40W Single Output with Battery Charger (UPS Function) DRC-40 series

Bauar t gepruft
Sicherheit

LPS
egel ma ge
od o s
be wac g

www.tuv.com
ID 2000000000

UL62368-1 BS EN/EN62368-1 IEC62368-1 TPTC004

■ Features ■ Applications
Universal AC input / Full range Security system
Protections: Short circuit / Overload / Over voltage Emergency lighting system
Battery low protection / Battery reverse polarity protection Alarm system
by fuse DC UPS system
Can be installed on DIN rail TS-35/7.5 or 15 •Central monitoring system
Alarm signal for AC OK and Battery low Access systems
(via TTL open collector, optional via relay)
Cooling by free air convection
Pass LPS
LED indicator for power on
100% full load burn-in test ■ GTIN CODE
MW Search: https://www.meanwell.com/serviceGTIN.aspx
3 years warranty

■ Description
DRC-40 is a 40W AC/DC DIN rail type security power supply series. In addition to the primary output, there
is a charger output with a smaller rated current, enabling the backup power supply application the security
access systems require. DRC-40 accepts the universal input between 90VAC and 264VAC, and supplies
13.8VDC and 27.6VDC at output, respectively. With the efficiency up to 87%, it can operate with air
convection cooling under -30 ℃ through 70 ℃ . In addition to the key protection features such as overload
protection, over voltage protection, battery low cut off, and battery reverse polarity protection (by fuse),
the alarm signal for AC OK and battery low signaling is provided, via TTL open collector output for the
standard model ( via relay contact output as the optional model), to facilitate the system design.

■ Model Encoding
DRC - 40 A

Output voltage
Output wattage
Series name

File Name:DRC-40-SPEC 2024-01-26

 40W Single Output with Battery Charger (UPS Function) DRC-40 series

SPECIFICATION
MODEL DRC-40A DRC-40B
OUTPUT NUMBER CH1 CH2 CH1 CH2
DC VOLTAGE 13.8V 13.8V 27.6V 27.6V
RATED CURRENT 1.9A 1A 0.95A 0.5A
CURRENT RANGE 0 ~ 2.9A -------- 0 ~ 1.45A --------
RATED POWER 40.02W 40.02W
RIPPLE & NOISE (max.) Note.2 120mVp-p -------- 200mVp-p --------
OUTPUT
VOLTAGE ADJ. RANGE CH1:12 ~ 15V CH1:24 ~ 30V
VOLTAGE TOLERANCE Note.3 ±1.0% -------- ±1.0% --------
LINE REGULATION ±0.5% -------- ±0.5% --------
LOAD REGULATION ±0.5% -------- ±0.5% --------
SETUP, RISE TIME Note.4 400ms, 50ms/230VAC 800ms, 50ms/115VAC at full load
HOLD UP TIME (Typ.) 50ms/230VAC 10ms/115VAC at full load
VOLTAGE RANGE 90 ~ 264VAC 127 ~ 370VDC [DC input operation possible by connecting AC/L(+), AC/N(-)]
FREQUENCY RANGE 47 ~ 63Hz
INPUT EFFICIENCY (Typ.) 86% 87%
AC CURRENT (Typ.) 0.8A/115VAC 0.6A/230VAC
INRUSH CURRENT (Typ.) COLD START 30A/115VAC 60A/230VAC
105 ~ 150% rated output power
OVERLOAD
Protection type : Hiccup mode, recovers automatically after fault condition is removed
PROTECTION CH1:14.49 ~ 18.63V CH1:28.98 ~ 37.26V
OVER VOLTAGE
Protection type : Shut down o/p voltage, re-power on to recover
BATTERY CUT OFF 10±0.5V 20±1V
AC OK Open collector output, CONTACT : AC OK ; CUT OFF : AC Fail ; max. rating : 50V/30mA
FUNCTION Open collector output, CUT OFF : Battery ; CONTACT : Battery Low ; max. rating : 50V/30mA
BATTERY LOW
Battery low voltage : < 11V Battery low voltage : < 22V
WORKING TEMP. -30 ~ +70℃ (Refer to "Derating Curve")
WORKING HUMIDITY 20 ~ 90% RH non-condensing
ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +85℃, 10 ~ 95% RH
TEMP. COEFFICIENT ±0.03%/℃ (0 ~ 55℃) on CH1 output
VIBRATION 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
SAFETY STANDARDS UL62368-1, TUV BS EN/EN62368-1, EAC TP TC 004, AS/NZS 60950.1 approved

SAFETY & WITHSTAND VOLTAGE I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC

