Enshan Wireless Forum: (Print This Page)

Enshan Wireless Forum
Title: [HG8245 Gigabit Edition Rescue Brick] TTL can interrupt autoboot, ask for flashing command and Flash
address [Print this page]
Author: dd1kaTime : 2016-1-8 00:57Title

: [HG8245 Gigabit Edition Rescue Brick]TTL can interrupt autoboot, ask for flashing command and Flash address
1. U-Boot 1.1.4 (Jun 21 2012 - 13:51:21)

2. U-Boot code: 90500000 -> 9051E974 BSS: -> 9055525C
3. RAM Configuration:
4. Bank #0: 90000000 64MB
5. Flash: 16MB
Entering the Huawei HG8245 cat through TTL, you can already interrupt the system boot, the method is to keep
pressing d, and then you will find that the system stops at:
1. Press d key to abort autoboot: 10

2. hisilicon #
After entering help, the following commands can be executed:
1. hisilicon # help
2. ? - alias for 'help'
3. base - print or set address offset
4. bdinfo - print Board Info structure
5. bootm - boot application image from memory
6. crc32 - checksum calculation
7. dhcp - invoke DHCP client to obtain IP/boot params
8. echo - echo args to console
9. erase - erase FLASH memory
10. flinfo - print FLASH memory information
11. fsinfo - print information about filesystems
12. fsload - load binary file from a filesystem image
13. help - print online help
14. lastword - print last word
15. loadboardinfo- download file from tftp server
16. loadflashcfg- download file from tftp server
17. loadfs - download file system from tftp server
18. loadjffs2- download file from tftp server
19. loadkernel- download file from tftp server
20. loadminisystem- download file from tftp server
21. loadsystem-download file from tftp server
22. loaduboot-download file from tftp server
23. loop - infinite loop on address range
24. ls - list files in a directory (default /)
25. md - memory display
26. mtest - simple RAM test
27. mw - memory write (fill)
28. ping - send ICMP ECHO_REQUEST to network host
29. printenv - print environment variables
30. protect - enable or disable FLASH write protection
31. rarpboot-boot image via network using RARP/TFTP protocol
32. reset - Perform RESET of the CPU
33. saveenv - save environment variables to persistent storage
34. setenv - set environment variables
35. tftp - download or upload image via network using TFTP protocol
36. update - update board software
37. vdecrest - vdecrest
38. vencrest- vencrest
39. version - print monitor version
You can also see the relevant configuration by entering printenv
1. hisilicon # printenv
2. bootdelay=1
3. baudrate=115200
4. ethaddr=00:00:00:00:00:02
5. ipaddr=192.168.0.10
6. serverip=192.168.0.1
7. netmask=255.255.255.0
8. bootfile="Image"
9. stdin=serial
10. stdout=serial
11. stderr=serial
12. verify=n
13. filesize=2
14. bootcmd=bootm 0x20060054 0x91000000
15. bootargs=noalign mem=50M console=ttyAMA0,115200 root=/dev/ram0 rootfstype=squashfs
mtdparts=hisilicon:0x40000(boot)ro,0x1000(flashcfg)ro,0x1f000(syspara)ro,0x180000(krnl)ro,0x8fffac@
0x1e0054(rootfs)ro,0x248fd8@0xc17028(minisystem)ro,0x180000(jffs2cfg),-(reserved) user_debug=0x1f
panic=1
However, in this mode, because the flash offset value is not known, the flash cannot be erased and re-flashed. In
addition, Huawei does not provide the conventional cp.b copy memory file to flash function in U-boot mode, only
There are commands such as loadsystem and loaduboot to directly write to the flash memory, which involves
unpacking the firmware of each version. I don’t know how to split the bin firmware into separate files such as
uboot and system? Ask the forum for your help. At present, my two 8245s are all bricks, and the system enters an
infinite loop when loading the wireless network module, can ping, cannot telnet, cannot web, and ttl input has no
response.
Many thanks!
Author: Routing Destroyer Time: 2016-1-8 12:11

