 Useful Links

UPPCL JE EE 27
Nov 2019
Evening Shift

1
Section : Technical_Electrical Engineering

Q.1 With the increase in cost of preventive maintenance, the breakdown maintenance cost will
______.
Ans A. Decreases

B. Increases at a faster rate

C. No change

D. Increases

Question ID : 8970323023
Status : Answered
Chosen Option : 1

Q.2

Ans A. 0.4

B. 0.6

C. 0.45

D. 0.5

Question ID : 8970323010
Status : Not Answered
Chosen Option : --

Q.3 The most commonly used material for preparing Over Head line insulators is ______.
Ans A. Mica

B. Asbestos

C. PVC

D. Porcelain

Question ID : 8970323021
Status : Answered
Chosen Option : 4

Q.4 Resistivity of platinum is:

Ans A. 10.5 micro ohm cm

B. 49 micro ohm cm
 C. 44 micro ohm cm

D. 24 micro ohm cm

Question ID : 8970323138
Status : Not Answered
Chosen Option : --

Q.5 ______ is device of transformer which takes up expansion and contraction of oil.
Ans A. Buchholz's relay

B. Bushing

C. Conservator

D. Breather

Question ID : 8970323116
Status : Answered
Chosen Option : 3

Q.6 For heavy loads, the relation between torque (T) and slip (S) in induction motor is given by
______.
Ans
A.

B.

C.

D.

Question ID : 8970323036
Status : Answered
Chosen Option : 2

Q.7 In PLC Programming, a retentive function is one that:

Ans A. Cannot be edited or deleted

B. Is not reset after a power loss

C. Default points to OFF State

D. Default points to ON State

Question ID : 8970323043
Status : Not Answered
Chosen Option : --

Q.8 In cleat wiring, cleats shall be fixed at regular intervals not exceeding ______ meters.
Ans A. 0.7

B. 0.4

C. 0.5

D. 0.6

Question ID : 8970323097
Status : Not Answered
Chosen Option : --
Q.9 The current rating of a fuse in a distribution system should not exceed ______.
Ans A. The current rating of the highest cable in the circuit:

B. The average current rating of the circuit

C. The current rating of the smallest cable in the circuit

D. The total load of the circuit

Question ID : 8970323016
Status : Not Answered
Chosen Option : --

Q.10 उ च वो टता लाइन के लए 1956 के भारतीय व ुत नयम 77 (1) के अनुसार, "सड़क के पार कसी भी भाग
म खड़ी क जाने वाली स वस लाइन स हत, ओवरहेड लाइन क ऊंचाई ______ से कम नह होनी चा हए।"
Ans A. 5.795 meters

B. 5.185 meters

C. 6.10 meters

D. 4.575 meters

Question ID : 8970323015
Status : Not Answered
Chosen Option : --

Q.11 Air forced into the tower in mechanical draft cooling towers by using:
Ans A. Spray nozzles

B. Propellers

C. Louvers

D. Deckings

Question ID : 8970323068
Status : Answered
Chosen Option : 1

Q.12 ______ maintenance is regular period planned maintenance which eliminates breakdowns
and outages.
Ans A. Routine

B. Preventive

C. Corrective

D. Operation

Question ID : 8970323024
Status : Answered
Chosen Option : 1

Q.13 In case of stator earth-fault protection of generator, the value of resistance necessary in the
neutral circuit to prevent an overvoltage due to resonance is ______.
Ans
A.

B.

C.
 D.

Question ID : 8970323055
Status : Not Answered
Chosen Option : --

Q.14 Switch mode power supply is used for:

Ans A. Obtaining controlled DC supply

B. Switching over from one supply to another

C. Obtaining AC voltage of low frequencies

D. Obtaining AC voltage of high frequencies

Question ID : 8970323103
Status : Answered
Chosen Option : 1

Q.15 In thyrite lightning arrester, on doubling the voltage the current increases to ______.
Ans A. 4 times

B. 12.6 times

C. 2 times

D. 6.6 times

Question ID : 8970323058
Status : Not Answered
Chosen Option : --

Q.16 In overhead transmission lines, the maximum length of span for RCC poles should be ______
meters.
Ans A. 200 - 400 meters

B. 80 - 100 meters

C. 30 - 70 meters

D. 10 - 20 meters

Question ID : 8970323099
Status : Answered
Chosen Option : 2

Q.17 As per Indian Electricity rule in overhead systems, the recommended span in case of
wooden poles is ______.
Ans A. 100-300 meters

B. 40-50 meters

C. 50-80 meters

D. 80-100 meters

Question ID : 8970323072
Status : Answered
Chosen Option : 1

Q.18 A Bimetallic strip breaks the circuit when:

Ans A. Resistance increases

B. Current rises above its setting value

C. Current decreases to zero

D. Voltage decreases

Question ID : 8970323134
Status : Answered
Chosen Option : 2

Q.19 Causes of electrical failure in rotating machines is due to ______.

Ans A. Core cross-sectional area

B. Winding layer by layer

C. Increase in efficiency

D. Stator winding insulation failure

Question ID : 8970323030
Status : Answered
Chosen Option : 4

Q.20 ______ voltages can be available from a 3 wire DC distribution system.

Ans A. One

B. Four

C. Two

D. Three

Question ID : 8970323077
Status : Not Answered
Chosen Option : --

Q.21 According to IE rules, final sub circuits beyond the distribution board for light, fan and 5A
socket outlet ______.
Ans A. Should not exceed 5 points / 600watts

B. Should not exceed 15 points / 1000watts

C. Should not exceed 6 points / 800watts

D. Should not exceed 10 points / 800watts

Question ID : 8970323020
Status : Answered
Chosen Option : 4

Q.22 Bronze is an alloy of:

Ans A. Copper Cadmium

B. Copper Tin

C. Copper Nickel

D. Copper Chromium

Question ID : 8970323132
Status : Answered
Chosen Option : 2
Q.23 The material used for generator, motor winding and field windings is ______.
Ans A. Enamelled copper wire

B. Super enamelled copper wire

C. Rolled copper bars

D. Silver

Question ID : 8970323140
Status : Answered
Chosen Option : 1

Q.24 When there is a dead end of the line or there is a corner or a sharp curve or the lines crosses
rivers ______ insulator is used.
Ans A. Strain

B. Pin

C. Shackle

D. Stay

Question ID : 8970323031
Status : Answered
Chosen Option : 1

Q.25 During the process of electrolysis, when the same quantity of electricity is passed through
different electrolytes, the mass of substances deposited is proportional to:
Ans A. Molecular numbers

B. Molecular weight

C. Valencies

D. Chemical equivalents

Question ID : 8970323007
Status : Not Answered
Chosen Option : --

Q.26

Ans A. Y= 0, Z= 0

B. Y= 1, Z= 0

C. Y= 0, Z= 1

D. Y= 1, Z= 1

Question ID : 8970323127
Status : Not Answered
 Chosen Option : --

Q.27

Ans A. Two lamps controlled by two switches, all connected in series

B. Two lamps in series, each having a switch in parallel

C. Two lamps each controlled by a separate switch

D. Two lamps in joint box system

Question ID : 8970323092
Status : Answered
Chosen Option : 2

Q.28 The capacitor in a single phase induction motor is used for ______.
Ans A. Improving the power factor

B. Reducing the harmonics

C. Starting the motor

D. Improving the starting torque

Question ID : 8970323032
Status : Answered
Chosen Option : 4

Q.29

Ans A.

