Whirlpool Menus PDF

KR38
Technical Education
Troubleshooting Gas and

Electric Freestanding Range
Electronic Controls
KitchenAid
Amana
Maytag
Whirlpool
Prepared by: WHIRLPOOL CONSUMER CARE Job Aid W10378809

FORWARD
This Freestanding Gas and Electric Range Controls Troubleshooting Guide (W10378809), provides the In-
Home Service Professional with information on troubleshooting controls on freestanding gas and electric
ranges. For specific information on the model being serviced, refer to the information supplied with the
range. Always use the Tech Sheet supplied with the product when servicing the range.
GOALS AND OBJECTIVES

The goal of this Job Aid is to provide information that will enable the In-Home Service Professional to
properly diagnose malfunctions of gas and electric freestanding ranges.
The objectives of this Job Aid are to:
• Understand and follow proper safety precautions.
• Successfully troubleshoot and diagnose malfunctions.
• Successfully perform necessary repairs.
• Successfully return the range to its proper operational status.
WHIRLPOOL CORPORATION assumes no responsibility for any repairs made on our products by anyone other
than authorized In-Home Service Professionals.
®Registered trademark of Whirlpool, U.S.A., KitchenAid, U.S.A., Jenn-Air, U.S.A., or Maytag Corporation or its related companies.
®MAGIC CHEF is a registered trademark of CNA International, used under license.
© 2011 All rights reserved.
Table of Contents
Model
Model Control, Range
Control, Description
Range Description Page Tech
Page TechSheet F
Sheet F Codes
Codes
AER5522VAS0 LCC95, Self Clean, Electric 1-11 W10198623 1-26
AER5522VAW0 LCC95, Self Clean, Electric 1-11 W10198623 1-26
AER5522VCS0 LCC95, Self Clean, Electric 1-11 W10198623 1-26
AER5522VCW0 LCC95, Self Clean, Electric 1-11 W10198623 1-26
AER5821VAS0 LCC90, Standard Clean, Electric 1-2 W10133888 1-26
AER5821VAW0 LCC90, Standard Clean, Electric 1-2 W10133888 1-26
AER5822VAB0 LCC180, Standard Clean, Electric 1-3 W10312292 1-26
AER5822VAD0 LCC180, Standard Clean, Electric 1-3 W10312292 1-26
AER5822VAS0 LCC180, Standard Clean, Electric 1-3 W10312292 1-26
AER5822VAW0 LCC180, Standard Clean, Electric 1-3 W10312292 1-26
AER5822VCB0 LCC95, Self Clean, Electric 1-11 W10198623 1-26
AER5822VCB0 LCC180, Standard Clean, Electric 1-3 W10312292 1-26
AER5822VCS0 LCC95, Self Clean, Electric 1-11 W10198623 1-26
AER5822VCS0 LCC180, Standard Clean, Electric 1-3 W10312292 1-26
AER5822VCW0 LCC95, Self Clean, Electric 1-11 W10198623 1-26
AER5822VCW0 LCC180, Standard Clean, Electric 1-3 W10312292 1-26
AER5823XAB0 LCC180, Standard Clean, Electric 1-3 W10312292 1-26
AER5823XAS0 LCC180, Standard Clean, Electric 1-3 W10312292 1-26
AER5823XAW0 LCC180, Standard Clean, Electric 1-3 W10312292 1-26
AER5830VAB0 LCC180, Self Clean, Electric 1-11 W10198626 1-26
AER5830VAD0 LCC180, Self Clean, Electric 1-11 W10198626 1-26
AER5844VAB0 LCC180, Self Clean, Electric 1-11 W10198626 1-26
AER5844VAD0 LCC180, Self Clean, Electric 1-11 W10198626 1-26
AER6011VAB0 LCC190, Self-Clean, Convection, Electric 1-21 W10198627 1-26
AER6011VAS0 LCC190, Self-Clean, Convection, Electric 1-21 W10198627 1-26
AER6011VAW0 LCC190, Self-Clean, Convection, Electric 1-21 W10198627 1-26
AGR4422VDB0 EZ175, Standard Clean, Gas 1-6 W10155514 1-26
AGR4422VDD0 EZ175, Standard Clean, Gas 1-6 W10155514 1-26
AGR4422VDS0 EZ175, Standard Clean, Gas 1-6 W10155514 1-26
AGR4422VDW0 EZ175, Standard Clean, Gas 1-6 W10155514 1-26
AGR4433XDB0 LCC90, Standard Clean, Gas 1-8 W10142327 1-26
AGR4433XDS0 LCC90, Standard Clean, Gas 1-8 W10142327 1-26
AGR4433XDW0 LCC90, Standard Clean, Gas 1-8 W10142327 1-26
AGR5844VDB0 LCC95, Self Clean, Gas 1-15 W10198635 1-26
AGR5844VDD0 LCC95, Self Clean, Gas 1-15 W10198635 1-26
AGR5844VDS0 LCC95, Self Clean, Gas 1-15 W10198635 1-26
AGR5844VDW0 LCC95, Self Clean, Gas 1-15 W10198635 1-26
AGR6011VDB0 LCC190, Self-Clean, Convection, Gas 1-24 W10198636 1-26
AGR6011VDB1 LCC190, Self-Clean, Convection, Gas 1-24 W10198636 1-26
AGR6011VDS0 LCC190, Self-Clean, Convection, Gas 1-24 W10198636 1-26
AGR6011VDS1 LCC190, Self-Clean, Convection, Gas 1-24 W10198636 1-26
AGR6011VDW0 LCC190, Self-Clean, Convection, Gas 1-24 W10198636 1-26
AGR6011VDW1 LCC190, Self-Clean, Convection, Gas 1-24 W10198636 1-26
i
Table of Contents
Model Control, Range Description Page Tech Sheet F Codes
GFE461LVB0 MRC, True Convection, Electric, 2-2 W10198585 2-10
GFE461LVQ0 MRC, True Convection, Electric, 2-2 W10198585 2-10
GFE461LVS0 MRC, True Convection, Electric, 2-2 W10198585 2-10
GFE461LVT0 MRC, True Convection, Electric, 2-2 W10198585 2-10
GFE471LVB0 MRC, True Convection, Warming Drawer, Electric, 2-2 W10198586 2-10
GFE471LVQ0 MRC, True Convection, Warming Drawer, Electric, 2-2 W10198586 2-10
GFE471LVS0 MRC, True Convection, Warming Drawer, Electric, 2-2 W10198586 2-10
GFG461LVB0 MRC, Fan Convection, Gas 2-6 W10198620 2-10
GFG461LVQ0 MRC, Fan Convection, Gas 2-6 W10198620 2-10
GFG461LVS0 MRC, Fan Convection, Gas 2-6 W10198620 2-10
GFG461LVT0 MRC, Fan Convection, Gas 2-6 W10198620 2-10
GFG471LVB0 MRC, Fan Convection, Warming Drawer, Gas 2-6 W10208861 2-10
GFG471LVB1 MRC, Fan Convection, Warming Drawer, Gas 2-6 W10208861 2-10
GFG471LVQ0 MRC, Fan Convection, Warming Drawer, Gas 2-6 W10208861 2-10
GFG471LVQ1 MRC, Fan Convection, Warming Drawer, Gas 2-6 W10208861 2-10
GFG471LVS0 MRC, Fan Convection, Warming Drawer, Gas 2-6 W10208861 2-10
GFG471LVS1 MRC, Fan Convection, Warming Drawer, Gas 2-6 W10208861 2-10
GGE388LXB00 MRC II, Dble Oven, Warming Zone, Electric, 3-2 W10311742 3-16
GGE388LXQ00 MRC II, Dble Oven, Warming Zone, Electric, 3-2 W10311742 3-16
GGE388LXS00 MRC II, Dble Oven, Warming Zone, Electric, 3-2 W10311742 3-16
GGE390LXB00 MRC II, Dble Oven, True Convect, Warm Zone, Electric, 3-2 W10311744 3-16
GGE390LXQ00 MRC II, Dble Oven, True Convect, Warm Zone, Electric, 3-2 W10311744 3-16
GGE390LXS00 MRC II, Dble Oven, True Convect, Warm Zone, Electric, 3-2 W10311744 3-16
GGG388LXB00 MRC II, Double Oven, Gas 3-8 W10311748 3-16
GGG388LXQ00 MRC II, Double Oven, Gas 3-8 W10311748 3-16
GGG388LXS00 MRC II, Double Oven, Gas 3-8 W10311748 3-16
GGG390LXB00 MRC II, Double Oven, True Convection Lower, Gas 3-10 W10311749 3-16
GGG390LXQ00 MRC II, Double Oven, True Convection Lower, Gas 3-10 W10311749 3-16
GGG390LXS00 MRC II, Double Oven, True Convection Lower, Gas 3-10 W10311749 3-16
IVE32300 LCC90, Standard Clean, Electric 1-2 W10251245 1-26
IVE82300 LCC90, Standard Clean, Electric 1-2 W10251245 1-26
IVP33800 LCC95, Self Clean, Electric 1-10 W10221843 1-26
KDRS505XSS00 MRC II, Dble Oven, True Convect Lower Oven, Dual Fuel 3-6 W10323649 3-16
KERS505XBL00 MRC II, Dble Oven, True Convect Lower, Warm Zone, Electric 3-5 W10311747 3-16
KERS505XSS00 MRC II, Dble Oven, True Convect Lower, Warm Zone, Electric 3-5 W10311747 3-16
KERS505XWH00 MRC II, Dble Oven, True Convect Lower, Warm Zone, Electric 3-5 W10311747 3-16
KERS507XSS00 MRC II, Dble Oven, True Convect Lower, Warm Zone, Electric 3-5 W10323648 3-16
KGRS505XBL00 MRC II, Dble Oven, True Convect Lower Oven, Gas 3-14 W10311752 3-16
KGRS505XSS00 MRC II, Dble Oven, True Convect Lower Oven, Gas 3-14 W10311752 3-16
KGRS505XWH00 MRC II, Dble Oven, True Convect Lower Oven, Gas 3-14 W10311752 3-16
ii
Table of Contents
MER7662WB0 LCC95, Self Clean, Electric 1-11 W10237513 1-26
MER7662WB1 LCC95, Self Clean, Electric 1-11 W10237513 1-26
MER7662WQ1 LCC95, Self Clean, Electric 1-11 W10237513 1-26
MER7662WS0 LCC95, Self Clean, Electric 1-11 W10237513 1-26
MER7662WS1 LCC95, Self Clean, Electric 1-11 W10237513 1-26
MER7662WT0 LCC95, Self Clean, Electric 1-11 W10237513 1-26
MER7662WW0 LCC95, Self Clean, Electric 1-11 W10237513 1-26
MER7662WW1 LCC95, Self Clean, Electric 1-11 W10237513 1-26
MER7765WB0 LCC190, Self Clean, Convection, Electric 1-20 W10237514 1-26
MER7765WS0 LCC190, Self Clean, Convection, Electric 1-20 W10237514 1-26
MER7765WW0 LCC190, Self Clean, Convection, Electric 1-20 W10237514 1-26
MER7775WB0 LCC190, Self Clean, Convection, Steam, Electric 1-20 W10237514 1-26
MER7775WB1 LCC190, Self Clean, Convection, Steam, Electric 1-20 W10237514 1-26
MER7775WS0 LCC190, Self Clean, Convection, Steam, Electric 1-20 W10237514 1-26
MER7775WS1 LCC190, Self Clean, Convection, Steam, Electric 1-20 W10237514 1-26
MER7775WW0 LCC190, Self Clean, Convection, Steam, Electric 1-20 W10237514 1-26
MER7775WW1 LCC190, Self Clean, Convection, Steam, Electric 1-20 W10237514 1-26
MER8770WQ0 LCC190, Self Clean, Convection, Electric 1-21 W10249695 1-26
MER8772WB0 MRC, Fan Convection, Electric, 2-3 W10239462 2-10
MER8772WB1 MRC, Fan Convection, Electric, 2-3 W10239462 2-10
MER8772WS0 MRC, Fan Convection, Electric, 2-3 W10239462 2-10
MER8772WS1 MRC, Fan Convection, Electric, 2-3 W10239462 2-10
MER8772WW0 MRC, Fan Convection, Electric, 2-3 W10239462 2-10
MER8772WW1 MRC, Fan Convection, Electric, 2-3 W10239462 2-10
MER8875WB0 MRC, True Convection, Electric 2-3 W10239465 2-10
MER8875WB1 MRC, True Convection, Electric 2-3 W10239465 2-10
MER8875WS0 MRC, True Convection, Electric 2-3 W10239465 2-10
MER8875WS1 MRC, True Convection, Electric 2-3 W10239465 2-10
MER8875WW0 MRC, True Convection, Electric 2-3 W10239465 2-10
MER8875WW1 MRC, True Convection, Electric 2-3 W10239465 2-10
MET8665XB00 MRC II, Double Oven, Electric 3-2 W10311745 3-16
MET8665XS00 MRC II, Double Oven, Electric 3-2 W10311745 3-16
MET8665XW00 MRC II, Double Oven, Electric 3-2 W10311745 3-16
MET8775XB00 MRC II, Dble Oven, Fan Convect Lower, Warm Zone, Electric 3-3 W10311746 3-16
MET8775XS00 MRC II, Dble Oven, Fan Convect Lower, Warm Zone, Electric 3-3 W10311746 3-16
MET8775XW00 MRC II, Dble Oven, Fan Convect Lower, Warm Zone, Electric 3-3 W10311746 3-16
MET8885XB00 MRC II, Dble Oven, True Convect Lower, Warm Zone, Electric 3-3 W10311747 3-16
MET8885XS00 MRC II, Dble Oven, True Convect Lower, Warm Zone, Electric 3-3 W10311747 3-16
