Thank you for purchasing the Meat‐o‐Matic meat cutting band saw.

This product is intended

for meat cutting and meat processing purposes. Before using the product check the list of
standard equipment listed below. Any shortages must be reported to the relative dealer
within 7 working days.

STANDARD EQUIPMENT

1. 1980 x 16 x 5T Butcher bright blade fitted on saw

2. ,75kw 4‐pole Electric motor
3. Stainless steel work top
4. Thickness adjuster
5. Stainless steel sliding control
6. No.10 malleable casting mincer equipped with:
(i) No.10 mincer worm with point
(ii) Articetal mincer washer
(iii) No.10 mincer knife
(iv) No.10 mincer plate with 6mm holes
(v) No.10 kidney shaped mincer plate
(vi) No.10 sausage filler (22mm)
(vii) Top blade guide complete with brass guide

OPTIONAL ITEMS

1. Stand
2. No.10 mincer plates with 4,5mm, 8mm, 10mm and 13mm holes
3. No.10 sausage filler – 12mm and 16mm

TECHNICAL DATA

Cutting height ‐ 370mm

Cutting width ‐ 230mm
Mincer speed ‐ 386,5 RPM
Blade speed ‐ 293,7 MPM
Blade specs ‐ 1980 x 16 x 5T Butcher bright
Motor specs ‐ ,75kw high torque, 220V, 1400 RPM, 4‐pole, foot mounted
single phase, totally enclosed fan cooled
Body work ‐ Frame of 1,6mm gauge metal with centre plate of 3mm gauge
metal
Neck ‐ solid neck of 1,6mm gauge metal
Work top ‐ polished stainless steel

1
Paint work ‐ sandblasted and powder coated
Mincer specs ‐ No.10 from malleable casting (tin plated)
Mincer worm specs ‐ LM6 high silicone aluminium casting, polished for high
performance
Dimensions ‐ 100cm x 60cm x 43cm
Total weight ‐ 46kg

HANDY TIPS

1. Never use the meat cutting blade and the mincer simultaneously. It may put too
much strain on the motor and it is also dangerous when the blade is running while
mincing.
2. Always clean the band saw properly after use and store in a dry place.
3. Do not put pressure on the blade, guide the blade and let the blade do the work.
4. When replacing the blade make sure that the teeth face downwards
5. Always use a butcher bright blade – factory setting has been set accordingly.
6. Two M8 nuts are situated underneath the top pulley carrier plate (attached to the
neck). PLEASE DO NOT TAMPER WITH THESE NUTS AS YOU WILL ADJUST THE
FACTORY SETTING. Once the factory setting has been disturbed, you will most
probably find that the blade tends to run off the pulley and you might encounter
difficulty in re‐setting the blade tension.
7. VERY IMPORTANT!! When starting the machine, wait until the blade is running at full
revolutions before starting to operate. The same applies when using the mincer.
Never overload the mincer barrel, or feed the mincer with large chunks of meat.
8. No lubrication is required as the band saw is equipped with sealed bearings.
9. Never use the mincer without the articetal washer – this will cause damage to the
mincer.
10. Clean the mincer properly after use and lubricate with a little edible oil (e.g. olive oil)
to avoid rust
11. Before cleaning or execution of repair work of any kind, always ensure that the
electricity power supply is properly switched off, preferably by removing the plug
from the wall socket.
12. This product, like any other power tool, can do bodily harm and should be used with
proper caution.
13. When using the band saw, keep small children away.
14. Keep fingers away from all moving parts.

2
GUARANTEE

This product is guaranteed for a period of twelve months after purchase against any flaws in
material or defects in workmanship, providing that the product was used for its intended
function and returned to the manufacturer in its original packaging with proof of purchase
and the serial number. If the manufacturer finds that the machine was misused in any way,
the guarantee will no longer apply and the manufacturer accepts no responsibility for any
loss or resultant damages sustained. The manufacturer reserves the right to decide whether
any defect is the result of misuse, and to execute the guarantee accordingly. Any repairs
done under guarantee will be executed by the manufacturer, unless otherwise arranged by
the manufacturer and the relative customer or dealer. Any repairs as determined by the
manufacturer, not covered by the guarantee, will be effected at the expense of the
customer. It is the responsibility and at the customer’s own cost to arrange for the delivery
to and from the manufacturer’s premises for repair, unless otherwise arranged with the
manufacturer. The manufacturer is not responsible for any damages that may occur in third
party transit. The motor is separately guaranteed for 12 months by its suppliers on his own
terms,

PLEASE NOTE THAT BLADES AND BRASS BLADE GUIDES ARE CONSUMABLE PRODUCTS
AND THEREFORE IT IS NOT GUARANTEED.