B.

C.

D.

Question ID : 8970323147
Status : Not Answered
Chosen Option : --

Q.30 As per IE rules the nominal cross sectional area of the conductor should not be less than
______ if copper is used for sub circuit wiring.
Ans A.

B.

C.
 D.

Question ID : 8970323026
Status : Answered
Chosen Option : 3

Q.31 Thermo-hygrometer is an instrument used in Energy Audit for measurement of:

Ans A. Air velocity and humidification, ventilation in air-conditioning and refrigeration
systems.
B. Spot water analysis of the amount of dissolved salts in water.

C. Spot analysis of effective acidity or alkalinity of a solution or water.

D. Flow of liquids through pipelines of various sizes.

Question ID : 8970323071
Status : Answered
Chosen Option : 1

Q.32 The ratio of current year production to the reference year’s production is called ______.
Ans A. Diversity factor

B. Load factor

C. Maximum demand factor

D. Production factor

Question ID : 8970323064
Status : Answered
Chosen Option : 4

Q.33 Which of the following is used with critical load like hospital intensive care unit where a
temporary power failure can cause lot of inconvenience?
Ans A. UPS

B. LPS

C. SMPS

D. SCS

Question ID : 8970323104
Status : Not Answered
Chosen Option : --

Q.34 What is the commonly used unit of measure for rating an air conditioner?
Ans A. Btu

B. kW

C. Joules

D. Ton

Question ID : 8970323022
Status : Answered
Chosen Option : 4

Q.35 A DC motor is running with a certain load. The effect of adding an external resistance in the
shunt field circuit is ______.
Ans A. To reduce the motor speed

B. To increase the motor speed

C. To stop the motor

D. To reduce the armature current of the motor

Question ID : 8970323113
Status : Answered
Chosen Option : 2

Q.36 In a transmission system, the cost of lost energy is ______.

Ans A. Directly proportional to the square of current

B. Inversely proportional to the square of current

C. Directly proportional to the square of voltage

D. Inversely proportional to the square of voltage

Question ID : 8970323076
Status : Answered
Chosen Option : 1

Q.37 A semiconductor has ______ electrons in its valency ring.

Ans A. 3

B. 6

C. 0

D. 4

Question ID : 8970323131
Status : Answered
Chosen Option : 4

Q.38 For reliable protection of overhead transmission lines from direct lightning strokes using
ground wires, the protection angle ‘a’ between the vertical line through the ground wire axis
and the line passing from the ground wire axis to the outer most line conductor should be
_______.
Ans A.

B.

C.

D.

Question ID : 8970323060
Status : Not Answered
Chosen Option : --

Q.39

Ans A. 10 lakh kCal/hour

B. 6.4 lakh kCal/hour

C. 4.8 lakh kCal/hour

D. 3.2 lakh kCal/hour

Question ID : 8970323070
 Status : Not Answered
Chosen Option : --

Q.40 In an induction motor, the phenomenon of magnetic locking between the stator and the
rotor teeth is called ______.
Ans A. Hunting

B. Skewing

C. Cogging

D. Crawling

Question ID : 8970323035
Status : Answered
Chosen Option : 3

Q.41 When it is said that the duty cycle of a welding machine is 10 %, it means:
Ans A. The machine operates for a duration of two minutes in a period of ten minutes.

B. The actual output of the machine is 10 % of the rated output.

C. The machine operates for a period of one minute only in a ten minute span.

D. The machine operates at 10 % efficiency.

Question ID : 8970323009
Status : Answered
Chosen Option : 3

Q.42 The normal value of coefficient of adhesion with clean dry rails is ______.
Ans A. 0.38

B. 0.25

C. 0.12

D. 0.09

Question ID : 8970323005
Status : Not Answered
Chosen Option : --

Q.43 Utilization factor of a power station is the ratio of:

Ans A. Maximum demand of a power station to the sum of individual maximum demands.

B. Average demand to the rated capacity of the power station.

C. Sum of individual maximum demands to maximum demand of a power station.

D. Maximum demand on the power station to the rated capacity of the power station.

Question ID : 8970323066
Status : Answered
Chosen Option : 4

Q.44 Which rating is provided by Bureau of Energy Efficiency, India to indicate the energy
efficiency of household appliances like refrigerators, water heaters and air conditioners?
Ans A. BIS

B. ISI

C. ISC
 D. Star labelling

Question ID : 8970323063
Status : Not Answered
Chosen Option : --

Q.45 Boards on which various control accessories like energy meter, iron clad switch, fuses etc.
are housed are called ______ boards.
Ans A. Panel

B. Control

C. Standard

D. Switch

Question ID : 8970323096
Status : Answered
Chosen Option : 1

Q.46 Snubber circuits are used with thyristors to:

Ans A. See that SCR turns ON at a voltage much less than its forward break over voltage

B. To protect the gate circuit

C. To limit the rate of rise of voltage dv/dt.

D. To limit the rate of rise of current di/dt.

Question ID : 8970323107
Status : Answered
Chosen Option : 1

Q.47 Constant losses of DC motor can be measured by:

Ans A. Swinburne's Test

B. Retardation Test

C. Hokinson's Test

D. Load Test

Question ID : 8970323115
Status : Answered
Chosen Option : 1

Q.48 If the Reynold's number is greater than 100000, then the flow is ______.
Ans A. Uniform

B. Laminar

C. Turbulent

D. Streamline

Question ID : 8970323145
Status : Not Answered
Chosen Option : --

Q.49 Which one of the following is an Indian Standard Organization?

