Agilent SPS 4 Autosampler Consumables Ordering Guide (January 2019, Version 1.

5)

Agilent SPS 4 Autosampler

Consumables Ordering
Guide

This Ordering Guide provides an

illustrated listing of the consumables
for the Agilent SPS 4 autosampler,
used with the AA, MP-AES, ICP-
OES and ICP-MS systems. Some of
the consumables used with this
autosampler are subtly different to
those used with the previous SPS 3
autosampler, although they may
look similar (e.g. probes). Many of
the consumables are common
however (e.g. racks, tubes, pump
tubing).

This illustrated listing should enable

you to easily identify any
consumables that are required and
assist you with customer inquiries
and requests for quotation.
In case of any query, please contact
your local Product Specialist before
quoting.
Contents
After market options to enhance functionality
Cover options
After market options for ICP-MS
Probes for the SPS 4
3 bridged peristaltic pump tubing
Standard racks
Sample racks and rack overlays
Test tubes and vessels
Miscellaneous SPS 4 supplies
Miscellaneous SPS 4 tubing and connectors

Page 1 of 10
Agilent SPS 4 Autosampler Consumables Ordering Guide (January 2019, Version 1.5)

Back to Contents

Part Number Description

After market options (or kits) to enhance functionality

G8410-68260 High uptake volume rinse kit for SPS 4

Recommended for use with the SPS 4 autosampler when connected to the SVS 2+ or
ISIS 3. Allows rinse uptake rate to be increased to 25mL/min.
Includes sample qty of wide bore peristaltic pump tubing with purple/black tabs (4 pump
tubes only), barb connectors and 2m length of PTFE tubing

G8410-68261 SPS 4 rinse tube kit, for low volatile organics

Allows use of low volatile organic solvents in rinse station.
Includes 1m capillary tubing, sample qty of 3-bridged grey/grey PVC SolvaFlex
peristaltic pump tubing (4 pump tubes only), barb connector 2.5mm-1.5mm and solvent
resistant tubing for inlet solvent and waste outlet from rinse station.

G8410-68262 Pump drain kit for SPS 4 autosampler, 1/p

Provides the components required to allow the liquid overflow to be pumped from the
rinse station.
Includes sample qty of wide bore peristaltic pump tubing with purple/white tabs (4 pump
tubes only), barb connectors and 2.5m length of PVC Solvaflex tubing to enable
connection to a remote pump (not supplied).

Part Number Description

Cover options

G8410-60100 SPS 4 Autosampler cover kit, 1/pk

Encloses the autosampler to help reduce sample and standard contamination from dust
and drafts. Provision for optional purge or exhaust connection to remove corrosive or
solvent fumes (requires but does not include the ducting hose which should be ordered
separately (pn 5043-0065)).

Optional integrated cover shown in fixed open position, allowing easy access to
samples.

Page 2 of 10
Agilent SPS 4 Autosampler Consumables Ordering Guide (January 2019, Version 1.5)

Back to Contents

Part Number Description

After market options for ICP-MS ONLY

G8410-68270 Well plate startup kit for SPS 4, 1/pk

Allows the SPS 4 autosampler to be adapted to sample from deep well 96 well plates.
Includes well plates (10/pk), well plate adapter and sample probe.

NOTE: For ICP-MS ONLY

This functionality ONLY supported with the ICP-MS MassHunter software

G3139-68000 Microflow neb. PFA(200) w/SPS 4 probe kit

Microflow PFA(200) nebulizer with integrated probe for SPS 4 autosampler, flow rate
200 µL/min.; sample uptake tube terminates as a sampling probe.
Used with 7700/7800/7900, and 8800 Series ICP-MS for high purity and hydrofluoric
acid samples.

G8410-60180 Nebulizer probe mount kit for SPS 4 autosampler, 1/pk

Required to mount a nebulizer-integrated sample probe (supplied separately) onto the
probe arm of the Agilent SPS 4 autosampler.
This provides an integrated nebulizer/probe assembly for ultra-clean applications.

NOTE: Order G3139-68000 if ordering the PFA nebulizer together

Page 3 of 10
Agilent SPS 4 Autosampler Consumables Ordering Guide (January 2019, Version 1.5)

Back to Contents

Part Number Description

Consumables to support use of well plates with SPS 4 with ICP-MS

G8410-40003 Well plate tray adaptor kit for SPS 4, 1/pk

Allows 96 position deep well plates to be located on the sample tray of the SPS 4
autosampler (raises the height of the well plate on the autosampler).
Requires, but does not include the sample probe.

NOTE: For ICP-MS ONLY

This functionality ONLY supported with
the ICP-MS MassHunter software

G8410-80105 SPS 4 sample probe with red marker, suits SPS 4 Microtiter tray, 1/pk
Required when using the SPS 4 autosampler with microtiter tray for sampling from a 96
position well plate.
Requires, but does not include the well
plate tray adaptor kit or any compatible
well plates.

