DSO1060 Manual

Hantek ®
Hantek Electronic co.,Ltd.

No.177 zhuzhou road(huite industry city),
QingDao,China
DSO1000SERIES
HANDHELD SCOPEMETER
USER’S MANUAL
1060/1200/1600/1600H
www.hantek.com.cn
DSO1000 SERIES
USER’S MANUAL
1060 / 1200 / 1600 / 1600H

1060/1200/1600/1600H
Content
General Safety Notice …………………………………….…..3

Digital Scope Meters………………………..…………………4
CHAPTER 1: Getting Start…………………………………... 6
General Check………………………………………....7
User’s Interface……………………………………...…7
Input Connections………………………………….....12
Function Check……………………………………….13
To compensate probes…………………………….....14
To display a signal automatically…………………....15
Using the Scope Meter……………………………....16
CHAPTER 2: Operating Scope……………………………..19
Set Vertical System…………………………………...20
Set Horizontal System………………………………..36
Set Trigger System…………………………………...40
Save / Recall Waveforms and Setups……………...48
Utility Function………………………………………...52
Signal Measurement………………………………....63
Cursor Measurement…………………………….......66
IO Set.......................................................................70
CHAPTER 3: Using examples……………………………...73
CHAPTER 4: Multimeter………………………………….....81
CHAPTER 5: Troubleshooting……………………………...95
CHAPTER 6: Specifications………………………………...96
CHAPTER 7: Appendix...................................................100

DSO1000 SERIES
General Safety Notice

1. Safety Terms and Symbols
Terms in this manual:
These terms may appear in this manual:
WARNING: Warning statements identify conditions or practices that could result in injury
or loss of life.
CAUTION: Caution statements identify conditions or practices that could result in

damage to this product or other property.
Terms on the Product:

These terms may appear on the product:
DANGER: indicates an injury hazard may be immediately accessible.
WARNING: indicates an injury hazard may be not immediately accessible.
CAUTION: indicates that a potential damage to the instrument or other property

might occur.
Symbols on the Product:

These symbols may appear on the product:
Hazardous Refer to Protective Grounding Test

Voltage Instructions Earth Terminal Terminal Grounding
of Chassis Terrninal
2. General Safety Information
Carefully read the following safety information in order to avoid any personal injury
or damage on this product or any products connected with it. Review the following
safety precautions carefully before operate the device to avoid any personal injuries or
damages to the device and any products connected to it. To avoid potential hazards use
the device as specified by this user’s manual only.
■ To Avoid Fire or Personal Injury.
■ Use Proper Power adapter. Use only the power cord specified for this product
and certified for the country of use.

1060/1200/1600/1600H
■ Connect and Disconnect Properly. Do not connect or disconnect probes or test

leads while they are connected to a voltage source.
■ Connect and Disconnect Properly. Connect the probe output to the

measurement device before connecting the probe to the circuit under test. Disconnect
the probe input and the probe reference lead from the circuit under test before
disconnecting the probe from the measurement device.
■ Observe All Terminal Ratings. To avoid fire or shock hazard, observe all ratings
and markings on the product. Consult the product manual for further ratings
information before making connections to the product.
■ Use Proper Probe. To avoid shock hazard, use a properly rated probe for your
measurement.
■ Avoid Circuit or Wire Exposure. Do not touch exposed connections and

components when power is on.
■ Do Not Operate With Suspected Failures. If suspected damage occurs with the
device, have it inspected by qualified service personnel before further operations.
■ Provide Proper Ventilation. Refer to the installation instructions for proper

ventilation of the device.
■ Do not operate in Wet/Damp Conditions.
■ Do not operate in an Explosive Atmosphere.
■ Keep Product Surfaces Clean and Dry.
Digital Scope Meters

DSO1000 Series digital scope meters offer exceptional waveform viewing and
measurements in a compact, lightweight package. DSO1000 series is ideal for
production test, field service, research, design, education and training involving
applications of analog circuit tests and troubleshooting.
Product features:
■ Dual Channel, Bandwidth:
60MHz (DSO1060)
200MHz (DSO1200)
600MHz (DSO1600)
600MHz (DSO1600H)

DSO1000 SERIES
■ Maximum real-time sampling rate:

150MSa/s (DSO1060)
500MSa/s (DSO1200)
1GSa/s (DSO1600)
2GSa/s (DSO1600H)
■ Memory depth:
32K points (Single Channel), 16K points (Dual Channels)
■ Color TFT LCD, 320×240 pixels resolution.
■ USB storage and printing supports, firmware upgrade via USB interface.
■ Adjustable waveform intensity, more effective waveform viewing.
■ One-touch automatic setup, ease of use (AUTOSET).
■ 15 Waveforms, 15 setups, supports CSV and bitmap format.
■ 22 Automatic measurements.
■ Automatic cursor tracking measurements.
■ Waveform recorder, record and replay dynamic waveforms.
■ User selectable fast offset calibration.
■ Built-in FFT function, Frequency Counter.
■ Pass/Fail Function.
■ Addition, Subtraction, Multiplication and Division Mathematic Functions.
■ Advanced trigger types include: Edge, Pulse width,ALT,Video.
■ Multiple Language User Interface.
■ Pop-up menu makes it easy to read and easy to use.
■ Built-in multi-language help system.
■ Easy-to-use file system supports Multi-Language characters file name
input.
■ Selectable bandwidth limit:
DSO1060:20MHz
DSO1200:20MHz,100MHz
DSO1600:20MHz,100MHz,200MHz,350MHz
DSO1600H:20MHz,100MHz,200MHz,350MHz

1060/1200/1600/1600H
CHAPTER 1: Getting Start

This chapter covers the following topics:
■ General Check
■ Functional Check
■ The User Interface
■ Input Connections
■ To compensate probes
■ To display a signal automatically
■ Using the Scope Meter

DSO1000 SERIES
General Check
When you have got a new DSO1000 series scope meter, it is suggested that you should
perform a general inspection on the instrument according to the following steps:
■ Check the shipping container for damage:

Keep the damaged shipping container or cushioning material until the contents of the
shipment have been checked for completeness and the instrument has been checked
mechanically and electrically.
■ Check the accessories:
Accessories supplied with the instrument are listed in “Accessories” in this guide. If the
contents are incomplete or damaged,please notify our distributor at your local area or
the overseas sales dept.
■ Check the instrument:
In case there is any mechanical damage or defect, or the instrument does not operate
properly or fails performance tests, please notify our distributor at your local area or
the overseas sales dept.
User’s Interface
The first thing to do with a new scope meter is to know its front panel. This chapter
helps to be familiar with the layout of the keys and how to use them. Read this chapter
carefully before further operations.
Front Panel (Figure 1-1):

The buttons not only allow you to use some of the functions directly but also bring up the
manual keys on the screen, which enable the access to many measurement features
associated with advanced functions, mathematics, and reference or to run control
features.

1060/1200/1600/1600H
Figure 1-1 Scope Meter Front Panel

DSO1000 SERIES
Figure 1-2 Front Panel Description
Description
1. LCD Display
2. F1~F5: Sets or switch options for the menu
3. Arrow Keys
4. HORI: Shows Horizontal menu
5. TRIG: Shows Trigger menu
6. LEVEL: Adjust the trigger level
7. RUN/STOP: key for running or stopping the operation
8. AUTO: Be used for auto setting under the oscilloscope operation mode

1060/1200/1600/1600H
9. TIME/DIV: Decrease or Increase the time base

10. POSITION: Adjust the horizontal trigger position
11. CH2: Shows the CH2 menu
12. VOLTS: Decrease or Increase the voltage/div
13. CH1: Shows the CH1 menu
14. M/R: Shows the Math or REF menu
15. DMM Buttons: The DMM control buttons
16. DMM/SCOPE: Switch DMM or Scope function
17. MENU ON/OFF: Turn on/off the menu
18. SAVE RECALL: Shows SAVE or RECALL menu
19. MEAS: Shows Measurement menu
20. UTILITY: Shows Utility menu
21. CURSOR: Shows Cursor menu
Display screen
1 15 3 4 5 6 7 8
9
21
10
20 11
12
19 13
2
18 14
17
16
Figure 1-3 LCD Display screen
Description
1. Shows Brand
10
DSO1000 SERIES
2. Shows horizontal trigger time

3. Shows location of the current waveform in the memory
4. Shows the trigger position in the memory
5. Shows the trigger mode
6. Shows the trigger source
7. Shows the trigger level
8. Shows the power
9. The center of current waveform window
10. CH1 waveform
11. The trigger level symbol
12. The grid
13. CH2 waveform
14. Shows the time base
15. Shows running staturs
16. CH1/CH2
17. Shows the coupling
18. Shows the voltage/div
19. CH2 mark
20. CH1 mark
21. Shows the trigger position in current waveform window
11
1060/1200/1600/1600H
Input Connections
See the following Figure 1-4:
Figure 1-4 Input Connections
Description:
1. The power adapter is supplied for AC power supply and battery recharging.
2. Multi-meter input jacks, including four circular banana jacks .The four circular jacks
are used for voltage,resistance,mA range current and A range current inputs.
3. Multi-meter test lead.
4. Scope Meter probes.
5. Scope Meter input channels.
12
DSO1000 SERIES
Function Check
Perform this quick functional check to verify that your scope meter is operating correctly.
1. Turn on the instrument.

