) to avoid any damage to the alloy connecting
rods. Remove the cylinder base gasket and ensure
that the two locating dowels are in their correct
position in the crankcase.
Remove the tappets from the cylinder block storing
them in the order of their removal, and thoroughly
clean all parts in paraffin (kerosene). It is important
that the tappets are replaced in their original posi-
tions; failure to observe this may result in subse-
quent excessive tappet and cam wear.
If it has been decided to fit new piston rings then
the bores must be lightly honed as described in
Section B24.
Reassembly is a reversal of the above instructions,
but care should be taken to ensure that the cylinder
block is correctly located over the two dowels in
the left half-crankcase.
The tappets should be well lubricated prior to
wedging them in their original positions in the
tappet gUide blocks. To facilitate an easy assembly
of the cylinder block over the pistons, two collars,
Fig. 816 Refitting the cylinder block
part number Z22, are required. The collars should
be placed over the pistons to compress the piston
rings, and withdrawn over the connecting rods
when the pistons are sufficiently engaged in the
block. Refit the eight cylinder base nuts. If desired,
the latest 12 point base nuts and unified studs can
be fitted as a set to existing crankcases.
NOTE: The smaller cylinder block retaining
nuts should be fitted to the four central studs.
PRESSURE LUBRICATED EXHAUST TAPPETS
Lubricant is supplied under pressure direct to the
exhaust tappet and camshaft working faces as
described in section A3.
When replacing the cylinder block ensure that the
cylinder base gasket is not fitted in such a way that
the oil feed hole incorporated in the crankcase and
cylinder block is obscured, so preventing lubricant
from reaching the tappets.
If for any reason the tappet gUide block is removed.
it should be refitted as described in Section B19,
but the oil feed holes should be checked to ensure
that they are not blocked by foreign matter.
820
The correct method of assembly of the tappets
is shown in Fig. B17. The machined cut away faces
(C) should be facing the outside 01 the tappet guide
block. i.e. the tappets must not be fitted with the
cutaways faCing one another, otherwise the oil
holes (B) drilled in the annular groove olthe tappet
block (A) will not be able to supply lubricant to the
tappets.
N.B. The inlet and exhaust tappets and tappet guide
blocks must not be interchanged.
From engine number DU.24875, oil has been fed
through drillways in the crankcase, timing cover.
ClassicBike.biz
ENGINE
B

II-'--C
C---\
Fig. B17 Showing the correct method of assembly
of the exhaust tappets
cylinder barrel and tappet block to the rubbing
faces of the cam followers.
To prevent loss of oil pressure, several conditions
and variations on the original theme have been
employed.
Initially a metering plug was inserted into the
crankcase at the front timing cover dowel and
used in conjunction with cam followers with a flat
of 3
9
2 in. in length on the stem. Part No. E6490.
An alteration to this condition was made at engine
number DU.44394, in as much that a floating pin
was inserted into the metering screw, to combat
blockage caused by particles in the lubrication
system. Both metering jet and dowel can be
obtained under Part Nos. E6800 and E6803 respec-
tively, but these items must be used with (am
followers, part No. E6490.
From engine number DU.63043 however, this
assembly was removed, replaced with a plain
dowel, part number T989 and cam followers used
with a flat on the stem reduced in length to }2 in.,
part No. E8801.
If the newer pattern cam follower is to be used in
an engine previous to DU.63043, the metering plug
must be removed from the crankcase. To facilitate
this. simply screw in a timing coyer screw and
withdraw the assembly.
Do not remove the metering assembly if the old
type cam followers, part number E6490, are co be
used.
Do net attempt to use in the engine one of the
old pattern cam followers in conjunction with one
of the new type.
Timing cover Camra/lower Camra/lower Toppet
Engine No. Type Dowel Exhaust Inlet block
To Engine No. Blind dowel
i
DU.24875 Non lubricated None E3059 E3059 E1477
From DU.24875 Dowel E6329 6T /TR6 E3059 6T (TR6 i
To DU.44394 Lubricated E6348 E6490 T120 E3059R T120
I
E5861
From DU.44394 Dowel and Pi n E6490
I
To DU.63043 Lubricated E6803j6800
From DU.63043 Dowel
To DU.66246 Lubricated T989
If conversion to the latest exhaust cam followers is
desired on machines from engine number DU.24875
up to DU.63043, then the following procedure
must be carried out.
Remove the E6348 metering jet in the manner
prescribed above and replace with hollow dowel,
T120jTR6 E3059R
I
E5861
E8801 , E3059R E5861
part number T989. Replace exhaust cam followers
with the equivalent shown in the scale below.
Exhaust cam followers
E63296TjTR6 use E88956T(TR6
E6490 T120 use T120
ClassicBike.biz
ENGINE
B
SECTION B20
INSPECTING THE TAPPETS AND GUIDE BLOCKS
The base of the tappet is fitted with a "Stellite"
tip. This material has good wear resisting qualities
but the centre of the tip may show signs of slight
indentation. If the width of the indentation exceeds
tr in. then the tappet should be renewed.
It is not necessary to remove the tappet gUide
blocks for inspection purposes; the extent of wear
can be estimated by rocking the tappet whilst it is
in position in the gUide block. It should be a sliding
fit with little or no sideways movement, (see
"General Data" for working clearances).
Excessive play between the tappets and gUide
block may cause undesirable mechanical noise.
SECTION B21
RENEWING THE TAPPET GUIDE BLOCKS
Place the cylinder block in an inverted position on
the bench. Remove the locking screw and drift out
the gUide block using service tool 61-6008, as shown
in Fig. B1B.
"0" ring oil seals are fitted between the tappet
blocks and cylinder block. The seals must be re-
placed whenever oil leakage is noted at this point
or whenever the tappet blocks are removed and
refitted. Under no circumstances must the tappet
guide blocks be interchanged. The exhaust tappets
are pressure lubricated through the exhaust tappet
gUide block and the oilways must therefore be
cleaned out carefully before assembly.
To fit the new guide block, first grease the outer
surface to assist assembly, then align the location
hole in the guide block and cylinder block base, and
drive in the gUide block using 61-6008, until the
shoulder is flush with the flange.
B22
3"
Fig. B18. Refitting a tappet guide block
ClassicBike.biz
B ENGINE
SECTION B22
REMOVING AND REFITTING THE PISTONS
It is most important that the alloy connecting rods
are not damaged by contact with the sharp crank-
case edge. For this reason four gear lever rubbers
should be placed over the four central cylinder
base studs.
Removal of the pistons is facilitated by the use of a
proprietary removal tool (see Fig. B19). Remove
the inner and outer circlips and press out the
gudgeon pin with the removal tool. The pistons are
pistons are removed they should be SUitably
scribed inside so that they can be refitted in their
original positions. When refitting the pistons, first
place the Inner circlip In position to act as a stop.
then press the gudgeon pin into position using a
service tool.
It is advisable to renew the four circlips; this can
be done for negligible cost.
(;
Protective
. rubbers over BI36
.studs
Fig. 819. Removing a piston
then free to be removed. Alternatively. the pistons
may be removed by drivipg out the gudgeon pin
with a suitable drift. Howeve'-. this is not a recom-
mended practice. and may result in.a damaged
piston or distorted connecting rod. The need for
care cannot be overstressed when using thIs
method to remove the gudgeon pin. When the
If there is no alternative to driving the gudgeon pin
into position with a drift. the piston should be
heated to 100C (boiling-water temperature). to
assist assembly.
Finally. check that all the gudgeon pin retainer
clrclips are in position, and are correctly fitted.
This is extremely important.
B23
ClassicBike.biz
B
ENGINE
SECTION B23
REMOVING AND REPLACING THE PISTON RINGS
There should be little difficulty in removing piston
rings, if the following procedure is adopted, lift
one end of the top piston ring out of the groove and
insert a thin steel strip between the ring and piston.
Move the strip round the piston, at the same time
lifting the raised part of the ring upwards with slight
pressure. The piston rings should always be lifted
off and replaced over the top of the piston.
If the piston ri ngs are to be refitted the carbon
deposits on the inside surface of the rings must be
removed and the carbon deposits in the piston ring
grooves must also be removed.
When fitting new piston rings, the bores must be
lightly honed with a fine-grade emery cloth so that
the new piston rings can become bedded down
properly. The honing should be carried out with an
oScillatory motion up and down the bore until an
even "criss-cross" pattern is achieved. The recom-
mended grade of emery for this purpose is 300.
Thoroughly wash the bores in paraffin (kerosene)
and check that all traces of abrasives are removed.
Pistons and rings are available in 010, 020, 030 and
040 inches. (,254, 508, ,762 and 1016 mm.) over-
sizes. When fitting new rings the gap must be
checked in the lowest part of the cylinder bore.
The ring must lie square to the bore for checking
purposes, and to ensure this. place the piston crown
onto the ring and ease it down the bore. Check the
gap with feeler gauges.
Fig. 820. Refitting a tapered piston ring 37
Piston rings, when new, should have the following
gap clearances:
Compression ring gap: 010" to 014" (25 to 35 mm.)
Scraper ring gap: 010" to 014" (25 to 35 mm.)
R.efitting the piston rings is straight forward, but
check that the two com pression ri ngs are fitted the
right way up.
The two taper compression rings are marked
"TOP" to ensure correct assembly, and should be
fitted with the "TOP" marking towards the
cylinder head (see Fie. B20).
SECTION 824
INSPECTING THE PISTONS AND CYLINDER BORES
PISTONS
Check the thrust areas of the piston skirt for signs
of seizure or scoring.
The piston skirt is of a special oval form and is de-
signed to have limited working clearances within the
bore. The clearances are given In "General Data",
824
Prior to inspection, ensure that both the cylinder
bores and the pistons are clean and free from dirt,
etc. Any deposits of burnt oil round the piston
skirt can be removed by using a petrol (gasolene)
soaked cloth.
ClassicBike.biz
ENGINE
8
NOTE: The top lands of the piston have
working clearance varying from 016 in. to 020
in. and thus allows the top piston ring to be
viewed from above, and the piston to be rocked
slightly. However, this is not critical, it is the
skirt clearances that are all-important.
CYLINDER BORES
The maximum wear occurs within the top
of the bore, whilst the porti..,n below the piston
ring working area remains relatively unworn.
Compare the diameters, measured at right angles to
the gudgeon pin, to obtain an accurate estimate of
the wear. A difference between these figures in
excess of 005 in. (13 mm.) indicates that a rebore
is necessary. Compare the figures obtained with
those given below so that an accurate figure for the
actual wear can be determined.
An approximate method for determining the wear
in a cylinder bore is that of measuring the piston
ring gap at various depths in the bore and com-
paring with the gap when the ring is at the bottom
of the cylinder. The difference between the figures
obtained, when divided by 3 (an approximation
of n) equals the wear on the diameter. As above, If
the difference exceeds 005 ('13 mm.). this indicates
that a rebore is necessary.
SECTION 825
TABLE OF SUITABLE REBORE SIZES
Piston marking
Suitable bore sizes
in. (mm.)
in. mm.
Standard:- 27948 70993
27953 71006
Oversizes:-
,
+010 (254 mm.) 28048 71247
28053 71260
+020 (508 mm.) 28148 71501
28153 71514
+040 (1016 mm.) 28348 72009
28353 72022
SECTION 826
PISTON IDENTIFICATION
1416"
-1424"
1.-____ -' B208
11'1-1
9'0-1
7'5-1
Fig. B21. Piston identification. All measurements taken from the gudgeon pin centre
line to the highest point of the crown
ClassicBike.biz
8
ENGINE
SECTION 827
RENEWING THE SMALL END BUSHES
The small end bush wear, which normally is very
slight, can be estimated when sliding the gudgeon
pin through the bush. If it is in good condition the
pin will be a sliding fit in the bush, with no play
being in evidence.
Renewal of the small end bushes can be easily
achieved by using the new bush to press out the old
one. For this purpose a threaded bolt. about 4 in.
long and a ~ in. long piece of tube with an inside
diameter of t in. will be required.
Place a suitable washer and the new bush onto the
bolt, then offer it into the old bush. Place the piece
of tube and a suitable washer over the bolt and
screw the nut on finger-tight. Centralise the bush
and tube and align the oilway in the new bush with
that in the connecting rod. When the nut is
tightened the new bush will extract the old one.
38
A B
Fig. 822. Extracting a small end bush
Finally, ream the bore of the bush to the size given
in "General Data", taking care not to allow any
metallic particles to enter the crankcase. When
reamering the bush, ensure that its bore is parallel
with the big-end bore.
SECTION 828
REMOVING AND REPLACING THE CONTACT BREAKER
The contact breaker mechanism is housed in the
timing cover on the right ofthe engine and is driven
by the exhaust camshaft. It consists of two sets of
points (one per cylinder), two auxilliary backplates
with cam adjustment and a fully automatic centri-
fugal type advance and retard mechanism. The
working parts are protected by a circular cover
and gasket. The engine oil is prevented from
entering the contact breaker caVity by means of
an oil seal fitted to the inner wall of the timing
cover. The complete contact breaker unit can be
removed from the timing cover with the aid of
service tool 0782.
First, disconnect the leads from the battery
terminals or remove the fuse from the holder
adjacent to the battery, then remove the two
screws and Withdraw the outer cover and gasket.
Remove the centre bolt and screw in service tool
D782 until the cam unit is released from it's locking
taper in the camshaft. Unscrew the tool and remove
the cam unit.
To completely detach the contact breaker unit it
will be necessary to disconnect the two leads from
the ignition coils and remove the appropriatE: frame
826
cljps so that the leads can be withdrawn through
the holes in the crankcase and timing cover.
It is advisable to make a note of the degree
figure which is stamped on the back of the cam
unit, as this indicates the advance range, which
it is necessary to know for accurate static
timing purposes.
Prior to replacing the cam unit it is advisable to add
a small drop of lubricating oil to the pivot pins only,
not the cam pivot. The cam unit slot should be
located on the peg in the camshaft and the centre
bolt screwed in and tightened.
IMPORTANT NOTE: "Run out" on the
contact breaker cam or misalignment of
the secondary backplate centre hole can
result in contact between the cam and back-
plate. This can result in the auto advance
remaining retarded or the spark retarding.
To check for Urun-out" check the point gap
with the contact nylon heel aligned with the
cam scribe mark for each set of points.
Should there be a discrepancy greater then
ClassicBike.biz
ENGINE B
0003 in. tap the outer edge of the cam with a
brass drift with the cam securing bolt tight.
In cases of misalignment of the secondary
backplate hole, check the cam clearance in
different positions and elongate the hole only
where the backplate rubs the cam.
Pillar boll-
Secondary bracket
screw
Black/YelloW
Fig. B23A Contact breaker 6CA
The base plate, on any other than very early
machines with the 6CA contact breaker, should be
assembled with the black/yellow leads rearmost.
Certain early machines afl.er DU.66246 had the
black/white leads to the rear.
To adjust the contact breaker gaps. turn the motor
with the starter pedal until the scribe mark on the
cam aligns with the nylon heel of one set of points.
Measure the point gap using a 0015 in. feeler gauge.
If outside the limits. slacken the contact adjusting
screw, adjust the gap by turning the eccentric
screw, and re-tighten the adjusting screw.
Revolve the motor until the second set of points is
lined up w"lth the scribe line, and adjust as before.
and with the pillar bolts in the centres of the
timing adjustment slots.
CONTACT BREAKER 4CA TYPE
PRIOR TO DU.66246
The base plate should be re-positioned so that the
set of points with the black/yellow lead is rearmost
BLACK 8. YELLOW
B
39
Fig, 823 B Contact breaker 4CA
To adjust contact breaker gaps slacken sleeve
nuts IA'. To rotate contact breaker base plate
for setting ignition timing slacken pillar bolts
'B'.
For earlier models without the peg and slot
arrangement in the cam unit and exhaust camshaft.
the following procedure should be adopted to set
the cam unit in its correct relative position in the
camshaft:-
First set the base plate so that the pillar bolts are In
the centres of their respective slots. then tighten
the pillar bolts. Select 4th (top) gear and remove
the left and right sparking plugs and all four rocker
caps, then turn the engine over until the RIGHT
piston is approximately -k in. (9 mm) before top
centre on its compression stroke (both valves
closed). Turn the contact breaker cam unit until
the REAR set of contact breaker points are just
about to open and tighten the centre bolt. Note
that the cam should be turned clockwise viewed
from the right side of the machine.
Note:- When the correct setting is achieved,
ensure that the contact breaker bolts are tight,
then fit the cover and gasket.
B27
ClassicBike.biz
8 ENGINE
SECTION 829
IGNITION TIMING - INITIAL PROCEDURE
INITIAL ASSEMBLY OF THE CONTACT
BREAKER MECHANISM AND AUTO
ADVANCE UNIT PRIOR TO FINAL
TIMING THE ENGINE
(1) Remove both sparking plugs and all four
rocker box caps. Set the engine at T.D.C. with
both valves closed in the right hand cylinder.
(2) Assemble the auto advance unit into the
exhaust camshaft, locating on the camshaft peg
where it is fitted.
(3) Assemble the C.S. plate, taking care not to
trap the C.S. leads, assembling the plate so
that the C.S. points connected to the black!
yellow leads are located at 7 o'clock. Loosely
assemble the hexagon pillar bolts and fiat
washers.
(4) Lock the auto advance cam into the taper,
using the central fixing bolt.
NOTE: When the degree disc is attached to
the exhaust camshaft, the indicated setting and
advance range will be halfthat ofthe engine, as
the camshaft rotates at half engine speed.
ESTABLISHING TOP DEAD
CENTRE POSITION
Wjlen setting the ignition timing on machines after
engine no. DU.13375, the T.D.C. position can be
qUickly found using workshop tool D571/2. The
blanking plug on top of the crankcase immediately
behind the cylinder block is removed and the body
ofthe tool is screwed into its place. Having removed
both sparking plugs and engaged top gear, rotate
the rear wheel forwards until the pistons are just
coming up towards T.D.C. Then the plunger is
inserted in the body of the tool and the rear wheel
is rotated forwards slowly until the plunger locates
itself in the centre fiywheel. The T.D.C. position
has now been established.
Fig. 824A Showing T.O.C. locating tool in use
IGNITION TIMING USING A STROBOSCOPIC LIGHT
After establishingT.D.C. as desQlJibed in Section S29.
fit the timing disc adaptor shaft and timing disc
into the camshaft auto advance unit and set the
pointer, fixed to a convenient bolt on the engine
to rear T.D.C.
NOTE: When using a stroboscope powered
by 6 or 12 volt batteries as an external power
source, do not use the machine's own battery
equipment. (A.C. pulses in the low tension
machine wiring, can trigger the stroboscope,
and give false readings).
(1) Connect the stroboscope to the right hand
spark plug lead and start the engine. Read the
on the disc, revving the engine up
until the auto advance range is fully achieved.
Check against the correct specification and
adjust the C.S. back plate on its slots until the
correct advanced timing is accurately set.
(2) Repeat for l.H. plug and adjust the accuracy of
the spark on the C.B. points adjustment.
NOTE: To advance the spark, open the
S28A
points, approximately 0001 in. for
each engine degree required, and to
retard, close the points setting similarly.
Minoradjustments to the left cylinder C.B.
points gap setting, to ensure accurate
ignition timing are permissible.
(3) Check back on the stroboscopic reading and
slow tickover for range of advance on both
cylinders. for efficient action of the auto
advance unit, remembering the most important
final setting is at fully advanced, both cylinders.
Timing the engine stroboscopically with a
timing disc ensures that both plugs are firing
at exactly similar angular crank rotation (Le.
piston movement), at fully advanced ignition,
that is at full power, thereby ensuring the
smoothest, most vibration free engine running
condition and ensuring maximum engine power
output.
It also eliminates variations encountered in dif-
fering auto advance ranges due to possible non-
standard components, uneven wear, etc., etc.
ClassicBike.biz
ENGINE 8
SECTION 830
IGNITION TIMING WHERE A STROBOSCOPE IS NOT AVAILABLE
PRIOR TO DU.66246
TO ESTABLISH THE ACCURATE STATIC
IGNITION SETTING
(1) Check the General Data Section for the correct
fully advanced ignition setting for the machine.
(2) Check the auto advance range stamped on rear
of auto advance cam mechanism.
(3) Double the auto advance range and subtract
the figure from the FULL ADVANCE setting
for the machine. This is the correct STATIC
SETTING for the engine.
(4) Use this figure for setting the position of the
C.B. points opening, when assembling the
contact breaker mechanism, using a degree
plate or timing disc attached to the engine.
(5) Convert this figure in degrees tothe equivalent
piston movement B.T.C. if a timing stick is to be
employed.
On machines where an engine camshaft peg
is not fitted, rotate the auto advance mechan-
ism until a position is reached where the rear
set of C.B. points will just commence to open.
CONVERSION CHART-ENGINE DEGREES
TO RELATIVE PISTON POSITION
Crankshaft position Piston position
(B.T.D.C) (B. T.D.C)
Degrees in. mm.
7 015 38
8 020 51
9 025 64
10 030 76
11 038 96
12 045 1-14
13 054 1030
14 060 152
15 068 173
16 077 196
17 087 220
18 09S 2-42
19 108 275
20 120 305
21 135 345
EXAMPLE OF STATIC SETTING
CALCULATION
T120 IGNITION TIMING=39 B.T.C. Fully
C.B. range stamped on auto advance cam=1r.
Twice 12'=24'
Full advance 39'_24'=15' B.T.C. "STATIC
SETTING".
POSITIONING THE TIMING DISC WHERE
THERE IS NO PROVISION FOR THE T.D.C.
PLUNGER (Earlier models)
(1) Fit the timing disc adaptor shaft and timing disc
into the camshaft auto advance unit. and set the
pointer, fixed to a convenient bolt on the
engine, to read T.D.C.
Engage top gear, and use a timing stick with
a suitable mark which aligns along the top of
the cylinder head fins at about 1 in. of piston
movement. (For greater accuracy. use a Dial
Test Indicator through the spark plug hole).
Rotate the engine either side of T.D.C. by
rocking the rear wheel, to exactly the same
measured point of movement on the stick
(or D.T.I.), setting the pointer so that it reads
an equal number of degrees either side of
T.D.C. on the degree disc.
advanced. Fig. B24EEnginefitted with timing disc and dial indicator
8288
ClassicBike.biz
B
ENGINE
STATIC IGNITION TIMING
(TO BE IJSED ONLY WHERE A STROBOSCOPE IS NOT AVAILABLE)
BEFORE DU.66246
("I) Rotate the engine so that the fibre heel of the
C.B. points have just passed beyond the ramp
of the auto advance cam, and just reached
the full open position. Set the point gap
0015 in.
0'015 in.
(0'37mm)
112 R
Fig. B24(a). Setting the contact breaker point gap for
the right cylinder (black/yellow) lead, illustrating
position of the cam where points are just fully open
(2) Rotate the engine "forwards" through 360
0
and set the second set of points in the o r r e s ~
pending positiolT on the cam. Set these points
at a gap of 0015 in.
(3) ROTATE ENGINE AND ESTABLISH AC-
CURATE T.D.C. (See Section B34 prior to
engine number DU.13375 and Section B33 after
this number and prior to DU.66246.
B28C
0015in.
(0'37mm)
112l
Fig. B24(b). Setting contact breaker point gap for the
left cylinder (black/white) lead, illustrating the second
position of the cam, where the points have just achieved
the fully open position
If the machine is put in top gear, small incre-
ments in crank rotation and piston movement
can be achieved by rotating the rear wheel
slowly. and accurate piston T.D.C. established
by "swinging" the engine either side ofT.D.C.
Mark the timing stick at T.D.C. Mark a second
position on the timing stick ABOVE the T.D.C.
mark appropriate to the specified timing for
the machine. i.e. "piston movement before
T.D.C.".
(4) Rotate the engine "backwards" beyond this
mark and then slowly reverse the rotation
"forwards" until the timing mark is set in line
with the top of the cylinder head fins. If a
timing disc is employed. rotate the engine
forwards until the correct "static setting" is
achieved in crankshaft degrees.
ClassicBike.biz
ENGINE
(S) Rotate the e.B. back plate on its slots until a
position is reached where the points just open
(check using a battery and light. or an OOOlS in.
feeler gauge. Alternatively. if a battery is
fitted to the machine and the ignition switch
turned to "IGN", the position where the
points open can be identified by the ammeter
needle giving a "flick" back to zero).
00015 in.
(0'037mm)
1J3R
Fig. B24(a). Contact breaker points just opening on the
right cylinder. With the engine set at the correct
STATIC SETTING, the C.B. back plate assembly
should be adjusted In the slots. to a position where the
C.B. points just commence to open.
e.
B
00015in.
(0'037mm)
113 L
Fig. B24(b). Contact breaker points just opening on the
left cyl inder
Rotate the engine through 360
0
and repeat (4)
above. The other set of e.B. points should
just have opened. If not. the accuracy of spark
on the second set of C.B. points can be cor-
rected by adjusting the points gap.
NOTE: To advance the spark, open the
points, approximately 0001 in. for each
engine degree required, and to retard,
close the points setting similarly. Minor
adjustments to left cylinder C.B. points
setting to ensure accurate ignition timing
are permissible.
B2BD
ClassicBike.biz
B
ENGINE
IGNITION TIMING-INITIAL PROCEDURE AFTER DU.66246
Initial assembly of the contact breaker mechanism
and auto advance uniL prior to final timing of the
engine:-
(1) Remove both sparking plugs and all four rocker
box caps. Set the engine at T.D.C. with both
valves closed in the right hand cylinder.
(2) Assemble the auto advance unit into the
exhaust camshaft, locating on the camshaft peg
where it is fitted.
(3) Assemble the C.B. plate taking care not to
trap the C.B. leads, assembling the plate so
that the C.B. pOints are located at 7 o'dock.
Loosely assemble the hexagonal pillar bolts
and flat washers.
(4) Lock the auto advance cam into the taper
using the central fixing bolt. For static timing
remove the bolt again, taking care not to
release the taper of the cam. Temporarily fit
another washer with a centre hole just large
enough to fit over the cam bearing. thus
allowing the washer to bear hard on the end
of the cam. Rotate the cam carefully to its
limit against the auto advance springs, holding
in this position whilst the centre bolt is re-
fitted and nipped up. The fully advanced
position has then been located.
STATIC TIMING AT3S0 BT DC
WHERE NO STROBOSCOPE IS AVAILABLE AFTER DU.66246
Rotate the engine until the nylon heel of the C.B.
pOints aligns with the scribe marking on the cam.
At this stage set both points gaps to 0015 in.
Locate the crankshaft at 38' B.T.D.C. using the
timing plunger tool D571 modified as shown below.
1
0'246" DIA
__ &:J_O_-----,--:;--___ --i
o
I
1
'49
2!"
2
Fig. B25 Modified timing plunger
l8E
ClassicBike.biz
ENGINE
B
There are three different conditions of flywheel
and crankcase locating holes as shown in Fig. B26
below. Identify the condition relating to the
particular machine being timed. It will be found
easiest to start with the pistons at T.D.C. (checked
through the sparking plug hole) and then, with
both sparking plugs removed and second gear
engaged, rotate the rear wheel backwards. As the
crank is turned by this means, pressure on the
timing plunger will locate it at 38' B.T.D.C.
Remove1:he rocker caps to establish which cylinder
is on the compression stroke (i.e. which cylinder
has both valves ciosed). Note that the timing side
cylinder is operated by the contact points with the
black/yellow lead and the drive side with the
black/white lead.
When it has been decided which cylinder is being
timed, rotate the main contact breaker backplate
on its slots until the particular contact points just
open. This can be checked using a battery and light
or by an 00015 in. feeler gauge between the points.
Alternatively unless the battery has been removed
or disconnected, turn the ignition switch "on"
and the position where the points open can be
identified by the ammeter needle giving a "flick"
back to zero.
Attention should now be turned to the other
cylinder. Remove the timing plunger, turn the
engine forwards through 360" (1 revolution) and
relocate the timing plunger. The second set of
points should now be adjusted as above but the
main backplate must not be disturbed. Adjust
only on the secondary backplate. Finally secure all
screws, lubricate both sides of the cam with Shell
Retinax A grease, replace the cover plate and the
sparking plugs, finaliy engaging neutral gear.
1968 CRANKCASE FLYWHEEL LOCATION (650 'B' RANGE)
B
@
A
B
(fROM ENG. DU66246)
ES871/ E7330 CRANKCASE
1968 MKI.
LOCATING 38 BTDC FROM HOLE ";:;", ,".,,_.J
1968 MK Ii.
LOCATING 38 BTDC FROM HOLE 'A'
AND TDC FROM HOLE 'B'. '
1968 MK III. (DU740S2 ONWARDS)
LOCATING 38 BTDC AND TDC
FROM HOLE 'B'
Fig. 826 Crankcase flywheel location
E7331
FLYWHEEL
ASSY
1968 MKI.
MK.l1
1968 MK III
B28F
ClassicBike.biz
B ENGINE
SECTION B31
IGNITION TIMING BY STROBOSCOPE AFTER ENGINE NUMBER
DU.66245
Undertake the initial procedure as in Section 830
Remove the inspection plate secured by three
screws) from the primary chaincase. As seen in
Fig. B27Athere is a marking on the outer face of
the rotor which is to coincide with an ignition
pointer on the primary chaincase to achieve the
correct 38 ignition timing position.
On machines with the inspection plate on the
primary cover but no provision for the timing
pointer, a special timing plate D2014 is available
and this is shown in Fig. B27B,Note that D2014
has two markings. the one'S' only being used on
650 c.c. applications.
NOTE: When using a stroboscope powered
by a 12 volt battery as on external power
Fig. B27A Rotor marking
B2SG
source, do not use the machines own battery
equipment. (A.C. pulses in the low tension
machine wiring can trigger the stroboscope
and give false readings).
(1) Connect the stroboscope to the right hand
spark plug lead and start the engine. Read
the strobo-light on the rotor marking in
relation' to the timing pointer or timing plate
marking with the engine running at 2,000
R.P.M. or more. Adjust the main backplate
on its slots until the marks align whereupon
the timing on the one cylinder is correct.
(2) Repeat for the L.H. plug and adjust the timing
by slackening off the clamping screw on the
auxilliary backplate and turning the eccentric
screw (see Fig. B23A)until again the markings
align. Timing is then correct. Refit the
primary chaincase inspection plate.
Fig. B278 Timing plate D2e 14
ClassicBike.biz