5043-9310 96-well plate, 0.5 mL, round wells, U shape, polypropylene, 14 mm, 30/pk
Spare well plates suitable for use with the SPS 4
autosampler when using the optional microtiter tray for
sampling from a 96 position well plate.

5043-9311 96-well plate, 0.5 mL, round wells, U shape, polypropylene, 14 mm, 120/pk
Spare well plates suitable for use with the SPS 4
autosampler when using the optional microtiter tray for
sampling from a 96 position well plate.

Page 4 of 10
Agilent SPS 4 Autosampler Consumables Ordering Guide (January 2019, Version 1.5)

Back to Contents

Part Number Description

Replacement Probes for the SPS 4

The colored markers on the sample line of the probe provides
easy visual identification of the probe ID.

G8410-80100 SPS 4 probe 0.25mm-id with red marker, inert, FEP sleeved, 1/pk
Recommended when using the Agilent SPS 4 autosampler with ICP-MS instruments.

G8410-80101 SPS 4 probe 0.5mm-id with yellow marker, inert, FEP sleeved, 1/pk
Recommended when using the Agilent SPS 4 autosampler with ICP-MS instruments.

NOTE: Standard probe for ICP-MS configuration

G8410-80102 SPS 4 probe 0.8mm-id with green marker, inert, FEP sleeved, 1/pk
Recommended when using the Agilent SPS 4 autosampler with AA, ICP-OES, MP-AES
and ICP-MS instruments.

NOTE: Standard probe for AA/MP-AES/ICP-OES configuration

G8410-80103 SPS 4 probe 1.0mm-id with blue marker, inert, FEP sleeved, 1/pk
Recommended when using the Agilent SPS 4 autosampler with AA, ICP-OES and MP-
AES instruments.

G8410-80104 SPS 4 probe 1.2mm-id with black marker, inert, FEP sleeved, 1/pk
Recommended when using the SPS 4 autosampler with viscous solutions and high
matrix samples for AA, ICP-OES and MP-AES instruments.

3 bridged peristaltic pump tubing for use with rinse pump

5043-0063 Peristaltic pump tubing, PVC SolvaFlex, 3 bridged, purple/white tabs (pk/12 tubes)
For use with SPS 4 when pumping acidic or aqueous based rinse

3710049000 Peristaltic pump tubing, PVC SolvaFlex, 3 bridged, grey/grey tabs (pk/12 tubes)
Standard tubing supplied with the autosampler
for the rinse pump.
For use with aqueous samples on
AA, MP-AES, ICP-OES and
ICP-MS instruments

Page 5 of 10
Agilent SPS 4 Autosampler Consumables Ordering Guide (January 2019, Version 1.5)

Back to Contents

Part Number Description

3710069300 Peristaltic pump tubing, PVC SolvaFlex, 3 bridged, yellow/yellow tabs (pk/12
tubes)
For use with low volatile organic solvents.

3710034800 Peristaltic pump tubing, PVC SolvaFlex, 3 bridged, black/black tabs (pk/12 tubes)
For use with low volatile organic solvents.

3710069200 Peristaltic pump tubing, PVC SolvaFlex, 3 bridged, black/black tabs with flared
ends (pk/12 tubes)
For use with low volatile organic solvents.

3710069000 Peristaltic pump tubing, PVC SolvaFlex, 3 bridged, orange/yellow tabs with flared
ends (pk/12 tubes)
For use with low volatile organic solvents.

3710057500 Peristaltic pump tubing, Santoprene, 3 bridged, grey/grey tabs (pk/6 tubes)
For use with ketone-based solvents.

3710069100 Peristaltic pump tubing, Viton, 3 bridged, black/black tabs

with flared ends (pk/12 tubes)
For use with aromatic organic solvents

Page 6 of 10
Agilent SPS 4 Autosampler Consumables Ordering Guide (January 2019, Version 1.5)

Back to Contents

Part Number Description

SPS 4 standard racks

G8410-40000 34 position standards rack for SPS 4 autosampler 1/pk

Rack provides 12 locations for 50mL 30mm OD centrifuge tubes plus 22 locations for
18mm OD test tubes

NOTE: Standard rack for AA/MP-AES

& ICP-OES configuration

NOT supported with the ICP-MS Mass Hunter SW

G8410-40001 5 position standards rack for SPS 4 autosampler 1/pk

Rack provides 5 locations for 250mL 60mm OD narrow neck sample containers

NOTE: Standard rack for ICP-MS

configuration

The bottles shown in this image

are NOT supplied with the rack.

