Scope Location 1 CC-2319 P TEJ CALIBRATION CENTRE

Download as pdf or txt
Download as pdf or txt
You are on page 1of 64

Laboratory Name P.

TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,


AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 1 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Permanent Facility

1 ELECTRO- AC Current @ 50 Hz to 1 A to 10 A 0.16% to 0.25% Using Fluke 6 ½ DMM


TECHNICAL- 1 kHz Model 8846A by Direct
ELECTRICAL Relevant Standard /
EQUIPMENT Guideline IS 1248 –
(Measure) (Part 9), IS 13875 –
(Part 1 & 2)

2 ELECTRO- AC Current @ 50 Hz to 1 mA to 1 A 0.16% Using Fluke 6 ½ DMM


TECHNICAL- 1 kHz Model 8846A with C.T.
ELECTRICAL by Direct &
EQUIPMENT Comparison Method
(Measure) Relevant Standard /
Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

3 ELECTRO- AC Current @ 50 Hz to 100 µA to 1 mA 0.16% Using Fluke 6 ½ DMM


TECHNICAL- 1 kHz Model 8846A with C.T.
ELECTRICAL by Direct &
EQUIPMENT Comparison Method
(Measure) Relevant Standard /
Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

4 ELECTRO- AC High Voltage 1 kV to 40 kV 5.26% to 6.7% Using HV Probe with


TECHNICAL- DMM Direct Method
ELECTRICAL Relevant Standard /
EQUIPMENT Guideline IS 1248 –
(Measure) (Part 9), IS 13875 –
(Part 1 & 2)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 2 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
5 ELECTRO- AC Voltage @ 50 Hz to 1 V to 1000 V 0.11% Using Fluke 6½ DMM
TECHNICAL- 1 kHz Model 8846A by Direct
ELECTRICAL & Comparison Method
EQUIPMENT Relevant Standard /
(Measure) Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

6 ELECTRO- AC Voltage @ 50 Hz to 100 mV to 1 V 0.12% to 0.11% Using Fluke 6½ DMM


TECHNICAL- 1 kHz Model 8846A by Direct
ELECTRICAL & Comparison Method
EQUIPMENT Relevant Standard /
(Measure) Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

7 ELECTRO- Capacitance 1 nF to 100 µF 5.2% to 1.75% Using capacitance


TECHNICAL- Inductance @ 1kHz decade box with 8846A
ELECTRICAL (10µH to 1H) by Comparison Method
EQUIPMENT Relevant Standard /
(Measure) Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

8 ELECTRO- Current Ratio 1 A to 5 A 1.16% Using Multi Product


TECHNICAL- Error(Primary to Calibrator Fluke 5080A,
ELECTRICAL Secondary) 5A to 1A DMM 8846, MFC
EQUIPMENT Source Direct Method
(Measure) Relevant Standard /
Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 3 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
9 ELECTRO- Current Ratio 1 A to 20 A 0.72% Using Multi Product
TECHNICAL- Error(Primary/secondar Calibrator Fluke 5080A,
ELECTRICAL y) (20A/1A) DMM 8846, MFC
EQUIPMENT Source Direct Method
(Measure) Relevant Standard /
Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

10 ELECTRO- DC Current 1 A to 10 A 0.088% to 0.19% Using Fluke 6 ½ DMM


TECHNICAL- Model 8846A by Direct
ELECTRICAL & Comparison Method
EQUIPMENT Relevant Standard /
(Measure) Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

11 ELECTRO- DC Current 100 µA to 1 A 0.088% Using Fluke 6 ½ DMM


TECHNICAL- Model 8846A by Direct
ELECTRICAL & Comparison Method
EQUIPMENT Relevant Standard /
(Measure) Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

12 ELECTRO- DC High Voltage 1 kV to 40 kV 3.49% to 4.46% Using HV Probe with


TECHNICAL- DMM Direct Method
ELECTRICAL Relevant Standard /
EQUIPMENT Guideline IS 1248 –
(Measure) (Part 9), IS 13875 –
(Part 1 & 2)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 4 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
13 ELECTRO- DC Voltage 1 mV to 1000 V 0.41% to 0.01% Using Fluke 6 ½ DMM
TECHNICAL- Model 8846 A by Direct
ELECTRICAL & Comparison Method
EQUIPMENT Relevant Standard /
(Measure) Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

14 ELECTRO- Magnetic Field AC 100 Gauss to 2000 5.7% Using Gauss Meter by
TECHNICAL- Magnetic Field Gauss Direct/comparison
ELECTRICAL Method
EQUIPMENT
(Measure)

15 ELECTRO- Resistance/Insulation 1 M Ohms to 1 G 0.013% to 2.35% Using Fluke 6½ DMM


TECHNICAL- Ohms Model 8846A by Direct
ELECTRICAL & Comparison Method
EQUIPMENT Relevant Standard /
(Measure) Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

16 ELECTRO- Resistance/Insulation 1 Ohms to 1 M Ohms 0.36% to 0.013% Using Fluke 6½ DMM


TECHNICAL- Model 8846A by Direct
ELECTRICAL & Comparison Method
EQUIPMENT Relevant Standard /
(Measure) Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 5 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
17 ELECTRO- AC Current @ 50 Hz 20 A to 1000 A 0.82% to 1.1% Using Fluke 5080 MFC
TECHNICAL- with Coil by Direct
ELECTRICAL Method Relevant
EQUIPMENT (Source) Standard / Guideline IS
1248 – (Part 9), IS
13875 – (Part 1 & 2)

18 ELECTRO- AC Current @ 50 Hz 30 µA to 30 mA 3.2% to 0.29% Using Fluke 5080 MFC


TECHNICAL- with Coil by Direct
ELECTRICAL Method Relevant
EQUIPMENT (Source) Standard / Guideline IS
1248 – (Part 9), IS
13875 – (Part 1 & 2)

