1/2

CTM188 - PowerTech™ 10.5 L and 12.5 L Diesel Engines Level 6 Electronic

Fuel Systems With Lucas EUIs
Remove and Install High Pressure Regulating Valve

Remove and Install High Pressure Regulating Valve

RG11168-UN: High Pressure Regulating Valve

LEGEND:

A - Screen
B - O-Ring
C - High Pressure Regulating Valve
D - O-Ring
E - O-Ring
F - Fuel Temperature Sensor

1. Close fuel shut-off valve, if equipped.

2. NOTE:

On high fuel tank applications without fuel shut-off valve, fuel tank return line must be pinched
before disconnecting, then plugged,

Disconnect fuel tank return line from filter housing and drain fuel into clean container.

3. Open valve on water separator bowl and drain filter housing.

4. Remove fuel temperature sensor (F). See REMOVE AND INSTALL FUEL TEMPERATURE SENSOR in Group 110.

5. Remove high pressure regulating valve (C).

6. To remove screen (A), see REMOVE AND INSTALL 100 MICRON INTERNAL FILTER HOUSING SCREEN INSERT
next in this Group.

7. NOTE:

file:///C:/ProgramData/Service%20ADVISOR/Temp/CTM188_09001faa8006... 2019/12/21
 2/2

High pressure regulating valve is not repairable. Do not disassemble valve. If defective, replace
entire assembly.

Clean and inspect all parts. Replace all O-rings.

8. Install parts in reverse order.

If removed, install screen (A). See REMOVE AND INSTALL 100 MICRON INTERNAL FILTER HOUSING SCREEN
INSERT next in this Group.

Tighten regulating valve to specifications.

Item Measurement Specification

High Pressure Regulating Valve-to- Torque 14 N·m (124 lb-in.)

Filter Housing

9. Install fuel temperature sensor (F). See REMOVE AND INSTALL FUEL TEMPERATURE SENSOR in Group 110.

10. Add fuel to filter housing between minimum and maximum marks on housing. Fuel can be added by throttling the fuel
shut-off valve (if equipped), or by removing cover and adding fuel from a clean container.

DPSG,OUO1004,1014-19-20150709

file:///C:/ProgramData/Service%20ADVISOR/Temp/CTM188_09001faa8006... 2019/12/21
 1/2

CTM188 - PowerTech™ 10.5 L and 12.5 L Diesel Engines Level 6 Electronic

Fuel Systems With Lucas EUIs
Remove and Install 100 Micron Internal Filter Housing Screen Insert

Remove and Install 100 Micron Internal Filter Housing Screen Insert

RG11168-UN: High Pressure Regulating Valve

RG10358-UN: Remove Screen

LEGEND:

A - 100 Micron Screen

B - O-Ring
C - High Pressure Regulating Valve
D - O-Ring
E - O-Ring
F - Fuel Temperature Sensor
K - Allen Wrench with Rubber Band

1. Remove fuel temperature sensor (F). See REMOVE AND INSTALL FUEL TEMPERATURE SENSOR in Group 110.

file:///C:/ProgramData/Service%20ADVISOR/Temp/CTM188_09001faa8006... 2019/12/21
 2/2

Remove high pressure regulating valve (C). See REMOVE AND INSTALL HIGH PRESSURE REGULATING VALVE
earlier in this Group.

2. IMPORTANT:

If allen wrench is pushed too far into 10 micron screen during removal and installation, screen may be
damaged. Tie a rubber band (K) approximately 10 mm (3/8 in.) from end of allen wrench, as shown, to
prevent screen damage.

NOTE:

Screen is approximately 91 mm (3-5/8 in.) up in bore of filter housing. Use a long allen wrench.

Attach a rubber band (K) on end of 5 mm allen wrench and remove 10 micron screen (A) from filter housing.

