NOTICES The knowledge about motorcycle abrasion.

The first 1600 kilometers is very important for the vehicle's life. During this period, the correct way of abrasion makes sure the longest motorcycle's life and also shows the function of new vehicle fully. PREFACE
Thanks a lot for choosing the KEEWAY product SPEED which is two wheels motorcycle. We adopted advanced technique for this model, which can offer you a safe and joyful drive. Ride motorcycle is a very exciting activity, please read This the manual carefully the and correct know way the of requirements before driving. manual specifies maintainance. If you take care of your vehicle according to this manual, your vehicle will be in good condition for a long time. Our company has the technologist and the special department for technology supports. Our tenet is to 1 make our customers more satisfactory. We improve our products daily, which could bring changes to its appearance and the structure, if your motorcycle is not exactly same as this manual, we pray for your understanding.

WARNING/CAUTION/NOTICE
Please read this manual carefully. The words "warning","caution"and"Notice" mean different extent of important. Please pay more attention to this.

WARNING ----------- the activity indicated by

warning is refer to the driver's safety, without regard to this warning may cause an injury.

CAUTION ------------ In order to avoid bringing

damage to vehicle, it shows the actions that should be noticed by rider.

2.Many accidents often occurred because the drivers who have inadequate experiences to drive. Before driving, please confirm that the driver is qualified, and never lend the motorcycle to ones who do not have license. 3.The motorcycle driver should make himself obvious, in order to prevent from the accidents. Please wear in fresh color and with reflected one when on driving. Please do not drive too close with the car in order to avoid the collision. 4.Abide the law and regulation of country and local government Exceeding the limited speed is the main reason for many accidents, so notice to control the speed on driving. In order not to make other people be frighted and avoid affecting the driving, please give a signal before changing courses 2

NOTICE-----------this is an explanation to
maintaining or special terms This manual should to be regarded as a part of motorcycle. Please make sure to give this manual to the new owner when you transfer your vehicle.

SAFE NOTICE FOR MOTORCYCLE

WARNING: In order to guarantee the security, it needs special efforts to drive the motorcycle. You can drive after making it clear with its safe demanding .

SAFETY DRIVING RULES

1. Please check the motorcycle before starting the engine, and then you can drive out . In this way, it will prevent the accidents or devices from being damaged.

5. Dont be nervous when others drive towards you. Please pay more attention to the entrance and exit of yards and be careful when driving in the high way. 6. Grasp the handle bar and put your feet on the foot pedals on driving. 7. Refit the motorcycle and disassemble the spare parts will lead to be unsafe, at the same time it is illegal and will affect it with warranty maintenance. 8. The special required parts should not influence its security and function for drive.

3. Never wear long clothing which can bel be twisted by control lever, kick-starter, foot pedal or wheels.

SERIES NUMBER
Vehicle Identification Number (VIN) and Engine Number are used for motorcycle registeration. These numbers are helpful for you to place spare parts orders or ask for specific service. Write down VIN and Engine Number and keep them. Vehicle Identification Number (VIN) printed on the head tube of the frame. Engine Number printed on the left of crankcase. On the tube, you also can find Manufacturing Label on which are marked motorcycles model, description, displacement, date, factory and some 3

PROTECTIVE CLOTHING
1. Most fatal accidents due to the head injury of driver. Make sure to wear helmet, gloves and protective clothing. The passenger should also wear them. 2. The exhaust system will be very hot during driving and remains hot after engine stopped for a while. So dont touch the exhaust system and wear clothing which can cover feet completely.

other informations. We recommend you to write down VIN and Engine Number in the spaces given below for you future usage.

