ORiNOCO AP-2000 Access Point

User Guide

Copyright
2003-2004 Proxim Corporation. All rights reserved. Covered by one or more of the following U.S. patents: 5,231,634; 5,875,179; 6,006,090; 5,809,060; 6,075,812; 5,077,753. This users guide and the software described in it are copyrighted with all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form by any means without the written permission of Proxim Corporation.

Trademarks
ORiNOCO is a registered trademark, and Proxim, and the Proxim logo are trademarks of Proxim Corporation. All other trademarks mentioned herein are the property of their respective owners.

OpenSSL License Note

This product contains software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http:// www.openssl.org/) and that is subject to the following copyright and conditions: Copyright (c) 1998-2002 The OpenSSL Project. All rights reserved. The names "OpenSSL Toolkit" and "OpenSSL Project" must not be used to refer to, endorse, or promote the products or for any other purpose related to the products without prior written permission. For written permission, please contact [email protected]. THIS SOFTWARE IS PROVIDED BY THE OPENSSL PROJECT AS IS AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OPENSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

ORiNOCO AP-2000 Users Guide Software v2.5.2 P/N 68666 R1 October 2004

Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Introduction to Wireless Networking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Guidelines for Roaming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

IEEE 802.11 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Management and Monitoring Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

HTTP/HTTPS Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Command Line Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 SNMP Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 SNMPv3 Secure Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Product Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5 GHz Antenna Adapter or AP-2000 11a Upgrade Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

AP-2000 with Active Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 AP-2000 with Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 5 GHz or AP-2000 11a Upgrade Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
ScanTool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 ScanTool Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Setup Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Setup Wizard Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Download the Latest Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Setup your TFTP Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Download Updates from your TFTP Server using the Web Interface . . . . . . . . . . . . . . . . . . . 30 Download Updates from your TFTP Server using the CLI Interface . . . . . . . . . . . . . . . . . . . . 31

Additional Hardware Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Installing the AP in a Plenum. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Installing/Removing the Metal Faceplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Active Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 3

Contents
LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Viewing Status Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Logging into the HTTP Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 System Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Performing Advanced Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Configuring the AP Using the HTTP/HTTPS Interface . . . . . . . . . . . . . . . . . . . . . . . . . . 36 System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Dynamic DNS Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Access Point System Naming Convention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
IP Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 DHCP Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Link Integrity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Operational Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Operational Mode Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 8Wireless-A and Wireless-B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Wireless A (802.11a) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Wireless (802.11b) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Wireless (802.11b/g). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Wireless Distribution System (WDS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 IP Access Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Secure Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 SNMP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 HTTP Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 HTTPS Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Telnet Configuration Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Secure Shell (SSH) Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Serial Configuration Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 RADIUS Based Management Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Automatic Configuration (AutoConfig) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Auto Configuration and the CLI Batch File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Hardware Configuration Reset (CHRP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Configuration Reset via Serial Port During Bootup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Configuring Hardware Configuration Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Contents
Procedure to Reset Configuration via the Serial Interface . . . . . . . . . . . . . . . . . . . . . . . . . 63

Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Ethernet Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Static MAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Static MAC Filter Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Advanced. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 TCP/UDP Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Adding TCP/UDP Port Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Editing TCP/UDP Port Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Severity Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Alarm Host Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Syslog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Setting Syslog Event Notifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Configuring Syslog Event Notifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Syslog Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Rogue Access Point Detection (RAD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 RAD Configuration Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Configuring RAD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Spanning Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Storm Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Intra BSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Packet Forwarding (Pkt Fwd) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

QoS (Quality of Service) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 RADIUS Profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

RADIUS Servers per Authentication Mode and per VLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 RADIUS-based VLAN Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 RADIUS Servers Enforcing VLAN Access Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Configuring RADIUS Profiles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Adding or Modifying a RADIUS Server Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 MAC Access Control Via RADIUS Authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 802.1x Authentication using RADIUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 RADIUS Accounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 Session Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

SSID/VLAN/Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Management VLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 VLAN Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 Enabling/Disabling VLAN Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 MAC Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 5

Contents
Configuring MAC Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 Security Profiles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 WEP Encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 802.1x Authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 Wi-Fi Protected Access (WPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 Authentication Protocol Hierarchy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 VLANs and Security Profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Configuring Security Profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Wireless-A and Wireless-B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 Adding or Modifying an SSID/VLAN with VLAN Protocol Disabled . . . . . . . . . . . . . . . . . . 93 Adding or Modifying an SSID/VLAN with VLAN Protocol Enabled . . . . . . . . . . . . . . . . . . . 96 Broadcast SSID and Closed System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

Monitoring the AP-2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100

Logging into the HTTP Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102 ICMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 IP/ARP Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 Learn Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 IAPP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 RADIUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 Station Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Enabling and Viewing Station Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107 Refreshing Station Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107 Description of Station Statistics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

Performing Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109

Logging into the HTTP Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 Introduction to File Transfer via TFTP or HTTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
TFTP File Transfer Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111 HTTP File Transfer Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111 Image Error Checking during File Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111

Update AP via TFTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 Update AP via HTTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 Retrieve File via TFTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 Retrieve File via HTTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 Reboot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119

Contents
Help Link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

Troubleshooting the AP-2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121

Troubleshooting Concepts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 Symptoms and Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Connectivity Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 AP Unit Will Not Boot - No LED Activity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 Serial Link Does Not Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 Ethernet Link Does Not Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 Basic Software Setup and Configuration Problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 Lost AP, Telnet, or SNMP Password. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 Client Computer Cannot Connect. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 AP Has Incorrect IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 HTTP (browser) or Telnet Interface Does Not Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 HTML Help Files Do Not Appear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 Telnet CLI Does Not Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 TFTP Server Does Not Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 Client Connection Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 Client Software Finds No Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 Client PC Card Does Not Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 Intermittent Loss of Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 Client Does Not Receive an IP Address - Cannot Connect to Internet . . . . . . . . . . . . . . 124 VLAN Operation Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 Verifying Proper Operation of the VLAN Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 VLAN Workgroups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 Active Ethernet (AE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 The AP Does Not Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 There Is No Data Link. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 Overload Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

Recovery Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

Reset to Factory Default Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 Forced Reload Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 Download a New Image Using ScanTool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 Download a New Image Using the Bootloader CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 Setting IP Address using Serial Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 Hardware and Software Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 Attaching the Serial Port Cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 Initializing the IP Address using CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129

Related Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

RADIUS Authentication Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 TFTP Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

Contents A Using the Command Line Interface (CLI). . . . . . . . . . . . . . . . . . . . . . . . . . . .132

General Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Prerequisite Skills and Knowledge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132 Notation Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132 Important Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132 Navigation and Special Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133 CLI Error Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133

Command Line Interface (CLI) Variations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133

Bootloader CLI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134

CLI Command Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135

Operational CLI Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 ? (List Commands) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 done, exit, quit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 download . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 passwd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 reboot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 upload. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 Parameter Control Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 show CLI Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 set CLI Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 Configuring Objects that Require Reboot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 set and show Command Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140

Using Tables & User Strings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142

Working with Tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 Using Strings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143

Configuring the AP using CLI commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143

Log into the AP using HyperTerminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 Log into the AP using Telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143

Set Basic Configuration Parameters using CLI Commands . . . . . . . . . . . . . . . . . . . . . 144

Set System Name, Location and Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 Set Static IP Address for the AP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 Change Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 Set Network Names for the Wireless Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 Enable and Configure TX Power Control for the Wireless Interface(s) . . . . . . . . . . . . . . 145 Configure SSID (Network Name) and VLAN Pairs, and Profiles . . . . . . . . . . . . . . . . . . . 145 Download an AP Configuration File from your TFTP Server . . . . . . . . . . . . . . . . . . . . . . 147 Backup your AP Configuration File. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147

Contents
Set up Auto Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147

Other Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147

Configure the AP as a DHCP Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148 Configure the DNS Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148 Maintain Client Connections using Link Integrity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148 Change your Wireless Interface Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148 Set Ethernet Speed and Transmission Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 Set Interface Management Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 Configure Syslog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 Configure Intra BSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 Configure MAC Access Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 Set RADIUS Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153 Set Rogue Access Point Detection (RAD) Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . 155 Set Hardware Configuration Reset Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156 Set VLAN/SSID Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156

CLI Monitoring Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156 Parameter Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156

System Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158 Inventory Management Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159 Network Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159 IP Configuration Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159 DHCP Server Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 Link Integrity Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161 Interface Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162 Wireless Interface Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162 Wireless Interface SSID/VLAN/Profile Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 Ethernet Interface Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 Management Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 Secure Management Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 SNMP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 HTTP (web browser) Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 Telnet Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 Serial Port Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 RADIUS Based Management Access Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168 SSH Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168 Auto Configuration Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 TFTP Server Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 IP Access Table Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 Filtering Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170 Ethernet Protocol Filtering Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170 Static MAC Address Filter Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170

Contents
Proxy ARP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171 IP ARP Filtering Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171 Broadcast Filtering Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171 TCP/UDP Port Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171 Alarms Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172 SNMP Table Host Table Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172 Syslog Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172 Bridge Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173 Spanning Tree Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173 Storm Threshold Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 Intra BSS Subscriber Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 Packet Forwarding Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 Security Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 MAC Access Control Parameter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 RADIUS Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 Rogue Access Point Detection (RAD) Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 Hardware Configuration Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 VLAN/SSID Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 Security Profile Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177 Command Syntax and Examples of Configuring Security Profiles: . . . . . . . . . . . . . . . . . 177 Other Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178 IAPP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178 SpectraLink VoIP Parameters (802.11b and bg Modes Only) . . . . . . . . . . . . . . . . . . . . . 178

CLI Batch File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179

Auto Configuration and the CLI Batch File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179 CLI Batch File Format and Syntax. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179 Sample CLI Batch File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179 Reboot Behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180 CLI Batch File Error Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180

B ASCII Character Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .181 C Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .182

Software Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
Management Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182 Advanced Bridging Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183 Medium Access Control (MAC) Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183 Security Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183 Network Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184 Advanced Wireless Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184

Hardware Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184

Physical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184 10

Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185 Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185 Ethernet Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185 Serial Port Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185 Active Ethernet Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185 HTTP Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185

Radio Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185

802.11a Channel Frequencies. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186 802.11b Channel Frequencies. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187 802.11g Channel Frequencies. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187 Wireless Communication Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188 802.11b . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188 802.11a (5 GHz Upgrade Kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189 802.11a (11a Upgrade Kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189 802.11b/g . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190

D Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .191 E Statement of Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .192

Warranty Coverage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192 Repair or Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
Limitations of Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192 Support Procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192

Other Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193

Search Knowledgebase. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193 Ask a Question or Open an Issue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193 Other Adapter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193

Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .194

Information to the User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
Wireless LAN and your Health. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196 Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196

United States FCC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207 Canada IC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208 Europe Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209 Japan Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211 South Korea Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212 Radio Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213

11

Introduction

Document Conventions Introduction to Wireless Networking IEEE 802.11 Specifications Management and Monitoring Capabilities

Document Conventions
The term, AP, refers to an Access Point. The term, 802.11, is used to describe features that apply to the 802.11a, 802.11b, and 802.11g wireless standards. A Dual-radio AP is an Access Point that includes two radios; it can support one or two IEEE radio standards (depending on the type of radios installed). The AP-2000 is a Dual-radio AP. An 802.11a AP is an Access Point that supports the IEEE 802.11a standard. An 802.11b AP is an Access Point that supports the IEEE 802.11b standard. An 802.11b/g AP is an Access Point that supports the IEEE 802.11g standard. Blue underlined text indicates a link to a topic or Web address. If you are viewing this documentation on your computer, click the blue text to jump to the linked item.

NOTE
A Note indicates important information that helps you make better use of your computer.

CAUTION
A Caution indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

Introduction to Wireless Networking

An AP extends the capability of an existing Ethernet network to devices on a wireless network. Wireless devices can connect to a single Access Point, or they can move between multiple Access Points located within the same vicinity. As wireless clients move from one coverage cell to another, they maintain network connectivity. To determine the best location for an Access Point, Proxim recommends conducting a Site Survey before placing the device in its final location. For information about how to conduct a Site Survey, contact your local reseller. Before an Access Point can be configured for your specific networking requirements, it must first be initialized. See Getting Started for details.

12

Introduction

Figure 1-1

Typical wireless network access infrastructure

Once initialized, the network administrator can configure each unit according to the networks requirements. The AP functions as a wireless network access point to data networks. An AP network provides: Seamless client roaming Easy installation and operation Over-the-air encryption of data High speed network links

To be fully operational, the AP-2000 needs at least one wireless card installed.

Guidelines for Roaming

An AP can only communicate with client devices that support its wireless standard. For example, an 802.11a client cannot communicate with an 802.11b AP and an 802.11b client cannot communicate with an 802.11a AP. However, both 802.11b and 802.11g clients can communicate with an 802.11b/g AP. All Access Points must have the same Network Name to support client roaming. All workstations with an 802.11 client adapter installed must use either a Network Name of any or the same Network Name as the Access Points that they will roam between. If an AP has Closed System enabled, a client must have the same Network Name as the Access Point to communicate (see Interfaces). All Access Points and clients must have the same security settings to communicate. The Access Points cells must overlap to ensure that there are no gaps in coverage and to ensure that the roaming client will always have a connection available. The coverage area of an 802.11b or 802.11b/g AP is larger than the coverage area of an 802.11a AP. The 802.11b and 802.11b/g APs operate in the 2.4 GHz frequency band; the 802.11a AP operates in the 5 GHz band. Products that operate in the 2.4 GHz band offer greater range than products that operate in the 5 GHz band. An 802.11a or 802.11b/g AP operates at faster data rates than the 802.11b AP. 802.11a and 802.11g products operate at speeds of up to 54 Mbits/sec; 802.11b products operate at speeds of up to 11 Mbits/sec. All Access Points in the same vicinity should use a unique, independent Channel. By default, the AP automatically scans for available Channels during boot-up but you can also set the Channel manually (see Interfaces for details). Access Points that use the same Channel should be installed as far away from each other as possible to reduce potential interference.

13

Introduction

IEEE 802.11 Specifications

In 1997, the Institute of Electrical and Electronics Engineers (IEEE) adopted the 802.11 standard for wireless devices operating in the 2.4 GHz frequency band. This standard includes provisions for three radio technologies: direct sequence spread spectrum, frequency hopping spread spectrum, and infrared. Devices that comply with the 802.11 standard operate at a data rate of either 1 or 2 Megabits per second (Mbits/sec). In 1999, the IEEE modified the 802.11 standard to support direct sequence devices that can operate at speeds of up to 11 Mbits/sec. The IEEE ratified this standard as 802.11b. 802.11b devices are backwards compatible with 2.4 GHz 802.11 direct sequence devices (that operate at 1 or 2 Mbits/sec). Available Frequency Channels vary by regulatory domain and/or country. See 802.11b Channel Frequencies for details. Also in 1999, the IEEE modified the 802.11 standard to support devices operating in the 5 GHz frequency band. This standard is referred to as 802.11a. 802.11a devices are not compatible with 2.4 GHz 802.11 or 802.11b devices. 802.11a radios use a radio technology called Orthogonal Frequency Division Multiplexing (OFDM) to achieve data rates of up to 54 Mbits/sec. Available Frequency Channels vary by regulatory domain and/or country. See 802.11a Channel Frequencies for details. In 2003, the IEEE introduced the 802.11g standard. 802.11g devices operate in the 2.4 GHz frequency band using OFDM to achieve data rates of up to 54 Mbits/sec. In addition, 802.11g devices are backwards compatible with 802.11b devices. Available Frequency Channels vary by regulatory domain and/or country. See 802.11g Channel Frequencies for details.

Management and Monitoring Capabilities

There are several management and monitoring interfaces available to the network administrator to configure and manage an AP on the network: HTTP/HTTPS Interface Command Line Interface SNMP Management

HTTP/HTTPS Interface
The HTTP Interface (Web browser Interface) provides easy access to configuration settings and network statistics from any computer on the network. You can access the HTTP Interface over your LAN (switch, hub, etc.), over the Internet, or with a crossover Ethernet cable connected directly to your computers Ethernet Port. HTTPS provides an HTTP connection over a Secure Socket Layer. HTTPS is one of two available secure management options on the AP; the other secure management option is SNMPv3. Enabling HTTPS allows the user to access the AP in a secure fashion using Secure Socket Layer (SSL) over port 443. The AP supports SSLv3 with a 128-bit encryption certificate maintained by the AP for secure communications between the AP and the HTTP client. All communications are encrypted using the server and the client-side certificate. The AP comes pre-installed with all required SSL files: default certificate, private key and SSL Certificate Passphrase installed.

Command Line Interface

The Command Line Interface (CLI) is a text-based configuration utility that supports a set of keyboard commands and parameters to configure and manage an AP. Users enter Command Statements, composed of CLI Commands and their associated parameters. Statements may be issued from the keyboard for real time control, or from scripts that automate configuration. For example, when downloading a file, administrators enter the download CLI Command along with IP Address, file name, and file type parameters. You access the CLI over a HyperTerminal serial connection or via Telnet. During initial configuration, you can use the CLI over a serial port connection to configure an Access Points IP address. When accessing the CLI via Telnet, you can communicate with the Access Point from over your LAN (switch, hub, etc.), from over the Internet, or with a crossover Ethernet cable connected directly to your computers Ethernet Port. See Using the Command Line Interface (CLI) for more information on the CLI and for a list of CLI commands and parameters.

14

Introduction SNMP Management

In addition to the HTTP and the CLI interfaces, you can also manage and configure an AP using the Simple Network Management Protocol (SNMP). Note that this requires an SNMP manager program, like HP Openview or Castlerocks SNMPc. The AP supports several Management Information Base (MIB) files that describe the parameters that can be viewed and/or configured over SNMP: MIB-II (RFC 1213) Bridge MIB (RFC 1493) Ethernet-like MIB (RFC 1643) 802.11 MIB ORiNOCO Enterprise MIB

Proxim provides these MIB files on the CD included with each Access Point. You need to compile one or more of the above MIBs into your SNMP programs database before you can manage an Access Point using SNMP. Refer to the documentation that came with your SNMP manager for instructions on how to compile MIBs. The Enterprise MIB defines the read and read-write objects that can be viewed or configured using SNMP. These objects correspond to most of the settings and statistics that are available with the other management interfaces. Refer to the Enterprise MIB for more information; the MIB can be opened with any text editor, such as Microsoft Word, Notepad, or WordPad.

SNMPv3 Secure Management

SNMPv3 is one of two available secure management options on the AP; the other secure management option is HTTPS (HTTP connection over Secure Socket Layer). SNMPv3 is based on the existing SNMP framework, but addresses security requirements for device and network management. The security threats addressed by Secure Management are: Modification of information: An entity could alter an in-transit message generated by an authorized entity in such a way as to effect unauthorized management operations, including the setting of object values. The essence of this threat is that an unauthorized entity could change any management parameter, including those related to configuration, operations, and accounting Masquerade: Management operations that are not authorized for some entity may be attempted by that entity by assuming the identity of an authorized entity. Message stream modification: SNMP is designed to operate over a connectionless transport protocol. There is a threat that SNMP messages could be reordered, delayed, or replayed (duplicated) to effect unauthorized management operations. For example, a message to reboot a device could be copied and replayed later. Disclosure: An entity could observe exchanges between a manager and an agent and thereby learns the values of managed objects and learn of notifiable events. For example, the observation of a set command that changes passwords would enable an attacker to learn the new passwords. Authentication: Provides data integrity and data origin authentication. Privacy (a.k.a Encryption): Protects against disclosure of message payload. Access Control: Controls and authorizes access to managed objects

To address the security threats listed above, SNMPv3 provides the following when secure management is enabled:

The default SNMPv3 username is administrator, with SHA authentication, and DES privacy protocol.

NOTE
The remainder of this guide describes how to configure an AP using the HTTP Web interface or the CLI interface. For information on how to manage devices using SNMP, refer to the documentation that came with your SNMP program. Also, refer to the MIB files for information on the parameters available via SNMP.

15

Getting Started

Prerequisites Product Package System Requirements Hardware Installation Initialization Download the Latest Software Additional Hardware Features

Prerequisites
Before installing an AP, you need to gather certain network information. The following section identifies the information you need.

NOTE
Passwords must be configured with at least 6 characters in length.
Network Name (SSID of the wireless cards) You must assign the Access Point a Primary Network Name before wireless users can communicate with it. The clients also need the same Network Name. This is not the same as the System Name, which applies only to the Access Point. The network administrator typically provides the Network Name. If you do not have a DHCP server on your network, then you need to assign the Access Point an IP address that is valid on your network. Each Access Point requires a read/write password to access the web interface. The default password is public. Each Access Point requires a read/write password to access the CLI interface. The default password is public. Each Access Point requires a password to allow get requests from an SNMP manager. The default password is public. Each Access Point requires a password to allow get and set requests from an SNMP manager. The default password is public. This password must be at least 6 characters in length. If Secure Management is enabled, each Access Point requires a password for sending authenticated SNMPv3 messages. The default password is public. The default SNMPv3 username is administrator, with SHA authentication, and DES privacy protocol. If Secure Management is enabled, each Access Point requires a password when sending encrypted SNMPv3 data. The default password is public. You need to determine what security features you will enable on the Access Point. A primary authentication server may be configured; a backup authentication server is optional. The network administrator typically provides this information. This is a password shared between the Access Point and the RADIUS authentication server (so both passwords must be the same), and is typically provided by the network administrator. This is a port number (default is 1812) and is typically provided by the network administrator. The Access Point can automatically provide IP addresses to clients as they sign on. The network administrator typically provides the IP Pool range. The network administrator typically provides this IP Address.

APs IP Address HTTP Password CLI Password SNMP Read Password SNMP Read-Write Password

SNMPv3 Authentication Password

SNMPv3 Privacy Password Security Settings Authentication Method Authentication Server Shared Secret

Authentication Server Authentication Port Client IP Address Pool Allocation Scheme DNS Server IP Address

16

Getting Started

Product Package
Each Dual-radio AP comes with the following: One ceiling or wall mounting plate Mounting hardware Metal faceplate for APs mounted in a plenum environment AP cover Processor module (with integrated Active Ethernet, if applicable) Power supply (not provided with Active Ethernet unit) AC power cord (not provided with Active Ethernet unit) 802.11b PC Card or 802.11b/g AP Card One Installation CD-ROM that contains the following: Software Installation Wizard ScanTool Solarwinds TFTP software HTML Help this users guide in PDF format One Access Point Quick Start Guide

If any of these items are missing or damaged, please contact your reseller or Technical Support (see Technical Support for contact information).

5 GHz Antenna Adapter or AP-2000 11a Upgrade Kit

The 5 GHz Antenna Adapter or 11a Upgrade Kit can be used in the Access Point. Because 802.11a requires an antenna adapter, only one 5 GHz radio can be installed in the AP. The second slot can be populated with an 802.11b or 802.11b/g card.

System Requirements
To begin using an AP, you must have the following minimum requirements: A 10Base-T Ethernet or 100Base-TX Fast Ethernet switch or hub At least one radio card designed for the AP: an 802.11b PC Card, 802.11b/g Card, 5 GHz Antenna Adapter Kit, or 11a Upgrade Kit At least one of the following IEEE 802.11-compliant devices: An 802.11a client device if you have an 802.11a AP An 802.11b or 802.11b/g client device if you have an 802.11b AP An 802.11b/g client device if you have an 802.11b/g AP An 802.11a/g client device if you have an 802.11a/g AP A computer that is connected to the same IP network as the AP and has one of the following Web browsers installed: Microsoft Internet Explorer 6 with Service Pack 1 or later and patch Q323308 Netscape 6.1 or later (The computer is required to configure the AP using the HTTP interface.)

17

Getting Started

Hardware Installation
AP-2000 with Active Ethernet AP-2000 with Power Supply 5 GHz or AP-2000 11a Upgrade Kit

AP-2000 with Active Ethernet

1. Slide the AP module onto the mounting bracket. Make sure it is properly seated.

Figure 2-1

Insert Module into Mounting Bracket

2. Slide an 802.11b, 802.11b/g wireless card, or 802.11a card with antenna adapter (not included in the kit) into Slot A or B. NOTE: The 802.11a wireless card with antenna adapter will only fit in Slot A. 3. Slide an 802.11b or an 802.11b/g wireless card (included in the kit) into Slot A or B.

Figure 2-2

Slide a PC Card into the AP

4. Connect power to the unit from a DC injector device, such as the ORiNOCO 1-Port Active Ethernet DC Injector hub. 5. Wait for the LED indicators to turn green before proceeding.

18

Getting Started

Figure 2-3

Connect an Ethernet cable from an AE hub to the AP

6. Conduct a Site Survey to determine the best location for your device. 7. Once you have chosen a final location for your unit, mount the wall bracket and the processor module and place the cover onto the unit as shown.

Figure 2-4

Wall mounting the AP

AP-2000 with Power Supply

1. Clip the power supply into the mounting bracket. 2. Plug the AC power cord into the power supply.

19

Getting Started

Figure 2-5

Install the power supply

3. Slide the AP module onto the mounting bracket. Make sure it is properly seated. 4. Plug the DC connector from the power supply into the top of the AP module.

Figure 2-6

Insert module in mounting bracket and attach power connector

20

Getting Started
Figure 2-7 Slide a PC Card into the AP

5. Attach one end of an Ethernet cable to the AP's Ethernet port and the other end to a network hub or switch. 6. Connect the unit to a power source. 7. Wait for the power LED to turn green before proceeding.

Figure 2-8

Power LED turns green when the unit is operational

8. Conduct a Site Survey to determine the best location for your device. 9. Once you have chosen a final location for your unit, mount the wall bracket and the processor module and place the cover onto the unit as shown.

Figure 2-9

Wall mounting the AP

21

Getting Started 5 GHz or AP-2000 11a Upgrade Kit

If you are installing this kit on a new AP (one that has not been installed yet), skip to Step 4. 1. Remove the AP from your network by unplugging the power and Ethernet cables from the unit. 2. Remove the unit from its mounting location - keep the mounting bracket with the AP. 3. Remove the outer plastic cover.

Figure 2-10

Remove the AP cover

NOTE
The AP-2000 Upgrade Kit may be installed only in slot A of the AP-2000. 4. Make sure card slot A is available. The power or Ethernet cable tie wrap may need to be cut and the cable repositioned to allow the antenna adapter to fit correctly. 5. Position the antenna adapter, card inward, facing the top of the unit (see diagram) and insert the 5 GHz card into the available card slot.

Figure 2-11

Insert Card and Antenna

22

Getting Started
6. Angle the antenna adapter slightly upwards, pinch the end tabs inwards and carefully slide the antenna adapter onto the mounting bracket. 7. Gently push forward while rotating the antenna downwards and clip the adapter into the small cutouts on the face of the mounting bracket. 8. Position the antenna for best reception: at a 90 angle for flat surface mounts at a 180 angle for wall mounts 9. Re-install the cover and mount the AP back in place. 10. Connect the power and Ethernet cables to the AP.

Figure 2-12

Replace cover

23

Getting Started

Initialization
Proxim provides two tools to simplify the initialization and configuration of an AP: ScanTool Setup Wizard

ScanTool is included on the Installation CD; the Setup Wizard launches automatically the first time you access the HTTP interface.

NOTE
These initialization instructions describe how to configure an AP over an Ethernet connection using ScanTool and the HTTP interface. If you want to configure the unit over the serial port, see Setting IP Address using Serial Port for information on how to access the CLI over a serial connection and Using the Command Line Interface (CLI) for a list of supported commands.

ScanTool
ScanTool is a software utility that is included on the installation CD-ROM. ScanTool allows you to find the IP address of an Access Point by referencing the MAC address in a Scan List, or to assign an IP address if one has not been assigned. The tool automatically detects the Access Points installed on your network, regardless of IP address, and lets you configure each units IP settings. In addition, you can use ScanTool to download new software to an AP that does not have a valid software image installed (see Client Connection Problems). To access the HTTP interface and configure the AP, the AP must be assigned an IP address that is valid on its Ethernet network. By default, the AP is configured to obtain an IP address automatically from a network Dynamic Host Configuration Protocol (DHCP) server during boot-up. If your network contains a DHCP server, you can run ScanTool to find out what IP address the AP has been assigned. If your network does not contain a DHCP server, the Access Points IP address defaults to 10.0.0.1. In this case, you can use ScanTool to assign the AP a static IP address that is valid on your network.

ScanTool Instructions
Follow these steps to install ScanTool, initialize the Access Point, and perform initial configuration: 1. Locate the units Ethernet MAC address and write it down for future reference. The MAC address is printed on the product label. Each unit has a unique MAC address, which is assigned at the factory. 2. Confirm that the AP is connected to the same LAN subnet as the computer that you will use to configure the AP. 3. Power up, reboot, or reset the AP. Result: The unit requests an IP Address from the network DHCP server. 4. Insert the Installation CD into the CD-ROM drive of the computer that you will use to configure the AP. Result: The installation program will launch automatically. 5. Follow the on-screen instructions to install the Access Point software and documentation.

NOTE
The ORiNOCO Installation program supports the following operating systems: Windows 98SE Windows 2000 Windows NT Windows ME Windows XP 6. After the software has been installed, double-click the ScanTool icon on the Windows desktop to launch the program (if the program is not already running). Result: ScanTool scans the subnet and displays all detected Access Points. The ScanTools Scan List screen appears, as shown in the following example.

24

Getting Started
NOTE
If your computer has more than one network adapter installed, you will be prompted to select the adapter that you want ScanTool to use before the Scan List appears. If prompted, select an adapter and click OK. You can change your adapter setting at any time by clicking the Select Adapter button on the Scan List screen. Note that the ScanTool Network Adapter Selection screen will not appear if your computer only has one network adapter installed.

Figure 2-13

Scan List

7. Locate the MAC address of the AP you want to initialize within the Scan List.

NOTE
If your Access Point does not show up in the Scan List, click the Rescan button to update the display. If the unit still does not appear in the list, see Troubleshooting the AP-2000 for suggestions. Note that after rebooting an Access Point, it may take up to five minutes for the unit to appear in the Scan List. 8. Do one of the following: If the AP has been assigned an IP address by a DHCP server on the network, write down the IP address and click Cancel to close ScanTool. Proceed to Setup Wizard for information on how to access the HTTP interface using this IP address. If the AP has not been assigned an IP address (in other words, the unit is using its default IP address, 10.0.0.1), follow these steps to assign it a static IP address that is valid on your network: 1. Highlight the entry for the AP you want to configure. 2. Click the Change button. Result: the Change screen appears.

25

Getting Started
Figure 2-14 3. 4. Scan Tool Change Screen Set IP Address Type to Static. Enter a static IP Address for the AP in the field provided. You must assign the unit a unique address that is valid on your IP subnet. Contact your network administrator if you need assistance selecting an IP address for the unit. Enter your networks Subnet Mask in the field provided. Enter your networks Gateway IP Address in the field provided. Enter the SNMP Read/Write password in the Read/Write Password field (for new units, the default SNMP Read/Write password is public).

5. 6. 7.

NOTE
The TFTP Server IP Address and Image File Name fields are only available if ScanTool detects that the AP does not have a valid software image installed. See Client Connection Problems. Click OK to save your changes. Result: The Access Point will reboot automatically and any changes you made will take effect. 9. When prompted, click OK a second time to return to the Scan List screen. 10. Click Cancel to close the ScanTool. 11. Proceed to Setup Wizard for information on how to access the HTTP interface. 8.

Setup Wizard
The first time you connect to an APs HTTP interface, the Setup Wizard launches automatically. The Setup Wizard provides step-by-step instructions for how to configure the Access Points basic operating parameter, such as Network Name, IP parameters, system parameters, and management passwords.

Setup Wizard Instructions

Follow these steps to access the Access Points HTTP interface and launch the Setup Wizard: 1. Open a Web browser on a network computer. The HTTP interface supports the following Web browser: Microsoft Internet Explorer 6 with Service Pack 1 or later Netscape 6.1 or later 2. If necessary, disable the browsers Internet proxy settings. For Internet Explorer users, follow these steps: Select Tools > Internet Options. Click the Connections tab. Click LAN Settings. If necessary, remove the check mark from the Use a proxy server box. Click OK twice to save your changes and return to Internet Explorer. 3. Enter the Access Points IP address in the browsers Address field and press Enter. This is either the dynamic IP address assigned by a network DHCP server or the static IP address you manually configured. See ScanTool for information on how to determine the units IP address and manually configure a new IP address, if necessary. Result: The Enter Network Password screen appears. 4. Enter the HTTP password in the Password field. Leave the User Name field blank. For new units, the default HTTP password is public. Result: The Setup Wizard will launch automatically.

26

Getting Started

Figure 2-15

Enter Network Password

Figure 2-16

Setup Wizard

5. Click Setup Wizard to begin. If you want to configure the AP without using the Setup Wizard, click Exit and see Performing Advanced Configuration. The Setup Wizard supports the following navigation options: Save & Next Button: Each Setup Wizard screen has a Save & Next button. Click this button to submit any changes you made to the units parameters and continue to the next page. The instructions below describe how to navigate the Setup Wizard using the Save & Next buttons. Navigation Panel: The Setup Wizard provides a navigation panel on the left-hand side of the screen. Click the link that corresponds to the parameters you want to configure to be taken to that particular configuration screen. Note that clicking a link in the navigation panel will not submit any changes you made to the units configuration on the current page. Exit: The navigation panel also includes an Exit option. Click this link to close the Setup Wizard at any time.

CAUTION
If you exit from the Setup Wizard, any changes you submitted (by clicking the Save & Next button) up to that point will be saved to the unit but will not take effect until it is rebooted.

6. Configure the System Configuration settings and click Save & Next. See System for more information. 7. Configure the Access Points Basic IP address settings, if necessary, and click Save & Next. See Basic IP Parameters for more information.

27

Getting Started
8. Assign the AP new passwords to prevent unauthorized access and click Save & Next. Each management interface has its own password: SNMP Read Password SNMP Read-Write Password SNMPv3 Authentication Password SNMPv3 Privacy Password CLI Password HTTP (Web) Password By default, each of these passwords is set to public. See Passwords for more information. 9. Configure the basic wireless interface settings and click Save & Next. The following options are available for an 802.11a AP: Primary Network Name (SSID): Enter a Network Name (between 1 and 32 characters long) for the wireless network. You must configure each wireless client to use this name as well. Additional Network Names (SSIDs): The AP supports up to 16 SSIDs and VLANs per wireless interface (radio). Refer to the Advanced Configuration chapter for information on the detailed rules on configuring multiple SSIDs, VLANs, and security modes. Auto Channel Select: By default, the AP scans the area for other Access Points and selects the best available communication channel, either a free channel (if available) or the channel with the least amount of interference. Remove the check mark to disable this option. Note that you cannot disable Auto Channel Select for 802.11a products in Europe (see Dynamic Frequency Selection (DFS) for details). Frequency Channel: When Auto Channel Select is enabled, this field is read-only and displays the Access Points current operating channel. When Auto Channel Select is disabled, you can specify the Access Points channel. If you decide to manually set the units channel, ensure that nearby devices do not use the same frequency. Available Channels vary based on regulatory domain. See 802.11a Channel Frequencies. Note that you cannot manually set the channel for 802.11a products in Europe (see Dynamic Frequency Selection (DFS) for details). Transmit Rate: Use the drop-down menu to select a specific transmit rate for the AP. Choose between 6, 9, 12, 18, 24, 36, 48, 54 Mbits/s, and Auto Fallback. The Auto Fallback feature allows the AP to select the best transmit rate based on the cell size. The following options are available for an 802.11b AP: Primary Network Name (SSID): Enter a Network Name (between 1 and 32 characters long) for the wireless network. You must configure each wireless client to use this name as well. Additional Network Names (SSIDs): The AP supports up to 16 SSIDs and VLANs per wireless interface (radio). Refer to the Advanced Configuration chapter for information on the detailed rules on configuring multiple SSIDs, VLANs, and security modes. Auto Channel Select: By default, the AP scans the area for other Access Points and selects the best available communication channel, either a free channel (if available) or the channel with the least amount of interference. Remove the check mark to disable this option. If you are setting up a Wireless Distribution System (WDS), it must be disabled. See Wireless Distribution System (WDS) for more information. Frequency Channel: When Auto Channel Select is enabled, this field is read-only and displays the Access Points current operating channel. When Auto Channel Select is disabled, you can specify the Access Points operating channel. If you decide to manually set the units channel, ensure that nearby devices do not use the same frequency (unless you are setting up a WDS). Available Channels vary based on regulatory domain. See 802.11b Channel Frequencies. Distance Between APs: Set to Large, Medium, Small, Microcell, or Minicell depending on the site survey for your system. The distance value is related to the Multicast Rate (described next). In general, a larger distance between APs means that your clients operate a slower data rates (on average). This feature is available only if you are using an Orinoco Classic Gold card. See Distance Between APs for more information. Multicast Rate: Sets the rate at which Multicast messages are sent. This value is related to the Distance Between APs parameter (described previously). The table below displays the possible Multicast Rates based on the Distance between APs. This feature is available only if you are using an Orinoco Classic Gold card. See Multicast Rate for more information.

28

Getting Started
Distance between APs Multicast Rate Large Medium Small Minicell Microcell 1 and 2 Mbits/sec 1, 2, and 5.5 Mbits/sec 1, 2, 5.5 and 11 Mbits/sec 1, 2, 5.5 and 11 Mbits/sec 1, 2, 5.5 and 11 Mbits/sec

The following options are available for an 802.11b/g AP: Operational Mode: An 802.11b/g wireless interface can be configured to operate in the following modes: 802.11b mode only 802.11g mode only 802.11g-wifi mode 802.11b/g mode (default) Primary Network Name (SSID): Enter a Network Name (between 1 and 32 characters long) for the wireless network. You must configure each wireless client to use this name as well. Additional Network Names (SSIDs): The AP supports up to 16 SSIDs and VLANs per wireless interface (radio). Refer to the Advanced Configuration chapter for information on the detailed rules on configuring multiple SSIDs, VLANs, and security modes. Auto Channel Select: By default, the AP scans the area for other Access Points and selects the best available communication channel, either a free channel (if available) or the channel with the least amount of interference. Remove the check mark to disable this option. Frequency Channel: When Auto Channel Select is enabled, this field is read-only and displays the Access Points current operating channel. When Auto Channel Select is disabled, you can specify the Access Points channel. If you decide to manually set the units channel, ensure that nearby devices do not use the same frequency. Available Channels vary based on regulatory domain. See 802.11g Channel Frequencies. Transmit Rate: Select a specific transmit rate for the AP. The values available depend on the Operational Mode. Auto Fallback is the default setting; it allows the AP to select the best transmit rate based on the cell size. For 802.11b only -- Auto Fallback, 1, 2, 5.5, 11 Mbits/sec For 802.11g only -- Auto Fallback, 6, 9, 12, 18, 24, 36, 48, 54 Mbits/sec For 802.11b/g and 802.11g-wifi-- Auto Fallback, 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54 Mbits/sec

NOTE
Additional advanced settings are available in the Wireless Interface Configuration screen. See Wireless A (802.11a), Wireless (802.11b), or Wireless (802.11b/g) for details. See SSID/VLAN/Security for more information on security features. 10. Review the configuration summary. If you want to make any additional changes, use the navigation panel on the left-hand side of the screen to return to an earlier screen. After making a change, click Save & Next to save the change and proceed to the next screen. 11. When finished, click Reboot on the Summary screen to restart the AP and apply your changes.

Download the Latest Software

Proxim periodically releases updated software for the AP on its Web site at http://www.proxim.com. Proxim recommends that you check the Web site for the latest updates after you have installed and initialized the unit. Three types of files can be downloaded to the AP from a TFTP server: image (AP software image or kernel) config (configuration file) UpgradeBSPBL (BSP/Bootloader firmware file)

29

Getting Started Setup your TFTP Server

A Trivial File Transfer Protocol (TFTP) server allows you to transfer files across a network. You can upload files from the AP for backup or copying, and you can download the files for configuration and AP Image upgrades. The Solarwinds TFTP server software is located on the ORiNOCO AP Installation CD-ROM. You can also download the latest TFTP software from Solarwinds Web site at http://www.solarwinds.net.

NOTE
If a TFTP server is not available in the network, you can perform similar file transfer operations using the HTTP interface. After the TFTP server is installed: Check to see that TFTP is configured to point to the directory containing the AP Image. Make sure you have the proper TFTP server IP address, the proper AP Image file name, and that the TFTP server is operational. Make sure the TFTP server is configured to both Transmit and Receive files, with no automatic shutdown or time-out.

Download Updates from your TFTP Server using the Web Interface
1. 2. 3. 4. 5. 6. 7. 8. 9. Download the latest software from http://www.proxim.com. Copy the latest software updates to your TFTP server. In the Web Interface, click the Commands button and select the Update AP tab. Enter the IP address of your TFTP server in the field provided. Enter the File Name (including the file extension). Enter the full directory path and file name. If the file is located in the default TFTP directory, you need enter only the file name. Select the File Type from the drop-down menu (use Img for software updates). Select Update AP & Reboot from the File Operation drop-down menu. Click Update. The Access Point will reboot automatically when the download is complete.

30

Getting Started Download Updates from your TFTP Server using the CLI Interface
1. 2. 3. 4. 5. Download the latest software from http://www.proxim.com. Copy the latest software updates to your TFTP server. Open the CLI interface via Telnet or a serial connection. Enter the CLI password when prompted. Enter the command: download <tftpaddr> <filename> img Result: The download will begin. Be patient while the image is downloaded to the Access Point. 6. When the download is complete, type reboot 0 and press Enter.

NOTE
See Using the Command Line Interface (CLI) for more information.

Additional Hardware Features

Installing the AP in a Plenum Active Ethernet LED Indicators

Installing the AP in a Plenum

In an office building, plenum is the space between the structural ceiling and the tile ceiling that is provided to help air circulate. Many companies also use the plenum to house communication equipment and cables. However, these products and cables must comply with certain safety requirements, such as Underwriter Labs (UL) Standard 2043: Standard for Fire Test for Heat and Visible Smoke Release for Discrete Products and Their Accessories Installed in Air-Handling Spaces. The AP has been certified under UL Standard 2043 and can be installed in the plenum only when the following conditions apply: The unit's plastic cover has been removed. The power supply of the Access Point has been removed. There are two 802.11b cards in the cards slots. OR There is one 802.11b card and the other card slot is protected with the metal faceplate provided in your kit.

NOTE
The 5GHz Antenna Adapter Kit or 11a Upgrade Kit is not approved in accordance with UL-2043 for use in a plenum. The Access Point using a power supply, should not be plenum mounted. Use Active Ethernet to power the units mounted in a plenum environment.

Installing/Removing the Metal Faceplate

When using only one card in the Access Point mounted in a plenum environment, remove the plastic cover. Place the top edge of the faceplate under the front ridge of the metal enclosure. Snap the faceplate in the empty card slot in the Access Point.

CAUTION
Do not drop the faceplate into the card slot in the AP.

To install a second radio card, the faceplate must be removed. Gently pry the faceplate off using the tab on the faceplate.

31

Getting Started Active Ethernet

An Active Ethernet-enabled AP is equipped with an 802.3af-compliant Active Ethernet module. Active Ethernet (AE) delivers both data and power to the access point over a single Ethernet cable. If you choose to use Active Ethernet, there is no difference in operation; the only difference is in the power source. The Active Ethernet (AE) integrated module receives ~48 VDC over a standard Category 5 Ethernet cable. To use Active Ethernet, you must have an AE hub (also known as a power injector) connected to the network. The cable length between the AE hub and the Access Point should not exceed 100 meters (approximately 325 feet). The AE hub is not a repeater and does not amplify the Ethernet data signal. If connected to an AE hub and an AC power simultaneously, the Access Point draws power from Active Ethernet. Maximum power supplied to an Access Point is 11 Watts; the unit typically draws approximately 10 Watts.

Also see Hardware Specifications.

NOTE
The APs 802.3af-compliant Active Ethernet module is backwards compatible with all ORiNOCO Active Ethernet hubs that do not support the IEEE 802.3af standard.

LED Indicators
The AP has four LED indicators, which exhibit the following behavior:

Power Green Amber Amber Red n/a n/a Green

Ethernet Green flash with data activity Red n/a (not applicable) Red n/a n/a n/a

PC Card A Green flash with data activity Amber n/a n/a Red Red Amber

PC Card B Green flash with data activity Amber n/a n/a Red Red Amber

Indication Normal Operation Rebooting/Power On Self Test (POST) Missing or bad AP Image if amber after reboot Power On Self Test (POST) running PC Card incompatible on indicated interface PC Card failure on indicated interface Indicated interface in Administrative State. An Amber color on a wireless interface LED indicates that the Wireless Interface Status for the particular wireless interface is Shutdown (refer to Wireless Service Status).

n/a

n/a

Off

Off

PC Card not present

32

Getting Started

Related Topics
The Setup Wizard helps you configure the basic AP settings required to get the unit up and running. The AP supports many other configuration and management options. The remainder of this user guide describes these options in detail. See Performing Advanced Configuration for information on configuration options that are available within the Access Points HTTP interface. See Monitoring the AP-2000 for information on the statistics displayed within the Access Points HTTP interface. See Performing Commands for information on the commands supported by the Access Points HTTP interface. See Troubleshooting the AP-2000 for troubleshooting suggestions. See Using the Command Line Interface (CLI) for information on the CLI interface and for a list of CLI commands.

33

Viewing Status Information

Logging into the HTTP Interface System Status

Logging into the HTTP Interface

Once the AP has a valid IP Address and an Ethernet connection, you may use your web browser to monitor the system status. Follow these steps to monitor an APs operating statistics using the HTTP interface: 1. Open a Web browser on a network computer.

NOTE
The HTTP interface supports the following Web browser: Microsoft Internet Explorer 6 with Service Pack 1 or later Netscape 6.1 or later 2. If necessary, disable the Internet proxy settings. For Internet Explorer users, follow these steps: Select Tools > Internet Options.... Click the Connections tab. Click LAN Settings.... If necessary, remove the check mark from the Use a proxy server box. Click OK twice to save your changes and return to Internet Explorer. 3. Enter the Access Points IP address in the browsers Address field and press Enter. Result: The Enter Network Password screen appears. 4. Enter the HTTP password in the Password field and click OK. Leave the User Name field blank. (By default, the HTTP password is public). Result: The System Status screen appears.

Figure 3-1

Enter Network Password Screen

34

Viewing Status Information

System Status
System Status is the first screen to appear each time you connect to the HTTP interface. You can also return to this screen by clicking the Status button.

Figure 3-2

System Status Screen

Each section of the System Status screen provides the following information: System Status: This area provides system level information, including the units IP address and contact information. See System for information on these settings. System Alarms: System traps (if any) appear in this area. Each trap identifies a specific severity level: Critical, Major, Minor, and Informational. See Alarms for a list of possible alarms.

35

Performing Advanced Configuration

Configuring the AP Using the HTTP/HTTPS Interface System: Configure specific system information such as system name and contact information. Network: Configure IP settings, DNS client, DHCP server, and Link Integrity. Interfaces: Configure the Access Points interfaces: Wireless and Ethernet. Also describes configuring a Wireless Distribution System (WDS). Management: Configure the Access Points management Passwords, IP Access Table, and Services such as configuring secure or restricted access to the AP via SNMPv3, HTTPS, or CLI. Configure Secure Management, SSL, Secure Shell (SSH), and RADIUS Based Access Management. Set up Automatic Configuration for Static IP. Filtering: Configure Ethernet Protocol filters, Static MAC Address filters, Advanced filters, and Port filters. Alarms: Configure the Alarm (SNMP Trap) Groups, the Alarm Host Table, and the Syslog features. Bridge: Configure the Spanning Tree Protocol, Storm Threshold protection, Intra BSS traffic, and Packet Forwarding. RADIUS Profiles: Configure RADIUS features such as RADIUS Access Control and Accounting. SSID/VLAN/Security: Configure security features such as MAC Access Control, WPA, WEP Encryption, and 802.1x. Configure up to 16 VLAN and SSID pairs per wireless interface, and assign Security and RADIUS Profiles for each pair.

Configuring the AP Using the HTTP/HTTPS Interface

Follow these steps to configure an Access Points operating settings using the HTTP/HTTPS interface: 1. Open a Web browser on a network computer.

NOTE
The HTTP interface supports the following Web browser: Microsoft Internet Explorer 6 with Service Pack 1 or later Netscape 6.1 or later 2. If necessary, disable the Internet proxy settings. For Internet Explorer users, follow these steps: Select Tools > Internet Options.... Click the Connections tab. Click LAN Settings.... If necessary, remove the check mark from the Use a proxy server box. Click OK twice to save your changes and return to Internet Explorer. 3. Enter the Access Points IP address in the browsers Address field and press Enter. Result: The Enter Network Password screen appears. 4. Enter the HTTP password in the Password field and click OK. Leave the User Name field blank. (By default, the HTTP password is public). Result: The System Status screen appears.

36

Performing Advanced Configuration

Figure 4-1

Enter Network Password Screen

5. Click the Configure button located on the left-hand side of the screen.

Figure 4-2

Configure Main Screen

6. Click the tab that corresponds to the parameter you want to configure. For example, click Network to configure the Access Points TCP/IP settings. The parameters contained in each of the configuration categories are described later in this chapter. 7. Configure the Access Points parameters as necessary. After changing a configuration value, click OK to save the change. 8. Reboot the Access Point for all of the changes to take effect.

37

Performing Advanced Configuration

System
You can configure and view the following parameters within the System Configuration screen: Name: The name assigned to the AP. System name must be between 1-31 characters. Refer to the Dynamic DNS Support and Access Point System Naming Convention sections for rules on naming the AP. Location: The location where the AP is installed. Location must be between 1-255 characters. Contact Name: The name of the person responsible for the AP. Name must be between 1-255 characters. Contact Email: The email address of the person responsible for the AP. Email must be between 1-255 characters. Contact Phone: The telephone number of the person responsible for the AP. Phone must be between 1-255 characters. Object ID: This is a read-only field that displays the Access Points MIB definition; this information is useful if you are managing the AP using SNMP. Ethernet MAC Address: This is a read-only field that displays the unique MAC (Media Access Control) address for the Access Points Ethernet interface. The MAC address is assigned at the factory. Descriptor: This is a read-only field that reports the Access Points name, serial number, current image software version, and current bootloader software version. Up Time: This is a read-only field that displays how long the Access Point has been running since its last reboot.

Dynamic DNS Support

DNS is a distributed database mapping the user readable names and IP addresses (and more) of every registered system on the Internet. Dynamic DNS is a lightweight mechanism which allows for modification of the DNS data of host systems whose IP addresses change dynamically. Dynamic DNS is usually used in conjunction with DHCP for assigning meaningful names to host systems whose IP addresses change dynamically. Access Points provide DDNS support by adding the host name (option 12) in DHCP Client messages, which is used by the DHCP server to dynamically update the DNS server.

Access Point System Naming Convention

The Access Point's system name is used as its host name. In order to prevent Access Points with default configurations from registering similar host names in DNS, the default system name of the Access Point is uniquely generated. Access Points generate unique system names by appending the last 3 bytes of the Access Point's MAC address to the default system name. The system name must be compliant with the encoding rules for host name as per DNS RFC 1123. The DNS host name encoding rules are: Characters have to be alphanumeric or hyphen. The name cannot start or end with a hyphen. The name cannot start with a digit. The number of characters has to be 63 or less. (Currently the system name length is limited to 32 bytes).

Image upgrades could cause the system to boot with an older system name format that is not DNS compliant. To prevent problems with dynamic DNS after an image upgrade, the system name will automatically be converted to a DNS compliant system name. The rules of conversion of older system names are: If the length is greater than 63 then the string is truncated. (This will not happen since the system name is anyway limited to 31 bytes) All invalid characters at the beginning or end of the string are replaced with the character 'X'. All other invalid characters are replaced with hyphens.

38

Performing Advanced Configuration

Network
The Network tab contains three sub-tabs. IP Configuration DHCP Server Link Integrity

IP Configuration
You can configure and view the following parameters within the IP Configuration screen:

NOTE
You must reboot the Access Point in order for any changes to the Basic IP or DNS Client parameters take effect.

Basic IP Parameters
IP Address Assignment Type: Set this parameter to Dynamic to configure the Access Point as a Dynamic Host Configuration Protocol (DHCP) client; the Access Point will obtain IP settings from a network DHCP server automatically during boot-up. If you do not have a DHCP server or if you want to manually configure the Access Points IP settings, set this parameter to Static. IP Address: The Access Points IP address. When IP Address Assignment Type is set to Dynamic, this field is read-only and reports the units current IP address. The Access Point will default to 10.0.0.1 if it cannot obtain an address from a DHCP server. Subnet Mask: The Access Points subnet mask. When IP Address Assignment Type is set to Dynamic, this field is read-only and reports the units current subnet mask. The subnet mask will default to 255.0.0.0 if the unit cannot obtain one from a DHCP server. Gateway IP Address: The IP address of the Access Points gateway. When IP Address Assignment Type is set to Dynamic, this field is read-only and reports the IP address of the units gateway. The gateway IP address will default to 10.0.0.2 if the unit cannot obtain an address from a DHCP server.