EMC ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃/ 70% RH
(Note 5)
EMC EMISSION Compliance to BS EN/EN55032 (CISPR32) Class B, BS EN/EN61000-3-2,-3, EAC TP TC 020
Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11, BS EN/EN55035, BS EN/EN61204-3, light industry level,
EMC IMMUNITY
EAC TP TC 020
MTBF 2496.2K hrs min. Telcordia SR-332 (Bellcore) ; 536.6K hrs min. MIL-HDBK-217F (25℃)
OTHERS DIMENSION 40*90*100mm (W*H*D)
PACKING 0.3Kg; 42pcs/13.6Kg/0.82CUFT
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.
NOTE 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1μF & 47μF parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time.
5. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed
that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power
supplies.” (as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf )
6. Installation clearances : 40mm on top, 20mm on the bottom, 5mm on the left and right side are recommended when loaded
permanently with full power. In case the adjacent device is a heat source, 15mm clearance is recommended.
7. The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitude higher
than 2000m(6500ft).
※ Product Liability Disclaimer：For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx

File Name:DRC-40-SPEC 2024-01-26

 40W Single Output with Battery Charger (UPS Function) DRC-40 series

Block Diagram

AC OK
ALARM
Bat. Low
CIRCUIT

EMI FILTER POWER RECTIFIERS +V

I/P & &
RECTIFIER SWITCHING -V
FILTER
Bat. +

DETECTION Bat. -
CIRCUIT
PWM
O.L.P. Battery Charger
CONTROL
&
O.V.P. Back up Control

Derating Curve Static Characteristics

100
100
90
80
230VAC 80
Input only
60 70
LOAD (%)

LOAD (%)

60
40
50
20
40

-30 -20 0 15 30 40 50 55 60 70 (VERTICAL) 90 100 125 135 145 155 165 175 180 200 230 264

AMBIENT TEMPERATURE (℃) INPUT VOLTAGE (V) 60Hz

File Name:DRC-40-SPEC 2024-01-26

 40W Single Output with Battery Charger (UPS Function) DRC-40 series

Suggested Application
1.Backup connection for AC interruption
(1) Please refer to Fig1.1 for suggested connection.
The power supply charges the battery and provides energy to the load at the same time when AC mains is OK.
The battery starts to supply power to the load when AC mains fails.

A : 12V
B : 24V Load
Battery
+ - + -
Bat+ Bat- V+ V-

DC OK

+
+V ADJ

Fig 1.1 Suggested system connection

2.Alarm signal for AC OK and battery low

(1) Alarm signal is sent out through " AC OK " & " Battery Low " pins.(TTL open collector output is provided for standard model, and relay contact output is provided as
optional model.)
(2) An external voltage source is required for this function. The maximum applied voltage is 50V and the maximum sink current is 30mA. Please refer to Fig 2.2.
(3) Table2.1 explains the alarm function built in the power supply
Function Description Output of alarm
The signal is "Low" when the power supply turns ON. Low (0.3V max. at 30mA)
AC OK
The signal turns to be "High" when the power supply turns OFF. High or open (External applied voltage 50V max.)

The signal is "Low" when the voltage of battery is under A:11V, B:22V. Low (0.3V max. at 30mA)
Battery Low
The signal is "High" when the voltage of battery is above A:11V, B:22V. High or open (External applied voltage 50V max.)

Table 2.1 Explanation of alarm signal

AC OK (Battery low)

PIN6(PIN8)

R
V

PIN5(PIN7)

External voltage and R

(The max. Sink is 30mA and 50V)

Fig 2.2 Internal circuit of AC OK (Battery Low), via TTL open collector

File Name:DRC-40-SPEC 2024-01-26

 40W Single Output with Battery Charger (UPS Function) DRC-40 series

Mechanical Specification
Case No.962A Unit:mm

40
100
3.81×7

8 7 6 5 4 3 2 1
TB2

DC OK
+
+V ADJ
90

TB1
3 2 1

7.5 7.5

Terminal Pin No. Assignment (TB1):

Pin No. Assignment
1 AC/L or DC+
2 AC/N or DC-
3 FG

Terminal Pin No. Assignment (TB2):

Pin No. Assignment Pin No. Assignment
1 -V 4 Bat. -
2 +V 5,6 AC OK
3 Bat. + 7,8 Bat. Low

Installation Instruction

This series fits DIN rail TS35/7.5 or TS35/15.

For installation details, please refer to the Instruction manual.
35

ADMISSIBLE DIN rail:TS35/7.5 OR TS35/15

(For reference only. Not included with unit.)

Back View

Installation Manual
Please refer to : http://www.meanwell.com/manual.html

File Name:DRC-40-SPEC 2024-01-26