EE8403 Notes PDF

EE8403 - MI Visit & Downloaded From : www.LearnEngineering.
in
www.rejinpaul.com
ENGINEERING COLLEGES
2016 – 17 Even Semester
COMMON MINIMUM STUDY MATERIAL (MSM)
Department of EEE
SUBJECT CODE: EE 6404
SUBJECT NAME: MEASUREMENTS AND INSTRUMENTATION
Regulation: 2013 Year and Semester: II/IV
Prepared by
DEPARTMENT OF EEE
Sl. No. Name of the Faculty Designation Affiliating College
SUBJECT
1 CODE: EE 8PRAVIN
S. EBANEZER 403 AP SCADCET
SUBJECT
2 NAME: MEASUREMENTS AND
D. JUSTIN LIVINGSTON AP INSTRUMENTATION
MTEC
3 L. ARUN
REGULATION : ANTONY
R2017XAVIER AP FXEC
4
YEAR R.KESAVA
AND SEM: PRABU
II/IV AP FXEC
5 J.Y. ANGELINE JEMINA AP SCADEC
Verified by DLI, CLI and Approved by the Centralized Monitoring Team dated
downloaded from www.rejinpaul.com

Visit & Downloaded From : www.LearnEngineering.in
1
EE8403 - MI Visit & Downloaded From : www.LearnEngineering.in
EE 8403 www.rejinpaul.com
MEASUREMENT AND INSTRUMENTATION LTPC
3 0 0 3
UNIT I INTRODUCTION 9
Functional elements of an instrument – Static and dynamic characteristics – Errors in

measurement – Statistical evaluation of measurement data – Standards and calibration.
UNIT II ELECTRICAL AND ELECTRONICS INSTRUMENTS 9
Principle and types of analog and digital voltmeters, ammeters, multi meters – Single and
three phase watt meters and energy meters – Magnetic measurements – Determination of
B-H curve and measurements of iron loss – Instrument transformers – Instruments for
measurement of frequency and phase.
UNIT III COMPARISON METHODS OF MEASUREMENTS 9
DC and AC potentiometers, DC and AC bridges, transformer ratio bridges, self-balancing

bridges, Interference and screening – Multiple earth and earth loops – Electrostatic and
electromagnetic interference – Grounding techniques.
UNIT IV STORAGE AND DISPLAY DEVICES 9
Magnetic disk and tape – Recorders, digital plotters and printers – CRT display – Digital
CRO – LED, LCD and dot matrix display – Data loggers.
UNIT V TRANSDUCERS AND DATA ACQUISITION SYSTEMS 9
Classification of transducers – Selection of transducers – Resistive, inductive and

capacitive transducers – Piezo-electric, optical and digital transducers – Elements of data
acquisition system – A/D, D/A converters – Smart sensors.
Total Hours:45
TEXT BOOKS:
1. A.K. Sawhney, ‘A Course in Electrical & Electronic Measurements &
Instrumentation’,Dhanpat Rai and Co, 2004.
2. J. B. Gupta, ‘A Course in Electronic and Electrical Measurements’, S. K. Kataria &
Sons,Delhi,2003.
3. Doebelin E.O. and Manik D.N., Measurement Systems – Applications and Design,
Special Indian Edition, Tata McGraw Hill Education Pvt. Ltd., 2007.
REFERENCES:
1. H.S. Kalsi, ‘Electronic Instrumentation’, Tata McGraw Hill, II Edition 2004.
2. D.V.S. Moorthy, ‘Transducers and Instrumentation’, Prentice Hall of India Pvt Ltd,
2007.
3. A.J. Bouwens, ‘Digital Instrumentation’, Tata McGraw Hill, 1997.
4. Martin Reissland, ‘Electrical Measurements’, New Age International (P) Ltd., Delhi,
2001.
5. Alan. S. Morris, Principles of Measurements and Instrumentation, 2nd Edition, Prentice
Hall of India, 2003.
2
AIM www.rejinpaul.com
 To provide clear knowledge of the basic laws governing the operation of
instrument, relevant circuits, error, calibration etc.
 Elaborate discussion on storage and display devices, transducers and Data
Acquisition systems.
IMPORTANCE AND NEED OF SUBJECT
 To understand the physical principles of electrical and electronics based

measurements.
 There is a strong emphasis on electronics, from fundamentals of analogue and
digital circuits to complex components and systems constructed from them.
 It is essential to know, how a range of typical sensor do operate.
COURSE OUTCOME (CO)
 Understand that there are finite limits to our ability to make good measurements.
 Able to apply basic physics to real problems.
 Acquire theoretical knowledge directly applicable to laboratory work.
 Acquire theoretical knowledge directly applicable to laboratory work.
 Be able to categorize different sensors used in various applications.
LATEST DEVELOPMENTS
 A combined support vector machine –wavelet transform model for prediction of

sediment transport in sewer.
 Industrial tomography using three different gamma rays.
CONTENT BEYOND SYLLABUS
 Pneumatic transducer
 Pyrometers
INDUSTRIAL CONNECTIVITY
 Nagman Instruments and Electronics (P) Ltd, Chennai.

 SKITECH Automation, Chennai.

3
DETAILED LESSON PLAN www.rejinpaul.com

Name of the subject and code: EE8403& MEASUREMENT AND INSTRUMENTATION
TEXT BOOKS:
1. A.K. Sawhney, ‘A Course in Electrical & Electronic Measurements &
Instrumentation’,Dhanpat Rai and Co, 2004.
2. J. B. Gupta, ‘A Course in Electronic and Electrical Measurements’, S. K. Kataria &
Sons,Delhi,2003.
3. Doebelin E.O. and Manik D.N., Measurement Systems – Applications and Design,
Special Indian Edition, Tata McGraw Hill Education Pvt. Ltd., 2007.
REFERENCES:
1. H.S. Kalsi, ‘Electronic Instrumentation’, Tata McGraw Hill, II Edition 2004.
2. D.V.S. Moorthy, ‘Transducers and Instrumentation’, Prentice Hall of India Pvt Ltd, 2007.
3. A.J. Bouwens, ‘Digital Instrumentation’, Tata McGraw Hill, 1997.
4. Martin Reissland, ‘Electrical Measurements’, New Age International (P) Ltd., Delhi, 2001.
5. Alan. S. Morris, Principles of Measurements and Instrumentation, 2nd Edition, Prentice Hall
of India, 2003.
Hours Cumm
Unit Requir ulative
Topic T or R
No. ed/Plan Hrs
ned
Functional elements of an instrument 1 1 T1
Static characteristics 2 3 T1
T3
Dynamic characteristics 2 5 T1
T3
UNIT I
Errors in measurement 1 6 T1
T2
Statistical evaluation of measurement data 1 7 T1
Standards 1 8 T1
Calibration 1 9 T1
Principle of analog & digital voltmeters, ammeters 2 11 T1

Multi meter – Analog & Digital 1 12 T1
Single phase watt meters 1 13 T1
three phase watt meters T2
Energy meters - Principle of operation, construction and 1 14 T1
UNIT working T2
II Magnetic measurements - Determination of B-H curve – 1 15 T1
Problems T2
Measurement of iron loss 1 16 T1
T2
Instrument Transformers - Types 1 17 T1
T2
Instruments for measurement of frequency and phase 1 18 T1
4
www.rejinpaul.com
1 19 T1
D.C potentiometers
T2
1 20 T1
A.C potentiometers
T2
D.C bridges 1 21 T3
1 22 T1
UNIT III A.C bridges
T2
Transformer ratio bridges 1 23 T1
Self-balancing bridges 1 24 T2
Interference and screening 1 25 T2
Multiple earth and earth loops & Grounding techniques. 1 26 T1
Electrostatic and electromagnetic interference 1 27 T2
Magnetic disk and tape Recorders 1 28 T1,T2
Digital plotters 1 29 T3
Printers 1 30 T3
CRT display 1 31 T1
UNIT 1 32 T1,T2
Digital CRO
IV
2 34 T1
LED,LCD
Dot matrix display 1 35 T1
Data loggers 1 36 T1
Classification & Selection of transducers 1 37 T1,T2
Resistive transducers 1 38 T1
Capacitive transducers 1 39 T1
1 40 T1
Inductive transducer
T2
Piezoelectric transducers 1 41 T1
UNIT V
Optical transducers 1 42 T1
1 43 T1
Digital transducers
T3
Elements of data acquisition system 1 44 T1
A/D converters 1 45 T1
D/A converters, Smart sensor 1 46 T1

5
TABLE OF CONTENTS www.rejinpaul.com

Sl No Unit No Topic/Title Page No
1 Part - A 8
2 Functional elements of Measurement system 9
3 Static characteristics of Measurement system 10
4 Calibration 12
5 I Standard 14
6 Dynamic charecteristics 15
7 Problem on statistical evaluation 16
8 Errors in measurement 16
9 Statistical evaluation of measurement data 19
10 Part - A 21
11 Moving iron instrument 22
12 Instrument transformer 24
13 B-H curve 25
14 II Digital voltmeter 27
15 Energy meter 29
16 Measurement of frequency 30
17 Electrodynamometer type instrument 33
18 PMMC Instrument 36
19 Selection of voltmeter 38
20 Digital multimeter 39
21 Part A 40
22 Maxwell’s Bridge 41
23 Schering’s Bridge 43
24 III Electrostatic and electromagnetic interference 44
25 DC potentiometer 45
26 AC potentiometer 47
27 Earthing techniques 49
28 Hay’s bridge 51
29 Wheatstone bridge 53
30 Part A 55
31 Parts of CRT 56
32 Applications of LCD 58
33 IV Types of recording 60
34 Digital CRO 63
35 X-Y recorder 64
36 Data logger 65
37 Digital plotters and printers 66
38 Magnetic tape recording 69
39 Compare LCD & LED 72
40 LCD 73
41 Part A 75
42 Classifications and characteristics of transducer 76
43 RTD and thermistor 79
44 LVDT 82
45 V DAS (Data Acquisition System) 83
46 Piezo electric transducer 87
6
47 Smart sensors www.rejinpaul.com

88
48 A/D 92
49 D/A 93
50 Characteristics and selection of transducers 94

7
UNIT I www.rejinpaul.com
INTRODUCTION
PART-A
1. What is standard? What are the different types of standards? (MAY 2008/MAY
2009/MAY 2011)
A standard is a physical representation of a unit of measurement. A known
accurate measure of physical quantity is termed as standard. Types are International
standard, primary standard, secondary standard and working standard.
2. Define calibration.(NOV/DEC 2010)
Calibration is the process of checking the accuracy of instrument comparing the
instrument reading with a standard against a similar meter of known accuracy.
3. Define static error and how is it classified?(NOV 2009)
The static error of a measuring system is the numerical difference between the
true value of a quantity and its value as obtained by measurement. The various types are
gross error, systematic error and random error.
4. What are the various important functional elements of a typical measurement
system? (Apr / May 13)
Primary sensing element
Variable conversion element
Variable manipulation element
Data transmission element
Data presentation element
5. Illustrate the difference between precision and accuracy. (Apr / May 15)
Accuracy Precision
Accuracy refers to the degree of closeness Precision refers to the degree of agreement
or conformity to the true value of within a group of measurements and
quantity under measurement where the true instruments or reproducibility of the value
value is the ideal value
Accuracy gives the maximum error which is Precision of a measuring system gives its
maximum departure of the final result from capability to reproduce a certain reading
its true value with a given accuracy
6. Give the international standards of instruments. (Apr / May 14)
International Ohms
International Amperes
8
7. What is drift? (Nov/Dec 2011) www.rejinpaul.com

It is the variation of the measured value with time. Perfect reproducibility means that the
instrument has no drift.
8. The expected value of the voltage across a resistor is 40 volt, however the
measurement gives a value of 39 volt. Calculate the absolute error. (May/June
2013)
Absolute error e= At-Am=40-39=1volt
9. Define limiting errors. (Dec 2007)\
Instruments having analog meters are usually guaranteed to be accurate within certain
percentage limits called limiting errors or Guarantee errors.
10. Define dynamic characteristics of instrument. (Dec 2008)
The behavior of instrument when inputs vary with time and do the output.
11. Define fidelity (Nov 2009)
It is determined by the fact that how closely the instrument reading follows the measured
variable. i.e. It is the degree to which an instrument indicates the changes in measured
variable without dynamic error.
12. What are the static characteristics of instrument? (May 2008)
Static characteristics of instrument are used to measure unvarying processes of the
instrument. The main static characteristics are accuracy, resolution, precision, drift, static
error, dead zone etc.
PART-B
1. Explain the functional elements of measurement system with neat block

diagram.(DEC 14)
Most of the measurement systems contain three main functional elements. They are:
i) Primary sensing element
ii) Variable conversion element &
iii) Data presentation element.
Primary Variable Variable Data

sensing manipulatio conversion presentation
element n element element element

9
Primary sensing element: www.rejinpaul.com

The quantity under measurement makes its first contact with the primary sensing
element of a measurement system. i.e., the measurand- (the unknown quantity which is
to be measured) is first detected by primary sensor which gives the output in a different
analogous form This output is then converted into an e electrical signal by a transducer -
(which converts energy from one form to another). The first stage of a measurement
system is known as a detector transducer stage’.
Variable conversion element:
The output of the primary sensing element may be electrical signal of any form, it may be
voltage, a frequency or some other electrical parameter For the instrument to perform the
desired function, it may be necessary to convert this output to some other suitable form.
Variable manipulation element:
The function of this element is to manipulate the signal presented to it preserving the
original nature of the signal. It is not necessary that a variable manipulation element
should follow the variable conversion element Some non -linear processes like
modulation, detection, sampling , filtering, chopping etc., are performed on the signal to
bring it to the desired form to be accepted by the next stage of measurement system
This process of conversion is called μ signal conditioning’
Data presentation element:
The information about the quantity under measurement has to be conveyed to the
personnel handling the instrument or the system for monitoring, control, or analysis
purposes. This function is done by data presentation element. In case data is to be
monitored, visual display devices are needed. These devices may be analog or digital
indicating instruments like ammeters, voltmeters etc. In case data is to be recorded,
recorders like magnetic tapes, high speed camera & TV equipment, CRT, printers may
be used. The final stage in a measurement system is known as terminating stage’.
2. Explain the static characteristics of measurement system in detail.(APR

2011/MAY 2013) The set of criteria defined for the instruments, which are used to
measure the quantities which are slowly varying with time or mostly constant, i.e., do not
vary with time, is called ‘static characteristics’.
The various static characteristics are:
i) Accuracy
ii) Precision

10
iii) Sensitivity www.rejinpaul.com

iv) Linearity
v) Reproducibility
vi) Repeatability
vii) Resolution
viii) Threshold
ix) Drift
x) Stability
xi) Tolerance
xii) Range or span
Accuracy:
It is the degree of closeness with which the reading approaches the true value of the
quantity to be measured.
Precision:
It is the measure of reproducibility i.e., given a fixed value of a quantity, precision is a
measure of the degree of agreement within a group of measurements. The precision is
composed of two characteristics:
a) Conformity:
Consider a resistor having true value as 2385692, which is being measured by an
ohmmeter. But the reader can read consistently, a value as 2.4 M due to the non
availability of proper scale. The error created due to the limitation of the scale reading is
a precision error.
b) Number of significant figures:
The precision of the measurement is obtained from the number of significant figures, in
which the reading is expressed. The significant figures convey the actual information
about the magnitude & the measurement precision of the quantity.
Sensitivity:
The sensitivity denotes the smallest change in the measured variable to which the
instrument responds. It is defined as the ratio of the changes in the output of an
instrument to a change in the value of the quantity to be measured.
Linearity:
The linearity is defined as the ability to reproduce the input characteristics symmetrically
& linearly.
Reproducibility:

11
It is the degree of closeness with which a given value may www.rejinpaul.com

be repeatedly measured. It is
specified in terms of scale readings over a given period of time.
Repeatability:
It is defined as the variation of scale reading & random in nature.
Drift:
Drift may be classified into three categories:
a) Zero drift:
If the whole calibration gradually shifts due to slippage, permanent set, or due to undue
warming up of electronic tube circuits, zero drift sets in.
b) Span drift or sensitivity drift:
If there is proportional change in the indication all along the upward scale, the drifts is
called span drift or sensitivity drift.
c) Zonal drift:
In case the drift occur only a portion of span of an instrument, it is called zonal drift.
Resolution:
If the input is slowly increased from some arbitrary input value, it will again be found that
output does not change at all until a certain increment is exceeded. This increment is
called resolution.
Threshold:
If the instrument input is increased very gradually from zero there will be some minimum
value below which no output change can be detected. This minimum value defines the
threshold of the instrument.
Stability:
It is the ability of an instrument to retain its performance throughout is specified operating
life.
Tolerance:
The maximum allowable error in the measurement is specified in terms of some value
which is called tolerance.
Range or span:
The minimum & maximum value of a quantity for which an instrument is designed to
measure is called its range or span.
3. With a suitable illustration elaborate the significance of

calibrations.(APR/MAY14)