19 ELECTRO- AC Current @ 50 Hz to 10 A to 20 A 0.56% to 0.71% Using Fluke 5080 MFC


TECHNICAL- 1khz with Coil by Direct
ELECTRICAL Method Relevant
EQUIPMENT (Source) Standard / Guideline IS
1248 – (Part 9), IS
13875 – (Part 1 & 2)

20 ELECTRO- AC Current @ 50 Hz to 30 mA to 10 A 0.29% to 0.56% Using Fluke 5080 MFC


TECHNICAL- 1khz with Coil by Direct
ELECTRICAL Method Relevant
EQUIPMENT (Source) Standard / Guideline IS
1248 – (Part 9), IS
13875 – (Part 1 & 2)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 6 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
21 ELECTRO- AC Power @ 50 Hz 2.4 kW to 6 kW 0.77% to 0.83% Using Fluke 5080 MFC
TECHNICAL- (240V,10A) to Source with Coil Power
ELECTRICAL (600V,10A) by Direct Method
EQUIPMENT (Source) Relevant Standard /
Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

22 ELECTRO- AC Power @ 50 Hz 6 kW to 440 kW 0.83% to 1.03% Using Fluke 5080 MFC


TECHNICAL- (600V,10A) to Source with Coil Power
ELECTRICAL (440V,1000A) by Direct Method
EQUIPMENT (Source) Relevant Standard /
Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

23 ELECTRO- AC Power @ 50 Hz 4 W to 2.4 KW 0.4% to 0.77% Using Fluke 5080 MFC


TECHNICAL- (40V, 100mA) to Source with Coil Power
ELECTRICAL (240V,10A) by Direct Method
EQUIPMENT (Source) Relevant Standard /
Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

24 ELECTRO- AC Voltage @ 50 Hz to 1 mV to 300 mV 7.34% to 0.21% Using Fluke 5080 MFC


TECHNICAL- 1kHz by Direct Method
ELECTRICAL Relevant Standard /
EQUIPMENT (Source) Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 7 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
25 ELECTRO- AC Voltage @ 50 Hz to 300 mV to 300 V 0.21% to 0.18% Using Fluke 5080 MFC
TECHNICAL- 1kHz by Direct Method
ELECTRICAL Relevant Standard /
EQUIPMENT (Source) Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

26 ELECTRO- AC Voltage @ 50 Hz to 300 V to 1000 V 0.18% to 0.23% Using Fluke 5080 MFC
TECHNICAL- 1kHz by Direct Method
ELECTRICAL Relevant Standard /
EQUIPMENT (Source) Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

27 ELECTRO- DC Current 1 µA to 1 mA 11.63% to 0.11% Using Fluke 5080 MFC


TECHNICAL- with Coil by Direct
ELECTRICAL Method Relevant
EQUIPMENT (Source) Standard / Guideline IS
1248 – (Part 9), IS
13875 – (Part 1 & 2)

28 ELECTRO- DC Current 1 A to 20 A 0.2% to 0.78% Using Fluke 5080 MFC


TECHNICAL- with Coil by Direct
ELECTRICAL Method Relevant
EQUIPMENT (Source) Standard / Guideline IS
1248 – (Part 9), IS
13875 – (Part 1 & 2)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 8 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
29 ELECTRO- DC Current 1 mA to 100 mA 0.11% to 0.06% Using Fluke 5080 MFC
TECHNICAL- with Coil by Direct
ELECTRICAL Method Relevant
EQUIPMENT (Source) Standard / Guideline IS
1248 – (Part 9), IS
13875 – (Part 1 & 2)

30 ELECTRO- DC Current 100 mA to 1 A 0.06% to 0.2% Using Fluke 5080 MFC


TECHNICAL- with Coil by Direct
ELECTRICAL Method Relevant
EQUIPMENT (Source) Standard / Guideline IS
1248 – (Part 9), IS
13875 – (Part 1 & 2)

31 ELECTRO- DC Current 20 A to 1000 A 0.78% to 0.97% Using Fluke 5080 MFC


TECHNICAL- with Coil by Direct
ELECTRICAL Method Relevant
EQUIPMENT (Source) Standard / Guideline IS
1248 – (Part 9), IS
13875 – (Part 1 & 2)

32 ELECTRO- DC Power(15V,100mA) 1.5 W to 12 kW 0.2% to 0.63% Using Fluke 5080 MFC


TECHNICAL- to (600V,20A) by Direct Method
ELECTRICAL Relevant Standard /
EQUIPMENT (Source) Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 9 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
33 ELECTRO- DC Voltage 1 mV to 10 V 1.17% to 0.031% Using Fluke 5080 MFC
TECHNICAL- by Direct Method
ELECTRICAL Relevant Standard /
EQUIPMENT (Source) Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

34 ELECTRO- DC Voltage 10 V to 1000 V 0.031% to 0.0042% Using Fluke 5080 MFC


TECHNICAL- by Direct Method
ELECTRICAL
EQUIPMENT (Source)

35 ELECTRO- Low Resistance 10 µ Ohms to 1 Ohm 5.16% to 0.18% Using Decade Box by
TECHNICAL- discrete (10 µohm, 50 Direct Method Relevant
ELECTRICAL µohm, 100 µohm, 1 Standard / Guideline IS
EQUIPMENT (Source) mohm, 10 mohm, 100 1248 – (Part 9), IS
mohm, 1 ohm) 13875 – (Part 1 & 2)

36 ELECTRO- Power Factor @ 50 0.1 Lead 0.07PF Using Fluke 5080 MFC
TECHNICAL- Hz(40 V, 100 mA) to by Direct Method
ELECTRICAL (400 V, 10 A) Relevant Standard /
EQUIPMENT (Source) Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

37 ELECTRO- Power Factor @ 50 0.1 PF Lag 0.07PF Using Fluke 5080 MFC
TECHNICAL- Hz(40 V, 100 mA) to by Direct Method
ELECTRICAL (400 V, 10 A) Relevant Standard /
EQUIPMENT (Source) Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 10 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
38 ELECTRO- Power Factor @ 50 1 UPF 0.07PF Using Fluke 5080 MFC
TECHNICAL- Hz(40 V, 100 mA) to by Direct Method
ELECTRICAL (400 V, 10 A) Relevant Standard /
EQUIPMENT (Source) Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