TOOLS&INDICATORS LOCATION

VIN: Engine Number: 4

(1) Clutch bar (2) Switch on Left Handle (3) Speedometer (4)Ignition Switch (5) Tachometer (6)Switch on Right Handle (7)Throttle

(8) Front Brake(9)Kick Lever(10) Rear Brake pedal (11) Turning Lock (12) FuelTank switch (13) Gear Shift Lever Main Stand (15) side Stand (14)

Indicators Description Speedometer Speed is indicated with kilometers/hr MileoMeter 5

Can be reset to zero, indicates the distance for a trip in kilometers Turning Indicator Flashes when right or left turning signal is on High beam Indicator Lights when is on position Tachometer Indicates the rotate speed of engine Handle Turning Switch Contra rotated, turning the numbers in Mileometer to zero. Odometer Indicates the distance covered in kilometers in total Neutral Indicator Flashes when in neutral . Fuel Indicator Shows fuel level in the tank

IGNITION SWITHCH
(OFF): All the electric ignition parts are on open circuit. (ON):The circuit is connected and you can start your vehicle. PARK):If you park position, then you can pull your vehicle on the side of road at night, you can turn the key to the shinning. LEFT HANDLE BAR out the key, and the taillight (park light) will keep

. Clutch bar
When you start engine or change gear, control the clutch handle to prevent the rear-wheel from rushing out. Dimmer Switch 6

MAIN PARTS

Change over the switch to

light of

Press the button, the horn will hoot.

headlight goes upward, meanwhile, high beam indicator on instrument panel will light; switch to light of headlight goes downward. Turn signals switch Pull the switch to blinkPull the switch to the left signal light will the left signal light

RIGHT HANDLE BAR

Flameout switch Switch to the electric power is connected, then the engine can be started. Switch to , the electric power was cutter off, it will stop running, and the engine cant be started. WARNING When its fuel lever in fuel tank on

will blink and the indicator light will blink too

WARNING: Please make sure use turn signal lights positionit is time to be refilledAnd then pull while turning or changing lanes. It cannot stop tank switch to position. the automatically, return it to original position after to be . Light switches used, and turn off the signal lights. Switch to headlight will light; switch to light be lightened and switch to in daytime. Electrical starter buttons Press electrical starter switch, the motor running and you can start the engine Front hand brake 7 , instrument light, dimmer light and rear indication NOTICE: In usual situation, the switch must be put on RUNNING position Please don't use this switch unless you want to stop the engine running under urgent situation. . Horn button

When you use the front brake, please grip the hand brake on right handle tightly and slowly. Throttle The throttle is used to adjust the rotate of engine. When you want to accelerate, please turn the handle toward to yourself, otherwise, please turn it backward from yourself. Front brake light switch Press the front hand brake, its taillight will lighten automatically. FUEL TANK SWITCH (OFF): When the switch on the positionthe fuel can not inpour to carburetor from fuel tank. Please turn off the switch when you dont ride the motorcycle. (ON) When the switch on the position the fuel will inpour into carburetor from the main fuel tank. 8

(SAVE): When the switch on the RES position the gasoline in the subsidiary fuel tank will inpour into carburetor from fuel tank

KICK START LEVEL This model has a kick start level on right side of engine. Because of the use of motivate kick start system, when the clutch does not be jointed, the driver can start the engine in any gear level. NOTICE: after start the engine, you must check if the start level returns to its normal position. FUEL TANKE CAP

When open the fuel tank cap, first insert the key and turn to right, then do not pull out the key and draw. When close the fuel tank cap, push hard when the cap pin is in the right position. Then take key out. WARNING: fuel tank can not be excessively filled. It is very dangerous to spatter fuel to the hot engine. WARNING: when refill, the engine should be closed, and turn the start key to off position. And keep away from heat. REAR BRAKE LEVEL When step on the pedal, the rear brake takes effect, and brake light lights. TURNING LOCK To lock turning, you should 9

turn the handle bar to the left. Then insert the start key into the turning lock and turn right. When parking, do not forget to lock it. WARNING: When the turning lock is locked, do not try to push the motor, or you will lose balance.