3. Clean and inspect screen.

4. Using allen wrench with rubber band, install screen in filter housing and tighten to the following specification.

Item Measurement Specification

100 Micron Internal Filter Housing Torque 5 N·m (44 lb-in.)

Screen

5. Install pressure regulating valve parts (B—D). See REMOVE AND INSTALL HIGH PRESSURE REGULATING VALVE
earlier in this Group. Install fuel temperature sensor parts (E) and (F). See REMOVE AND INSTALL FUEL
TEMPERATURE SENSOR in Group 110.

DPSG,OUO1004,1030-19-20061219

file:///C:/ProgramData/Service%20ADVISOR/Temp/CTM188_09001faa8006... 2019/12/21
 1/1

CTM188 - PowerTech™ 10.5 L and 12.5 L Diesel Engines Level 6 Electronic

Fuel Systems With Lucas EUIs
Remove and Install Fuel Filter Check Valve

Remove and Install Fuel Filter Check Valve

RG10307-UN: Fuel Filter Check Valve

LEGEND:

A - O-Ring
B - Check Valve
C - O-Ring

1. Close fuel shut-off valve (if equipped).

2. Disconnect fuel line (shown disconnected) and remove check valve (B). Remove O-rings (A) and (C) from both ends
of check valve.

3. Install check valve in filter housing and tighten to specifications.

Item Measurement Specification

Fuel Filter Check Valve to Fuel Torque 33 N·m (24 lb-ft)

Filter Housing

4. Connect fuel line and tighten to specifications.

Item Measurement Specification

Fuel Line-to-Fuel Filter Check Valve Torque 24 N·m (18 lb-ft)

5. Open fuel shut-off valve.

DPSG,OUO1004,1016-19-20150709

file:///C:/ProgramData/Service%20ADVISOR/Temp/CTM188_09001faa8006... 2019/12/21
 1/1

CTM188 - PowerTech™ 10.5 L and 12.5 L Diesel Engines Level 6 Electronic

Fuel Systems With Lucas EUIs
Remove and Install Primer Pump

Remove and Install Primer Pump

RG10360-UN: Primer Pump

LEGEND:

A - Primer Pump
B - Adapter

1. Remove primer pump (A).

2. If required, remove adapter (B).

3. Clean and inspect parts.

4. Install primer pump and adapter with new O-rings and tighten to specifications.

Item Measurement Specification

Fuel Primer (Single Rail Fuel Torque 14 N·m (124 lb-in.)

System)

Fuel Primer-to-Fuel Filter Housing Torque 11 N·m (97 lb-in.)

Adapter (Single Rail Fuel System)

DPSG,OUO1004,1032-19-20061219

file:///C:/ProgramData/Service%20ADVISOR/Temp/CTM188_09001faa8006... 2019/12/21
 1/3

CTM188 - PowerTech™ 10.5 L and 12.5 L Diesel Engines Level 6 Electronic

Fuel Systems With Lucas EUIs
Remove and Install Single Rail Fuel Supply Pump

Remove and Install Single Rail Fuel Supply Pump

RG10289-UN: Fuel Supply Pump

RG10288-UN: Removing Fuel Supply Pump

LEGEND:

A - Supply Pump Outlet Line

B - Fitting
C - Fuel Supply Pump
D - Supply Pump Inlet Line
E - Fitting
F - Mounting Bracket

IMPORTANT:

file:///C:/ProgramData/Service%20ADVISOR/Temp/CTM188_09001faa8006... 2019/12/21
 2/3

Plug or cap all fuel system connections and passages as lines or components are removed to keep debris out
using JDG998 Fuel System Cap Plug Kit.

Remove Fuel Supply Pump

NOTE:

Fuel flow through cylinder head may vary by engine application. Supply pump (A) may be mounted as
shown with fuel entering the front left side of the cylinder head and exiting the back of the head. On some
machine applications, the fuel supply pump is rotated 180° and the fuel lines on cylinder head are
reversed, with fuel entering the back of the head and exiting the front left side of the head.

Add a reference mark (supply pump-to-cylinder head) and label fuel lines as they are disconnected, to
ensure correct reinstallation of supply pump.