39 ELECTRO- Resistance 1 Ohms to 19 M Ohms 1.16% to 0.12% Using Fluke 5080 MFC
TECHNICAL- Decade Resistance
ELECTRICAL Box by Direct Method
EQUIPMENT (Source)

40 ELECTRO- Resistance 19 M Ohms to 190 M 0.12% to 0.41% Using Fluke 5080 MFC
TECHNICAL- Ohms Decade Resistance
ELECTRICAL Box by Direct Method
EQUIPMENT (Source) Relevant Standard /
Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

41 ELECTRO- Resistance Discrete 200 M Ohms to 1 G 6% Using Zeal Discrete


TECHNICAL- (200M, 500M, 1Gohm) Ohms Decade Resistance
ELECTRICAL Box (200M, 500M, and
EQUIPMENT (Source) 1Gohm) by Direct
Method Relevant
Standard / Guideline IS
1248 – (Part 9), IS
13875 – (Part 1 & 2)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 11 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
42 ELECTRO- Thermocouple - 200 °C to 1370 °C 1.37°C Using Multifunction
TECHNICAL- TypeK–Type Calibrator by
TEMPERATURE Direct/Simulation
SIMULATION method Relevant
(Measure) Standard / Guideline
Euromet Guide – CG-
11

43 ELECTRO- ThermocoupleB–Type 600 °C to 1800 °C 4.58°C Using Multifunction


TECHNICAL- Calibrator by
TEMPERATURE Direct/Simulation
SIMULATION method Relevant
(Measure) Standard / Guideline
Euromet Guide – CG-
11

44 ELECTRO- ThermocoupleE–Type -200 °C to 1000 °C 1.16°C Using Multifunction


TECHNICAL- Calibrator by
TEMPERATURE Direct/Simulation
SIMULATION method Relevant
(Measure) Standard / Guideline
Euromet Guide – CG-
11

45 ELECTRO- ThermocoupleJ–Type -200 °C to 1200 °C 1.28°C Using Multifunction


TECHNICAL- Calibrator by
TEMPERATURE Direct/Simulation
SIMULATION method Relevant
(Measure) Standard / Guideline
Euromet Guide – CG-
11

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 12 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
46 ELECTRO- ThermocoupleN–Type -200 °C to 1300 °C 1.33°C Using Multifunction
TECHNICAL- Calibrator by
TEMPERATURE Direct/Simulation
SIMULATION method Relevant
(Measure) Standard / Guideline
Euromet Guide – CG-
11

47 ELECTRO- ThermocoupleRTD -200 °C to 800 °C 0.84°C Using Multifunction


TECHNICAL- sensor Calibrator by
TEMPERATURE Direct/Simulation
SIMULATION method Relevant
(Measure) Standard / Guideline
Euromet Guide – CG-
11

48 ELECTRO- ThermocoupleR–Type 0 °C to 1760 °C 4.6°C Using Multifunction


TECHNICAL- Calibrator by
TEMPERATURE Direct/Simulation
SIMULATION method Relevant
(Measure) Standard / Guideline
Euromet Guide – CG-
11

49 ELECTRO- ThermocoupleS–Type 0 °C to 1760 °C 4.55°C Using Multifunction


TECHNICAL- Calibrator by
TEMPERATURE Direct/Simulation
SIMULATION method Relevant
(Measure) Standard / Guideline
Euromet Guide – CG-
11

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 13 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
50 ELECTRO- ThermocoupleT–Type -200 °C to 400 °C 0.95°C Using Multifunction
TECHNICAL- Calibrator by
TEMPERATURE Direct/Simulation
SIMULATION method Relevant
(Measure) Standard / Guideline
Euromet Guide – CG-
11

51 ELECTRO- Thermocouple Type - 200 °C to 1370 °C 1.37°C Using Multifunction


TECHNICAL- K–Type Calibrator by Direct/
TEMPERATURE Simulation Method
SIMULATION (Source) Relevant Standard /
Guideline Euromet
Guide – CG-11

52 ELECTRO- ThermocoupleB–Type 600 °C to 1800 °C 4.58°C Using Multifunction


TECHNICAL- Calibrator by Direct/
TEMPERATURE Simulation Method
SIMULATION (Source) Relevant Standard /
Guideline Euromet
Guide – CG-11

53 ELECTRO- ThermocoupleE–Type -200 °C to 1000 °C 1.16°C Using Multifunction


TECHNICAL- Calibrator by Direct/
TEMPERATURE Simulation Method
SIMULATION (Source) Relevant Standard /
Guideline Euromet
Guide – CG-11

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 14 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
54 ELECTRO- ThermocoupleJ–Type -200 °C to 1200 °C 1.28°C Using Multifunction
TECHNICAL- Calibrator by Direct/
TEMPERATURE Simulation Method
SIMULATION (Source) Relevant Standard /
Guideline Euromet
Guide – CG-11

55 ELECTRO- ThermocoupleN–Type -200 °C to 1300 °C 1.33°C Using Multifunction


TECHNICAL- Calibrator by Direct/
TEMPERATURE Simulation Method
SIMULATION (Source) Relevant Standard /
Guideline Euromet
Guide – CG-11

56 ELECTRO- ThermocoupleRTD -200 °C to 800 °C 0.84°C Using Multifunction


TECHNICAL- sensor Calibrator by Direct/
TEMPERATURE Simulation Method
SIMULATION (Source) Relevant Standard /
Guideline Euromet
Guide – CG-11

57 ELECTRO- ThermocoupleR–Type 0 °C to 1760 °C 4.6°C Using Multifunction


TECHNICAL- Calibrator by Direct/
TEMPERATURE Simulation Method
SIMULATION (Source) Relevant Standard /
Guideline Euromet
Guide – CG-11