Use the power adapter designed for your scope meter only. Use a power source that
delivers 100 to 240 VACRMS, 50Hz. Turn on the scope meter.
2. Input a signal to a channel.

Set the attenuation switch on the probe to X10 and connect the probe to CH1 on the
scope meter.
To do this:
■ Align the slot in the probe connector with the key on the CH1 BNC connector.
■ Push to connect, and twist to the right to lock the probe in place.
■ Attach the probe tip and ground lead to the PROBE COMP connector.
Set the probe attenuation of the scope meter to 10X.To do this, push CH1→Probe→10X
.
Figure 1-5 Set the probe
3. Push the AUTO button. Within a few seconds, a square wave will display
(approximately 1 kHz 2 V peak- to- peak).
Turn off CH1 and turn on CH2, repeat steps 2 and 3.
13
1060/1200/1600/1600H
To compensate probes
Perform this adjustment to match the characteristics of the probe and the channel input.
This should be performed whenever attaching a probe to any input channel the first time.
1. From CH1 menu, set the probe attenuation to 10X (press CH1→Probe→10X).
Set the switch to X10 on the probe and connect it to CH1 of the scope meter.
When using the probe hook-tip, insert the tip onto the probe firmly to ensure proper
connection.
Attach the probe tip to the probe compensator connector and the reference lead to the
ground pin, Select CH1, and then press AUTO.
2. Check the shape of the displayed waveform.
Correctly Compensated
Over compensated
14
DSO1000 SERIES
Under Compensated
3. If necessary, use a non-metallic tool to adjust the trimmer capacitor of the probe for
the flattest square wave being displayed on the scope meter.
4. Repeat if necessary.
WARNNING: To avoid electric shock while using the probe, be sure the perfection of
the insulated cable, and do not touch the metallic portions of the probe head while it is
connected with a voltage source.
To display a signal automatically

The scope meter has an Auto feature that automatically sets up the scope meter to best
display the input signal. Using Auto requires signals with a frequency greater than or
equal to 50 Hz and a duty cycle greater than 1%.
Press the AUTO button, the scope meter turns on and scales all channels that have
signals applied, and it selects a time base range based on the trigger source. The trigger
source selected is the lowest numbered input that has a signal applied. The scope meter
has two-channels input . Connect a signal to the CH1 input.
1.Connect a signal to the scope meter.

2.Press AUTO.
The scope meter may change the current setting to display the signal. It will automatically
adjust the vertical and horizontal scaling, the trigger coupling, type, position, slope, level,
and mode settings.
15
1060/1200/1600/1600H
Using the Scope Meter

This part provides a step-by-step introduction to the scope functions. The introduction
does not cover all of the capabilities of the scope functions but gives basic examples to
show how to use the menus and perform basic operations.
Turn on the scope meter

Connect scope meter to AC power via a power adapter. (The scope meter can still work
with built-in Li-ion battery even without AC power supply.)
Turn the scope meter on by pressing down the power on/off key.
The instrument then performs Self-checking after power on. The welcome picture will
display on the screen when the system finishes Self-checking.
The scope meter is powered up in its last setup configuration.
Figure 1-6 The Login window
Menu Operation
The following example shows how to use the tools menus to select a function, as shown
in the following figure.
16
DSO1000 SERIES
Figure 1-7 The Menu
1. Press the MENU ON/OFF key to display the Function Menu on the bottom of the
screen and the corresponding optional settings on the bottom. Press MENU ON/
OFF again to hide the Function Menu.
2. Choose one key from F1 to F5 and press it to change function setting.
Set up the vertical system

1. Change the vertical setup and notice that each change affects the
status bar differently.
■ Change the vertical sensitivity with or button and notice the change in the
status bar.
2. Move the signal vertically.
■ The / button moves the signal vertically. Also notice that the channel symbol
on the left side of the display moves in conjunction with the button.
To set up the horizontal system

1. Change the time base.
17
1060/1200/1600/1600H
■ The or button changes the time base in a 1-2-5 step sequence, and displays
thevalue in the status bar.
2. Move signal horizontally.
■ The or button moves displayed signal horizontally on waveform window. It sets
the trigger point position.
Set up the trigger system

1. Change the trigger Level
■ The or button changes the trigger level. The trigger level value is displayed
at the top-right of the screen and a line is displayed showing the location of the trigger
level.
2. Change the trigger setup and notice these changes in the status bar.
■ Press TRIG button in the key panel.Choose one key from F1 to F5 and press it to
change function setting.
18
DSO1000 SERIES
CHAPTER 2: Operating Scope

The end user should know how to determine the system setup from the status bar of a
Scope Meter. This chapter will detail the scope meter function of the test tool.
■ Set Vertical System

■ Set Horizontal System
■ Set Trigger System
■ Save and Recall waveforms and setups
■ Utility Function
■ Measure Signal
■ Cursor Measure
19
1060/1200/1600/1600H
Set Vertical System

Each channel of Scope meter has its own independent operation menu and it will pop up
after pressing CH1 or CH2 button. The settings of all items in the menu are shown in the
table below.
To make vertical CH1 and CH2 settings, do the following:
1. Press the CH1 or CH2 button and then the function menu appears at the bottom of the
screen.
2. Select and press key from F1 to F5 keys to make different settings.
Now, you can find the menu that looks like the following figure 2-1.
The CH1 menu (Page 1/2)
The CH1 menu (Page 2/2)
The CH1 menu (Page 1/3)(not include DSO1060)
20
DSO1000 SERIES
Figure 2-1 The CH1 Menu
The following table describes the channel menu:

Menu Setting Description
ON Turn on Channel
Enable
OFF Turn off Channel
AC The dc component in the input signal is blocked
Coupling DC The ac and dc components of the input signal are allowed
GND Disconnect the input signal
1X
10X Select one according to the probe attenuation factor to
Probe 100X ensure correct vertical scale reading
1000X
Reset Set the vertical display position back to middle window

1/2
Go to the next menu page
2/2
Back to the previous menu page
Coarse Set Voltage range coarsely

Volt/Div
Fine Set Voltage range finely
ON Turn on the invert function
Invert
OFF Turn off the invert function
ON Turn on the BW 20M(not include DSO1060)
BW 20M
OFF Turn off the BW 20M
2/2
3/3
Go to the next menu (not include DSO1060)
Turn on the BW 100M(not include DSO1060)

BW 100M
Turn off the BW 100M
3/3 Go to the first menu(not include DSO1060)
21
1060/1200/1600/1600H
Turn on the BW Limit

BW Limit
Turn off the BW Limit
1. Change Volt/DIV
It is the default setting of Volts/Div in a 1-2-5-step sequence from 1mV/div,2mV/div,5mV/
div or 10mV/div, 20mV/div, 50mV/div,..., to 1V/div,2 V/div,5 V/div.
The Volt/DIV will be displayed in the status bar on the bottom of the screen.
Figure 2-2 Channel Volt/Div
Press CH1→Volt/Div→Coarse/Fine to Set Volt/Div range.
2. Set Channel Coupling

With CH1 taken for example, input a sine wave signal containing a dc offset.
Press CH1→Coupling→AC to set “AC” coupling. It will pass AC component but block the
DC component of the input signal.
The waveform is displayed as Figure 2-3
22
DSO1000 SERIES
Figure 2-3 Waveform Display
Press CH1→Coupling→DC, to set “DC” coupling. It will pass both AC and DC

components of the input signal.
The waveform is displayed as Figure 2-4.
23
1060/1200/1600/1600H
Press CH1→Coupling→GND, to set “GND” coupling, it disconnects the input signal.

The screen displays as Figure 2-5:
24
DSO1000 SERIES
3. Set Probe Attenuation

The scope meter allows adjusting the probe attenuation scale factor correspondingly
in the channel operation menu in order to comply with the probe attenuation scale.
The attenuation factor changes the vertical scaling of the scope meter so that the
measurement results reflect the actual voltage levels at the probe tip.
To change (or check) the probe attenuation setting, press the CH1 or CH2 button
(according to which channel in using). Toggle the Probe soft button to match the
attenuation factor of the probe.
This setting remains in effect until changes again.