ClassicBike.biz
8 ENGINE
SECTION 834
EXTRACTING AND REFITTING THE VALVE TIMING PINIONS
Before attempting to remove any of the valve
timing gears it is necessary to release the load on
the camshafts caused by compressed valve springs.
This should be done by removing the rocker boxes
as detailed in Section B2. or may be achieved by
sufficiently slackening the valve clearance adjuster
screws; however, this is not always advisable as it
may result in a push rod becoming disengaged.
Remove the contact breaker as detailed in Section
B28.
I.\.I
Remove the timing cover as described in Section B32
and the oil pump as shown in Section B33. Select 4th
(top) gear. apply the rear brake and unscrew the
nuts retaining the camshaft and crankshaft pinions,
then withdraw the intermediate wheel.
NOTE: The camshaft pinion retainer nuts
have LEFT-HAND threads. The crankshaft
pinion retainer nut has a RIGHT-HAND
thread.
. , . . - - - - ~ . 6150
Fla. 829. Extracting the crankshaft pinion
830
ClassicBike.biz
ENGINE
B
CRANKSHAFT PINION
Removal of the crankshaft pinion is facilitated by
service tool 61-6019. which consists of a protective
cap and three claw extractor body. complete with
extractor bolt.
To extract the pinion, first press the protection cap
over the end of the cran kshaft. then place the
extractor over the pinion, locate the three claws
behind the pinion and screw down the body to
secure them. Using a tommy bar and spanner the
crankshaft pinion can then be extracted (see Fig.
B31). When this is achieved. the key and (clamping
washer if fitted) should be removed and placed in
safe-keeping.
Fig. 830. Extractor tool 616019 showing protection cap
which fits ove.. crankshaft
Refitting the crankshaft pinion is aided by service
tool Z79 which consists of a tubular drift and a gUide.
to ensure correct alignment.
When repladng the clamping washer ensure
that the chamfered side is towards the crankshaft
shoulder. Screw the gUide onto the crankshaft.
Smear the bore ofthe crankshaft pinion with grease
to assist assembly and position it over the guide. so
that the counter bore is outwards. Align the key
and keyway and drive the pinion onto the crankshaft.
CAMSHAFT PINIONS
To facilitate extraction and replacement of both the
inlet and exhaust camshaft pinions, the extractor
and replacement adaptor should be used in con-
junction with the service tool supplied under
assembly number D2213.
Fig. B31. Extracting camshaft pinion using 02213
To extract the pinion, first screw on the extractor
body. then screw In the extractor bolt; the pinion
will then be withdrawn from the camshaft (see
Fig. B31).
In the case of the exhaust camshaft. the adaptor
should be positioned on the end of the camshaft to
avoid damage to the contact breaker location taper.
The location keys in each of the camshafts are a tight
fit, and may be left in position jf it is not intended
subsequently to remove the camshafts from the
crankcase.
When replacing the pinions. first check that the
keys are located correctly, then screw the adaptor
into the assembler bolt and onto the camshaft.
B31
ClassicBike.biz
B
ENGINE
The camshaft pinion should be lubricated to assist
assembly, and the extractor body screwed onto It
(remember that it is a left-hand thread). When this
Is done, slide the pinion and body over the replacer
bolt, align the key and correct keyway and screw on
the replacer nut and washer.
\
L
REFITTING THE INTERMEDIATE WHEEL
Turn the camshafts and crankshaft timing until the
marks are towards the intermediate wheel spindle,
then offer the wheel to the spindle with the timing
marks aligned as shown in Fig. B33, for the particular
model. Fourth gear should then be selected and the
rear brake applied, so that the camshaft and crank-
shaft pinion retainer nuts can be tightened to the
correct torque (see General Data). Reassembly
then continues as a reversal of the above instruc
tions.
'\
04
Fi.. an. Reflttin, the camshaft pinions
632
ClassicBike.biz
ENGINE
B
Fig_ BU. Intermediate wheel location
(1) Exhaust camshaft pinion dot aligned with dot on intermediate wheel.
(2) Crankshaft pinion dot aligned with twin dashes on intermediate wheel.
(3) Inlet camshaft pinion. Dot aligned with:-(a) Long dash for T120 and TR6
(b) Short dash for 6T.
SECTION B35
VALVE TIMING
The valve timing is sufficiently accurate for machines
which are to be used under normal conditions.
when the intermediate wheel is assembled in the
position shown in fig. B33, and the camshaft
pinions are located by means ofthe keyway directly
opposite the timing mark.
It should be noted that, due to the intermediate
wheel having a prime number of teeth, the timing
marks only coincide every 94th revolution, thus
there is no cause for alarm if the timing marks will
not readily re-align.
When checking the valve timing against the
figures given in "General Data" for the
particular model. it should be noted that these
figures are relative to a valve rocker clearance
of 020 in. (5 mm.) for checking only.
B33
ClassicBike.biz
B
ENGINE
SECTION B36
DISMANTLING AND REASSEMBLING THE CRANKCASE ASSEMBLY
6173
Fig. B14. Removing the crankcase junction screws
It is advisable to partially dismantle the engine unit
whilst it is fixed to the motorcycle. then remove the
remaining crankcase assembly and dismantle it on
a work bench.
Proceed as described in Section B1 for removal of
the engine unit. but leave the rear chain connected
and the engine firmly mounted in the frame by
means of the front and bottom engine mounting
bolts. Remove the outer primary cover as shown
underneath the engine (two snap connectors).
Unscrew three nuts securing the stator and with-
draw it from over the mounting studs. Do not try
to withdraw the leads at this stage.
634
Remove the pressure plate and clutch plates as
detailed in Section C4. Select 4th gear and apply
the rear brake, then unscrew the clutch hub
securing nut and extract the clutch hub as shown
in Section C9. When the primary chain has been
threaded over the stator the sleeve nut should be
unscrewed and the stator leads withdrawn.
Remove the gearbox outer cover and dismantle the
gearbox (see Section D) then remove the rocker
boxes, cylinder head, block and pistons as shown
in Sections B2, B14, B19 and B22 respectively, then
disconnect the control cable(s) and remove the
carburetter(s).
ClassicBike.biz
ENGINE B
Remove the contact breaker, timing cover complete
with oil switch and oil pump (Sections B2S. B32 and
B33) then extract the crankshaft pinion. If it is
required to inspect or change the camshafts or
bushes. the camshaft pinions should also be
extracted.
Remove the front and bottom engine mounting
studs, disconnect the rear chain and remove the
crankcase assembly.
Remove the crankcase filter and oil way blanking
plug located at the bottom of the crankcase in line
with the oil pump. and catch any oil that may be
present in the crankcase.
Grip the crankcase firmly in a vice by means of the
bottom mounting lug and unscrew the three bolts
and the two screws shown in Fig. B34, then remove
the remaining four studs and unscrew two nuts
adjacent to the gearbox hOUSing. The crankcase-
halves may now be parted using extractor tool
No. 61-6064. When the halves are apart. with-
draw the crankshaft assembly and store it carefully.
then remove the rotary breather valve from within
the inlet camshaft bush in the left half-crankcase.
Fig. 835. Parting the crankcase halves
using service
Thoroughly dean and degrease the crankcase paying
particular attention to the oilways. DO NOT
DAMAGE the scavenge pipe to crankcase joint.
REASSEMBLY
Prior to reassembly. the junction surfaces should be
carefully scraped dean. giving special attention to
the location spigot and dowels. Replace the oilway
blanking plug located at the bottom of the RjH
crankcase in line with the oil pump. and crankcase
filter.
Mount the left half-crankcase on its side on two
wooden blocks. or a bench with a hole in for
crankshaft clearance. lubricate the main bearings
and camshaft bushes. Place the rotary breather
valve and spring into the camshaft bush. then
assemble both camshafts ensuring that the slot In
the end of the inlet camshaft engages the projection
of the breather disc valve. Assemble the crankshaft
into position ensuring that it is right home in the
bearing by giving it a sharp blow with a hide mallet.
Note that the crankshaft is located to the timing
side.
Apply a fresh coat of jointing compound to the
junction surface of the left half-crankcase then
lubricate the main bearings and camshaft bushes in
both halves of the crankcase. Position the con-rods
centrally and lower the right half-crankcase into
pOSition over the crankshaft. Wh,?n the halves are
mated. check the crankshaft and camshafts for
freedom of rotation. The crankshaft should revolve
freely whilst the camshafts should offer little or no
resistance to rotation by hand.
Refit the crankcase securing bolts and studs. and
tighten them until they are just "pinched-up".
Check that the cylinder block junction surface of
the crankcase is level.
If there is a slight step between the two halves. this
should be corrected by tapping the front and rear
of the crankcases as required, until a level surface is
achieved. The crankcase securing bolts should then
be tightened, a turn at a time, to the torque figures
given in "General Data". The bolts arrowed in
Fig. B34 should be tightened first. then the two
inner screws, and so on.
Reassembly then continues as a reversal of the
dismantling instructions, Prior to refitting the
cylinder block. pour i pint of oil into the crankcase.
B35
ClassicBike.biz
8 ENGINE
SECTION 837
STRIPPING AND REASSEMBLING THE CRANKSHAFT ASSEMBLY
Grip the crankshaft conveniently in a suitable vice
and place rag over any sharp edges to avoid the
connecting rods becoming damaged. Mark the
connecting rods, caps and crankshaft so that they
can be replaced in their original positions.
SLUDGE
SECTION 'xY
NOTE: The connecting rod, cap and nut are
centre punched on initial assembly so that the
cap may be refitted correctly relative to the
connecting rod.
8194
Fig. 836. Sectional view of crankshaft-showing 011 tube
836
ClassicBike.biz
ENGINE
B
Unscrew the cap retainer nuts, a turn at a time to
avoid distortion. then remove the caps and con-
necting rods. Refit the nuts to their respective
bolts to ensure correct reassembly.
Using a large Impact screwdriver, unscrew the oil
tube retainer plug from the right end of the big-end
journal. If difficulty is encountered, drill a i in. dia.
hole to t in. depth in the crankshaft, to remove the
centre punched indentation which locks the oil
tube retainer plug in position.
Unscrew the flywheel bolt adjacent to the big-end
journal, then withdraw the oil tube using a hooked
rod located in the flywheel bolt location hole (see
Fig. 836).
Thoroughly clean all parts in paraffin (kerosene)
then clean the oil drillings using a jet of compressed
air. Particular attention should be given to checking
that each oil drilling Is free from blockage.
To remove the flywheel. unscrew the remaining two
bolts and press out the crankshaft, using a press
which can give a load of up to 5 tons. (Ensure that
there Is a centre punch mark on the RIGHT side of
the flywheel before removing; this enables the
flywheel to be replaced in its original position).
Replacing the flywheel is best done when the oil
tube is correctly located in position. Offer the oil
tube into the crankshaft with the flywheel bolt
holes in the tube and crankshaft aligned. Insert a
flywheel bolt temporarily to locate the oil tube In
position.
Tightly screw in the plug and centre punch the
crankshaft opposite the slot so that the plug is
locked in position.
To re-assemble the flywheel it should be heated to
100C., then placed over the crankshaft (which
should be cold) with the centre punch mark to the
RIGHT. It will be necessary to turn the flywheel
through 180 to get it over the crankshaft web.
Turn it to its correct pOSition relative to the
crankshaft as soon as this is achieved, and align the
bolt holes.
The flywheel bolts should be tightened to the
torque figure given in "General Data" using a small
amount of proprietary sealant such as "TRIUMPH
LOCTITE" to obviate any possibility of the bolts
working loose.
If a new or re-ground crankshaft or a new flywheel
has been fitted, the assembly should be re-balanced,
'I
-i
I
I
B246
Fig. B37. Balancing the crankshaft
(to an 85% balance factor) using two service balance
weights Z138 (689 gms. each) for both flywheel con-
ditions. Place the assembly on true horizontal knife
edges, resting it on the left and right main bearing
diameters. Allow the assembly to come to rest.
then mark the lowest point of the flywheel with
chalk. Turn the assembly through 90 and if it
returns to the same position drill a tin. dia. hole
centrally, adjacent to the chalk mark, to a depth of
apprOXimately tin.
Repeat the balanCing procedure again making a
chalk mark as necessary, and drill further holes
until the assembly will come to rest in any position
when placed on the knife edges. The drilled holes
should have a distance of approximately i in.
between centres.
Finally, thoroughly wash the assembly in paraffin
(kerosene) and check that the oil-ways are free
from blockage.
B37
ClassicBike.biz
B ENGINE
SECTION B38
REFITTING THE CONNECTING RODS
First, ensure that the connecting rod and cap and
both the front and rear of the beari ng shells are
scrupulously clean. then offer the shells to the rod
and cap and locate the shell tabs into their respective
slots. Smear the bearing surfaces with oil and refit
the rod and cap to their original journals. ensuring
that the centre punch marks are aligned and that
the tab location slots are adjacent (see Fig. B38).
Refit the bolts and screw on the nuts to the given
torque figure.
On the very latest machines. centre punch marks
are no longer used on the connecting rod nuts and
on both these models and earlier ones with centre
punch marks we now prefer the use of a torque
wrench, to tightening to bolt extension as in
previous instructions.
Finally. force oil through the drilling at the right end
of the crankshaft with a pressure oil can until it is
expelled from both big-end bearings. thus Indicating
that the oil passages are free from blo<kage and
full of oil.
Fi,. B38. Refitting the connecting rods
CRANKSHAFT LOCATION
Machines from DU.24875 onwards have the c r n k ~
shaft located to the timing side as was the ca!:.e
between engine numbers DU.101-DU.13374.
Machines between DU.13375 and DU.24874 had the
crankshaft located to the drive side.
B38
If such a machine was equipped with the roller drive
side main bearing it would be necessary to fit also
the timing pinion and clamping washer as shown in
the No.6 SPARE PARTS CATALOGUE.
ClassicBike.biz
ENGINE
B
SECTION B39
INSPECTING THE CRANKCASE COMPONENTS
In preparation for Inspection. thoroughly clean the
crankcase-halves, main bearings. crankshaft and
connecting rods. etc . in paraffin (kerosene) and
allow them to drain. If there Is an air pump
accessible. then dry the components with a jet of
compressed air and examine them as follows:-
(1) BIG-END BEARINGS
The extent of wear to the big-end journals can
be determined by inspecting the bearing
surfaces for scoring and by measuring the
diameter of the journals. light score marks
can be reduced with smooth emery cloth but
ensure that all parts are carefully washed after
this operation.
Where a journal has been slightly scored the
big-end shell bearings should be renewed. If
the scoring and wear is extensive the big-end
journals should be reground to a suitable size
as given below.
NOTE: The replaceable white metal big-
end bearings are pre-finished to give the
correct diametral clearance. Under no
circumstances should the bearings be
scraped or the connecting rod and cap
joint faces filed.
Suitable crankshaft size
Shell bearing marking
in. mm.
Standard:- 16235 41237
16240 41250
Undersize:-
-010 1-6135 40983
16140 40996
-020 16035 40n9
16040 40742
Service reground crankshafts are obtainable
from a TRIUMPH dealer or in the U.K. from
the TRIUMPH ENGINEERING CO. LTD .
SERVICE DEPARTMENT.
(2) MAIN BEARINGS
Clean the bearings thoroughly in paraffin
(kerosene). then dry them with a jet of com-
pressed air. Test the bearing for roughness by
spinning. Check the centre race for side-play
and inspect the balls and tracks for any signs
of indentation and pocketing. Examine the
main bearing diameters on the crankshaft for
wear. The bearings should be a tight push fit
on the crankshaft and a press fit in the crank-
case. A loose fitting bearing would tend to
cause crankcase "rumble", The correct
diameters of the main bearing journals are
given in "General Data",
(3) CAMSHAFTS AND BUSHES
The camshaft bushes normally show very little
sign of wear until a considerable mileage ha.s
been covered. A rough check on the wear can
be made by inserting the camshaft into the
bearing and feeling the up and down movement.
An exact check can be made by measuring the
camshaft with a micrometer and measuring the
camshaft bushes with calipers. The working
clearance figures are given in "General Data".
Wear on the cam form will be mainly centred
on the opening flank of the cam and on the
lobe of the cam. Particular attention should
be given to these areas when examining the
cam form for grooving. In a case where there
is severe grooving the camshaft and tappet
followers should be renewed.
A method of estimating the extent of wear on
the cam form is that of measuring the o v e r ~ l l
height of the cam and the base-circle diameter.
The difference is the cam lift. If all other
aspects of the camshaft are satisfactory and the
wear on the cam form does not exceed
0010 in . then the camshaft may be used for
further service.
(4) CRANKCASE FACES AND DOWELS
Ensure that the faces of the crankcases are not
damaged in any way and that any dowels are in
position, particularly the metering dowel on
the timing cover face near the pressure release
valve. The dowel is counter bored, incorporates
a metering pin. and should be assembled with
the larger hore outermost.
B39
ClassicBike.biz
8
ENGINE
SECTION 840
RENEWING THE MAIN BEARINGS
Fi,. B39. Oil seal-left half-crankcase
The oil seal can be removed from the left half-
crankcase by driving it outwards, in the opposite
direction to the bearing after the bearing is
removed. It is advisable to renew the oil seal,
even if it does not appear badly worn.
To remove the timing side ball journal bearing
heat the crankcases to approximately 100C and
drive the bearing inwards using service tool Z14.
Alternatively, a suitable drift can be made from a
piece of 1* in. diameter mild steel bar, about 6 in.
long by turning it to 1!- in. diameter for t in. at one
end.
On the drive side roller bearing the inner portion
will be withdrawn with the crankshaft. The outer
spool however will still involve heating the crankcase
840
and if it is very tight in the case will require the use
of special tool Z162 which expands to grip the outer
spool.
To assemble the new bearings first ensure that the
main bearing housing is clean. then heat the crank-
case to approximately 100C. and drive in the
bearing using a tubular drift onto the outer race.
Ensure that the bearing enters its housing squarely.
If possible, use a press. Suitable dimensions for the
drift are 2* in. outside diameter x 6 in. long.
When the bearings are in position, press the oil seal
into place in the left half-crankcase (see Fig. B'9).
The roller drive side bearing could be fitted to
advantage on earlier machines. The roller bearing
will be a direct replacement prior to Engine No.
DU.13375. If fitted to machines between Engine
Nos. DU.13375 and DU.24874 the crankshaft pinion
and clam p washer must be changed to locate the
crankshaft from the R.H. main bearing. The
necessary parts are listed in the No.6 replacement
Parts Catalogue.
Fig. B40. Roller main bearing
ClassicBike.biz
ENGINE
B
SECTION B41
RENEWING CAMSHAFT BUSHES
To remove the camshaft bushes in the RIGHT
half-crankcase heat the crankcase to 100C, and
drive the bush out from the outside. using a suitable
drift. While the crankcase is still hot, drive in the
new bush, ensuring that the oil feed hole in the
bush and the crankcase drilling are aligned. A
suitable drift for this purpose can be made from a
6 in. long piece of M.S. bar of 1, in. diameter, by
machining a pilot on one end i in. diameter x 1 in.
long.
To remove the camshaft bush from the LEFT half-
crankcase, a tap is necessary. An ideal size is i in.
diameter x 9 Whit. When a good thread has
been cut in the old bush, heat the crankcase
(100c') and screw in a suitable bolt. Grip the bolt
in a vice and drive the crankcase with a hide mallet
until the bush is removed. Do not attempt to lever
the bush out of position with the bolt, or the case
. may be damaged. If the tap is used in place of the
bolt, care must be taken not to give too hard a
knock to the crankcase or the brittle tap may break.
Retained behind the inlet camshaft bush is the
breather valve porting disc, which is located by
means of a peg. When renewing the bush ensu re
that the disc is located correctly on the peg.
The sintered bronze camshaft bushes are machined
to size before pressing in, therefore only the
smallest amount of metal will need to be removed
when they are renewed. See "General Data" for
reaming sizes and working clearances.
When reaming is completed. the crankcase must
be thoroughly washed in paraffin (kerosene) and
allowed to drain. Preferably. use a jet of compressed
air to ensure that all swarf is removed.
SECTION B42
REMOVING AND REPLACING THE TACHOMETER DRIVE
Where the optional tachometer is fitted. there is a
right angled drive gearbox as shown in Fig. B41.
It is not necessary to part the crankcases to remove
the drive gearbox. When the large slotted end cap
is removed and the engine turned over qUickly the
drive gear should be ejected. If this is not so, the
gear can be withd rawn with long-nosed pliers. The
left-hand threaded centre bolt holding the drive
gearbox to the crankcase will then be seen. A .3
6
in.
Whitworth thin box spanner is needed to release
this and the box will then come away from the
crankcase. The driven gear housing is secured by
a locking pin and is a relatively tight fit. See Fig. B41.
It will be noted that a spade in the back of the
tachometer gearbox slots into a 'thimble' which is
permanently fitted into the end of the exhaust
camshaft.
Fig. 841. Exploded view of tachometer gearbox.
B41
ClassicBike.biz
B
ENGINE
Fig. 846. Tachometer drive gearbox
The reassembly procedure for the drive gearbox is
a reversal of the above.
Earlier machines had a simple spade and abutment
which could if required be replaced by the right-
angled drive used after engine number DU.24875.
This would necessitate fitting also the later
tachometer head and cable.
On U.S.A. market machines a "Stat-aSeal" washer
is used between the crankcase and tachcmeter
gearbox. On such machines the seal should be
renewed whenever the tachometer gearbox is
removed and refitted.
If for any reason the tachomett:r drive thimble in
the exhaust camshaft is displaced or damaged. this
can be replaced with a speCial drive plug E70S0
without dismantling the engine. To fit the plug,
remove the 'tachometer drive gearbox or cable
adaptor from the crankcase and using a tin,
diameter punch. drive the old thimble at least an
inch back into the exhaust camshaft. If possible
retrieve the broken off ears of the old thimble
with a magnet. Thread the new drive plug through
the tachometer drive hole in the crankcase and
into the camshaft as far as possible. Finally make
up a drift as below and drive the new plug into
the camshaft until it is just flush with the end of
the shaft. Take care that the drive plug is not
driven too far in as the drive blade must engage
adequately.
This face must be
square with the
axis of the drift.
I- At least 5 - - - - ~ 1 ~
~ I -------------.-1
11
%"
t
Fig. 851. Drive plug drift
842
ClassicBike.biz
SECTION C
TRANSMISSION
DESCRIPTION
ADJUSTING THE CLUTCH OPERATING MECHANISM
ADJUSTING THE PRIMARY CHAIN TENSION
REMOVING AND REPLACING THE PRIMARY COVER
REMOVING AND REFITTING THE CLUTCH PLATES ...
INSPECTING THE CLUTCH PLATES AND SPRINGS
ADJUSTING THE CLUTCH PRESSURE PLATE
RENEWING SHOCK ABSORBER RUBBERS
REMOVING AND REPLACING THE STATOR AND ROTOR
REMOVING AND REPLACING THE CLUTCH AND ENGINE SPROCKETS
INSPECTION OF THE TRANSMISSION COMPONENTS
REAR CHAIN ALTERATIONS AND REPAIRS ...
Section
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
C1
ClassicBike.biz
C TRANSMISSION
Fig. C1. General arrangement of clutch and shock absorber unit
DESCRIPTION
The dutch is of a multiplate type. using synthetic
friction material on the bonded drive plates and
incorporating a transmission shock absorber. The
pressure on the clutch plates is maintained by three
springs held in position by three slotted nuts.
The clutch is designed to operate in oil and it is
essential that the oil level in the chaincase is main-
tained, otherwise the bonded segments of the driven
clutch plates may burn and disintegrate under
heavy loading. Always use the recommended grade
of oil (see Section A2). If a heavier grade of oil is
used the dutch plates will not readily separate
when disengaged. which will cause a certain amount
of difficulty when changing gear due to dutch drag.
The shock absorbing unit transmits the power from
the clutch sprocket via the dutch plates to the
gearbox mainshaft. Within the shock absorber unit
the drive is transmitted through three large rubber
pads to the three-armed spider which is splined to
the clutch centre; this in turn is located to the
gearbox mainshaft by means of a locking taper and
key. In addition, there are three rubber rebound
pads. The total effect ofthe rubber pads is to reduce
the variations in engine torque at low speeds,
providing an extremely smooth transmission of
power to the gearbox.
SECTION CI
ADJUSTING THE CLUTCH OPERATING MECHANISM
The clutch. which is situated within the outer
primary cover on the left of the machine, can
be adjusted by means of the handlebar adjuster.
push rod adjuster and the pressure plate springs,
the latter only being accessible for adjustment when
the outer primary cover is removed. Section C4
fully describes adjusting the springs and pressure
plate.
The clutch operating rod should have n. inches
(1'5 mm.) clearance between the clutch operating
mechanism and the pressure plate. To achieve this
remove the inspection cap from the centre of the
C2
primary cover. then slacken the clutch cable
handlebar adjustment right off.
Unscrew the hexagonal lock nut and screw in the
slotted adjuster screw in the centre of the pressure
plate until the pressure plate just begins to lift.
Unscrew the adjuster one full turn and secure it in
that position by re-tightening the lock-nut.
The clutch operating cable should then be re-
adjusted. by means of the handlebar adjuster. until
there is approximately t inches (3 mm.) free move-
ment in the cable.
ClassicBike.biz
TRANSMISSION C
Fig. C2. Exploded view of clutch operating
mechanism DU.66246 onwards
Fig. Cl. Exploded view of clutch operating
mechanism up to DU.66246
If the clutch is dragging and normal adjust.ment of
the operating rod and operating cable produces no
improvement. it will be necessary to remove the
outer primary cover and check the pressure plate
for true running as shown in Section C6.
Maladjustment of the clutch operating mechanism
can be symptornised by a loud "dIck" when
operating the clutch lever or on machines prior to
DU.66246. the clutch cable becoming disconnected
at the connector where the cable nipple joins the
dutch mechanism operating spoke. In the former
case adjustment of the clutch operating mechanism.
as detailed above, will eliminate the neise. On
earlier machines in the case where the clutch cable
becomes disconnected at the gearbox, the clutch
cable nipple and the spoke connector should be
examined and renewed if necessary. This trouble
may recur unless the adjustment procedure, as
given above. is carefully followed. Full details of
removal of the clutch operating mechanism are
given in Section D6.
To maintain a smooth and easy clutch operation,
particular attention should be given to the recom-
mended primary chaincase oil change periods (see
Section A1) and clutch cable lubrication (see
Section A18).
SECTION C2
ADJUSTING THE PRIMARY CHAIN TENSION
The primary chain is of the Duplex type and is
non-adjustable as the centres of the engine main-
shaft and gearbox mainshaft are fixed. Provision for
take-up of wear in the primary chain is made by
means of a rubber faced tension slipper blade below
the lower run of the chain. The free movement in
the chain can be felt with the finger after removing
the top inspection plug adjacent to the cylinder
block, with the engine stopped, of course.
The correct chain adjustment is i in. (95 mm.) free
movement. To adjust the chain tension first place
a drip tray underneath the chaincase and unscrew
the hexagonal pillar bolt adjacent to the centre
stand left hand lug. On some earlier models it may
be necessary to loosen the left footrest to give
sufficient clearance. To do this unscrew the foot-
rest securing nut and tap the footrest in a down-
ward direction to release it from its locking
taper.
FiS' C3.
'r--.. ~
Adjustins the chain tensioner - - - ~
C3
ClassicBike.biz

ClassicBike.biz
TRANSMISSION
C
SECTION C4
REMOVING AND REFITTING THE CLUTCH PLATES
Remove the outer primary cover as described in
Section Cl.
The three pressure plate springs are locked In
position by means of location "pips" in the cups
and on the drive adjuster nuts. To facilitate removal
of the slotted adjuster nuts. insert a knife blade
under the head of the nut whilstthe nut Is unscrewed
(using a screwdriver of the type shown in Fig. C5).
Withdraw the springs. cup and pressure plate
assembly. Removal of the clutch plates is facilitated
by means of two narrow hooked tools which can be
made from a piece of n in. dia. wire by bending to
form a hook at one end. Thoroughly clean all parts
in paraffin (kerosene) and inspect the clutch springs
and plates for excessive wear (see section C5).
When replacing the clutch plates remember that
the bottom position is occupied by a bonded plate.
Fig. CS. Unscrewing the clutch spring nuts
Ensure that the cups are located correctly and
assemble the springs and nuts. then adjust the
pressure plate for true running as described below.
Reassembly then continues as the reversal of the
above instructions.
SECTION CS
INSPECTING THE CLUTCH PLATES AND SPRINGS
The bonded friction plates should be examined for
excessive wear to the driving tags and the overall
thickness of the clutch plates should be measured to
determine the wear to the friction faces. If the
reduction In thickness is more than 030 in.
(75 mm.) when checked against a new plate the
plate should be renewed. Check the fit of the driv-
ing tags in the clutch housing. The clearance should
not be excessive.
Check the plain steel driven plates for fiatness by
placing the plates horizontally on a perfectly fiat
surface such as a thick piece of plate glass.
Original finish on the driven plates is a phosphoric
acid etched surface and hence the plates need not
be polished. Check the fit of the plate on the shock
absorber housing. The radial clearance should not
be excessive.
Inspect the clutch springs for compressive strength
by measuring the length of the spring and comparing
it with the dimensions given In "General Data",
If a spring has shortened more than 01 in. (25 mm.)
the complete set should be renewed. It is not
advisable to renew just one or two springs as this
may ultimately result in the pressure plate running
unevenly.
CS
ClassicBike.biz
C TRANSMISSION
SECTION C6
ADJUSTING THE CLUTCH PRESSURE PLATE
When the pressure plate is refitted or requires
adjustment, the following procedure should be
observed. With neutral selected, sit astride the
machine, disengage the clutch, then depress the
kickstart-pedal and observe the rotation of the
pressure plate; it should revolve true relative to
the clutch housing. If it does not do so, .the three
slotted nuts must be initially adjusted so the ends
of the clutch pins are flush with the heads of the
nuts. The nut is prevented from unscrewing by a
"pip" on the underside and to unscrew a nut, a
narrowscrewdriver should be used to hold the spring
away from the "pip" of the nut as shown in Fig. CS.
When the nuts are flush with the ends of the pins
depress the kickstart again and mark the "high-
spot" with chalk, then screw in the nearest nut(s)
about half a turn and try again. Repeat this pro-
cedure until the plate rotates evenly without
"wobbling",
SECTION C7
RENEWING SHOCK ABSORBER RUBBERS
When the primary cover and clutch plates are
removed, access is gained to the shock absorber
unit. which consists of a housing, paddle or spider,
inner and outer coyer plates and shock absorbing
rubbers.
To remove the rubbers for inspection or renewal,
first unscrew the three screws which serve to
retain the shock absorber cover plate and lever the
plate free. using a suitable small lever.
The shock absorber rubbers can be prised out of
position. using a sharp pointed tool. commencing
by levering out the smaller rebound rubbers first.
When the three small rebound rubbers are re-
moved the large drive rubbers will be free to be
withdrawn.
If the rubbers show no signs of punctures or
cracking, etc., they can be refitted. but remember
that a slight puncture in the rubber can ultimately
result in the rubber disintegrating.
C6
Fig. C6. Replacing the shock absorber rubbers
ClassicBike.biz
TRANSMISSION C
To replace the shock absorber drive and rebound
ru bbers, first install all three of the larger drive ru b-
bers in position as shown in Fig. C6. Follow through
by inserting and replacing the smaller rebound
rubbers. It may prove necessary to lever the shock
absorber spider arms using a small tommy bar or
similar to facilitate assembly. but this operation
can be accomplished 'in situ' on the machine
without the need for special tools or equipment,
or necessity for removing the complete unit from
the machine.
Although the rubbers are of an oil resistant type,
It is not advisable to use oil or grease as an aid to
reassembly as this may shorten the working life of
the rubber.
Ensure that the three shock absorber outer cover
screws are tight. Use a screwdriver that engages
the complete length of the screw slot. Apply
Triumph "LOCTITE"to the screw threads before
final assembly.
SECTION C8
REMOVING AND REPLACING THE STATOR AND ROTOR
First disconnect the stator leads from underneath
the engine (two snap connectors or three on earlier
models) then, with the primary cover removed,
unscrew the three stator retaining nuts and with-
draw the stator from over the mounting studs and
withdraw the lead from the sleeve nut. If any
difficulty is encountered. unscrew the sleeve nut and
the lead can then be withdrawn easily. To remove
the rotor unbend the tab washer and unscrew the
mainshaft nut using a box spanner and mallet, or,
alternatively, select 4th (top) gear and apply the
rear brake, then unscrew the nut.
Check the rotor carefully for signs of cracking or
fatigue failure.
When replacing the rotor ensure that the key is
located correctly, then tighten the nut to the torque
figure given in "General Data".
When refitting the stator, ensure that the side of
the stator with the leads connecting the coils
together is outermost, then tighten the retaining
nuts to the torque figure given in General Data
Section. Insert the lead into the sleeve nut and
connect the three wires to those of the same colour
code underneath the engine. Check that the
position of the lead is such that it cannot foul the
chain.
Finally, rotate the crankshaft and ensure that the
rotor does not foul the stator. It should be possible
to Insert a feeler gauge of 0008 in. (02 mm.)
thickness between each of the stator pole pieces
and the rotor.
Fil. C7. Showinl stator location on crankcase
C7
ClassicBike.biz
C TRANSMISSION
SECTION C9
REMOVING AND REPLACING THE CLUTCH AND ENGINE SPROCKETS
Remove the primary cover as shown in Section C3,
then remove the pressure plate and clutch plates,
as shown in Section C4. Insert the locking plate Z13
into the clutch housing and remove the stator and
rotor as described in Section ca. Remove the
rotor key and distance piece and slacken off the
chain tensioner. Unscrew the clutch hub self
locking securing nut then remove the cupped
washer. (Machines before DU.48145 have a plain
nut and tab washer).
As the primary chain is of the endless type. the
clutch and engine sprockets have to be extracted
simultaneously using extractor D622(3 and extractor
tool Z151 as shown in Figs. C8 and C9 (machines
before DU.48145 use clutch extractor DA50(1).
Fig. C8. Extracting the clutch centre, using extractor
0662,3 and locking plate Zll
Screw the body of the clutch extractor into the
clutch hub until the maximum depth of thread is
e n ~ a g e d then tighten the centre bolt until the hub
is released. When this is achieved. assemble the
C8
engine sprocket extractor, No. Z1S1. and screw
in the centre bolt and extract the engine sprocket.
",\',1 \'
. ,
51
Fi8. C9. Extracting the engine sprocket, using service
tool Z151
Press out the hub from the shock absorber to
release the sprocket, thrust washer. rollers and
threaded pins.
Finally. remove the key from the gearbox mainshaft
and check that the oil seal in the primary chain
inner cover is a good fit over the high gear. To
renew this oil seal the circular cover should be
removed. When replacing the cover, use a new
paper gasket and ensure that the 011 seal Is pressed
in with the lip relative to the cover as shown in
Fig. C10.
Note that on current models the actual'nose' of the
high gear has been extended and the cover and
centre seal increased in diameter to suit. Seals,
covers and high gears are only interchangeable as a
set.
ClassicBike.biz
TRANSMISSION c
22
Fig. C10. Oil seal in gearbox sprocket detachable
cover
inspect them for wear or fatigue as shown in
Section C10.
Grease the clutch hub and fit the thrust washer and
20 of the correct rollers.
Do not use * in. X * in. bright ended rollers.
Place the sprocket in position and press on the
shock absorber complete with the three threaded
pins. If the splines are loose use Triumph
"LOCTITE".
When replacing the primary chain and sprockets,
ensure that the taper ground boss of the engine
sprocket is towards the crankshaft main bearing and
the oil seal. With the gearbox mainshaft key car.-
fully in position, locate the clutch hub onto the
mainshaft taper and tap it slightly to lock it onto the
taper.
Place the primary chain over the engine sprocket
and drive the sprocket onto the crankshaft.
Offer the clutch locking tool Z13 into the clutch
plate housing and then refit the cup washer, tab
washer and cI utch secu ri ng nut.
NOTE: The cup washer fits with the cup side
out and the tab washer fits with the long tab
located in the hole in the bore of the shock
absorber spider.
On machines after DU,48144 the cupped washer,
tab washer and nut are replaced by a modified
cupped washer and self locking nut.
Engage fourth gear, apply the rear brake and tighten
the clutch securing nut to the torque figure given
in "General Data",
Do not forget to fit the distance piece between the
engine sprocket and rotor and remember to refit
the rectangular section rotor locating key. Re-
assembly then continues as a reversal of the above
instructions. Finally, replenish the chaincase with
the recommended grade of oil (see Section A2).
Note.-Alternatively, the clutch sproc"ot may be
removed by prising out the twenty roller bearings
and allowing the sprocket to move both outwards
and forwards until it can be unmeshed from the
primary chain. This alternative only applies if the
shock absorber assembly can readily be detached
from the hub to allow access to the rollers.
C9
ClassicBike.biz
C TRANSMISSION
SECTION CIO
INSPECTION OF THE TRANSMISSION COMPONENTS
(1) Inspect the primary chain for excessive wear of
the rollers and pivot pins and check that the
elongation does not exceed 11%' To do this
first scribe two marks on a flat surface exactly
12 in. (305 em.) apart, then after degreasing or
washing the chain in paraffin (kerosene), place
the chain opposite the two marks. When the
chain is compressed to its minimum free
length the marks should coincide with the
centres of tv.o pivot pins 32 links apart. When
the chain is stretched to its maximum free
length the extension should not exceed * in.
(625 mm.).
Inspect the condition of the sprocket teeth for
signs of hooking and pitting.
A very good method of indicating whether the
chain is badly worn or not is to wrap it round
the clutch sprocket and attempt to lift the
chain from its seating at various points round
the sprocket. Little or no lift indicates that
both the sprocket and chain are in good
condition.
(2) Check the fit between the shock absorber spider
and the clutch hub splines. The spider should
be a push fit onto the clutch hub and there
should not be any radial movement.
C10
Similarly check the fit of the engine sprocket
splines onto the crankshaft. Again. there
should not be any radial movement.
If either the spider or the engine sprocket are
tight fitting on the clutch hub and crankshaft
respectively, there is no cause for concern as
such a fit is to the best advantage.
(3) Check the clutch hub roller bearing diameter,
the rollers themselves and the be.ring of the
clutch sprocket for excessive wear and pitting
etc. Measure the rollers, clutch hub and clutch
sprocket bearing diameters and compare them
with the dimensions given in "General Data".
If the di.meters of the rollers are below the
bottom limit, they should be renewed. When
purchasing new rollers ensure that they are in
accordance with the dimensions given in
"General Dat .... In particular, check th.t the
length is correct.
(4) Check that the shock absorber spider is a good
working fit in the inner and outer retaining
plates .nd that the arms of the spider h.ve not
caused excessive score marks on the inner
faces of the retaining plates. A good idea is to
check the working cle.rance by assembling
the shock .bsorber unit without the rubbers.
(5) Inspect the clutch operating rod for bending,
by rolling it on a flat surface such as a piece of
plate glass. Check that the length of the rod
is within the limits given in "General Data".
This component should not be replaced with
anything other than a genuine Triumph spare
part. The ends of the rod .re specially heat
treated to give maximum wear resistance.
ClassicBike.biz
TRANSMISSION C
SECTION ell
REAR CHAIN ALTERATIONS AND REPAIRS
If the chains have been correctly serviced. very few
repairs will be necessary. Should the occasion arise
to repair. lengthen or shorten a chain. a rivet
extractor. as shown in Fig. C13. and a few spare
parts will cover all requirements.
To SHORTEN a chain containing an EVEN NUMBER
OF PITCHES remove the dark parts shown in (1)
and replace by cranked double link and single
connecting link (2).
To SHORTEN a chain containing an ODD NUMBER
OF PITCHES remove the dark parts shown in (3)
and replace by a single connecting link and inner
link as (4).
4 ) ~
To REPAIR a chain with a broken roller or inside
link. remove the dark parts in (5) and replace by
two single connecting links and one inner link as (6).
125
Fl.. cn. Rear chain alterations
RIVET EXTRACTOR (PART NUMBER 167)
The rivet extractor can be used on all motorcycle
chains up to ! in. pitch, whether the chains are on
or off the wheels.
When using the extractor:-
(1) Turn screw anti-clockwise to permit the punch
end to clear the chain rivet.
(2) Open the jaws by pressing down the lever (see
below).
(3) Pass jaws over chain and release the lever.
Jaws should rest on a chain roller free of chain
link plates (see below).
(4) Turn screw clockwise until punch contacts and
pushes out rivet end through chain outer link
plate. Unscrew punch. withdraw extractor and
repeat complete operation on the adjacent
rivet in the same chain outer link plate. The
outer plate is then free and the two rivets can
be withdrawn from opposite sides with the
opposite plate in position. Do not use the
removed part again.
When the alterations are finished the chain
should be lubricated as shown in Section AB.
RIVET EXTRACTOR
IN POSITION
RIVET EXTRACTOR
WITH JAWS OPEN
91
Fig. C1l. Chain link rivet extractor, part number 167
C1l
ClassicBike.biz
SECTION D
GEARBOX
DESCRIPTION
REMOVING AND REPLACING THE OUTER COVER ASSEMBLY
DISMANTLING AND REASSEMBLING THE KICKSTART MECHANISM
DISMANTLING AND REASSEMBLING THE GEARCHANGE MECHANISM
INSPECTING THE GEARCHANGE AND KICKSTART COMPONENTS
RENEWING KICKSTART AND GEARCHANGE SPINDLE BUSHES
CLUTCH OPERATING MECHANISM
DISMANTLING THE GEARBOX '"
INSPECTI0N OF THE GEARBOX COMPONENTS
RENEWING MAINSHAFT AND LAYSHAFT BEARINGS
REASSEMBLING THE GEARBOX
CHANGING THE GEARBOX SPROCKET
SPEEDOMETER DRIVE GEAR COMBINATIONS (BEFORE DU.2487S)
GEARBOX SPROCKET AND MAINSHAFT HIGH GEAR
SPEEDOMETER DRIVE GEARS
Section
D1
D2
D3
D4
DS
D6
D7
D8
D9
D10
D11
D12
D13
D14
D1
ClassicBike.biz
><
o
a:I
a:
<I:
w
\:I
c
LOW 3rd
MAINSHAFT ~ ~ E ~
LAYSHAFT
~
~
~ __ ~ A
SPEEDDMETER
DRIVE GEARS
(WHERE FITTED)
---0--
LOW 3rd
2nd HIGH
2nd HIGH
Fig. 01. Plan of Gearbox Components
T13
'" o
ClassicBike.biz
GEARBOX o
DESCRIPTION
The Triumph unit construction twin cylinder
are all with a gearbox
which is an integral part of the right half crankcase.
The gearbox inner and outer covers are made of
aluminium alloy D.T.D. 424 which gives the utmost
rigidity and strength. Gears are manufactured from
high quality nickel steel and subsequently case
hardened and are designed to withstand heavy
loading.
The mainshaft is supported by heavy duty ball races
at each end. and the layshaft by special needle roller
bearings which are pressed into the casing and
inner cover. Keyed to the left end of the gearbox
mainshaft is the multi-plate clutch, which runs in oil
and is operated by a thrust rod which fits through
the centre of the gearbox mainshaft.
The speedometer drive, which is enclosed in the
inner cover is taken from the lays haft by means of
spiral drive gears.
The clutch operating mechanism, kick$carter
quadrant and the gearchange quadrant are all
housed in the gearbox outer cover.
To meet special demands for certain sporting events
there are available alternative close ratio and wide
ratio gears which enables the gearbox to be suitably
converted for road racing and trials riding respec
tively. For details of the parts required for such a
changeover. consult the appropriate TRIUMPH
Replacement Parts Catalogue.
SECTION 01
REMOVING AND REPLACING THE GEARBOX OUTER COVER ASSEMBLY
Slacken the right exhaust pipe finned clip bolt.
silencer clip bolt and remove the exhaust pipe
bracket nut and bolt and drive the R.H. exhaust pipe
free with a hide mallet. Unscrew the right footrest
securing nut and withdraw the footrest. In addition,
on earlier machines with rear panels. remove two
domed nuts, two front panel junction screws and
the top nut securing the right panel. The panel is
then free to be removed.
Slacken off the clutch cable adjustment and slip out
the cable nipple at the handlebar control. Slide the
rubber cover up away from the abutment for the
cable at the gearbox end and unscrew the abutment.
Remove the large slotted plug from the gearbox
outer cover and aCCESS will be gained to the clutch
operating arm. It is only necessary then to release
the cable nipple from the arm with the finger. On
earlier models there is no plug on the outer cover.
To release the cable after slackening at the handle-
bar end it is only necessary to remove the slotted
adaptor. then to unscrew and lift the cable abut-
ment. The slotted nipple seen in Section C1 will
be revealed and the cable nipple detached from this.
Place a drip tray underneath the gearbox and un-
screw the gearbox filler plug and drain plug.
Engage 4th (top) gear. This will allow several other-
wise difficult nuts to be unscrewed by subsequently
applying the rear brake when required.
Unscrew the top and bottom hexagonal nut and the
recess screws from the periphery of the "gearbox
cover. Depress the kickstart lever slightly and tap
the cover until it is free.
o
Drain plug c9;.-- Level plug
Fig. 02. Showing gearbox oil level and oil drain plUBS
When the cover is removed, the gear-change
mechanism. kickstart mechanism and clutch operat-
ing mechanism will be accessible. The gearchange
pedal should be carefully raised then depressed. to
control the release of the plungers and springs from
the gearchange quadrant.
Dl
ClassicBike.biz