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 15 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
58 ELECTRO- ThermocoupleS–Type 0 °C to 1760 °C 4.55°C Using Multifunction
TECHNICAL- Calibrator by Direct/
TEMPERATURE Simulation Method
SIMULATION (Source) Relevant Standard /
Guideline Euromet
Guide – CG-11

59 ELECTRO- ThermocoupleT–Type -200 °C to 400 °C 0.95°C Using Multifunction


TECHNICAL- Calibrator by Direct/
TEMPERATURE Simulation Method
SIMULATION (Source) Relevant Standard /
Guideline Euromet
Guide – CG-11

60 ELECTRO- Frequency 10 Hz to 100 kHz 0.034% Using Fluke 6 ½ DMM


TECHNICAL- TIME & Model 8846A by Direct
FREQUENCY & Comparison Method
(Measure) Relevant Standard /
Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

61 ELECTRO- Frequency 100 kHz to 1000 kHz 0.034% to 0.012% Using Fluke 6 ½ DMM
TECHNICAL- TIME & Model 8846A by Direct
FREQUENCY & Comparison Method
(Measure) Relevant Standard /
Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 16 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
62 ELECTRO- Timer/Stop WatchHour 1 s to 24 Hr 0.26s to 7.6s Using /Digital Stop
TECHNICAL- TIME & Meter/ Time Interval Watch Measure & Time
FREQUENCY Meter Interval Meter by
(Measure) Comparison Method
Relevant Standard /
Guideline NIST 960-12

63 ELECTRO- Frequency @ 3V 1 kHz to 2 MHz 0.02% to 2.35% Using Fluke 5080 MFC,
TECHNICAL- TIME & Function Generator by
FREQUENCY (Source) Direct Method Relevant
Standard / Guideline IS
1248 – (Part 9), IS
13875 – (Part 1 & 2)

64 ELECTRO- Frequency @ 3V 2 Hz to 45 Hz 1.74% to 0.02% Using Fluke 5080 MFC,


TECHNICAL- TIME & Function Generator by
FREQUENCY (Source) Direct Method Relevant
Standard / Guideline IS
1248 – (Part 9), IS
13875 – (Part 1 & 2)

65 ELECTRO- Frequency @ 3V 45 Hz to 1 kHz 0.02% Using Fluke 5080 MFC,


TECHNICAL- TIME & Function Generator by
FREQUENCY (Source) Direct Method Relevant
Standard / Guideline IS
1248 – (Part 9), IS
13875 – (Part 1 & 2)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 17 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
66 MECHANICAL- VIBRATION 14 m/s2 peak to at one 6.2% Using Standard
ACCELERATION AND AMPLITUDEVIBRATIO spot value only Vibration Calibrator &
SPEED N ANALYZER/ Analyzer By Direct
VIBRATION METER Comparison Method
MULTIPOINT
ACCELERATION @10
Hz to 1280 Hz(0.1 g to
10 g )

67 MECHANICAL- VIBRATION 0.03 mm peak to peak 3.0% to 2.3% Using Standard


ACCELERATION AND AMPLITUDEVIBRATIO to 0.18 mm peak to Vibration Calibrator &
SPEED N ANALYZER/ peak Analyzer By Direct
VIBRATION METER Comparison Method
MULTIPOINT
DISPLACEMENT @10
Hz to 1280 Hz

68 MECHANICAL- VIBRATION 1 mm/s rms to 70 mm/s 6.5% to 3.1% Using Standard


ACCELERATION AND AMPLITUDEVIBRATIO rms Vibration Calibrator &
SPEED N ANALYZER/ Analyzer By Direct
VIBRATION METER Comparison Method
MULTIPOINT
VELOCITY @10 Hz to
1280 Hz

69 MECHANICAL- Sound Level Meter @ 1 94 dB to 114 dB 0.73dB Using Sound Level


ACOUSTICS kHz Calibrator

70 MECHANICAL- A. Plain Snap Gauges 3 mm to 300 mm 3.7µm Using Slip Gauge ,


DIMENSION (BASIC Relevant Standard /
MEASURING Guideline - IS-7876, IS-
INSTRUMENT, 3477, IS-8023 , IS-
GAUGE ETC.) 3455

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 18 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
71 MECHANICAL- B. Go & No Go Snap 3 mm to 250 mm 3.7µm Using Slip Gauge ,
DIMENSION (BASIC gauges Relevant Standard /
MEASURING Guideline - IS-7876, IS-
INSTRUMENT, 3477, IS-8023 , IS-
GAUGE ETC.) 3455

72 MECHANICAL- Bore Gauge (For 0 mm to 1 mm 2.9µm Using Electronic Dial


DIMENSION (BASIC Travel Only) Tester , Relevant
MEASURING Standard / Guidline -
INSTRUMENT, JIS B 7515
GAUGE ETC.)

73 MECHANICAL- Bore Gauge (For 1 mm to 2 mm 2.9µm Using Electronic Dial


DIMENSION (BASIC Travel Only) Tester, Relevant
MEASURING Standard / Guidline -
INSTRUMENT, JIS B 7515
GAUGE ETC.)

74 MECHANICAL- C. Single ended 3 mm to 160 mm 3.7µm Using Slip Gauge ,


DIMENSION (BASIC progressive type plate Relevant Standard /
MEASURING snap gauge Guideline - IS-7876, IS-
INSTRUMENT, 3477, IS-8023 , IS-
GAUGE ETC.) 3455

75 MECHANICAL- Coating Thickness 10 µm to 710 µm 4.6 µm to 22.4 µm Using Foils IS 12554


DIMENSION (BASIC Gauge
MEASURING
INSTRUMENT,
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 19 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
76 MECHANICAL- Combination SetBevel 0 deg to 90 deg 7.1min Using Angle Gauge,
DIMENSION (BASIC ProtectorLC 0.01 min Relevant Standard /
MEASURING Guideline - IS-4239
INSTRUMENT,
GAUGE ETC.)