DNS Client
If you prefer to use host names to identify network servers rather than IP addresses, you can configure the AP to act as a Domain Name Service (DNS) client. When this feature is enabled, the Access Point contacts the networks DNS server to translate a host name to the appropriate network IP address. You can use this DNS Client functionality to identify RADIUS servers by host name. See RADIUS Profiles for details. Enable DNS Client: Place a check mark in the box provided to enable DNS client functionality. Note that this option must be enabled before you can configure the other DNS Client parameters. DNS Primary Server IP Address: The IP address of the networks primary DNS server. DNS Secondary Server IP Address: The IP address of a second DNS server on the network. The Access Point will attempt to contact the secondary server if the primary server is unavailable. DNS Client Default Domain Name: The default domain name for the Access Points network (for example, proxim.com). Contact your network administrator if you need assistance setting this parameter.

Advanced
Default TTL (Time to Live): Time to Live (TTL) is a field in an IP packet that specifies how long in seconds the packet can remain active on the network. The Access Point uses the default TTL for packets it generates for which the transport layer protocol does not specify a TTL value. This parameter supports a range from 0 to 65535. By default, TTL is 64.

39

Performing Advanced Configuration DHCP Server

If your network does not have a DHCP Server, you can configure the AP as a DHCP server to assign dynamic IP addresses to Ethernet nodes and wireless clients.

CAUTION
Make sure there are no other DHCP servers on the network and do not enable the DHCP server without checking with your network administrator first, as it could bring down the whole network. Also, the AP must be configured with a static IP address before enabling this feature.

When the DHCP Server functionality is enabled, you can create one or more IP address pools from which to assign addresses to network devices.

Figure 4-3

DHCP Server Configuration Screen

40

Performing Advanced Configuration

You can configure and view the following parameters within the DHCP Server Configuration screen: Enable DHCP Server: Place a check mark in the box provided to enable DHCP Server functionality.

NOTE
You cannot enable the DHCP Server functionality unless there is at least one IP Pool Table Entry configured. Subnet Mask: This field is read-only and reports the Access Points current subnet mask. DHCP clients that receive dynamic addresses from the AP will be assigned this same subnet mask. Gateway IP Address: The AP will assign the specified address to its DHCP clients. Primary DNS IP Address: The AP will assign the specified address to its DHCP clients. Secondary DNS IP Address: The AP will assign the specified address to its DHCP clients. Number of IP Pool Table Entries: This is a read-only field that reports the number of IP address pools currently configured. IP Pool Table Entry: This entry specifies a range of IP addresses that the AP can assign to its wireless clients. The maximum number of entries allowed is 20. Click Add to create a new entry. Click Edit to change an existing entry. Each entry contains the following field: Start IP Address End IP Address Default Lease Time (optional): The default time value for clients to retain the assigned IP address. DHCP automatically renews IP Addresses without client notification. This parameter supports a range between 3600 and 86400 seconds. The default is 86400 seconds. Maximum Lease Time (optional): The maximum time value for clients to retain the assigned IP address. DHCP automatically renews IP Addresses without client notification. This parameter supports a range between 3600 and 86400 seconds. The default is 86400 seconds. Comment (optional) Status: IP Pools are enabled upon entry in the table. You can also disable or delete entries by changing this fields value.

NOTE
You must reboot the Access Point before changes to any of these DHCP server parameters take effect.

Link Integrity
The Link Integrity feature checks the link between the AP and the nodes on the Ethernet backbone. These nodes are listed by IP address in the Link Integrity IP Address Table. The AP periodically pings the nodes listed within the table. If the AP loses network connectivity (that is, the ping attempts fail), the AP disables its wireless interface until the connection is restored. This forces the units wireless clients to switch to another Access Point that still has a network connection. Note that this feature does not affect WDS links (if applicable). You can configure and view the following parameters within the Link Integrity Configuration screen: Enable Link Integrity: Place a check mark in the box provided to enable Link Integrity. Poll Interval (milliseconds): The interval between link integrity checks. Range is 500 - 15000 ms in increments of 500 ms; default is 500 ms. Poll Retransmissions: The number of times a poll should be retransmitted before the link is considered down. Range is 0 to 255; default is 5. Target IP Address Entry: This entry specifies the IP address of a host on the network that the AP will periodically poll to confirm connectivity. The table can hold up to five entries. By default, all five entries are set to 0.0.0.0. Click Edit to update one or more entries. Each entry contains the following field: Target IP Address Comment (optional) Status: Set this field to Enable to specify that the Access Point should poll this device. You can also disable an entry by changing this fields value to Disable.

41

Performing Advanced Configuration

Figure 4-4

Link Integrity Configuration Screen

Interfaces
The Interfaces tab contains the following sub-tabs: Operational Mode 8Wireless-A and Wireless-B Ethernet

From these sub-tabs, you configure the Access Points operational mode, wireless interface settings and Ethernet settings. You may also configure a Wireless Distribution System (WDS) for AP-to-AP communications. For the wireless interface configuration, refer to the wireless parameters below that correspond to your radio type. Wireless A (802.11a) Wireless (802.11b) Wireless (802.11b/g)

42

Performing Advanced Configuration Operational Mode

Operational Mode Selection
You can configure and view the following parameters within the Operational Mode screen. Operational Mode: the mode of communication between the wireless clients and the Access Point: 802.11b only 802.11g only 802.11bg 802.11a 802.11g-wifi 9. Select the transmit power level for interface B from the Wireless-B: Transmit Power Level drop-down menu.

Wireless-A and Wireless-B

Wireless A (802.11a)
You can configure and view the following parameters within the Wireless Interface Configuration screen for an 802.11a AP:

NOTE
You must reboot the Access Point before any changes to these parameters take effect. Physical Interface Type: For an 802.11a AP, this field reports: 802.11a (OFDM 5 GHz). OFDM stands for Orthogonal Frequency Division Multiplexing; this is the name for the radio technology used by 802.11a devices. MAC Address: This is a read-only field that displays the unique MAC (Media Access Control) address for the Access Points wireless interface. The MAC address is assigned at the factory. Regulatory Domain: Reports the regulatory domain for which the AP is certified. Not all features or channels are available in all countries. The available regulatory domains include: FCC - U.S./Canada, Mexico, and Australia ETSI - Europe and the United Kingdom TELEC: Japan SG: Singapore ASIA: China, Hong Kong, and South Korea TW: Taiwan Network Name (SSID): Enter a Network Name (between 1 and 32 characters long) for the wireless network. You must configure each wireless client to use this name as well. Auto Channel Select: The AP scans the area for other Access Points and selects a free or relatively unused communication channel. This helps prevent interference problems and increases network performance. By default this feature is enabled. See 802.11a Channel Frequencies for a list of Channels.

NOTE
You cannot disable Auto Channel Select for 802.11a products in Europe (see Dynamic Frequency Selection (DFS) for details). Frequency Channel: When Auto Channel Select is enabled, this field is read-only and displays the Access Points current operating Channel. When Auto Channel Select is disabled, you can specify the Access Points channel. If you decide to manually set the units Channel, ensure that nearby devices do not use the same frequency. Available Channels vary based on regulatory domain. See 802.11a Channel Frequencies. Note that you cannot manually set the channel for 802.11a products in Europe (see Dynamic Frequency Selection (DFS) for details). Transmit Rate: Use the drop-down menu to select a specific transmit rate for the AP. Choose a particular rate available for protocol being used or Auto Fallback. Auto Fallback is the default setting; it allows the AP unit to select the best transmit rate based on the cell size. DTIM Period: The Deferred Traffic Indicator Map (DTIM) is used with clients that have power management enabled. DTIM should be left at 1, the default value, if any clients have power management enabled. This parameter supports a range between 1 and 255.

43

Performing Advanced Configuration

RTS/CTS Medium Reservation: This parameter affects message flow control and should not be changed under normal circumstances. Range is 0 to 2347. When set to a value between 0 and 2347, the Access Point uses the RTS/CTS mechanism for packets that are the specified size or greater. When set to 2347 (the default setting), RTS/CTS is disabled. See RTS/CTS Medium Reservation for more information. Closed System: Check this box to allow only clients configured with the Access Points specific Network Name to associate with the Access Point. When enabled, a client configured with the Network Name ANY cannot connect to the AP. This option is disabled by default. See Broadcast SSID and Closed System for more information. Wireless Service Status: Select shutdown to shutdown the wireless service on a wireless interface, or resume to resume wireless service. See Wireless Service Status for more information.

Dynamic Frequency Selection (DFS)

802.11a APs sold in Europe use a technique called Dynamic Frequency Selection (DFS) to automatically select an operating channel. During boot-up, the AP scans the available frequency and selects a channel that is free of interference. If the AP subsequently detects interference on its channel, it automatically reboots and selects another channel that is free of interference. DFS only applies to 802.11a APs used in Europe (i.e., units whose regulatory domain is set to ETSI). The European Telecommunications Standard Institute (ETSI) requires that 802.11a devices use DFS to prevent interference with radar systems and other devices that already occupy the 5 GHz band. If you are using an 802.11a AP in Europe, keep in mind the following: DFS is not a configurable parameter. It is always enabled and cannot be disabled. You cannot manually select the devices operating channel; you must let DFS select the channel. You cannot configure the Auto Channel Select option. Within the HTTP interface, this option always appears enabled.

RTS/CTS Medium Reservation

The 802.11 standard supports optional RTS/CTS communication based on packet size. Without RTS/CTS, a sending radio listens to see if another radio is already using the medium before transmitting a data packet. If the medium is free, the sending radio transmits its packet. However, there is no guarantee that another radio is not transmitting a packet at the same time, causing a collision. This typically occurs when there are hidden nodes (clients that can communicate with the Access Point but are out of range of each other) in very large cells. When RTS/CTS occurs, the sending radio first transmits a Request to Send (RTS) packet to confirm that the medium is clear. When the receiving radio successfully receives the RTS packet, it transmits back a Clear to Send (CTS) packet to the sending radio. When the sending radio receives the CTS packet, it sends the data packet to the receiving radio. The RTS and CTS packets contain a reservation time to notify other radios (including hidden nodes) that the medium is in use for a specified period. This helps to minimize collisions. While RTS/CTS adds overhead to the radio network, it is particularly useful for large packets that take longer to resend after a collision occurs. RTS/CTS Medium Reservation is an advanced parameter and supports a range between 0 and 2347 bytes. When set to 2347 (the default setting), the RTS/CTS mechanism is disabled. When set to 0, the RTS/CTS mechanism is used for all packets. When set to a value between 0 and 2347, the Access Point uses the RTS/CTS mechanism for packets that are the specified size or greater. You should not need to enable this parameter for most networks unless you suspect that the wireless cell contains hidden nodes.

Wireless Service Status

The user can shutdown (or resume) the wireless service on the wireless interface of the AP through the CLI, HTTP, or SNMP interface. When the wireless service on a wireless interface is shutdown, the AP will: Stop the AP services to wireless clients connected on that wireless interface by disassociating them Disable the associated BSS ports on that interface Disable the transmission and reception of frames on that interface Indicate the wireless service shutdown status of the wireless interface through LED and traps Enable Ethernet interface so that it can receive a wireless service resume command through CLI/HTTP/SNMP interface

NOTE
WSS disables only BSS ports; WDS ports are still operational.

44

Performing Advanced Configuration

In shutdown state, AP will not transmit and receive frames from the wireless interface and will stop transmitting periodic beacons. Moreover, none of the frames received from the Ethernet interface will be forwarded to that wireless interface. Wireless service on a wireless interface of the AP can be resumed through CLI/HTTP/SNMP management interface. When wireless service on a wireless interface is resumed, the AP will: Enable the transmission and reception of frames on that wireless interface Enable the associated BSS port on that interface Start the AP services to wireless clients Indicate the wireless service resume status of the wireless interface through LED and traps

After wireless service resumes, the AP resumes beaconing, transmitting and receiving frames to/from the wireless interface and bridging the frames between the Ethernet and the wireless interface.

Traps Generated During Wireless Service Shutdown (and Resume)

The following traps are generated during wireless service shutdown and resume, and are also sent to any configured Syslog server. When the wireless service is shutdown on a wireless interface, the AP generates a trap called oriTrapWirelessServiceShutdown. When the wireless service is resumed on a wireless interface, the AP generate a trap called oriTrapWirelessServiceResumed.

NOTE
Wireless service can be shutdown/resumed on each wireless interface individually.

Wireless Interface Activity LED and Wireless Service Shutdown

When the wireless service is shutdown on a wireless interface, the Wireless Interface Activity LED for that interface changes to an amber color. When wireless service is resumed on a wireless interface, the Wireless Interface Activity LED for that interface maintains an OFF state while there is no wireless link activity and changes to green color when there is wireless link activity.

Wireless (802.11b)
You can configure and view the following parameters within the Wireless Interface Configuration screen for an 802.11b AP:

NOTE
You must reboot the Access Point before any changes to these parameters take effect. Physical Interface Type: For 802.11b AP, this field reports: 802.11b (DSSS 2.4 GHz). DSSS stands for Direct Sequence Spread Spectrum; this is the name for the radio technology used by 802.11b devices. MAC Address: This is a read-only field that displays the unique MAC (Media Access Control) address for the Access Points wireless interface. The MAC address is assigned at the factory. Regulatory Domain: Reports the regulatory domain for which the AP is certified. Not all features or channels are available in all countries. The available regulatory domains include: FCC - U.S./Canada, Mexico, and Australia ETSI - Most of Europe, including the United Kingdom, Ireland, Singapore, and Hong Kong TELEC: Japan IL - Israel Network Name (SSID): Enter a Network Name (between 1 and 32 characters long) for the wireless network. You must configure each wireless client to use this name as well. Auto Channel Select: The AP scans the area for other Access Points and selects a free or relatively unused communication channel. This helps prevent interference problems and increases network performance. By default this feature is enabled; see 802.11b Channel Frequencies for a list of Channels. However, if you are setting up a Wireless Distribution System (WDS), it must be disabled. See Wireless Distribution System (WDS) for more information.

45

Performing Advanced Configuration

Frequency Channel: When Auto Channel Select is enabled, this field is read-only and displays the Access Points current operating channel. When Auto Channel Select is disabled, you can specify the Access Points operating channel. If you decide to manually set the units channel, ensure that nearby devices do not use the same frequency (unless you are setting up a WDS). Available Channels vary based on regulatory domain. See 802.11b Channel Frequencies. Distance Between APs: Set to Large, Medium, Small, Microcell, or Minicell depending on the site survey for your system. By default, this parameter is set to Large. The distance value is related to the Multicast Rate (described next). In general, a larger distance between APs means that your clients operate a slower data rates (on average). This feature is available only if you are using an Orinoco Classic Gold card. See Distance Between APs for more information. Multicast Rate: Sets the rate at which Multicast messages are sent. This value is related to the Distance Between APs parameter (described previously). The table below displays the possible Multicast Rates based on the Distance between APs setting. By default, this parameter is set to 2 Mbits/sec. This feature is available only if you are using an Orinoco Classic Gold card. See Multicast Rate for more information.
Distance between APs Multicast Rate Large Medium Small Minicell Microcell 1 and 2 Mbits/sec 1, 2, and 5.5 Mbits/sec 1, 2, 5.5 and 11 Mbits/sec 1, 2, 5.5 and 11 Mbits/sec 1, 2, 5.5 and 11 Mbits/sec

DTIM Period: The Deferred Traffic Indicator Map (DTIM) is used with clients that have power management enabled. DTIM should be left at 1, the default value, if any clients have power management enabled. This parameter supports a range between 1 and 255. RTS/CTS Medium Reservation: This parameter affects message flow control and should not be changed under normal circumstances. Range is 0 to 2347. When set to a value between 0 and 2347, the Access Point uses the RTS/CTS mechanism for packets that are the specified size or greater. When set to 2347 (the default setting), RTS/CTS is disabled. See RTS/CTS Medium Reservation for more information. Interference Robustness: Enable this option if other electrical devices in the 2.4 GHz frequency band (such as a microwave oven or a cordless phone) may be interfering with the wireless signal. The AP will automatically fragment large packets into multiple smaller packets when interference is detected to increase the likelihood that the messages will be received in the presence of interference. The receiving radio reassembles the original packet once all fragments have been received. This feature is available only if you are using an Orinoco Classic Gold card. This option is disabled by default. Closed System: Check this box to allow only clients configured with the Access Points specific Network Name to associate with the Access Point. When enabled, a client configured with the Network Name ANY cannot connect to the AP. This option is disabled by default. See Broadcast SSID and Closed System for more information. Wireless Service Status: Select shutdown to shutdown the wireless service on a wireless interface, or resume to resume wireless service. See Wireless Service Status for more information. Load Balancing: Enable this option so clients can evaluate which Access Point to associate with, based on current AP loads. This feature is enabled by default; it helps distribute the wireless load between APs. This feature is not available if you are using an ORiNOCO ComboCard or a non-ORiNOCO client with the AP. Medium Density Distribution: When enabled, the Access Point automatically notifies wireless clients of its Distance Between APs, Interference Robustness, and RTS/CTS Medium Reservation settings. This feature is enabled by default and allows clients to automatically adopt the values used by its current Access Point (even if these values differ from the clients default values or from the values supported by other Access Points). Note that this feature is available only if you are using an Orinoco Classic Gold card. Proxim recommends that you leave this parameter enabled, particularly if you have ORiNOCO clients on your wireless network (leaving this parameter enabled should not adversely affect the performance of any ORiNOCO ComboCards or non-ORiNOCO cards on your network).

Distance Between APs

Distance Between APs defines how far apart (physically) your AP devices are located, which in turn determines the size of your cell. Cells of different sizes have different capacities and, therefore, suit different applications. For instance, a typical office has many stations that require high bandwidth for complex, high-speed data processing. In contrast, a typical warehouse has a few forklifts requiring low bandwidth for simple transactions.

46

Performing Advanced Configuration

NOTE
This feature is available only if you are using an Orinoco Classic Gold card. Cell capacities are compared in the following table, which shows that small cells suit most offices and large cells suit most warehouses:
Small Cell Physically accommodates few stations High cell bandwidth per station High transmit rate Large Cell Physically accommodates many stations Lower cell bandwidth per station Lower transmit rate

Coverage
The number of Access Points in a set area determines the network coverage for that area. A large number of Access Points covering a small area is a high-density cell. A few Access Points, or even a single unit, covering the same small area would result in a low-density cell, even though in both cases the actual area did not change only the number of Access Points covering the area changed. In a typical office, a high density area consists of a number of Access Points installed every 20 feet and each Access Point generates a small radio cell with a diameter of about 10 feet. In contrast, a typical warehouse might have a low density area consisting of large cells (with a diameter of about 90 feet) and Access Points installed every 200 feet.

Figure 4-5

Low Density vs. Ultra High Density Network

The Distance Between Cells parameter supports five values: Large, Medium, Small, Minicell, and Microcell.

CAUTION
The distance between APs should not be approximated. It is calculated by means of a manual Site Survey, in which an AP is set up and clients are tested throughout the area to determine signal strength and coverage, and local limits such as physical interference are investigated. From these measurements the appropriate cell size and density is determined, and the optimum distance between APs is calculated to suit your particular business requirements. Contact your reseller for information on how to conduct a Site Survey.

Multicast Rate
The multicast rate determines the rate at which broadcast and multicast packets are transmitted by the Access Point to the wireless network. Stations that are closer to the Access Point can receive multicast packets at a faster data rate than stations that are farther away from the AP. Therefore, you should set the Multicast Rate based on the size of the Access Points cell. For example, if the Access Points cell is very small (e.g., Distance Between APs is set to Microcell), you can expect that all stations should be able to successfully receive multicast packets at 11 MBits/sec so you can set Multicast Rate to 11 Mbits/sec. However, if the Access Points cell is large, you need to accommodate

47

Performing Advanced Configuration

stations that may not be able to receive multicast packets at the higher rates; in this case, you should set Multicast Rate to 1 or 2 Mbits/sec.

Figure 4-6

1 Mbits/s and 11 Mbits/s Multicast Rates

NOTE
There is an inter-dependent relationship between the Distance between APs and the Multicast Rate. In general, larger systems operate at a lower average transmit rate. The variation between Multicast Rate and Distance Between APs is presented in the following table:
1.0 Mbit/s Large Medium Small Minicell Microcell yes yes yes yes yes 2.0 Mbits/s yes yes yes yes yes yes yes yes yes yes yes yes 5.5 Mbits/s 11 Mbits/s

The Distance Between APs must be set before the Multicast Rate, because when you select the Distance Between APs, the appropriate range of Multicast values automatically populates the drop-down menu. This feature is not available if you are using an ORiNOCO ComboCard or a non-ORiNOCO client with the AP.

Wireless (802.11b/g)
You can configure the following radio parameters for an 802.11b/g AP:

NOTE
You must reboot the Access Point before any changes to these parameters take effect. Operational Mode: An 802.11b/g wireless interface can be configured to operate in the following modes: 802.11b mode only: The radio uses the 802.11b standard only. 802.11g mode only: The radio is optimized to communicate with 802.11g devices. This setting will provide the best results if this radio interface will only communicate with 802.11g devices.

48

Performing Advanced Configuration

802.11b/g mode: This is the default mode. Use this mode if you want to support a mix of 802.11b and 802.11g devices. 802.11g-wifi: This mode was developed for Wi-Fi compliance testing purposes. It is similar to 802.11g only mode. In general, you should use either 802.11g only mode (if you want to support 802.11g devices only) or 802.11b/g mode to support a mix of 802.11b and 802.11g devices.

Physical Interface Type: Depending on the Operational Mode, this field reports: For 802.11b mode only: "802.11b (CCK/DSSS 2.4 GHz)" For 802.11g and 802.11g-wifi modes: "802.11g (OFDM/DSSS 2.4 GHz)" For 802.11b/g mode: "802.11b/g (ERP-CCK/DSSS/OFDM 2.4 GHz)" OFDM stands for Orthogonal Frequency Division Multiplexing; this is the name for the radio technology used by 802.11a devices. DSSS stands for Direct Sequence Spread Spectrum; this is the name for the radio technology used by 802.11b devices. MAC Address: This is a read-only field that displays the unique MAC (Media Access Control) address for the Access Points wireless interface. The MAC address is assigned at the factory. Regulatory Domain: Reports the regulatory domain for which the AP is certified. Not all features or channels are available in all countries. The available regulatory domains include: FCC - U.S./Canada, Mexico, and Australia ETSI - Europe, including the United Kingdom, China, and South Korea TELEC - Japan IL - Israel Network Name (SSID): Enter a Network Name (between 1 and 32 characters long) for the wireless network. You must configure each wireless client to use this name as well. Auto Channel Select: The AP scans the area for other Access Points and selects a free or relatively unused communication channel. This helps prevent interference problems and increases network performance. By default this feature is enabled; see 802.11g Channel Frequencies for a list of Channels. Frequency Channel: When Auto Channel Select is enabled, this field is read-only and displays the Access Points current operating channel. When Auto Channel Select is disabled, you can specify the Access Points operating channel. If you decide to manually set the units channel, ensure that nearby devices do not use the same frequency (unless you are setting up a WDS). Available Channels vary based on regulatory domain. See 802.11g Channel Frequencies. Transmit Rate: Select a specific transmit rate for the AP. The values available depend on the Operational Mode. Auto Fallback is the default setting; it allows the AP to select the best transmit rate based on the cell size. For 802.11b only -- Auto Fallback, 1, 2, 5.5, 11 Mbits/sec For 802.11g only -- Auto Fallback, 6, 9, 12, 18, 24, 36, 48, 54 Mbits/sec For 802.11b/g and 802.11g-wifi -- Auto Fallback, 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54 Mbits/sec DTIM Period: The Deferred Traffic Indicator Map (DTIM) is used with clients that have power management enabled. DTIM should be left at 1, the default value, if any clients have power management enabled. This parameter supports a range between 1 and 255. RTS/CTS Medium Reservation: This parameter affects message flow control and should not be changed under normal circumstances. Range is 0 to 2347. When set to a value between 0 and 2347, the Access Point uses the RTS/CTS mechanism for packets that are the specified size or greater. When set to 2347 (the default setting), RTS/CTS is disabled. See RTS/CTS Medium Reservation for more information. Closed System: Check this box to allow only clients configured with the Access Points specific Network Name to associate with the Access Point. When enabled, a client configured with the Network Name "ANY cannot connect to the AP. This option is disabled by default. See Broadcast SSID and Closed System for more information.

Wireless Distribution System (WDS)

A Wireless Distribution System (WDS) creates a link between two 802.11a, 802.11b, or 802.11b/g APs over their radio interfaces. This link relays traffic from one AP that does not have Ethernet connectivity to a second AP that has Ethernet connectivity. WDS allows you to configure up to six (6) point-to-point links between Access Points. In the WDS Example below, AP 1 and AP 2 communicate over a WDS link (represented by the blue line). This link provides Client 1 with access to network resources even though AP 1 is not directly connected to the Ethernet network. Packets destined for or sent by the client are relayed between the Access Points over the WDS link.

49

Performing Advanced Configuration

Figure 4-7

WDS Example

Bridging WDS
Each WDS link is mapped to a logical WDS port on the AP. WDS ports behave like Ethernet ports rather than like standard wireless interfaces: on a BSS port, an Access Point learns by association and from frames; on a WDS or Ethernet port, an Access Point learns from frames only. When setting up a WDS, keep in mind the following: The WDS link shares the communication bandwidth with the clients. Therefore, while the maximum data rate for the Access Points cell is still 11 Mb, client throughput will decrease when the WDS link is active. If there is no partner MAC address configured in the WDS table, the WDS port remains disabled. Each WDS port on a single AP should have a unique partner MAC address. Do not enter the same MAC address twice in an APs WDS port list. Each Access Point that is a member of the WDS must have the same Channel setting to communicate with each other. Each Access Point that is a member of the WDS must have the same network domain. Each Access Point that is a member of the WDS must have the same WEP Encryption settings. WDS does not use 802.1x. Therefore, if you want to encrypt the WDS link, you must configure each Access Point to use WEP encryption, and each Access Point must have the same Encryption Key(s). See SSID/VLAN/Security. If your network does not support spanning tree, be careful to avoid creating network loops between APs. For example, creating a WDS link between two Access Points connected to the same Ethernet network will create a network loop (if spanning tree is disabled). For more information, refer to the Spanning Tree section.

WDS Setup Procedure NOTE

You must disable Auto Channel Select to create a WDS. Each Access Point that is a member of the WDS must have the same Channel setting to communicate with each other.

NOTE
For radio cards that belong to the ETSI regulatory domain, ACS is enabled by default, and cannot be disabled. Therefore, it is not possible to set up a WDS link. This only applies to ETSI 802.11a wireless radios. To setup a wireless backbone follow the steps below for each AP that you wish to include in the Wireless Distribution System.

50

Performing Advanced Configuration

1. 2. 3. 4. 5. Confirm that Auto Channel Select is disabled. Write down the MAC Address of the radio that you wish to include in the Wireless Distribution System. Click on Interfaces > Wireless-A or Wireless-B. Scroll down to the Wireless Distribution System heading. Click the Edit button to update the Wireless Distribution System (WDS) Table (see Figure 4-8).

Figure 4-8

WDS Edit Entry Screen

The WDS Configuration screen will be displayed (see Figure 4-9).

Figure 4-9

WDS Configuration Screen

6. If desired, enable security by checking the Enable WDS Security Mode box.

51

Performing Advanced Configuration

7. If security mode is enabled, enter a value for Encryption Key 0. 8. Click OK. 9. Enter the MAC Address that you wrote down in Step 2 in one of the Partner MAC Address field of the Wireless Distribution Setup window. 10. Set the Status of the device to Enable. 11. Click OK. 12. Reboot the AP.

Ethernet
Select the desired speed and transmission mode from the drop-down menu. Half-duplex means that only one side can transmit at a time and full-duplex allows both sides to transmit. When set to auto-duplex, the AP negotiates with its switch or hub to automatically select the highest throughput option supported by both sides. For best results, Proxim recommends that you configure the Ethernet setting to match the speed and transmission mode of the device the Access Point is connected to (such as a hub or switch). If in doubt, leave this setting at its default, auto-speed-auto-duplex. Choose between: 10 Mbit/s - half duplex, full duplex, or auto duplex 100 Mbit/s - half duplex or full duplex auto speed - half duplex or auto duplex

52

Performing Advanced Configuration

Management
The Management tab contains five sub-tabs. Passwords IP Access Table Services Automatic Configuration (AutoConfig) Hardware Configuration Reset (CHRP)

Passwords
The following passwords are configurable: SNMP Read Community Password: The password for read access to the AP using SNMP. Enter a password in both the Password field and the Confirm field. This password must be between 6 and 32 characters. The default password is public. SNMP Read/Write Community Password: The password for read and write access to the AP using SNMP. Enter a password in both the Password field and the Confirm field. This password must be between 6 and 32 characters. The default password is public. SNMPv3 Authentication Password: The password used when sending authenticated SNMPv3 messages. Enter a password in both the Password field and the Confirm field. This password must be between 6 and 32 characters, but a length of at least at least 8 characters is recommended. The default password is public. Secure Management (Services tab) must be enabled to configure SNMPv3. The default SNMPv3 username is administrator, with SHA authentication, and DES privacy protocol. SNMPv3 Privacy Password: The password used when sending encrypted SNMPv3 data. Enter a password in both the Password field and the Confirm field. This password must be between 6 and 32 characters, but a length of at least at least 8 characters is recommended. The default password is public. Secure Management (Services tab) must be enabled to configure SNMPv3. Telnet (CLI) Password: The password for the CLI interface (via serial or Telnet). Enter a password in both the Password field and the Confirm field. This password must be between 6 and 32 characters. The default password is public. HTTP (Web) Password: The password for the Web browser HTTP interface. Enter a password in both the Password field and the Confirm field. This password must be between 6 and 32 characters. The default password is public.

NOTE
For security purposes Proxim recommends changing ALL PASSWORDS from the default public immediately, to restrict access to your network devices to authorized personnel. If you lose or forget your password settings, you can always perform the Reset to Factory Default Procedure.

IP Access Table
The Management IP Access table limits in-band management access to the IP addresses or range of IP addresses specified in the table. This feature applies to all management options (SNMP, HTTP, and CLI) except for CLI management over the serial port. To configure this table, click Add and set the following parameters: IP Address: Enter the IP Address for the management station. IP Mask: Enter a mask that will act as a filter to limit access to a range of IP Addresses based on the IP Address you already entered. The IP mask 255.255.255.255 would authorize the single station defined by the IP Address to configure the Access Point. The AP would ignore commands from any other IP address. In contrast, the IP mask 255.255.255.0 would allow any device that shares the first three octets of the IP address to configure the AP. For example, if you enter an IP address of 10.20.30.1 with a 255.255.255.0 subnet mask, any IP address between 10.20.30.1 and 10.20.30.254 will have access to the APs management interfaces. Comment: Enter an optional comment, such as the station name.

To edit or delete an entry, click Edit. Edit the information, or select Enable, Disable, or Delete from the Status pull-down menu.

53

Performing Advanced Configuration Services

You can configure the following management services:

NOTE
You must reboot the Access Point if you change the HTTP Port or Telnet Port.

Secure Management
Secure Management allows the use of encrypted and authenticated communication protocols such as SNMPv3, and Secure Socket Link (SSL), to manage the Access Point. Secure Management Status: Enables the further configuration of HTTPS Access, and SNMPv3. After enabling Secure Management, you can choose to configure HTTPS (SSL) access on the Services tab, and configure SNMPv3 passwords on the Passwords tab.

SNMP Settings
SNMP Interface Bitmask: Configure the interface or interfaces (Ethernet, Wireless-Slot A, Wireless-Slot B, All Interfaces) from which you will manage the AP via SNMP. Select Disabled to prevent a user from accessing the AP via SNMP.

HTTP Access
HTTP Interface Bitmap: Configure the interface or interfaces (Ethernet, Wireless-Slot A, Wireless-Slot B, All Interfaces) from which you will manage the AP via the Web interface. For example, to allow Web configuration via the Ethernet network only, set HTTP Interface Bitmask to Ethernet. Select Disabled to prevent a user from accessing the AP from the Web interface. HTTP Port: Configure the HTTP port from which you will manage the AP via the Web interface. By default, the HTTP port is 80. You must reboot the Access Point if you change the HTTP Port. HTTP Setup Wizard: The Setup Wizard appears automatically the first time you access the HTTP interface. If you exited out of the Setup Wizard and want to relaunch it, enable this option, click OK, and then close your browser or reboot the AP. The Setup Wizard will appear the next time you access the HTTP interface.

HTTPS Access
HTTPS (Secure Web Status): The user can access the AP in a secure fashion using Secure Socket Layer (SSL) over port 443. The AP comes pre-installed with all required SSL files: default certificate and private key installed. Check this box to enable SSL on the AP. SSL Certificate Passphrase: After enabling SSL, the only configurable parameter is the SSL passphrase. The default SSL passphrase is proxim. The AP supports SSLv3 with a 128-bit encryption certificate maintained by the AP for secure communications between the AP and the HTTP client. All communications are encrypted using the server and the client-side certificate. If you decide to upload a new certificate and private key (using TFTP or HTTP File Transfer), you need to change the SSL Certificate Passphrase for the new SSL files.

NOTE
SSL requires Internet Explorer version 6, 128 bit encryption, Service Pack 1, and patch Q323308.

NOTE
You need to reboot the AP after enabling or disabling SSL for the changes to take effect.

Accessing the AP through the HTTPS interface

The user should use a SSL intelligent browser to access the AP through the HTTPS interface. After configuring SSL, access the AP using https:// followed by the APs management IP address.

54

Performing Advanced Configuration

Figure 4-10

Management Services Configuration Screen

55

Performing Advanced Configuration

Telnet Configuration Settings
Telnet Interface Bitmask: Select the interface (Ethernet, Wireless-Slot A, Wireless-Slot B, All Interfaces) from which you can manage the AP via telnet. This parameter can also be used to Disable telnet management. Telnet Port: The default port number for Telnet applications is 23. However, you can use this field if you want to change the Telnet port for security reasons (but your Telnet application also must support the new port number you select). You must reboot the Access Point if you change the Telnet Port. Login Idle Timeout (seconds): Enter the number of seconds the system will wait for a login attempt. The AP terminates the session when it times out. The range is 1 to 300 seconds; the default is 30 seconds. Session Idle Timeout (seconds): Enter the number of seconds the system will wait during a session while there is no activity. The AP will terminate the session on timeout. The range is 1 to 36000 seconds; the default is 900 seconds.

Secure Shell (SSH) Settings

The AP supports SSH version 2, for secure remote CLI (Telnet) sessions. SSH provides strong authentication and encryption of session data. The SSH server (AP) has host keys - a pair of assymetric keys - a private key that resides on the AP and a public key that is distributed to clients that need to connect to the AP. As the client has knowledge of the server host keys, the client can verify that it is communicating with the correct SSH server. The client authentication can be performed in two ways: Using asymmetric keys. This method requires all the client keys to be installed on the AP. Using a username/password pair to authenticate the user over a secure channel created using SSH.

SSH Session Setup

An SSH session is setup through the following process: The SSH server public key is transferred to the client using out-of-band or in-band mechanisms. The SSH client verifies the correctness of the server using the servers public key. The user/client authenticates to the server. An encrypted data session starts. The maximum number of SSH sessions is limited to two. If there is no activity for a specified amount of time (the Telnet Session Timeout parameter), the AP will timeout the connection.

SSH Clients
The following SSH clients have been verified to interoperate with the APs server. The following table lists the clients, version number, and the website of the client.
Clients OpenSSH Putty Zoc Axessh Version V3.4-2 Rel 0.53b 5.00 V2.5 Website http://www.openssh.com http://www.chiark.greenend.org.uk http://www.emtec.com http://www.labf.com

For key generation, OpenSSH client has been verified.

Configuring SSH
Perform the following procedure to enable or disable SSH and set the SSH host key: 1. Click Configure -> Management -> Services. 2. To enable SSH, select Enable from the Enable SSH (Secure Shell) drop down menu.

NOTE
When Secure Management is enabled on the AP, SSH will be enabled by default and cannot be disabled. 3. Select the SSH Host Key Status from the drop-down menu. Host keys must either be generated externally and uploaded to the AP (see Uploading Externally Generated Host Keys), generated manually, or auto-generated at the time of SSH initialization if SSH is enabled and no host keys are present. There is no key present in an AP that is in a factory default state.

56

Performing Advanced Configuration

To manually generate or delete host keys on the AP: Select Create to generate a new pair of host keys. Select Delete to remove the host keys from the AP. If no host keys are present, the AP will not allows connections using SSH. When host keys are created or deleted, the AP updates the fingerprint information displayed on the Management -> Services page.

WARNING
SSH Host key creation may take 3 to 4 minutes during which time the AP may not respond.

Uploading Externally Generated Host Keys

Perform the following procedure to upload externally generated host keys to the AP. You must upload both the SSH public key and SSH private key for SSH to work. 1. Verify that the host keys have been externally generated. The OpenSSH client has been verify to interoperate with APs SSH server. 2. Click Commands -> Update AP -> via HTTP (or via TFTP).

Figure 4-11

Uploading an Externally Generated SSH Public Key and SSH Private Key

3. Select SSH Public Key from the File Type drop-down menu. 4. Click Browse, select the SSH Public Key file on your local machine. 5. Click Open. 6. to initiate the file transfer, click the Update AP button. 7. Select SSH Private Key from the File Type drop-down menu. 8. Click Browse, select the SSH Private Key on your local machine. 9. Click Open. 10. To initiate the file transfer, click the Update AP button. The fingerprint of the new SSH public key will be displayed in the Management -> Services page.

57

Performing Advanced Configuration

Serial Configuration Settings
The serial port interface on the AP is enabled at all times. See Setting IP Address using Serial Port for information on how to access the CLI interface via the serial port. You can configure and view following parameters: Serial Baud Rate: Select the serial port speed (bits per second). Choose between 2400, 4800, 9600, 19200, 38400, or 57600; the default Baud Rate is 9600. Serial Flow Control: Select either None (default) or Xon/Xoff (software controlled) data flow control.

NOTE
To avoid potential problems when communicating with the AP through the serial port, Proxim recommends that you leave the Flow Control setting at None (the default value). Serial Data Bits: This is a read-only field and displays the number of data bits used in serial communication (8 data bits by default). Serial Parity: This is a read-only field and displays the number of parity bits used in serial communication (no parity bits by default). Serial Stop Bits: This is a read-only field that displays the number of stop bits used in serial communication (1 stop bit by default).

NOTE
The serial port bit configuration is commonly referred to as 8N1.

RADIUS Based Management Access

User management of APs can be centralized by using a RADIUS server to store user credentials. The AP cross-checks credentials using RADIUS protocol and the RADIUS server accepts or rejects the user. HTTP/HTTPS and Telnet/SSH users can be managed with RADIUS. Serial CLI and SNMP cannot be managed by RADIUS. Two types of users can be supported using centralized RADIUS management: Super User: The super user has access to all functionality of a management interface. A super user is configured in the RADIUS server by setting the filter ID attribute (returned in the RADIUS Accept packet) for the user to a value of super user (not case sensitive). A user is considered a super user if the value of the filter-id attribute returned in the RADIUS Accept packet for the user is super user (not case sensitive). Limited User: A limited user has access to only a limited set of functionality on a management interface. All users who are not super users are considered limited users. However, a limited user is configured in the RADIUS server by setting the filter-id attribute (returned in the RADIUS Accept packet) to limited user (not case sensitive). Limited users do not have access to the following configuration capabilities: Update/retrieve files to and from APs Reset the AP to factory defaults Reboot the AP Change management properties related to RADIUS, management modes, and management passwords.

When RADIUS Based Management is enabled, a local user can be configured to provide Telnet, SSH, and HTTP(S) access to the AP when RADIUS servers fail. The local user has super user capabilities. When secure management is enabled, the local user can only login using secure means (i.e., SSH or SSL). When the local user option is disabled the only access to the AP when RADIUS servers are down will be through serial CLI or SNMP. The Radius Based Management Access parameters allows you to enable HTTP or Telnet Radius Management Access, to configure a RADIUS Profile for management access control, and to enable or disable local user access, and configure the local user password. You can configure and view the following parameters: HTTP RADIUS Access Control Status: Enable RADIUS management of HTTP/HTTPS users. Telnet RADIUS Access Control Status: Enable RADIUS management of Telnet/SSH users. RADIUS Profile for Management Access Control: Specifies the RADIUS Profile to be used for RADIUS Based Management Access. Local User Status: Enables or disables the local user when RADIUS Based Management is enabled. The default local user ID is root. Local User Password and Confirm Password: The default local user password is public. Root cannot be configured as a valid user for Radius based management access when local user access is enabled.

58

Performing Advanced Configuration Automatic Configuration (AutoConfig)

The Automatic Configuration feature which allows an AP to be automatically configured by downloading a specific configuration file from a TFTP server during the boot up process. Automatic Configuration is disabled by default. The configuration process for Automatic Configuration varies depending on whether the AP is configured for dynamic or static IP. When an AP is configured for dynamic IP, the Configuration filename and the TFTP server IP address are contained in the DHCP response when the AP gets its IP address dynamically from the DHCP server. When configured for static IP, these parameters are instead configured in the AP interface. After setting up automatic configuration you must reboot the AP. When the AP reboots it receives the new configuration information and must reboot one additional time. If Syslog is configured, a Syslog message will appear indicating the success or failure of the Automatic Configuration.

Auto Configuration and the CLI Batch File

The Auto Configuration feature allows download of the TLV (tag, length, value) format configuration file or the CLI Batch file. The AP detects whether the file uploaded is TLV format or a CLI Batch file. If the AP detects a CLI Batch file (a file with extension .cli), the AP executes the file immediately. The AP will reboot after executing the CLI Batch file. Auto Configuration will not result in repeated reboots if the CLI Batch file contains rebootable parameters. For more information, refer to CLI Batch File.

Set up Automatic Configuration for Static IP

Perform the following procedure to enable and set up Automatic Configuration when you have a static IP address for the TFTP server. 1. Click Configure > Management > AutoConfig. The Automatic Configuration Screen appears. 2. Check Enable Auto Configuration. 3. Enter the Configuration Filename. 4. Enter the IP address of the TFTP server in the TFTP Server Address field.

NOTE
The default filename is config. The default TFTP IP address is 10.0.0.2 for AP-2000. 5. Click OK to save the changes. 6. Reboot the AP. When the AP reboots it receives the new configuration information and must reboot one additional time. If a Syslog server was configured, the following messages can be observed on the Syslog server: AutoConfig for Static IP TFTP server address and configuration filename AutoConfig Successful

59

Performing Advanced Configuration

Figure 4-12

Automatic Configuration Screen

Set up Automatic Configuration for Dynamic IP

Perform the following procedure to enable and set up Automatic Configuration when you have a dynamic IP address for the TFTP server via DHCP. The Configuration filename and the TFTP server IP address are contained in the DHCP response when the AP gets its IP address dynamically from the DHCP server. A Syslog server address is also contained in the DHCP response, allowing the AP to send Auto Configuration success and failure messages to a Syslog server.

NOTE
The configuration filename and TFTP server IP address are configured only when the AP is configured for Static IP. If the AP is configured for Dynamic IP these parameters are not used and obtained from DHCP. 1. Click Configure > Management > AutoConfig. The Automatic Configuration Screen appears. 2. Check Enable Auto Configuration. When the AP is Configured with Dynamic IP, the DHCP server should be configured with the TFTP Server IP address ("Boot Server Host Name", option 66) and Configuration file ("Bootfile name", option 67) as follows (note that this example uses a Windows 2000 server): 3. Select DHCP Server > DHCP Option > Scope. The DHCP Options: Scope Screen appears.

60

Performing Advanced Configuration

Figure 4-13 DHCP Options: Setting the Boot Server Host Name

4. Add the Boot Server Host Name and Boot Filename parameters to the Active Options list. 5. Set the value of the Boot Server Host Name Parameter to the host name or IP Address of the TFTP server. For example: 11.0.0.7.

Figure 4-14

DHCP Options: Setting the Boot Server Host Name

6. Set the value of the Bootfile Name parameter to the Configuration filename. For example: AP-Config 7. If using Syslog, set the Log server IP address (option 7, Log Servers). 8. Reboot the AP. When the AP reboots it receives the new configuration information and must reboot one additional time. If a Syslog server was configured, the following messages can be observed on the Syslog server: AutoConfig for Dynamic IP TFTP server address and configuration filename AutoConfig Successful

61

Performing Advanced Configuration Hardware Configuration Reset (CHRP)

Hardware Configuration Reset Status is a parameter that defines the hardware configuration reset behavior of the AP (i.e., what effect pressing the reload button has on an AP operating in normal operating mode). If a user loses or forgets the APs HTTP/Telnet/SNMP password, the reset button on the AP provides a way to reset the AP to default configuration values to gain access to the AP. However, in AP deployments where physical access to the AP is not protected, an unauthorized person could reset the AP to factory defaults and thus gain control of the AP. The user can disable the hardware configuration reset functionality to prevent unauthorized access. The hardware configuration reset feature operates as follows: When hardware configuration reset is enabled, the user can press the hardware reload button for 10 seconds when the AP is in normal operational mode in order to delete the AP configuration. When hardware configuration reset is disabled, pressing the reload button when the AP is in normal operational mode does not have any effect on the AP. The hardware configuration reset parameter does not have any effect on the functionality of the reload button to delete the AP image during AP boot loaded execution. The default hardware configuration reset status is enabled. When disabling hardware configuration reset, the user is recommended to configure a configuration reset password. A configuration reset option appears on the serial port during boot up, before the AP reads its configuration and initializes. Whenever the AP is reset to factory default configuration, hardware configuration reset status is enabled and the configuration reset password is set to the default, public. If secure mode is enabled in the AP, only secure (SSL, SNMPv3, SSH) users can modify the values of the Hardware Configuration Reset Status and the configuration reset password.

Configuration Reset via Serial Port During Bootup

If hardware configuration reset is disabled, the user gets prompted by a configuration reset option to reset the AP to factory defaults during boot up from the serial interface. By pressing a key sequence (ctrl-R), the user gets prompted to enter a configuration reset password before the configuration is reset.

NOTE
It is important to safely store the configuration reset password. If a user forgets the configuration reset password, the user will be unable to reset the AP to factory default configuration if the AP becomes inaccessible and the hardware configuration reset functionality is disabled.

62

Performing Advanced Configuration

Configuring Hardware Configuration Reset
Perform the following procedure to configure Hardware Configuration Reset and to set the Configuration Reset Password. 1. Click Configure -> Management -> CHRD. 2. Check (enable) or uncheck (disable) the Enable Hardware Configuration Reset checkbox. 3. Change the default Configuration Reset Password in the Configuration Reset Password and Confirm fields.

NOTE
It is important to safely store the configuration reset password. If a user forgets the configuration reset password, the user will be unable to reset the AP to factory default configuration if the AP becomes inaccessible and the hardware configuration reset functionality is disabled.

Figure 4-15

Hardware Configuration Reset

Procedure to Reset Configuration via the Serial Interface

1. During boot up, observe the message output on the serial interface. The AP prompts the user with the message: Press ctrl-R in 3 seconds to choose configuration reset option. 2. Enter ctrl-R within 3 seconds after being prompted. The AP prompts the user with Press ctrl-Z to continue with normal boot up or enter password to reset configuration. If the user enters ctrl-Z, the AP continues to boot with the stored configuration. 3. Enter the configuration reset password. The default configuration reset password is public. When the correct configuration reset password is entered, the AP gets reset to factory defaults and displays the message AP has been reset to Factory Default Settings. The AP continues to boot up. If an incorrect configuration reset password is entered, the AP shows an error message and reprompts the user. If the incorrect password is entered three times in a row, the AP proceeds to boot up.

63

Performing Advanced Configuration

Filtering
The Access Points Packet Filtering features help control the amount of traffic exchanged between the wired and wireless networks. There are four sub-tabs under the Filtering tab: Ethernet Protocol Static MAC Advanced TCP/UDP Port

Ethernet Protocol
The Ethernet Protocol Filter blocks or forwards packets based on the Ethernet protocols they support. Follow these steps to configure the Ethernet Protocol Filter: 1. Select the interface or interfaces that will implement the filter from the Ethernet Protocol Filtering drop-down menu. Ethernet: Packets are examined at the Ethernet interface Wireless - Slot A: Packets are examined at the Wireless A interface Wireless - Slot B: Packets are examined at the Wireless B interface All Interfaces: Packets are examined at both interfaces Disabled: The filter is not used 2. Select the Filter Operation Type. If set to Passthru, only the enabled Ethernet Protocols listed in the Filter Table will pass through the bridge. If set to Block, the bridge will block enabled Ethernet Protocols listed in the Filter Table. 3. Configure the Ethernet Protocol Filter Table. This table is pre-populated with existing Ethernet Protocol Filters, however, you may enter additional filters by specifying the appropriate parameters. To add an entry, click Add, and then specify the Protocol Number and a Protocol Name. Protocol Number: Enter the protocol number. See http://www.iana.org/assignments/ethernet-numbers for a list of protocol numbers. Protocol Name: Enter related information, typically the protocol name. To edit or delete an entry, click Edit and change the information, or select Enable, Disable, or Delete from the Status drop-down menu. An entrys status must be enabled in order for the protocol to be subject to the filter. 4. Reboot the AP for any changes to the Ethernet Protocol Filter Table to take effect.

Static MAC
The Static MAC Address filter optimizes the performance of a wireless (and wired) network. When this feature is properly configured, the AP can block traffic between wired devices and wireless devices based on MAC address. For example, you can set up a Static MAC filter to prevent wireless clients from communicating with a specific server on the Ethernet network. You can also use this filter to block unnecessary multicast packets from being forwarded to the wireless network.

NOTE
The Static MAC Filter is an advanced feature. You may find it easier to control wireless traffic via other filtering options, such as Ethernet Protocol Filtering. Each static MAC entry contains the following fields: Wired MAC Address Wired Mask Wireless MAC Address Wireless Mask Comment: This field is optional. Status

64

Performing Advanced Configuration

Each MAC Address or Mask is comprised of 12 hexadecimal digits (0-9, A-F) that correspond to a 48-bit identifier. (Each hexadecimal digit represents 4 bits (0 or 1).) Taken together, a MAC Address/Mask pair specifies an address or a range of MAC addresses that the AP will look for when examining packets. The AP uses Boolean logic to perform an AND operation between the MAC Address and the Mask at the bit level. However, for most users, you do not need to think in terms of bits. It should be sufficient to create a filter using only the hexadecimal digits 0 and F in the Mask (where 0 is any value and F is the value specified in the MAC address). A Mask of 00:00:00:00:00:00 corresponds to all MAC addresses, and a Mask of FF:FF:FF:FF:FF:FF applies only to the specified MAC Address. For example, if the MAC Address is 00:20:A6:12:54:C3 and the Mask is FF:FF:FF:00:00:00, the AP will examine the source and destination addresses of each packet looking for any MAC address starting with 00:20:A6. If the Mask is FF:FF:FF:FF:FF:FF, the AP will only look for the specific MAC address (in this case, 00:20:A6:12:54:C3). When creating a filter, you can configure the Wired parameters only, the Wireless parameters only, or both sets of parameters. Which parameters to configure depends upon the traffic that you want block: To prevent all traffic from a specific wired MAC address from being forwarded to the wireless network, configure only the Wired MAC Address and Wired Mask (leave the Wireless MAC Address and Wireless Mask set to all zeros). To prevent all traffic from a specific wireless MAC address from being forwarded to the wired network, configure only the Wireless MAC address and Wireless Mask (leave the Wired MAC Address and Wired Mask set to all zeros). To block traffic between a specific wired MAC address and a specific wireless MAC address, configure all four parameters.

To create an entry, click Add and enter the appropriate MAC addresses and Masks to setup a filter. The entry is enabled automatically when saved. To edit an entry, click Edit. To disable or remove an entry, click Edit and change the Status field from Enable to Disable or Delete.

Figure 4-16

Static MAC Configuration Screen

65

Performing Advanced Configuration

Static MAC Filter Examples
Consider a network that contains a wired server and three wireless clients. The MAC address for each unit is as follows: Wired Server: 00:40:F4:1C:DB:6A Wireless Client 1: 00:02:2D:51:94:E4 Wireless Client 2: 00:02:2D:51:32:12 Wireless Client 3: 00:20:A6:12:4E:38

Prevent Two Specific Devices from Communicating

Configure the following settings to prevent the Wired Server and Wireless Client 1 from communicating: Wired MAC Address: 00:40:F4:1C:DB:6A Wired Mask: FF:FF:FF:FF:FF:FF Wireless MAC Address: 00:02:2D:51:94:E4 Wireless Mask: FF:FF:FF:FF:FF:FF

Result: Traffic between the Wired Server and Wireless Client 1 is blocked. Wireless Clients 2 and 3 can still communicate with the Wired Server.