ClassicBike.biz

ClassicBike.biz
D
GEARBOX
(5) Check the tips of the plungers and the teeth of
the camplate operating quadrant for chipping
and wear. To remove the camplate quadrant,
first remove the inner cover as shown in
Section D7, then remove the two split pins and
withdraw the spindle.
KICKSTART:
(1) Examine the kickstart quadrant for chipped or
broken teeth or looseness on the spindle and
the kickstart return spring for fatigue cracks
and signs of wear, particularly at the centre
where it engages on the splines of the spindle.
(2) Examine the kickstart spindle bush for wear.
If the required measuring instruments are not
available. use the spindle as a gauge and feel the
amount of play.
(3) Examine the kickstart ratchet mechanism for
wear, giving particular attention to the ratchet
teeth ensuring that they have not become
chipped or rounded. Check that the thin
walled steel bush is a clearance fit in the kick-
start pinion and that the spring is not badly
worn.
(4) Finally. check that the kickst.rt stop peg is
firmly pressed into the inner cover and is not
distorted.
SECTION 05
RENEWING KICKSTART AND GEARCHANGE SPINDLE BUSHES
If it is found necessary to renew the kickstart
spindle bush this should be done by completely
stripping the outer cover of its assembly parts and
heating it to 100'C .. then driving the bush out using
a suitable shouldered drift. Press in the new bush
while the cover is still hot.
Adopt a simil ... r procedure for renewal of the outer
cover gearchange spindle bush. The inner cover
bush does not usually wear much, even after great
mileage has been covered. However, if it is required
to renew the bush, the inner cover should be
removed (Section D7) and the camplate operating
quadrant disconnected.
Using a suitable tap (e.g. :t in. dia. x 10 Whit.) cut
a thread in the bush to a depth of:t in.; heat the
cover to 100C., then reinsert the tap. or, prefer-
ably. a suitable bolt. Grip the bolt (or tap) firmly
in a vice, then drive the cover away using a hide
mallet until the bush is free.
A press or suitably shouldered drift is required to
drive in the new bush, which should be done whilst
the cover is still hot.
SECTION 06
CLUTCH OPERATING MECHANISM
The clutch operating mechanism. which is situated
in the gearbox outer cover, consists of two spring
loaded plates held apart by three balls. which are
seated in conical indentations in the plates.
Wear in this mechanism is negligible, even after
excessive mileage has been covered, so long as the
gearbox oil level is maintained at the recommended
level. The mechanism is removed as a unit by
unscrewing two slotted screws and is then easily
dismantled. The parts are arranged as shown in
D6
Fig. DS. which should be referred to when re-
assembling the mechanism.
Fig. 05. Exploded view of clutch operating mechanism
ClassicBike.biz
GEARBOX D
SECTION 07
DISMANTLING THE GEARBOX
Fig. D6. Gearbox inner cover retaining screws 08
Remove the gearbox Quter cover as shown in
Section D1, leaving the gearbox with 4th (top) gear
selected.
Remove the two short bolts, two long bolts and a
centre nut which serves to retain the rear right
engine mounting plate, then withdraw the plate.
Bend back the tags on the lock washer and unscrew
the kickstart pinion ratchet retainer nut from the
end of the gearbox mainshaft. This should be easily
achieved with 4th (top) gear selected and the rear
brake applied.
On machines prior to D.24875 the speedometer
cable union nut must be undone and the cable
withdrawn from the speedometer drive shaft at the
front of the inner cover.
Remove the Quter pr'lmary cover and dismantle the
transmission as shown in Section C. not forgetting,
finally. to remove the key from the gearbox main-
shaft.
Unscrew the large domed nut from underneath the
gearbox and withdraw the camplate indexing
plunger and spring. The gearbox inner cover is
retained bYr socket screw, a Phillips recessed screw
and a hexagonal bolt (see Fig. D6). When these are
removed the cover can be released by tapping it
outwards with a hide mallet. The gearbox mainshaft
can be withdrawn easily after the selector fork
spindle has been removed. The lays haft and
remaining gears can then be withdrawn. Remove
the camplate and spindle assembly. then remove
the two brass thrust washers which locate over the
needle roller bearings.
The mainshaft high gear, in which the gearbox
mainshaft runs, is locked through the main bearing
and gearbox sprocket. The oil is prevented from
leaving the gearbox through the main bearing by
an oil seal which runs on a ground boss on the gear-
box sprocket. To remove the mainshaft high gear
D7
ClassicBike.biz
D GEARBOX
flp
-\j
20
Fig. 07. Removing the gearbox sprocket nut
with rear brake applied
and renew the oil seal it will be necessary to remove
the sprocket. This can be done by removing the
circular plate from the primary inner cover at the
rear of the clutch, tapping back the bent over portion
of the locking plate and unscrewing the large
hexagonal gearbox sprocket nut (166 in. across
flats). To facilitate removal of the nut, spanner
number Z63 is available.
When the nut is removed, drive the high gear
through into the gearbox using a hammer with a
soft metal drift.
To remove the sprocket. disconnect the rear chain
and remove it from around the sprocket, which can
then be easily withdrawn through the aperture.
Check the oil seal for cracking and wear. If there
has been any signs of excessive oil leakage, renew
it.
SECTION D8
INSPECTION OF THE GEARBOX COMPONENTS
check them for wear and fatigue, as follows:-
(1) Inspect the gearbox housing and inner cover for
signs of cracking and damage to the jOint faces.
Check that the location dowels are in position
correctly in the gearbox and inner cover
(2 dowels each). In preparation for reassembly,
clean the junction surfaces of the gearbox, inner
cover and outer cover of any old deposits of
jointing compound.
(2) Examine both the mainshaft and layshaft for
signs of fatigue, damaged threads and badly
worn splines. Check the extent of wear to the
bearing diameters of both shafts by comparing
them with the figures given in "General Data".
Examine the shafts carefully for signs of seizure.
Excessive friction resistance and seizure will be
indicated by local colouring on the shaft.
(3) Check the layshaft needle roller bearing by
inserting the lays haft and feeling the amount of
play.
08
(4) Inspect the gearbox mainshaft ball bearing races
for roughness due to pitting or indentation of
the ball tracks. An estimate can be made. of
ball wear by feeling the amount of side play of
the centre track. It should not be possible to
detect any movement by hand if the bearing is
in good condition. The mainshaft should be a
hand press fit in the inner cover bearing.
Similarly the mainshaft high gear should be a
good hand press fit in the opposite bearing.
(5) Examine the gears thoroughly, for chipped,
fractured or worn teeth. Check the internal
splines and bushes. Make sure that the splines
are free on their respective shafts with no
tendency to bind, and the bushes in the
mainshaft high gear and lays haft low gear are
not loose or excessively worn. Again, reference
should be made to the dimensions given in
"General Data".
(6) Check that the selector fork rod is not grooved
and that it is a good fit in the gearbox casing
and the inner cover. Inspect the selector fork
running faces for wear. This will only have
occurred if the gearbox is being continually
ClassicBike.biz
GEARBOX D
used with a badly worn mainshaft bearing. The
camplate rollers which fit on the selector fork
are of case hardened steel and consequently
wear should be negligible.
(7) The gear selector cam plate should be inspected
for signs of wear in the roller tracks. Excessive
wear will occur if the mainshaft main bearl'ng
has worn badly. Check the fit of the camplate
spindle in its hOUSing. Examine the camplate
gear wheel for excessive wear. Difficulty will
be encountered in gear selection. causing
su bsequent damage to the gears, if this gear is
badly worn.
(8) Ensure that the campl.te plunger works freely
in the hOUSing and that the moving parts are
free from corrosion. To check if the spring has
become inefficient. measure its length and
compare it with "General Data",
(9) Examine the mainshaft high gear bush for wear
by inserting the mains haft into it and feeling
the amount of play. It is advisable to take
micrometer readings of the mainshaft and
compare them with caliper readings of the bush.
If the clearance is excessively greater than the
figure given in "General Data" the bush should
be renewed as shown in Section 09.
SECTION D9
RENEWING MAINSHAFT AND LAYSHAFT BEARINGS
MAINSHAFT
The mainshaft ball bearings are a press fit into their
respective hOUSings and are retained by spring
circlips to prevent sideways movement due to end
thrust. To remove the right bearing, first lever out
the circlip, then heat the cl..wer to approximately
100'C. and drive out the bearing using a suitably
shouldered drift. The new bearing should be
pressed or drifted in wrilst the cover is still hot
using a suitable tubular drift onto the outer race
(2! in. outside diameter x 6 in. long). Do not
forget to refit the circlip.
To remove the high gear bearing on the left of the
machine. first lever out the large oil seal (which
must be renewed), then remove the retainer
circlip. CarefUlly heat the casing locally to ap-
proximately 100C. then drive out t he bearing from
the inside by means of service tool Z15 or a suitably
shouldered drift. Whilst the casing is still hot. drive
in the new bearing, using a suitable tubular drift
onto the outer race, then refit the circlip and press
in the new oil seal.
MAINSHAFT HIGH GEAR BUSH
If it is reqUired to renew this bush, this can be done
by pressing out the bush using a suitable drift. which
can be made from a 5 in. x i in. diameter piece
of bar by machining a ~ in. dia. x t in. long pilot
at one end. The bush must be pressed out by
inserting the drift at the teeth end of the gear. The
new bush must be pressed in with the oil groove in
the bore of the bush at the teeth end.
Fig. 08. Section through gearbox mains haft oil seal
Finally, ream the bush to size using service tool
reamer Z46. The pressed-in bore size is given in
"General Data".
LAYSHAFT
The right needle roller bearing should be removed
by heating the cover to approximately 100'C. then
pressing or drifting out the bearing using a tool
similar to that shown in Fig. D9 overleaf.
On earlier models with the speedometer driven
from the layshaft. before it is possible to drift out
the bearing it is necessary to remove the slotted
screw which locates the speedometer driven shaft
then to drive out the shaft complete with bush by
means of a soft metal drift.
D9
ClassicBike.biz
o
/
'073/078 ins.
1 YJ 6 ins. DI ~ >....::WI-'-"....:....:o...:>.J
114 ins.DIA.
Fig. 09. Sketch of needle roller and drift
GEARBOX
65
The new bearing should be pressed in, plain end
first, whilst the cover is still hot, from the inside of
thecover, unti!073/078 in. of the bearing protrudes
above the cover face (see Fig. D9).
The left needle roller bearing is of the closed-end
type and is accessible from the left, through the
sprocket cover plate aperture. The casing should
be heated to approximately 100C. and the bearing
driven through into the gearbox using a soft metal
drift. taking care not to damage the bore into which
the bearing fits. The new bearing must be carefully
pressed in whilst the casing is hot, until 073/078 in.
protrudes above the spot face surface inside the
gearbox. Do not use excessive force or the needle
roller outer case may become damaged. resulting in
the rollers seizing. or breaking up.
Finally. the outer portion of the bore into which the
bearing fits, should be sealed with a suitable
proprietary sealant.
SECTION 010
REASSEMBLING THE GEARBOX
Fig. 010. Reassembling the gearbox. Arrow indicates camplate in notch between 2nd and 3rd gear position
D10
ClassicBike.biz
GEARBOX
D
Drive the new oil seal up to the main bearing with
the lip and spring towards the bearing. Press the
high gear into the bearing. Lubricate the ground
tapered boss of the sprocket with oil and slide it
onto the high gear. Screw on the securing nut
finger tight.
Re-mesh the rear chain with the sprockets and
replace the connecting link. Apply the rear brake
and tighten the sprocket securing nut as tight as
possible using service tool Z63. (See Fig. 07.)
Smear the extended nose of the high gear (or on
earlier models smear the bronze bush protruding
from the mainshaft high gear) with oil and replace
the circular cover plate using a new paper gasket.
Lubricate the camplate spindle and offer it into the
spindle housing within the gearbox. Assemble the
camplate plunger and spring into the domed plunger
retaining nut and screw it into position underneath
Place the camplate rollers onto the selector forks
and hold them in position with grease. Position
the selector forks in their respective grooves in
the gears as shown in Fig. 011. (The fork with the
smaller radius is for the mainshaft duster). The
assembly is now ready to be offered into the gearbox
housing. As the mainshaft and layshaft are being
located in their respective bearings, the gears should
be slid into position and aligned so that the selector
fork rollers locate in the roller tracks in the camplate
----
0',
Fig. 011. Reassembling the gearbox components. Arrows indicate camplate rollers in position and
thrust washer corr-ectly located
the gearbox. but do not forget the fibre washer.
Set the camplate with the plunger located to the
notch between second and third gear (see Fig. 010).
Locate the bronze thrust washer over the inner
needle roller bearing. The thrust washer can be
held in position by smearing its rear surface with
grease. Note that the grooved surface ofthe thrust
washer is towards the layshaft. (See Fig. 011).
Lubricate the mainshaft and layshaft captive gears.
then assemble the mainshaft and layshaft gear
clusters as shown in Fig. 011.
and the bores for the selector forks are approxi-
mately aligned. Smear the selector fork spindle
with oil and slide it through the selector forks,
shoulder end first. until it is fully engaged in the
gearbox housing. The mainshaft selector fork will
be noted to be in the innermost position.
Check the camplate operating quadrant is moving
freely in the inner cover and position the bronze
layshaft thrust washer over the needle roller bearing
in the inner cover. Again. use grease to hold the
thrust washer in position during assembly.
011
ClassicBike.biz
o
GEARBOX
--
--
----
--
-
07.
Fig. 012. Refitting the gearbox inner cover
Using a pressure oil can, lubricate all the moving
parts in the gearbox. then apply a fresh coat of
oinUng compound to the gearbox junction surface.
Ensure that the two location dowels are in position
and offer the inner cover assembly to the gearbox.
When the cover is approximately i in. (6 mm.)
away from the gearbox junction face. position the
camplate quadrant in the middle point of its travel
and push the cover fully home. The middle tooth
then aligns with the mainshaft centre line.
Screw in the socket screw, recessed screw and the
bolt. then temporarily assemble the outer cover and
gearchange lever and check that the gearchanging
sequence is correct by simultaneously operating the
gearchange pedal and turning the rear wheel. In the
event of any problem of selection it must be assumed
012
that the quadrant teeth are not engaged accurately
with the camplate pinion. To rectify this. remove
the inner cover again and check that the camplate
has been set as shown in Fig. 010. Offer up the inner
cover again ensuring that the middle tooth is on
the mainshaft centre line. (See Fig. 012.)
When correct gearchanging is established, re-
assemble the kickstart pinion and ratchet, replace
the tab washer and screw on the securing nut to
the torque figure given in "General Data". To
facilitate this. the rear brake should be applied
with fou rth gear selected.
Refit the gearbox outer cover as shown in section
D1 then reassemble the transmission, referring to
section A 2 for the correct quantities and grades of
lubricant for the primary chaincase and gearbox.
ClassicBike.biz
GEARBOX o
SECTION 011
CHANGING THE GEARBOX SPROCKET
To gain access to the gearbox sprocket, first remove
the left footrest and exhaust pipe and then remove
the outer primary cover as shown in Section C3.
Remove the pressure plate. clutch plates and with-
draw the shock absorber unit and clutch sprocket
as shown in Section C9. Remove the key from the
gearbox mainshaft and unscrew the six screws which
serve to retain the circular cover.
Apply the rear brake, then unscrew the gearbox
sprocket securing nut using service tool number
Z63. The rear chain may now be disconnected and
the gearbox sprocket withdrawn through the aper-
tu reo eu rrent models use" Hyd raseal" on the spl i nes
and will need to be removed with extractor Z1S1.
Before fitting the new sprocket check that the
gearbox oil seal is in good condition and that the
rear chain is not excessively worn. Check the
extension as shown in Section A13. If the old chain
is to be retained for further use it should be
thoroughly cleaned in paraffin and lubricated in a
grease bath, lubricate the ground boss with oil, fit a
new locking plate and slide the sprocket over the
gearbox mainshaft and high gear. When the
sprocket is located on the splines screw on the
securing nut finger tight, then re-connect the chain.
With the rear brake applied tighten the nut until it
is as tight as possible and tap over the lockplate.
When replacing the circular cover plate, use a new
paper gasket. Ensure that the oil seal is correctly
engaged over the protruding bronze bush. Re-
assembly then continues as a reversal of the above
instructions. On earlier machines, with the speedo-
meter driven from the layshaft, if it is required to
change the gearbox sprocket for one with a different
number of teeth from that of standard, then it will
also be necessary to change the speedometer drive
gear and driven gear. For further details of this,
see Section D12.
SECTION 012
SPEEDOMETER DRIVE GEAR COMBINATIONS
BEFORE ENGINE NUMBER DU.24875
On earlier machines the speedometer drive is
taken from the right-hand end of the gearbox lay-
shaft. As any overall gear ratio change is achieved by
changing the gearbox sprocket and rear wheel
sprocket, correction has to be made to this speedo-
meter drive ratio, to preserve the correct speedo-
meter drive cable speed.
The chart below gives the part numbers of the
speedometer drive gears required for a change-over
from the standard fitted gearbox sprocket to the
recommended sprocket for use when fitting a
sidecar.
For special purposes it may be necessary to calculate
the speedometer drive gear combination require-
ment. Ifthis is the case, reference should be made to
Technical Information Bulletin No.11 which isavail-
able on request from the TRIUMPH ENGINEERING
CO. LTD .. SERVICE DEPARTMENT.
Model Gearbox
Gears Required:
Cable Var. %
Sprocket Drive Driven R.P. Mile
6T Std. 20 T1744 (10T) T1745 (1ST) 1S90 -06
SICar 18 T1747 (9T) T1748 (1ST) 1600 Zero
TR6 Std. 19 T1744 (10T) T1745 (1ST) 1610 +06
SICar 17 T1747 (9T) T1748 (1ST) 1640 +25
T120 Std. 19 T1744 (10T) T174S (1ST) 1670 +4-2
SICar 17 T1747 (9T) T1748 (1ST) 1695 +5-9
TABLE OF SPEEDOMETER DRIVE GEAR COMBINATIONS
Note: The above chart only applies if the gearbox ratios, the number of teeth on the rear
sprocket and the rear tyre size are as specified in "General Data" for the particular model,
and % variation is calculated on the standard 1600 drive cablerevolutions per mile.
013
ClassicBike.biz
D GEARBOX
SECTION 013
GEARBOX SPROCKET AND MAINSHAFT HIGH GEAR
The splines onthe gearbox sprocket and the main-
shaft high gear were altered on all models from
DU.5825 onwards. The old and new conditions are
not interchangeable, and should either of the items
require replacing ensure that the correct part
number for the particular machine is obtained from
the appropriate Replacement Parts Catalogue.
On current models, the nose of the high gear is
extended to cover the long high gear bush. This
new high gear necessitates a gearbox sprocket
cover plate with a larger centre hole and oil seals.
These parts can only be fitted as a set to earlier
machines from DU.5825 where reqUired.
SECTION 014
SPEEDOMETER DRIVE GEARS
From engine number OU.24875 the speedometer
drive gears were deleted, as the speedometer
drive is now taken from the rear wheel. This avoids
014
having to change the drive gears when altering the
gearbox final drive sprocket to vary the overall
gear ratio.
ClassicBike.biz
SECTION E
FRAME AND ATTACHMENT DETAILS
REMOVING AND REFITTING THE FUEL TANK
REMOVING AND REPLACING THE REAR PANELS (6T)
REMOVING AND REPLACING THE SWITCH PANEL (TR6 AND T120) ...
REMOVING AND REPLACING THE OIL TANK
REMOVING AND REPLACING THE BATTERY CARRIER ASSEMBLY
REMOVING AND REPLACING THE REAR MUDGUARD
ADJUSTING THE REAR SUSPENSION ...
REMOVING AND REFITTING THE REAR SUSPENSION UNITS
STRIPPING AND REASSEMBLING THE SUSPENSION UNITS
REMOVING AND REFITTING THE SWINGING FORK
RENEWING THE SWINGING FORK BUSHES ...
REMOVING AND REPLACING THE REAR FRAME
FRAME ALIGNMENT ...
FAIRING ATTACHMENT LUGS AND STEERING LOCK
FITTING REPLACEMENT SEAT COVERS
REPAIRS
PAINTWORK REFINISHING
Section
E1
E2
E3
E4
E5
E6
E7
E8
E9
E10
E11
E12
E13
EH
E15
E16
E17
E1
ClassicBike.biz
E
E2
FRAME
VERY IMPORTANT
PLEASE NOTE THAT U.N.F. (UNIFIED)
THREADS ARE BEING INTRODUCED
PROGRESSIVELY THROUGH THE
FRAME GROUP. IT IS MOST IMPORT
ANT WHEN REPLACING NUTS, BOLTS
AND THREADED PARTS THAT THE
THREAD IS RECHECKED.
'78
Fig. E1. General arrangement of front and rear frame assembly
ClassicBike.biz
FRAME E
SECTION EI
REMOVING AND REPLACING THE FUEL TANK
Turn both fuel taps to the "off" position then
unscrew the union and disconnect the feed pipes
at the taps. Raise the twinseat then unscrew the
rear fuel tank securing bolt.
U.S.A. UP TO DU.66244
U.K. AND GENERAL EXPORT UP TO DU.77670
Detach the locking wire from the front tank bolts
and unscrew them. The tank is then free to be
removed. On earlier machines fitted with the
nacelle type head lamp unit the tank may foul the
underside of the nacelle cover, in this case the two
two rear nacelle securing screws should be removed
to give sufficient clearance.
Replacing the tank is the reversal of the above
instructions, but do not forget to tit the mounting
ru bbers on the front and rear tan k secu ri ng bolts.
Do not over-tighten the feed pipe union nuts as this
may result in failure of this part with subsequent
fuel leakage. Finally, rethread the locking wire
through the heads of the two front securing bolts
to prevent them unscrewing.
U.S.A. FROM DU.66245
Fig. E2. Front reflectors (U.S.A.)
Reflectors are fitted-below the front of the gas tank,
secured by the front tank mounting bolts. (See
Fig. E2).
To remove the petrol tank securing bolts, the
locking wire must be removed. The easiest method
is by cutting it with a pair of wire cutters. A bbx
or "T" spanner can be used to unScrew the bolts,
or alternatively the reflector lens may be removed
to allow access with an open-ended spanner. The
chrome plated rim should first be removed by
pulling off a locating groove in the plastic retainer.
Gently prise the reflector lens away from its retainer
by inserting a blunt screwdriver between the lens
and the plastic lip. Remove the retainer by again
easing a blunt screwdriver between the plastic and
the steel lip ofthe bracket.
Proceed then as for previous machines. Refit the
reflectors in a similar manner.
ALL MARKETS FROM DU.n670
The petrol tank is secured at the two front mounting
points by studs and "Cleveloc" (self locking) nuts.
No locking wire is required on this arrangement.
Dismantling and reassembly procedure is as
described above.
SECTION El
REMOVING AND REPLACING THE PANELS (6T)
EARLIER 6T ONLY
Removal of the left and right rear enclosure panels is
achieved by unscrewing two domed nuts, a plain
nut (just below the rear of the fuel tank) from
each panel and two front panel junction screws.
The panels are then free to be removed.
When replacing them, it is important that the
distance pieces which fit over each of the engine
mounting plate centre studs are in position other-
wise the panel will become distorted when the
domed nuts are tightened.
E3
ClassicBike.biz
E FRAME
SECTION E3
REMOVING AND REPLACING THE SWITCH PANEL
To remove the current side panel which also serves
as the tool compartment, merely unscrew the
plastic knob at the top left-hand corner of the panel
and pull the panel with rubbers forwards and
outwards off the two securing pins on the rear
sub frame. On reassembly ensure that the plastic
washer is fitted to the securing screw.
Remove the rear chain oil feed pipe from the oil
tank neck and pull it through the rubber grommet
in the switch panel. Disconnect the wires from the
stop lamp switch after removing the battery
retaining strap and battery from the machine.
(NOTE: The brake lamp switch wires are fitted
with snap connectors and are a push fit into the
switch. Pull the wires horizontally to remove).
Carefully thread the wires through the rubber
grommet in the switch panel.
Remove the two nuts and washers securing the
top panel mounting brackets to the battery carrier
and the nut retaining the bottom mounting bracket
Fig. E3. Switch panel fixing arrangement
(earlier models)
to the rear engine plate. Pull the bracket away
from the engine plate and down from the rubber
bush in the switch panel. The front bracket of
the panel can then be released from the frame by
unfastening the nut and bolt At this stage it is
necessary to remove lighting switch harness socket,
pulling the socket away from the switch body.
Disconnect the three Lucar connectors from the
ignition switch and lift the panel clear.
Fig. E4. Switch panel lower fixing bracket
(earlier models)
The switch panel on earlier models is secured by a
three point fixing. Removal is the same as on
later types except that the bottom bracket is
welded to the panel. On these earlier machines
the switches should be removed by unscrewing
the centre recessed screw, Withdrawing the knob,
and unscrewing the switch retaining nut. The
rubber cover should be prised off the ignition
switch before the central nut is unscrewed.
The replacement of the panel is the reversal of the
above instructions.
When replacing the panel. ensure that the sockets
are fully engaged. The pins in the sockets are so
arranged that they cannot be re-connected wrongly.
On models where the lower fixing pillar is fitted
check that the mating rubber grommet is correctly
replaced in the panel (see Fig. E4).
SECTION E4
REMOVING AND REPLACING THE OIL TANK
Remove the oil tank drain plug and filler cap and
drain the oil into a suitable container. (On machines
E4
with rear decorative panels. first ren-,ove the right
panel). If a tool tray is fitted, remove it at this stage
ClassicBike.biz
FRAME E
by taking out two nuts and bolts. Disconnect the
engine oil feed pipe securing clip. unscrew the
return pipe union nut and oil tank filter. Remove
the oil pipe feeding the rear chain located on the
oil tank filler neck and disconnect the rocker feed
pipe below the tank. Remove the battery carrier
as described in Section ES. Remove the bolt holding
the bottom bracket to the frame and remove the
bracket completely from the oil tank bottom
grommet. Take off the nuts from the oil tank
mounting pegs in the rubbers, preventing the pegs
from turning with a screwdriver if necessary. This
will release the red earth (ground) leads at the
front one and twin seat check strap at the rear one.
Push the slotted pegs back through the rubber
sleeves noting that the front peg has a spring washer.
Lift the oil tank and push the top inwards to enable
the froth tower to clear the frame brackets. Lastly,
pull the lower part of the tank outwards and drop
the tank clear of the frame.
Unscrew the large hexagon-headed oil tank filter
body from beneath the oil tank and thoroughly
clean it in paraffin (kerosene). On earlier machines
unscrew the bottom mounting bolt and remove the
oil tank. This is bese achieved by allowing the
bottom bracket to be lowered into the space
behind the gearbox, then tilting the top of the
oil t.ank outwards so that it can be lifted clear.
After removal, clean very thoroughly both the oil
tank filter and oil tank in paraffin (kerosene).
Reassembly is the reversal of the above instructions
but remember to fit the bottom mounting rubber
and also to connect the seat check wire to the
rear top mounting bolt. When connecting the oil
feed pipe union nut take care to avoid over-
tightening as this may result in failure of the union
nut. When connecting the oil lines ensure that
chafing of the rubber connections does not occur.
Failure to observe this may result in rubber frag-
ments entering the oil system and subsequently
causing blockage. The clips should be tightened
carefully. If oil leakage is experienced from one of
these junctions on earlier models, it is advisable
to purchase and fit new clips. Refit the oil filler cap
after add i ng the req ui red quantity.
Fi,. ES. Showin, two 6 volt batteries in position in the battery carrier (earlier condition) E5
ClassicBike.biz
E
FRAME
SECTION ES
REMOVING AND REPLACING THE BATTERY CARRIER
Lift the twinseat, disconnect the negative (-) and
positive (+) battery leads. Release the battery
retaining rubber strap by easing the front buckle
off the carrier front sleeve nut. lift the battery
complete with breather pipe clear of the machine.
Note for refitting that the breather pipe is intended
to pass down under the machine, rearward of the
swinging arm lug. Remove the nut holding the
earth lead and rectifier to the battery carrier.
Slacken the single nuts on both the front and rear
cross straps and the carrier can then be lifted clear.
(If the carrier pressing is very tight on the cross
straps it may require some effort to lift it clear).
The cross straps can be removed at this stage if
required by removing the nuts and bolts at the
right side and sliding the straps complete with
rubbers off the frame pegs.
On earlier models remove the battery retainer and
bolts, lift the battery clear and the carrier can then
be lifted sufficiently to unfasten the bolts securing
the heat sink for the Zener Diode. The carrier can
then be removed.
If it is desired to remove the rubber mounted
battery carrier cross members, this is achieved
merely by removing the nuts and bolts at the right
hand end and disengaging the cross members at the
other end.
Refitting is a reversal of the foregoing. This
procedure applies for the single 12 volt battery, for
two 6 volt batteries in series and the single 6 volt
condition.
Fig. E6. Oil tank mounting bolt assembly. (t2 volt single battery)
E6
ClassicBike.biz
FRAME E
SECTION E6
REMOVING AND REPLACING THE REAR MUDGUARD
Remove the split link and disconnect the rear chain
from the rear wheel sprocket. Unscrew the rear
brake rod adjuster nut and remove the nut securing
the torque stay to the anchor plate. Unscrew the
wheel spindle nuts and withdraw the wheel.
Slacken the rear number plate securing bolts and
bottom nut, together with the bottom breather
pipe clip on current models. Remove the two bolts
securing the top dip and reinforcing strip below the
mudguard. Disconnect the rear light at the two
snap connectors (behind the number plate on late
models or by the battery on earlier ones). Remove
the number plate complete with tail lamp. On
early 6T models remove the left and right valances
and panels. Remove the nut, bolt and large plain
washer securing the front of the mudguard to the
pivot lug bracket.
Remove the two bolts securing the mudguard to the
bridge, noting that the large washer fits below the
mUdguard and the small washer (and breather pipe
clip on left side) on top.
Remove the last bolt holding the wiring protector
in situ. On current models. for convenience
disconnect the tail lamp lead at the double snap
connector by the mudguard top bridge. Lower the
mudguard. taking care not to scratch this on the
lifting handle. Replacement is a reversal of the
above instructions but ensure that the electrical
connections are coupled correctly and when re-
connecting the rear chin. check that the nose of the
spring connection link is facing in the direction or
rotation.
SECTION E7
ADJUSTING THE REAR SUSPENSION
The movement is controlled by Girllng combined
coil spring and hydraulic damper units. The
hydraulic damping mechanism is completely sealed
but the static loading of the spring is adjustable.
There is a three position cam ring below the
chromium plated dust cover and a "e" spanner is
prOVided in the toolkit. To increase the s"atic
loading ofthe spring place the machine on the stand
so that there is least load on the spring and use the
"c" spanner to turn the cam; both units must be
on the same notch whichever may be chosen.
The table opposite shows the spring rates and
colour codes for the purposes deSignated.
Standard
T120, TR6
Earlier 6T
T120n
T120R
TR6C
TR6R
Rate
Ib./in.
145
100
Fitted
Length Colour
(ins.) Code
Blue/
80 Yellow
Green/
84 Green
E7
ClassicBike.biz
E FRAME
The standard lowest position is for solo riding, the
second position is for heavier solo riders or when
luggage is carried on the rear of the machine and the
third or highest position is for use when a pillion
passenger is being carried.
o
72
FIRST POSITION
LIGHT LOAD
SECOND POSITION
MEDIUM LOAD
THIRD POSITION
HEAVY LOAD
Fig. E7. Adjusting the rear luspension units
SECTION E8
REMOVING AND REFITTING THE REAR SUSPENSION UNITS
Re""!oval of the suspension units is achieved by
removing the top and bottom fixing bolts whilst
the machine is sUitably mounted so that the rear
wheel is off the ground.
The top suspension fixing bolts are fitted with their
heads towards the outside of the machine so that it
is possible to remove the suspension units without
dismantling the rear mudguard assembly etc. These
bolts also serve to retain the lifting handles. The
lower fixing bolts can also be removed without
disturbing the chainguard.
E8
On earlier 6T machines with panels the top fixing
bolts are fitted from the inside and the rear wheel
and mudguard require removing so that the pivot
bolts can be withdrawn and the suspension units
removed.
When refitting the units, ensure that the bridge
bracket fits in-between the lifting handle and the
frame prior to inserting the pivot bolts. It may
be necessary to use an alignment bar to assist in
bringing the holes into line.
ClassicBike.biz
FRAME E
6-----------------------------
4 ~
'-------2
5------/
1. Hydraulic damper unit
2. Rubber bump stop
~
l. Coiled spring
4. Outer shield
5. Inner shield
6. Spring retainers
7
7. Bonded bush 7J
Fie. E8. Exploded view of the rear suspension unit
E9
ClassicBike.biz
E FRAME
SECTION E9
STRIPPING AND REASSEMBLING THE SUSPENSION UNITS
The suspension unit consists of a sealed hydraulic
damper lin it, outer coiled spring and dirt shields.
The static loading on the spring is adjustable and
should be set according to the type of conditions
under which the machine is to be used (see
Section E7).
To dismantle the suspension unit and remove the
spring, it is required to compress the spring whilst
the two semi-circular spring retainer plates are
removed. To do this first turn the cam until it is
in the "LIGHT-LOAD" position, then carefully
grip the bottom lug in a vice. Take firm hold of
the outer dirt shield and pull it until the spring is
sufficiently compressed to allow the spring retainers
to be removed.
The damper unit should be checked for leakage,
bending of the plunger rod and dampin'5 action.
Check the bonded pivot bushes for wear and ensure
that the sleeve is not loose in the rubber bush.
The bushes can be easily renewed by driving out the
old one and pressing in the new one using a smear
of soapy water to assist assembly.
Squeaking coming from a suspension unit will
probably be due to the spring rubbing on the
bottom shield. To overcome this, smear some
high-melting point grease on the inside of the
snield. Under no circumstances should the plunger
rod be lubricated.
Note.-For information concerning suspension
units or spare parts, the local Girling agent should
be consulted.
Reassembly is a reversal of dismantling. Check that
the cam is in the light load position before com-
pressing the spring.
SECTION EIO
REMOVING AND REFITTING THE SWINGING FORK
Disconnect the chain and remove the front anchor
stay securing bolt, then unscrew the brake operating
rod adjuster nut. Slacken the wheel spindle nuts
and withdraw the rear wheel.
On earlier machines where rear enclosure panels
are fitted these must be removed. To do this un-
screw two domed nuts, two front panel junction
screws and a nut just below the rear of the petrol
tank. The panels are then free to be removed.
R.emove two long and two short bolts which serve
to retain each of the left and right rear engine
mounting plates and withdraw the plates. There
is also a nut fitted centrally to the plates except on
earlier models with rear enclosure panels.
Slacken off the rear chainguard bolt and remove the
front chainguard securing bolt. Disconnect the
leads from the stop lamp switch and remove the
chainguard.
E10
R.emove the two bolts which secure the suspension
units to the swinging fork.
On machines where the swinging fork pivot spindle
nut is on the right of the machine the oil scavenge
pipe should be disconnected from the oil tank to
give spanner clearance for removing the pivot
spindle. On earlier' models the spindle was fitted
from the left of the machine. To remove the
spindle, first unscrew the locking nut, then un-
screw the spindle until It is free to be withdrawn.
The swinging fork can then be removed and the end
plates, outer sleeves and distance tube withdrawn.
Note that some earlier swinging arm bolts have
brazed-on heads. On later machines a 'one-piece'
bolt S620 is used and this could be fitted to advantage
in direct replacement of earlier bolts, since the
2 T.P.1. thread difference will be advantageous in a
'worn frame' condition.
1964 _ 5
ClassicBike.biz
FRAME
E
Fig. E9. Exploded view of swinging fork assembly
(kerosene) and inspected for wear giving particular
attention to the fit of the two outer sleeves in the
swinging fork bushes. The working clearance
between sleeve and bush should not be excessive.
If excessive wear is in evidence, the bushes will
require renewing, for details ofthis see Section E11.
The parts should be reassembled in the order shown
in Fig. E9 with the addition of a sufficient quantity
of the recommended grade of grease to fill the
space surrounding the distance tube. Also, the
sleeves and bushes should be well greased. The
'0' rings should be inserted into the lipped end
plates and pushed over the ends of the swinging fork
cross tube whilst the swinging fork is offered to the
pivot lug and the swinging arm bolt inserted. The
bolt should be tightened till the fork can just be
moved upwards and downwards with little effort.
The lock nut and tab washer should then be fitted
and the nut tightened. Reassembly then continues
as the reversal ofthe above instructions. To remove
side play where the bushes are sound it is necessary
only to take out the distance sleeve and file one end
to reduce the overall length. A thicker end plate
F7675 is available to maintain the correct distance
between the frame lugs. only on earlier models.
Should the swinging arm bolt be renewed. ensure
the thread is the same in the frame and on the bolt.
Fig. E10. Swinging fork lubrication nipple
E11
ClassicBike.biz
E
FRAME
SECTION Ell
RENEWING THE SWINGING FORK BUSHES
If the swinging fork bushes require renewing they
should be removed by means of a sUitable soft
metal drift inserted in the tubular housing at an
angle and located onto the far side bush. By
dexterous use of a hammer and a drift moving It
round the edge of the bush a little at a time the bush
should be easily removed with no resultant damage
to the bore of the housing (see Fig. E11).
New bushes are of the steel backed pre-sized type
and when carefully pressed in, using a smear of
grease to assist assembly, they will give the correct
diametral working clearance. If a press is not avail-
able the bush can be fitted by using a suitably
turned drift and hammer. Ensure that the bush
enters squarely and that no burr is set up due to
misalignment. Bore sizes and working clearances
are given in "General Data".
Fig. E11. Removing a swinging fork bearing bush
SECTION EI2
REMOVING AND REPLACING THE 'REAR FRAME
and remove the battery. Unscrew the four bolts
which serve to secure the twinseat hinges. then
disconnect the check wire and remove the twinseat.
Remove the side or switch panel (TR6 and T120) or
panels 6T, oil tank, and rear mudguard as described
in Section E2 to E6 inclusive.
Slacken the finned clip bolts, silencer clip bolts and
two nuts which serve to secure the exhaust pipes
underneath the engine. then remove the exhaust
pipes by tapping them in a forward direction with
a hide or rubber mallet. Remove the left and right
silencers, then remove two short bolts, two long
bolts and a central nut which serve to retain
eachofthe left and right rear engine mounting plates.
Remove the plates complete with footrests.
E12
On earlier models where the footrests are secured
underneath the engine they should be removed by
slackening their securing bolts and giving each
footrest a sharp tap in a downward direction to
release it from its locking taper.
Remove all frame clips which connect the wiring
harness to the rear frame portion and unscrew the
bottom left and right bolts which serve to secure
the rear frame to the front frame. then remove
the top securing stud. The rear frame is now free
to be removed, this is best achieved by lifting It
vertically upwards over the swinging fork.
Replacement is the reversal of the above instruc-
tions, but refer to the relevant Wiring diagram in
Section H17 when reconnecting the electrical units
and wiring harness.
ClassicBike.biz
FRAME E
SECTION EI3
FRAME ALIGNMENT
A
SLIDING FIT
ON BAR
WELDED
HOLE TO GIVE
IN POSITION