Gear pedal

shifting

This model has five gears. As the picture shows. When selected one gear speed, the gear pedal returns automatically, so that the next gear level can be easily selected. Step the gear changing pedal down from the idle position; it enters into the low speed level. If without show, the gear changes to the next high speed with every gear CAUTION: when the gear-box is in the idle position, the indicator light lights, its necessary to loosen the clutch level slowly to make sure the gear-box in the idle position.

changing pedal down. If with show, the gear changes to the next low speed with every gear changing pedal up. It can not increase or decrease several gear level once. Before change to low speed level, you should slowdown your motorcycle. Increase the engine rotate speed before joint clutch, and it can prevent the unnecessary abrasion between the transmission chain system and rear tire. HELMET LOCK HOOK The usage of the hook: insert the key and rotate

clockwise, open the hook, next hang the helmet to the hook lock, then pull out key. WARNING: do not drive while the helmet is hanging from helmet hook since it may be dragged inwards and will affect safety driving TOOL BOX The tools in the tool box can be used to repair, to adjustment, to change parts in journey. extend life span of spark plug.

NOTICE OF FUEL AND OIL

FUEL Use the fuel with lead-free or low-lead. Octane should be over 90. Attention: Use the fuel with lead-free or low-lead can 9

OIL
Please use high purity and high performance engine oil, model is SAE10W/40, KEEWAYs black engine oil is your priority.

Running-in

New motorcycle in its first 1000km driving, neither make the engine over-running nor exceed 80% of max. Rotate speed at any gear; do not on the condition of choker full-on; meanwhile, proper gear shifting can avoid overpressure of engine. Driving carefully in running - in period has great help to the service life of new vehicle. Special attention: When running first 300km, please clean the oil filter and re-adjust valve clearance to requirement. Our black oil can last within one year or 5000km, but need check cleanness or even filter oil to continue.

Brake

1)handle bar and brake pedal have free play 2)no brake ineffective 3)no oil leak 1)proper pressure 2)roper tire decoration no rift

Tire

Fuel storage Light indicator Horn and brake switch Engine oil Throttle valve clutch Transmissio n 10

Is there enough fuel for scheming drive? Operate all lights-head light, tail light, brake light, turn signal etc. Distance indicator, gear indicator, turning indicator Well performance Correct oil level 1)throttle tightwire has free play 2)accelerate and close freely 1)tightwire has free play 2)operate smoothly 1)well elasticity 2)proper lubricated

CHECKING BEFORE RIDING

Check following items before riding Check items Handle bar Check key points 1)steady 2)turn flexibly 3)no shaft loose

KEY POINT OF DRIVING

ENGINE START
Check if the switch handles in the position, turn the ignition switch to the indicator will light. CAUTION: Grasp clutch handle tightly to start engine when the shift in neutral position. When engine in cold state: Put wind-block lever of carburetorto full-close A.pull up the right front pedal, kick the starter lever or use electric engine starter. When the engine is started, switch the wind-block lever to B.keep engine starting for a moment to warm-up. Then, switch the wind-block lever into full-open C.Waiting until the engine rotate smoothly; the warm-up for the engine is enough. When the engine is warming enough: Open the accelerator 1/81/4 turn the right front pedal, press starter lever or use electric 11 if shift in neutral position,

starter, the engine is started. When the engine is warm, generally may not use wind-block system. WARNING: We recommend not starting engine in airless or no air facility room. Dont let the engine start when you leave away.

CAUTION: Don't let the engine run too fast when not drive, or itll be too hot and lead to damaging the inside subassembly.

START
Fist handle the clutch tightly, in a flash, step on the gearlever and so it is put into the fist gear. Turn the throttle to the direction of yourslef. At the same time, loosen the clutch slowly and reposefully, the motorcycle will start to go head then. Notice: before starting, please make the side stand come back to the above position, dont make it hanging there. USING THE GEAR SHIFT MECHANISM