Prevent Multiple Wireless Devices From Communicating With a Single Wired Device
Configure the following settings to prevent Wireless Clients 1 and 2 from communicating with the Wired Server. Wired MAC Address: 00:40:F4:1C:DB:6A Wired Mask: FF:FF:FF:FF:FF:FF Wireless MAC Address: 00:02:2D:51:94:E4 Wireless Mask: FF:FF:FF:00:00:00

Result: When a logical AND is performed on the Wireless MAC Address and Wireless Mask, the result corresponds to any MAC address beginning with the 00:20:2D prefix. Since Wireless Client 1 and Wireless Client 2 share the same prefix (00:02:2D), traffic between the Wired Server and Wireless Clients 1 and 2 is blocked. Wireless Client 3 can still communicate with the Wired Server since it has a different prefix (00:20:A6).

Prevent All Wireless Devices From Communicating With a Single Wired Device
Configure the following settings to prevent all three Wireless Clients from communicating with Wired Server 1. Wired MAC Address: 00:40:F4:1C:DB:6A Wired Mask: FF:FF:FF:FF:FF:FF Wireless MAC Address: 00:00:00:00:00:00 Wireless Mask: 00:00:00:00:00:00

Result: The Access Point blocks all traffic between Wired Server 1 and all wireless clients.

Prevent A Wireless Device From Communicating With the Wired Network

Configure the following settings to prevent Wireless Client 3 from communicating with any device on the Ethernet. Wired MAC Address: 00:00:00:00:00:00 Wired Mask: 00:00:00:00:00:00 Wireless MAC Address: 00:20:A6:12:4E:38 Wireless Mask: FF:FF:FF:FF:FF:FF

Result: The Access Point blocks all traffic between Wireless Client 3 and the Ethernet network.

Prevent Messages Destined for a Specific Multicast Group from Being Forwarded to the Wireless LAN
If there are devices on your Ethernet network that use multicast packets to communicate and these packets are not required by your wireless clients, you can set up a Static MAC filter to preserve wireless bandwidth. For example, if routers on your network use a specific multicast address (such as 01:00:5E:00:32:4B) to exchange information, you can set up a filter to prevent these multicast packets from being forwarded to the wireless network: Wired MAC Address: 01:00:5E:00:32:4B

66

Performing Advanced Configuration

Wired Mask: FF:FF:FF:FF:FF:FF Wireless MAC Address: 00:00:00:00:00:00 Wireless Mask: 00:00:00:00:00:00

Result: The Access Point does not forward any packets that have a destination address of 01:00:5E:00:32:4B to the wireless network.

Advanced
You can configure the following advanced filtering options: Enable Proxy ARP: Place a check mark in the box provided to allow the Access Point to respond to Address Resolution Protocol (ARP) requests for wireless clients. When enabled, the AP answers ARP requests for wireless stations without actually forwarding them to the wireless network. If disabled, the Access Point will bridge ARP requests for wireless clients to the wireless LAN. Enable IP/ARP Filtering: Place a check mark in the box provided to allow IP/ARP filtering based on the IP/ARP Filtering Address and IP Mask. Leave the box unchecked to prevent filtering. If enabled, you should also configure the IP/ARP Filtering Address and IP/ARP IP Mask. IP/ARP Filtering Address: Enter the Network filtering IP Address. IP/ARP IP Mask: Enter the Network Mask IP Address.

The following protocols are listed in the Advanced Filter Table: Deny IPX RIP Deny IPX SAP Deny IPX LSP Deny IP Broadcasts Deny IP Multicasts

The AP can filter these protocols in the wireless-to-Ethernet direction, the Ethernet-to-wireless direction, or in both directions. Click Edit and use the Status field to Enable or Disable the filter.

TCP/UDP Port
Port-based filtering enables you to control wireless user access to network services by selectively blocking TCP/UDP protocols through the AP. A user specifies a Protocol Name, Port Number, Port Type (TCP, UDP, or TCP/UDP), and filtering interfaces ( Ethernet, Wireless A only, Wireless A and Ethernet, Wireless B only, Wireless B and Ethernet, All Interfaces) in order to block access to services, such as Telnet and FTP, and traffic, such as NETBIOS and HTTP. For example, an AP with the following configuration would discard frames received on its Ethernet interface with a UDP destination port number of 137, effectively blocking NETBIOS Name Service packets.
Protocol Type (TCP/UDP) UDP Destination Port Number 137 Protocol Name NETBIOS Name Service Interface Ethernet Status (Enable/Disable) Enable

Adding TCP/UDP Port Filters

1. 2. 3. 4. Place a check mark in the box labeled Enable TCP/UDP Port Filtering. Click Add under the TCP/UDP Port Filter Table heading. In the TCP/UDP Port Filter Table, enter the Protocol Names to filter. Set the destination Port Number (a value between 1 and 65535) to filter. See the IANA Web site at http://www.iana.org/assignments/port-numbers for a list of assigned port numbers and their descriptions. 5. Set the Port Type for the protocol: TCP, UDP, or both (TCP/UDP). 6. Set the Interface to: Ethernet Wireless Slot A

67

Performing Advanced Configuration

Ethernet and Wireless Slot A Wireless Slot B Ethernet and Wireless Slot B Wireless Slot A and B All Interfaces 7. Click OK.

Editing TCP/UDP Port Filters

1. 2. 3. 4. Click Edit under the TCP/UDP Port Filter Table heading. Make any changes to the Protocol Name or Port Number for a specific entry, if necessary. Modify the Port Type, Interface, and Status using the drop down menus, as appropriate. Select OK.

68

Performing Advanced Configuration

Alarms
This tab has three sub-tabs. Groups Alarm Host Table Syslog Rogue Access Point Detection (RAD)

Groups
The AP can be configured to generate and send alarms/notifications/traps as version 1 or a version 2c. Use the drop-down menu to select SNMP alarm type. There are seven alarm groups that can be enabled or disabled via the Web interface. Place a check mark in the box provided to enable a specific group. Remove the check mark from the box to disable the alarms. Alarm Severity Levels vary.

Figure 4-17

Syslog Configuration Screen

Configuration Trap Group

Trap Name DNS IP Address not Configured RADIUS Authentication not Configured RADIUS Accounting not Configured Duplicate IP Address Encountered VLAN ID Invalid Configuration Auto Configuration Failure CLI Configuration Execution Failure CLI Configuration Execution Start CLI Configuration Execution End Description oriTrapDNSIPNotConfigured oriTrapRADIUSAuthenticationNotConfigured oriTrapRADIUSAccountingNotConfigured oriTrapDuplicateIPAddressEncountered oriTrapVLANIDInvalidConfiguration oriTrapAutoConfigFailure oriTrapBatchExecFailure oriTrapBatchFileExecStart oriTrapBatchFileExecEnd

69

Performing Advanced Configuration

Security Trap Group
Trap Name Authentication Failure Unauthorized Manager Detected RAD Scan Complete RAD Scan Results Description oriTrapAuthenticationFailure oriTrapUnauthorizedManagerDetected oriTrapRADScanComplete oriTrapRADScanResults

Wireless Interface/Card Trap Group

Trap Name Wireless Card Not Present Wireless Card Failure Wireless Card Removal Incompatible Firmware Incompatible Vendor Firmware Download Failure (classic card only) Firmware Failure Radar Interference Detected Description oriTrapWLCNotPresent oriTrapWLCFailure oriTrapWLCRemoval oriTrapWLCIncompatibleFirmware oriTrapWLCIncompatibleVendor oriTrapWLCFirmwareDownloadFailure oriTrapWLCFirmwareFailure oriTrapWLCRadarInterferenceDetected

Operational Trap Group

Trap Name Unrecoverable Software Error Detected RADIUS Server Not Responding Module Not Initialized Device Rebooting Task Suspended BootP Failed DHCP Client Failed DNS Client Lookup Failure SSL Initialization Failure SSH Initialization Status Assigned User VLAN ID DHCP Lease Renewal Description oriTrapUnrecoverableSoftwareErrorDetected oriTrapRADIUSServerNotResponding oriTrapModuleNotInitialized oriTrapDeviceRebooting oriTrapTaskSuspended oriTrapBootPFailed oriTrapDHCPFailed oriTrapDNSClientLookupFailure oriTrapSSLInitializationFailure oriTrapSSHInitializationStatus oriTrapVLANIDUserAssignment oriTrapDHCPLeaseRenewal

Flash Memory Trap Group

Trap Name Flash Memory Empty Description oriTrapFlashMemoryEmpty

70

Performing Advanced Configuration

Flash Memory Corrupted Restoring Last Known Good Configuration File oriTrapFlashMemoryCorrupted oriTrapFlashMemoryRestoringLastKnownGoodConfiguration

TFTP Trap Group

Trap Name TFTP Operation Failure TFTP Operation Initiated TFTP Operation Completed Description oriTrapTFTPFailedOperation oriTrapTFTPOperationInitiated oriTrapTFTPOperationCompleted

Image Trap Group

Trap Name Zero Size Image Invalid Image Image Too Large Incompatible Image Invalid Image Digital Signature oriTrapZeroSizeImage oriTrapInvalidImage oriTrapImageTooLarge oriTrapIncompatibleImage oriTrapInvalidImageDigitalSignature Description

In addition, the AP supports these standard traps, which are always enabled: RFC 1215-Trap
Trap Name coldStart Description The AP has been turned on or rebooted. Trap Severity Level: Informational The AP's Ethernet interface link is up (working). Trap Severity Level: Informational The AP's Ethernet interface link is down (not working). Trap Severity Level: Informational

linkUp

linkDown

Bridge MIB (RFC 1493) Alarms

Trap Name newRoot Description This trap indicates that the AP has become the new root in the Spanning Tree network. Trap Severity Level: Informational This trap is sent by the AP when any of its configured ports transitions from the Learning state to the Forwarding state, or from the Forwarding state to the Blocking state. This trap is not sent if a newRoot trap is sent for the same transition. Trap Severity Level: Informational

topologyChange

All these alarm groups correspond to System Alarms that are displayed in the System Status screen, including the traps that are sent by the AP to the SNMP managers specified in the Alarm Host Table.

71

Performing Advanced Configuration

Severity Levels
There are three severity levels for system alarms: Critical Major Informational

Critical alarms will often result in severe disruption in network activity or an automatic reboot of the AP Major alarms are usually activated due to a breach in the security of the system. Clients cannot be authenticated or an attempt at unauthorized access into the AP has been detected. Informational alarms are there to provide the network administrator with some general information about the activities the AP is performing.

Alarm Host Table

To add an entry and enable the AP to send SNMP trap messages to a Trap Host, click Add, and then specify the IP Address and Password for the Trap Host.

NOTE
Up to 10 entries are possible in the Alarm Host table. IP Address: Enter the Trap Host IP Address. Password: Enter the password in the Password field and the Confirm field. Comment: Enter an optional comment, such as the alarm (trap) host station name.

To edit or delete an entry, click Edit. Edit the information, or select Enable, Disable, or Delete from the Status drop-down menu.

Syslog
The Syslog messaging system enables the AP to transmit event messages to a central server for monitoring and troubleshooting. The AP can send messages to multiple Syslog servers. The access point logs Session Start (Log-in) and Session Stop (Log-out) events for each wireless client as an alternative to RADIUS accounting. See RFC 3164 at http://www.rfc-editor.org for more information on the Syslog standard.

Setting Syslog Event Notifications

Syslog Events are logged according to the level of detail specified by the administrator. Logging only urgent system messages will create a far smaller, more easily read log then a log of every event the system encounters. Determine which events to log by selecting a priority defined by the following scale:
Event LOG_EMERG LOG_ALERT LOG_CRIT LOG_ERR LOG_WARNING LOG_NOTICE LOG_INFO LOG_DEBUG Priority 0 1 2 3 4 5 6 7 Description system is unusable action must be taken immediately critical conditions error conditions warning conditions normal but significant condition informational debug-level messages

Configuring Syslog Event Notifications

You can configure the following Syslog settings from the HTTP interface: Enable Syslog: Place a check mark in the box provided to enable system logging. Syslog Port Number: This field is read-only and displays the port number (514) assigned for system logging. Syslog Lowest Priority Logged: The AP will send event messages to the Syslog server that correspond to the selected priority and above. For example, if set to 6, the AP will transmit event messages labeled priority 0 to 6 to the Syslog server(s). This parameter supports a range between 1 and 7; 6 is the default.

72

Performing Advanced Configuration

Syslog Heartbeat Status: Enables or disables the sending of heartbeat messages from the AP to the configured Syslog servers. Syslog Heartbeat Interval: Specifies the interval (in seconds) at which Syslog Heartbeat messages are sent to the configured Syslog servers. Syslog Host Table: This table specifies the IP addresses of a network servers that the AP will send Syslog messages to. Click Add to create a new entry. Click Edit to change an existing entry. Each entry contains the following field: IP Address: Enter the IP Address for the management host. Comment: Enter an optional comment such as the host name. Status: The entry is enabled automatically when saved (so the Status field is only visible when editing an entry). Disable or delete entries by changing this fields value.

Syslog Messages
The following messages are supported in the AP:
Message Auto Configuration via DHCP Auto Configuration for static IP TFTP server IP/Config filename missing in DHCP response AutoConfig TFTP server IP address used is <IP address> AutoConfig filename used is <filename> AutoConfig TFTP download failed Image Error check, invalid image AP Heartbeat status Client Authentication State Accounting RADIUS Responses Severity Informational Informational Minor Informational Informational Minor Minor Minor Informational Informational Informational

73

Performing Advanced Configuration Rogue Access Point Detection (RAD)

The Rogue AP Detection (RAD) feature provides an additional security level for wireless LAN deployments. Rogue AP detection provides a mechanism for detecting Rogue Access Points by utilizing the coverage of the trusted Access Point deployment. The Rogue AP Scan employs background scanning using low-level 802.11 scanning functions for effective wireless detection of Access Points in its coverage area with minimal impact on the normal operation of the Access Point. This RAD feature can be enabled on an Access Point via its HTTP, CLI, or SNMP Interfaces. The scan repetition duration is configurable. If the Access Point uses directional antennas to provide directional coverage, then the interface bitmask can be configured to maximize the scanning coverage area. The Access Point will periodically scan the wireless network and report all the available Access Points within its coverage area using SNMP traps. For additional reliability the results are stored in the Access Point in a table, which can be queried via SNMP. The BSSID and Channel number of the detected Access Points are provided in the scan results. The RAD scan is done on a channel list initialized based on the regulatory domain of the device. The RAD Scan then performs background scanning on all the channels in this channel list using 802.11 MAC scanning functions. It will either actively scan the network by sending probe requests or passively scan by only listening for beacons. The access point information is then gathered from the probe responses and beacons. To minimize traffic disruption and maximize the scanning efficiency, the RAD feature employs an enhanced background-scanning algorithm and uses the CTS to Self mechanism to keep the clients silent. The scanning algorithm allows traffic to be serviced between each channel scan. Before start of every scan (except scan on the working channel) the CTS to self-mechanism is used to set the NAV values of clients to keep them silent during the scanning period. In addition, the scan repetition duration can also be configured to reduce the frequency of RAD scan cycles to maximize Access Point performance.

RAD Configuration Requirements

The RAD feature can be configured/monitored via the HTTP, CLI, or SNMP management interfaces. The following management options are provided: The RAD feature can be enabled or disabled. The repetition interval of RAD can be configured. The interface on which RAD can operate can be configured. SNMP Traps are sent after completion of a RAD scan cycle and also whenever a new Access Point is detected.

Trusted AP

Rogue AP

Management Station

Figure 4-18

Example Rogue AP Detection Deployment

Additionally, the RAD scan results are maintained in a table that can be queried via SNMP. The system administrator has to enable RAD on the Access Points in the wireless network and also configure the Trap Host on all these Access

74

Performing Advanced Configuration

Points to the IP address of the management station. The Access Points on detecting a new Access Point sends a RAD Scan Result Trap to the management station. An example network deployment is shown. The Trusted AP has Rogue Access Detection enabled and the trap host is configured to be the management station. The Trusted AP on detecting the Rogue AP will send a trap to the management station with the Channel and BSSID of the Rogue Access Point.

Configuring RAD
Perform this procedure to enable and configure RAD. The RAD screen also displays the time of the last scan and the number of new access points detected in the last scan. 1. Enable the Security Alarm Group. Select the Security Alarm Group link from the RAD screen. Configure a Trap Host to receive the list of access points detected during the scan. 2. Click Configure > Alarms > RAD. 3. Enable RAD by checking Enable Rogue AP Detection. 4. Enter the Scan Interval. The Scan Interval specifies the time period in minutes between scans and can be set to any value between 15 and 1440 minutes. 5. Select the Scan Interface as Wireless - Slot A, Wireless - Slot B, or Both Wireless - Slots A & B. 6. Click OK. The results of the RAD scan be viewed in the Status page in the HTTP interface.

Figure 4-19

Rogue Access Point Detection Screen

75

Performing Advanced Configuration

Bridge
The AP is a bridge between your wired and wireless networking devices. As a bridge, the functions performed by the AP include: MAC address learning Forward and filtering decision making Spanning Tree protocol used for loop avoidance

Once the AP is connected to your network, it learns which devices are connected to it and records their MAC addresses in the Learn Table. The table can hold up to 10,000 entries. To view the Learn Table, click on the Monitor tab and select the Learn Table tab. The Bridge tab has four sub-tabs. Spanning Tree Storm Threshold Intra BSS Packet Forwarding (Pkt Fwd)

Spanning Tree
A Spanning Tree is used to avoid redundant communication loops in networks with multiple bridging devices. Bridges do not have any inherent mechanism to avoid loops, because having redundant systems is a necessity in certain networks. However, redundant systems can cause Broadcast Storms, multiple frame copies, and MAC address table instability problems. Complex network structures can create multiple loops within a network. The Spanning Tree configuration blocks certain ports on AP devices to control the path of communication within the network, avoiding loops and following a spanning tree structure. For more information on Spanning Tree protocol, see Section 8.0 of the IEEE 802.1d standard. The Spanning Tree configuration options are advanced settings. Proxim recommends that you leave these parameters at their default values unless you are familiar with the Spanning Tree protocol.

Storm Threshold
Storm Threshold is an advanced Bridge setup option that you can use to protect the network against data overload by: Specifying a maximum number of frames per second as received from a single network device (identified by its MAC address). Specifying an absolute maximum number of messages per port.

The Storm Threshold parameters allow you to specify a set of thresholds for each port of the AP, identifying separate values for the number of broadcast messages/second and Multicast messages/second. When the number of frames for a port or identified station exceeds the maximum value per second, the AP will ignore all subsequent messages issued by the particular network device, or ignore all messages of that type. Address Threshold: Enter the maximum allowed number of packets per second. Ethernet Threshold: Enter the maximum allowed number of packets per second. Wireless-Slot A and Wireless-Slot B Threshold: Enter the maximum allowed number of packets per second.

Intra BSS
The wireless clients (or subscribers) that associate with a certain AP form the Basic Service Set (BSS) of a network infrastructure. By default, wireless subscribers in the same BSS can communicate with each other. However, some administrators (such as wireless public spaces) may wish to block traffic between wireless subscribers that are associated with the same AP to prevent unauthorized communication and to conserve bandwidth. This feature enables you to prevent wireless subscribers within a BSS from exchanging traffic. Although this feature is generally enabled in public access environments, Enterprise LAN administrators use it to conserve wireless bandwidth by limiting communication between wireless clients. For example, this feature prevents peer-to-peer file sharing or gaming over the wireless network.

76

Performing Advanced Configuration

To block Intra BSS traffic, set Intra BSS Traffic Operation to Block. To allow Intra BSS traffic, set Intra BSS Traffic Operation to Passthru.

Packet Forwarding (Pkt Fwd)

The Packet Forwarding feature enables you to redirect traffic generated by wireless clients that are all associated to the same AP to a single MAC address. This filters wireless traffic without burdening the AP and provides additional security by limiting potential destinations or by routing the traffic directly to a firewall. You can redirect to a specific port (Ethernet or WDS) or allow the bridges learning process (and the forwarding table entry for the selected MAC address) to determine the optimal port.

NOTE
The gateway to which traffic will be redirected should be node on the Ethernet network. It should not be a wireless client. To configure interfaces for packet forwarding, specifying interface port(s) to which packets are redirected and a destination MAC address, as follows: 1. Within the Packet Forwarding Configuration screen, check the box labeled Enable Packet Forwarding. 2. Specify a destination Packet Forwarding MAC Address. The AP will redirect all unicast, multicast, and broadcast packets received from wireless clients to the address you specify. 3. Select a Packet Forwarding Interface Port from the drop-down menu. You can redirect traffic to: Any Interface (traffic is redirected to a port based on the bridge learning process) Ethernet A WDS connection (see Wireless Distribution System (WDS) for details) 4. Click OK to save your changes.

QoS (Quality of Service)

This feature is not supported in the AP. Clicking on this tab displays the following message: The Quality of Service (QoS) feature is not implemented on the AP-600 and AP-2000.

77

Performing Advanced Configuration

RADIUS Profiles
Configuring RADIUS Profiles on the AP define a profile for RADIUS Servers used by the system or by a VLAN. The network administrator can define RADIUS Servers per Authentication Mode and per VLAN. The AP communicates with the RADIUS server defined in a profile to provide the following features: MAC Access Control Via RADIUS Authentication 802.1x Authentication using RADIUS RADIUS Accounting

Also, RADIUS Based Management Access allows centralized user management. The network administrator can configure default RADIUS authentication servers to be used on a system-wide basis, or in networks with VLANs enabled the administrator can also configure separate authentication servers to be used for MAC authentication, EAP authentication, or Accounting in each VLAN. You can configure the AP to communicate with up to six different RADIUS servers per VLAN/SSID: Primary Authentication Server (MAC-based authentication) Back-up Authentication Server (MAC-based authentication) Primary Authentication Server (EAP/802.1x authentication) Back-up Authentication Server (EAP/802.1x authentication) Primary Accounting Server Back-up Accounting Server

The back-up servers are optional, but when configured, the AP will communicate with the back-up server if the primary server is off-line. After the AP has switched to the backup server, it will periodically check the status of the primary RADIUS server every five (5) minutes. Once the primary RADIUS server is again online, the AP automatically reverts from the backup RADIUS server back to the primary RADIUS server. All subsequent requests are then sent to the primary RADIUS server. You can view monitoring statistics for each of the configured RADIUS servers.

RADIUS Servers per Authentication Mode and per VLAN

The user can configure separate RADIUS authentication servers for each authentication mode and for each SSID (VLAN). For example: the user can configure separate RADIUS servers for RADIUS MAC authentication and 802.1x authentication the user can configure separate RADIUS servers for each VLAN: the Sales VLAN could support only WEP clients, whereas the Marketing VLAN could support 802.1x and WEP clients.

AP

Figure 4-20

RADIUS Servers per VLAN

This figure shows a network with separate authentication servers for each authentication type and for each VLAN. The clients in VLAN 1 are authenticated using the authentication servers configured for VLAN 1. The type of authentication

78

Performing Advanced Configuration

server used depends on whether the authentication is done for an 802.1x client or non-802.1x client. The clients in VLAN 2 are authenticated using a different set of authentication servers configured for authenticating users in VLAN 2. Authentication servers for each VLAN are configured as part of the configuration options for that VLAN. You can also configure authentication servers on a system-wide basis; these are called the default authentication servers. For each VLAN, the user could opt to use the default authentication servers, or to configure separate authentication servers to be used for a particular authentication type in that VLAN.

RADIUS-based VLAN Assignment

Radius-based VLAN assignment The AP currently supports two methods of assigning a wireless client a VLAN ID. The wireless client can either be assigned the static VLAN ID configured for the SSID the wireless client is associated to, or the wireless client can be assigned a VLAN ID which is returned by the RADIUS server during authentication. A VLAN ID can only be assigned to a wireless client by a RADIUS server if they are associated to an SSID that is configured to a RADIUS-based authentication security mode/protocol (802.1X, WPA, 802.11i/WPA2, and RADIUS based MAC Address Authentication). If the wireless client is associated to an SSID that does not provide RADIUS-based authentication (such as None, WEP, WPA-PSK, and 802.11i/WPA2-PSK), then the wireless client will be assigned the static VLAN ID configured for respective SSID. See SSID/VLAN/Security for more information.

RADIUS Servers Enforcing VLAN Access Control

A RADIUS server can be used to enforce VLAN access control in two ways: Authorize the SSID the client uses to connect to the AP. The SSID determines the VLAN that the client gets assigned to.

Assigning the user to a VLAN by specifying the VLAN membership information of the user.

Configuring RADIUS Profiles

A RADIUS server Profile consists of a Primary and a Secondary RADIUS server that get assigned to act as either MAC Authentication servers, 802.1x/EAP Authentication servers, or Accounting Servers in the VLAN Configuration. Refer to SSID/VLAN/Security. The RADIUS Profiles tab allows you to add new RADIUS profiles or modify or delete existing profiles.

Figure 4-21

RADIUS Server Profiles

79

Performing Advanced Configuration

Adding or Modifying a RADIUS Server Profile
Perform the following procedure to add a RADIUS server profile and to configure its parameters. 1. Click Add to create a new profile. To Modify an existing profile, select the profile and click Edit. To delete an existing profile, select the profile and click Delete. You cannot delete a RADIUS server profile if you are using it in an SSID. Also, the four default RADIUS server profiles cannot be deleted.

Figure 4-22

Add RADIUS Server Profile

Configure the following parameters for the RADIUS Server profile:

NOTE
This page configures only the Primary RADIUS Server associated with the profile. After configuring these parameters, save them by clicking OK. Then, to configure the Secondary RADIUS Server, edit the profile from the main page. Server Profile Name: the profile name. This is the name used to associated a VLAN to the profile. Refer to SSID/VLAN/Security. MAC Address Format Type: This parameter should correspond to the format in which the clients 12-digit MAC addresses are listed within the RADIUS server. Available options are: Dash delimited: dash between each pair of digits: xx-yy-zz-aa-bb-cc Colon delimited: colon between each pair of digits: xx:yy:zz:aa:bb:cc Single dash delimited: dash between the sixth and seventh digits: xxyyzz-aabbcc No delimiters: No characters or spaces between pairs of hexidecimal digits: xxyyzzaabbcc Accounting Inactivity Timer: Enter the accounting inactivity timer. This parameter supports a value from 1-60 minutes. The default is 5 minutes. Authorization Lifetime: Enter the time, in seconds, each client session may be active before being automatically re-authenticated. This parameter supports a value between 900 and 43200 seconds. The default is 900 sec. Server Addressing Format: select IP Address or Name. If you want to identify RADIUS servers by name, you must configure the AP as a DNS Client. See DNS Client for details.

80

Performing Advanced Configuration

Server Name/IP Address: Enter the servers name or IP address. Destination Port: Enter the port number which the AP and the server will use to communicate. By default, RADIUS servers communicate on port 1812. Server VLAN ID: Indicates the VLAN that uses this RADIUS server profile. If VLAN is disabled, the text VLAN is disabled will appear. Shared Secret and Confirm Shared Secret: Enter the password shared by the RADIUS server and the AP. The same password must also be configured on the RADIUS server. Response Time (seconds): Enter the maximum time, in seconds, that the AP should wait for the RADIUS server to respond to a request. The range is 1-10 seconds; the default is 3 seconds. Maximum Retransmissions (0-4): Enter the maximum number of times an authentication request may be transmitted. The range is 0 to 4, the default is 3. Server Status: Select Enable from the drop-down box to enable the RADIUS Server Profile. 2. Click OK. 3. Select the Profile and click Edit to configure the Secondary RADIUS Server, if required. 4. Reboot the AP.

MAC Access Control Via RADIUS Authentication

If you want to control wireless access to the network and if your network includes a RADIUS Server, you can store the list of MAC addresses on the RADIUS server rather than configure each AP individually. You can define a RADIUS Profile that specifies the IP Address of the server that contains a central list of MAC Address values identifying the authorized stations that may access the wireless network. You must specify information for at least the primary RADIUS server. The back-up RADIUS server is optional.

NOTE
Each VLAN can be configured to use a separate RADIUS server (and backup server) for MAC authentication.

NOTE
Contact your RADIUS server manufacturer if you have problems configuring the server or have problems using RADIUS authentication.

802.1x Authentication using RADIUS

You must configure a primary EAP/802.1x Authentication server to use 802.1x security. A back-up server is optional.

NOTE
Each VLAN can be configured to use a separate RADIUS server (and backup server) for 802.1x authentication. 802.1x authentication (EAP authentication) can be separately enabled for each VLAN.

81

Performing Advanced Configuration RADIUS Accounting

Using an external RADIUS server, the AP can track and record the length of client sessions on the access point by sending RADIUS accounting messages per RFC2866. When a wireless client is successfully authenticated, RADIUS accounting is initiated by sending an Accounting Start request to the RADIUS server. When the wireless client session ends, an Accounting Stop request is sent to the RADIUS server.

Session Length
Accounting sessions continue when a client reauthenticates to the same AP. Sessions are terminated when: A client disassociates. A client does not transmit any data to the AP for a fixed amount of time. A client is detected on a different interface.

If the client roams from one AP to another, one session is terminated and a new session is begun.

NOTE
This feature requires RADIUS authentication using MAC Access Control or 802.1x. Wireless clients configured in the Access Points static MAC Access Control list are not tracked.

82

Performing Advanced Configuration

SSID/VLAN/Security
The AP provides several security features to protect your network from unauthorized access. Virtual Local Area Networks (VLANs) are logical groupings of network hosts. Defined by software settings, other VLAN members or resources appear (to clients) to be on the same physical segment, no matter where they are attached on the logical LAN or WAN segment. They simplify traffic flow between clients and their frequently-used or restricted resources. The AP uses Security Profiles to define allowed wireless clients, and authentication and encryption types and RADIUS Profiles to define RADIUS Servers used by the system or by a VLAN. The SSID/VLAN/Security tab contains the following sub-tabs: Management VLAN Security Profiles MAC Access Wireless-A and Wireless-B

Management VLAN
VLAN Overview
Virtual Local Area Networks (VLANs) are logical groupings of network hosts. Defined by software settings, other VLAN members or resources appear (to clients) to be on the same physical segment, no matter where they are attached on the logical LAN or WAN segment. They simplify traffic flow between clients and their frequently-used or restricted resources. VLANs now extend as far as the reach of the access point signal. Clients can be segmented into wireless sub-networks via SSID and VLAN assignment. A Client can access the network by connecting to an AP configured to support its assigned SSID/VLAN. AP devices are fully VLAN-ready; however, by default VLAN support is disabled. Before enabling VLAN support, certain network settings should be configured, and network resources such as a VLAN-aware switch, a RADIUS server, and possibly a DHCP server should be available. Once enabled, VLANs are used to conveniently, efficiently, and easily manage your network in the following ways: Manage adds, moves, and changes from a single point of contact Define and monitor groups Reduce broadcast and multicast traffic to unnecessary destinations Improve network performance and reduce latency Increase security Secure network restricts members to resources on their own VLAN Clients roam without compromising security

VLAN tagged data is collected and distributed through an AP's wireless interface(s) based on Network Name (SSID). An Ethernet port on the access point connects a wireless cell or network to a wired backbone. The access points communicate across a VLAN-capable switch that analyzes VLAN-tagged packet headers and directs traffic to the appropriate ports. On the wired network, a RADIUS server authenticates traffic and a DHCP server manages IP addresses for the VLAN(s). Resources like servers and printers may be present, and a hub may include multiple APs, extending the network over a larger area. In this figure, the numbered items correspond to the following components: 1. 2. 3. 4. 5. 6. 7. VLAN-enabled access point VLAN-aware switch (IEEE 802.1Q uplink) AP management via wired host (SNMP, Web interface or CLI) DHCP Server RADIUS Server VLAN 1 VLAN 2

83

Performing Advanced Configuration

Figure 4-23

Components of a typical VLAN

VLAN Workgroups and Traffic Management

Access Points that are not VLAN-capable typically transmit broadcast and multicast traffic to all wireless Network Interface Cards (NICs). This process wastes wireless bandwidth and degrades throughput performance. In comparison, VLAN-capable AP is designed to efficiently manage delivery of broadcast, multicast, and unicast traffic to wireless clients. The AP assigns clients to a VLAN based on a Network Name (SSID). The AP can support up to 16 VLAN/SSID pairs per radio (based on model type).

NOTE
The ability to configure up to 16 VLAN/SSID pairs and to configure a security profile per SSID is available only for 802.11b/g APs and 802.11a Upgrade Kit APs. 802.11b APs do not support multiple VLAN/SSID pairs. APs with the 802.11a card support multiple VLAN/SSID pairs, but do not support the security profile per SSID capability. The AP matches packets transmitted or received to a network name with the associated VLAN. Traffic received by a VLAN is only sent on the wireless interface associated with that same VLAN. This eliminates unnecessary traffic on the wireless LAN, conserving bandwidth and maximizing throughput. In addition to enhancing wireless traffic management, the VLAN-capable AP supports easy assignment of wireless users to workgroups. In a typical scenario, each user VLAN represents a workgroup; for example, one VLAN could be used for an EMPLOYEE workgroup and the other, for a GUEST workgroup. In this scenario, the AP would assign every packet it accepted to a VLAN. Each packet would then be identified as EMPLOYEE or GUEST, depending on which wireless NIC received it. The AP would insert VLAN headers or tags with identifiers into the packets transmitted on the wired backbone to a network switch. Finally, the switch would be configured to route packets from the EMPLOYEE workgroup to the appropriate corporate resources such as printers and servers. Packets from the GUEST workgroup could be restricted to a gateway that allowed access to only the Internet. A member of the GUEST workgroup could send and receive e-mail and access the Internet, but would be prevented from accessing servers or hosts on the local corporate network.

Typical User VLAN Configurations

VLANs segment network traffic into workgroups, which enable you to limit broadcast and multicast traffic. Workgroups enable clients from different VLANs to access different resources using the same network infrastructure. Clients using the same physical network are limited to those resources available to their workgroup.

84

Performing Advanced Configuration

The AP can segment users into a maximum of 16 different workgroups (32 if using two cards in a Dual-radio AP) based on an SSID/VLAN pair (also referred as a VLAN Workgroup or a Sub-network).

NOTE
The ability to configure up to 16 VLAN/SSID pairs and to configure a security profile per SSID is available only for 802.11b/g APs and 802.11a Upgrade Kit APs. 802.11b APs do not support multiple VLAN/SSID pairs. APs with the 802.11a card support multiple VLAN/SSID pairs, but do not support the security profile per SSID capability. The three primary scenarios for using VLAN workgroups are as follows: 1. VLAN disabled: Your network does not use VLANs, and you cannot configure the AP to use multiple SSIDs. 2. VLAN enabled, each VLAN workgroup uses a different VLAN ID Tag 3. VLAN enabled, a mixture of Tagged and Untagged workgroups

Enabling/Disabling VLAN Protocol

Control Access to the AP
Management access to the AP can easily be secured by making management stations or hosts and the AP itself members of a common VLAN. Simply configure a non-zero management VLAN ID and enable VLAN to restrict management of the AP to members of the same VLAN.

CAUTION
If a non-zero management VLAN ID is configured then management access to the AP is restricted to wired or wireless hosts that are members of the same VLAN. Ensure your management platform or host is a member of the same VLAN before attempting to manage the AP.

1. Click Configure > SSID/VLAN/Security. 2. Set the VLAN Management ID to a value between -1 and 4094 (a value of 0 disables VLAN management). 3. Place a check mark in the Enable VLAN Protocol box.

Provide Access to a Wireless Host in the Same Workgroup

The VLAN feature can allow wireless clients to manage the AP. If the VLAN Management ID matches a VLAN User ID, then those wireless clients who are members of that VLAN will have AP management access.

CAUTION
Once a VLAN Management ID is configured and is equivalent to one of the VLAN User IDs on the AP, all members of that User VLAN will have management access to the AP. Be careful to restrict VLAN membership to those with legitimate access to the AP.

1. Click Configure > SSID/VLAN/Security. 2. Set the VLAN Management ID to use the same VLAN ID as one of the configured SSID/VLAN pairs. See Typical User VLAN Configurations for details. 3. Place a check mark in the Enable VLAN Protocol box.

Disable VLAN Management

1. Click Configure > SSID/VLAN/Security. 2. Remove the check mark from the Enable VLAN Protocol box to disable all VLAN functionality.

85

Performing Advanced Configuration MAC Access

The MAC Access sub-tab allows you to build a list of stations, identified by their MAC addresses, authorized to access the network through the AP. The list is stored inside each AP within your network. Note that you must reboot the AP for any changes to the MAC Access Control Table to take effect. The MAC ACL Status parameter (configurable on the SSID/VLAN -> Wireless sub-tab) is per VLAN if VLAN Management is enabled. All other parameters besides MAC ACL Status are configured per AP, even if VLAN is enabled.

Configuring MAC Access

NOTE
MAC Access Control status is enabled or disabled when configuring each Security Profile. Operation Type: Choose between Passthru and Block. This determines how the stations identified in the MAC Access Control Table are filtered. If set to Passthru, only the addresses listed in the Control Table will pass through the bridge. If set to Block, the bridge will block traffic to or from the addresses listed in the Control Table. MAC Access Control Table: Click Add to create a new entry. Click Edit to change an existing entry. Each entry contains the following field: MAC Address: Enter the wireless clients MAC address. Comment: Enter an optional comment such as the clients name. Status: The entry is enabled automatically when saved (so the Status field is only visible when editing an entry). You can also disable or delete entries by changing this fields value.

NOTE
For larger networks that include multiple Access Points, you may prefer to maintain this list on a centralized location using the MAC Access Control Via RADIUS Authentication.

Figure 4-24

MAC Access Configuration Screen

86

Performing Advanced Configuration Security Profiles

The AP supports the following Security features: WEP Encryption: The original encryption technique specified by the IEEE 802.11 standard. 802.1x Authentication: An IEEE standard for client authentication. Wi-Fi Protected Access (WPA): A new standard that provides improved encryption security over WEP.

WEP Encryption
The IEEE 802.11 standards specify an optional encryption feature, known as Wired Equivalent Privacy or WEP, that is designed to provide a wireless LAN with a security level equal to what is found on a wired Ethernet network. WEP encrypts the data portion of each packet exchanged on an 802.11 network using an Encryption Key (also known as a WEP Key). When Encryption is enabled, two 802.11 devices must have the same Encryption Keys and both devices must be configured to use Encryption in order to communicate. If one device is configured to use Encryption but a second device is not, then the two devices will not communicate, even if both devices have the same Encryption Keys. An 802.11b AP supports 64-bit and 128-bit encryption: For 64-bit encryption, an encryption key is 10 hexadecimal characters (0-9 and A-F) or 5 ASCII characters (see ASCII Character Chart). For 128-bit encryption, an encryption key is 26 hexadecimal characters or 13 ASCII characters. An 802.11a or 802.11b/g AP supports 64-bit, 128-bit, and 152-bit encryption: For 64-bit encryption, an encryption key is 10 hexadecimal characters (0-9 and A-F) or 5 ASCII characters (see ASCII Character Chart). For 128-bit encryption, an encryption key is 26 hexadecimal characters or 13 ASCII characters. For 152-bit encryption, an encryption key is 32 hexadecimal characters or 16 ASCII characters.

802.1x Authentication
IEEE 802.1x is a standard that provides a means to authenticate and authorize network devices attached to a LAN port. A port in the context of IEEE 802.1x is a point of attachment to the LAN, either a physical Ethernet connection or a wireless link to an Access Point. 802.1x requires a RADIUS server and uses the Extensible Authentication Protocol (EAP) as a standards-based authentication framework, and supports automatic key distribution for enhanced security. The EAP-based authentication framework can easily be upgraded to keep pace with future EAP types. Popular EAP types include: EAP-Message Digest 5 (MD5): Username/Password-based authentication; does not support automatic key distribution EAP-Transport Layer Security (TLS): Certificate-based authentication (a certificate is required on the server and each client); supports automatic key distribution EAP-Tunneled Transport Layer Security (TTLS): Certificate-based authentication (a certificate is required on the server; a clients username/password is tunneled to the server over a secure connection); supports automatic key distribution PEAP - Protected EAP with MS-CHAP v2: Secure username/password-based authentication; supports automatic key distribution

Different servers support different EAP types and each EAP type provides different features. Refer to the documentation that came with your RADIUS server to determine which EAP types it supports.

NOTE
The AP supports the following EAP types when Authentication Mode is set to 802.1x, WPA or 802.11i (WPA2): EAP-TLS, PEAP, and EAP-TTLS. When Authentication Mode is set to Mixed, the AP supports the following EAP types: EAP-TLS, PEAP, EAP-TLLS, and EAP-MD5 (MD5 does not support automatic key distribution; therefore, if you choose this method you need to manually configure each client with the network's encryption key).

87

Performing Advanced Configuration

Authentication Process
There are three main components in the authentication process. The standard refers to them as: 1. 2. 3. supplicant (client PC) authenticator (Access Point) authentication server (RADIUS server)

When using Authentication Mode to 802.1x, WPA, Mixed mode (802.1x and WEP), or 802.11i, you need to configure your RADIUS server for authentication purposes. Prior to successful authentication, an unauthenticated client PC cannot send any data traffic through the AP device to other systems on the LAN. The AP inhibits all data traffic from a particular client PC until the client PC is authenticated. Regardless of its authentication status, a client PC can always exchange 802.1x messages in the clear with the AP (the client begins encrypting data after it has been authenticated).

Figure 4-25

RADIUS Authentication Illustrated

The AP acts as a pass-through device to facilitate communications between the client PC and the RADIUS server. The AP (2) and the client (1) exchange 802.1x messages using an EAPOL (EAP Over LAN) protocol (A). Messages sent from the client station are encapsulated by the AP and transmitted to the RADIUS (3) server using EAP extensions (B). Upon receiving a reply EAP packet from the RADIUS, the message is typically forwarded to the client, after translating it back to the EAPOL format. Negotiations take place between the client and the RADIUS server. After the client has been successfully authenticated, the client receives an Encryption Key from the AP (if the EAP type supports automatic key distribution). The client uses this key to encrypt data after it has been authenticated. For 802.11a and 802.11b/g clients that communicate with an AP, each client receives its own unique encryption key; this is known as Per User Per Session Encryption Keys.

Wi-Fi Protected Access (WPA)

Wi-Fi Protected Access (WPA) is a security standard designed by the Wi-Fi Alliance in conjunction with the Institute of Electrical and Electronics Engineers (IEEE). THE AP supports WPA2, based on the IEEE 802.11i security standard.

NOTE
For Dual-radio APs: WPA is available only for the AP-2000b/g and for APs using either an 802.11a or 802.11b/g Upgrade Kit. WPA is not available for APs with an 802.11b PC Card or a 5 GHz Upgrade Kit. WPA is a replacement for Wired Equivalent Privacy (WEP), the encryption technique specified by the original 802.11 standard. WEP has several vulnerabilities that have been widely publicized. WPA addresses these weaknesses and provides a stronger security system to protect wireless networks. WPA provides the following new security measures not available with WEP: Improved packet encryption using the Temporal Key Integrity Protocol (TKIP) and the Michael Message Integrity Check (MIC). Per-user, per-session dynamic encryption keys: Each client uses a different key to encrypt and decrypt unicast packets exchanged with the AP A client's key is different for every session; it changes each time the client associates with an AP The AP uses a single global key to encrypt broadcast packets that are sent to all clients simultaneously Encryption keys change periodically based on the Re-keying Interval parameter WPA uses 128-bit encryption keys

88

Performing Advanced Configuration

Dynamic Key distribution The AP generates and maintains the keys for its clients The AP securely delivers the appropriate keys to its clients Client/server mutual authentication 802.1x Pre-shared key (for networks that do not have an 802.1x solution implemented)

NOTE
For more information on WPA, see the Wi-Fi Alliance Web site at http://www.wi-fi.org. The AP supports the following WPA authentication modes: WPA: The AP uses 802.1x to authenticate clients. You should only use an EAP that supports mutual authentication and session key generation, such as EAP-TLS, EAP-TTLS, and PEAP. See 802.1x Authentication for details. WPA-PSK (Pre-Shared Key): For networks that do not have 802.1x implemented, you can configure the AP to authenticate clients based on a Pre-Shared Key. This is a shared secret that is manually configured on the AP and each of its clients. The Pre-Shared Key must be 256 bits long, which is 64 hexadecimal digits. The AP also supports a PSK Pass Phrase option to facilitate the creation of the Pre-Shared Key (so a user can enter an easy-to-remember phrase rather than a string of characters). 802.11i (also known as WPA2): The AP authenticates clients according to the 802.11i draft standard, using 802.1x authentication, an AES cipher, and re-keying. 802.11i-PSK (also known as WPA2 PSK): The AP uses an AES cipher, and authenticates clients based on a Pre-Shared Key. The Pre-Shared Key must be 256 bits long, which is either 64 hexadecimal digits. The AP also supports a PSK Pass Phrase option to facilitate the creation of the Pre-Shared Key (so a user can enter an easy-to-remember phrase rather than a string of characters).

Authentication Protocol Hierarchy

There is a hierarchy of authentication protocols defined for the AP. The hierarchy is as follows, from Highest to lowest: 802.1x authentication MAC Access Control via RADIUS Authentication MAC Access Control through individual APs' MAC Access Control Lists If you have both 802.1x and MAC authentication enabled, the 802.1x results will take effect. This is required in order to propagate the WEP keys to the clients in such cases. Once you disable 802.1x on the AP, you will see the effects of MAC authentication.

VLANs and Security Profiles

The AP2000 allows you to segment wireless networks into multiple sub-networks based on Network Name (SSID) and VLAN membership. A Network Name (SSID) identifies a wireless network. Clients associate with Access Points that share an SSID. During installation, the Setup Wizard prompts you to configure a Primary Network Name for each wireless interface. After initial setup and once VLAN is enabled, the AP can be configured to support up to 16 SSIDs per wireless interface to segment wireless networks based on VLAN membership. Each VLAN can be associated to a Security Profile and RADIUS Server Profiles. A Security Profile defines the allowed wireless clients, and authentication and encryption types. Refer to VLANs and Security Profiles for configuration details.

NOTE
The ability to configure up to 16 VLAN/SSID pairs and to configure a security profile per SSID is available only for 802.11b/g APs and 802.11a Upgrade Kit APs. 802.11b APs do not support multiple VLAN/SSID pairs. APs with the 802.11a card support multiple VLAN/SSID pairs, but do not support the security profile per SSID capability.

89

Performing Advanced Configuration

Configuring Security Profiles
Security policies can be configured and applied on the AP as a whole, or on a per VLAN basis. When VLAN is disabled on the AP, the user can configure a security profile for each interface of the AP. When VLANs are enabled and Security per SSID is enabled, the user can configure a security profile for each VLAN. The user defines a security policy by specifying one or more values for the following parameters: Wireless STA types (WPA station, 802.11i station, 802.1x station, WEP station) that can associate to the AP. Authentication mechanisms (802.1x, RADIUS MAC authentication) that are used to authenticate clients for each type of station. Cipher Suites (CCMP, TKIP, WEP) used for encapsulating the wireless data for each type of station.

Up to 16 security profiles can be configured per wireless interface. 1. Click Configure -> SSID/VLAN/Security -> Security Profile.

Figure 4-26

Security Profile Sub-tab

2. Click Add in the Security Profile Table to create a new entry. To modify an existing profile, select the profile and click Edit. To delete an existing profile, select the profile and click Delete. You cannot delete a Security Profile used in an SSID. Also, the first Security Profile (index 1.1 to 1.7) cannot be deleted. 3. Configure one or more types of wireless stations (security modes) that are allowed access to the AP under the security profile. The WEP/PSK parameters are separately configurable for each security mode. To enable a security mode in the profile (Non Secure Station, WEP Station, 802.1x Station, WPA Station, WPA-PSK Station, 802.11i Station, 802.11i-PSK Station), check the box next to the mode. See Figure 4-27 on page 92. If the security mode selected in a profile is WEP, WPA-PSK, or 802.11i-PSK, then you must configure the WEP or Pre-Shared Keys. 4. Configure the parameters as follows for each enabled security mode. Refer to Figure 4-27 on page 92. Non Secure Station: Authentication Mode: None. The AP allows access to Stations without authentication. Non secure station should be used only with WEP or 802.1x security mode. Cipher: None WEP Station: Authentication Mode: None Cipher: WEP Encryption Key 0, Encryption Key 1, Encryption Key 2, Encryption Key 3 Encryption Transmit Key: select Key 0, Key 1, Key 2, or Key 3

90

Performing Advanced Configuration

802.1x Station: Authentication Mode: 802.1x Cipher: WEP Encryption Key Length: 64 or 128 Bits. If 802.1x is enabled simultaneously with WEP, the 802.1x Stations encryption key length is determined by the WEP encryption key. WPA Station: Authentication Mode: 802.1x Cipher: TKIP WPA-PSK Station: Authentication Mode: PSK Cipher: TKIP PSK Passphrase: an 8-63 character user-defined phrase. It is recommended a passphrase of at least 13 characters, including both letters and numbers, and upper and lower case characters to ensure that the generated key cannot be easily deciphered by network infiltrators. 802.11i Station: Authentication Mode: 802.1x Cipher: AES 802.11i-PSK Station: Authentication Mode: PSK Cipher: AES PSK Passphrase: an 8-63 character user-defined phrase. It is recommended a passphrase of at least 13 characters, including both letters and numbers, and upper and lower case characters to ensure that the generated key cannot be easily deciphered by network infiltrators. 5. When finished configuring all parameters, click OK. 6. If you selected a Security Mode of 802.1x Station, WPA Station, or 802.11i Station, you must configure a RADIUS 802.1x/EAP server. Refer to the Configuring RADIUS Profiles section. Security Profile 1 will be used by default for all wireless interfaces. 7. Refer to the following section for advanced VLAN configuration options: Adding or Modifying an SSID/VLAN with VLAN Protocol Disabled and Adding or Modifying an SSID/VLAN with VLAN Protocol Enabled. 8. Reboot the AP.

91

Performing Advanced Configuration

Figure 4-27

Security Profile Table - Add Entries

92

Performing Advanced Configuration Wireless-A and Wireless-B

Each SSID/VLAN can have its own Security Profile that defines its security mode, authentication mechanism, and encryption, so that customers can have multiple types of clients (non-WEP, WEP, 802.1x, WPA) on the same system, but separated per VLAN. Refer to the Security Profiles section for more information. These parameters are configurable from the Wireless A and Wireless B sub-tabs.

Adding or Modifying an SSID/VLAN with VLAN Protocol Disabled

1. Click on SSID/VLAN/Security > Wireless-A or Wireless-B. This tab allows you to select the index of the SSID/VLAN to be added or edited. It also allows you to configure the RADIUS Accounting and Authentication Status, the MAC ACL Status, the Rekeying Interval, the Security Profile, and the RADIUS Server Profiles for the VLAN. 2. Scroll down to the SSID and VLAN table 3. Click Add to configure additional SSIDs, VLANs, and their associated security profiles and RADIUS server profiles, or click Edit to modify an existing VLAN/SSID. See Figure 4-28.

Figure 4-28

SSID and VLAN Table

The Add Entry or Edit Entry screen appears. See Figure 4-29 and Figure 4-30 on page 94.

Figure 4-29

SSID/VLAN Add Entries Screen (VLAN Protocol Disabled)

93

Performing Advanced Configuration

Figure 4-30

SSID/VLAN Edit Entries Screen (VLAN Protocol Disabled)

4. Enter a unique Network Name (SSID), between 1 and 32 characters. This parameter is mandatory. 5. Enter a unique VLAN ID. This parameter is mandatory. You must specify a unique VLAN ID for each SSID on the interface. A VLAN ID is a number from -1 to 4094. A value of -1 means that an entry is untagged. You can set the VLAN ID to -1 or untagged if you do not want clients that are using a specific SSID to be members of a VLAN workgroup. Only one untagged VLAN ID is allowed per interface. The VLAN ID must match an ID used by your network; contact your network administrator if you need assistance defining the VLAN IDs. 6. If editing an entry, enable or disable the VLAN using the Status drop-down menu. If adding an entry, this field will not appear. 7. Click OK to return to Wireless A or B Security Configuration Screen. See Figure 4-31 on page 95.

94

Performing Advanced Configuration

Figure 4-31

SSID, VLAN, and Security Data Configuration (VLAN Protocol Disabled)

8. Enable or disable RADIUS accounting on the VLAN/SSID under the Accounting Status drop-down menu. 9. Enable or disable RADIUS MAC authentication status on the VLAN/SSID under the RADIUS Authentication Status drop-down menu. 10. Enable or disable MAC Access Control List status on the VLAN/SSID under the MAC ACL Status drop-down menu. 11. Enter the Rekeying Interval in seconds. The default interval is 900 seconds. 12. Enter the Security Profile used by the VLAN in the Security Profile field. Refer to the Security Profiles section for more information.

NOTE
If you have two or more SSIDs per interface using a security Profile with a security mode of Non Secure, be aware that security being applied in the VLAN is not being applied in the wireless network.

