Structural Engineering Drawings

STRUCTURAL ENGINEERING DRAWINGS
NOTES / COMMENTS :
GENERAL NOTES:
L K I H G F E D C B A A
NOTES : 1. READ THE DRAWINGS IN CONJUNCTION WITH ALL RELEVANT
SPECIFICATIONS, AND SERVICE DRAWINGS. ANY UNCERTAINTIES IN
· DPC TUCKED INTO BED JOINT THE SPECIFICATIONS OR ON DRAWINGS MUST BE REPORTED TO THE
280 ENGINEER AS SOON AS POSSIBLE. ANY DISCREPANCIES BETWEEN THE
4515 6590 2515 6390 5230 9860 1875 4515 1915 4630
· OPEN PERPED JOINTS AT 660mm SPECIFICATIONS AND THE DRAWING MUST BE REPORTED TO THE
50mm CAVITY MAX CENTERS. ENGINEER.
2. NO DEVIATION FROM THE DETAILS ON THE DRAWING WILL

BE ALLOWED WITHOUT THE WRITTEN CONSENT OF
A THE ENGINEER.
---
DPC
SCHEDULE OF AREAS : SEE ISOLATION
JOINT DETAIL OPEN PERPEND JOINTS @ 3. THESE DRAWINGS MAY NOT BE COPIED OR RE-USED
2
TOTAL AREA OF TRENCHES 587.60 m 660mm CENTERS MAX. WITHOUT THE WRITTEN CONSENT OF THE ENGINEER.
1100 x 300 - R.C Footing ________________________________________________________
1
85
4. IN GENERAL, CONCRETE (STRUCTURAL) SHALL COMPLY WITH SABS
1655
150
BLINDING CALCULATION : 2% Slope 1200-1982.
FINISHED PLATFORM LVL
Approved compacted in layers n.e 150mm

A CONCRETE : AREA ( 587.6 m2 ) x DEPTH (0.050m) = 29.38 m3
EXCAVATION DEPTH
---
2 1000 x 300 - R.C Footing 5. CONCRETE CLASS:
Min. 3 Layers of G5 Material or Similar

15Mpa Blinding Layer ( Inclusive of 10 % Waistage ) = 32 m3 BLINDING LAYER - CLASS C 15/19
VARIES
TO 95% MOD AASHTO
600 x 300 - R.C Footing ________________________________________________________ STRIP FOOTINGS (BRICKWALLS) - CLASS F 25/19
3700
TRENCHES - CLASS F 25/19

STRIP FOOTING CALCULATION : 25Mpa APRON SLAB WITH MESH
REF. 193 PLACED IN CENTER 6. SURFACE FINISHES:

CONCRETE : AREA ( 588 m2 ) x DEPTH (0.300m) = 176.28 m3
DEPTH
FORMED SURFACES:
300
3 15Mpa Blinding Layer ( Inclusive of 10 % Waistage ) = 194.00 m3 FOUNDING DEPTH TO BE DETERMINED UNEXPOSED SURFACES - ROUGH.
TO 95% MOD AASHTO

600 x 300 - R.C Footing ________________________________________________________ BY THE ENGINEER ON SITE EXPOSED SURFACES - SMOOTH.
UNFORMED SURFACES:
1000 x 300 - R.C Footing

TOP OF WALLS - STEEL TROWELLED.
3160
Blinding
50mm
FLOORS OF TRENCHES - WOOD FLOATED.
475 525

ENTRANCE RAMPS, - WOOD FLOATED.
4 600 x 300 - R.C Footing 600 x 300 - R.C Footing
1000 ALL EXPOSED SHARP CORNERS SHALL BE CHAMFERED AS FOLLOWS:
3.795 x 3.52 x 0.3m Pad Footing with WIDTH OF FOOTING
1.0 x 0.8 x 0.8m High R.C Stub Column
ALL CORNERS (EXCEPT WHERE OTHERWISE SHOWN) 25x25mm.
SECTION B - B ( 280mm CAVITY WALL )

4270
7. 50mm BLINDING LAYER UNDER ALL FOUNDATIONS.

SCALE 1 : 20
8. CONCRETE COVER TO REINFORCEMENT:
FOUNDATIONS - 50mm
5 9. ALL FOUNDATION EXCAVATIONS MUST BE INSPECTED AND APPROVED
BY THE ENGINEER BEFORE PLACING OF REINFORCEMENT OR CASTING

1730
OF CONCRETE. IF THE FOUNDING LEVEL AS PER DRAWING IS NOT

600 x 300 - R.C Footing SUITABLE, FURTHER EXCAVATIONS SHALL BE DONE TO A DEPTH AS
6 1000 x 300 - R.C Footing DETERMINED BY THE ENGINEER ON SITE. THE ENGINEER MAY


INSTRUCT THAT CERTAIN EXCAVATIONS BE BACKFILLED WITH MASS
1 CONCRETE TO REQUIRED LEVEL. (CLASS AS PER ITEM5 ABOVE).
NOTES :
10.LAP AND ANCHORAGE LENGTH 50 x DIAMETER OF REINFORCEMENT.
4500
· DPC TUCKED INTO BED JOINT

C C B B 345 11. AFTER PLACING, ALL REINFORCEMENT MUST BE CHECKED AND
--- --- --- ---
· OPEN PERPED JOINTS AT 660mm APPROVED BY THE ENGINEER ON SITE BEFORE CASTING OF CONCRETE.
MAX CENTERS. 115mm CAVITY
12.NO HOLES OR NOTCHES SHALL BE CUT, CHIPPED OR FORMED IN
600 x 300 - R.C Footing CONCRETE UNLESS APPROVED BY THE ENGINEER.
7 800 x 300 - R.C Footing
13.DURING COLD OR WET WEATHER CONCRETE MUST BE
2030
800 x 300 - R.C Footing DPC

HANDLED IN ACCORDANCE WITH SPECIFICATIONS.

SEE ISOLATION
OPEN PERPEND JOINTS @
JOINT DETAIL
660mm CENTERS MAX. 14.REMOVAL OF SHUTTERING TO BE DONE IN ACCORDANCE WITH
8 1430 x 300 800 x 300 - R.C Footing 800 x 300 - R.C Footing 1430 x 300
SPECIFICATIONS.
600 x 300 - Footing
600 x 300 - Footing

R.C Footing R.C Footing
150 85
2% Slope 15.LOADINGS ON CONCRETE FIRST FLOOR SLABS MAXIMUM
FINISHED PLATFORM LVL 100kg/m².
3850
EXCAVATION DEPTH
16.LOADING:
VARIES
PERMISSIBLE BEARING PRESSURE:

9 800 x 300 - R.C Footing 1000 x 300 - R.C Footing 600 x 300 - R.C Footing

25Mpa APRON SLAB WITH MESH COLUMN BASES - 150Kpa
Approved compacted in layers n.e 150mm REF. 193 PLACED IN CENTER
NOMINAL IMPOSED FLOOR LOADS:
TO 95% MOD AASHTO
DEPTH
TO 95% MOD AASHTO
300
FOUNDING DEPTH TO BE DETERMINED ROOF SLABS - 1.5KN/m²
BY THE ENGINEER ON SITE
5550
800 x 300 - R.C Footing 600 x 300 - R.C Footing 17.FOUNDING DEPTH :
Blinding
50mm
ALL EXCAVATION DEPTHS TO BE AT A PROVISIONAL DEPTH OF 1.275m
610 490 BELOW FINISHED PLATFORM LEVEL.
WHERE CONDITIONS ARE NOT SUITED FOR A NORMAL RAFT AN

1100 ALLOWANCE FOR IMPORTING OF SUITABLE MATERIAL TO BE PROVIDED
10 800 x 300 - R.C Footing 600 x 300 - R.C Footing WIDTH OF FOOTING AT A DEPTH OF 450mm ( 3 LAYERS 150mm) BELOW FOOTINGS AND
COMPACTED TO 97% MOD ASSHTO FOR MODIFIED STRIP FOOTING.
SECTION A - A ( 345mm CAVITY WALL ) 18.BACKFILL:

3880
SCALE 1 : 20
D SELECTED FILL BENEATH SURFACE BEDS TO BE SELECTED GRANULAR
---
600 x 300 - R.C Footing MATERIAL COMPACTED IN 150mm LAYERS TO 95% MOD. AASHTO
DENSITY. FOUNDING LEVEL TO BE CONFIRMED BY THE ENGINEER.


