EFM8 Busy Bee Family

EFM8BB1 Data Sheet

The EFM8BB1, part of the Busy Bee family of MCUs, is a multi-

KEY FEATURES
purpose line of 8-bit microcontrollers with a comprehensive feature
set in small packages. • Pipelined 8-bit C8051 core with 25 MHz
maximum operating frequency
These devices offer high-value by integrating advanced analog and communication pe- • Up to 18 multifunction, 5 V tolerant I/O
ripherals into small packages, making them ideal for space-constrained applications. pins
With an efficient 8051 core, enhanced pulse-width modulation, and precision analog, the
• One 12-bit Analog to Digital converter
EFM8BB1 family is also optimal for embedded applications. (ADC)
EFM8BB1 applications include the following: • Two low-current analog comparators
• Integrated temperature sensor
• Motor control • Medical equipment
• 3-channel enhanced PWM / PCA
• Consumer electronics • Lighting systems
• Four 16-bit timers
• Sensor controllers • I/O port expander
• UART, SPI and SMBus/I2C
• Priority crossbar for flexible pin mapping

Core / Memory Clock Management Energy Management

CIP-51 8051 Core External CMOS High Frequency Internal LDO

Power-On Reset
(25 MHz) Oscillator RC Oscillator Regulator

Flash Program
RAM Memory Debug Interface Low Frequency
Memory Brown-Out Detector
(up to 512 bytes) with C2 RC Oscillator
(up to 8 KB)

8-bit SFR bus

Serial Interfaces I/O Ports Timers and Triggers Analog Interfaces Security

External 16-bit Analog 16-bit CRC

UART SPI Pin Reset PCA/PWM ADC
Interrupts Timers Comparators

I2C / SMBus General Purpose I/O Watchdog Timer Internal Voltage Reference

Lowest power mode with peripheral operational:

Normal Idle Shutdown

silabs.com | Building a more connected world. Rev. 1.6

 EFM8BB1 Data Sheet
Feature List

1. Feature List

The EFM8BB1 highlighted features are listed below.

• Core: • Timers/Counters and PWM:
• Pipelined CIP-51 Core • 3-channel programmable counter array (PCA) supporting
• Fully compatible with standard 8051 instruction set PWM, capture/compare, and frequency output modes
• 70% of instructions execute in 1-2 clock cycles • 4 x 16-bit general-purpose timers
• 25 MHz maximum operating frequency • Independent watchdog timer, clocked from the low frequen-
• Memory: cy oscillator
• Up to 8 kB flash memory, in-system re-programmable • Communications and Digital Peripherals:
from firmware. • UART
• Up to 512 bytes RAM (including 256 bytes standard 8051 • SPI™ Master / Slave
RAM and 256 bytes on-chip XRAM) • SMBus™/I2C™ Master / Slave
• Power: • 16-bit CRC unit, supporting automatic CRC of flash at 256-
• Internal LDO regulator for CPU core voltage byte boundaries
• Power-on reset circuit and brownout detectors • Analog:
• I/O: Up to 18 total multifunction I/O pins: • 12-Bit Analog-to-Digital Converter (ADC)
• All pins 5 V tolerant under bias • 2 x Low-current analog comparators with adjustable refer-
• Flexible peripheral crossbar for peripheral routing ence
• 5 mA source, 12.5 mA sink allows direct drive of LEDs • On-Chip, Non-Intrusive Debugging
• Clock Sources: • Full memory and register inspection
• Internal 24.5 MHz oscillator with ±2% accuracy • Four hardware breakpoints, single-stepping
• Internal 80 kHz low-frequency oscillator • Pre-loaded UART bootloader
• External CMOS clock option • Temperature range -40 to 85 ºC or -40 to 125 ºC
• Single power supply 2.2 to 3.6 V
• QSOP24, SOIC16, and QFN20 packages

With on-chip power-on reset, voltage supply monitor, watchdog timer, and clock oscillator, the EFM8BB1 devices are truly standalone
system-on-a-chip solutions. The flash memory is reprogrammable in-circuit, providing non-volatile data storage and allowing field up-
grades of the firmware. The on-chip debugging interface (C2) allows non-intrusive (uses no on-chip resources), full speed, in-circuit
debugging using the production MCU installed in the final application. This debug logic supports inspection and modification of memory
and registers, setting breakpoints, single stepping, and run and halt commands. All analog and digital peripherals are fully functional
while debugging. Each device is specified for 2.2 to 3.6 V operation and is AEC-Q100 qualified. Both the G-grade and I-grade devices
are available in 20-pin QFN, 16-pin SOIC or 24-pin QSOP packages, and A-grade devices are available in the 20-pin QFN package. All
package options are lead-free and RoHS compliant.

silabs.com | Building a more connected world. Rev. 1.6 | 2

 EFM8BB1 Data Sheet
Ordering Information

2. Ordering Information

EFM8 BB1 0 F 8 G – A – QSOP24 R

Tape and Reel (Optional)

Package Type
Revision
Temperature Grade G (-40 to +85), I (-40 to +125), A (-40 to +125, Automotive Grade)
Flash Memory Size – 8 KB
Memory Type (Flash)
Family Feature Set
Busy Bee 1 Family
Silicon Labs EFM8 Product Line

Figure 2.1. EFM8BB1 Part Numbering

All EFM8BB1 family members have the following features:

• CIP-51 Core running up to 25 MHz
• Two Internal Oscillators (24.5 MHz and 80 kHz)
• SMBus / I2C
• SPI
• UART
• 3-Channel Programmable Counter Array (PWM, Clock Generation, Capture/Compare)
• 4 16-bit Timers
• 2 Analog Comparators
• 12-bit Analog-to-Digital Converter with integrated multiplexer, voltage reference, and temperature sensor
• 16-bit CRC Unit
• AEC-Q100 qualified
• Pre-loaded UART bootloader

In addition to these features, each part number in the EFM8BB1 family has a set of features that vary across the product line. The
product selection guide shows the features available on each family member.

Table 2.1. Product Selection Guide

Digital Port I/Os (Total)
Ordering Part Number

Comparator 0 Inputs

Comparator 1 Inputs

Temperature Range
Flash Memory (kB)

(RoHS Compliant)
ADC0 Channels
RAM (Bytes)

Package
Pb-free

EFM8BB10F8G-A-QSOP24 8 512 18 16 8 8 Yes -40 to +85 C QSOP24

EFM8BB10F8G-A-QFN20 8 512 16 15 8 7 Yes -40 to +85 C QFN20

EFM8BB10F8G-A-SOIC16 8 512 13 12 6 6 Yes -40 to +85 C SOIC16

EFM8BB10F4G-A-QFN20 4 512 16 15 8 7 Yes -40 to +85 C QFN20

EFM8BB10F2G-A-QFN20 2 256 16 15 8 7 Yes -40 to +85 C QFN20

silabs.com | Building a more connected world. Rev. 1.6 | 3