95

Performing Advanced Configuration

13. Define the RADIUS Server Profile Configuration for the VLAN/SSID: RADIUS MAC Authentication Profile RADIUS EAP Authentication Profile RADIUS Accounting Profile If 802.1x, WPA, or 802.11i security mode is used, the RADIUS EAP Authentication Profile must have a value. A RADIUS Server Profile for authentication for each VLAN shall be configured as part of the configuration options for that VLAN. RADIUS profiles are independent of VLANs. The user can define any profile to be the default and associate all VLANs to that profile. Four profiles are created by default, MAC Authentication, EAP Authentication, Accounting, and Management. 14. Reboot the AP.

Adding or Modifying an SSID/VLAN with VLAN Protocol Enabled

1. Click SSID/VLAN/Security > Wireless-A or Wireless-B. This tab allows you to select the index of the SSID/VLAN to be added or edited. It also allows you to enable Security Per SSID, and configure the RADIUS Accounting and Authentication Status, the MAC ACL Status, the Rekeying Interval, the Security Profile, and the RADIUS Server Profiles for the VLAN. 2. Select the Enable Security Per SSID option. The screen will update to the following:

Figure 4-32

SSID/VLAN Configuration (VLAN Protocol Enabled)

3. Click Add to configure additional SSIDs, VLANs, and their associated security profiles and RADIUS server profiles, or click Edit to modify an existing VLAN/SSID.

96

Performing Advanced Configuration

The Add Entry or Edit Entry screen appears. See Figure 4-33 below and Figure 4-34 on page 98.

Figure 4-33

SSID/VLAN Add Entries Screen (VLAN Protocol Enabled)

97

Performing Advanced Configuration

Figure 4-34

SSID/VLAN Edit Entries Screen (VLAN Protocol Enabled)

4. Enter a unique Network Name (SSID), between 1 and 32 characters. This parameter is mandatory. 5. Enter a unique VLAN ID. This parameter is mandatory. You must specify a unique VLAN ID for each SSID on the interface. A VLAN ID is a number from -1 to 4094. A value of -1 means that an entry is untagged. You can set the VLAN ID to -1 or untagged if you do not want clients that are using a specific SSID to be members of a VLAN workgroup. Only one untagged VLAN ID is allowed per interface. The VLAN ID must match an ID used by your network; contact your network administrator if you need assistance defining the VLAN IDs. 6. If editing an entry, enable or disable the VLAN using the VLAN Status drop-down menu. If adding, this drop-down menu will not appear. 7. Enable or disable the SSID Authorization status from the drop-down menu. SSID Authorization is the RADIUS based authorization of the SSID for a particular client. The authorized SSIDs are sent as the tunnel attributes. 8. Enable or disable RADIUS accounting on the VLAN/SSID under the Accounting Status drop-down menu. 9. Enable or disable RADIUS MAC authentication status on the VLAN/SSID under the RADIUS Authentication Status drop-down menu. 10. Enable or disable MAC Access Control List status on the VLAN/SSID under the MAC ACL Status drop-down menu. 11. Enter the Rekeying Interval in seconds. The default interval is 900 seconds. 12. Enter the Security Profile used by the VLAN in the Security Profile field.

98

Performing Advanced Configuration

NOTE
If you have two or more SSIDs per interface using a security Profile with a security mode of Non Secure, be aware that security being applied in the VLAN is not being applied in the wireless network. 13. Define the RADIUS Server Profile Configuration for the VLAN/SSID: RADIUS MAC Authentication Profile RADIUS EAP Authentication Profile RADIUS Accounting Profile If 802.1x, WPA, or 802.11i security mode is used, the RADIUS EAP Authentication Profile must have a value. A RADIUS Server Profile for authentication for each VLAN shall be configured as part of the configuration options for that VLAN. RADIUS profiles are independent of VLANs. The user can define any profile to be the default and associate all VLANs to that profile. Four profiles are created by default, MAC Authentication, EAP Authentication, Accounting, and Management. 14. Reboot the AP.

Broadcast SSID and Closed System

Broadcast SSID allows the broadcast of a single SSID when the AP is configured for multiple SSIDs. Broadcast SSID may only be enabled for a single SSID. This object can only be configured using the CLI and SNMP using a MIB browser or network management application. Closed System manages the way probe requests are handled. If enabled, the AP will respond to probe requests with an SSID only if the client has specified the SSID in the probe request. If the client sends a probe request with a null or ANY SSID, the AP will respond with a null SSID. If disabled, the AP will respond with each configured SSID, whether or not an SSID has been specified in the probe request. This option is disabled by default. To enable Closed System, click on Interfaces > Wireless-A or Wireless-B and check the Enable Closed System box. For more information, on Broadcast SSID and Closed System, refer to Technical Bulletin 69680 at http://support.proxim.com.

99

Monitoring the AP-2000

Logging into the HTTP Interface Version: Provides version information for the Access Points system components. ICMP: Displays statistics for Internet Control Message Protocol packets sent and received by the AP. IP/ARP Table: Displays the APs IP Address Resolution table. Learn Table: Displays the list of nodes that the AP has learned are on the network. IAPP: Provides statistics for the Inter-Access Point Protocol messages sent and received by the AP. RADIUS: Provides statistics for the configured primary and backup RADIUS server(s). Interfaces: Displays the Access Points interface statistics (Wireless and Ethernet). Station Statistics: Displays statistics for stations and Wireless Distribution System links.

Logging into the HTTP Interface

Once the AP has a valid IP Address and an Ethernet connection, you may use your web browser to monitor network statistics. The Command Line Interface (CLI) also provides a method for viewing network statistics using Telnet or a serial connection. This section covers only use of the HTTP interface. For more information about viewing network statistics with the CLI, refer to Using the Command Line Interface (CLI). Follow these steps to monitor an APs operating statistics using the HTTP interface: 1. Open a Web browser on a network computer.

NOTE
The HTTP interface supports the following Web browser: Microsoft Internet Explorer 6 with Service Pack 1 or later Netscape 6.1 or later 2. If necessary, disable the Internet proxy settings. For Internet Explorer users, follow these steps: Select Tools > Internet Options.... Click the Connections tab. Click LAN Settings.... If necessary, remove the check mark from the Use a proxy server box. Click OK twice to save your changes and return to Internet Explorer. 3. Enter the Access Points IP address in the browsers Address field and press Enter. Result: The AP Enter Network Password screen appears. 4. Enter the HTTP password in the Password field and click OK. Leave the User Name field blank. (By default, the HTTP password is public). Result: The System Status screen appears.

100

Monitoring the AP-2000

Figure 5-1

Enter Network Password Screen

5. Click the Monitor button located on the left-hand side of the screen.

Figure 5-2

Monitor Main Screen

6. Click the tab that corresponds to the statistics you want to review. For example, click Learn Table to see the list of nodes that the AP has discovered on the network. 7. If applicable, click the Refresh button to update the statistics.

101

Monitoring the AP-2000

Version
From the HTTP interface, click the Monitor button and select the Version tab. The list displayed provides you with information that may be pertinent when calling Technical Support. With this information, your Technical Support representative can verify compatibility issues and make sure the latest software are loaded. This screen displays the following information for each Access Point component: Serial Number: The components serial number, if applicable. Component Name ID: The AP identifies a system component based on its ID. Each component has a unique identifier. Variant: Several variants may exist of the same component (for example, a hardware component may have two variants, one with more memory than the other). Version: Specifies the components version or build number. The Software Image version is the most useful information on this screen for the typical end user.

Figure 5-3

Version Information Screen

102

Monitoring the AP-2000

ICMP
This tab provides statistical information for both received and transmitted messages directed to the AP. Not all ICMP traffic on the network is counted in the ICMP (Internet Control Message Protocol) statistics.

Figure 5-4

ICMP Monitoring Screen

IP/ARP Table
This tab provides information based on the Address Resolution Protocol (ARP), which relates MAC Address and IP Addresses.

Figure 5-5

IP/ARP Table

103

Monitoring the AP-2000

Learn Table
This tab displays information relating to network bridging. It reports the MAC address for each node that the device has learned is on the network and the interface on which the node was detected. There can be up 10,000 entries in the Learn Table.

Figure 5-6

Learn Table

IAPP
This tab displays statistics relating to client handovers and communications between ORiNOCO Access Points.

Figure 5-7

IAPP Screen

104

Monitoring the AP-2000

RADIUS
This tab provides RADIUS authentication, EAP/802.1x authentication, and accounting information for both the Primary and Backup RADIUS servers.

NOTE
RADIUS authentication and accounting must be enabled for this information to be valid.

Figure 5-8

RADIUS Monitoring Screen

105

Monitoring the AP-2000

Interfaces
This tab displays statistics for the Ethernet and wireless interfaces. The Operational Status can be up, down, or testing.

Figure 5-9

Wireless Interface Monitoring

106

Monitoring the AP-2000

Station Statistics
This tab displays information on wireless clients attached to the AP and on Wireless Distribution System links.

Enabling and Viewing Station Statistics

To enable the monitoring of Stations Statistics, perform the following procedure: 1. Click on the Monitor tab on the left on the web page. 2. Click on the Station Statistics tab on the Monitor screen. 3. Enable the Monitoring Station Statistics feature (Station Statistics are disabled by default) by checking Enable Monitoring Station Statistics and click OK. You do not need to reboot the AP for the changes to take effect. If clients are connected to the device or WDS links are configured for the device, the statistics will now be shown on the screen.

Refreshing Station Statistics

Click on the Refresh button in the browser window to view the latest statistics. If any new clients associate to the AP, you can see the statistics of the new clients after you click the refresh button.

Figure 5-10

Station Statistics Screen

Description of Station Statistics

The following stations statistics are displayed: MAC Address: The MAC address of the wireless client for which the statistics are gathered. For WDS links, this is the partner MAC address of the link. IP Address: The IP address of the associated wireless station for which the Statistics are gathered. (0.0.0.0 for WDS links)

107

Monitoring the AP-2000

Interface to which the Station is connected: The interface number on which the client is connected with the AP. For WDS links this is the interface on which the link is configured. Station Type: The type of wireless client (STA or WDS). MAC Protocol: The MAC protocol for this wireless client (or WDS link partner). The possible values are 802.11a, 802.11b, 802.11g Signal / Noise: The Signal /Noise Level measured at the AP when frames are received from the associated wireless station (or WDS link partner) Time since Last Packet Received: The time elapsed since the last frame from the associated wireless station (or WDS link partner) was received. Number of Clients: The number of stations and WDS links monitored. The following stations statistics are not displayed in the Graphical User Interface, but can be viewed from a MIB browser: Octets Received: The number of octets received from the associated wireless station (or WDS link partner) by the AP. Unicast Frames Received: The number of Unicast frames received from the associated wireless station (or WDS link partner) by the AP. Non-Unicast Frames Received: The number of Non-Unicast frames received (i.e. broadcast or multicast) from the associated wireless station (or WDS link partner) by the AP. Octets Transmitted: The number of octets sent to the associated wireless station (or WDS link partner) from the AP. Unicast Frames Transmitted: The number of Unicast frames transmitted to the associated wireless station (or WDS link partner) from the AP.

108

Performing Commands

Logging into the HTTP Interface Introduction to File Transfer via TFTP or HTTP: Describes the available file transfer methods. Update AP via TFTP: Download files from a TFTP server to the AP. Update AP via HTTP: Download files to the AP from HTTP. Retrieve File via TFTP: Upload configuration files from the AP to a TFTP server. Retrieve File via HTTP: Upload configuration files from the AP via HTTP. Reboot: Reboot the AP in the specified number of seconds. Reset: Reset all of the Access Points configuration settings to factory defaults. Help Link: Configure the location where the AP Help files can be found.

Logging into the HTTP Interface

Once the AP has a valid IP Address and an Ethernet connection, you may use your web browser to issue commands. The Command Line Interface (CLI) also provides a method for issuing commands using Telnet or a serial connection. This section covers only use of the HTTP Interface. For more information about issuing commands with the CLI, refer to Using the Command Line Interface (CLI). Follow these steps to view the available commands supported by the APs HTTP interface: 1. Open a Web browser on a network computer.

NOTE
The HTTP interface supports the following Web browser: Microsoft Internet Explorer 6 with Service Pack 1 or later Netscape 6.1 or later 2. If necessary, disable the Internet proxy settings. For Internet Explorer users, follow these steps: Select Tools > Internet Options.... Click the Connections tab. Click LAN Settings.... If necessary, remove the check mark from the Use a proxy server box. Click OK twice to save your changes and return to Internet Explorer. 3. Enter the Access Points IP address in the browsers Address field and press Enter. Result: The Enter Network Password screen appears. 4. Enter the HTTP password in the Password field and click OK. Leave the User Name field blank. (By default, the HTTP password is public). Result: The System Status screen appears.

109

Performing Commands

Figure 6-1

Enter Network Password Screen

5. Click the Commands button located on the left-hand side of the screen.

Figure 6-2

Commands Main Screen

6. Click the tab that corresponds to the command you want to issue. For example, click Reboot to restart the unit.

110

Performing Commands

Introduction to File Transfer via TFTP or HTTP

There are two methods of transferring files to or from the AP, TFTP or HTTP (or HTTPS if enabled). The following procedures describe downloading Configuration, AP Image, Bootloader, Private Key, and Certificate files to the AP: Update AP via TFTP Update AP via HTTP Retrieve File via TFTP Retrieve File via HTTP

The following procedures describe uploading Configuration files from the AP:

TFTP File Transfer Guidelines

A TFTP server must be running and configured to point to the directory containing the file. If you do not have a TFTP server installed on your system, install the TFTP server from the ORiNOCO CD.

HTTP File Transfer Guidelines

HTTP file transfer can be performed either with or without SSL enabled. HTTP file transfers with SSL require enabling Secure Management and Secure Socket Layer. HTTP transfers that use SSL may take additional time.

NOTE
SSL requires Internet Explorer version 6, 128 bit encryption, Service Pack 1, and patch Q323308.

Image Error Checking during File Transfer

The Access Point performs checks to verify that an image downloaded through HTTP or TFTP is valid. The following checks are performed on the downloaded image: Zero Image size Large image size Non VxWorks image AP image Digital signature verification

If any of the above checks fail on the downloaded image, the Access Point deletes the downloaded image and retains the old image. Otherwise, if all checks pass successfully, the AP deletes the old image and retains the downloaded image. These checks are to ensure that the AP does not enter an invalid image state. The storage of the two images is only temporary to ensure the proper verification; the two images will not be stored in the AP permanently. Image error checking functions automatically in the background. No user configuration is required.

111

Performing Commands

Update AP via TFTP

Use the Update AP via TFTP tab to download Configuration, AP Image, Bootloader files, and Certificate and Private Key files to the AP. A TFTP server must be running and configured to point to the directory containing the file.

Figure 6-3

Update AP via TFTP Command Screen

If you do not have a TFTP server installed on your system, install the TFTP server from the ORiNOCO CD. You can either install the TFTP server from the CD Wizard or run OEM-TFTP-Server.exe found in the CDs Xtras/SolarWinds sub-directory. The Update AP via TFTP tab shows version information and allows you to enter TFTP information as described below. Server IP Address: Enter the TFTP server IP Address. Double-click the TFTP server icon on your desktop and locate the IP address assigned to the TFTP server. Note: This is the IP address that will be used to point the Access Point to the AP Image file. File Name: Enter the name of the file to be downloaded (including the file extension). Copy the updated AP Image file to the TFTP servers root folder. The default AP Image is located at C:/Program Files/ORiNOCO/AP/. File Type: Select the proper file type. Choices include: Config for configuration information, such as System Name, Contact Name, and so on. Image for the AP Image (executable program). UpgradeBspBl for the Bootloader software. SSL Certificate: the digital certificate for authentication in SSL communications. SSL Private Key: the private key for encryption in SSL communications. SSH Public Key: the public key in SSH communications. Refer to Secure Shell (SSH) for more information. SSH Private Key: the private key in SSH communications. Refer to Secure Shell (SSH) for more information. CLI Batch File: a CLI Batch file that contains CLI commands to configure the AP. This file will be executed by the AP immediately after being uploaded. Refer to CLI Batch File for more information. File Operation: Select either Update AP or Update AP & Reboot. You should reboot the AP after downloading files.

112

Performing Commands

Update AP via HTTP

Use the Update AP via HTTP tab to download Configuration, AP Image, Bootloader files, and Certificate and Private Key files to the AP. Once on the Update AP screen, click on the via HTTP tab.

Figure 6-4

Update AP via HTTP Command Screen

The Update AP via HTTP tab shows version information and allows you to enter HTTP information as described below. Select the File Type that needs to be updated from the drop-down box. Choices include: Config for configuration information, such as System Name, Contact Name, and so on. Image for the AP Image (executable program). Upgrade BSPBL: for the Bootloader software. SSL Certificate: the digital certificate for authentication in SSL communications. SSL Private Key: the private key for encryption in SSL communications. SSH Public Key: the public key in SSH communications. Refer to Secure Shell (SSH) for more information. SSH Private Key: the private key in SSH communications. Refer to Secure Shell (SSH) for more information. CLI Batch File: a CLI Batch file that contains CLI commands to configure the AP. This file will be executed by the AP immediately after being uploaded. Refer to CLI Batch File for more information.

Use the Browse button or manually type in the name of the file to be downloaded (including the file extension) in the File Name field. If typing the file name, you must include the full path and the file extension in the file name text box. To initiate the HTTP Update operation, click the Update AP button. A warning message gets displayed that advises the user that a reboot of the device will be required for changes to take effect.

113

Performing Commands
Figure 6-5 Warning Message

Click OK to continue with the operation or Cancel to abort the operation.

NOTE
An HTTP file transfer using SSL may take extra time. If the operation completes successfully the following screen appears.

Figure 6-6

Update AP Successful

If the operation did not complete successfully the following screen appears, and the reason for the failure is displayed.

Figure 6-7

Update AP Unsuccessful

114

Performing Commands

Retrieve File via TFTP

Use the Retrieve File via TFTP tab to upload files from the AP to the TFTP server. The TFTP server must be running and configured to point to the directory to which you want to copy the uploaded file. We suggest you assign the file a meaningful name, which may include version or location information. If you dont have a TFTP server installed on your system, install the TFTP server from the ORiNOCO CD. You can either install the TFTP server from the CD Wizard or run OEM-TFTP-Server.exe found in the CDs Xtras/SolarWinds sub-directory. The Retrieve AP via TFTP tab shows version information and allows you to enter TFTP information as described below. Server IP Address: Enter the TFTP server IP Address. Double-click the TFTP server icon on your desktop and locate the IP address assigned to the TFTP server. File Name: Enter the name of the file to be uploaded. File Type: Select the type of file to be uploaded: Config file, CLI Batch File, or CLI Batch (Error) Log.

NOTE
Use the following procedure to retrieve a file from an AP to a TFTP server: 1. If retrieving a Configuration file, configure all the required parameters in their respective tabs. Reboot the device. 2. Retrieve and store the file. Click the Retrieve File button to initiate the upload of the file from the AP to the TFTP server. 3. If you retrieved a Configuration file, update the file as necessary. 4. If you retrieved a CLI Batch File or CLI Batch Log, you can examine the file using a standard text editor. For more information on CLI Batch Files, refer to CLI Batch File.

Figure 6-8

Retrieve File via TFTP Command Screen

115

Performing Commands

Retrieve File via HTTP

Use the Retrieve File via HTTP tab to retrieve configuration files, CLI Batch Files, or CLI Batch Logs from the AP. Select the type of file (Config, CLI Batch File, or CLI Batch Log) from the File Type drop-down menu. For more information on CLI Batch Files and CLI Batch Logs refer to CLI Batch File.

Figure 6-9

Retrieve File via HTTP Command Screen

A confirmation message gets displayed that asks if the user wants to proceed with retrieving the file. Click OK to continue with the operation or Cancel to abort the operation.

Figure 6-10

Retrieve File Confirmation Dialog

116

Performing Commands

Figure 6-11

File Download Dialog Box

On clicking the Save button the following Save As window displays, where the user is prompted to choose the filename and location where the file is to be downloaded. Select an appropriate filename and location and click OK.

Figure 6-12

Retrieve File Save As Dialog

117

Performing Commands

Reboot
Use the Reboot tab to save configuration changes (if any) and reset the AP. Entering a value of 0 (zero) seconds causes an immediate reboot. Note that Reset, described below, does not save configuration changes.

CAUTION
Rebooting the AP will cause all users who are currently connected to lose their connection to the network until the AP has completed the restart process and resumed operation.

Figure 6-13

Reboot Command Screen

118

Performing Commands

Reset
Use the Reset tab to restore the AP to factory default conditions. The AP may also be reset from the RESET button located on the side of the unit. Since this will reset the Access Points current IP address, a new IP address must be assigned. Refer to Recovery Procedures for more information.

CAUTION
Resetting the AP to its factory default configuration will permanently overwrite all changes that have made to the unit. The AP will reboot automatically after this command has been issued.

Figure 6-14

Reset to Factory Defaults Command Screen

119

Performing Commands

Help Link
To open Help, click the Help button on any display screen. During initialization, the AP on-line help files are downloaded to the default location: C:/Program Files/ORiNOCO/AP/HTML/index.htm.

NOTE
Use the forward slash character ("/") rather than the backslash character ("\") when configuring the Help Link location.

NOTE
Add the APs management IP address into the Internet Explorer list of Trusted Sites. The ORiNOCO AP Help information is available in English, French, German, Italian, Spanish, and Japanese. The Help files are copied to your computer in one language only. If you want to place these files on a shared drive, copy the Help Folder to the new location, and then specify the new path in the Help Link box.

Figure 6-15

Help Link Configuration Screen

120

Troubleshooting the AP-2000

Troubleshooting Concepts Symptoms and Solutions Recovery Procedures Related Applications

NOTE
This section helps you locate problems related to the AP device setup. For details about RADIUS, TFTP, serial communication programs (such as HyperTerminal), Telnet applications, or web browsers, please refer to the documentation that came with the application for assistance.

Troubleshooting Concepts
The following list identifies important troubleshooting concepts and topics. The most common initialization and installation problems relate to IP addressing. For example, you must have valid IP addresses for both the AP and the management computer to access the units HTTP interface. IP Address management is fundamental. Factory default units are set for Dynamic (DHCP) IP Address assignment. The default IP address for the AP is 10.0.0.1 if your network does not have a DHCP server. If you connect the AP to a network with an active DHCP server, then use ScanTool to locate the IP address of your unit. If a DHCP server is not active on your subnet, then use ScanTool to assign a static IP address to the unit. The Trivial File Transfer Protocol (TFTP) provides a means to download and upload files. These files include the AP Image (executable program) and configuration files. If the AP password is lost or forgotten, you will need to reset to default values. The Reset to Factory Default Procedure resets configuration, but does not change the current AP Image. If all else fails Use the Forced Reload Procedure to erase the current AP Image and then download a new image. Once the new image is loaded, use the Reset to Factory Default Procedure to set the unit to factory default values and reconfigure the unit. The AP Supports a Command Line Interface (CLI). If you are having trouble locating your AP on the network, connect to the unit directly using the serial interface and refer to Using the Command Line Interface (CLI) for CLI command syntax and parameter names.

121

Troubleshooting the AP-2000

Symptoms and Solutions

Connectivity Issues
Connectivity issues include any problem that prevents you from powering up or connecting to the AP.

AP Unit Will Not Boot - No LED Activity

1. Make sure your power source is operating. 2. Make sure all cables are connected to the AP correctly. 3. If you are using Active Ethernet, make sure you are using a Category 5, foiled, twisted pair cable to power the AP.

Serial Link Does Not Work

1. Make sure you are using a standard, straight-through, 9-pin serial cable. 2. Double-check the physical network connections. 3. Make sure your PC terminal program (such as HyperTerminal) is active and configured to the following values: Com Port: (COM1, COM2, etc. depending on your computer); Baud rate: 9600; Data bits: 8; Stop bits: 1; Flow Control: None; Parity: None; Line Feeds with Carriage Returns (In HyperTerminal select: File -> Properties -> Settings -> ASCII Setup -> Send Line Ends with Line Feeds)

Ethernet Link Does Not Work

1. Double-check the physical network connections. Use a known-good unit to make sure the network connection is present. Once you have the AP IP address, you can use the Ping command over Ethernet to test the IP Address. If the AP responds to the Ping, then the Ethernet Interface is working properly. 2. By default, the Access Point will attempt to automatically detect the Ethernet settings. However, if you are having problems with the Ethernet link, manually configure the Access Points Ethernet settings. For example, if your switch operates at 100 Mbits/sec/Full Duplex, manually configure the Access Point to use these settings (see Ethernet). If you cannot access the unit over Ethernet, then use the CLI interface over the serial port to configure the Ethernet port (see Using the Command Line Interface (CLI) and Set Ethernet Speed and Transmission Mode). 3. Perform network infrastructure troubleshooting (check switches, routers, etc.).

Basic Software Setup and Configuration Problems

Lost AP, Telnet, or SNMP Password
1. Perform the Reset to Factory Default Procedure in this guide. This procedure resets system and network parameters, but does not affect the AP Image. The default AP HTTP password is public, and the default Telnet password is also public.

Client Computer Cannot Connect

1. Client computers should have the same Network Name and security settings as the AP. 2. Network Names should be allocated and maintained by the Network Administrator. 3. Refer to the documentation that came with your client card for additional troubleshooting suggestions.

AP Has Incorrect IP Address

1. Default IP Address Assignment mode is dynamic (DHCP). If you do not have a DHCP server on your network, the default IP Address is 10.0.0.1. If you have more than one unintialized AP connected to the network, they will all have the same default IP address and you will not be able to communicate with them (due to an IP address conflict). In this case, assign each AP a static IP address via the serial cable or turn off all units but one and change the IP address using ScanTool one at a time.

122

Troubleshooting the AP-2000

2. The AP only contacts a DHCP server during boot-up. If your networks DHCP server is not available while the AP is booting, the device will retain the last IP Address it had. Reboot the AP once your DHCP server is on-line again or use the ScanTool to find the Access Points current IP address. 3. To find the units current IP address if using DHCP, open the IP Client Table in the DHCP Server and match the Access Points IP address to its MAC address (found on the product label). Alternatively, use ScanTool to identify an Access Points current IP address. 4. Once you have the current IP address, use the HTTP or CLI Interface to change the units IP settings, if necessary. 5. If you use static IP Address assignments, and cannot access the unit over Ethernet, use the Initializing the IP Address using CLI procedure. Once the IP Address is set, you can use the Ethernet Interface to complete configuration. 6. Perform the Reset to Factory Default Procedure in this guide. This will reset the unit to DHCP mode. If there is a DHCP Server on the network, the DHCP Server will assign an IP Address to the AP.

HTTP (browser) or Telnet Interface Does Not Work

1. Make sure you are using a compatible browser: Microsoft Internet Explorer 6 with Service Pack 1 or later Netscape 6.1 or later 2. Make sure you have the proper IP address. Enter your Access Points IP Address in the browser address bar, similar to this example: http://192.168.1.100 When the Enter Network Password window appears, leave the User Name field empty and enter the HTTP password in the Password field. The default HTTP password is public. 3. Use the CLI over the serial port to check the IP Access Table, which can be restricting access to Telnet and HTTP.

HTML Help Files Do Not Appear

1. Verify that the HTML Help files are installed in the default directory: C:\Program Files\ORiNOCO\AP\HTML\ 2. If the Help files are not located in this folder, contact your network administrator to find out where the Help files are located on your server. 3. Perform the following steps to verify the location or to enter the pathname for the Help files: a. Click the Commands button in the HTTP interface. b. Select the Help tab located at the top of the screen. c. Enter the pathname where the Help files are located in the Help Link box. d. Click OK when finished.

Telnet CLI Does Not Work

1. Make sure you have the proper IP Address. Enter your AP IP address in the Telnet connection dialog, from a DOS prompt, type: C:\> telnet <AP IP Address> 2. Confirm that your computer has an IP address in the same IP subnet as your Access Point. 3. Use the CLI over the serial port to check the IP Access Table, which can be restricting access to Telnet and HTTP.

TFTP Server Does Not Work

1. Make sure the TFTP Server has been started. 2. Verify the IP address of the TFTP Server. The server may be local or remote, so long as it has a valid IP address. 3. Configure the TFTP Server to point to the folder containing the file to be downloaded (or to the folder in which the file is to be uploaded). 4. Verify that you have entered the proper AP Image file name (including the file extension) and directory path. 5. If you have a problem uploading a file, verify that the TFTP server is configured to allow uploads (typically the default setting is to allow only downloads).

123

Troubleshooting the AP-2000 Client Connection Problems

Client Software Finds No Connection
Make sure you have configured your client software with the proper Network Name and Security settings. Network Names and WEP Keys are typically allocated and maintained by your network administrator.

Client PC Card Does Not Work

1. Make sure you are using the latest PC Card driver software. 2. Download and install the latest ORiNOCO client software from http://www.proxim.com.

Intermittent Loss of Connection

1. Make sure you are within range of an active AP. 2. You can check the signal strength using the signal strength gauge on your client software.

Client Does Not Receive an IP Address - Cannot Connect to Internet

1. If the AP is configured as a DHCP server, open the Web-browser Interface and select the Configure button and then the Network tab to make sure the proper DHCP settings are being used. 2. If you are not using the DHCP server feature on the AP, then make sure that your local DHCP server is accessible from the Access Points subnet. 3. From the client computer, use the ping network command to test the connection with the AP. If the AP responds, but you still cannot connect to the Internet, there may be a physical network configuration problem (contact your network support staff). 4. If using Active Ethernet, make sure you are not using a crossover Ethernet cable between the AP and the hub.

VLAN Operation Issues

Verifying Proper Operation of the VLAN Feature
The correct VLAN configuration can be verified by pinging both wired and wireless hosts from both sides of the AP device and the network switch. Traffic can be sniffed on both the wired (Ethernet) and wireless (WDS) backbones (if configured). Bridge frames generated by wireless clients and viewed on one of the backbones should contain IEEE 802.1Q compliant VLAN headers or tags. The VLAN ID in the headers should correspond to one of the VLAN User IDs configured for the AP.

NOTE
16 VLAN/SSID pairs are available for 802.11b/g APs and APs with an 11a Upgrade Kit. 802.11b APs and APs with a 5 GHz Upgrade Kit only support one VLAN/SSID pair.

VLAN Workgroups
The correct VLAN assignment can be verified by pinging the AP to ensure connectivity, by pinging the switch to ensure VLAN properties, and by pinging hosts past the switch to confirm the switch is functional. Ultimately, traffic can be sniffed on the Ethernet or WDS interfaces (if configured) using third-party packages. Most problems can be avoided by ensuring that 802.1Q compliant VLAN tags containing the proper VLAN ID have been inserted in the bridged frames. The VLAN ID in the header should correspond to the users assigned network name.

What if network traffic is being directed to a nonexistent host?

All sessions are disconnected, traffic is lost, and a manual override is necessary Workaround: you can configure the switch to mimic the nonexistent host

124

Troubleshooting the AP-2000

I have just configured the Management ID and now I can't manage the AP?
Check to ensure your password is correct. If your password is incorrect or all inbound packets do NOT have the correct tag, then a manual override is necessary.

CAUTION
The manual override process disconnects all users and resets all values to factory defaults.

Active Ethernet (AE)

The AP Does Not Work
1. Verify that you are using a standard UTP Category 5 cable. 2. Try a different port on the same AE hub (remember to move the input port accordingly) if it works, there is probably a faulty port or bad RJ-45 port connection. 3. If possible, try to connect the AP to a different AE hub. 4. Try using a different Ethernet cable if it works, there is probably a faulty connection over the long cable, or a bad RJ-45 connection. 5. Check power plug and hub. 6. If the Ethernet link goes down, check the cable, cable type, switch, and hub.

There Is No Data Link

1. Verify that the indicator for the port is on. 2. Verify that the AE hub is connected to the Ethernet network with a good connection. 3. Verify that the Ethernet cable is Category 5 or better and is less than 100 meters (approximately 325 feet) in length from the Ethernet source to the AP. 4. Try to connect a different device to the same port on the AE hub if it works and a link is established, there is probably a faulty data link in the AP. 5. Try to re-connect the AP to a different output port (remember to move the input port accordingly) if it works, there is probably a faulty output or input port in the AE hub or a bad RJ-45 connection.

Overload Indications
1. Verify that you are not using a cross-over cable between the AE output port and the AP. 2. Verify that there is no short over any of the twisted pair cables. 3. Move the device into a different output port if it works, there is probably a faulty port or bad RJ-45 connection.

Recovery Procedures
The most common installation problems relate to IP addressing. For example, without the TFTP server IP Address, you will not be able to download a new AP Image to the AP. IP Address management is fundamental. We suggest you create a chart to document and validate the IP addresses for your system. If the password is lost or forgotten, you will need to reset the AP to default values. The Reset to Factory Default Procedure resets configuration settings, but does not change the current AP Image. If the AP has a corrupted software image, follow the Forced Reload Procedure to erase the current AP Image and download a new image.

125

Troubleshooting the AP-2000 Reset to Factory Default Procedure

Use this procedure to reset the network configuration values, including the Access Points IP address and subnet mask. The current AP Image is not deleted. Follow this procedure if you forget the Access Points password: 1. Press and hold the RELOAD button for 10 seconds.

NOTE
See RELOAD and RESET Buttons to identify the buttons. You need to use a pin or the end of a paperclip to press a button. Result: The AP reboots, and the factory default network values are restored. 2. If not using DHCP, use the ScanTool or CLI over a serial connection to set the IP address, subnet mask, and other IP parameters. See Using the Command Line Interface (CLI) for CLI information.

Figure 7-1

RELOAD and RESET Buttons

Forced Reload Procedure

Use this procedure to erase the current AP Image and download a new AP Image. In some cases, specifically when a missing or corrupted AP Image prevents successful booting, you may need to use ScanTool or the Bootloader CLI to download a new executable AP Image.

NOTE
This does not delete the APs configuration (in other words, the Forced Reload Procedure does not reset to device to factory defaults). If you need to force the AP to the factory default state after loading a new AP image, use the Reset to Factory Default Procedure above.

126

Troubleshooting the AP-2000

For this procedure, you will first erase the AP Image currently installed on the unit and then use either ScanTool or the Bootloader CLI (over the serial port) to set the IP address and download a new AP Image. Follow these steps: 1. While the unit is running, press the RESET button.

NOTE
See RELOAD and RESET Buttons to identify the buttons. You need to use a pin or the end of a paperclip to press a button. Result: The AP reboots and the indicators begin to flash.

CAUTION
By completing Step 2, the firmware in the AP will be erased. You will need an Ethernet connection, a TFTP server, and a serial cable (if using the Bootloader CLI) to reload firmware.

2. Press and hold the RELOAD button for about 20 seconds until the POWER LED turns amber. Result: The AP deletes the current AP Image. 3. Follow one of the procedures below to load a new AP Image to the Access Point: Download a New Image Using ScanTool Download a New Image Using the Bootloader CLI

Download a New Image Using ScanTool

To download the AP Image, you will need an Ethernet connection to the computer on which the TFTP server resides and to a computer that is running ScanTool (this is either two separate computers connected to the same network or a single computer running both programs). ScanTool detects if an Access Point does not have a valid software image installed. In this case, the TFTP Server and Image File Name parameters are enabled in the ScanTools Change screen so you can download a new image to the unit. (These fields are grayed out if ScanTool does not detect a software image problem.)

Preparing to Download the AP Image

Before starting, you need to know the Access Points IP address, subnet mask, the TFTP Server IP Address, and the AP Image file name. Make sure the TFTP server is running and configured to point to the folder containing the image to be downloaded.

Download Procedure
Follow these steps to use ScanTool to download a software image to an Access Point with a missing image: 1. 2. 3. 4. 5. Download the latest software from http://www.proxim.com. Copy the latest software updates to your TFTP server. Launch ScanTool. Highlight the entry for the AP you want to update and click Change. Set IP Address Type to Static.

NOTE
You need to assign static IP information temporarily to the Access Point since its DHCP client functionality is not available when no image is installed on the device. 6. Enter an unused IP address that is valid on your network in the IP Address field. You may need to contact your network administrator to get this address. 7. Enter the networks Subnet Mask in the field provided. 8. Enter the networks Gateway IP Address, if necessary. You may need to contact your network administrator to get this address. You should only need to enter the default gateway address if the Access Point and the TFTP server are separated by a router. 9. Enter the IP address of your TFTP server in the field provided. 10. Enter the Image File Name (including the file extension). Enter the full directory path and file name. If the file is located in the default TFTP directory, you need enter only the file name.

127

Troubleshooting the AP-2000

11. Click OK. Result: The Access Point will reboot and the download will begin automatically. You should see downloading activity begin after a few seconds within the TFTP servers status screen. 12. Click OK when prompted that the device has been updated successfully to return to the Scan List screen. 13. Click Cancel to close the ScanTool. 14. When the download process is complete, configure the AP as described in Getting Started and Performing Advanced Configuration.

Download a New Image Using the Bootloader CLI

To download the AP Image, you will need an Ethernet connection to the computer on which the TFTP server resides. This can be any computer on the LAN or connected to the AP with a cross-over Ethernet cable. You must also connect the AP to a computer with a standard serial cable and use a terminal client, such as HyperTerminal. From the terminal, enter CLI Commands to set the IP address and download an AP Image.

Preparing to Download the AP Image

Before starting, you need to know the Access Points IP address, subnet mask, the TFTP Server IP Address, and the AP Image file name. Make sure the TFTP server is running and configured to point to the folder containing the image to be downloaded.

Download Procedure
1. Download the latest software from http://www.proxim.com. 2. Copy the latest software updates to your TFTP servers default directory. 3. Use a straight-through serial cable to connect the Access Points serial port to your computers serial port.

NOTE
You must remove the Access Points cable cover and front cover to access the serial port. 4. Open your terminal emulation program (like HyperTerminal) and set the following connection properties: Com Port: <COM1, COM2, etc., depending on your computer> Baud rate: 9600 Data Bits: 8 Stop bits: 1 Flow Control: None Parity: None 5. Under File -> Properties -> Settings -> ASCII Setup, enable the Send line ends with line feeds option. Result: HyperTerminal sends a line return at the end of each line of code. 6. Press the RESET button on the AP. Result: The terminal display shows Power On Self Tests (POST) activity. After approximately 30 seconds, a message indicates: Sending Traps to SNMP manager periodically. After this message appears, press the ENTER key repeatedly until the following prompt appears: [Device name]>

128

Troubleshooting the AP-2000

7. Enter only the following statements: [Device name]> set ipaddrtype static [Device name]> set ipaddr <Access Point IP Address> [Device name]> set ipsubmask <IP Mask> [Device name]> set tftpipaddr <TFTP Server IP Address> [Device name]> set tftpfilename <AP Image File Name, including file extension> [Device name]> set ipgw <Gateway IP Address> [Device name]> show ip (to confirm your new settings) [Device name]> show tftp (to confirm your new settings) [Device name]> reboot 0 Example: [Device name]> set ipaddrtype static [Device name]> set ipaddr 10.0.0.12 [Device name]> set ipsubmask 255.255.255.0 [Device name]> set tftpipaddr 10.0.0.20 [Device name]> set tftpfilename MyImage.bin [Device name]> set ipgw 10.0.0.30 [Device name]> show ip [Device name]> show tftp [Device name]> reboot 0 Result: The AP will reboot and then download the image file. You should see downloading activity begin after a few seconds within the TFTP servers status screen. 8. When the download process is complete, configure the AP as described in Getting Started and Performing Advanced Configuration.

Setting IP Address using Serial Port

Use the following procedure to set an IP address over the serial port using the CLI. The network administrator typically provides the AP IP address.

Hardware and Software Requirements

Standard straight-through serial data (RS-232) cable with a one male DB-9 connector and one female DB-9 connector. The AP comes with a female 9-pin serial port. ASCII Terminal software, such as HyperTerminal.

Attaching the Serial Port Cable

1. 2. 3. 4. Unlock and remove the cable cover from the AP. Remove the front cover from the AP to reveal the serial port. Connect one end of the serial cable to the AP and the other end to a serial port on your computer. Power on the computer and AP, if necessary.

Initializing the IP Address using CLI

After installing the serial port cable, you may use the CLI to communicate with the AP. CLI supports most generic terminal emulation programs, such as HyperTerminal (which is included with the Windows operating systems). In addition, many web sites offer shareware or commercial terminal programs you can download. Once the IP address has been assigned, you can use the HTTP interface or the CLI over Telnet to complete configuration.

129

Troubleshooting the AP-2000

Follow these steps to assign the AP an IP address: 1. Open your terminal emulation program (like HyperTerminal) and set the following connection properties: Com Port: <COM1, COM2, etc., depending on your computer> Baud rate: 9600 Data Bits: 8 Stop bits: 1 Flow Control: None Parity: None 2. Under File -> Properties -> Settings -> ASCII Setup, enable the Send line ends with line feeds option. Result: HyperTerminal sends a line return at the end of each line of code. 3. Press the RESET button on the AP (see RELOAD and RESET Buttons to identify the location of the RESET button). Result: The terminal display shows Power On Self Tests (POST) activity, and then displays a CLI prompt, similar to the example below. This process may take up to 90 seconds. [Device name]> Please enter password: 4. Enter the CLI password (default is public). Result: The terminal displays a welcome message and then the CLI Prompt: [Device name]> 5. Enter show ip. Result: Network parameters appear:

Figure 7-2

Result of show ip CLI Command

6. Change the IP address and other network values using set and reboot CLI commands, similar to the example below (use your own IP address and subnet mask). Note that IP Address Type is set to Dynamic by default. If you have a DHCP server on your network, you should not need to manually configure the Access Points IP address; the Access Point will obtain an IP address from the networks DHCP server during boot-up. Result: After each entry the CLI reminds you to reboot; however wait to reboot until all commands have been entered. [Device name]> set ipaddrtype static [Device name]> set ipaddr <IP Address> [Device name]> set ipsubmask <IP Subnet Mask> [Device name]> set ipgw <Default Gateway IP Address> [Device name]> show ip (to confirm your new settings) [Device name]> reboot 0 7. After the AP reboots, verify the new IP address by reconnecting to the CLI and enter a show ip command. Alternatively, you can ping the AP from a network computer to confirm that the new IP address has taken effect. 8. When the proper IP address is set, use the HTTP interface or CLI over Telnet to configure the rest of the units operating parameters.

130

Troubleshooting the AP-2000

Related Applications
RADIUS Authentication Server
If you enabled RADIUS Authentication on the AP, make sure that your networks RADIUS servers are operational. Otherwise, clients will not be able to log in. There are several reasons the authentication server services might be unavailable, here are two typical things to check: Make sure you have the proper RADIUS authentication server information setup configured in the AP. Check the RADIUS Authentication Servers Shared Secret and Destination Port number (default is 1812; for RADIUS Accounting, the default is 1813). Make sure the RADIUS authentication server RAS setup matches the AP.

TFTP Server
The Trivial File Transfer Protocol (TFTP) server allows you to transfer files across a network. You can upload configuration files from the AP for backup or copying, and you can download configuration files or new software images. The TFTP software is located on the ORiNOCO AP Installation CD-ROM. If a TFTP server is not configured and running, you will not be able to download and upload images and configuration files to/from the AP. Remember that the TFTP server does not have to be local, so long as you have a valid TFTP IP address. Note that you do not need a TFTP server running unless you want to transfer files to or from the AP. After the TFTP server is installed: Check to see that TFTP is configured to point to the directory containing the AP Image. Make sure you have the proper TFTP server IP Address, the proper AP Image file name, and that the TFTP server is connected. Make sure the TFTP server is configured to both send and receive, with no time-out.

131

Using the Command Line Interface (CLI)

This section describes the APs Command Line (CLI) Interface. CLI commands can be used to initialize, configure, and manage the Access Point. CLI commands may be entered in real time through a keyboard or submitted with CLI scripts. A CLI Batch file is a user-editable configuration file that provides a user-friendly way to change the AP configuration through a file upload. The CLI Batch file is an ASCII file that facilitates Auto Configuration because it does not require the user to access one of the APs management interfaces to make configuration changes as is required with the proprietary TLV format configuration file. The CLI is available through both the Serial Port interface and over the Ethernet interface using Telnet.

NOTE
All CLI commands and parameters are case-sensitive. General Notes Command Line Interface (CLI) Variations CLI Command Types Using Tables & User Strings Configuring the AP using CLI commands Set Basic Configuration Parameters using CLI Commands Other Network Settings CLI Monitoring Parameters Parameter Tables CLI Batch File

General Notes
Prerequisite Skills and Knowledge
To use this document effectively, you should have a working knowledge of Local Area Networking (LAN) concepts, network access infrastructures, and client-server relationships. In addition, you should be familiar with software setup procedures for typical network operating systems and servers.

Notation Conventions
Computer prompts are shown as constant width type. For example: [Device-Name]> Information that you input as shown is displayed in bold constant width type. For example: [Device name]> set ipaddr 10.0.0.12 The names of keyboard keys, software buttons, and field names are displayed in bold type. For example: Click the Configure button. Screen names are displayed in bold italics. For example, the System Status screen.

Important Terminology
Configuration Files - Database files containing the current Access Point configuration. Configuration items include the IP Address and other network-specific values. Config files may be downloaded to the Access Point or uploaded for backup or troubleshooting.

132

Using the Command Line Interface (CLI)

Download vs. Upload - Downloads transfer files to the Access Point. Uploads transfer files from the Access Point. The TFTP server performs file transfers in both directions. Group - A logical collection of network parameter information. For example, the System Group is composed of several related parameters. Groups can also contain Tables. All items for a given Group can be displayed with a show <Group> CLI Command. Image File - The Access Point software executed from RAM. To update an Access Point you typically download a new Image File. This file is often referred to as the AP Image. Parameter - A fundamental network value that can be displayed and may be changeable. For example, the Access Point must have a unique IP Address and the Wireless interface must be assigned an SSID. Change parameters with the CLI set Command, and view them with the CLI show Command. Table - Tables hold parameters for several related items. For example, you can add several potential managers to the SNMP Table. All items for a given Table can be displayed with a show <Table> CLI Command. TFTP - Refers to the TFTP Server, used for file transfers.

Navigation and Special Keys

This CLI supports the following navigation and special key functions to move the cursor along the prompt line.
Key Combination Delete or Backspace Ctrl-A Ctrl-E Ctrl-F Ctrl-B Ctrl-D Ctrl-U Ctrl-P Ctrl-N Tab ? Operation Delete previous character Move cursor to beginning of line Move cursor to end of line Move cursor forward one character Move cursor back one character Delete the character the cursor is on Delete all text to left of cursor Go to the previous line in the history buffer Go to the next line in the history buffer Complete the command line List available commands

CLI Error Messages

The following table describes the error messages associated with improper inputs or expected CLI behavior.
Error Message Syntax Error Invalid Command Invalid Parameter Name Invalid Parameter Value Invalid Table Index Invalid Table Parameter Invalid Table Parameter Value Read Only Parameter Incorrect Password Download Unsuccessful Upload Unsuccessful Description Invalid syntax entered at the command prompt. A non-existent command has been entered at the command prompt. An invalid parameter name has been entered at the command prompt. An invalid parameter value has been entered at the command prompt. An invalid table index has been entered at the command prompt. An invalid table parameter has been entered at the command prompt. An invalid table parameter value has been entered at the command prompt. User is attempting to configure a read-only parameter. An incorrect password has been entered in the CLI login prompt. The download operation has failed due to incorrect TFTP server IP Address or file name. The upload operation has failed due to incorrect TFTP server IP Address or file name.

Command Line Interface (CLI) Variations

Administrators use the CLI to control Access Point operation and monitor network statistics. The AP supports two types of CLI: the Bootloader CLI and the normal CLI. The Bootloader CLI provides a limited command set, and is used when the current AP Image is bad or missing. The Bootloader CLI allows you to assign an IP Address and download a new image. Once the image is downloaded and running, the Access Point uses the normal CLI. This guide covers the normal CLI unless otherwise specified.

133

Using the Command Line Interface (CLI) Bootloader CLI

The Bootloader CLI is a minimal subset of the normal CLI used to perform initial configuration of the AP. This interface is only accessible via the serial interface if the AP does not contain a software image or a download image command over TFTP has failed. The Bootloader CLI provides you with the ability to configure the initial setup parameters as well as download a software image to the device. The following functions are supported by the Bootloader CLI: configuration of initial device parameters using the set command show command to view the devices configuration parameters help command to provide additional information on all commands supported by the Bootloader CLI reboot command to reboot the device System Name IP Address Assignment Type IP Address IP Mask Gateway IP Address TFTP Server IP Address Image File Name (including the file extension)

The parameters supported by the Bootloader CLI (for viewing and modifying) are:

The following lists display the results of using the help command in the Bootloader CLI:

Figure A-1

Results of help bootloader CLI command

The following lists display the results of using the show command in the Bootloader CLI:

Figure A-2

Results of show bootloader CLI command

134

Using the Command Line Interface (CLI)

CLI Command Types

This guide divides CLI Commands into two categories: Operational and Parameter Controls.

Operational CLI Commands

These commands affect Access Point behavior, such as downloading, rebooting, and so on. After entering commands (and parameters, if any) press the Enter key to execute the Command Line. Operational commands include: ?: Typing a question mark lists CLI Commands or parameters, depending on usage (you do not need to type Enter after typing this command) done, exit, quit: Terminates the CLI session download: Uses a TFTP server to download image files, config files, bootloader upgrade files, SSL certificates, SSL private keys, SSH public keys, SSH private keys, or CLI Batch Files to the Access Point help: Displays general CLI help information or command help information, such as command usage and syntax history: Remembers commands to help avoid re-entering complex statements passwd: Sets the Access Points CLI password reboot: Reboots the Access Point in the specified time search: Lists the parameters in a specified Table upload: Uses TFTP server to upload config files from Access Point to TFTP default directory or specified path

? (List Commands)
This command can be used in a number of ways to display available commands and parameters. The following table lists each operation and provides a basic example. Following the table are detailed examples and display results for each operation.
Operation Display the Command List (Example 1) Display commands that start with specified letters (Example 2) Display parameters for set and show Commands (Examples 3a and 3b) Prompt to enter successive parameters for Commands (Example 4) Basic Example

[Device-Name]>? [Device-Name]>s? [Device-Name]>set ? [Device-Name]>show ipa? [Device-Name]>download ?

Example 1. Display Command list

To display the Command List, enter ?. [Device-Name]>?

Figure A-3

Result of ? CLI command

Example 2. Display specific Commands

To show all commands that start with specified letters, enter one or more letters, then ? with no space between letters and ?. [Device-Name]>s?

135

Using the Command Line Interface (CLI)

Figure A-4

Result of s? CLI command

Example 3. Display parameters for set and show

Example 3a allows you to see every possible parameter for the set (or show) commands. Notice from example 3a that the list is very long. Example 3b shows how to display a subset of the parameters based on initial parameter letters.

Example 3a. Display every parameter that can be changed

[Device-Name]>set ?

. . . .

Figure A-5

Result of set ? CLI command

Example 3b. Display parameters based on letter sequence

This example shows entries for parameters that start with the letter i. The more letters you enter, the fewer the results returned. Notice that there is no space between the letters and the question mark. [Device-Name]> show ipa?

Figure A-6

Result of show ipa? CLI command

[Device-Name]> show iparp?