TO 95% MOD AASHTO
2115
1.4 x 1.4 X 0.3m

R.C Pad Footing 800 x 300 - R.C Footing
MODIFIED FOOTINGS NOTES
N D
· WHERE COLLAPSIBLE SOILS EXIST, A PROVISION OF IMPORTED DESIGN CONSULTANT :
---
1.4 x 1.4 X 0.3m MATERIAL TO BE ALLOWED FOR, TO INCLUDE TESTING OF EACH LAYER
-0.000
TO ENSURE THE REQUIRED MOD IS ACHIEVED.
4605
R.C Pad Footing F. P. L

· FOR ALL EXCAVATIONS RESULTING IN DEPTHS EXCEEDING 1.5m, AN
E ALLOWANCE FOR SHORING TO BE MADE AS WELL AS STRICT SAFETY
---
MEASURES TO BE CARRIED OUT WITH THE APPROVAL OF THE

HEALTH AND SAFETY PROFESSIONAL.
1150
13 1000 x 300 - R.C Footing 3.115 x 1.68 X 0.3m BUSINESS ADDRESS : CONTACT DETAILS :
· ALL LATERAL SUPPORT DESIGNS TO BE SUBMITTED TO THE
BLINDING
R.C Pad Footing
ENGINEER FOR APPROVAL PRIOR TO ESTABLISHING ON SITE. Office 1B Deodant Building Tel : (031) 701 1038
50mm
3135
1.4 x 1.4 X 0.3m 10 Payne Street, Tel : (031) 701 1038

R.C Pad Footing - 0.760
- 0.810
FOUNDING LEVEL
TOP OF FORMATION
Pinetown, E-mail : [email protected]
3600 Website : www.vumesa.co.za
14 1000 x 300 - R.C Footing
MIN
450
- 1.260
1.6 x 1.4 X 0.3m 1.4 x 1.4 X 0.3m BOTTOM G7 LAYER FOR DESIGN CONSULTANT
COURSE - MAX. 425

R.C Pad Footing E R.C Pad Footing
---
Footing Depth + 600 FUNCTION NAME SIGNATURE
MULTIPLES OF
500
DESIGNED BY T. HLATSHWAYO
BRICK
G5 MATERIAL COMPACTED TO 95% MOD AASHTO IN LAYERS N. E 150
mm.FINAL DEPTH TO BE DETERMINED BY COLLAPSIBLE LAYER THICKNESS. DRAWN BY T. HLATSHWAYO
DESIGN CHECKED BY N. A MBATHA
TYPICAL MODIFIED FOOTING SECTION 10mm
I.J DRAWING CHECKED BY N. A MBATHA
SCALE 1 : 25
FOUNDATION LAYOUT PLAN APPROVAL CONSULTANT
300
SCALE 1 : 100 NAME : N.A MBATHA SIGNATURE
DATE : 31 / 01 / 2020 PR. ENG.NO. 201470322
300
COURSE - MAX. 425

MULTIPLES OF
CONCRETE
STRIP FOOTING
BRICK
f:\sntdp projects\77. vumesa projects\current projects\04 - tshilwavhusiku site\sntdp_77_p4_working drawing.dwg

13 14 11 12 TYPICAL STEP DETAIL
G
SCALE 1 : 25 A ISSUED FOR INFORMATION 31/01/2020 T. H
REV NO. DESCRIPTION : DATE DRAWN
2 LAYERS OF IN-SITU MATERIAL TO BE
RIPPED AND RE-COMPACTED PROJECT DESCRIPTION
25Mpa SURFACE BED 25Mpa SURFACE BED TO 93% MOD AASHTO
300 Ø R.C COLUMN WITH 110Ø SW LIMPOMPO DEPARTMENT OF SOICIAL
OUTLET PIPE FROM FULL BORE R.C APRON AROUND 85mm STEP
150
150
85mm STEP DRAINAGE FROM THE FOOR SLAB BUILDING

150mm STEP DEVELOPMENT
150mm STEP
2% Slope
2% Slope FINISHED PLATFORM LVL
TSHILWAVHUSIKU CLINIC
150
150
NEW MULTI PURPOSE OFFICE BLOCK

2 LAYERS OF IN-SITU MATERIAL TO 25Mpa APRON SLAB WITH MESH
2 LAYERS OF IN-SITU MATERIAL 2 LAYERS OF IN-SITU BE RIPPED AND RE-COMPACTED REF. 193 PLACED IN CENTER DRAWING TITLE :
TO BE RIPPED AND RE-COMPACTED TO 93% MOD AASHTO
TO 95% MOD AASHTO
MATERIAL TO BE RIPPED
ALL FOUNDATION BRICKWORK TO RECEIVE AND RE-COMPACTED STORM WATER SIDES OF TRENCHES TO BE
BRICKFORCE IN EVERY LAYER WITH IN-SITU CATCHPIT BACKFILLED WITH IN-SITU
TO 93% MOD AASHTO MATERIAL
MATERIAL BACKFILLED TO SIDES OF TRENCHES.
FOUNDATION LAYOUT PLAN AND CROSS
SECTIONS SHOWING CONSTRUCTION
300
300
FOUNDING DEPTH TO BE DETERMINED DETAILS
300
300
FOUNDING DEPTH TO BE DETERMINED FOUNDING DEPTH TO BE DETERMINED BY THE ENGINEER ON SITE

BY THE ENGINEER ON SITE BY THE ENGINEER ON SITE
BLINDING
BLINDING
25Mpa CONCRETE 400 400 400 400 25Mpa CONCRETE
50mm
50mm
ALL DIMENSIONS TO BE CHECKED ON SITE PRIOR
BLINDING
25Mpa CONCRETE 25Mpa CONCRETE FOOTING FOOTING

525 475 900 500
50mm
TO THE COMMENCEMENT OF ANY WORK. PROJECT NUMBER CONTRACT NUMBER :

500 500 FOOTING FOOTING ANY DISCREPANCIES TO BE REPORTED TO THE
800 800 VUM_77_12/19_001 TEC05/2018
AUTHOR IMMEDIATELY.
1000 1400 DRAWING STATUS : SCALE SIZE
1000 Pad Footing THIS DRAWING IS TO BE READ IN
CONJUNCTION WITH ALL ARCHITECTURAL AND FOR INFORMATION AS SHOWN A1
STRUCTURAL DRAWINGS.
ISSUED DATE : DRAWING No. No. OFF REV
SECTION C - C SECTION B - B SECTION B - B 31-01-2020 P4 - 01 -100 1 of 1 A
SCALE 1 : 25 SCALE 1 : 25 SCALE 1 : 25
C Copyright reserved - Vumesa (Pty) Ltd