The gear shift mechanism could let the engine work reposefully in its natural operating range. The driver should choose one fittest shift commonly. Dont do that slipping the clutch in order to control the speed, its better to slowdown when on the slope in order that the engine can work in its operating range. DRIVING ON THE SLOPE When driving upgrade on the precipitous slope, the motorcycle will start to slowdown and the impetus isnt enough. At that moment should change to a lower gear so that the engine could work in its natural operating range. Shift rapidly in order to avoid losing impetus. When downgrading the slope, the engine should be changed to a lower shift and its easy to brake. Be careful that not let the engines rotate speed too high. USING THE ARRESTER AND PARKING Put clutch to the paddle (the locality of 12

disconnection) before the motorcycle stop, change to neutral gear. Notice the indicator light to make sure if it is neutral gear. NOTICE: The driver who is short of experience always uses rear arrester only, this will lead to accelerated abrasion of the arrester, and prolong the brake distance. WARNING: Only using the front arrester or using the rear arrester only are both very dangerous, for it may arose skidding or being out of control. Using the arrester carefully and gently when on the wet road, other slick road surface and on every swerve. Urgent brake of the arrester is quite dangerous. The motorcycle should be packed on the solid and flat floor. If the motorcycle must be packed on the slope with side stand, change the shift to the first gear to avoid gliding. And turn to neutral gear before start up the engine. Turn the ignition switch to the positionlet the engine flameout. Take off the ignition key from the switch. Turn the oil plug

switch to the position. Lock the steering lock to keep safe. WARNING: The brake stopping distance increases as the increased speed of the cycle. Make sure to keep a safe brake stopping distance between you and the vehicle in front of you.

13

INSPECT AND MAINTENANCE

The following table shows the time limit of regular maintaining under different traveling distance. When every period is over, the inspecting, checkout, lubricating and prescriptive maintain must be done according to the explanation. The system, support of redirector and wheel system are pivotal parts, they need to be checked by skilled workers. We suggest that youd better let the distribute department or qualified worker to inspect and maintain the vehicle. WARNING: Corrected maintenance for the vehicle is must be followed after the new vehicle has run 1000 kilometers. Be sure that the vehicle has been termly and properly maintained according to the specification. CALENDAR FOR MAINTAININGI: inspecting, cleanout, adjusting, lubricating or replacing. C: cleanout Cycle Content Items
*

R: replacing

A: adjusting

L: lubricating Odometer reading km (notice: 2)

maintain mileage remark

1,000km

4,000km

8,000km

12,000km

refer page

Fuel channel

I 14

* *

Furl filter valve Air filter Spark plug notice1

C I C I I I C I I I

C I C R I Per 5000kmR

C I C I I 16 20 14 21 14 C 14 16

* Valve interspace Oil * Oil filter screen * Carburetor idle speeding

mileage remark Drive chain battery Abrasion brake shoe Brake system I of Notice3 1,000km

odograph reading km (notice: 2) 4,000km I I 8,000km I I 12,000km I I pages 1718 15

* * *

brake pipe Font brake oil Brake switch light

Per 1000km:ILA

* I I I 18

headlight Clutch assay

15

Suspend frame

owner who has mechanic license wants to examine

* Nut, bolt, * tire/wheel * * steering *

notice3 notice3

I I I I

I I I I

and repair it by himself, should refer he to

* Need examining and repairing by the distribute department: The vehicles owner should take the eligible tool and the material for inspecting the vehicle with him. If the 1.

the specification.

Need more examining and repairing when driving in the dusty area. If the reading of the odograph is above the numerical value, just repeat the table and continue to examine and repair the vehicle.

***This item, we suggest to be examined and repaired by the distribute department for safe.
NOTICE: The engine shouldnt be cooling and the body should be supported and fixed by the mid-knighthead when exchanging the oil, make sure to discharge the oil quickly and completely. NOTICE: 16

2.

3. If you often drive on the rough road, make sure

to maintain it often in order to keep the vehicles

impregnant.

3. Fix the oil filter screen, spring, the oil filter cover
THE OIL LEVEL AND EXCHANGE THE OIL THE OIL LEVEL Examine the oil level before start the engine. Let the vehicle stand plainly on the floor when examine the oil level, the oil level on the oil dip rod should show between the upper limitand the lower limit Add the coincident oil to the upper limitwhen necessary. EXCHANGE THE OIL AND WASH THE OIL FILTER SCREEN The capability of the engine is 1L 7. 5. 6. 4. and the oil plug. Infuse the engine with coincident oil till to the upper limit. Dont screw the oil hole cover/oil dip rod. Fix the oil hole cover/oil dip rod. Start the engine, after letting the engine work for a few minutes, then shut off the engine. The oil level must achieve to the sign of upper limit, also avoid leaking oil. Fuel oil filter Fuel oil filter is fixed under the oil control bolt. Wash the filter using non-combustible lotion.