2.091.DI
GOOD SLIDING FIT
209u"
I
PART A.- MILD STEEL - 2 OFF
PART B.- MILD STEEL BAR
l1in. DIAMETER MAXX2ft.LONGI
Fig. E12. Sketch of frame checking fixture
If the machine has been damaged in an accident the
frame portions must be checked for correct align-
ment. In the following paragraph details are given
of alignment checking for all parts of the frame
(excepting the telescopic fork which is dealt with
in Section G).
Basic requirements for alignment checking are a
engineer's checking table (surface area approxi-
mately 3 feet X 5 feet), adjustable height gauge
(Vernier type preferable) two suitable "V" blocks,
several adjustable height pillars, a set-square and
a suitable jig as shown in the sketch (Fig. E12).
FRONT FRAME
It Is essential that after setting, or checking the
front frame lug centre line is in a plane perpendi-
cular to the plane of the swinging fork pivot lug
centre line. It is also essential, that the remaining
tubes and lugs are in their relative positions within
the stated limits of accuracy.
The method of checking the front frame is that of
securely fitting an adaptor spindle of the type shown
in Fig. E12 to the head lug. It is then required to
support the spindle and head lug on a plane parallel
to, and approx. 6 ins. (15 cm.) from, the checking
table surface. For this purpose two "V" blocks,
packing pieces and two suitable "G" clamps will
ON BAR
3
n
~
I n
;...---- 2"4---";
DIA.
7S
be required. At the other end of the frame (swing-
ing fork and rear frame removed) an adjustable
pillar should be placed under the down tube adj.-
cent to the swinging fork pivot lug (see Fig. E13).
The height of the pillar can be determined by
measuring the diameter of the tube which is to
rest on it, halving the diameter and then sub-
tracting it from the dimension between the head
lug centre line and table surface.
The frame centre line should now lie parallel to the
checking table surface if the frame alignment is
COrrect.
To verify this take height readings on the front
down tube, top tube and rear down tube. See
Figs. E13 and E14. Permissible maximum variation
is n in. (075 mm.).
Fit the swinging fork pivot spindle with the two
outer sleeves and distance tube attached and check
the pivot lug for squareness using a set square at
the two location points as shown in Figs. E13 and
F14.
Then. using a set square. check that the bottom
tubes are aligned by bringing the set square to
bear on them at the front and rear.
Using a steel rule or SUitable instrument measure
the hole centres and compare the figures obtained
with those given in Figs. E15 and E16.
E13
ClassicBike.biz
E
FRAME
Fig. En. Checking the front frame alignment
Fig. E14. Checking the front frame alignment
E14
ClassicBike.biz
FRAME E
o
o
77.
Fig, E15. Basic dimensions of the frame assembly
REAR FRAME FRAME ASSEMBLY
The rear frame basically serves to mount the rear
suspension units and twinseat etc . and it is only
alignment between the top suspension unit support
brackets with those on the swinging fork that is of
most importance. The best mea.ns of checking rear
frame alignment is that of fitting it to the front
frarr.e and taking readings as indicated in the
following paragraph.
Securely bolt the rear frame to the front frame and
fit the swinging fork so that it can just be rotated
by slight hand pressure. Mount the complete
assembly horizontally on the checking table as
described above. then take height readings at the
swinging fork ends and top and bottom suspension
unit mounting brackets. referring to Figs. E15 and
E16 for dimensions. These brackets should not
E15
ClassicBike.biz
E
FRAME
_____________ . ____________
,.
151'"6
19 44"
______ -t ___ __ __
Fig. E16. Basic dimensions of earlier frame assembly (before engine number DU.14875)
Before engine number DU.24875 the basic frame
measurements were different. See Fig. E16. Where
an earlier machine requires a replacement front
frame for any reason, e.g. accident, the later frame
E16
will be supplied. This front section is directly inter
changeable with the earlier frames, and no additional
parts will be required to fit it.
ClassicBike.biz
FRAME
E
79
Fig. E17. Checking the swinging fork
be more than +.- in. (15 mm.), out of line otherwise then be taken at both ends of the wheel spindle to
the suspension units will be working under excessive establish any mis-alignment. (Fig. E17).
stress. Next, check that the distance between the fork
If, when frame alignment is completed, the amount ends is as given in "General Data",
of discrepancy is excessive and rectification is It is now necessary to lever the fork ends in the
needed, then it is advisable to return the damaged correcting direction until the wheel spindle can be
part to the Service Department of Triumph inserted and found to be parallel with the pivot bush
Engineering Company. However, in the case of the centre line. To do this, a bar of 4ft. length by 1 ins.
swinging fork where the misalignment is not more diameter is required. It is now that great care is
than tin. (6 mm.), measured at the tips of the fork required. Insert the bar at the end of the swinging
ends, it may be possible to rectify this by the fork adjacent to the suspension unit mounting
following means. brackets so that it is over the "high" fork leg
SWINGING FORK and under the "low" fork leg. Exert gentle pres-
It is required to check that the centre line of the sure at the end of the bar then insert the spindle
pivot spindle is in the same plane as the centre line and the alignment. Repeat this procedure
ofthe rear spindle. To do this, first place a tube or using increased loads until the spindle height
bar of suitable diameter into the swinging fork readings shows that the swinging arm is now
bearing bushes, then mount the swinging fork on aligned in the opposite sense. A small leverage
two "Y" blocks, one either side, and clamp it now applied from the other side will bring the
lightly to the edge of the checking table. Fit the wheel back to parallel.
rear wheel spindle into the fork end slots or, Note: Apply the leverage bar as near as possible
alternatively, use a straight bar of similar diameter, to the suspension unit brackets, otherwise the
then support a fork end so that the swinging fork tubes may become damaged. DO NOT USE THE
Is approximately horizontal. Height readings should FORK ENDS.
E17
ClassicBike.biz
E
FRAME
SECTION EI4
FAIRING ATTACHMENT LUGS AND STEERING LOCK
From engine number DU.24875 fairing attachment
lugs are incorporated in the steering head assembly
to simplify the fitting of fairings. These are shown
in Figs. E1 and E18.
Fig. E18. Fairing attachment lugs
An extension of the steering head lug accommodates
the peg of the steering lock fitted to the fork crown.
See Fig. E19.
Fig. E19. Steering lock
SECTION EIS
FITTING REPLACEMENT SEAT COVERS
'Quiltop' twinseats have a cover retained by sprags
which are part of the seat pan.
When fitting a replacement seat cover it is very
important to first soak the complete cover
assembly in hot water in order to soften the plastic
so that it can easily be stretched into place. After
soaking the cover in hot water. wring out the
E18
excess water and you will find that the cover can
very easily be stretched into place to give a neat
fit without any wrinkles. This job is very difficult
if you do not follow this suggested method.
Ideally the seat should be allowed to dry out in a
warm place before being put back into service.
ClassicBike.biz
FRAME E
SECTION EI6
REPAIRS
Repairs covered in this section are simple operations
requiring only a minimum of special tools. The type
of repairs pOSSible with these tools are those such
as small dents to mudguards. panels etc . caused by
flying stones or slight grooves which have not
affected a large area or torn the metal. The tools
required are shown below in Fig. E20.
80
Fig. DO. Tools used for panel repairs
REMOVAL OF DENTS
To remove small dents a spoon and suitably shaped
dolly block are reqUired. A suitable spoon can be
made from a file by removing the teeth and polishing
the surface then cranking it as shown in Fig. E20.
Place the dolly block underneath the panel then
hammer the dent(s) carefully with the spoon until
something like the original contour is achieved.
Lightly file the surface to show any high spots
there may be and 'Jse the dolly and spoon to remove
them.
Note.-Do not file more than is necessary to show
up the high spots. Care should be taken to keep
filing to a minimum otherwise serious thinning
of the metal will occur.
Where denting has occured without resultant
damage to the paint-work the dent(s) may be
removed whilst the paintwork is preserved by
careful use of a polished spoon and dolly block.
Dents which are comparatively larger may be
removed whilst the paintwork is preserved by
placing a "sandbag" against the outer surface and
hammering the inside of the panel with a suitably
shaped wooden mallet. A "sand bag" can be made
from a piece of 18 in. square leather by folding it
and packing it tightly with sand. Finally. finish off
using a suitable dolly block and polished spoon as
reqUired.
101
Fig. E2i. Removing a dent with dolly block and spoon
Note.-It is not advisable to use a hammer as
hammer-blows tend to stretch the surrounding
metal. giving rise to further complications. Also.
unless the aim is true, damage of a more serious
nature may result.
Where a fuel tank has become damaged the repair
work should only be entrusted to a competent
panel beater. or preferably. return the tank to the
Service Department-Triumph Engineering Com-
pany Ltd.
E19
ClassicBike.biz
E FRAME
SECTION EI7
PAINTWORK REFINISHING
PAINT STRIPPING
Except in cases where a "touch-up" is to be
attempted. it is strongly recommended that the
old finish is completely stripped and the refinish
is carried OUt from the bare metal. A sUitable
paint stripper can be obtained from most paint
stores and accessory dealers.
The stripper should be applied with a brush and
allowed approximately 10 minutes to react. A
suitable scraper should be used to remove the old
finish, then the surface cleaned with water using
a piece of wire wool. Ensure that all traces of paint
stripper are removed. If possible, blowout crevices
with compressed air.
It is advisable to stri p a small area at a ti me to avoid
the stri pper d ryi ng and also to enable easier
neutralizing of the stripper.
Finally. the surface should be rubbed with a grade
270 or 280 emery cloth to give a satisfactory finish
then washed off with white spirits or a sUitable
cleaner solvent.
PRIMING
A thin coat of cellulose primer must be sprayed
onto the surface prior to application of an under-
coat or stopper. Undercoat and stopper will not
adhere satisfactorily to bare metal. It is advisable
tothin the primer by adding 1 part cellulose thinners
to 1 part primer. Ensure that the primer is dry
before advancing further.
APPLYING STOPPER
Imperfections and slight dents in the surface may
be filled with stopper. but rubbing down with
"wet and dry" should not be attempted until
the undercoat or surfacer has been applied.
Apply the stopper with a glaZing knife in thin layers.
allOWing approximately 20 minutes for drying
between each layer. After the last layer. allow
the stopper about 6 hours (or over-night if pOSSible)
to dry. Heavy layers or insufficient drying time will
result in risk of surface cracking.
E20
UNDERCOAT (SURFACER)
Most cellulose undercoats also called surfacers, will
suffice for a base for TRIUMPH finishes. About two
or three coats are reqUired and should be sprayed
on in a thinned condition using 1 part cellulose
thinners to 1 part undercoat. Allow approximately
20 minutes between each coat.
If stopper has been applied the final layer of under-
coat should be sprayed on after smoothing the
surface with "wet and dry" abrasive as shown
below.
WET AND DRY SANDING
After application of the undercoat. the surface
should be rubbed down with 270 or 280 grade
abrasive paper used wet. An ideal method Is to
have a rubber block approximately 3in. x2ln. x1 In.
around which to wrap the emery paper. However.
this is only recommendable for flat surfaces; where
rapid change of sections occur. a thin felt pad Is
more useful.
The abrasive paper should be allowed to soak in
cold water for at least 15 minutes before use. A
useful tip is to smear the abrasive surface of the
paper with soap prior to rubbing down. This
will prevent clogging and should at least treble
the useful life of the paper if it is washed thoroughly
after each rub-down.
When the surface is smooth enough. wash It thor-
oughly with water and dry off with a clean sponge-
If smoother surface than this is required It can be
given another layer of undercoat and then the
rubbing down procedure repeated using 320 or
400 grade of paper depending upon conditions.
FINISHING
Before spraying on the finishing coats the surface
must be quite smooth, dry and clean. It is important
that conditions are right when finish spraying is
to be carried out otherwise complications may
occur. Best conditions for outdoor spraying are
those on a dry sunny day without wind. Moisture
in the atmosphere is detrimental to paint spraying.
ClassicBike.biz
FRAME E
The first coat should be thinned in the ratio of
50% cellulose thinners to 50% lacquer. Subsequent
coats should have a higher proportion of thinners
as shown below.
Allow at least 10 minutes between each coat and
after the final coat leave overnight or H hours if
possible. For most purposes the 2nd coat offinishing
is more than adequate.
Cellulose
Thinners
1st Coat 50%
2nd Coat 60%
3rd Coat 70%
4th Coat 80%
Lacquer
50%
40%
30%
20%
POLISHING
The final colour coat must be completelY dry
before cutting and polishing. Using a clean rag
rub down with brass polish or fine cutting paste
and burnish to a high gloss using a clean mop before
applying a suitable wax polish for protection and
shine.
Between each coat the surface may be flatted by
hand with 320 or 400 abrasive paper as required.
Note.-TRIUMPH supply only the finishing
lacquers. These are available in * pint tins and
aerosol sprays or, for workshop use, 1 gallon tins.
FLAMBOYANT FINISHES
To regain the original depth of colour or shade, when
applying flamboyant finishes, they must be applied onto
the correct base colou r e.g.
Finish (Ser. Ref.) Base Colour (Ser. Ref.)
Kingfisher blue K Silver V
Hi-Fi red HF Gold G
Regal purple P Silver V
Burnished gold BG Gold G
Pacific bl ue PB Silver V
Flame F Gold G
Burgundy B Gold G
METALLIC FINISHES
Metallic finishes can be applied equally as well to either a
white or brown primer, and no base colour is needed.
These finishes are as follows:-
Finish
Riviera blue
Mist Green
(Ser. Ref.)
RB
MG
E21
ClassicBike.biz
SECTION F
DESCRIPTION
REMOVING AND REFITTING THE FRONT WHEEL
REMOVING AND REFITTING THE REAR WHEEL
REMOVING AND REFITTING THE QUICKLY DETACHABLE (Q.D.) REAR WHEEL
FRONT AND REAR WHEEL ALIGNMENT
BRAKE ADJUSTMENTS
STRIPPING AND REASSEMBLING THE BRAKES
RENEWING BRAKE LININGS
REMOVING AND REFITTING THE WHEEL BEARINGS
WHEEL BUILDING ...
WHEEL BALANCING
REMOVING AND REPAIRING TYRES
SECURITY BOLTS
TYRE MAINTENANCE
SIDECAR ALIGNMENT
Section
Fl
F2
F3
F4
FS
F6
F7
F8
F9
FlO
F'1l
F12
F13
FH
Fl
ClassicBike.biz
F WHEELS, BRAKES AND TYRES
SECTION FI
REMOVING AND REFITTING THE FRONT WHEEL
Place the machine with the front wheel approxi-
mately six inches off the ground. First. unscrew
the handlebar front brake adjuster then disconnect
the cable at the actuating lever on the brake plate
by removing the spring pin on current models or
the split pin, washer, and pivot pin on earlier
models. On twin leading shoe brakes. to release
the cable from the anchor plate it is necessary to
remove the split pin at the cable abutment. Un-
screw the two wheel spindle cap bolts from the
base of each fork leg and remove the wheel.
Refitting the wheel is the reversal of the above
instructions but care should be taken to ensure
that the anchor plate locates correctly over the
peg on the inside of the right fork leg. Tighten the
spindle cap bolts evenly a turn at a time. On twin
leading shoe brakes the cable retaining split pin
should be replaced.
SECTION F2
REMOVING AND REFITTING THE REAR WHEEL
First unscrew the rear brake adjuster, then dis-
connect the rear chain. Slacken the bolt at the rear
of the chainguard so that the chainguard can be
swung upwards. Remove the nut securing the rear
brake torque stay to the anchor plate. then slacken
the left and right wheel spindle securing nuts. The
speedometer cable must be disconnected The rear
wheel is now free to be removed.
To refit the rear wheel first ensure that the spindle
nuts are sufficiently unscrewed then offer the wheel
to the swinging fork. Locate the adjuster caps over
the fork ends then lightly tighten the wheel spindle
nuts. Place the chain around the rear wheel
sprocket and connect up the brake anchor plate
torque stay. Refitting the chain may necessitate
slackening off both the left and right adjusters. It
is now necessary to ensure that the front and rear
wheels are aligned. This is shown in Section F4
below. Finally. lock up the two spindle nuts, ensure
the torque stay securing nut is tight. and reconnect
the speedometer cable.
SECTION F3
REMOVING AND REFITTING THE QUICKLY DETACHABLE REAR WHEEL
The Q.D. wheel is mounted on three bearings. two
ball journal bearings being situated in the hub and
one in the brake drum. The wheel is quickly
detachable by the simple method of splining the
hub into the brake drum thereby eliminating the
necessity of removing the rear chain etc . when
required to remove the wheel.
To remove the qUickly detachable rear wheel first
unscrew the wheel spindle from the right side of the
machine and drop out the distance piece between
the wheel and the fork end. Pull the wheel clear
of the spline and the brake drum when the wheel can
then be removed.
When replacing the wheel slight variations may be
F2
felt in the fit of the splines at various points. Select
the tightest position and mark with a small spot of
paint on the brake drum and corresponding spot on
the hub to facilitate replacement on future occasions.
In addition there Is a rubber ring which is assembled
over the splines on the wheel and is in compression
when the spindle is tight. This ring seals the spline
joint and prevents abrasive wear at the joint. If
it is perished or damaged fit a new one.
Replacement of the wheel is a reversal of the above
instructions and if the chain adjuster is not altered
it will not be necessary to re-check the rear wheel
alignment. However if this is necessary full details
are given in Section F4 opposite.
ClassicBike.biz
WHEELS, BRAKES AND TYRES F
SECTION F4
FRONT AND REAR WHEEL ALIGNMENT
When the rear wheel has been fitted into the frame
it should be aligned correctly by using two straight
edges or "battens", b o ~ t 7 feet long. With the
machine off the stand the battens should be placed
along-side the wheel, one either side of the machine
and each about four inches from the ground. When
both are touching the rear tyre on both sides of the
wheel the front wheel should be midway between
and parallel to both battens. Turn the front wheel
slightly until this can be seen. Any necessary
adjustments must be made by first slackening the
rear wheel spindle nuts, then turning the spindle
adjuster nuts as required ensuring that rear chain
adjustment is maintained. Refer to Fig. F1 for
illustration of correct alignment. Note that the
arrows indicate the adjustment required.
"Wrong" "Correct"
"Wrong"
Fig. F1. Aligning the front and rear wheels
F3
ClassicBike.biz
SECTION FS
BRAKE ADJUSTMENTS
BEFORE ENGINE NO. DU.66246
The front and rear brake shoes are semi-floating to
allow them to self centralise on the fulcrum pin. In
addition the front wheel brake shoe fulcrum pin is
adjustable and is identified by a hexagonal nut just
behind the fork bottom member on the anchor
plate. To adjust, slacken the nut, apply full pressure
to the front brake handlebar lever, and whilst hold-
ing this pressure. re-tighten the nut. This locks the
fulcrum pin in the position which ensures the max-
imum area contact of the brake shoes within the
brake drum.
AFTER DU_66246
The front brake being of the two leading shoe
variety has the length of the lever adjusting rod
pre set during assembly or reset after the brake
shoes have been replaced (see Section F6). The
shoes are however self centreing on the abutments
and are equipped with steel end caps for this
purpose. Cable adjustment is by means of the
knurled adjuster at the handlebar lever. Turn the
knurled nut anti-clockwise to take up the slack in
the control cable. The correct adjustment is with
not less then n in. (15 mm.) and not more than
tin. (3 mm.) slack in the inner cable, at the handle-
bar lever.
Any wear on the brake shoe lining is indicated
by the angular pOSition of the brake operaling
lever when the brake is fully applied. Fig. F2
illustrates the limiting pOSition before wear is
obviously excessive. This applies to both front and
rear brake operating levers. In this case the brake
should be dismantled and worn parts renewed as
shown in Section F6.
The adjustment of the front brake operating
mechanism is by means of a knurled adjuster nut
incorporated in the handlebar abutment. Turn the
F4
Fig. F2. Rear brake operating lever
nut anti-clockwise to take up the slack in the
control cable. The correct adjustment is with not
less than +.- in. (15 mm.) and not more than tin.
(3 m.m.) slack in the inner cable at the handlebar
lever.
The rear brake pedal is adjustable for position and
any adjustment for the pedal position to suit the
rider should be made before adjusting the free
movement. From the static position before the
brake is applied there should be about tin.
(12 c.m.) offree movement before the brake starts
to operate. The actual adjustment is by means of a
finger operated nut on the rear end of the brake
operated rod. Turn the nut clockwise to reduce the
clearance.
ClassicBike.biz
F
SECTION F6
STRIPPING AND REASSEMBLING THE BRAKES
FRONT BRAKE-TWO LEADING SHOE
FROM DU.66246
Access to the front brake shoes is gained by re-
moving the wheel (see Section F1). The brake plate
is retained by a centre nut. This is recessed into
the anchor plate and will require the use of a thin
box spanner. The brake plate assembly will then
lift away complete. Holding the brake plate with
one hand lift up one shoe as in Fig. F3 until it is
free. Disconnect one end of each brake return
spring and lift away the second shoe. Remove the
splitpin from the pivot pin at each end of the lever
adjustment rod and lift the pivot pins clear.
Remove the brake cam nuts and washers and
remove the return spring from the front cam.
Finally prise off the levers in turn and the brake
cams are free to be removed from the back of the
anchor plate.
To reassemble the brake shoes to the front anchor
plate first grease the spindles lightly and refit both
cams, wedge shape outboard on both. Refit the
outside return spring to the front cam and then
refit both brake cam levers (at a similar angle) and
secure with the plain washers and nuts. Fit the
abutment plates to the anchor plate, tag side
towards the anchor plate.
Fig. F3. Refitting shoe to 2LS brake
link the two shoes together with the return
springs (the narrow end of the shoe abuts to the
cam in each case). Both shoes fit with the radiused
end to the pivot. Fit the first shoe to both the cam
and abutment pad then stretch the springs by grasp
ing the second shoe and fitting it as shown in Fig. F3.
The complete brake plate is now ready for fitting
to the wheel. Replace the anchor plate over the
wheel spindle and lock it home with the spindle
nut, using spanner D181S.
Fig. F4. 2LS brake assembled showing position
of shoes
FRONT BRAKE BEFORE DU.66246 AND
ALL REAR BRAKES
Access to the brake shoes (front or rear) is obtained
by removing the wheel and unscrewing the central
nut which retains the brake anchor plate. If the
brake operating lever is then turned to relieve the
pressure of the shoes against the drum, the complete
brake plate assembly can be withdrawn from the
spindle. Slowly release the lever and continue until
the return spring can be removed, then take off
the brake shoes by the method shown in Fig. FS.
Remove the nut and washer securing the brake
lever to the cam spindle and remove the lever.
The cam spindle can then easily be withdrawn from
the plate.
FS
ClassicBike.biz
INSPECTION PROCEDURE
(1) Examine the anchor plate for cracks or distor-
tion, particularly in the brake cam housing.
(2) Clean out the grease in the brake cam spindle
and remove any n:st with a fine emery cloth.
(3) Inspect the return springs for signs of fatigue
and distortion. Renew them if necessary.
(4) Examine the brake drum for scoring or ovality.
F6
In the case of the rear wheel if the drum requires
skimming it should be removed from the wheel.
Do not skim more than -010 in. from the drum.
If the diameter exceeds more than that given in
"General Data" by more than 010 in. the
drum should be renewed.
In the case of the front wheel drum, scoring or
signs of ovality can be removed by similar
procedure but a large swing lathe of 18 in.
diameter is required.
Fig. FS. Refitting brake shoes
(5) Examine the brake shoes. The brake linings
should be replaced immediately the rivets
show signs of having worn level with the
linings face, or the linings show signs of cracks
or uneven wear. Replacement is described
fully in Section F7. Also check that the brake
shoes are not cracked or distorted in any way.
Fig. F6. Correct assembly of brake shoes onto front
anchor plate. Arrow indicates direction of rotation
To reassemble the brake shoes to the anchor plate
first place the two brake shoes on the bench in their
relative positions. Fit the return springs to the
retaining hooks, hooked ends uppermost, then
taking a shoe in each hand (see Fig. F5) and at the
same time holding the springs in tension, position
the shoes as shown over the cam and fulcrum pin
and snap down into position by pressing on the
outer edges of the shoes. Rotate the brake lever
in an anti-clockwise direction and engage the
return spring.
Note.-When replacing the brake shoes, note that
the leading and trailing brake shoes are not inter-
changeable in either the front or rear brake and
ensure that they are in their correct relative
positions as shown in Fig. F6.
Reassembly then continues by placing the anchor
plate over the wheel spindle and locking home
with the spindle nut. Refer to Section F4 for
final re-alignment of the wheels if this is found to
be necessary.
ClassicBike.biz
WHEELS. BRAKES AND TYRES F
SECTION F7
RENEWING THE BRAKE LININGS
The old linings can be removed by either drilling
through the rivets with a suitable sized drill (No. 23
154 in. dia.) or chiselling the lining off at the
same time shearing through the brass rivet.
Drilling is of course preferred and is best undertaken
from the inside of the shoe to remove the peened
over portion of the rivet.
New linings are supplied ready drilled. counter
bored and the correct shape. If no jig is available
for riveting. a simple method of spreading the
rivet is shown in Fig. F7.
Rivet the linings in the centre holes first. working
towards each end: great care must be taken to
ensure that the rivets are tight and that the linings
do not lift between the rivets. After fitting. all
sharp edges of the lining should be chamfered and
the leading and trailing edges tapered off to the
extent of,\- in. deep X t in. long.

Fig. F7. Rivetinglininl onto brake shoe
SECTION F8
REMOVING AND REFITTING THE WHEEL BEARINGS
Access to the wheel bearings differs in front and
rear wheels and therefore each wheel is dealt with
separately in this section.
FRONT WHEEL
Remove the front wheel from the fork and withdraw
the brake anchor plate from the brake drum.
Unscrew the retainer ring (left hand thread) using
service tool Z76.
The right bearing can be removed by using the
spindle and driving through from the left hand side.
Withdraw the backing ring and inner retaining
disc. (note that current wheels use a single part
replacing these two). To remove the left bearing.
spring out the circlip and insert the spindle from
the right side driving the bearing out complete with
inner and outer grease retainer plates.
Fully clean all parts in paraffin (kerosene). Clean
and dry the bearings thoroughly. Compressed air
should be used for drying out the ball races. Test
for end float and inspect the balls and races for any
signs of pitting. If there is any doubt about their
condition. the bearings should be renewed.
To refit the bearings. first insert the left inner
grease retainer, bearing. and outer dust cap using
a liberal amount of grease (see Section A2). Refit
the spring circlip and insert the shouldered end of
the wheel spindle from the right. using it as a
drift to drive the bearing and grease retainer until
they come up to the circlip. Re-insert the spindle
the opposite way round and re-fit the right hand
grease retainer disc and backing ring. Drive the
right bearing into position well smeared with
grease. then screw in the retainer ring (left hand
thread) until tight.
Finally. tap the spindle from the left to bring the
spindle shoulder up against the right bearing.
Refer to Fig. Fa or F9 for correct layout. Reassembly
then continues as the reversal of the above in
scructions.
F7
ClassicBike.biz
Fig. Fa. Latest wheel with twin leading shoe brake
Fig. F9. Exploded view of front wheel bearing arrangement (before DU.66246)
REAR WHEEL (STANDARD)
Remove the rear wheel then unscrew the anchor
plate retainer nut and withdraw the brake anchor
plate assembly. Withdraw the wheel spindle then
unscrew the slotted screw which serves to lock the
bearing retainer ring. The retainer ring can then
be unscrewed using service tool Z76. So that the
left bearing can be removed the central distance
piece must be displaced to one side to allow a drift
to be located on the inner ring of the left bearing.
lo do this, first insert a drift from the left and move
the distance piece to one side so that the grease
retainer shim collapses, as shown in Fig. F11. A
soft metal drift should then be inserted from the
right and the left bearing driven out. The speedo-
meter drive adaptor must first be unscrewed from
the hub before removing the right hand wheel
bearing. When this is done, withdraw the backing
ring. dam aged grease retainer and distance piece
Fa
then drive out the right bearing and dust cap using
a drift of approximately 1i in. diameter.
Fully clean all parts in paraffin (kerosene) and clean
and dry the bearing thoroughly. Compressed air
should be used for drying out if possible. Test the
end float and inspect the ball races for any signs of
indentation or pitting. If the condition of the
bearing is in doubt it should be renewed.
The damaged grease retainer shim usually can be
reclaimed for further service by carefully hammer-
ing it flat to restore its original shape.
To refit the bearings first drive in the right inner
grease retainer disc, the bearing and then press on
the outer dust cap ensuring that the bearing and
both cavities are well filled with grease. From the
left, insert the distance piece, grease retainer shim,
backing ring and having packed the bearing with
grease. press it in the hub and bring the distance
piece into line with the spindle. Screw in the
retainer ring and tighten it with service tool Z76
ClassicBike.biz
F
259
Fig. F10. Exploded view of the standard rear wheel
Finally, tighten the locking screw to ensure that
the bearing retainer ring is locked in position.
Reassembly then continues as a reversal to the
above instructions, but do not forget to refit the
outer distance piece before assembling the anchor
plate and brake shoe assembly.
Fig. F11. Collapsing the left bearing grease retainer
shim
The rear wheel is fitted with a brake drum to which
a detachable steel sprocket is retained by eight
bolts. Earlier wheels could be fitted with this
sprocket and brake drum as a direct replacement
for the original part.
REAR WHEEL (QUICKLY DETACHABLE)
Having removed the wheel from the swinging fork
as described in Section F3, the wheel hub can then
be dismantled. Hold the bearing sleeve by the slot
at the tapered end and unscrew the nut on the
right side. Use service tool Z76 (left hand thread)
to unscrew the locking ring and then lift off the
distance piece, felt washer and locating disc. The
bearing sleeve is a sliding fit and is easily with-
drawn. In order to remove the right bearing the
central distance piece has to be displaced radially
to allow a drift to be located on the inner ring of
the right bearing. This is done by inserting a drift
from the right and moving the centre distance piece
radially so that the grease retainer shim collapses.
Then insert a soft metal drift from the left and drive
out the right bearing. Withdraw the backing ring,
damaged grease retainer and distance piece; then
using a drift, drive out the left bearing and with-
draw the other grease retainer. Thoroughly clean
all parts in paraffin (kerosene) and fully dry the
bearings. Inspect the ball races for any signs of
indentation or pitting and renew if necessary.
Removal of the brake drum and sprocket assembly
from the swinging fork is achieved by first dis-
connecting the rear chain, torque stay and brake
operating rod, and then unscrewing the large
nut from the spindle sleeve.
Remove the brake shoes and anchor plate assembly
as described in Section F6. To remove the ball
bearing from the brake drum, first press out the
spindle sleeve and then remove the circlip from the
brake drum. The retainer and felt washer can then
be levered out to enable the bearing to be driven
out. Care should be taken to avoid damage to the
inner grease retainer when removing the bearing.
Clean the bearing in paraffin (kerosene) and check
that there is not excessive play or that the race
tracks are not indented or pitted. If in doubt,
renew the bearing. On reassembly pack the bear-
ings with grease and do not forget to dip the felt
washer in oil.
Reassembly is a reversal of the above procedure
referring to Fig. F12 for order of assembly and Sec-
tion F3 for refitting the wheel to the swinging fork.
F9
ClassicBike.biz
F
~
...
. ~

o
~
. c
260
Fig. F12. Exploded view of the quickly detachable I"ear wheel
Fig. F13. Exploded view of Q.D. rear- wheel (without speedometer drive)
Between engine numbers DU.13375 and DU.24875
the ball journal bearing type of wheel had no speedo-
meter drive gearbox. The order of assembly is
shown in Fig. F13.
Q.D. WHEEL PRIOR TO DU.13375
Prior to engine number DU.13375 the taper roller
bearing arrangement was used. Removal of the
wheel is as described in Section F3. Unscrew the
two locknuts on the right hand side of the spindle
sleeve (see Fig. F14) and then push the sleeve out of
the bearings from the right. Extract the inner
roller races and dust cover. The outer races are a
press fit and should be driven out from the opposite
side with a soft metal drift. Care should be taken
F10
not to damage the bearing backing rings. and inner
grease retaining shims.
Thoroughly clean all parts in paraffin (kerosene)
and fully dry the bearings. Check the roller bearing
surfaces for pitting and pocketing. Renew the bear-
ings if there is any indication of this.
To reassemble the wheel bearings, first press the
left and right backing rings and grease retainers
into the wheel hub and then press the left and right
outer races into the hub. Smear the rollers and
inner races with grease (see Section A2) and refit
them to their respective outer raCes. Offer the
threaded end of the spindle sleeve to the roller
ClassicBike.biz
F
bearings and then fit the right dust excluder cap
with felt washer and left dust excluder cap. (Refer
to Fig. F14).
Refit the right side distance piece and inner and
outer locknuts to the spindle sleeve, then tighten
the inner locknut, slacken it off one flat (-1-) turn and
lock it in position by tightening the outer locknut.
The sleeve and inner races should then rotate freely
without any "play" in the rollers being in evidence.
Reassembly is a reversal of the above. The order of
stripping and reassembly of the brake drum and
sprocket assembly is the same as for the later type
of Q.D. wheel.
Fig. F14. Exploded view of Q.D. rear wheel (earlier taper roller bearing type)
F11
ClassicBike.biz
F
SECTION F9
WHEEL BUILDING
Wheel building, or adjustment to the spokes to
realign the wheel rim should only be undertaken by
a specialist and these notes are for the specialist.
to enable him to follow Triumph practice. The
main point to remember is that all Triumph wheels
are built with the inside spokes on the brake drum
side taking the braking strain. This means the inside
spokes on the drum side are in tension when the
brake is applied in the direction of forward motion.
"G-CLAM P
,
f.. f 4' MS. STRIP
WITH TAPER AT ONE END
, 86
AI"
/ "
Fig. F1S. Sketch of wheel building gauge
The front wheel has 40 straight 8/10 gauge butted
spokes and is single cross-laced, whilst the rear
wheel has 40 8/10 gauge butted spokes, and is
double cross-laced.
A checking gauge suitable for Triumph wheels can
be made from two pieces of mild steel bar as shown
in Fig. F15 and this should be used to register from
the edge of the hub or brake drum onto the wheel
rim edge giving the relation indicated in the table.
This ensures the correct relation between the hub
and rim centre lines.
Wheel Rim Loca-
Dimensions
type tion
Inches m.m.
---
Front:
Standard WM2 Drum
-n
-04
--
Rear:
Standard WM2 Hub
1i
47-6
WM3 Hub
1!
4404
Q.D. WM2 Hub
1,J.
27
WM3 Hub
,
222
..
Table of .. Dish" Dimensional Settings for
Front and Rear Wheels
SECTION FlO
WHEEL BALANCING
Wheel balancing can be achieved by fitting standard
one ounce and half ounce weights which are readily
available, as required. All front wheels are balanced
complete with tyre and tube before leaving the
factory and if for any reason the tyre is removed it
should be replaced with the white balancing "Spot"
level with the valve. If a new tyre is fitted. existing
weights should be removed and the wheel re-
F12
balanced, adding weights as necessary until it will
remain in any position at rest. Make sure that the
brake is not binding while the balancing operation
is being carried out.
For normal road use it is not found necessary for the
rear wheel to be balanced In this way.
ClassicBike.biz