77 MECHANICAL- Depth Micrometer LC 0 mm to 300 mm 11.7µm Using Slip gauges/


DIMENSION (BASIC 0.001 mm Surface plate, Relevant
MEASURING Standard / Guideline -
INSTRUMENT, BS - 6468
GAUGE ETC.)

78 MECHANICAL- Depth Vernier Caliper 0 mm to 300 mm 15.0µm Using Slip Gauge/


DIMENSION (BASIC LC 0.01 mm Caliper Checker /
MEASURING Length Bar ,Relevant
INSTRUMENT, Standard / Guideline -
GAUGE ETC.) IS 4213

79 MECHANICAL- Depth Vernier Caliper 0 mm to 600 mm 25.0µm Using Slip Gauge/


DIMENSION (BASIC LC 0.02mm Caliper Checker /
MEASURING Length Bar , Relevant
INSTRUMENT, Standard / Guideline -
GAUGE ETC.) IS 4213

80 MECHANICAL- Dial Indicator - Lever lc 0 mm to 1 mm 3.6µm Using Electronic Dial


DIMENSION (BASIC 0.001 mm Tester, Relevant
MEASURING Standard / Guideline -
INSTRUMENT, IS-11498
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 20 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
81 MECHANICAL- Dial Indicators - 0 mm to 25 mm 3.6µm Using Electronic Dial
DIMENSION (BASIC Plunger lc 0.001 mm Calibration Tester,
MEASURING Relevant Standard /
INSTRUMENT, Guideline - IS-2092
GAUGE ETC.)

82 MECHANICAL- Dial Indicators - 0 mm to 100 mm 3.6µm Using Electronic Dial


DIMENSION (BASIC Plunger lc 0.01 mm Calibration Tester, Slip
MEASURING gauge,Relevant
INSTRUMENT, Standard / Guideline -
GAUGE ETC.) IS-2092

83 MECHANICAL- Dial Indicators - 0 mm to 50 mm 3.6µm Using Electronic Dial


DIMENSION (BASIC Plunger lc 0.01 mm Calibration Tester, Slip
MEASURING gauge,Relevant
INSTRUMENT, Standard / Guideline -
GAUGE ETC.) IS-2092

84 MECHANICAL- Dial Thickness Gauge 0 mm to 50 mm 8.7µm Using Slip gauge


DIMENSION (BASIC lc 0.01 mm
MEASURING
INSTRUMENT,
GAUGE ETC.)

85 MECHANICAL- Dial Thickness Gauge 0 mm to 25 mm 4.1µm Using Slip gauge


DIMENSION (BASIC LC 0.001 mm
MEASURING
INSTRUMENT,
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 21 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
86 MECHANICAL- Dig Height Gauge lc 0 mm to 300 mm 13.0µm Using Caliper Checker/
DIMENSION (BASIC 0.01 mm Surface Plate ,Relevant
MEASURING Standard / Guideline -
INSTRUMENT, IS 2921
GAUGE ETC.)

87 MECHANICAL- Electronic Dial 0 mm to 25 mm 1.8µm using slip gauge


DIMENSION (BASIC Calibration Tester, Lc Standard / Guideline -
MEASURING 0.0001 mm IS-2092
INSTRUMENT,
GAUGE ETC.)

88 MECHANICAL- Electronic 0 mm to 25 mm 2.3 µm Using Slip Gauges


DIMENSION (BASIC Probe/Mechanical Dial
MEASURING Calibration Tester LC
INSTRUMENT, 0.0001 mm
GAUGE ETC.)

89 MECHANICAL- External Micrometer lc 1400 mm to 1600 mm 19.8µm Using Slip Gauges


DIMENSION (BASIC 0.01 mm Using Length Bar ,
MEASURING Relevant Standard /
INSTRUMENT, Guideline - IS 2967
GAUGE ETC.)

90 MECHANICAL- External Micrometer lc 300 mm to 600 mm 12.3µm Using Slip Gauges


DIMENSION (BASIC 0.01 mm Using Length Bar ,
MEASURING Relevant Standard /
INSTRUMENT, Guideline - IS 2967
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 22 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
91 MECHANICAL- External Micrometer LC 0 mm to 300 mm 11.6µm Using Slip Gauges
DIMENSION (BASIC 0.001 mm Using Length Bar ,
MEASURING Relevant Standard /
INSTRUMENT, Guideline - IS 2967
GAUGE ETC.)

92 MECHANICAL- External Micrometer LC 1000 mm to 1400 mm 13.2µm Using Slip Gauges


DIMENSION (BASIC 0.01 mm Using Length Bar ,
MEASURING Relevant Standard /
INSTRUMENT, Guideline - IS 2967
GAUGE ETC.)

93 MECHANICAL- External Micrometer LC 600 mm to 1000 mm 12.7µm Using Slip Gauges


DIMENSION (BASIC 0.01 mm Using Length Bar ,
MEASURING Relevant Standard /
INSTRUMENT, Guideline - IS 2967
GAUGE ETC.)

94 MECHANICAL- Feeler Gauge 0 mm to 2 mm 6.0µm Using Electronic probe


DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)

95 MECHANICAL- Foils 10 µm to 2 mm 6.0µm Using Electronic Probe


DIMENSION (BASIC
MEASURING
INSTRUMENT,
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 23 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
96 MECHANICAL- Inside Outside (Pistol) 0 mm to 50 mm 5.8µm Using Slip Gauge
DIMENSION (BASIC CaliperLC 10 µm
MEASURING
INSTRUMENT,
GAUGE ETC.)

97 MECHANICAL- Inside Outside (Pistol) 50 mm to 100 mm 57.7µm Using Slip Gauge


DIMENSION (BASIC CaliperLC 100 µm
MEASURING
INSTRUMENT,
GAUGE ETC.)