NOT supported with the AA SpectrAA SW

SPS 4 sample racks and rack overlays

6610026400 Sample rack for 13 mm od tubes, 90 positions, 1/pk

6610025400 Sample rack for 16 mm od tubes, 60 positions, 1/pk

6610025500 Sample rack for 20 mm od tubes, 40 positions, 1/pk

6610026500 Sample rack for 25 mm od tubes, 24 positions, 1/pk

6610026600 Sample rack for 30 mm od tubes (50mL centrifuge tubes), 21 positions, 1/pk

Page 7 of 10
Agilent SPS 4 Autosampler Consumables Ordering Guide (January 2019, Version 1.5)

Back to Contents

Part Number Description

6610026100 Rack overlay for 60-position sample rack, 1/pk

Allows 13 mm od and some 16 mm OD tubes to be
used in 60-position rack
(2 recommended per rack)

6610026000 Rack overlay for 40-position sample rack, 1/pk

Allows 18 mm od tubes to be used in 40-position rack (2 recommended per rack)

Test tubes and vessels to use with SPS 4 sample and standard racks

5043-0064 Sample bottle 250mL for 5x60mm std rack, 1/pk

60mm-od narrow neck LDPE for 5 position
standard rack used with SPS 4 autosampler.

NOTE: The rack shown in this image is NOT

supplied with the bottles.

190065200 Centrifuge tubes polyprop. 50 mL, 500/pk

Screw-capped, 29 mm od, polypropylene

00000001600L Polypropylene tubes, 17 mm x 130 mm, 1000/pk

3710051100 Polypropylene tubes, 16mm od x 125 mm, 125/pk

NOTE: Not recommended for use with the SPS 4

without using a rack overlay (pn 6610026100)
to ensure better tube location in the sample rack.

190049700 Polypropylene tubes 16mm od x 125mm, 1000/pk

These are the same tubes as pn 3710051100 – just supplied as a larger quantity

NOTE: Not recommended for use with the SPS 4 without using a rack overlay
(pn 6610026100) to ensure better tube location in the sample rack.

Page 8 of 10
Agilent SPS 4 Autosampler Consumables Ordering Guide (January 2019, Version 1.5)

Back to Contents

Part Number Description

Miscellaneous SPS 4 supplies

G8410-60140 Single port fixed wash reservoir for SPS 4, 1/pk

G8410-60150 Dual port fixed wash reservoir for SPS 4, 1/pk

G8410-80111 Standard rack location mat for SPS 4, 1/pk

G8410-80605 Spill tray kit for SPS 4 autosampler, 1/pk

Includes spill tray and warning label

G8410-40004 Tube anchor for SPS 4 autosampler, 2/pk

Secures transfer tubing from probe to
instrument on arm of probe carriage to
eliminate tangling.

G8410-40005 Cable ducting for SPS 4 autosampler, 1/pk

Page 9 of 10
Agilent SPS 4 Autosampler Consumables Ordering Guide (January 2019, Version 1.5)

Back to Contents

Part Number Description

Miscellaneous SPS 4 tubing and connectors

5043-0065 PVC flexible ducting 50mm-id for SPS 4 autosampler, 5m length

Spare ducting to enable removal of fumes from the autosampler
with the cover fitted. Fitted with 56mm OD cuffs.
Ducting is light, flexible and easy to install.

G8410-80122 PVC waste tubing for SPS 4, 8mm od x 5mm id, 2m

Replacement tubing to connect from waste outlet of rinse station of SPS 4 autosampler.

G8410-80123 Tubing for supply of rinse solution to rinse station of SPS 4, 2.5mm id x 1m
Replacement tubing to connect from rinse solution supply to inlet of rinse station of
SPS 4 autosampler.

G8410-20012 Tubing-solvent resistant 0.093-in-ID, 2m

Replacement tubing for inlet solvent line to rinse station of SPS 4 autosampler.
Allows use of low volatile organic solvents in rinse station.

G8410-20013 Tubing-solvent resistant 0.187-in-ID, 2m

Replacement tubing for waste solvent outlet of rinse station of SPS 4 autosampler.
Allows use of low volatile organic solvents in rinse station.

0100-2846 Barb connector straight through 4.8 - 2.4mm ID

0100-2848 Barb connector straight-through 2.4mm-ID

G8410-80120 Nipple, PVDF, 5mm ID, SPS 4 rinse station

Replacement nipple for outlet waste from rinse
station of SPS 4 autosampler.

G8410-80121 Nipple, PP, 2.5mm ID, SPS 4 rinse station

Replacement nipple for inlet rinse supply to rinse
station of SPS 4 autosampler.

G8410-80124 Barb connector for SPS 4, 2.5mm-1.5mm ID, 1/pk

Straight-through connector for rinse tube kit used
with low volatile organics when using low volatile
organic solvents in SPS 4 rinse station

G8410-67001 Cable ties, natural polypropylene, 10/pk

Page 10 of 10