NOTES / COMMENTS :
GENERAL NOTES
STRUCTURAL STEEL NOTES: 1. ALL LEVELS AND DIMENSIONS TO BE CHECKED ONSITE.
NOTE :
6 No. 22mm Ø HOLES 2. THIS DRAWING TO BE READ IN CONJUNCTION WITH
8Y16-70a-200 B1
1. Steelwork:
8Y12-71a-200 T1
FOR M20 ANCHOR BOLTS
THE ARCHITECTURAL DRAWINGS.
254 x 146 x 31 I-SECTION PF
FACTORY WELDED TO BASE 1.1. Structural steel to be Grade 300WA to SABS 1431-2005. Steel to
PLATE 600 3. ALL CONCRETE WORK TO COMPLY WITH SABS 1200G.
A be free of laminations.
---
125x75x8 L CLEAT 150x75x20x2 CFLC COLUMN B : 203 x 133 x 25 mm S.H.S WITH
6mm FACTORY fw FIXING COLUMN TO 10mm 1.2. Fabrication of structural steelwork to be in accordance with BS
WELDED TO RAFTER WITH 4M16 G 4.8 BOLTS 110 190 190 110 4. CONCRETE CLASS :-
FIXED TO CLEAT END PLATE AND 16mm BASE PLATE WITH 5400-1980 Part 6
6 x 18 Ø HOLES FOR M16 SITE CONNECTION 1.3. All holes shall be drilled or punched. STRIP FOOTINGS & BASES = 25 MPa
COLUMN - A AND 6 x 22 Ø HOLES FOR M20
1.4. Plates shall be sawn or machine flame cut. RETAINING WALLS = 25 MPa
70a ANCHOR BOLTS
1.5. Shop-detail drawings shall be approved by the Engineer before SURFACE BEDS = 25 MPa
71b
fabrication commences.
60
BLINDING = 10 MPa
8Y12-71b-200 T2
1.6. After fabrication the nose shall be erected at the fabrication site.
Components shall then be suitably marked to facilitate re-erection 5. COVER TO REINFORCEMENT :-
71a END PLATE DETAIL 2 :
COLUMN - A : 203 x 133 x 25 mm WITH on site. No steps will be permitted in the bottom flange sliding STRIP FOOTINGS & BASES = 50 mm
400
280
300 x 200 x 12mm THICK END
70b
8Y16-70b-200 B2 PLATE WITH 6 x 18Ø HOLES FOR 6mm FACTORY fw FIXING COLUMN surface. SLABS - on the ground - Bot. = 50 mm
END PLATE DETAIL 2 : TO 10mm END PLATE WITH
M16 BOLT AND NUT-SET. 1.7. Fabrication and Assembly: In accordance with clause 6803 (J) of SLABS - on the ground - Top = 25 mm
300 x 200 x 12mm THICK END 6 x 18mm Ø HOLES. STEEL MEMBER
PLATE WITH 6 x 18Ø HOLES FOR TO RECEIVE A 6mm SITE WELD ONTO the standard specifications. MASONRY REINF. CONCRETE RETAINING WALLS - earth face = 25 mm
60
M16 BOLT AND NUT-SET. 16mm BASE PLATE. 1.7.1. Position: Transverse position at deck connection ± 10mm COLUMNS = 30 mm
1.7.2. Alignment: Deviation of center line of bottom flange from
A specified line ± 3mm OVER 12m with MAXIMUM 5mm deviation 6. ALL FOUNDATION EXCAVATIONS TO BE INSPECTED BY THE ENGINEER
---
1.7.3. Surface Regularity: Surface regularity of sliding surface = 1mm PRIOR TO CASTING OF CONCRETE.
16mm BASE
PLATE OVER 1m
1.7.4. Slope: Slope in both directions on the sliding surface = ± 0,1% 7. ALL REINFORCING FIXING TO BE INSPECTED BY THE ENGINEER PRIOR
PAD COLUMN REINFORCEMENT LAYOUT PLAN TO CASTING OF CONCRETE.
( SHOWING COLUMNS C1, C2, C4 & C5 ) 2. Connections:
SCALE 1 : 25 COLUMN C8 & C9 : 350 x 350 x 16mm BASE PLATE 8. SIX CUBES TO BE TAKEN PER POUR.
SCALE 1 : 10
THREE TO BE TESTED AT SEVEN DAYS, THE REMAINDER AT TWENTY
2.1. Welded connection:
EIGHT DAYS. THE RESULTS TO BE FORWARDED TO THE ENGINEER.
2.1.1. All welding shall be in accordance with SABS 044-1983 or latest
revised. Manufacturer is to submit welding procedure and
9. CONTRACTOR TO CONSTRUCT A BLINDING LAYER IF SOIL CONDITIONS
welders qualification report
203 x 133 x 25 I-SECTION PF 203 x 133 x 25 I-SECTION PF RESULT IN REINFORCEMENT COVER NOT BEING MAINTAINED.
2.1.2. All butt welds in web and flange plates shall be full penetration
SITE WELDED TO BASE PLATE SITE WELDED TO BASE PLATE
V-notch butt welds.
10. ALL STRUCTURAL CONCRETE TO BE CURED FOR A MINIMUM OF FIVE
2.1.3. All other welds shall be continuous fillet welds. Minimum fillet
DAYS.
weld sizes shall be as follows:
11. BRICKWORK SHOWN HATCHED ARE LOAD BEARING. ALL LOAD BEARING
Thickness of thicker part: Weld Size:
BRICKWORK TO BE 14MPa NFX. TOP OF ALL BRICKWORK TO RECEIVE 2
LAYERS OF 3 PLY MALTHOID ON SMOOTH RENDERED SURFACE.
-up to 12mm 5mm
-over 12mm up to 20mm 6mm
12. ALL CONCRETE PLASTER AND BRICKWORK PLASTER INTER-FACES TO
RECEIVE V-JOINTS.
20° - except that the weld size does not have to exceed the 13. THE ENGINEER REQUIRES 48HRS NOTICE FOR ALL INSPECTIONS.
thickness of the thinner part.
14. ALL WORKS TO BE IN ACCORDANCE WITH SANS 1200
2.2. Bolted connections:
425 x 230 2.2.1. Bolted connections shall be made using high strength friction grip
T.O.C : + 0.085 170mm R.C SLAB R.C Upstand Grade 8.8 and 4.8 bolts. Bolts shall be used and installed in
°
80
525 x 145 x 10mm accordance with SABS 094-1982 (turn of the nut method) A
THICK END PLATE maximum of one re-use only of HSFG bolts will be permitted.
3 Ply Malthoid 2.2.2. Faying surfaces shall be blast cleaned to ensure a minimum
Y10-75b Slip Joint friction coefficient of 0.5 and shall be free of all deleterious
STIRRUP material.
350 x 350 x 16mm
BASE PLATE
3. Painting:
8Y16-76-200 EF
3.1. The underside of the bottom flanges (the sliding surfaces) shall
not be painted.
COLUMN - C9 ELEVATION 3.2. The remainder of the nose (with the exception of areas referred to
SCALE 1 : 25 300
in 2.2.2 and 3.1 above) shall be painted with one coat of
60 90 90 60 zinc-chromate primer followed by one coat of undercoat as a
50
Y10-75a minimum acceptable specification.
STIRRUP 203 x 133 x 25 I-SECTION PF 203 x 133 x 25 I-SECTION PF
SITE WELDED TO BASE PLATE FACTORY WELDED TO BASE PLATE
COLUMN - A : 203 x 133 x 25 mm
200
100
POCKET TO BE FILLED 525 x 145 x 10mm
CONSTRUCTION 25Mpa CONCRETE
WITH 6mm FACTORY fw FIXING
THICK END PLATE
JOINT COLUMN TO 10mm END PLATE
T.O.C : + 0.170
WITH 6 x 18mm Ø HOLES FOR
RAFTER FIXING DETAIL 1
50
81b
5Y12-91b-200
STIRRUPS
3Y20-80-200 3Y2080-200
SIDE SIDE 12mm END
PLATE
90
5Y20-80-200 EF
72
T.O.C : + 0.170 COLUMN C7 END PLATE DETAIL 2 :
T.O.C : + 0.085 2Y12-81a-200 300 x 200 x 12mm END PLATE ( 2 No. Of )
LOCATING STIRRUPS SCALE 1 : 10
--- ---
Y10-75a B B
5Y12-91b-200
STIRRUP
STIRRUPS
REINFORCEMENT OF STUB COLUMN SUPPORT FOR C7