1. Remove two fuel lines (A) and (D) connected to fuel supply pump. Cap all lines and fittings to keep debris out of fuel
system.

2. Remove four cap screws securing supply pump to mounting bracket (F) and remove pump. Remove and discard O-
ring.

3. NOTE:

Fuel supply pump is not serviceable; replace pump if determined to be defective.

Remove fittings (B) and (E) from pump and clean thoroughly if pump is to be replaced.

Install Fuel Supply Pump

1. Inspect the fuel supply pump drive pin. If the pin is worn or is able to be rotated, replace the drive pin. See Replace
Fuel Supply Pump Drive Pin in Section 02, Group 50 of CTM100.

2. Install fittings onto new pump using new O-rings. Tighten fittings securely.

3. Ensure that drive coupler set screw is tightened to specifications on supply pump drive shaft with end of shaft flush
with coupler ID. Check drive coupler on camshaft drive pin also; adjust as needed.

Item Measurement Specification

Fuel Supply Pump and Camshaft Torque 4 N·m (3 lb-ft)

Drive Coupler Set Screws

4. Position new rubber spider (vibration absorber) on drive coupler. Position new O-ring on face of supply pump.

5. If removed, apply AR54749 Soap Lubricant to new O-ring on supply pump mounting bracket (F) and install. Tighten
mounting bracket cap screws to specifications.

Item Measurement Specification

Fuel Supply Pump Mounting Torque 50 N·m (37 lb-ft)

Bracket Cap Screws

6. Install fuel supply pump with rubber spider properly meshed with coupler on rear of camshaft.

7. Install four cap screws and tighten to specifications.

Item Measurement Specification

Fuel Supply Pump-to-Bracket Torque 25 N·m (18 lb-ft)

8. IMPORTANT:

file:///C:/ProgramData/Service%20ADVISOR/Temp/CTM188_09001faa8006... 2019/12/21
 3/3

Before connecting ORFS fuel line fittings, be sure O-ring is correctly positioned in the groove of fitting.
Tighten fitting ONLY to specified torque. DO NOT OVERTIGHTEN.

Install two fuel lines and tighten to specifications.

Item Measurement Specification

Fuel Line ORFS Fittings Torque 24 N·m (18 lb-ft)

DPSG,OUO1004,1000-19-20150420

file:///C:/ProgramData/Service%20ADVISOR/Temp/CTM188_09001faa8006... 2019/12/21
 1/4

CTM188 - PowerTech™ 10.5 L and 12.5 L Diesel Engines Level 6 Electronic

Fuel Systems With Lucas EUIs
Remove and Install Electronic Unit Injectors (Single Rail Fuel System)

Remove and Install Electronic Unit Injectors (Single Rail Fuel System)

RG8279-UN: Unit Injector Clamp Screws

LEGEND:

A - Clamp Cap Screws

IMPORTANT:

Electronic unit injectors on dual rail fuel systems are different than injectors on single rail systems. Use the
appropriate injector for engine/fuel system applications. Additionally, early single rail fuel systems for engines
S.N. (— 29999) use different injectors than later single rail systems for engines S.N. (30000— ). Replace injector
with the same type removed. DO NOT intermix injectors. See parts catalog for correct applications.

IMPORTANT:

Whenever EUI is replaced, sleeve in cylinder head must be replaced also. See Replace Unit Injector Sleeve in
Cylinder Head Using JDG981 is Section 02 Group 020 of Base Engine manual.

1. Remove rocker arm cover. See REMOVE AND INSTALL ROCKER ARM COVER in CTM100, Section 02, Group 020.

2. Remove rocker arm shaft assembly. See REMOVE ROCKER ARM ASSEMBLY in CTM100, Section 02, Group 020.

3. Disconnect fuel lines and drain fuel from lines and fuel rail in cylinder head.

4. Reconnect lines (or install cap plugs from JDG998 Fuel System Cap Plug Kit) to keep debris out of fuel system.

5. Remove injector hold-down clamp cap screws (A).

file:///C:/ProgramData/Service%20ADVISOR/Temp/CTM188_09001faa8209... 2019/12/21
 2/4

6.
RG8280-UN: Position Prybar

RG8281-UN: Removing Unit Injector

LEGEND:

A - Hold-Down Clamp
B - Prybar

Pry upward on the injector hold-down clamp (A) against cylinder head using a prybar (B) as shown.