1. Unbolt the oil hole cover/oil dip rod, the oil filter
coverand oil plugbefore discharging the oil. Notice: unbolt the oil filter screen and spring after unbolting the oil filter cover. 2. Washing the oil filter screen clean with 17

remove the spark plug.

Spark plug
During the vehicles first 1000 kilometers of journey and later every 4000 kilometers, use metallic brush or spark plug cleaner to clean the deposited char on the spark plug. Please use the special tool to adjust the gap of spark's two electrodes, keep the gap between 0.6mm-0.8mm. The spark plug should be replaced after every 8000 km riding. CAUTION : Do not screw damage the Model of spark plug D8RTC D7RTC D7RTC

BATTARY
For your first time, please follow instruction: Remove the rubber cap of vent, inpour special electrolyte which should between UPPER and LOWER position. Use it after 30 minutes stay for complete chemical function, please assure using the original electrolyte and keep its position. After electrolyte being inpoured, in order to extend battery longevity, please charge for it (this can be done by dealer). Connect wire correctly, red wire with anode (+), black wire with cathode (-), and tighten terminal bolt, please clean the corrosion with metal wire brush during using. The battery and vent pipe should fix steadily to 18

spark screw

plug too tight otherwise thread of cylinder cover. Impurity should not let into engine when

keep it expedite When later normal use, please notice following: Check the electrolytic liquid frequently and keep it near UPPER position which is the best. Frequent start, short driving or in long-time low speed, brake often or install extra electrics will dry the battery faster and shorten service life, please check battery often and add electrolytic liquid or charge. NOTICE: If vehicle driving in the condition of insufficient electrolytic liquid will cause sulfuration and damage battery itself. When check battery and adding distilled water, make sure breather pipe connect battery vent pipe well. Do not press or crook breather pipe or towards other parts to avoid corrosion. Only can adding distilled water (when using battery) 19

to the standard position, add ordinary water will shorten service life of battery. Do not knock or convert battery during dismantle or replace. If connect battery wire in opposite, which will cause damage of wiring system and battery itself. Red wire must with anode (+), black wire with cathode (-). Please turn off electric power (key) when check or replace battery.

ELECTROLYTIC LIQUID:
Battery lies on vehicle side body. Remove side cover, make sure the liquid should stay between the UPPER and LOWER position, then remove the battery cover with a small plastics funnel adding distilled water to its standard position. Warning: Battery may cause exploding gas, beware of the fire source. Battery contains electrolytic liquid, dont spatter on skin or eyes. Electrolytic liquid is poisonous, away from children. According as following when check battery or adding

electrolytic liquid: 1. 2. 3. 4. 5. Turn off the motorcycle electric power. remove the side cover remove the nut and battery cover dismantle cathode then anode take out battery lightly

Idle speed: 1400100r/min (in neutral position)

ADJUSTMENT OF THROTTLE TIGHT WIRE

1. Check if the throttle cable can turn freely from full on to full off position. 2 Measure the free trip in pull buttons flange. The standard free trip should be: 10~ 15. Loose the nut and turn adjustor when adjust free trip.

