Technical Data Sheet Arcapro Positioner Type 827A TD - 827A

Technical Data Sheet
TD_827A
ARCAPRO® Positioner Type 827A
General data
ARCA-integrated or to VDI/VDE 3847-1 or IEC 534-6 (NAMUR)
Mounting On linear actuators
Range of stroke: 3 ... 130 mm
On quarter turn Integrated to VDI/VDE 3847-2 or VDI/VDE 3845
actuators Angle of rotation: 30 ... 100°
Enclosure material Metal Aluminium cast AlSi 12 or austenitic stainless steel 1.4581
Degree of protection IP 66 to EN 60529

Any installation position possible; pneumatic connections and exhaust
Installation position
opening must not point upwards for wet applications
4K3, but -30 ... +80 C (Standard and FIP)
Climate class Operation -40…+80 °C (LT)
(see electrical data for explosion-protected devices)
Storage 1K5, but -40 ... +80 C
Transport 2K4, but -40 ... +80 C

98 m/s2, 27 ... 300 Hz
Vibration resistance
Recommended continuous range for complete fitting ≤ 30 m/s2
Classification according For fluid group 1 gases; fulfils requirements in article 4, paragraph 3
PED 2014/68/EU (good engineering practice)
CE marking Applicable directives and standards see declaration of conformity
Controller unit Five-point switch Adaptive
Dead zone Adaptive or fixed from 0.1 ... 10 %
Actuating times ≥1.5 s adjustable
A/D converter Resolution ≤ 0.5 %
Sampling time 10 ms
With / without HART
Cycle time 20 ms
communication
With PROFIBUS PA
60 ms
communication
With Fieldbus
Foundation 60 ms
communication
Dimensions See dimension drawing 1 and 2
Metal enclosure,
Weight Approx. 1.3 kg
aluminium
Metal enclosure,
Approx. 3.9 kg
stainless steel
Connections Electric Screw terminals 2.5 AWG28-12; cable inlet see order key
Pneumatic G 1/4 DIN 45141 or 1/4-18NPT, see order key
©ARCA Regler GmbH • Kempener Straße 18 • D-47918 Tönisvorst

Tel.: +49-(0)2156-7709-0 • Fax: +49-(0)2156-7709-55 • [email protected] • www.arca-valve.com
TD_827A_en_01-2022.doc - Subject to technical modifications - Page 1 of 15
TD_827A
Pneumatic data
Operation Standard At failure of electrical or pneumatic energy exhausting
Option Fail In Place At failure of electrical or pneumatic energy blocking
Inlet air pressure 1.4 ... 7 bar (Standard) / 3…7 bar (FIP)
Air quality Solids ISO 8573-1 Class 3
Dew point ISO 8573-1 Class 3 (-40 C, min. 20 K below ambient temperature)
Oil content ISO 8573-1 Class 3
Air consumption < 36 x 10-3 Nm3/h during stationary operation
Flow rate (unthrottled) Air supply valve at Δp 2 bar - 4,1 m3/h i.N., 4 bar - 7,1 m3/h i.N., 6 bar - 9,8 m3/h i.N.
2 bar – 8,2 Nm3/h, 4 bar – 13,7 Nm3/h, 6 bar – 19,2 Nm3/h (Standard)
Air exhaust valve at Δp
2 bar – 4,3 Nm3/h, 4 bar – 7,3 Nm3/h, 6 bar – 9,8 Nm3/h (FIP)
Valve leakage < 0,6 x 10-3 Nm3/h
Throttle ratio Up to ∞ : 1 adjustable
Electrical data for basic device
Explosion protection Intrinsic safety “ia” II2G Ex ia IIC T6/T4 Gb, Zone 1
Permissible ambient T4 / T6 - 30 ... + 80 C / - 30 ... + 60 C (Standard and FIP)
“ia” with/without HART
temperature T4 / T6 - 40 ... + 60 C / - 40 ... + 60 C (LT)
“ia” with PROFIBUS
T4 / T6 - 30 ... + 80 C / - 30 ... + 50 C (Standard and FIP)
PA / Foundation
T4 / T6 - 40 ... + 60 C / - 40 ... + 50 C (LT)
Fieldbus