MET8885XW00 MRC II, Dble Oven, True Convect Lower, Warm Zone, Electric 3-3 W10311747 3-16
MGR7661WB0 LCC95, Self Clean, Gas 1-14 W10198635 1-26
MGR7661WS0 LCC95, Self Clean, Gas 1-14 W10198635 1-26
MGR7661WW0 LCC95, Self Clean, Gas 1-14 W10198635 1-26
MGR7662WQ0 LCC190, Self Clean, Gas 1-15 W10198615 1-26
iii
Table of Contents
MGR7775WB0 LCC190, Self Clean, Convection, Gas 1-24 W10198636 1-26
MGR7775WB1 LCC190, Self Clean, Convection, Gas 1-24 W10198636 1-26
MGR7775WS0 LCC190, Self Clean, Convection, Gas 1-24 W10198636 1-26
MGR7775WS1 LCC190, Self Clean, Convection, Gas 1-24 W10198636 1-26
MGR7775WW0 LCC190, Self Clean, Convection, Gas 1-24 W10198636 1-26
MGR7775WW1 LCC190, Self Clean, Convection, Gas 1-24 W10198636 1-26
MGR8772WB0 MRC, Fan Convection, Gas 2-8 W10239474 2-10
MGR8772WS0 MRC, Fan Convection, Gas 2-8 W10239474 2-10
MGR8772WW0 MRC, Fan Convection, Gas 2-8 W10239474 2-10
MGT8655XB00 MRC II, Double Oven, Fan Convection Lower Oven, Gas 3-10 W10311748 3-16
MGT8655XS00 MRC II, Double Oven, Fan Convection Lower Oven, Gas 3-10 W10311748 3-16
MGT8655XW00 MRC II, Double Oven, Fan Convection Lower Oven, Gas 3-10 W10311748 3-16
MGT8775XB00 MRC II, Double Oven, Fan Convection Lower Oven, Gas 3-10 W10311749 3-16
MGT8775XS00 MRC II, Double Oven, Fan Convection Lower Oven, Gas 3-10 W10311749 3-16
MGT8775XW00 MRC II, Double Oven, Fan Convection Lower Oven, Gas 3-10 W10311749 3-16
MGT8885XB00 MRC II, Double Oven, True Convection Lower Oven, Gas 3-11 W10311752 3-16
MGT8885XS00 MRC II, Double Oven, True Convection Lower Oven, Gas 3-11 W10311752 3-16
MGT8885XW00 MRC II, Double Oven, True Convection Lower Oven, Gas 3-11 W10311752 3-16
SF114PXSB2 LCC90, Standard Clean, GAS 1-8 W10200950 1-26
SF114PXSQ2 LCC90, Standard Clean, GAS 1-8 W10200950 1-26
SF114PXST2 LCC90, Standard Clean, GAS 1-8 W10200950 1-26
SF114PXSW2 LCC90, Standard Clean, GAS 1-8 W10200950 1-26
TES325VQ0 LCC95, Self Clean, Electric 1-10 W10221843 1-26
TES325VT0 LCC95, Self Clean, Electric 1-10 W10221843 1-26
TGS325VB0 LCC95, Self Clean, GAS 1-14 W10198635 1-26
TGS325VB1 LCC95, Self Clean, GAS 1-14 W10198635 1-26
TGS325VQ0 LCC95, Self Clean, GAS 1-14 W10198635 1-26
TGS325VQ1 LCC95, Self Clean, GAS 1-14 W10198635 1-26
TGS325VT0 LCC95, Self Clean, GAS 1-14 W10198635 1-26
TGS325VT1 LCC95, Self Clean, GAS 1-14 W10198635 1-26
WFE114LWS0 LCC90, Standard Clean, Electric 1-2 W10251245 1-26
WFE301LVB0 LCC90, Standard Clean, Electric 1-2 W10251245 1-26
WFE301LVQ0 LCC90, Standard Clean, Electric 1-2 W10251245 1-26
iv
Table of Contents
WFE301LVS0 LCC90, Standard Clean, Electric 1-2 W10251245 1-26
WFE321LWB0 LCC90, Standard Clean, Steam,Electric 1-2 W10267424 1-26
WFE321LWQ0 LCC90, Standard Clean, Steam,Electric 1-2 W10267424 1-26
WFE321LWS0 LCC90, Standard Clean, Steam,Electric 1-2 W10267424 1-26
WFE324LWB0 LCC90, Standard Clean, Steam,Electric 1-2 W10267424 1-26
WFE324LWQ0 LCC90, Standard Clean, Steam,Electric 1-2 W10267424 1-26
WFE324LWS0 LCC90, Standard Clean, Steam,Electric 1-2 W10267424 1-26
WFE361LVB0 LCC95, Self Clean, Electric 1-10 W10221843 1-26
WFE361LVD0 LCC95, Self Clean, Electric 1-10 W10221843 1-26
WFE361LVQ0 LCC95, Self Clean, Electric 1-10 W10221843 1-26
WFE361LVS0 LCC95, Self Clean, Electric 1-10 W10221843 1-26
WFE361LVT0 LCC95, Self Clean, Electric 1-10 W10221843 1-26
WFE364LVB0 LCC190, Self-Clean, Electric 1-10 W10198581 1-26
WFE364LVD0 LCC190, Self-Clean, Electric 1-10 W10198581 1-26
WFE364LVQ0 LCC190, Self-Clean, Electric 1-10 W10198581 1-26
WFE364LVS0 LCC190, Self-Clean, Electric 1-10 W10198581 1-26
WFE364LVT0 LCC190, Self-Clean, Electric 1-10 W10198581 1-26
WFE366LVB0 LCC190, Self-Clean, Electric 1-10 W10198581 1-26
WFE366LVQ0 LCC190, Self-Clean, Electric 1-10 W10198581 1-26
WFE366LVS0 LCC190, Self-Clean, Electric 1-10 W10198581 1-26
WFE366LVT0 LCC190, Self-Clean, Electric 1-10 W10198581 1-26
WFE371LVB0 LCC190, Self Clean, Steam, Electric 1-10 W10198582 1-26
WFE371LVQ0 LCC190, Self Clean, Steam, Electric 1-10 W10198582 1-26
WFE371LVS0 LCC190, Self Clean, Steam, Electric 1-10 W10198582 1-26
WFE371LVT0 LCC190, Self Clean, Steam, Electric 1-10 W10198582 1-26
WFE374LVB0 LCC190, Self Clean, Steam, Electric 1-10 W10198582 1-26
WFE374LVQ0 LCC190, Self Clean, Steam, Electric 1-10 W10198582 1-26
WFE374LVS0 LCC190, Self Clean, Steam, Electric 1-10 W10198582 1-26
WFE374LVT0 LCC190, Self Clean, Steam, Electric 1-10 W10198582 1-26
WFE381LVB0 LCC190, Self Clean, Convection, Steam, Electric 1-20 W10198584 1-26
WFE381LVQ0 LCC190, Self Clean, Convection, Steam, Electric 1-20 W10198584 1-26
WFE381LVS0 LCC190, Self Clean, Convection, Steam, Electric 1-20 W10198584 1-26
WFG114SVB0 LCC90, Standard Clean, GAS 1-8 W10200950 1-26
WFG114SVQ0 LCC90, Standard Clean, GAS 1-8 W10200950 1-26
WFG114SVT0 LCC90, Standard Clean, GAS 1-8 W10200950 1-26
WFG114SVW0 LCC90, Standard Clean, GAS 1-8 W10200950 1-26
WFG231LVB0 LCC90, Standard Clean, GAS 1-8 W10200950 1-26
WFG231LVQ0 LCC90, Standard Clean, GAS 1-8 W10200950 1-26
WFG231LVS0 LCC90, Standard Clean, GAS 1-8 W10200950 1-26
WFG361LVB0 LCC190, Self Clean, GAS 1-14 W10198618 1-26
WFG361LVD0 LCC190, Self Clean, GAS 1-14 W10198618 1-26
WFG361LVQ0 LCC190, Self Clean, GAS 1-14 W10198618 1-26
WFG361LVS0 LCC190, Self Clean, GAS 1-14 W10198618 1-26
WFG361LVT0 LCC190, Self Clean, GAS 1-14 W10198618 1-26
WFG361LVT1 LCC190, Self Clean, GAS 1-14 W10198618 1-26
v
Table of Contents
YGFE461LVB0 MRC, True Convection, Electric, 2-2 W10198585 2-10
YGFE461LVQ0 MRC, True Convection, Electric, 2-2 W10198585 2-10
YGFE461LVS0 MRC, True Convection, Electric, 2-2 W10198585 2-10
YGFE471LVB0 MRC, True Convection, Warming Drawer, Electric, 2-2 W10198586 2-10
YGFE471LVQ0 MRC, True Convection, Warming Drawer, Electric, 2-2 W10198586 2-10
YGFE471LVS0 MRC, True Convection, Warming Drawer, Electric, 2-2 W10198586 2-10
YKER507XSS00 MRC II, Dble Oven, True Convect Lower, Warm Zone, Electric 3-5 W10323648 3-16
YMER7662WB0 LCC95, Self Clean, Electric 1-11 W10237513 1-26
YMER7662WB1 LCC95, Self Clean, Electric 1-11 W10237513 1-26
YMER7662WS1 LCC95, Self Clean, Electric 1-11 W10237513 1-26
YMER7662WW0 LCC95, Self Clean, Electric 1-11 W10237513 1-26
YMER7662WW1 LCC95, Self Clean, Electric 1-11 W10237513 1-26
YMER7765WB0 LCC190, Self Clean, Convection, Electric 1-20 W10237514 1-26
YMER7765WB1 LCC190, Self Clean, Convection, Electric 1-20 W10237514 1-26
YMER7765WS0 LCC190, Self Clean, Convection, Electric 1-20 W10237514 1-26
YMER7765WS1 LCC190, Self Clean, Convection, Electric 1-20 W10237514 1-26
YMER7765WW0 LCC190, Self Clean, Convection, Electric 1-20 W10237514 1-26
YMER7765WW1 LCC190, Self Clean, Convection, Electric 1-20 W10237514 1-26
YMER8772WB0 MRC, Fan Convection, Electric, 2-3 W10239462 2-10
YMER8772WB1 MRC, Fan Convection, Electric, 2-3 W10239462 2-10
YMER8772WS0 MRC, Fan Convection, Electric, 2-3 W10239462 2-10
YMER8772WS1 MRC, Fan Convection, Electric, 2-3 W10239462 2-10
YMER8772WW0 MRC, Fan Convection, Electric, 2-3 W10239462 2-10
YMER8772WW1 MRC, Fan Convection, Electric, 2-3 W10239462 2-10
YMER8875WB0 MRC, True Convection, Electric 2-3 W10239465 2-10
YMER8875WB1 MRC, True Convection, Electric 2-3 W10239465 2-10
YMER8875WS0 MRC, True Convection, Electric 2-3 W10239465 2-10
YMER8875WS1 MRC, True Convection, Electric 2-3 W10239465 2-10
YMER8875WW0 MRC, True Convection, Electric 2-3 W10239465 2-10
YMER8875WW1 MRC, True Convection, Electric 2-3 W10239465 2-10
YMERH770WB0 LCC190, Self Clean, Convection, Electric 1-21 W10249695 1-26
YMERH770WB0 MRC, Fan Convection, Electric, 2-3 W10239462 2-10
YMERH770WB1 LCC190, Self Clean, Convection, Electric 1-21 W10249695 1-26
YMERH770WB1 MRC, Fan Convection, Electric, 2-3 W10239462 2-10
YMERH770WS0 LCC190, Self Clean, Convection, Electric 1-21 W10249695 1-26
YMERH770WS0 MRC, Fan Convection, Electric, 2-3 W10239462 2-10
YMERH770WS1 LCC190, Self Clean, Convection, Electric 1-21 W10249695 1-26
YMERH770WS1 MRC, Fan Convection, Electric, 2-3 W10239462 2-10
YMERH770WW0 LCC190, Self Clean, Convection, Electric 1-21 W10249695 1-26
YMERH770WW0 MRC, Fan Convection, Electric, 2-3 W10239462 2-10
YMERH770WW1 LCC190, Self Clean, Convection, Electric 1-21 W10249695 1-26
vi
Table of Contents
YMERH770WW1 MRC, Fan Convection, Electric, 2-3 W10239462 2-10
YMET8665XB00 MRC II, Double Oven, Electric 3-2 W10311745 3-16
YMET8665XS00 MRC II, Double Oven, Electric 3-2 W10311745 3-16
YMET8665XW00 MRC II, Double Oven, Electric 3-2 W10311745 3-16
YMET8885XB00 MRC II, Dble Oven, True Convect Lower, Warm Zone, Electric 3-3 W10311747 3-16
YMET8885XS00 MRC II, Dble Oven, True Convect Lower, Warm Zone, Electric 3-3 W10311747 3-16
YMET8885XW00 MRC II, Dble Oven, True Convect Lower, Warm Zone, Electric 3-3 W10311747 3-16
YRF115LXVB0 LCC90, Standard Clean, Electric 1-2 W10251245 1-26
YRF115LXVQ0 LCC90, Standard Clean, Electric 1-2 W10251245 1-26
YRF115LXVS0 LCC90, Standard Clean, Electric 1-2 W10251245 1-26
YWFE301LVB0 LCC90, Standard Clean, Electric 1-2 W10251245 1-26
YWFE301LVQ0 LCC90, Standard Clean, Electric 1-2 W10251245 1-26
YWFE301LVS0 LCC90, Standard Clean, Electric 1-2 W10251245 1-26
YWFE361LVB0 LCC95, Self Clean, Electric 1-10 W10221843 1-26
YWFE361LVQ0 LCC95, Self Clean, Electric 1-10 W10221843 1-26
YWFE361LVS0 LCC95, Self Clean, Electric 1-10 W10221843 1-26
YWFE366LVB0 LCC190, Self Clean, Electric 1-10 W10198581 1-26
YWFE366LVQ0 LCC190, Self Clean, Electric 1-10 W10198581 1-26
YWFE366LVS0 LCC190, Self Clean, Electric 1-10 W10198581 1-26
YWFE371LVB0 LCC190, Self Clean, Steam, Electric 1-10 W10198582 1-26
YWFE371LVQ0 LCC190, Self Clean, Steam, Electric 1-10 W10198582 1-26
YWFE371LVS0 LCC190, Self Clean, Steam, Electric 1-10 W10198582 1-26
YWFE381LVB0 LCC190, Self Clean, Convection, Steam, Electric 1-20 W10198584 1-26
YWFE381LVQ0 LCC190, Self Clean, Convection, Steam, Electric 1-20 W10198584 1-26
YWFE381LVS0 LCC190, Self Clean, Convection, Steam, Electric 1-20 W10198584 1-26
vii
NOTES
1-1
LCC Standard Clean, Electric
LCC90 Control, Standard Clean, Electric