Do it in opposite order when install battery. CARBURETOR Stable boil off is the basis of good engine performance. Don't adjust the carburetor for its already in best status which you should adjust are: accelerograph tight wire and idle speed. ADJUSTMENT OF CARBURETOR IDLE SPEED Engine must in normal Running temperature when Doing accurate idle adjust. 1. Vehicle vertical to ground, 2. Start engine to warm-up 3. Use the choker screw to adjust idle speed. 20

ADJUSTMENT OF CLUTCH
The free trip of clutch measured from handles terminal before loose of clutch, which should be 1020mm. If theres any abnormal, please adjust as following: (1 )Loosen the lock nut. (2) Screw out or screw in the adjusting screw,

adjusting nut, to make the clutch free journey to reach the demand.(3) Screw tightly the lock nut

weeping degree to 10-20mm. WARNING: the Notice above is the max adjusting distance; actually you should check the chain before every drive. The excess laxity will result in drop of chain, and damage the engine badly. Adjust the chain as the follow

TRANSMISSIOM CHAIN The life of transmission chain depends on proper lubrication and adjustment. The improper maintenance may induce. Excessively abrasion of Transmission chain and the sprocket. When in the Inclement driving chain: Every 1000 driving miles, you should adjust the laxity of the chain as the follow methods, to keep the 21 driving conditions, the frequent maintenance is very necessary. The adjustment of

steps: (1) Support the motorcycle with the main stand. (2) Loosen the rear axes nut. (3) Loosen the lock nut. (4) Rotate the adjusting nut right or left to adjust the laxity degree of the chain. Meanwhile, you should also make sure the center of the front chain and the rear chain in one line Note: when a new chain is fixed, it is necessary to check if the two sprockets are worn. If necessary, the sprocket should be replaced.

You can buy lubricating oil in most of the motorcycle shop; if possible, youd better not choose engine oil or other lubricating oil. Soaking various chains union to make the lubricant to penetrate to the link joint, pin bush and idler wheel. BRAKING This motorcycle adopts disk braking in the front In the periodic check, the follow status is necessary: 1Loosen pin (2) damaging idler wheel (3) drying and rusting chain(4) Wring and griping chain over damage (6) adjust the loosening chain If the chain has the above problems, it will affect the chain wheel also. You should check the chain wheel the following problems: (5) wheel and the rear wheel adopts the drum braking. The correct operation of the braking is very important for your safety driving. Do remember to check the braking system timely, and the checking should be done by some qualified distributors. FRONT WHEEL BRAKING BRAKING OIL CAUTION: The motorcycle uses DOT3 and DOT4 braking oil. It is not allowed to use the leaving oil in the open container and also dont use the leaving oil at last time when you do the mending. Because the leaving oil will 22

1) over damaged chain wheel 2) damaged and broken sprocket 3) loosened fixing screw of chain wheel
LUBIRCATING OF DRIVING CHAIN

absorb the water in the air. Take attention to not splash the braking oil on the surface of paint and plastic, it will corrode their surfaces. Meanwhile, pay attention to check the braking oil in the front braking container. If the oil level falls, please full it with the appointed braking oil. Because when the braking pad is abraded, the leaving oil in the container will infuse the oil pump by itself and the oil level will fall. So supplement the braking oil is one of the most important things during the checking process. BRAKING PADS limiting scale The key is to check if the pads has been 23

abraded to the limiting scale. If exceed the scale, you should change another one. BRAKE SYSTEM WARNING: If the brake system or brake pads need to be maintained, we strongly suggest that you take this work to the dealers, because they have the repairing kit and skill. They will help you deal with the problems with the safest and most economical way. CAUTION: Disk brake system works with way of high pressure. For your safe consideration, you couldnt use the vitta and fluid exceed the stated time as the section of maintenance calendar in the maintenance manual. You couldnt use the front brake handle after you take out the front-wheel. Daily Check: (1) Check the front and rear brake system, so that avoid the fluid may leak. (2) Check the vitta, in order to avoid the fluid may

leak and the vitta has rip. (3) Keep there is a certain spring on the brake handles and brake footplate. (4) Check the abrasion condition of brake pads on front-wheel. WARNING: Dont ride the motorcycle after you change the new disk brake pads at once. Please hold and loosen the handle a few times, let the brake pads stretch enough, renew the spring of handle and make sure the brake fluid cycle steadily.

Abrasion limit of Rear brake There isnt signal of abrasion limit on this rear brake. Please check the situation of abrasion as follow: (1).Check the brake system, make sure the regulation is correct. (2). If the function of brake is well, please check the limit indicative line, make sure it in the allowed range (as the picture A). (3). If the limit indicative line out of the allowed range (as the picture B), you can ask the dealers change the parts of brake to make sure your safe.