98 MECHANICAL- Internal Micrometer 50 mm to 600 mm 7.3µm Using Caliper


DIMENSION (BASIC Stick Micrometers LC checker/Length bar ,
MEASURING 0.01 mm Relevant Standard /
INSTRUMENT, Guideline - IS 2966
GAUGE ETC.)

99 MECHANICAL- Metric Steel Scale / 0 mm to 1000 mm 375.0µm Using Tape And Scale
DIMENSION (BASIC Shrinkage Scale Calibrator, Relevant
MEASURING Standard / Guideline -
INSTRUMENT, IS-1481
GAUGE ETC.)

100 MECHANICAL- Metric Steel 0 m to 200 m 375 µm xsqrt(L) L in m Using Tape And Scale
DIMENSION (BASIC Tapes/Woven Matallic Calibrator, Relevant
MEASURING & Glass Fiber Tape/ Standard / Guideline -
INSTRUMENT, Measuring Tape Steel IS-1269 & IS-1269
GAUGE ETC.) (Part-I)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 24 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
101 MECHANICAL- Micrometer Setting 1000 mm to 1600 mm 16.9µm Using Electronic Probe/
DIMENSION (BASIC RodsA. Flate EndedB. Length bar,Holding
MEASURING Round Ended fixture with caliper jaws
INSTRUMENT,
GAUGE ETC.)

102 MECHANICAL- Micrometer Setting 25 mm to 300 mm 7.1µm Using Slip Gauges/


DIMENSION (BASIC RodsA. Flate EndedB. Electronic Probe
MEASURING Round Ended
INSTRUMENT,
GAUGE ETC.)

103 MECHANICAL- Micrometer Setting 300 mm to 1000 mm 13.4µm Using Electronic Probe/
DIMENSION (BASIC RodsA. Flate EndedB. Length bar
MEASURING Round Ended
INSTRUMENT,
GAUGE ETC.)

104 MECHANICAL- Pie-Tape 0 to 50m 375 µm xsqrt(L) L in Using Tape And Scale
DIMENSION (BASIC meter Calibrator
MEASURING
INSTRUMENT,
GAUGE ETC.)

105 MECHANICAL- Plug Gauge(Plain/ 100 mm to 300 mm 4.0µm Using Slip Gauges
DIMENSION (BASIC Paddle/ OD Electronic Probe,
MEASURING Master/CylindricalSettin Relevant Standard /
INSTRUMENT, g Master/Pin Gauge) Guideline - IS-3455,IS-
GAUGE ETC.) 6137,IS-6244,IS-6246

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 25 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
106 MECHANICAL- Plug Gauge(Plain/ 1 mm to 100 mm 4.0µm Using Slip Gauges
DIMENSION (BASIC Paddle/ OD Master/Pin Electronic Probe,
MEASURING Gauge) Relevant Standard /
INSTRUMENT, Guideline - IS-3455,IS-
GAUGE ETC.) 6137,IS-6244,IS-6246

107 MECHANICAL- Surface Roughness Ra 1.60 µm to 2.97 µm 9.1% Using Surface


DIMENSION (BASIC Reference Standard Roughness Tester ,
MEASURING Relevant Standard /
INSTRUMENT, Guideline - IS-3073/IS-
GAUGE ETC.) 10707

108 MECHANICAL- Surface Roughness 1.60 Ra to 2.97 Ra 9.5% Using Precision


DIMENSION (BASIC Tester Reference Standard
MEASURING
INSTRUMENT,
GAUGE ETC.)

109 MECHANICAL- Test Sieves 4 mm to 100 mm 49.0µm Using Digital Vernier,


DIMENSION (BASIC Relevant Standard /
MEASURING Guideline - IS-460 (Part
INSTRUMENT, : I,II, & III)
GAUGE ETC.)

110 MECHANICAL- Ultra Sonic Thickness 0.5 mm to 100 mm 57.8µm Using Length Bar/Slip
DIMENSION (BASIC Gauge LC 0.01 mm Gauge
MEASURING
INSTRUMENT,
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 26 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
111 MECHANICAL- Vernier Caliper lc 0 mm to 300 mm 15.0µm Using Caliper Checker
DIMENSION (BASIC 0.01mm Relevant Standard /
MEASURING Guideline - IS 3651
INSTRUMENT, (Part-I & II)
GAUGE ETC.)

112 MECHANICAL- Vernier Calipers lc 0.01 300 mm to 600 mm 16.3µm Using Caliper Checker
DIMENSION (BASIC mm Relevant Standard /
MEASURING Guideline - IS 3651
INSTRUMENT, (Part-I & II)
GAUGE ETC.)

113 MECHANICAL- Vernier Calipers lc 0.02 0 mm to 1000 mm 26.0µm Using Length Bar,
DIMENSION (BASIC mm Relevant Standard /
MEASURING Guideline - IS 3651
INSTRUMENT, (Part-I, II, III)
GAUGE ETC.)

114 MECHANICAL- Vernier Calipers lc 0.02 0 mm to 1500 mm 28.0µm Using Length Bar,
DIMENSION (BASIC mm Relevant Standard /
MEASURING Guideline - IS 3651
INSTRUMENT, (Part-I, II, III)
GAUGE ETC.)

115 MECHANICAL- Vernier Calipers lc 0.02 0 mm to 2000 mm 31.0µm Using Length Bar,
DIMENSION (BASIC mm Relevant Standard /
MEASURING Guideline - IS 3651
INSTRUMENT, (Part-I, II, III)
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 27 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
116 MECHANICAL- Vernier Height Gauge 0 mm to 1000 mm 17.0µm Length Bar ,Relevant
DIMENSION (BASIC lc 0.02 mm Standard / Guideline -
MEASURING IS 2921
INSTRUMENT,
GAUGE ETC.)

117 MECHANICAL- Vernier Height Gauge 300 mm to 600 mm 17.0µm Using Caliper Checker/
DIMENSION (BASIC lc 0.02 mm Surface Plate ,Relevant
MEASURING Standard / Guideline -
INSTRUMENT, IS 2921
GAUGE ETC.)