Models:
WFE114LWS0
WFE301LVB0
WFE301LVQ0
WFE301LVS0
YRF115LXVB0
YRF115LXVQ0
YRF115LXVS0
YWFE301LVB0
YWFE301LVQ0
YWFE301LVS0
IVE32300
IVE82300
LCC190 Control, Standard Clean, Steam Clean, Electric

Models:
WFE321LWB0
WFE321LWQ0
WFE321LWS0
WFE324LWB0
WFE324LWQ0
WFE324LWS0
Reviewed by Genview Automated Process | Released

Models:
AER5821VAS0
AER5821VAW0
1- 2
eviewed by Staples, Debra L. | Released
LCC Standard Clean, Electric (continued)
Models:
AER5822VAB0
AER5822VAD0
AER5822VAS0
AER5822VAW0
AER5822VCB0
AER5822VCS0
AER5822VCW0
AER5823XAB0
AER5823XAS0
AER5823XAW0
Temperature Adjustment
1. Press BAKE for 5 seconds. Previous Offset shown, or U-00 is displayed.
bra L. | Released
Adjusts temperature in 10⁰ F (5⁰ C) increments
2. Press TEMP/TIME "+" or "-".
TEMP/HOUR between -30⁰F and +30⁰F.
Bake and Broil Temperatures are offset
automatically to the same degree.
3. Press START.
If START is not pressed within 1 minute, adjustment
is ignored.
Diagnostic Mode
Action Display
1. Press CANCEL/CANCEL/START "tSt" (You are in the test mode)
2. Press the TEMP/HOUR
TEMP/TIME "+" key ###⁰F or ⁰C (Oven Sensor Temperature)
Press "+" again -30⁰F to +30⁰F (Oven Offset Temperature)
"+" again ### (Control Software Version)
"+" again ### (Control Memory Checksum)
"CLr" (Good Control)
"+" again will display 1 of the 3 F# *(Error Code - See Tech Sheet for Repair) ##
## of operation
(Hours (Hours of
at operation
error code)at error code)
"+" again #### (Total hours of oven operation)
"+" again "00" (Door Open) or "01" (Door Closed)
*Press *Press
“START"START"
TIME” to clear all fault codes
When checking for fault codes, if the display shows "CLr", Do Not replace the control.
1-3
FOR SERVICE TECHNICIAN’S USE ONLY
Wiring
Wiring Diagram
Information TS W10267424
NOTE: Schematic shows door latch switch in the COOK position with oven door open and elements off.
L1
Oven Control LCC190 L2
Door Position Switch
BK CON 3-3
Y Y R
N
CON 3-4 W
Y Oven Temp Sensor
CON 3-9
V
CON 3-10
Oven Light (K2) CON 1-5 V W
BK/W Oven Light Assy 40W
Power Supply CON 1-1 W
W
CON 2-4
BK Bake 2400W
Bake (K4) CON 2-7 R
Broil (K3) CON 2-1 R R Broil 3400W R BU/W Thermo Fuse R
DLB (K5) CON 4 BU
CON 4 R
R Hot Surface
Indicator
2b 1b Light
BK FOR SERVICE TECHNICIAN’S USE ONLY
On some
PKBK
models OR OR OR W
L1 H1 1a 3000W 2a H2 LF L2
BK P
OR/BK Quick Connect Plugs
Left Front Element
OR R
LFFor controls
V BK Connectors For cooktop
2b 1b
Y
L1 H1 1a 1200W 2a H2 LR L2
BK
CON3 CON1
P
Y/BK
CON2
Left Rear Element Y BK R
LR V
2b 1b BK OR
H1W BU
BK L1 BK BU BU BU
1a 1800W 2a H2 RR L2
BU
BK P BU/BK Right Rear Element BU R
RR V BK
Y 2b 1b
BR
Right Side Left Side
L1 H1 1a 1200W 2a CooktopH2 CooktopRF L2
BKY P
BR/BK BKRight Front Element BR R
RF V
BK/W Cooktop On
Infinite Switches IND Light
(Cycles ON/OFF When Hot)
V W GND
(On When Any Burner
R Is Turned On)
V LEGEND
V
CON1-2 = Connector 1 Multiple
CON1 Position 2 Functions / Circuitry
Component Connection No On Some In Line Enclosed Within
Terminals (Splice) Connection Models Connection
PIN 1
PIN 1
CON 1
CON 3
PIN 1
PIN 1
CON 2
CON 4
1- 4
Conn Pin Function
NOTES
1-5
EZ Control, Standard Clean, Gas
Models:
AGR4422VDB0
AGR4422VDD0
AGR4422VDS0
AGR4422VDW0
Press BAKE for 5 seconds. Previous Offset shown, or U-00 is displayed.
ew Automated Process | Released
Press TEMP/TIME of Adjusts temperature in 10⁰ F (5⁰ C) increments
TEMP/HOUR "+" or "-" between -30⁰F and +30⁰F.
Press START
If START is not pressed within 1 minute,
adjustment is ignored.
No Diagnostic Mode Available for this Model
STRIP CIR
1- 6
NOTES:
Replace all parts and panels before operating.
Caution: Label all wires prior to d
Failure to do so can result in death or
servicing controls. Wiring errors c
electrical shock. Wiring Information dangerous operation. TS# W10155514
Verify
NOTE: Schematic shows door latch switch in the COOK position with oven door open proper
and elements off. operation after servi
GROUND OVEN
LIGHT
L1 N
BK ROCKER
SWITCH W
BK Y
COOKTOP TO
MAINBACK OVEN CONTROL
BK P6-1 P6-3 W
TRANSFORMER
V
P1-4
OVEN
TEMP
SENSOR V
P1-5
BK P2-1 P2-4 R R W
BAKE VALVE
BAKE RELAY
BAKE IGNITOR
SURFACE BURNER
IGNITION SWITCHES SPARK MODULE
BK BK R R W
G
OPTIONAL
RCUITS
1-7
LCC Standard Clean, GAS
LCC90 Control, Standard Clean, GAS
Models:
SF114PXSB2
SF114PXSQ2
SF114PXST2
SF114PXSW2
WFG114SVB0
WFG114SVQ0
WFG114SVT0
WFG114SVW0
WFG231LVB0
WFG231LVQ0
WFG231LVS0
LCC90 Control, Standard Clean, GAS
Models:
AGR4433XDB0
AGR4433XDS0
AGR4433XDW0
2. Press TEMP/TIME "+"Temperature Adjustment
or "-".
Reviewed by Staples, Debra L. | Released
1. Press BAKE for 5 seconds. between -30⁰F and +30⁰F.
Previous Offset shown, or U-00 is displayed.
Adjusts temperature
automatically in 10⁰degree.
to the same F (5⁰ C) increments
2. Press TEMP/HOUR
TEMP/TIME "+" or "-".
3. Press START. between -30⁰F and +30⁰F.
If START
Bake andisBroil
not pressed within are
Temperatures 1 minute,
offset adjustment
is ignored.
3. Press START.
ra L. | Released
is ignored.
Diagnostic Mode
Action Display
1. Press CANCEL/CANCEL/START Diagnostic
"tSt" Mode (You are in the test mode)
2. Press the TEMP/HOUR
TEMP/TIME "+" key ###⁰F or ⁰C (Oven Sensor Temperature)
Action
Press "+" again -30⁰F to +30⁰F
Display
(Oven Offset Temperature)
2. Press the TEMP/TIME "+" key ###⁰F or ⁰C (Oven Sensor Temperature)
"+"display
"+" again will again 1 of the 3 ### (Control Software Version)
F# *(Error Code - See Tech Sheet for Repair) ##
"+" again ###
## (Hours of (Control
atMemory Checksum)
(Hours of operation atoperation
error code) error code)
(Hours of operation at error code)
*Press "START" to clear all fault codes
1- 8
Wiring Diagrams
Wiring Information TS# operation.

Caution: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous
Verify proper operation after servicing.
W10200950
NOTE: Schematic shows doors closed and relays off
L1 GND N
BK Failure/Error Display Codes W
DISPLAY LIKELY FAILURE CONDITION SUGGESTED CORRECTIVE ACTION PROCEDURE

CODES
CLr No error(s) found (Good) No corrective action required
G 1. Verify failure, if not displayed. Go to the diagnostics screen and clear the error code by
pressing the START key.
OVEN CONTROL LCC90
OVEN LIGHT
2. Unplug range or disconnect power longer than 30 seconds.
Control failure 3. Plug
OVEN LIGHT RELAY (K-2)in range or reconnect power.
COOKTOP TO
F1 UL A/D Error(s)
MAINBACK 4. Observe for longer than 1 minute.
BAKE/BROIL range over temperature 5. If failure remains, go to Step 6.
6. Unplug range BK
CON1-5 or disconnect power. W
BK CON 2-4 7. Replace control.
8. Replace all parts and panels before operating.
9. Plug in range orY reconnect power.
10. VerifyCON 3-3
operation is normal. Go to Step 1 and complete checks.
1. Verify failure, if not displayed. Go to the diagnostics screen and clear the error code by
pressing Y
the START key.
CON 3-4
V 2. Unplug range or disconnect power longer than 30 seconds.
CON 3-9
3. Plug in range or reconnect power.
OVEN TEMP
F2 SENSOR Shorted key 4. Observe for longer than 1 minute.
5. If failure
POWER remains,
CON 1-1 W go to Step 6. W
V
CON 3-10 6. Unplug range or disconnect power.
SUPPLY
7. Replace control.
10. Verify operation is normal. Go to Step 1 and complete checks.
BAKE AND 1.
BROILUnplug range or disconnect power.
RELAY (K-6)
2.
Disconnect sensor from harness.
3.
Measure sensor value (between connector pins) between 1000Ω @ 32°F (0°C) and
2697ΩCON@2-1
900°F
R (482.2°C) (room temperature
R approximately = 1080Ω) . Also measure
W
from sensor connector to sensor casing for possible short. If measurement does not
correlate to real temperature, or if short is found, replace
BAKE VALVE sensor.
4. Trace wires and connectors to sensor from control, then back to control. If wire or
connection is damaged, replace the harness.
F3 Oven sensor opened 5. Reconnect the sensor to the BAKE IGNITER
harness.
Oven sensor shorted 6. Replace all parts and panels before operating.
SURFACE BURNER
8. Press BAKE and START. Observe for longer than 1 minute. If failure remains,
IGNITION SWITCHES
go to Step 9. SPARK MODULE
BK BK 9. Unplug
R rangeR or disconnect power. W
10. Replace control.
Connectors
12. Plug in range or reconnect power. GND
OPTIONAL
13. Verify operation is normal. Go to Step 1 and complete checks.
Quick Connect Plugs

CON 1 CON 2
W BK R BK
1 1
LEGEND
CON 3
Y Y V V ON
1
COMPONENT CONNECTION NO SOME IN LINE
TERMINAL (SPLICE) CONNECTION MODELS CONNECTION
1-9
3
LCC Self-Clean, Electric
LCC95 Control, Self-Clean, Electric
Models:
WFE361LVB0
WFE361LVD0
WFE361LVQ0
WFE361LVS0
WFE361LVT0
YWFE361LVB0
YWFE361LVQ0
YWFE361LVS0
IVP33800
IVP85800
IVP85801
TES325VQ0
TES325VT0

Models:
WFE364LVB0
WFE364LVD0
WFE364LVQ0
WFE364LVS0
WFE364LVT0
WFE366LVB0
WFE366LVQ0
WFE366LVS0
WFE366LVT0
YWFE366LVB0
YWFE366LVQ0
YWFE366LVS0
LCC190 Control, Self-Clean, Steam Clean, Electric

Reviewed by Genview Automated Process | Released Models:
WFE371LVB0
WFE371LVQ0
WFE371LVS0
WFE371LVT0
WFE374LVB0
WFE374LVQ0
WFE374LVS0
WFE374LVT0
YWFE371LVB0
YWFE371LVQ0
YWFE371LVS0
1- 10
Staples, Debra L. | Released
LCC Self-Clean, Electric (continued)
Models:
MER7662WB0
MER7662WB1
MER7662WQ1
MER7662WS0
MER7662WS1
MER7662WT0
MER7662WW0
MER7662WW1
YMER7662WB0
YMER7662WB1
YMER7662WS1
YMER7662WW0
YMER7662WW1
LCC95 6 Self-Clean, Electric

Models:
AER5522VAS0
AER5522VAW0
AER5522VCS0
AER5522VCW0
AER5822VCB0
AER5822VCS0
AER5822VCW0

Models:
AER5830VAB0
AER5830VAD0
a L. | Released AER5830VAS0
AER5830VAW0
AER5844VAB0
AER5844VAD0
AER5844VAS0
AER5844VAW0
1-11
LCC Self-Clean, Electric (continued)
between -30⁰F and +30⁰F.
3. Press START.
is ignored.
Diagnostic Mode
Action Display
1. Press CANCEL/CANCEL/START "tSt" or “tESt” (You are in the test mode)
2. Press the TEMP/TIME "+" key ###⁰F or ⁰C (Oven Sensor Temperature)
## (Hours of
(Hours of operation atoperation
*Press “START”
*Pressor “STARTtoTIME”
"START" tofault
clear all clearcodes
all fault codes
1- 12
TS# W10198581
Wiring Information
R
Quick Connect Plugs
For controls Connectors For cooktop
CON3 CON1 CON2