ClassicBike.biz
Fig. Fi9. Refitting the tyre to the wheel. Note valve
engaged in rim hole
Working from the valve, press the first bead over
the rim flange by hand, moving forward in small
steps and making sure that the part of the bead
already dealt with, lies in the well of the rim. If
necessary use a tyre lever for the last few inches,
as shown in Fig. F20. During this operation con-
tinually check that the inner tube is not trapped by
the cover bead.
Fig. F20. Levering the first bead onto the rim
the second bead into the well of the rim
diametrally opposite the valve. Insert a lever as
close as possible to the point where the bead passes
over the flange and lever the bead into the flange,
at the same time pressing the fitted part of the bead
into the well of the rim. Repeat until the bead is
completely over the flange. finishing at the valve
position (see Fig. F21).
Fig. F2t. Refitting the second bead over the wheel
rim. Care must be taken not to trap inner tube
Push the valve inwards to ensure that the tube
near the valve is not trapped under the bead.
Pull the valve back and inflate the tyre. Check that
the fitting line on the cover is concentric with the
top of the rim flange and that the valve protrudes
squarely through the valve hole. Fit the knurled
rim nut and valve cap. The tyre pressure should
then be set to the figure given in General Data.
SECTION FI2
SECURITY BOLTS
Security bolts are fitted to the rear wheel to prevent
the tyre "creeping" on the rim when it is subjected
to excessive acceleration or braking. Such
ment would ultimately result in the valve being torn
from the inner tube. There are two security bolts
fitted to the rear wheel, which are equally spaced
F14
either side of the valve and thereby do not affect
the balance of the wheel.
Note: The security bolt nuts must not be over-
tightened. otherwise excessive distortion may
occur.
ClassicBike.biz
WHEELS, BRAKES AND TYRES F
Where a security bolt is fitted the basic procedure
for fitting and removing the eyre is the same, but the
following instruction should be followed:-
(1) Remove the valve cap and core as described.
(2) Unscrew the security bolt nut and push the
bolt inside the cover.
(3) Remove the first bead as described.
(4) Remove the security bolt from the rim.
(5) Remove the inner tube as described.
(6) Remove the second bead and tyre.
For refitting the eyre and inner tube:-
(1) Fit the rim band.
Fig. Fll. Placing the security bolt in position
(2) Fit the first bead to the rim without the inner
tube inside.
(3) Assemble the security bolt into the rim.
putting the nut onto the first few threads (see
Fig. F1).
(4) Partly infiate the inner tube and fit it into the
the tyre.
(5) Fit the second bead but keep the security bolt
pressed well into the tyre. as shown in Fig. F23.
and ensure that the inner tube does not
become trapped at the edges.
(6) Fit the valve stem nut and infiate the tyre.
(7) Bounce the wheel several times at the point
where the security bolt is fitted and then
tighten the security bolt nut.
Fig. F23. Refitting the second bead with the security
bolt in position
SECTION Fil
TYRE MAINTENANCE
To obtain optimum eyre mileage and to eliminate
irregular wear on the tyres it is essential that the
recommendations governing eyre pressures and
general maintenance are followed. The following
points are laid out with this in mind.
(1) Maintain the correct inflation pressure as
shown in "General Data". Use a pressure
gauge frequently. It is advisable to check
and restore tyre pressures at least once per
week. Pressures should always be checked when
tyres are cold and not when they have reached
normal running temperatures.
(2) When a pillion passenger or additional load is
carried, the rear tyre pressure should be
increased appropriately to cater for the extra
load.
(3) Un necessary rapid acceleration and fierce braki ng
should always be avoided. This treatment
invariably results in rapid tyre wear.
(4) Regular checks should be made for fiints. nails.
small stones etc, which should be removed
from the tread or they may ultimately penetrate
and damage the casing and puncture the tube.
(5) Tyres and spokes should be kept free of 011.
grease and paraffin. Regular cleaning should be
carried out with a cloth and a little petrol
(gasoline).
(6) If tyres develope irregular wear. this may be
corrected by reversi ng the tyre to reverse its
direction of rotation.
(7) If a sidecar is fitted then correct alignment
should be maintained. The method for testing
sidecar align ment Is given in Section F14.
F15
ClassicBike.biz
F
SECTION FI4
SIDECAR ALIGNMENT
I n order that the tyres of a motorcycle and sidecar
combination are not subject to rapid tread wear and
to provide the best steering characteristics they
should be aligned as shown in the diagrams below.
First. align the front and rear wheels of the motor-
cycle as described in Section F4. and then. when it is
ascertained that this alignment is correct. the side-
car wheel should be set using two straight test bars
to the figure given in Fig. F24. Two battens about
6 feet long, S inches wide and 1 inch thick with one
edge on each of the boards planed perfectly straight
and square, would be suitable.
I
A
"
"
"
"
~ - - - -
-
B
Fig. F24. Aligning the sidecar wheel to the correct
amount of .. toe-in"
With the combination standing on a flat, smooth
floor place one of the long boards about 4 inches
from the floor (i.e. using spacers), alongside the rear
tyre with its straight edge touching the sides of the
tyres .. Straighten the front wheel until the board
is parallel with the sides of the front tyre, an equal
distance from both sides of the front wheel centre
line. Place the other long board also about 4 Inches
from the floor level with its straight edge touching
F16
123
the sides of the sidecar tyre. Front and rear
dimensions should then be measured, and the side-
car fixings adjusted until the front distance B is
between i inch (10 mm.) to ! inch (20 mm.)
smaller than the rear distance A. This distance is
referred to as the amount of "toe-in".
The motorcycle itself should also "lean out" and the
method for making this adjustment is shown clearly
in Fig. F2S. To do this, attach a plumb line to the
handlebar and measure the distances at the top
and bottom as shown. On the inner side of the
handlebar (i.e. nearer the sidecar) the plumb line
should be approximately 1 inch nearer the wheel
centre line at the bottom than at the top.
c
/ ,! / / / //D' /1111/ 1//1//;/;;1////1111/
124
Fig. FlS. Setting the amount of ulean-out" by usln, a
plumbline
ClassicBike.biz
DESCRIPTION
SECTION G
TELESCOPIC FORKS
REMOVING AND REFITTING THE NACELLE TOP COVER (6T)
REMOVING THE TELESCOPIC FORK UNIT
DISMANTLING THE TELESCOPIC FORK
INSPECTION AND REPAIR OF FORK COMPONENTS
RENEWING THE STEERING HEAD RACES
RENEWING THE FRONT FORK OIL SEALS
REASSEMBLING AND REFITTING THE FORK UNIT ...
TELESCOPIC FORK ALIGNMENT
ADJUSTING THE STEERING HEAD RACES
CHANGING THE FRONT FORK MAIN SPRINGS
THE HYDRAULIC DAMPER UNIT ...
Section
G1
G2
G3
G4
GS
G6
G7
G8
G9
G10
G11
G1
ClassicBike.biz
G TELESCOPIC FORKS
DESCRIPTION
The Triumph telescopic hydraulically controlled
front forks requires little attention other than an
occasional check of the external nut and bolts etc.
and the routine oil changes given in Section A1.
The fork uses short external main springs. Before
engine number DU.5825 an earlier type offork with
i
,J
internal springs anddifferent damping characteristics
was used. The capacity differs between the two
types of fork, so that it is essential that the appro-
priate quantity of oil is poured into each fork leg
when an oil change is to be carried out. The current
fork utilising shuttle valve damping is illustrated
below.
Fig. G1. Exploded view of telescopic (or-k (shuttle valve type)
G2
ClassicBike.biz
TELESCOPIC FORKS G
SECTION GI
REMOVING AND REFITTING THE NACELLE TOP COVER (6T)
Disconnect the leads at the battery terminals.
Unscrew and remove the steering damper knob.
Slacken the headlamp securing screw adjacent to the
speedometer dial and lever off the head lamp.
Disconne(t the lead from the main bulb, pilot
bulb and dip-sWitch (four snap connectors) and
disconnect the headlamp earthing lead.
Remove the two adaptor rim securing screws and
square nuts and withdraw the rims. Unscrew the
two front and two rear top cover securing bolts and
unscrew the left and right flash rear mounting
screws.
Disconnect the front brake cable at the handlebar
and thread it through the nacelle cover. Slacken off
the clutch cable adjuster at the handlebar and lift
the rubber sleeve at the gearbox and remove the
slotted cable adaptor, then disconnect the clutch
cable at the handlebar and thread it through the
nacelle top cover. The nacelle cover can then be
lifted to allow the drive cable and bulb holder to be
disconnected from the speedometer.
Disconnect the ammeter terminal leads and detach
the lighting switch and the ignition switch bakelite
connection plugs. The nacelle top cover is then free
to be removed.
Refitting the cover is the reversal of the above
instructions but reference must be made to the
relevant wiring diagram in Section H19 to avoid
incorrect connections being made. The blue!
brown lead from the battery -ve terminal should
be connected to the ammeter +ve terminal. To
check that the ammeter is correctly connected,
turn the ignition switch to "IGN". The ammeter
needle should defiect to discharge (-). If itdoes not,
reverse the ammeter terminal connections.
Finally, when the head lamp adaptor rim and light
unit are refitted the head main beam should be set
as described in Section H12.
SECTION G2
REMOVING THE TELESCOPIC FORK UNIT
Removal of the front forks is best achieved by
detaching the fork as a unit, removing the top lug
only whilst the stanchions and middle lug assembly
is lowered from the frame.
First, unscrew the small drain plugs at the bottom
of the fork adjacent to the wheel spindle lug and
drain the oil out by pumping the fork up and down
a few times.
Place a strong wooden box underneath the engine
so that the front wheel is about six inches clear of
the ground, then remove the wheel and mudguard
as shown in Section F1. Detach the headlamp unit
Section H12 and then detach the throttle cable
and air control cable. Detach the ignition lock
and switch on current models. The handlebar can
be removed by unscrewing the two self locking
nuts which secure the eye bolts underneath the top
lug. or, on machines without resilient mountings,
by removing the clamps.
Remove the steering damper plate pivot bolt, if
fitted, and then slacken the top lug pinch bolt and
unscrew the sleeve nut, Or blind nut, with a suitable
tommy bar. Unscrew the left and right stanchion
cap nuts using spanner No. D779 (D220 on earlier
models) and on earlier models withd raw the two
cap-nut-and-guide-tube assem bl ies.
Support the fork and then give the top lug a sharp
tap on the under-side until it is released from the
stanchion locking tapers. The stanchion and middle
lug assembly can then be lowered from the frame
headlug. If care is taken, the top ball race can be
left un-disturbed and the lower race balls collected
when the clearance is sufficient.
ALTERNATIVE METHOD
Alternatively the fork stanchions can be removed
whilst the middle lug. top lug and head races are
left un-disturbed. To facilitate extraction of the
stanchions from the top and middle lugs in this
G3
ClassicBike.biz
G TELESCOPIC FORKS
case service tool Z169 will be required (Z19 before
DU.68363. Remove the cap nuts, slacken the
middle lug pinch bolts and then unscrew the
two small hexagonal headed oil filler plugs (if
fitted) from the stanchion. Screw in the adaptor
plug (Z169 or Z19) and drive the stanchion until
it is free to be withdrawn from the middle lug, as
shown in Fig. G3. It should be noted that if the
stanchions are removed this wayan the later
models (frame No. DU.5825 onwards) a special
service tool will be required to refit them (see
Section G8 Part 2).
HANDLEBAR EYEBOLT ASSEMBLIES
Eyebolts are employed for fixing the handlebars on
TR6, T120 and U.S.A. TR6R and T120R. There are
three different types of fixing for the eyebolts. The
first two use the metalastic bushes fitted in the fork
top lug. The third type dispenses with these. See
Fig. G2.
(A) STANDARD RUBBER MOUNTED
HANDLEBAR (TR6 AND T120)
Note the hemispherical washer 'A' is fitted with the
rounded side towards the head lug. The washer 'B'
is radiused internally on one side only. The radius
must be towards the head of the eyebolt.
(B) U.S.A. RUBBER MOUNTED HANDLE-
BAR (TR6R AND T120R)
It will be noted that this arrangement uses an
additional support rubber with cup and inner
distance piece (C.D.E.) beneath the head lug. Again
note the radiused washer (A) must have the radius
towards the eyebolt head.
(C) RIGIDLY MOUNTED HANDLEBARS
(FOR USE WITH HANDLEBAR WIND-
SCREENS)
This arrangement dispenses with the metalistic
bushes in the head lug. These are replaced by pairs
of rigid bushes. There is no necessity to use the
radiused washers since both rigid bushes are
radiused in a similar manner. It tS not possible to
fit the bushes into the head lug incorrectly
Fig. G2.
T8
Rigid
Condition
Handlebar eyebolt order of assembly
SECTION G3
DISMANTLING THE TELESCOPIC FORK
There have been three types of forks fitted to unit
construction models. the earliest of the inside main
spring type, the second the redesigned outer main
spring type and the third the shuttle valve type.
To avoid confusion between the three basic types
this section is divided into three parts.
PART 1. FRAME DU.l0l TO DU.S824
Remove the front fork as shown in Section G3
then firmly grip the middle lug stem horizontally
in a vice and unscrew the hexagon headed oil
filler plugs and stanchion pinch bolts. Screw service
tool Z19 into the stanchion and drive it out of the
middle lug assembly. Alternatively, refit the stan-
chion cap nuts and use a hide mallet. When the
stanchions are removed withdraw the nacelle
G4
bottom covers and collect the two spring sealing
washers. On models fitted with gaiters slacken the
top and bottom gaiter securing clips and Withdraw
them.
Removal of the dust excluder sleeve nuts is facili-
tated by spanner D220 which should be used
when the stanchion and bottom member assembly
is firmly gripped in a vice by means of the wheel
spindle lug. The sleeve nut will be easily unscrewed
when it has been slackened initially by giving the
spanner a sharp knock with a hide or copper mallet.
Withdraw the stanchion, top bush and damping
sleeve from the bottom member. if necessary. by
giving the stanchion a few sharp pulls to release the
bush. If the stanchion cannot be freed from the
ClassicBike.biz
TELESCOPIC FORKS
G
bottom member due to some form of damage.
service tool No. Z127 will be required to extract
the stanchion. The tool should be attached to the
stanchion as shown in Fig. G4 ensuring that maxi-
mum thread engagement of the adaptor cap nut is
achieved.
The oil restrictor rod assembly is secured within
the bottom member by means of a hexagonal headed
bolt counter-bored into the wheel spindle lug.
When this bolt is unscrewed the restrictor rod
assembly can be withdrawn.
The bolt is sealed by means of an aluminium washer
which should be removed from the counter bore
and placed in safe keeping.
The bottom fork bearing bush is secured to the
stanchion by means ofa special slotted nut. Removal
of this nut is facilitated by spanner D220.
Fig. G3. Dismantling the telescopic fork using service
tool Z19.
PART 2. FRAME NO. DU.5825 TO DU.66245
Remove the front fork from the frame headlug by
the method shown in Section G2 and then grip the
middle Jug stem firmly in a vice and unscrew the
two small hexagon headed oil filler plugs (if fitted)
from the stanchion. Unscrew the two middle lug
pinch bolts, the top and bottom gaiter securing
clips if fitted. and. on earlier models (6T) withdraw
the lower nacelle shrouds.
Screw in service tool Z19, ora" old cap nut and drive
the stanchions out of the middle lug. When the
stanchions are removed, detach the spring covers,
springs and top and bottom washers.
At this stage the fork top shrouds can be removed.
It is advisable to renew the felt sealing washer when
reassembling the forks.
Removal of the dust excluder sleeve nut is facilitated
by service tool D527 which should be attached to the
sleeve nut whilst the wheel spindle lug is held
firmly in a vice. The sleeve nut has a right hand
thread and should unscrew easily once the nut has
been initially loosened by giving the spanner a sharp
tap with a hide mallet.
Note: If the hydraulic damping units shown in
Fig. G15 are fitted, it will be necessary to remove
them before the stanchions can be withdrawn from
the bottom members. To do this, unscrew the
hexagon headed bolt which can be seen counter
bored into the wheel spindle lugs.
When the dust excluder nut is removed, a few
sharp pulls should release the stanchion. bush and
damper sleeve assembly from the bottom member.
The restrictor rod securing bolt, the hexagon
headed restrictor securing bolt, seen counter-bored
into the wheel spindle lug. is sealed by means of an
aluminium washer which should be withdrawn
from the counter bore when the bolt is removed
and placed in storage and refitted on assembly.
PART 3. FRAME NO. DU.66245 ONWARDS
Remove the front fork from the frame head lug as
described in Section G1. Grip the middle lug stem
firmly in a vice and unscrew the two middle lug
pinch bolts and the top and bottom gaiter securing
clips. Screw service tool Z169 for machines after
DU.68363 (and Z19 prior to this number) into the
top of the stanchion (use an old cap nut in the
GS
ClassicBike.biz
G TELESCOPIC FORKS
Fig. G4. Extracting the stanchion from the bottom member using service tool Z127
absence of the correc.t tool) and drive the stanchions
out of the middle lug. When the stanchions are
removed. collect the spring abutments, springs,
gaiters and clips.
At this stage the fork top shrouds can be removed.
It is advisable to renew the felt sealing washer when
reass2mbling the forks.
Removal of the dust excluder sleeve nut is facilitated
by service tool D527 which should be attached to
the sleeve nut whilst the wheel spindle lug is held
firmly in a vice. The sleeve nut has a right hand
thread and should unscrew easily once the nut has
been initially loosened by giving the spanner a sharp
tap with a hide mallet.
When the dust excluder nut is re-
moved, a few sharp pulls should release
the stanchion, bush and shuttle valve
assembly from the bottom member.
If it is required to remove the cone
shaped restrictor from the bottom
member, merely release the securing
bolt.
G6
The hexagon headed restrictor securing bolt, seen
counter-bored into the wheel spindle lug, is sealed
by means of an aluminium washer which should be
withdrawn from the counter bore when the bolt is
removed and placed in storage and refitted on
assembly.
The shuttle valves are retained in the bottom end
of each stanchion by the bottom bearing retaining
nuts. Circlips are also fitted to prevent the shuttle
valves recessing into the stanchions (see Fig. GS).
Note that the shuttle valve fork type of stanchions
can be recognised immediately by the 8 bleed holes
just above the bottom bearing.
Fig. GS. Shuttle valve in position-note
stanchion bleed holes
ClassicBike.biz
TELESCOPIC FORKS G
SECTION G4
INSPECTION AND REPAIR OF FORK COMPONENTS
Telescopic fork components which have received
minor damage may possibly be repaired without
the need of new parts. The stanchions are the most
vulnerable part to damage and correction is often
possible if the damage is within the limits described
below. The top lug and middle lug are malleable
stampings and slight misalignment can be corrected
as described in the paragraphs below. The tools
required in order that a thorough check of the
various alignments can be made are an engineer's
checking table. set square. adjustable calipers and
a height gauge.
(1) Check the stanchions for truth by rolling them
slowly on a flat checking table. A bent stan-
chion may be realigned if the bow does not
exceed -h in. maximum. To realign the stan
chian. a hand press is required. Place the
stanchion on two swage fly" blocks at either
end and apply pressure to the raised portion of
the stanchion. By means of alternately pressing
in this way and checking the stanchion on a
flat table the amount of bow can be reduced
until it is finally removed.
(2) Inspect the top lug by fitting both stanchions
(if true) with the cap nuts tightened in position
as shown in Fig. G6. Check that the stanchions
are parallel to each other in both planes by
laying the assembly on a checking table and
taking caliper readings as shown. Using a set
square, check that the stanchions are at right
angles to the top lug.
Check the middle lug and stem for alignment
by inserting the stanchions until 6t in.
(16S em.) of the top of the stanchion protrudes
above the top surface of the middle lug as
shown in Fig. GS. Fit and tighten the pinch
bolts in position and then lay the assembly on
the checking table and with calipers check that
the stanchions lie parallel in the middle lug.
Fig. G6. Checking the top lug for alignment
The stanchions should also be checked for
being parallel in the other plane by Sighting
along the checking table top. A set square
should be used to check that the stanchions
are at right angles to the middle lug.
The middle lug stamping is malleable and
provided that the lug is not excessively
disorted. it can be trued qUite easily. Each
time a distortion correction is carried out
check that the assembly is true in both plan.s.
G7
ClassicBike.biz
G
TELESCOPIC FORKS
105
Fig. G7. Checking the stanchions and middle lug for alignment
(3) When the stanchions and middle lug assembly
has been trued. the top lug can be used to
check the position of the stem relative to the
middle lug. For this purpose. the distance
between the middle lug and top lug should be
the same on either side and to achieve this the
stanchions should be set in the middle lug to
the figure given in Fig. GS. When the top lug
is fitted the stem should be central in the top
lug hole. If it is not a long tube can be placed
over the stem and used to press the stem in the
- - ~ - - - - - "- - - "
correcting direction. When this is achieved,
re-check the fork assembly to ensure that the
original alignment has not been adversely
effected.
Check the stanchion bearing surfaces for wear,
particularly in forks where grey sintered iron
bushes have been used. It is permissable to
polish the stanchions with fine emery cloth to
remove roughness.
Fig. GS. Showing the correct angle between stanchion and stem centre lines
GS
ClassicBike.biz
TELESCOPIC FORKS
G
(4) Check that the bottom members are not
dented or damaged in any way by inserting
the stanchion and bottom bush assembly
and feeling the amount of clearance of the bush
within the bore of the bottom member. Any
restriction on movement indicates that the
bottom member is damaged and requires
renewing. The wheel spindle lug can be
checked for being at right angles to the bottom
member by machining a one * in. wide groove
in a tt inch diameter bar and bolting it in
position in the wheel spindle lug. A square may
then be used to check that the bar is
perpendicular to the bottom member. If the
degree of error is excessive, no attempt should
be made to realign the wheel spindle lug, the
bottom member should be renewed.
(5) Examine the top and bottom bushes for wear
by measuring the bore diameter of the top bush
and the outside diameter of the bottom bush
and comparing them with the figures given in
General Data. Also, the bushes can be checked
against their respective mating surfaces: put
the top bush over the stanchion and at about
eight inches from the bottom of the stanchion
check the diametral clearance at the bush.
An excessive clearance indicates that the bush
reqUires renewing. As described above. the
bottom bush can only be checked by fitting it
to the stanchion and inserting the stanchion
into the bottom member to a depth of about
eight inches whilst the diametral clearance
is estimated from the amount of "play".
As a matter of course, replace any grey sintered
iron fork bushes with the sintered bronze type
bushes for improved wear.
(6) Examine the main springs for fatigue and cracks
and check that both springs are ofapproximate
equal length and within tin. (13 em.) of the
original length on the earlier long type main
spring, and within! in. of the original length
382
Fig. G9. Checking the bottom member wheel spindle
lug for truth
in the case of the later short main spring. The
figures for the original length are given in
"General Data".
(7) Inspect the cups and cones for wear in the form
of pitting or pocketing. This will appear as a
series of small indentations in the ball tracks
and indicates that both the races and the balls
reqUire renewing.
The cups shou Id be a tight interference fit i ntothe
frame headlug. Slackness there usually indicates
that the headlug cup seatings are distorted.
The bottom cone should be a tight fit onto the
middle lug stem and the top cone and dust cap
assembly should be a close sliding fit over the
stem. Slackness of the cone on the stem indi-
cates that the steering races have not been in
correct adjustment. In this case, if the new cone
is not a tight fit over the stem. then either the
stem and middle lug assembly should be re-
newed or in certain cases a proprietary sealant
may be used to secure the cone in position.
G9
ClassicBike.biz
G TELESCOPIC FORKS
SECTION GS
RENEWING THE STEERING HEAD RACES
The cups can be driven out of the head lug from the
inside by inserting a long narrow drift and locating
it on the inner edge of the cups. When the cups are
removed the bore of the head lug should be cleaned
thoroughly and the new cups driven in by using a
hammer and aluminium drift or a piece of hard wood
interposed to check the blow. Care should be
taken to ensure that the cup enters into the headlug
squarely and that no burrs are set up due to misalign-
ment.
The bottom cone can easily be removed from the
stem by inserting levers on either side and prising
the cone upwards. When it has been removed.
clean the stem and remove any burrs with a fine
grade file before fitting the new cones. To ensure
that the new cone is driven on squarely service
tool number Z24 should be used. To assist in the
assembly of the cone a small amount of grease may
be smeared on the middle lug stem. If the service
tool is not available a suitable drift can be made from
a piece of 1+.- in. (27 em.) inside diameter tube
9 inches long. Note that when new cups and cones
are fitted. new balls must also be used. The correct
quantity is 40 off t in. diameter balls-20 top race
and 20 bottom race.
SECTION G6
RENEWING THE FRONT FORK OIL SEALS
Fig. G10. Removing the oil seal from the earlier dust
excluder sleeve assembly using service tool Z137
Gl0
On the current front fork the oil seal is pressed
into the dust excluder sleeve nut and is freely
accessible from both sides. The oil seal can be driven
out by inserting a suitable drift and locating it on
the oil seal at one of the peripheral slots.
The new oil seal should be pressed in with the lip
and spring side facing the threaded end of the sleeve
nut and a check should be made to ensure that it is
fully and squarely engaged.
Removal of the oil seal from the dust excluder
sleeve assembly on the earlier type front fork is
achieved by means of service tool Z137. The dust
excluder nut should be fitted to the holder as shown
in Fig. G10 and the drift inserted and used to drive
the sleeve out. This will enable the oil seal to be
driven out in the same direction.
When fitting the new oil seal, ensure that it is
pressed in with the spring and lip side towards the
threaded end of the bore and press the sleeve in
until it is flush with the rear face of the oil seal.
A rubber '0' ring seal is fitted on late machines
into the thread of the chrome dust excluder. It is
advisable to remove the 'a ring which will almost
certainly be compressed and to fit a new one to
each dust excluder.
ClassicBike.biz
TELESCOPIC FORKS G
SECTION G7
REASSEMBLING AND REFITTING THE TELESCOPIC FORK UNIT
To cater for the three basic types of telescopic forks
fitted to Triumph machines this section is divided
into three parts-part one deals with the earlier
type front fork, part two deals with the external
spring type front fork, the assembly of which
requires service tool Z161, and part three deals
with the current fork with shuttle valve damping.
PART 1. FRAME NO. DU.l0l TO DU.5824
First, offer the stanchion and bottom bush assembly
Into the bottom member and refit the damper
sleeve and top bush. Offer the dust excluder sleeve
nut and oil seal assembly over the stanchion using
a smear of oil to assist assembly. and then tighten
the sleeve nut in position using spanner D220. With
the stanchion in its lowest position offer the
restrictor rod assembly to the stanchion and refit
the hexagonal restrictor rod securing bolt and
aluminium washer until all but a few threads are
engaged in the restrictor rod.
Work the restrictor rod round until the location
slot in its base is level with the location plug hole
then refitting the plug, tighten the restrictor rod
securing bolts. Do not forget that a fibre washer
is fitted under each of the location plugs.
Fig. GU. Reassembling the telescopic fork
Thoroughly clean the head race cups and cones and
smear the ball tracks with the recommended grease
(see Section A2). Place the ball bearings in the cups
(20 top, 20 bottom) using grease to hold them in
position. Offer the middle lug and stem assembly
to the headlug and lower the top cone and dust
cover assembly into position. Refit the top lug and
sleeve nut. tighten the sleeve nut until dll the slack
is taken up. Refit the sleeve nut pinch bolt finger
tight and align the middle lug and top lug. Assemble
the left and right bottom nacelle covers to the
middle lug and insert the pinch bolts, but only
screw on the nuts finger tight.
Offer the right stanchion (with brake anchor plate
locating boss fitted) to the middle lug and rotate it
until the oil filler plug hole is accessible to the
headlamp aperture. Force the stanchion upwards
using the bottom member as an impulse driver (see
Fig. G11). When the taper is engaged in the top lug.
temporarily tighten the pinch bolt then repeat the
procedure for the left stanchion. Finally, pour
t pint (150 c.c.) of the recommended grade of oil
into each fork leg and then refit the main springs.
Screw in the left and right cap nuts and guide tube
assemblies until several threads are engaged, then
slacken the middle lug pinch bolts and then return
to fully tighten the cap nuts using spanner No.
D220. When this is achieved, adjust the steering
head races as described in Section G10 and retighten
the middle lug pinch bolts and sleeve nut pinch bolts
Refit the oil filler plugs (if fitted) not forgetting the
two sealing fibre washers. Reposition the handle-
bar but do not forget to refit the washers and
self-locking nuts where the handlebars are rubber
mounted.
Reassembly then carries on as a reversal of the
removal instructions but reference should be made
to the relevant wiring diagram 1n Section H19 when
refitting the nacelle unit.
PART 2. FRAME NO. DU.5825 TO DU.66245
Assemble the stanchion to the bottom member
and fit the damper sleeve and top bush, Then
screw on the dust excluder steeve nut and oil seal
assembly having used jointing compound on the
outer member threads and hold the bottom member
in a vice by means of the wheel spindle lug whilst
the sleeve nut is tightened using service tool D527.
G11
ClassicBike.biz
G TELESCOPIC FORKS
'0' Ring Seals are fitted between the dust excluder
sleeves and the bottom members on later forks. If
not already fitted it would be worthwhile incor-
porating these '0' Rings on any External Spring Fork
('0' Ring Part Number H2119).
Note.-From engine number DU.1337S the
damper sleeve is stepped and when reassembling.
the sleeve is pressed in with the thick end pointing
downwards.
To refit the oil restrictor rod first slide the rod
down inside the stanchion and then use a piece of
tubing about 2 feet long and tin. (13 cm.) inside
diameter, to grip the restrictor rod whilst several
threads of the hexagon headed securing bolt are
engaged. Do not forget to replace the aluminium
sealing washer which fits over the securing bolt.
Screw in the small location plug and with the tubing
rotate the restrictor rod until the location slot is
aligned with the plug, then tighten the securing
bolt. Do not forget to fit new fibre washers under
each of the two location plugs. When both stan-
chions are assembled in this way. fit the plain thrust
washer, main spring. cover and felt washer over
each stanchion. On models fitted with nacelle type
headlamp there is also a plain steel washer fitted
underneath the felt washer to give additional
clearance. On models fitted with a head lamp unit
the gaiters should be fitted over the springs and
clamped up top and bottom on to the thrust washer
and sleeve nut respectively.
Align the middle lug and top lug and position the
left and right lower nacelle cover and then insert the
middle lug pinch bolt and fit the nuts finger tight.
Offer the right stanchion assembly (with welded
boss for front brake anchor plate location) and
engage as much of the stanchion as possible in the
middle lug. To pull the stanchion up to the top lug.
service tool Z161 is required which should be
inserted into the top lug and the plug adaptor
screwed into the stanchion top. The stanchion can
then be drawn easily up to the required level and
when this is achieved, temporarily tighten the pinch
bolt, remove the tool and screw in the cap nut until
several threads are engaged. Repeat this procedure
for the left stanchion assembly and then remove
both cap nuts and pour t pint (190 c.c.) of the
recommended grade of oil (see Section A2) into
each fork leg.
G12
Fig. Gi2. Reassembling the telescopic fork, using
service tool No. Z161
Refit the cap nuts until several threads are engaged
then slacken off the middle lug pinch bolt and fully
tighten the cap nuts. On models with nacelle type
front forks the stanchions will require turning
prior to tightening the cap nuts so that the oil
filler plug holes are accessible through the h eadlamp
aperture. When this is achieved. adjust the steering
head races as described in Section G10 and then
tighten the sleeve nut pinch bolt and two middle
lug pinch bolts. to the torque figures given in
"General Data"
Reassembly continues as the reversal of the dis-
mantling procedure. referring to Section H19 for
the relevant wiring diagram and Section H12 to
set the headlamp main beam.
PART 3. FRAME No. DU.66246 ONWARDS
Before reassembly remember that machines after
DU.68363 use unified threads on the stanchions.
cap nuts and bottom bearing nuts. Machines be-
tween DU.66246 and DU.68363 though also using
shuttle valve damping have C.E.I. threads. It will
ClassicBike.biz
TELESCOPIC FORKS G
be noted that the parts involved are not inter-
changeable except as a set.
Assemble the bottom bush to the stanchion, fit the
shuttle valve, large diameter uppermost and secure
with the bearing retaining nut. Fit the circlip to
prevent the shuttle valve sliding back into the
stanchion.
If the cone shaped restrictor has been removed, it
must be refitted to the bottom member at this
stage, being retained by the hexagon headed bolt
and aluminium sealing washer fitted into the wheel
spindle cutaway recess. To hold the restrictor in
position whilst the bolt is fitted, use the stanchion
complete with shuttle valve as a gUide.
Offer the stanchion and bottom bush assembly into
the bottom member and refit the top bush. Offer
the dust excluder sleeve complete with '0' ring
and seal over the stanchion which should be lightly
smeared with oil. Tighten the dust excluder in
position over the bottom member using spanner
0527. Drop the spring into position over the
stanchion followed by the gaiter and clips, top
spring abutment and cork washer. The gaiters
should be secured top and bottom with the clips
over the top abutment and dust excluder. Align
the top and middle lug. Fit the left and right fork
top shrouds, and insert the middle lug pinch bolts
and nuts finger tight.
Offer the right stanchion assembly (With welded
boss for front brake anchor plate location) and
engage as much of the stanchion as possible in the
middle lug. To pull the stanchion up to the top lug,
service tool Z170for U.N.F. threads or Z161 for C.E.1.
threads is required which should be inserted into
the top lug and the plug adaptor screwed into the
stanchion top. The stanchion can then be easily
drawn up to the required level and when this is
achieved temporarily tighten the pinch bolt,
remove the tool and screw in the cap nut until
several threads are engaged. Repeat this procedure
for the left stanchion assembly and then remove
both cap nuts and pour t pint (200 c.c.) of the
recommended grade of oil (see Section A2) into
each fork leg.
Refit the cap nuts until several threads are engaged
then slacken off the middle lug pinch bolt and fully
tighten the cap nuts with spanner D779. When
this is achieved, adjust the steering head races as
described in Section G10 and then tighten the
sleeve nut pinch bolt and two middle lug pinch
bolts, to the torque figures given in "General
Data".
Reassembly continues as the reversal of the dis-
mantling procedure, referring to Section H19 for
the relevant wiring diagram and Section H12 to
set the head lamp main beam.
G13
ClassicBike.biz
G TELESCOPIC FORKS
SECTION G8
TELESCOPIC FORK ALIGNMENT
To facilitate checking the alignment of the
telescopic fork legs there is available service
tool Z103 the dimensions of which are shown in
Fig. G13.

