Adiabatic Flame Temperature

Adiabatic Flame Temperature
For a combustion process that takes place adiabatically with no shaft work, the temperature of
the products is referred to as the adiabatic flame temperature. This is the maximum temperature
that can be achieved for given reactants. Heat transfer, incomplete combustion, and dissociation
all result in lower temperature. The maximum adiabatic flame temperature for a given fuel and
oxidizer combination occurs with a stoichiometric mixture (correct proportions such that all fuel
and all oxidizer are consumed). The amount of excess air can be tailored as part of the design to
control the adiabatic flame temperature. The considerable distance between present temperatures
in a gas turbine engine and the maximum adiabatic flame temperature at stoichiometric
conditions is shown in Figure 3.24(b), based on a compressor exit temperature of (922
K).
Figure 15.3: Schematic of adiabatic flame temperature
An initial view of the concept of adiabatic flame temperature is provided by examining two
reacting gases, at a given pressure, and asking what the end temperature is. The process is shown
schematically in Figure 15.3, where temperature is plotted versus the percentage completion of
the reaction. The initial state is and the final state is , with the final state at a higher
temperature than the initial state. The solid line in the figure shows a representation of the
``actual'' process.
To see how we would arrive at the final completion state the dashed lines break the state of
reaction change into two parts. Process (1) is reaction at constant and . To carry out such a
process, we would need to extract heat. Suppose the total amount of heat extracted per unit mass
is . The relation between the enthalpy changes in Process (1) is
where is the ``heat of reaction.''
For Process (2), we put this amount back into the products to raise their temperature to the final
level. For this process,
or, if we can approximate the specific heat as constant (using some appropriate average value)
For the overall process there is no work done and no heat exchanged so that the difference in
enthalpy between initial and final states is zero:
The temperature change during this second process is therefore given by (approximately)
(15..5)
The value of the adiabatic flame temperature given in Equation (15.5) is for 100% completion of
the reaction. In reality, as the temperature increases, the tendency is for the degree of reaction to
be less than 100%. For example, for the combustion of hydrogen and oxygen, at high
temperatures the combustion product (water) dissociates back into the simpler elemental
reactants. The degree of reaction is thus itself a function of temperature that needs to be
computed. We used this idea in discussing the stoichiometric ramjet, when we said that the
maximum temperature was independent of flight Mach number and hence of inlet stagnation
temperature. It is also to be emphasized that the idea of a constant (average) specific heat,
, is for illustration and not inherently part of the definition of adiabatic flame temperature.
An example computation of adiabatic flame temperature is furnished by the combustion of liquid

octane at with 400% theoretical air. The reaction is
For an adiabatic process
(15..6)
We can again think of the general process in steps:

1. Bring reactants to [the term ] from the initial temperature, using whatever
heat transfer, , is needed. In this example we do not need step (i) because we are
already at the reference temperature.
2. Reaction at [the term ]. There will be some heat transfer
in this step, , out of the combustor.
3. Put back heat into the products of combustion. The resulting temperature is the
adiabatic flame temperature.
In the present case Equation (15.6) is, explicitly:
We can examine the terms in the SFEE separately, starting with the heat of formation terms, and
keeping track of units:
The exit state at the adiabatic flame temperature is specified by:
We find the adiabatic flame temperature in three ways:
• an approximate solution using an average value of ,
• a more accurate one using the tabulated evolution of with temperature,

• or a more accurate solution using the tabulated values for gas enthalpy in Table A.8 of
SB&VW.
15.5.1 Approximate solution using ``average'' values of
specific heat
From Figure 15.2 we can use the values at 500 K as representative. These are:
Gas
(kJ/kmole)
45
35
30
30
Using ,
where
and using the exit state calculated above, find that
15.5.2 Solution for adiabatic flame temperature using

evolutions of specific heats with temperature
Tables give the following evolutions of specific heats with temperature:
Gas
Evolution of with (kJ/kmol)
Using
and the same equation as above, we obtain
15.5.3 Solution for adiabatic flame temperature using

tabulated values for gas enthalpy
28,041 21,924 19,246 18,221 kJ/kmole

33,405 25,978 22,707 21,460 kJ/kmole
Plugging in the numbers shows the answer is between these two conditions. Linearly
interpolating gives a value of

Adiabatic Flame Temperature

Uploaded by

Copyright:

Available Formats

Adiabatic Flame Temperature

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Adiabatic Flame Temperature

Uploaded by

Copyright:

Available Formats

Adiabatic Flame Temperature

Figure 15.3: Schematic of adiabatic flame temperature

is . The relation between the enthalpy changes in Process (1) is

where is the ``heat of reaction.''

An example computation of adiabatic flame temperature is furnished by the combustion of liquid

For an adiabatic process

We can again think of the general process in steps:

2. Reaction at [the term ]. There will be some heat transfer

in this step, , out of the combustor.

In the present case Equation (15.6) is, explicitly:

The exit state at the adiabatic flame temperature is specified by:

We find the adiabatic flame temperature in three ways:

• an approximate solution using an average value of ,

• a more accurate one using the tabulated evolution of with temperature,

and using the exit state calculated above, find that

15.5.2 Solution for adiabatic flame temperature using

and the same equation as above, we obtain

15.5.3 Solution for adiabatic flame temperature using

28,041 21,924 19,246 18,221 kJ/kmole

You might also like