BU W BU BK
BK OR
Y BU
GY BR BK
Right Side Left Side
BK/W Cooktop Cooktop
V
V
PIN 1
PIN 1
CON 1
CON 3
PIN 1
PIN 1
CON 2
CON 4
1-13
LCC Self-Clean, Gas
LCC95 Control, Self-Clean, Gas
Models:
TGS325VB0
TGS325VB1
TGS325VQ0
TGS325VQ1
TGS325VT0
TGS325VT1

Models:
WFG361LVB0 WFG371LVS0
WFG361LVB1 WFG371LVS1
WFG361LVD0 WFG374LVB0
WFG361LVD1 WFG374LVB1
WFG361LVQ0 WFG374LVD0
WFG361LVQ1 WFG374LVD1
WFG361LVS0 WFG374LVQ0
WFG361LVS1 WFG374LVQ1
WFG361LVT0 WFG374LVS0
WFG361LVT1 WFG374LVS1
WFG371LVB0 WFG381LVB0
WFG371LVB1 WFG381LVB1
WFG371LVD0 WFG381LVQ0
WFG371LVD1 WFG381LVQ1
WFG371LVQ0 WFG381LVS0
WFG371LVQ1 WFG381LVS1
Models:
MGR7661WB0
MGR7661WB1
MGR7661WS0
MGR7661WS1
MGR7661WW0
MGR7661WW1
Staples, Debra L. | Released

1- 14
LCC Self-Clean, Gas (continued)
Models:
MGR7662WB0 MGR7662WW1
MGR7662WB1 MGR7665WB0
MGR7662WQ0 MGR7665WB1
MGR7662WQ1 MGR7665WS0
MGR7662WS0 MGR7665WS1
MGR7662WS1 MGR7665WW0
MGR7662WW0 MGR7665WW1

Models:
AGR5844VDB0 AGR5844VDS0
AGR5844VDD0 AGR5844VDW0
2.
1. Press
Press TEMP/TIME "+" or "-".
BAKE for 5 seconds. Previous Offset shown, or U-00 is displayed.
between -30⁰F and +30⁰F.
Adjusts
Bake andtemperature in 10⁰ F (5⁰
Broil Temperatures are C) increments
offset
between -30⁰Ftoand
automatically the+30⁰F.
same degree.
3. Press START. Bake and Broil Temperatures are offset
3. Press START. is ignored.
is ignored.
Diagnostic Mode
Action Diagnostic ModeDisplay
2. Action "+" key
Press the TEMP/TIME ###⁰F or ⁰C Display
(Oven Sensor Temperature)
1. Press CANCEL/CANCEL/START
Press "+" again "tSt"
-30⁰F to +30⁰F (YouOffset
(Oven are in Temperature)
the test mode)
2. Press the TEMP/TIME
"+" again "+" key ###⁰F
### or ⁰C (Oven Sensor Temperature)
(Control Software Version)
Press"+""+" again
again -30⁰F to +30⁰F
### (Oven Offset
(Control Temperature)
Memory Checksum)
"+" again ###
"CLr" (Control Software
(GoodVersion)
Control)
"+" again will "+"display
again 1 of the 3
###
F# (Control Memory Checksum)
*(Error Code - See Tech Sheet for Repair) ##
"CLr" of operation
##
(Hours (Hours ofat operation
error code) (Good Control)
at error code)
"+" again will display
"+" again 1 of the 3 F#
#### *(Error Code(Total hours of ovenfor
- See Tech Sheet Repair) ##
operation)
"+" again (Hours(Door
"00" of operation
Open) orat"01"error(Door
code)Closed)
"+" again
*Press “START”
*Press or #### to START”
“DELAY
"START" clear all to (Total
clear
fault codes hourscodes
all fault of oven operation)
When checking for fault codes, if the display1-shows
15 "CLr", Do Not replace the control.
Wiring Diagram
Verify proper operation after servicing. Wiring Information

Caution: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerousTS# W10198635
operation.
L1 Oven Control LCC95 Y GY Door Position Switch

CON3-3
BU GY Door Latch Switch
CON3-1
BK GY Strip Circuits
CON3-4
The following individual circuits are for use in diagnoses, and are shown in the ON position. Do not continue with the diagnosis of the appliance if a fuse
is blown, a circuit breaker is tripped, or if thereCON3-9 V +10%/-15% volt power supplyOven
is less than a 240 Temp
at the wallSensor
outlet. N
V W
N
L1 Oven Light (K2)
CON3-10
CON1-5 BK DSI Board
Surface Burner Ignition Switch J1-4 W 40 WW
Oven Light Assy W
CON1-1 W Burner W
Power Supply
BK Burner
CON2-4 Latch Motor (K1) CON1-4 BR Burner
Latch Motor 4 W W
BK BK BK R R/BK J1-9 Burner
Bake (K7) CON2-7 DSI Board
BK J1-10 J1-1
GND
J1-4 W
Broil (K6) CON2-1 R
G GND
Strip Circuit
BakeTable
Valve Burner
Broil Valve
From To Results J1-2
Notes Burner
OR
Burner
Door switch Con 3-3
Surface Burner Con 3-4
Ignition Switch Door open = open circuit
Door closed = closed circuit J1-3 Burner
BU
Latch motor Con 1-4 W (Neutral) 500 - 3000Ω Latch motor locks door at start
R/W J1-6
of clean cycle
BU/W J1-7
Oven temperature Con 3-9 Con 3-10 1000 - 1200Ω at room temperature DisconnectBroil
connector Con 3 from control
BK
sensor BK R R/BK J1-9
before measuring oven temperature
sensor Bake
BK J1-10 GND
GND
Oven light Con 1-5 W (Neutral) 0 - 40Ω nominal GND
Latch switch Con 3-1 Con 3-4 Door open = open circuit
Door closed = closed circuit
LEGEND
Quick Connect Plugs
For controls Connectors CON1-2 = Connector 1 Multiple
Functions / Circuitry
CON1 Position 2
CON3 CON1 CON2 DSI
PIN 1
PIN 1
CON 1
3 CON 3
BU W BU/W R PIN 1
OR CON 2
Y BU
GY BR BK W
BK
R/W
R/W BU/W
V R/BK
V BK
1- 16
W10198635B
NOTE: This sheet contains important Technical Service Data.
NOTES
1-17
NOT
LCC Control, Self Clean, Gas
LCC190 Control, Self Clean, Gas

Models:
MGR8670WB0
MGR8670WB1
MGR8670WQ0
MGR8670WQ1
MGR8670WS0
MGR8670WS1
MGR8670WW0
MGR8670WW1
Press
Press TEMP/TIME
TEMP/TIME or “+” or “-”. Adjusts temperature in 10⁰ F (5⁰ C) increments
TEMP/HOUR "+" or "-". between -30⁰F and +30⁰F.
Press START.
is ignored.
B, D, E, F, M
Diagnostic Mode
Action Display
Press CANCEL/CANCEL/START. "tESt" (You are in the test mode)
Press the TEMP/TIME or
Press TEMP/TIME “+” key. ###⁰F or ⁰C (Oven Sensor Temperature)
TEMP/HOUR "+" key.
erkins, Amber F. | Released Press "+" again -30⁰F to +30⁰F (Oven Offset Temperature)
"CLr"
“GOOd” (Good Control)
##
(Hours (Hours of
of operation at operation
*Press*Press
“DELAY START”
"START" to clear
to clear all fault
all fault codes
codes.
When checking for fault codes and "GOOd" is displayed, do not replace the control.
1- 18
Wiring Diagram
TE: Schematic shows door latch switch in the COOK position with oven door open and elements off.
Wiring Information TS# W10239472

Caution: Label all wires prior
NOTE: to disconnection
Schematic when
shows door latch servicing
switch controls.
in the COOK Wiring
position errors
with oven can
door cause
open improperoff.
and elements and dangerous operation.
L1 Oven Control LCC190 CON 3-3 Y GY Door Position Switch

CON 3-1
BK GY
CON 3-4 N
CON 3-9 V Oven Temp Sensor
V W
CON 3-10
Oven Light (K2) CON 1-5 BK W
Oven Light Assy 40W
CON 1-1 W
Power Supply
Con 2-4 Latch Motor (K4) CON 1-4 BR Latch Motor 4W W

BK
Bake (K7) CON 2-7 R/W
Broil (K6) CON 2-1 BU/W R Y W
Bake Igniter Bake Valve

Surface Burner Ignition Switch
BU R W
Broil Igniter Broil Valve
W
BK BK T T
FOR SERVICE TECHNICIAN’S USE ONLY L1 N G

Connectors
Quick Connect Plugs
For controls Burner
CON3 CON1 CON2 DSI PIN 1 Burner

PIN 1
CON 1
CON 3 Burner
BU W BU/W R PIN 1
PIN 1 Burner
CON 2
OR CON 4
Burner
Y BU
Spark Module GND
GY BR BK W
BK
LEGEND
R/W
R/W BU/W
CON1 Position 2 Functions / Circuitry
V
Terminals (Splice) Connection ModelsR/BK Connection
V BK
Conn Pin Function

CON 1 1 Control neutral
4 Latch motor
CON 2
5
1
1-19
Convection fan
Broil
4 LI input
7 Bake
LCC Control, Self Clean, Convection, Electric
LCC190 Control, Self Clean, Convection, Steam Clean, Electric

Models:
WFE381LVB0
WFE381LVQ0
WFE381LVS0
YWFE381LVB0
YWFE381LVQ0
YWFE381LVS0
LCC190 Control, Self Clean, Convection, Electric

Models:
MER7765WB0
MER7765WB1
MER7765WS0
MER7765WS1
MER7765WW0
MER7765WW1
YMER7765WB0
YMER7765WB1
YMER7765WS0
YMER7765WS1
YMER7765WW0
YMER7765WW1
LCC190 Control, Self Clean, Convection, Steam Clean Electric

wed by Staples, Debra L. | Released
Models:
MER7775WB0
MER7775WB1
MER7775WS0
MER7775WS1
MER7775WW0
MER7775WW1
1- 20
LCC Control, Self Clean, Convection, Electric (continued)
LCC190 Control, Self Clean, Convection, Electric
Models:
MER8770WB0
MER8770WQ0
MER8770WS0
MER8770WW0
YMERH770WB0
YMERH770WB1
YMERH770WS0
YMERH770WS1
YMERH770WW0
YMERH770WW1
LCC190 Control, Self-Clean, Convection, Electric
Models:
AER6011VAB0
AER6011VAS0
AER6011VAW0
Press TEMP/TIME or Temperature Adjustment
TEMP/HOUR "+" or "-".
Press BAKE for 5 seconds. between -30⁰F and
Previous Offset +30⁰F.
shown, or U-00 is displayed.
Press Bake and Broil Temperatures are offset
PressTEMP/TIME
TEMP/TIMEor Adjusts temperature in 10⁰ F (5⁰ C) increments
“+” or “-”. automatically to the same degree.
TEMP/HOUR
Press START. "+" or "-". between -30⁰F and +30⁰F.
If START
Bake andisBroil
offset adjustment
is ignored.
Press START.
ebra L. | Released
is ignored. B, D, E, F, M,
erkins, Amber F. | Released
Diagnostic Mode
B, D, E, F, M,
Action Display
Press CANCEL/CANCEL/START. Diagnostic
"tESt" Mode (You are in the test mode)
Action“+”
Press the TEMP/TIME
Press TEMP/TIME or
key. ###⁰F or ⁰C Display
TEMP/HOUR "+" key.
"+" again ###⁰F or ⁰C
### (Oven Sensor
(Control Temperature)
Software Version)
TEMP/HOUR "+" key.
"CLr"
“GOOd” (Good Control)
"+" again ### (Hours of (Control Memory Checksum)
##
(Hours of operation at operation
(Hours of operation at error code)
*Press “START TIME” or “DELAY
*Press "START" to clearSTART” to clear all fault codes
all fault codes.
1-21all fault codes.
*Press "START" to clear
Wiring Information
TS# W10198584
Wiring Diagram
L2
L1
N
BK BK W/BU W/BU W/BU W/BU
SC Lock Switch Oven Light Assy 40W W Oven Light Switch W
W/BU
BK Door Position Switch W R
Oven Control LCC190 CON3-3
Y Y
Door Latch Switch
CON3-1
BU BU
CON3-4
GY Oven Temp Sensor
CON3-9
V
CON3-10
V
Power Supply CON1-1
CV Motor (K2) W
CON1-5 Convection Fan Motor W
Latch Motor (K1) OR
CON2-4 CON1-4 Latch Motor 4W W
BK Bake (K4) BR Bake 2400W
CON2-7 R
R
Broil (K3) CON2-1 Broil 3400W BU/W Thermo Fuse R
DLB (K5) BU Opens @ 184˚C (363˚F)
CON4
R
CON4
Quick
R Connect Plugs Hot Surface
Indicator Lights
For controls 2B Connectors1B For cooktop
BK BK OR OR OR PK W
P2 4A 1A 1600W
BK CON3 4 CON1
OR/W CON2
1A 1900W 2A 2 LF P1
OR/BK OR OR R
S1 BU S2 W BU Left Front Element BK
BK LF V
2B 1B BK OR
Y
L1 H1 1A 1200W 2A H2 LR L2
BK Y Y/BK
BU
Y Y R
P Left Rear Element
GY
LR VBR BK BK 2B
1B Right Side Left Side
BK
H1 OR 1A 1200W
BU BU BU Cooktop H2
Cooktop
L1 2A RR L2
BK BU/BK Right Rear Element BU BU R
P
RR V
2B 1B
R BR
P2 4A 1A 1600W
BK BR/W
4 1A 1200W 2A 2 RF P1
BR/BK
S1 VS2 Right Front Element
BR BR R
BK RF V Cooktop On
V
Infinite Switches
Ind Light
(Cycles ON/OFF When Hot) V W
(On When Any Burner
Is Turned On)
PIN 1
PIN 1
2B 1B
BK T T CON 1
100W
1 6 CON 3 2A 1A
BK GY Warming Element W
5 2 PIN 1
BK V W
Warm Zone Switch PIN 1 Warm Zone
CON 2
On Ind Light
CON 4
GND
LEGEND
1- 22 CON1 Position 2 Functions / Circuitry
NOTES
1-23
LCC Self Clean, Convection, Gas
LCC190 Control, Self Clean, Convection, Gas
Models:
MGR7775WB0
MGR7775WB1
MGR7775WS0
MGR7775WS1
MGR7775WW0
MGR7775WW1
LCC190 Control, Self-Clean, Convection, Gas