Ans A. IEC
 B. ISO

C. ANSI

D. BIS

Question ID : 8970323027
Status : Answered
Chosen Option : 2

Q.50 Synchronous motors are particularly attractive for low speed drives below ______.
Ans A. 300 rpm

B. 1500 rpm

C. 800 rpm

D. 1000 rpm

Question ID : 8970323041
Status : Answered
Chosen Option : 2

Q.51 The instrument which is used to measure insulation resistance is:

Ans A. Wheatstone's bridge

B. Megger

C. Ballistic galvanometer

D. Instrument transformer

Question ID : 8970323141
Status : Answered
Chosen Option : 2

Q.52 The function of electrostatic precipitator in a coal based thermal power plant is to:
Ans A. Collect dust from flue gas

B. Clean the turbine blades

C. Collect dust at the air inlet

D. Collect dust from the coal

Question ID : 8970323085
Status : Answered
Chosen Option : 2

Q.53 "M.M.F around any closed path equals the current enclosed by the path". This is known as
_______.
Ans A. Coulomb's law

B. Gauss' law

C. Ampere's law

D. Biot-Savart law

Question ID : 8970323075
Status : Answered
Chosen Option : 2
Q.54 Yaw control in a wind energy power plant:
Ans A. Control the gear speed

B. Rotate the turbine about the vertical axis

C. Control the turbine speed

D. Rotate the turbine about the horizontal axis

Question ID : 8970323086
Status : Answered
Chosen Option : 2

Q.55 The field winding of a DC machine consists of eight coils in series, each containing 1200
turns. When the current is 3A, the flux linked with each coil is 20 mWb, then energy stored is
______.
Ans A. 36 Joules

B. 288 Joules

C. 64 Joules

D. 108 Joules

Question ID : 8970323117
Status : Answered
Chosen Option : 2

Q.56 ______ loss is found from the open circuit test on a transformer.
Ans A. Dielectric

B. Ohmic

C. Copper

D. Core

Question ID : 8970323114
Status : Answered
Chosen Option : 4

Q.57 Armature of the DC machine is laminated to reduce ______.

Ans A. Eddy current loss

B. Copper loss

C. Friction and windage loss

D. Hysteresis loss

Question ID : 8970323111
Status : Answered
Chosen Option : 1

Q.58 The function chart system of programming was originally developed in:
Ans A. South America

B. Asia

C. North America

D. Europe

Question ID : 8970323046
 Status : Not Answered
Chosen Option : --

Q.59 Electrodynamo meter type of instruments are enclosed in a casing made up of high
permeability material to:
Ans A. To remove electrostatic effects.

B. To provide mechanical strength to the coils present.

C. To protect against external magnetic fields.

D. Provide good damping.

Question ID : 8970323143
Status : Answered
Chosen Option : 3

Q.60

Ans A. Distribution fuse board with switches

B. Distribution fuse board without switches

C. Main fuse board with switches

D. Main fuse board without switches

Question ID : 8970323095
Status : Answered
Chosen Option : 2

Q.61

Ans A.

B.

C.

D.

Question ID : 8970323130
Status : Not Answered
 Chosen Option : --

Q.62 The most efficient power plant is ______.

Ans A. Hydro electric power plant

B. Coal- based steam power plant

C. Nuclear power plant

D. Diesel engine power plant

Question ID : 8970323087
Status : Answered
Chosen Option : 2

Q.63 This metal is used in high rupturing capacity fuses and in special contacts:
Ans A. Silver

B. Tin

C. Nickel

D. Zinc

Question ID : 8970323139
Status : Answered
Chosen Option : 1

Q.64 In Rod Gap Arrester, a current limiting resistance is connected in series with the rod in order
to ______.
Ans A. Increase the rod gap

B. Avoid cascading of steep fronted waves

C. Avoid continued sparking even at low voltage

D. Reduce breakdown voltage

Question ID : 8970323057
Status : Answered
Chosen Option : 3

Q.65 The first thermal power plant of India is:

Ans A. Mundhra Ultra Mega Power Plant

B. Hussain Sagar Thermal Power Station

C. Vindhyachal Thermal Power Station

D. Jharsuguda Thermal Power Plant

Question ID : 8970323090
Status : Not Answered
Chosen Option : --

Q.66 According to IE Rules the maximum load on a power sub circuit should not exceed ______
watts.
Ans A. 3000

B. 1000

C. 5000

D. 10000
 Question ID : 8970323098
Status : Answered
Chosen Option : 2

Q.67 An AC voltage of maximum value equal to 100V is applied to a single phase fully controlled
bridge circuit. The peak inverse voltage rating of each SCR used will be ______.
Ans A. 141.4V

B. 200V

C. 70.7V

D. 100V

Question ID : 8970323102
Status : Answered
Chosen Option : 1

Q.68 It is used in panels for switch gear and arcing device.

Ans A. Asbestos cement

B. Asbestos tapes

C. Asbestos paper and board with cotton backing

D. Asbestos cloth

Question ID : 8970323137
Status : Answered
Chosen Option : 3

Q.69 For a 16-bit signed integer, SLC 500 counters can count within the range of:
Ans A. -32,767 to +32,768

B. -32,765 to +32,764

C. -32,766 to +32,765

D. -32,768 to +32,767

Question ID : 8970323045
Status : Not Answered
Chosen Option : --

Q.70 An electromagnetic attraction type relay operates on ______.

Ans A. Pulsated DC

B. AC only

C. DC only

D. Both AC & DC

Question ID : 8970323052
Status : Answered
Chosen Option : 4

Q.71 The hydraulic turbine suitable for a speed range of 95 to 440 rpm is:
Ans A. Pelton wheel

B. Kaplan
 C. Rankine

D. Francis

Question ID : 8970323084
Status : Not Answered
Chosen Option : --

Q.72

Ans A. Meter distribution board

B. Meter installation board

C. Meter generation board

D. Meter transmission board

Question ID : 8970323101
Status : Answered
Chosen Option : 2

Q.73 The power transfer capability of a transmission line is the most affected by _______.
Ans A. Shunt conductance

B. Capacitance

C. Resistance

D. Inductance

Question ID : 8970323074
Status : Answered
Chosen Option : 4

Q.74 A universal motor has high starting torque and a variable speed characteristics because it is
______.
Ans A. Shunt wound

B. Long shunt wound

C. Compound wound

D. Series wound

Question ID : 8970323037
Status : Answered
Chosen Option : 4

Q.75 The short circuit ratio (SCR) of a synchronous machine is given by relation ______ under
 rated speed condition.
Ans A. Field current for rated OC current / Field current for rated SC voltage

B. Field current for rated SC current / Field current for rated OC voltage

C. Field current for rated SC voltage / Field current for rated OC current

D. Field current for rated OC voltage / Field current for rated SC current

Question ID : 8970323029
Status : Not Answered
Chosen Option : --

Q.76 A plant having load factor of 0.6 has a peak load of 100MW. The energy produced by this
plant for a month of 30 days is:
Ans A.

B.

C.

D.

Question ID : 8970323089
Status : Not Answered
Chosen Option : --

Q.77 The major advantage of a radial distribution system is:

Ans A. Less voltage fluctuations at the consumer's terminal

B. Low initial cost

C. Require less reserve capacity

D. Increased service reliability

Question ID : 8970323078
Status : Answered
Chosen Option : 2

Q.78 On light loads, induction type A.C motors works on power factor in the range of _______.
Ans A. 0.8-0.9

B. 0.2-0.3

C. 0.5-0.6

D. 0.6-0.8

Question ID : 8970323073
Status : Answered
Chosen Option : 2

Q.79 During air conditioning in winter:

Ans A. The air is cooled and dehumidified

B. The air is cooled and humidified.

C. The air is heated and humidified.

D. The air is heated and dehumidified.

Question ID : 8970323006
 Status : Answered
Chosen Option : 4

Q.80 If computers and monitors are set in ‘sleep’ mode when not in use, the energy cost is
reduced approximately by:
Ans A. 45 percent

B. 30 percent

C. 25 percent

D. 40 percent

Question ID : 8970323067
Status : Not Answered
Chosen Option : --

Q.81 The starter recommended for a 15 hp squirrel cage induction motor is:
Ans A. Star delta starter

B. Face plate starter

C. Direct one line starter

D. Auto transformer starter

Question ID : 8970323025
Status : Answered
Chosen Option : 1

Q.82 In a double squirrel cage motor, outer cage is made of high resistance metal bars primarily
for the purpose of increasing its ______.
Ans A. Starting torque

B. Speed regulation

C. Efficiency

D. Starting current

Question ID : 8970323034
Status : Answered
Chosen Option : 1

Q.83 The unit of solid angle is ______.