Figure 2-6 Probe Setting
25
1060/1200/1600/1600H
4. Invert a waveform
The displayed waveform reverses 180 degrees relatively to the ground potential.
Press CH1 or CH2 → F5 → F3, to turn on/off the Invert.
Figure 2-7 Turn Invert off
26
DSO1000 SERIES
Figure 2-8 Turn Invert on
5. Set Band-Width Limit

With CH1 taken for example, input a signal containing high frequency component.
Press CH1→F5→F4→OFF, to set up bandwidth limit to “OFF” status. The scope meter
is set to full bandwidth and passing the high frequency component in the signal.
The waveform is displayed as Figure 2-9.
27
1060/1200/1600/1600H
Figure 2-9 Turn BW limit Off
Press CH1→F5→F4→ON, to set up bandwidth limit to “ON” status. It will reject the
frequency component higher than 20MHz.
Press CH1→F5→F5→F2→ON, to set up bandwidth limit to “ON” status. It will reject the
frequency component higher than 100MHz.This function is not used in DSO1060.
The waveform is displayed as Figure 2-10:
28
DSO1000 SERIES
Figure 2-10 Turn BW limit On
6. Math Setting
The mathematic functions include “add”, “subtract”, “multiply”, “division”, and “FFT” for
CH1 and CH2. The mathematic result can be measured by the grid and the cursor.
The mathematic window is displayed as figure 2-11.
The Math menu (Page 1/2)
Figure 2-11 The Math menu

The Math menu (Page 2/2)
29
1060/1200/1600/1600H
Figure 2-12 The Math menu
The Math menu setting table

ON Turn on math
Enable
OFF Turn off math
A+B Add source A and source B
A-B Subtract source B from source A
Operate AXB Multiply source B by source A
A/B Divide source A by source B
FFT Fast Fourier Transform
CH1
Source A Define CH1 or CH2 as source A
CH2
CH1
Source B Define CH1 or CH2 as source B
CH2
1/2
2/2
Coarse Set Voltage range coarsely

Volt/Div
Fine Set Voltage range finely
ON Invert the MATH waveform
Invert
OFF Waveform display normal
1x
Select one according the probe attenuation
10x
Probe factor to ensure a correct vertical scale
100x
reading
1000x
2/2
Addition, Subtraction, Multiplication,Division and FFT

In the Math function, use the addition, subtraction, multiplication,division and FFT to
operate and analyze the waveform.
The multiplication function window is displayed in figure 2-13
30
DSO1000 SERIES

Figure 2-13 The multiplication
7. FFT
The FFT (Fast Fourier Transform) process converts a time-domain signal into its
frequency components mathematically.
FFT waveforms are useful in the following applications:

■ Measure harmonic content and distortion in systems
■ Characterize noise in DC power supplies
■ Analyze harmonics in power lines
The FFT menu (Page 1/2)
The FFT menu (Page 2/2)
31
1060/1200/1600/1600H
Figure 2-14 The FFT menu

The FFT menu table
ON Turn on FFT
Enable
OFF Turn off FFT
Operate FFT Fast Fourier Transform
CH1
Source Define CH1 or CH2 as FFT source
CH2
Rectangle
Hanning
Window Select window for FFT
Hamming
Blackman
1/2
2/2
Vrms Set “Vrms” as vertical unit

Scale
dBVrms Set “dBVrms” as vertical unit
Full Display waveform in full screen
Display
Split Display waveform in split screen
2/2
Note:
1. Signals that have a DC component or offset can cause incorrect FFT waveform
component magnitude values. To minimize the DC component, choose AC Coupling
on the source signal.
2. To reduce random noise and aliases components in repetitive or single-shot events,
set the oscilloscope acquisition mode to average.
3. To display FFT waveforms with a large dynamic range, use the “dBVrms” scale. The
“dBVrms” scale displays component magnitudes using a log scale.
FFT Window
The scope meter provides four FFT windows. Each window is a trade-off between
frequency resolution and amplitude accuracy. It depends on the desired
32
DSO1000 SERIES
measurement and the source signals characteristics to determine the window to use.
Use the following guidelines to select the best window.
The FFT Window table

Window Features Best for measuring
Best frequency resolution and Transients or bursts, the signal
worst magnitude resolution.This levels before and after the
is essentially the same as no event are nearly equal.Equal-
Rectangle window. amplitude sine waves with fixed
frequencies. Broadband random
noise with a relatively slow
varying spectrum.
Better frequency, poorer Sine, periodic, and narrow-band
Hanning magnitude accuracy than random noise. Transients or
Rectangular. Hamming has bursts where the signal levels
Hamming slightly better frequency before and after the events are
resolution than Hanning. significantly different.
Best magnitude, worst frequency Single frequency waveforms, to
Blackman
resolution. Find higher order harmonics.
8. REF
Reference Waveforms are saved waveforms to be selected for display. The reference
function will be available after saving the selected waveform to non-volatile memory.
Press M/R button to display the Reference waveform menu.
Select menu Enable->ON to enter reference function window. The reference function
window is displayed in Figure 2-15.
33
1060/1200/1600/1600H
Figure 2-15 The reference function window
Internal
Press M/R → REF → InternaI and go to the following menu.
REF menu when using internal memory
Figure 2-16 The Internal menu
REF menu table when using internal memory

ON Turn on REF
Enable
OFF Turn off REF
CH1 Select CH1 as REF channel
Source CH2 Select CH2 as REF channel
MATH Select MATH as REF channel
34
DSO1000 SERIES
Internal Select memory location in scope

Location
External Select memory location out scope
Save Save REF waveform
Load Load REF waveform
REF menu table when using external memory

ON Turn on REF
Enable
OFF Turn off REF
Source
Internal Select inner memory location
Location
External Select outer memory location
1/2
External
Press M/R→REF→External and go to the following menu.
The External REF menu (Page 1/2)
Figure 2-17 The External menu
The External REF menu (Page 2/2)

Figure 2-18 The External menu
The External menu table

New File To create a file
Delete File To delete the chosen file
35
1060/1200/1600/1600H
Load To load a chosen file

Go to the Storage menu page
Display a Reference Waveform
Figure 2-19 Reference display
1. Press M/R button to show the reference waveform menu.

2. Press F2 to select the reference channel: CH1, CH2 or MATH.
3. Press F4 to save REF.
4. Press F5 to load an internal REF file.
5. Press F1 button to turn on REF.
Note:
The Reference function is not available in X-Y mode.
Set Horizontal System

The horizontal system changes the horizontal scale and position of waveforms. The
horizontal center of the screen is the time reference for waveforms. Changing the
horizontal scale causes the waveform to expand or contract with respect to the screen
36
DSO1000 SERIES
center.
Horizontal position changes the displayed waveform position, relative to the trigger point.
Press HORI button to show the horizontal system menu. The settings of this menu are
listed in the following table.
The Horizontal Menu
Figure 2-20 The Horizontal menu

The Horizontal Menu Table
Y–T Show the relative relation between vertical voltage and
horizontal time.
Time base X–Y Show CH1 value at X axis; CH2 value at Y axis.
In Roll Mode, the waveform display updates from right to
Roll left.
Pressing this button clears trigger offset and moves the
Reset
trigger point to the horizontal center of the screen.
ON Turn on ALT Mag
ALT Mag
OFF Turn off ALT Mag
ON Turn on the Holdoff time
Holdoff
OFF Turn off the Holdoff time
1. TIME/DIV
Use this button to select the horizontal time/div (scale factor) for the main.
Figure 2-21 The TIME/DIV button

2. POSITION
Press this button to adjust the horizontal position of all channel waveforms. The
resolution of this control varies with the time base.
Figure 2-22 The POSITION button

37
1060/1200/1600/1600H
1 2 3
Figure 2-23 The horizontal/Time base marks
Marks Indicator
1. The current running status.
2. The trigger position in the memory.
3. The current waveform window’s position in the memory.
4. The trigger position in the current waveform window.
5. The horizontal time base (main time base).
ALT Mag
The ALT Mag is a magnified portion of the waveform window. Use ALT Mag to locate
and horizontally expand part of the main waveform window for a more detailed (higher
horizontal resolution) analysis of signal. The ALT Mag time base setting cannot be set .
38
DSO1000 SERIES
Figure 2-24 ALT Mag Mode
Description:
1. Wave to be horizontally expanded.
2.The magnified Wave.
3.The time base of ALT Mag.
4.The main time base.
The following describes the ALT Mag display.

The screen is divides into two parts. The upper half displays the main waveform window
and the lower half displays an expanded portion of the main waveform window.This
expanded portion of the main window is called the ALT Mag window.Two blocks shadow
the upper half. The un-shadowed portion is expanded in the lower half. The key TIME/
DIV control the size and position of the ALT Mag. The symbol at the right bottom of the
screen means the main time base and the symbol on the center bottom means the ALT
Mag time.
X-Y Format
This format is useful for studying phase relationships between two signals. CH1 in the
39
1060/1200/1600/1600H
horizontal axis (X) and CH2 in the vertical axis (Y)
Figure 2-25 X-Y display format
The following modes or functions will not work in X-Y format.