3'
,..
8
it
To check the front fork alignment, the front wheel
and mudguard must be removed and a spare wheel
spindle bolted in position. If a spare spindle is not
available use the one removed from the front wheel
as described in Section F8.
,

i
--
" "
STD
4
"4
i6 1-
3"
4L
(f-'
---------- - THESE FAqS TO BE LEVEl_ ------__ '-'fl.
------ -T"
-
;:J2R
M.$ At-JGl,E- 2 OFf'
ADIUS
r
y-
14
---J
+-
IJ
"
I
-- !
@
,
7
I
"fl
I
m

1----
G14
- - -
-- ----
__
r- Il"--
,
,
,
IEb
: '
/
-,--
'\
,
,
,
,
,
,
,
,
/
,
$
,
:
-
_RAQllJ'?_ THESE
,
,
,
,
,
,
,
,
,

: '
,
,
,
,
,
,
,
,
:El
: '
,
:

"
-- -
---
I
I
I"
1
"
I
1
I
I
I"
'2
-
1
"-8 H
TO
,r.-CA
OLES
SUIT
-PSCREWS
96
Fig. GU. Telescopic fork leg alignment gauge service tool Z103
ClassicBike.biz
TELESCOPIC FORKS G
Hold the alignment gauge firmly against the fork
legs as shown in Fig. G14 and check that the
gauge contacts at all four corners. If the gauge does
not make contact at point A then this indicates
that point B is too far forward. To remedy this,
slacken off the two middle lug pinch bolts and
the stem sleeve nut pinch bolt and give point C a
sharp blow using a hide mallet or a hammer used
in conjunction with a soft metal drift.
Check the alignment again with the gauge and again
give correcting blows in the above mentioned
manner until the amount of rock at anyone corner
does not exceed -b inch. When this is achieved,
tighten all three pinch bolts and then finally apply
the gauge to check that tightening has not caused
distortion.
A
D
B
89
FIB. G14. Checking the telescopic fork leg alilnment
with service tool 2103
SECTION G9
ADJUSTING THE STEERING HEAD RACES
When a new machine has covered the 500 miles
(running-in period) It will be necessary to check
the steering head races for excessive play due to
the balls, cups and cones bedding down.
Also, after long periods, the head races may
require adjusting to compensate for any wear that
may have taken place. The working clearance of the
balls in the tracks of the cups and cones is controlled
by the fork stem sleeve nut which is locked in
position by means of a pinch bolt at the rear of the
top lug. When the pinch bolt is slackened the sleeve
nut can be turned to increase or decrease the head
race worki ng clearance.
Mount the machine with the front wheel clear of the
ground and balance the front fork so that both the
front and rear wheels are aligned. When the fork
is tilted to either side of its central position It should
just fall to its full lock position. If the fork will do
this then the head races are not over tight and
conversely to check that they are not too loose,
hold the top lug with the left hand (with the
head lamp unit removed on models fitted with
nacelle type front forks) and hold the top portion
of the front mudguard in the right hand and then
attempt to "rock" the fork. If there is any "rock"
in evidence, then tighten the stem sleeve nut
* turn and check again. Continuing this way
until the fork will not rock but will turn from lock
to lock easily. When this is achieved, re-tighten
the stem sleeve nut pinch bolt.
G15
ClassicBike.biz
G TELESCOPIC FORKS
SECTION GIO
CHANGING THE FRONT FORK MAIN SPRINGS
First, place a strong box underneath the engine so
that the motorcycle is mounted with the front
wheel off the ground.
Removing the springs necessitates withdrawing the
complete fork leg assemblies. leaving the top and
middle lugs in the frame (see Fig. Gll). This is
accomplished by removing the top nuts using
spanner D779 or D220 before DU.68363. The pinch
bolts should be slackened and the leg assemblies
driven out with tool Z169 or tool Z19 before
DU.68363. The springs can then be lifted off over
the stanchions. Reassembly can then be under-
taken by offering up the stanchions as in Section G8
Part 2.
Removing the main springs on models fitted with the
inside-spring type front fork i.e. frame No. DU.l0l
to DU.5824. necessitates removal of the nacelle
top cover (if fitted) and handlebars.
When the cap nut-and-guide-tube assemblies are
removed the main springs can be withdrawn and
the new ones fitted.
When the cap nuts are refitted. they must be fully
retightened. If necessary use a piece of tubing
which will increase the leverage to about 12 in. to
finally tighten the nuts. Reassembly then continues
as a reversal of the dismantling procedure.
The table below shows the spring rates and colour
codes for the purposes designated.
LOAD at
SPRING FITTED
RATE LENGTH COLOUR
MODEL Ib./in. Ibs. CODE
All models after DU.13374
Solo 26t 22 Yellow/Blue
Sidecar 32t 26t Yellow/
Green
All models DU.5825 to DU.3374
Solo 30 50 Unpainted
Sidecar 37 60 Yellow/
White
ENGINE No. DU.l0l to DU.5824
6T/T120 Solo 32 85 Black/Green
6TfT120
Sidecar* 37 98 Red/White
TR6 Solo 30 46 Black/White
TR6 Sidecar 37 56 Black/Red
With longer sidecar outer members
SECTION Gil
THE HYDRAULIC DAMPING UNIT
Fig. G13 shows an exploded view of the damping
unit which may be fitted to certain types of tele-
scopic'front forks. To fit these units, two alternative
stanchion cap nuts are required with a threaded
hole into which the top of the damper unit rod
screws. Locknuts are provided to secure the cap
nut to the rod. Note that on a machine fitted with
these damper units. if the rod should become
detached from the cap nut for any reason. it must
be remembered that it will fall back into the stan-
chion. Therefore when fitting the fork to the frame
a check should be made to ensure that the operation
of fitting the damper unit rod to the cap nut has
not been forgotten.
The bottom of the damper unit is secured in the
same way as the restrictor rod on standard machines
(Section G8). i.e. by means of a hexagon headed
G16
bolt countersunk into the wheel spindle recess.
To dismantle the unit. first grip the body carefully
in a vice. then unscrew the adaptor nut (two flats)
and withdraw the rod assembly. The cap is removed
by unscrewing the locknut from the end ofthe rod
and withdrawing the sliding fit oil restrictor cup.
When reassembling the damper. ensure that the
pin is in position and when the locknut is tight, use
a centre punch to prevent the nut subsequently
unscrewing.
Ensure that the oil holes in the stem are free from
blockage and refit the rod assembly to the body.
After assembly. test the unit for damping efficiency
by immersing the lower end of the unit into oil and
pumping the centre rod a few times. There should
be little or no resistance on the down stroke and a
good resistance on the up stroke.
ClassicBike.biz
TELESCOPIC FORKS
Fig. G1S. Exploded view of telescopic fork internal hydraulic damper unit assembly
Before DU.66246 (Alternative equipment)
G
G17
ClassicBike.biz
INTRODUCTION
SECTION H
ELECTRICAL SYSTEM
BATTERY INSPECTION AND MAINTENANCE Hl
DESCRIPTION
(a) ROUTINE MAINTENANCE ...
(b) MAXIMUM PERMISSABLE ELECTROLYTE TEMPERATURES DURING CHARGING
BATTERY CONNECTIONS-TWO 6 VOLT BATTERIES IN SERIES H2
COIL IGNITION SYSTEM H3
DESCRIPTION
(a) CHECKING THE LOW TENSION CIRCUIT FOR CONTINUITY ...
(b) FAULT FINDING IN THE LOW TENSION CIRCUIT
(c) IGNITION COILS ...
(d) CONTACT BREAKER
(e) CONTACT BREAKER FROM DU.66246
(I) CHECKING THE HIGH TENSION CIRCUIT ...
(g) CHECKING THE EMERGENCY STARTING CIRCUIT
SPARKING PLUGS H4
CHARGING SYSTEM H5
DESCRIPTION
(a) CHECKING THE D.C. INPUT TO BATTERY
(b) CHECKING THE ALTERNATOR OUTPUT .. .
(c) RECTIFIER MAINTENANCE AND TESTING .. .
(d) CHECKING THE CHARGING CIRCUIT FOR CONTINUITY
(e) MAKING A 1 OHM LOAD RESISTOR
ZENER DIODE CHARGE CONTROL AND TEST PROCEDURE H6
ZENER DIODE LOCATION ... H7
A.C. IGNITION (E.T.) AND A.C. LIGHTING SYSTEMS H8
DESCRIPTION
(a) A.c. IGNITION ... ... ... ...
(b) TESTING THE A.c. IGNITION SYSTEM
(c) CHECKING THE A.C. ALTERNATOR OUTPUT
(d) DIRECT LIGHTING SYSTEM
ALTERNATOR AND STATOR DETAILS (Specifications and Output Figures) ... H9
ELECTRIC HORN ... Hl0
HEADLAMP ... Hll
DESCRIPTION
BEAM ADJUSTMENTS
HEADLAMP REMOVING AND REFITTING H12
TAIL AND STOPLAMP UNIT H13
FUSES ... H14
IGNITION SWITCH H15
IGNITION CUT-OUT BUTTON H16
WARNING LAMPS H17
CAPACITOR IGNITION (ModeI2MC) H18
HEAT SINK REQUIREMENTS
IDENTIFICATION OF CAPACITOR TERMINALS
TESTING
WIRING AND INSTALLATION ...
SERVICE NOTES ...
WIRING DIAGRAMS H19
ALL MODELS FROM DU.66246 (HOME)
ALL MODELS FROM DU.66246 (EXPORT)
COIL IGNITION-12 VOLT MODELS WITH SEPARATE HEADLAMP (FROM DU.24875)
HOME ... ... ... . ..
COIL IGNITION-12 VOLT MODELS WITH SEPARATE HEADLAMP (FROM DU.24875)
EXPORT USA ... ...
E.T. IGNITION-(A.C. MAGNETO) MODELS
COIL IGNITION-12 VOLT MODELS WITH NACELLE (FROM DU.24875)
COIL IGNITION-12 VOLT MODELS (BEFORE DU.24875)
COIL IGNITION-6 VOLT MODELS... ...
COIL IGNITION-6 VOLT POLICE MODELS WITH BOOST SWITCH ...
Hl
ClassicBike.biz
H ELECTRICAL SYSTEM
INTRODUCTION
The electrical system is supplied from an alternating
current generator contained in the primary chain
case and driven from the crankshaft. The generator
output is then converted into direct current by a
silicon diode rectifier. The direct current is
supplied to a 12 volt 8 ampere/hour battery with a
Zener diode in circuit to regulate the battery
current.
The current is then supplied to the ignition system
which is controlled by a double contact breaker
driven direct from the exhaust camshaft. The
contact breaker feeds two ignition coils, one for
each cylinder.
On 6volt coil ignition machines prior to DU24875 in
the case of a discharged battery the emergency
position of the ignition switch supplies output
direct from the generator through one pair of
contacts and one ignition coil to enable the engine
to be started. As soon as the engine has been
started the ignition switch must be returned to the
normal position or burning of the contact breaker
poi nts wi II take place.
The routine maintenance needed by the various
components is set out in the following sections. All
electrical components and connections including
the earthing points to the frame of the machine
must be clean and tight.
No emergency start faCility is provided on current
12 volt machines. On these models there is
however sufllcient voltage to start the machine
when a discharged battery is in circuit.
Earlier models used a single 6 volt battery on 6T
up to engine number DU.5824 and T120 or TR6 up
up engine number DU.24874. Between DU.5824
and DU.24874 the 6T only used a 12 volt electrical
system. On these models and on certain machines
before DU.44394 two MKZ9E 6 volt batteries were
fitted in series (see Fig. H1) to give 12 volts.
Before engine number DU.24875 the generator
was connected to give alternative charge rates,
governed by the positions of the lighting switch.
SECTION HI
BATTERY INSPECTION AND MAINTENANCE
The battery containers are moulded in translucent
polystyrene through which the acid level can be
seen. The battery top is so designed that when the
cover is in pOSition, the special anti-spill filler plugs
are sealed in a common venting chamber. Gas from
the filler plugs leaves this chamber through a vent
pipe union at the side of the top. The vent at the
other side of the top is sealed off. Polythene tubing
is attached to the vent pipe union to lead corrosive
fumes away from parts of the machine which may
otherwise suffer damage.
To prepare a dry-charged battery for service, first
discard the vent hole sealing tape and then pour
into each cell pure dilute sulphuric acid of appro-
priate specifIC gravity to THE COLOURED LINE.
(See table a). Allow the battery to stand for at
least one hour for the electrolyte to settle down,
thereafter maintain the acid level at the coloured
line by adding distilled water.
H2
Fig. H1. Exploded view of battery
ClassicBike.biz
ELECTRICAL SYSTEM
H
H1. PART A. ROUTINE MAINTENANCE
Every week examine the level of the electrolyte in
each cell. Lift the battery out of the carrier so that
the coloured filling line can be seen. Add distilled
water until the electrolyte level reaches this line.
Note.-On no account should batteries be
topped up to the separator guard but only
to the coloured line.
With this type of battery, the acid can only be
reached by a miniature hydrometer, which would
indicate the state of charge.
Great care should be taken when carrying out these
operations not to spill any acid or allow a naked
flame near the electrolyte. The mixture of oxygen
and hydrogen given off by a battery on charge, and
to a lesser extent when standing idle. can be
dangerously explosive.
The readings obtained from the battery electrolyte
should be compared with those given in table (a). If
a battery is suspected to be faulty it is advisable to
have it checked by a Lucas Depot or Agent.
SPECIFIC GRAVITY OF ELECTROLYTE
FOR FILLING THE BATTERY
U.K. and Climates Tropical Climates
normally below over
90'F (322'C) 90'F (32'2'C)
Filling Fully charged Filling Fully charged
1260 1 280/HOO 1210 1220/1-240
Every 1,000 miles (1,500 k.m.) or monthly, or more
regularly in hot climates the battery should be
cleaned as follows. Remove the battery cover and
clean the battery top. Examine the terminals: if
they are corroded scrape them clean and smear
them with a film of petroleum jelly, such as vaseline.
Remove the vent plugs and check that the vent
holes are clear and that the rubber washer fitted
under each plug is in good condition. Note that
current batteries have the plugs en bloc and no
washers are used on this type.
-
H1. PART B. MAXIMUM PERMISSABLE
ELECTROLYTE TEMPERATURE
DURING CHARGE
Climates Climates Climates
normally between frequently above
Below 80'F 80-100'F 100'F
(2rC) (27-38'C) (38'C)
100'F 110'F 120'F
(38'C) (43'C) (49'C)
Notes.
The specific gravity ofthe electrolyte varies with the
temperature. For convenience in comparing specific
gravities, they are always corrected to 60F., which
is adopted as a reference temperature. The method
of correction is as follows:
For every 5'F. below 60'F. deduct 020 from the
observed reading to obtain the true specific gravity
at 60'F. For every 5'F. above 60'F., add 020 to the
observed reading to obtain the true specific gravity
at 60'F.
The temperature must be indicated by a thermo-
meter haVing its bulb actually immersed in the
electrolyte and not the ambient temperature. To
take a temperature reading tilt the battery side-
ways and then insert into the electrolyte.
H3
ClassicBike.biz
H ELECTRICAL SYSTEM
SECTION H2
BATTERY CONNECTIONS-TWO 6 VOLT BATTERIES IN SERIES
Early machines in the 12 volt series were fitted
with two six volt batteries connected as shown.
Later machines incorporated a single 12 volt
battery Lucas type PUZSA.
On machines where two six volt batteries are fitted.
these are connected in series to provide a twelve
volt source of power.
It is extremely important that the batteries are
correctly connected into the circuit to avoid
damage to the electrical equipment. All machines
use a positive (+ vel earth system. Refer to Fig. H2
which shows the correct method of connecting the
batteries.
TO HARNESS-
I
1-
I
+
= EARTH (GROUNDI
Fig. H2. Schematic diagram of 2 six volt batteries in
series. (Note:-a]5 amp fuse is usually incorporated
between battery positive and earth (ground
SECTION H3
COIL IGNITION SYSTEM
DESCRIPTION
The coil ignition system comprises two ignition
coils and a contact breaker fitted in the timing
cover and driven by the exhaust camshaft. The
ignition coils are mounted underneath the petrol
tank one either side of the main tank tube. Access
to the coils is achieved by removing the fuel tank
as shown in Section E1. Apart from cleaning the
coils, in between the terminals and checking the
low tension and high tension connections. the coils
will not require any other attention. Testing the
ignition coils is amply covered in H3 Part C below
whilst testing the contact breaker is described in
H3 Part D. From DU.66246 the 6CA type of contact
breaker is used. The condensers no longer comprise
part ofthe contact breaker but are housed seperately
in a rubber covered pack below the front of the
fuel tank. Access to the condensers is gained by
H4
detaching the pack from the front tank mounting
bracket on the frame. removi ng the cover and
detaching the condensers individually from the
mou nti ng plate.
The best method of approach to a faulty ignition
system, is that of first checking the low tension
circuit for continuity as shown in H3 Part A, and
then following the procedure laid out in H3 Part B
to locate the fault(s).
Failure to locate a fault in the low tension circuit
indicates that the high tension circuit or sparking
plugs are faulty, and the procedure detailed in
H3 Part E must be followed. Before commencing
any of the follOWing tests, however. the contact
breaker and sparking plugs must be cleaned and
adjusted to eliminate this possible source of fault.
ClassicBike.biz
ELECTRICAL SYSTEM
H
Hl PART A. CHECKING THE LOW
TENSION CIRCUIT FOR CONTINUITY
To check whether there is a fault in the low tension
circuit and to locate its position, the following tests
should be carried out:-
Disconnect and remove the fuel tank (Section E1)
removing the white lead which connects the "SW"
terminals of the left and right ignition coils. Then.
with the wiring harness white lead connected to the
SW terminal of the left ignition coil only. turn the
ignition switch to the "IGN" position. Slowly
crank the engine and at the same time observe the
ammeter needle, which should fluctuate between
zero and a slight discharge, as the contacts open
and close respectively.
Disconnect the wiring harness white lead from the
left ignition coil and connect it to the S.W. terminal
of the right ignition coil and then repeat the test.
If the ammeter needle does not fluctuate in the
described way then a fault in the low tension circuit
is indicated.
First, examine the contact breaker contacts for
pitting. piling or presence of oxidation. oil or dirt
etc. Clean and ensure that the gap is set correctly
to 014 in.-016 in. (35-40 m.m.) as described in
Section B31.
Hl PART B. FAULT FINDING IN THE
LOW TENSION CIRCUIT
To trace a fault in the low tension wiring. turn the
ignition switch to "IGN" position and then crank
the engine until both sets of contacts are opened,
or alternatively. place a piece of insulating material
between both sets of contacts whilst the following
test is carried out.
For this test, it is assumed that the fuel tank is
removed and the wiring is fully connected as shown
in the appropriate wiring diagram. Section H17.
With the aid of a D.C. voltmeter and 2 test-prods
(Voltmeter 0-10 volts for 6 volt machines. and 0-15
volts for 12 volt electrical systems). make a point
to point check along the low tension circuit starting
at the battery and working right through to the
ignition coils. stage by stage. in the following
manner. referring to the relevant wiring diagram
in Section H17.
Note. On 12V machines it will be necessary to
disconnect the Zener Diode before the test is
carried out. To do this remove the white lead from
the Diode centre terminal.
(1) First. establish that the battery is earthed
correctly by connecting the volt meter across
the battery negative terminal and the machine
frame earth. No voltage reading indicates that
the red earthing lead is faulty (or the fuse
blown. where fitted). Also. a low reading
would indicate a poor battery earth connection
(2) Connect the voltmeter between the left
ignition coil S.W. terminal and earth and then
the right ignition coil S.W. terminal and earth.
No voltage reading indicates a breakdown
between the battery and the coil S.W. terminal.
or that the switch connections or ammeter
connections are faulty.
(3) Connect the voltmeter between both of the
ammeter terminals in turn and earth. No
reading on the "feed" side indicates that
either the ammeter is faulty or there is a bad
connection along the brown and blue lead
from the battery, and a reading on the
"battery" side only indicates a faulty ammeter.
(4) Connect the voltmeter between ignition switch
input terminal and earth. No reading indicates
that the brown and white lead has faulty
connections. Check for voltage at the brown/
white lead connections at rectifier, ammeter
and lighting switch terminals No's 2 and 10.
(5) Connect the voltmeter across ignition switch
output terminal and earth. No reading indicates
that the ignition switch is faulty and should be
replaced. Battery voltage reading at this point
but not at the ignition coil S.W. terminals
indicates that the white lead has become
"open circuit" or become disconnected.
(6) Disconnect the black/white, and black/yellow
leads from the C.B. terminals of each ignition
coil. Connect the voltmeter across the
C.B. terminal of the left coil and earth and then
the C.B. terminal of the right coil and earth.
No reading on the voltmeter in either case
indicates that thecoilprimary winding is faulty
and a replacement ignition coil should be fitted.
(7) With both sets of contacts open reconnect the
ignition coil leads and then connect the volt-
meter across both sets of c;ontacts in turn. No
reading in either case indicates that there is a
faulty connection or the internal insulation
has broken down in one of the condensers
(capacitors).
If a capacitor is suspected then a substitution
should be made and a re-test carried out.
(8) Finally. on machines with 12V electrical
systems. reconnect the Zener Diode white
lead and then connect the volt meter between
the Zener Diode centre terminal and earth
(With ignition "ON"). The volt meter should
read battery volts. If it does not the Zener
Diode is faulty and asubstitution should be made.
Refer to Section H6 (page H15) for the correct
procedure for testing a Zener Diode on the
machine. Ignition coil check procedure is given
in Section H3. part C (page H6).
H5
ClassicBike.biz
H
ELECTRICAL SYSTEM
Hl PART C. IGNITION COILS
The ignition coils consist of primary and secondary
windings wound concentrically about a laminated
soft iron core, the secondary winding being next to
the core. The primary winding usually consists of
some 300 turns of enamel covered wire and the
secondary some 17.000-26,000 turns of much finer
wire-also enamel covered. Each layer is paper
insulated from the next in both primary and secon-
dary windings.
To test the ignition coil on the machine, first ensure
that the low tension circuit is in order as described
in H3 Part A above then disconnect the high tension
leads from the left and right sparking plugs. Turn
the ignition switch to the "IGN" position and
crank the engine until the contacts (those with the
black/yellow lead from the ignition coil) for the
right cylinder are closed. Flick the contact breaker
lever open a number oftimes whilst the high tension
lead from the right ignition coil is held about 1
3
6 in.
away from the cylinder head. If the ignition coil is
in good condition a strong spark should be obtained.
if no spark occurs this indicates the ignition coil to
be faulty.
Fig. H3. Ignition coils in position on machine
Repeat this test for the left high tension lead and
coil by cranking the engine until the contacts with
the black/white lead from the left ignition coil are
closed.
H6
Before a fault can be attributed to an ignition coil It
must be ascertained that the high tension cables
are not cracked or showing signs of deterioration,
as this may often be the cause of mis-firing etc. It
should also be checked that the ignition points are
actually making good electrical contact when closed
and that the moving contact is insulated from earth
(ground) when open. It is advisable to remove the
ignition coils and test them by the method described
below.
BENCH TESTING AN IGNITION COIL
Connect the ignition coil into the circuit shown in
Fig. H4 and set the adjustable gap to 9 mm. for
MA12 types (12 volt) or 8 mm. for MA6 types
(6 volt). With the contact breaker running at
100 r.p.m. and the coil in good condition, not more
than 5 % missing should occur at the spark gap
over a period of 15 seconds. The primary winding
can be checked for short-circuit coils by connecting
an ohmeter across the low tension terminals.
The reading obtained should be within the figures
quoted below (at 20'C).
Coil
------
MA6
MA12
H.T.
Primary Resistance
Min. Max.
18 ohms. 24 ohms.
30 ohms. 34 ohms.
H<---++-- AUXILIARY ElECTRODE
~ _ G R E Y FIBRE
OR BAKELISED
FABRIC BLOCK
CONTACT BREAKER
Fig. H4. Ignition coil test rig
93
ClassicBike.biz
ELECTRICAL SYSTEM H
Hl PART D. CONTACT BREAKER
Faults occurring at the contact breaker are in the
main due to, incorrect adjustment of the contacts
or the efficiency being impaired by piling. pitting
or oxidation of the contacts due to oil etc. There-
fore, always ensure that the points are clean and
that the gap is adjusted to the correct working
clearance as described in Section B28
To test for a faulty condenser, first turn the ignition
switch to "IGN" position and then take voltage
readings across each set of contacts with the contacts
open. No reading indicates that the condenser
internal insulation has broken down. Should the
fault be due to a condenser having a reduction in
capacity, indicated by excessive arcing when in use,
and overheating of the contact faces, a check should
be made by substitution.
Particular attention is called to the periodic
lubrication procedure for the contact breaker which
is given in section A10. When lubricating the parts
ensure that no oil or grease gets onto the contacts.
B
I
BLACK 8. YELLOW
B
"
Fig. H5. Contact breaker and condenser assembly
Type 4CA
If it is felt that the contacts reqUire surface grinding
then the complete contact breaker unit should
be removed as described in Section B28 and the
moving contacts disconnected by unscrewing the
securing nuts from the condenser terminals.
Grinding is best achieved by using a fine carborun-
dum stone or very fine emery cloth, afterwards
wiping away any trace of dirt or metal dust with a
clean petrol (gasoline) moistened cloth. The con-
tact faces should be slightly domed to ensure point
contact. There is no need to remove the pitting
from the fixed contact. When re-fitting the moving
contacts do not forget to refit the insulating shields
to the condenser terminals and apply a smear of
grease to the C.B. cam and moving contact pivot
post. Lubricate the one felt pad.
Hl PART E CONTACT BREAKER FROM
DU.66246
Section H3 part D applies to the 6CA type contact
breaker except for removal of the contact points.
The moving contact points are removed by unscrew-
ing the nut which secures the low tension lead,
removing the lead and nylon bush. The spring and
contact point can be removed from the pivot spindle.
Repeat this procedure for the other contact point.
When reassembling. the nylon bush is fitted through
the low tension connection tab, and through the
spring location eye.
Pillar
Eccentric screw----,:.,p"(]])'
Secondary bra'ckel--ic
screw
Contact eccentric
adjusting screw
Contact Ilock'mg---'"
screw
Secondary bra,ck"t--
A
screw
Fig. H6. Contact breaker-Type 6CA
H3 PART F. CHECKING THE HIGH
TENSION CIRCUIT
If ignition failure or mis-firing occurs, and the fault
is not in the low tension circuit, then check the
ignition coils as described in Part C. If the coils
prove satisfactory, ensure that the high tension
cables are not the cause of the fault.
H7
ClassicBike.biz
H ELECTRICAL SYSTEM
If a good spark is available at the high tension cable.
then the sparking plug suppressor cap or the
sparking plug itself may be the cause of the fault.
Clean the sparking plug and adjust the electrodes to
the required setting as described in Section H3
below and then re-test the engine for running
performance. If the fault recurs then it is likely
the suppressor caps are faulty and these should be
renewed.
H3 PART G. CHECKING THE EMERGENCY
STARTING CIRCUIT-ONLY PRIOR TO
ENGI"IE NUMBER DU.24875
First, ensure that the contact breaker and sparking
plug gap settings are satisfactory and then remove
the contact breaker cover and place a small piece
of insulating card between each set of contacts.
Connect a D.C. voltmeter (015V) with the positive
lead to earth and negative lead to the moving
contact spring of the front set of contacts. A resistor
is not required for this test.
Turn the ignition switch to "IGN" pOSition. The
voltmeter should indicate battery voltage. Repeat
HB
the test with the voltmeter negative lead connected
to the rear moving contact spring.
Disconnect the green/yellow (green/black on 12V
models) lead from the alternator (underneath the
engine) and connect the voltmeter positive to
green/yellow harness lead (green/black on 12V)
and negative lead to frame. Turn the ignition
switch to "EMG position. The voltmeter should
indicate battery voltage. If it does not the green/
yellow lead (green/black on 12V) to No. 17 ignition
switch terminal. and black/white lead connecting
ignition coil C.B. (+) terminal to Ignition switch
terminal No. 15 should be checked. Reconnect
alternator lead.
Finally, disconnect the battery. and then connect an
A.C. voltmeter (0-15V) between the front moving
contact spring and frame. With ignition switch
in "EMG" position. (both contacts still insulated
with card) attempt to kickstart the engine. The
A.C. voltmeter should deflect to about 7 to 10 volts.
If it does not. the alternator should be checked as
shown in Section H5 Part B.
ClassicBike.biz
ELECTRICAL SYSTEM H
SECTION H4
SPARKING PLUGS
It is recommended that the sparking plugs be
inspected. cleaned and tested every 3,000 miles
(4,800 k.m.) and new ones fitted every 12,000
miles (20,000 k.m.).
To remove the sparking plugs a box spanner (:! in.
(195 m.m.) across fiats) should be used and if any
difficulty is encountered a small amount of pene-
trating oil (see lubrication chart Section A2)
should be placed at the base of the sparking plug
and time allowed for penetration. When removing
the sparking plugs identify each plug with the
cylinder from which it was removed so that any
faults revealed on examination can be traced back
to the cylinder concerned.
Due to certain features of engine design the sparking
plugs will probably show slightly differing deposits
and colouring characteristics. For this purpose it is
recommended that any adjustments to carburation
etc., which may be carried out to gain the required
colour characteristics should always be referred
to the left cylinder.
Examine both plugs for signs of oil fouling. This
will be indicated by a wet, shiny, black deposit on the
central insulator. This is caused by excessive oil in
the combustion chamber during combustion and
indicates that the piston rings or cylinder bores are
worn.
Next examine the plugs for signs of petrol (gaso-
line) fouling. This is indicated by a dry, sooty,
black deposit which is usually caused by over-rich
carburation. although ignition system defects such
as a discharged battery, faulty contact breaker. coil
or condenser defects. or a broken or worn out cable
may be additional causes. To rectify this type of
fault the above mentioned items should be checked
with special attention given to carburation system.
Again, the left plug should be used as the indicator.
The right plug will almost always have a darker
characteristic.
Over-heating of the sparking plug electrodes is
indicated by severely eroded electrodes and a white,
burned or blistered insulator. This type of fault
is usually caused by weak carburation. although
plugs which have been operating whilst not being
screwed down sufficiently can easily become over-
heated due to heat that is normally dissipated
through to the cylinder head not having an adequate
conducting path. Over-heating is normally sympto-
mised by pre-ignition, short plug life, and "pinking"
which can ultimately result in piston crown failure.
Unecessary damage can result from over-tightening
the plugs and to achieve a good seal between the
plug and cylinder head a torque wrench should be
used to tighten the plugs to the figure quoted in
"General Data".
A
c
D
Fig. H7. Sparking plug diagnosis
1
_,
,.
A plug of the correct grade will bear a light fiaky
deposit on the outer rim and earth electrode. and
these and the base of the insulator will be light
chocolate brown in colour. A correct choice of
plug is marked A. B shows a plug which appears
bleached, with a deposit like Cigarette ash; this is
too 'hot-running' for the performance of the engine
and a cooler-running type should be substituted.
A plug which has been running too 'cold' and has
not reached the self-cleaning temperature is shown
at C. This has oil on the base of the insulator and
electrodes, and should be replaced by a plug that
will burn off deposits and remove the possibility of
a short-circuit. The plug marked D is heavily
sooted, indicating that the mixture has been too
rich, and a further carburation check should be
made. At illustration E is seen a plug which is
completely worn out and badly in need of replace-
ment.
To clean the plugs it is preferable to make use of a
properly designed proprietary plug cleaner. The
maker's instructions for using the cleaner should
be followed carefully.
H9
ClassicBike.biz
H ELECTRICAL SYSTEM
When the plugs have been carefully cleaned,
examine the central insulators for cracking and the
centre electrode for excessive wear. In such cases
the plugs have completed their useful life and new
ones should be fitted.
Finally, before re-fitting the sparking plugs the
electrodes should be adjusted to the correct gap
setting of 020 in. (5 mm.). Before refitting spark-
ing plugs the threads should be cleaned by means
of a wire brush and a minute amount of graphite
grease smeared onto the threads. This will prevent
any pOSSibility of thread seizure occurring.
If the ignition timing and carburation settings are
correct and the plugs have been correctly fitted,
but over-heating still occurs then it is possible that
carburation is being adversely affected by an air
leak between the carburetter, manifold and the
cylinder head. This possibility must be checked
thorough Iy before taki ng any fu rther action. When
it is certain that none of the above mentioned faults
are the cause of over-heating then the plug type and
grade should be considered.
Normally the type of plugs quoted in "General
Data" are satisfactory for general use ofthe machine.
but in special isolated cases, conditions may demand
a plug of a different heat range. Advice is readily
available to solve these problems from the plug
manufacturer who should be consulted.
Note.-If the machine is of the type fitted with an
air filter or cleaner and this has been removed it
will affect the carburation of the machine and
hence may adversely affect the grade of sparking
plugs fitted.
SECTION HS
CHARGING SYSTEM
DESCRIPTION
The charging current is supplied by the alternator.
but due to the characteristics of alternating current
the battery cannot be charged direct from the
alternator. To convert the alternating current to
direct current a full wave bridge rectifier is o n ~
nected into the circuit. The alternator gives full
output, all the alternator coils being permanently
connected across the rectifier. For this reason
latest alternators have only 2 output leads.
Excessive charge is absorbed by the Zener Diode
which is connected across the battery. On earlier
machines the Zener Diode may be connected to
the battery, through the ignition switch. Always
ensure that the ignition switch is in the "OFF"
position whilst the machine is not in use,to prevent
overheating of the ignition coils, and discharging
the battery.
On machines prior to engine number DU.24875
all the alternator coils are not permanently con-
nected. The varying outputs are achieved by inter-
connecting the generating coils and switch terminals
as shown in the diagram in Figs. H9 and H10.
With the lighting switch in "OFF" position the
coils A and B are short circuited and flux induced
interacts with the rotor flux maintaining minimum
output. With the switch in PILOT position the
H10
coils A and B are open circuited and the flux
interaction is thereby reduced causing coil C to give
increased "medium" out-put. With the switch in
HEAD position the coils A, Band C are connected
in parallel, giving maximum output.
with a 12 volt electrical system and Zener Diode
charge control, the alternator leads are connected
differently in the low out-put connection (l.e.
lighting switch in "OFF" position). The alternator
gives "medium" out-put for the lighting switch in
both the "OFF" and PILOT positions, the four
coils Band C being permanently connected across
the rectifier. Switching to "HEAD" position
connects the two remaining coils, A. (See Fig. H9).
Excessive charge is absorbed by the Zener Diode
which is connected across the battery.
To locate a fault in the charging circuit, first test the
alternator as described in H5 Part B. If the alter-
nator is satisfactory, the fault must lie in the
charging circuit, hence the rectifier must be checked
as given in Section H5 Part C (page H11) and then
the wiring and connections as shown in Section HS
Part D (page H13).
In the case of a machine prior to engine number
DU.24875, first check the charging rate in the
three switch positions as shown above.
ClassicBike.biz
OFFo
TO IGN. COILS & oON
IGN. WARNING LIGHT
ELECTRICAL SYSTEM
ALTERNATOR
A
IGNITION
SWITCH
aFFo
PlLOTo
HEADo
ZENER
DIODE
C
LIGHT
SWITCH
RECTIFIER
12v.
258
Fig. HR. Schematic diagram of 12 volt charging circuit with single charge rate and Zener Diode
All models coil ignition from DU.24B7S
EMGo
Gis
QFFO "-
IGN IGNITION
SWITCH
BLUE
ALTERNATOR
s
GIB
G!Y
OOf-F
LIGHT
SWITCH
o PILOT
HEAD
RECTIFIER
RED
ZENER DIODE
~ ~
BATTERY =
{2-6V in series} 139
Fig. H9. Schematic iIIustl"ation of 12 volt charging circuit (6T up to engine No. DU.24874)
ALTERNATOR
GIw
G/B
RED
EMGO
G/W
OFF 0 \
G!Y
BR/W
-
IGNITION SWITCH
IGN
6V
OFF
J l ~
BLUE
\ 0 PILOT
LIGHT SWITCH
G/B
BATTERY _
HEAD
13tJ
Fig. H10. Schematic illustration of 6 volt charging circuit
6T up to engine No. DU.S824 TR6 and T120 up to engine No. DU.24874
H
H11
ClassicBike.biz
H
ELECTRICAL SYSTEM
H5 PART A. CHECKING THE D.C. INPUT
TO BATTERY
For this test the battery must be in good condition
and a good state of charge, therefore before
conducting the test ensure that the battery is up
to the required standard, or alternatively fit a
good replacement battery.
Connect D.C. ammeter (0-15 amp.) in series
between the battery main lead (brown/blue) and
battery negative terminal and then start the engine
and run it at approximately 3,000 r.p.m. (equivalent
to 45 m.p.h. in top gear).
Note.-Ensure that the ammeter is well insulated
from the surrounding earth points otherwise a
short circuit may occur.
Operate the lighting switch and observe the
ammeter readings, for each position of the switch.
The observed figures should not be less than those
tabulated in Fig. H20 for the particular model. If
the readings are equal to or higher than those given,
then the alternator and charging circuit are satis-
factory. If the readings are lower than those quoted,
then the alternator must be tested as described in
Part B below.
H5 PART B. CHECKING THE
ALTERNATOR OUTPUT
Disconnect the three alternator output cables
underneath the engine and run the engine at 3,000
r.p.m. (equivalent to 45 m.p.h. in top gear).
Connect an A.C. voltmeter (0-15 volts) with
1 ohm load resistor in parallel with each of the
alternator leads in turn as shown in the table,
Fig. H20. and observe the voltmeter readings. A
suitable 1 ohm load resistor can be made from a
piece of nichrome wire as shown in Section H4
Part E.
From the results obtained. the following deductions
can be made:-
(i) If the readings are all equal to or higher than
those quoted for the particular model then
the alternator is satisfactory.
(ii) A low reading on any group of coils indicates
either that the leads concerned are chafed or
damaged due to rubbing on the chains or that
some turns of the coils are short circuited.
(iii) Low readings for all parts of the test indicates
either that the green/white lead has become
chafed or damaged due to rubbing on the
chain(s) or that the rotor has become partially
Hll
demagnetised. If the latter case applies, check
that this has not been caused by a faulty
rectifier or that the battery is of incorrect
polarity, and only then fit a new rotor.
(iv) A zero reading for any group of coils indicates
that a coil has become disconnected, is open
circuit, or is earthed.
(v) A reading obtained between anyone lead and
earth indicates that coil windings or con-
nections have become earthed.
If any of the above mentioned faults occur, always
check the stator leads for possible chain damage
before attempting repairs or renewing the stator.
It is beyond the scope of this manual to give instruc-
tion for the repair of faulty stator windings. How-
ever, the winding specification is given in the table.
Fig. H20 for those obliged to attempt repair work.
H5 PART C. RECTIFIER MAINTENANCE
AND TESTING
The silicon bridge rectifier requires no maintenance
beyond checking that the connections are clean and
tight. and that the nut securing the rectifier to the
frame is tight. It should always be kept clean and
dry to ensure good cooling. and spilt oil washed
off immediately with hot water.
Note.-The nuts clamping the rectifier plates
together must not be disturbed or slackened in
any way.
When tightening the rectifier securing nut, hold
the spanners as shown in Fig. H11. for if the plates
are twisted, the internal connections will be broken.
Note that the circles marked on the fixing bolt and
nut indicate that the thread form is * in. U.N.F.
Fig. H11. Refitting the rectifier
ClassicBike.biz
ELECTRICAL SYSTEM H
TESTING THE RECTIFIER
For test purposes disregard the end earth
(ground) terminal on latest rectifiers
To test the rectifier, first disconnect the brown!
white lead from the rectifier centre terminal and
insulate the end of the lead to prevent any possibility
ofa short circuit occurring. and then connect a D.C.
voltmeter (with 1 ohm load resistor in parallel)
between the rectifier centre terminal and earth.
Disconnect the alternator greenJyeliow lead (greenJ
black on 12V) and reconnect to rectifier greenJ
black terminal (greenJyeliow on 12V) by means of
a jumper lead.
Note. Voltmeter positive terminal to frame
earth (ground) and negative terminal to centre
terminal on rectifier.
Ensure that all the temporary connections are well
insulated to prevent a short circuit occurring then
turn the ignition switch to "IGN" position and
start the engine.
With the engine running at approximately 3,000
r.p.m. (approximately 45 m.p.h. in top gear)
observe the voltmeter readings. The reading o b ~
tained should be at least 75V minimum on 12V and
6V machines.
(I) If the reading is equal to or slightly greater
than that quoted, then the rectifier elements
in the forward direction are satisfactory.
(ii) If the reading is excessively higher than the
figures given, then check the rectifier earthing
bolt connection. If the connection is good
then a replacement rectifier should be fitted.
(iii) If the reading is lower than the figures
quoted or zero readings are obtained, then the
rectifier or the charging circuit wiring is
faulty and the rectifier should be disconnected
and bench tested so that the fault can be
located.
Note that all of the above conclusions assume that
the alternator A.C. output figures were satis-
factory. Any fault at the alternator will, of course,
reflect on the rectifier test results. Similarly any
fault in the charging circuit wiring may indicate
that the rectifier is faulty. The best method of
locating a fault is to disconnect the rectifier and
bench-test it as shown below:
BENCH TESTING THE RECTIFIER
For this test the rectifier should be disconnected
and removed. Before removing the rectifier,
disconnect the leads from the battery terminals to
avoid the possibility of a short circuit occurring.
Connect the rectifier to a 12 volt battery and 10hm
load resistor, and then connect the D.C. volt-
meter in the V2 position, as shown in Fig. H12.
Note the battery voltage (should be 12V) and then
connect the voltmeter in V1 pOSition whilst the
following tests are conducted.
;j,
I
~ .
0
0
>
~
~
~
~
~
m
i
~
I
Ul
I
II
I
Ii
.. J
VVV'0NV'-
1 OHM RESISTOR
Fig. Hll. Bench testing the rectifier
A voltmeter in position V1 will measure the volt
drop across the rectifier plate. In position V2 it
will measure the supply voltage to check that it is
the recommended 12 volts on load.
1 l 3
Fig. H13. Rectifier-showing terminal connections for
bench tests 1 and 2
H13
ClassicBike.biz
H ELECTRICAL SYSTEM
TEST 1 CHECKING FORWARD RESISTANCE
+ ~
,
, '
---(
)..'
... "4 - JI
---{ ..
2 ) t ~ . . . ,/
.L-.,Ii;. ""-
" ,>.-'
, , .
y
:3
TEST2 CHECKING BACK LEAKAGE
Rectifier test sequence for checking forward resistance and back leakage
Test 1. With the test leads. make the following
connectings but keep the testing time as short as
possible to avoid overheating the rectifier cell:
(a) 1 and 2, (b) 1 and 4, (c) 3 and 4, (d) 3 and 2. Each
reading should not be greater than 25 volts with the
battery polarity as shown.
Test 2. Reverse the leads or battery polarity and
repeat Test 1. The readings obtained should not be
more than 15 volts below battery voltage (V,J
(i.e. 105 volts minimum.)
If the readings obtained are not within the figures
given, then the rectifier internal connections are
shorting or aged and the rectifier should be
renewed.
HS PART D_ CHECKING THE CHARGING
CIRCUIT FOR CONTINUITY
On later 12 volt machines the electrical circuit is so
arranged that all six alternator coils are connected in
parallel so that the full alternator output is available
irrespective of the lighting switch position. This
also makes an emergency start system unnecessary
and it is therefore poss; ble to use a si m plified
wiring circuit.
First check that there is voltage at the battery and
that it is correctly connected into the circuit
+ve earth (ground). Ensure that the fuse has not
blown.
(i) First, check that there is voltage at the rectifier
centre terminal by connecting a D.C. volt-
meter, with 1 ohm load resistor in parallel,
between the rectifier centre terminal (not the
H14
end terminal on latest rectifiers) and earth
(remember (+ve)positive earth (ground)).
The voltmeter should read battery volts. If it
does not, disconnect the alternator leads
(green/black, green/white and green/yellow)
at the snap connectors under the engine unit.
(a) Fit a jumper lead across the brown/white and
green/yellow connections at the rectifier,
and check the voltage at the snap connector.
This test will indicate whether the harness
alternator lead is open circuit.
(b) Repeat this test at the rectifier for the white /
green lead.
(2) If no voltage is present at the rectifier central
terminal (brown/white), check the voltage at
the ammeter terminal. If satisfactory, it
indicates that the brown/white wire is open
circuit. If not, the ammeter is open circuit.
(3) If no voltage is present at either ammeter
terminal, then the brown/blue wire from the
battery (-ve) is open circuit.
after checki ng for battery voltage at the rectifier
centre terminal, proceed as follows:
(ii) This test does not apply to machines with 12 volt
systems. Connect the green/yellow lead from
the wiring harness (underneath the engine)
to the rectifier centre terminal lead (brown/
white), by means of a jumper lead, and turn
the ignition switch to "IGN" position.
ClassicBike.biz
ELECTRICAL SYSTEM H
Connect a D.C. voltmeter with load resistor
in parallel between the green/white lead at
the rectifier and earth (frame). With the
lighting switch at "OFF" position, the
voltmeter should read battery volts. If it
does not the leads to ignition switch ter-
minals 16 and 18 should be checked and also
the leads to lighting switch terminals 4 and S
must be checked.
(iii) Connect the green/yellow lead (green/black
lead for 12 volt system) from the wiring
harness (underneath the engine) to the
rectifier centre terminal. by means of a
jumper lead, as in test (ii). Turn the ignition
switch to "IGN" position and the lighting
switch to HEAD position, and connect a D.C.
voltmeter (with 1 ohm resistor in parallel)
between green/black lead (green/yellow lead
on 12 volt models) at rectifier and earth. The
voltmeter should read battery voltage. If it
does not, the leads to ignition switch terminals
16 and 17 should be checked and the leads to
the lighting switch terminals Sand 7 should
also be checked. With the lighting switch in
'Pilot' position no reading should be obtained
between green/black (green/yellow on 12
volt models) and earth or green Iwhite and
earth at the rectifier.
HS PART E, CONSTRUCTING A ONE
OHM LOAD RESISTOR
The resistor used in the following tests must be
accurate and constructed so that it will not over-
heat otherwise the correct values of current or
voltage will not be obtained.
A suitable resistor can be made from 4 yards
(3j metres) of 18 S.W.G. (048 in. (i.e. 12 m.m.)
dia.) NICHROME wire by bending it into two
equal parts and calibrating it as follows:-
(1) Fix a heavy gauge flexible lead to the folded
end of the wire and connect this lead to the
positive terminal of a 6 volt battery.
(2) Connect a D.C. voltmeter (0-10V) across the
battery terminals and an ammeter (0-10 amp)
between the battery negative terminal and
the free ends of the wire resistance, using a
crocodile clip to make the connection.
(3) Move the clip along the wires, making contact
with both wires until the ammeter reading is
numerically equal to the number of volts
shown in the voltmeter. The resistance is then
1 ohm. Cut the wire at this point, twist the
the two ends together and wind the wire on
an asbestos former approximately 2 inches
(5 em.) dia. so that each turn does not contact
the one next to it.
H1S
ClassicBike.biz
H ELECTRICAL SYSTEM
SECTION H6
ZENER DIODE CHARGE CONTROL (12 VOLT MACHINES ONLY)
DESCRIPTION
The Zener Diode output regulating system uses
all the coils of the 6-coil alternator connected
permanently across the rectifier. provides auto-
matic control of the charging current. It will only
operate successfully on a 12 volt system where it is
connected in parallel with the battery as shown in
the wiring diagram (Section H19 Fig. H33). The
Diode may be conneccd through the ignition
switch or direct to the centre terminal of the
rectifier.
TERM I
BLADE
EARTHING
:1>--- STU D 143
Fig. H15. Zener Diode
Assuming the battery is in a low state of charge its
terminal voltage (the same voltage is across the
Diode) will also be low, th.refore the maximum
charging current will flow into the battery from the
alternator. At first none of the current is by-passed
by the Diode because of it being non-conducting
H16
due to the low battery terminal volts. However.
as the battery is qUickly restored to a full state of
charge. the system voltage rises until at 14 volts
the Zener Diode becomes partially conducting,
thereby providing an alternative path for a small
part of the charging current. Small increases In
battery voltage result in large increases in Zener
conductivity until, at approximately 15 volts about
5 amperes of the alternator output is by-passing the
battery. The battery will continue to receive only
a portion of the alternator output as long as the
system voltage is relatively high.
Depression of the system voltage. due to the use of
head lamp or other lighting equipment, causes the
Zener Diode current to decrease and the balance to
be diverted and consumed by the component in
use.
If the electrical loading is sufficient to cause the
'ystem voltage to fall to 14 volts, the Zener Diode
will revert to a high resistance state of non-
conductivity and the full generated output will go
to meet the demands of the battery.
Provided an adequate heat sink is employed, the
Zener Diode is able to absorb the full output of the
alternator. Machines previously employing 6 volt
systems and subsequently converted to 12 volts
retain some form of charge control through
the lighting switch. This is achieved by perma-
nently connecting four charging coils across
the rectifier (green/white - green/yellow) and
bringing in the other two coils (green/black) in the
lighting switch head lamp position (Fig. Ha).
ClassicBike.biz
ELECTRICAL SYSTEM H
MAINTENANCE
The Zener Diode is mounted on an aluminium heat
sink. Providing the Diode and the heat sink are kept
clean, and provided with an adequate airflow. to
ensure maximum efficiency. and provided a firm flat
"metal to metal" contact is mantained between the
base of the Diode and the surface of the heat sink,
to ensure adequate heat flow, no maintenance will
be necessary.
ZENER DIODE-
CHARGING REGULATOR
TEST PROCEDURE
(Procedure for Testing on the Machine)
The test procedure given below can be used when
It is required to check the performance of the
Zener Diode type ZD715 whilst it is In position
on the machine.
Good quality moving coil meters should be used
when testing. The voltmeter should have a scale
0-18, and the ammeter 0-5 amps min. The test
procedure Is as follows:-
(A) Disconnect the cable from the zener diode and
connect ammeter (in series) between the diode
Lucar terminal and cable previously discon-
nected. The ammeter red or positive lead
must connect to the diode Lucar terminal.
(B) Connect voltmeter across zener diode and
heat sink. The red or positive lead must con-
nect to the heat sink which is earthed to the
frame of the machine by its fixing bolts and a
separate earth lead. The black lead connects
ta the zener Lucar terminal.
(C) Start the engine, ensure that all lights are off,
and gradually increase engine speed while at
the same time observing both meters:-
<I> the series connected ammeter must indicate
zero amps, up to 1275 volts, which will be
indicated on the shunt connected voltmeter
as engine speed is slowly increased.
(ii) increase engine speed still further, until zener
current indicated on ammeter is 20 amp. At
this value the zener voltage should be 135
volts to 153 volts.
TEST CONCLUSIONS:-
If the ammeter in test (i) registers any current at all
before the voltmeter indicates 130 volts, then a
replacement zener diode must be fitted.
If test (i) is satisfactory but in test (ii) a higher
voltage tnan tnat stated is registered on tne volt-
meter, before tne ammeter indicates 20 amp, tnen
a replacement zener diode must be fitted.
H17
ClassicBike.biz
H ELECTRICAL SYSTEM
SECTION H7
ZENER DIODE LOCATION
FROM DU.66246
The Zener diode is mounted below the head lamp.
being bolted to the fork middle lug. The aluminium
o
heatsink is finned to assist cooling and is secured to
the fork by a bracket and bolts. See Fig. below.
Fig. H16. Finned heatsink (from DU.66246)
To remove diode only, disconnect the brown/white
double' 'Lucar" connector from the diode. Remove
the black plastic plug from the heat sink (See Fig. H16)
and unscrew the "nyloe" nut which secures the
diode. When refitting. the diode nut must be
tightened with extreme care.
To remove the finned heat sink, remove the front
bolt from the retaining bracket. A double red
earth (ground) wire is attached at this point.
DO NOT ATTACH THE EARTH
(GROUND) LEADS BETWEEN THE DIODE
BODY AND HEATSINK
The Zener Diode is fitted to a heat sink which is
located behind the left hand switch panel.
To enable the Zener Diode to be removed from its
heat sink, the left hand switch panel must first be
removed as described in Section E3. Disconnect
and remove the batteries so that the two bolts,
nuts and washers securing the heat sink can be
removed. The Zener securing nut and earthing
strap should be carefully removed from beneath
the heat sink and the Zener lifted clear after discon-
necting the Lucar connector securing the feed cable
to the top of the Zener.
NOTE: When refitting the Zener to the heat sink,
it is essential that the earthing strap is refitted
H18
correctly. i.e., between the heat sink and Zener
securing nut. It must NOT be placed between the
Zener body and heat sink as this could cause a
heat build up possibly resulting in a Zener Diode
failure.
Fig. H17. Zener diode location (before DU.66246)
Before DU.24875. The heatsink on 6T machines
was fitted to the front petrol tank mounting bolts
but removal and refitting of the diode is as for later
machines.
ClassicBike.biz
ELECTRICAL SYSTEM H
SECTION H8
A.C. IGNITION (E.T.) AND A.C. LIGHTING SYSTEMS
250T
BROWN
250T
CONTACT
BREAKER
STOPLIGHT
gaT gaT
alv
COIL CONDENSER COIL CONDENSER
3ET COIL
H.T. LEAD
l.CVllNDER
H.T. LEAD
R.CYLINDER
CUT OUT SWITC H
145
FiB. H18. Schematic illustration of A.C. ignition
(E.T.) system
DESCRIPTION
The A.C. magneto (energy transfer) system con-
sists of two 3 E.T. ignition coils, a contact breaker
and an alternator specially wound for A.C. ignition
and lighting. There are five leads from the alterna-
tor, two for ignition purposes and three for direct
lighting purposes. The circuit diagram, Fig. H35 in
Section H19 illustrates the stator coil connections.
The main features of the A.C. ignition system for
twin cylinder machines is that the ignition coil and
contact breaker points are connected in parallel.
In practice this means that when the contacts are
closed the current can flow directly to earth.
'When one set of contacts open, the current has to
pass through the ignition coil primary winding to
earth through the second set of contacts which are
arranged to be closed at the same instant. From
this it can be seen that the availability of a spark at
either cylinder is dependent upon both contacts
being clean and adjusted correctly (see Fig. H18).
Another feature is that the E.T. system operates on
a rising current in the ignition coil primary winding
and not falling primary current as in the con-
ventional coil ignition system.
H8 PART A. A.C_ IGNITION
The accurate and efficient working of the A.C.
ignition system is dependent not only upon the
piston/spark relationship that is involved but also
the rotor/stator relationship at the instant of
ignition. The stator is fixed to the left crankcase
and requires no maintenance other than to check
that the leads are not rubbing on either of the chains.
The rotor is located on the crankshaft by means of
a dowel fitted to the engine sprocket. When the
rotor is removed care should be taken to refit it
in the appropriate position with the rotor hole
located as shown in the tabel below, in accordance
with ignition timing requirements.
Dowel Ignition Timing Dowel
Location Full-Advanced Remarks
"S" 3r B.T.C. Standard
"R" 41
0
B.T.C. Racing
"M" 39" B.T.C. "Mid" position
It is beyond the scope of this Manual to advise on
a deviation from the standard setting. as so many
factors are involved. If it is required to alter the
settings from standard. then advice should be
sought from a local Triumph Dealer or the Triumph
Engineering Co. Ltd .. Service Department.
The 3 E.T. coil, condensers (capacitors), and high
tension leads must be kept clean and free from dirt
or water. Also. it is important that the sparking
plug is maintained at the correct gap setting and
that the centre electrode is kept clean.
H19
ClassicBike.biz
H ELECTRICAL SYSTEM
Fl._ Ht9. A.C. i.nitlon colis fitted on machine
Both sets of contact breaker contacts must be kept
clean and adjusted correctly to the gap setting
given in General Data. A fault at either set of
contacts will adversely affect the ignition spark at
BOTH cylinders.
H8 PART B. TESTING THE A.C.
IGNITION SYSTEM
First, ensure that the timing. contact breaker and
plug gaps are satisfactory. and then disconnect both
H.T. leads and check that a spark is available by
holding each of the cables about -h inches (4 mm.)
from the cylinder head in turn and operate the
kickstarter. A good spark should be produced. If
it is not. then the 3 E.T. coil and alternator ignition
supply are suspect.
As it is not possible to test the 3 E.T. coils accurately
on the machine. the following test procedure
should be adopted.
Two 6 volt external batteries are used for the next
two tests. in conjunction with the A.C. ignition
coils on the machine.
H20
A.C. ignition coils are not designed to run under
such conditions. overheating occurring in the
primary windings.
Each test should be undertaken in as short a
time as possible, and the batteries connected
in circuit only when actually necessary to run
the test.
(1) Disconnect the five alternator leads under the
engine.
(2) Unplug the black/yellow lead from the con-
denser at the right hand side coil (under the
petrol (gasolene) tank.
(3) Connect the black/yellow lead to the positive
(+ve) terminal of a (6V) test battery.
(4) Connect the negative (-ve) battery lead to
the condenser terminal.
(5) Unplug the black/white lead from the con-
denser at the left hand side coil (under the
petrol (gasolene) tank).
(6) Connect the black/white lead to the positive
(+ve) terminal of a second (6V) test battery.
(7) Connect the negative (-ve) terminal of the
second test battery to the left hand condenser
terminal.
(8) Remove the sparking plug wire from each plug
in turn and with battery wires connected, open
and close the CO.11act breaker points. If the
coils and condensers are satisfactory. a good
spark will jump from the plug lead to earth
(ground).
(9) If a poor spark (or no spark) is noted. check
all wiring connections. and repeat (8) above.
If the system still does not spark. instal new
condensers and repeat (8). If still there is no
spark. check the ignition coils by substitution.
ClassicBike.biz
ELECTRICAL SYSTEM H
H8 PART C. CHECKING THE
ALTERNATOR OUTPUT (A.C. Ignition
Models)
To facilitate a check to be made on the alternator
output, a separate ignition circuit must be used as
given in Section H8 Part B above. so that the engine
can be run at 3,000 r.p.m. (approximately 45 m.p.h.
in top gear).
Pay careful regard to the warning given in the
previous section (HB part B) concerning the possible
overheating of the A.C. ignition coil primary
windings.
The preferred alternative method is to use two
MA6 ignition coils, bolted together, with the
machines C.B. leads, BLACK/WHITE, BLACK/
YELLOW connected to the appropriate C.B.
terminals on the test ignition coils. The test coil
S.W. terminals are linked together and fed to a test
battery (-ve) negative terminal and the battery
(+ve) positive connected to the ignition coils cases.
A jumper lead is also required between battery
(+ve) positive, and motorcycle frame earth
(ground). The H.T. leads are connected to the
appropriate sparking plugs.
With all five alternator leads disconnected under
the engine start up the engine and run at 3,000 r.p.m.
(equivalent to approximately 45 m.p.h. in top gear).
Connect an A.C. voltmeter (0-10V) with a 1 ohm
resistor in parallel between the pairs of alternator
leads given in table, Fig. H20 Section H9.
(i) If the readings are equal to or higher than the
figures quoted for the particular model, then
the alternator is satisfactory.
(ii) A low reading on any group of coils indicates
either that the leads concerned are chafed
through or damaged due to rubbing on the
chains or that some of the coil turns are short
circuited.
(iii) Low readings from all parts of the test indio
cates a partially demagnetized rotor. In this
case the rotor must be renewed.
(iv) A zero reading for any group of coils indicates
that a coil has become disconnected and is
open circuit, in which case the stator should
be replaced.
(v) A reading obtained between anyone stator
lead and earth (ground) ,ndicates that some
coil turns have become earthed (grounded)
to the engine. In this case, brush the stator
with paraffin (kerosene) or petrol (gasoline).
DO NOT LEAVE TO SOAK. Retest on the
machine. If still faulty, replace the stator.
If any fault does occur always check the stator leads
for possible chain damage before attempting repair
or renewing the stator. It is beyond the scope of
this manual to give instruction for repair of faulty
stator windings. However the winding specification
is given in table, Fig. 1-119 to provide the required
information for local repair work, should a correct
replacement stator not be immediately available.
H8 PART D DIRECT LIGHTING SYSTEM
The electrical power for the direct lighting system
is supplied by three of the five alternator leads,
namely the red, brown and brown/blue. The leads
are connected as shown in "the wiring diagram
(Fig. H35 in Section H19). In order that no one pair
of coils is overloaded, the electrical loads are
connected as shown and no deviation from the
standard arrangement shown should be made.
An apparent loss or reduction of power at any of the
lights may well be due to a high resistance caused
by a loose or faulty connection. In the event of a
fault occuring, always check the wiring connections,
giving particular attention to the red earth (ground)
lead from the alternator and headlamp. Note that a
short circuit in the brown stop lamp lead will
result in the ignition system failing. hence the stop
lamp switch connections should be always kept
clean and dry.
In the event of a fault occuring which cannot be
traced to the circuit connections the alternator
should be checked as described in Section HB,
Part C above.
H21
ClassicBike.biz
H
.
MODELS
T120, TR6, 6T
T120R, TR6R
ELECTRICAL SYSTEM
SECTION H9
ALTERNATOR AND STATOR DETAILS-
SPECIFICATIONS AND OUTPUT FIGURES
Machines subsequent to DU.24875
System Ignition Alternator
voltage type type
12 V. Coil RM.19
T120n, TR6 c. 6 V. A.C.IGN RM.19
Fig. H21. Electrical system details
Alternator Output
Stator
No.
47162
After DU.58565
47204
47188
D.C. input to battery minimum A.C. volts @ Stator coil details
amp. @ 3,000 r.p.m.
Stator System
number voltage Off Pilot Head
47162
15 10
12 V.
65t 43t
47188 6 V. Not applicable
Coi I Ignition Machines
and Green/Black
and Green/Yellow
10
20t
A
40
50
-
{
Green/Black }
and Green/Yellow connected
3,000 r.p.m.
B
65
15
-
C No of Turns
coils per coil
85 6 140
2 250
35 2 98
1 98
1 98
85 6 140
Zener in Circuit
tZener disconnected
From DU.58565 2 stator leads only are used i.e. Green/White and Green/Yellow.
A.C. Ignition Machines
Hll
and Brown/Blue
and Black/White
and Brown
Fig. H20. Alternator-minimum output and stator details
S.W.G.
22
25
20
20
21
22
}GN.
}UGHTS
ClassicBike.biz
ELECTRICAL SYSTEM
ALTERNATOR AND STATOR DETAILS-
SPECIFICATIONS AND OUTPUT FIGURES
Before engine number DU.24875
System Ignition Alternator
MODELS voltage type type
6T 12 V.
Coil RM.19
TR6SR. T120R. T120C. 6T.U.S.A 6 V.
6T. TR6. T120 6 V. Coil RM.19
6T (Police) 6 V. Coil RM.19/20
TR6SC. T120TT Special 6 V. A.c. IGN RM.19
Fig. H13. Electrical system details
Alternator Output
Stator
No.
47162
47164
47167
47188
D.C. input to battery minimum A.C. volts @
Stator coil details
amp. @ 3.000 r.p.m. 3.000 r.p.m.
Stator System
H
number voltage
Off Pilot Head A B C
No of Turns
S.W.G.
coils per coil
(Main beam)
6 V. 275 20
47162 20 21
12 V.
48j 38j
47164 6 V. 2-7 09
47167 6 V. 66: 66:
Coil Ignition Machines
and Green/Black
and Green/Yellow
20
15
18j
1-6
13-6:
40
45
77
50
. {Green/Black }
and Green/Yellow connected
A.C. Ignition Machines
A Red and Brown/Blue
B Black/Yellow and Black/White
C Black/Yellow and Brown
65 85 6 140 22
70 95 6 122 21
11-6 13-2 6 74 19
2 250 25
15 35 2 88 20
1 88 20
1 98 21
* Zener in Circuit
t Zener disconnected
tWith Boost Switch in Circuit
Flg. H12. Alternator-Minimum output and stator details
H23
ClassicBike.biz
H ELECTRICAL SYSTEM
SECTION HIO
ELECTRIC HORN
DESCRIPTION
The horn is of a high frequency single note type and
is operated by direct current from the battery.
(On A.C. models a similar horn specifically designed
for A.c. current is fitted.) The method of operation
is that of a magnetically operated armature. which
Impacts on the cone face, and causes the tone disc
of the horn to vibrate. The magnetic circuit is
made self interrupting by contacts which can be
adjusted externally.
If the horn fails to work. check the mounting bolts
etc .. and horn connection wiring. Check the battery
for state of charge. A low supply voltage at the
horn will adversely effect horn performance. If
the above checks are made and the fault is not
remedied, then adjust the horn as follows.
HORN ADJUSTMENT
When adjusting and testing the horn. do not depress
the horn push for more than a fraction of a second
or the circuit wiring may be overloaded.
A small serrated adjustment screw situated near the
terminals (see Fig. H24). is provided to take up
wear in the internal moving parts of the horn. To
adjust, turn this screw anticlockwise until the
horn just fails to sound. and then turn it back
(clockwise) about one quarter to half a turn.
ADJUSTMENT SCREW
00
147
FiB. H24. Horn adjustment screw
SECTION HII
HEADLAMP
DESCRIPTION
The headlamp is of the sealed beam unit type and
access is gained to the bulb and bulb holder by
withdrawing the rim and beam unit assembly. To
do so on the T120 or TR6. slacken the screw at the
top of the headlamp or on the earlier 6T. slacken
the screw at the top of the nacelle cover adjacent
to the and in each case prise off the
rim and beam unit assembly.
The bulb can be removed by first pressing the
cylindrical cap inwards and turning it anti clockwise.
The cap can then be withdrawn and the bulb is free
to be removed.
When fitting a new bulb. note that it locates by
means of a cutaway and projection arrangement.
also note that the cap can only be replaced one way.
the tabs being staggered to prevent incorrect
reassembly. Check the replacement bulb voltage
and wattage specification and type before fitting.
Focusing with this type of beam unit is unnecessary
and there is no provision for such.
BEAM ADJUSTMENTS
The beam must in all cases be adjusted as speCified
H24
by local lighting regulations. In the United Kingdom
the Transport Lighting Regulations reads as
follows:-
A lighting system must be arranged so that it can
give a light which is incapable of dazzling any person
standing on the same horizontal plane as the vehicle
at a greater distance than twenty five feet from the
lamp. whose eye level is not less than three feet-
six inches above that plane.
The head lamp must therefore be set so that the
main beam is directed straight ahead and parallel
with the road when the motorcycle is fully loaded.
To achieve this. place the machine on a level road
pointing towards a wall at a distance of 25 feet away.
with a rider and passenger, on the machine. slacken
the two pivot bolts at either side of the headlamp
and tilt the head lamp until the beam is focused at
approximately two feet six inches from the base
ofthe wall. Do not forget that the head lamp should
be on "full beam" lighting during this operation.
On machines with the nacelle slacken the two small
screws on the adaptor rim at either side to tilt the
beam unit.
ClassicBike.biz
ELECTRICAL SYSTEM
H
SECTION HI2
REMOVING AND REFITTING THE HEADLAMP
then slacken the light unit securing screw at the
top of the headlamp. Prise the top of the light
unit free.
Detach the pilot bulbholder from the light unit
and disconnect the main bulbholder leads at the
snap connector. Disconnect the -4 spade terminals
from the lighting switch and the terminals from the
ammeter. On earlier models merely disconnect
the snap connector terminals at the wiring
harness. The red leads for the warning lights
should be parted at the snap connectors and then
the harness complete with warning light bulb-
holders can be withdrawn with the grommet from
the back of the headlamp shell. Finally remove the
pivot bolts to release the shell and collect the
spacers.
Refitting is the reversal of the above instruction
but reference should ~ made to the wiring diagram
in Section H19. Finally. set the headlamp main beam
as shown in Section H11.
Do not tighten the headlamp pivot bolts over the
torque setting given in "General Data",
SECTION HI3
TAIL AND STOP LAMP UNIT
Access to the bulbs in the tail and stop lamp unit is
achieved by unscrewing the two slotted screws
which secure the lens. The bulb is of the double-
filament offset pin type and when a replacement is
carried out. ensure that the bulb is fitted correctly.
Check that the two supply leads are connected
correctly and check the earth (ground) lead to the
bulb holder is in satisfactory condiUon.
When refitting the lens. do not overtighten the
fixing screws or the lens may fracture as a result.
SECTION HI4
FUSES
FI,. H15. Exploded view of fuseholder assembly
The fuse is to be found on the brown(blue live lead
from the battery negative terminal after DU.66246
and on the red earth lead from battery positive
before this number. It is housed in a quickly
detachable shell and is of 35 amp fuse rating.
Before follOWing any fault location procedure always
check that the fuse is not the source of the fault.
A new fuse-cartridge should be fitted if there Is
any doubt about the old one.
A fuse can be fitted to any Triumph coil ignition
model and all that is reqUired is a small proprietary
fuse holder obtainable from most Triumph Dealers.
In all cases the fuse rating must not under any cir-
cumstances be below 35 amp. rating and must be
fitted on the earth lead between earth (ground) and
the battery positive terminal.
H25
ClassicBike.biz
H ELECTRICAL SYSTEM
SECTION HIS
IGNITION SWITCH
Coil ignition editions of the TR6 and T120 models
are fitted with an ignition switch incorporating a
"barrel" type lock. These locks use individual
"Yale" type keys and render the ignition circuit
inoperative when the switch is turned off and the
key removed. It is advisable for the owner to note
the number stamped on the key to ensure a correct
replacement in the event of the key being lost.
Three Lucar connectors are incorporated in the
switch and these should be checked from time to
time to ensure good electrical contact. The switch
body can be released from the headlamp bracket or
switch panel by removing the large nut retaining
the switch in the panel and the switch pushed out.
The battery leads should be removed before
attempting to remove the switch to avoid a short
circuit.
The lock is retained in the body of the switch by a
spring loaded plunger. This can be depressed with a
pointed instrument through a small hole in the side
of the switch body and the lock assembly with-
drawn after the lock and switch together have been
detached from the machine.
Fig. H26. Showing the ignition switch
(TR6 and T120 models)
SECTION HI6
IGNITION CUTOUT ("KILL") BUTTON
An emergency cut-out (kill) button is provided on
TR6 and T120 models. This is mounted on the
handlebar and can be used to stop or "kill" the
engine.
NOTE: Two types of cut-out buttons are in
current use, one for coil ignition machines and one
for A.C. magneto equipped machines. Although
both cut-out buttons appear identical externally,
the internal connections are arranged differently.
They must not be interchanged and if a replacement
is required, refer to the appropriate replacement
parts list.
H26
327
IGNITION
CUT-OUT
BUTTON
Fig. H27. Ignition cut-out button
(TR6 and T120 models)
ClassicBike.biz
ELECTRICAL SYSTEM H
SECTION HI7
WARNING LAMPS
Warning lamps have been incorporated in the TR6
T120 electrical systems in recent years, the lamps
being mounted in the headlamp shell. On earlier
machines having only a warning light for the ignition,
this is coloured red. On all machines with two
warning lights, red is used for the main beam and
green for the ignition warning.
A.c. Magneto models have a single red warning
light for main beam.
The ignition warning light is not intended to act as
a "no charge" lamp as in automobile practice. Its
function is to warn a rider that he has omitted to
switch off the ignition with the key provided.
LIGHTING
SWITCH
l
Fig. H28. Location of ignition and main beam warning
lamps (TR6 and T1l0 only)
Fig. H29. Location of main beam warning lamp
(A.C. magneto models only) (up to DU.66246)
H27
ClassicBike.biz
H ELECTRICAL SYSTEM
SECTION HI8
CAPACITOR IGNITION (MODEL 2MC)
The Lucas motor cycle capacitor system has been
developed to enable machines to be run with or
without a battery. The rider therefore has the
choice of running with normal battery operation or
running without battery if desired (e.g. competing
in trials or other competitive events) and for
emergency operation in case of battery failure.
Machines can readily be started without the battery
and run as normal with full use of standard lighting.
When stationary. however, parking lights will not
work unless the battery is connected. The capacitor
system also has the advantage of being much less
critical with regard to alternator timing.
Fig. H30. Capacitor and spring
The system utilises the standard 12-volt battery-coil
ignition equipment with the Zener diode charging
regulator mounted on an efficient heat sink. plus a
spring mounted high capacity electrolytic capacitor
(Model 2MC). of a special shock-resistant type.
The energy pulses from the alternator are stored
by the capacitor to ensure that sufficient current
H18
flows through the ignition coil at the moment of
cohtact opening, thus producing an adequate spark
for starting. When running. the capacitor also
helps to reduce the d.c. voltage ripple.
Also with this system alternator timing is much less
critical. Provided the centres of the rotor and
stator poles are roughly in line in the fully retarded
position (I.e. as normal battery) emergency start
condition which is 30 past magnetic neutral)
satisfactory starting will be obtained. Furthermore
any auto-advance angle and speed characteristics
may be used and perfect running ignition perfor-
mance achieved.
HEAT SINK REQUIREMENTS
With the diode centrally mounted flat on its base in
metal to metal contact with the plate. the assembly
should be mounted on the machine so that the
heat sink is in an unobstructed air stream. and in a
position to avoid as far as possible any dirt or water
th rown up by the wheels.
Earlier machines wired to give only part generator
output in the "off" and "pilot" positions will not
have heat sinks of suffiCient size. These must,
therefore. be replaced with one of the latest finned
type. It is essential that the heat sink is properly
earthed.
IDENTIFICATION OF CAPACITOR
TERMINALS
The 2MC capacitor is an electrodytic (polarised)
type and care must be taken to see that the correct
wiring connections are made when fitting. Spare
Lucar connectors are supplied to assist in connecting
up. Looking at the terminal end of the unit it will
be seen that there are two sizes of Lucar connector.
The small -ft in. Lucar is the positive (earth) terminal
the rivet of which is marked with a spot of red
paint. The double * in. Lucar forms the negative
terminal.
The illustration on the previous page shows the
spring and capacitor. The capacitor should be
positioned with its terminals pointing downwards.
When fitting the spring to the capacitor. insert the
capacitor at the widest end of the spring and push
it down until the small coil locates in the groove on
the capacitor body.
ClassicBike.biz
ELECTRICAL SYSTEM
H
STORAGE LIFE OF MODEL 2MC
CAPACITOR
The life of the 2MC is very much affected by storage
in high temperatures. The higher the temperature
the shorter its shelf life. At normal temperature
i.e. 20'C, (68'F.) it will have a shelf life of about 18
months. At 40'C, (86"F.) about 9 to 12 months.
Therefore, storing in a cool place will maintain
their efficiency.
TESTING
The efficiency of a stored capacitor can be deter-
mined fairly accurately with the air of a voltmeter
(scale 0-12 volts) connected to the terminals of a
charged capacitor and the instantaneous reading on
the meter noted. The procedure is as follows:-
(a) Connect the capacitor(s) to a 12-volt supply and
leave connected for 5 minutes. Observe care-
fully the polarity of connections, otherwise the
capacitor may be ruined.
(b) When charging time has been completed. dis-
connect the supply leads and allow the charged
capacitor(s) to stand for at least 5 minutes.
(c) Then connect the voltmeter leads to the
capacitor and note the instantaneous reading.
This should not be less than 80 volts for a
serviceable unit.
If a voltmeter is not available a rough check can be
made by following the procedures in (a) and (b)
and using a Single strand of copper wire instead of
the voltmeter to short-circuit the capacitor ter-
minals. A good spark will be obtained from a
serviceable capacitor at the instant the terminals
are shorted together.
WIRING AND INSTALLATION
The capacitor is fitted into the spring and should
be mounted with its terminals downwards. The
capacitor negative terminal and Zener diode must
be connected to the rectifier centre (d.c.) terminal
(brown/white). and the positive terminal must be
connected to the centre bolt earthing terminal (see
capacitor ignition terminal Fig. H30).
The mounting spring should be attached to any
convenient point under the twin seat.
Note.-Check to see if the Zener diode heat sink
is of the latest finned type. If not it must be replaced
with one that is (Service bulletin 288 describes
heat sink conversion, refer to Section H7).
The alternator should be reconnected to give full
output in all lighting switch positions. This can be
done by joining together the alternator external
green/black and green/yellow leads with the aid of
a double snap-connector. Machines after DU.66246
are th us arranged.
SERVICE NOTES
Before running a 2MC equipped machine with the
battery disconnected it is essential that the battery
negative lead be insulated to prevent it from re-
connecting and shorting to earth (frame of machine).
Otherwise, the capacitor will be reuined. This can
be done by removing the fuse from its holder and
replacing it with a length of * in. dia, dowel rod or
other insulating medium,
A faulty capacitor may not be apparent when used
with a battery system. To prevent any incon-
venience arising. periodically check that the
capacitor is serviceable by disconnecting the
battery to see if the machine will continue to run
in the normal manner, with full lighting also
available.
A capacitor kit is available under part number
C.P.210.
H29
ClassicBike.biz
E
III
Iii
>-
III
..J
00(
u
iii:
ti
III
..J
III
LIGHTING
POSITIONS
r ,- "ll
OFF
,
o
6
<5
3 ,
5 6
- 8
, 0
TAIL/PILOT
INSTRUMENTS
2
o
ALTERNATOR
- _-D