REAR BRAKE

When you adjust the journey of rear brake, you can adjust the free journey to 20-30mm by screwing down or loosening the adjusted nut of rear brake. 24

Picture A: The indicative line in the allowed range Picture B: The indicative line out of the allowed range

AIR CLEANER Cleaning air filter must be done periodically , if using motorcycle under dusty or sand and wind conditions should clean be more frequently. Removal 1. Remove the cover of the air filter. 2. Loosen the screws, 1) remove the cover of the air filter 2) take out the air filter. 3. Clean filter with clean dissolvent and let it dry. 4Put filter wick into clean engine oil. 5Fix each part as the opposite sequence of remove it. CAUTION: Gasoline and low burning point dissolvent is the high flammable substance, they must not be use for cleaning.

Change the Headlight bulbs First, remove the adumbral cover, take out the headlight; loosen the screws in the lampshade with screwdriver, take out the lampshade and fix the same specification bulbs instead of the burning headlight bulb, then fix the headlight assembly as the opposite sequence of remove it; finally, install the headlight into its bracket, and install the lampshade. Change the front and rear turning light: 1. Remove the relative turning light from the vehicle. 2. Loosen the screws in turning light with the screwdriver. 3. Remove the shell of turning light, take out the turning bulbs. 4. Change the bulbs with same specification. 5. Install the turning light as the opposite sequence of remove it. 6. Install the turning light which there is a good bulb into the vehicle. 25

CHANGE THE BULBS

NOTICE: When you change the bulbs, please make sure use the same specification, highpower bulbs will add the circuit load, and cause the trouble such as the battery lack of electricity easily. CHANGE FUSE Fuse pipe lie to side of battery, if the fuse be burnt out frequently, its said that there is short circuit or the overmuch circuit load. Please ask the dealers maintain the vehicle in time. WARNING: Use of non-standard fuse may damage the electric system, even damage lights or break out fire, making engine loss its pulling power. It is very dangerous. LUBRICATING POINT Suitable lubricating helps to maintain your motorcycles standard operation, prolong its usage and also helpful for your safety drive. After a long time drive or drenched by rain or cleaning, we recommend lubricate for your motorcycle. The 26

details of lubricating point as follow:

Motorcycle lubricate oil grease Rear Brake Pedal Axes Speedometer Axes Speedometer Gear and Gear Axletree Stand Connection and Spring Hook Stand Axes and Spring Hook Rocker and Camshaft Accelerator Pull Front Hand Brake Axes Clutch Handle NOTICE: Above items with should be operated by specific service technician of our distributors. Side Main Rear Brake

AIR VALVE SPACE ADJUSTMENT Check and adjust valve space when the engine cooled. 1. 2. Remove the peephole cover , engine cover , and cylinder cover . Turn engine rotor to counter-clockwise. Make T point to the center of above peephole, must make sure that the plunger on the top of compress stroke. 3. 4. Insert space test ruler into screw and the valve lever, check the space of in-out air valve. Standard space of in-out air valve: Air inlet stroke: 0.05mm Air outlet Stroke: 0.05mm NOTICE: Adjusting air valve space may directly influence engine performance, we recommend air valve are checked and adjusted strictly at the time in Maintain Timetable. Adjusting air valve space requires specific technical and relative tools. We recommend leave these job to our Distributors or Maintain Service Center for the best adjustment.