7. Remove injector and clamp from cylinder head. Label injector for installation in same cylinder location as removed.

8. Immediately plug injector bore with clean cap plug to keep debris out of fuel system.

9. Remove injector O-rings and discard.

10. Store injector in a clean, lint-free container.

Install Electronic Unit Injectors

1. NOTE:

If a failure of any valve train or injector component(s) was observed, ensure that all of the debris
from the failed component(s) has been removed from the engine.

Remove cap plug from injector bore in cylinder head. Clean entire sleeve using a clean, lint-free cloth wrapped around
a wooden stick.

2. Install new O-rings on unit injector body. Lubricate O-rings with clean engine oil or AMOJELL lubricant.

file:///C:/ProgramData/Service%20ADVISOR/Temp/CTM188_09001faa8209... 2019/12/21
 3/4

3. IMPORTANT:

Press on top of injector plunger with palm of hand to properly seat O-rings and center injector between
valve springs.

NOTE:

New EUI hold-down clamp cap screws have pre-applied sealant.

RG10249-UN: Injector Hold-Down Clamp Screws

RG9574-UN: Torque-Turn EUI

LEGEND:

A - Clamp Cap Screw

B - Ratchet Handle

Install unit injector with hold-down clamp into same cylinder as removed (solenoid outward toward exhaust manifold
side of engine at equal distance between exhaust valve springs). Apply LOCTITE ® 242 Thread Lock and Sealer to
used hold-down cap screw. Initially tighten cap screw to specifications.

Item Measurement Specification

Electronic Unit Injector Hold-Down Initial Torque 20 N·m (177 lb-in.)

Clamp Cap Screws

4. Mark head of cap screw (A) at twelve o'clock position (viewed from rear) using a paint stick.

5. Install 13 mm swivel socket on head of cap screw. Position ratchet handle (B) parallel with centerline of engine
camshaft/crankshaft.

Torque-turn cap screw to the following specification.

file:///C:/ProgramData/Service%20ADVISOR/Temp/CTM188_09001faa8209... 2019/12/21
Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING

NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
 4/4

Item Measurement Specification

Electronic Unit Injector Hold-Down Torque-Turn 90° Additional Rotation

Clamp Cap Screws

6. Remove socket from head of cap screw and verify that mark has been tightened/turned 90° from its original position.

7. IMPORTANT:

DO NOT use red or blue LOCTITE ® on solenoid studs. Bonding strength is too high for small studs,
making future removal impossible without twisting off stud.

RG10294-UN: Wiring Terminal Nuts

LEGEND:

A - Retaining Nuts

Reconnect injector solenoid wiring leads onto solenoid studs. Apply LOCTITE ® 222 Small Screw Thread Locker
(PM38653) to studs and tighten retaining nuts (A) to specifications.

Item Measurement Specification

Electronic Unit Injector Wiring Torque 2 N·m (18 lb-in.)

Harness Connector Nuts

8. Install valve bridges, push tubes, and rocker arm assembly. Adjust valve stem-to-bridge clearances. See INSTALL
ROCKER ARM ASSEMBLY in CTM100, Section 02, Group 020.

9. If removed or loosened, tighten all harness and line clamps to specifications.

Item Measurement Specification

Fuel Line Clamps Torque 5 N·m (44 lb-in.)