12
 www.rejinpaul.com
Calibration is the process of making an adjustment or marking a scale so that the
readings of an instrument agree with the accepted & the certified standard.
 In other words, it is the procedure for determining the correct values of measurand
by comparison with the measured or standard ones.
 The calibration offers a guarantee to the device or instrument that it is operating
with required accuracy, under stipulated environmental conditions.
 The calibration procedure involves the steps like visual inspection for various
defects, installation according to the specifications, zero adjustment etc.,
 The calibration is the procedure for determining the correct values of measurand
by comparison with standard ones.
 The standard of device with which comparison is made is called a standard
instrument. The instrument which is unknown & is to be calibrated is called test
instrument.
 Thus in calibration, test instrument is compared with standard instrument.
Types of calibration methodologies:
There are two methodologies for obtaining the comparison between test instrument &
standard instrument. These methodologies are
i) Direct comparisons
ii) Indirect comparisons
Direct comparisons:
 In a direct comparison, a source or generator applies a known input to the meter
under test.
 The ratio of what meter is indicating & the known generator values gives the
meters error.
 In such case the meter is the test instrument while the generator is the standard
instrument.
 The deviation of meter from the standard value is compared with the allowable
performance limit.
 With the help of direct comparison a generator or source also can be calibrated.
Indirect comparisons:
 In the indirect comparison, the test instrument is compared with the response
standard instrument of same type i .e., if test instrument is meter, standard instrument
is also meter, if test instrument is generator; the standard instrument is also generator &

13
www.rejinpaul.com
so on. If the test instrument is a meter then the same input is applied to the test meter
as well a standard meter.
 In case of generator calibration, the output of the generator tester as well as
standard, or set to same nominal levels. Then the transfer meter is used which
measures the outputs of both standard and test generator.
4. Discuss the different types of standards of measurements (Apr/May 15)
Standard
All the instruments are calibrated at the time of manufacturer against measurement
standards. A standard of measurement is a physical representation of a unit of
measurement. A standard means known accurate measure of physical quantity.
The different size of standards of measurement are classified as
 International standards
 Primary standards
 Secondary standards
 Working standards
International standards
 International standards are defined as the international agreement. These
standards, as mentioned above are maintained at the international bureau of weights an
d measures and are periodically evaluated and checked by absolute measurements in
term s of fundamental units of physics.
 These international standards are not available to the ordinary users for the
calibration purpose.
 For the improvements in the accuracy of absolute measurements the international
units are replaced by the absolute units in 1948. Absolute units are more accurate than
the international units.
Primary standards
 These are highly accurate absolute standards, which can be used as ultimate
reference standards. These primary standards are maintained at national standard
laboratories in different countries.
 These standards representing fundamental units as well as some electrical and
mechanical derived units are calibrated independently by absolute measurements at
each of the national laboratories.

14
 www.rejinpaul.com
These are not available for use, outside the national laboratories. The main
function of the primary standards is the calibration and verification of secondary
standards.
Secondary standards
 As mentioned above, the primary standards are not available for use outside the
national laboratories. The various industries need some reference standards.
 So, to protect highly accurate primary standards the secondary standards are
maintained, which are designed and constructed from the absolute standards.
 These are used by the measurement and calibration laboratories in industries and
are maintained by the particular industry to which they belong. Each industry has its
own standards.
Working standards
These are the basic tools of a measurement laboratory and are used to check and
calibrate the instruments used in laboratory for accuracy and the performance.
5.A) i) Explain the dynamic characteristics of measurement system in detail.( MAY

2013)
Dynamic characteristics: The set of criteria defined for the instruments, which are
changes rapidly with time, is called ‘dynamic characteristics’.
The various static characteristics are: i) Speed of response ii)Measuring lag iii) Fidelity
iv) Dynamic error
Speed of response: It is defined as the rapidity with which a measurement system
responds to changes in the measured quantity.
Measuring lag: It is the retardation or delay in the response of a measurement system
to changes in the measured quantity. The measuring lags are of two types: a)
Retardation type: In this case the response of the measurement system begins
immediately after the change in measured quantity has occurred. b) Time delay lag: In
15
this case the response of the measurement system beginswww.rejinpaul.com

after a dead time after the
application of the input.
Fidelity: It is defined as the degree to which a measurement system indicates changes
in the measurand quantity without dynamic error.
Dynamic error: It is the difference between the true value of the quantity changing with
time & the value indicated by the measurement system if no static error is assumed. It is
also called measurement error.
ii) A circuit was tuned for resonance by eight different students and the values of
resonant frequency in KHz were recorded as 532, 548, 543, 535, 546, 531, 543, and
536. Calculate a) Mean b) Average deviation
a) Mean = (532+548+ 543+ 535+ 546+ 531+ 543+ 536)/8

= 4314/8
= 539.25
b) SD:
Deviation from meanD1 = 532-539.25 = -7.25
D2 = 548-539.25= 8.75
D3 = 543-539.25= 3.75
D4= 535-539.25= -4.25
D5= 546-539.25=6.75
D6= 531-539.25= -8.25
D7= 543-539.25=3.75
D8= 536-539.25= -3.25
Average deviation = (7.25+8.75+3.75+4.25+6.75+8.25+3.75+3.25) /8
= 46/8
= 5.75
PART C(15 Mark)

1. Classify and explain the different errors of measurements. (Nov/Dec 14)
The types of errors are follows
i) Gross errors
ii) Systematic errors
iii) Random errors
Gross Errors:

16
www.rejinpaul.com
The gross errors mainly occur due to carelessness or lack of experience of a human
being.These errors also occur due to incorrect adjustments of instruments. These errors
cannot be treated mathematically. These errors are also called personal errors.
Ways to minimize gross errors:
The complete elimination of gross errors is not possible but one can minimize them by
the following ways:
 Taking great care while taking the reading, recording the reading & calculating the
result.
 Without depending on only one reading, at least three or more readings must be
taken preferably by different persons.
Systematic errors:
A constant uniform deviation of the operation of an instrument is known as a
Systematic error. The Systematic errors are mainly due to the short comings of the
instrument & thecharacteristics of the material use d in the instrument, such as defective
or worn parts, ageing effects, environmental effects, etc.
Types of Systematic errors:
There are three types of Systematic errors as:
i) Instrumental errors
ii) Environmental errors iii) Observational errors
Instrumental errors:
These errors can be mainly due to the following three reasons:
a) Short comings of instruments:
These are because of the mechanical structure of the instruments. For example friction
in the bearings of various moving parts; irregular spring tensions, reductions in due to
improper handling , hysteresis, gear backlash, stretching of spring, variations in air gap,
etc .,
Ways to minimize this error:
These errors can be avoided by the following methods:
Selecting a proper instrument and planning the proper procedure for the measurement
recognizing the effect of such errors and applying the proper correction factors
calibrating the instrument carefully against a standard
b) Misuse of instruments:
A good instrument if used in abnormal way gives misleading results. Poor initial
adjustment, Improper zero setting, using leads of high resistance etc., are the examples
17
www.rejinpaul.com
of misusing a good instrument. Such things do not cause the permanent damage to the
instruments but definitely cause the serious errors.
c) Loading effects
Loading effects due to im proper way of using the instrument cause the serious errors.
The best ex ample of such loading effect error is connecting a w ell calibrated volt meter
across the two points of high resistance circuit. The same volt meter connected in a low
resistance circuit gives accurate reading.
Thus the errors due to the loading effect can be avoided by using an instrument
intelligently and correctly.
Environmental errors:
These errors are due to the conditions external to the measuring instrument. The various
factors resulting these environmental errors are temperature changes, pressure
changes, thermal emf, ageing of equipment and frequency sensitivity of an instrument.
The various methods which can be used to reduce these errors are:
i) Using the proper correction factors and using the information supplied by the
manufacturer of the instrument
ii) Using the arrangement which will keep the surrounding conditions Constant
iii) Reducing the effect of dust, humidity on the components by hermetically sealing the
components in the instruments
iv)The effects of external fields can be minimized by using the magnetic or electrostatic
shields or screens
v) Using the equipment which is immune to such environmental effects.
Observational errors:
These are the errors introduced by the observer. These are many sources of
observational errors such as parallax error while reading a meter, wrong scale selection,
etc.
Ways to minimize this error
To eliminate such errors one should use the instruments with mirrors, knife edged
pointers, etc.,
The systematic errors can be subdivided as static and dynamic errors. The static errors
are caused by the limitations of the measuring device while the dynamic errors are

18
www.rejinpaul.com
caused by the instrument not responding fast enough to follow the changes in the
variable to be measured.
Random errors:
Some errors still result, though the systematic and instrumental errors are reduced or
atleast accounted for. The causes of such errors are unknown and hence the errors are
called random errors.
Ways to minimize this error
The only way to reduce these errors is by increasing the number of observations and
using the statistical methods to obtain the best approximation of the reading.
2. Explain the concept of static evaluation of measurement data? (8)(April/may
2011) (OR) How is the statistical analysis of measurement data form performed?
(May/June 2013)
STATISTICAL EVALUATION OF MEASUREMENT DATA

Out of the various possible errors, the random errors cannot be determined in the
ordinary process of measurements. Such errors are treated mathematically the
mathematical analysis of the various measurements is called statistical analysis of the
data’.
For such statistical analysis, the same reading is taken number of times, generally u
sing different observers, different instruments & by different ways of measurement. The
statistical anlysis helps to determine analytically the uncertainty of the final test results.
Arithmetic mean& median: When the n umber of readings of the same measurement
are taken, the most likely value from the set of measured value is the arithmetic mean of
the number of readings taken. The arithmetic mean value can be mathematically
obtained as,
This mean is very close to true value, if number of readings is very large. But when the
number of readings is large, calculation of mean value is complicated.
In such a case, a median value is obtained which is obtained which is a close
approximation to the arithmetic mean value. For a set of Qmeasurements X1, X2, X3.
Xn written down in the ascending order of magnitudes, the median value is given by,
Xmedian=X (n+1)/2

19
Average deviation: www.rejinpaul.com

The deviation tells us about the departure of a given reading from the arithmetic mean
of the data set di=xi- ¯X
Where di = deviation of ith reading Xi= value of ith reading
¯X = arithmetic mean The average deviation is defined as the sum of the absolute
values of deviations divided by the number of readings. This is also called mean
deviation
Standard Deviation:
The standard deviation, or root mean square deviation of a sample is both
mathematically more convenient and statistically more meaningful for analyzing grouped
data than is the average deviation. By definition, the standard deviation of a sample is
given by
Variance:
It is the mean square deviation, which is the same as standard deviation, except
that square root is not extracted.
V=(standard deviation)2
=d12+ d12+ d12+……. d12/n
=∑d2/n
When the number of observations is less than 20,
Variance V=∑d2
n –1

20
UNIT II www.rejinpaul.com
ELECTRICAL AND ELECTRONIC INSTRUMENTS
PART-A
1.What is creeping in energy meter? How it is prevented?(MAY/JUN 2012)
A slow but continuous rotation of the energy meter disc system even when there is no
current flowing though the coil but only the pressure coil is energized is called as
creeping. It can be prevented by drilling two diametrically opposite holes in the disc
which makes the disc comes to rest with one of the holes under the edge of a pole of the
shunt magnet.
2.Why the PMMC instruments are not used for AC measurements?(NOV/DEC 14)
When the PMMC instruments are connected to AAC, the torque reverses as the current
reverses and the pointer cannot follow the rapid reversals. Hence the deflection
corresponding to mean torque is zero thus making the PMMC instrument not suitable for
AC measurements.
3.Which torque is absent in energy meter? Why?(NOV 2009)
In energy meter, there is no controlling torque, as the driving torques is enough to
cause continuous revolution of the disc.
4.State the purpose of shunts in the voltmeter (APR/MAY 11)
When an ammeter is needed to measure currents of having large magnitudes a
proportion of the current is diverted through a low value resistance connected in parallel
with the meter. Such a diverting type of resistor is referred to as shunt. The milli ammeter
is converted into voltmeter by connecting a resister series with the meter called
multiplier.
5.Classify different types of iron loss. (APR/MAY 11)
 Eddy current
 Hysteresis losses
6.Explain with example the term hysteresis. (Nov/Dec 12)
Hysterisis is the phenomenon which depicts different output effects when loading and
unloading in any system, whether it is a electrical system or a mechanical system.
7.How does one extend the range of ammeter and voltmeter? (Nov/Dec 2011)
Voltmeter is extended by adding resistance in series with it whereas ammeter is
extended by connecting resistance in parallel with it.

21
8.How we do the ballistic test? (Nov/Dec 2011) www.rejinpaul.com

These tests are generally employed for the determination of B- H curves and hysteresis
loops of Ferro-magnetic materials.
9.Draw the circuit of a basic dc voltmeter. (May/June 2013)
10.What are the different types of torque produced in PMMC instrument?(Dec

2009)
 Deflection torque
 Controlling Torque
 Damping Torque
11.What are the advantages of digital multimeter?
 Highly accurate
 Loading effect is Nil
 Easily portable
 Very Cheap
 Easy to interface
12.Why ordinary watt meters are not suitable in places of LPF circuits? (Dec 2010)
 The deflecting torque is very small due to low power factor
 Errors due to induction coil is large due to low power factor
PART-B
1.(i)Explain the moving iron instrument in detail with neat sketch.(NOV/DEC 14)
Classification of Moving Iron Instruments

Moving iron instruments are of two types
(i) Attraction type. (ii) Repulsion type.
Attraction Type
22
The coil is flat and has a narrow slot like opening. The moving iron is a flat disc or
a sector eccentrically mounted.
 When the current flows through the coil, a magnetic field is produced and the
moving iron moves from the weaker field outside the coil to the stronger field inside it or
in other words the moving iron is attracted in.
 The controlling torque is provided by springs hut gravity control can be used for
panel type of instruments which are vertically mounted. Damping is provided by air
friction with the help of a light aluminium piston (attached to the moving system) which
move in a fixed chamber closed at one end.
Repulsion Type
In the repulsion type, there are two vanes inside the coil one fixed and other movable.
These are similarly magnetized when the current flows through the coil and there is a
force of repulsion between the two vane s resulting in the movement of the moving vane.
Two different designs are in common use
(I) Radial Vane Type

In this type, the vanes are radial strips of iron. The fixed vane is attached to the coil and
the movable one to the spindle of the instrument.
(a) Radial vane type (b) Co-axial vane type

23
www.rejinpaul.com
ii) Co-axial Vane Type
 In this type of instrument, the fixed and moving vanes are sections of co axial
cylinders as shown in Fig. The controlling torque is provided by springs. Gravity control
can also be used in vertically mounted instruments.
 The damping torque is produced by air friction as in attraction type instruments.
The operating magnetic field in moving iron instruments is very weak and therefore eddy
current damping is not used in them as introduction of a permanent magnet required for
eddy current damping would destroy the operating magnetic field.
 It is clear that whatever may be the direction of the current in the coil of the
instrument, the iron vanes are so magnetized that there is always a force of attraction in
the attraction type and repulsion in the repulsion type of instruments. Thus moving iron
instruments are un-polarized instruments i.e., they are independent of the direction in
which the current passes.
(ii) Explain in detail the instrument transformer with neat sketch.(Nov/Dec 14)
Power measurements are made in high voltage circuits connecting the wattmeter to the
circuit through current and potential transformers as shown. The primary winding of the
C.T. is connected in series with the load and the secondary winding is connected in
series with an ammeter and the current coil of a wattmeter.
The primary winding of the potential transformer is connected across the supply lines
and a voltmeter and the potential coil circuit of the wattmeter are connected in parallel
with the secondary winding of the transformer. One secondary terminal of each
transformer and the casings are earthed.