Help your programmer write it, Ma Huateng 1976421907 Secret language 8245
Author: dd1kaTime : 2016-1-8 12:16
Quote: Routing Destroyer Posted at 2016-1-8 12:11

Help your programmer write it, Ma Huateng 1976421907 Secret language 8245
Thanks brother, it's too much trouble, I have to send it over by the machine, sweat. .
Author: palmy888 Time: 2016-1-11 21:32

Can't be interrupted, under my startup information, please guide
/*..............
System start
...... .........*/
U-Boot 1.1.4 (Jul 31 2013 - 16:25:21)
U-Boot code: 90500000 -> 9051FC94 BSS: -> 9054658C
RAM Configuration:
Bank #0: 90000000 64 MB
Flash: 16 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Extend LSW IS AR8316
Initialize broadcast table ... ok
CPURTx Driver For Pilot <Board-A>!
### JFFS2 loading 'fsok' to 0x904bfe84
Scanning JFFS2 FS: . done.
### JFFS2 load complete: 2 bytes loaded to 0x904bfe84
No board type file!
ui_board_id = 2
[main.c__3719]::Magic1:0x0, magic2 0x0, count 0, flag 0, MainAreaOK 0, slaveAreaOK 0
[main.c_3784]Start from normal system!
Magic1:0x5a5a5a5a, magic2 0xa5a5a5a5, count 0, flag 0
Addr[0]:0x0,Addr[1]:0x40000,Addr[2]:0x41000,Addr[3]:0x60000,Addr[4]:0x1e0000,Addr[5]:0xae0000,Addr[6
]:0xe60000
Start copy data from 0x201e0054 to 0x91000000 with sizeof 0x008f3040 .....................Done!
Start system with ram disk and set bootcmd to
BootArgs:noalign mem=50M console=ttyAMA0,115200 root=/dev/ram0 rootfstype=squashfs
mtdparts=hisilicon:0x40000(boot)ro,0x1000(flashcfg)ro,0x1f000(syspara)ro,0x180000(krnl)ro,0x8fffac@
0x1e0054(rootfs)ro,0x248fe0@0xc17020(minisystem)ro,0x180000(jffs2cfg),-(reserved) user_debug=0x1f
panic=1
U-boot Start from NORMAL Mode !
## Booting image at 20060054 ...
Image Name: Linux -2.6.21.7-hrt1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1456776 Bytes = 1.4 MB
Load Address: 90008000
Entry Point: 90008000
Loading Kernel Image ... OK
## Loading Ramdisk Image at 91000000 ...
Image Name: squashfs
Image Type: ARM Linux RAMDisk Image (uncompressed)
Data Size: 9383936 Bytes = 8.9 MB
Load Address: 00000000
Entry Point: 00000000
Starting kernel ...
Uncompressing Linux.......................... ...................................................... .......... done, booting the kernel.
Kernel Early-Debug on Level 0
iotable information:
virtual: 4093640704physical: 262144 length: 4096 type: 0
virtual: 4093706240physical: 26 2166 length: 04
virtual: 4076863488physical: 196608 length : 4096 type: 0
virtual: 4145303552physical: 90437 length: 4096/ type: 0
hisilicon_map_io 281 [arch/arm0/mach-core] .c]
hisilicon_init_irq 108 [arch/arm/mach-sd5113_v100_p01/core.c]
hisilicon_timer_init 228 [arch/arm/mach-sd5113_v100_p01/systimer.c]
hi_kernel_wdt_init 216 [arch/arm/mach-sd5113_v100_p01/hi_drv_wdt.c]
hisilicon_init_machine 175 [arch/arm/mach-sd5113_v100_p01/core.c]
hi_kernel_pci_preinit 390 [arch/arm/mach-sd5113_v100_p01/
is on clock
hi_kernel_pci_postinit 488 [arch/arm/mach-sd5113_v100_p01/hi_pci.c]
hi_kernel_pci_postinit on!
Linux version 2.6.21.7-hrt1 (root@vsut193167) (gcc version 4.1.2 (Wind River Linux Sourcery G++ 4.1-84)) #2
Wed Jul 31 16:31:00 CST 2013
CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv6TEJ), cr=00c5387f