■ Automatic Measurements
■ Cursor Measurements
■ REF and MATH Operations
■ Horizontal Position
■ Trigger Controls
Set Trigger System

The trigger determines when the scope meter starts to acquire data and display a
waveform. When a trigger is set up properly, it can convert unstable displays or blank
screens into meaningful waveforms.
When the scope meter starts to acquire a waveform, it collects enough data so that it can
draw the waveform to the left of the trigger point. The scope meter continues to acquire
data while waiting for the trigger condition to occur. After it detects a trigger, the scope
meter continues to acquire enough data so that it can draw the waveform to the right of
the trigger point.
40
DSO1000 SERIES
Trigger Modes
The scope meter provides four trigger modes: Edge, Pulse , Alternative and Video.
Edge: An edge trigger occurs when the trigger input passes through a specified
voltage level in the specified slope direction.
Pulse: Use this trigger type to catch pulses with certain pulse width.
Alternative: Trigger on non-synchronized signals.
Video: Trigger on video-synchronized signals.
Edge Trigger Setting

An edge trigger determines whether the oscilloscope finds the trigger point on the rising
or the falling edge of a signal. Select Edge trigger mode to trigger on rising edge, falling
edge .
Press TRIG → F1 → Edge button to show the edge trigger menu as the following
table.
The Edge trigger menu (Page 1/2)
The Edge trigger menu(Page 2/2)
Figure 2-26 The Edge trigger menu

The Edge Trigger Table
CH1
Source Define CH1 or CH2 as trigger signal
CH2
Rising
Slope Trigger on rising edge or falling edge
Falling
Auto Acquire waveform even no trigger occurred
Sweep Normal Acquire waveform when trigger occurred
Single When trigger occurs, acquire one waveform then stop
HF Reject ON/OFF Reject high frequency signals
41
1060/1200/1600/1600H
50% Set the trigger level to the center of the signal
Pulse Trigger Setting

Pulse trigger occurs according to the width of pulse. The abnormal signals can be
detected through setting up the pulse width condition.
Press TRIG → F1 → Pulse button to show the pulse trigger menu as the following table.
The Pulse Trigger menu (Page 1/2)
Figure 2-27 The Pulse Trigger Menu
The Pulse Trigger menu (Page 2/2)
Figure 2-28 The Pulse Trigger Menu
The Pulse Trigger Table (Page 1/2)

CH1
Source Define CH1 or CH2 as trigger signal
CH2
+More +Pulse width more than selecting pulse condition
+Less +Pulse width less than selecting pulse condtion
+Equal +Pulse width equal to selecting pulse condition
When
-More -Pulse width more than selecting pulse condition
-Less -Pulse width less than selecting pulse condition
-Equal -Pulse width equal to selecting pulse condition
Setting Value Set required pulse width
1/2

42
DSO1000 SERIES
The Pulse Trigger Table (Page 2/2)

2/2
Auto Acquire waveform even no trigger occurred

Sweep Normal Acquire waveform when trigger occurred
Single When trigger occurs, acquire one waveform and then stop
HF ON
Reject high frequency signals
Reject OFF
2/2
Note: The Pulse width adjust range is10ns ~ 10s. When the condition is met, it will
trigger and acquire the waveform.
ALT (Alternative) Trigger Setting

When alternative trigger is on, the trigger sources come from two vertical channels. This
mode can be used to observe two non-related signals. You can choose two different
trigger modes for the two vertical channels. The options are as follows: Edge, Pulse. The
info of the trigger level of the two channels will be displayed on the upper-right of the
screen.
See the ALT screen in figure 2-29.
Press TRIG → F1 → ALT button to show the ALT trigger menu as the following table.
The ALT Trigger menu (Type Edge)(Page 1/2)
Figure 2-30 The ALT trigger menu
The ALT menu table (Type Edge)( Page 2/2)

CH1 Set trigger for CH1
Channel
CH2 Set trigger for CH2
43
1060/1200/1600/1600H
Edge
Type Set Edge/Pulse Trigger as the trigger type
Pulse
Rising Trigger on rising edge
Slope
Falling Trigger on falling edge
1/2

1 2 3 4 5
11
10
12
13 14
Figure 2-29 ALT Mode Screen

Description:
1. The trigger type of CH1
2. The horizontal trigger position of CH1
3. The trigger level value of CH1
4. The trigger type of CH2
5. The trigger level value of CH2
6. The time base of CH1
7. The trigger level of CH1
8. The trigger delay time of CH1
9. The horizontal trigger position of CH2
10. The time base of CH2
44
DSO1000 SERIES
11. The trigger level of CH2

12. The trigger delay time of CH2
13.The CH1 Voltage/Div
14.The CH2 Voltage/Div
Figure 2-31 The ALT Trigger menu
The Alternative menu table (Type edge)(Page 2/2)

2/2
ON
HF Reject Reject high frequency signals or not
OFF
2/2
The ALT Trigger menu (Type Pulse)(Page 1/2)
Figure 2-32 The ALT Tirgger menu
The Alternative menu table (Trigger Type: Pulse Page 1/2)

CH1 Set trigger mode for CH1
Channel
Edge
Type Set Edge/Pulse Trigger as the trigger type
Pulse
45
1060/1200/1600/1600H
+More +Pulse width more than selecting pulse condition

+Less +Pulse width less than selecting pulse condition
+Equal +Pulse width equal to selecting pulse condition
When
-More -Pulse width more than selecting pulse condition
-Less -Pulse width less than selecting pluse condition
-Equal -Pulse width equal to selecting pulse condition
1/2
The ALT Trigger menu (Type Pulse)(Page 2/2)
Figure 2-33 The ALT Trigger menu
The Alternative menu table (Trigger Type: Pulse Page 2/2)

2/2
Setting Value Set the width of the pulse

ON
HF Reject Reject high frequency signals or not
OFF
2/2
Video Trigger Setting (not include DSO1060)
The Video trigger mode is designed to captrue the video signal type to display stable
NTSC or PAL/SECAM standard composite video waveforms.
Press TRIG → F1 → Video button to show the Video trigger menu as the following
table.
The Video Trigger menu (Page 1/2)
46
DSO1000 SERIES
The Video Trigger menu (Page 2/2)
Figure 2-34 The Video Tirgger menu
The Video Trigger menu table

Channel
Applicable to the video signal of which the black level is
Normal
low
Polarity
Applicable to the video signal of which the black level is
Invert
high
All Field Set trigger on the falling edge of the first serration pulse
to field
Odd Field Set trigger on the falling edge of the first serration pulse
to odd field
Sync
Even Field Set trigger on the falling edge of the first serration pulse
to even field
Line Num Set trigger on the selected line in even field or odd field
All Lines Set trigger on the first line found
1/2
2/2
Line Num Set the lines of trigger video

PAL/SEC Set video standard to PAL/SEC
Standard
NTSC Set video standard to NTSC
47
1060/1200/1600/1600H
Force the oscilloscope to trigger in the absence condi-

Auto
ton
Let oscilloscope to trigger in the suitable trigger condi-
Sweep Normal
ton
Let osclloscope to trigger one time in the suitable trig-
Single
ger condition,then stop
2/2
Term interpretation
■ Auto:
This sweep mode allows the scope meter to acquire waveforms even when it does
not detect a trigger condition. If no trigger condition occurs while the scope meter is
waiting for a specific period (as determined by the time-base setting), it will force itself
to trigger.
When forcing invalid triggers, the scope meter cannot synchronize the waveform,
and the waveform seems to roll across the display. If valid triggers occur, the display
becomes stable on the screen. Any factor results in the un-stability of waveforms can
be detected by Auto Trigger, such as the output of Power supply.
NOTE: When horizontal control is set more than 50 ms/div, Auto mode allows the
oscilloscope to capture without trigger signal.
■ Normal:
The Normal mode allows the scope meter to acquire a waveform only when it is
triggered. If no trigger occurs, the scope meter keeps waiting, and the previous
waveform, if any, will remain on the display.
■ Single:
In Single mode, after pressing the RUN/STOP key, the scope meter waits for trigger.
While the trigger occurs, the scope meter acquires one waveform then stop.
Save / Recall Waveforms and Setups

Press the Save/Recall button, the interface menu for settings shows as follows.
The Save/Recall Menu Table
Wave Store or recall waveform
Setup Store or recall instrument setups
Type Bitmap Create or delete bitmap files
CSV Create or delete CSV files
Factory Recall factory setups
Internal Go to menu for internal memory operation
48
DSO1000 SERIES
External Go to menu for external memory operation
Wave
The Wave menu
Figure 2-35 The Wave menu

The Wave menu table
Setup
The Setup menu
Figure 2-36 The Setup menu
The Setup menu table

Bitmap
The Bitmap menu
49
1060/1200/1600/1600H
Figure 2-37 The Bitmap menu
The Bitmap menu table

CSV
The CSV menu
Figure 2-38 The CSV menu
The CSV menu table

Factory
The Factory menu
Figure 2-39 The Factory menu
The Factory menu table

50
DSO1000 SERIES
Load Recall factory setups or files
Internal Memory
Press SAVE/RECALL →Internal to go to the following menu

Setup_01
Internal ... Set up the location of files in internal memory
Setup_15
Recall waveform files and setup files from the
Load
internal memory location
Save waveform files and setup files to the internal
Save
memory location
External Memory
Press SAVE/RECALL → External to go to the following menu.