Ans A.

B. Steradian

C. Lumens/watt

D. Candela

Question ID : 8970323002
Status : Answered
Chosen Option : 2

Q.84
Ans A. Protective earth

B. Clean earth

C. Chassis earth

D. Neutral earth

Question ID : 8970323017
Status : Answered
Chosen Option : 1

Q.85 Which of the following is not a PLC manufacturer?

Ans A. SIEMENS

B. ALLEN BRADLEY

C. MICROSOFT

D. MITSUBISHI

Question ID : 8970323047
Status : Not Answered
Chosen Option : --

Q.86 In thermal power plants, the function of economizer is to:

Ans A. Heat steam from boiler

B. Heat feed water using flue gas

C. Heat air fuel mixture

D. Heat steam taken from turbine outlets

Question ID : 8970323082
Status : Answered
Chosen Option : 1

Q.87 During regenerative braking the motor operates as:

Ans A. Motor

B. Inverter

C. Transformer

D. Generator

Question ID : 8970323112
Status : Answered
Chosen Option : 4

Q.88 In oxide film arrester, when heated, lead peroxide gets converted to:
Ans A. Black lead
 B. White lead

C. Graphite

D. Red lead

Question ID : 8970323059
Status : Answered
Chosen Option : 2

Q.89

Ans A. 470V

B. 460V

C. 476V

D. 480V

Question ID : 8970323081
Status : Not Answered
Chosen Option : --

Q.90 The permissible voltage drop in a lighting circuit is ______.

Ans A. 5 % of the supply voltage – 1V

B. 3 % of the supply voltage

C. 2 % of the supply voltage + 1 V

D. 3 % of the supply voltage + 1 V

Question ID : 8970323013
Status : Not Answered
Chosen Option : --

Q.91 Which of the following magnetic materials have small area of hysteresis loop?
Ans A. Saturable magnetic material

B. Soft magnetic material

C. Hard magnetic material

D. Diamagnetic material

Question ID : 8970323136
Status : Answered
Chosen Option : 2

Q.92 The main circuit wire in a domestic installation is required to carry a current of 20A when
connected across a single phase supply voltage of 230V. The maximum permissible voltage
 drop can be ______.
Ans A. 4.5V

B. 5.6V

C. 11.5V

D. 10.5V

Question ID : 8970323014
Status : Answered
Chosen Option : 3

Q.93 A 2000/200 V, 20 kVA, 50Hz single phase transformer has 66 turns in the secondary
winding. The number of turns on primary will be ______.
Ans A. 550 turns

B. 440 turns

C. 330 turns

D. 660 turns

Question ID : 8970323118
Status : Answered
Chosen Option : 4

Q.94 Which of the following is the type of synthetic resin?

Ans A. Shellac

B. PVC

C. Wood resin

D. Amber

Question ID : 8970323135
Status : Not Answered
Chosen Option : --

Q.95

Ans A. Coasting

B. Free running

C. Acceleration on speed curve

D. Rheostatic acceleration

Question ID : 8970323004
 Status : Answered
Chosen Option : 3

Q.96

Ans A. 100V

B. 150V

C. 0V

D. 50V

Question ID : 8970323142
Status : Answered
Chosen Option : 2

Q.97

Ans A.

B.

C.

D.

Question ID : 8970323129
Status : Not Answered
Chosen Option : --

Q.98 Inverted operation of a generator can be protected using ______.

Ans A. Over frequency relay

B. Over speed relay

C. Reverse power relay

D. Overload relay

Question ID : 8970323054
Status : Answered
Chosen Option : 3

Q.99 An alternator is being synchronised to the power station bus bars whose frequency is 50 Hz.
 If the bulb of the synchroscope glows with maximum brightness, the frequency of the
alternator is:
Ans A. 50 Hz

B. 40 Hz

C. 55 Hz

D. 45 Hz

Question ID : 8970323148
Status : Answered
Chosen Option : 1

Q.100

Ans A. NAND

B. EX-OR

C. NOR

D. EX-NOR

Question ID : 8970323125
Status : Not Answered
Chosen Option : --

Q.101

Ans A. Ceiling Fan

B. Exhaust fan

C. Bracket Fan

D. Fan Regulator

Question ID : 8970323094
Status : Answered
Chosen Option : 2

Q.102 Three SCRs are connected together to form a series string. The voltages across the
thyristors are 350V, 300V and 250V respectively. If the currents in the thyristors are 6A, 9A,
and 12A respectively, what will be the value of equalising resistance to be used across each
thyristor?
Ans A.

B.
 C.

D.

Question ID : 8970323109
Status : Answered
Chosen Option : 4

Q.103 The lubricating oil used with sleeve bearings is to be renewed:

Ans A. Once in six months

B. Once in three months

C. Once in five months

D. Once in four months

Question ID : 8970323008
Status : Answered
Chosen Option : 2

Q.104 AND Function in ladder logic uses:

Ans A. Normally closed contacts in parallel

B. Normally closed contacts in series

C. Normally open contacts in series

D. Normally open contacts in parallel

Question ID : 8970323042
Status : Not Answered
Chosen Option : --

Q.105 Which of the following are the two 16 bit SFRs of Microcontroller 8051?
Ans A. PC, DPTR

B. SP, PSW

C. SP, DPTR

D. PC, SP

Question ID : 8970323051
Status : Not Answered
Chosen Option : --

Q.106 In synchronous motors, V-curves show relationship between:

Ans A. Armature current and supply voltage

B. DC field current and AC armature current

C. Excitation current and back emf

D. Field current and power factor

Question ID : 8970323040
Status : Answered
Chosen Option : 2

Q.107 ______ is used as power source in electric arc welding.

