BS5839 PART 1: 2017

A GUIDE TO FIRE ALARM SYSTEMS DESIGN

 WELCOME
This guide has been developed to highlight the key
points of the latest version of the standard:

BS5839 Fire detection and fire alarm systems for

buildings – Part 1 2017: Code of practice for design,
installation, commissioning and maintenance of
systems in non-domestic premises.

The guide should not be used as a substitute for the

standard.

This guide will be of particular interest for those

designers and installers that need simple guidance
to the selection, spacing and location of fire devices.

2
CATEGORIES
Fire Alarm and Fire Detection systems are categorised in the
following way:

P - AFD* designed to primarily

protect property
P1 - AFD installed throughout all
areas
P2 - AFD Installed only in
defined areas

L - AFD designed to primarily

protect human life
L1 - AFD installed throughout
all areas
L2 - AFD Installed in defined
areas in addition to L3
L3 - AFD installed in escape
routes and rooms opening
onto these routes
L4 - AFD installed in escape
routes comprising circulation
areas and spaces such as
corridors and stairways
L5 - A non-prescriptive system
in which the protected
area(s) is designed to satisfy
a specific fire risk objective
(other than that of L1 to L4)
M - System designed to be operated
manually (no AFD)
*AFD = Automatic Fire Detection

3
 SMOKE DETECTORS

It should be noted that large smoke particles will have a similar particle size to
small particle contaminates including some types of dust and aerosols. As such
care should be taken when siting smoke detectors to limit subjection to this
phenomenon.

HEAT DETECTORS

The minimum static response of heat devices should not be less than 29°C
above the average ambient temperature, or less than 4°C above the highest
temperature the device can be expected to experience.

4
FIRE DETECTOR COVERAGE & POSITIONING

Smoke detection devices have an individual coverage of 7.5m radius. However

these radii must overlap to ensure there are no ‘blind spots’. Therefore the
individual coverage can be represented by a square measuring 10.6 x 10.6m
giving an actual area coverage of 112m² per device.

Heat detection devices have an individual coverage of 5.3m radius. However

these radii must overlap to ensure there are no ‘blind spots’. Therefore the
individual coverage can be represented by a square measuring 7.5 x 7.5m giving
an actual area coverage of 56.3m² per device.

5
 In corridors less than 2m wide the horizontal spacing of detectors may be
increased, the areas of coverage need not overlap as in the case of a room. Any
corridor over 2m wide is deemed a room and device spacing should follow the
standard for rooms (see page 5).

6
Detectors must not be sited less than 1m from air inlets or air conditioning units.

A device should not be mounted within 500mm of any obstruction. If the top of a
solid partition is less than 300mm from the ceiling then treat it as a wall. Similarly,
ceiling obstructions such as beams should be treated as walls if deeper than 10%
of the ceiling height.

7
 Never mount devices closer than twice the depth of light fittings.

Voids less than 800mm in height need not have independent coverage, unless
fire or smoke is able to spread from one area to another through the void or risk
assessment shows AFD (Automatic Fire Detection) to be necessary.

8
For ceilings that feature an apex: as long as the height of the apex from the
rest of the ceiling is less than 150mm for heat detectors or less than 600mm
for smoke detectors then these can be treated the same as flat ceilings. For
higher apexes, a device should be installed at the highest point. The distance to
adjacent devices can be increased by 1% per degree of angle of the roof up to a
maximum of 25%.

Ceiling Height (m)

Detector Type General Limits Maximum

Heat RoR 9.0 10.5

Heat Fixed 7.5 12.5
Point Smoke Detector 10.5 12.5
Aspirating Smoke Detection Class C with 5 holes 15 18
Aspirating Smoke Detection Class C with 15 holes 25 28
Aspirating Smoke Detection Class B with 5 holes 40 43
Optical Beam Normal Sensitivity 25 28
Optical Beam Enhanced Sensitivity 40* 43
*Supplemented detection recommended unless risk of stratification is minimal.