118 MECHANICAL- Low Pressure Pressure (-) 350 mbar to 350 2.71mbar Using Digital
PRESSURE Gauges, Pressure mbar Manometer with
INDICATING DEVICES Transducer, Pressure uncertainty of 0.16
Transmitters, mbar and procedure
Magnahelic gauges & based on DKD-R 6-1
Manometers. guidelines.

119 MECHANICAL- PRESSURE 0 bar to 700 bar 0.16 bar Using Digital pressure
PRESSURE (HYDRAULIC) Digital & gauge with uncertainty
INDICATING DEVICES Dial Pressure Gauges of 0.126 bar, and the
& Pressure procedure based on
Transmitters. DKD-R 6-1 guidelines.

120 MECHANICAL- PRESSURE 0 bar to 10 bar 0.06 bar Using Digital pressure
PRESSURE (Hydraulic/ gauge with uncertainty
INDICATING DEVICES Pneumatic)Digital & of 0.0025 bar and
Dial Pressure GaugeS procedure based on
& Pressure DKD-R 6-1 guidelines.
Transmitters.

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 28 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
121 MECHANICAL- PRESSURE (Hyraulic 0 bar to 70 bar 0.17 bar Using Digital pressure
PRESSURE /Pneumatic)Digital & gauge with uncertainty
INDICATING DEVICES Dial Pressure Gauges of 0.013 bar and
& Pressure procedure based on
Transmitters. DKD-R 6-1 guidelines.

122 MECHANICAL- PRESSURE 0 bar to 2 bar 0.06 bar Using Digital


PRESSURE (PNEUMATIC)Digital & compound gauge with
INDICATING DEVICES Dial Pressure GaugeS uncertainty of 0.00032
& Pressure bar & procedure based
Transmitter. on DKD-R 6-1
guidelines.

123 MECHANICAL- VACUUMVacuum (-) 1 bar to 0 bar 0.06bar Using Digital


PRESSURE Gauges, Vacuum compound gauge with
INDICATING DEVICES Transmitters & uncertainty of 0.00032
Recorders bar and procedure
based on ISO
3567/ISO 27893
standards.

124 MECHANICAL- Volumetric Flasks & 1000 ml to 5000 ml 4.9 ml to 7.5 ml Using Electronic
VOLUME Graduated Measuring Weighing Balance
Cylinders. 0.01gand procedure
based on IS/ISO 4787.

125 MECHANICAL- Micro Pipettes 10 µl to 100 µl 1.90 µl Using Electronic


VOLUME weighing Balance with
readability of 0.01 mg
and procedure based
on ISO 8655 Part 6.

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 29 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
126 MECHANICAL- Micro Pipettes 100 µl to 1000 µl 2.0 µl Using Electronic
VOLUME weighing Balance with
readability of 0.01 mg
and procedure based
on ISO 8655 Part 6.

127 MECHANICAL- pipettes, Burettes 0.1 ml to 100 ml 2.0 µl to 40.0 µl Using Electronic
VOLUME Volumetric Flasks & weighing balance with
Graduated Measuring readability of 0.1g and
Cylinders. procedure based on
IS/ISO 4787.

128 MECHANICAL- Volumetric Flasks / 100 ml to 1000 ml 40.0 µl to 4.9 ml Using Electronic
VOLUME Graduated Measuring weighing Balance with
Cylinders. readability of 0.01g,
and procedure based
on IS/ISO 4787.

129 MECHANICAL- Electronic Weighing 1 mg to 80 g 0.03 mg Using Accuracy Class


WEIGHING SCALE Balance ( Class I & E1 Weight, comparison
AND BALANCE coarser)d = 0.01 mg method as per,
Relevant Standard /
Guideline - OIML R-76-
1

130 MECHANICAL- Electronic Weighing 1 mg to 220 g 0.40 mg Using E1 accuracy


WEIGHING SCALE Balance ( Class I & class weight, and
AND BALANCE coarser)d = 0.1 mg procedure based on
OIML R-76-1
guidelines.

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 30 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
131 MECHANICAL- Electronic Weighing 0 kg to 6 kg 0.12 g Using F1 accuracy
WEIGHING SCALE Balance ( Class II & class weight and pro
AND BALANCE coarser)d = 0.01 g edure based on OIML
R-76-1 guidelines.

132 MECHANICAL- Electronic Weighing 0 kg to 300 kg 58.0 g Using M1 accuracy


WEIGHING SCALE Balance ( Class III & class weight and
AND BALANCE coarser)d = 50.0 g procedure based on
OIML R-76-1
guidelines.

133 MECHANICAL- Electronic Weighing 0 g to 500 g 0.91 mg Using E1 accuracy


WEIGHING SCALE Balance (Class I & class weights and
AND BALANCE coarser)d = 0.1 mg procedure based on
OIML R-76-1

134 MECHANICAL- Elecyrojic Weighing 0 kg to 30 kg 3.6 g Using M1 accuracy


WEIGHING SCALE Balance ( Class III & class weight and
AND BALANCE coarser)d = 1.0 g proxedure based on
OIML R-76-1
guidelines.

135 MECHANICAL- Spring Balance 1 kg to 10 kg 1.2 g to 3.1 g Using F1 Class Weight


WEIGHING SCALE
AND BALANCE

136 MECHANICAL- Spring Balance 10 kg to 100 kg 3.1 g to 57.8 g Using M1 Class Weight
WEIGHING SCALE
AND BALANCE

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 31 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
137 MECHANICAL- Weight / MassF1 class 1g 0.017 mg Using E1 Accuracy
WEIGHTS and coarser Class Weight and
Electronic weighing
balance Balance with
redability of 0.01 mg.
Procedure based on
OIML R-111-1
guidelines.