TD_827A
Electrical data for basic device with / without HART 2 wire connection
Explosion protection without „ia“
Electrical connection See Figures 5 and 6 See Figures 5 and 6
Communication HART version 7
Input signal IW 4 ... 20 mA 4 ... 20 mA

Current to maintain the
≥ 3.6 mA ≥ 3.6 mA
power supply
Required load voltage
without HART 6.5 V 8.3 V
2 wire device
without HART 8.4 V -
2/3/4 wire device
with HART 6.7 V -
2 wire device
with HART - 8.8 V
2/3/4 wire device
Static destruction limit ± 40 mA -
certified intrinsically safe circuits with max.
Ui = 30 V
For connection to -
Ii = 100 mA
Pi = 1 W
Internal capacitance - 11 nF
207 µH without HART
Internal inductance -
310 µH with HART
Binary input BE1 Suitable for dry contact, max. contact load ≤ 5 μA at 3 V
Electrical isolation IW and BE1 electrically connected IW and BE1 electrically connected

TD_827A
Electrical data for basic device with / without HART 3/4 wire connection
Electrical connection See Figure 7 See Figure 7
Communication HART version 7
Input signal IW 0/4 ... 20 mA 0/4 ... 20 mA
Required load voltage 0.2 V 1.0 V
Power supply UH DC 18 … 35 V DC 18 … 30 V
Ui = 30 V
For connection to -
Ii = 100 mA
Pi = 1 W
Internal inductance - 310 µH
UH and IW electrically isolated, UH and IW electrically isolated,
Electrical isolation
IW and BE1 electrically connected IW and BE1 electrically connected
Electrical data for basic device PROFIBUS PA
Electrical connection See Figure 8

Layers 1 + 2 to PROFIBUS PA, transmission technique to IEC 1158-2, slave function layer 7 to
Communication
PROFIBUS DP to EN 50170 with extended PROFIBUS functionality
Device profile PROFIBUS PA profile B, version 3.02, over 150 objects
Response time for a
typically 10 ms
master telegram
Device address 126 in the as-delivered condition
Electrical data for basic device Foundation Fieldbus
Electrical connection See Figure 9

H1 communication to specification of the Fieldbus Foundation, group 3, class 31 PS
(Publisher/Subscriber) V 2.4
Communication
1 resource block (RB2), 1 analogue output function block (AO), 1 PID function block (PID), 1
transducer block (standard advanced positioner valve)
Physical layer profile 123, 511
Block execution times Analogue output function block 60 ms; PID function block 80 ms

TD_827A
Electrical data for basic device PROFIBUS PA / Foundation Fieldbus
Power supply Bus-powered Bus-powered
Bus voltage DC 9 ... 32 V DC 9 ... 24 V
Current consumption 10.5 mA ± 10 % 10.5 mA ± 10 %
Fault current 0 0
circuits with certified FISCO power supply with
max.
For connection to - Ui = 17,5 V
Ii = 380 mA
Pi = 5,32 W
circuits with certified barrier with max.
Ui = 24 V
-
Ii = 250 mA
Pi = 1,2 W
Internal capacitance - Negligible small
Internal inductance - 8 μH
Safety shutdown
Input resistance > 20 kΏ > 20 kΏ

Signal status 0:
DC 0 ... 4.5 V DC 0 ... 4.5 V
active
Signal status 1:
DC 13 ... 30 V DC 13 ... 30 V
inactive
Ui = 30 V
For connection to -
Ii = 100 mA
Pi = 1 W
Internal inductance - Negligible small
Bus connection and safety shutdown Bus connection and safety shutdown electrically
Electrical isolation electrically isolated, Bus connection and BE1 isolated, Bus connection and BE1 electrically
electrically connected connected