5. For adjustment, only need to loose the nut

then turn the screw . Finish adjustment, tight the nut, test the space again till reach the standard. 27

kpa (kgf/cm2)

Driver and a passenger

196(2.0)

221(2.25)

TIRES Suitable tire pressure will keep the best stability, comfortable drive, and long usage of tires. Check tire pressure, and adjust it if necessary. CAUTION: Check tire press before driving and the tire is cooled. Standard pressure Only driver FR TIRE 172(1.75 RR TIRE 196(2.0) WARNING: We recommend not trying to repair tires for the balance of wheel and stability of tire may damage. Non-standard tire inflating may cause abnormal damage for the surface of tire and thread safety drive. Not enough inflating may cause tire slipping or out of wheel, may cause the tire loss air out of control. It is 28

dangerous to drive motorcycle if tires are out of use.

necessary amendment should be down, otherwise, when using it again, amendment questions always be forgot. 1. Change the fuel. 2. Lubricate the drive chain 3. Let the fuel in fuel tank and carburetor Spray the antirust oil inside the fuel tank. Install the

When the deep of veins on tire surface center reaches following amount, tires should be changed to new ones. The minimums of veins depth FR TIRE 1.6 mm RR TIRE 2.0 mm

fuel tank cap on it again. NOTICE: Discharge the fuel in carburetor is the most important if store more than one month, it is necessary for remain its normal performance. Warning: Fuel is easy to burn, and can also blow up under fix condition. Please dont smoke or make any spark nearby when diascharge the fuel. 4.Unlade the spark plug and inject 1 spoon (1520cm3) clean fuel into the cylinder. Step it and start equipment sometimes, to make the fuel to be 29

STORING INSTRUCTION
STORING In order to reduce the influence of the quality reduction, some methods have to take if need a longtime storing. In addition, before the store,

scattered, then installs the spark plug again. NOTICE: when engine is running, the ignition switch should be on the position, In order to avoid damage the ignition system, the saprk plug should be inserted into the cover of cable and connect the ground . 5. Discharge the battery and store it in a place without warming temperature or sunshine directly, check the electrolyte each month and charge it slowly. 6. Clean and dry the motorcycle and created the coated surface. 7. Charge the tire into suggested pressure, put the motor on the pad and make the two tires off the ground. 8. Cover the motorcycle (do not use the plastic or coated material) put it in a place which has little change on temperature, and has no heat or wet air. Dont put the motorcycle directly in the sunshine. After storage; 30

1 Put off the cover and clean the motorcycle, and exchange the engine oil if store for more than four month. 2 Check the electrolyte and charge it if it is necessary then Install battery. 3 Discharge the extra antirust oil from the fuel tank, refuel the oil box with new oil. 4 Check all before start (page 9), test the motorcycle with low speed in safe and beyond the road.

SPECIFICATION AND TECHNICAL PARAMETER SIZE and WEIGHT LENGTH1990mm WIDTH740mm HEIGHT1070mm WHEELBASE1300mm MASS120kg

Forth gear transmission ratio1.130 ENGINE MODEL..single cylinder, four stroke, wind cool ENGINE MODLEQJ157FMI BORESTORKE56.6mm49.5mm EXHAUST124CM3 NOMINAL EXHAUST125CM3 MAX RATIO8kW/8500r/min DEMARCATE RATIO6.5kW/7800r/min IGNITIONCDI COMPRESSION RATIO9:1 START METHODelectrical start and kick start GEAR SHIFT CLUTCH .multi FIVE GEAR SHIFT METHOD First gear transmission ratio2.769 Second gear transmission ratio1.882 Third gear transmission ratio1.400 31 FRAME Front absorberOil damp Rear absorberOil damp Front brakeDisk brake Rear brakeDrum Front tire specification2.75-18 Reart tire specification3.50-16 Implement system Battary12V9AH Generator Tail/Brake Turning ..Flywheel Front head light12V35/35W light12V5/21W signal lamp Fifth gear transmission ratio0.960 Primary gear transmission ratio4.055 Finally gear transmission ratio2.733(41/15)

12V10W Idometer 12V3.4W Neutral gear lamp12V3.4W Far indicator light12V3.4W Turning 12V3.4W Horn specification12V1.5A CAPACITY Tiptop design speed85km/h Slopping Brake power20 distance7m signal indicator light lamp

Fixed Fuel RQ-90

max type

load..150kg

Economical speed oil consumption2L/100km Fixed number of persondriver and one passenger tank11L Storage1.6L Engine 1L 32 oil