24
www.rejinpaul.com
The errors in good modem instrument transformers are small and may be ignored for
many purposes. However, they must be considered in precision work. Also in some
power measurements these errors, if not taken into account, may lead to very inaccurate
results.
Voltmeters and ammeters are affected by only ratio errors while wattcmeters are
influenced in addition by phase angle errors. Corrections can be made for these errors if
test information is available about the instrument transformers and their burdens.
2) Obtain B-H curve of a ring specimen.(Apr/May14)

Method of reversals
 A ring shaped specimen whose dimensions are known is used for the purpose.
After demagnetizing the test is started by setting the magnetizing current to its lowest
test vane. With galvanometer key K closed, the iron specimen is brought into a ‘
reproducible cyclic magnetic state’ by throwing the reversing switch S backward and
forward about twenty times.
 Key K is now opened and the value of flux corresponding to this value of H is
measured by reversing the switch S and noting the throw of galvanometer. The value of
flux density corresponding to this H can be calculated by dividing the flux by the area of
the specimen. The above procedure is repeated for various values of H up to the
maximum testing point.
 The B-H curve may be plotted from the measured values of B corresponding to
the various values of H.
Step by step method

25
The circuit for this test is shown in Fig. The magnetizing winding is supplied
through a potential divider having a large number of tapping. The tapings are arranged
so that the magnetizing force H may be increased, in a number of suitable steps, up to
the desired maximum value.
 The specimen before being tested is demagnetized. The tapping switch S is set
on tapping I and the switch S is closed. The throw of the galvanometer corresponding to
this increase in flux density in the specimen, from zero to some value B, is observed.
Step by step method

After reaching the point of maximum H i.e... when switch S is at tapping 10, the
magnetizing current is next reduced, in steps to zero by moving switch 2 down through
the tapping points 9, 8, 7 3, 2, 1. After reduction of magnetizing force to zero, negative
values of H are obtained by reversing the supply to potential divider and then moving the
switch S up again in order 1, 2, 3 7, 8. 9, 10.
Method of reversals
This test is done by means of a number of steps, but the change in flux density
measured at each step is the change from the maximum value + Bm down to some
lower value. But before the next step is commenced the iron specimen is passed through
the remainder of the cycle of magnetization back to the flux density + Bm. Thus the cyclic
state of magnetization is preserved. The connections for the method of reversals are
shown in Fig.

26
www.rejinpaul.com
3) With a neat block diagram explain the construction and operating principle of
digital voltmeter. (8)(April/May 2011)
Digital Voltmeter
 A digital voltmeter (DVM) displays the value of a.c. or d.c. voltage being measured
directly as discrete numerals in the decimal number system. Numerical readout of
DVMs is advantageous since it eliminates observational errors committed by operators.
The errors on account of parallax and approximations are entirely eliminated.
 The use of digital voltmeters increases tile speed with which readings can be
taken. A digital voltmeter is a versatile and accurate voltmeter which has many
laboratory applications.
 On account of developments in the integrated circuit (IC) technology, it has been
possible to reduce the size, power requirements and cost of digital voltmeters. In fact,
for the same accuracy, a digital voltmeter now is less costly than its analog counterpart.
 The decrease in size of DVMs on account of use of ICs, the portability of the
instruments has increased.
 The unknown voltage is applied to the input of the integrator, and the output
voltage starts to rise. The slope of output voltage is determined by the value of input
27
www.rejinpaul.com
voltage This voltage is fed a level detector, and when voltage reaches a certain
reference level, the detector sends a pulse to the pulse generator gate. The level
detector is a device similar to a voltage comparator.
 The output voltage from integrator is compared with the fixed voltage of an
internal reference source, and, when voltage reaches that level, the detector produces
an output pulse.
 It is evident that greater then value of input voltage the sharper will be the slope of
output voltage and quicker the output voltage will reach its reference level. The output
pulse of the level detector opens the pulse level gate, permitting pulses from a fixed
frequency clock oscillator to pass through pulse generator.
 The basic block diagram of a typical integrating type of DVM is shown in Fig
 The generator is a device such as a Schmitt trigger that produces an output pulse
of fixed amplitude and width for every pulse it receives. This output pulse, whose
polarity is opposite to that of and has greater amplitude, is fed back of the input of the
integrator.
 Thus no more pulses from the clock oscillator can pass through to trigger the
pulse generator. When the output voltage pulse from the pulse generator has passed, is
restored to its original value and starts its rise again. When it reaches the level of
reference voltage again, the pulse generator gate is opened.
 The pulse generator is trigger by a pulse from the clock generator and the entire
cycle is repeated again. Thus, the waveform of is a saw tooth wave whose rise time is
dependent upon the value of output voltage and the fail time is determined by the width
of the output pulse from the pulse generator.
 Thus the frequency of the saw tooth wave is a function of the value of the voltage
being measured. Since one pulse from the pulse generator is produced for each cycle of
28
www.rejinpaul.com
the saw tooth wave, the number of pulses produced in a given time interval and hence
the frequency of saw tooth wave is an indication of the voltage being measured.
4. Describe the functional operation of energy meter. (8) (April/May 2011)
Construction of Induction Type Energy Meters: There are four main parts of the operating
mechanism.
(i) Driving system
(ii) Moving system
(iii) Braking system
(iv) Registering system
Driving system
 The driving system of the meter consists of two electro-magnets. The core of
these electromagnets is made up of silicon steel laminations. The coil of one of the
electromagnets is excited by the load current. This coil is called the current coil. The coil
of second electromagnet is connected across the supply and, therefore, carries a
current proportional to the supply voltage.
 This coil is called the pressure coil. Consequently the two electromagnets are
known as series and shunt magnets respectively.
 Copper shading bands are provided on the central limb. The position of these
bands is adjustable. The function of these bands is to bring the flux produced by the
shunt magnet exactly in quadrature with the applied voltage.
Moving System
 This consists of an aluminum disc mounted on a light alloy shaft. This disc is
positioned in the air gap between series and shunt magnets.
 The upper bearing of the rotor (moving system) is a steel pin located in a hole in
the bearing cap fixed to the top of the shaft. The rotor runs on a hardened steel pivot,
screwed to the foot of the shaft.
 The pivot is supported by a jewel bearing. A pinion engages the shaft with the
counting or registering mechanism.
Braking System
 A permanent magnet positioned near the edge of the aluminium disc forms the
braking system.
 The aluminium disc moves in the field of this magnet and thus provides a braking
torque. The position of the permanent magnet is adjustable, and therefore braking
29
torque can be adjusted by shifting the permanent magnet www.rejinpaul.com

to different radial positions as
explained earlier
Registering (counting) Mechanism
The function of a registering or counting mechanism is to record continuously a number

which is proportional to the revolutions made by the moving system. By a suitable
system, a train of reduction gears the pinion on the rotor shaft drives a series of five or
six pointers. These rotate on round dials which are marked with ten equal divisions.
5. What are the different methods used for the measurement of frequency? Explain
any one method(16)(NOV/DEC2011)
CONSTRUCTION:
This frequency meter is a moving iron type instrument which consists of two coils
A&B mounted perpendicular to each other. Each coil is divided into two sections whose
connections are as shown in figure. The branch circuit of coil A has a resistor R A series
with it and a reactance coil LA parallels it. Whereas the branch circuit of coil B has a
reactance coil LB series with it and a reactance RB parallel to it. The moving element is a
soft iron needle, which is also called magnetic needle. This needle is pivoted on a
spindle, which also carries a pointer and damping vanes. A reactance coil L is connected
in series with the supply to suppress higher harmonics in the current of the meter, and
therefore it tends to minimize the waveform errors in its indication. There is no controlling
force.

30
www.rejinpaul.com
PRINCIPLE OF OPERATION:
When the meter is connected across the supply, the two coils carry currents which
setup two magnetic fields at right angles to each other terminal of an AND gate. A
constant gate pulse of I sec is applied to the other input terminal of the AND gate as
shown in the fig. Number of pulses counted at the output terminal for a period of 1 sec
gives the frequency to be measured.
BASIC BLOCK DIAGRAM:

31
Fig shows the block diagram of a digital frequency meter. The supply voltage
whose frequency is to be measured is first amplified with the help of amplifier. The
amplified voltage signal is fed to the Schmitt trigger which converts the input signal into
a square wave with fast rise and fall times, which is then differentiated and clipped in
order to produce a train of pulses.
 Each pulse represents a cycle of the voltage signal with unknown frequency. The
output pulses from the Schmitt trigger are fed to a START/STOP gate which is an AND
gate. This AND gate is enabled and disabled by giving a time interval to one of the input
terminals of the gate.
 When this gate is enabled, the input pulses pass through this gate and are fed
directly to an electronic counter, which counts the number of pulses. When this gate is
disabled, the counter stops counting the incoming pulses.
 The counter displays the number of pulses that have passed through it in the time
interval between START and STOP. Using the time interval and the number of pulses,
the unknown frequency can be calculated.
BASIC ELECTRONIC FREQUENCY COUNTER:

o Both these fields act upon the soft iron needle and deflects it which depends upon
the relative magnitude of the two fields and hence of the current through the coils.
o The values of RA,LA,RB and LB are so choosen that, at normal frequency equal
currents flow through the coil A and B thereby making the needle and pointer to take up
the mean position.
o When equal currents flow through the coils A and B, the needle will be at 45° to
both the coils and the pointer will be at the centre of the scale as shown in the figure.
o If the frquency increasesabove its normal value, reactances LA and LB increase
while the resistances RA and RB remain the same.
o Hence the voltage drop on coil A increases as compared to that of coil B, thereby
increasing the current through coil A as compared to coil B. Thus the magnetic field of
coil A becomes stronger than that of coil B.
o Because of the tedency of the needle to deflect towards the stronger field, it tends
to st itself in line with the axis of coil A, thus making the pointer deflects to the left.
o If the frequency deacreses below its normal value, reactances LA and LB
deacrease while the resistances RA and RB remain the same. Hence the voltage drop
on coil A deacreases as compared to that of coil B, thereby deacreasing the current

32
www.rejinpaul.com
through coil A as compared to coil B.Thus the magnetic field of coil B becomes stronger
than that of A.
o Because of the tedency of the needle to deflect towards the stronger field, it tends
to st itself in line with the axis of coil B, thus making the pointer deflects to the right.
ADVANTAGES:
1. Simple in construction.
2. Simple operation.
3. Gives an accurate measurement.
PART C(15 MARK)
1. Explain about the working principle of electrodynamometer type instrument.
(NOV/DEC 13)
o The necessity for the a.c. calibration of moving iron instruments as well as other
types of instruments which cannot be correctly calibrated requires the use of a transfer
type of instrument.
o A transfer instrument is one that may be calibrated with a d.c. source and then
used without modification to measure a.c. This requires the transfer type instrument to
have same accuracy for both d.c. and a.c., which the electrodynamometer instruments
have.
o These standards are precision resistors and the Weston standard cell (which is a
d.c. cell).It is obvious, therefore, that it would be impossible to calibrate an a.c.
instrument directly against the fundamental standards. The calibration of an a.c.
instrument may be performed as follows.
o The transfer instrument is first calibrated on d.c. This calibration is then
transferred to the a.c. instrument on alternating current, using operating conditions
under which the latter operates properly. Electrodynamic instruments are capable of
service as transfer instruments.
o Indeed, their principal use as ammeters and voltmeters in laboratory and
measurement work is for the transfer calibration of working instruments and as
standards for calibration of other instruments as their accuracy is very high.
o Electrodynamometer types of instruments are used as a.c. voltmeters and
ammeters both in the range of power frequencies and lower part of the audio power
frequency range. They are used as watt-meters, and with some modification as power
factor meters and frequency meters.

33
www.rejinpaul.com
Operating Principle of Electrodynamometer Type Instrument

 It would have a torque in one direction during one half of the cycle and an equal
effect in the opposite direction during the other half of the cycle.If the frequency were
very low, the pointer would swing back and forth around the zero point.
 However, for an ordinary meter, the inertia is so great that on power frequencies
the pointer does not go very far in either direction but merely stays (vibrates slightly)
around zero.
 If, however, we were to reverse the direction of the flux each time the current
through the movable coil reverses, a unidirectional torque would be produced for both
positive and negative halves of the cycle.
 In electrodynamometer instruments the field can be made to reverse
simultaneously with the current in the movable coil if the field (fixed) coil is connected in
series with the movable coil.
Construction of Electrodynamometer type instrument
Fixed Coils
The field is produced by a fixed coil. This coil is divided into two sections to give a more
uniform field near the centre and to allow passage of the instrument shaft.
Moving Coil
A single element instrument has one moving coil. The moving coil is wound either as a
self-sustaining coil or else on a nonmetallic former. A metallic former cannot be used as
eddy current would be induced in it by the alternating field. Light but rigid construction is
used for the moving coil. It should be noted that both fixed and moving coils are air
cored.

34
Control www.rejinpaul.com
The controlling torque is provided by two control springs. These springs act as
leads to the moving coil.
Moving System
The moving coil is mounted on an aluminum spindle. The moving system also
carries the counter weights and truss type pointer. Sometimes a suspension may be
used in case a high sensitivity is desired.
Damping
Air friction damping is employed for these instruments and is provided by a pair of
aluminum vanes, attached to the spindle at the bottom. These vanes move in sector
shaped chambers. Eddy current damping cannot be used in these instruments as the
operating field is very weak (on account of the fact that the coils are air cored) and any
introduction of a permanent magnet required for eddy current damping would distort the
operating magnetic field of the instrument.
Shielding
The field produced by the fixed coils is somewhat weaker than in other types of
instruments It is nearly 0.005 to 0.006 Wb/m In d.c. measurements even the earth
magnetic field may affect the readings. Thus it is necessary to shield an
electrodynamometer type instrument from the effect of stray magnetic fields. Air cored
electrodynamometer type instruments are protected against external magnetic fields by
enclosing them in a casing of high permeability alloy. This shunts external magnetic
fields around the instrument mechanism and minimizes their effects on the indication.
Cases and Scales
Laboratory standard instruments are usually contained in highly polished wooden
cases. These cases are so constructed as to remain dimensionally stable over long
periods of time. The glass is coated with some conducting material to completely remove
the electrostatic effects. The case is supported by adjustable leveling screws. A spirit
level is also provided to ensure proper leveling. The scales are hand drawn, using
machine sub-dividing equipment. Diagonal lines for fine sub-division are usually drawn
for main markings on the scale. Most of the high-precision instruments have a 300 mr
scale with 100, 120 or 150 divisions.
Errors in Electrodynamometer Instruments
i) Frequency error
ii) Eddy current error

35
iii) External magnetic field www.rejinpaul.com

iv) Temperature changes
Advantages
i) These instruments can be used on both a.c & d.c
ii) Accurate rms value
Disadvantages
(i) They have a low torque/weight ratio and hence have a low sensitivity.
(ii) Low torque/weight ratio gives increased frictional losses.
(iii) They are more expensive than either the PMMC or the moving iron type
instruments.
2. Explain in detail the PMMC instrument with neat sketch. (NOV/DEC2014)

The permanent magnet moving coil instrument is the most accurate type for DC
measurements. The working principle of these instruments is the same as that of the D’
Arsonval type of galvanometers, the difference being that a direct reading instrument is
provided with a pointer and a scale.
Construction of PMMC Instruments

 The moving coil is wound with many turns of enameled or silk covered copper
wire. The coil is mounted on a rectangular aluminium former which is pivoted on jeweled
bearings. The coils move freely in the field of a permanent magnet.
 Most voltmeter coils are wound on metal frames to provide the required electro-
magnetic damping.
36
Most ammeter coils, however, are wound on non -magnetic formers, because coil
turns are effectively shorted by the ammeter shunt.
Magnet Systems
 Old style magnet system consisted of relatively long U shaped permanent
magnets having soft iron pole pieces.
 Owing to development of materials like Alcomax and Alnico, which have a high
coercive force, it is possible to use smaller magnet lengths and high field intensities.
 The flux densities used in PMIMC instruments vary from 0.1 W b/m to 1 Wb/m
Control
When the coil is supported between two jewel bearings the control torque is provided by
two phosphor bronze hair springs. These springs also serve to lead current in and out of
the coil. The control torque is provided by the ribbon suspension as shown. This method
is comparatively new and is claimed to be advantageous as it eliminates bearing friction.
Damping
Damping torque is produced by movement of the aluminium former moving in the
magnetic field of the permanent magnet.
Pointer and Scale
 The pointer is carried by the spindle and moves over a graduate d scale. The
pointer is of light-weight construction and, apart from those used in some inexpensive
instruments has the section over the scale twisted to form a fine blade.
 This helps to reduce parallax errors i n the reading of the scale. When the coil is
supported between two jewel bearings the control torque is provided by two phosphor
bronze hair springs.
Torque Equation:
The torque equation of a moving coil instrument is given by
Deflecting torque Td = NBI dl = GI
where G = a constant = NB dl
The spring control provides a restoring torque Tc = Kθ
where K = spring constant
For final steady deflection Tc = Td
Final steady deflection θ= (G/K) I
As the deflection is directly proportional to the current passing through the meter (K and
G being constants) we get a uniform (linear) scale for the instrument.