Ans A. DC Series generator
 B. Differentially wound compound generator

C. Separately excited DC generator

D. Cumulative compound DC generator

Question ID : 8970323001
Status : Answered
Chosen Option : 4

Q.108 A synchronous motor connected to infinite bus bars has at constant full load, 100%
excitation and unity power factor (p.f.). On changing the excitation only, the armature
current will have:
Ans A. Leading p.f. with under excitation

B. No change of p.f.

C. Lagging p.f. with over excitation

D. Leading p.f. with over excitation

Question ID : 8970323039
Status : Answered
Chosen Option : 4

Q.109 One of the basic parameters used by ASME to define fans is:
Ans A. Specific ratio

B. Impeller power

C. Static fan efficiency

D. Fan efficiency

Question ID : 8970323065
Status : Not Answered
Chosen Option : --

Q.110 The instrument used to measure illumination level is called:

Ans A. Wattmeter

B. Radiation pyrometer

C. Lux meter

D. Anemometer

Question ID : 8970323062
Status : Answered
Chosen Option : 3

Q.111

Ans A.

B.

C.
 D.

Question ID : 8970323061
Status : Not Answered
Chosen Option : --

Q.112 Identify the IC-74147.

Ans A. BCD to Decimal Decoder

B. Octal to Binary priority Encoder

C. Decimal to BCD priority Encoder

D. BCD to 7-Segment Decoder

Question ID : 8970323122
Status : Not Answered
Chosen Option : --

Q.113 Clamp on meters are used because:

Ans A. They help to measure very high voltages.

B. They are convenient to measure power dissipated in circuits.

C. They are very accurate

D. Using these meters it is possible to measure current flowing in a line without

breaking the circuit.

Question ID : 8970323146
Status : Answered
Chosen Option : 4

Q.114 The voltage between the feet of a person standing on the floor of substation with 0.5m
spacing between two feet during the flow of earth fault current is known as ______.
Ans A. Peak potential

B. Floor potential

C. Step potential

D. Touch potential

Question ID : 8970323056
Status : Not Answered
Chosen Option : --

Q.115 Hard ferrites are used for making ______.

Ans A. Light weight permanent magnet

B. Transformer cores

C. Electrical machinery

D. High frequency equipment

Question ID : 8970323133
Status : Answered
Chosen Option : 4

Q.116 The electric supply authority supplies power to the consumers through a low voltage three
 phase four wire distribution system is called ______.
Ans A. Primary transmission system

B. Primary distribution system

C. Secondary transmission system

D. Secondary distribution system

Question ID : 8970323100
Status : Answered
Chosen Option : 4

Q.117

Ans A. EX-OR Gate

B. AND Gate

C. NAND Gate

D. NOR Gate

Question ID : 8970323128
Status : Not Answered
Chosen Option : --

Q.118 OPC interfacing standard was developed during the years of:
Ans A. 1990s

B. 1960s

C. 1980s

D. 1970s

Question ID : 8970323044
Status : Not Answered
Chosen Option : --

Q.119 When an overhead connection is to be given to a single story building using G.I pipe, the
pipe is required to be supported by ______.
Ans A. Cross-arm

B. Stay wire

C. Clamps

D. Bird guards

Question ID : 8970323012
Status : Answered
Chosen Option : 2

Q.120 Which of the following condition takes place when the Microcontroller 8051 is reset?
Ans
 A. SP=08H, P1= 00H, RS0= 1, RS1= 1

B. SP=07H, P1= 00H, RS0= 0, RS1= 0

C. SP=08H, P1= FFH, RS0= 0, RS1= 0

D. SP=07H, P1= FFH, RS0= 0, RS1= 0

Question ID : 8970323048
Status : Not Answered
Chosen Option : --

Q.121 In a dual converter, if the firing angle of one bridge is 30°, then the firing angle of second
bridge is ______.
Ans A.

B.

C.

D.

Question ID : 8970323106
Status : Not Answered
Chosen Option : --

Q.122 In hydro-electric power plants, ______ reduces water hammer effect in penstock
Ans A. Spill way

B. Trash rack

C. Surge tank

D. Forebay

Question ID : 8970323083
Status : Not Answered
Chosen Option : --

Q.123 A power station has 4 consumers with their maximum demand as 40MW, 20MW, 30MW and
50MW. The maximum demand of the station is 100MW. The diversity factor of the plant is
______.
Ans A. 0.5

B. 0.2

C. 1.4

D. 0.35

Question ID : 8970323091
Status : Answered
Chosen Option : 3

Q.124

Ans A. 50 kHz

B. 200 kHz

C. 40 kHz

D. 33.33 kHz

Question ID : 8970323108
 Status : Not Answered
Chosen Option : --

Q.125 The range of frequency used for dielectric heating is:

Ans A. 10kHz to 5MHz

B. 500Hz to 5kHz

C. 5kHz to 10kHz

D. 10MHz to 30MHz

Question ID : 8970323003
Status : Answered
Chosen Option : 4

Q.126 Based on the type of rotor, the turbine used for vertical axis wind turbine is:
Ans A. Savonius type

B. Wound rotor type

C. Propeller type

D. Multiple blade type

Question ID : 8970323088
Status : Not Answered
Chosen Option : --

Q.127 In a single phase hysteresis motor, the rotor cylinder is made up of ______.
Ans A. Magnetically hard cobalt steel

B. Magnetically smooth chrome steel

C. Steel laminations

D. Solid steel

Question ID : 8970323038
Status : Answered
Chosen Option : 2

Q.128

Ans
A.

B.

C.

D.

Question ID : 8970323079
Status : Answered
Chosen Option : 1

Q.129 In the speed control of a slip ring induction motor using slip power recovery scheme ______.
Ans A. The efficiency increases but power factor decreases.

B. Efficiency improves and power factor remains constant.

 C. Power factor improves but efficiency decreases.

D. Both power factor and efficiency improve.

Question ID : 8970323110
Status : Answered
Chosen Option : 3

Q.130

Ans A. Negative edge triggering

B. Positive edge triggering

C. Positive level triggering

D. Negative level triggering

Question ID : 8970323124
Status : Not Answered
Chosen Option : --

Q.131 A factory hall of 80m X 25m is required to be illuminated with an illumination of 15 candle
per square meter using 120 lamps each having an efficiency of 15 lumens per watts.
Assuming an utilization factor and depreciation factor of 0.4 and 0.7 respectively, the
estimated wattage of lamps is ______.
Ans A. 200W

B. 60W

C. 100W

D. 40W

Question ID : 8970323019
Status : Not Answered
Chosen Option : --

Q.132 When subjected to short circuit, ______ conductor would experience maximum damage.
Ans A. Copper

B. Aluminium

C. A.C.S.R

D. Steel

Question ID : 8970323018
Status : Answered
Chosen Option : 4

Q.133 According to ECBC 2017, new buildings will be awarded ECBC plus status if they are able to
demonstrate an energy saving of:
 Ans A. 50 percent

B. 35 percent

C. 30 percent

D. 25 percent

Question ID : 8970323069
Status : Not Answered
Chosen Option : --

Q.134

Ans A.

B.

C.

D.