Figure A-7

Result of show iparp? CLI command

136

Using the Command Line Interface (CLI)

Example 4. Display Prompts for Successive Parameters
Enter the command, a space, and then ?. Then, when the parameter prompt appears, enter the parameter value. Result: The parameter is changed and a new CLI line is echoed with the new value (in the first part of the following example, the value is the IP Address of the TFTP server). After entering one parameter, you may add another ? to the new CLI line to see the next parameter prompt, and so on until you have entered all of the required parameters. The following example shows how this is used for the download Command. The last part of the example shows the completed download Command ready for execution. [Device-Name]> download ? <TFTP IP Address> [Device-Name]> download 192.168.0.101 ? <File Name> [Device-Name]> download 192.168.0.101 apimage ? <file type (config/img/bootloader)> [Device-Name]> download 192.168.0.101 apimage img <CR>

done, exit, quit

Each of the following commands ends a CLI session: [Device-Name]> done [Device-Name]> exit [Device-Name]> quit

download
Downloads the specified file from a TFTP server to the Access Point. Executing download in combination with the asterisks character (*) will make use of the previously set TFTP parameters. Executing download without parameters will display command help and usage information. 1. Syntax to download a file: Device-Name]>download <tftp server address> <path and filename> <file type> Example: [Device-Name]>download 192.168.1.100 APImage2 img 2. Syntax to display help and usage information: [Device-Name]>download 3. Syntax to execute the download Command using previously set (stored) TFTP Parameters: [Device-Name]>download *

help
Displays instructions on using control-key sequences for navigating a Command Line and displays command information and examples. 1. Using help as the only argument: [Device-Name]>help

137

Using the Command Line Interface (CLI)

Figure A-8

Results of help CLI command

2. Complete command description and command usage can be provided by: [Device-Name]>help <command name> [Device-Name]><command name> help

history
Shows content of Command History Buffer. The Command History Buffer stores command statements entered in the current session. To avoid re-entering long command statements, use the keyboard up arrow (Ctrl-P) and down arrow (Ctrl-N) keys to recall previous statements from the Command History Buffer. When the desired statement reappears, press the Enter key to execute, or you may edit the statement before executing it. [Device-Name]> history

passwd
Changes the CLI Password. [Device-Name]> passwd oldpassword newpassword newpassword

reboot
Reboots Access Point after specified number of seconds. Specify a value of 0 (zero) for immediate reboot. [Device-Name]> reboot 0 [Device-Name]> reboot 30

search
Lists the parameters supported by the specified table. This list corresponds to the table information displayed in the HTTP interface. In this example, the CLI returns the list of parameters that make up an entry in the IP Access Table. [Device-Name]> search mgmtipaccesstbl

Figure A-9

Results of search mgmtipaccesstbl CLI command

138

Using the Command Line Interface (CLI)

upload
Uploads a text-based configuration file from the AP to the TFTP Server. Executing upload with the asterisk character (*) will make use of the previously set/stored TFTP parameters. Executing upload without parameters will display command help and usage information. 1. Syntax to upload a file: [Device-Name]>upload <tftp server address> <path and filename> <filetype> Example: [Device-Name]>upload 192.168.1.100 APconfig.sys config 2. Syntax to display help and usage information: [Device-Name]>help upload 3. Syntax to execute the upload command using previously set (stored) TFTP Parameters: [Device-Name]>upload *

Parameter Control Commands

The following sections cover the two Parameter Control Commands (show and set) and include several tables showing parameter properties. These commands allow you to view (show) all parameters and statistics and to change (set) parameters. show: To see any Parameter or Statistic value, you can specify a single parameter, a Group, or a Table. set: Use this CLI Command to change parameter values. You can use a single CLI statement to modify Tables, or you can modify each parameter separately.

show CLI Command

Displays the value of the specified parameter, or displays all parameter values of a specified group (parameter table). Groups contain Parameters and Tables. Tables contain parameters for a series of similar entities. To see a definition and syntax example, type only show and then press the Enter key. To see a list of available parameters, enter a question mark (?) after show (example: show ?). Syntax: [Device-Name]>show <parameter> [Device-Name]>show <group> [Device-Name]>show <table> Examples: [Device-Name]>show ipaddr [Device-Name]>show network [Device-Name]>show mgmtipaccesstbl

set CLI Command

Sets (modifies) the value of the specified parameter. To see a definition and syntax example, type only set and then press the Enter key. To see a list of available parameters, enter a space, then a question mark (?) after set (example: set?). Syntax: [Device-Name]>set <parameter> <value> [Device-Name]>set <table> <index> <argument 1> <value 1> ... <argument N> <value N> Example: [Device-Name]>set sysloc Main Lobby [Device-Name]>set mgmtipaccesstbl 0 ipaddr 10.0.0.10 ipmask 255.255.0.0

139

Using the Command Line Interface (CLI)

Configuring Objects that Require Reboot
Certain objects supported by the Access Point require a device reboot in order for the changes to take effect. In order to inform the end-user of this behavior, the CLI provides informational messages when the user has configured an object that requires a reboot. The following messages are displayed as a result of the configuring such object or objects.

Example 1: Configuring objects that require the device to be rebooted

The following message is displayed every time the user has configured an object that requires the device to be rebooted. [Device-Name]>set ipaddr 135.114.73.10
The following elements require reboot ipaddr

Example 2: Executing the exit, quit, or done commands when an object that requires reboot has been configured
In addition to the above informational message, the CLI also provides a message as a result of the exit, quit, or done command if changes have been made to objects that require reboot. If you make changes to objects that require reboot and execute the exit command the following message is displayed: [Device-Name]>exit<CR> OR quit<CR> OR done<CR>
Modifications have been made to parameters that require the device to be rebooted. These changes will only take effect after the next reboot.

set and show Command Examples

In general, you will use the CLI show Command to view current parameter values and use the CLI set Command to change parameter values. As shown in the following examples, parameters may be set individually or all parameters for a given table can be set with a single statement.

Example 1 - Set the Access Point IP Address Parameter

Syntax: [Device-Name]>set <parameter name> <parameter value> Example: [Device-Name]> set ipaddr 10.0.0.12 Result: IP Address will be changed when you reboot the Access Point. The CLI reminds you when rebooting is required for a change to take effect. To reboot immediately, enter reboot 0 (zero) at the CLI prompt.

Example 2 - Create a table entry or row

Use 0 (zero) as the index to a table when creating an entry. When creating a table row, only the mandatory table elements are required (comment is usually an optional table element). For optional table elements, the default value is generally applied if you do not specify a value. Syntax: [Device-Name]>set <table name> <table index> <element 1> <value 1> <element n> <value n> Example: [Device-Name]> set mgmtipaccesstbl 0 ipaddr 10.0.0.10 ipmask 255.255.0.0 Result: A new table entry is created for IP address 10.0.0.10 with a 255.255.0.0 subnet mask.

140

Using the Command Line Interface (CLI)

Example 3 - Modify a table entry or row
Use the index to be modified and the table elements you would like to modify. For example, suppose the IP Access Table has one entry and you wanted to modify the IP address: [Device-Name]>set mgmtipaccesstbl 1 ipaddr 10.0.0.11 You can also modify several elements in the table entry. Enter the index number and specific table elements you would like to modify. (Hint: Use the search Command to see the elements that belong to the table.) [Device-Name]>set mgmtipaccesstbl 1 ipaddr 10.0.0.12 ipmask 255.255.255.248 cmt First Row

Example 4 - Enable, Disable, or Delete a table entry or row

The following example illustrates how to manage the second entry in a table. Syntax: [Device-Name]>set <Table> index status <enable, disable, delete> [Device-Name]>set <Table> index status <1=enable, 2=disable, 3=delete> Example: [Device-Name]>set [Device-Name]>set [Device-Name]>set [Device-Name]>set

mgmtipaccesstbl mgmtipaccesstbl mgmtipaccesstbl mgmtipaccesstbl

2 2 2 2

status status status status

enable disable delete 2

NOTE
You may need to enable a disabled table entry before you can change the entrys elements.

Example 5 - Show the Group Parameters

This example illustrates how to view all elements of a group or table. Syntax: [Device-Name]> show <group name> Example: [Device-Name]>show network Result: The CLI displays network group parameters. Note show network and show ip return the same data.

Figure A-10 Results of show network and show ip CLI Commands

141

Using the Command Line Interface (CLI)

Example 6 - Show Individual and Table Parameters
1. View a single parameter. Syntax: [Device-Name]>show <parameter name> Example: [Device-Name]> show ipaddr Result: Displays the Access Point IP address.

Figure A-11 Result of show ipaddr CLI Command 2. View all parameters in a table. Syntax: [Device-Name]> show <table name> Example:[Device-Name]> show mgmtipaccesstbl Result: Displays the IP Access Table and its entries.

Using Tables & User Strings

Working with Tables
Each table element (or parameter) must be specified, as in the example below. [Device-Name]>set mgmtipaccesstbl 0 ipaddr 10.0.0.10 ipmask 255.255.0.0 Below are the rules for creating, modifying, enabling/disabling, and deleting table entries. Creation The table name is required. The table index is required for table entry/instance creation the index is always zero (0). The order in which the table arguments or objects are entered in not important. Parameters that are not required can be omitted, in which case they will be assigned the default value. Modification The table name is required. The table index is required to modify the table, index must be the index of the entry to be modified. Only the table objects that are to be modified need to be specified. Not all the table objects are required. If multiple table objects are to be modified the order in which they are entered is not important. If the entire table entry is to be modified, all the table objects have to be specified. Enabling/Disabling The table name is required. The table index is required for table enabling/disabling the index should be the index of the entry to be enabled/disabled. The entrys new state (either enable or disable) is required. Deletion The table name is required. The table index is required for table deletion the index should be the index of the entry to be deleted. The word delete is required.

142

Using the Command Line Interface (CLI) Using Strings

Since there are several string objects supported by the AP, a string delimiter is required for the strings to be interpreted correctly by the command line parser. For this CLI implementation, the single quote or double quote character can be used at the beginning and at the end of the string. For example: [Device-Name]> set sysname Lobby - Does not need quote marks [Device-Name]> set sysname Front Lobby - Requires quote marks. The scenarios supported by this CLI are:
My Desk in the office My Desk in the office My Desk in the office My Desk in the office Daniels Desk in the office Daniels Desk in the office Double Quotes Single Quotes Single Quotes within Double Quotes Double Quotes within Single Quotes One Single Quote within Double Quotes One Double Quote within Single Quotes

The string delimiter does not have to be used for every string object. The single quote or double quote only has to be used for string objects that contain blank space characters. If the string object being used does not contain blank spaces, then the string delimiters, single or double quotes, mentioned in this section are not required.

Configuring the AP using CLI commands

Log into the AP using HyperTerminal
1. Open your terminal emulation program (like HyperTerminal) and set the following connection properties: Com Port: <COM1, COM2, etc., depending on your computer> Baud rate: 9600 Data Bits: 8 Stop bits: 1 Flow Control: None Parity: None Under File -> Properties -> Settings -> ASCII Setup, enable the Send line ends with line feeds option. Result: HyperTerminal sends a line return at the end of each line of code. Enter the CLI password (default is public).

2. 3.

NOTE
Proxim recommends changing your default passwords immediately. To perform this operation using CLI commands, refer to Change Passwords.

Log into the AP using Telnet

The CLI commands can be used to access, configure, and manage the AP using Telnet. Follow these steps: 1. Confirm that your computers IP address is in the same IP subnet as the AP.

NOTE
If you have not previously configured the Access Points IP address and do not have a DHCP server on the network, the Access Point will default to an IP address of 10.0.0.1. 2. 3. 4. Go to the DOS command prompt on your computer. Type telnet <IP Address of the unit>. Enter the CLI password (default is public).

143

Using the Command Line Interface (CLI)

NOTE
Proxim recommends changing your default passwords immediately. To perform this operation using CLI commands, refer to Change Passwords.

Set Basic Configuration Parameters using CLI Commands

There are a few basic configuration parameters that you may want to setup right away when you receive the AP. For example: Set System Name, Location and Contact Information Set Static IP Address for the AP Download an AP Configuration File from your TFTP Server Set up Auto Configuration Set Network Names for the Wireless Interface Enable and Configure TX Power Control for the Wireless Interface(s) Configure SSID (Network Name) and VLAN Pairs, and Profiles Download an AP Configuration File from your TFTP Server Backup your AP Configuration File

Set System Name, Location and Contact Information

[Device-Name]>set sysname <system name> sysloc <Unit Location> [Device-Name]>set sysctname <Contact Name (person responsible for system)> [Device-Name]>set sysctphone <Contact Phone Number> sysctemail <Contact E-mail address> [Device-Name]>show system

Figure A-12 Result of show system CLI Command

Set Static IP Address for the AP

NOTE
The IP Subnet Mask of the AP must match your networks Subnet Mask. [Device-Name]>set ipaddrtype static [Device-Name]>set ipaddr <fixed IP address of unit> [Device-Name]>set ipsubmask <IP Mask> [Device-Name]>set ipgw <gateway IP address> [Device-Name]>show network

Change Passwords
[Device-Name]>passwd <Old Password> <New Password> <Confirm Password> (CLI password) [Device-Name]>set httppasswd <New Password> (HTTP interface password) [Device-Name]>set snmprpasswd <New Password> (SNMP read password) [Device-Name]>set snmprwpasswd <New Password> (SNMP read/write) [Device-Name]>set snmpv3authpasswd <New Password> (SNMPv3 authentication password)

144

Using the Command Line Interface (CLI)

[Device-Name]>set snmpv3privpasswd <New Password> (SNMPv3 privacy password) [Device-Name]>reboot 0

CAUTION
Proxim strongly urges you to change the default passwords to restrict access to your network devices to authorized personnel. If you lose or forget your password settings, you can always perform the Reset to Factory Default Procedure.

Set Network Names for the Wireless Interface

[Device-Name]>set wif <index 3 (Slot A) or 4 (Slot B)> netname <Network Name (SSID) for wireless interface> [Device-Name]>show wif

Figure A-13 Results of show wif CLI command for an AP

Enable and Configure TX Power Control for the Wireless Interface(s)

The TX Power Control feature lets the user configure the transmit power level of the card in the AP at one of four levels: 100% of the maximum transmit power level of the card 50% 25% 12.5%

Perform the following commands to enable TX Power Control and set the transmit power level: [Device-Name]>set txpowercontrol enable [Device-Name]>set wif <interface number> currenttxpowerlevel <value> Allowed values are: 1 (100%), 2 (50%), 3 (25%), 4 (12.5%)

Configure SSID (Network Name) and VLAN Pairs, and Profiles

Perform the following command to configure an SSID/VLAN pair, and to assign a Security Profile and RADIUS Profiles to it. [Device-Name]>set wifssidtbl <Index.subindex> ssid <Network Name> vlanid <-1 to 1094> ssidauth <enable/disable> acctstatus <enable/disable> secprofile <Security Profile Nmuber> radmacprofile <MAC Authentication Profile Name> radeapprofile <EAP Authentication Profile Name> radacctprofile <Accounting Profile Name> radmacauthstatus <enable/disable> aclstatus <enable/disable> denynonencrypted <enable/disable>

145

Using the Command Line Interface (CLI)

Examples: [Device-Name]>set wifssidtbl 3.1 ssid accesspt1 vlanid 22 ssidauth enable acctstatus enable secprofile 1 radmacprofile "MAC Authentication" radeapprofile "EAP Authentication" radacctprofile "Accounting" radmacauthstatus enable aclstatus enable set wifssidtbl 4.1 ssid accesspt1 vlanid 22 ssidauth enable acctstatus enable secprofile 1 radmacprofile "MAC Authentication" radeapprofile "EAP Authentication" radacctprofile "Accounting" radmacauthstatus enable aclstatus enable

146

Using the Command Line Interface (CLI)

Download an AP Configuration File from your TFTP Server
Begin by starting your TFTP program. It must be running and configured to transmit and receive. [Device-Name]>set tftpfilename <file name> tftpfiletype config tftpipaddr <IP address of your TFTP server> [Device-Name]>show tftp (to ensure the filename, file type, and the IP address are correct) [Device-Name]>download * [Device-Name]>reboot 0 After following the complete process (above) once, you can download a file of the same name (so long as all the other parameters are the same), with the following command: [Device-Name]>download *

Backup your AP Configuration File

Begin by starting your TFTP program. It must be running and configured to transmit and receive. [Device-Name]>upload <TFTP Server IP address> <tftpfilename (such as config.sys)> config [Device-Name]>show tftp (to ensure the filename, file type, and the IP address are correct) After setting the TFTP parameters, you can backup your current file (so long as all the other parameters are the same), with the following command: [Device-Name]>upload *

Set up Auto Configuration

The Auto Configuration feature which allows an AP to be automatically configured by downloading a specific configuration file from a TFTP server during the boot up process. Perform the following commands to enable and set up automatic configuration:

NOTE
The configuration filename and TFTP server IP address are configured only when the AP is configured for Static IP. If the AP is configured for Dynamic IP these parameters are not used and obtained from DHCP. The default filename is config. The default TFTP IP address is 10.0.0.2 for AP-2000. [Device-Name]>set autoconfigstatus <enable/disable> [Device-Name]>set autoconfigfilename <filename> Enter the filename of the configuration file that is used if the AP is configured for Static IP. [Device-Name]>set autoconfigTFTPaddr <IP address> Enter the TFTP server address that is used if the AP is configured for Static IP.

Other Network Settings

There are other configuration settings that you may want to set for the AP. Some of them are listed below. Configure the AP as a DHCP Server Configure the DNS Client Maintain Client Connections using Link Integrity Change your Wireless Interface Settings Set Ethernet Speed and Transmission Mode Set Interface Management Services Configure MAC Access Control Set RADIUS Parameters Set Rogue Access Point Detection (RAD) Parameters Set VLAN/SSID Parameters

147

Using the Command Line Interface (CLI)

NOTE
Refer to Performing Advanced Configuration for more information on these settings.

Configure the AP as a DHCP Server

NOTE
You must have at least one entry in the DHCP Server IP Address Pool Table before you can set the DHCP Server Status to Enable. [Device-Name]>set dhcpstatus disable [Device-Name]>set dhcpippooltbl 0 startipaddr <start ip address> endipaddr <end ip address> [Device-Name]>set dhcpgw <gateway ip address> [Device-Name]>set dhcppridnsipaddr <primary dns ip address> [Device-Name]>set dhcpsecdnsipaddr <secondary dns ip address> [Device-Name]>set dhcpstatus enable [Device-Name]>reboot 0

CAUTION
Before enabling this feature, confirm that the IP address pools you have configured are valid addresses on the network and do not overlap the addresses assigned by any other DHCP server on the network. Enabling this feature with incorrect address pools will cause problems on your network.

Configure the DNS Client

[Device-Name]>set dnsstatus enable [Device-Name]>set dnsprisvripaddr <IP address of primary DNS server> [Device-Name]>set dnssecsvripaddr <IP address of secondary DNS server> [Device-Name]>set dnsdomainname <default domain name> [Device-Name]>show dns

Figure A-14 Results of show dns CLI command

Maintain Client Connections using Link Integrity

[Device-Name]>show linkinttbl (this shows the current links) [Device-Name]>set linkinttbl <1-5 (depending on what table row you wish to address)> ipaddr <ip address of the host computer you want to check> [Device-Name]>set linkintpollint <the interval between link integrity checks> [Device-Name]>set linkintpollretx <number of times to retransmit before considering the link down> [Device-Name]>set linkintstatus enable [Device-Name]>show linkinttbl (confirm new settings) [Device-Name]>reboot 0

Change your Wireless Interface Settings

See Interfaces for information on the parameters listed below. Dual-radio APs use index 3 for Slot A and index 4 for Slot B.

148

Using the Command Line Interface (CLI)

Operational Mode
[Device-Name]>set wif <index> mode <see table>
mode 1 2 3 4 5 Operational Mode dot11b-only dot11g-only dot11bg dot11a-only dot11g-wifi

Autochannel Select (ACS)

ACS is enabled by default. Reboot after disabling or enabling ACS. [Device-Name]>set wif <index> autochannel <enable/disable> [Device-Name]>reboot 0

Enable/Disable Closed System

[Device-Name]>set wif <index> closedsys <enable/disable>

Shutdown/Resume Wireless Service

[Device-Name]>set wif <index> wssstatus <1 (resume)/2 (shutdown)>

Enable/Disable Interference Robustness (802.11b Only)

[Device-Name]>set wif <index> interrobust <enable/disable>

Enable/Disable Load Balancing (802.11b Only)

[Device-Name]>set wif <index> ldbalance <enable/disable>

Enable/Disable Medium Density Distribution (802.11b Only)

[Device-Name]>set wif <index> meddendistrib <enable/disable>

Set the Distance Between APs (802.11b Only)

[Device-Name]>set wif <index> distaps <large, medium, small, minicell, microcell> [Device-Name]>reboot 0

NOTE
The distance between APs should not be approximated. It is calculated by means of a manual Site Survey, in which an AP is set up and clients are tested throughout the area to determine signal strength and coverage, and local limits such as physical interference are investigated. From these measurements the appropriate cell size and density is determined, and the optimum distance between APs is calculated to suit your particular business requirements.

149

Using the Command Line Interface (CLI)

Set the Multicast Rate (802.11b Only)
[Device-Name]>set wif <index> multrate <1,2,5.5,11 (Mbits/sec)>

NOTE
The Distance Between APs must be set before the Multicast Rate.

Enable/Disable Super Mode (802.11a/g only)

[Device-Name]>set wif 3 super <enable/disable>

Enable/Disable Turbo Mode (802.11a/g only)

[Device-Name]>set wif 3 turbo <enable/disable>

NOTE
Super mode must be enabled on the interface before Turbo mode can be enabled.

Set Ethernet Speed and Transmission Mode

[Device-Name]>set etherspeed <value (see below)> [Device-Name]>reboot 0
Ethernet Speed and Transmission Mode 10 Mbits/sec - half duplex 10 Mbits/sec - full duplex 10 Mbits/sec - auto duplex 100 Mbits/sec - half duplex 100 Mbits/sec - full duplex Auto Speed - half duplex Auto Speed - auto duplex Value 10halfduplex 10fullduplex 10autoduplex 100halfduplex 100fullduplex autohalfduplex autoautoduplex (default)

Set Interface Management Services

Edit Management IP Access Table
[Device-Name]>set mgmtipaccesstbl <index> ipaddr <IP address> ipmask <subnet mask>

Configure Management Ports

[Device-Name]>set snmpifbitmask <(see below)> [Device-Name]>set httpifbitmask <(see below)> [Device-Name]>set telifbitmask <(see below)> Choose from the following values:
Interface bitmask 0 or 2 = disable (all interfaces) 1 or 3 = Ethernet only 4 or 6 = Wireless A only 8 or 10 = Wireless B only 12 = Wireless A and Wireless B 13 or 15 = all interfaces Description All management channels disabled Ethernet only enabled Wireless A only enabled Wireless B only enabled Wireless A and Wireless B enabled All management channels enabled

Set Communication Ports

[Device-Name]>set httpport <HTTP port number (default is 80)> [Device-Name]>set telport <Telnet port number (default is 23)>

150

Using the Command Line Interface (CLI)

Configure Secure Socket Layer (HTTPS)
Enabling SSL and configuring a passphrase allows encrypted Secure Socket Layer communications to the AP through the HTTPS interface. [Device-Name]>set sslstatus <enable/disable> The user must change the SSL passphrase when uploading a new certificate/private key pair, which will have a corresponding passphrase. [Device-Name]>set sslpassphrase <SSL certificate passphrase> [Device-Name]>show http To view all HTTP configuration information including SSL. HTTP Group Parameters ===================== httpifbitmask httppasswd httpport httphelplink httpsetupwiz sslstatus sslpassphrase : : : : : : : 15 ******** 80 file:///C:/Program Files/ORiNOCO/AP2000/HTML/home.htm disable enable ********

Set Telnet Session Timeouts

[Device-Name]>set tellogintout <time in seconds between 1 and 300 (default is 30)> [Device-Name]>set telsessiontout <time in seconds between 1 and 36000 (default is 900)>

Configure Serial Port Interface NOTE

To avoid unexpected performance issues, leave Flow Control at the default setting (none) unless you are sure what this setting should be. [Device-Name]>set serbaudrate <2400, 4800, 9600, 19200, 38400, 57600> [Device-Name]>set serflowctrl <none, xonxoff> [Device-Name]>show serial

Figure A-15 Result of show serial CLI Command

Configure Syslog
[Device-Name]>set [Device-Name]>set [Device-Name]>set [Device-Name]>set [Device-Name]>set <enable/disable> syslogpriority <1-7 (default is 6)> syslogstatus <enable/disable> sysloghbstatus <enable/disable> (default is disable) sysloghbinterval <1 - 604800> (default is 900 seconds) sysloghosttbl <index> ipaddr <ipaddress> cmt <comment> status

Configure Intra BSS

[Device-Name]>set intrabssoptype <passthru (default)/block)>

151

Using the Command Line Interface (CLI)

Configure MAC Access Control
Setup MAC (Address) Access Control
[Device-Name]>set macaclstatus enable [Device-Name]>set macacloptype <passthru, block> [Device-Name]>reboot 0

Add an Entry to the MAC Access Control Table

[Device-Name]>set macacltbl <index> macaddr <MAC Address> status enable [Device-Name]>show macacltbl

Disable or Delete an Entry in the MAC Access Control Table

[Device-Name]>set macacltbl <index> status <disable/delete> [Device-Name]>show macacltbl

NOTE
For larger networks that include multiple Access Points, you may prefer to maintain this list on a centralized location using the RADIUS parameters (see Set RADIUS Parameters).

152

Using the Command Line Interface (CLI)

Set RADIUS Parameters
Configure RADIUS Authentication servers
Perform the following command to configure a RADIUS Server and assign it to a VLAN. The RADIUS Server Profile index is specified by the index parameter and the subindex parameter specifies whether you are configuring a primary or secondary RADIUS server. [Device-Name]>set radiustbl <Index> profname <Profile Name> seraddrfmt <1 - IP Address 2 - Name> sernameorip <IP Address or Name> port <value> ssecret <value> responsetm <value> maxretx <value> acctupdtintrvl <value> macaddrfmt <value> authlifetm <value> radaccinactivetmr <value> vlanid <vlan id -1 to 4094> status enable

Examples of Configuring Primary and Secondary RADIUS Servers and Displaying the RADIUS Configuration
Primary server configuration: set radiustbl 1.1 profname "MAC Authentication" seraddrfmt 1 sernameorip 20.0.0.20 port 1812 ssecret public responsetm 3 maxretx 3 acctupdtintrvl 0 macaddrfmt 1 authlifetm 900 radaccinactivetmr 5 vlanid 22 status enable Secondary server configuration: set radiustbl 1.2 profname "MAC Authentication" seraddrfmt 1 sernameorip 20.0.0.30 port 1812 ssecret public responsetm 3 maxretx 3 acctupdtintrvl 0 macaddrfmt 1 authlifetm 900 radaccinactivetmr 5 vlanid 33 status enable [Device-Name]>show radiustbl Index Primary/Backup Profile Name Server Status Server Addressing Format IP Address/Host Name Destination Port VLAN Identifier MAC Address Format Response Time Maximum Retransmission Authorization Lifetime Accounting Update Interval Accounting Inactivity Timer Index Primary/Backup Profile Name Server Status Server Addressing Format IP Address/Host Name Destination Port VLAN Identifier MAC Address Format Response Time Maximum Retransmission Authorization Lifetime Accounting Update Interval Accounting Inactivity Timer : : : : : : : : : : : : : : : : : : : : : : : : : : : : 1 Primary MAC Authentication notReady ipaddr 0.0.0.0 1812 -1 dashdelimited 3 3 0 0 5 1 Backup MAC Authentication notReady ipaddr 0.0.0.0 1812 -1 dashdelimited 3 3 0 0 5

153

Using the Command Line Interface (CLI)

Index Primary/Backup Profile Name Server Status Server Addressing Format IP Address/Host Name Destination Port VLAN Identifier MAC Address Format Response Time Maximum Retransmission Authorization Lifetime Accounting Update Interval Accounting Inactivity Timer Index Primary/Backup Profile Name Server Status Server Addressing Format IP Address/Host Name Destination Port VLAN Identifier MAC Address Format Response Time Maximum Retransmission Authorization Lifetime Accounting Update Interval Accounting Inactivity Timer Index Primary/Backup Profile Name Server Status Server Addressing Format IP Address/Host Name Destination Port VLAN Identifier MAC Address Format Response Time Maximum Retransmission Authorization Lifetime Accounting Update Interval Accounting Inactivity Timer Index Primary/Backup Profile Name Server Status Server Addressing Format IP Address/Host Name Destination Port VLAN Identifier MAC Address Format Response Time Maximum Retransmission Authorization Lifetime : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 2 Primary EAP Authentication notReady ipaddr 0.0.0.0 0 -1 dashdelimited 3 3 0 0 5 2 Backup EAP Authentication notReady ipaddr 0.0.0.0 0 -1 dashdelimited 3 3 0 0 5 3 Primary Accounting notReady ipaddr 0.0.0.0 1813 -1 dashdelimited 3 3 0 0 5 3 Backup Accounting notReady ipaddr 0.0.0.0 1813 -1 dashdelimited 3 3 0

154

Using the Command Line Interface (CLI)

Accounting Update Interval Accounting Inactivity Timer Index Primary/Backup Profile Name Server Status Server Addressing Format IP Address/Host Name Destination Port VLAN Identifier MAC Address Format Response Time Maximum Retransmission Authorization Lifetime Accounting Update Interval Accounting Inactivity Timer Index Primary/Backup Profile Name Server Status Server Addressing Format IP Address/Host Name Destination Port VLAN Identifier MAC Address Format Response Time Maximum Retransmission Authorization Lifetime Accounting Update Interval Accounting Inactivity Timer : 0 : 5 : : : : : : : : : : : : : : : : : : : : : : : : : : : : 4 Primary Management Access notReady ipaddr 0.0.0.0 1812 -1 dashdelimited 3 3 0 0 5 4 Backup Management Access notReady ipaddr 0.0.0.0 1812 -1 dashdelimited 3 3 0 0 5

Set Rogue Access Point Detection (RAD) Parameters

The Rogue AP Detection (RAD) feature enables an additional security level for wireless LAN deployments. The RAD feature provides a mechanism for detecting Rogue Access Points by utilizing the coverage of the trusted Access Point deployment. The Rogue AP Scan employs background scanning using low-level 802.11 scanning functions for effective wireless detection of Access Points in its coverage area with minimal impact on the normal operation of the Access Point. The set radstatus command enables Rogue Access Point Detection. The scan repetition duration (radscanint) is also configurable.If the Access Point uses directional antennas to provide directional coverage, then the interface bitmask (radifbitmask) can be configured to maximize the scanning coverage area. [Device-Name]>set radstatus enable [Device-Name]>set radscanint <15-1440> [Device-Name]>set radifbitmask <4 (WiF A), 8 (WiF B), or 12 (both interfaces)> [Device-Name]>show rad

Figure A-16 Results of show rad CLI command

155

Using the Command Line Interface (CLI)

Set Hardware Configuration Reset Parameters
The Hardware Configuration Reset commands allows you to enable or disable the hardware reset functionality and to change the password to be used for configuration reset during boot up. To disable hardware configuration reset, enter: [Device-Name]>set hwconfigresetstatus disable To enable hardware configuration reset, enter: [Device-Name]>set hwconfigresetstatus enable To define the Configuration Reset Password to be used for configuration reset during boot up, enter the following command [Device-Name]>set configresetpasswd <password>] It is important to safely store the configuration reset password. If a user forgets the configuration reset password, the user will be unable to reset the AP to factory default configuration if the AP becomes inaccessible and the hardware configuration reset functionality is disable.

Set VLAN/SSID Parameters

Enable VLAN Management
[Device-Name]>set vlanstatus enable [Device-Name]>set vlanmgmtid <-1-4094> [Device-Name]>show wifssidtbl (to review your settings) [Device-Name]>reboot 0

Disable VLAN Management

[Device-Name]>set vlanstatus disable or 2 [Device-Name]>set vlanmgmtid 0 [Device-Name]>reboot 0

CLI Monitoring Parameters

Using the show command with the following table parameters will display operating statistics for the AP (these are the same statistics that are described in Monitoring the AP-2000 for the HTTP Web interface). staticmp: Displays the ICMP Statistics. statarptbl: Displays the IP ARP Table Statistics. statbridgetbl: Displays the Learn Table. statiapp: Displays the IAPP Statistics. statradius: Displays the RADIUS Authentication Statistics. statif: Displays information and statistics about the Ethernet and wireless interfaces. stat802.11: Displays additional statistics for the wireless interfaces. statethernet: Displays additional statistics for the Ethernet interface. statmss: Displays station statistics and Wireless Distribution System links.

Parameter Tables
Objects contain groups that contain both parameters and parameter tables. Use the following Tables to configure the Access Point. Columns used on the tables include: Name - Parameter, Group, or Table Name Type - Data type Values - Value range, and default value, if any Access = access type, R = Read Only (show), RW = Read-Write (can be set), W = Write Only CLI Parameter - Parameter name as used in the Access Point

156

Using the Command Line Interface (CLI)

Access Point network objects are associated with Groups. The network objects are listed below and associated parameters are described in the following Parameter Tables: System Parameters - Access Point system information Inventory Management Information - Hardware, firmware, and software version information Network Parameters - IP and Network Settings IP Configuration Parameters - Configure the Access Points IP settings DNS Client for RADIUS Name Resolution - Configure the Access Point as a DNS client DHCP Server Parameters - Enable or disable dynamic host configuration Link Integrity Parameters - Monitor link status Interface Parameters - Configure Wireless and Ethernet settings Wireless Interface Parameters Wireless Distribution System (WDS) Parameters - Configure the WDS partnerships Wireless Interface SSID/VLAN/Profile Parameters - Configure the SSID and VLAN pairs and the security and RADIUS profiles for each pair. Up to 16 pairs can be configured per wireless interface. Wireless Distribution System (WDS) Security Table Parameters Ethernet Interface Parameters - Set the speed and duplex of the Ethernet port Management Parameters - Control access to the APs management interfaces SNMP Parameters - Set read and read/write passwords HTTP (web browser) Parameters - Set up the graphical web browser interface. If required, enable SSL and configure the SSL certificate passphrase. Telnet Parameters - Telnet Port setup Serial Port Parameters - Serial Port setup RADIUS Based Management Access Parameters - Configure RADIUS Based Management Access for HTTP and Telnet access. SSH Parameters - Enable SSH and configure the host key. TFTP Server Parameters - Set up for file transfers; specify IP Address, file name, and file type IP Access Table Parameters - Configure range of IP addresses that can access the AP Auto Configuration Parameters - Configure the Auto Configuration feature which allows an AP to be automatically configured by downloading a configuration file from a TFTP server during boot up. Filtering Parameters Ethernet Protocol Filtering Parameters - Control network traffic based on protocol type Static MAC Address Filter Table - Enable and disable specific addresses Proxy ARP Parameters - Enable or disable proxy ARP for wireless clients IP ARP Filtering Parameters - Control which ARP messages are sent to wireless clients based on IP settings Broadcast Filtering Table - Control the type of broadcast packets forwarded to the wireless network TCP/UDP Port Filtering - Filter IP packets based on TCP/UDP port Alarms Parameters SNMP Table Host Table Parameters - Enter the list of IP addresses that will receive alarms from the AP Syslog Parameters - Configure the AP to send Syslog information to network servers Bridge Parameters Spanning Tree Parameters - Used to help prevent network loops Storm Threshold Parameters - Set threshold for number of broadcast packets Intra BSS Subscriber Blocking - Enable or disable peer to peer traffic on the same AP Packet Forwarding Parameters - Redirect traffic from wireless clients to a specified MAC address RADIUS Parameters Set RADIUS Parameters - Configure RADIUS Servers and assign them to VLANs. Security Parameters - Access Point security settings MAC Access Control Parameter - Control wireless access based on MAC address Rogue Access Point Detection (RAD) Parameters - Enable and configure Rogue Access Point Detection. Hardware Configuration Reset - Disable or enable hardware configuration reset and configure a configuration reset password.

157

Using the Command Line Interface (CLI)

VLAN/SSID Parameters - Enable the configuration of multiple subnetworks based on VLAN ID and SSID pairs. Security Profile Table - Configure Security Profiles that define allowed security modes (wireless clients), and encryption and authentication mechanisms. Other Parameters IAPP Parameters - Enable or disable the Inter-Access Point Protocol. SpectraLink VoIP Parameters (802.11b and bg Modes Only) - Enable or disable SpectraLink Voice over IP feature.

System Parameters
Name System Name Location Contact Name Contact E-mail Contact Phone FLASH Backup Interval Flash Update System OID Descriptor DisplayString DisplayString Type Group DisplayString DisplayString DisplayString DisplayString DisplayString Integer Values N/A User Defined User Defined User Defined User Defined User Defined max 254 characters 0 - 65535 seconds 0 1 N/A System Name, flash version, S/N, bootloader version dd:hh:mm:ss dd days hh hours mm minutes ss seconds Resets all parameters to default factory values Access R RW RW RW RW RW RW RW R R CLI Parameter system sysname sysloc sysctname sysctemail sysctphone sysflashbckint sysflashupdate sysoid sysdescr

Up Time

Integer

sysuptime

Emergency Restore to defaults

RW

sysresettodefaults Note: You must enter the following command twice to reset to defaults: set sysresettodefaults 1

158

Using the Command Line Interface (CLI)

Inventory Management Information
Name System Inventory Management Component Table Component Interface Table Type Subgroup Subgroup Subgroup Values N/A N/A N/A Access R R R CLI Parameter sysinvmgmt sysinvmgmtcmptbl sysinvmgmtcmpiftbl

NOTE
The inventory management commands display advanced information about the APs installed components. You may be asked to report this information to a representative if you contact customer support.

Network Parameters
IP Configuration Parameters
Name Network IP Configuration Type Group Group Values N/A N/A Access R R CLI Parameter network ip (Note: The network and ip parameters display the same information) ipaddr ipmask ipgw ipttl ipaddrtype

IP Address IP Mask Default Router IP Address Default TTL Address Type

IpAddress IpAddress IpAddress Integer Integer

User Defined User Defined User Defined User Defined (seconds) 64 (default) static dynamic (default)

RW RW RW RW RW

NOTE
The IP Address Assignment Type (ipaddrtype) must be set to static before the IP Address (ipaddr), IP Mask (ipmask) or Default Gateway IP Address (ipgw) values can be entered.

DNS Client for RADIUS Name Resolution

Name DNS Client DNS Client status Primary DNS Server IP Address Secondary DNS Server IP Address Default Domain Name Type Group Integer IpAddress IpAddress Integer32 Values N/A enable disable (default) User Defined User Defined User Defined (up to 254 characters) Access R RW RW RW RW CLI Parameter dns dnsstatus dnspridnsipaddr dnssecdnsipaddr dnsdomainname

159

Using the Command Line Interface (CLI)

DHCP Server Parameters
Name DHCP Server DHCP Server Status Type Group Integer Values N/A enable (1) (default) disable (2) delete (3) User Defined User Defined User Defined N/A Access R RW CLI Parameter dhcp dhcpstatus

Gateway IP Address Secondary DNS IP Address

IpAddress IpAddress

RW RW RW R

dhcpgw dhcppridnsipaddr dhcpsecdnsipaddr dhcpippooltblent

Primary DNS IP Address IpAddress

Number of IP Pool Table Integer32 Entries

NOTE
The DHCP Server (dhcpstatus) can only be enabled after a DHCP IP Pool table entry has been created.

DHCP Server table for IP pools

Name DHCP Server IP Address Pool Table Table Index Start IP Address End IP Address Width Default Lease Time (optional) Maximum Lease Time (optional) Comment (optional) Status (optional) Type Table Integer IpAddress IpAddress Integer Integer32 Integer32 DisplayString Integer Values N/A User Defined User Defined User Defined User Defined 360086400 sec (default) 360086400 sec (default) User Defined enable (1) disable (2) delete (3) Access R N/A RW RW RW RW RW RW RW CLI Parameter dhcpippooltbl index startipaddr endipaddr width defleasetm maxleasetm cmt status

NOTE
Set either End IP Address or Width (but not both) when creating an IP address pool.

160

Using the Command Line Interface (CLI)

Link Integrity Parameters
Name Link Integrity Link Integrity Status Link Integrity Poll Interval Link Integrity Poll Retransmissions Type Group Integer Integer Values N/A enable disable (default) 500 - 15000 ms (in increments of 500ms) 500 ms (default) 0 - 255 5 (default) Access R RW RW CLI Parameter linkint linkintstatus linkintpollint

Integer

RW

linkintpollretx

Link Integrity IP Target Table

Name Link Integrity IP Target Table Table Index Target IP Address Comment (optional) Status (optional) Type Table Integer IpAddress DisplayString Integer Values N/A 1-5 User Defined User Defined (up to 254 characters) enable disable (default) delete Access R N/A RW RW RW CLI Parameter linkinttbl index ipaddr cmt status

161

Using the Command Line Interface (CLI) Interface Parameters

Wireless Interface Parameters
The wireless interface group parameter is wif. For Dual-radio APs, Slot A uses table index 3 and Slot B uses table index 4.

Common Parameters to 802.11a, 802.11b, and 802.11b/g APs

Name Wireless Interfaces Table Index Network Name Type Group Integer DisplayString Values N/A 3 (Slot A) or 4 (Slot B) 2 31 characters My Wireless Network (default) enable (default) disable 1 255 1 = default 0 2347 Default is 2347 (off) 12 hex digits enable disable (default) 1 = resume 2= shutdown Depends on Regulatory Domain enable (default) disable Access R R RW CLI Parameter wif index netname

Auto Channel Select (ACS)1 DTIM Period RTS/CTS Medium Reservation MAC Address Closed System Wireless Service Status Supported Frequency Channels Load Balancing

Integer Integer Integer PhyAddress Integer Integer Octet String Integer

RW RW RW R RW RW R RW

autochannel dtimperiod medres macaddr closedsys wssstatus suppchannels ldbalance

Note 1: For 802.11a APs in Europe, Auto Channel Select is a read-only parameter; it is always enabled.

802.11a Only Parameters

Name Operating Frequency Channel Type Integer Values Varies by regulatory domain and country. See 802.11a Channel Frequencies See Transmit Rate, below 0 - Auto Fallback (default) 6 Mbits/sec 9 Mbits/sec 12 Mbits/sec 18 Mbits/sec 24 Mbits/sec 36 Mbits/sec 48 Mbits/sec 54 Mbits/sec ofdm (orthogonal frequency division multiplexing) for 802.11a enable disable (default) enable disable (default) Access RW CLI Parameter channel

Supported Data Rates Transmit Rate

Octet String Integer32

R RW

suppdatarates txrate

Physical Layer Type

Integer

phytype

SuperMode TurboMode

Integer Integer

RW RW

supermode turbomode

Note 1: Super Mode must be enabled first on the wireless interface before Turbo Mode can be enabled.

162

Using the Command Line Interface (CLI)

802.11b Only Parameters
Name Distance between APs Type Integer Values large (default) medium small minicell microcell enable (default) disable 1 - 14; available channels vary by regulatory domain/country; see 802.11b Channel Frequencies 1 Mbits/sec (1) 2 Mbits/sec (2) (default) 5.5 Mbits/sec (3) 11 Mbits/sec (4) enable disable (default) enable (default) disable 12 hex digits 1 Mbits/sec 2 Mbits/sec 5.5 Mbits/sec 11 Mbits/sec 0 (auto fallback - default) 1 Mbits/sec 2 Mbits/sec 5.5 Mbits/sec 11 Mbits/sec Depends on Regulatory Domain dsss (direct sequence spread spectrum) for 802.11b U.S./Canada -- FCC Europe -- ETSI Japan -- MKK Access RW CLI Parameter distaps

Interference Robustness Operating Frequency Channel

Integer Integer

RW RW

interrobust channel

Multicast Rate

Integer

RW

multrate

Closed Wireless System Medium Distribution MAC Address Supported Data Rates

Integer Integer PhyAddress Octet String

RW RW R R

closedsys meddendistrib macaddr suppdatarates

Transmit Rate

Integer32

RW

txrate

Supported Frequency Channels Physical Layer Type

Octet String Integer

R R

suppchannels phytype

Regulatory Domain List

DisplayString

regdomain

NOTE
There is an inter-dependent relationship between the Distance between APs and the Multicast Rate. In general, larger systems operate a lower average transmit rates.
Distance between APs Large Medium Small Minicell Microcell Multicast Rate 1 and 2 Mbits/sec 1, 2, and 5.5 Mbits/sec 1, 2, 5.5 and 11 Mbits/sec 1, 2, 5.5 and 11 Mbits/sec 1, 2, 5.5 and 11 Mbits/sec

163

Using the Command Line Interface (CLI)

802.11b/g Only Parameters
Name Wireless Operational Mode Type Integer Values dot11b-only dot11g-only dot11bg (default) dot11g-wifi 1 - 14; available channels vary by regulatory domain/country; see 802.11g Channel Frequencies See Transmit Rate, below For 802.11b-only mode: 0 (auto fallback - default) 1 Mbits/sec 2 Mbits/sec 5.5 Mbits/sec 11 Mbits/sec For 802.11g-only mode: 0 (auto fallback - default) 6 Mbits/sec 9 Mbits/sec 12 Mbits/sec 18 Mbits/sec 24 Mbits/sec 36 Mbits/sec 48 Mbits/sec 54 Mbits/sec For 802.11g-wifi and 802.11bg modes: 0 (auto fallback - default) 1 Mbits/sec 2 Mbits/sec 5.5 Mbits/sec 11 Mbits/sec 6 Mbits/sec 9 Mbits/sec 12 Mbits/sec 18 Mbits/sec 24 Mbits/sec 36 Mbits/sec 48 Mbits/sec 54 Mbits/sec ERP (Extended Rate Protocol) enable disable (default) enable disable (default) Access RW CLI Parameter mode

Operating Frequency Channel

Integer

RW

channel

Supported Data Rates Transmit Rate

Octet String Integer32

R RW

suppdatarates txrate

Physical Layer Type SuperMode TurboMode

Integer Integer Integer

R RW RW

phytype supermode turbomode

Note 1: Super Mode must be enabled first on the wireless interface before Turbo Mode can be enabled.

Wireless Distribution System (WDS) Parameters

Name WDS Table Port Index Status Partner MAC Address Type Table Integer Integer PhysAddress Values N/A 3.1 - 3.6 (Wireless) enable, disable User Defined Access R R RW RW CLI Parameter wdstbl portindex status partnermacaddr

164

Using the Command Line Interface (CLI)

Wireless Interface SSID/VLAN/Profile Parameters
The Wireless Interface SSID table manages the SSID/VLAN pairs, and the Security Profile and RADIUS Profiles associated to the VLAN

NOTE
The ability to configure up to 16 VLAN/SSID pairs and to configure security and RADIUS profiles per SSID is available only for 802.11b/g APs and 802.11a Upgrade Kit APs. 802.11b APs do not support multiple VLAN/SSID pairs. APs with the 802.11a card support multiple VLAN/SSID pairs, but do not support the security profile per SSID capability.
Name Type Values N/A Primary Wireless Interface = 3 Secondary Wireless Interface = 4 1 - 16 (SSID index) 0 - 32 characters -1 - 4094 Enable Disable Enable Disable Enable Disable Enable Disable 1-32 Access R R CLI Parameter wifssidtbl index Wireless Interface SSID Table Table Table Index Integer

Table Index SSID VLAN ID Table Row Status SSID Authorization Status per VLAN RADIUS Accounting Status per VLAN MAC ACL Status per VLAN Security Profile RADIUS MAC Profile RADIUS EAP Profile RADIUS Accounting Profile Deny Non Encrypted Data

Integer DisplayString VlanId RowStatus Integer Integer Integer Integer Integer Integer Integer Integer

R RW RW RW RW RW RW RW RW RW RW

ssidindex ssid vlanid status ssidauth acctstatus macaclstatus secprofile radmacprofile radeapprofile radacctprofile denynonencrypted

Enable Disable

R/W

Wireless Distribution System (WDS) Security Table Parameters

The WDS Security Table manages WDS related security objects.
Name WDS Security Table Table Index Type Table Integer Values N/A Primary Wireless Interface = 3 Secondary Wireless Interface = 4 none, wep N/A Access R R CLI Parameter wdssectbl index

Security Mode Encryption Key 0

Integer WEPKeyType

RW WO

secmode encryptkey0

165

Using the Command Line Interface (CLI)

Ethernet Interface Parameters
Name Ethernet Interface Speed Type Group Integer Values N/A 10halfduplex 10fullduplex 10autoduplex 100halfduplex 100fullduplex autohalfduplex autoautoduplex (default) N/A Access R RW CLI Parameter ethernet etherspeed

MAC Address

PhyAddress

ethermacaddr

Management Parameters
Secure Management Parameters
Name Secure Management Type Integer Values Enable/Disable Access RW CLI Parameter securemgmtstatus

SNMP Parameters
Name SNMP SNMP Management Interface Bitmask Type Group Interface Bitmask Values N/A 0 or 2 - no interfaces (disable) 1 or 3 - Ethernet 4 or 6 - Wireless A 8 or 10 - Wireless B 12 = Wireless A & B 13 or 15 - all interfaces (default is 15) User Defined public (default) max 63 characters User Defined public (default) max 63 characters User Defined public (default) max 63 characters User Defined public (default) max 63 characters Access R RW CLI Parameter snmp snmpifbitmask

Read Password

DisplayString

snmprpasswd

Read/Write Password

DisplayString

snmprwpasswd

SNMPv3 Authentication DisplayString Password SNMPv3 Privacy Password DisplayString

snmpv3authpasswd

snmpv3privpasswd

HTTP (web browser) Parameters

Name HTTP HTTP Management Interface Bitmask Type Group Interface Bitmask Values N/A 0 or 2 - no interfaces (disable) 1 or 3 - Ethernet 4 or 6 - Wireless A 8 or 10 - Wireless B 12 = Wireless A & B 13 or 15 - all interfaces (default is 15) Access R RW CLI Parameter http httpifbitmask

166

Using the Command Line Interface (CLI)

HTTP Password HTTP Port Help Link SSL Status SSL Certificate Passphrase DisplayString Integer DisplayString Integer DisplayString User Defined max 64 characters User Defined Default = 80 User Defined Enable/Disable User Defined W RW RW RW httppasswd httpport httphelplink sslstatus

Write-only sslpassphrase

NOTE
The default path for the Help files is C:/Program Files/ORiNOCO/AP/HTML/index.htm. (Use the forward slash character ("/") rather than the backslash character ("\") when configuring the Help Link location.) The AP Help information is available in English, French, German, Italian, Spanish, and Japanese.

Telnet Parameters
Name Telnet Telnet Management Interface Bitmask Type Group Interface Bitmask Values N/A 0 or 2 - no interfaces (disable) 1 or 3 - Ethernet 4 or 6 - Wireless A 8 or 10 - Wireless B 12 = Wireless A & B 13 or 15 - all interfaces (default is 15) User Defined 23 (default) 1 300 seconds 30 sec (default) 1 - 900 seconds 900 sec (default) Access R RW CLI Parameter telnet telifbitmask

Telnet Port Telnet Login Inactivity Time-out Telnet Session Idle Time-out

Integer Integer Integer

RW RW RW

telport tellogintout telsessiontout

Serial Port Parameters

Name Serial Baud Rate Type Group Integer Values N/A 2400, 4800, 9600 (default), 19200, 38400, 57600 8 none 1 none (default) xonxoff Access R RW CLI Parameter serial serbaudrate

Data Bits Parity Stop Bits Flow Control

Integer Integer Integer Value

R R R RW

serdatabits serparity serstopbits serflowctrl

167

Using the Command Line Interface (CLI)

RADIUS Based Management Access Parameters
The RADIUS Based Management Access parameters allow you to enable HTTP or Telnet Radius Management Access, enable or disable local user access, and configure the local user password. The default local user ID is root and the default local user password is public. Root cannot be configured as a valid user for RADIUS based management access when local user access is enabled.
Name Radius Local User Status Radius Local User Password HTTP Radius Management Access Telnet Radius Management Access Type Integer DisplayString Integer Integer Values Enable Disable User Defined Enable Disable Enable Disable Access RW RW RW RW CLI Parameter radlocaluserstatus radlocaluserpasswd httpradiusmgmtaccess telradiusmgmtaccess

SSH Parameters
The following commands enable or disable SSH and set the SSH host key.
Name SSH Status SSH Public Host Key Fingerprint SSH Host Key Status Type Integer DisplayString Integer Values Enable Disable User Defined Create Delete Access RW RW RW CLI Parameter sshstatus sshkeyfprint sshkeystatus

The AP SSH feature, open-SSH, confirms to the SSH protocol, and supports SSH version 2. The following SSH clients have been verified to interoperate with the APs server. The following table lists the clients, version number, and the website of the client.
Clients OpenSSH Putty Zoc Axessh Version V3.4-2 Rel 0.53b 5.00 V2.5 Website http://www.openssh.com http://www.chiark.greenend.org.uk http://www.emtec.com http://www.labf.com

For key generation, only the OpenSSH client has been verified.