37
Errors in PMMC Instruments www.rejinpaul.com

The main sources of errors in moving coil instruments are due to
 Weakening of permanent magnets due to ageing at temperature effects.
 Weakening of springs due to ageing and temperature effects.
 Change of resistance of the moving coil with temperature.
Advantages:
1. The scale is uniformly divided.
2. The power consumption is very low
3. The torque-weight ratio is high which gives a high accuracy. Ø A single instrument
may be used for many different current and voltage ranges by using different values for
shunts and multipliers.
4. Self-shielding magnets make the core magnet mechanism particularly useful in
aircraft and aerospace applications.
Dis-advantages:
1. These instruments are useful only for DC. The torque reverses if the current
reverses. If the instrument is connected to AC., the pointer cannot follow the rapid
reversals and the deflection corresponds to mean torque, which is zero. Hence these
instruments cannot be used for AC.
2. The cost of these instruments is higher than that of moving iron instruments.
3.a)What are the major considerations in selecting a Voltmeter.(MAY/JUNE 13)
INPUT IMPEDANCE:
The input impedance should be atleast an order of magnitude higher than the
impedance of the circuit under measurement to avoid loading effects.
VOLTAGE RANGE:
The voltage ranges on the meterscale may be in the 1-3-10 sequence with 10 db
of separation, or in the 1.5-5-1.5 sequence or in a single scale calibrated in decibels.
Decibels ;
Incase of measurements a wide range of voltages use of the decibel scale can
be very effective. All voltmeter with db scale are caliberated in dbm, referred to some
particular impedance.

38
SensitivityVs Bandwidth: www.rejinpaul.com

Noise is a function of bandwidth. A voltmeter with a broad bandwidth will pickup
and generate more noise than one operating over a narrow range of frequencies.
b)write shot notes on digital multimeter. (MAY/JUNE 13)

The digital multimeter is an instrument which is capable of measuring are
voltages,d.c voltages, a.c and d.c currents and resistances over several ranges.
The current is converted to voltage by passing it through low shunt resistance.
The a.c quantities are converted to d.c by employing various rectifiers and filtering
circuits.
For resistance measurements the meter consists of a precision low current square
that is applied across the unknown resistance which gives d.c voltage.
All the quantities are digitized using analog to digital converter and displayed in
the digital form on the display. In addition the output digital multimeters can also be
used to interference with some other equipments.
Advantages:
1. The accuracy is very high
2. The input impedance is very high
3. The size is compact and cost is also low.

39
UNIT III www.rejinpaul.com

COMPARISON METHODS OF MEASUREMENTS
PART-A
1. Write the necessary balance conditions for a Schering bridge. (Nov/Dec 12)
Rx = R3 *R42C4
R42 C2
RX = R3C4
R3
CX = R4 C2
R3
2.Define transformer Ratio Bridge.
The transformer ratio bridges are replacing the conventional AC bridges which consist of
voltage transformer whose performance approaches that of an ideal transformer.
3.Define interference.
The instruments used for electrical measurements are in an environment which contains
many sources of electrical and magnetic energy. These sources can produce
undesirable signals called interference.
4. What is the need for screening? (Apr/May15)
Screening is a process of preventing EM radiation from coupling into or leaking out of
defined areas, or regions.
5. What are the applications of potentiometers? (Nov/Dec13)
a) Calibration of voltmeter
b) Calibration of ammeter
c) Calibration of wattmeter
d) Measurement of resistance
e) Measurement of power
6.How does a Hay’s bridge differ from Maxwell’s bridge? What is its uniqueness?
(May/Jun13)
 The difference in Maxwell’s bridge and Hay’s bridge is that the hay’s bridge
consists of resistance R1 in series with standard capacitor C1 in one of the ratio arms.
 Hence for larger phase angle, R1 needed is very low, which is practicable
 Hence bridge can be used for the coils with high values.

40
7.Which instrument is used for measuring very highwww.rejinpaul.com

resistance found in cable
insulations? (May/Jun13)
Kelvin bridge were used for measuring very high resistance found in cable insulations.
8.List the applications of ac bridge.(April/May 2011)
Measurement of inductance ,capacitance, storage factor, loss factor may be made
conveniently and accurately by employing ac bridge network
9.Enumerate the principle of grounding. .(April/may 2011)
The Shielding and grounding of bridge is one way of reducing the effect of stray
capacitances . But this technique does not eliminate the stray capacitances but makes
them constant in value and hence they can be compensated .
10.Which bridge is used to measure incremental inductance? (Nov/Dec 2011)
Hay’s bridge is used to measure incremental inductance.
11.Define the term standardization of potentiometer.(Nov/Dec 2009)
Before putting the potentiometer in in use it is standardized by the adjustment of current
from the supply battery by direct reading.
12.What are the advantages of Kelvins double Bridge?
 The effect of lead and contact resistance is completely eliminated.
 It is mainly designed for measurement of very low resistance
PART-B
1. Explain Maxwell Bridge in detail with neat circuit diagram.
Definition
A Maxwell Bridge (in long form, a Maxwell-Wien bridge) is a type of Wheatstone bridge
used to measure an unknown inductance (usually of low Q value) in terms of calibrated
resistance and capacitance. It is a real product bridge.
The Maxwell Bridge is used to measure unknown inductance in terms of calibrated
resistance and capacitance. Calibration-grade inductors are more difficult to
manufacture than capacitors of similar precision, and so the use of a simple
"symmetrical" inductance bridge is not always practical.

41
Circuit Diagram www.rejinpaul.com
Explanation
With reference to the picture, in a typical application R1 and R4 are known fixed entities,
and R2 and C2 are known variable entities. R2 and C2 are adjusted until the bridge is
balanced. R3 and L3 can then be calculated based on the values of the other
components.
As shown in Figure, one arm of the Maxwell bridge consists of a capacitor in parallel with
a resistor (C1 and R2) and another arm consists of an inductor L1 in series with a
resistor (L1 and R4). The other two arms just consist of a resistor each (R1 and R3). The
values of R1 and R3 are known, and R2 and C1 are both adjustable. The unknown
values are those of L1 and R4. Like other bridge circuits, the measuring ability of a
Maxwell Bridge depends on 'Balancing' the circuit.
Balancing the circuit means adjusting C1 and R2 until the current through the bridge
between points A and B becomes zero. This happens when the voltages at points A and
B are equal.
Mathematically,
Z1 = R2 + 1/ (2πfC1); while Z2 = R4 + 2πfL1.

(R2 + 1/ (2πfC1)) / R1 = R3 / [R4 + 2πfL1];
or
R1R3 = [R2 + 1/ (2πfC1)] [R4 + 2πfL1]
To avoid the difficulties associated with determining the precise value of a variable
capacitance, sometimes a fixed-value capacitor will be installed and more than one
resistor will be made variable. The additional complexity of using a Maxwell bridge over
simpler bridge types is warranted in circumstances where either the mutual inductance
between the load and the known bridge entities, or stray electromagnetic interference,
distorts the measurement results.
42
www.rejinpaul.com
The capacitive reactance in the bridge will exactly oppose the inductive reactance of the
load when the bridge is balanced, allowing the load's resistance and reactance to be
reliably determined.
Advantages:
 The frequency does not appear
 Wide range of inductance

Disadvantages:
 Limited measurement
 It requires variable standard capacitor
2) Explain Schering Bridge with neat circuit diagram in detail.

Definition
A Schering Bridge is a bridge circuit used for measuring an unknown electrical
capacitance and its dissipation factor. The dissipation factor of a capacitor is the the ratio
of its resistance to its capacitive reactance. The Schering Bridge is basically a four-arm
alternating-current (AC) bridge circuit whose measurement depends on balancing the
loads on its arms. Figure 1 below shows a diagram of the Schering Bridge.
Diagram
Explanation
In the Schering Bridge above, the resistance values of resistors R1 and R2 are known,
while the resistance value of resistor R3 is unknown. The capacitance values of C1 and
43
C2 are also known, while the capacitance of C3 is thewww.rejinpaul.com

value being measured. To
measure R3 and C3, the values of C2 and R2 are fixed, while the values of R1 and C1
are adjusted until the current through the ammeter between points A and B becomes
zero. This happens when the voltages at points A and B are equal, in which case the
bridge is said to be 'balanced'.
When the bridge is balanced, Z1/C2 = R2/Z3, where Z1 is the impedance of R1 in
parallel with C1 and Z3 is the impedance of R3 in series with C3.
In an AC circuit that has a capacitor, the capacitor contributes a capacitive reactance to
the impedance.
Z1 = R1/[2πfC1((1/2πfC1) + R1)] = R1/(1 + 2πfC1R1)
while Z3 =1/2πfC3 + R3. 2πfC2R1/ (1+2πfC1R1) = R2/(1/2πfC3 + R3); or
2πfC2 (1/2πfC3 + R3) = (R2/R1) (1+2πfC1R1); or
C2/C3 + 2πfC2R3 = R2/R1 + 2πfC1R2.
When the bridge is balanced, the negative and positive reactive components are equal
and cancel out, so
2πfC2R3 = 2πfC1R2 or
R3 = C1R2 / C2.
Similarly, when the bridge is balanced, the purely resistive components are equal,
C2/C3 = R2/R1 or C3 = R1C2 / R2.
Advantages:
 Balance equation is independent of frequency
 Used for measuring the insulating properties of electrical cables and equipment’s
3.Discuss the effects of electrostatic and electromagnetic interference in

instruments(Apr/May15)
INTERFERENCE BY RADIATION.
Interference by electromagnetic radiation becomes important at cable lengths
greater than 1/7 of the wavelength of the signals. At frequencies beyond 30Mhz, most of
the interference occurs by electro magnetic radiation
INTERFERENCE BY ELECTROSTATIC CHARGE.
Charged persons and objects can store electrical charges of up to several micro-
Coulombs, which means voltages of some 10kV in respect to ground. Dry air, artificial
fabrics and friction favour these conditions.When touching grounded equipment, an

44
www.rejinpaul.com
instantaneous discharge produces arcing with short, high current pulses and associated
strong changes of the e.m. field.
REDUCTION OF INTERFERENCE
There are a number of methods to prevent interference. But all of them only
reduce the interference and never fully prevent it. This means there will never be a
system which is 100% safe from interference. Because the efforts and the cost will rise
with the degree of reduction of interference, a compromise has to be found between the
effort and the result.
The requirement for the reduction of interference will depend on:
- The strength of the interference source
- The sensitivity of the interference sink
- The problems caused by interference
4.How a DC potentiometer is used for the calibration of a voltmeter? Explain it with

a diagram.(Apr/May 15)
An instrument that precisely measures an electromotive force (emf) or a voltage
by opposing to it a known potential drop established by passing a definite current through
a resistor of known characteristics.
o There are two ways of accomplishing this balance: (1) the current I may be held at
a fixed value and the resistance R across which the IR drop is opposed to the unknown
may be varied; (2) current may be varied across a fixed resistance to achieve the
needed IR drop.
 The essential features of a general-purpose constant-current instrument are
shown in the illustration. The value of the current is first fixed to match an IR drop to the
emf of a reference standard cell. With the standard-cell dial set to read the emf of the
reference cell, and the galvanometer (balance detector) in position G1, the resistance of
the supply branch of the circuit is adjusted until the IR drop in 10 steps of the coarse dial
45
plus the set portion of the standard-cell dial balanceswww.rejinpaul.com

the known reference emf,
indicated by a null reading of the galvanometer.
 This adjustment permits the potentiometer to be read directly in volts. Then, with
the galvanometer in position G2, the coarse, intermediate, and slide-wire dials are
adjusted until the galvanometer again reads null. If the potentiometer current has not
changed, the emf of the unknown can be read directly from the dial settings.
 There is usually a switching arrangement so that the galvanometer can be quickly
shifted between positions 1 and 2 to check that the current has not drifted from its set
value.
 Circuit diagram of a general-purpose constant-current potentiometer, showing
essential features Potentiometer techniques may also be used for current
measurement, the unknown current being sent through a known resistance and the IR
drop opposed by balancing it at the voltage terminals of the potentiometer.
 Here, of course, internal heating and consequent resistance change of the
current-carrying resistor (shunt) may be a critical factor in measurement accuracy; and
the shunt design may require attention to dissipation of heat resulting from its I2R power
consumption.
 Potentiometer techniques havebeen extended to alternating-voltage
measurements, but generally at a reduced accuracy level (usually 0.1% or so). Current
is set on an ammeter which must have the same response on ac as on dc, where it may
be calibrated with a potentiometer and shunt combination.
 Balance in opposing an unknown voltage is achieved in one of two ways: (1) a
slide-wire and phase-adjustable supply; (2) separate in-phase and quadrature
adjustments on slide wires supplied from sources that have a 90° phase difference.
Such potentiometers have limited use in magnetic testing.

46
5.Explain about the AC potentiometer.(APR/MAY 15) www.rejinpaul.com

This potentiometer is an exceedingly useful one for the accurate measurement of
alternating currents and voltages, since such measurements are not easily carried out by
some other methods.
The basic principle of AC potentiometer is the same as that of DC potentiometer.
The main difference between these two is “whereas in the DC potentiometer only the
magnitudes of the “unknown” emf and slide wire voltage drop must be made equal to
obtain balance. In the AC potentiometer the phases of the two voltages, as well as then
magnitudes, must be equal for balance to be obtained.”
The following factors must be considered for the principle of operation of an AC
potentiometer.
1. In all the types of AC potentiometers, the potentiometer circuit must be supplied
from the same source as the voltage or current being measured.
2. There AC supply should be free from harmonics because in the presence of
harmonic it may not ne possible to achieve balance. The input supply should be
sinusoidal.
3. There being no reference source (the reference source is DC being of standard
cell or a zener source) the absolute accuracy with which an AC voltage can be measured
in an AC potentiometer cannot be comparable with corresponding type of DC
measurement.
4. Extraneous or stray emfs picked up from fields or coupling between portions of the
potentiometer circuit arrangement, which seriously affect the result, must be eliminated.
Compensated for and or measured (since they may add vecorically to the emf being
measured).
Standardisation of AC potentiometers:
The AC type potentiometers are made direct reading type,i.e., the readings are
read off directly from the dial settings. In order to do this, the AC potentiometer must be
standardized as is done in case of DC type instruments.
The standardization is achieved by with the help of standard DC source, i.e, a
standard cell or a zener source and a transfer instrument. This transfer instrument is an
electrodynamometer milliammeter, so constructed that its response to alternating
currents is the same as its DC response. Such an instrument can be calibrated on DC
and then brought to the same setting on AC. Otherwise, we can use thermocouple type
of instrument as a transfer instrument.