Models:
AGR6011VDB0
AGR6011VDB1
AGR6011VDS0
AGR6011VDS1
AGR6011VDW0
AGR6011VDW1
Press TEMP/TIME or Temperature Adjustment
TEMP/HOUR
Press BAKE for"+" or "-".
5 seconds. between Offset
Previous -30⁰F and +30⁰F.
shown, or U-00 is displayed.
Press
PressTEMP/TIME
TEMP/TIMEor “+” or “-”. Adjusts temperature in 10⁰ F (5⁰ C) increments
TEMP/HOUR
Press START. "+" or "-". between -30⁰F and +30⁰F.
If START
Bake andisBroil
offset adjustment
is ignored.
Press START.
des, Debra L. | Released
is ignored. B, D, E, F, M
Diagnostic Mode
Action Display B, D, E, F, M
Press CANCEL/CANCEL/START. Diagnostic
"tESt" Mode (You are in the test mode)
Action“+” key.
Press TEMP/TIME ###⁰F or ⁰C Display
TEMP/HOUR "+" key.
"+" again ### or ⁰C
###⁰F (Control
(Oven Software
Sensor Version)
Temperature)
TEMP/HOUR "+" "+" again
key. ### (Control Memory Checksum)
Press "+" again -30⁰F to +30⁰F
"CLr" (Oven Offset Temperature)
(Good Control)
“GOOd”
"+"display
"+" again will again 1 of the 3 ###
F# *(ErrorCode
*(Error Code -(Control
- SeeSee Tech
Tech Software
Sheet
Sheet Version)
forfor Repair)
Repair) ##
"+" again ###
## (Hours (Control
of
(Hours of operation at error code) Memory
operation atChecksum)
error code)
"+" again "CLr"
#### (Total hours of oven (Good Control)
operation)
"+" again will again 1 of the 3 F#
"+"display "00" (Door*(Error
Open) orCode
"01"- See Tech
(Door Sheet for Repair) ##
Closed)
*Press “START *Press (Hours
TIME”"START"
or “DELAYof operation
START”
to clear at error
to clear
all fault code)
codes.all fault codes
When checking for fault codes and "GOOd" is displayed, do hours
"+" again #### (Total of oven
not replace operation)
the control.
*Press "START" to1-clear
24 all fault codes.
Wiring Diagram
TS# W10198636
Wiring Information
Caution: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation.
L1
N
BK BK W/BU W/BU W/BU W/BU
SC Lock Switch Oven Light Assy 40 W Oven Light Switch
W W
W/BU
Oven Control LCC190 CON3-3

Y GY Door Position Switch
CON3-1
BK GY W
CON3-4
V Oven Temp Sensor
CON3-9
V
CON3-10
CON1-1 W
Power Supply
CV Motor (K2) CON1-5 BU Convection Fan Motor W
CON2-4 Latch Motor (K4) CON1-4 BR Latch Motor 4 W W

BK
Bake (K7) CON2-7 DSI Board
J1-1 J1-4 W
Broil (K6) CON2-1 R
Bake Valve Burner

Broil Valve
J1-2 Burner
OR
Burner
Surface Burner Ignition Switch J1-3 Burner
BU
R/W J1-6
BU/W J1-7
Broil
BK BK R R/BK J1-9 Bake
FOR SERVICE TECHNICIAN’S USE ONLY BK J1-10 GND
G
GND
GND
Quick Connect Plugs
Connectors
For controls
CON3 CON1 CON2 DSI

LEGEND PIN 1 PIN 1
CON 1
CON 3
BU W
Component
BU/W
Connection No On Some
R In Line CON1 Position 2 Functions / Circuitry
Enclosed Within
PIN 1
PIN 1
Terminals (Splice) Connection Models Connection CON 2
OR CON 4
Y BU
GY BR BK W
BK
4
R/W
R/W BU/W
V R/BK
V BK
1-25
Conn Pin Function
CON 1 1 Control neutral
LCC Fault Code Procedure
Electrical Shock Hazard Eletrical Shock Hazard
CLr/Good - Control is good do not replace

No Display - Control Blank • Verify voltage at power supply.
• Verify voltage between control board
and terminal block by completing
the following steps:
1. Unplug range or disconnect power.
2. Connect voltage measurement
equipment to control board and
terminal block.
3. Plug in range or reconnect power
and confirm voltage reading.
• Verify voltage between CON 2-4 and
CON 1-1 by completing the following
steps:
equipment to CON 2-4 and CON 1-1.
• If voltage checks are good, unplug
range or disconnect power and
replace control panel.
1- 26
LCC Fault Code Procedure (continued)
All F1 E* Codes (Control) • Run Diagnostic Mode and verify
fault code
• Unplug range or disconnect power.
• Replace Control
F2 Fault Code (Stuck Key on Control) • Run Diagnostic Mode and verify
fault code
Replace Control
All F3 E* (Sensor) • Run Diagnostic Mode and verify

fault code
• Check Sensor for 1000-1200 Ω at
CON3-9 to CON3-10
• Check Sensor for short to ground
• If checks are not correct -
Replace Sensor
F5 E0 F5 E2 (Door Switch) • Run Diagnostic Mode and

verify fault code
• Unplug range or disconnect
power.
• Check door switch for
continuity with door open and
door closed at CON3-4 to CON3-3
Door Open -Infinite Resistance
Door Closed - 0 resistance
Replace Door Switch

1-27
LCC Fault Code Procedure (continued)
F5 E1 (Door Latch Switch) • Run Diagnostic Mode and verify

fault code
• While in Diagnostic Mode - Start
Clean cycle, to verify door does latch.
If door did not latch - check for
contunity at CON3-4 to CON3-1
• If no contunity - check for 500-3000Ω
resistance at CON1-4 to CON1-1
• If resistance check fails - replace
Latch motor.
• If resistance check is good, check
door (slot) and latching rod
alignment.
• If door alignment is good -
• Replace Door Latch Switch
1- 28
NOTES
2- 1
MRC Convection, Electric
MRC Control, True Convection, Steam Clean, Electric
Models:
GFE461LVB0
GFE461LVQ0
GFE461LVS0
GFE461LVT0
YGFE461LVB0
YGFE461LVQ0
YGFE461LVS0
MRC Control, True Convection, Warming Drawer, Steam Clean, Electric
Models:
GFE471LVB0
GFE471LVQ0
GFE471LVS0
YGFE471LVB0
YGFE471LVQ0
YGFE471LVS0
1. Press "BAKE" for 5 seconds. Previous Offset shown, or U-00 is displayed.
Temperature
Adjusts Adjustment
temperature in 5⁰F (3⁰C) increments
2. Press
1. Press "BAKE"
TEMP/TIME
for 5"+" or "-".
seconds. Previous
between Offset shown,and
-30⁰F (-18⁰C) or U-00 is (+18⁰C).
+30⁰F displayed.
Adjusts
Bake andtemperature in 5⁰F (3⁰C)
Broil Temperatures are increments
offset
between
automatically to the same degree.(+18⁰C).
-30⁰F (-18⁰C) and +30⁰F
3. Press START. Bake andisBroil Temperatures
If START not pressed within are offset
1 minute,
automatically to the
adjustment is ignored. same degree.
3. Press START.
Diagnostic Mode
Action Diagnostic Mode Display
1. Press CANCEL/CANCEL/START "TEST ON" ##⁰F "UO" (In the test mode)
2. Action
Press the TEMP/TIME "+" key "USAGE" Display
(Displays hours of Operation)
Press "+" again "TEST ON" ##⁰F "UO"
"ENG MODE" (Manufacturing(In the test mode)
Information)
2. Press the TEMP/TIME
"+" again "+" key "USAGE"
"TEST MODE" (Manual (Displays
checkhours of Operation)
of Control relays)
Press
"+""+" again
again "ENG MODE"
"VERSION" (Manufacturing Information)
(Manufacturing Information)
"+" again "TEST MODE" (Manual
"DISPLAY" check of
(Checks all Control
LEDs in relays)
Display)
"+" again "VERSION"
"CONTROL RESET" (Manufacturing (Resets ControlInformation)
settings)
"+" again "DISPLAY"
"FAULTS" (Checks all LEDs
*(Displays in Display)
all Fault Codes)
"+" again "AUTO TEST"
"CONTROL RESET" (Performs a complete
(Resets check of
Control settings)
"+" again
"+" again the OVEN, automatically)
"FAULTS" *(Displays all Fault Codes)
When in the Diagnostic mode, instructions"AUTO
will TEST"
be provided (Performs
by the a complete
control to helpcheck
you of
"+" again
through each of the programs. Press Cancel the OVEN,
to exit automatically)
the test at any time.
When in theTEST"
The "AUTO Diagnostic mode,
program will instructions
automatically will beall
test provided
the oven bycircuits.
the controlThistotest
help you easy
is very
through each
to use and whenof the
theprograms. Press Cancel
test is complete, to exitwill
test results thebetest at any time.
provided. Whenever servicing the
The "AUTO
oven, this isTEST" program
the test to run.will automatically test all the oven circuits. This test is very easy
to use and when the test *Press “START
is*Press StartTIME”
complete, test to clear
results
Time to clear allfault
willall
be faultcodes
codes
provided. Whenever servicing the
oven, this is the test to run.
When checking for fault codes*Pressand
Start
"NO Time to clearisall
FAULTS" fault codes
displayed, do not change the control.
2- 2 is displayed, do not change the control.

When checking for fault codes and "NO FAULTS"
MRC Convection, Electric (continued)
MRC Control, Fan Convection, Electric
Models:
MER8772WB0 YMER8772WS1
MER8772WB1 YMER8772WW0
MER8772WS0 YMER8772WW1
MER8772WS1 YMERH770WB0
MER8772WW0 YMERH770WB1
MER8772WW1 YMERH770WS0
YMER8772WB0 YMERH770WS1
YMER8772WB1 YMERH770WW0
YMER8772WS0 YMERH770WW1
MRC Control, True Convection, Electric
Models:
MER8875WB0 YMER8875WB0
MER8875WB1 YMER8875WB1
MER8875WS0 YMER8875WS0
MER8875WS1 YMER8875WS1
MER8875WW0 YMER8875WW0
MER8875WW1 YMER8875WW1
Press "OVEN LIGHT" for 5 seconds. Previous Offset shown, or U-00 is displayed.
Temperature
Adjusts Adjustment
Press
Press TEMP/TIME "+"for
"OVEN LIGHT" or5"-".
seconds. Previous Offset
between shown,and
-30⁰F (-18⁰C) or U-00 is (+18⁰C).
+30⁰F displayed.
Bake and
Adjusts Broil Temperatures
temperature are increments
in 5⁰F (3⁰C) offset
automatically
between -30⁰Fto(-18⁰C)
the same
anddegree.
+30⁰F (+18⁰C).
Press START.
Bake andisBroil
If START Temperatures
not pressed within are offset adjustment
1 minute,
automatically
is ignored. to the same degree.
Press START.
is ignored.
Diagnostic Mode
Action Display
Diagnostic Mode
"TEST ON" ##⁰F "UO" (In the test mode)
2. Action"+" key
Press the TEMP/TIME "USAGE" Display
(Displays hours of Operation)
1. Press "+" again
Press CANCEL/CANCEL/START "ENG
"TEST MODE"
ON" ##⁰F "UO" (Manufacturing(In the Information)
test mode)
2. "+" again "+" key
Press the TEMP/TIME "TEST
"USAGE" MODE" (Manual Check
(Displays of Control
hours relays)
of Operation)
"+""+"
Press again
again "VERSION"
"ENG MODE" (Manufacturing Information)
"+" again "DISPLAY"
"TEST MODE" (Manual (Checks
Check all LEDs in Display)
of Control relays)
"+" again "CONTROL
"VERSION" RESET" (Resets Control
(Manufacturing Information)settings)
"+" again "FAULTS"
"DISPLAY" *(Displays
(Checks all Fault
all LEDs Codes)
in Display)
"+" again "AUTO TEST"
"CONTROL RESET" (Performs a complete
(Resets check of
Control settings)
"+" again the OVEN, automatically) *(Displays all Fault Codes)
"FAULTS"
When in the Diagnostic mode, instructions will be provided
"AUTO TEST" by the control to
(Performs help you through
a complete check of
each of the programs. Press Cancel to exit the OVEN,
"+" again test at any time.
automatically)
The
When"AUTO
in theTEST" program
Diagnostic will instructions
mode, automatically test
will beall the oven
provided bycircuits.
the controlThistotest
helpis very easy to use
you through
and when the test is complete, test results will be provided.
each of the programs. Press Cancel to exit the test at any time. Whenever servicing the oven, this is
the
The test
"AUTOto run.
TEST" program will automatically test all the oven circuits. This test is very easy to use
*Press
and when the test is complete, “DELAY
*Press
test"DelaySTART”
resultsStart" toprovided.
will beto clearallallfault
clear faultcodes.
Whenever codesservicing the oven, this is
When
the test checking for fault codes and "NO FAULTS" is displayed, do not change the control.
to run.
*Press "Delay Start" to clear all fault codes.
When checking for fault codes and "NO FAULTS" 2- 3 is displayed, do not change the control.
Wiring Diagram
G L2
L1 N
Oven Control MRC P6-5 GND
W R
BK P6-1 Power Supply P6-3 FOR SERVICE TECHNICIAN’S USE ONLY
BK Warming Drawer (K5) W Warming Drawer W
P4-1 P4-2 Wiring Diagram
BK OR/BK
NOTE: Schematic shows door latchWarming Drawer
switch in the COOKTemp Sensor
position with oven door open and elements off. W
P10-3
GY L2
L1 P10-4 N
Oven
GY Control MRC
R
BK P6-1 P6-3 Door Position Switch W
P7-5 Power Supply
BK Y Y WDoor Latch Switch W
P7-6
BU BU
P7-4
GY Oven Temp Sensor Door Position Switch
P10-1 P7-5
Y GY Door Latch Switch
V P7-6
P10-2 P7-4
BU GY
V
P2-1 Quick
Convect (K4) Connect P2-3 PlugsConvect ElementP10-1 1600W
GY
V
Oven Temp Sensor
P10-2
BK
P1-3 For controls
Bake (K2) P1-4
Y Bake 2400W BU/W V For cooktop
Convect Element
1850W R/W
P2-1 Convect (K4) P2-3 R/W
BK Broil (K3) BK/W R R
Bake (K2)Broil 3400W
R Y Thermo Fuse R/W
P2-4 P1-1
P1-3 P1-4 Bake 3600W R/W
BK BK R
P1-1 BU/W Broil 3600W Hi Limit
P2-4 BU Broil (K3) Opens @ 184˚C (363˚F) R/W
DLB (K1) P3-1 Switch
P1 (Blue) P3 (White) P5 (Blue) BK P10P3-2 (Yellow) R/W
DLB (K1) P3-1
P3-2
BU
R/W
BK/W
H1 Limit Switch
R R Oven Light Assy

