Julia Kathrin Siebeck

Inspector Wilmer here with a quick and handy electrical tip! Did you know your trusty little sniffer tool- a non-contact voltage detector-can do more than you think? If you don’t have one yet, it’s time to get this essential tool in your kit. #ElectricalTips #InspectorWilmer #HomeInspection #WaypointPropertyInspection

2

SR3 security shutters - British manufactured LPS1175 security shutters Security Rating 3 is classified as medium commercial risk. SR3 has significant increase in security grade with the commensurate increase in weight and strength. These SR3 security shutters are tested and provide resistance to tools in Category A & B (as specified for SR2) plus C (below). The tools of this category is for deliberate forced entry of well-protected premises using bodily physical force and a wide selection of attack options. Attack time: The maximum attack time is 5 minutes. The maximum test duration is 20 minutes Tools category A, B plus C: Axe, battery, bolt cutter, brick bolster, cold chisel, crowbar, drill, fluorocarbon based freeze spray, gas torch, hacksaw, hammer, pad saw, scissor jack, wood chisel Lock/hardware standard: BS EN 1303 class 4. Building hardware. Cylinders for locks. Requirements and test methods.

3

When installing sectional doors, incorrect positioning of a pusher spring can be a major problem. Here’s a guide on how to set a pusher spring on both manual and electrically operated sectional overhead doors… https://lnkd.in/eczeJAuB #PusherSpring #SectionalOverheadDoor

4

There are five fire safety tactics available to the architect/ FLS Engineers/Fire Protection Engineers seeking to fulfil the objectives of life safety and property protection : ☛ Prevention – ensuring that fires do not start by controlling and fuel sources. ☛ Communication – ensuring that if ignition occurs, the occupants are informed and any active fire safety systems are initiated. ☛ Escape – ensuring the occupants of the building and the surrounding areas can move to a place of safety before they are threatened by the smoke and heat. ☛ Containment – ensuring that the fire is contained to the smallest possible area limiting the amount of property likely to be damaged. ☛ Extinguishment – ensuring that the fire can be extinguished quickly and with minimal consequential damage to the old building.

5

Safety Equipment Checks: A common issue that we encounter in the AED industry is "Dead" or "Expired" equipment. Unmaintained AEDs or failure to update the expiring accessories can lead to an AED that does not operate properly. In many cases, the AED is inoperable and the possible deployers of the AED are not aware until the emergency happens. The AED manufacturers recommended and routinely scheduled AED service can solve this issue. AEDs require updates, expiration replacements and cleaning on a regular schedule. Does your business or facility require AED Maintenance and Scheduled AED Service? Contact us, Public Safety Training & Supply, we can assist!

1

Did you see our spotlight recently about the Gas and Vapours (Ex01- Ex04) qualification? Want to know more? Take a look below 👇

40

Do you know what it takes to achieve Red Seal certification? The Red Seal designation is awarded to people who pass the Red Seal exam, which is meant to test the skill of a tradesperson after they’ve completed their years of training. This designation not only shows that a person knows their trade inside and out; they also have a national certification that will open doors to employment across Canada. Achieving this goal takes a lot of work, though! First, you’ll have to begin your trades training – this can be done through one of Ontario’s colleges. If you’re curious about Red Seal trades, or how to begin your skilled trades journey, visit https://ow.ly/EsIW50TUOEo and learn more!

3

Is this ENERGIZED WORK? Here is the story... -- You are a generator technician . You've been called to a customer's site because they can't get their Automatic Transfer Switch (ATS) to operate. After some careful investigation and troubleshooting you discover the control panel needs to be replaced. In order to replace it you will need to open the door to the ATS and expose yourself to 600 volts. The control panel is on the door that you opened. You ask the client if you can kill power to the ATS while you work but they say NO! Now what do you do? Can you still complete the task safely? Is this considered energized work? Do you need an energized work permit? Let me know what you think! -- Want to learn more about energized work? Take a look here https://buff.ly/3vJxjA7 #electricalsafety #electricians #arcflash

1

4 Kommentare

🔍 Do you have a shortage of technicians or a productivity challenge? Recently, it became clear that what appeared to be a staffing shortage was actually a productivity issue. Low billable hours were driven by non-client-facing tasks that burdened technical staff. By focusing on improving productivity, many organisations find they don’t need more technicians after all. Interested in how this strategy can work for you? Check out our blog linked in the comments for effective solutions that can benefit any organisation facing similar challenges! #WorkforceOptimization #ProductivityBoost #TeamEfficiency #StaffUtilization #BusinessPerformance #WorkforceManagement #BusinessGrowth #OperationalExcellence #TechnicalStaff #PeopleStrategy #MaximizeEfficiency #EmployeeProductivity #UtilizationMatters #BusinessSuccess

1

1 Kommentar

For owners of storage equipment, knowing how to find the correct information for your system can be confusing. That’s why our SEMA Technical Committee has created a library of documents which help guide you on your racking and ensure you tick the boxes when meeting HSE health and safety requirements. These documents are not just for engineers and racking suppliers and there is information relevant to anyone who uses racking. Even better, work with one of our SEMA members and you will automatically know they are working to these standards. #SEMA #TechnicalCommittee #WarehouseRackingGuidance https://lnkd.in/e_xwXkXr

15

1 Kommentar

How does the NTA choose NEET-UG exam centres? Key requirements include proper seating, lighting, ventilation, security, and accessibility. Centres cannot be run by coaching institutes to avoid conflicts of interest. A 3rd-party review of a sample of the exam centres where NEET-UG was conducted on May 5 found issues, such as missing CCTVs and unguarded strong rooms. Click on the 🔗 below to read how the NTA selects exam centres for NEET-UG and the gaps revealed in a recent review 👇🏽 https://lnkd.in/g3fH7iai

12

Overview of Work Permit System More:- https://lnkd.in/dknzD-8 https://lnkd.in/dknzD-8

1

Overview of Work Permit System More:- https://lnkd.in/dknzD-8 https://lnkd.in/dknzD-8

9

Overview of Work Permit System More:- https://lnkd.in/dknzD-8 https://lnkd.in/dknzD-8

8

Overview of Work Permit System More:- https://lnkd.in/dknzD-8 https://lnkd.in/dknzD-8

6