TD_827A
Electrical data for option modules – analogue module
Nominal signal range 4...20 mA, short circuit resistant 4...20 mA, short circuit resistant
Dynamic range 3.6...20.5 mA 3.6...20.5 mA
Auxiliary voltage UH +12...+35 V +12...+30 V
External load RB [kΏ] (UH [V] – 12)/I [mA] (UH [V] – 12)/I [mA]
Ui = 30 V
For connection to -
Ii = 100 mA
Pi = 1 W
Electrical isolation Disconnected from basic device Disconnected from basic device
Electrical data for option modules – binary module

Binary outputs A1, A2,
fault
Signal status “High”
Conductive, R = 1 kΏ ≥ 2.1 mA 1)
(not responded)
Signal status “Low”
Blocked, IR < 60 μA ≤ 1.2 mA 1)
(responded)
Ui = 15 V
For connection to -
Ii = 25 mA
Pi = 64 mW
Internal capacitance - 5,2 nF
1) Switching thresholds for supply to EN 60947-5-6: UH = 8.2 V, Ri = 1 kΏ

TD_827A
Electrical data for option modules – binary module (continuation)

Binary input BE2
Terminals 11/12
Auxiliary voltage UH ≤ DC 35 V ≤ 20 mA -
Signal status 0: ≤ DC 4.5 V or open ≤ DC 4.5 V or open
Signal status 1: ≥ DC 13 V ≥ DC 13 V
Input resistance > 25 kΏ > 25 kΏ
Static destruction limit ± 35 V -

For connection to - Ui = 25,2 V

Binary input BE2
Terminals 21/22
Signal state 0: Dry contact, open Dry contact, open
Signal state 1: Dry contact, closed Dry contact, closed
Contact load 3 V, 5 μA 3 V, 5 μA
Binary outputs A1, A2, fault, binary input BE2 Binary outputs A1, A2, fault, binary input BE2
terminals 11/12 disconnected from basic terminals 11/12 disconnected from basic
Electrical isolation device; device,
binary input BE2 terminals 21/22 connected to binary input BE2 terminals 21/22 connected to
basic device basic device

TD_827A
Electrical data for option modules – slot initiator module

Slotted initiators SJ2-SN or N7S20A to EN 60947-5-6 (NAMUR) for connecting to switching
Binary outputs A1, A2
amplifier, NC (normally closed) function
Signal state “High”
≥ 3 mA at Unom = 8 V ≥ 2.1 mA 1)
(not responded)
Signal state “Low”
≤ 1 mA at Unom = 8 V ≤ 1.2 mA 1)
(responded)
Ui = 15 V
For connection to Unom = 8 V
Ii = 25 mA
Pi = 64 mW
Internal inductance - 120 µH
Binary output fault

R = 1,1 kΏ ≥ 2.1 mA 1)
(not addressed)
R = 10 kΏ ≤ 1.2 mA 1)
(addressed)
UH ≤ 35 V Ui = 15 V
For connection to
I ≤ 20 mA Ii = 25 mA
Pi = 64 mW
Internal capacitance - 5.2 nF

Binary outputs A1, A2, fault disconnected Binary outputs A1, A2, fault disconnected from
from basic device basic device

TD_827A
Electrical data for option modules – contact module
Binary outputs A1, A2 dry contacts
Max. switching current 4 A AC / DC -
Max. switching voltage 250 V AC, 24 V DC -

Ui = 30 V
For connection to -
Ii = 100 mA
Pi = 750 mW
Binary output fault

R = 1,1 kΏ ≥ 2.1 mA 1)
(not responded)
R = 10 kΏ ≤ 1.2 mA 1)
(responded)
UH ≤ 35 V Ui = 15 V
For connection to
I ≤ 20 mA Ii = 25 mA
Pi = 64 mW
Internal capacitance - 5.2 nF

Binary outputs A1, A2, fault disconnected Binary outputs A1, A2, fault disconnected from
from basic device basic device