9
 Vertical shafts like lifts and stairways should have a device mounted within 1.5m
of any opening.

Enclosed stairways should have a detector on each main landing.

10
DETECTOR SPECIFICATION

The sensing element of a heat detection device (thermistor) should not be less
than 25mm below ceiling, and not greater than 150mm below ceiling.

The sensing element of a smoke detection device (photoelectric smoke chamber)

should not be less than 25mm below ceiling, and not greater than 600mm below
ceiling.

11
 SEARCH DISTANCE

A person searching a zone for a fire should not have to travel more than 60m
from the entrance of a zone to identify the source of a fire. Particular attention is
required when siting the detectors LED to minimise the search.

SECOND

FIRST

GROUND

Less than 300m2 can be covered by a single zone. When the total floor area
exceeds 300m2, each floor would require a zone (or zones if the floor area
exceeds 2000m2 ). Stairwells, liftwells or similar should be separate zones.

Zones should not cross floors.

12
MANUAL CALL POINTS (MCP)

1.4m
(+/- 200mm)

The centre of the element of the manual callpoint should be positioned 1.4m
(+/-200mm) from floor level (unless a wheelchair user is likely to be the first
person to raise the alarm, when this is applicable it should be noted on any
certification). All manual call points should be fitted with a protective cover, which
is moved to gain access to the frangible element.

A person should not have to travel more than 45m along an escape route
to reach a manual call point (25m if disabled person to operate, or rapid fire
development is likely). Manual call points should be sited at all stairwells and
exits from the building.

13
 SOUNDERS

The minimum sound level of a sounder device should be 65dB(A) or 5dB(A)

above a background noise which is louder than 60dB(A) (if lasting more than
30 seconds) and at a frequency of between 500Hz and 1000Hz. The maximum
sound level should not be greater than 120dB(A) at any normally accessible
point. Sounder volume may be reduced to 60dB(A) in stairways, enclosures up
to 60m and specific points of limited extent.

Sounder device cabling should be arranged so that in the event of a fault at least
one sounder will remain operational during a fire condition.

14
 75

For areas where people are sleeping, sounder devices should produce a
minimum of 75dB(A) at the bed-head with all doors shut.

-30
FIRE DOOR

Decibel loss occurs through doors. Approximately -20dB(A) through a normal

door, and approximately -30dB(A) through a fire door.

15
 VISUAL INDICATION DEVICES

Visual indication devices (VIDs), such as strobes, can be ceiling or wall mounted.
For wall mounting they should always be mounted 2.1m above floor level. Visual
alarm devices should conform to BS EN 54-23.

Unless MICC cable is used, all cabling should be mechanically protected from
floor level up to a height of 2m.

16
VISUAL ALARM DEVICE CATEGORIES
EN54-23 specifies that the VAD produces an illumination of 0.4 lux on surfaces
perpendicular to the direction of the light emitted from the device. They are
not designed to wake people that are asleep and can be red or white light.
VADs are classified into three categories based on their application:

W - Wall-mounted
C - Ceiling-mounted
O - Open Category

Wall and Ceiling mounting categories are specified at specific installation heights
and particular patterns of coverage - see diagrams. For W and C categories,
the shape of the volume covered is fixed by the standard. The dimensions of
this coverage volume are specified by the manufacturer. For all categories, the
volume covered can be used to determine VAD spacing within the building.
Open category allows manufacturers to specify the coverage shape and volume
and does not put any restriction on mounting height.
Wall-Mounted - Coverage Volume Ceiling-Mounted - Coverage Volume

Wall-mounted VADs cover a cuboid Ceiling-mounted VADs cover a

volume with a square floor area. The cylindrical area. The coverage volume
coverage volume is presented as a is presented as a code in the form
code in the form of W-X-Y, where W is C-X-Y, where C is Ceiling-mounted, X
Wall-mounted, X is the max mounting is the max mounting height (m) and
height (m) and Y is the width and Y is the diameter (m) of the coverage
length (m) of the coverage floor area. volume’s floor area. The max mounting
The min mounting height is 2.4 m. height can only be specified as 3, 6 or
9m.
E.g. : W-2.4-12 means it should be E.g. : C-3-15 means it can be mounted
mounted at 2.4m from the floor and up to 3m from the floor and will cover
will cover an area of up to 12 by 12m. a cylindrical area of least 15m diameter.