47
Types of AC potentiometer www.rejinpaul.com

It can be classified according to the manner in which the instrument dials (or
scales)present the value of unknown voltage. There are two types.
1. Polar potentiometers.
2. Co-ordinate potentiometers
1. Polar potentiometers
In this type of potentiometers, the unknown emf is measured in polar form i.e., in
terms of its magnitude and relative phase. Here, the magnitude is given by one scale and
its phase angle with respect to some reference vector is given by the second (other)
scale. Provision is made for reading phase angles upto 360°. Figure shows that the
voltage is read in the form V The example for this type of instrument is Drysdale polar
potentiometer.
2. Co-ordinate potentiometers
Here, the unknown emf is measured in terms of its components along and perpendicular
to a standard axis. There are two unknown components of an emfs.
COMPARISON METHODS OF MEASUREMENTS
These two are given directly by two different scales known as “in phase”
(V1) and “quadrature” (V2) scales.
Provision is made in this type of instruments to read positive and negative values
of voltages so that all angles upto 360° are covered.
Voltage V = √V12 + V22
θ = tan-1 (V2/V1)
Examples of this instrument are Gall-Tinsley and Campbell-Larsen type instruments.
3. Dryscale polar potentiometer
Figure shows a drysdale polar AC potentiometer.
For AC measurements, the slide wire AB is supplied from a phase shifting circuit so
arranged that the magnitude of the voltage supplied by it remains constant while its
48
www.rejinpaul.com
phase can be varied through 360°. Consequently, slide-wire current I1 is maintained
constant in magnitude but varied in phase.
The phase shifting circuit consists of two stator windings. These two stator
windings are supplied from the same source in parallel. Their currents are made to differ
by 90° by using phase shifting technique.
The two stator windings produce rotating flux which induces a secondary emf in
the rotor winding which is of constant magnitude but the phase of which can be varied by
rotating the rotor circuit emf is read from the circular graduated dial provided for the
purpose. The ammeter A in the slide wire circuit is of electrodynamic or thermal type
before using it for AC measurements, the potentiometer is first calibrated by using DC
supply for slide wire and standard cell for test terminals T 1 and T2.
The unknown input AC voltage to be measured is applied across test terminals T1
and T2. The balance is effected by the alternate adjustment of the slide wire contact and
position of phase shifting rotor. This slide-wire reading represents the magnitude of the
test voltage and voltage phase shifter reading gives the phase with reference to an
arbitrary reference vector.20
PART C(15 Mark)

1. Give detailed notes on earthing.
This is one of the simplest but most efficient methods to reduce interference.
Grounding can be used for three different purposes:
1. Protection Ground
Provides protection for the operators from dangerous voltages. Widely used on mains-
operated equipment.
2. Function Ground
The ground is used as a conductive path for signals. Example: in asymmetrical cables
screen, which is one conductor for the signal, is connected to the ground.
3. Screening Ground
 Used to provide a neutral electrical path for the interference, to prevent that the
interfering voltages or currents from entering the circuit. In this chapter we will only
consider the third aspect.
 Grounding of equipment is often required for the cases 1 or 2 anyhow, so that the
screening ground is available "free of charge". Sometimes the grounding potential,
provided by the mains connection, is very "polluted".
49
 This means that the ground potential itself alreadywww.rejinpaul.com

carries an interfering signal.
This is especially likely if there are big power consumers in the neighborhood or even
in the same building.
 Using such a ground might do more harm than good. The quality of the ground
line can be tested by measuring it with a storage scope against some other ground
connection, e.g. a metal water pipe or some metal parts of the construction.
Never use the Neutral (N) of the mains as ground.
 It might contain strong interference; because it carries the load current of all
electrical consumers. The grounding can be done by single-point grounding or by multi-
point grounding. Each method has advantages which depend on the frequency range of
the signal frequencies.
 All parts to be grounded are connected to one central point. This results in no
"ground loops" being produced. This means the grounding conductors do not form any
closed conductive path in which magnetic interference could induce currents.
Furthermore, conductive lines between the equipment are avoided, which could produce
galvanic coupling of interference.
 Central grounding requires consistent arrangement of the grounding circuit and
requires insulation of the individual parts of the circuit. This is sometimes very difficult to
achieve in a system using the single-point grounding.
Multi-point grounding:
In multi-point grounding all parts are connected to ground at as many points as
possible. This requires that the ground potential itself is as widely spread as possible. In
practice, all conductive parts of the chassis, the cases, the shielding, the room and the
installation are included in the network.
Screening:
When considering the effect of electrical and magnetic fields, we have to
distinguish between low and high frequencies. At high frequencies the skin effect plays
an important role for the screening. The penetration describes the depth from the surface
of the conductor, where the current density has decayed to 37% compared to the surface
of the conductor.
Screening of cables:
 When signal lines run close to interference sources or when the signal circuit is
very sensitive to interference, screening of signal lines will give an improvement. There

50
are different ways of connecting the cable screen: Threewww.rejinpaul.com

different ways of connecting
the cable screen. Cable screen not connected.
 This screen will not prevent any interference, because the charge on the screen,
produced by interference, will remain and will affect the central signal line. Also, the
current induced by interference in the line will flow through the sink, affecting the signal.
Cable screen grounded on one side only.
 This screen will only prevent interference at low frequency signals. For
electromagnetic interference, where the wavelength is short compared to the length of
the cable, the screening efficiency is poor.
 Cable screen grounded on either side is effective for all kinds of interference. Any
current induced in the screen by magnetic interference will flow to ground. The inner of
the cable is not affected. Only the voltage drop on the screen will affect the signal in the
screen.
2. Explain Hay’s Bridge with neat circuit diagram in detail.
A Hay Bridge is an AC bridge circuit used for measuring an unknown inductance
by balancing the loads of its four arms, one of which contains the unknown inductance.
One of the arms of a Hay Bridge has a capacitor of known characteristics, which is the
principal component used for determining the unknown inductance value. Figure 1 below
shows a diagram of the Hay Bridge.
Explanation
As shown in Figure 1, one arm of the Hay bridge consists of a capacitor in series with a
resistor (C1 and R2) and another arm consists of an inductor L1 in series with a resistor
(L1 and R4).
The other two arms simply contain a resistor each (R1 and R3). The values of R1and R3
are known, and R2 and C1 are both adjustable.
The unknown values are those of L1 and R4.
Like other bridge circuits, the measuring ability of a Hay Bridge depends on 'balancing'
the circuit. Balancing the circuit in Figure 1 means adjusting R2 and C1 until the current
through the ammeter between points A and B becomes zero. This happens when the
voltages at points A and B are equal.

51
Diagram www.rejinpaul.com
When the Hay Bridge is balanced, it follows that Z1/R1 = R3/Z2 wherein Z1 is the
impedance of the arm containing C1 and R2 while Z2 is the impedance of the arm
containing L1 and R4.
Thus, Z1 = R2 + 1/(2πfC) while Z2 = R4 + 2πfL1.
[R2 + 1/(2πfC1)] / R1 = R3 / [R4 + 2πfL1]; or
[R4 + 2πfL1] = R3R1 / [R2 + 1/(2πfC1)]; or
R3R1 = R2R4 + 2πfL1R2 + R4/2πfC1 + L1/C1.
When the bridge is balanced, the reactive components are equal, so
2πfL1R2 = R4/2πfC1, or R4 = (2πf) 2L1R2C1.
Substituting R4, one comes up with the following equation:
R3R1 = (R2+1/2πfC1) ((2πf) 2L1R2C1) + 2πfL1R2 + L1/C1; or
L1 = R3R1C1 / (2πf) 2R22C12 + 4πfC1R2 + 1);
L1 = R3R1C1 / [1 + (2πfR2C1)2]
After dropping the reactive components of the equation since the bridge is
Thus, the equations for L1 and R4 for the Hay Bridge in Figure 1 when it is balanced are:
L1 = R3R1C1 / [1 + (2πfR2C1)2]; and
R4 = (2πfC1)2R2R3R1 / [1 + (2πfR2C1)2]
Advantages:
Simple expression
Disadvantages:
It is not suited for measurement of coil

52
www.rejinpaul.com
3.Explain wheatstone Bridge with neat circuit diagram in detail.
A null-type bridge with d.c. excitation, commonly known as a Wheatstone bridge, has the
form shown in Figure 7.1. The four arms of the bridge consist of the unknown resistance
Ru, two equal value resistors R2 and R3 and a variable resistor Rv (usually a decade
resistance box). A d.c. voltage Vi is applied across the points AC and the resistance Rv
is varied until the voltage measured across points BD is zero. This null point is usually
measured with a high sensitivity galvanometer.
To analyses the Whetstone bridge, define the current flowing in each arm to be I1
. .. I4 as shown in Figure 7.1. Normally, if a high impedance voltage-measuring
instrument is used, the current Im drawn by the measuring instrument will be very small
and can be approximated to zero. If this assumption is made, then, for Im D 0:
I1 =I3 and I2 =I4

53
www.rejinpaul.com

54
UNIT –IV www.rejinpaul.com

STORAGE AND DISPLAY DEVICES
PART-A
1.What are data loggers? (NOV/DEC 13)
The data loggers are used to automatically make a record of the readings of instruments
located at different parts of the plant.
2.Define the deflection sensitivity of CRT.
The deflection sensitivity of a CRT is defined as the deflection of the screen per unit
deflection voltage.
3.What are the different materials used in LED? Also name the colors emitted.
Gallium Arsenide phosphate, Gallium Arsenide and Gallium phosphide. It emits red,
yellow and green colors.
4.Distinguish between LED & LCD.(Nov/Dec 13)
Parameter LED Dynamic Field effect LCD
scattering LCD
Power/digit 10-140 mw 100µw 1 to 10 µw
depending on
color
Voltage 5V 18V 3 to 7V
Switching speed 1 µs 300 ms 100 to 300ms
Colors Red, orange, Depends on Depends on
Yellow and Green illumination illumination
5.What are the various components of a recording instrument? (May/Jun13)
 Recording head
 Magnetic tape
 Reproducing head
 Tape transport mechanism
 Conditioning devices.
6.Reason out why today’s commercial LED monitor have become more popular
than their LCD counterparts.(May/Jun 13)
 Less power consumption
 Low cost
 Uniform brightness with good contrast

55
7.List any two storage devices.(April/may 2011) www.rejinpaul.com

1) Bitable storage oscilloscopes 2) fast storage oscilloscopes 3) Digital storage
oscilloscopes
8.Differentiate the functions of printer and plotter. (April/ May 2011)
Printers are the most commonly used output devices today for producing hard copy
output. Analog X-Y recorders are replaced by digital x-y recorders it is known as digital
plotters .to mesure the performance of the digital plotters are used .
9.How does dynamic scattering type LCD work? (Nov/Dec 2011)
When not activated the transmittive type cell simply transmits the light through the cell in
the straight lines. In this condition the cell will not appear bright .When the cell is
activated, the incident light is scattered forward and the cell appears quite bright even
under high intensity light conditions
10) What are the advantage of magnetic tape recorder? (Nov/Dec 2011)
i) Magnetic tape can be recorded over and reused repeatedly.
ii) Large amounts of information is stored.
iii) Magnetic tape is inexpensive and budget friendly.
11) What are the merits of digital storage oscilloscope?(May 2010)
 Infinite storage time
 Easy to operate
 Signal processing is possible
 Cursor measurement is possible
 A number of traces depending on memory size can be stored & Recalled
12) What are the types of printers? (Dec 2009)
 Drum & Chain printer
 Dot matrix printer
 Inkjet Printer
 Laser Printer
PART-B
1) With neat diagram, explain the parts of CRT in detail.(NOV/DEC 14)
The device which allows, the amplitude of such signals, to be displayed primarily as a
function of time, is called cathode ray oscilloscope. The cathode ray tube (CRT) is the
heart of the C.R.O. The CRT generates the electron beam, accelerates the beam,

56
www.rejinpaul.com
deflects the beam and also has a screen where beam becomes visible as a spot. The
main parts of the CRT are
i) Electron gun
ii) Deflection system
iii) Fluorescent screen
iv) Glass tube or envelope
v) Base
Electron gun
The electron gun section of the cathode ray tube provides a sharply focused,
electron beam directed towards the fluorescent-coated screen. This section starts from
thermally heated cathode, emitting the electrons. The control grid is given negative
potential with respect to cathode. This grid controls the number of electrons in t beam,
going to the screen. The momentum of the electrons (their number x their speed)
determines the intensity, or brightness, of the light emitted from the fluorescent screen
due to the electron bombardment. The light emitted is usually of the green colour.
Deflection System
When the electron beam is accelerated it passes through the deflection system,
with which beam can be positioned anywhere on the screen.
Fluorescent Screen
 The light produced by the screen does not disappear immediately when
bombardment by electrons ceases, i.e., when the signal becomes zero.
 The time period for which the trace remains on the screen after the signal becomes
zero is known as “persistence or fluorescence”. The persistence may be as short as a
few micro second, or as long as tens of seconds or even minutes.
 Medium persistence traces are mostly used for general purpose applications. Long
persistence traces are used in the study of transients. Long persistence helps in the

57
www.rejinpaul.com
study of transients since the trace is still seen on the screen after the transient has
disappeared.
Glass Tube
All the components of a CRT are enclosed in an evacuated glass tube called envelope.
This allows the emitted electrons to move about freely from one end of the tube to the
other end.
Base
The base is provided to the CRT through which the connections are made to the various
parts.
2) Write detailed notes on applications of LCD with necessary sketches.(NOV/DEC
14)
A liquid crystal display (LCD) is a thin, flat electronic visual display that uses the light
modulating properties of liquid crystals (LCs). LCs do not emit light directly. They are
used in a wide range of applications including: computer monitors, television, instrument
panels, aircraft cockpit displays, signage, etc. They are common in consumer devices
such as video players, gaming devices, clocks, watches, calculators, and telephones.
LCDs have displaced cathode ray tube (CRT) displays in most applications. They are
usually more compact, lightweight, portable, less expensive, more reliable, and easier on
the eyes. They are available in a wider range of screen sizes than CRT and plasma
displays, and since they do not use phosphors, they cannot suffer image burn-in. LCDs
are more energy efficient and offer safer disposal than CRTs.
Each pixel of an LCD typically consists of a layer of molecules aligned between

two transparent electrodes, and two polarizing filters, the axes of transmission of which
are (in most of the cases) perpendicular to each other. With no actual liquid crystal
between the polarizing filters, light passing through the first filter would be blocked by the
second (crossed) polarizer. In most of the cases the liquid crystal has double refraction.

58
www.rejinpaul.com
The surfaces of the electrodes that are in contact with the liquid crystal material
are treated so as to align the liquid crystal molecules in a particular direction. This
treatment typically consists of a thin polymer layer that is uni-directionally rubbed using,
for example, a cloth. The direction of the liquid crystal alignment is then defined by the
direction of rubbing. Electrodes are made of a transparent conductor called Indium Tin
Oxide (ITO).
 Before applying an electric field, the orientation of the liquid crystal molecules is
determined by the alignment at the surfaces of electrodes. In a twisted nematic device
(still the most common liquid crystal device), the surface alignment directions at the two
electrodes are perpendicular to each other, and so the molecules arrange themselves in
a helical structure, or twist.
 This reduces the rotation of the polarization of the incident light, and the device
appears grey. If the applied voltage is large enough, the liquid crystal molecules in the
center of the layer are almost completely untwisted and the polarization of the incident
light is not rotated as it passes through the liquid crystal layer.
This light will then be mainly polarized perpendicular to the second filter, and thus
be blocked and the pixel will appear black. By controlling the voltage applied across the
liquid crystal layer in each pixel, light can be allowed to pass through in varying amounts
thus constituting different levels of gray. This electric field also controls (reduces) the
double refraction properties of the liquid crystal.
o LCD with top polarizer removed from device and placed on top, such that the top
and bottom polarizers are parallel. The optical effect of a twisted nematic device in the
voltage-on state is far less dependent on variations in the device thickness than that in
the voltage-off state.
o Because of this, these devices are usually operated between crossed polarizers
such that they appear bright with no voltage (the eye is much more sensitive to
variations in the dark state than the bright state).
o These devices can also be operated between parallel polarizers, in which case
the bright and dark states are reversed. The voltage-off dark state in this configuration
appears blotchy, however, because of small variations of thickness across the device.
 Both the liquid crystal material and the alignment layer material contain ionic
compounds. If an electric field of one particular polarity is applied for a long period of

59
time, this ionic material is attracted to the surfaceswww.rejinpaul.com

and degrades the device
performance.
 This is avoided either by applying an alternating current or by reversing the
polarity of the electric field as the device is addressed (the response of the liquid crystal
layer is identical, regardless of the polarity of the applied field).
 When a large number of pixels are needed in a display, it is not technically
possible to drive each directly since then each pixel would require independent
electrodes. Instead, the display is multiplexed.
 In a multiplexed display, electrodes on one side of the display are grouped and
wired together (typically in columns), and each group gets its own voltage source. On
the other side, the electrodes are also grouped (typically in rows), with each group
getting a voltage sink.
 The groups are designed so each pixel has a unique, unshared combination of
source and sink. The electronics or the software driving the electronics then turns on
sinks in sequence, and drives sources for the pixels of each sink.
3) Discuss in detail about the various types of recorders.(MAY 2012)
The recording procedure performed in magnetic tape recorder can be done by 3

methods. They are
1. Direct recording
2. FM (frequency Modulation) Recording
3. PDM (Pulse Duration Modulation ) recording
Direct recording
The signal to be recorded modulates the current in the recording head. Because
of current modulation, magnetic flux in the recording gap is linearly modulated. When the
tape is moved under the recording head, the magnetic particles retain a state of
permanent magnetization proportional to the flux in the gap.
The input signal is thus converted to a spatial variation of the magnetization of the
particles on the tape. The reproduce head detects these changes as changes in the
reluctance of its magnetic circuit which will induce a voltage in its winding. This voltage is
proportional to the rate of change of flux. The signal on the exposed tape can be
retrieved and played out at any time.