TD_827A
Figure 1 Metal enclosure, standard
Figure 2 Metal enclosure, stainless steel

TD_827A
+ 4 … 20 mA E
6 Control input
7 A
8
9 +3V
10 Binary input BE1

Figure 5 Electrical connection of 2 wire basic device
2
+ 4 … 20 mA
3
4
5
E
6 Control input
7 A
8
9 +3V
10 Binary input BE1

Figure 6 Electrical connection of 2/3/4 wire base device, 2 wire connection

TD_827A
+ 18 … 35 V
2
3
4
5
+ 0/4 … 20 mA E
6 Control input
7 A
8
9 +3V
10 Binary input BE1

Figure 7 Electrical connection of 2/3/4 wire base device, 3/4 wire connection
+  30 V 81
Input safety shutdown
82
 32 V
6 E
PROFIBUS PA Control input
7 A
8
9 +3V
10 Binary input BE1

Figure 8 Electrical connection of base device, PROFIBUS PA

TD_827A
+  30 V
81
Input safety shutdown
82
 32 V
6 E
Foundation Fieldbus Control input
7 A Stellungsregler
8
9
Input simulation release
10
Figure 9 Electrical connection of base device, Fieldbus Foundation
+ 12 … 35 V
61 E
Position
62 J feedback
Figure 10 Electrical connection of analogue module
+ 13 … 35 V
11 
12
Binary input BE2
1
21 +3V
22
+ 8,2 V
31
Fault
32
+ 8,2 V
41
Limit value A1
42
+ 8,2 V
51 Limit value A2
52
Figure 11 Electrical connection of binary module

TD_827A
+ 8,2 V
31
Fault
32
+ 8,2 V
41
Limit value A1
42
+ 8,2 V
51 Limit value A2
52
Figure 12 Electrical connection of slot initiator module
+ 8,2 V
31
Fault
32
41
Limit value A1
42
51 Limit value A2
52
Figure 13 Electrical connection of contact module

TD_827A
Order keys for ARCAPRO® type 827A
1. Series 7. Enclosure material

827A M Aluminium (single-acting only)
2. Explosion protection 1)
E Without E Stainless steel
X Explosion-proof “ia” II2G 2) 8. Pneumatics
1 Single-acting
2 Double-acting (aluminium housing excluded)
3. Connection of base device 9. Mechanical actuation

2 2 wire 0 Standard
4 2/3/4 wire 4) 1 with internal non contacting sensor 5)
2 None (for external sensor)
4. Analogue output 10. Connection thread, electric / pneumatic
0 Without analogue output G M20x1.5 / G 1/4
A Analogue module N 1/2“ NPT / 1/4“ NPT
5. Binary output M M20x1.5 / 1/4“ NPT
0 Without binary output P 1/2“ NPT / G 1/4
B Binary module
S Slot initiator module R connector M12 for input signal / G 1/4
K Contact module S connector M12 for input signal / 1/4“ NPT
6. Communication 11. Options
0 Without communication FIP Fail In Place 3)
H HART LT - 40 °C 5)
P PROFIBUS PA SA connector M12 for Analogue module 5)
F Fieldbus Foundation SB connector M12 for Binary module 5)
SS connector M12 for Slot initiator module 5)
SW connector M12 for External stroke sensor 5)
1
) ATEX and IECEx approval
2
) With HART communication 2/3/4 wire only
3
) only for stainless steel housing
4
) PROFIBUS PA and Foundation Fieldbus excluded
5
) On request
Example:
827A.E2-A0H- Positions 1 - 6
Positioner 827A – no explosion-proof – 2-wire connection – analogue module – without binary output – HART communication
M10-G-LT Positions 7 - 11
Aluminium enclosure – single-acting – mechanical actuation (standard) – connection thread electric M20x1.5 /
pneumatic G 1/4 / - 40 °C
Accessories
Mounting kits For integrated mounting ARCA linear actuators type 812
For integrated mounting ARCA linear actuators type 813
For integrated mounting on linear actuators acc. to VDI/VDE 3847-1
For mounting on linear actuators acc. to IEC 534 (NAMUR)
For integrated mounting ARCA quarter turn actuators type 840
For mounting on quarter turn actuators acc. to VDI/VDE 3845
Pressure gauge blocks Pressure gauge block for single-acting or double-acting positioner
Extern. position detection External rotary potentiometer for strokes to 130 mm or external linear potentiometer