New File To create new file
Delete File Delete file
Recall waveform and setup from USB storage
Load
device
File system as following:
51
1060/1200/1600/1600H
Figure 2-40 File System
Factory
The scope meter has default settings and can be recalled at any time.
Memory location
Specify the memory location to save/recall the waveforms and setups.
Load
Recall saved waveforms, setups and default settings.
Save
Save waveforms and setups.
Note:
1. Select save stores not only the waveforms, but also the current scope meter.
2. The oscilloscope can store 15 settings permanently and can restore at any time.
Utility Function
52
DSO1000 SERIES
Press the Utility button to show the menu of the settings in the Utility system.
The series without RS232 and LAN:

The Utility menu (Page 1/4)
Figure 2-41 The Utility menu(without RS232 and LAN)
The series with RS232 and LAN:

53
1060/1200/1600/1600H
Figure 2-42 The Utility menu (with RS232 and LAN)
The Utility menu table (Page 1/4 and Page 1/5)

OFF Turn off Frequency or Counter
F/C Frequency Turn on Frequency
Counter Turn on Counter
ON Turn on the multimeter
DMM
OFF Turn off the multimeter
Display Show Display menu page
Acquire Go to the Acquire menu page

1/4
54
DSO1000 SERIES
1/5

2/4
2/5
Pass/Fail Go to Pass/Fail menu page

Record Go to Record menu page
Select languages
Language (More languages may be added in later firmware
versions.)
2/4
2/5


3/4
3/5
5Min
10Min
Shut
20Min Set the shut down time
Down
30Min
Infinite
ON
Sound Turn beeper sound on/off
OFF
Calibrate Calibrate the scope meter
3/4
55
1060/1200/1600/1600H
3/5

4/4
4/5
No Save Not save the system configuration when shut down

Configure
Save Save the system configuration when shut down
Update Update the system
System Info Show the information of the system
4/4
Go to the first previou menu page
4/5
The Utility menu table (Page 5/5)

5/5
IO Set Go to the IO Set menu Page

5/5
Go the the first previous menu page
Calibrate
The calibration adjusts the internal circuitry to get the best accuracy. Use these functions
to calibrate the vertical and horizontal systems.
For maximum accuracy at any time, run this calibration if the ambient temperature
changes by 5°C or more.
Before running this procedure, do these steps:

1. Disconnect any probes or cables from all channel inputs, otherwise failure or damage
to the scope meter may be occurred.
2. Push the Utility button and select Calibrate.
56
DSO1000 SERIES
The calibration screen is shown as in Figure 2-43.
Figure 2-43 The Calibration Screen
Note:
The scope meter must have been working or warm-up at least 30-minutes before
running calibration to get best accuracy.
The scope meter will calibrate parameter of vertical system (CH1, CH2).
Pass/Fail
The Pass/Fail function monitors changes of signals and output pass or fail signals by
comparing the input signal is within the pre-defined mask.
Press Utility→Pass/Fail to go to the following menu.

The Pass/Fail menu (Page 1/2)
57
1060/1200/1600/1600H
Figure 2-44 The Pass/Fail menu

The Pass/Fail menu (Page 2/2)
Figure 2-45 The Pass/Fail menu
The Pass/Fail menu table (Page 1/2)

ON Turn on Pass/Fail test
Enable
OFF Turn off Pass/Fail test
CH1 Select Pass/Fail test on CH1
Source
CH2 Select Pass/Fail test on CH2
Fail Output when Fail condition detected
Pass Output when Pass condition detected
Output
Fail+Beep Output and Beep when Fail condition detected
Pass +Beep Output and Beep when Pass condition detected
Stop Pass/Fail test stopped, press to run
Operate
Start Pass/Fail test running, press to stop
1/2

The Pass/Fail menu table (Page 2/2)

2/2
Stop ON Stop test when output occur

output OFF Continue test when output occur
Mask Go to Mask menu
2/2

Mask setting
58
DSO1000 SERIES
Press Utility→Pass/Fail→Mask Setting to go to the following menu.

The Mask menu (Page 1/2)
Figure 2-46 The Mask menu

The Mask menu (Page 2/2)
Figure 2-47 The Mask menu
The Mask setting menu table (Page 1/2)

Vertical Set vertical clearance to the waveform
Horizontal Set horizontal clearance to the waveform
Create Create a test mask according to the above clearance
Internal
Location Store created test mask into internal/External memory
External
1/2
The Mask setting menu table (Page 2/2) When the save as internal memory
2/2
Save Store created test mask into internal memory

Load Recall mask setting file from internal memory
The Mask setting menu (Page 2/2) When the save as external memory
59
1060/1200/1600/1600H

Save Go to save menu (same as REF save menu)
Load Recall mask setting file from external memory
Waveform Recorder
Waveform recorder records input waveforms from CH1 and CH2, with a maximum record
length of 1000 frames.
Press Utility→Record Setting to go to the following
Waveform recorder: Record the waveforms with specified interval.

The Recorder menu (Record Mode) (Page 1/2)
Figure 2-48 The Recorder menu (Record Mode)
The Recorder menu (Record Mode) (Page 2/2)
Figure 2-49 The Recorder menu (Record Mode)
The Record menu table (Record Mode) (Page 1/2)

Record Select record mode
Play Select play mode
Mode
Storage Select storage mode
OFF Turn off all recorder function
CH1
Source Select record source channel
CH2
End Frame <1-1000> Set number of record frames
Start Record stopped, press to start recording
Operate
Stop Press to stop recording
60
DSO1000 SERIES
1/2
The Record menu table (Record Mode) (Page 2/2)

2/2
Interval <10.0ms-20s> Set time interval between record frames

Back to the Utility menu page
Play : Play back the recorded waveforms.
The Record menu (Play Mode) (Page 1/2)
Figure 2-50 The Record menu (Play Mode)
The Record menu (Play Mode) (Page 2/2)
Figure 2-51 The Record menu (Play Mode)
The Record menu table (Play Mode) (Page 1/2)

Start Play stopped, press to start playback
Operate
Stop Press to stop playing
ON
Repeat Set repeat play mode or not
OFF
Interval <10.0ms-20s> Set interval time to play back
61
1060/1200/1600/1600H
1/2
The Record menu table (Play Mode) (Page 2/2)

2/2
Start Frame <1-1000> Set start frame

Cur Frame <1-1000> Select current frame to be played
End Frame <1-1000> Set End frame
Storage: Store recorded waveforms to non-volatile memory according to the setup

frames.
The Record menu (Storage Mode) (Page 1/2)
Figure 2-52 The Record menu (Storage Mode)
Figure 2-53 The Record menu (Storage Mode)

Start
<1-1000> Set first frame to be saved
Frame
62
DSO1000 SERIES
End Frame <1-1000> Set end frame to be saved

Internal
Location Set up Store location
External
1/2
The Record menu when the save to Internal memory (Storage Mode) (Page 2/2)
Save Save recorded waveform to internal memory location
Load Recall recorded waveform from internal memory location
Back to the Utility menu page
The Record menu when the save as external memory (Storage Mode) (Page 2/2)
Create File Create a new file
Delete File Delete a selected file
Load Recall recorded waveform from external memory location
Language:
DSO1000 series scope meters have multi-language user menu, choose as your desire.
Press Utility→Language to select the language.
Signal Measurement
Press the MEAS button to display the menu of the automatic measurements settings.
The Measure menu (Page 1/5)
Figure 2-54 The Measure menu
63
1060/1200/1600/1600H
Figure 2-58 The Measue menu
The scope meter provides 22auto measurements:Vpp,Vmax,Vmin,Vtop,Vmid,Vbase,Va

mp, Vavg, Vrms,Vcrms, Overshoot, Preshoot, Freq, Period, Rise Time, Fall Time, +Width,
-Width, +Duty, -Duty, Delay1->2↑, Delay1->2↓ (12 voltage and 10 time measurements).
The Measure menu table

64
DSO1000 SERIES
CH1 Select CH1 or CH2 as source

Source
CH2 channel for measurement
Voltage
Type Select to measure voltage parameter
Time
ON Turn on all measurement result
Meas All
OFF Turn off all measurement result
Clear Clear measurement result on screen
1/2
The Voltage Measurement menu table

Menu Description
Peak-to-peak = Max - Min
Pk to Pk
Measured over the entire waveform
Voltage of the absolute maximum level
Maximum
Voltage of the absolute minimum level
Minimum
Voltage of the statistical maximum level
Top
Voltage of the statistical minimum level
Base
Amp = Base - Top
Amplitude
RMS The Root Mean Square voltage over the entire waveform
Positive Overshoot = (Max - Top)/Amp x 100 %
Preshoot
Negative Overshoot = (Base - Min)/Amp x 100 %
Overshoot
Middle Voltage of the 50% level from base to top
Average Average voltage of a waveform
CRMS The Root Mean Square voltage over the first cycle in the waveform
The Time Measurement menu table

Menu Description
65
1060/1200/1600/1600H
Frequency Reciprocal of the period of the first cycle in the waveform

Period Time to take for the first signal cycle to complete in the waveform
Rising The time taken from lower threshold to upper threshold
Falling The time taken from upper threshold to lower threshold
+Width Measured of the first positive pulse in the waveform
-Width Measured of the first negative pulse in the waveform
Positive Duty Cycle = (Positive Pulse Width)/Period x 100%
+Duty
Measured of the first cycle in waveform
Negative Duty Cycle = (Negative Pulse Width)/Period x 100%
-Duty
Measured of the first cycle in waveform
Delay1->2↑ The delay of rising time between CH1 and CH2
Delay1->2↓ The delay of falling time between CH1 and CH2
Note: The results of the automatic measurements will be displayed on the bottom of
the screen. Maximum 3 results could be displayed at the same time. When there is no
room, the next new measurement result will make the previous results moving left out of
screen.
Cursor Measurement
The screen displays two parallel cursors. Move the cursors to make custom voltage
or time measurements of the signal. The values are displayed on the boxes below the
menu. Before using cursors, make sure to set the Signal Source as the channel for
measuring.
Press CURSOR to show the cursor menu as the following:
The Cursor menu
Figure 2-59 The Cursor menu
The Cursors menu table