60
Disadvantages: www.rejinpaul.com
(i) . This method cannot be used in DC because reproduce head geneth& a signal which
is proportional to the rate of change of flux.
(ii) Lower limit is around 100 Hz and upper limit is around 2 Mhz.
FM Recording:
o In this FM system, the input signal is used to frequency modulate a carrier which
is then recorded on the tape in the usual way. The central frequency is selected with
respect to the tape speed and frequency deviation selected for the tape recorders is
±40% about the carrier frequency.
o The reproduce head reads the tape in the usual way and sends a signal to the FM
demodulator and low pass filter and the original signal is reconstructed.
 The signal to noise ratio (S/N) of an FM recorder is of the order of 40-50 db, with
an accuracy of less than ±1%. This ±1 db flat frequency response of FM recorder can
go as high as 80 kHz at 120 in/s tape speed, when using very high carrier frequencies
above 400 kHz.
 When high frequency (HF) is not needed and with a View to conserving tape, a
tape speed range selector is generally provided. When the tape speed is changed, the
carrier frequency also changes in the same proportion.
Input to the tape recorders is generally at 1 V level and so most transducers
require amplification before recording. A FM recording system is illustrated in figure. In
this system, a carrier oscillator frequency f6, called the centre frequency, is modulated by
the level of the input signal.
When there is no input signal, the modulation is at centre frequency fc. If a
positive input signal is applied, the frequency deviates from the centre frequency by
some amount in a certain direction, the application of 8 negative input voltage deviates
the carrier frequency in the opposite direction.
61
The output of the modulation, which is fed to the www.rejinpaul.com

tape, is a signal of Constant
frequency for DC inputs and varying frequency for AC inputs. The Variation of frequency
is directly proportional to the amplitude of the input signal. On playback, the output of the
reproduce head is demodulated and fed through a low pass filter which removes the
carrier and other unwanted (frequencies produced due to the modulation process.
o The operation of FM modulation can be easily checked by applying a known input
voltage and measuring the output frequency with an electronic counter. This signal is
applied to the tape with no further conditioning. as the signal is independent of the
amplitude.
 The FM demodulator converts the difference between the centre frequency and
the frequency on the tape, to a voltage proportional to the difference in the frequencies.
This system can thus record frequencies from DC to several thousand Hertz. Residual
carrier signals and out of band noise are removed by a low pass filter.
Advantages:
(i) DC component of the input signal is preserved.
(ii) Wide frequency range.
(iii) No drop out effect due to in homogeneities of the tape material.
(iv) Accurately reproduces the wave form of the input signal.
Disadvantages:
(i) Extremely sensitive to tape speed fluctuations.
(ii) Limited frequency response.
(iii) Requires a high tape speed.
(iv) Requires a high quality of tape transport and speed control.
Pulse Duration Modulation:
Pulse duration modulation allows simultaneous recording of a large number of
slowly changing variables by using Time Division Multiplexing (TDM). The PDM
recording process requires the input signal at the instant of samplingbe converted to a
pulse, the duration of which is proportional to amplitude of the signal at that instant.
As an example, for recording sine wave, it is sampled and recorded at uniformly
spaced discrete intervals instead of continuously recording instantaneous values. The
original sine wave can be reconstructed on playback by passing the discrete readings
through an appropriate filter.

62
www.rejinpaul.com
4.With the help of a functional block diagram explain the working principle of
digital storage oscilloscope mean its advantages over analog CRO.(Nov/Dec 13)
Ø The input signal is applied to the amplifier and attenuator section.

Ø The oscilloscope uses same type of amplifier and attenuator circuitry as used in the
conventional oscilloscopes.
Ø The attenuated signal is then applied to the vertical amplifier.
Ø To digitize the analog signal, analog to digital (A/D) converter is used.
Ø The output of the vertical amplifier is applied to the A/D converter section.
Ø The successive approximation type of A/D converter is most often used in the digital
storage oscilloscopes.
Ø The sampling rate and memory size are selected depending upon the duration& the
waveform to be recorded.
Ø Once the input signal is sampled, the A/D converter digitizes it.
Ø The signal is then captured in the memory.
Ø Once it is stored in the memory, many manipulations are possible as memory can be
readout without being erased.
The block diagram of digital storage oscilloscope is shown in the Fig.
Ø The digital storage oscilloscope has three modes:

1. Roll mode
2. Store mode

63
3. Hold or save mode. www.rejinpaul.com

Advantages
i) It is easier to operate and has more capability. ii) The storage time is infinite.
iii) The display flexibility is available. The number of traces that can be stored and
recalled depends on the size of the memory.
iv) The cursor measurement is possible.
v) The characters can be displayed on screen along with the waveform which can
indicate waveform information such as minimum, maximum, frequency, amplitude etc.
vi) The X-Y plots, B-H curve, P-V diagrams can be displayed.
vii) The pretrigger viewing feature allows to display the waveform before trigger pulse.
viii) Keeping the records is possible by transmitting the data to computer system where
the further processing is possible
ix) Signal processing is possible which includes translating the raw data into finished
information e.g. computing parameters of a captured signal like r.m.s. value, energy
stored etc.
5. (i) Draw the block diagram X-Y Recorder and explain ( 8) (Nov/Dec 2011)
XY recorder
Each of the input signals is attenuated in the range of 0-5mV, so that it can work
in the dynamic range of the recorder
 In X-Y recorder one variable is plotted against another variable. In this recorder,
pen is moved in either X or Y direction on a fixed graph paper.

64
 The writing assembly movement is controlled by www.rejinpaul.com

using either sevo feedback
system or self balancing potentiometer.
 The writing assembly consists of one or two pens depending on this application.
 In practice, X-Y recorder plots one voltage as a function of other voltage.
 Many times X-Y recorder is used to record non electrical physical such as
displacement, pressure, strain etc as a function of another non electrical physical
quantity.
Construction:
 It consists of attenuator which attenuates the input circuit. The balancing signal
and error detector gives error signal.
 This error signal is DC signal. The chopper circuit converts error signal to AC
signal
 The servo amplifier drives servomotor which drives writing assembly on a fixed
graph paper.
 There are two such circuits for two different inputs X and Y. The error signal of X
input is amplified by servo amplifier of X channel driving corresponding servomotor and
pen in X-direction.
 Similar section is performed for Y channel
ii) Explain data loggers in detail.(8) (Nov/Dec 2011)
Definition
Data logger is an electronic device that records data over time or in relation to location
either with a built in instrument or sensor.
Components: 1. Pulse inputs Counts circuit closing 2.Control ports Digital in and out
 Most commonly used to turn things on and off can be programmed as a digital
input excitation outputs. Though they can be deployed while connected to a host PC
over an Ethernet or serial port a data logger is more typically deployed as standalone
devices.
 The term data logger (also sometimes referred to as a data recorder) is commonly
used to describe a self-contained, standalone data acquisition system or device. These
products are comprised of a number of analog and digital inputs that are monitored, and
the results or conditions of these inputs is then stored on some type of local memory
(e.g. SD Card, Hard Drive).
65
 A data logger is a self-contained unit that does not www.rejinpaul.com

require a host to operate. It
can be installed in almost any location, and left to operate unattended. This data can be
immediately analyzed for trends, or stored for historical archive purposes. Data loggers
can also monitor for alarm conditions,
 while recording a minimum number of samples, for economy. If the recording is of
a steady-state nature, without rapid changes, the user may go through rolls of paper,
without seeing a single change in the input.
 A data logger can record at very long intervals, saving paper, and can note when
an alarm condition is occurring. When this happens, the event will be recorded and any
outputs will be activated, even if the event occurs in between sample times. A record of
all significant conditions and events is generated using a minimum of recording
hardcopy.
 The differences between various data loggers are based on the way that data is
recorded and stored.
 The basic difference between the two data logger types is that one type allows the
data to be stored in a memory, to be retrieved at a later time, while the other type
automatically records the data on paper, for immediate viewing and analysis. Many
data loggers combine these two functions, usually unequally, with the emphasis on
either the ability to transfer the data or to provide a printout of it.
PART C(15 MARKS)
1. Explain about digital plotters and Printers.
PRINTERS
Ø Printers can be classified according to their printing methodology Impact printers and
Non- impact printers.
66
Ø Impact printers press formed character faces against an www.rejinpaul.com

inked ribbon onto the paper.
Ø A line printer and dot matrix printer are the examples of an
impact printer.
Ø Non impact printer and plotters use laser techniques, inkjet sprays, xerographic
processes, electrostatic methods and e1ectrothermal methods to get images onto the
paper.
Ø A ink-jet printer and laser printer are the examples of non- impact printers.
Line Printers
A line printer prints a complete line at a time. The printing speed of line printer varies
from 150 lines to 2500 lines per minute with 96 to 100 characters on one line. The line
printers are divided into two categories Drum printers and chain printer.
Drum Printers
Drum printer consists of a cylindr ical drum. One complete set of characters i s
embossed on all the print positions on a l ine, as shown in the Fig. The character to be
printed is adjusted by rotating drum.
In these printers chain with embossed character set is used, instead of drum. Here, the
character to be printed is adjusted by rotating chain.
Dot Matrix Printers
Dot matrix printers are also called serial printers as they print one character at a time,
with printing head moving across a line.

67
www.rejinpaul.com
Laser Printer
Ø The line, do t matrix, and ink jet printers need a head movement on a ribbon to print
characters.
Ø This mechanical movement is relatively slow due to the high inertia of mechanical
elements.
Ø In laser printers these mechanical movements are avoided.
Ø In these printers, an electronically controlled lase r beam traces out the desired
character to be printed on a photoconductive drum.
Ø The exposed areas of the drum gets charged, which attracts an oppositely charged ink
from the ink toner on to the exposed areas.
Ø This image is then transferred to the paper which comes in contact with the drum with
pressure and heat.
Ø The charge on the drum decides the darkness of the print.
Ø When charge is more, more ink is attracted and we get a dark print.

68
www.rejinpaul.com
Ø A colour laser printer works like a single colour laser printer, except that the process is
repeated four times with four different ink colours: Cyan, magenta, yellow and black.
Ø Laser printers have high resolution from 600 dots per inch upto 1200 per inch.
Ø These printers print 4 to 16 page of text per minute.
Ø The high quality and speed of laser printers make them ideal for office environment.
Advantages of Laser printer
Ø The main advantages of laser printers are speed, precision and economy.
Ø A laser can move very quickly, so it can “ write” with much greater speed than an inket.
Ø Because the laser beam has an unvarying diameter, it can draw more precisely,
without spilling any excess ink.
Ø Laser printers tend to be more expensive than ink-jet printers, but it doesn’t cost as
much to keep them running.
Ø Its toner power is cheap and lasts for longer time.
2. Explain the principle of working of a magnetic tape recorder. What are its
basic components and their functions?(Apr/May 15)
The magnetic tape recorders are used for high frequency signal recording. In these
recorders, the data is recorded in a way that it can be reproduced in electrical form any
time. Also main advantage of these recorders is that the recorded data can be replayed
for almost infinite times. Because of good higher frequency response, these are used in
Instrumentation systems extensively.
Basic Components of Tape Recorder:
1. Recording Head
2. Magnetic Tape

69
3. Reproducing Head www.rejinpaul.com

4. Tape Transport Mechanism
5. Conditioning Devices
Recording Head
The construction of the magnetic recording head is very much similar to the
construction of a Transformer having a torroidal core with coil. There is a uniform fine air
gap of 5μm to 15μm between the head and the magnetic tape.
When the current used for recording is passed through coil wound around
magnetic core, it produces magnetic flux. The magnetic tape is having iron oxide
particles. When the tape is passing the head, the flux produced due to recording current
gets linked with iron oxide part ices on the magnetic tape and these particles get
magnetized. This magnetization particle remains as it is, e vent Hough the magnetic tape
leaves the gap. The actual recording takes place at the trailing edge of the air gap.
Any signal is recorded in the form of the patterns. These magnetic patterns are
dispersed anywhere along the length of magnetic tape in accordance with the variation in
recording current with respect to time.
Magnetic Tape
Ø The magnetic tape is made of thin sheet of tough and dimensionally stable plastic
ribbon.
Ø One side of this plastic ribbon is coated by powdered iron oxide particles (Fe2O3)
thick.
Ø The magnetic tape is wound around a reel.
Ø This tape is transferred from one reel to another.

70
Ø When the tape passes across air gap magnetic pattern www.rejinpaul.com
is created in accordance with
variation of recording current.
Ø To reproduce this pattern, the same tape with some recorded pattern is passed across
another magnetic head in which voltage is induced.
Ø This voltage induced is in accordance with the magnetic pattern.
Reproducing Head
Ø The use of the reproducing head is to get the recorded data played back.
Ø The working of the reproducing head is exactly opposite to that of the recording head.
Ø The reproducing head detects the magnetic pattern recorded on the tape.
Ø The head converts the magnetic pattern back to the original electrical signal.
Ø In appearance, both recording and reproducing heads are very much similar.
Tape Transport Mechanism
The tape transport mechanism moves the magnetic tape along the recording head
or reproducing head with a constant speed. The tape transport mechanism must perform
following tasks.
 It must handle the tape without straining and wearing it.
 It must guide the tape across magnetic heads with great precision.
 It must maintain proper tension of magnetic tape.
 It must maintain uniform and sufficient gap between the tape and heads.
 The magnetic tape is wound on reel.
 There are two reels; one is called as supply & other is called as take-up reel.
 Both the reels rotate in same direction.
 The transportation of the tape is done by using supply reel and take-up reel.
 The fast winding of the tape or the reversing of the tape is done by using special
arrangements.
 The rollers are used to drive and guide the tape.

71
Conditioning Devices www.rejinpaul.com

These devices consist of amplifiers and fitters to modify signal to be recorded.
The conditioning devices allow the signals to be recorded on the magnetic tape with
proper format.
Amplifiers allow amplification of signal to be recorded and filters removes
unwanted ripple quantities.
Principle of Tape Recorders
When a magnetic tape is passed through a recording head, the signal to be
recorded appears as some magnetic pattern on the tape. This magnetic pattern is in
accordance with the variations of original recording current. The recorded signal can be
reproduced back by passing the same tape through a reproducing head where the
voltage is induced corresponding to the magnetic pattern on the tape. When the tape is
passed through the reproducing head, the head detects the changes in the magnetic
pattern i.e. magnetization. The change in magnetization of particles produces change in
the reluctance of the magnetic circuit of the reproducing head, inducing a voltage in its
winding. The induced voltage depends on the direction of magnetization and its
magnitude on the tape.
Methods of Recording
The methods used for magnetic tape recording used for instrumentation purposes
are as follows:
i) Direct Recording
ii) Frequency Modulation Recording
iii) Pulse Duration Modulation Recording
For instrumentation purposes mostly frequency modulation recording is used. The pulse
duration modulation recording is generally used in the systems for special applications
where large number of slowly changing variables has to be recorded simultaneously.
3. i)Compare and Contrast the working, advantages and disadvantages of LED
and LCD.(N/D 2012)
Sl.No LED LCD
1. It consumes more power It consumes less power
2. Life time is more Life time is less

72
3. High cost www.rejinpaul.com

Low cost
4. Capable of generating its own light Requires an external or

internal light source
5. Emitting colour depends upon the material used Monochrome in nature
6. It emits light energy when energized It will alter the externally

available illumination
ii)Write a detailed note on LCD.(N/D2012)
Reflective twisted nematic liquid crystal display.

1. Polarizing filter film with a vertical axis to polarize light as it enters.
2. Glass substrate with ITO electrodes. The shapes of these electrodes will determine
the shapes that will appear when the LCD is turned ON.
3. Vertical ridges etched on the surface are smooth.
4. Glass substrate with common electrode film (ITO) with horizontal ridges to line up with
the horizontal filter.
5. Polarizing filter film with a horizontal axis to block/pass light.
6. Reflective surface to send light back to viewer. (In a backlit LCD, this layer is replaced
with a light source.)
A liquid crystal display (LCD) is a thin, flat electronic visual display that uses the light
modulating properties of liquid crystals (LCs). LCs do not emit light directly.

73
www.rejinpaul.com
They are used in a wide range of applications including: computer monitors, television,
instrument panels, aircraft cockpit displays, signage, etc. They are common in consumer
devices such as video players, gaming devices, clocks, watches, calculators, and
telephones. LCDs have displaced cathode ray tube (CRT) displays in most applications.
They are usually more compact,
lightweight, portable, less expensive, more reliable, and easier on the eyes.They are
available in a wider range of screen sizes than CRT and plasma displays, and since they
do not use phosphors, they cannot suffer image burn-in. LCDs are more energy efficient
and offer safer disposal than CRTs. Twisted nematic liquid crystal.