168

Using the Command Line Interface (CLI)

Auto Configuration Parameters
These parameters relate to the Auto Configuration feature which allows an AP to be automatically configured by downloading a specific configuration file from a TFTP server during the boot up process.
Name Auto Configuration Auto Configuration Status Auto Config File Name Auto Config TFTP Server IP Address Type Group Integer DisplayString IpAddress Values N/A enable (default) disable User Defined User Defined Access R RW RW RW CLI Parameter autoconfig autoconfigstatus autoconfigfilename autoconfigTFTPaddr

TFTP Server Parameters

These parameters relate to upload and download commands. When a user executes an upload and/or download Command, the specified arguments are stored in TFTP parameters for future use. If nothing is specified in the command line when issuing subsequent upload and/or download commands, the stored arguments are used.
Name TFTP TFTP File Name TFTP File Type Type Group DisplayString Integer Values N/A User Defined User Defined img config bootloader sslcertificate sslprivatekey sshprivatekey sshpublickey clibatchfile (CLI Batch File) cbflog (CLI Batch Error Log) Access R RW RW RW CLI Parameter tftp tftpipaddr tftpfilename tftpfiletype

TFTP Server IP Address IpAddress

IP Access Table Parameters

When creating table entries, you may either specify the argument name followed by argument value or simply entering the argument value. When only the argument value is specified, then enter the values in the order depicted by the following table. CLI applies default values to the omitted arguments. Due to the nature of the information, the only argument that can be omitted is the comment argument.
Name IP Access Table Table Index IP Address IP Mask Comment (optional) Status (optional) Type Table Integer IpAddress IpAddress DisplayString Integer Values N/A User Defined User Defined User Defined User Defined enable (default) disable delete Access R N/A RW RW RW RW CLI Parameter mgmtipaccesstbl index ipaddr ipmask cmt status

169

Using the Command Line Interface (CLI) Filtering Parameters

Ethernet Protocol Filtering Parameters
Name Ethernet Filtering Filtering Interface Bitmask Type Group Interface Bitmask Values N/A 0 or 2 - no interfaces (disable) 1 or 3 - Ethernet 4 or 6 - Wireless A 8 or 10 - Wireless B 12 = Wireless A & B 13 or 15 - all interfaces (default is 15) passthru block Access R RW CLI Parameter etherflt etherfltifbitmask

Operation Type

RW

etherfltoptype

Ethernet Protocol Filtering Table

Identify the different filters by using the table index.
Name Ethernet Protocol Filtering Table Table Index Protocol Number Status (optional) Type Table N/A Octet String Integer Values N/A N/A N/A enable (1) disable (2) delete (3) Access R R RW RW RW CLI Parameter etherflttbl index protonumber protoname status

Protocol Name (optional) DisplayString

NOTE
The filter Operation Type (passthru or block) applies only to the protocol filters that are enabled in this table.

NOTE
The AP requires a reboot for changes to the Ethernet Protocol Filtering Table to take effect.

Static MAC Address Filter Table

Name Static MAC Address Filter Table Table Index Static MAC Address on Wired Network Static MAC Address Mask on Wired Network Static MAC Address on Wireless Network Static MAC Address Mask on Wireless Network Comment (optional) Status (optional) Type Table N/A PhysAddress PhysAddress PhysAddress PhysAddress Values N/A N/A User Defined User Defined User Defined User Defined Access R R RW RW RW RW CLI Parameter staticmactbl index wiredmacaddr wiredmask wirelessmacaddr wirelessmask

DisplayString Integer

max 255 characters enable (default) disable delete

RW RW

cmt status

170

Using the Command Line Interface (CLI)

Proxy ARP Parameters
Name Proxy ARP Status Type Group Integer Values N/A enable disable (default) Access R RW CLI Parameter parp parpstatus

IP ARP Filtering Parameters

Name IP ARP Filtering Status IP Address Subnet Mask Type Group Integer IpAddress IpAddress Values N/A enable disable (default) User Defined User Defined Access R RW RW RW CLI Parameter iparp iparpfltstatus iparpfltipaddr iparpfltsubmask

Broadcast Filtering Table

Name Broadcast Filtering Table Index Protocol Name Direction Type Table Integer DisplayString Integer Values N/A 1-5 N/A ethertowireless wirelesstoether both (default) enable disable (default) Access R N/A R RW CLI Parameter broadcastflttbl index protoname direction

Status

Integer

RW

status

TCP/UDP Port Filtering

The following parameters are used to enable/disable the Port filter feature.
Name Port Filtering Port Filter Status Type Group Integer Values N/A enable (default) disable Access R RW CLI portflt portfltstatus

TCP/UDP Port Filtering Table

The following parameters are used to configure TCP/UDP Port filters.
Name Port Filtering Table Table Index Type Table N/A Values N/A User Defined (there are also 4 pre-defined indices, see Port Number below for more information) tcp udp tcp/udp Access R R CLI portflttbl index

Port Type

Octet String

RW

porttype

171

Using the Command Line Interface (CLI)

Port Number Octet String User Defined (there are also 4 pre-defined protocols: Index 1: NetBios Name Service 137, Index 2: NetBios Datagram Service 138, Index 3: NetBios Session Service 139, Index 4: SNMP Service 161) User Defined (there are also 4 pre-defined protocols, see Port Number above) 0 or 2 - no interfaces (disable) 1 or 3 - Ethernet 4 or 6 - Wireless A 8 or 10 - Wireless B 12 = Wireless A & B 13 or 15 - all interfaces (default is 15) enable (default for new entries) disable (default for pre-defined entries) delete RW portnum

Protocol Name

DisplayString

RW

protoname

Interface Bitmask

Integer32

RW

ifbitmask

Status (optional)

Integer

RW

status

Alarms Parameters
SNMP Table Host Table Parameters
When creating table entries, you may either specifying the argument name followed by argument value. CLI applies default values to the omitted arguments. Due to the nature of the information, the only argument that can be omitted is the comment argument.

NOTE
Up to 10 entries can be added to the SNMP Trap Host Table.
Name SNMP Trap Host Table Table Index IP Address Password Comment (optional) Status (optional) Type Table Integer IpAddress DisplayString DisplayString Integer Values N/A User Defined User Defined User Defined (up to 64 characters) User Defined (up to 254 characters) enable (default) disable delete Access CLI Parameter R N/A RW W RW RW snmptraphosttbl index ipaddr passwd cmt status

Syslog Parameters
The following parameters configure the Syslog settings.
Name Syslog Syslog Status Syslog Port Type Group Integer Octet String Values N/A enable disable (default) 514 Access R RW R CLI syslog syslogstatus syslogport

172

Using the Command Line Interface (CLI)

Syslog Lowest Priority Logged Integer 17 1 = LOG_ALERT 2 = LOG_CRIT 3 = LOG_ERR 4 = LOG_WARNING 5 = LOG_NOTICE 6 = LOG_INFO (default) 7 = LOG_DEBUG enable (1) disable (2) (default) 1 604800 seconds; 900 sec. (default) RW syslogpritolog

Heartbeat Status

Integer

RW RW

sysloghbstatus sysloghbinterval

Heartbeat Interval (seconds) Integer

NOTE
The Heartbeat parameters are advanced settings not available via the HTTP interface. When Heartbeat is enabled, the AP periodically sends a message to the Syslog server to indicate that it is active. The frequency with which the heartbeat message is sent depends upon the setting of the Heartbeat Interval.

Syslog Host Table

The table described below configures the Syslog hosts that will receive message from the AP. You can configure up to ten Syslog hosts.
Name Syslog Host Table Table Index IP Address Comment (optional) Status (optional) Type Table Integer IpAddress DisplayString Integer Values N/A 1 10 User Defined User Defined enable disable delete Access R N/A RW RW RW CLI Parameter sysloghosttbl index ipaddr cmt status

Bridge Parameters
Spanning Tree Parameters
Name Spanning Tree Spanning Tree Status Bridge Priority Maximum Age Type Group Integer Integer Integer Values N/A enable (default) disable 0 65535 32768 (default) 600 4000 (in 0.01 sec intervals; i.e., 6 to 40 seconds) 2000 (default) 100 1000 (in 0.01 sec intervals; i.e., 1 to 10 seconds) 200 (default) 400 3000 (in 0.01 sec intervals; i.e., 4 to 30 seconds) 1500 (default) Access R RW RW RW CLI Parameter stp stpstatus stppriority stpmaxage

Hello Time

Integer

RW

stphellotime

Forward Delay

Integer

RW

stpfwddelay

Spanning Tree Priority and Path Cost Table

Name Spanning Tree Table Table Index (Port) Type Table N/A Values N/A 1 15 Access R R CLI Parameter stpbl index

173

Using the Command Line Interface (CLI)

Priority Path Cost State Integer Integer Integer 0 255 128 (default) 1 65535 100 (default) disable blocking listening learning forwarding broken enable disable RW RW R priority pathcost state

Status

Integer

RW

status

Storm Threshold Parameters

Name Storm Threshold Broadcast Threshold Multicast Threshold Type Group Integer Integer Values N/A 0 255 packets/sec (default is 0) 0 255 packets/sec (default is 0) Access N/A RW RW CLI Parameter stmthres stmbrdthres stmmultithres

Storm Threshold Table

Name Storm Threshold Table Table Index Broadcast Threshold Multicast Threshold Type Table Integer Integer Integer Values N/A 1 = Ethernet 3 = Wireless 0 255 packets/sec (default is 0) 0 255 packets/sec (default is 0) Access R R RW RW CLI Parameter stmthrestbl index bcast mcast

Intra BSS Subscriber Blocking

The following parameters control the Intra BSS traffic feature, which prevent wireless clients that are associated with the same AP from communicating with each other:
Name Intra BSS Traffic Intra BSS Traffic Operation Type Group Integer Values N/A passthru (default) block Access R RW CLI intrabss intrabssoptype

Packet Forwarding Parameters

The following parameters control the Packet Forwarding feature, which redirects wireless traffic to a specific MAC address:
Name Type Values N/A User Defined enable disable (default) 0 (any) (default) 1 (Ethernet) 2 (WDS 1) 3 (WDS 2) 4 (WDS 3) 5 (WDS 4) 6 (WDS 5) 7 (WDS 6) Access R RW RW RW CLI pktfwd pktfwdmacaddr pktfwdstatus pktfwdif

Packet Forwarding MAC Group Address Packet Forwarding MAC MacAddress Address Packet Forwarding Status Packet Forwarding Interface Port Integer Integer

174

Using the Command Line Interface (CLI)

NOTE
The Wireless Distribution System (WDS) feature is not available for 802.11a or 802.11b/g APs at this time.

Security Parameters
MAC Access Control Parameter
Name MAC Address Control Status Operation Type Type Group Integer Integer Values N/A enable disable (default) passthru (default) block Access R RW RW CLI Parameter macacl macaclstatus macacloptype

MAC Access Control Table

Name MAC Address Control Table Table Index MAC Address Comment (optional) Status (optional) Type Table N/A PhysAddress DisplayString Integer Values N/A N/A User Defined User Defined max 254 characters enable (default) disable delete Access R R RW RW RW CLI Parameter macacltbl index macaddr cmt status

RADIUS Parameters
General RADIUS Parameters
Name RADIUS Client Invalid Server Address Type Group Counter32 Values N/A N/A Access R R CLI Parameter radius radcliinvsvradd

RADIUS Server Configuration Parameters NOTE

Use a server name only if you have enabled the DNS Client functionality. See DNS Client for RADIUS Name Resolution.
Name RADIUS Authentication Table Index (Profile Index) Primary/Secondary Index Status Server Address Format Type Table Integer Integer Integer Integer Values N/A N/A Primary (1) Secondary (2) Enable Disable Ipaddr Name Access R R R RW RW CLI Parameter radiustbl index subindex status seraddrfmt

175

Using the Command Line Interface (CLI)

Server IP Address or Name IpAddress DisplayString User defined (enter an IP address if seraddrfmt is ipaddr or a name if set to name; up to 254 characters if using a name) User Defined 1812 (default) User Defined 6-32 characters 1 10 seconds 3 (default) 04 3 (default) dashdelimited colondelimited singledashdelimited nodelimiter 1-60 minutes 900-43200 seconds 10-3600 minutes RW ipaddr

Port (optional) Shared Secret Response Time (optional) Maximum Retransmissions (optional) RADIUS MAC Address Format

Integer DisplayString Integer Integer

RW W RW RW

port ssecret responsetm maxretx

Integer

RW

radmacaddrformat

RADIUS Accounting Inactivity Timer Authorization Lifetime RADIUS Accounting Update Interval VLAN ID

Integer32 Integer32 Integer32 vlanID

RW W RW RW

radaccinactivetmr radauthlifetm radacctupdinterval radvlanid

Rogue Access Point Detection (RAD) Parameters

Name Status Scan Interval Interface Bitmask Type N/A enable disable (default) 15-1440 (minutes) 4 (WiF A), 8 (WiF B), or 12 (both). Integer Integer Interface Bitmask Values R RW RW RW Access rad radstatus radscanint radifbitmask CLI Parameter Rogue Access Point Detection (RAD) Group

Hardware Configuration Reset

The Hardware Configuration Reset commands allows you to enable or disable the feature and to change the password to be used for configuration reset during boot up.
Name Hardware Configuration Reset Status Configuration Reset Password Type Integer DisplayString Values Enable (1) Disable (2) User Defined Access R RW CLI Parameter hwconfigresetstatus configresetpasswd

VLAN/SSID Parameters
Name VLAN Status Management ID Type Group Integer VlanId N/A enable disable (default) -1 (untagged) or 1-4094 Values R RW RW Access vlan vlanstatus vlanmgmtid CLI Parameter

176

Using the Command Line Interface (CLI) Security Profile Table

The Security Profile Table allows you to configure security profiiles. A maximum of 16 security profiles are supported per wireless interface. Each security profile can be enable and configure one or more security modes (None Secure Station, WEP Station, 802.1x Station, WPA Station, WPA-PSK Station). The WEP/PSK parameters are separately configurable for each security mode.
Name Security Profile Table Table Index Security Mode Type Table Integer Integer Values N/A 1.1 to 5.5 nonsecsta wepsta 802.1xsta wpasta wpapsksta none 802.1x radius acl psk none wep tkip aes User defined User defined User defined User defined 1-4 Access R R R CLI Parameter secprofiletbl index secmode

Authentication Mode

Integer

RW

authmode

Cipher

Integer

ciphersuite

Encryption Key 1 Encryption Key 2 Encryption Key 3 Encryption Key 4 Encryption Transmit Key Encryption Key Length Rekey Interval WPA PSK Value WPA PSK Pass Phrase RADIUS EAP Profile

Integer Integer Integer Integer Integer Integer Integer Integer Integer Integer

RW RW RW RW RW RW RW RW RW RW

secprofileencryptkey1 secprofileencryptkey2 secprofileencryptkey3 secprofileencryptkey4 encryptkeytx encryptkeylength rekeyint pskkey passphrase radeapprofile

Command Syntax and Examples of Configuring Security Profiles:

Configuring a Security Profile with Non Secure Security Mode
set secprofiletbl <index> secmode nonsecure status enable Example: set secprofiletbl 2 secmode nonsecure status enable

Configuring a Security Profile with WEP Security Mode

set secprofiletbl <index> secmode wep encryptkey0 <value> encryptkeylength <vakue> encryptkeytx <value> status enable Example: set secprofiletbl 3 secmode wep encryptkey0 12345 encryptkeylength 1 encryptkeytx 0 status enable

Configuring a Security Profile with 802.1x Security Mode

set secprofiletbl <index> secmode 802.1x rekeyint 900 status enable Example: set secprofiletbl 4 secmode 802.1x rekeyint 900 status enable

Configuring a Security Profile with WPA Security Mode

set secprofiletbl <index> secmode wpa rekeyint 900 status enable Example: set secprofiletbl 5 secmode wpa rekeyint 900 status enable

177

Using the Command Line Interface (CLI)

Configuring a Security Profile with WPA-PSK Security Mode
set secprofiletbl <index> secmode wpa-psk passphrase <value> status enable Example: set secprofiletbl 6 secmode wpa-psk passphrase 12345678 status enable

Configuring a Security Profile with 802.11i Security Mode

set secprofiletbl <index> secmode 802.11i rekeyint <value> status enable Example: set secprofiletbl 7 secmode 802.11i rekeyint 900 status enable

Configuring a Security Profile with 802.11i-PSK Security Mode

set secprofiletbl <index> secmode 802.11i-psk passphrase <value> status enable Example: set secprofiletbl 8 secmode 802.11i-psk passphrase 12345678 status enable

Other Parameters
IAPP Parameters
Name IAPP IAPP Status Periodic Announce Interval (seconds) Type Group Integer Integer Values N/A enable (default) disable 80 120 (default) 160 200 2 seconds 410 ms 512 ms (default) 614 ms 717 ms 819 ms 1 - 4 (default 4) enable (default) disable Access R RW RW CLI Parameter iapp iappstatus iappannint

Announce Response Time Handover Time-out

Integer Integer

R RW

iappannresp iapphandtout

Max. Handover Retransmissions Send Announce Request on Startup

Integer Integer

RW RW

iapphandretx iappannreqstart

NOTE
These parameters configure the Inter Access Point Protocol (IAPP) for roaming. Leave these settings at their default value unless a technical representative asks you to change them.

SpectraLink VoIP Parameters (802.11b and bg Modes Only)

These parameters enable or disable the SpectraLink Voice over IP feature. The Spectralink Legacy Support parameter should be enabled if the AP is operating in 802.11bg mode and legacy 802.11 Spectralink telephones are used. This parameter will set the basic rates of the AP to be 1 and 2 Mbps in 802.11bg mode and will allow old telephones that operate only at the 1 and 2 Mbps basic rate to connect to the AP.
Name Spectralink VoIP Spectralink VoIP Status Spectralink Legacy Support Type Group Integer Integer Values N/A enable disable (default) enable disable (default) Access R RW RW CLI Parameter spectralink speclinkstatus speclinklegacysupport

178

Using the Command Line Interface (CLI)

CLI Batch File

A CLI Batch file is a user-editable configuration file that provides a user-friendly way to change the AP configuration through a file upload. The CLI Batch file is an ASCII file that facilitates Auto Configuration because it does not require the user to access one of the APs management interfaces to make configuration changes as is required with the proprietary TLV format configuration file. The CLI Batch file does not replace the existing TLV format configuration file, which continues to define the configuration of the AP. The CLI Batch file contains a list of CLI commands that the AP will execute. The AP performs the commands in the file immediately after the file is uploaded to the AP manually or during Auto Configuration. The AP parses the file and executes the CLI commands. Commands that do not require a reboot take effect immediately, while commands that require a reboot (typically commands affecting a wireless interface) will take effect after reboot.

Auto Configuration and the CLI Batch File

The Auto Configuration feature allows download of the TLV format configuration file or the CLI Batch file. The AP detects whether the file uploaded is TLV format or a CLI Batch file. If the AP detects a CLI Batch file (a file with extension .cli), the AP executes the file immediately. The AP will reboot after executing the CLI Batch file. Auto Configuration will not result in repeated reboots if the CLI Batch file contains rebootable parameters.

CLI Batch File Format and Syntax

The CLI Batch file must be named with a .cli extension to be recognized by the AP. The maximum file size allowed is 100 Kbytes, and files with larger sizes cannot be uploaded to the AP. The CLI commands supported in the CLI Batch File are a subset of the legal AP CLI commands. The follow commands are supported: Set commands Reboot command (the reboot command ignores the argument (time)) Passwd command

Each command must be separated by a new line. Refer to Appendix A, CLI Command Reference for detailed command syntax.

NOTE
The following commands are not supported: Show command, Debug command, Undebug command, Upload command, Download command, Kill command, and the Exit, Quit, and Done commands.

Sample CLI Batch File

The following is a sample CLI Batch File: set sysname system1 set sysloc sunnyvale set sysctname contact1 set sysctphone 1234567890 set sysctemail [email protected] set ipaddr 11.0.0.66 set ipaddrtype static set ipsubmask 255.255.255.0 set ipgw 11.0.0.1 set wif 4 autochannel disable set wif 4 mode 1 set syslogstatus enable set sysloghbstatus enable set sysloghbinterval 5 set wif 4 netname london reboot

179

Using the Command Line Interface (CLI) Reboot Behavior

When a CLI Batch file contains a reboot command, the reboot will occur only after the entire CLI Batch file has been executed. There are two methods of uploading the CLI Batch File: Upload Upload and reboot (this option is to be used for a CLI Batch file containing the configuration parameters that require a reboot)

CLI Batch File Error Log

If there is any error during the execution of the CLI Batch file, the AP will stop executing the file. The AP generates traps for all errors and each trap contains the following information: Start of execution Original filename of the uploaded file End of execution (along with the status of execution) Line number and description of failures that occurred during execution

The AP logs all the errors during execution and stores them in the Flash memory in a CLI Batch File Error Log named CBFERR.LOG. The CLI Batch File Error Log can be downloaded though TFTP, HTTP, or CLI file transfer to a specified host.

180

ASCII Character Chart

B
ASCII Character Q R S T U V W X Y Z [ \ ] ^ _ ` a b c d e f g h Hex Equivalent 51 52 53 54 55 56 57 58 59 5A 5B 5C 5D 5E 5F 60 61 62 63 64 65 66 67 68 ASCII Character i j k l m n o p q r s t u v w x y z { | } ~ Hex Equivalent 69 6A 6B 6C 6D 6E 6F 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E

You can configure WEP Encryption Keys in either Hexadecimal or ASCII format. Hexadecimal digits are 0-9 and A-F (not case sensitive). ASCII characters are 0-9, A-F, a-f (case sensitive), and punctuation marks. Each ASCII character corresponds to two hexadecimal digits. The table below lists the ASCII characters that you can use to configure WEP Encryption Keys. It also lists the Hexadecimal equivalent for each ASCII character.
ASCII Character ! " # $ % & ' ( ) * + , . / 0 1 2 3 4 5 6 7 8 Hex Equivalent 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 ASCII Character 9 : ; < = > ? @ A B C D E F G H I J K L M N O P Hex Equivalent 39 3A 3B 3C 3D 3E 3F 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F 50

181

Specifications

Software Features Hardware Specifications Radio Specifications

Software Features
The tables below compare the software features available depending on the card type in the Access Point: Number of Stations per BSS Management Functions Advanced Bridging Functions Medium Access Control (MAC) Functions Security Functions Network Functions Advanced Wireless Functions

Number of Stations per BSS

Feature AP-2000 802.11b card up to 250 up to 250 up to 50 N/A AP-2000 5GHz Kit up to 250 up to 60 up to 44 N/A AP-2000 11a Kit up to 250 up to 120 up to 88 up to 27 AP-2000 802.11b/g card up to 250 up to 120 up to 88 up to 27

Without encryption With WEP encryption With 802.1x Authentication With WPA

Management Functions
Feature Web User Interface Telnet / CLI SNMP Agent TFTP 802.11b yes yes yes yes 802.11a yes yes yes yes 802.11b/g yes yes yes yes

182

Specifications Advanced Bridging Functions

Feature IEEE 802.1d Bridging WDS Relay Roaming Protocol Filtering Multicast/Broadcast Storm Filtering Proxy ARP TCP/UDP Port Filtering Blocking Intra BSS Clients Packet Forwarding 802.11b yes yes yes yes yes yes yes yes yes 802.11a yes yes yes yes yes yes yes yes yes 802.11b/g yes yes yes yes yes yes yes yes yes

Medium Access Control (MAC) Functions

Feature Automatic Channel Selection (ACS) Dynamic Frequency Selection (DFS) 1 Closed System Feature Wireless Service Shutdown TX Power Control 802.11b yes N/A yes yes N/A 802.11a yes yes yes yes Available with 802.11a upgrade kit. Not available with 5Ghz upgrade kit. 802.11b/g yes N/A yes yes yes

Note 1: A user cannot manually select a channel for products sold in Europe; these products require automatic channel selection using Dynamic Frequency Selection (DFS).

Security Functions
Feature Security Profiles per VLAN RADIUS Profiles per VLAN IEEE 802.11 WEP 1 MAC Access Control RADIUS Based Management Access Control RADIUS MAC-based Access Control IEEE 802.1x Authentication 2 Multiple Authentication Server Support per VLAN 4 Rogue Access Point Detection Per User Per Session (PUPS) Encryption 3 Wi-Fi Protected Access (WPA) 802.11b yes yes yes yes yes yes yes yes no N/A N/A 802.11a yes yes yes yes yes yes yes yes yes yes Available with 11a Upgrade KitNot available with 5 GHz Upgrade Kit 802.11b/g yes yes yes yes yes yes yes yes yes yes yes

Note 1: Key lengths supported by 802.11a: 64-bit, 128-bit, and 152-bit. Key lengths supported by 802.11b: 64-bit and 128-bit. Key lengths supported by 802.11b/g: 64-bit, 128-bit, and 152-bit. Note 2: EAP-MD5, EAP-TLS, EAP-TTLS, and PEAP client supplicant supported. Note 3: Use in conjunction with WPA or 802.1x Authentication. Note 4: Support is provided for a primary and backup RADIUS authentication server for both MAC-based authentication and 802.1x authentication.

183

Specifications Network Functions

Feature DHCP Client DHCP Server Inter Access Point Protocol (IAPP) Link Integrity System Logging (Syslog) RADIUS Accounting Support 1 DNS Client TCP/IP Protocol Support Virtual LAN Support 802.11b yes yes yes yes yes yes yes yes One VLAN ID per wireless interface 802.11a yes yes yes yes yes yes yes yes 802.11b/g yes yes yes yes yes yes yes yes

11a Upgrade Kit: Up to 16 Up to 16 VLAN IDs per VLAN IDs per wireless wireless interface interface 5 GHz Upgrade Kit: One VLAN ID per wireless Interface

Note 1: Includes Fallback to Primary RADIUS Server, RADIUS Session Timeout, RADIUS Multiple MAC Address Formats, RADIUS DNS Host Name Support, RADIUS Start/Stop Accounting.

Advanced Wireless Functions

Feature WEP Plus (Weak Key Avoidance) Remote Link Test Link Test Responder 2 Load Balancing 2 AP List 2 Medium Density Distribution 3 Distance between APs3 Interference Robustness SpectraLink VoIP Support 802.11b yes yes yes yes yes yes yes yes yes 802.11a yes yes 802.11b/g yes

Note 1: Available only one way (AP to client) if using an ORiNOCO ComboCard or a non-ORiNOCO client. Note 2: No client support in 802.11a or 802.11b/g. Note 3: This feature is not available if you are using an ORiNOCO ComboCard or a non-ORiNOCO client with an 802.11b AP.

Hardware Specifications
Physical Specifications
AP-2000 Unit
Dimensions (H x W x L) = 6.5 x 18.5 x 26 cm (2.5 x 7.25 x 10.25 in.) Weight = 1.75 Kg (3.5 lb.)

802.11a Antenna Adapter

Dimensions (H x W x L) = 11.3 x 2.10 x 26.2 cm (4.5 x 0.83 x 10.3in.) Weight = 0.18kg (0.4lb)

184

Specifications
Electrical Specifications
Without Active Ethernet Module
Voltage = 100 to 240 VAC (50-60 Hz) Current = 0.2 amp Power Consumption = 20 Watts

With Active Ethernet Module

Input Voltage = 42 to 60 VDC Output Current = 200mA at 48V Power Consumption = 9-10 Watts

Environmental Specifications
AP-2000 Unit
Operating = 0 to 40C (32 to 104 F) @ 20 to 90% relative humidity Transport = -40 to 60C (-40 to 140F) @ 15 to 95% relative humidity (no condensation allowed) Storage = -10 to 60C (14 to 140F) @ 10 to 90% relative humidity (no condensation allowed)

802.11a Antenna Adapter

Operating = 0 to 70C (32 to 158 F) @ 20 to 90% relative humidity Transport = -40 to 75C (-40 to 167 F) @ 15 to 95% relative humidity Storage = -20 to 75C (-4 to 167 F) @ 10 to 95% relative humidity

Ethernet Interface
10/100 Base-TX, RJ-45 female socket

Serial Port Interface

Standard RS-232C interface with DB-9, female connector

Active Ethernet Interface

Category 5, foiled, twisted pair cables must be used to ensure compliance with FCC Part 15, subpart B, Class B requirements Standard 802.3af pin assignments

HTTP Interface
Microsoft Internet Explorer 6 with Service Pack 1 or later Netscape 6.1 or later

Radio Specifications
802.11a Channel Frequencies 802.11b Channel Frequencies 802.11g Channel Frequencies Wireless Communication Range

NOTE
Refer to the Regulatory Flyer included with the AP for the latest regulatory information.

185

Specifications 802.11a Channel Frequencies

The available 802.11a Channels varies by regulatory domain and/or country. 802.11a radio certification is available in the following regions: FCC: U.S., Canada, and Australia ETSI: Europe and the United Kingdom TELEC: Japan SG: Singapore ASIA: China, Hong Kong, and South Korea TW: Taiwan

There are five sets of frequency bands that determine the available channels depending on the regulatory domain. Some countries restrict 802.11a operation to specific frequency bands. The Web interface and CLI display the available channels for a radio's particular regulatory domain. In the CLI, any channels that are not available are labeled "Not Supported".

NOTE
The original 5 GHz Upgrade Kit only supports the Lower and Middle U-NII bands. The 11a Upgrade Kit supports all of the frequency bands described below.
Frequency Band Lower Band (36 = default) Channel ID 34 36 38 40 42 44 46 48 Middle Band (52 = default) 52 56 58 60 H Band 100 104 108 112 116 120 124 128 132 136 140 Upper Band (149 = default) 149 153 157 161 ISM Band 165 FCC (GHz) 5.180 5.200 5.220 5.240 5.260 5.280 5.300 5.320 5.745 5.675 5.785 5.805 5.825 ETSI (GHz) 5.180 5.200 5.220 5.240 5.260 5.280 5.300 5.320 5.500 5.520 5.540 5.560 5.580 5.600 5.620 5.640 5.660 5.680 5.700 TELEC (GHz) 5.170 1 5.190 5.210 5.230 SG (GHz) 5.180 5.200 5.220 5.240 5.745 5.675 5.785 5.805 5.825 ASIA (GHz) 5.745 5.675 5.785 5.805 TW (GHz) 5.260 5.280 5.300 5.320 5.745 5.675 5.785 5.805 5.825

Note 1: Channel 34 is the default channel for Japan

186

Specifications 802.11b Channel Frequencies

The available 802.11b channels vary by regulatory domain and/or country. 802.11b radio certification is available in the following regions: FCC - U.S./Canada, Mexico, and Australia ETSI - Most of Europe, including the United Kingdom and some Eastern block countries MKK - Japan IL - Israel

Some countries restrict 802.11b operation to specific frequency bands. The web interface will always display the available channels depending in the cards regulatory domain. In the CLI, any channels that are not available are labeled "Not Supported".
Channel ID 1 2 3 4 5 6 7 8 9 10 11 12 13 14 FCC (GHz) 2.412 2.417 2.422 2.427 2.432 2.437 2.442 2.447 2.452 2.457 2.462 ETSI (GHz) 2.412 2.417 2.422 2.427 2.432 2.437 2.442 2.447 2.452 2.4571 2.4621 2.4671 2.4721 TELEC (GHz) 2.412 2.417 2.422 2.427 2.432 2.437 2.442 2.447 2.452 2.457 2.462 2.467 2.472 2.484 IL (GHz) 2.427 2.432 2.437 2.442 2.447 -

Note 1: France is restricted to these four channels.

802.11g Channel Frequencies

The available 802.11g channels vary by regulatory domain and/or country. 802.11g radio certification is available in the following regions: FCC - U.S./Canada, Mexico, and Australia ETSI - Europe and the United Kingdom ETSI - Europe, including the United Kingdom, China, and South Korea TELEC - Japan IL - Israel

Some countries restrict 802.11g operation to specific frequency bands. The web interface will always display the available channels depending in the cards regulatory domain. In the CLI, any channels that are not available are labeled "Not Supported".
Channel ID 1 2 3 4 5 6 7 8 9 10 11 FCC (GHz) 2.412 2.417 2.422 2.427 2.432 2.437 2.442 2.447 2.452 2.457 2.462 ETSI (GHz) 2.412 2.417 2.422 2.427 2.432 2.437 2.442 2.447 2.452 2.4571 2.4621 TELEC (GHz) 2.412 2.417 2.422 2.427 2.432 2.437 2.442 2.447 2.452 2.457 2.462 IL (GHz) 2.427 2.432 2.437 2.442 2.447 -

187

Specifications
Channel ID 12 13 14 FCC (GHz) ETSI (GHz) 2.4671 2.4721 TELEC (GHz) 2.467 2.472 2.4842 IL (GHz) -

Note 1: France is restricted to these channels. Note 2: Channel 14 is only available when using 802.11b only mode.

Wireless Communication Range

The range of the wireless signal is related to the composition of objects in the radio wave path and the transmit rate of the wireless communication. Communications at a lower transmit range may travel longer distances. The range values listed in the Communications Range Chart are typical distances as calculated by Proxims development team for FCC-certified products. These values provide a rule of thumb and may vary according to the actual radio conditions at the location where the product is used. The range of your wireless devices can be affected when the antennas are placed near metal surfaces and solid high-density materials. Range is also impacted due to obstacles in the signal path of the radio that may either absorb or reflect the radio signal. In Open Office environments, antennas can see each other (no physical obstructions between them). In Semi-open Office environments, workspace is divided by shoulder-height, hollow wall elements; antennas are at desktop level. In a Closed Office environment, solid walls and other obstructions may affect signal strength. The following tables show typical range values for various environments for FCC-certified products (range may differ for products certified in other regulatory domains).

802.11b
Range Open Office Semi-Open Office Closed Office Tx Power (dBm) Receiver Sensitivity (dBm) Antenna Gain 11 Mbits/s 142 m (466 ft.) 98 m (322 ft.) 67 m (220 ft.) 15 -82 5.5 Mbits/s 177 m (581 ft.) 122 m (400 ft.) 84 m (276 ft.) 15 -85 2 Mbits/s 219 m (718 ft.) 151 m (495 ft.) 104 m (341 ft.) 15 -88 1 Mbits/s 272 m (892 ft.) 187 m (614 ft.) 129 m (423 ft.) 15 -91

0 dBi (integrated diversity antenna module; 2.4-2.5 GHz)

Table C-1

802.11b Wireless communication ranges

188

Specifications
802.11a (5 GHz Upgrade Kit)
Range Open Office Semi-Open Office Closed Office Tx Power (dBm) Receiver Sensitivity (dBm) Antenna Gain 54 Mbits/ s 19 m (62 ft.) 13 m (43 ft.) 9m (30 ft.) 7 -65 48 Mbits/s 33 m (108 ft.) 23 m (75 ft.) 16 m (52 ft.) 11 -69 36 Mbits/s 55 m (180 ft.) 38 m (125 ft.) 26 m (85 ft.) 14 -73 24 Mbits/ s 74 m (243 ft.) 51 m (167 ft.) 35 m (115 ft.) 14 -77 18 Mbits/ s 92 m (302 ft.) 63 m (207 ft.) 43 m (141 ft.) 14 -80 12 Mbits/s 106 m (348 ft.) 73 m (239 ft.) 50 m (164 ft.) 14 -82 9 Mbits/ s 122 m (400 ft.) 84 m (276 ft.) 58 m (190 ft.) 14 -84 6 Mbits/ s 131 m (430 ft.) 90 m (295 ft.) 62 m (203 ft.) 14 -85

3.5 dBi (integrated diversity antennas; 5.15-5.35 GHz)

Table C-2

802.11a (5 GHz Upgrade Kit) Wireless communication ranges

802.11a (11a Upgrade Kit)

Range Open Office Semi-Open Office Closed Office Tx Power (dBm) Receiver Sensitivity (dBm) Antenna Gain 54 Mbits/ s 46 m (151 ft.) 32 m (105 ft.) 22 m (72 ft.) 15 -69 48 Mbits/s 62 m (203 ft.) 42 m (138 ft.) 29 m (95 ft.) 15 -73 36 Mbits/s 82 m (269 ft.) 57 m (187 ft.) 39 m (128 ft.) 15 -77 24 Mbits/ s 110 m (361 ft.) 75 m (246 ft.) 52 m (171 ft.) 15 -81 18 Mbits/ s 136 m (446 ft.) 94 m (308 ft.) 64 m (210 ft.) 15 -84 12 Mbits/s 169 m (554 ft.) 116 m (381 ft.) 80 m (262 ft.) 15 -87 9 Mbits/ s 181 m (594 ft.) 125 m (410 ft.) 86 m (282 ft.) 15 -88 6 Mbits/ s 195 m (640 ft.) 134 m (440 ft.) 92 m (302 ft.) 15 -89

4 dBi (integrated diversity antennas; 5.15-5.85 GHz)

Table C-3

802.11a (11a Upgrade Kit) Wireless communication ranges

189

Specifications
802.11b/g
Range 54 Mbits/s 56 m (184 ft.) 38 m (125 ft.) 48 Mbits/s 69 m (226 ft.) 48 m (157 ft.) 36 Mbits/s 107 m (351 ft.) 73 m (239 ft.) 24 Mbits/s 164 m (538 ft.) 113 m (371 ft.) 18 Mbits/s 219 m (718 ft.) 151 m (495 ft.) 12 Mbits/s 272 m (892 ft.) 187 m (614 ft.) 9 Mbits/s 292 m (958 ft.) 201 m (659 ft.) 6 Mbits/s 314 m (1030 ft.) 216 m (709 ft.) 11 Mbits/s 204 m (669 ft.) 140 m (459 ft.) 5.5 Mbits/s 236 m (774 ft.) 162 m (531 ft.) 2 Mbits/s 253 m (830 ft.) 174 m (571 ft.) 1 Mbits/s 338 m (1109 ft.) 232 m (761 ft.)

Open Office SemiOpen Office Closed Office Tx Power (dBm) Receiver Sensitivity (dBm) Antenna Gain

26 m (85 ft.) 12

33 m (108 ft.) 13

51 m (167 ft.) 14

78 m (256 ft.) 15

104 m (341 ft.) 15

129 m (423 ft.) 15

138 m (453 ft.) 15

149 m (489 ft.) 15

97 m (318 ft.) 15

111 m (364 ft.) 15

120 m (394 ft.) 15

160 m (525 ft.) 15

-68

-70

-75

-80

-84

-87

-88

-89

-83

-85

-86

-90

3 dBi (integrated diversity antenna module; 2.4-2.5 GHz)

Table C-4

802.11b/g Wireless communication ranges

190

Technical Support

If you are having a problem using an AP and cannot resolve it with the information in Troubleshooting the AP-2000, gather the following information and contact ORiNOCO Technical Support: List of ORiNOCO products installed on your network; include the following: Product names and quantity Part numbers (P/N) Serial numbers (S/N) List of ORiNOCO software versions installed Check the HTTP interfaces Version screen Include the source of the software version (e.g., pre-loaded on unit, installed from CD, downloaded from Proxim Web site, etc.) Information about your network Network operating system (e.g., Microsoft Networking); include version information Protocols used by network (e.g., TCP/IP, NetBEUI, IPX/SPX, AppleTalk) Ethernet frame type (e.g., 802.3, Ethernet II), if known IP addressing scheme (include address range and whether static or DHCP) Network speed and duplex (10 or 100 Mbits/sec; full or half duplex) Type of Ethernet device that the Access Points are connected to (e.g., Active Ethernet power injector, hub, switch, etc.) Type of Security enabled on the wireless network (None, WEP Encryption, 802.1x, Mixed) A description of the problem you are experiencing What were you doing when the error occurred? What error message did you see? Can you reproduce the problem? For each ORiNOCO product, describe the behavior of the devices LEDs when the problem occurs

You can reach ORiNOCO Technical Support as described below.

NOTE
Online support is available, and the latest software and documentation is available for download at http://support.proxim.com

For the U.S. and Canada:

Phone: International Phone: +1 408-542-5390 1-866-ORiNOCO (1-866-674-6626)

Europe, the Middle East, and Africa (EMEA):

Your local supplier in the EMEA region is trained to give you the support you require. Local suppliers have direct access to the ORiNOCO Technical Support Center and will help you in every way they can.

191

ORiNOCO AP-4000 User Guide

Statement of Warranty
Warranty Coverage

Proxim Corporation warrants that its Products are manufactured solely from new parts, conform substantially to specifications, and will be free of defects in material and workmanship for a Warranty Period of 1 year from the date of purchase.

Repair or Replacement
In the event a Product fails to perform in accordance with its specification during the Warranty Period, Proxim offers return-to-factory repair or replacement, with a thirty (30) business-day turnaround from the date of receipt of the defective Product at a Proxim Corporation Repair Center. When Proxim has reasonably determined that a returned Product is defective and is still under Warranty, Proxim shall, at its option, either: (a) repair the defective Product; (b) replace the defective Product with a refurbished Product that is equivalent to the original; or (c) where repair or replacement cannot be accomplished, refund the price paid for the defective Product. The Warranty Period for repaired or replacement Products shall be ninety (90) days or the remainder of the original Warranty Period, whichever is longer. This constitutes Buyers sole and exclusive remedy and Proxims sole and exclusive liability under this Warranty.

Limitations of Warranty
The express warranties set forth in this Agreement will not apply to defects in a Product caused; (i) through no fault of Proxim during shipment to or from Buyer, (ii) by the use of software other than that provided with or installed in the Product, (iii) by the use or operation of the Product in an application or environment other than that intended or recommended by Proxim, (iv) by modifications, alterations, or repairs made to the Product by any party other than Proxim or Proxims authorized repair partners, (v) by the Product being subjected to unusual physical or electrical stress, or (vii) by failure of Buyer to comply with any of the return procedures specified in this Statement of Warranty.

Support Procedures
Buyer should return defective LAN Products1 within the first 30 days to the merchant from which the Products were purchased. Buyer can contact a Proxim Customer Service Center either by telephone or via web. Calls for support for Products that are near the end of their warranty period should be made not longer than seven (7) days after expiration of warranty. Repair of Products that are out of warranty will be subject to a repair fee. Contact information is shown below. Additional support information can be found at Proxims web site at http://support.proxim.com. LAN Products1: Domestic calls: 866-674-6626 (24 hours per day, 7 days per week) International calls: 408-542-5390 WAN Products2: Domestic calls: 800-674-6626 (8:00 A.M. 5:00 P.M, M-F Pacific Time) International calls: 408-542-5390

When contacting the Customer Service for support, Buyer should be prepared to provide the Product description and serial number and a description of the problem. The serial number should be on the product. In the event the Customer Service Center determines that the problem can be corrected with a software update, Buyer might be instructed to download the update from Proxims web site or, if thats not possible, the update will be sent to Buyer. In the event the Customer Service Center instructs Buyer to return the Product to Proxim for repair or replacement, the Customer Service Center will provide Buyer a Return Material Authorization (RMA) number and shipping instructions. Buyer must return the defective Product to Proxim, properly packaged to prevent damage, shipping prepaid, with the RMA number prominently displayed on the outside of the container.
1 LAN products include: ORiNOCO 2 WAN products include: Lynx, Tsunami, Tsunami MP, Tsunami Quickbridge

192

Statement of Warranty
Calls to the Customer Service Center for reasons other than Product failure will not be accepted unless Buyer has purchased a Proxim Service Contract or the call is made within the first thirty (30) days of the Products invoice date. Calls that are outside of the 30-day free support time will be charged a fee of $25.00 (US Dollars) per Support Call. If Proxim reasonably determines that a returned Product is not defective or is not covered by the terms of this Warranty, Buyer shall be charged a service charge and return shipping charges.

Other Information
Search Knowledgebase
Proxim stores all resolved problems in a solution database at the following URL: http://support.proxim.com.

Ask a Question or Open an Issue

Submit a question or open an issue to Proxim technical support staff at the following URL: http://support.proxim.com/cgi-bin/proxim.cfg/php/enduser/ask.php.

Other Adapter Cards

Proxim does not support internal mini-PCI devices that are built into laptop computers, even if identified as "ORiNOCO" devices. Customers having such devices should contact the laptop vendor's technical support for assistance. For support for a PCMCIA card carrying a brand name other than Proxim, ORiNOCO, Lucent, Wavelan, or Skyline, Customer should contact the brand vendor's technical support for assistance.

193

ORiNOCO AP-4000 User Guide

Regulatory Information

This regulatory flyer contains the following sections: Information to the User Read this document prior to installation! User Documentation is provided on the CD-ROM. Informations pour lutilisateur Lisez ce document avant l'installation ! La documentation utilisateur est fournie sur le CD-ROM. Informazioni per lutente Legga questo documento prima dellinstallazione. La documentazione nella sua lingua contenuta nel CD-ROM. Informationen fr den Benutzer Bitte lesen Sie dieses Dokument vor der Installation sorgfltig durch! Die CD-ROM enthlt die erforderliche Benutzerdokumentation. Informacin para el usuario Lea este documento antes de realizar la instalacin! Encontrar la documentacin del usuario en su idioma en el CD-ROM.

Radio Approvals Certifications radio Omologazioni radio Funkgenehmigungen Permisos de utilizacin

194

Regulatory Information

Information to the User

This document provides regulatory information for the following products: Wireless Client products such as the PC Card. Wireless Base Station products such as the AP-200, AP-700, AP-1000, AP-4000, AP-4000 11a Upgrade Kit, AP-4000 11g Cardbus Kit, AP-600 11abg Upgrade Kit, AP-2500, AP-4000, ORiNOCO AP-600, AP-600 11g Upgrade Kit.

Wireless Client and Base Station products are wireless network products based on IEEE 802.11 standards for wireless LANs as defined and approved by the Institute of Electrical and Electronics Engineers. Products designed according the IEEE 802.11a and IEEE 802.11g standards standard use Orthogonal Frequency Division Multiplexing (OFDM) radio technology. Products designed according the IEEE 802.11b standard use Direct Sequence Spread Spectrum (DSSS) radio technology. These products are designed to be interoperable with any other wireless product that complies with the corresponding standard. The Wireless Fidelity (Wi-Fi) certification is defined by the Wi-Fi Alliance.

IMPORTANT SAFETY INSTRUCTIONS

When using this device, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: a. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. b. Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. c. Do not use this product to report a gas leak in the vicinity of the leak.

Additional Installation Requirements for Base Station products

When installing Base Stations the placement of the device must also satisfy the following installation requirements: a. Connect the unit to an AC wall outlet (100-240 V AC) using only the standard power cord/adapter provided with the product. b. Placement must allow for easily disconnecting the power cord/adapter of the device from the AC wall-outlet. c. Do not cover the device, or block the airflow to the device with any other objects. Keep the device away from excessive heat and humidity and keep the device free from vibration and dust. d. Installation must at all times conform to local regulations. e. Always disconnect the cables before opening the equipment enclosure or touching an uninsulated cable, jack or internal component. f. Connections to Base Station products can be made with either Unshielded Twisted Pair (UTP) or Shielded Twisted Pair cabling (STP) cabling. When using the device in combination with Power over Ethernet, only use Shielded Twisted Pair cabling (STP).

SAVE THESE INSTRUCTIONS

195

Regulatory Information Wireless LAN and your Health

Wireless LAN products, like other radio devices, emit radio frequency electromagnetic energy. The level of emitted energy however is far less than the electromagnetic energy emitted by other wireless devices like mobile phones, for example. Because Wireless LAN products operate within the guidelines found in radio frequency safety standards and recommendations, we believe that our Wireless LAN products are safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.

Regulatory Information
This device must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. For country-specific radio approvals or restrictions, please consult the section Radio Approvals of this flyer. In some situations or environments, the use of wireless devices may be restricted by the proprietor of the building or responsible representatives of the organization. These situations may for example include: Using the wireless equipment on board of airplanes, or In any other environment where the risk of interference to other devices or services is perceived or identified as harmful.

If you are uncertain of the policy that applies on the use of wireless equipment in a specific organization or environment (e.g. airports), you are encouraged to ask for authorization to use this device prior to turning on the equipment. The manufacturer is not responsible for any radio or television interference caused by unauthorized modification of the devices included with this kit, or the substitution or attachment of connecting cables and equipment other than specified by manufacturer. The correction of interference caused by such unauthorized modification, substitution or attachment will be the responsibility of the user. The manufacturer and its authorized resellers or distributors are not liable for any damage or violation of government regulations that may arise from failing to comply with these guidelines.

196

Regulatory Information

Informations pour lutilisateur

Ce document fournit des informations sur les rglementations concernant les produits suivants : Les produits client sans fil tels que PC Card. Les produits sans fil de la Base Station tels que AP-200, AP-700, AP-1000, AP-4000, AP-4000 11a Upgrade Kit, AP-4000 11g Cardbus Kit, AP-600 11abg Upgrade Kit, AP-2500, AP-4000, ORiNOCO AP-600, AP-600 11g Upgrade Kit.

Les produits client et de la Base Station sont des produits pour rseaux sans fil conus selon les normes IEEE 802.11 dfinies et approuves par lInstitute of Electrical and Electronics Engineers (IEEE). Les produits conus selon les normes IEEE 802.11b qui utilisent la technologie radio Direct Sequence Spread Spectrum (DSSS), cest--dire spectre tendu squence directe. Les produits conus selon les normes IEEE 802.11a et IEEE 802.11g utilisent la technologie radio Orthogonal Frequency Division Multiplexing (OFDM), cest--dire division multiplex de frquence orthogonale. Ces produits sont conus pour roperer avec n'importe quel autre produit sans fil qui est conforme la norme correspondante. Certification Wireless Fidelity (Wi-Fi) dfinie par la Wi-Fi Alliance.

INSTRUCTIONS IMPORTANTES CONCERNANT LA SECURITE

Quand vous utilisez ce dispositif, suivez toujours les prcautions de scurit lmentaires afin de rduire tout risque dincendie, de secousse lectrique et daccident, y compris les prcautions suivantes : a. Nutilisez pas ce produit proximit de leau, par exemple prs dune baignoire, dun lavabo, dun vier ou dune cuve linge, dans un sous-sol humide ou prs dune piscine. b. Evitez dutiliser ce produit en cas dorage magntique. Les clairs sont susceptibles de provoquer des secousses lectriques. c. Nutilisez pas ce produit pour signaler une fuite de gaz proximit de la fuite elle-mme.

Autres conditions dinstallation des produits de la Base Station

Quand vous installez une Base Station (station de base), lemplacement du dispositif doit galement satisfaire les conditions dinstallation suivantes : a. Branchez l'unit sur une prise murale CA (100-240 V CA) l'aide du cordon ou de l'adaptateur d'alimentation standard fourni avec l'unit. b. Lemplacement choisi doit permettre de dbrancher aisment le cordon ou ladaptateur dalimentation du dispositif de la prise murale CA. c. Ne couvrez pas le dispositif et ne bloquez pas le passage de lair vers les autres objets. Tenez le dispositif loign de toute source de chaleur et dhumidit et labri des vibrations et de la poussire. d. Linstallation doit toujours tre conforme aux rglementations locales. e. Dbranchez toujours les cbles avant douvrir lquipement ou de toucher un cble non isol, une prise ou un composant interne. f. Les connexions une Base Station (station de base) peuvent tre faites laide de cblages bifilaires torsads non blinds (Unshielded Twisted Pair ou UTP) ou de cblages bifilaires torsads blinds (Shielded Twisted Pair ou STP). Si vous utilisez le dispositif en combinaison avec la solution Power over Ethernet, utilisez uniquement des cblages bifilaires torsads blinds (Shielded Twisted Pair ou STP).

CONSERVEZ CES INSTRUCTIONS

197

Regulatory Information Rseaux sans fil et votre sant

Les produits pour un rseau sans fil, comme dautres dispositifs radio, mettent de lnergie lectromagntique de frquence radio. Le niveau dnergie mis par les dispositifs pour rsaeu sans fil est toutefois beaucoup moins lev que lnergie lectro-magntique mise par des dispositifs comme par exemple les tlphones portables. Puisque les produits pour rseau san fil fonctionnent selon les directives contenues dans les normes et recommandations de scurit en matire de frquence radio, nous considront que lutilisation de ces producits est sans danger pour les consommateurs. Ces normes et recommandations sont le reflet du consensus obtenu par la communaut scientifique et rsultent des dlibrations de groupes et de comits de scientifiques qui revoient et interprtent en permanence la masse dcrits sur le sujet.

Informations sur les rglementations

Ce dispositif doit absolument tre install et utilis conformment aux instructions dcrites dans la documentation utilisateur fournie avec le produit. Pour les certifications radio propres chaque pays, veuillez consulter la section Certifications radio de ce dpliant. Dans certaines situations ou environnements, lutilisation des dispositifs sans fil peut tre limite par le propritaire du btiment ou par les reprsentants responsables de la socit. Ces situations comprennent par exemple : lutilisation de lquipement sans fil bord davions ou dans tout autre environnement o le risque dinterfrence avec dautres dispositifs ou services est peru ou identifi comme nuisible.

Si vous avez des doutes concernant lutilisation dquipements sans fil dans lenvironnement spcifique dune socit (par ex. les aroports), veuillez demander lautorisation dutiliser le dispositif avant de lallumer. Le fabricant nest pas responsable des interfrences radio ou tlvision causes par une modification non autorise du dispositif compris dans ce kit ou par le remplacement ou le branchement de cbles et quipements de connexion autres que ceux spcifis par le fabricant. La correction des interfrences causes par de telles modifications, substitutions ou branchements non autoriss incombera lutilisateur. Le fabricant et ses revendeurs ou distributeurs autoriss ne sont pas responsables des dgts ou violations des rglementations gouvernementales qui peuvent dcouler de la non-observation de ces directives.

198

Regulatory Information

Informazioni per lutente

Questo documento contiene informazioni legali relative ai seguenti prodotti: Prodotti client wireless come la PC Card. Prodotti per Base Station wireless come il AP-200, AP-700, AP-1000, AP-4000, AP-4000 11a Upgrade Kit, AP-4000 11g Cardbus Kit, AP-2500, AP-4000, ORiNOCO AP-600, AP-600 11g Upgrade Kit, AP-600 11abg Upgrade Kit.