Question ID : 8970323126
Status : Not Answered
Chosen Option : --

Q.135

Ans A. 55.5 mV

B. 100 mV

C. 75 mV

D. 66.6 mV

Question ID : 8970323149
Status : Not Answered
Chosen Option : --

Q.136 Which of the following MOV instructions of Microcontroller 8051 will show an error, i.e.
Instruction is not valid?
Ans A. MOV 80H, 82H

B. MOV 80H, 90H

C. MOV 80H, 88H

D. MOV 80H, 92H

 Question ID : 8970323050
Status : Not Answered
Chosen Option : --

Q.137 ______ wiring is used in residential, commercial and public buildings to improve appearance.
Ans A. Conduit

B. Metal

C. Cleat

D. Batten

Question ID : 8970323093
Status : Answered
Chosen Option : 1

Q.138 In synchronous motors, the phenomenon of successive overshoots and under shoots in the
motor speed due to sudden changes in the load is called ______.
Ans A. Crawling

B. Humming

C. Hunting

D. Damping

Question ID : 8970323033
Status : Answered
Chosen Option : 3

Q.139 The minimum depth at which the pipe must be buried in pipe earthing is ______.
Ans A. 1.5 meters

B. 3.0 meters

C. 2.75 meters

D. 3.75 meters

Question ID : 8970323053
Status : Answered
Chosen Option : 4

Q.140

Ans A. 1.57 T

B. 1.5 T

C. 1.45 T

D. 1.35 T

Question ID : 8970323119
Status : Answered
Chosen Option : 2

Q.141 ______ voltages are caused by direct lightning strokes to the aerial lines in the high voltage
system.
Ans A. Stray
 B. Surge

C. Sag

D. Stress

Question ID : 8970323028
Status : Answered
Chosen Option : 2

Q.142

Ans A. Cathode ray oscilloscope

B. Digital frequency meter

C. Digital multimeter

D. Digital panelmeter

Question ID : 8970323150
Status : Not Answered
Chosen Option : --

Q.143 Which of the following is a Quad 2-Input OR Gate?

Ans A. 7432

B. 7400

C. 7486

D. 7408

Question ID : 8970323120
Status : Not Answered
Chosen Option : --

Q.144
 Ans A. Class D commutation

B. Class A commutation

C. Class C commutation

D. Class B commutation

Question ID : 8970323105
Status : Not Answered
Chosen Option : --

Q.145 Method of voltage control adopted for transmission lines in A.C systems is:
Ans A. Excitation control

B. Synchronous condenser

C. Booster transformers

D. Auto-transformer tap changing

Question ID : 8970323080
Status : Answered
Chosen Option : 4

Q.146 In order to improve the voltage regulation of a supply system, wires used in wiring the
system should have ______.
Ans A. High insulation resistance

B. More area of cross section

C. Less area of cross section

D. More specific resistance

Question ID : 8970323011
Status : Answered
Chosen Option : 3

Q.147 How many address inputs are required to access 256 Bytes memory?
Ans A. 256

B. 2

C. 8

D. 16
 Question ID : 8970323123
Status : Not Answered
Chosen Option : --

Q.148 Creeping in energy meter can be avoided by:

Ans A. Drilling two diametrically opposite holes in the disc.

B. Using adjustable resistance

C. Providing a small shading loop between the central pole of shunt magnet and the
disc.
D. Using shading bands around the central limb of shunt magnet

Question ID : 8970323144
Status : Answered
Chosen Option : 4

Q.149 Which of the following is not a standard Baud Rate?

Ans A. 1200

B. 9600

C. 4800

D. 2500

Question ID : 8970323049
Status : Not Answered
Chosen Option : --

Q.150 Which of the following is not an invalid BCD Code?

Ans A. 1011

B. 1010

C. 1001

D. 1100

Question ID : 8970323121
Status : Not Answered
Chosen Option : --

Section : General Knowledge_Awareness

Q.1 कस दे श ने अपनी रा य सरकार ारा आयो जत 'वाइ ट गुजरात स मट' जैसे नवेश काय म आयो जत करने
के लए भारत क मदद मांगी?
Ans A. उ बे क तान

B. अफ़ग़ा न तान

C. बां लादे श

D. क गज़ तान

Question ID : 8970323152
Status : Not Answered
Chosen Option : --

Q.2 अचनकमार-अमरकंटक बायो फ यर रजव न न ल खत रा य म थत है:

Ans A. स कम और म णपुर

B. म य दे श और छ ीसगढ़

C. असम और मजोरम

D. उ राखंड और उ र दे श

Question ID : 8970323162
Status : Not Answered
Chosen Option : --

Q.3 ______ का उपयोग समय के साथ रहने क लागत म प रवतन क नगरानी के लए कया जाता है।
Ans A. जीडीपी डफा टर

B. नमाता मू य सूचकांक (PPI)

C. पूरे ब मू य सूचकांक (WPI)

D. उपभो ा मू य सूचकांक (CPI)

Question ID : 8970323157
Status : Not Answered
Chosen Option : --

Q.4 स मशन क वफलता के बाद, ______ म भारत छोड़ो आंदोलन शु कया गया था:
Ans A. 1940

B. 1935

C. 1922

D. 1942

Question ID : 8970323165
Status : Answered
Chosen Option : 4

Q.5 न न ल खत म से कौन सा जीवमंडल भंडार ओ डशा म थत है?

Ans A. नोकरेक

B. नंदादे वी

C. समलीपाल

D. नील ग र

Question ID : 8970323164
Status : Not Answered
Chosen Option : --

Q.6 पग, वा कग, गालो पग और हाइपर ______ के कार ह:

Ans A. लागत सूचकांक

B. संप

C. मु ा फ त

D. वेतन

Question ID : 8970323156
Status : Not Answered
Chosen Option : --
Q.7 In computer terminology, ______ is an indication of how quickly data travels along a
connection.
Ans A. bandlength

B. bandwidth

C. bandarea

D. bandheight

Question ID : 8970323169
Status : Answered
Chosen Option : 2

Q.8 18 वां गुट नरपे आंदोलन (NAM) शखर स मेलन अ टू बर 2019 म ______ म आयो जत कया गया था।
Ans A. तुक

B. आज़रबाइजान

C. स

D. आम नया

Question ID : 8970323153
Status : Not Answered
Chosen Option : --

Q.9 द ण-पूव मज़ोरम रा य म थत मज़ो ह स को पहले _______ ह स कहा जाता था।

Ans A. लुशाई

B. नागा

C. डाफला

D. म मी

Question ID : 8970323161
Status : Not Answered
Chosen Option : --

Q.10 ______ क घोषणा 1940 म तीय व यु म भारतीय का समथन पाने के लए वायसराय लॉड लन लथगो
ारा क गई थी।
Ans A. दसंबर ऑफर

B. अग त ऑफर

C. माच ऑफर

D. जुलाई ऑफर

Question ID : 8970323166
Status : Not Answered
Chosen Option : --

Q.11 अग त 2019 म बैड मटन व च पयन शप का वण जीतने वाले पहले भारतीय कौन बने?
Ans A. पीवी सधु

B. वाला गु ा

C. अ नी पोन पा

D. साइना नेहवाल
 Question ID : 8970323154
Status : Answered
Chosen Option : 1

Q.12 भारत के सं वधान के भाग XV म अनु छे द 324 से 329 भारत के ______ से संबं धत है।
Ans A. क शा सत दे श

B. नवाचन णाली

C. मौ लक कत

D. मौ लक अ धकार

Question ID : 8970323159
Status : Answered
Chosen Option : 1

Q.13 The nickname given to Shoaib Akhtar is:

Ans A. The Turbanator

B. Flying Fish

C. Rawalpindi Express

D. The Don

Question ID : 8970323155
Status : Answered
Chosen Option : 3

Q.14 What is the full form of ADSL in computer terminology?