Electronic Unit Injector Harness-to- Torque 35 N·m (26 lb-ft)

Shaft Clamps

Electronic Unit Injector Wiring Torque 25 N·m (18 lb-ft)

Connector Bracket-to-Rear of Head

10. Adjust electronic unit injector preload as detailed later in this Group.

LOCTITE is a registered trademark of Loctite Corp. VP98307,000010A-19-20150324

file:///C:/ProgramData/Service%20ADVISOR/Temp/CTM188_09001faa8209... 2019/12/21
 1/3

CTM188 - PowerTech™ 10.5 L and 12.5 L Diesel Engines Level 6 Electronic

Fuel Systems With Lucas EUIs
Adjust Electronic Unit Injector Preload

Adjust Electronic Unit Injector Preload

RG8228A-UN: JDG971 Timing Pin in Camshaft

RG8227D-UN: JDG971 Timing Pin in Crankshaft

file:///C:/ProgramData/Service%20ADVISOR/Temp/CTM188_09001faa8006... 2019/12/21
 2/3

RG11165-UN: Camshaft Timing Slot

LEGEND:

A - JDG971 Timing Pin

B - JDG820 Flywheel Turning Tool
C - JDG971 Timing Pin
D - Single Timing Slot
E - Double Timing Slot

1. Remove plug from cylinder block and install JDG820 Flywheel Turning Tool (B).

2. IMPORTANT:

Timing pin MUST BE installed in slot of camshaft first. Then install second timing pin in crankshaft slot
by carefully rocking flywheel back and forth.

Rotate engine flywheel in running direction (counterclockwise as viewed from rear) until JDG971 Timing Pin (A)
engages single timing slot (D) in camshaft. The proper timing slot can be found by viewing camshaft timing lobe
through camshaft timing pin bore while rotating engine. The double timing slot (E) will be at approximately 11 o'clock
(viewed from rear of engine) when pin is installed in slot (D). This ensures that engine is locked at TDC of No. 1
cylinder's compression stroke. Intake and exhaust rocker arms on No. 1 cylinder should be loose.

3. Remove threaded plug from crankshaft timing hole below oil cooler and filter housing assembly.

4. IMPORTANT:

DO NOT insert timing pin full depth into cylinder block crankshaft timing hole when rotating engine
flywheel until double slot on camshaft timing lobe is at approximately 11 o'clock (viewed from rear of
engine) to avoid crankshaft counterweight bending timing pin.

Slightly move engine flywheel back and forth with turning tool until a second JDG971 Timing Pin (C) can be installed in
slot in crankshaft. This ensures that camshaft and crankshaft are in sync (properly timed).

If timing pin does not enter crankshaft timing slot, crankshaft is not properly timed with camshaft. Crankshaft MUST BE
timed to camshaft. See Check And Adjust Camshaft-To-Crankshaft Timing in the Base Engine manual.

file:///C:/ProgramData/Service%20ADVISOR/Temp/CTM188_09001faa8006... 2019/12/21
 3/3

5.
RG8270-UN: Unit Injector Adjusting Screw

LEGEND:

A - Lock Nut
B - Adjusting Screws

Loosen lock nut (A) and loosen cylinders Nos. 3, 5, and 6 injector rocker arm adjusting screws (B) to relieve tension.

6. Slowly tighten adjusting screw until rocker arm roller contacts camshaft lobe at 0.0 clearance.

7. Tighten adjusting screw an additional 1/2 turn (180°) to preload injector. Tighten adjusting screw lock nut to
specifications while holding adjusting screw stationary.

Item Measurement Specification

Electronic Unit Injector Adjusting Torque 65 N·m (48 lb-ft)

Screw Lock Nut

8. Remove both timing lock pins, rotate crankshaft one full revolution (360°) and pin crankshaft only. Engine will now be
locked at No. 6 TDC.

9. Set injector preload on cylinders Nos. 1, 2, and 4.

10. Install plug in timing pin hole in block and tighten to specifications.

Item Measurement Specification

Timing Pin Plug in Cylinder Block Torque 33 N·m (24 lb-ft)

RG,RG34710,263CONV-19-20150709

file:///C:/ProgramData/Service%20ADVISOR/Temp/CTM188_09001faa8006... 2019/12/21