I prodotti cliente e delle Base Station sono prodotti senza fili della rete basati su IEEE 802.11 standard come definiti ed approvati dall'Institute of Electrical and Electronics Engineers. I prodotti hanno progettato conciliare la tecnologia radiofonica Direct Sequence Spread Spectrum (DSSS) di uso standard dello IEEE 802.11b. I prodotti hanno progettato conciliare la tecnologia radiofonica Orthogonal Frequency Division Multiplexing (OFDM) (divisione multiplex di frequenza ortogonale) di uso standard dello IEEE 802.11a e IEEE 802.11g. Questi prodotti sono destinati per funzionare con qualunque altro prodotto senza fili che aderisce allo standard corrispondente. Certificazione Wireless Fidelity (Wi-Fi), definita dalla Wi-Fi Alliance.

NORME DI SICUREZZA IMPORTANTI

Quando si usa questo dispositivo necessario rispettare sempre delle precauzioni di sicurezza fondamentali per ridurre il rischio di incendio, scosse elettriche o lesioni personali operando nel modo seguente: a. Non usare questo prodotto in prossimit di acqua, ad esempio vicino a una vasca da bagno, un lavandino, un lavello, una vasca per lavare, una piscina o in una cantina umida. b. Evitare di usare questo prodotto durante un temporale. Si potrebbe presentare un rischio remoto di scossa elettrica causata da un fulmine. c. Non usare questo prodotto per segnalare una perdita di gas nelle vicinanze della perdita stessa.

Requisiti supplementari per linstallazione dei prodotti Base Station

Le Base Station (stazioni base) vanno installate in un luogo che soddisfi anche i seguenti requisiti: a. Collegare l'unit a una presa murale AC (100-240 V AC) utilizzando il cavo di alimentazione/trasformatore standard in dotazione. b. La posizione di installazione deve consentire un facile scollegamento del cavo di alimentazione/trasformatore del dispositivo dalla presa murale AC. c. Non coprire il dispositivo e non ostruire il flusso daria verso il dispositivo con altri oggetti. Il luogo di installazione del dispositivo non deve essere vicino a fonti di calore o di umidit e non deve essere soggetto a vibrazioni o polvere. d. Linstallazione deve rispettare pienamente le normative locali. e. Scollegare sempre i cavi prima di aprire lapparecchiatura o di toccare un cavo, un connettore o un componente interno non isolato. f. I collegamenti al Base Station (stazioni base) possono essere effettuati con un cablaggio a coppia intrecciata non schermato (UTP) o schermato (STP). Se il dispositivo utilizzato in combinazione con Power over Ethernet, usare solo un cablaggio a coppia intrecciata schermato (STP).

CONSERVARE QUESTE ISTRUZIONI

199

Regulatory Information Wireless LAN e la salute

I prodotti LAN wireless, cos come altri dispositivi radio, emettono energia elettromagnetica in radiofrequenza. L'energia emessa tuttavia molto inferiore all'energia elettromagnetica emessa da altri dispositivi wireless come, ad esempio, i telefoni cellulari. Poich i prodotti LAN wireless funzionano entro i limiti previsti dalle norme e dalle raccomandazioni sulla sicurezza delle emissioni in radiofrequenza, riteniamo che l'uso dei nostri prodotti LAN wireless non comporti rischi per la salute degli utenti. Queste norme e raccomandazioni riflettono il consenso della comunit scientifica e derivano da deliberazioni di gruppi e comitati di scienziati che si occupano continuamente dell'analisi e dell'interpretazione della vasta letteratura di ricerca.

Informazioni legali
Questo dispositivo deve essere installato e utilizzato nel pieno rispetto delle istruzioni fornite dal costruttore, riportate nella documentazione in dotazione al prodotto. Per quanto riguarda le omologazioni dei prodotti radio per ciascun singolo paese, consultare la sezione Omologazioni radio di questo documento. In alcune situazioni o in determinati ambienti, luso di dispositivi wireless potrebbe essere limitato dal proprietario delledificio o dai responsabili dellazienda. Queste situazioni possono ad esempio includere i casi seguenti: Uso dellapparecchiatura wireless a bordo di aerei, oppure In qualsiasi altro ambiente in cui il rischio di interferenza con altri dispositivi o servizi sia percepito o identificato come dannoso.

In caso di dubbi sulle norme relative alluso di dispositivi radio in un ambiente specifico (es. aeroporti), si consiglia di richiedere lautorizzazione alluso del dispositivo prima di accendere lapparecchiatura. Il produttore non potr essere ritenuto responsabile per interferenze radio o TV causate da modifiche non autorizzate apportate ai dispositivi inclusi in questo kit oppure dalla sostituzione o dal collegamento di cavi o dispositivi diversi da quelli prescritti dal produttore. Leliminazione delle interferenze causate da tali modifiche, sostituzioni o collegamenti non autorizzati sar di responsabilit dellutente. Il produttore e i suoi rivenditori o distributori non potranno essere ritenuti responsabili per danni o violazioni di norme di legge causati dalla mancata osservanza di queste linee guida.

200

Regulatory Information

Informationen fr den Benutzer

Dieses Dokument enthlt wichtige Informationen ber folgende Produkte: Funk-Client-Produkte wie die PC Card. Funk-Base Stations-Produkte wie der AP-200, AP-700, AP-1000, AP-4000, AP-4000 11a Upgrade Kit, AP-4000 11g Cardbus Kit, AP-2500, AP-4000, ORiNOCO AP-600, AP-600 11g Upgrade Kit, AP-600 11abg Upgrade Kit.

Funk-Client- und Funk-Base Stations-Produkte sind die drahtlosen Netzprodukte, die auf IEEE 802.11 Standards basieren, wie definiert und durch das Institute of Electrical and Electronics Engineers genehmigt. Produkte konzipierten das bereinstimmen der Funktechnologie des IEEE 802.11b Standardgebrauch Direct Sequence Spread Spectrum (DSSS). Produkte konzipierten das bereinstimmen der Radiotechnologie des IEEE 802.11a und IEEE 802.11g Standardgebrauch Orthogonal Frequency Division Multiplexing (OFDM) (orthogonalen Frequenzvielfachs). Diese Produkte sind konzipiert, um mit jedem anderen drahtlosen Produkt zu funktionieren, das mit dem entsprechenden Standard bereinstimmt. WiFi-Zertifikat (Wireless Fidelity) der Wi-Fi Alliance.

WICHTIGE SICHERHEITSHINWEISE
Bei der Verwendung dieses Gerts sind die folgenden grundlegenden Sicherheitsvorkehrungen einzuhalten, um Gefahren wie Feuer, Stromschlge oder Personenschden zu vermeiden: a. Setzen Sie dieses Gert niemals in feuchten Umgebungen wie z. B. in der Nhe von Badewannen, Wasch- oder Splbecken, in feuchten Kellerrumen oder in der Nhe von Swimmingpools ein. b. Vermeiden Sie die Verwendung des Produkts bei Gewittern. Es besteht das wenn auch geringe Risiko von Stromschlgen durch Blitzeinschlag. c. Bei Lecks in Gasleitungen: Setzen Sie das Produkt niemals in der Nhe des Lecks ein.

Weitere Installationsvoraussetzungen fr Base Stationsprodukte

Bei der Installation von Base Station (Basisstationen) muss die Platzierung des Gerts auerdem folgende Installationsvoraussetzungen erfllen: a. Schlieen Sie das Gert an einer Wechselstrom-Wandsteckdose (100-240 V) an. Verwenden Sie dazu das im Lieferumfang enthaltene Standardnetzkabel bzw. den Standardadapter. b. Bringen Sie das Gert so an, dass das Netzkabel bzw. der Adapter jederzeit wieder leicht von der Wechselstrom-Wandsteckdose abgezogen werden kann. c. Decken Sie das Gert nicht ab, und blockieren Sie nicht die Luftzufuhr. Setzen Sie das Gert weder bermiger Hitze noch Feuchtigkeit, Vibrationen oder Staub aus. d. Beachten Sie bei der Installation stets die rtlichen Bestimmungen. e. Ziehen Sie immer alle Kabel vom Gert ab, bevor Sie das Gehuse des Gerts ffnen oder nicht isolierte Kabel, Buchsen oder interne Komponenten berhren. f. Die Verbindungen zum Base Station (Basisstationen) knnen entweder ber ein unabgeschirmtes Twisted-Pair (UTP)-Kabel oder ein abgeschirmtes Twisted-Pair (Shielded Twisted Pair, STP)-Kabel hergestellt werden. Wenn Sie das Gert zusammen mit unserer Power-over-Ethernet-Lsung einsetzen, mssen Sie immer ein abgeschirmtes Twisted-Pair (STP)-Kabel verwenden.

BEWAHREN SIE DIESE ANWEISUNGEN AN EINEM SICHEREN ORT AUF

201

Regulatory Information Funk-LAN und gesundheitliche Sicherheit

Funk-LAN-Produkte geben wie alle Hochfrequenzgerte elektromagnetische Hochfrequenzenenergie ab. Bei Funk-LAN-Gerten ist jedoch eine deutlich geringere Emission elektromagnetischer Energie zu verzeichnen als bei anderen Funkgerten, wie z. B. Mobiltelefonen. Da die Funk-LAN-Produkte den Richtlinien der HF-Sicherheitsstandards und -empfehlungen entsprechen, besteht beim Gebrauch von Funk-LAN-Produkten keine Gefhrdung fr den Kunden. Diese Standards und Empfehlungen basieren auf wissenschaftlichen Erkenntnissen und sind das Ergebnis von Beratungen verschiedener Wissenschaftsgremien und -komitees, die sich laufend mit der umfangreichen Forschungsliteratur beschftigen und diese auswerten.

Rechtliche Hinweise
Die Installation und der Gebrauch dieses Gerts mssen streng nach den Anweisungen des Herstellers erfolgen, die in der Benutzerdokumentation zu diesem Produkt zu finden sind. Die lnderspezifischen Funkzulassungen finden Sie im Abschnitt Funkgenehmigungen dieses Dokumentes. In bestimmten Situationen oder Umgebungen ist der Gebrauch von Funkgerten mglicherweise durch den Gebudeeigentmer oder verantwortliche Personen des Unternehmens untersagt. Nicht gestattet ist zum Beispiel: der Betrieb von Funkgerten an Bord eines Flugzeuges oder der Betrieb von Funkgerten in jeder anderen Umgebung, in der das Risiko, dass der Betrieb oder der Empfang anderer Gerte gestrt wird, besteht oder als mglich angesehen wird.

Falls Sie die Vorschriften fr die Verwendung von Funkgerten in einem bestimmten Unternehmen oder in einer bestimmten Umgebung (z. B. Flughfen) nicht genau kennen, bitten Sie um Erlaubnis, bevor Sie das Gert einschalten. Der Hersteller bernimmt keine Haftung fr Funk- oder Fernsehstrungen, die durch unzulssige nderungen an den in diesem Paket enthaltenen Gerten auftreten oder durch den Austausch und Anschluss von anderen als den vom Hersteller genannten Anschlusskabeln und Gerten verursacht werden. Die Verantwortung fr die Behebung der durch ein solches ndern, Austauschen oder Anschlieen hervorgerufenen Strungen trgt der Benutzer. Der Hersteller, seine autorisierten Hndler oder Vertriebspartner haften nicht fr Schden oder Verletzungen staatlicher Vorschriften, die sich aus der Nichteinhaltung dieser Richtlinien ergeben.

202

Regulatory Information

Informacin para el usuario

Este documento incluye informacin sobre normativas acerca de los siguientes productos: Productos cliente inalmbricos como la PC Card. Productos de Base Station inalmbricos como el AP-200, AP-700, AP-1000, AP-4000, AP-4000 11a Upgrade Kit, AP-4000 11g Cardbus Kit, AP-2500, AP-4000, ORiNOCO AP-600, AP-600 11g Upgrade Kit, AP-600 11abg Upgrade Kit.

Los productos del cliente sin hilos y de la estacin baja son productos sin hilos de la red basados en IEEE 802.11 estndares para LANs sin hilos segn lo definidos y aprobados por el Institute of Electrical and Electronics Engineers. Los productos disearon acordar la tecnologa de radio espectro ensanchado en secuencia directa (DSSS) del uso estndar de IEEE 802.11b. Los productos disearon acordar la tecnologa de radio Orthogonal Frequency Division Multiplexing (OFDM) (multiplexacin de divisin de frecuencia orthogonale) del uso estndar de IEEE 802.11a y IEEE 802.11g. Estos productos se disean para funcionar con cualquier otro producto sin hilos que se conforme con el estndar correspondiente. La certificacin Wi-Fi (Wireless Fidelity Fidelidad inalmbrica) definida por la Wi-Fi Alliance.

INSTRUCCIONES DE SEGURIDAD IMPORTANTES

Deben cumplirse las siguientes precauciones de seguridad en el manejo de este dispositivo cuyo objetivo es reducir el riesgo de incendio, descarga elctrica y daos personales: a. No utilice este producto cerca del agua, por ejemplo, cerca de una baera, lavadero, fregadero o lavadora, en un stano hmedo o cerca de una piscina. b. Evite su utilizacin durante una tormenta con aparato elctrico. Existe el riesgo de una descarga elctrica debida a los rayos. c. No utilice este producto para informar sobre un escape de gas cerca del mismo.

Requisitos de instalacin adicionales para los productos de Base Station

En las instalaciones de Base Station (estaciones base), la colocacin del dispositivo debe cumplir adems los siguientes requisitos de instalacin: a. Conecte la unidad a una toma de corriente de pared de Corriente Alterna (CA) (100-240 V CA) solo mediante el cable de alimentacin estndar y/o el adaptador que se suministra con la unidad. b. La unidad debe colocarse de modo que se pueda desconectar el cable de alimentacin o adaptador fcilmente de la toma de corriente de pared de CA. c. No tape la unidad ni bloquee la entrada de ventilacin con ningn objeto. Mantenga la unidad apartada de fuentes de calor y humedad excesivos y en un lugar sin vibraciones ni polvo. d. La instalacin debe cumplir en todas las ocasiones con las normas locales. e. Desconecte todos los cables antes de abrir la tapa o tocar cables sin aislante, enchufes o cualquier componente interno. f. La conexin con el Base Station (estaciones base) puede realizarse mediante un cable de par trenzado no apantallado (UTP) o un cable de par trenzado apantallado (STP). Si utiliza el dispositivo en combinacin con la solucin Power over Ethernet, utilice siempre un cable de par trenzado apantallado (STP).

GUARDE ESTAS INSTRUCCIONES

203

Regulatory Information LAN inalmbrica y su salud

Los productos de LAN inalmbrica, al igual que otros dispositivos de radiotecnologa, emiten energa electromagntica de radiofrecuencia. Sin embargo, el nivel de energa que emiten es mucho menor que la energa electromagntica emitida por otros dispositivos inalmbricos, como por ejemplo los telfonos mviles. Debido a que los productos de LAN inalmbrica operan de conformidad con las pautas fijadas en las normas y recomendaciones de seguridad de radiofrecuencia, creemos que nuestros productos de LAN inalmbrica son seguros para los consumidores. Estas normas y recomendaciones reflejan el consenso de la comunidad cientfica y son el resultado de deliberaciones de grupos y comits de cientficos que continuamente revisan e interpretan la extensa documentacin de investigacin.

Informacin sobre normativas

Este dispositivo debe instalarse y utilizarse siguiendo exactamente las instrucciones del fabricante incluidas en la documentacin del usuario que se entrega con el producto. El apartado Permisos de utilizacin de este folleto, incluye las normas especficas de cada pas. Puede que, en algunas situaciones o entornos, el propietario del edificio o los responsables de la organizacin restrinjan el uso de dispositivos inalmbricos. Estas situaciones pueden incluir: El uso del equipo inalmbrico en aviones o En cualquier otro entorno donde se supone o se ha determinado que el riesgo de interferencias con otros dispositivos o servicios es peligroso.

Si no est seguro de la norma que rige el uso de dispositivos inalmbricos en una organizacin o en un entorno especfico, por ejemplo, en los aeropuertos, se recomienda que solicite autorizacin para utilizar el dispositivo antes de poner en marcha el equipo. El fabricante no es responsable de ninguna interferencia de radio o televisin causada por la modificacin no autorizada de los dispositivos incluidos en este kit, o la sustitucin o conexin de cables y equipo no especificada por el propio fabricante. El usuario ser responsable de corregir la interferencia causada por cualquier modificacin, sustitucin o conexin sin autorizacin. El fabricante y sus distribuidores o proveedores no son responsables de los daos o infracciones de las leyes gubernamentales que puedan producirse por el incumplimiento de estas directrices.

204

Regulatory Information

PC Card AP-200, AP-700, AP-1000, AP-4000, AP-4000 11a Upgrade Kit, AP-4000 11g Cardbus Kit, AP-2500, AP-4000, ORiNOCO AP-600, AP-600 11g Upgrade Kit, AP-600 11abg Upgrade Kit, Base Station . Base Station (IEEE) LAN IEEE 802.11 IEEE 802.11a/802.11g (OFDM) IEEE 802.11b (DSSS) Wi-Fi Alliance Wi-Fi (Wireless Fidelity)

a. b. c.

Base Station
a.100-240 V AC b.AC / c. d. e. f.Base Station (UTP) (STP) (STP)

205

Regulatory Information
LAN
LAN LAN LAN

206

Regulatory Information

United States FCC Information

Federal Communications Commission (FCC) Declaration of Conformity
Products marked with the FCC logo and comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Operation of this device is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference that may cause undesired operation. Products that contain a radio transmitter are marked with FCC ID number and may also carry the FCC logo.

Warnings
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the distance between the equipment and the receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

In some situations or environments, the use of wireless devices may be restricted by the proprietor of the building or responsible representatives of the organization. These situations may for example include the use of wireless equipment on board of airplanes, or in any other environment where the risk of interference to other devices or services is perceived or identified as harmful. If you are uncertain of the policy that applies on the use of wireless equipment in a specific organization or environment (e.g. airports), you are encouraged to ask for authorization to use this device prior to turning on the equipment.

Caution: Exposure to Radio Frequency Radiation

To comply with the FCC radio frequency exposure requirements, the following antenna installation and device operating configurations must be satisfied: a. For client devices using an integral antenna, the separation distance between the antenna(s) and any persons body (including hands, wrists, feet and ankles) must be at least 2.5 cm (1 inch). b. For base stations and configurations using an approved external antenna, the separation distance between the antenna and any persons body (including hands, wrists, feet and ankles) must be at least 20 cm (8 inch). The transmitter shall not be collocated with other transmitters or antennas.

Modifications
The FCC requires the user to be notified that any changes or modifications to this device that are not expressly approved by the manufacturer may void the users authority to operate the equipment. The correction of interference caused by unauthorized modification, substitution or attachment will be the responsibility of the user. The manufacturer and its authorized resellers or distributors are not liable for any damage or violation of government regulations that may arise from failing to comply with these guidelines.

207

Regulatory Information

Canada IC Information
Industry Canada (IC)
This device complies with the limits for a class B digital device and conforms to Industry Canada standard ICES-003. Products that contain a radio transmitter comply with Industry Canada standard RSS 210 and are labelled with IC approval number. Wireless LAN products designed according the IEEE 802.11b or IEEE 802.11g standard additionally comply with Industry Canada standard RSS 139. Cet appareil numrique de classe B est conforme la norme ICES-003 de Industry Canada. La radio sans fil de ce dispositif est conforme la certification RSS 210 de Industry Canada et est tiquete avec un numro d'approbation IC. Les produits pour rseaux sans fil qui utilisent la norme IEEE 802.11b ou IEEE 802.11g sont en plus conformes la certification RSS 139 de Industry Canada.

Product Safety
ETL or UL listed products conform to ANSI/UL STD.1950 certified to CAN/CSA STD C22.2 NO.950. Les produits rpertoris ETL ou UL sont conformes ANSI/UL STD.1950 certifis selon la norme CAN/CSA STD C22.2 NO.950.

208

Regulatory Information

Europe Information
Products labeled with the CE mark comply with EMC Directive 89/336/EEC and the Low Voltage Directive 73/23/EEC implying conformity to the following European Norms. Tous les produits portant la marque CE sont conformes la directive EMC 89/336/EEC et la directive 73/23/EEC sur les basses tensions qui impliquent la conformit aux normes de la Commission de la Communaut Europenne. Tutti i prodotti con il marchio CE sono conformi alle direttive EMC 89/336/EEC e direttive Bassa tensione 73/23/EEC che rispetto le norme dalla Commissione della Comunit Europea. Produkte mit der CE Kennzeichnung erfllen die EMV Richtlinie 89/336/EEC sowie die Niederspannungsrichtlinie 73/23/EEC, implizieren die Erfllung der Normen der EU-Kommission. Todos los productos con la marca CE cumplen con la directiva de compatibilidad electromagntica EMC 89/336/EEC y la directiva de baja tensin 73/23/EEC y implica conformidad con las normas de la Comisin de la Unin Europea. EN 60950 (IEC60950) - Product Safety EN 55022 (CISPR 22) - Electromagnetic Interference EN 55024 (IEC61000-4-2,3,4,5,6,8,11) - Electromagnetic Immunity EN 61000-3-2 (IEC610000-3-2) - Power Line Harmonics EN 61000-3-3 (IEC610000-3-3) - Power Line Flicker Products labeled with the CE 0XXX (!) contain a radio transmitter that complies with the R&TTE Directive 1999/5/EC implying conformity to the following European Norms. Les produits portant la marque CE 0XXX (!) contiennent un metteur radio conforme la directive R&TTE 1999/5/EC qui impliquent la conformit aux normes de la Commission de la Communaut Europenne. I prodotti che recano lavvertenza CE 0XXX (!) contengono un trasmettitore radio conforme alla Direttiva R&TTE 1999/5/EC emessa dalla Commissione della Comunit Europea. Funkprodukte mit der CE 0XXX (!) Kennzeichnung enthalten einen Funktransmitter, der die von der Kommission der EU verabschiedete Richtlinie R&TTE 1999/5/EC erfllt. Los productos con la marca CE 0XXX (!) contienen un transmisor de radio que cumple con la Directiva R&TTE 1999/5/EC emitida por la Comisin Europea. EN 60950 (IEC60950) - Product Safety ETSI EN 300328 - Radio LAN equipment operating in the 2.4 Ghz band ETSI EN 301893 - Radio LAN equipment operating in the 5 Ghz band ETSI EN 300826 or ETSI EN 301489-17 - General EMC requirements for radio equipment To determine the type of transmitter, check the product identification label on your Wireless LAN product. Pour identifier le type dmetteur, reportez-vous ltiquette didentification de votre produit. Per determinare il tipo di trasmettitore, controllare la targhetta di identificazione del prodotto. Um welchen Transmittertyp es sich handelt, knnen Sie auf dem Typenschild auf dem Produkt ablesen. Para determinar el tipo de transmisor, compruebe la etiqueta de identificacin del producto.

209

Regulatory Information
Proxim 802.11a Base Station products sold in Europe use a technique called Dynamic Frequency Selection (DFS) to automatically select an operating channel. The European Telecommunications Standard Institute (ETSI) requires that 802.11a devices use DFS to prevent interference with radar systems and other devices that already occupy the 5 GHz band. Les produits de la Proxim 802.11a Base Station vendues en Europe utilisent une technique dnomme Slection de frquence dynamique (Dynamic Frequency Selection, DFS) pour qu'un canal de fonctionnement soit automatiquement choisi. Le l'institut europen des standards de tlcommunications (European Telecommunications Standard Institute, ETSI) exige que les priphriques 802.11a utilisent DFS pour empcher toute interfrence avec les systmes radar et d'autres priphriques qui occupent dj la bande des 5 GHz. Le unit Proxim 802.11a Base Station vendute in Europa impiegano una tecnologia denominata Selezione di frequenza dinamica (Dynamic Frequency Selection, DFS) per la selezione automatica del canale operativo. L'Istituto europeo di standardizzazione delle telecomunicazioni (European Telecommunications Standard Institute, ETSI) sancisce che tutti i dispositivi 802.11a devono usare la DFS per prevenire eventuali interferenze con sistemi radar ed altri dispositivi che gi occupano la banda de 5 GHz. Die in Europa vertriebenen Proxim 802.11a Base Station-Gerte verwenden die so genannte dynamische Frequenzauswahl (Dynamic Frequency Selection, DFS), um automatisch einen gltigen Betriebskanal auszuwhlen. Das European Telecommunications Standard Institute (European Telecommunications Standard Institute, ETSI) schreibt vor, dass 802.11a-Gerte DFS verwenden, um Strungen in Radarsystemen und anderen Gerten, die das 5-GHz-Band verwenden, zu vermeiden. Las unidades Proxim 802.11a Base Station vendidas en Europa usan una tcnica llamada Seleccin dinmica de frecuencias (Dynamic Frequency Selection, DFS) para seleccionar automticamente un canal de operacin. El Instituto Europeo de Normas de Telecomunicaciones (European Telecommunications Standard Institute, ETSI) requiere que los dispositivos 802.11a usen DFS para evitar las interferencias con sistemas de radar y otros dispositivos que ya ocupan la banda de 5 GHz. Some European countries using this product may be subject to specific restrictions as listed in the Radio Approvals section. Dans certains pays, lutilisation du produit peut tre subordonne des conditions spcifiques comme indiques dans la section Certifications radio. In alcuni paesi luso del prodotto pu essere soggetto a limitazioni specifiche, come indicato nelle sezioni Omologazioni radio. In einigen Lndern kann der Betrieb dieses Produktes bestimmten Beschrnkungen unterliegen, wie sie in dem Abschnitt Funkgenehmigungen. En algunos pases la utilizacin de este producto puede estar sujeta a restricciones concretas, tal y como se describe en el apartado Permisos de utilizacin.

210

Regulatory Information

Japan Information
Association of Radio Industries and Businesses (ARIB)
(ARIB) STD-T71) 5.15 ~ 5.25 GHz IEEE 802.11a Radio Approvals (ARIB) STD-T66) 2.4 GHz IEEE 802.11b Radio Approvals (DSSS) 2.400 2.483 MHz (RF-ID) 1 LAN (RF-ID) 40 2 (RF-ID) RF (RF-ID) RF 3 (RF-ID) Web http://www.proxim.com

211

Regulatory Information

South Korea Information

(Product Name) PC Card AP-500 AP-600a AP-600b AP-600g AP-600abg AP-1000 AP-4000 AP-2500 AS-2000 AP-700 AP-4000 (Model Name) PC24E-H-FC PC24E-11-FC/R AP-500 Alpha-1 Alpha-1 Alpha-1 Alpha-1 AP-II E AP-2000 AP-2000 AS-2000 AP-AG-AT-01 AP-AG-AT-02
Class (A)

(Trade Name/Manufacturer) Agere Systems Agere Systems Agere Systems Proxim Corporation Proxim Corporation Proxim Corporation Proxim Corporation Agere Systems Proxim Corporation Proxim Corporation Agere Systems Proxim Corporation / USI Proxim Corporation / USI

(Certification No.) R-LARN-01-028 R-LARN-02-0027 E-E900-01-4590 E-E900-03-2111 (B) E-E900-03-2111 (B) E-E900-03-2111 (B) E-E900-03-2111 (B) E-E900-01-4591 E-F900-01-5918 (B) E-F900-03-1500 (B) E-F900-02-0043 (B) pending pending

(Date of Certification) 2001.10.15 2002.01.26 2001.10.13 2003.05.15 2003.05.15 2003.05.15 2003.05.15 2001.10.13 2003.04.07 2003.04.07 2002.01.03 2004.XX.XX 2004.XX.XX

(Made in) Taiwan Taiwan Taiwan Taiwan Taiwan Taiwan Taiwan Taiwan Taiwan Taiwan Taiwan Taiwan Taiwan

For Class (A) products:

For Class (B) products:

Class (B)

212

Regulatory Information

Radio Approvals
To determine whether you are allowed to use your device in the countries listed below, please check the contains transmitter number that is printed on the identification label of your device.

Certifications radio
Pour dterminer si vous tes autoris utiliser votre dispositif dans les pays indiques ci-dessous, veuillez contrler le numro de lmetteur imprim sur ltiquette didentification de votre dispositif.

Omologazioni radio
Per determinare se sia consentito o meno utilizzare lapparecchiatura nei paesi sotto elencati, controllare il numero contiene trasmettitore impresso sulla targhetta di identificazione del dispositivo.

Funkgenehmigungen
Um festzustellen, ob Sie zum Gebrauch des Gerts in den nachfolgend aufgefhrten Lndern berechtigt sind, berprfen Sie die Transmitternummer auf dem Gerteetikett.

Permisos de utilizacin
Para determinar si puede utilizar el dispositivo en los pases que se enumeran a continuacin, compruebe el nmero contiene transmisor impreso en la etiqueta de identificacin del dispositivo.

Country Pays Paese Land Pas

Radio Transmitter Approval Reference Restrictions metteur Radio Numro du Permis Restrictions Trasmittente de Numero di Limitazioni Radio Approvazione Beschrnkungen Radio-bermittler Zustimmung-Nummer Restricciones Transmisor de Nmero de Permiso Radio PC24E-H-FC PC24E-11-FC/R CNC: 16-2327 CNC: 16-2574

Argentina

Australia

PC24E-H-FC PC24E-11-FC/R

Australia Australia

G11FNF-PC PC50E-8-FC/A A13QBF-PC For indoor use only. For indoor use only.

Australia Australia Australia Australia Australia

Alpha-1: B11FNF Alpha-1: G11FNF Alpha-1: C38WCW AP-700: AP-AG-AT-01 AP-4000: AP-AG-AT-02 For indoor use only. For indoor use only. For indoor use only.

213

Regulatory Information
Country Pays Paese Land Pas Radio Transmitter Approval Reference Restrictions metteur Radio Numro du Permis Restrictions Trasmittente de Numero di Limitazioni Radio Approvazione Beschrnkungen Radio-bermittler Zustimmung-Nummer Restricciones Transmisor de Nmero de Permiso Radio Alpha-1: A13QBF PC24E-H-FC PC24E-H-ET-L PC24E-H-ET PC24E-11-FC/R PC24E-11-ET/R CE 0336 ! Only indoor with integral or approved Range Extender Antenna. Nur zum Einsatz innerhalb von Gebuden (mit der integrierten Antenne oder einer zugelassenen Reichweitenverstrkerantenne) Only indoor with integral or approved Range Extender Antenna. Nur zum Einsatz innerhalb von Gebuden (mit der integrierten Antenne oder einer zugelassenen Reichweitenverstrkerantenne) Only indoor with integral or approved Range Extender Antenna. Nur zum Einsatz innerhalb von Gebuden (mit der integrierten Antenne oder einer zugelassenen Reichweitenverstrkerantenne). Only indoor with integral or approved Range Extender Antenna. Nur zum Einsatz innerhalb von Gebuden (mit der integrierten Antenne oder einer zugelassenen Reichweitenverstrkerantenne). CE 0122 ! R0167 SRD3a For indoor use only.

Australia Austria sterreich

Austria sterreich

G11FNF-PC G13ENE-PC

CE 0336 ! CE 0336 !

Austria sterreich

Alpha-1: B13ENE CE 0336 !

Austria sterreich

Alpha-1: G11FNF CE 0336 ! Alpha-1: G13ENE

214

Regulatory Information
Country Pays Paese Land Pas Radio Transmitter Approval Reference Restrictions metteur Radio Numro du Permis Restrictions Trasmittente de Numero di Limitazioni Radio Approvazione Beschrnkungen Radio-bermittler Zustimmung-Nummer Restricciones Transmisor de Nmero de Permiso Radio PC24E-H-FC PC24E-H-ET-L PC24E-H-ET CE 0122 ! RTT/RL/X 113 CE 0122 ! For outdoor usage you may only use channels 10 and 11 (2457 and 2462 MHz). Private usage outside buildings across less than 300 m public grounds requires no special registration. Private usage outside buildings across more than 300 m public grounds require special registration at IBPT/BIPT. Public usage outside buildings requires an IBPT/BIPT licence. For registration and license please contact IBPT/BIPT. Voor buitengebruik mag alleen kanaal 10 en 11 (2457 en 2462 MHz) worden geactiveerd. Bij prive gebruik buiten gebouwen over minder dan 300m publiek terrein is geen vergunning nodig. Voor prive gebruik buiten gebouwen over meer dan 300m publiek terrein moet een vergunning bij IBPT/BIPT aangevraagd worden. Bij publieke toepassingen buiten gebouwen moet een vergunning bij IBPT/BIPT aangevraagd worden. Pour un usage extrieur vous ne devez utiliser que les canaux 10 et 11 (2457 et 2462 MHz). Lutilisation extrieure titre priv dont la porte est infrieure 300 m de parcs publiques ne ncessite pas denregistrement. Lutilisation extrieure titre priv dont la porte est suprieure 300 m de parcs publiques ncessite lenregistrement auprs de IBPT/BIPT. Lutilisation extrieure titre publique ncessite une licence par IBPT/BIPT. Pour lenregistrement et la licence, veuillez contacter IBPT/BIPT. Fr den Einsatz im Freien sind nur die Kanle 10 und 11 (2457 und 2462 MHz) zulssig. Fr die private Nutzung auerhalb von Gebuden auf ffentlichem Gelnde und ber Entfernungen weniger als 300 m ist keine besondere Registrierung erforderlich. Fr die private Nutzung auerhalb von Gebuden auf ffentlichem Gelnde und ber Entfernungen von mehr als 300 m ist eine besondere Registrierung beim IBPT/BIPT erforderlich. Fr ffentliche Einzatz ist eine besondere Registrierung beim IBPT/BIPT erforderlich. Only indoor with integral or approved Range Extender Antenna. Alleen voor gebruik binnenshuis met ingebouwde of goedgekeurde reikwijdteversterkerantenne. Pour usage intrieur uniquement, avec une antenne intgrale ou amplificatrice approuve.

Belgium Belgie Belgique

PC24E-11-FC/R PC24E-11-ET/R

CE 0336 ! CE 0336 !

215

Regulatory Information
Country Pays Paese Land Pas Radio Transmitter Approval Reference Restrictions metteur Radio Numro du Permis Restrictions Trasmittente de Numero di Limitazioni Radio Approvazione Beschrnkungen Radio-bermittler Zustimmung-Nummer Restricciones Transmisor de Nmero de Permiso Radio Alpha-1: C38WCW CE 0560 ! Only indoor with integral or approved Range Extender Antenna. Alleen voor gebruik binnenshuis met ingebouwde of goedgekeurde reikwijdteversterkerantenne. Pour usage intrieur uniquement, avec une antenne intgrale ou amplificatrice approuve. Nur zum Einsatz innerhalb von Gebuden (mit der integrierten Antenne oder einer zugelassenen Reichweitenverstrkerantenne). Only indoor with integral or approved Range Extender Antenna. Alleen voor gebruik binnenshuis met ingebouwde of goedgekeurde reikwijdteversterkerantenne. Pour usage intrieur uniquement, avec une antenne intgrale ou amplificatrice approuve. Nur zum Einsatz innerhalb von Gebuden (mit der integrierten Antenne oder einer zugelassenen Reichweitenverstrkerantenne). Only indoor with integral or approved Range Extender Antenna. Alleen voor gebruik binnenshuis met ingebouwde of goedgekeurde reikwijdteversterkerantenne. Pour usage intrieur uniquement, avec une antenne intgrale ou amplificatrice approuve. Nur zum Einsatz innerhalb von Gebuden (mit der integrierten Antenne oder einer zugelassenen Reichweitenverstrkerantenne).

Belgium

Belgium Belgium

AP-700: AP-AG-AT-01 AP-4000: AP-AG-AT-02

CE 0560 ! CE 0560 !

Belgium Belgie Belgique

G11FNF-PC G13ENE-PC

CE 0336 ! CE 0336 !

Belgium Belgie Belgique

PC50E-4-ET/A PC50E-8-ET/A A19PCE-PC

CE 0336 ! CE 0336 ! CE 0560 ! Only indoor with integral or approved Range Extender Antenna. Alleen voor gebruik binnenshuis met ingebouwde of goedgekeurde reikwijdteversterkerantenne. Pour usage intrieur uniquement, avec une antenne intgrale ou amplificatrice approuve. Nur zum Einsatz innerhalb von Gebuden (mit der integrierten Antenne oder einer zugelassenen Reichweitenverstrkerantenne). Only indoor with integral or approved Range Extender Antenna. Alleen voor gebruik binnenshuis met ingebouwde of goedgekeurde reikwijdteversterkerantenne. Pour usage intrieur uniquement, avec une antenne intgrale ou amplificatrice approuve. Nur zum Einsatz innerhalb von Gebuden (mit der integrierten Antenne oder einer zugelassenen Reichweitenverstrkerantenne).

Belgium Belgie Belgique

Alpha-1: B13ENE CE 0336 !

Belgium Belgie Belgique

Alpha-1: G11FNF CE 0336 ! Alpha-1: G13ENE CE 0336 !

216

Regulatory Information
Country Pays Paese Land Pas Radio Transmitter Approval Reference Restrictions metteur Radio Numro du Permis Restrictions Trasmittente de Numero di Limitazioni Radio Approvazione Beschrnkungen Radio-bermittler Zustimmung-Nummer Restricciones Transmisor de Nmero de Permiso Radio Alpha-1: A04LAE Alpha-1:A08NAE PC24E-H-FC CE 0336 ! CE 0336 !

Belgium Belgie Belgique Brazil

This equipment operates in secondary mode: It is not allowed to protect the equipment against harmful modelo: (01) 07898903006 02 0 interference from primary mode stations or stations of the PC24E-11-FC/R same type. It is not allowed to cause interference to Fabricante: Agere systems that operate in primary mode. Systems Netherlands B.V. G11FNF-PC pending This equipment operates in secondary mode: It is not allowed to protect the equipment against harmful interference from primary mode stations or stations of the same type. It is not allowed to cause interference to systems that operate in primary mode.

Brazil

Brazil

Alpha-1, modelo: (01) 07898903006 01 3 This equipment operates in secondary mode: It is not B11FNF allowed to protect the equipment against harmful Fabricante: Proxim interference from primary mode stations or stations of the Corporation p/a same type. It is not allowed to cause interference to Europe B.V. systems that operate in primary mode. Alpha-1: G11FNF pending This equipment operates in secondary mode: It is not allowed to protect the equipment against harmful interference from primary mode stations or stations of the same type. It is not allowed to cause interference to systems that operate in primary mode. System with outdoor antenna requires license from Industry Canada. Les systmes dots dune antenne extrieure ncessitent la dlivrance dune licence de la part de Industry Canada.

Brazil

Canada

PC24E-H-FC PC24-11-FC/R

IC: 230391152A IC: 4005A-PC2411R

PC24E-11-FC/R Canada G11FNF-PC

IIC: 4005104679A IC: 1856A-G11FNFPC System with outdoor antenna requires license from Industry Canada. Les systmes dots dune antenne extrieure ncessitent la dlivrance dune licence de la part de Industry Canada. IC: 1856A-C38WCW For indoor use only. Pour usage intrieur uniquement.

Canada

C38WCW

Canada Canada Canada

AP-700: AP-AG-AT-01 AP-4000: AP-AG-AT-02 PC50E-8-FC/A A13QBF-PC

IC: 4110A-APAGAT01 For indoor use only. Pour usage intrieur uniquement. IC: 4110A-APAGAT02 IC: 4005A-PCE508A IC: 1856A-A13QBFPC For indoor use only. Pour usage intrieur uniquement.

217

Regulatory Information
Country Pays Paese Land Pas Radio Transmitter Approval Reference Restrictions metteur Radio Numro du Permis Restrictions Trasmittente de Numero di Limitazioni Radio Approvazione Beschrnkungen Radio-bermittler Zustimmung-Nummer Restricciones Transmisor de Nmero de Permiso Radio Alpha-1: B11FNF IC: 1856B-B11FNF Only with integral, approved Range Extender Antenna. Pour usage avec une antenne intgrale ou amplificatrice approuve. Only with integral, approved Range Extender Antenna. Pour usage avec une antenne intgrale ou amplificatrice approuve. For indoor use only. Pour usage intrieur uniquement.

Canada

Canada

Alpha-1: G11FNF IC: 1856A-G11FNF

Canada

Alpha-1: A13QBF IC: 1856A-A13QBF

China

PC24E-H-FC PC24E-H-ET PC24E-11-FC/R PC24E-11-ET/R

CMII: 2001AJ0385 CMII: 2000AJ0152 CMII ID: 2002DJ1380 CMII ID: 2002DJ1225 CMII ID: 2003DJ0807 CMII ID: 2003AJ0806 The use of external antennas is not allowed The use of external antennas is not allowed

China China China

G13ENE-PC A04VBA-PC

Alpha-1: B13ENE CMII ID: 2003DJ0344 MPCI3A-20/R Agere Systems Alpha-1: G13ENE CMII ID: 2003DJ0604 Alpha-1: A04VBA CMII ID: 2003AP0741

China China China China China Chile

The use of external antennas is not allowed

Alpha-1: C38WCW CMII ID: 2003DJ1055 AP-700: AP-AG-AT-01 AP-4000: AP-AG-AT-02 PC24E-H-FC PC24E-11-FC/R CMII ID: pending CMII ID: pending

The use of external antennas is not allowed The use of external antennas is not allowed

Chile

G11FNF-PC G13ENE-PC

SUBTEL 34166 SUBTEL 34166

Colombia

PC24E-H-FC PC24E-11-FC/R 400399

Colombia Colombia Colombia

G11FNF-PC Alpha-1: B11FNF Alpha-1: G11FNF

218

Regulatory Information
Country Pays Paese Land Pas Radio Transmitter Approval Reference Restrictions metteur Radio Numro du Permis Restrictions Trasmittente de Numero di Limitazioni Radio Approvazione Beschrnkungen Radio-bermittler Zustimmung-Nummer Restricciones Transmisor de Nmero de Permiso Radio PC24E-H-ET-L PC24E-H-ET Denmark Danmark PC24E-H-FC PC24E-H-ET-L PC24E-H-ET PC24E-11-FC/R PC24E-11-ET/R CE 0122 ! R0167 SRD3a CE 0122 ! CE 0336 ! CE 0336 ! Only indoor with integral or approved Range Extender Antenna. Kun til indendrs brug sammen med en integreret eller godkendt afstandsforlngerantenne. Only indoor with integral or approved Range Extender Antenna. Kun til indendrs brug sammen med en integreret eller godkendt afstandsforlngerantenne. For indoor use only. Nemlig til indendrs brug. 45314454

Czech Republic

Denmark Danmark

G11FNF-PC G13ENE-PC

CE 0336 ! CE 0336 !

Denmark Danmark

PC50E-4-ET/A

CE 0336 !

A19PCE-PC Denmark Danmark

CE 0560 ! Only indoor with integral or approved Range Extender Antenna. Kun til indendrs brug sammen med en integreret eller godkendt afstandsforlngerantenne. Use only with approved external antennas.

Alpha-1: B13ENE CE 0336 !

Denmark Danmark

Alpha-1: G11FNF CE 0336 ! Alpha-1: G13ENE CE 0336 !

Denmark

Alpha-1: C38WCW CE 0560 !

Only indoor with integral or approved Range Extender Antenna Kun til indendrs brug sammen med en integreret eller godkendt afstandsforlngerantenne. Only indoor with integral or approved Range Extender Antenna Kun til indendrs brug sammen med en integreret eller godkendt afstandsforlngerantenne. For indoor use only. Nemlig til indendrs brug.

Denmark Denmark Denmark Danmark Estonia

AP-700: AP-AG-AT-01 AP-4000: AP-AG-AT-02 Alpha-1: A04LAE

CE 0560 ! CE 0560 ! CE 0336 !

PC24E-H-ET-L PC24E-H-ET

M9599048

219

Regulatory Information
Country Pays Paese Land Pas Radio Transmitter Approval Reference Restrictions metteur Radio Numro du Permis Restrictions Trasmittente de Numero di Limitazioni Radio Approvazione Beschrnkungen Radio-bermittler Zustimmung-Nummer Restricciones Transmisor de Nmero de Permiso Radio PC24E-H-FC PC24E-H-ET-L PC24E-H-ET PC24E-11-FC/R PC24E-11-ET/R CE 0336 ! Only indoor with integral or approved Range Extender Antenna. Ainoa sis- avulla integraali eli hyvksytty Ala Avartaa Tuntosarvi. Only indoor with integral or approved Range Extender Antenna. Ainoa sis- avulla integraali eli hyvksytty Ala Avartaa Tuntosarvi. For indoor use only. Ajaksi sis- apu ainoa CE 0122 ! R0167 SRD3a

Finland Suomi

Finland Suomi

G11FNF-PC G13ENE-PC

CE 0336 ! CE 0336 !

Finland Suomi

PC50E-4-ET/A PC50E-8-ET/A A19PCE-PC

CE 0336 ! CE 0336 ! CE 0560 !

Finland Suomi

Alpha-1: B13ENE CE 0336 !

Only indoor with integral or approved Range Extender Antenna. Ainoa sis- avulla integraali eli hyvksytty Ala Avartaa Tuntosarvi. Only indoor with integral or approved Range Extender Antenna. Ainoa sis- avulla integraali eli hyvksytty Ala Avartaa Tuntosarvi. Only indoor with integral or approved Range Extender Antenna. Ainoa sis- avulla integraali eli hyvksytty Ala Avartaa Tuntosarvi. Only indoor with integral or approved Range Extender Antenna. Ainoa sis- avulla integraali eli hyvksytty Ala Avartaa Tuntosarvi. For indoor use only. Ajaksi sis- apu ainoa.

Finland Suomi

Alpha-1: G11FNF CE 0336 ! Alpha-1: G13ENE CE 0336 !

Finland Suomi

Alpha-1: C38WCW CE 0560 !

Finland Suomi Finland Suomi Finland Suomi

AP-700: AP-AT-AG-01 AP-4000: AP-AT-AG-02 Alpha-1: A04LAE Alpha-1:A08NAE

CE 0560 ! CE 0560 ! CE 0336 ! CE 0336 !

220

Regulatory Information
Country Pays Paese Land Pas Radio Transmitter Approval Reference Restrictions metteur Radio Numro du Permis Restrictions Trasmittente de Numero di Limitazioni Radio Approvazione Beschrnkungen Radio-bermittler Zustimmung-Nummer Restricciones Transmisor de Nmero de Permiso Radio PC24E-H-FC CE 0122 ! Restricted frequency band: On French territory PC24E-H-FC devices may only use channels 10 and 11 (2457 and 2462 MHz). Bande de frquence limite : Sur le territoire franais les dispositifs PC24E-H-FC ne sont autoriss utiliser que les canaux 10 et 11 (2457 MHz et 2462 MHz). PC24E-H-FR(-L) & PC24E-H-ET(-L) devices may only use channels 10, 11,12 and 13 (2457, 2462, 2467and 2472 MHz). It is not allowed to operate the device at any other channel as supported by the device. License required for every indoor installation (please contact ART for procedure to follow). Use outdoors is not allowed. Les dispositifs PC24E-H-FR(-L) & PC24E-H-ET(-L) ne sont autoriss utiliser que les canaux 10, 11,12 et 13 (2457, 2462, 2467et 2472 MHz). Il est interdit dutiliser le dispositif sur les autres canaux pris en charge par le dispositif. La licence est requise pour toute installation intrieure (veuillez contacter ART pour les procdures suivre). Les installations extrieures sont interdites. Only indoor with integral or approved Range Extender Antenna. Pour usage intrieur uniquement, avec une antenne intgrale ou amplificatrice approuve. Only indoor with integral or approved Range Extender Antenna. Pour usage intrieur uniquement, avec une antenne intgrale ou amplificatrice approuve. Only indoor with integral or approved Range Extender Antenna. Pour usage intrieur uniquement, avec une antenne intgrale ou amplificatrice approuve. Only indoor with integral or approved Range Extender Antenna. Pour usage intrieur uniquement, avec une antenne intgrale ou amplificatrice approuve. For indoor use only. Pour usage intrieur uniquement.

France

PC24E-H-FR-L PC24E-H-FR

99 0394 PP 0 (Dossier 97289 RD) 99 0393 PP 0 (Dossier 97290 RD)

PC24E-11-FC/R PC24E-11-ET/R PC24E-11-FR/R France G11FNF-PC G13ENE-PC

CE 0336 ! CE 0336 ! CE 0336 ! CE 0336 ! CE 0336 !

France

Alpha-1: C38WCW CE 0560 !

France France France

AP-700: AP-AG-AT-01 AP-4000: AP-AG-AT-02 PC50E-4-ET/A PC50E-4-ET/B PC50E-4-ET/C A19PCE-PC

CE 0560 ! CE 0560 ! CE 0336 ! CE 0336 ! CE 0336 ! CE 0560 !

221

Regulatory Information
Country Pays Paese Land Pas Radio Transmitter Approval Reference Restrictions metteur Radio Numro du Permis Restrictions Trasmittente de Numero di Limitazioni Radio Approvazione Beschrnkungen Radio-bermittler Zustimmung-Nummer Restricciones Transmisor de Nmero de Permiso Radio Alpha-1: B13ENE CE 0336 ! Restricted frequency band: On French territory B13ENE devices may only use channels 10, 11, 12, and 13 (2457, 2462, 2467 and 2472 MHz). For WLAN hotspots, ART (Autorit de Regulation des Tlcommunications) has special regulations allowing the use of other channels as well; check with ART for authorizations and local rulings. Only indoor with integral or approved Range Extender Antenna. Bande de frquence limite : Sur le territoire franais les dispositifs B13ENE / G13ENE ne sont autoriss utiliser que les canaux 10, 11, 12 et 13 (2457, 2462, 2467 et 2472 MHz). Pour les rseaux locaux sans fil (WLAN), lAutorit de Regulation des Tlcommunications (ART) permet l'utilisation d'autres bandes de frquence; vrifiez auprs de l'ART pour les autorisations et rglments locaux. Pour usage intrieur uniquement, avec une antenne intgrale ou amplificatrice approuve. Restricted frequency band: On French territory B13ENE devices may only use channels 10, 11, 12, and 13 (2457, 2462, 2467 and 2472 MHz). For WLAN hotspots, ART (Autorit de Regulation des Tlcommunications) has special regulations allowing the use of other channels as well; check with ART for authorizations and local rulings. Only indoor with integral or approved Range Extender Antenna. Bande de frquence limite : Sur le territoire franais les dispositifs B13ENE / G13ENE ne sont autoriss utiliser que les canaux 10, 11, 12 et 13 (2457, 2462, 2467 et 2472 MHz). Pour les rseaux locaux sans fil (WLAN), lAutorit de Regulation des Tlcommunications (ART) permet l'utilisation d'autres bandes de frquence; vrifiez auprs de l'ART pour les autorisations et rglments locaux. Pour usage intrieur uniquement, avec une antenne intgrale ou amplificatrice approuve. CE 0336 ! For indoor use only. Pour usage intrieur uniquement.

France

France

Alpha-1: G11FNF Alpha-1: G13ENE

France

Alpha-1: A04LAE

Germany PC24E-H-FC Deutschland PC24E-H-ET-L PC24E-H-ET PC24E-11-FC/R PC24E-11-ET/R

License required for outdoor installations. Check with reseller for procedure to follow. CETECOM: D810070L Fr Installationen im Freien ist eine Lizenz erforderlich. Nhere Informationen zur Vorgehensweise erhalten Sie bei CETECOM: D810069L Ihrem Hndler. CE 0336 ! CE 0336 ! Only indoor with integral or approved Range Extender Antenna. Nur zum Einsatz innerhalb von Gebuden (mit der integrierten Antenne oder einer zugelassenen Reichweitenverstrkerantenne)

CE 0122 !

222

Regulatory Information
Country Pays Paese Land Pas Radio Transmitter Approval Reference Restrictions metteur Radio Numro du Permis Restrictions Trasmittente de Numero di Limitazioni Radio Approvazione Beschrnkungen Radio-bermittler Zustimmung-Nummer Restricciones Transmisor de Nmero de Permiso Radio CE 0336 ! CE 0336 ! Only indoor with integral or approved Range Extender Antenna. Nur zum Einsatz innerhalb von Gebuden (mit der integrierten Antenne oder einer zugelassenen Reichweitenverstrkerantenne) Only indoor with integral or approved Range Extender Antenna. Nur zum Einsatz innerhalb von Gebuden (mit der integrierten Antenne oder einer zugelassenen Reichweitenverstrkerantenne) Only indoor with integral or approved Range Extender Antenna. Nur zum Einsatz innerhalb von Gebuden (mit der integrierten Antenne oder einer zugelassenen Reichweitenverstrkerantenne) For indoor use only. Nur fr Innengebrauch.

Germany G11FNF-PC Deutschland G13ENE-PC

Germany Alpha-1: C38CWC CE 0560 ! Deutschland

AP-700: AP-AG-AT-01 AP-4000: AP-AG-AT-02 Germany PC50E-4-ET/A Deutschland PC50E-8-ET/A A19PCE-PC

CE 0560 ! CE 0560 !