66
DSO1000 SERIES
Manual Set to Manual Mode

Track Set to Track Mode
Mode
Auto Set to Auto Mode
OFF Turn off the cursor measure
Shown as vertical line to measure the horizontal
X
parameters
Type
Shown as horizontal line to measure the vertical
Y
parameters
CH1
Source CH2 Select the measurement signal source
MATH
Cursor A Select Cursor A or not
Cursor B Select Cursor B or not

The scope meter measures the Y or X coordinate values of the cursors, and the
increments between the two cursors.
To do cursor measurements, please do as the following steps:

1. Turn on the cursor measurement:
Cursor→Mode→Manual / Track / Auto.
2. Select channel Source for measurements by pressing soft button as:
Cursor→Source→CH1 / CH2 / MATH.
3. Select the cursors type by pressing soft button as Cursor→Type→ X or Y.
4. Press F4 or F5 to select the Cursor A or Cursor B.
5. Move the cursors to adjust the increment between the cursors.
The values will be automatically displayed on the right upper corner of screen when the
cursor function menu is hidden or displaying other menus.
Comments of Cursor Measurements
1. Auto Cursor Mode

The Auto Cursor Mode displays the cursors for the current measuring automatically. See
figure 2-60.
67
1060/1200/1600/1600H
Figure 2-60 The Automatic Cursor Mode
2. Manual Cursor Mode

In this mode, the scope meter measures the Y or X coordinate increments between the
two cursors. See figure 2-61.
1) Select menu Mode->Manual.
2) Select menu Type->X/Y to get the vertical or horizontal of Cursor A or Cursor B.
3) Select menu Source->CH1/CH2/MATH to Get the Cursor Source.
4 )Select Cursor A or Cursor B to adjust the increments between Cursor A and Cursor B.
5) Get the values between Cursor A and Cursor B.
delt x is the time between Cursor A and Cursor B.
1/(delt x) is the frequency between Cursor A and Cursor B.
68
DSO1000 SERIES
Figure 2-61 The Manual Cursor Mode
3. Track Cursor Mode

In Track Cursor Mode, the Cursor A and Cursor B move together with the selected
waveform. See figure 2-62.
69
1060/1200/1600/1600H
Figure 2-62 Track Cursor Mode
Please do the following steps:

1. Select menu Mode->Track.
2. Select Source for measurements. Select options as followings.
Cursor A->CH1/CH2. Cursor B->CH1/CH2.
3. Select Cursor A or Cursor B. Move the Select Cursors to adjust the increments
between the Cursors.
4. Get the values between Cursor A and Cursor B.
delt x is the time between Cursor A and Cursor B.1/(delt x) is the frequency between
Cursor A and Cursor B.delt y is the voltage between the Cursor A and Cursor B.
IO Set
Press UTILITY→ F5 → F5→ F5 → F5→ F2 button to show the menu of IO Set
The IO Set menu (LAN)
70
DSO1000 SERIES
Figure 2-63 The IO Set menu(LAN)
The IO Set menu table(LAN)

Setting Create a new LAN connection
Go to the Utility menu page
The IO Set menu(RS232)
Figure 2-64 The IO Set menu(RS232)
The IO Set menu table(RS232)

300
600
1200
Baud Rate Set Baud Rate parameter for RS232
2400
4800
9600
Go to the Utility menu page
Press the button F2 in the IO Set menu(LAN) ,then a small window pops up.
You can select the Arrow keys to move the cursor position in which you want to modify
parameter, then press the Enter key to pop up a soft key board by which you can set
what you want .
See the LAN setting window in Figure 2-65.
71
1060/1200/1600/1600H
Figure 2-65 the Lan Setting window
Press the button F2 in the IO Set menu(RS232),you can modify Baud Rate value.
See the IO Set menu (RS232) in Figure 2-64.
72
DSO1000 SERIES
Chapter 3 Using examples

Example 1: Simple Measurement
To acquire and display a signal, please do the steps as followings:
1. Connect signal to CH1 by using probe.
2. Press the key AUTO on key panel.
The Scope Meter set the vertical, horizontal, and triggers controls at the best status
automatically. Also, you can adjust the controls to meet your measurements to optimize
the waveform display.
To measure the frequency and Vpp, you can do these steps as followings:
1. Press the key MEAS , Select Source -> CH1 and select Type ->Voltage, then press
the key F5 and then press the key F2 to make a Pk to Pk test. The Vpp value will
display on the bottom of the waveform interface.
2. Press the key MEAS, select Source ->CH1and select type->Time, then Press the
key F5 and then press the key F2 to make a Frequency test. The Frequency value will
display on the bottom of the waveform interface.
3. Click the item Clear in the Measure menu, To clear the measurements on the
waveform interface.
See the measurements in the figure 3-1.
73
1060/1200/1600/1600H
Figure 3-1 The Vpp and Freq measurement Window
Example 2: The Application of the X-Y Operation

X-Y Plot acts to analyze correlation of data of two channels. Lissajous diagram
is displayed in the screen when you use X-Y Plot,which enables to compare
frequencies,amplitudes and phases of counterpart waveform against the reference
waveform. This makes it possible to compare and analyze frequency , amplitude and
phase between the input and output.
Do these steps as followings:

1. Set the probe attenuation to “x10”.Set the switch to”x10” on the probes.
2. Connect the CH1 probe to the input of the circuit, and connect the CH2 probe to the
output of the circuit.
3. Click the key AUTO on the panel.
4. Adjust the vertical scale and offset to display approximately the same amplitude
signals on each channel.
5. Select Time Base->X-Y format in Horizontal menu. The Scope Meter will display a
Lissajous pattern representing the input and the output characteristics of the circuit.
6. Adjust the scale and offset of the horizontal and vertical to a desirable waveform
display. The following picture shows a typical example.
7. Apply the Ellipse Method to observe the phase difference between the two channels.
74
DSO1000 SERIES
See Signal in X-Y Format in figure 3-2.
Figure 3-2 Signal in X-Y Format
Instruction of the Ellipse Method
75
1060/1200/1600/1600H
Sinθ = A/B or C/D, where θ = phase shift (in degrees) between the two signals.
From the formula above:
θ = ±arcsine (A/B) or ±arcsine (C/D)
θ must be in the range of (0~π/2) or (3π/2~2π) if the main axis of the ellipse is between
I and III quadrant, . If the main axis is at II and IV quadrant, θ must be in the range of
(π/2~π) or (π~3π/2).
Example 3: The FFT Cursor Measurements
FFT measurement includes: Amplitude measurement (Vrms or dBVrms) and the

Frequency measurement (Hz).
1. Press the key CURSOR to show Cursor menu.
2.Select Mode->Manual to enter the Manual Cursor Mode window.
3. Select Type->X/Y, select the Cursor Type to X or Y.
3. Select Source->MATH(FFT operation) in the Manual Cursor Mode window.
4. Drag the Cursor to the point of interest.
See the FFT Measurement (Cursor Type Y) in figure 3-3.

Figure 3-3 FFT Measurement (Cursor Type Y)

76
DSO1000 SERIES
See the FFT Measurement (Cursor Type X) in figure 3-4.

Figure 3-4 FFT Measurement (Cursor Type X)
Example 4: The Pass/Fail Test

The Pass/Fail Test is one of the enhanced special functions of the Scope Meter. By this
function, the Scope Meter could compare the input signal with the established waveform
mask. If the waveform “touches” the mask, a “Fail” signal occurs. Otherwise the test
passes. When needed, a programmable output can be used for external automatic
control applications. The output is built in as a standard feature and is optically isolated.
Do the steps as followings:
1. Press the key Utility to enter the Utility menu.
2. Press the key F5 in the panel to enter the page 2/4.
3. Select the Pass/Fail in the Utility menu to enter the Pass/Fail menu.
4. Select Enable to ON to turn on Pass/Fail, Select Source CH2 (the input source), select
Stop Output to OFF or ON in Page 2/2 of Pass/Fail menu.
5. Create the Pass/Fail Mask: Change the Vertical or Horizontal value by click the up or
down key in the panel to set the div of the vertical or horizontal values. Select Create
or Save or Load button if you need.
6. Select Operate to Start in Pass/Fail menu to start the Pass/Fail function.
77
1060/1200/1600/1600H
See the Pass/Fail window in figure 3-5.