Oven Light Assy40W
40W RR
BK R R/W R BK OvenBR
BK/W LightOR
(K6)GY V GY GY Oven Light (K6)
V P5-4 P5-4
BK/W OR Latch Motor 4W W
Latch Motor (K7) P5-3
BK/W CV Fan (K8) BR WW
Latch Motor (K7) P5-3
P5-6 P5-2 Latch Motor 4W Convection Fan
BK
BR OR BK R WW
P2 (Red) BK P4 (Green)
P5-6 P6 (Red)
CV Fan (K8) P7
P5-2(Black) Warming Center (K9) P5-1 100W
Convection
W
Fan
BK W
OR GY GY
BU W
W
Warm Zone (K9) P5-1 100W BK Warming Center R/W Hot Surface
Y BK BK OR/BK
G W BK GYGY Y GY BU Element
Indicator
W W
Light
BK
BK
BK
2B Right Side Left
1B Side
PK PK W
BK P2 BK
Warm Zone 1A T
4A 700W
Cooktop R/W
Cooktop
Quick Connect
4
OR/W Plugs
Element 1A T
1800W 2A 2 LF P1
S2 OR/BK OR OR R
On someBK/W
models Left Front Bridge Element
BK/W For controls
Connectors2A
LF GY 1B For cooktop
BK
1A
V
2B Hot Surface
H1 1800W R/W Indicator
H2
Light
L1 1B 1A LR L2
BK/W
2B Y/BK BK 2A Y Y R
OR OR LeftOR
Rear Bridge Element
BK P1 (Blue) P3 (White) BK
P5 (Blue) LR
P
P10
V (Yellow)S PK
BK/W
W
2 OR BK
800W
BK
1A' ' '
1200W
T H
H3 LF L2
L1 H1 4 GY
2 H2 RR L2
BU BK R R GY
BK OR BR BRBK
W OR BK
GY
1100W V V GY GY OR R
H1R/W BK/W
BK/W
1A' BU/BK BU BU R
P Right Rear Element W R/W
BK
V
OR/BK RR
1100W
H2B 1A' ' BK/W L2
OR/W
1A
R
2A
BK R R
L1 P2 (Red) P4
S2 (Green) P6
BK/W (Red)
Left Front ElementP7
BK/W (Black) 2B Warm Zone
1B
R/W
BK LF V 2
Y 800W Cooktop
1A H3 BU BK
RF L2
2B BR 1B 1100W GY GY R
BK Y BK BK OR/BK BK
G W G
BK H1
BR/BK
GY Y1A BU
L1 H1 1A' 1200W H2B 2A 1A 1100W H2
L2
L2
BR/W Right Side LeftLRSide R
BK P5 Y/BK L1 S2 P6Right Front Element R
Y Cooktop R
P Left Rear
RF Element
V Cooktop
On Cooktop
Infinite Switches
LR V (Cycles ON/OFF When Hot) IND Light
W GND
2B 1B
BK BK BU BU BU GY
L1 H1 1A' 1200W H2 RR L2
2A LEGEND
BK
P
BU/BK Right Rear Element BU BK R
BK BR Multiple
RR V P1-2 = Connector 1
2B Component Connection No 1BOn Some In Line
P1 Position 2 TEnclosed Within
P2 4A 1A' ' 1600W W
BK BR/W 1A' 1400W 2A 2
4 RF P1
BR/BK
Right Front Element P12 BR Warm Zone R
S2
RF V
Cooktop
P3 P2
Infinite Switches
P1 P4 P7 P10 4
(Cycles On/Off When Hot) V W
P5 Cooktop On Ind Light P6
(On When Any Burner Is Turned On)
2- 4 GND
NOTES
2- 5
MRC Convection, Gas
MRC Control, Convection, Gas
Models:
GFG461LVB0 GFG461LVT0
GFG461LVQ0 GFG464LVB0
GFG461LVQ1 GFG464LVB1
GFG461LVQ2 GFG464LVQ0
GFG461LVS0 GFG464LVQ1
GFG461LVS1 GFG464LVS0
GFG461LVS2 GFG464LVS1
MRC Control, Convection, Warming Drawer, Gas
Models:
GFG471LVB0
GFG471LVB1
GFG471LVQ0
GFG471LVQ1
GFG471LVS0
GFG471LVS1
1. Press "BAKE" for 5 seconds. Previous Offset shown, or U-00 is displayed.
Press TEMP/TIME "+"Temperature
Adjusts Adjustment
2. or "-".
1. Press "BAKE" for 5 seconds. between Offset
Previous -30⁰F (-18⁰C)
shown,and +30⁰F
or U-00 is (+18⁰C).
displayed.
Adjusts temperature in 5⁰F (3⁰C) increments
2. Press TEMP/TIME "+" or "-". automatically to the same degree.
3. Press START. between -30⁰F (-18⁰C) and +30⁰F (+18⁰C).
If START
Bake andisBroil
not Temperatures
pressed withinare
1 minute,
offset
3. Press START.
Diagnostic Mode
Action Display
1. Press CANCEL/CANCEL/START Diagnostic Mode
2. Press the TEMP/TIME "+" key "USAGE" (Displays hours of Operation)
Action
Press "+" again "ENG MODE"
Display
"+" again "TEST MODE" (Manual check of Control relays)
"+" again "VERSION" (Manufacturing Information)
Press "+" again "ENG MODE" (Manufacturing Information)
"+" again "DISPLAY" (Checks all LEDs in Display)
"+" again "TEST MODE" (Manual check of Control relays)
"+" again "CONTROL RESET" (Resets Control settings)
"+" again "FAULTS" *(Displays all Fault Codes)
"+" again "DISPLAY"
"AUTO TEST" (Checks
(Performs all LEDs incheck
a complete Display)
of
"+" again
the OVEN, automatically)
When in the Diagnostic mode, instructions will be provided by the control to help you
"AUTO TEST" (Performs a complete check of
through each of "+"the
again
programs. Press Cancel to exit the test at any time.
The "AUTO TEST" program will automatically test all the oven circuits. This test is very easy
When in the Diagnostic mode, instructions will be provided by the control to help you
to use and when the test is complete, test results will be provided. Whenever servicing the
through each of the programs. Press Cancel to exit the test at any time.
The "AUTO TEST" program will automatically
*Press test all the all
oven circuits.
codes This test is very easy
*Press“START TIME”
Start Time to to clear
clear fault
all fault codes
to use and when the test is complete, test results will be provided. Whenever servicing the
When checking for fault codes and "NO FAULTS" is displayed, do not change the control.
*Press Start Time to clear all fault codes
2- 6
Wiring Diagram
Wiring Information
NOTE: Schematic shows door latch switch in the COOK position with oven door open and elements off. TS# W10208861
Caution: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation.
L1 G
N
Oven Control MRC P6-5 GND
BK P6-1 Power Supply P6-3 W W

BK Warming Drawer (K5) W Warming Drawer W
P4-1 P4-2
BK OR/W Warming Drawer Temp Sensor
P10-3
GY
P10-4
GY
P7-5 Door Position Switch
Y Y Door Latch Switch
P7-6
BU BU
P7-4
GY Oven Temp Sensor
P10-1
V
P10-2
V
Oven Light
Assy 40W
Oven Light (K6) P5-4
P5-6 Latch Motor (K7) P5-3 BK/W Latch Motor 4W W
BK Convection Fan (K8) P5-2 BR Convection Fan W
BU W
P1-3 Bake (K2) P1-4
BK P2-4 Broil (K3) P1-1 R/W
BK BU/W
DSI Board
J1-1 J1-4
Bake Valve R W
Burner
J1-2 Burner
OR
Broil Valve Burner
Surface Burner Ignition Switch J1-3 Burner
BU
R/W J1-6
BU/W J1-7 Broil
BK BK R R/BK J1-9 Bake
BK J1-10 GND
GND
Center Cooktop Ignition Switch 5th Burner Spark Mocule W

BK BK R R Quick Connect Plugs
For controls
On some models G
DSI
L N
P1 (Blue) P5 (Blue) R
BU/W BK R/W BK BK/W BR BU OR
BU
W
P2 (Red) P6 (Red)
GND
BK G W BK R/W
Quick Connect Plugs

For controls
Connectors P7 (Black) P10 (Yellow)
BU/W
R/BK
LEGEND
GY Y BU V V BK
DSI P5 P6
P1 - 2 = Connector Multiple
P1 (Blue) Component
P5 (Blue)
Connection No On Some In Line R P1 Position 2 Functions / Circuitry
Enclosed Within
BU/W BK R/W BK BU BR
BK/W BK
BR BU BK OR
W
BU
3 W
P6 (Red)
P12
P2 (Red) P3 P2 P1 P4 P7 P10
BK BK
G W G
BK R/W
BU/W
P7 (Black) P10 (Yellow) R/BK
GY Y BU V V GY GY BK
P5 2- 7 P6 5
MRC Convection, Gas (continued)
MRC Control, Convection, Gas

Models:
MGR8772WB0
MGR8772WS0
MGR8772WW0
MGR8875WB0
MGR8875WB1
MGR8875WS0
MGR8875WS1
MGR8875WW0
MGR8875WW1
Press "OVEN LIGHT" for 5 seconds. Previous Offset shown, or U-00 is displayed.
between -30⁰F (-18⁰C) and +30⁰F (+18⁰C).
Press START.
is ignored.
Diagnostic Mode
Action Display
Press "+" again "ENG MODE" (Manufacturing Information)
"+" again "TEST MODE" (Manual Check of Control relays)
"+" again the OVEN, automatically)
When in the Diagnostic mode, instructions will be provided by the control to help you through
each of the programs. Press Cancel to exit the test at any time.
The "AUTO TEST" program will automatically test all the oven circuits. This test is very easy to use
and when the test is complete, test results will be provided. Whenever servicing the oven, this is
the test to run.
*Press “DELAY
*Press START”
"Delay Start" to clear allfault
clear all faultcodes.
codes
2- 8

Caution: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous
operation.
L1 N
Oven Control MRC
BK P6-1 P6-3 W
Power Supply
BK W
P7-5 Door Position Switch

Y Y Door Latch Switch
P7-6
BU BU
P7-4
GY Oven Temp Sensor
P10-1
V
P10-2
V
Oven Light Assy 40W

Oven Light (K6) P5-4
BK/W W
P5-6 Latch Motor (K7) P5-3 Latch Motor 4W
BK Convection Fan (K8) BR Convection Fan W
P5-2
BU W
P1-3 Bake (K2) P1-4
BK P2-4 Broil (K3) P1-1 R/W
R Y W
BK BU/W
BU R W

Broil Igniter Broil Valve
FOR SERVICE Quick
TECHNICIAN’S
Connect Plugs USE ONLY
Quick Connect Plugs
BK BK T
Connectors
For controls
For controls
T
W
P1 (Blue) P3 (White) P5 (Blue) P10 (Yellow)
P1 (Blue) P3 (White) P5 (Blue) P10 (Yellow)
BU BK R R/W R BK BK/W BR OR GY V V
BU BK R R/W R GY BR BK
BK OR BK/W W OR BK
BR GY V V L1 N G
P2 (Red) P6 (Red) P7 (Black) Burner
P2 (Red) P6 (Red) P7 (Black)
BK W BK GY Y BU Burner
BK BK W BK GY Y BU
Burner
P5 P6
P5 P6
Burner
Burner
Spark Module GND
LEGEND
P12 Multiple
P1-2 = Connector 1
P12 Functions / Circuitry
P1 P7
PositionP10
2
Component Connection P3 NoP2 OnP1
SomeP4 In Line Enclosed Within
Terminals (Splice) P3 Connection
P2 P1 Models
P4 Connection P7 P10
Conn Pin
CON P1 Pin 1
Conn
Function
Broil
Function
2-Conn
9Conn Pin
CON P6 Pin 1
Function
Control LI input
Function
CON P1 1 3 BroilBake LI input CON P6 1 3 Control
Control neutral
LI input
4 Bake CON P7 4 Latch/door switch common
MRC Fault Code Procedure
No Faults - Control is good do not replace Do Not Replace Control
No Display - Control is blank • Verify 120VAC between P6-1

to P6-3 by completing the
following steps:
1. Unplug range or disconnect
power.
equipment to P6-1 and P6-3.
3. Plug in range or reconnect
power and confirm voltage
reading.
4. Unplug range or disconnect
power.
• Check wiring from control
board to terminal block.
• Check wiring from terminal
block to power supply.