CE 0336 ! CE 0336 ! CE 0560 !

Germany Alpha-1: B13ENE CE 0336 ! Deutschland

Only indoor with integral or approved Range Extender Antenna. Nur zum Einsatz innerhalb von Gebuden (mit der integrierten Antenne oder einer zugelassenen Reichweitenverstrkerantenne) Only indoor with integral or approved Range Extender Antenna. Nur zum Einsatz innerhalb von Gebuden (mit der integrierten Antenne oder einer zugelassenen Reichweitenverstrkerantenne) For indoor use only. Fr nur Innengebrauch.

Germany Alpha-1: G11FNF CE 0336 ! Deutschland Alpha-1: G13ENE CE 0336 !

Germany Alpha-1: A04LAE CE 0336 ! Deutschland Alpha-1: A08NAE CE 0336 ! Greece PC24E-H-FC PC24E-11-FC/R PC24E-11-ET/R Greece G11FNF-PC G13ENE-PC Greece CE 0122 ! CE 0336 ! CE 0336 ! CE 0336 ! CE 0336 !

Only indoor with integral or approved Range Extender Antenna. Only indoor with integral or approved Range Extender Antenna. Only indoor with integral or approved Range Extender Antenna. Only indoor with integral or approved Range Extender Antenna. .

Alpha-1: B13ENE CE 0336 !

Greece

Alpha-1: G11FNF CE 0336 ! Alpha-1: G13ENE CE 0336 !

223

Regulatory Information
Country Pays Paese Land Pas Radio Transmitter Approval Reference Restrictions metteur Radio Numro du Permis Restrictions Trasmittente de Numero di Limitazioni Radio Approvazione Beschrnkungen Radio-bermittler Zustimmung-Nummer Restricciones Transmisor de Nmero de Permiso Radio PC24E-H-FC PC24E-H-ET PC24E-11-FC/R Hong Kong Hong Kong Hong Kong Hong Kong Hong Kong Hong Kong Hong Kong Hong Kong Hungary Alpha-1: B13ENE HKTA-1039 Alpha-1: A09SBS G13ENE-PC A19PCE-PC HKTA-1039 HKTA-1039 HKTA-1039 LP400096 LP400095

Hong Kong

Alpha-1: G13ENE HKTA-1039 Alpha-1: C38WCW HKTA-1039 AP-700: AP-AT-AG-01 AP-4000: AP-AT-AG-02 PC24E-H-FC PC24E-H-ET-L PC24E-H-ET HKTA-1039 HKTA-1039 LA-004-1-2000/00 LA-005-0-2000/00 LA-004-0-2000/00 CE 0122 ! R0167 SRD3a

Iceland sland

PC24E-H-FC PC24E-H-ET-L PC24E-H-ET PC24E-11-FC/R PC24E-11-ET/R

CE 0336 ! CE 0336 ! CE 0336! CE 0336!

Only indoor with integral or approved Range Extender Antenna. Only indoor with integral or approved Range Extender Antenna. Only indoor with integral or approved Range Extender Antenna. Only indoor with integral or approved Range Extender Antenna.

Iceland sland

G11FNF-PC G13ENE-PC

Iceland sland Iceland sland Iceland sland

Alpha-1: C38WCW CE 0560!

AP-700: AP-AG-AT-01 AP-4000: AP-AG-AT-02

CE 0560! CE 0560!

224

Regulatory Information
Country Pays Paese Land Pas Radio Transmitter Approval Reference Restrictions metteur Radio Numro du Permis Restrictions Trasmittente de Numero di Limitazioni Radio Approvazione Beschrnkungen Radio-bermittler Zustimmung-Nummer Restricciones Transmisor de Nmero de Permiso Radio PC50E-4-ET/A PC50E-8-ET/A A19PCE-PC Iceland sland Iceland sland CE 0336 ! CE 0336! CE 0560 ! Only indoor with integral or approved Range Extender Antenna. Only indoor with integral or approved Range Extender Antenna. For indoor use only. Fyrir inni- nota eini India Telegraph Act 1885 requires End User License. To obtain a license contact: The Jt. Wireless Advisor The Wireless Planning & Co-ordination Wing Ministry of Communications, Sanchar Bhavan New Delhi CE 0122 ! TRA 24/5/84/6 CE 0122 ! CE 0336 ! CE 0336 ! CE 0336 ! CE 0336 ! Only indoor with integral or approved Range Extender Antenna. Only indoor with integral or approved Range Extender Antenna. Restricted frequency band: only channels 4 through 8 (2418.0-2457.0 MHz) may be used in Israel. Restricted frequency band: only channels 4 through 8 (2418.0-2457.0 MHz) may be used in Israel. Only indoor with integral or approved Range Extender Antenna. Only indoor with integral or approved Range Extender Antenna. Only indoor with integral or approved Range Extender Antenna. For indoor use only. Fyrir inni- nota eini

Iceland sland

Alpha-1: B13ENE CE 0336 !

Alpha-1: G11FNF CE 0336 ! Alpha-1: G13ENE CE 0336 !

Iceland sland

Alpha-1: A04LAE

CE 0336 !

Alpha-1: A08NAE CE 0336 ! India PC24E-H-FC PC24E-11-FC/R

Ireland

PC24E-H-FC PC24E-H-ET-L PC24E-H-ET PC24E-11-FC/R PC24E-11-ET/R

Ireland

G11FNF-PC G13ENE-PC

Ireland

Alpha-1: B13ENE CE 0336 !

Ireland

Alpha-1: G11FNF CE 0336 ! Alpha-1: G13ENE CE 0336 !

Israel

PC24E-11-IL/R

MoC 597-2002

225

Regulatory Information
Country Pays Paese Land Pas Radio Transmitter Approval Reference Restrictions metteur Radio Numro du Permis Restrictions Trasmittente de Numero di Limitazioni Radio Approvazione Beschrnkungen Radio-bermittler Zustimmung-Nummer Restricciones Transmisor de Nmero de Permiso Radio G05INI-PC MoC pending Restricted frequency band: only channels 4 through 8 (2418.0-2457.0 MHz) may be used in Israel. Restricted frequency band: only channels 4 through 8 (2418.0-2457.0 MHz) may be used in Israel. Only indoor with integral or approved Range Extender Antenna. Only indoor with integral or approved Range Extender Antenna. Restricted frequency band: only channels 4 through 8 (2418.0-2457.0 MHz) may be used in Israel. Restricted frequency band: only channels 4 through 8 (2418.0-2457.0 MHz) may be used in Israel. Only indoor with integral or approved Range Extender Antenna.

Israel

Israel

Alpha-1: B05INI

MoC pending

Israel

Alpha-1: G05INI

MoC pending

Italy Italia

PC24E-H-FC PC24E-H-ET-L

License required for indoor use. Use with outdoor installations not allowed. CEPT-RLAN I Licenza necessaria per uso in interno. Non consentito DGPGF/4/2/144-03/340 luso in installazioni esterne 367/96 CEPT-RLAN I DGPGF/4/2/144-03/340 327/774 CE 0336 ! CE 0336 ! Only indoor with integral or approved Range Extender Antenna. Solo per interni con Antenna Range Extender integrale o approvata. Only indoor with integral or approved Range Extender Antenna. Solo per interni con Antenna Range Extender integrale o approvata. Only indoor with integral or approved Range Extender Antenna. Solo per interni con Antenna Range Extender integrale o approvata. Only indoor with integral or approved Range Extender Antenna. Solo per interni con Antenna Range Extender integrale o approvata.

CE 0122 !

PC24E-H-ET

PC24E-11-FC/R PC24E-11-ET/R

Italy Italia

G11FNF-PC G13ENE-PC

CE 0336 ! CE 0336 !

Italy Italia

Alpha-1: B13ENE CE 0336 !

Italy Italia

Alpha-1: G11FNF CE 0336 ! Alpha-1: G13ENE CE 0336 !

226

Regulatory Information
Country Pays Paese Land Pas Radio Transmitter Approval Reference Restrictions metteur Radio Numro du Permis Restrictions Trasmittente de Numero di Limitazioni Radio Approvazione Beschrnkungen Radio-bermittler Zustimmung-Nummer Restricciones Transmisor de Nmero de Permiso Radio PC24E-H-FC PC24E-H-JP PC24E-H-ET-L PC24E-11-FC/R PC24E-11-JP/R Japan Japan G13GNJ-PC PC50E-4-JP/A A04LEJ-PC Japan Alpha-1: B14GNJ TELEC: NYCA0010 TELEC: NYCA0008 TELEC: GZCA0007 TELEC: NYCA00024 TELEC: 01NYDA1121 JATE: D01-1128JP TELEC: 01NYDA1122 TELEC: 03YNDA0185 TELEC: 03GZDA0150 TELEC: 01WYBA1051 For indoor use only. TELEC: 03WYBA0048 TELEC: 03NYDA0130 Only indoor with integral or approved Range Extender TELEC: 03GZDA0079 Antenna. ( ) JATE: D99-1057JP

Japan

Japan

Alpha-1: G13GNJ TELEC: 03YNDA0190 Only indoor with integral or approved Range Extender TELEC: 03GZDA0154 Antenna. ( ) Alpha-1: A04LEJ TELEC: 03WYBA0025 For indoor use only.

Japan Japan

Alpha-1: C38WCW TELEC: 003NY03042 Only indoor with integral or approved Range Extender 0000 Antenna. TELEC: 003GZ03027 0000 TELEC: 003WY03015 ( ) 0000 AP-700: AP-AG-AT-01 AP-4000: AP-AG-AT-02 PC24E-H-FC TELEC: pending TELEC: pending TELEC: pending TELEC: pending TELEC: pending TELEC: pending MIC: R-LARN-01-028 Certification date: 2002.10.15 MIC: R-LARN-02-0027 Certification date: 2002.01.26 MIC: R-LARN-03-0238 Product name: PC Card Certification date: Manufacturer: Proxim Corporation 2003.05.29 Made in: Taiwan
Only indoor with integral or approved Range Extender Antenna.

Japan Japan Korea

( )

Product name: PC Card Manufacturer: Agere Systems Made in: Taiwan

PC24E-11-FC/R

Korea

G11FNF-PC

227

Regulatory Information
Country Pays Paese Land Pas Radio Transmitter Approval Reference Restrictions metteur Radio Numro du Permis Restrictions Trasmittente de Numero di Limitazioni Radio Approvazione Beschrnkungen Radio-bermittler Zustimmung-Nummer Restricciones Transmisor de Nmero de Permiso Radio A04VBA-PC MIC: R-LARN-03-0248 Product name: PC Card Certification date: Manufacturer: Proxim Corporation 2003.06-04 Made in: Taiwan

Korea

Korea

Alpha-1: B13ENE MIC: R-LARN-03-0209 Product name: PC Card Certification date: Manufacturer: Proxim Corporation 2003.05.13 Made in: Taiwan Alpha-1: G11FNF MIC: R-LARN-03-0230 Product name: PC Card Certification date: Manufacturer: Proxim Corporation 2003.05.23 Made in: Taiwan Alpha-1: C38WCW MIC: R-LARN-03-0366 Product name: PC Card Certification date: Manufacturer: Proxim Corporation 2003.08.29 Made in: Taiwan AP-700: AP-AG-AT-01 AP-4000: AP-AG-AT-02 Alpha-1: A04VBA MIC: pending Certification date: 2004.XX.XX MIC: pending Certification date: 2004.XX.XX MIC: R-LARN-03-208 Certification date: 2003.05.13 CE 0122 ! R&TTE Directive 1999/5/EC CE 0336 ! Only indoor with integral or approved Range Extender Antenna. Nur zum Einsatz innerhalb von Gebuden (mit der integrierten Antenne oder einer zugelassenen Reichweitenverstrkerantenne) Only indoor with integral or approved Range Extender Antenna. Nur zum Einsatz innerhalb von Gebuden (mit der integrierten Antenne oder einer zugelassenen Reichweitenverstrkerantenne) For indoor use only. Nur fr Innengebrauch. Only indoor with integral or approved Range Extender Antenna. Nur zum Einsatz innerhalb von Gebuden (mit der integrierten Antenne oder einer zugelassenen Reichweitenverstrkerantenne) Product name: PC Card Manufacturer: Proxim Corporation Made in: Taiwan Product name: Access Point Manufacturer: Proxim Corporation Made in: Taiwan

Korea

Korea

Korea

Korea

Korea

Liechtenstein PC24E-H-FC

PC24E-11-FC/R PC24E-11-ET/R

Liechtenstein G11FNF-PC G13ENE-PC

CE 0336! CE 0336!

Liechtenstein PC50E-4-ET/A A19PCE-PC

CE 0336 ! CE 0560 !

Liechtenstein Alpha-1: C38WCW CE 0560!

228

Regulatory Information
Country Pays Paese Land Pas Radio Transmitter Approval Reference Restrictions metteur Radio Numro du Permis Restrictions Trasmittente de Numero di Limitazioni Radio Approvazione Beschrnkungen Radio-bermittler Zustimmung-Nummer Restricciones Transmisor de Nmero de Permiso Radio CE 0560! CE 0560! Only indoor with integral or approved Range Extender Antenna. Nur zum Einsatz innerhalb von Gebuden (mit der integrierten Antenne oder einer zugelassenen Reichweitenverstrkerantenne) Only indoor with integral or approved Range Extender Antenna. Nur zum Einsatz innerhalb von Gebuden (mit der integrierten Antenne oder einer zugelassenen Reichweitenverstrkerantenne) Only indoor with integral or approved Range Extender Antenna. Nur zum Einsatz innerhalb von Gebuden (mit der integrierten Antenne oder einer zugelassenen Reichweitenverstrkerantenne) For indoor use only. Fr nur Innengebrauch.

Liechtenstein AP-700: AP-AG-AT-01 Liechtenstein AP-4000: AP-AG-AT-02

Liechtenstein Alpha-1: B13ENE CE 0336 !

Liechtenstein Alpha-1: G11FNF CE 0336 ! Alpha-1: G13ENE CE 0336 !

Liechtenstein Alpha-1: A04LAE

CE 0336 !

Lithuania

PC24E-H-FC PC24E-H-ET-L PC24E-H-ET

14E911 Nr. 0225 14E911 Nr. 0225

Luxemburg PC24E-H-FC Luxembourg PC24E-H-ET-L PC24E-H-ET PC24E-11-FC/R PC24E-11-ET/R

CE 0122 ! L 2490/10585-01J L 2490/10584-01J CE 0336 ! CE 0336 ! Only indoor with integral or approved Range Extender Antenna. Pour usage intrieur uniquement, avec une antenne intgrale ou amplificatrice approuve. Only indoor with integral or approved Range Extender Antenna. Pour usage intrieur uniquement, avec une antenne intgrale ou amplificatrice approuve. Only indoor with integral or approved Range Extender Antenna. Pour usage intrieur uniquement, avec une antenne intgrale ou amplificatrice approuve. Only indoor with integral or approved Range Extender Antenna. Pour usage intrieur uniquement, avec une antenne intgrale ou amplificatrice approuve.

Luxemburg G11FNF-PC Luxembourg

CE 0336 !

Luxemburg Alpha-1: C38WCW CE 0560 ! Luxembourg

Luxemburg AP-700: Luxembourg AP-AG-AT-01 Luxemburg AP-4000: Luxembourg AP-AG-AT-02

CE 0560 ! CE 0560 !

229

Regulatory Information
Country Pays Paese Land Pas Radio Transmitter Approval Reference Restrictions metteur Radio Numro du Permis Restrictions Trasmittente de Numero di Limitazioni Radio Approvazione Beschrnkungen Radio-bermittler Zustimmung-Nummer Restricciones Transmisor de Nmero de Permiso Radio CE 0336 ! CE 0336 ! CE 0560 ! Only indoor with integral or approved Range Extender Antenna. Pour usage intrieur uniquement, avec une antenne intgrale ou amplificatrice approuve. Only indoor with integral or approved Range Extender Antenna. Pour usage intrieur uniquement, avec une antenne intgrale ou amplificatrice approuve. For indoor use only. Pour usage intrieur uniquement. On Mexican territory wireless devices may only use channel 11 (2450.0-2483.5 MHz), however for indoors use there are no restrictions on for using all channels, because use of this equipment in Mexico is on secundary basis. En el territorio mexicano, los dispositivos inalmbricos slo pueden usar el canal 11 (2450,0-2483,5 MHz), pero no hay restriccion para el uso de estos equipos dentro de areas cerradas porque operan con frequencia de uso secundario. Para uso en areas abiertas, la banda de frequencia esta restringida. On Mexican territory wireless devices may only use channel 11 (2450.0-2483.5 MHz), however for indoors use there are no restrictions on for using all channels, because use of this equipment in Mexico is on secundary basis. En el territorio mexicano, los dispositivos inalmbricos slo pueden usar el canal 11 (2450,0-2483,5 MHz), pero no hay restriccion para el uso de estos equipos dentro de areas cerradas porque operan con frequencia de uso secundario. Para uso en areas abiertas, la banda de frequencia esta restringida. For indoor use only. Para el uso interior slo. For indoor use only. Pour usage intrieur uniquement.

Luxemburg PC50E-4-ET/A Luxembourg PC50E-8-ET/A A19PCE-PC

Luxemburg Alpha-1: B13ENE CE 0336 ! Luxembourg

Luxemburg Alpha-1: G11FNF CE 0336 ! Luxembourg Alpha-1: G13ENE CE 0336 !

Luxemburg Alpha-1: A04LAE CE 0336 ! Luxembourg Alpha-1: A08NAE CE 0336 ! Mexico Mxico PC-24E-H-FC PC24E-11-FC/R COFETEL: RCPLUWA99-660 COFETEL: RCPLUPC01-498-A2

Mexico Mxico

G11FNF-PC

COFETEL: RCPPRG103-249

Mexico Mxico

PC50E-8-FC/A A13QBF-PC

COFETEL: RTIPRPC02-369 COFETEL: RTIPRA103-310

230

Regulatory Information
Country Pays Paese Land Pas Radio Transmitter Approval Reference Restrictions metteur Radio Numro du Permis Restrictions Trasmittente de Numero di Limitazioni Radio Approvazione Beschrnkungen Radio-bermittler Zustimmung-Nummer Restricciones Transmisor de Nmero de Permiso Radio Alpha-1: B11FNF COFETEL: PCPPRAL03-095 On Mexican territory wireless devices may only use channel 11 (2450.0-2483.5 MHz), however for indoors use there are no restrictions on for using all channels, because use of this equipment in Mexico is on secundary basis. En el territorio mexicano, los dispositivos inalmbricos slo pueden usar el canal 11 (2450,0-2483,5 MHz), pero no hay restriccion para el uso de estos equipos dentro de areas cerradas porque operan con frequencia de uso secundario. Para uso en areas abiertas, la banda de frequencia esta restringida. On Mexican territory wireless devices may only use channel 11 (2450.0-2483.5 MHz), however for indoors use there are no restrictions on for using all channels, because use of this equipment in Mexico is on secundary basis. En el territorio mexicano, los dispositivos inalmbricos slo pueden usar el canal 11 (2450,0-2483,5 MHz), pero no hay restriccion para el uso de estos equipos dentro de areas cerradas porque operan con frequencia de uso secundario. Para uso en areas abiertas, la banda de frequencia esta restringida. On Mexican territory wireless devices may only use channel 11 (2450.0-2483.5 MHz), however for indoors use there are no restrictions on for using all channels, because use of this equipment in Mexico is on secundary basis. En el territorio mexicano, los dispositivos inalmbricos slo pueden usar el canal 11 (2450,0-2483,5 MHz), pero no hay restriccion para el uso de estos equipos dentro de areas cerradas porque operan con frequencia de uso secundario. Para uso en areas abiertas, la banda de frequencia esta restringida. On Mexican territory wireless devices may only use channel 11 (2450.0-2483.5 MHz), however for indoors use there are no restrictions on for using all channels, because use of this equipment in Mexico is on secundary basis. En el territorio mexicano, los dispositivos inalmbricos slo pueden usar el canal 11 (2450,0-2483,5 MHz), pero no hay restriccion para el uso de estos equipos dentro de areas cerradas porque operan con frequencia de uso secundario. Para uso en areas abiertas, la banda de frequencia esta restringida. For indoor use only. Para el uso interior slo.

Mexico Mxico

Mexico Mxico

Alpha-1: G11FNF COFETEL: PCPPRG103-250

Mexico Mxico

Alpha-1: C38WCW COFETEL: PRTIPRC303-088-A1

Mexico Mxico Mexico Mxico

AP-700: AP-AG-AT-01 AP-4000: AP-AG-AT-02

COFETEL: RCPPRAP03-537 COFETEL: RCPPRAP03-537

Mexico Mxico

Alpha-1: A13QBF COFETEL: PTIPRAL03-094

231

Regulatory Information
Country Pays Paese Land Pas Radio Transmitter Approval Reference Restrictions metteur Radio Numro du Permis Restrictions Trasmittente de Numero di Limitazioni Radio Approvazione Beschrnkungen Radio-bermittler Zustimmung-Nummer Restricciones Transmisor de Nmero de Permiso Radio PC24E-H-FC PC24E-H-ET-L CE 0122 ! No 67 License required for outdoor installations. Check with reseller for procedure to follow. Vergunning vereist voor buiteninstallatie. Raadpleeg de doorverkoper voor te volgen procedures.

Netherlands Nederland

R0167 SDR3a; NL99061474 HDTP/RDR/485997 CE 0122 ! CE 0336 ! CE 0336 !

PC24E-H-ET PC24E-11-FC/R PC24E-11-ET/R

Only indoor with integral or approved Range Extender Antenna. Alleen voor gebruik binnenshuis met ingebouwde of goedgekeurde reikwijdteversterkerantenne. Only indoor with integral or approved Range Extender Antenna. Alleen voor gebruik binnenshuis met ingebouwde of goedgekeurde reikwijdteversterkerantenne. For indoor use only. Alleen voor gebruik binnen.

Netherlands Nederland

G11FNF-PC G13ENE-PC

CE 0336 ! CE 0336 !

Netherlands Nederland

PC50E-4-ET/A PC50E-4-ET/B PC50E-4-ET/C PC50E-8-ET/A A19PCE-PC

CE 0336 ! CE 0336 ! CE 0336 ! CE 0336 ! CE 0560 !

Netherlands Nederland

Alpha-1: B13ENE CE 0336 !

Only indoor with integral or approved Range Extender Antenna. Alleen voor gebruik binnenshuis met ingebouwde of goedgekeurde reikwijdteversterkerantenne. Only with approved Range Extender Antenna. Alleen gebruiken met goedgekeurde externe antenne. Only indoor with integral or approved Range Extender Antenna. Alleen binnen te gebruiken met goedgekeurde Externe Antenne. Only indoor with integral or approved Range Extender Antenna. Alleen binnen te gebruiken met goedgekeurde Externe Antenne. For indoor use only. Alleen voor gebruik binnen.

Netherlands Nederland

Alpha-1: G11FNF CE 0336 ! Alpha-1: G13ENE CE 0336 !

Netherlands Nederland

Alpha-1: C38WCW CE 0560 !

Netherlands Nederland Netherlands Nederland Netherlands Nederland

AP-700: AP-AG-AT-01 AP-4000: AP-AG-AT-02 Alpha-1: A04LAE

CE 0560 ! CE 0560 ! CE 0336 !

Alpha-1: A08NAE CE 0336 !

232

Regulatory Information
Country Pays Paese Land Pas Radio Transmitter Approval Reference Restrictions metteur Radio Numro du Permis Restrictions Trasmittente de Numero di Limitazioni Radio Approvazione Beschrnkungen Radio-bermittler Zustimmung-Nummer Restricciones Transmisor de Nmero de Permiso Radio RFS ENG 3/2/RFS29 RFS

New Zealand PC24E-H-FC PC24E-11-FC/R PC24E-H-ET-L PC24E-H-ET PC24E-11-ET/R Norway Norsk PC24E-H-FC PC24E-H-ET-L PC24E-H-ET PC24E-11-FC/R PC24E-11-ET/R

ENG 3/2/RFS29 CE 0122 ! R0167 SRD3a

CE 0336 !

Only indoor with integral or approved Range Extender Antenna. Bare innendrs med integral eller godkjent antenne med utvidet rekkevidde. Only indoor with integral or approved Range Extender Antenna. Bare innendrs med integral eller godkjent antenne med utvidet rekkevidde. Only indoor with integral or approved Range Extender Antenna. Bare innendrs med integral eller godkjent antenne med utvidet rekkevidde. Only indoor with integral or approved Range Extender Antenna. Bare innendrs med integral eller godkjent antenne med utvidet rekkevidde. For indoor use only. Bruk bare innenfor Only indoor with integral or approved Range Extender Antenna. Bare innendrs med integral eller godkjent antenne med utvidet rekkevidde. Only indoor with integral or approved Range Extender Antenna. Bare innendrs med integral eller godkjent antenne med utvidet rekkevidde. For indoor use only. Bruk bare innenfor.

Norway Norsk

G11FNF-PC G13ENE-PC

CE 0336 ! CE 0336 !

Norway Norsk

Alpha-1: C38WCW CE 0560 !

Norway Norsk Norway Norsk Norway Norsk

AP-700: AP-AG-AT-01 AP-4000: AP-AG-AT-02 PC50E-4-ET/A A19PCE-PC

CE 0560 ! CE 0560 ! CE 0336 ! CE 0560 !

Norway Norsk

Alpha-1: B13ENE CE 0336 !

Norway Norsk

Alpha-1: G11FNF CE 0336 ! Alpha-1: G13ENE CE 0336 !

Norway Norsk Peru

Alpha-1: A04LAE

CE 0336 !

PC24E-H-FC

AVBS1816

233

Regulatory Information
Country Pays Paese Land Pas Radio Transmitter Approval Reference Restrictions metteur Radio Numro du Permis Restrictions Trasmittente de Numero di Limitazioni Radio Approvazione Beschrnkungen Radio-bermittler Zustimmung-Nummer Restricciones Transmisor de Nmero de Permiso Radio PC24E-H-FC PC24E-H-FC/R PC24E-H-ET-L PC24E-H-ET PC24E-H-ET/R Portugal PC24E-H-FC PC24E-11-FC/R PC24E-11-ET/R 072/2002 CE 0122 ! CE 0336 ! Only indoor with integral or approved Range Extender Antenna. Somente indoor com a antena integral ou aprovada do extender da escala. Only indoor with integral or approved Range Extender Antenna. Somente indoor com a antena integral ou aprovada do extender da escala. Only indoor with integral or approved Range Extender Antenna. Somente indoor com a antena integral ou aprovada do extender da escala. Only indoor with integral or approved Range Extender Antenna. Somente indoor com a antena integral ou aprovada do extender da escala. For indoor use only. Para dentro de casa usar apenas Only indoor with integral or approved Range Extender Antenna. Somente indoor com a antena integral ou aprovada do extender da escala. 688/2000 072/2002

Poland

Portugal

G11FNF-PC G13ENE-PC

CE 0336 ! CE 0336 !

Portugal

Alpha-1: C38WCW CE 0560 !

Portugal Portugal Portugal

AP-700: AP-AG-AT-01 AP-4000: AP-AG-AT-02 PC50E-4-ET/A A19PCE-PC

CE 0560 ! CE 0560 ! CE 0336 ! CE 0560 !

Portugal

Alpha-1: B13ENE CE 0336 !

Portugal

Alpha-1: G11FNF CE 0336 ! Alpha-1: G13ENE CE 0336 !

Portugal

Alpha-1: A04LAE

CE 0336 !

For indoor use only. Para dentro de casa usar apenas

Russia

G11FNF-PC G13ENE-PC

GOST ME96 GOST ME96

234

Regulatory Information
Country Pays Paese Land Pas Radio Transmitter Approval Reference Restrictions metteur Radio Numro du Permis Restrictions Trasmittente de Numero di Limitazioni Radio Approvazione Beschrnkungen Radio-bermittler Zustimmung-Nummer Restricciones Transmisor de Nmero de Permiso Radio Reference 10/36 of 18-3-2002 Reference 10/36 of 18-3-2002 Reference 10/36 of 18-3-2002 Reference 10/36 of 18-3-2002 Reference 10/36 of 18-3-2002 Reference 1355 HT/T Reference 1355 HT/T IDA: PMREQ-0267-2000 IDA: PMREQ-0029-2002 IDA: PMREQ-WLAN-B-0934 -99 IDA: PMREQ-0030-2002 IDA: PMREQ-0693-2003 IDA: PMREQ-0634-2002 IDA: PMREQ-0122-2003 This equipment is allowed for use in a confined area of a building as well as in localized on-site operation. This equipment is allowed for use in a confined area of a building as well as in localized on-site operation. This equipment is allowed for use in a confined area of a building as well as in localized on-site operation. This equipment is allowed for use in a confined area of a building as well as in localized on-site operation. This equipment is allowed for use in a confined area of a building as well as in localized on-site operation. This equipment is allowed for use in a confined area of a building as well as in localized on-site operation. This equipment is allowed for use in a confined area of a building as well as in localized on-site operation.

Saudi Arabia PC24E-H-FC PC24E-11-FC/R PC24E-H-ET PC24E-H-ET-L PC24E-11ET/R Saudi Arabia G11FNF-PC G13ENE-PC Singapore PC24E-H-FC PC24E-11-FC/R PC24E-H-ET

PC24E-11-ET/R Singapore G13ENE-PC

Singapore

PC50E-4-FC/A A09SBS-PC

Singapore

Alpha-1: B13ENE IDA: PMREQ-0121-2003 Alpha-1: G13ENE IDA: PMREQ-0688-2003 Alpha-1: C38WCW IDA: pending

Singapore

Singapore

Singapore Singapore Singapore

AP-700: AP-AG-AT-01 AP-4000: AP-AG-AT-02 Alpha-1: A09SBS

IDA: pending IDA: pending

This equipment is allowed for use in a confined area of a building as well as in localized on-site operation.

235

Regulatory Information
Country Pays Paese Land Pas Radio Transmitter Approval Reference Restrictions metteur Radio Numro du Permis Restrictions Trasmittente de Numero di Limitazioni Radio Approvazione Beschrnkungen Radio-bermittler Zustimmung-Nummer Restricciones Transmisor de Nmero de Permiso Radio PC24E-H-FC PC24E-H-ET-L PC24E-H-ET South Africa G11FNF-PC G13ENE-PC Spain Espaa PC24E-H-FC PC24E-H-ET-L PC24E-H-ET PC24E-11-FC/R PC24E-11-ET/R ICASA: TA-2003/93 ICASA: TA-2003/93 CE 0122 ! 01 00 0196 01 00 0195 CE 0336 ! CE 0336 ! Only indoor with integral or approved Range Extender Antenna. Slo en interiores, con antena integrada o antena de extensin de alcance aprobada Only indoor with integral or approved Range Extender Antenna. Slo en interiores, con antena integrada o antena de extensin de alcance aprobada. Only indoor with integral or approved Range Extender Antenna. Slo en interiores, con antena integrada o antena de extensin de alcance aprobada Only indoor with integral or approved Range Extender Antenna. Slo en interiores, con antena integrada o antena de extensin de alcance aprobada Only indoor with integral or approved Range Extender Antenna. Slo en interiores, con antena integrada o antena de extensin de alcance aprobada

South Africa

Spain Espaa

G11FNF-PC G13ENE-PC

CE 0336 ! CE 0336 !

Spain Espaa

Alpha-1: B13ENE CE 0336 !

Spain Espaa

Alpha-1: G11FNF CE 0336 ! Alpha-1: G13ENE CE 0336 !

Spain Espaa Spain Espaa Sweden Sverige

AP-700: AP-AG-AT-01 AP-4000: AP-AG-AT-02 PC24E-H-FC PC24E-H-ET-L PC24E-H-ET PC24E-11-FC/R PC24E-11-ET/R

CE 0336 ! CE 0336 ! CE 0122 ! Ue990137 CE 0122 ! CE 0336 ! CE 0336 !

Only indoor with integral or approved Range Extender Antenna. Endast inomhus med integrerad antenn eller godknd antenn med lngre rckvidd.

236

Regulatory Information
Country Pays Paese Land Pas Radio Transmitter Approval Reference Restrictions metteur Radio Numro du Permis Restrictions Trasmittente de Numero di Limitazioni Radio Approvazione Beschrnkungen Radio-bermittler Zustimmung-Nummer Restricciones Transmisor de Nmero de Permiso Radio G11FNF-PC G13ENE-PC CE 0336 ! CE 0336 ! Only indoor with integral or approved Range Extender Antenna. Endast inomhus med integrerad antenn eller godknd antenn med lngre rckvidd. Only indoor with integral or approved Range Extender Antenna. Endast inomhus med integrerad antenn eller godknd antenn med lngre rckvidd. Only indoor with integral or approved Range Extender Antenna. Endast inomhus med integrerad antenn eller godknd antenn med lngre rckvidd. For indoor use only. Fr indoor anvnda bara.

Sweden Sverige

Sweden Sverige

Alpha-1: C38WCW CE 0560 !

Sweden Sverige Sweden Sverige Sweden Sverige

AP-700: AP-AG-AT-01 AP-4000: AP-AG-AT-02 PC50E-4-ET/A PC50E-4-ET/B PC50E-4-ET/C

CE 0560 ! CE 0560 ! CE 0336 ! CE 0336 ! CE 0336 !

Sweden Sverige

Alpha-1: B13ENE CE 0336 !

Only indoor with integral or approved Range Extender Antenna. Endast inomhus med integrerad antenn eller godknd antenn med lngre rckvidd. Only indoor with integral or approved Range Extender Antenna. Endast inomhus med integrerad antenn eller godknd antenn med lngre rckvidd. For indoor use only. Fr indoor anvnda bara.

Sweden Sverige

Alpha-1: G11FNF CE 0336 ! Alpha-1: G13ENE CE 0336 !

Sweden Sverige Switzerland Suisse Schweiz Svizzera

Alpha-1: A04LAE

CE 0336 !

PC24E-H-FC PC24E-H-ET-L PC24E-H-ET PC24E-11-FC/R PC24E-11-ET/R

CE 0122 ! BAKOM 99.0538.L.P CE 0122 ! CE 0336 ! CE-0336 ! Only indoor with integral or approved Range Extender Antenna. Pour usage intrieur uniquement, avec une antenne intgrale ou amplificatrice approuve. Nur zum Einsatz innerhalb von Gebuden (mit der integrierten Antenne oder einer zugelassenen Reichweitenverstrkerantenne). Solo per interni con Antenna Range Extender integrale o approvata.

237

Regulatory Information
Country Pays Paese Land Pas Radio Transmitter Approval Reference Restrictions metteur Radio Numro du Permis Restrictions Trasmittente de Numero di Limitazioni Radio Approvazione Beschrnkungen Radio-bermittler Zustimmung-Nummer Restricciones Transmisor de Nmero de Permiso Radio G11FNF-PC G13ENE-PC CE 0336 ! CE 0336 ! Only indoor with integral or approved Range Extender Antenna. Pour usage intrieur uniquement, avec une antenne intgrale ou amplificatrice approuve. Nur zum Einsatz innerhalb von Gebuden (mit der integrierten Antenne oder einer zugelassenen Reichweitenverstrkerantenne). Solo per interni con Antenna Range Extender integrale o approvata. For indoor use only. Pour usage intrieur uniquement. Nur fr Innengebrauch. Per uso interno solo. Only indoor with integral or approved Range Extender Antenna. Pour usage intrieur uniquement, avec une antenne intgrale ou amplificatrice approuve. Nur zum Einsatz innerhalb von Gebuden (mit der integrierten Antenne oder einer zugelassenen Reichweitenverstrkerantenne). Solo per interni con Antenna Range Extender integrale o approvata. Only indoor with integral or approved Range Extender Antenna. Pour usage intrieur uniquement, avec une antenne intgrale ou amplificatrice approuve. Nur zum Einsatz innerhalb von Gebuden (mit der integrierten Antenne oder einer zugelassenen Reichweitenverstrkerantenne). Solo per interni con Antenna Range Extender integrale o approvata. Only indoor with integral or approved Range Extender Antenna. Pour usage intrieur uniquement, avec une antenne intgrale ou amplificatrice approuve. Nur zum Einsatz innerhalb von Gebuden (mit der integrierten Antenne oder einer zugelassenen Reichweitenverstrkerantenne). Solo per interni con Antenna Range Extender integrale o approvata.

Switzerland Suisse Schweiz Svizzera

Switzerland Suisse Schweiz Svizzera Switzerland Suisse Schweiz Svizzera

PC50E-4-ET/A A19PCE-PC

CE 0336 ! CE 0560 !

Alpha-1: B13ENE CE 0336 !

Switzerland Suisse Schweiz Svizzera

Alpha-1: G11FNF CE 0336 ! Alpha-1: G13ENE CE 0336 !

Switzerland Suisse Schweiz Svizzera

Alpha-1: C38WCW CE 0560 !

238

Regulatory Information
Country Pays Paese Land Pas Radio Transmitter Approval Reference Restrictions metteur Radio Numro du Permis Restrictions Trasmittente de Numero di Limitazioni Radio Approvazione Beschrnkungen Radio-bermittler Zustimmung-Nummer Restricciones Transmisor de Nmero de Permiso Radio AP-700: AP-AG-AT-01 CE 0560 ! For indoor use only. Pour usage intrieur uniquement. Nur fr Innengebrauch. Per uso interno solo.

Switzerland Suisse Schweiz Svizzera

Switzerland Suisse Schweiz Svizzera

AP-4000: AP-AG-AT-02

CE 0560 !

Switzerland Suisse Schweiz Svizzera Thailand Thailand Thailand Thailand Taiwan

Alpha-1: A04LAE

CE 0336 !

For indoor use only. Pour usage intrieur uniquement. Nur fr Innengebrauch. Per uso interno solo.

PC24E-H-ET

0704/4184

Alpha-1: G13ENE 4937 G11FNF-PC G13ENE-PC PC24E-H-FC PC24E-11-FC/R 5361 5361 DGT: 89LP0064 (98-7-24) DGT: 91LP0025 (91-2-5) DGT: 92LP0349 DGT: 92LP0444 DGT: 92LP0275 BSMI 3912A213

Taiwan Taiwan Taiwan Taiwan Taiwan Taiwan Taiwan Taiwan

G11FNF-PC A09TBT-PC Alpha-1: B11FNF

Alpha-1: G13FNF DGT: 92LP0350 Alpha-1: C38WCW DGT: 92LP0607 AP-700: AP-AT-AG-01 AP-4000: AP-AT-AG-02 Alpha-1: A09TBT DGT: pending DGT: pending DGT: 92LP0276

239

Regulatory Information
Country Pays Paese Land Pas Radio Transmitter Approval Reference Restrictions metteur Radio Numro du Permis Restrictions Trasmittente de Numero di Limitazioni Radio Approvazione Beschrnkungen Radio-bermittler Zustimmung-Nummer Restricciones Transmisor de Nmero de Permiso Radio PC24E-H-FC PC24E-H-ET-L PC24E-H-ET PC24E-11-FC/R PC24E-11-ET/R United Kingdom G11FNF-PC G13ENE-PC United Kingdom United Kingdom United Kingdom United Kingdom CE 0122 ! R0167 SRD3a CE 0122 ! CE 0336 ! CE 0336 ! CE 0336 ! CE 0336 ! Only indoor with integral or approved Range Extender Antenna. Only indoor with integral or approved Range Extender Antenna. Only indoor with integral or approved Range Extender Antenna. Only indoor with integral or approved Range Extender Antenna.

United Kingdom

Alpha-1: C38WCW CE 0560 !

AP-700: AP-AT-AG-01 AP-4000: AP-AT-AG-02 PC50E-4-ET/A PC50E-8-ET/A A19PCE-PC

CE 0560 ! CE 0560 ! CE 0336 ! CE 0336 ! CE 0560 !

For indoor use only.

United Kingdom United Kingdom

Alpha-1: B13ENE CE 0336 !

Only indoor with integral or approved Range Extender Antenna. For indoor use only.

Alpha-1: A04LAE

CE 0336 !

Alpha-1: A08NAE CE 0336 ! United Kingdom Alpha-1: G11FNF CE 0336 ! Alpha-1: G13ENE CE 0336 ! USA PC24E-H-FC PC24E-11-FC/R FCC ID: IMRWLPCE24H FCC ID: IMRWLPCE2411R FCC ID: IMRWLPC2411R FCC ID: HZB-G11FNFPC FCC ID: IMRWLPCE508A FCC ID: HZB-A13QBFPC Only indoor with integral or approved Range Extender Antenna. For indoor use only. Only indoor with integral or approved Range Extender Antenna. Only indoor with integral or approved Range Extender Antenna.

PC24-11-FC/R USA G11FNF-PC

USA

PC50E-8-FC/A A13QBF-PC

240

Regulatory Information
Country Pays Paese Land Pas Radio Transmitter Approval Reference Restrictions metteur Radio Numro du Permis Restrictions Trasmittente de Numero di Limitazioni Radio Approvazione Beschrnkungen Radio-bermittler Zustimmung-Nummer Restricciones Transmisor de Nmero de Permiso Radio Alpha-1: B11FNF FCC ID: HZB-B11FNF

USA USA USA USA USA USA Venezuela

Alpha-1: G11FNF FCC ID: HZB-G11FNF Alpha-1: A13QBF FCC ID: HZB-A13QBF For indoor use only. Alpha-1: C38WCW FCC ID: HZB-C38WCW For indoor use only. AP-700: AP-AG-AT-01 AP-4000: AP-AG-AT-02 PC24E-11-FC/R FCC ID: IXMAPAGAT01 FCC ID: IXMAPAGAT01 CONATEL: 01388301 For indoor use only. For indoor use only.

For Radio Type Numbers with the format PCxxE-y-zz: xx =24 identifies a IEEE 802.11b compliant WLAN radio product for the 2.4 GHz frequency band. 50 identifies a IEEE 802.11a compliant WLAN radio product for the 5 GHz frequency band. E = optional identifier to indicate that the transmitter has an integral antenna. y =H or 11 identifies a transmitter that supports high speed data transfer of 11, 5.5, 2 and 1 Mbps. 4 or 8 identifies the number of channels. zz =FC or FC/R identifies a 11 channel FCC compliant worldcard restricted to operate in the 2.412 - 2.462 GHz frequency band. FC/A identifies a IEEE 802.11a radio transmitter compliant with the FCC rules. ET or ET/R identifies a 13 channel radio transmitter compliant with the European Union regulations. ET/A or ET/B or ET/C identifies a IEEE 802.11a radio transmitter, compliant with the European Union regulations. FR or FR/R identifies a radio transmitter compliant with the French regulations. JP or JP/R identifies a 14 channel radio transmitter compliant with the Japanese regulations. JP/A identifies a IEEE 802.11a radio transmitter compliant with the Japanese regulations. For Radio Type Numbers with the format qrrsss: q =B identifies a IEEE 802.11b compliant WLAN radio product for the 2.4 GHz frequency band. C identifies a product that conforms to IEEE 802.11a/b/g G identifies a IEEE 802.11g compliant WLAN radio product for the 2.4 GHz frequency band. A identifies a IEEE 802.11a compliant WLAN radio product for the 5 GHz frequency band. rr = 04, 05, 08, 09, 11, 13, 14 or 19 identifies the number of channels. sss = ENE /LAE / NAE / PCE = ETSI (Europe) FNF /QBF = FCC GNJ / LEJ = Japan INI = Israel Le code pour le type de radio qui a le format PCxxE-y-zz : xx =24 indique un produit conforme la norme IEEE 802.11b avec une radio 2,4 GHz. 50 indique un produit conforme la norme IEEE 802.11a avec une radio 5 GHz. E =identificateur facultatif pour indiquer que l'metteur a une antenne intgrale. y =H ou 11 indique un metteur qui prend en charge les transferts haute vitesse : 11, 5.5, 2 and 1 Mb/s. SBS = Singapore TBT = Taiwan VBA = Asia (China, South Korea) WCW = WORLD

241

Regulatory Information
4 ou 8 indique le nombre de canaux. zz =FC ou FC/R identifie un carte universelle 11 canaux, conforme aux normes FCC, qui opre dans la zone de 2.412 - 2.462 GHz seulement. FC/A identifie un metteur radio IEEE 802.11a conforme aux normes FCC. ET ou ET/R identifie un metteur radio 13 canaux conforme aux normes de la Communaut Europene. ET/A ou ET/B ou ET/C identifie un metteur radio IEEE 802.11a conforme aux normes de la Communaut Europene. FR ou FR/R identifie un metteur radio conforme aux normes franaises. JP ou JP/R identifie un metteur radio 14 canaux conforme aux normes japonaises. JP/A identifie un metteur radio IEEE 802.11a conforme aux normes japonaises. Le code pour le type de radio qui a le format qrrsss: q =B indique un produit conforme la norme IEEE 802.11b avec une radio 2,4 GHz. C identifie un produit qui se conforme IEEE 802.11a/b/g G indique un produit conforme la norme IEEE 802.11g avec une radio 2,4 GHz. A indique un produit conforme la norme IEEE 802.11a avec une radio 5 GHz. rr = 04, 05, 08, 09, 11, 13, 14 ou 19 indique le nombre de canaux. sss = ENE /LAE / NAE / PCE = ETSI (Europe) FNF /QBF = FCC GNJ / LEJ = Japan INI = Israel Il numero del tipo di radio che ha il formato PCxxE-y-zz: xx =24 identifica un prodotto che conforma alle normative IEEE 802.11b per una radio a 2,4 GHz. 50 identifica un prodotto che conforma alle normative IEEE 802.11b per una radio a 5 GHz. E =contrassegno facoltativo per indicare che il trasmettitore ha un'antenna integrale. y =H o 11 identifica un trasmettitore che supporta alle normative di alta velocit: 11, 5.5, 2 and 1 Mb/s. 4 o 8 identifica il nombre de canales. zz =FC o FC/R identifica un trasmittore a 11 canali conforma alle normative FCC che funciona nella banda di 2.412 2.462 GHz. FC/A identifica un trasmittore radio IEEE 802.11a conforma alle normative FCC. ET o ET/R identifica un trasmittore a 13 canali conforma alle normative della Comunit Europea. ET/A o ET/B o ET/C identifica un trasmittore radio IEEE 802.11a conforma alle normative della Comunit Europea. FR o FR/R identifica un trasmittore radio che conforma alle normative in vigore in Francia. JP o JP/R identifica un trasmittore a 13 canali conforma alle normative nel Giappone. JP/A identifica un trasmittore radio IEEE 802.11a conforma alle normative nel Giaponne. Il numero del tipo di radio che ha il formato qrrsss: q =B identifica un prodotto che conforma alle normative IEEE 802.11b per una radio a 2,4 GHz. C identifica un prodotto che conforme a IEEE 802.11a/b/g G identifica un prodotto che conforma alle normative IEEE 802.11g per una radio a 2,4 GHz. A identifica un prodotto che conforma alle normative IEEE 802.11b per una radio a 5 GHz. rr = 04, 05, 08, 09, 11, 13, 14 o 19 identifica il nombre de canales. sss = ENE /LAE / NAE / PCE = ETSI (Europe) FNF /QBF = FCC GNJ / LEJ = Japan INI = Israel SBS = Singapore TBT = Taiwan VBA = Asia (China, South Korea) WCW = WORLD SBS = Singapore TBT = Taiwan VBA = Asia (China, South Korea) WCW = WORLD

Die Nummer des Transmittertyps die hat das Format PCxxE-y-zz: xx =24 kennzeichnet ein WLAN IEEE 802.11b geflliges Radioprodukt fr das 2,4 GHz Frequenzband. 50 kennzeichnet ein WLAN IEEE 802.11a geflliges Radioprodukt fr das 5 GHz Frequenzband.

242

Regulatory Information
E =wahlweise freigestellte Kennung, zum anzuzeigen, da der bermittler eine integrale Antenne hat. y =H oder 11 kennzeichnet einen Funksender, der hohe Datentransferraten bis zu 11, 5,5, 2 und 1 Mbps untersttzt. 4 oder 8 kennzeichnet die Zahl Funkkanlen. zz =FC oder FC/R kennzeichnet eine FCC-konforme "Worldcard" mit 11 Kanlen, die auf den Betrieb in einem Frequenzband von 2,412 - 2,462 GHz beschrnkt ist. FC/A kennzeichnet einen IEEE 802.11a Radiobermittler, der mit den FCC Richtlinien gefllig ist.. ET oder ET/R kennzeichnet einen Funksender mit 13 Kanlen, der mit den EG-Bestimmungen konform ist. ET/A oder ET/B oder ET/C kennzeichnet einen IEEE 802.11a Radiobermittler, der mit europischen Regelungen gefllig ist. FR oder FR/R kennzeichnet einen IEEE 802.11a Radiobermittler, der mit franzsische Regelungen gefllig ist. JP oder JP/R kennzeichnet einen Funksender mit 14 Kanlen, der mit den japanischen Bestimmungen konform ist. JP/A kennzeichnet einen IEEE 802.11a Radiobermittler, der mit japanische Regelungen gefllig ist. Die Nummer des Transmittertyps die hat das Format qrrsss: q =B kennzeichnet ein WLAN IEEE 802.11a geflliges Radioprodukt fr das 2,4 GHz Frequenzband. C kennzeichnet ein Produkt, das an IEEE 802.11a/b/g sich anpat G kennzeichnet ein WLAN IEEE 802.11g geflliges Radioprodukt fr das 2,4 GHz Frequenzband. A kennzeichnet ein WLAN IEEE 802.11a geflliges Radioprodukt fr das 5 GHz Frequenzband. rr = 04, 05, 08, 09, 11, 13, 14 oder 19 kennzeichnet die Zahl Funkkanlen. SBS = Singapore TBT = Taiwan VBA = Asia (China, South Korea) WCW = WORLD sss = ENE /LAE / NAE / PCE = ETSI (Europe) FNF /QBF = FCC GNJ / LEJ = Japan INI = Israel El nmero de tipo de radio que tiene el formato PxxE-y-zz: xx =24 identifica un producto de radio obediente el estandard WLAN IEEE 802.11b para la banda de frecuencia de 2,4 GHz. 50 identifica un producto de radio obediente el estandard WLAN IEEE 802.11a para la banda de frecuencia de 5 GHz. E =identificador opcional para indicar que el transmisor tiene una antena integral. y =H o 11 identifica un transmisor que soporta transferencia de datos a alta velocidad de 11, 5,5, 2 y 1 Mbps. 4 o 8 identifica el nmero de canales. zz =FC o FC/R identifica una 'worldcard' de 11 canales que cumple con la FCC, limitada para operar nicamente en la banda de frecuencia 2,412 - 2,462 GHz. FC/A identifica un radiotransmisor de IEEE 802.11a obediente con las reglas de la FCC. ET o ET/R identifica un radiotransmisor de 13 canales que cumple con las regulaciones de la Unin Europea. ET/A o ET/B o ET/C identifica un radiotransmisor de IEEE 802.11a obediente con las regulaciones de la union europea. FR o FR/R identifica un radiotransmisor de IEEE 802.11a obediente con las regulaciones francesas. JP o JP/R identifica un radiotransmisor de 14 canales que cumple con las regulaciones japonesas. JP/A identifica un radiotransmisor de IEEE 802.11a obediente con las regulaciones japonesas. El nmero de tipo de radio que tiene el formato qrrsss: q =B identifica un producto de radio obediente el estandard WLAN IEEE 802.11a para la banda de frecuencia de 2,4 GHz. C identifica un producto que se conforme con IEEE 802.11a/b/g G identifica un producto de radio obediente el estandard WLAN IEEE 802.11g para la banda de frecuencia de 2,4 GHz. A identifica un producto de radio obediente el estandard WLAN IEEE 802.11a para la banda de frecuencia de 5 GHz rr = 04, 05, 08, 09, 11, 13, 14 o 19 identifica el nmero de canales. sss = ENE /LAE / NAE / PCE = ETSI (Europe) FNF /QBF = FCC SBS = Singapore TBT = Taiwan

243

Regulatory Information
GNJ / LEJ = Japan INI = Israel VBA = Asia (China, South Korea) WCW = WORLD

PCxxE-y-zz xx =24 2.4 GH IEEE 802.11b WLAN 50 5 GH IEEE 802.11a WLAN E = y =H 11 115.52 1 Mbps 4 8 zz =FC FC/R 2.412 ~ 2.462 GHz FCC 11 Worldcard FC/A FCC IEEE 802.11a ET = ET/R 13 ET/A ET/B ET/C IEEE 802.11a FR FR/R JP JP/R 14 JP/A IEEE 802.11a qrrsss q =B 2.4 GHz IEEE 802.11b WLAN G 2.4 GHz IEEE 802.11g WLAN A 5 GHz IEEE 802.11a WLAN rr =04050809111314 19
sss = ENE /LAE / NAE / PCE = ETSI (Europe) FNF /QBF = FCC GNJ / LEJ = Japan INI = Israel SBS = Singapore TBT = Taiwan VBA = Asia (China, South Korea) WCW = WORLD

244