220 x 220 x 6.0 SCALE 1 : 25
8Y16-76-200 EF S.H.S
T.O.C : + 0.170
8Y12-71a-200 T1 T.O.C : + 0.085 DESIGN CONSULTANT :
3Y20-90-200 EF
2Y20-90-200 SIDE
8Y16-70a-200 B1 72 72 91b
8Y12-71a-200 T1
8Y16-70b-200 B2 BUSINESS ADDRESS : CONTACT DETAILS :
8Y12-71b-200 T2
Y10-74 72 72
STIRRUP 8Y16-70a-200 B1 Office 1B Deodant Building Tel : (031) 701 1038
8Y16-70b-200 B2 ALL DIMENSIONS TO BE CHECKED ON SITE PRIOR
10 Payne Street, Tel : (031) 701 1038
8Y12-71b-200 T2 TO THE COMMENCEMENT OF ANY WORK.
2Y12-91a Pinetown, E-mail : [email protected]
SECTION A - A STIRRUP ANY DISCREPANCIES TO BE REPORTED TO THE
( THROUGHT COLUMNS C1, C2, C4 & C5 ) AUTHOR IMMEDIATELY. 3600 Website : www.vumesa.co.za
SCALE 1 : 25 THIS DRAWING IS TO BE READ IN
REINFORCEMENT OF STUB COLUMN SUPPORT FOR C9 CONJUNCTION WITH ALL ARCHITECTURAL AND FOR DESIGN CONSULTANT
SCALE 1 : 25
STRUCTURAL DRAWINGS. FUNCTION NAME SIGNATURE
DRAWN BY T. HLATSHWAYO
DESIGN CHECKED BY N. A MBATHA
DRAWING CHECKED BY N. A MBATHA
APPROVAL CONSULTANT
NAME : N.A MBATHA SIGNATURE
270 M20 BOLT
DATE : 31/ 01 / 2020 PR. ENG.NO. 201470322
LEVELING
M20 BOLT GROUT
LEVELING BASE PLATE
7.5 Ø POCKET
GROUT
150 mm
7.5 Ø POCKET
NOTE :

150 mm
4 No. 22mm Ø HOLES
300
FOR M20 ANCHOR BOLTS
A ISSUED FOR INFORMATION 31/01/2020 T. H
20 REV NO. DESCRIPTION : DATE DRAWN
CONCRETE & REINFORCING
320
--- --- 60
NOTES: PROJECT DESCRIPTION
350 B B 20 20 6mm FILLET
1. ALL EXPOSED EDGES TO BE CHAMFERED 20x20

LIMPOMPO DEPARTMENT OF SOICIAL
60 60
5Y12-86b-200
6mm FILLET
40 270 40
DEVELOPMENT
STIRRUPS
220 x 220 x 6 UNLESS OTHERWISE NOTED

S.H.S 6mm FILLET
20
2. MIN. CONCRETE COVER TO REINFORCEMENT = 30 mm
T.O.C : + 0.255
T.O.C : + 0.170
TSHILWAVHUSIKU CLINIC
20
90x90x20mm THICK 3. MINIMUM LAP LENGTH = 45 x DIA. OF BAR
30
40 SECTION WASHER PLATE
225 x 225 x 4.5 mm

WITH Ø22mm HOLE 4. ABBREVIATIONS USED : NEW MULTI PURPOSE OFFICE BLOCK
3Y20-85-200 EF 350x90x20mm THICK
30
T - TOP
S.H.S WITH 6mm FW 2Y20-85-200 SIDE SECTION WASHER PLATE
270
350
B - BOTTOM
ALL ROUND WITH Ø22mm HOLE
45
86b CTS - CENTRES
DRAWING TITLE :
90
MJ - MOVEMENT JOINT
45
CJ - CONTRACTION JOINT
45
40 EF - EACH FACE
90
ABR - ALTERNATE BARS REVERSED

OFFICE BLOCK FOUNDATION
45
45 45
12mm BASE 5. NOTATION FOR CALLING UP BARS :
PLATE 5 Y12 - 264 - 200 EF
90
40 270 40 POSITION
SUB-STRUCTURE, COLUMN
2Y12-86a
STIRRUP 350
SPACING
AND REINFORCEMENT DETAILS
COLUMN C8 & C9 : 350 x 350 x 12mm BASE PLATE NO OF BARS
BAR MARK
SCALE 1 : 10 HOLDING DOWN BOLT DETAIL SHOWING
REINFORCEMENT OF STUB COLUMN SUPPORT FOR C8 SINGLE BOLT DETAIL BAR TYPE & DIA.
SCALE 1 : 25 HOLDING DOWN BOLT DETAIL SHOWING PROJECT NUMBER CONTRACT NUMBER :
SCALE 1 : 5 6. ALL EXPOSED FORMED FACES TO RECEIVE : VUM_77_12/19_001
DOUBLE BOLT DETAIL TEC05/2018
SCALE 1 : 5 SMOOTH F2 FINISH DRAWING STATUS : SCALE SIZE
ALL EXPOSED UNFORMED FACES TO RECEIVE :
SMOOTH STEEL FOR INFORMATION AS SHOWN A1
FLOATED FINISH. ISSUED DATE : DRAWING No. No. OFF REV
31-01-2020 P4 - 01 - 120 1 of 1 A