17
 CABLING

Fire resistant cabling is now required within the whole fire alarm system
including the main supply cables. The use of non-fire resisting cables, whether
mechanically protected by fire-resisting construction or not, will no longer comply
with BS5839.

To avoid mechanical damage and electromagnetic interference, fire alarm cables

should not be installed in the same conduit as the cables for other services.
Where fire alarm cables share common trunking, a compartment of the trunking,
separated from other compartments by a strong, rigid and continuous partition
reserved solely for fire cables should be implemented.

18
 FIRE DETECTION & ALARM SYSTEMS

®
TWINFLEXpro2
Smart 2-Wire Fire Alarm System
A conventional 2-wire fire alarm
system is often the natural choice for
smaller applications or where budget
constraints exist.

Fike’s TWINFLEXpro2 2-wire fire alarm

system has long been known for its
adaptability and cost-effectiveness
within a variety of applications, big
or small … making it one of the most
flexible products on the market.

Building on those strengths and designed for ease of use and state-of-the-art
monitoring, the LPCB-Approved TWINFLEXpro2 is the next generation in 2-wire
fire alarm reliability.

The Reliable Fire Protection System You Can Count On

This versatile fire alarm system incorporates Fike’s ASD

Multipoint detector using smoke and heat detection with
optional built-in sounder, allowing the whole system to be
installed using only one pair of wires per zone. That means
easier, faster installations AND cost savings.

19
 FIRE DETECTION & ALARM SYSTEMS

DUONET®& QUADNET®
Multi- Loop Intelligent Addressable Systems
The Duonet & Quadnet intelligent fire
alarm systems offer both cost-effective
and reliable solutions for a wide
variety of fire detection applications.
The innovative technology built into
the Duonet and Quadnet panels is
designed to significantly reduce false
alarms. The systems can support up to
200 Multipoint ASD combined detector/
sounders on a single loop.

Integrity of the system is maintained by

way of a built-in isolator incorporated
within every device. System intelligence
has been harnessed in such a way that
equipment used is very easy to install,
commission and maintain.

Intelligent Fire Alarm Solutions

The system has been designed to high specification and

quality standards, and complies with the EN54-2 and EN54-4
standards and EU directives.

20
MULTI-SENSOR DETECTORS
Using the Multipoint ASD detector as part of a Fike system means that when a
detector is wired to the system, a sounder and strobe can also be connected
without extra installation time or cost. This greatly reduces the number of points
that need to be installed and the time it takes to install.
• 7/15 modes of fire detection including combined smoke/heat
• Optional built-in sounder and/or strobe in a single device
• Self-calibrates every 6 hours
• Continuously monitors for dust contamination
• Easily removable for maintenance at height
• LED to report status of detector ( normal / fault / fire )

Fike Multipoint Detectors -

The alternatives don't stack up!

FIKE VIDEO FIRE DETECTION

Specifically for L5 and P2 consultant specified categories, Video Fire Detection
is now a recognised specialised fire detection technique.

Fike Video Analytics is a turnkey video

smoke detection solution. The state-
of-the-art camera-based video smoke
detection system visually detects the
presence of flame or smoke at its
source, independent of airflow in the
area. Fike Video Analytics represents
a critical advantage for early warning
fire detection, especially for challenging
environments and open area venues.