Machine: SD5113-V100-PILOT-B01
Memory policy: ECC disabled, Data cache writeback
Get mem size 0x3200000;
CPU0: D VIPT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
Built 1 zonelists. Total pages: 12700
Kernel command line: noalign mem=50M console=ttyAMA0,115200 root=/dev/ram0 rootfstype=squashfs
mtdparts=hisilicon:0x40000(boot)ro,0x1000(flashcfg)ro,0x1f000(syspara)ro,0x180000(krnl)ro,0x8fffac@0x1e0054(rootfs)ro,
0x248fe0@0xc17020(minisystem)ro,0x180000(jffs2cfg),-(reserved) user_debug=0x1f panic=1
PID hash table entries: 256 (order: 8, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 50MB = 50MB total
Memory: 38508KB available (2636K code, 200K data, 108K init)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Hisilicon clock system V0.01
[clk_register, 244] AHBCLK
[clk_register, 244] ARMCORECLK
[ clk_register, 244] UARTCLK
PCI: bus0: Fast back to back transfers enabled
istatus and imask 16777216
istatus and imask 0
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
checking if image is initramfs. ..it isn't (bad gzip magic numbers); looks like an initrd
Freeing initrd memory: 9164K
Registering GDB sysrq handler
squashfs: version 3.4 (2008/08/26) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
JFFS2 version 2.2. (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: dw uart driver
dev:f2: ttyAMA0 at MMIO map 0x1614f000 mem 0xf714f000 (irq = 17) is a AMBA/DW
dev:f1: ttyAMA1 at MMIO map 0x1614e000 mem 0xf714e000 (irq = 16) is a AMBA/DW
RAMDISK driver initialized: 4 RAM disks of 23000K size 1024 blocksize
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max= 256) (6 bit encapsulation enabled).
CSLIP: code copyright 1989 Regents of the University of California.
SLIP linefill/keepalive option.
Start to set chip MaxBufWriteSize.
!Not find NUMONYX JS28F128M29EWHA chip.
hisilicon: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
hisilicon: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Hisilicon flash: registering whole flash at once as master MTD
8 cmdlinepart partitions found on MTD device hisilicon
Creating 8 MTD partitions on "hisilicon":
0x00000000-0x00040000 : "boot"
0x00040000-0x00041000 : "flashcfg"
0x00041000-0x000600 syspara"
0x00060000-0x001e0000 : "krnl"
0x001e0054-0x00ae0000 : "rootfs"
0x00c17020-0x00e60000 : "minisystem"
0x00e60000-0x00fe0000 : "jffs2cfg"
0x00fe0000-0x01000000 : "reserved"
usb clock is on!
h2v100-ehci h2v100-ehci.0: h2v100-ehci
h2v100-ehci h2v100-ehci.0: new USB bus registered, assigned bus number 1
h2v100-ehci h2v100-ehci.0 : irq 23, io mem 0x40010000
h2v100-ehci h2v100-ehci.0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1- 0:1.0: 2 ports detected
h2v100-ohci h2v100-ohci.0: h2v100-ohci
h2v100-ohci h2v100-ohci.0: new USB bus registered, assigned bus number 2
h2v100-ohci h2v100-ohci.0: irq 24, io mem 0x40020000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Netfilter messages via NETLINK v0.30.
ip_tables: (C) 2000-2006 Netfilter Core Team
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation < [email protected] >
RAMDISK: squashfs filesystem found at block 0, block number 9163
RAMDISK: Loading 9163KiB [1 disk] into ram disk... done.