Technical Data Sheet Arcapro Positioner Type 827A TD - 827A

Uploaded by

Copyright:

Available Formats

Technical Data Sheet Arcapro Positioner Type 827A TD - 827A

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Technical Data Sheet Arcapro Positioner Type 827A TD - 827A

Uploaded by

Copyright:

Available Formats

Technical Data Sheet

Degree of protection IP 66 to EN 60529

Transport 2K4, but -40 ... +80 C

Controller unit Five-point switch Adaptive

Dead zone Adaptive or fixed from 0.1 ... 10 %

Actuating times ≥1.5 s adjustable

A/D converter Resolution ≤ 0.5 %

Pneumatic G 1/4 DIN 45141 or 1/4-18NPT, see order key

©ARCA Regler GmbH • Kempener Straße 18 • D-47918 Tönisvorst

Operation Standard At failure of electrical or pneumatic energy exhausting

Option Fail In Place At failure of electrical or pneumatic energy blocking

Air quality Solids ISO 8573-1 Class 3

Oil content ISO 8573-1 Class 3

Air consumption < 36 x 10-3 Nm3/h during stationary operation

Throttle ratio Up to ∞ : 1 adjustable

Electrical data for basic device

©ARCA Regler GmbH • Kempener Straße 18 • D-47918 Tönisvorst

Explosion protection without „ia“

Electrical connection See Figures 5 and 6 See Figures 5 and 6

Communication HART version 7

Input signal IW 4 ... 20 mA 4 ... 20 mA

©ARCA Regler GmbH • Kempener Straße 18 • D-47918 Tönisvorst

Explosion protection without „ia“

Electrical connection See Figure 7 See Figure 7

Communication HART version 7

Input signal IW 0/4 ... 20 mA 0/4 ... 20 mA

Required load voltage 0.2 V 1.0 V

Internal inductance - 310 µH

Electrical data for basic device PROFIBUS PA

Electrical connection See Figure 8

Electrical data for basic device Foundation Fieldbus

Electrical connection See Figure 9

©ARCA Regler GmbH • Kempener Straße 18 • D-47918 Tönisvorst

Electrical data for basic device PROFIBUS PA / Foundation Fieldbus

Explosion protection without „ia“

Power supply Bus-powered Bus-powered

Bus voltage DC 9 ... 32 V DC 9 ... 24 V

Current consumption 10.5 mA ± 10 % 10.5 mA ± 10 %

Input resistance > 20 kΏ > 20 kΏ

Internal inductance - Negligible small

©ARCA Regler GmbH • Kempener Straße 18 • D-47918 Tönisvorst

Electrical data for option modules – analogue module

Explosion protection without „ia“

Electrical connection See Figure 10 See Figure 10

Dynamic range 3.6...20.5 mA 3.6...20.5 mA

Auxiliary voltage UH +12...+35 V +12...+30 V

Internal inductance - Negligible small

Electrical data for option modules – binary module

Explosion protection without „ia“

Electrical connection See Figure 11 See Figure 11

Internal inductance - Negligible small

1) Switching thresholds for supply to EN 60947-5-6: UH = 8.2 V, Ri = 1 kΏ

©ARCA Regler GmbH • Kempener Straße 18 • D-47918 Tönisvorst

Electrical data for option modules – binary module (continuation)

Explosion protection without „ia“

Signal status 0: ≤ DC 4.5 V or open ≤ DC 4.5 V or open

Input resistance > 25 kΏ > 25 kΏ

Static destruction limit ± 35 V -

Internal capacitance - Negligible small