NOTES / COMMENTS :
COLUMN SCHEDULE GENERAL NOTES:
COLUMN TYPE COLUMN SIZE NUMBER OFF COLUMN TYPE 1. READ THE DRAWINGS IN CONJUNCTION WITH ALL RELEVANT
L K I H G F E D C B A 'C1 - C6 ' 440x440mm 6 REINFORCED CONCRETE COLUMN SPECIFICATIONS, AND SERVICE DRAWINGS. ANY UNCERTAINTIES IN
THE SPECIFICATIONS OR ON DRAWINGS MUST BE REPORTED TO THE
'C7' 1500x1000mm 1 REINFORCED STUB COLUMN ENGINEER AS SOON AS POSSIBLE. ANY DISCREPANCIES BETWEEN THE
220x200x6mm 1 SQUARE HOLLOW SECTION - SHS SPECIFICATIONS AND THE DRAWING MUST BE REPORTED TO THE
'C8'
4515 6590 2515 6390 5230 9860 1875 4515 1915 4630 ENGINEER.
' C9' 220x220x6mm 1 SQUARE HOLLOW SECTION - SHS
2. NO DEVIATION FROM THE DETAILS ON THE DRAWING WILL
BE ALLOWED WITHOUT THE WRITTEN CONSENT OF
THE ENGINEER.
A 3. THESE DRAWINGS MAY NOT BE COPIED OR RE-USED
---
WITHOUT THE WRITTEN CONSENT OF THE ENGINEER.
.J
C. J
C
C
.J
.J
.J
C
I. J I. J SURFACE BED LEGEND I. J 4. IN GENERAL, CONCRETE (STRUCTURAL) SHALL COMPLY WITH SABS
1 SYMBOL TAG DESCRIPTION
1200-1982.
I. J I. J
1655
C
.J
C
.J
5. CONCRETE CLASS:
.J
I. J ISOLATION JOINT .J
C
I. J
I. J
I. J I. J
I.J
I.J
A S.C.J SAW CUT JOINT
2 --- BLINDING LAYER - CLASS C 15/19
I. J C.J CONSTRUCTION JOINT I. J STRIP FOOTINGS (BRICKWALLS) - CLASS F 25/19
I. J
MASONRY NOTES: TOTAL WIDTH
TRENCHES - CLASS F 25/19
I.J
C. J
I. J
3700
I. J CAVITY 6. SURFACE FINISHES:
I. J
I. J
85mm
STEP
BRICK FORCE AT VERTICAL CENTRES NOT EXCEEDING
425mm IN ALL SUPERSTRUCTURE WALLS WITH FORMED SURFACES:
I. J
I. J
I.J
I.J
C. J UNEXPOSED SURFACES - ROUGH.
C. J C. J ADDITIONAL LAYERS AS FOLLOWS :
I. J EXPOSED SURFACES - SMOOTH.
3 C. J UNFORMED SURFACES:
I. J C. J · IN EVERY COURSE IN ALL FOUNDATION MASONARY. TOP OF WALLS - STEEL TROWELLED.
I. J FLOORS OF TRENCHES - WOOD FLOATED.
MESH REF. 245 - T. O. C : + 0.255mm
MESH REF. 245 - T. O. C : + 0.255mm

125mm THICK SURFACE BED WITH
5 Courses
I. J
3160
· IN TWO COURSES IMMEDIATELY ABOVE FLOOR
425mm
Detail A
I.J
I.J
ENTRANCE RAMPS, - WOOD FLOATED.
I.J
I. J
I. J
I.J
I.J
MESH REF. 245 - T. O. C : + 0.255mm
SLAB.
MESH REF. 245 - T. O. C : + 0.255mm
Detail A ALL EXPOSED SHARP CORNERS SHALL BE CHAMFERED AS FOLLOWS:

· IN TWO COURSES IMMEDIATELY BELOW WINDOWS
4 I. J I. J
ALL CORNERS (EXCEPT WHERE OTHERWISE SHOWN) 25x25mm.
I. J I. J
C. J C. J · IN FIVE COURSES IMMEDIATELY BELOW THE WALL
7. 50mm BLINDING LAYER UNDER ALL FOUNDATIONS.
C. J · PLATE OR ROOF SLAB. EXTENDING 600mm BEYOND
I. J
I. J
C. J
OPENING.
4270
8. CONCRETE COVER TO REINFORCEMENT:
.J
I.J
I.J
.J
C
5 Courses
C
425mm
· IN EVERY COURSE ABOVE ALL LINTELS EXTENDING FOUNDATIONS - 50mm
I. J
I. J
85mm
STEP
.J
C. J
600mm BEYOND OPENINGS.
.J
I. J C7
I.J
9. ALL FOUNDATION EXCAVATIONS MUST BE INSPECTED AND APPROVED
I. J
C
I. J
I. J
Detail A C. J
BY THE ENGINEER BEFORE PLACING OF REINFORCEMENT OR CASTING
5 I. J
I. J BRICKFORCE TO BE DISCOUNTED AT ARTTICULATION OF CONCRETE. IF THE FOUNDING LEVEL AS PER DRAWING IS NOT
I. J
I. J
I. J I. J
JOINTS.
1730
SUITABLE, FURTHER EXCAVATIONS SHALL BE DONE TO A DEPTH AS
C
I. J I. J
C. J
.J
.J
I. J DETERMINED BY THE ENGINEER ON SITE. THE ENGINEER MAY
I.J
I.J
I. J I. J INSTRUCT THAT CERTAIN EXCAVATIONS BE BACKFILLED WITH MASS
I. J I. J C. J MINIMUM LAP LENGTH TO BE :
6
85mm
STEP
I. J CONCRETE TO REQUIRED LEVEL. (CLASS AS PER ITEM5 ABOVE).
I. J I. J I. J BRICKFORCE - 300mm
I. J
I. J
I. J
I. J
I. J
C. J
C. J
10.LAP AND ANCHORAGE LENGTH 50 x DIAMETER OF REINFORCEMENT.
I. J
I. J
I. J
I. J
I. J
I. J
I. J
I. J
I. J
I. J
I. J
I. J
I. J
I. J
I. J LINTELS TO BE PLACED ABOVE ALL WINDOWS,
I.J
I.J
I. J I. J 125mm THICK SURFACE BED WITH I. J OPENINGS AND EXTERNAL DOORS. TYPICAL CAVITY WALL DETAILS SHOWING OF 11. AFTER PLACING, ALL REINFORCEMENT MUST BE CHECKED AND
4500
C. J MESH REF. 245 - T. O. C : + 0.255mm I. J APPROVED BY THE ENGINEER ON SITE BEFORE CASTING OF CONCRETE.
I. J I. J 125mm THICK SURFACE BED WITH B B
VERTICAL PLACEMENT OF BUTTERFLY TIES
I.J
I.J
85mm
STEP
ALL MASONRY TO BE CONSTRUCTED IN STRETCHER
I.J
MESH REF. 245 - T. O. C : + 0.255mm --- ---
I. J
I. J
I. J
C C SCALE 1 : 10 12.NO HOLES OR NOTCHES SHALL BE CUT, CHIPPED OR FORMED IN
--- --- BOND, AND USING CLAY MASONRY UNITS OF MIN CONCRETE UNLESS APPROVED BY THE ENGINEER.
I. J
I. J
10MPa IN STRENGTH USING CLASS 2 MORTAR.