VFS: Mounted root (squashfs filesystem) readonly.
Freeing init memory: 108K
-=# DOPRA LINUX 1.0 #=-
-=# EchoLife WAP 0.1 #=-
-=# Huawei Technologies Co., Ltd #=-
mount file system
Loading the kernel modules:
/etc/rc.d/rc.sysinit: line 37: sed: not found
Making device instances :
Setting console log message level:
Setting hostname:
Settingup the sysctl configurations:
Setting up interface lo:
Running local startup scripts.
************************* ********************
--== Welcome To EchoLife WAP ==--
--== Huawei Technologies Co., Ltd. ==--
***** ****************************************
WAP Ver:V100R005C00B010
WAP Timestamp:2013/07/31 16:42:59
********************************************
Mount the JFFS2 file system:
Start init EchoLife WAP process debug module ......
Start lunch kmsgread ...
Pid of kmsgrread is: 146
Set kmsgread process pid to:146;
Rootfs time stamp:2013-07-31_16:47:55
fuse init (API version 7.8)
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
User init start...
Loading the SD5113V100 modules:
ETH install success!
g_dp_GLB_reg_s->VERSION = 0x0, ui_version = 0x0, ui_spec_index = 1
SD511X DP V2.0 is installed !
SD511x MDIO ID V1.0 is installed
SD511x GPIO VERSION 1.0 is installed
SD511x GPIO_INT ID 1.0 is installed
SD511x I2C ID V1.0 is installed
SD511x TIMER ID V1.0 is installed
SD511X SPI ID v1.0 is installed
SD511X SYSCTL V1.0 is installed
SD511x UART ID V1.0 is installed
<6>
SD511X HW ID v1.0 is installed
SD511x EXT_INT ID 1.0 is installed
ifconfig eth0 hw ether 74:1E:93:06:1A:A8
Loading the EchoLife WAP modules: LDSP
SSP For LDSP Install Successfully...
HLP For LDSP Install Successfully...
CHIPADP-PHY For LDSP Install Successfully...
Get version through hardware!
CHIPADP-SD5113 For LDSP Install Successfully...
GPIO For LDSP Install Successfully...
HIGHWAY For LDSP Install Successfully...
I2C For LDSP Install Successfully...
MDIO For LDSP Install Successfully...
LSW For LDSP Install Successfully...
aui_receive[0] = ff aui_receive[1] = ff aui_receive[2] = ff aui_receive[3] = ff
DEV For LDSP Install Successfully...
CHIPADP-AR8316 LSW For LDSP Install Successfully...
TOPO hw_topo_init Successfully...
hw_topo_pdt_sep_eth_port_init ...
End hw_topo_wap_init...
TOPO PDT For SSMP Install Successfully...
Read Topo Info Product Des:EchoLife HG8240
Read MemInfo Des: 47844
SPI For LDSP Install Successfully...
UART For LDSP Install Successfully...
BATTERY For LDSP Install Successfully...
PLOAM For LDSP Install Successfully...
GMAC For LDSP Install Successfully...
KEY For LDSP Install Successfully...
LED For LDSP Install Successfully...
OPTIC For LDSP Install Successfully...
RF For LDSP Install Successfully...
le88226 For LDSP install successfully...
Loading BBSP L2 modules:
Common HLP For BBSP Install Successfully...
ont is not in Equip Mode:g_fw_equip=0
FLOW For BBSP Install Successfully...
VETH For LDSP Install Successfully...
hw_pkt_tunnel Install Successfully...
EMAC For LDSP Install Successfully...
MPCP For LDSP Install Successfully...
Loading DSP temporary modules:
linux kernel dopra is installed!
dsp sdk insmod success!
DSP For LDSP Install Successfully...
Loading BBSP L2_extended modules:
WIFI For BBSP Install Successfully...