3
 CABINET SPARES

1 01) MEAT – O - MATIC CABINET – M692/67

02) M8 BODY WASHER – M925/09

2 03) M8 x 35 COUNTER SUNK SCREWS – M915/7
04) M8 x 30 COUNTER SUNK SCREWS – M914/6
3 05) MINCER MOUNT POINT ONLY – M296/32
06) M8 NUTS – M142/16
07) 6003ZZ BEARING – M032/4

6
5

4
 CABINET SPARES

08) M8 x 20 SET SCREWS – M263/29

09) M8 NUTS – M142/16
10) M8 BODY WASHERS – M925/09
8 11) 6003ZZ BEARING – M032/4
12) BEARING HOLDER ONLY – M252/27

12
9

10

11

13 15 13) M8 NUTS – M142/16

16 14) M8 BODY WASHERS – M925/09
15) BOTTOM BRASS BLADE GUIDE STUD – M919/12
14 16) BRASS BLADE GUIDE – M919/11

17) 231mm BOTTOM FLAT PULLEY – M274/30

17
18) M8 x 20 GRUB SCREWS – M284/31

18

5
 CABINET SPARES

19 19) 231mm “V” PULLEY – M230/25

20) M8 x 20 GRUB SCREW – M284/31

20

21) MAIN DRIVE SHAFT WITH BUSHES – M219/24

22) M8 x 12 GRUB SCREW – M241/26
21
23) STEP BUSHES – M905/1

22

22 23

6
 NECK SPARES

24) TOP PULLEY COVER – M920/12

25) M8 FLAT WASHERS – M494/51
24
26) M8 THUMB SCREWS – M925/02

25

26

27 27) NECK – M648/63

28) 6300ZZ BEARINGS – M032/5
29) CIRCLIP 35mm INTERNAL – M043/5
30) 231mm TOP FLAT PULLEY ONLY – M021/3
28

29

30

7
 NECK SPARES
32 31) TENSION KNOB – M925/03
31
32) CLAMP FOR HANGER HOLDER – M921/14
33) TOP BRASS BLADE GUIDE HOLDER (OUTER) – M918/11
34) M8 x 60 SET SCREW – M925/01
33 35) BRASS BLADE GUIDE – M919/11
36) TOP BRASS BLADE GUIDE HOLDER (INNER) – M918/12
34 37) M8 NUT – M142/16
38) M8 x 45 SET SCREW (ADJUSTING) – M925/06
36 39) M8 x 20 SET SCEW – M263/29
40) HANGER/HOLDER – M921/13
41) M6 x 16 CHEESE HEAD SCREWS – M925/08
37
42) M6 NUTS – M925/13
35 43) M6 THUMB SCREW – M670/65
38

39
41

40
42

43

44) 1980mm x 16 x 5T BUTCHERS BLADE – L0001

44

8
 ,75 ELECTRIC MOTOR SPARES

48

45

46

47
49

51
50

52

57
54

53
55 56

45) ,75KW 220V ELECTRIC MOTOR – M450/42

46) M8 x 20 GRUB SCREWS – M284/31
47) 62mm “V” PULLEY – M472/49
48) “V” BELT A13 x 950 – M483/50
49) SHORT CABLE – M516/54
50) GROMMET – M527/54
51) ROCKER SWITCH – M505/52
52) M8 FLAT WASHERS – M494/51
53) M8 x 25 SET SCREWS – M925/05
54) M8 NUTS – M142/16
55) STARTING CAPACITOR – M461/49
56) RUNNING CAPACITOR – M461/48
57) ELECTRIC CORD COMPLETE WITH PLUG – M516/53

9
 NO. 10 MINCER SPARES

58 58) MINCER BODY – M913/5

61
59) WORM WITH POINT – M912/4
59 60) MINCER WASHER – M917/9
61) WORM POINT – M395/41
60
62) MINCER RING – M911/3

62

63) MINCER KNIFE – M923/83

68 66 64
64) 4.5mm MINCER PLATE (OPTIONAL) – M416/43
65) 6mm MINCER PLATE (STANDARD) – M417/43
66) 8mm MINCER PLATE (OPTIONAL) – M418/43
67) 10mm MINCER PLATE (OPTIONAL) – M419/43
63
68) 13mm MINCER PLATE (OPTIONAL) – M420/43
69) KIDNEY SHAPE PLATE (STANDARD) – M924/84
65
67
69

70) 12mm SAUSAGE FILLER (OPTIONAL) – M426/45

71) 16mm SAUSAGE FILLER (OPTIONAL) – M427/45
71
72) 22mm SAUSAGE FILLER (STANDARD) – M428/45

72

70

10
 STAINLESS STEEL SPARES

73) WORKTOP ONLY – M725/70

73
74) LONG ROD – M747/72
75) M5 THUMB SCREWS – M703/68
76) POP RIVETS 4,8 x 10 – M758/73

74

76

75

77) SLIDING CONTROL – M735/81

77

78) THICKNESS ADJUSTER – M922/14

79) M6 THUMB SCREW – M670/65
78

79

11