::'l green

c-

f I yellow
'II red
CAPACITOR
(ALTERNATIVE)
TAIL
INSTRUMENTS
HEADLIGHT
RECTIFIER
-----<=J--- SNAP CONNECTORS
__ -,r",e",d--{!I' EARTH CONNECTIONS
MADE VIA CABLE HORN HORN PUSH
OR
------;!'. VIA FIXING BOLT
,-, brown: black ___
0
brown / white
brown/white
::c brown/blue - + 1 red
c : O--+---='-i!I'
AMMETER 1 ___ _
e HEADLAMP MAIN BEAM
red brown T.c WARNING LIGHT (RED)
,-----------<c- white
HEADLAMP MAIN BEAM

DIPPER ,--__
SWITCH blue white
HEADLAMP DIP BEAM
I blue' red () red .
L ____
PILOT LIGHT
E
o

red I black 1/1

o
SPEEDOMETER ILLUMINATION
;;
___ ___ --{I' E
f
brown white
DO
TACHOMETER
...
brown / reen
.;:

TAIL LAMP
brown ,i reen brown I' green () I ;:;
L-f-----=-=-L::''>-'-'-'------c J:
IGNITION
WARNING LlGHT(GREEN) STOP LAMP
SWITCH
STOP LAMP
IGNITION
SWITCH
ZENER DIODE
white
white
brown brown
'
black/white
black/yellow
black/white
.------c'::::J------{] I'
CONTACT
BREAKERS
\-+--------11'
L---c::J---{] 1r----11'
black,'yellow
..
ii:
ClassicBike.biz
1:
w
Iii
)0-
1/1
oJ
<1:
u
iii:
t
w
oJ.
w
LIGHTING
POSITIONS
7
OFF
8
o
2
o
ALTERNATOR
green/
yellow ___
7
8
o
TAIL/PILOT
INSTRUMENTS

1'1' OJ
'2&

'"
Cl
'II __ -K
4 ,
o
56,
CAPACITOR
(ALTERNATIVE)
TAIL
INSTRUMENTS
HEADLIGHT
RECTIFIER

:c

--<=J-- SNAP CONNECTORS
__ EARTH CONNECTIONS
MADE VIA CABLE HORN HORN PUSH
OR
___ ---'po VIA FIXING BOLT
brown, black --)-___ ..jll.
r' 0
brown/white
brown / white
""2;1 brown/blue - + J red
o ,
HEADLAMP"MAIN BEAM
_____ .::bc.r0c.w'-'<:n='w""'hc.i tc.:e--<: t .0 WARN I NG LIGHT (RED)
blue white
red
LIGHTING
HEADLAMP MAIN BEAM
DIPPER
SWITCH SWITCH blue. white
blue blue
HEADLAMP DIP BEAM
Itf
3 4
5 6 red/
I
black
7
8
,
9 blue. r rpedd () .. r"'erld '
IL ____
PILOT LIGHT
_____ ____ __
__ ___ -c,xo-__ --II'
TACHOMETER ILLUMINATION
brown green
I'
brown, white
TAIL LAMP
brown ,'green
l--.J
L-+-______
brown ,.
,
green
II'
IGNITION
WARNING LlGHT(GREENl STOP LAMP STOP LAMP
SWITCH
_ brown brown I
r-LJ-U O-------C::::.J----l _
white
black 'white ,------.J
-, L}-------{] ir---jl'
, I - - --, CONTACT
L,-==-:-c-;:-:c-+---'j: BR EA K E R S
black white

:c 2CP CONDENSOR PACK I' ZENER DIODE
11-- , r-----iJ ir----jl'
black 'yellow black vellow
.-
E
o
J:

::J
Q
E
o
.::

..
."
o
E
...
M
J:
..
u:
ClassicBike.biz
:E
w
Iii
>-
(II
oJ
"
v
iii:
l-
V
w
oJ
w
SWITCH ROTOR
POSITIONS VIEWW FROM
REAR OF SWITCH

(3) Cij
'OFF
A;) 0 (3)

CD 1
8 10 11
l POSITION
H POSITION
359
ALTERNATOR
'"
o.
1::0
green/
yellow __
RECTIFIER
!
:;;

---c:l-- SNAP CONNECTORS
_
__ !l,e",d'-"I
I'
EARTH CONNECTIONS
MADE VIA CABLE HORN
OR
VIA FIXING BOLT
c
:o
brown/white
brown I white
o

o
.c
brown blue
o.
AMMETER
. .-.-... e
brown "white toO
HEADLAMP MAIN BEAM
WARNING LlGHT(RED)
white
[.
LIGHTING
SWITCH
DI PPER r-_____ I'
SWITCH
_(5)00 blue
C!).? 2
blue
"""" HEAD LAMP DIP BEAM
T blue._' red () red .
(])
L-__
PILOT LIGHT
>--__ ---'-"e"'d'--"'bl"'a"'ck'----___ ---<J20 __ -lII.
brown green
,--_...:::.::::::.:c..l!:..::.::::.... __ -o><O-_--II
brown.' reen brown reen
===c;--,"----"""'"---"'-"'"'------oX<e>------1I
o
TAIL LAMP

.c
L+ ____ b_w_w-;n _'
brown green () .