ipv6 Install Successfully.. .
hw_dhcp Install Successfully...
hw_ethoam_kernel Install Successfully...
hw_pppoe Install Successfully...
hw_igmp_kernel Install Successfully...
mfw pkt per second: 80...
mfw Install Successfully...
hw_bind_init...
KARP Install Successfully...
Loading BBSP L3_basic modules:
nf_conntrack version 0.5.0 (400 buckets, 3200 max)
netdown replace to nf_ct_iterate_cleanup2
install success
Pktdump init Install Successfully...
ACl For BBSP Install Successfully...
Dosflt For BBSP Install Successfully...
Loading BBSP L3_extended modules:
napt register conntrack_handler
NAPT For BBSP Install Successfully...
_init_session SUCCESS
table_size =3040 hw_ker_ffwd_ipv4 install
hash_size = 760
ffwd register conntrack_handler
hw_ker_ffwd_core install
Portal For BBSP Install Successfully...
User device for bbsp Install Successfully...
NO ipv6!
NO hw_rout!
Configure Word : COMMON
COMMON:not BT mode
device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
CODEC For LDSP Install Successfully...
Start ldsp_user...0
<LDSP>HW_LdspCfg_XponProc start from gpon, uiUpMode=1.
<LDSP cfg>Set uiUpMode=1.
<LDSP>Hardware board id is 2 !
<LDSP>Hardware pcb id is 2 !
SD5113 test self OK
Lsw test self OK
Optic test self OK
PHY[1] test self OK
PHY[2] test self OK
PHY[3] test self OK
PHY[4] test self OK
PHY[5] test self NoCheck
PHY[6] test self NoCheck
FILE = /home/zhengjisheng/r1c01/sdk_optimize/sd511x_sdk/driver/src/./interface/i2c/hi_drv_i2c.c,
LINE = 151, FUNC = hi_kernel_i2c_burst_read_bytes
read data is over time
Optic calMode 0
GPON opened success !
ssmp bbsp igmp amp vspa omci
root.reserved: fe0000 20000
Start start pid=366; uiProcNum=6;
Start VSPA ...InitFrame amp; PID =370; state=0; 12.178;
InitFrame ssmp; PID=367; state=0; 12.558; InitFrame
amp; PID=370; in state=
0; 12.179;
omci; PID=371; in state=0; 12.743;
InitFrame omci; PID=371; out state=0; 12.744;
InitFrame igmp; PID=372; state=0; 12.805;
InitFrame igmp; PID=372; in state= 0; 12.806;
InitFrame ssmp; PID=367; in state=0; 12.559;
InitFrame amp; PID=370; out state=0; 13.085;
InitFrame igmp; PID=372; out state=0; 13.093;
PID USER VSZ STAT COMMAND
1 root 2132 S init
2 root 0 SWN [ksoftirqd/0]
3 root 0 SW [watchdog/0]
4 root 0 SW< [events/0]
5 root 0 SW< [khelper]
6 root 0 SW< [kthread]
28 root 0 SW< [kblockd/0]
31 root 0 SW< [khubd]
45 root 0 SW [pdflush]
46 root 0 SW [pdflush]
47 root 0 SW< [kswapd0]
48 root 0 SW< [aio/0]
VSPA pri from 0 to 10
InitFrame vspa_sip; PID=374; state=0; 13.283 ;
InitFrame vspa_sip; PID=374; in state=0; 13.284;
InitFrame vspa_sip; PID=374; out state=0; 13.285;
63 root 0 SW [mtdblockd]
110 root 2136 S /bin/sh /etc/rc.d/ rc.sysinit
140 root 0 SWN [jffs2_gcd_mtd7]
143 root 0 DW< [wap_lastword]
144 root 0 DW< [wap_ktrace]
146 root 1960 S kmsgread
150 root 2136 S /bin/sh /etc/rc.d/rc.start/ 1.sdk_init.sh start
283 root 0 SW [mpcp]
288 root 0 SW< [kTimerTask]
335 root 0 SW [cpucar]
364 root 10752 S hw_ldsp_user
366 root 2012 S start ssmp bbsp igmp amp vspa omci
367 root 4036 S ssmp
369 root 5012 R bbsp
370 root 3764 R amp
371 root 5468 R omci
372 root 4028 R igmp
374 root 8736 RN vspa_sip
376 root 2136 S /bin/sh /etc/rc.d/rc.start/1.sdk_init.sh start