74
UNIT-V www.rejinpaul.com
TRANSDUCERS AND DATA ACQUISITION SYSTEMS
PART-A
1) Give any two applications of smart sensors. (April/may 2011)
Measuring exposures in cameras, optical angle encoder and optical arrays
2)Mention the need of ADC and DAC in Digital data Acquisition system. (Nov/Dec
2011)
ADCs are used to convert analog signals like the output from a temperature transducer,
a radio receiver or a video camera into digital signals for processing. Conversely, DACs
are used to convert digital signals back to analog signals
3) Give the factors to be considered in selecting a transducer.
Operating range, sensitivity, electrical output characteristics, errors, accuracy,
environmental conditions .
4) Define inverse transducer.
An inverse transducer is defined as a device which converts an electrical quantity
into a non – electrical quantity.
5) Define gauge factor.
The gauge factor is defined as the ratio of per unit change in resistance to per unit
change in length.
Gauge factor Gf = (ΔR/R) / (ΔL/L)
6) What is piezo-electric effect?
A piezo electric material is one in which an electric potential appears across
certain surfaces of a crystal if the dimensions of he crystal are changed by the
application of a mechanical force.
7) List any four force summing devices.(Nov/Dec 11)
 Bourdon tube
 Bellows
 Capsule
 Diaphragm
8) When do you call an instrument to be intelligent? (May/Jun 13)
The system can able to process and gives their output its own calibration by
sensing. Automatic operation done by all the system by using various sensors. These
systems are called intelligent.
75
www.rejinpaul.com
9) What is known as thermocouple effect & how do you use it in a
transducer?(May/Jun13)
It is a thermoelectric transducer which converts the thermal energy into an
electrical energy.
It is mostly used as primary transducer for temperature measurement where
thermocouple directly converts changes in temperature into an electrical signal.
Thermocouple comes under class of active transducer.
10) What is Transducer? (Dec 2010)
A transducer is a device which converts physical energy in to electrical energy.
Eg. LVDT , Strain guage, thermistor etc.
11) What are the materials used for piezoelectric transducers? (Dec 2009)
Some of the piezoelectric materials are
 Rochelle salt
 Ammonium Dihydrogen Phosphate (ADP)
 Quartz
12) What is an active transducer? (May 2010)
An active transducer generates an electrical signal directly in response to the
physical parameter and does not require external power source for its operation. Eg.
Tachogenerators, piezoelectric crystals
PART-B
1.Explain the classification and characteristics of transducer.
Transducers may be classified according to their structure, method of energy conversion
and application. Thus we can say that transducers are classified
• As active and passive transducer
• According to transduction principle
• As analog and digital transducer
• As primary and secondary transducer
• As transducer and inverse transducer
Active and Passive Transducer
Active Transducers
Active transducers are self-generating type of transducers. These transducers
develop an electrical parameter (i.e. voltage or current) which is proportional to the
quantity under measurement. These transducers do not require any external source or

76
www.rejinpaul.com
power for their operation. They can be subdivided into the following commonly used
types
Passive Transducers
Passive transducers do not generate any electrical signal by themselves. To obtain an

electrical signal from such transducers, an external source of power is essential. Passive
transducers depend upon the change in an electrical parameter (R, L, or C). They are
also known as externally power driven transducers. They can be subdivided into the
following commonly used types.
According to Transduction Principle
The transducers can be classified according to principle used in transduction.
• Capacitive transduction
• Electromagnetic transduction
• Inductive transduction
• Piezoelectric transduction
• Photovoltaic transduction
• Photoconductive transduction
Analog and Digital Transducers
77
The transducers can be classified on the basis ofwww.rejinpaul.com

the output which may be a
continuous function of time or the output may be in discrete steps.
Analog Transducers
These transducers convert the input quantity into an analog output which is a
continuous function of time.
Digital Transducers
Digital transducers produce an electrical output in the form of pulses which forms
an unique code. Unique code is generated for each discrete value sensed.
Primary or Secondary
 Some transducers consist of mechanical device along with the electrical device. In
such transducers mechanical device acts as a primary transducer and converts physical
quantity into mechanical signal. The electrical device then converts mechanical signal
produced by primary transducer into an electrical signal.
 Therefore, electrical device acts as a secondary transducer. For an example, in
pressure measurement Bourdons tube acts as a primary transducer which converts a
pressure into displacement and LVDT acts as a secondary transducer which converts
this displacement into an equivalent electrical signal.
Transducer and Inverse Transducer
Transducers convert non-electrical quantity into electrical quantity whereas
inverse transducer converts electrical quantity into non-electrical quantity. For example,
microphone is a transducer which converts sound signal into an electrical signal whereas
loudspeaker is an inverse transducer which converts electrical signal into sound signal.
Advantages of Electrical Transducers
1. Electrical signal obtained from electrical transducer can be easily processed (mainly
amplified) and brought to a level suitable for output device which may be an indicator or
recorder.
2. The electrical systems can be controlled with a very small level of power
3. The electrical output can be easily used, transmitted, and processed for the purpose of
measurement.
4. With the advent of IC technology, the electronic systems have become extremely
small in size, requiring small space for their operation.
5. No moving mechanical parts are involved in the electrical systems. Therefore there is
no question of mechanical wear and tear and no possibility of mechanical failure.

78
www.rejinpaul.com
Electrical transducer is almost a must in this modem world. Apart from the merits
described above, some disadvantages do exist in electrical sensors.
Disadvantages of Electrical Transducers

Ø The electrical transducer is sometimes less reliable than mechanical type because of
the ageing and drift of the active components.
Ø Also, the sensing elements and the associated signal processing circuitry are
comparatively expensive.
Ø With the use of better materials, improved technology and circuitry, the range of
accuracy and stability have been increased for electrical transducers.
Ø Using negative feedback technique, the accuracy of measurement and the stability of
the system are improved, but all at the expense of increased circuit complexity, more
space, and obviously, more cost.
2) Explain the construction of RTD and thermistor with neat sketches.
Temperature Sensors
Temperature is one of the fundamental parameters indicating the physical condition of
matter, i.e. expressing its degree of hotness or coldness. Whenever a body is heat’
various effects are observed. They include
• Change in the physical or chemical state, (freezing, melting, boiling etc.)
• Change in physical dimensions,
• Changes in electrical properties, mainly the change in resistance,
• Generation of an emf at the junction of two dissimilar metals.
One of these effects can be employed for temperature measurement purposes. Electrical
methods are the most convenient and accurate methods of temperature measurement.
These methods are based on change in resistance with temperature and generation of
thermal e.m.f. The change in resistance with temperature may be positive or negative.
According to that there are two types
• Resistance Thermometers —Positive temperature coefficient
• Thermistors —Negative temperature coefficient
Construction of Resistance Thermometers
The wire resistance thermometer usually consists of a coil wound on a mica or ceramic
former, as shown in the Fig. The coil is wound in bifilar form so as to make it no

79
www.rejinpaul.com
inductive. Such coils are available in different sizes and with different resistance values
ranging from 10 ohms to 25,000 ohms.
Advantages of Resistance Thermometers

1. The measurement is accurate.
2. Indicators, recorders can be directly operated.
3. The temperature sensor can be easily installed and replaced.
4. Measurement of differential temperature is possible.
5. Resistance thermometers can work over a wide range of temperature from -20’ C to +
650° C.
6. They are suitable for remote indication.
7. They are smaller in size
8. They have stability over long periods of time.
Limitations of Resistance Thermometers
1. A bridge circuit with external power source is necessary for their operation.
2. They are comparatively costly.
Thermistors
Thermistor is a contraction of a term ‘ thermal-resistors’ .Thermistors are semiconductor
device which behave as thermal resistors having negative temperature coefficient i.e.
their resistance decreases as temperature increases.

80
www.rejinpaul.com
Construction of Thermistor
Thermistors are composed of a sintered mixture of metallic oxides, manganese,
nickel, cobalt, copper, iron, and uranium. Their resistances at temperature may range
from 100 to 100k. Thermistors are available in variety of shapes and sizes. Smallest in
size are the beads with a diameter of 0.15 mm to 1.25 mm. Beads may be sealed in the
tips of solid glass rods to form probes. Disks and washers are made by pressing
thermistor material under high pressure into flat cylindrical shapes. Washers can be
placed in series or in parallel to increase power dissipation rating. Thermistors are well
suited for precision temperature measurement, temperature control, and temperature
compensation, because of their very large change in resistance with temperature. They
are widely used for measurements in the temperature range -100 C to +100 C
Advantages of Thermistor
1. Small size and low cost.
2. Comparatively large change in resistance for a given change in temperature
3. Fast response over a narrow temperature range.
Limitations of Thermistor
1. The resistance versus temperature characteristic is highly non-linear.
2. Not suitable over a wide temperature range.
3. Because of high resistance of thermistor, shielded cables have to be used to minimize
interference.
Applications of Thermistor
1. The thermistors relatively large resistance change per degree change in temperature
2. The high sensitivity, together with the relatively high thermistor resistance that may be
selected [e.g. 100k .], makes the thermistor ideal for remote measurement or control.
Thermistor control systems are inherently sensitive, stable, and fast acting, and they
require relatively simple circuitry.

81
3. Because thermistors have a negative temperaturewww.rejinpaul.com

coefficient of resistance,
thermistors are widely used to compensate for the effects of temperature on circuit
performance.
4. Measurement of conductivity.
3) Explain in detail the principle, working and features of LVDT with neat sketch.
 An LVDT, or Linear Variable Differential Transformer, is a transducer that converts

a linear displacement or position from a mechanical reference (or zero) into a
proportional electrical signal containing phase (for direction) and amplitude information
(for distance).
 The LVDT operation does not require electrical contact between the moving part
(probe or core rod assembly) and the transformer, but rather relies on electromagnetic
coupling; this and the fact that they operate without any built-in electronic circuitry are
the primary reasons why LVDTs have been widely used in applications where long life
and high reliability under severe environments are a required, such as
Military/Aerospace applications.
 The LVDT consists of a primary coil (of magnet wire) wound over the whole length
of a non-ferromagnetic bore liner (or spool tube) or a cylindrical coil form. Two
secondary coils are wound on top of the primary coil for “long stroke” LVDTs (i.e. for
actuator main RAM) or each side of the primary coil for “Short stroke” LVDTs (i.e. for
electro-hydraulic servo-valve or EHSV).
 The two secondary windings are typically connected in “opposite series” (or
wound in opposite rotational directions). A ferromagnetic core, which length is a fraction
of the bore liner length, magnetically couples the primary to the secondary winding turns
that are located above the length of the core.

82
www.rejinpaul.com
 When the primary coil is excited with a sine wave voltage (Vin), it generate a
variable magnetic field which, concentrated by the core, induces the secondary
voltages (also sine waves).
 While the secondary windings are designed so that the differential output voltage
(Va-Vb) is proportional to the core position from null, the phase angle (close to 0
degree or close to 180 degrees depending of direction) determines the direction
away from the mechanical zero. The zero is defined as the core position where
the phase angle of the (Va-Vb) differential output is 90 degrees.
 The differential output between the two secondary outputs (Va-Vb) when the core
is at the mechanical zero (or “Null Position”) is called the Null Voltage; as the
phase angle at null position is 90 degrees, the Null Voltage is a “quadrature”
voltage.
 This residual voltage is due to the complex nature of the LVDT electrical model,
which includes the parasitic capacitances of the windings.
4) With block diagram, explain DAS in detail.

Definition
Data acquisition is the process of real world physical conditions and conversion of
the resulting samples into digital numeric values that can be manipulated by a computer.
Data acquisition and data acquisition systems (abbreviated with the acronym DAS)
typically involves the conversion of analog waveforms into digital values for processing.
The components of data acquisition systems include:
i) Sensors that convert physical parameters to electrical signals.

83
ii) Signal conditioning circuitry to convert sensor signals intowww.rejinpaul.com

a form that can be converted
to digital values.
iii) Analog-to-digital converters, which convert conditioned sensor signals to digital
values.
Explanation
Data acquisition is the process of extracting, transforming, and transporting data
from the source systems and external data sources to the data processing system to be
displayed, analyzed, and stored.
A data acquisition system (DAQ) typically consist of transducers for asserting and
measuring electrical signals, signal conditioning logic to perform amplification, isolation,
and filtering, and other hardware for receiving analog signals and providing them to a
processing system, such as a personal computer.
Data acquisition systems are used to perform a variety of functions, including
laboratory research, process monitoring and control, data logging, analytical chemistry,
tests and analysis of physical phenomena, and control of mechanical or electrical
machinery.
Data recorders are used in a wide variety of applications for imprinting various
types of forms, and documents.
Data collection systems or data loggers generally include memory chips or strip
charts for electronic recording, probes or sensors which measure product environmental
parameters and are connected to the data logger.
Hand-held portable data collection systems permit in field data collection for up-to-
date information processing.
Source
Data acquisition begins with the physical phenomenon or physical property to be
measured. Examples of this include temperature, light intensity, gas pressure, fluid flow,
and force. Regardless of the type of physical property to be measured, the physical state
that is to be measured must first be transformed into a unified form that can be sampled
by a data acquisition system.
The task of performing such transformations falls on devices called sensors. A
sensor, which is a type of transducer, is a device that converts a physical property into a
corresponding electrical signal (e.g., a voltage or current) or, in many cases, into a
corresponding electrical characteristic (e.g., resistance or capacitance) that can easily be
converted to electrical signal.

84
The ability of a data acquisition system to measurewww.rejinpaul.com

differing properties depends
on having sensors that are suited to detect the various properties to be measured. There
are specific sensors for many different applications.
DAQ systems also employ various signal conditioning techniques to adequately
modify various different electrical signals into voltage that can then be digitized using an
Analog-to-digital converter (ADC).
Transducer 1 Sensor 1
Transducer 2 Sensor 2
MUX A/D
Transducer 3
Sensor 3
Signals
 Signals may be digital (also called logic signals sometimes) or analog depending
on the transducer used. Signal conditioning may be necessary if the signal from the
transducer is not suitable for the DAQ hardware being used.
 The signal may need to be amplified, filtered or demodulated. Various other
examples of signal conditioning might be bridge completion, providing current or voltage
excitation to the sensor, isolation, and linearization.
 For transmission purposes, single ended analog signals, which are more
susceptible to noise can be converted to differential signals. Once digitized, the signal
can be encoded to reduce and correct transmission errors.
DAQ hardware
 DAQ hardware is what usually interfaces between the signal and a PC. It could be
in the form of modules that can be connected to the computer's ports (parallel, serial,
USB, etc.) or cards connected to slots (S-100 bus, Apple Bus, ISA, MCA, PCI, PCI-E,
etc.) in the mother board.
 Usually the space on the back of a PCI card is too small for all the connections
needed, so an external breakout box is required. The cable between this box and the

85
www.rejinpaul.com
PC can be expensive due to the many wires, and the required shielding DAQ cards
often contain multiple components (multiplexer, ADC, DAC, TTL-IO, high speed timers,
RAM).
 These are accessible via a bus by a microcontroller, which can run small
programs. A controller is more flexible than a hard wired logic, yet cheaper than a CPU
so that it is alright to block it with simple polling loops.
 The fixed connection with the PC allows for comfortable compilation and
debugging. Using an external housing a modular design with slots in a bus can grow
with the needs of the user.
 Not all DAQ hardware has to run permanently connected to a PC, for example
intelligent stand-alone loggers and oscilloscopes, which can be operated from a PC, yet
they can operate completely independent of the PC.
DAQ software
DAQ software is needed in order for the DAQ hardware to work with a PC. The
device driver performs low-level register writes and reads on the hardware, while
exposing a standard API for developing user applications. A standard API such as
COMEDI allows the same user applications to run on different operating systems, e.g. a
user application that runs on Windows will also run on Linux and BSD.
Advantages
 Reduced data redundancy
 Reduced updating errors and increased consistency
 Greater data integrity and independence from applications programs
 Improved data access to users through use of host and query languages
 Improved data security
 Reduced data entry, storage, and retrieval costs
 Facilitated development of new applications program
Disadvantages
 Database systems are complex, difficult, and time-consuming to design
 Substantial hardware and software start-up costs
 Damage to database affects virtually all applications programs

86
 www.rejinpaul.com
Extensive conversion costs in moving form a file-based system to a database
system
 Initial training required for all programmers and users
5. Explain the principle of operation a) Piezoelectric transducer.(16) (April/may