Figure 3-5 The Pass/Fail Window
Example 5: Reduce the noise on a signal
See the signal with random noise in figure 3-6.
To reduce random noise, do the following steps:

1. Set the Probe and the channel attenuations to “x10”.
2. Connect the signal to the Scope Meter to display a stable wave.
3. Reduce the noise Select the Acquire Mode in Acquire menu.
If there is noise within the signal and the waveform looks too wide, in this case, choose
average acquisition. In this mode the waveform will be thin and easy to observe and
measure.
Use the Average following the steps:
1. Select Acquire in the Utility menu to enter the Acquire menu.
2. Select Mode to Average, then Press F2 to change the Averages form 2 to 128 to
switch the number of averages that best eliminates the noise from the
displayed waveform.
3. Select Mode to Normal to cancel this function.
78
DSO1000 SERIES
See signal after reducing random noise in figure 3-7.
Figure 3-6 Signal with random noise
79
1060/1200/1600/1600H
Figure 3-7 Signal afer reducing random noise
Example 6: Capture a Single signal
To capture a single event, it needs to gather some pre-test knowledge of the signal in
order to set up the trigger level and slope correctly. For example, if the event is derived
from TTL logic, a trigger level of 2 Volts should work on a rising edge.

1. Set the probe and the channel attenuations to 10X.
2. Press the key TRIG to show the Trigger menu.
3. Select Mode->Edge. Set Source to CH1 and Slope to Rising. Set Sweep to Single.
4. Adjust the Volts/Div and the time base in a proper range for the signal.
5. Drag the trigger level sign on the waveform display screen.
6. When the trigger conditions are met, data appears on the display representing the
data points that the Scope Meter obtained with one acquisition.
80
DSO1000 SERIES
CHAPTER 4: Multimeter
About this chapter
This chapter provides an introduction to the multimeter functions of DSO1000 Series.
The introduction gives guides to show how to use the menus and perform basic
measurements.
Connecting the Meter

Use the 4-mm safety banana jack inputs for the Meter functions: 10A , mA, COM,V/Ω/C.
Multimeter Operation Window
1
2
7 8 9
Figure 4-1 Multimeter operation window
Description
1) Battery electric quantity indictor.
2) Measurement mode indictors:
81
1060/1200/1600/1600H
DC: Direct electric measurement

AC: Alternating electric measurement
3)The symbol of Mutimeter current mode.
4) Manual/Auto range indictors, among which the MANUAL refers to measuring range
in manual operation mode and Auto means the measuring range in automatic
operation mode.
5) The reading value of measurement.
6) The bar graph indictor.
7) DC or AC Measurement mode control.
8) Absolute /relative magnitude measuring control: The sign “||” expresses the absolute
magnitude measuring control and “ ” represents the relative magnitude measuring
control.
9) Manually or automatically measuring range control.
Operating the Multimeter

If you are in the scope mode window, press OSC/DMM key, the scope meter will switch
to the multimeter mode window.Then the screen will display the measure mode window
that was in use the last time before you quit multimeter measure. When you switch to the
multimeter measurement the first time, the default measure mode is DC voltage mode.
Measuring Resistance Values

To measure a resistance, do the following:
1) Press the R key and then resistance measurement window appears on the screen.
2) Insert the black lead into the COM banana jack input and the red lead into the V/Ω/C
banana jack input.
3) Connect the red and black test leads to the resistor. The resistance value is shown on
the screen in Ohm.
Then, the screen will look like the following figure 4-2.
82
DSO1000 SERIES
Figure 4-2 Resistance Measurement
Making a Diode Measurement

To make a measurement on the diode, do the following:
1) Press the diode key and a diode symbol appears at the top of the screen. .
banana jack input.
3) Connect the red and black leads to the diode and the voltage value of the diode is
displayed on the screen in volt.
83
1060/1200/1600/1600H
Figure 4-3 Diode Measurement

To perform an On-off test, do the following:
1) Press the On-off key and then On-off indictor appears on the top of the screen.
banana jack input.
3) Connect the red and black leads to the tested points. If the resistance value of the
tested points is less than 30 Ω, you will hear beep sound from the test tool.
84
DSO1000 SERIES

Figure 4-4 On-off Measurement
Making a Capacitance Measurement

To measure a capacitance, do the following:
1) Press the C key and a capacitor symbol appears on the top of the screen.
banana jack input.
3) Connect the red and black leads to the capacitor and the capacitance value is
displayed on the screen in μF or nF.
85
1060/1200/1600/1600H
Figure 4-5 Capacitance Measurement
Making a DC Voltage Measurement
To measure a DC voltage, do the following:

1. Press the V key and DC appears at the top of the screen.
2. Insert the black lead into the COM banana jack input and the red lead into the V/Ω/C
banana jack input.
3. Connect the red and black leads to the measured points and the voltage value of
measured points is displayed on the screen.
Then ,the screen will look like the following figure 4-6.
86
DSO1000 SERIES
Figure 4-6 DC voltage Measurement
Making an AC Voltage Measurement

To measure the AC voltage, do the following:
1) Press the V key and DC appears on the screen.
2) Press the F1 key and AC appears on the screen.
banana jack input.
4) Connect the red and black leads to the measured points and the AC voltage value of
measured points will be displayed on the screen.
87
1060/1200/1600/1600H
Figure 4-7 AC voltage Measurement
Making a DC Current Measurement

To measure a DC current which is less than 600 mA , do the following:
1) Press the A key and then DC appears on the screen. The unit on the main reading
screen is mA. Press F2 to switch the measurement between mA and 10A. 600mA is
acquiescently.
2) Insert the black lead into the COM banana jack input and the red lead into the mA
banana jack input.
3) Connect the red and black leads to the measured points and the DC current value of
88
DSO1000 SERIES

Figure 4-8 DC current Measurement for 600 mA
To measure a DC current which is larger than 600 mA, do the following:

screen is mA.
2) Press F2 key to switch to 10A measurement, the unit on the main reading screen is A.
3) Insert the black lead into the COM banana jack input and the red lead into the 10A
banana jack input.
4) Connect the red and black leads to the measured points and the DC current value of
the measured points will be displayed on the screen.
5) Press F2 to return to 600 mA measurement.
89
1060/1200/1600/1600H
Figure 4-9 DC Current Measurement for 10A
Making an AC Current Measurement

To measure an AC current which is less than 600 mA, do the following:
screen is mA,and mA will display on the bottom of the screen, press F2 to switch the
measurement between mA and 10A. 600mA is acquiescently.
2) Press the F1 key once and AC will display on the bottom of the screen.
3) Insert the black lead into the COM banana jack input and the red lead into the mA
banana jack input.
4) Connect the red and black leads to the measured points and the AC current value of
90
DSO1000 SERIES
Figure 4-10 AC Current Measurement for 600 mA
To measure an AC current which is larger than 600 mA, do the following:

screen is mA.
2) Press F2 key to switch to10A measurement, the unit on the main reading screen is A.
3) Press the F1 key once and AC will display on the bottom of the screen.
4) Insert the black lead into the COM banana jack input and the red lead into the 10A
banana jack input.
5) Connect the red and black leads to the measured points and the AC current value of
the measured points will be displayed on the screen.
6) Press F2 to return to 600 mA measurement.
91
1060/1200/1600/1600H
Figure 4-11 AC Current Measurement for 10A
Taking a Relative Measurement

A currently measured result relative to the defined reference value is displayed in a rela-
tive measurement.
The following example shows how to take a relative measurement. At first, it is

required to acquire a reference value.
1) Press the Ω key.
banana jack input.
3) Connect the red and black test leads to the resistor. The resistance value is shown on
the screen in Ohm.
4) When the reading leveling off, press F1 key and then ||/△ is displayed on the top of
the screen. The saved reference value is displayed beside.
92
DSO1000 SERIES
Figure 4-12 Relative Measurement
Selecting Automatic/Manual Range Adjustment
The default range mode of the instrument is automatic range. Suppose you are
using the DC voltage mode, to switch to the manual range, perform the following
steps:
1) Press F3 key to enter the manual range mode and then Manual is displayed on the
top of the screen.
2) Under the manual range mode, the measuring range is increased by a stage when
pressing F4 key each time, and when reaching the highest stage, it jumps to the
lowest stage by pressing F4 key once again.
3) Press F3 key to switch back to the automatic range mode and then Auto is displayed
on the top of the screen.
Attention: capacitance measurement without manual range mode.
Then,the screen will look like the following figure 4-13.
93
1060/1200/1600/1600H
Figure 4-13 The Manual Range Mode
94
DSO1000 SERIES
Chapter 5: Troubleshooting
1.The scope meter cannot start.
1) Check the power cable connection.
2) Ensure the power switch is turned on.
3) After the above inspection, restart the scope meter.
4) If the problem still remains, please contact us for help.
2. The measurement result is 10 times higher or lower than the value expected.
Check if the probe attenuation is the same as the channel attenuation.
3. The waveform is displayed on the screen but is not stable under the scope
meter mode.
1) Check the Trigger Source and notice if it is set to the channel in use.
2) Check the Trigger Type.
4. When select the average sampling in the sampling mode or select a long
display time in the display mode under the scope meter, the display speed is
slow.
It is normal in the above case.
95
1060/1200/1600/1600H
Chapter 6: Specifications
Vertical
Channels 2
DSO1060: 60MHz
DSO1200: 200MHz
Bandwidth DSO1600: 600MHz
DSO1600H: 600MHz
DSO1060: 5.8ns
DSO1200: 1.7ns
Rise Time DSO1600: 0.58ns
DSO1600H: 0.58ns
Input Impedance Resistance: 1M;Capacitance: 15pF
DSO1060: 10mv/div to 5v/div
DSO1200: 10mv/div to 5v/div
Input Sensitivity DSO1600: 1mv/div to 5v/div
DSO1600H: 1mv/div to 5v/div
Input Coupling AC,DC with Ground Level Indicator
Vertical Resolution 8bits
Memory Depth 32k at single channel; 16k at dual channels
Maximum Input 300V(DC+AC Peak)
Horizontal
DSO1060: 150MSa/s
DSO1200: 500MSa/s
Sampling DSO1600: 1GSa/s
DSO1600H: 2GSa/s
Equivalent Sampling 50GSa/s
DSO1060: 5ns/div~1000s/div
Time Base
DSO1600H: 1ns/div~1000s/div
Time Base Precision ±50ppm
Trigger
96
DSO1000 SERIES
Source CH1,CH2
DSO1060: Edge, Pulse Width, Alternative