2- 10
MRC Fault Code Procedure (continued)
All F1 E* Codes (Control) • Run Diagnostic Mode and
go to "Faults" display
• Verify fault code
• power.
• Replace Control
F2 Fault Code (Stuck Key on Control) • Run Diagnostic Mode and go
to “Faults” display
power.
• Check Ribbon Connector on
Control
• If connector is good
Replace Control
F3 E0 (Sensor) • Run Diagnostic Mode and go
power.
• Check Sensor for 1000-1200 Ω
at P10-1 to P10-2
• Check Sensor for short to
ground
Replace Sensor
F3 E2 (Warming Drawer Sensor) • Run Diagnostic Mode and go

power.
• Check Sensor for 1000-1200 Ω
at P10-3 to P10-4
• Check Sensor for short to
ground
Replace Sensor

2- 11
F5 E0 (Door Switch) • Run Diagnostic Mode
and go to “Faults” display
power.
• Check for continuity with
door open and door closed
at P7-4 to P7-5
• Door Open - Infinite Resitance
• Door Closed - Zero Resistance
• If checks are not correct,
Replace Door Switch

F5 E1 (Door Latch System) • Run Diagnostic Mode and

go to "Faults" display
Verify fault code
• While in Diagnostic Mode -
Start Clean cycle, to verify
door does latch.
• Unplug range or discon-
nect power.
• If door did not latch check
for contunity at P7-4
to P7-6 if no contunity
- check for 500-3000Ω
resistance at P5-3 to P6-3
If resistance check fails
replace Latch motor.
• If resistance check is good,
check door (slot) and
latching rod alignment.
• If door alignment is good -
Replace Door Latch Switch

2- 12
All F6 E* (Control Communication) • Run Diagnostic Mode and

verify fault code
power.
• Replace Control
All F9 Fault Codes (House Miswired) • Run Diagnostic Mode and

verify fault code
power.
• Check House power supply
and verify 240VAC is
available at the wall outlet.

2- 13
Notes
3- 1
MRC II Double Oven, Electric
MRC II Control, Double Oven, Warming Zone, Electric
Models:
GGE388LXB00
GGE388LXQ00
GGE388LXS00
MRC II Control, Double Oven, True Convection (Lower)

Warming Zone, Electric
Models:
GGE390LXB00
GGE390LXQ00
GGE390LXS00
MRC II Control, Double Oven, Warming Zone, Electric

Models:
MET8665XB00
MET8665XS00
MET8665XW00
YMET8665XB00
YMET8665XS00
YMET8665XW00
3- 2
MRC II Double Oven, Electric (continued)
MRC II Control, Double Oven, Fan Convection (Lower)
Models:
MET8775XB00
MET8775XS00
MET8775XW00

Models:
MET8885XB00
MET8885XS00
MET8885XW00
YMET8885XB00
YMET8885XS00
Temperature Adjustment YMET8885XW00
Press "SETTINGS" until "Temp Calib"
is displayed. Temperature Adjustment
Press TEMP/TIME "+" or"Temp
"SETTINGS" until "-". Calib"
Previous Offset
between shown,and
-30⁰F (-18⁰C) or U-00 is (+18⁰C).
+30⁰F displayed.
is displayed.
Adjusts temperature
automatically in 5⁰Fdegree.
to the same (3⁰C) increments
Press START. between -30⁰F (-18⁰C) and +30⁰F (+18⁰C).
is ignored
Press START.
is ignored
Diagnostic Mode
Action Display
Press CANCEL/CANCEL/START. Diagnostic Mode
Action
Press the TEMP/TIME "+" keypad, "CONTROL RESET" Display
(Resets Control settings)
follow directions at each
Press CANCEL/CANCEL/START. operation. "TEST ON" ##⁰F "UO" (In the test mode)
Press "+" "USAGE" (Displays hours of Operation)
Press the TEMP/TIME "+" keypad,
"+" again "ENG MODE"
"CONTROL RESET" (Manufacturing Information)
follow directions"+"
at each
againoperation. "TEST MODE" (Manual Check of Control relays)
Press "+"
"+" again "USAGE"
"VERSION" (Displays hours of
(Manufacturing Operation)
Information)
"+" again
"+" again "ENG MODE"
"DISPLAY" (Manufacturing Information)
(Checks all LEDs in Display)
"+"
"+" again
again "TEST MODE"
"FAULTS" (Manual*(Displays
Check of Control
all Faultrelays)
Codes)
"+" again "VERSION"
"AUTO TEST" (Manufacturing
(Performs a complete Information)
check of the
"+"
"+" again
again "DISPLAY"
OVEN, automatically) (Checks all LEDs in Display)
"+" again "FAULTS" *(Displays
When in the Diagnostic mode, instructions will be provided by the control allyou
to help Fault Codes)
through
"AUTO TEST" (Performs a complete check of the
"+" again OVEN, automatically)
When
Whenin the Diagnostic
checking mode,
for Fault instructions
Codes and "NOwill be provided
FAULTS" by the control
is displayed. Do Notto help you
replace thethrough
Control.
each"AUTO
The of the programs. Presswill
TEST" program Cancel to exit the test
automatically test all
at any time. circuits. This test is very easy to
the oven
use and when the test is complete, test results will be provided. Whenever servicing the oven,
thisWhen
is thechecking for Fault Codes and "NO FAULTS" is displayed. Do Not replace the Control.
test to run.
The "AUTO TEST" program
*Press “START will
TIME
*Press automatically
or“DELAY
"DELAY test
START”
START" toall
to theall
oven
clear
clear circuits.
allfault
fault codes.This test is very easy to
codes.
this is the test to run.
3- 3
Caution: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and
dangerous operation. Verify proper operation after servicing.




 
  

 
 

 
 


 


 
  
   



  
    
  
  
  
 
     


   
 
  
 
 
  
   
     
 
   
 
 
  
  
   
   
  
  

 
  

   
 
   



      

 

 



    
On some models

 
 



Quick Connect Plugs
Connectors
 
   



    
For controls
 
 P5 (Blue)


  P7 (Black)
 P10 (Yellow) P6 (Red)
     

 BK BK
BK BK/W OR
 BK R R/W BK BU
 BU/W W W W W BK W


  


P2 (Red) P1 (Blue) P15 (Black) P11 (Neutral) P3 (Yellow) P4 (Green)




BK Y BK  ORBK V BU Y-R R R BK BR BK BU
  

     

   
 
 


 

P5  P6
  Blue     Red
 
  
 
 


   
   
 
  

P12
Black 
LEGEND
P15 P11 P3 P2 P1 P4 P14 P9 P7 P10
Black Natural Yellow Red Blue Green Green White Black Yellow
P1-2 = Connector 1 Multiple

Pin Function
Pin Function
P1 Position 2 Functions / Circuitry
Component Connection No On Some In P4
Line Enclosed Within
Models 3- 4Connection
Relay Input/Output Connector
Terminals P1 Connection
Relay Input/Output Connector
P4-1 K5 in L1E (upper broil element)
P1-1 K3 out (lower convect)
MRC II Double Oven, Electric (continued)
Models:
KERS505XBL00
KERS505XSS00
KERS505XWH00

Models:
Released
KERS507XSS00
YKER507XSS00
Press "OPTIONS" until "Temp Calib"
Previous Offset shown.
is displayed. Temperature Adjustment
Press "OPTIONS" until "Temp Calib" Adjusts temperature in 5⁰F (3⁰C) increments
Press #3 or #6 keypads. Previous Offset shown.
is displayed. between -30⁰F (-18⁰C) and +30⁰F (+18⁰C).
Bake and
Adjusts Broil Temperatures
temperature are increments
in 5⁰F (3⁰C) offset
Press #3 or #6 keypads. automatically to the same degree.
Press START. between -30⁰F (-18⁰C) and +30⁰F (+18⁰C).
Bake andisBroil
If START Temperatures
not pressed within are offset
1 minute,
automatically to the
adjustment is ignored. same degree.
Press START.
Diagnostic Mode
Action Display
Press CANCEL/CANCEL/START
OFF / Off / START Diagnostic
"TEST ON" Mode
##⁰F "UO" (In the test mode)
Action
Press the the number "3" key, follow
"CONTROL RESET"
Display
directions at each operation.
Press CANCEL/CANCEL/START "TEST ON" ##⁰F "UO" (In the test mode)
Press the thePress "3" "3"
number again
key, follow "USAGE" (Displays hours of Operation)
"3"operation.
again "CONTROL
"ENG MODE"RESET" (Resets Control
(Manufacturing settings)
Information)
directions at each
"3""3"
Press again
again "TEST MODE"
"USAGE" (Manual Check
(Displays of Control
hours relays)
of Operation)
"3"
"3" again
again "VERSION"
"ENG MODE" (Manufacturing Information)
"3" again
"3" again "DISPLAY"
"TEST MODE" (Manual (Checks
Check all LEDs in Display)
of Control relays)
"3" again
"3" again "FAULTS"
"VERSION" *(Displays allInformation)
(Manufacturing Fault Codes)
"3" "AUTO TEST" (Performs a complete
all LEDs incheck of
"3" again
again "DISPLAY" (Checks Display)
"3" again the OVEN,
"FAULTS" automatically) *(Displays all Fault Codes)
When in the Diagnostic mode, instructions "AUTO
will be provided
TEST" by the control atocomplete
(Performs help you check
through
of
"3" again
each of the programs. Press Cancel to exit the
the OVEN,
test at automatically)
any time.
When
each checking
of the programs.for Fault
PressCodes
Canceland "NOthe
to exit FAULTS"
test at is displayed.
any time. Do Not replace the Control.
The "AUTO TEST" program will automatically test all the oven circuits. This test is very easy to
useWhen
and when the test
checking is complete,
for Fault test"NO
Codes and results will beis provided.
FAULTS" displayed. Whenever servicing
Do Not replace the the oven,
Control.
*Press
*Press“DELAY
use and when the test is complete, "START START” totoclear
TIME"will
test results clear
be allallfault
provided.faultcodes.
codes. servicing the oven,
Whenever
this is the test to run. 3- 5
*Press "START TIME" to clear all fault codes.
MRC II Control, Double Oven, True Convection (Lower), Dual Fuel
MRC II Control, Double Oven, True Convection (Lower), Dual Fuel
Models:
KDRS505XSS00
is displayed.
Press #3 or #6 keypads.
between -30⁰F (-18⁰C) and +30⁰F (+18⁰C).
Press START.
Diagnostic Mode
Action Display
"CONTROL RESET" (Resets Control settings)
Press "3" again "USAGE" (Displays hours of Operation)
"3" again "ENG MODE" (Manufacturing Information)
"3" again "TEST MODE" (Manual Check of Control relays)
"3" again "VERSION" (Manufacturing Information)
"3" again "DISPLAY" (Checks all LEDs in Display)
"3" again "FAULTS" *(Displays all Fault Codes)
"3" again
When checking for Fault Codes and "NO FAULTS" is displayed. Do Not replace the Control.
“DELAY START”
3- 6
Wiring
Wiring Diagram
Information TS# W10323649
NOTE: Schematic shows
NOTE: Schematic door
shows latch
door latchswitch
switch ininthe
theCOOK
COOK position
position withdoor
with oven oven door
open andopen andoff.elements off.
elements
Control Board
Sensor
Sensor

Quick
Quick Connect Plugs
Connect Plugs
For controls
For controls
Connectors P5 P5
(Blue)
(Blue) P7(Black)
P7 (Black) P10 P10 (Yellow)
(Yellow)
BK BK BK/W BK BK RR R/W
R/WBKBKBU BU W WW W WW W
BK BK BK BK
BK/W BK BK BU/W
BU/W W
P11 (Neutral) P6 (Red) P2 (Red) P1 (Blue) P4 (Green)

P11 (Neutral) P6 (Red) P2 (Red) P1 (Blue) P4 (Green)
R R BK W BK Y BK OR BK V BK BU
R R BK W BK Y BK OR BK V BK BU
P3 (Yellow) P15 (Black)
P3 BK
(Yellow)
BR P15 (Black)
BU R
BK BR BU R
P5 P6
Blue Red
P5 P6
Blue Red
P12
Black
LEGEND P12
Black
P15 P11 P3 P2 P1 P4 P14 P9 P7 P10
P1-2 = Connector 1 Multiple

3- 7 P1 Position 2 Functions / Circuitry
Component Connection P15 P11No P3 On
P2 Some
P1 P4 In P14
Line P9 P7 P10 Enclosed Within
MRC II Double Oven, Gas
MRC II Control, Double Oven, Gas

Models:
GGG388LXB00
GGG388LXQ00
GGG388LXS00
is displayed.
between -30⁰F (-18⁰C) and +30⁰F (+18⁰C).
Press START.
is ignored
Diagnostic Mode
Action Display
Press CANCEL/CANCEL/START. "TEST ON" ##⁰F "UO" (In the test mode)
Press the TEMP/TIME "+" keypad, "CONTROL RESET" (Resets Control settings)
follow directions at each operation.
"+" again "ENG MODE" (Manufacturing Information)
“STARTSTART"
*Press "DELAY TIME” to clear all fault codes.
3- 8
TS# W10311742
Wiring Information