2011) (May/June 2013)
Piezoelectric Transducers
Piezoelectric transducers produce an output voltage when a force is applied to
them. They are frequently used as ultrasonic receivers and also as displacement
transducers, particularly as part of devices measuring acceleration, force and pressure.
In ultrasonic receivers, the sinusoidal amplitude variations in the ultrasound wave
received are translated into sinusoidal changes in the amplitude of the force applied to
the piezoelectric transducer. In a similar way, the translational movement in a
displacement transducer is caused by mechanical means to apply a force to the
piezoelectric transducer. Piezoelectric transducers are made from piezoelectric
materials. These have an asymmetrical lattice of molecules that distorts when a
mechanical force is applied to it. This distortion causes a reorientation of electric charges
within the material, resulting in a relative displacement of positive and negative charges.
The charge displacement induces surface charges on the material of opposite polarity
between the two sides. By implanting electrodes into the surface of the material, these
surface charges can be measured as an output voltage. For a rectangular block of
material, the induced voltage is given by:
V = kFd/A

87
 Where F is the applied force in g, A is the area ofwww.rejinpaul.com

the material in mm, d is the
thickness of the material and k is the piezoelectric constant. The polarity of the induced
voltage depends on whether the material is compressed or stretched.
 Where F is the applied force in g, A is the area of the material in mm, d is the
thickness of the material and k is the piezoelectric constant. The polarity of the induced
voltage depends on whether the material is compressed or stretched.
 Materials exhibiting piezoelectric behaviour include natural ones such as quartz,
synthetic ones such as lithium sulphate and ferroelectric ceramics such as barium
titanate. The piezoelectric constant varies widely between different materials.
 Typical values of k are 2.3 for quartz and 140 for barium titanate. Applying
equation (13.1) for a force of 1 g applied to a crystal of area 100 mm2 and thickness 1
mm gives an output of 23 µV for quartz and 1 .4 mV for barium titanate. The
piezoelectric principle is invertible, and therefore distortion in a piezoelectric material
can be caused by applying a voltage to it.
 This is commonly used in ultrasonic transmitters, where the application of a
sinusoidal voltage at a frequency in the ultrasound range causes a sinusoidal variation
in the thickness of the material and results in a sound wave being emitted at the chosen
frequency.
PART C(15 MARKS)
1. Give a short notes on smart sensors.(A/M2016)
A smart sensor is a sensor with local processing power that enables it to react to local
conditions without having to refer back to a central controller. Smart sensors are usually
at least twice as accurate as non-smart devices, have reduced maintenance costs and
require less wiring to the site where they are used. In addition, long-term stability is
improved, reducing the required calibration frequency.
The functions possessed by smart sensors vary widely, but consist of at least some of
the following:
Remote calibration capability Self-diagnosis of faults Automatic calculation of
measurement accuracy and compensation for random errors Adjustment for
measurement of non-linearity’s to produce a linear output Compensation for the loading
effect of the measuring process on the measured system.

88
Calibration capability www.rejinpaul.com

Self-calibration is very simple in some cases. Sensors with an electrical output can use a
known reference voltage level to carry out self-calibration. Also, load-cell types of sensor,
which are used in weighing systems, can adjust the output reading to zero when there is
no applied mass. In the case of other sensors, two methods of self-calibration are
possible, use of a look-up table and an interpolation technique. Unfortunately, a look-up
table requires a large memory capacity to store correction points. Also, a large amount of
data has to be gathered from the sensor during calibration. In consequence, the
interpolation calibration technique is preferable. This uses an interpolation method to
calculate the correction required to any particular measurement and only requires a small
matrix of calibration points (van der Horn, 1996).
Self-diagnosis of faults
 Smart sensors perform self-diagnosis by monitoring internal signals for evidence
of faults. Whilst it is difficult to achieve a sensor that can carry out self-diagnosis of all
possible faults that might arise, it is often possible to make simple checks that detect
many of the more common faults.
 One example of self-diagnosis in a sensor is measuring the sheath capacitance
and resistance in insulated thermocouples to detect breakdown of the insulation.
Usually, a specific code is generated to indicate each type of possible fault (e.g. a failing
of insulation in a device).
 One difficulty that often arises in self-diagnosis is in differentiating between normal
measurement deviations and sensor faults. Some smart sensors overcome this by
storing multiple measured values around a set-point, calculating minimum and
maximum expected values for the measured quantity.
 Uncertainty techniques can be applied to measure the impact of a sensor fault on
measurement quality. This makes it possible in certain circumstances to continue to use
a sensor after it has developed a fault.
 A scheme for generating a validity index has been proposed that indicates the
validity and quality of a measurement from a sensor (Henry, 1995).
Automatic calculation of measurement accuracy and compensation for random
errors
Many smart sensors can calculate measurement accuracy on-line by computing
the Mean over a number of measurements and analyzing all factors affecting accuracy.

89
www.rejinpaul.com
This averaging process also serves to greatly reduce the magnitude of random
measurement errors.
Adjustment for measurement non-linearities
In the case of sensors that have a non-linear relationship between the measured
quantity and the sensor output, digital processing can convert the output to a linear
form, providing that the nature of the non-linearity is known so that an equation
describing it can be programmed into the sensor.
General Architecture of smart sensor:

One can easily propose a general architecture of smart sensor from its definition,
functions. From the definition of smart sensor it seems that it is similar to a data
acquisition system, the only difference being the presence of complete system on a
single silicon chip. In addition to this it has on–chip offset and temperature
compensation. A general architecture of smart sensor consists of following important
components:
o Sensing element/transduction element,
o Amplifier,
o Sample and hold,
o Analog multiplexer,
o Analog to digital converter (ADC),
o Offset and temperature compensation,
o Digital to analog converter (DAC),
o Memory,
o Serial communication and

o Processor
The generalized architecture of smart sensor is shown below:

90
www.rejinpaul.com
 Architecture of smart sensor is shown. In the architecture shown A1, A2…An and
S/H1, S/H2…S/Hn are the amplifiers and sample and hold circuit corresponding to
different sensing element respectively.
 So as to get a digital form of an analog signal the analog signal is periodically

sampled (its instantaneous value is acquired by circuit), and that constant value is held
and is converted into a digital words. Any type of ADC must contain or proceeded by, a
circuit that holds the voltage at the input to the ADC converter constant during the entire
conversion time.
 Conversion times vary widely, from nanoseconds (for flash ADCs) to

microseconds (successive approximation ADC) to hundreds of microseconds (for dual
slope integrator ADCs). ADC starts conversion when it receives start of conversion
signal (SOC) from the processor and after conversion is over it gives end of conversion
signal to the processor. Outputs of all the sample and hold circuits are multiplexed
together so that we can use a single ADC, which will reduce the cost of the chip.
91
 Offset compensation and correction comprises ofwww.rejinpaul.com

an ADC for measuring a
reference voltage and other for the zero. Dedicating two channels of the multiplexer and
using only one ADC for whole system can avoid the addition of ADC for this.
 This is helpful in offset correction and zero compensation of gain due to

temperature drifts of acquisition chain. In addition to this smart sensor also include
internal memory so that we can store the data and program required.
2) i) Discuss any one method of A/D converter.(Nov/Dec14)

Analogue-To-Digital Converters
Important factors in the design of an analogue-to-digital converter are the speed of
conversion and the number of digital bits used to represent the analogue signal level.
The minimum number of bits used in analogue-to-digital converters is eight.
 The use of eight bits means that the analogue signal can be represented to a
resolution of 1 part in 256 if the input signal is carefully scaled to make full use of the
converter range.
 However, it is more common to use either 10 bit or 12 bit analogue-to-digital
converters, which give resolutions respectively of 1 part in 1024 and 1 part in 4096.
Several types of analogue-to-digital converter exist. These differ in the technique used
to effect signal conversion, in operational speed, and in cost.
 The simplest type of analogue-to-digital converter is the counter analogue-to-
digital converter, as shown in Figure 5.23. This, like most types of analogue-to-digital
converter, does not convert continuously, but in a stop-start mode triggered by special
signals on the computer’s control bus.
 At the start of each conversion cycle, the counter is set to zero. The digital counter
value is converted to an analogue signal by a digital- to-analogue converter (a
discussion of digital-to-analogue converters follows in the next section), and a

92
comparator then compares this analogue counter value www.rejinpaul.com

with the unknown analogue
signal. The output of the comparator forms one of the inputs to an AND logic gate.
 The other input to the AND gate is a sequence of clock pulses. The comparator
acts as a switch that can turn on and off the passage of pulses from the clock through
the AND gate. The output of the AND gate is connected to the input of the digital
counter.
 Following reset of the counter at the start of the conversion cycle, clock pulses are
applied continuously to the counter through the AND gate, and the analogue signal at
the output of the digital-to-analogue converter gradually increases in magnitude.
 At some point in time, this analogue signal becomes equal in magnitude to the
unknown signal at the input to the comparator. The output of the comparator changes
state in consequence, closing the AND gate and stopping further increments of the
counter. At this point, the value held in the counter is a digital representation of the level
of the unknown analogue signal.
2)ii)Explain the working of D/A converter with a neat diagram(Apr/May14)

Digital-To-Analogue (D/A) Conversion
Digital-to-analogue conversion is much simpler to achieve than analogue-to-digital
conversion and the cost of building the necessary hardware circuit is considerably less. It
is required wherever a digitally processed signal has to be presented to an analogue
control actuator or an analogue signal display device. A common form of digital-to-
analogue converter is illustrated in Figure 5.24. This is shown with 8 bits for simplicity of
explanation, although in practice 10 and 12 bit D/A converters are used more frequently.
This form of D/A converter consists of a resistor-ladder network on the input to an
operational amplifier

93
www.rejinpaul.com
V0 to V7 are set at either the reference voltage level Vref or at zero volts according to
whether an associated switch is open or closed. Each switch is controlled by the logic
level of one of the bits 0 – 7 of the 8 bit binary signal being converted. A particular switch
is open if the relevant binary bit has a value of 0 and closed if the value is 1. Consider for
example a digital signal with binary value of 11010100. The values of V7 to V0 are
therefore:
3.Explain about the characteristics and selection of transducers.
Characteristics of Transducer
1. Accuracy: It is defined as the closeness with which the reading approaches an
accepted standard value or ideal value or true value, of the variable being measured.
2. Ruggedness: The transducer should be mechanically rugged to withstand overloads.
It should have overload protection.
3. Linearity: The output of the transducer should be linearly proportional to the input
quantity under measurement. It should have linear input - output characteristic. -
94
www.rejinpaul.com
4. Repeatability: The output of the transducer must be exactly the same, under same
environmental conditions, when the same quantity is applied at the input repeatedly.
5. High output: The transducer should give reasonably high output signal so that it can
be easily processed and measured. The output must be much larger than noise. Now-a-
days, digital output is preferred in many applications;
6. High Stability and Reliability: The output of the transducer should be highly stable
and reliable so that there will be minimum error in measurement. The output must remain
unaffected by environmental conditions such as change in temperature, pressure, etc.
7. Sensitivity: The sensitivity of the electrical transducer is defined as the electrical
output obtained per unit change in the physical parameter of the input quantity. For
example, for a transducer used for temperature measurement, sensitivity will be
expressed in mV/’ C. A high sensitivity is always desirable for a given transducer.
8. Dynamic Range: For a transducer, the operating range should be wide, so that it can
be used over a wide range of measurement conditions.
9. Size: The transducer should have smallest possible size and shape with minimal
weight and volume. This will make the measurement system very compact.
10. Speed of Response: It is the rapidity with which the transducer responds to changes
in the measured quantity. The speed of response of the transducer should be as high as
practicable.
Selection of Transducer:
1.Operating range: The range of the transducer should be large enough to encompass
all the expected magnitudes of the measurand.
2.Sensitivity: The transducer should give a sufficient output signal per unit of measured
input in order to yield meaningful data.
3.Electrical output characteristics: The electrical characteristics of transducer viz.

output impedance, frequency response, and the response time of the transducer output
signal should be compatible with the recording device and the rest of the measuring
system equipment.
4.Environmental conditions: The transducer should be immune to environmental

conditions such as change in temperature, humidity, vibration and shock ,acceleration
and corrosive chemicals.

95
www.rejinpaul.com
5.Errors: The errors inherent in the operation of the transducer itself, or those errors
caused by environmental conditions of the measurement, should be small enough or
controllable enough that they allow meaningful data to be taken.
6.Accuracy: Accuracy of the transducer should be within the specified range so that
input in the specified range can be reliably measured.

96
www.rejinpaul.com

97
www.rejinpaul.com

98
www.rejinpaul.com

99
www.rejinpaul.com

100
www.rejinpaul.com

101
www.rejinpaul.com

102
www.rejinpaul.com

103
www.rejinpaul.com

104
www.rejinpaul.com

105
www.rejinpaul.com

106
www.rejinpaul.com

107
www.rejinpaul.com

108
www.rejinpaul.com

109
www.rejinpaul.com

110
www.rejinpaul.com

111
www.rejinpaul.com

112
www.rejinpaul.com

113
www.rejinpaul.com

114
www.rejinpaul.com

115
www.rejinpaul.com

116
www.rejinpaul.com

117
www.rejinpaul.com

118
www.rejinpaul.com

119
www.rejinpaul.com

120

EE8403 Notes PDF

Uploaded by

Copyright:

Available Formats

EE8403 Notes PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

EE8403 Notes PDF

Uploaded by

Copyright:

Available Formats

EE8403 - MI Visit & Downloaded From : www.LearnEngineering.

COMMON MINIMUM STUDY MATERIAL (MSM)

SUBJECT CODE: EE 6404

SUBJECT NAME: MEASUREMENTS AND INSTRUMENTATION

Regulation: 2013 Year and Semester: II/IV

5 J.Y. ANGELINE JEMINA AP SCADEC

downloaded from www.rejinpaul.com

Functional elements of an instrument – Static and dynamic characteristics – Errors in

UNIT II ELECTRICAL AND ELECTRONICS INSTRUMENTS 9

UNIT III COMPARISON METHODS OF MEASUREMENTS 9

DC and AC potentiometers, DC and AC bridges, transformer ratio bridges, self-balancing

UNIT IV STORAGE AND DISPLAY DEVICES 9

UNIT V TRANSDUCERS AND DATA ACQUISITION SYSTEMS 9

Classification of transducers – Selection of transducers – Resistive, inductive and

IMPORTANCE AND NEED OF SUBJECT

 To understand the physical principles of electrical and electronics based

COURSE OUTCOME (CO)

 A combined support vector machine –wavelet transform model for prediction of

CONTENT BEYOND SYLLABUS

 Nagman Instruments and Electronics (P) Ltd, Chennai.

downloaded from www.rejinpaul.com

DETAILED LESSON PLAN www.rejinpaul.com

Principle of analog & digital voltmeters, ammeters 2 11 T1

Dot matrix display 1 35 T1

Classification & Selection of transducers 1 37 T1,T2

Elements of data acquisition system 1 44 T1

D/A converters, Smart sensor 1 46 T1

downloaded from www.rejinpaul.com

TABLE OF CONTENTS www.rejinpaul.com

47 Smart sensors www.rejinpaul.com

downloaded from www.rejinpaul.com

7. What is drift? (Nov/Dec 2011) www.rejinpaul.com

1. Explain the functional elements of measurement system with neat block

Primary Variable Variable Data

downloaded from www.rejinpaul.com

Primary sensing element: www.rejinpaul.com

2. Explain the static characteristics of measurement system in detail.(APR

downloaded from www.rejinpaul.com

iii) Sensitivity www.rejinpaul.com

downloaded from www.rejinpaul.com

It is the degree of closeness with which a given value may www.rejinpaul.com

3. With a suitable illustration elaborate the significance of

downloaded from www.rejinpaul.com

downloaded from www.rejinpaul.com

downloaded from www.rejinpaul.com

5.A) i) Explain the dynamic characteristics of measurement system in detail.( MAY

this case the response of the measurement system beginswww.rejinpaul.com

a) Mean = (532+548+ 543+ 535+ 546+ 531+ 543+ 536)/8

PART C(15 Mark)

downloaded from www.rejinpaul.com

downloaded from www.rejinpaul.com

STATISTICAL EVALUATION OF MEASUREMENT DATA

downloaded from www.rejinpaul.com

Average deviation: www.rejinpaul.com

=d12+ d12+ d12+……. d12/n

When the number of observations is less than 20,

downloaded from www.rejinpaul.com

downloaded from www.rejinpaul.com

8.How we do the ballistic test? (Nov/Dec 2011) www.rejinpaul.com