I. J I. J I. J I. J I. J I. J I. J
13.DURING COLD OR WET WEATHER CONCRETE MUST BE
7 I. J HANDLED IN ACCORDANCE WITH SPECIFICATIONS.
I. J I. J I. J
I. J
2030
C. J
C. J
C. J
C. J
85mm
STEP
14.REMOVAL OF SHUTTERING TO BE DONE IN ACCORDANCE WITH
I.J
I.J
I. J
I. J I. J I. J C. J SPECIFICATIONS.
C. J
8
I. J I. J I. J I. J I. J I. J I. J I. J 15.LOADINGS ON CONCRETE FIRST FLOOR SLABS MAXIMUM
C. J 100kg/m².
I. J
I. J
I. J
16.LOADING:
3850
S.C.J
I.J
I.J
I.J
I.J
I.J
MESH REF. 245 - T. O. C : + 0.255mm
PERMISSIBLE BEARING PRESSURE:
I. J
I. J
C. J
C. J
MESH REF. 245 - T. O. C : + 0.255mm
I. J COLUMN BASES - 150Kpa

I. J I. J I. J I. J I. J I. J
I.J
C. J
9 C. J I. J NOMINAL IMPOSED FLOOR LOADS:
I. J I. J I. J 10mm POLYSULPHIDE
S.C.J S.C.J S.C.J
.J
JOINT SEALER
C
.J
C
ALL DIMENSIONS TO BE CHECKED ON SITE PRIOR
I.J
I.J
ROOF SLABS - 1.5KN/m²
I. J
I. J
C. J DPC
S.C.J
TO THE COMMENCEMENT OF ANY WORK. 10mm IMPREGNATED
MESH REF. 245 - T. O. C : + 0.255mm

SOFTBOARD

125mm THICK SURFACE BED WITH ANY DISCREPANCIES TO BE REPORTED TO THE 17.FOUNDING DEPTH :
I. J
I. J
I. J
I. J MESH REF. 245 - T. O. C : + 0.255mm AUTHOR IMMEDIATELY.

5550
ALL EXCAVATION DEPTHS TO BE AT A PROVISIONAL DEPTH OF 1.275m
I.J
I.J
I. J THIS DRAWING IS TO BE READ IN
BELOW FINISHED PLATFORM LEVEL.
C. J
C. J
I. J I. J C. J CONJUNCTION WITH ALL ARCHITECTURAL AND
I.J
I. J
125mm THICK SURFACE BED WITH STRUCTURAL DRAWINGS.
WHERE CONDITIONS ARE NOT SUITED FOR A NORMAL RAFT AN
I.J
I.J
MESH REF. 245 - T. O. C : + 0.255mm
C. J DPM TURNED UP INTO
170mm
ALLOWANCE FOR IMPORTING OF SUITABLE MATERIAL TO BE PROVIDED

C. J
STEP

MESH REF. 245 - T. O. C : + 0.255mm JOINT AND TUCKED AT A DEPTH OF 450mm ( 3 LAYERS 150mm) BELOW FOOTINGS AND
C. J I. J I. J S.C.J UNDER DPC
C. J C. J COMPACTED TO 97% MOD ASSHTO FOR MODIFIED STRIP FOOTING.
10
I. J I. J
C. J
I. J - ISOLATION JOINT DETAIL 18.BACKFILL:
I.J
C. J
I. J
I. J
I. J
( FOR CAVITY WALL )

SELECTED FILL BENEATH SURFACE BEDS TO BE SELECTED GRANULAR
170mm
STEP
SCALE 1 : 10
3880
MATERIAL COMPACTED IN 150mm LAYERS TO 95% MOD. AASHTO
S.C.J
DENSITY. FOUNDING LEVEL TO BE CONFIRMED BY THE ENGINEER.
I.J
I.J
S.C.J
Detail A
Detail A
Detail A
Detail A
Detail A I. J
D
---
I. J
C
I. J
.J
85mm
I. J
STEP
11
I. J
I.J
I. J
I. J
C. J
C. J
85mm
STEP
2115
.J
C1
C
C. J C. J C9
I. J
MESH REF. 245 - T. O. C : + 0.170mm
MESH REF. 245 - T. O. C : + 0.085mm

12 DESIGN CONSULTANT :
C. J
.J
.J
C
C
I. J
C
C. J
.J
N
.J
MESH REF. 245 - T. O. C : + 0.255mm
C
C2 C. J D
---
4605
S.C.J
800 800
I. J
E BUSINESS ADDRESS : CONTACT DETAILS :

---
85mm
STEP
C
C
.J
.J
CAVITY
I. J I. J Office 1B Deodant Building Tel : (031) 701 1038
C3
13 C8
I. J I. J CAVITY NOTES : 10 Payne Street, Tel : (031) 701 1038
TOTAL WIDTH
I. J

3135
C. J
· ALL MORTAR DROPPINGS SHOULD BE CLEANED

AND NEVER ALLOWED TO BUILD UP IN THE BASE 3600 Website : www.vumesa.co.za
85mm
STEP
C6 C5 C4
CAVITY
14 FOR DESIGN CONSULTANT
· NO MORTAR TO BE LEFT TO COLLECT ON THE
C
FUNCTION NAME SIGNATURE

.J
.J
C
WALL TIES
E
---
DRAWN BY T. HLATSHWAYO
· CONSTRUCTION TO BE IN LOW-LIFTS N.E 1M MAX.
TYPICAL DETAILS OF HORIZONTAL PLACEMENT OF BUTTERFLY TIES DESIGN CHECKED BY N. A MBATHA
SCALE 1 : 10 DRAWING CHECKED BY N. A MBATHA
SURFACE BED AND COLUMN LAYOUT PLAN APPROVAL CONSULTANT
SCALE 1 : 100
NAME : N.A MBATHA SIGNATURE
DATE : 31 / 01 / 2020 PR. ENG.NO. 201470322
CONSTRUCTION JOINT DIMENSIONS APPROVED JOINT SEALANTS : APPROVED JOINT SEALANTS :

SAW CUT DEPTH APPROVED JOINT SEALANTS :
SLAB THICKNESS "A" "B" "C" "E"
"D"mm SLAB THICKNESS "A"
· SIKAFLEX 35SL "D"mm A ISSUED FOR INFORMATION 31/01/2020 T. H
100 37 3 20 10
· SIKAFLEX 35SL · SIKAFLEX 35SL
100 25 REV NO. DESCRIPTION : DATE DRAWN
125 47 3 25 13 · DURAKOL 25
150 56 4 30 15 125 35 · DURAKOL 25 · DURAKOL 25
150 40
175 66 4 35 18 · PROSTRUCT 642 OR 644 175 45
PROJECT DESCRIPTION
200 75 5 40 20 · PROSTRUCT 642 OR 644
225 85 5 45 23 200 50 · PROSTRUCT 642 OR 644
225 55
250 94 6 50 25
250 65 LIMPOMPO DEPARTMENT OF SOICIAL
MESH REF. 245 PLACED 125mm THICK REINFORCED DEVELOPMENT
30mm FROM TOP OF SLAB SURFACE BED
10mm THICK JOINTEX WITH 10x10 APPROVED SEALANT 200
10x10mm TEAR OFF STRIP WITH POLYETHYLENE BOND-
BREAKER BACKING TAPE
10x10 APPROVED SEALANT MESH REINFORCEMENT SEAL JOINT WITH APPROVED JOINT REAMED TO 10x10mm TSHILWAVHUSIKU CLINIC
25
WITH POLYETHYLENE BOND- JOINT SEALANT WITH BACKING
150 150
MIN 300 LAPS A MINIMUM OF 7 DAYS AFTER

BREAKER BACKING TAPE MESH TO STOP 75mm
EACH SIDE OF JOINT
CORD AND BOND BREAKER STRIP CONCRETE IS CAST MESH REINFORCEMENT
MIN 300 LAPS
NEW MULTI PURPOSE OFFICE BLOCK
MESH TO STOP 75mm
250 MICRON PVC MEMBRANE
EACH SIDE OF JOINT DRAWING TITLE :
B A
MATERIAL COMPACTED TO
AND COMPACTED FILL
95 % MOD. AASHTO IN
150mm LAYERS
A
C
D
SURFACE BED LAYOUT PLAN AND