379 root 2000 S sleep 30
380 root 2136 S /bin/sh /etc/rc.d/rc.start/ 1.sdk_init.sh start
384 root 2136 S /bin/ sh /etc/rc.d/rc.start/1.sdk_init.sh start
386 root 2308 R ps
392 root 2132 R sh -c rm -f /mnt/jffs2/customize_upgrade.tar.gz
393 root 0 Z [rm]
telnet: can't connect to remote host (127.0. 0.1): Connection refused
InitFrame bbsp; PID=369; state=0; 13.791;
InitFrame bbsp; PID=369; in state=0; 13.792;
InitFrame bbsp; PID=369; out state=0; 13.795;
telnet: can' t connect to remote host (127.0.0.1): Connection refused
[HW_XML_IsXmlEncrypted] iFileDescryption::0x1
[HW_XML_DBCheckXMLValid] file is encrypt !
Start HW_DM_PDT_Init....
[DEV]HW_DM_GetBoardInfo failed.uiRet = 0xf7205405
Init dm data err, uiRet = 0xf72054
Init DM Error! Return=0xf7205405;
Deinit SMP Successfully!
SSMP init ManageModule ..................... [Err:0xf7205405]
ssmp InitFrame Err[f7205405],err state = 0
Get signal:0 backtrace ...
/lib/libhw_ssp_basic.so(HW_OS_SignalTrapUser1+0x2c) [0x40065eb0]
[0xbe9e2c54]
SSMP HW_Init_Frame error. uiReturn=-148876283;
telnet: can't connect to remote host (127.0.0.1) : Connection refused
Start ProcMonitor with sip ...
telnet: can't connect to remote host (127.0.0.1): Connection refused
<6>br0: topology change detected, propagating
br0: port 1( eth0) entering forwarding state
[ProcMonitor]: Init Error! Return=0xf7104012;
Dropped the page cache.
telnet: can't connect to remote host ( 127.0.0.1): Connection refused
telnet: can't connect to remote host (127.0.0.1):Connection refused
Init WEB Message Error! Return=0xf7104012;
Web server init failed, uiRet = 0xf7104012.
g_uiWebInitFlag: estroy GmemList!
Init APM Message Error! Return=0xf7104012;
APM HW_Init_Frame error. uiReturn=0xf7104012;
HW_APM_FreeRes::HW_OS_GmemList!
HW_APM_FreeRes SUCCESS!
telnet: can't connect to remote host (127.0.0.1 ): Connection refused
telnet: can't connect to remote host (127.0. 0.1): Connection refused
telnet: can't connect to remote host (127.0 .0.1): Connection refused
HW_MU_FreeRes: estroy GmemList!
Init MU Message Error! Return=0xf7104012;
Init TimeOut, Line: 181
Init TimeOut, Line:181
Init TimeOut , Line: 181
Init TimeOut, Line : 181
telnet: can't connecttelnet: can't connect to remote host ( 127.0.0.1): Connection refused
to remote host (127.0.0.1): Connection refused
telnet: ctelnet: can't connect to remote host (127.0.0.1): Connection refused
telnet: can't connect to remote host (127.0.0.1 ): Connection refused

Enshan Wireless Forum: (Print This Page)

Uploaded by

Copyright:

Available Formats

Enshan Wireless Forum: (Print This Page)

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Enshan Wireless Forum: (Print This Page)

Uploaded by

Copyright:

Available Formats

Enshan Wireless Forum

Author: dd1kaTime : 2016-1-8 00:57Title

1. U-Boot 1.1.4 (Jun 21 2012 - 13:51:21)

1. Press d key to abort autoboot: 10

After entering help, the following commands can be executed:

You can also see the relevant configuration by entering printenv

Author: Routing Destroyer Time: 2016-1-8 12:11

Author: dd1kaTime : 2016-1-8 12:16

Quote: Routing Destroyer Posted at 2016-1-8 12:11

Author: palmy888 Time: 2016-1-11 21:32

You might also like