21
 FIKE TRAINING

Module 1: TWINFLEXpro2 - Remote Venues

TWINFLEX system presentation providing an overview of

the control panel, connections and menu structure. Field
devices, fault finding and other associated equipment are
covered. (As part of module 3 in office or remote venues only)

Price - £25 (Includes software)

Module 2: DUONET & QUADNET

Duonet/Quadnet system presentation providing an

overview of the control panel, connections and menu
structure. Field devices, fault finding, associated equipment
and principles of soft addressing are covered.
Price - £50.00 (Includes software)

Module 3: TWINFLEXpro2 / DUONET & QUADNET

Full indepth training on all of Fike’s fire alarm control
panels and associated devices. providing an overview of
the control panels, connections and menu structures. Field
devices, fault finding and other associated equipment are
also covered.

Price - £50.00 (Includes software)

To reserve a place or for more information on

Fike Safety Technology Ltd has a duty of care to
one of the courses, please contact:
ensure that persons are competent for the task.
Fike Safety Technology Ltd,
The training covers the installation and operation of
31 Springvale Industrial Estate,
Fike safety Technology’s product range and does
Cwmbran NP44 58D UK
not cover more general skills and practices relating
Tel: +44 (0) 1633 865 558
to BS5839. Upon completing each module all
E-Mail: [email protected]
delegates will undergo an open book written exam
to ensure they meet the required standard.
Other training modules are also available.

22
CPD Accredited Presentations

CPDs offered by Fike

Introduction to Fire Alarms
This CPD presentation is suitable for anyone wishing to
have a greater understanding of Fire Detection and covers
a range of Detection methods. It also gives overview of
BS5839 Pt1, Pt6 and of the requirements of the ‘responsible
person’. It will enable the attendee to have an understanding of the different types of
Detection currently available in the market place and help them make an informed choice
when selecting and specifying the appropriate system(s) for their requirements.

Introduction to Fire Suppression

This CPD looks into the history of fire suppression and an understanding of how fires
develop including the classification of fire types. It highlights the various types of
extinguishing methods and the different inert and clean agent gases available on the
market, plus the different hazard types / applications and principles of operation including
the benefits of constant or regulatory flow valve systems. We also cover the safe handling
/ transportation of cylinders, pressure relief venting, integrity testing requirements and
F-Gas regulations, with an outline on the basic information required to survey and design
a system.

Introduction To Water Mist

This CPD is aimed at providing an overview on the principles of water mist which can
be further developed for specific applications. The course reviews the background and
development of water mist and provides an understanding of the principles and process
of how water mist efficiently fights fires. The presentation identifies the most common
types of system available in today’s market and identifies suitable applications for each
specific technology. An emphasis is drawn to applicable UK design and installation
standards along with associated system approvals through risk specific type testing.

Introduction to Video Detection

Video analytics is a state-of-the-art camera-based flame & smoke recognition system.
it visually detects the presence of flame / smoke at its source and represents a critical
advantage for early warning fire detection, identifying and reacting to fire situations in
their earliest stages protecting lives and property.
Many of today’s modern large structures may not have adequate fire protection. Atriums,
open areas and high ceilings make the use of traditional detection methods impractical,
ineffective and difficult to maintain. High airflow and stratification can prevent smoke from
reaching point detectors, adding to the ineffectiveness of traditional detection.

23
Sabre Fire and Security Ltd are an authorised Fike supply and service centre.

We are listed in the LPCB (Loss Prevention Certification Board) and The National
Landlords Association Recommended Supplier List. We are also members of the
UKFA (UK Fire Association) and FSB (Federation of Small Business).

Sabre Fire and Security Ltd are the sole UK and European distributors of StoveTop
FireStop® an automatic domestic pan fire suppression system – details can be
found on our website.

SERVICES PROVIDED

Fire alarm design

Fire alarm supply
Fire alarm installation, commission, service and maintenance for both domestic
and commercial properties.
Advice regarding compliance with the latest legislation on fire protection for
commercial and rented properties.
Fire risk assessments for commercial properties and HMO’s.
Fire extinguisher supply, installation, commission and maintenance.

Sabre Fire & Security Ltd

6 South Mundells, Welwyn
Garden City, Herts
AL7 1EP
Tel: 01707 393888
Fax: 01707 393777
[email protected]

WWW.SABRE-FIRE.CO.UK