A B
TYPICAL LAYERWORKS UNDER SLABS TYPICAL DETAILS
100
SCALE 1 : 20
E 10mm THICK JOINTEX OR SIMILAR
BOND-BREAKING COMPOUND APPROVED COMPRESSABLE
(LIME WASH OR BITUMEN) JOINT FILLER WITH 10x10mm
APPLIED TO EXPOSED JOINT MESH TO BE CONTINUOUS TEAR-OFF STRIP
3
THROUGH EACH SIDE OF JOINT 3mm WIDE SAW CUT.
R1
SURFACE BEFORE 2ND POUR
CUT AS SOON AS CONCRETE
HAS HARDENED SUFFICIENTLY PROJECT NUMBER CONTRACT NUMBER :
TO PREVENT DISLODGEMENT OF
AGGREGATE PARTICLES (8 TO VUM_77_12/19_001 TEC05/2018
DETAIL - CJ DETAIL S.C.J 24 HOURS AFTER CASTING)
DETAIL I.J DRAWING STATUS : SCALE SIZE
TYPICAL DETAILS OF BUTTERFLY WALL TIES
SCALE 1 : 25 FOR INFORMATION AS SHOWN A1
SCALE 1 : 25 SCALE 1 : 25 SCALE 1 : 5
31-01-2020 P4 - 01 - 200 1 of 1 A

NOTES / COMMENTS :
I H G F
14135
45 deg KNEE BRACES STRUCTURAL STEEL ELEMENTS
60x60x6L (SECTION 7-7)
TOTAL LENGTH OF MEMBER (m)
TOP CHORD 14,10
1237
BOTTOM CHORD 14,10
551
DIAGONALS 17,00
VERTICALS 9,79
935 1350 1550 1550 1550 1550 1550 1550 1550 1000
7 7
GRID LINE SECTION 7 - 7

SCALE 1 : 50
I H G
I H G F
45 deg KNEE BRACES
60x60x6L
STRUCTURAL STEEL ELEMENTS 8905

(SECTION 12-12)
TOTAL LENGTH OF MEMBER (m)
TOP CHORD 8,91
983
551
RAFTER IPE 200 RAFTER IPE 200 BOTTOM CHORD 8,91
5 5 DIAGONALS 10,76
45 deg KNEE BRACES
60 x 60 x 6L 6,18
12 12
2120
VERTICALS 935 1350 1550 1550 1550 1550 420
6 6
GRID LINE SECTION 12 - 12
3° ROOF PITCH
SCALE 1 : 50
50x50x3L 50x50x3L
DESIGN CONSULTANT :
TRUSS
TRUSS
TRUSS
TRUSS
TRUSS
7 7
BUSINESS ADDRESS : CONTACT DETAILS :
Office 1B Deodant Building Tel : (031) 701 1038
8 8 10 Payne Street, Fax : (031) 701 0963
FOR DESIGN CONSULTANT

9 9 DESIGNED BY S. KHUMALO
50x50x3L 50x50x3L
S. KHUMALO
e:\sntdp projects\77. vumesa projects\# p01 - ldsd developemt projects\information received\issued structural details\idt limpopo structural drawings.dwg
DRAWN BY
3° ROOF PITCH
DESIGN CHECKED BY N. BUTHELEZI

DRAWING CHECKED BY N. BUTHELEZI
APPROVAL CONSULTANT
NAME : V. H. KHUMALO SIGNATURE
DATE : 06 / 02 / 2020 PR. ENG.NO. 201070114
50x50x3L 50x50x3L
10 10
A ISSUED FOR INFORMATION 06/02/2020 S. K.

11 11 REV NO. DESCRIPTION : DATE DRAWN
50x50x3L 50x50x3L
3° ROOF PITCH
PROJECT DESCRIPTION
45 deg KNEE BRACES
12
60 x 60 x 6L
12 F LIMPOMPO DEPARTMENT OF SOICIAL
2120
DEVELOPMENT
TRUSS
TRUSS
TRUSS
IPE 200
50x50x3L 50x50x3L
TRUSS MEMBERS DESIGNATION:
TOP CHORD - 100 x 100 x 8 300x16PL x 250
BOTTOM CHORD - 90 x 90 x 8 90
DIAGONALS - 60 x 60 x 6
R.C RING BEAM

13 13 DRAWING TITLE :
350
RAFTER IPE 200 RAFTER IPE 200
25
PURLINS - 150 x 50 x 20 x 20
VERTICALS - 70 x 70 x 6
4-M20 H.D
EAVES BEAM - IPE-AA 200 BOLTS
70
TYPICAL TRUSS TO RING

ROOF DETAILS
I H G F BEAM CONNECTION
ROOF PLAN
SCALE 1 : 100 PROJECT NUMBER CONTRACT NUMBER :
VUM_77_12/19_001 TEC05/2018
DRAWING STATUS : SCALE SIZE
FOR INFORMATION AS SHOWN A1
06-02-2020 STR - 310 1 of 1 A

NOTES / COMMENTS :
150x50x20x20
G H I
11 PURLINS
15 15
1:50 C1
12
150x50x20x20
PURLINS IPE 200
C1 COLUMN UNDER
C1
C1=150x4.0mm CHS IPE 200
200
2 M16 BOLTS
R.C COLUMN
1:50 10mm PLATE
350x350mm DETAIL 1
13 C1
1:50
1:50
C1 C1
C1
DETAIL 1 TYPICAL DETAIL OF
14
COLUMN CONNECTION
CATCHPIT
SCALE 1 : 25
180 R.C SLAB TO FALL 1:50

C1 I H AS INDICATED 4mm FULLY G
TORCHED WATERPROOFING
TORCH-ON BITUMEN MEMBRANE.
IPE 200 RAFTER SECTION

ROOF PLAN SCALE 1 : 50
SCALE 1 : 100
DESIGN CONSULTANT :
864 885 885 885 864
100x100x3mm
SHS
2337
Office 1B Deodant Building Tel : (031) 701 1038
10 Payne Street, Fax : (031) 701 0963
FOR DESIGN CONSULTANT

2337
1:50
DESIGNED BY S. KHUMALO
100x100x3mm S. KHUMALO
DRAWN BY
SHS
DESIGN CHECKED BY N. BUTHELEZI
100x100x10mm
C1 PLATE
C1 COLUMN UNDER
APPROVAL CONSULTANT
C1=150x4.0mm CHS NAME : V. H. KHUMALO SIGNATURE
10 1.8m M20 HIGH DATE : 06 / 02 / 2020 PR. ENG.NO. 201070114
1:50
2337
TENSILE BAR
6mm WELD M20 HIGH

180 R.C SLAB TO FALL 1:50 C1 TENSILE BAR
AS INDICATED 4mm FULLY 10mm PLATE
14
4xM12 BOLTS
11
50
1:50
1: A ISSUED FOR INFORMATION 06/02/2020 S. K.
2337
6mm WELD
150x4.0mm REV NO. DESCRIPTION : DATE DRAWN
CHS 75x50x20x2mm
C1 PURLINS
C1 C1 12 PROJECT DESCRIPTION
14
CATCHPIT
LIMPOMPO DEPARTMENT OF SOICIAL

E D C B
DEVELOPMENT
30x30x3mm
EQUAL ANGLE
ROOF PLAN
2337
SECTION
SCALE 1 : 100
VERANDA ROD SUPPORT

DETAIL DRAWING TITLE :
SCALE 1 : 25
ROOF PLAN
SCALE 1 : 50
CONCRETE COVERED WALKWAY
AND CANOPY DETAIL
PROJECT NUMBER CONTRACT NUMBER :