Ans A. Asymmetric Data Subscriber Line

B. Automatic Digital Subscriber Line

C. Asymmetric Digital Suspension Line

D. Asymmetric Digital Subscriber Line

Question ID : 8970323170
Status : Not Answered
Chosen Option : --

Q.15 1936 म लखनऊ (उ ) म आयो जत कां ेस अ धवेशन क अ य ता कसने क ?

Ans A. सुभाष चं बोस

B. जवाहर लाल नेह

C. फ़रोज़ शाह मेहता

D. महा मा गांधी

Question ID : 8970323167
Status : Answered
Chosen Option : 4

Q.16 भारत के सं वधान म न न ल खत म से कौन सी वशेषता संयु रा य अमे रका से ली गई है?

Ans A. मं य क कै बनेट णाली

B. मौ लक अ धकार

C. पंचवष य योजना
 D. रा प त के चुनाव क व ध

Question ID : 8970323158
Status : Answered
Chosen Option : 2

Q.17 भारत के सं वधान क _______ अनुसूची असम, मेघालय, पुरा और मजोरम म जनजातीय े के शासन
के लए वशेष ावधान दान करती है।
Ans A. दसव

B. सातव

C. यारहव

D. छठ

Question ID : 8970323160
Status : Answered
Chosen Option : 4

Q.18 काजीरंगा रा ीय उ ान थत है:

Ans A. असम

B. उ राखंड

C. ओ डशा

D. म य दे श

Question ID : 8970323163
Status : Answered
Chosen Option : 1

Q.19 कं यूटर श दावली म 'VDSL' के लए V या है?

Ans A. Very Low Resolution (वैरी लो रेसोलुशन)

B. Very High Resolution (वैरी हाई रेसोलुशन)

C. Very High Speed (वैरी हाई पीड)

D. Very Low Speed (वैरी लो पीड)

Question ID : 8970323168
Status : Answered
Chosen Option : 2

Q.20 अ टू बर 2019 म व ीय सुर ा पर दे श ारा उठाए गए नए उपाय के बाद, व ीय कारवाई काय बल (FATF)
क े ल ट से कस दे श को हटा दया गया है?
Ans A. ीलंका

B. इजराइल

C. लेबनान

D. बहामास

Question ID : 8970323151
Status : Not Answered
Chosen Option : --

Section : Reasoning
Q.1 उस वेन आरेख को पहचान जो दए गए आइटम वग को सबसे अ छ तरह से दशाता है।

लकड़ी, प थर, ट
Ans

A.

B.

C.

D.

Question ID : 8970323190
Status : Answered
Chosen Option : 4

Q.2 दनेश सोहन का भाई और मैरी का दामाद है। वेणु सोहन क बहन का पता है। वेणु क बहन के साथ दनेश का
या संबंध है?
Ans A. दामाद

B. भाई
 C. बेटा

D. प त

Question ID : 8970323184
Status : Answered
Chosen Option : 1

Q.3 Select the option that will correctly replace the question marks (?) in the series.

24, 39, 57, 78, ?

Ans A. 105

B. 102

C. 108

D. 106

Question ID : 8970323178
Status : Answered
Chosen Option : 2

Q.4 In a certain code CHAIR is written as 51031120 then in the same way how TUTOR will be
coded?
Ans A. 2224231720

B. 2224221720

C. 2224222720

D. 2223221720

Question ID : 8970323183
Status : Answered
Chosen Option : 4

Q.5 नीचे दया गया दो कथन का अनुसरण करता है। व ेषण कर और तय कर क दए गए कथन से का
उ र दया जा सकता है या नह ।

: क ा म सबसे ऊँचा कौन है?

कथन I: राम रोहन से नाटा और मोहन से ऊँचा है।

कथन II: मोहन क ऊँचाई रोहन और अनु से अ धक है।
Ans A. कथन I और II एक साथ पया त नह ह

B. केवल कथन II ही पया त है

C. कोई भी कथन I और II पया त ह

D. केवल कथन I ही पया त है

Question ID : 8970323174
Status : Answered
Chosen Option : 3

Q.6
Ans A.

B.

C.

D.

Question ID : 8970323171
Status : Answered
Chosen Option : 4

Q.7 उस वेन आरेख को पहचान जो दए गए आइटम वग को सबसे अ छ तरह से दशाता है।

हरण, भालू, तनपायी

Ans

A.

B.
 C.

D.

Question ID : 8970323189
Status : Answered
Chosen Option : 4

Q.8

Ans A. 63.75

B. 54.25

C. 61.5

D. 75.5
 Question ID : 8970323173
Status : Answered
Chosen Option : 4

Q.9 Select the option that will correctly replace the question marks (?) in the series.

9, 20, 42, 86, 174, ?

Ans A. 375

B. 350

C. 270 WWW.ALLEXAMREVIEW.COM
D. 289

Question ID : 8970323179
Status : Answered
Chosen Option : 2

Q.10 नीचे दया गया दो कथन का अनुसरण करता है। व ेषण कर और तय कर क दए गए कथन से का
उ र दया जा सकता है या नह ।

: या याम का ज म दन 26 जनवरी को है?

कथन I: याम का ज म 1996 म सोमवार के दन आ था।

कथन II: महीने म 31 दन ह।
Ans A. कथन I और II एक साथ पया त नह ह

B. केवल कथन I ही पया त है

C. कोई भी कथन I और II पया त ह

D. केवल कथन II ही पया त है

Question ID : 8970323175
Status : Answered
Chosen Option : 2

Q.11 Identify the Venn diagram that best represents the given item classes.

Students, Girls, Hockey Players

Ans

A.

WWW.ALLEXAMREVIEW.COM
 B.

C.

D.

Question ID : 8970323188
Status : Answered
Chosen Option : 4

Q.12 Select the option that will correctly replace the question marks (?) in the series.