Mode
DSO1200,DSO1600,DSO1600H: Edge, Pulse Width, Alternative, Video.
X-Y Mode
X-Axis Input CH1
Y-Axis Input CH2
Phrase Shift Max.3 degree
Cursors and Measurement

Vpp,Vamp,Vmax,Vmin,Vtop,Vmid,VbaseVpp,Vamp,Vmax,Vmin,Vtop,Vmi
Voltage
d,Vbase,Vavg,Vrms,Vcrms,Preshoot,Overshoot
Frequency,Period,Rise time,Fall Time,Positive Width,Negative Width,Duty
Time
Cycle
Delay Delay 1->2↑, Delay 1-2↓
Cursor Manual,Track,Auto Measure Modes
Math Addition, Subtraction, Multiplication, Division, FFT
Storage 15 Waveforms and setups
Meter Mode
Maximum Resolution 6000 Counts
DMM Testing Modes Voltage,Current,Resistance,Capacitance,Diode & Continuity
Maximum Input Voltage AC : 600V DC : 800V

Maximum Input Current AC : 10A DC : 10A
Input Impedance 10MΩ
Meter Specification
97
1060/1200/1600/1600H
Range Accuracy Resolution

60.00mV 10uV
600.0mV 100uV
6.000V 1mV
DC Voltage ±1%±1digit
60.00V 10mV
600.0V 100mV
800V 1V
60.00mV 10uV
600.0mV 100uV
AC Voltage 6.000V ±1%±3digit 1mV
60.00V 10mV
600.0V 100mV
60.00mA ±1.5%±1digit 10uA
600.0mA ±1%±1digit 100uA
DC Current
6.000A 1mA
±1.5%±3digit
10.00A 10mA
60.00mA ±1.5%±3digit 10uA
600.0mA ±1%±1digit 100uA
AC Current
6.000A 1mA
±1.5%±3digit
10.00A 10mA
600.0 ±1%±3digit 0.1Ω
6.000K 1Ω
60.00K 10Ω
Resistance ±1%±1digit
600.0K 1 Ω
6.000M 1KΩ
60.00M ±1.5%±3digit 10KΩ
40.00nF 10pF
400.0nF 100pF
4.000uF ±1%±1digit 1nF
Capacitance 40.00uF 10nF
400.0uF 100nF
Attention:The smallest capacitance value that can be measured
is 5nF.
Diode 0V~2.0V
98
DSO1000 SERIES
Range Accuracy Resolution

On-off Test < 30Ω
Display
TFT LCD Type 5.7 Inch width LED Backlight Display
Display Resolution 240 (Vertical) X 320 (Horizontal) pixels
Interface
USB USB 2.0
Optional RS232,LAN
Power Source
AC 100V ~ 240V, 50Hz ~ 60Hz;
Line Voltage Range
DC Input:8.5VDC,1500mA
Battery Power(Installed) 6 hours(Li-ion Battery)
Mechanics
Dimension 245 x 163 x 52 (mm)
Weight 1.2 Kg
Other
GND Reference Scope meter and Multimeter Independence
Caution
Technical specifications may be jubject to variations without notice
99
1060/1200/1600/1600H
Chapter 7: Appendix
Appendix A: Accessories
1) Probe×2 (1.2m), 1:1, (10:1) Passive Probes

2) A Power Adapter that fits the standard of destination country
3) A User’s Guide
4) A User Registration Form
5) A User Warranty Card
6) A Software CD
Appendix B: Warranty
We warrant our products’ mainframe and accessories in materials within the warranty
period. During the period concerned,
We guarantee the free replacement or repair of products which are approved defective.
To get repair service or obtain a copy of the whole warranty statement, please contact
with your nearest sales and service office.
We do not provide any other warranty items except the one being provided by this sum-
mary and the warranty statement. The warranty items include but not being subjected to
the hinted guarantee items related to tradable characteristic and any particular purpose.
We will not take any responsibility in cases regarding to indirect, particular and ensuing
damage.
Appendix C: Maintenance
General Care
Do not store or leave the instrument in where the LCD display will be exposed to direct
sunlight for long periods of time.
Caution: To avoid damage to the instrument or probes, do not expose them to sprays,
liquids, or solvents.
Cleaning
If this instrument requires cleaning, disconnect it from all power sources and clean it with
a mild detergent and water. Make sure the instrument is completely dry before recon-
necting it to a power source.
To clean the exterior surface, perform the following steps:
1) Remove loose dust on the outside of the instrument and probes with a lint- free cloth.
Take care to avoid scratching the clear plastic display filter.
2) Use a soft cloth dampened with water to clean the instrument.
Notice: To avoid damage to the surface of the instrument or probes, do not use any
abrasive or chemical cleaning agents.
Storage of Scope meter
If the test tool is to be stored for a long time, it is required to charge the lithium battery
100
DSO1000 SERIES
before storage.
Charging the scope meter
The lithium battery is possibly not charged when delivery. To make the battery with
enough electric quantity, it must be charged for 4 hours (the test tool must be turned off
during charging). The battery can supply power for 6 hours after being charged com-
pletely.
To avoid superheat of battery during charging, the environment temperature is not al-
lowed to exceed the permissible value given in technical specification.
Note:
No hazard will occur even connecting the charger for a long time, e.g. during a whole
weekend. The instrument can automatically switch to slowly charging status.
Replacing the Lithium Battery Unit
It is usually not required to replace the battery unit. But when it is required to replace it,
only qualified personnel can carry out this operation, and only use the same specification
lithium battery.
101
1060/1200/1600/1600H
102

DSO1060 Manual

Uploaded by

Copyright:

Available Formats

DSO1060 Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

DSO1060 Manual

Uploaded by

Copyright:

Available Formats

Hantek ®

Hantek Electronic co.,Ltd.

General Safety Notice …………………………………….…..3

General Safety Notice

CAUTION: Caution statements identify conditions or practices that could result in

Terms on the Product:

WARNING: indicates an injury hazard may be not immediately accessible.

CAUTION: indicates that a potential damage to the instrument or other property

Symbols on the Product:

Hazardous Refer to Protective Grounding Test

■ To Avoid Fire or Personal Injury.

■ Connect and Disconnect Properly. Do not connect or disconnect probes or test

■ Connect and Disconnect Properly. Connect the probe output to the

■ Avoid Circuit or Wire Exposure. Do not touch exposed connections and

■ Provide Proper Ventilation. Refer to the installation instructions for proper

■ Do not operate in Wet/Damp Conditions.

■ Do not operate in an Explosive Atmosphere.

■ Keep Product Surfaces Clean and Dry.

Digital Scope Meters

■ Maximum real-time sampling rate:

CHAPTER 1: Getting Start

■ Check the shipping container for damage:

Front Panel (Figure 1-1):

Figure 1-1 Scope Meter Front Panel

Figure 1-2 Front Panel Description

9. TIME/DIV: Decrease or Increase the time base

Figure 1-3 LCD Display screen

2. Shows horizontal trigger time

Figure 1-4 Input Connections

1. Turn on the instrument.

2. Input a signal to a channel.

Figure 1-5 Set the probe

Turn off CH1 and turn on CH2, repeat steps 2 and 3.

To display a signal automatically

1.Connect a signal to the scope meter.

Using the Scope Meter

Turn on the scope meter

Figure 1-6 The Login window

Figure 1-7 The Menu

Set up the vertical system

To set up the horizontal system

Set up the trigger system

CHAPTER 2: Operating Scope

■ Set Vertical System

Set Vertical System

To make vertical CH1 and CH2 settings, do the following:

The CH1 menu (Page 2/2)

The CH1 menu (Page 1/3)(not include DSO1060)

The CH1 menu (Page 2/3)(not include DSO1060)

The CH1 menu (Page 3/3)(not include DSO1060)

Figure 2-1 The CH1 Menu

The following table describes the channel menu:

Reset Set the vertical display position back to middle window

Coarse Set Voltage range coarsely

Turn on the BW 100M(not include DSO1060)

3/3 Go to the first menu(not include DSO1060)

Turn on the BW Limit

Figure 2-2 Channel Volt/Div

Press CH1→Volt/Div→Coarse/Fine to Set Volt/Div range.