Setting Contamination Flagging Limits

POSITION PAPER
Setting Contamination Flagging Limits

Fluid analysis looks at three major categories of fluid and equipment health: wear metals,
contamination, and fluid properties. Wear metals get a lot of focus because they are a good
indication of the equipment’s health at the time of sampling, but it is equally important to
understand the contaminants present in fluid because controlling contamination levels will
allow for optimal equipment and fluid life.
Dirt
Dirt (silica) is one of the most common lubricant contaminants. It is especially detrimental to
equipment due to its abrasiveness. Over time a small amount of dirt can cause quite a bit of
component wear.
Silicon limits are set based on component type. Gear systems can tolerate higher levels of dirt
before significant damage is done. Dirt contamination is more critical in engines, hydraulics,
turbines, and compressors and can quickly cause costly damage. Our limits are derived from
statistics as well as OEM and industry agreed-upon levels.
Severity 0 <20
Severity 1 20
Severity 2 30
Severity 3 60
Severity 4 100
General dirt flagging limits in ppm
Coolant
Coolant in oil (seen as sodium and potassium in our metals test) is primarily a concern for
engines. The presence of coolant can corrode soft metals (primarily bearings) and can
eventually lead to costly equipment repair. It can also have an effect on the lubricant viscosity
by thickening oil, which leads to boundary wear conditions.
It is important to be aware of coolant contamination at low levels so plans can be made for
future maintenance. Most coolant leaks cannot be detected through normal diagnostics until
the combined level of sodium and potassium is 400-500 ppm. We recommend investigating
the source of the leak and correcting the issue as soon as it reaches a detectable level to
prevent damage to other components such as main/rod bearings.
Soot
Soot is a normal byproduct of the combustion process in diesel engines and is present at
some level in all in-service diesel engine oil. Diesel engine oils are formulated with dispersant
additives that prevent the soot from agglomerating into large particles and keep them in
circulation so that they can be filtered out of the oil. Excessive blow-by, exhaust system
1 | Setting Contamination Flagging Limits

restrictions, and poor timing can lead to harmful levels of soot in the lubricant. Since soot
particles are abrasive in nature, they will cause engine wear if not controlled.
We use OEM recommendations to determine when to recommend investigating the cause of

high soot. After a while, the lubricating oil can no longer effectively handle the soot. Most
equipment OEMs list 5% as the warning limit for soot. When these limits are reached, a
recommendation will be given to change the lubricant and check for the cause of the high
soot.
Fuel Dilution
Fuel dilution is another common source of contamination in unleaded gasoline and diesel
engine oils. It is normal to see low levels of fuel in engine oils as a byproduct of the
combustion/ignition process. When fuel levels start to exceed 1%, the lubricant’s viscosity will
begin to decrease. As percent of fuel in oil increases, the lubricant’s ability to maintain a full
fluid film and protect against boundary wear is diminished. Fuel in oil will also dilute the
additives, which could lead to other wear and performance issues.
Some engines are more prone to high fuel dilution, but this does not mean the fuel will not
harm the engine. We base limits for fuel dilution on equipment OEM recommendations.
Particle Count
Particle count is a useful test for determining fluid and system cleanliness in filtered systems
such as hydraulics, turbines, compressors, auto/power shift transmissions, recirculation
systems, and filtered gear systems with a fluid viscosity of less than ISO 320. Particle count
testing measures all particles that have accumulated in a system, which may include metallic
and non-metallic particulate, dirt, fibers, water, biological growth, etc.
We use several key pieces of information to evaluate particle count levels.

1. Filter micron rating – The filter micron rating is the most critical piece of information
for particle count evaluation because it is a direct indication of system clearances and
equipment criticality.
2. Application – The application the equipment is used in also affects particle count
flagging. Equipment used in industrial and mining applications typically has tighter
system clearances, meaning the lubricants must maintain high levels of cleanliness to
prevent component wear.
3. Component type – If the filter micron rating is not provided, assumptions about the
clearances in the equipment and cleanliness goals will be made based on the
component type listed.
Water
Water contamination is one of the most detrimental contaminants in a lubricating system.
Water oxidizes metal, increases friction, and effects lubricant properties. While water
ingression can be harmful to any lubricating system, it is more critical in some components
than others. Because of this, our water flagging limits are largely defined by the component
type. General limits are listed below, but the fluid and equipment OEMs should be consulted
for these limits.

General water flagging limits in ppm
Engines Gear Hydraulic Transmissions Refrigeration

systems systems Compressors
Severity 0 <1000 < 1000 < 500 <1000 <150
Severity 1 1000 1000 500 1000 150
Severity 2 2000 2000 750 1500 300
Severity 3 4000 4000 1000 2000 500
Severity 4 5000 5000 5000 4000 1000
Contamination can come in many varieties, and each has its own cause, effect, and solution.
Therefore, it is no surprise each has its own flagging limit, and that limit can further depend on
the type and application of the equipment being tested. Our Data Analysts will be happy to
discuss our recommendations and the contamination found in the test results. .

Setting Contamination Flagging Limits

Uploaded by

Copyright:

Available Formats

Setting Contamination Flagging Limits

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Setting Contamination Flagging Limits

Uploaded by

Copyright:

Available Formats

POSITION PAPER

Setting Contamination Flagging Limits

1 | Setting Contamination Flagging Limits

We use OEM recommendations to determine when to recommend investigating the cause of

We use several key pieces of information to evaluate particle count levels.

2 | Setting Contamination Flagging Limits

Engines Gear Hydraulic Transmissions Refrigeration

3 | Setting Contamination Flagging Limits

You might also like