M, O, R, V , ?
Ans A. Z

B. A

C. C

D. B

Question ID : 8970323176
Status : Answered
Chosen Option : 2
Q.13 नीचे दए गए दो कथन के बाद I और II लेबल के दो न कष ह। यह मानते ए क कथन क जानकारी सही है,
यह नणय ल क बयान म द गई जानकारी म से कौन सा न कष ता कक प से और न त प से अनुसरण
करता है।

कथन: सभी अंडे अप श ह।

सभी अप श भोजन ह।

न कष I: कुछ भोजन अप श ह।
न कष II: कुछ अप श अंडे ह।
Ans A. केवल न कष II अनुसरण करता है।

B. दोन न कष अनुसरण करते ह।

C. न तो न कष I और न ही न कष II अनुसरण करता है।

D. केवल न कष I अनुसरण करता है।

Question ID : 8970323185
Status : Answered
Chosen Option : 2

Q.14 उस वक प का चयन कर जो तीसरे श द से उसी तरह संबं धत है जैसे सरा श द पहले श द से संबं धत है।

प ी : च ड़याघर :: हवाई जहाज : ?

Ans A. मधुवा टका

B. सं हालय ( यू ज़यम)

C. वमानशाला

D. कारवां

Question ID : 8970323181
Status : Answered
Chosen Option : 3

Q.15

Ans A. 47

B. 44.6

C. 49

D. 56.3

Question ID : 8970323172
Status : Answered
Chosen Option : 2

Q.16 Which of the following interchange of signs would make the equation correct?

200 + 15 ÷ 6 × 9 – 29 = 181
Ans
 A. × and ÷

B. + and ÷

C. + and -

D. × and -

Question ID : 8970323180
Status : Answered
Chosen Option : 1

Q.17 उस वेन आरेख को पहचान जो दए गए आइटम वग को सबसे अ छ तरह से दशाता है।

वृ , झाड़ी, फल
Ans

A.

B.

C.
 D.

Question ID : 8970323187
Status : Answered
Chosen Option : 2

Q.18 Select the option that will correctly replace the question marks (?) in the series.

LG, NI, PL, RP, ?

Ans A. SU

B. TV

C. ST

D. TU

Question ID : 8970323177
Status : Answered
Chosen Option : 4

Q.19 उस वक प का चयन कर जो तीसरे श द से उसी तरह संबं धत है जैसे सरा श द पहले श द से संबं धत है।

उ : हसक :: उतरना : ?
Ans A. मर मत करना

B. पाबंद

C. नीचे आना

D. गव

Question ID : 8970323182
Status : Answered
Chosen Option : 3

Q.20 रेशमा का मुख द ण क ओर है, वह 90° पर बाएँ मुड़ती है और 300 m चलती है, फर वह बाएँ मुड़ती है और
50 m चलती है और दोबारा बाएँ मुड़ती है और 250 m चलती है और अंत म वह दाएँ मुड़ती है और 400 m
चलती है। उसका मुख अब कस दशा क ओर है?
Ans A. उ र

B. द ण

C. पूव

D. प म

Question ID : 8970323186
Status : Answered
Chosen Option : 1

Section : General Hindi

Q.1 सही पयायवाची समूह पहचा नए:

Ans A. तीर – इषु, शलीमुख

B. ध –पय, तोय

C. चाँदनी – श श, इं

D. कमल – नीरद, जलद

Question ID : 8970323193
Status : Answered
Chosen Option : 4

Q.2 ‘चरण कमल बंद ह रराई’ म अलंकार क पहचान कर:

Ans A. उ े ा

B. पक

C. ेष

D. यमक

Question ID : 8970323195
Status : Answered
Chosen Option : 2

Q.3 ‘गणतं ’ का वपरीताथक श द बताइए:

Ans A. परतं

B. राजतं

C. अ भजाततं

D. जातं

Question ID : 8970323192
Status : Answered
Chosen Option : 2

Q.4 दए गए प ांश के आधार पर के उ र द जए।

छ दक, उठ, ला नज वा जराज,

तज भय- व मय, सज शी साज।
सुन,मृ यु- वजय-अ भयान आज।
मेरा भात यह रा -याम।
ओ णभंगुर भव, राम राम!
वह ज म-मरण का मण-भाण,
म दे ख चुका ँ अप रमाण।
नवाण-हेतु मेरा याण;
या वात-वृ , या शीत-घाम।
ओ णभंगुर भव, राम राम।

क वता नायक कसे यागने का आ ान कर रहा है:

Ans A. भय- व मय

B. सुख-ऐ य

C. साज-स जा

D. शीत-घाम

Question ID : 8970323198
Status : Not Answered
Chosen Option : --
Q.5 ‘जहाँ खाना मु त मले’ के लए एक श द होगा:
Ans A. सदा त

B. भोजनालय

C. आ म

D. मं दर

Question ID : 8970323197
Status : Answered
Chosen Option : 3

Q.6 दए गए प ांश के आधार पर के उ र द जए।

छ दक, उठ, ला नज वा जराज,

तज भय- व मय, सज शी साज।
सुन,मृ यु- वजय-अ भयान आज!
मेरा भात यह रा -याम।
ओ णभंगुर भव, राम राम!
वह ज म-मरण का मण-भाण,
म दे ख चुका ँ अप रमाण।
नवाण-हेतु मेरा याण;
या वात-वृ , या शीत-घाम।
ओ णभंगुर भव, राम राम!

‘ णभंगुर भव’ का या अथ है?

Ans A. ण म न हो जाने वाला उ माद

B. ण म न हो जाने वाला संसार

C. ण म न हो जाने वाली भावना

D. ण म न हो जाने वाला वचार

Question ID : 8970323199
Status : Not Answered
Chosen Option : --

Q.7 ‘बाँधा था वधु को कसने इन काली जंज़ीर से।

म णवाले फ णय का मुख, य भरा आ हीर से’ म कौन सा अलंकार है?

Ans A. अ तशयो

B. संदेह

C. ांत

D. वरोधाभास

Question ID : 8970323194
Status : Answered
Chosen Option : 1

Q.8 दए गए प ांश के आधार पर के उ र द जए।

छ दक, उठ, ला नज वा जराज,

तज भय- व मय, सज शी साज।
सुन,मृ यु- वजय-अ भयान आज!
मेरा भात यह रा -याम।
ओ णभंगुर भव, राम राम!
वह ज म-मरण का मण-भाण,
म दे ख चुका ँ अप रमाण।
नवाण-हेतु मेरा याण;
या वात-वृ , या शीत-घाम।
 ओ णभंगुर भव, राम राम!

यह पं याँ कस ऐ तहा सक घटना का उ लेख कर रही है?

Ans A. गौतम बु के महा भ न मण का

B. पा डव के अ ातवास पर जाने का

C. राम के वन गमन का

D. महावीर वामी के गृह याग का

Question ID : 8970323200
Status : Not Answered
Chosen Option : --

Q.9 ‘ जसका कोई उ े य न हो’ श द समूह के लए एक श द बताइए:

Ans A. सउ े य

B. उ े य र हत

C. अनु े य

D. न े य

Question ID : 8970323196
Status : Answered
Chosen Option : 4

Q.10 व णुपद , जा वी, पथगा न न म से कसके पयायवाची श द है?

Ans A. गंगा

B. सर वती

C. यमुना WWW.ALLEXAMREVIEW.IN
D. नद

Question ID : 8970323191
Status : Not Answered
Chosen Option : --