Scribd Logo
Upload

Welcome to Scribd!

  • 27 views

    Tuffkote: Epigard Epoxy Finish Heat Resisting Lustrol Aluminium

    Uploaded by

    SHATABDI- DEL
    This document provides information on Heat Resisting Lustrol Aluminium, a two-part aluminum pigment paint with heat resistance up to 250°C. It can be used as a topcoat on chimneys, boilers, ducts, and industrial equipment. The paint has a bright metallic finish when dry and good chemical resistance to acids, alkalis, and solvents when properly coated. It is supplied in kits containing the aluminum paste and medium, which should be mixed thoroughly and used within 24 hours for uniform lustre.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Tuffkote: Epigard Epoxy Finish Heat Resisting Lustrol Aluminium

    Uploaded by

    SHATABDI- DEL
    27 views2 pages
    This document provides information on Heat Resisting Lustrol Aluminium, a two-part aluminum pigment paint with heat resistance up to 250°C. It can be used as a topcoat on chimneys, boilers, ducts, and industrial equipment. The paint has a bright metallic finish when dry and good chemical resistance to acids, alkalis, and solvents when properly coated. It is supplied in kits containing the aluminum paste and medium, which should be mixed thoroughly and used within 24 hours for uniform lustre.

    Original Title

    Untitled

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides information on Heat Resisting Lustrol Aluminium, a two-part aluminum pigment paint with heat resistance up to 250°C. It can be used as a topcoat on chimneys, boilers, ducts, and industrial equipment. The paint has a bright metallic finish when dry and good chemical resistance to acids, alkalis, and solvents when properly coated. It is supplied in kits containing the aluminum paste and medium, which should be mixed thoroughly and used within 24 hours for uniform lustre.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    27 views2 pages

    Tuffkote: Epigard Epoxy Finish Heat Resisting Lustrol Aluminium

    Uploaded by

    SHATABDI- DEL
    This document provides information on Heat Resisting Lustrol Aluminium, a two-part aluminum pigment paint with heat resistance up to 250°C. It can be used as a topcoat on chimneys, boilers, ducts, and industrial equipment. The paint has a bright metallic finish when dry and good chemical resistance to acids, alkalis, and solvents when properly coated. It is supplied in kits containing the aluminum paste and medium, which should be mixed thoroughly and used within 24 hours for uniform lustre.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    TUFFKOTE

    PROTECTIVE COATINGS
    HEAT RESISTINGEPIGARD
    LUSTROLEPOXY FINISH
    ALUMINIUM
    Data Sheet No. 2018 - 005
    Data Sheet No. SPL/PMG/20191000301

    A high lustre two pack oleoresinous aluminium pigment based paint with remarkable protective properties and heat
    resistance upto 250⁰C.

    Product Information Surface Preparation


    Color Aluminium
    Steel Surface
    Surface must be clean, dry & free from
    Finish Bright Metallic
    contamination. Prior to paint application all
    surfaces should be assessed and treated in
    Flash Point Above 30C accordance with ISO 8504:2000.

    Abrasive blast clean to SA 2½ is recommended. If


    Volume Solids 35 ± 2 % Abrasive blast cleaning is not possible it is
    recommended to hand tool/ power tool cleaning
    up St2.
    Recommended dry
    15 - 20 microns
    film thickness
    For damage area rectification please contact the
    Corresponding wet Technical team of Shalimar Paints Limited.
    42 - 60 microns
    film thickness
    Application Details
    Theoretical
    23.33 – 17.5 Sq.m/ltr
    Spreading Rate Method of Application
    Brush / Conventional Spray
    Touch dry 4 – 6 hours
    Drying time Aluminium paste and medium supplied in
    Hand dry 15 – 18 hours
    proportionate quantities. Mix the contents
    thoroughly and stir well before and during
    Interval before Over- Minimum 18 hours application. Mixed paint to be used off within 24
    coating Maximum Indefinite hours to maintain uniformity in lustre.

    VOC 550 gm/ltr (EPA Method 24) Thinner 6751

    12 months minimum @ 30°C if Uses


    stored in dry in sealed container Suitable as topcoat for as a heat resistant coating
    Storage Life
    at shaded condition away from for chimney stacks, boiler fronts, duct work,
    heat source and ignition piping and furnace structure, industrial plants,
    warehouses etc. It has special use in coating
    Dry Heat Resistance Up to 250C (Continuous) exterior of storage tanks in oil and gas industry.

    1
    HEAT RESISTING LUSTROL ALUMINIUM

    Typical System Selection Guide


    SURFACE 1ST COAT 2ND COAT 3RD COAT
    Tuffkote ROZC Primer / Heat Resisting Lustrol Heat Resisting Lustrol
    Steel
    Tuffkote HB ZP Primer Aluminium Aluminium
    Heat Resisting Lustrol Heat Resisting Lustrol
    - Do - -
    Aluminium Aluminium

    Chemical Resistance Guide (with suitable top coat)

    EXPOSURE Acids Alkalis Solvents Salt Water

    SPLASH & SPILLAGE poor poor Fair Fair Fair

    FUMES & OUTDOOR EXPOSURE Good Good Good Good Good

    Health & Safety


    Use Proper Personal Protective Equipment(PPE) during application of this product.

    Please consult Material Safety Datasheet (MSDS)

    Precaution

    Provide adequate ventilation during application and drying. Clean Spray gun equipment and hose immediately
    after application of material.

    Standard Pack Size


    1,4 & 20 litres - For available pack size contact local representative of Shalimar Paints Limited

    NOTES:
    1. This Product datasheet supersedes all previous datasheet and subject to change without prior notice
    2. Do not apply when surface temperature is less than 3C than dew point.
    3. Mixing with mechanical agitator is strongly recommended
    4. Do not apply paints when environment temperature rises above 50C or when relative humidity rises above 85%. Do not
    apply during rain, fog or mist.
    5. Use of thinners other than supplied or approved by Shalimar may adversely affect product performance
    6. Drying is dependent on temperature, relative humidity and thickness; ranges is given for considering those parameters
    7. System Guide is a typical and for indicative purpose only, however this can have wide range of combination. For details,
    please contact Shalimar Paints limited
    8. Request for details information of surface preparation, paint application on the recommended coating system

    DISCLAIMER: This PDS is by no means a comprehensive data. The company will not be liable for losses or damages howsoever caused including liability for
    negligence, which may be suffered by the user of the data contained therein. It is the user's responsibility to conduct all necessary tests to confirm the suitability
    of any product or system for their intended use. No guarantee of result is extended since conditions of use are beyond our control. Liability is limited to
    replacement of the product hence cost of labour charges or consequential damages are excluded.

    Rev 3 - 04/2020 2

    You might also like