IGNITION
WARNING LlGHT<GREEN) STOP LAMP SWITCH & LAMP

white
white
ENGINE CONTACT
CUT - OUT BREAKERS
IGNITION
SWITCH
.!: SWITCH
L
____ --'b"',,ac'""k, "'white 1 h" __ -lil'
1: '- black' [JL
_IL __ J white
'----'0
"c"----7C-c-----' ... ;;-:-_[ . /black IIU' j!jl._--III'
black yellow yellow
ZENER DIODE
COILS
ClassicBike.biz
1:
w
l-
II)
)0-
Il)
..J

u
II:
IJ
w
..J
W
SWITCH ROTOR
PO::;lTIONS VIEWED fROM
REAR OF SWITCH
'OFf
/ts)0G)

(2) 1
10 11
'l POSITION
H POSITION
360
ALTERNATOR
RECTIFIER
----.- SNAP CONNECTORS
__ -,-"e",d'-1II' EARTH CONNECTIONS
MADE VIA CABLE
OR
------ill' VIA FIXING BOLT
LIGHTING
SWITCH
AMMETER
blue blue
HORN HORN PUSH
brown black
o-----jll,

HEADLAMP MAIN BEAM
DIPPER
SWITCH blue/white
HEAD LAMP DIP BEAM
blue' red
PILOT LIGHT
red,/
- L{=>------'-'=.c="-----<>"'-O-------i I'
IGNITION
SWITCH
brown I
TAIL LAMP
IGNITION
WARNING LIGHT (GREEN) STOP LAMP SWITCH & LAMP
brown brown
r-cJ-O
ENGINE CONTACT
CUT - OUT BREAKERS
CONDENSERS
COILS
ClassicBike.biz
E
IU
I;;
>-
III
oJ
c(
u
ii2
tJ
IU
oJ
IU
RED
STOP-TAIL
LAMP
STOP LAMP
SWITCH
r-__________
BROWN
BLACK/YELLOW
BLUE
IDENT
BROWN BLUE
COIL
COIL
RED
152
LIGHTING
SWITCH
r-C::J------l.o:,.oJ>---lI'
BROWN/
GREEN
DIP
SWITCH
HEADLAMP
BLACK/YELLOW
CONTACT
BREAKER
CUT-OUT)
BUTTON
Fig. H35. Wiring diagram-A.C.Magneto (E.T. Ignition) models
Note. The main beam warning lamp (where fitted) is connected to the headlamp main beam wire by a double
snap connector. No ignition warning lamp is fitted.
ClassicBike.biz
1:
W
I-
III
)0-
III
..J
<!
U
ii:
I-
U
w
..J
W
ROTOR POSITIONS VIEWED
FROM REAR OF SWITCH
'OFF' POSITION

':/
(J) 1
8 10 11
l POSITION
flO
3
2
7 CD
H POSITION
IGNITION SWITCH

3 @)

15 16
'OFF' pOSITION

13

14 17
15 16
IGN ' POSITION
ALTERNATOR

.!1
-.;
,.,
c

'"
red 1,
RECTIFIER

red II'

brown I white
LIGHTING
SWITCH
3 blue
(J)
STOP LAMP STOP LAMP SWITCH
brown brown brown --white _
,1!----<0O:-:-:=---c=="'----c-=----o
HORN PUSH HORN
I
brown /black
, I 1-----<0
brown/blue
AMMETER 12-VOLT BATTERY
L-____
brown/white
O>1-'_____ -.C
r
-"e"'d--l1
1
'
+J
PILOT LAMP
red' black

E
s: brown! reen
I:: brown reen

o
.c
blue
DIPPER
SWITCH
HEADLAMP MAl'" BEAM
blue 'white ()
"];::':::---<c;Xo red [I'
HEADLAMP DIP BEAM
red II'
TAIL LAMP
L-__ -,>-_____ I '
r:12@
I browll r.een
it. IGNITION I'
@ SWITCH white
white
white
- I, COIL
.cb +
SNAP CONNECTORS
EARTH CONNECTIONS
MADE VIA CABLE
OR
VIA FIXING BOLTS
ZENER
DIODE
L--tw=h"i _ sw _
COIL , -",cll t-

- eJp ____ -j!I' CONTACT
I,. BREAKERS
Fig. H36. Wiring diagram-Coil ignition 12 volt models with nacelle from engine number DU.2487S
Note. The main beam warning lamp (where fitted) is connected to the headlamp main beam wire (blue/white) by a double
snap connector. The ignition warning lamp is connected to an ignition coil by a white wire incorporated in the wiring harness.
ClassicBike.biz
I:
III
l-
II)
)0-
Il)
...I
c(
V
a:
l-
V
III
...I
III
GREEN/YELLOW
CK
UJ
3
'"
GRE
BLUE
BR<JWI'.VWHITE
STOP
STOP
LIGHT
'11__ BROWN S IT H
0---,
HORN

BROWN B E
6. VOLT.-
BATTERY
+

p () FILAMENT
BLUE/RED oXo RED III
L
__ II
L
______ __
II
L
__________ ____ __
II
2
3
.c:;,. IQNITION
II::i' SWITCH 8
@--, 7

II
ElL WHITE
WHITE ,'Ii. IGNITION
COIL- LEFT
UJ ,w- IGNITION

15
YELLOW
lj
--....IO}---- :::l SNAP CONNECTORS'"
_______ --lIIIEARTH
__ -SWITCH CONNECTIONS
BLAO(
CONTACT
REAKER
IS,

c '"
...

.c"!

'i
C

.!!
... ." E
o
E c
>
.... -
- ..
c c
.2 :
.t: ""
c .l!
.. .
:'"
8

f
='
:;;
..
c
.;:

..
i!
ClassicBike.biz
4
BLUE
5
STOP
LAMP
STOP
LAMP
SWITCH
BROWN
:.. -Jo' 2
GREEN/BLACK lL ______ --d A p. ___ ____ -I-_-O-1.J
SWITCH 1)-1-,--' b VOLT
.--, , AMMETER BATTERY
(
I A ),) MAIN
V ' I ' FI JiMENT FUSE
BLACK II_
I BLUE H'ADLAMP DIP FILAMENT I
DIP SWITCH () w
!::
%

Z
w
w
'"
'"
ALTERNATOR
w
W
!::
YO
I-
%
%
-'
51
"-
"-
Z

Z

'"
51
a:
51
,@

---: 17 1
91:.---10 BLACK
BROWN/GREEN
SPEE01, LIGHT
I
I-
l
BROWN/ GREEN

I
I'
l
REO/BLACK

I
I-
I
WHITE
18
5
16 --,
WHITE r a'W- llGNITION
L
___ COIL- LEFT
C5sw- jlGNITION
YO COIL - RIGHT GREEN/YELLOW
SNAP CONNECTORS
-----jll- EARTH CONNECTIONS
--------- SWITCH CONNECTIONS
!:: IISLACK/
YEllOW
"-
L-__ 1--<>-__/
CONTACT
BREAKER
149
ClassicBike.biz
:t
w
I-
en
>-
en
....I

=
ti
w
....I
W
BOOST
SWITCH
:c(5 J@3_)-_-"B",LU,-,, __
:5 c. -'V 2 1'----r:======3:j
al GREEN/Bl.ACK LIGHTING ......
STOP STOP
LAMP
SWITCH
'If- __ -CJ--__ --{=>,8:c':::O:::W:::N,---<:-- (
HORN z
PUSH
I _
11r-'" aJ
/BLUE.
A(r ___ _____
b 1I0Ll ? ,-=""'CL!!""""----+---<7 SWITCH I

\
BATTERY I ( +
AMMETER
"
m
0 I
" U V I
f{
I' MAIN
FUSE
I

BLACI< I
BROWN/WHITE
w
!::
"

z
:::
'"
"
ALTERNATOR
w
"

..
w
':
"

z

'"
..
2
A
@
13
BLUE
BROWN / GREEN
BROWN/ GREEN
RED/BLACK
@----: 17; WHITE
HEADLAMI?
DIP SWITCH
9
0
l
I'
DIP FilAMENT
BLACt<.
Jb
I
I'
SPHD_O. LIGHT
I,

I'
PILOTJ>'IGHT
I,
18
5 16 --, I WHITE r a'W- j'GNITION
L. __ _____ COIL- LEFT

..
."
o
E
ClassicBike.biz
SECTION J
WORKSHOP SERVICE TOOLS
INTRODUCTION
This section of the Workshop Manual illustrates pictorially the workshop service tools that are available
for carrying out the major dismantling and re-assembly operations on the UNIT CONSTRUCTION 650 c.c.
Triumph Motorcycle.
The section is divided into sub-sections relating to the main section headings in this manual, illustrating
those tools mentioned and used in the appropriate section text.
Section
ENGINE ... J1
TRANSMISSION J2
GEARBOX J3
WHEELS H
FRONT FORKS J5
MOTORCYCLE TOOLKIT J6
J1
ClassicBike.biz
J
12
61-6063. Valve guide removal
and replacement tool
SERVICE TOOLS
SECTION J I
(
ENGINE
61-6008. Tappet guide block punch
D18ll. Valve seat cutter (inlet)
DtBn. Valve seat cutter (exhaust)
01836. Blending cutter (inlet)
D18lS. Blending cutter (exhaust)
01863. Arbor, pilot and tommy bars
2618
ClassicBike.biz
SERVICE TOOLS
ENGINE (CONTINUED) Jl
Z22. Piston ring collar 103/3/4
02213. Camshaft pinion extractor
and replacer with adaptors
Z138. Crankshaft balance weight {689 gms.}
with Z107 spring
Z5S. Left side reamer, camshaft bushes
Z56. Arbor for left side reamer, camshaft bushes
26/3
0782. Contact breaker cam extractor
26/4
0486. Pilot for contact breaker oil seal when
replacing timing cover
T250
61-6019. Crankshaft pinion extractor
J
J3
ClassicBike.biz
J
SERVICE TOOLS
ENGINE (CONTINUED) Jt
CPl07. Stroboscope timing kit
D2014. Stroboscope timing plate
0571&
0572
333
e@0607
0606
0605
01859. Flywheel locating body and plunger
Z161. Roller bearing outer race removal tool
ClassicBike.biz
SERVICE TOOLS
J
ENGINE (CONTINUED) Jl
Z73. 14 mm. tap
Dm1. Oil seal compressor
for replacing the rocker spindle
103/7
Z79. Crankshaft pinion punch and guide
o
O@O
o
o
614014. Crankcase parting tool and sprocket extractor
. "
\'
\\
0605/8. Timing disc and adaptor with washers
51-51 Nut (see page J4 for separate Part Nos.)
JS
ClassicBike.biz
J
(
<
J6
SERVICE TOOLS
SECTION J2
TRANSMISSION
154 146
01861. Clutch hub extractor 0496. Chain tens loner adjuster plug DA70. Clutch nut screwdriver
klVET EXTRACTOR
IN POSITION
RIVET EXTRACTOR
WITH JAWS OPEN
91
167. Rear chain rivet extractor
SECTION J3
GEARBOX
[)
61-6026. _ Gearbox -:Shouldered punch 156
61-6010. Reamer (or gearbox high gear bush 157
Z13. Clutch locking plate
Z63. Gearbox nut box spanner
ClassicBike.biz
SERVICE TOOLS
SECTION J4
WHEELS
, . spanner
61-3694.tWheel bearing locking ring
t box spanner 61
6062. Anchor :huoe brake
for twin lea In
SECTION J5
FRONT FORKS
. tool
I nd'l!refittlng . -.. emova a .. Fork stanchion. 61.3824.

Front-fork
616025. ge
alignment gau
J
J7
ClassicBike.biz
J
SERVICE TOOLS
FRONT FORK (CONTINUED) JS
61.6017. Fork sleeve nut spanner
0779. Fork cap spanner
J8
ClassicBike.biz
CONVERSION
TABLES
CT1
ClassicBike.biz
CT
en
CONVERSION TABLES
INCHES TO MILLIMETRES-UNITS
Inches 0 10
0 2540
1 25-4 279-4
2 508 3048
3 762 3302
4 10106 3556
5 1270 3810
6 152-4 4064
7 17].8
4318
8
20].2 4572
9 2286 48206
One Inch-25 399978 millimetres
One Metre-39370113 inches
One Mile-1 6093 kilos
One Kilo-62138 miles
20 30 40
5080 7620 10160
53H 787-4 1041-4
5588 812-8 10668
5842 8382 1092-2
60% 863-6 111].6
6350 8890 11430
6604 91404 1168-4
6858 9398 1193a
7112 9652 12192
7366 9906 124406
DECIMALS TO MILLIMETRES-FRACTIONS
1/1000 1/100 1/10
inches mm. inches mm. inches mm.
001 0254 01 254 1 254
002 0508 02 508 2 508
003 0762 03 -726 3 ].62
004 1016 04 1-016 4
-;0::;6
005 1270 05 1270 5 12-70
006 1524 06 1524 6 1524
--
007 1778 07 1778 7 17-79
008 2032 08 2032 8 2032
009 22a6 09 2-286 9 22-86
ClassicBike.biz
CONVERSION TABLES CT
FRACTIONS TO DECIMALS AND MILLIMETRES
Fractions Decimals mm. Fractions Decimals mm.
1/64 015625 3969 33/64 515625 13-0969
1/32 -03125 7937 17/32 53125 13-4937
3/64 046875 11906 35/64 546675 138906
1/16 0625 15875 9/16 5625 14-2875
5/64 078125 1-9844 37/64 578125 14-6844
3/32 09375 23812 19/32 59375 150812
7/64 109375 2-7781 39/64 609375 15-4781
1/8 125 31750 5/8 625 158750
9/64 140625 35719 41/64 640625 162719
5/32 15625 39687 21/32 65685 166687
11/64 171875 43656 43/64 671875 170656
3/16 1875 4-7625 11/16 6875 174625
13/64 203125 51594 45/64 703125 178594
7/32 21875 55562 23/32 -71875 182562
15/64 234375 59531 47/64 -734375 186531
1/4 25 63500 3/4 75 190500
17/64 265625 67469 49/64 765625 194469
9/32 28125 71437 25/32 78125 19-8437
19/64 296875 75406 51/64 796875 202406
5/16 3125 79375 13/16 8125 206375
21/64 328125 83344 53/64 828125 21-0344
11/32 34375 87312 27/32 84375 21-4312
23/64 359375 91281 55/64 859375 218281
3/8 375 95250 7,18 875 22-2250
25/64 390625 i ~ 57/64 890625 22-6219
13/32 40625 103187 29/32 -90625 23-0187
27/64 421875 10-7156 59/64 921875 23-4156
7/16 4375 111125 15/16 9375 238125
29/64 453125 115094 61/64 953125 242094
15/32 46875 119062 31/32 96875 24-6062
31/64 484375 123031 63/64 984375 25-0031
1/2 5 12-7000 1 25-4000
I
cn
ClassicBike.biz
CT CONVERSION TABLES
MILLIMETRES TO INCHES-UNITS
mm_ 0 10 20 30 40
0 -39370 -78740 1-18110 1-57480
1 -03937 -43307 -d2677 1-22047 1-61417
2 -07874 -47244 -86614 1-25984 1-65354
3 -11811 -51181 -90551 1-29921 1-69291
4 -15748 -55118 -94488 1-33d58 1-73228
5 -19685 -59055 -98425 1-37795 1-77165
6 -23622 -62992 1-02362 1-41732 1-81103
7 -27559 -66929 1-06299 1-45669 1-85040
8 -31496 -70866 H0236 1-49606 1-88977
9 -35433 -74803 H4173 1-53543 1-92914
mm_ 50 60 70 80 90
0 1-96851 2-36221 2-75591 3-14961 3-54331
1 2-00788 2-40158 2-79528 3-18891 3-58268
2 2-04725 2-44095 2-83465 3-22835 3-62205
3 2-08662 2-48032 2-87402 3-26772 3-66142
4 2-12599 2-51969 2-91339 3-30709 3-70079
5 2-16536 2-55906 2-95276 3-34646 3-74016
6 2-20473 2-59843 2-99213 3-38583 3-77953
7 2-24410 2-63780 3-03150 H2520 3-81890
8 2-28347 2-67717 3.Q7087 H6457 3-85827
9 2-32284 2-71654 3-11024 3-50394 3-89764
MILLIMETRES TO INCHES-FRACTIONS
1/1000 1/100 1/10
mm_ inches mm_ inches mm_ inches
0-001 -000039 0-01 -00039 0-1 -00394
0-002 -000079 0-02 -00079 0-2 -00787
0-003 -000118 0-03 -00118 0-3 -01181
0-004 -000157 0-04 -00157 0-4 -01575
0-005 -000197 0-05 -00197 0-5 -01969
0-006 -000236 0-06 -00236 0-6 -02362
0-007 -000276 0-07 -00276 0-7 -02756
0008 -000315 0-08 -00315 0-8 -03150
-
0-009 -000354 0-09 -00354 0-9 -03543
I
CT4
ClassicBike.biz
DRILL SIZES
Letter Size Letter Size Number Size Number Size Number Size Number Size
A 234 N 302 1 2280 14 1820 27 1440 40 0980
B 238 0 316 2 2210 15 1800 28 1405 41 0960
C 242 P 323 3 2130 16 1770 29 1360 42 0935
D 246 Q 332 4 2090 17 1730 30 1285 43 0890
E 250 R 339 5 2055 18 1695 31 1200 44 0860
F 257 5 348 6 2040 19 1660 32 1160 45 0820
G 261 T 358 7 2010 20 1610 33 1130 46 0810
H 266 U 368 8 1990 21 1590 34 1110 47 0785
I 272 V 377 9 1960 22 1570 35 1100 48 0760
J 277 W 386 10 1935 23 1540 36 1065 49 0730
K 281 X 397 11 1910 24 1520 37 1040 50 -0700
L 290 Y 404 12 1890 25 1495 38 1015 51 0670
M 295 Z 413 13 1850 26 1470 39 0995 52 0635
WIRE GAUGES
No. of Imperial Standard Brown and Sharpe's
Gauge Wire Gauge American Wire Gauge
Inches Millimetres Inches Millimetres
0000 400 10160 460 11684
000 372 9448 410 10404
00 348 8839 365 9.265
0 324 8299 325 8251
1 300 7-620 289 7348
2 276 7010 258 6543
3 252 6400 229 5827
4 232 5892 204 5189
5 212 5384 182 4-621
6 192 4676 162 4115
7 176 4-470 144 H64
8 160 4064 128 3263
9 144 3-657 114 2906
10 128 3251 102 2588
11 116 2946 091 2304
12 104 2641 081 2052
13 092 2336 072 1827
14 080 2032 064 1-627
15 072 1828 057 1449
16 064 1-625 051 1290
17 056 1-422 045 1149
18 048 1219 040 1-009
19 040 1-016 035 911
20 036 914 032 811
21 032 812 028 722
22 028 711 025 643
23 024 609 023 573
24 022 558 020 511
25 020 508 018 454
26 018 457 016 404
27 0164 416 014 360
28 0148 375 012 321
29 0136 345 011 285
30 0124 314 010 254
CTS
ClassicBike.biz
FOOT POUNDS TO KILOGRAMETRES
0 1 2 3 4 5 6 7 8 9
-
0-138 0-227 0-415 0-553 0-691 0-830 0-968 1-106 1-244 -
10 1-383 1-521 1-659 1-797 1-936 2-074 2-212 2-350 H89 2-627 10
20 2-765 2-903 3-042 3-180 3-318 3-456 3-595 3733 3-871 4-009 20
30 4-148 4-286 4-424 4-562 40701 4-839 4-977 5-116 5-254 5-392 30
40 5-530 5-668 5-807 5-945 6-083 6-221 6-360 6-498 6-636 6-774 40
50 6-913 7-051 7-189 7-328 7-466 7-604 7-742 7-881 8019 8-157 50
60 8-295 8-434 3-572 8-710 8-848 8-987 9-125 9-263 90401 9-540 60
70 9-678 9-816 9-954 10-093 10-231 10-369 10-507 10-646 10-784 10-922 70
80 11-060 11-199 11-337 11-475 11-613 11-752 11-890 12028 12166 12305 80
90 12-443 12-581 12-719 12-858 12-996 13-134 13-272 13-411 13-549 13-687 90
MILES TO KILOMETRES
0 1 2 3 4 5 6 7 8 9
-
1-609 3-219 4-828 6-437 8-047 9-656 11-265 12-875 14-484
-
10 16-093 17-703 19-312 20-922 22-531 24-140 25-750 27-359 28-968 30-578 10
20 32-187 33-796 35-406 37-015 38-624 40-234 41-843 43-452 45-062 46-671 20
30 48-280 49-890 51-499 53-108 54-718 56-327 57-936 59-546 61-155 62-765 30
40 64-374 65-983 67-593 69-202 70-811 7H21 74-030 75-639 77-249 78-858 40
50 80-467 82-077 83-686 85-295 86-905 88-514 90-123 91-733 93-342 94-951 50
60 96-561 98-170 99-780 101-389 102-998 104-608 106-217 107-826 1090436 111-045 60
70 112654 114-264 115-873 117-482 119-092 120701 122-310 12).920 125529 127138 70
80 128748 130-357 131-967 133-576 135185 136795 138404 140013 141-623 143-232 80
90 144-841 146451 148060 149-669 151279 152888 154-497 156107 157716 159325 90
POUNDS TO KILOGRAMS
0 1 2 3 4 5 6 7 8 9
-
0454 0907 1-361 1814 2268 2-722 3175 3-629 4-082
-
10 4536 4990 5443 5987 6350 6804 7257 7-711 8-165 8-618 10
20 9072 9525 9-079 10433 10886 11340 11-793 12247 12-701 13-154 20
30 13-608 H061 H515 14968 15-422 15-876 16329 16783 17237 17-690 30
40 18-144 18597 19-051 19504 19-958 20412 20865 21-319 21772 22226 40
50 22-680 23133 23587 24040 24494 24-948 25401 25855 26308 26-762 50
60 27216 27-669 28123 28576 29030 290484 29-937 30-391 30844 31298 60
70 31-751 32205 32-659 33112 33566 34019 340473 34-927 35-380 35834 70
80 36287 36741 37195 37-648 38102 38855 39-009 390463 39916 40370 80
90 40823 41277 41731 42-184 42-638 43-091 43-545 43-998 440452 44-906 90
MILES PER GALLON (IMPERIAL) TO LlTRES PER 100 KILOMETRES
10 2825 15 1883 20 1412 25 1130 30 9042 35 807 40 706 50 565 60 4-71 70 4-04
10t 2690 1St 1822 20t 13-78 25! 1108 30t 926 35t 7-96 41 6-89 51 5-54 61 4-63 71 3-98
11 2568 16 1766 21 13-45 26 1087 31 911 36 785 42 673 52 543 62 455 72 3-92
11t 24-56 1st 1712 21t 13-14 2st 1066 31t 897 36t 7-74 43 6-57 53 533 63 4048 73 3-87
12 23-54 17 1661 22 1284 27 1046 32 883 37 7-63 44 6-42 54 523 64 4041 74 3-82
12t
22-60
17i
1614 22t 12-55 27t 10-27 32t 8-69 37t 7-53 45 628 55 513 65 435 75 3-77
13 21-73 18 15-69 23 1228 28 1009 33 856 38 7-43 46 614 56 5-04 56 4-28 76 3-72
13t 2092 18t 1527 23t 12-02 2St 991 33t 8-43
3et 734 47 601 57 4-96 67 422 77 3-67
14 20-18 19 1487 24 1177 29 974 34 831 39 724 48 589 58 487 68 416 78 3-62
Hi
19-48 19t 1449 24t
1153 29t 958 34t 819 39t 715 49 5-77 59 4-79 69 4-10 79 357
CT6
ClassicBike.biz
0
-
-
t
142
t
284
t
426
0 1
- 4546
10 45-460 50005
20 90919 95-465
30 136379 140924
40 181838 186384
50 227298 231-843
60 272-757 277303
70 318217 322-762
80 36H76 368222
90 409136 41 H81
0 1
-
0070
10 0703 0773
20 1406 10476
30 2109 2179
40 2-812 H83
50 3-515 3-586
60 4218 4289
70 4-921 4992
80 5-624 5-695
90 6328 6398
CONVERSION TABLES
PINTS TO L1TRES
1 2 3 4 5 6
568 1-136 H05 2273 2841 3841
710 1279 1846 2415 2-983 3-552
852 H2O 1-989 2-557 3125 3125
994 1563 2131 20699 3-267 J.836
GALLONS (IMPERIAL) TO L1TRES
2
I
3 4 5 6 7
9092 13-638 18184 22-730 27276 31-822
54551 59097 63643 63189 72-735 77281
100011 104557 109103 113-649 118195 122-741
145-470 150016 154562 159108 163-645 168200
190930 195-476 200022 204568 209114 213-660
236389 240935 245-481 250027 2540473 259119
281849 286395 290941 295-487 300'Oll 304-579
327308 ll1-854 336400 340946 245-492 350038
372-768 377314 3d1860 386406 390952 3950498
418227 422-773 427319 431865 436411 440957
POUNDS PER SQUARE INCH TO
KILOGRAMS PER SQUARE CENTIMETRE
2 3 4 5 6 7
0141 0211 0281 0352 0422 0.492
0844 0914 0984 1055 1-125 1-195
1547 1-617 10687 1-758 1828 1898
2250 2-320 2-390 2-461 2531 20601
H53 3023 3-093 3164 3-234 3304
H56 3-726 J.797 3867 B37 4007
4359 40429 4500 4570 4640 40711
5062 5132 5203 5273 5)43 5-414
5-765 5835 5906 5976 6046 6117
6-468 6538 6609 6-679 6749 6820
CT
7 8
B78 4546
4120 4688
4262 4830
4404 4972
8 9
36368 40914
-
81827 86373 10
127287 131-833 20
172-746 177292 30
218206 222-752 40
26].605 268211 50
309125 313-671 60
354584 359130 70
400044 404590 80
445503 450049 90
8 9
0562 0633 -
1266 1-336 10
1969 2039 20
20672 2-742 30
3-375 3445 40
4078 41413 50
40781 4851 60
50484 5-554 70
6187 6257 80
6890 6960 90
CT7
ClassicBike.biz
U.N.E.F. SCREW THREADS
Dia. No. of thds. Core dia. Tap drill Dia. No. of thds. Core dia. Tap drill
-
1,/4 in. n 2162 in. 560 mrn. 1 in. 20 9459 in. 61/64 in.
5/16 in. n 2787 in. 720 mm. 1-1/16 in. 18 10024 in. 1010 in.
3/8 in.
I
32 3412 in. 11/32 ins 1.1/8 in. 18 10649 in. 1072 ins.
7/16 in. 28 3988 in. 1020 mm. 1-3/16 in. 18 11274 in. 1135 in.
1/2 in. 28 4613 in. 1180mm, 1-1/4 in. 18 11899 in. 1-196 in.
9/16 in. 24 5174 in. 1330 mm. 1-5/16 in. 18 1 2524 in. 3200 mm.
5:'8 in. 24 5799 in. 1475 mm. 1-3/8 in. 18 13149 in. 3350 mm.
11(16 in. 24 6424 in. 6480 in. 1-7/16 in. 18 13774 in. 1385 ins.
3/4 in. 20 6959 in. 45/64 in. 1-1/2 in. 18 14399 in. 14-17 in.
13/16 in. 20 7584 in. 49/64 in. 1-9/16 in. 18 14948 in. 1-1/2 in.
7/8 in. 20 8209 in. 53/64 in_ 1-5/8 in. 18 15649 in. 1572 in.
15/16 in. 20 8834 in. 57/64 in. 1-11/16 in. 18 16274 in. 4150 mm.
B.A. SCREW THREADS
Dia. of Thds. Dia. tap Core
No_ bolt per inch drill dia.
0 -2362 254 -1960 -1890
1 -2087 282 -1770 -1661
2 -1850 31-4 -1520 -1468
3 -1614 H-8 -1360 -1269
4 -1417 38-5 -1160 -1106
-
5 -1260 43-0 -1040 -0981
6 -1102 479 -0935 -0852
7 -0984 52-9 -0810 -0738
8 -0866 591 -0730 -0663
9 0748 651 -0635 -0564
10 -0669 72-6 -0550 -0504
11 -0591 81-9 -0465 -0445
12 -0511 90-9 -0400 -0378
13 -0472 102-0 -0360 -0352
14 -0394 1099 -0292 -0280
15 0354 120-5 -0260 -0250
16 -0311 1333 -0225 -0220
eTa
ClassicBike.biz
B.S.W. SCREW THREADS B.S.F. SCREW THREADS
Dia. of Threads Dia. tap Core
bolt per drill dia.
Dia. of Threads Dia. tap Core
bolt per drill dia.
(inch) inch (;nch) (;nch) inch (inch)
1/4 20 1968 1860 7/32 28 1770 1731
5/16 18 1/4 2412 1/4 26 2055 2007
3/3 16 5/16 2950 9/32 26 238 2320
7/16 14 23/64 3460 5/16 22 261 2543
1/2 12 13/32 3933 3/8 20 316 3110
--
9/16 12 15/32 4558 7116 1. 3/8 3664
5/8 11 17/32 5086 1/2 16 27/64 4200
11/16 11 37/64 5711 9/16 16 492 4825
3/4 10 41/64 6219 5/8 14 35/64 5ll5
13/16 10 45/64 6844 11/16 14 39/64 5960
7/8 9 3/4 7327
15/16 9 13/16 7952
3/4 12 21/32
I
6433
13/16 12 23/32 7058
1 8 55/64 8399 7/8 11 25/32 7586
1 10 57/64 8719
1-1/8 9 1 9827
1-1/4 9 1-1/8 11077
1-3/8 8 1-15(64 12149
1-1/2 8 1358 1ll99
,
1-5/8 8 1-31/64 1 -4649
I
U.N.C. SCREW THREADS U.N.F. SCREW THREADS
Dia.
I
No. of thds. Core dia. Tap drill
1/,4 in. 20 1959 in. 520 mm.
5.116 in. 18 2524 in. 660 mm.
3/8 in. 16 )073 in. 800 mm.
Dia. No. of thds. Core dia.
I
Tap drill
1/4 in. 28 2113 in. I 550 mm.
5/16 in. 24 2674 in.
I
690 mm.
I
3/8 in. 24 3299 in. 850 mm.
7/16 in. 14 3602 in. 940 rnm. 7/16 in. 20 3834 in. 990 mm.
--
1/2 in. 13 4167 in. 1080 mm. 1/2 in. 20 4459 in. 1150 mm.
9/16 in. 12 4723 in. 1220 mm. 9/16 in. 18 5024 in. 1290 mm.
s/a in. 11 5266 in. 1350 mm. 5/8 in. 18 5649 in. 1450 mm.
3/4 in. 10 6417 in. 1650 mm, 3/4 in. 16 6823 in. 11/16 in.
7/8 in. 9 -7547 in. 49/64 ;n. 7/8 in. 14 7977 in. 0804 in.
1 in. 8 8647 in. 2225 rnm. 1 in. 12 9098 in. 2325 mm.
1-1/3 ;n. 7 9704 in. 63/64 in. 1-1j8in. 12 10)48 in.
I
2650 mm.
1-1/4 in. 7 10954 in. 1-7/64 in. 1-1/4 in. 12 11598 in. 2950 mm.
1-3/3 in. 6 11946 in. 1-13/64 in. 1-3/8 in. 12 12848 in. 1290 in.
1-1/2 in. 6 13196 in. 1-21/64 in. 1-1J2in. 12 14098 in. 3600 rnm.
1-3/4 in. 5 15335 in. 1-35/64 in.
2 in. 4-1/2 17594 in. 1-25/32 in.
en
ClassicBike.biz
Printed in Ene/and by
WARWICK PRINTING COMPANY LIMITED
WARWICK
ClassicBike.biz
ClassicBike.biz

Triumph Repair Manual 63 70

Uploaded by

Copyright:

Available Formats

Triumph Repair Manual 63 70

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Triumph Repair Manual 63 70

Uploaded by

Copyright:

Available Formats

What is the document about?

What type of motorcycle is discussed?

WORKSHOP MANUAL

UNIT CONSTRUCTION 650 C.c. TWINS

You might also like