Quick Connect Plugs
Connectors
For controls
P5 (Blue) P7 (Black)
Quick Connect Plugs P10 (Yellow)
For controls
BK BK BK BK/W OR
BK BK R R/W BK BU BU/W W W W W
P5 (Blue) P7 (Black) P10 (Yellow)
BK BK BK BK/W BK BK R R/W BK BU BU/W W W W W
P14 (Green) P6 (Red) P2 (Red) P1 (Blue) P4 (Green)

BK BK W W BK BK R BK Y
R BK BK OR BK BK V
Y OR BK BU
Y
P5 P6
Blue Red
P5 P6
Blue Red
P12
Black
P15 P11 P3 P2 P1 P4 P14 P9 P7 P10 P12

Black Natural Yellow Red Blue Green Green White Black Yellow Black
3- 9
MRC II Control, Double Oven, Gas, (continued)
MRC II Control, Double Oven, True Covection (Lower), Gas

Models:
GGG390LXB00
GGG390LXQ00
GGG390LXS00
MRC II Control, Double Oven, Fan Convection (Lower), Gas

Models:
MGT8655XB00
MGT8655XS00
MGT8655XW00
MRC II Control, Double Oven, Fan Convection (Lower), Gas

Models:
MGT8775XB00
MGT8775XS00
MGT8775XW00
3- 10
MRC II Double Oven, Gas
MRC II Control, Double Oven, True Convection (lower), Gas
Models:
MGT8885XB00
MGT8885XS00
MGT8885XW00
is displayed.
between -30⁰F (-18⁰C) and +30⁰F (+18⁰C).
Press START.
is ignored
Diagnostic Mode
Action Display
Press CANCEL/CANCEL/START. "TEST ON" ##⁰F "UO" (In the test mode)
Press the TEMP/TIME "+" keypad, "CONTROL RESET" (Resets Control settings)
follow directions at each operation.
"+" again "ENG MODE" (Manufacturing Information)
* Press “DELAY
*Press START”
"DELAYor “START
START" toTIME” tofault
clear all clearcodes.
all fault codes.
3- 11
dangerous operation. Verify proper operation after servicing. Wiring Information TS W10311752
BK
W
Oven Control MRC II

Power Supply
BK W
Lower Door Position Switch

BU/W
Upper Door Position Switch
BU Lower Door Latch Switch
R/W Upper Door Latch Switch
R
BK Lower Oven Temp Sensor
W W W W
Upper Oven Temp Sensor
W W W W
Upper Bake (K4)
BK R R R W
Upper Broil (K5) Broil Igniter Broil Valve
BK
Y Y Y W
Lower Convect (K3) Convect 1600W
BK Lower Broil (K1) OR W

BK
Lower Bake (K2)
BK W
Upper Convect Fan (K9) OR
Lower Convect Fan - High Speed

Lower Convect Fan - High (K7)
BK BK W W
BK
Lower Convect Fan - Low (K8)
Oven Light Assy 40W
Oven Light (K6) Oven Light Assy 40W

Quick Connect Plugs
Upper Latch Motor (K10) BK Upper Latch Motor 4W W
For controls W
BK
Lower Latch Motor (K11) Lower Latch Motor 4W
Solenoid Valve (K12) BK/W P5 (Blue) P7 (Black)
W P10 (Yellow)
BK Safety
BK BK BK BK/W Solenoid
BK BK Valve for RGas
R/WCooktop
BK BU BU/W W W W W

On some models
FOR SERVICE TECHNICIAN’S USEConnectors
ONLY BK W BK R BK OR
W
BK OR BK Y
BK Quick Connect
BK Plugs T T
P5 P6
For controls Blue Red
Burner
BurnerY
P5 (Blue) P7 (Black) P10 (Yellow) BurnerY
Y
Burner
BurnerY
BK BK BK BK/W BK BK R R/W BK BU BU/W W W W W Y
Spark Module
P14 (Green) P6 (Red) P2 (Red) P1 (Blue) P4 (Green) GND P12

Black
BK W BK R BK OR BK OR BK Y
LEGEND P15 P11 P3 P2 P1 P4 P14 P9 P7 P10

P5 P6
Blue Red
Pin
P1-2 = Connector 1
Function
Pin
Multiple
Function
P1 RelayP1 PositionConnector
Input/Output 2 Functions / Circuitry
P4-1 K5 in L1E (upper broil element)
Component Connection No On Some In Line Enclosed
P4-2
Within
K5 out (upper broil element)
Terminals Connection Models Connection
P1-1 K3 out (lower convect)
P5 Low Power Relay Outputs
P1-3 K2 in L1A (lower bake in)
P5-1 K9 (upper convect fan)
P1-4 K2 out (lower bake)
P12
10
Black P5-2 K8 (lower convect fan - low)
3- 12
P2 Relay Input/Output Connector
P5-3 K7 (lower convect fan - high)
P2-1 K4 in L1C (upper bake element)
Notes
3- 13
MRC II Double Oven, True Convection (Lower), Gas
MRC II Control, Double Oven, True Convection (Lower), Gas
Models:
KGRS505XBL00
KGRS505XSS00
KGRS505XWH00
is displayed.
Press #3 or #6 keypads.
between -30⁰F (-18⁰C) and +30⁰F (+18⁰C).
Press START.
Diagnostic Mode
Action Display
"CONTROL RESET" (Resets Control settings)
Press "3" again "USAGE" (Displays hours of Operation)
"3" again "ENG MODE" (Manufacturing Information)
"3" again "TEST MODE" (Manual Check of Control relays)
"3" again "VERSION" (Manufacturing Information)
"3" again "DISPLAY" (Checks all LEDs in Display)
"3" again "FAULTS" *(Displays all Fault Codes)
"3" again
*Press“DELAY START”
3- 14
dangerous operation. Verify proper operation after servicing.

BK
W
Power Supply
BK W
Lower Door Position Switch

BU/W
Upper Door Position Switch
BU Lower Door Latch Switch
R/W Upper Door Latch Switch
R
BK Lower Oven Temp Sensor
W W W W
Upper Oven Temp Sensor
W W W W
Upper Bake (K4)
BK R R R W
Upper Broil (K5) Broil Igniter Broil Valve
BK
Y Y Y W
Lower Convect (K3) Convect 1600W
BK Lower Broil (K1) OR W

BK
Lower Bake (K2)
BK W
Upper Convect Fan (K9) OR
Lower Convect Fan - High Speed

Lower Convect Fan - High (K7)
BK BK W W
Lower Convect Fan - Low (K8) Oven Light Assy 40W
BK
Oven Light (K6) Oven Light Assy 40W
Upper Latch Motor (K10) BK Upper Latch Motor 4W W
BK W
Lower Latch Motor 4W
Lower Latch Motor (K11)
Solenoid Valve (K12) BK/W W
FOR SERVICEQuick
TECHNICIAN’S BK
Connect Plugs
USESafety
ONLY Solenoid Valve for Gas Cooktop
Connectors
Quick Connect Plugs
For controls
For controls
P5 (Blue) P7 (Black) P10 (Yellow)
P5 (Blue) P7 (Black) P10 (Yellow) W
BK BK T T
P14
P14(Green)
(Green) P6(Red)
P6 (Red) P2P2 (Red)
(Red) P1 (Blue)
P1 (Blue) Burner P4 (Green)
P4 (Green)
Burner Y
Y
BK
BK WW BK BK R BK OR
R BK ORBK ORBurner
BK ORBKY Y BK Y
Burner
Burner Y
Y
Spark Module
P5 P6
P5Blue Red P6 GND
Blue Red
LEGEND
P12
Black
P1-2 = Connector 1 P12 Multiple

P1 Position 2
Black
Terminals Connection
P15 P11
Black Natural
P3
Yellow
Models
P2
Red
P1 Connection
P4 P14
Blue Green Green
P9
White
P7
Black
P10
Yellow
P15 P11 P3 P2 P1 P4 Pin

P14 P9
Function P7 P10
Pin Function
P1 Relay Input/Output Connector 10 P4-1
Pin
K5 in L1E (upper broil element)
Function
Pin Function
P1-1 K3 out (lower convect) 3- 15 P4-1P4-2 K5 out (upper broil element)
K5 in L1E (upper broil element)
P1 P1-3 Relay Input/Output Connector
K2 in L1A (lower bake in)
P5 Low Power Relay Outputs
MRC II Fault Code Procedure
Do Not Replace Control
No Faults - Control is good do not replace

No Display - Control blank • Verify voltage at power supply.
• Verify voltage between control
board pins P6-1 and P6-3 by
completing the following steps:
equipment between control board
pins P6-1 and P6-3.
• If voltage check is good, replace
control board.
3- 16
MRC II Fault Code Procedure (continued)
All F1 E* Codes (Control) • Run Diagnostic Mode and verify
• fault Code
• Unplug range or disconnect power
• Replace Control
F2 Fault Code (Stuck Key on Control) • Run Diagnostic Mode and verify
fault Code
• Run Keyboard test
power
• If keyboard test fails -
Replace User Interface
• If keyboard test is successful -
Replace Control
F3 E0 (Upper Oven Sensor), F3 E1 (Lower Oven Sensor) • Run Diagnostic Mode and verify
fault code
• If fault code was F3 E0 - Check
upper oven sensor for 1000-1200Ω
at P10-3 to P10-4
• If fault code was F3 E1 - Check
Lower Oven Sensor for 1000-1200 Ω
at P10-1 to P10-2
• Check Sensor for short to ground.
• If checks are not correct - Replace
Sensor

3- 17
F5 E0 (Door Switch) • Run Diagnostic Mode and verify

fault code
• Check door switch for continuity with
door open and door closed :
Upper Oven at P7-4 to P7-5.
Lower Oven P7-4 to P7-6.
Door Open -Infinite Resistance
Door Closed - 0 resistance
Replace Door Switch
3- 18
F5 E1 (Door Latch System) • Run Diagnostic Mode and verify

fault code
• While in Diagnostic Mode - Start Clean
cycle, to verify that door does latch.
• If door did not latch - check for
contunity:
Upper Oven - P7-4 to P7-2
Lower Oven - P7-4 to P7-3
(Latch Switches)
• If no contunity - check for
500-3000Ω resistance at P5-6 to
P6-3 or P5-5 to P6-3 (Latch Motors)
• If resistance check fails - replace
Latch motor.
• If resistance check is good, check door
(slot) and latching rod alignment. If door
alignment is good - Replace Door Latch
Switch
All F6 E* (Control Communication) • Run Diagnostic Mode and verify fault

code
• Replace Control

All F9 Fault Codes (House Miswired) • Check House power supply and verify
240VAC is available at the wall outlet.

3- 19

Whirlpool Menus PDF

Uploaded by

Copyright:

Available Formats

Whirlpool Menus PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Whirlpool Menus PDF

Uploaded by

Copyright:

Available Formats

KR38

Troubleshooting Gas and

Prepared by: WHIRLPOOL CONSUMER CARE Job Aid W10378809

GOALS AND OBJECTIVES

LCC90 Control, Standard Clean, Electric

LCC190 Control, Standard Clean, Steam Clean, Electric

Reviewed by Genview Automated Process | Released

LCC90 Control, Standard Clean, Electric

No Diagnostic Mode Available for this Model

Wiring Information TS# operation.

DISPLAY LIKELY FAILURE CONDITION SUGGESTED CORRECTIVE ACTION PROCEDURE

Quick Connect Plugs

LCC190 Control, Self-Clean, Electric

LCC190 Control, Self-Clean, Steam Clean, Electric

LCC95 6 Self-Clean, Electric

LCC180 Control, Self-Clean, Electric

CON3 CON1 CON2

LCC190 Control, Self-Clean, Gas

Staples, Debra L. | Released

LCC95 Control, Self-Clean, Gas

Verify proper operation after servicing. Wiring Information

L1 Oven Control LCC95 Y GY Door Position Switch

LCC190 Control, Self Clean, Gas

Wiring Information TS# W10239472

L1 Oven Control LCC190 CON 3-3 Y GY Door Position Switch

Con 2-4 Latch Motor (K4) CON 1-4 BR Latch Motor 4W W

Bake Igniter Bake Valve

Broil Igniter Broil Valve

FOR SERVICE TECHNICIAN’S USE ONLY L1 N G

CON3 CON1 CON2 DSI PIN 1 Burner

Conn Pin Function

LCC190 Control, Self Clean, Convection, Steam Clean, Electric

LCC190 Control, Self Clean, Convection, Electric

LCC190 Control, Self Clean, Convection, Steam Clean Electric

LCC190 Control, Self-Clean, Convection, Gas

Oven Control LCC190 CON3-3

CV Motor (K2) CON1-5 BU Convection Fan Motor W

CON2-4 Latch Motor (K4) CON1-4 BR Latch Motor 4 W W

Bake Valve Burner

CON3 CON1 CON2 DSI

Electrical Shock Hazard Eletrical Shock Hazard

CLr/Good - Control is good do not replace

All F3 E* (Sensor) • Run Diagnostic Mode and verify

F5 E0 F5 E2 (Door Switch) • Run Diagnostic Mode and

F5 E1 (Door Latch Switch) • Run Diagnostic Mode and verify

2- 2 is displayed, do not change the control.

R R Oven Light Assy

BK P6-1 Power Supply P6-3 W W

Center Cooktop Ignition Switch 5th Burner Spark Mocule W

Quick Connect Plugs

P7 (Black) P10 (Yellow) R/BK

MRC Control, Convection, Gas

Wiring Information TS# W10239474

P7-5 Door Position Switch

Oven Light Assy 40W

FOR SERVICE TECHNICIAN’S USE ONLY

Electrical Shock Hazard Eletrical Shock Hazard

No Faults - Control is good do not replace Do Not Replace Control

No Display - Control is blank • Verify 120VAC between P6-1