VUM_77_12/19_001 TEC05/2018
06-02-2020 STR - 330 1 of 1 A

NOTES / COMMENTS :
E D
G F L K J
180 R.C SLAB 280
230x350mm R.C TO FALL AS PER
ENGINEER DETAILS 180 R.C SLAB
BEAM OR 180 RIB & BLOCK SLAB
1:50
425
1:50
150x4.0 CHS TYPICAL RING

SECTION 9 - 9 SECTION 12 - 12 BEAM
SECTION 8 - 8 SCALE 1 : 50 SCALE 1 : 50 SCALE 1 : 25
SCALE 1 : 50
G H
425
11 280
15 15
1:50 C1
SECTION 11 - 11
SCALE 1 : 20
12 5300x425x280mm R.C
BEAM
C1 COLUMN UNDER
C1
11
C1=150x4.0mm CHS
R.C COLUMN
1:50
11
350x350mm
13 C1
1:50
1:50
SECTION 10 - 10
SCALE 1 : 50
C1 C1
C1
14
CATCHPIT I H G F
180 R.C SLAB TO FALL 1:50
C1 I H AS INDICATED 4mm FULLY G
ROOF PLAN
BM 1=280x425 DP
@ LVL 0.000
SCALE 1 : 100
BM 1=280x425 DP
5
@ LVL 0.000
DESIGN CONSULTANT :
2465
BM 1=280x425 DP
6
@ LVL 0.000
BM 1=280x425 DP
230 230 Office 1B Deodant Building Tel : (031) 701 1038
@ LVL 0.000
10 Payne Street, Fax : (031) 701 0963
1:50 7 Pinetown, E-mail : [email protected]
455
BM 1=280x425 DP
8 FOR DESIGN CONSULTANT
@ LVL 0.000
170
2075
DESIGNED BY S. KHUMALO
20120
SECTION 15 - 15 DRAWN BY S. KHUMALO
BM 1=280x425 DP
SCALE 1 : 25 DESIGN CHECKED BY N. BUTHELEZI
@ LVL 0.000
9 APPROVAL CONSULTANT
NAME : V. H. KHUMALO SIGNATURE
29865
DATE : 06 / 02 / 2020 PR. ENG.NO. 201070114
BM 1=280x425 DP
@ LVL 0.000
BM 1=280x425 DP
@ LVL 0.000
1:50 10
A ISSUED FOR INFORMATION 06/02/2020 S. K.
REV NO. DESCRIPTION : DATE DRAWN
PROJECT DESCRIPTION
1960
C1
BM 1=230x425 DP
C1 COLUMN UNDER 230 230 LIMPOMPO DEPARTMENT OF SOICIAL
@ LVL 0.000
C1=150x4.0mm CHS
11 DEVELOPMENT
1:50 10 1:50
455
180 R.C SLAB TO FALL 1:50 C1

CHS FIXED ON 12
7975
BM 1=280x425 DP
250x300x10mm PLATE
AS INDICATED 4mm FULLY
4-M16 BOLTS
@ LVL 0.000
TORCHED WATERPROOFING 150x4.0mm
BM 1=230x425 DP
TORCH-ON BITUMEN MEMBRANE. CHS
14
DRAWING TITLE :
@ LVL 0.000
11
50
1:50
1:
150x4.0mm
CHS
C1 C1 C1 12 SLAB & STEEL ROOF DETAILS
14
CATCHPIT 13
SECTION 14 - 14
E D C B SCALE 1 : 25
ROOF PLAN PROJECT NUMBER CONTRACT NUMBER :

SCALE 1 : 100 RING BEAM LAYOUT VUM_77_12/19_001 TEC05/2018
SCALE 1:100
06-02-2020 STR - 300 1 of 1 A

Structural Engineering Drawings

Uploaded by

Copyright:

Available Formats

Structural Engineering Drawings

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Structural Engineering Drawings

Uploaded by

Copyright:

Available Formats

STRUCTURAL ENGINEERING DRAWINGS

2. NO DEVIATION FROM THE DETAILS ON THE DRAWING WILL

Approved compacted in layers n.e 150mm

Min. 3 Layers of G5 Material or Similar

TRENCHES - CLASS F 25/19

Approved compacted in layers n.e 150mm

Min. 3 Layers of G5 Material or Similar

TO 95% MOD AASHTO

1000 x 300 - R.C Footing

1000 x 300 - R.C Footing

SECTION B - B ( 280mm CAVITY WALL )

7. 50mm BLINDING LAYER UNDER ALL FOUNDATIONS.

BY THE ENGINEER BEFORE PLACING OF REINFORCEMENT OR CASTING

OF CONCRETE. IF THE FOUNDING LEVEL AS PER DRAWING IS NOT

1000 x 300 - R.C Footing

1000 x 300 - R.C Footing

1000 x 300 - R.C Footing

800 x 300 - R.C Footing

800 x 300 - R.C Footing

800 x 300 - R.C Footing

· DPC TUCKED INTO BED JOINT

800 x 300 - R.C Footing DPC

1000 x 300 - R.C Footing

800 x 300 - R.C Footing

600 x 300 - Footing

600 x 300 - Footing

Approved compacted in layers n.e 150mm

Min. 3 Layers of G5 Material or Similar

TO 95% MOD AASHTO

800 x 300 - R.C Footing

800 x 300 - R.C Footing

WHERE CONDITIONS ARE NOT SUITED FOR A NORMAL RAFT AN

800 x 300 - R.C Footing

SECTION A - A ( 345mm CAVITY WALL ) 18.BACKFILL:

DENSITY. FOUNDING LEVEL TO BE CONFIRMED BY THE ENGINEER.

11 1000 x 300 - R.C Footing 800 x 300 - R.C Footing

1000 x 300 - R.C Footing

1.4 x 1.4 X 0.3m

R.C Pad Footing F. P. L

MEASURES TO BE CARRIED OUT WITH THE APPROVAL OF THE

1.4 x 1.4 X 0.3m 10 Payne Street, Tel : (031) 701 1038

COURSE - MAX. 425

Footing Depth + 600 FUNCTION NAME SIGNATURE

COURSE - MAX. 425

f:\sntdp projects\77. vumesa projects\current projects\04 - tshilwavhusiku site\sntdp_77_p4_working drawing.dwg

85mm STEP DRAINAGE FROM THE FOOR SLAB BUILDING

NEW MULTI PURPOSE OFFICE BLOCK

FOUNDING DEPTH TO BE DETERMINED FOUNDING DEPTH TO BE DETERMINED BY THE ENGINEER ON SITE

25Mpa CONCRETE 25Mpa CONCRETE FOOTING FOOTING

TO THE COMMENCEMENT OF ANY WORK. PROJECT NUMBER CONTRACT NUMBER :

C Copyright reserved - Vumesa (Pty) Ltd

COLUMN - A : 203 x 133 x 25 mm

REINFORCEMENT OF STUB COLUMN SUPPORT FOR C7

LEVELING BASE PLATE

f:\sntdp projects\77. vumesa projects\current projects\04 - tshilwavhusiku site\sntdp_77_p4_working drawing.dwg

4 No. 22mm Ø HOLES

1. ALL EXPOSED EDGES TO BE CHAMFERED 20x20

220 x 220 x 6 UNLESS OTHERWISE NOTED

90x90x20mm THICK 3. MINIMUM LAP LENGTH = 45 x DIA. OF BAR

225 x 225 x 4.5 mm