138 MECHANICAL- Weight / MassF1 class 1 mg 0.01 mg Using E1 Accuracy


WEIGHTS and coarser Class Weight and
Electronic weighing
balance Balance with
redability of 0.01 mg.
Procedure based on
OIML R-111-1
guidelines.

139 MECHANICAL- Weight / MassF1 class 10 g 0.043 mg Using E1 Accuracy


WEIGHTS and coarser Class Weight and
Electronic weighing
balance Balance with
redability of 0.01 mg.
Procedure based on
OIML R-111-1
guidelines.

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 32 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
140 MECHANICAL- Weight / MassF1 class 10 mg 0.01 mg Using E1 Accuracy
WEIGHTS and coarser Class Weight and
Electronic weighing
balance Balance with
redability of 0.01 mg.
Procedure based on
OIML R-111-1
guidelines.

141 MECHANICAL- Weight / MassF1 class 100 g 0.14 mg Using E1 Accuracy


WEIGHTS and coarser Class Weight and
Electronic weighing
balance Balance with
redability of 0.1 mg.
Procedure based on
OIML R-111-1
guidelines.

142 MECHANICAL- Weight / MassF1 class 100 mg 0.01 mg Using E1 Accuracy


WEIGHTS and coarser Class Weight and
Electronic weighing
balance Balance with
redability of 0.01 mg.
Procedure based on
OIML R-111-1
guidelines.

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 33 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
143 MECHANICAL- Weight / MassF1 class 2g 0.027 mg Using E1 Accuracy
WEIGHTS and coarser Class Weight and
Electronic weighing
balance Balance with
redability of 0.01 mg.
Procedure based on
OIML R-111-1
guidelines.

144 MECHANICAL- Weight / MassF1 class 2 mg 0.01 mg Using E1 Accuracy


WEIGHTS and coarser Class Weight and
Electronic weighing
balance Balance with
redability of 0.01 mg.
Procedure based on
OIML R-111-1
guidelines.

145 MECHANICAL- Weight / MassF1 class 20 g 0.043 mg Using E1 Accuracy


WEIGHTS and coarser Class Weight and
Electronic weighing
balance Balance with
redability of 0.01 mg.
Procedure based on
OIML R-111-1
guidelines.

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 34 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
146 MECHANICAL- Weight / MassF1 class 20 mg 0.01 mg Using E1 Accuracy
WEIGHTS and coarser Class Weight and
Electronic weighing
balance Balance with
redability of 0.01 mg.
Procedure based on
OIML R-111-1
guidelines.

147 MECHANICAL- Weight / MassF1 class 200 g 0.36 mg Using E1 Accuracy


WEIGHTS and coarser Class Weight and
Electronic weighing
balance Balance with
redability of 0.1 mg.
Procedure based on
OIML R-111-1
guidelines.

148 MECHANICAL- Weight / MassF1 class 200 mg 0.01 mg Using E1 Accuracy


WEIGHTS and coarser Class Weight and
Electronic weighing
balance Balance with
redability of 0.01 mg.
Procedure based on
OIML R-111-1
guidelines.

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 35 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
149 MECHANICAL- Weight / MassF1 class 5g 0.03 mg Using E1 Accuracy
WEIGHTS and coarser Class Weight and
Electronic weighing
balance Balance with
redability of 0.01 mg.
Procedure based on
OIML R-111-1
guidelines.

150 MECHANICAL- Weight / MassF1 class 5 mg 0.01 mg Using E1 Accuracy


WEIGHTS and coarser Class Weight and
Electronic weighing
balance Balance with
redability of 0.01 mg.
Procedure based on
OIML R-111-1
guidelines.

151 MECHANICAL- Weight / MassF1 class 50 g 0.038 mg Using E1 Accuracy


WEIGHTS and coarser Class Weight and
Electronic weighing
balance Balance with
redability of 0.01 mg.
Procedure based on
OIML R-111-1
guidelines.

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 36 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
152 MECHANICAL- Weight / MassF1 class 50 mg 0.01 mg Using E1 Accuracy
WEIGHTS and coarser Class Weight and
Electronic weighing
balance Balance with
redability of 0.01 mg.
Procedure based on
OIML R-111-1
guidelines.

153 MECHANICAL- Weight / MassF1 class 500 mg 0.01 mg Using E1 Accuracy


WEIGHTS and coarser Class Weight and
Electronic weighing
balance Balance with
redability of 0.01 mg.
Procedure based on
OIML R-111-1
guidelines.

154 MECHANICAL- Weight/MassM1 class 1000 g 0.012 g Using F1 Accuracy


WEIGHTS and coarser Class Weight and
Electronic weighing
balance Balance with
redability of 0.01 g.
Procedure based on
OIML R-111-1
guidelines.

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 37 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
155 MECHANICAL- Weight/MassM1 class 10000 g 0.68 g Using M1 Accuracy
WEIGHTS and coarser Class Weight and
Electronic weighing
balance Balance with
redability of 1 g.
Procedure based on
OIML R-111-1
guidelines.

156 MECHANICAL- Weight/MassM1 class 2000 g 0.012 g Using F1 Accuracy


WEIGHTS and coarser Class Weight and
Electronic weighing
balance Balance with
redability of 0.01 g.
Procedure based on
OIML R-111-1
guidelines.

157 MECHANICAL- Weight/MassM1 class 20000 g 1.15 g Using M1 Accuracy


WEIGHTS and coarser Class Weight and
Electronic weighing
balance Balance with
redability of 1 g.
Procedure based on
OIML R-111-1
guidelines.

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 38 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
158 MECHANICAL- Weight/MassM1 class 500 g 0.006 g Using F1 Accuracy
WEIGHTS and coarser Class Weight and
Electronic weighing
balance Balance with
redability of 0.01 g.
Procedure based on
OIML R-111-1
guidelines.

159 MECHANICAL- Weight/MassM1 class 5000 g 0.018 g Using F1 Accuracy


WEIGHTS and coarser Class Weight and
Electronic weighing
balance Balance with
redability of 0.01 g.
Procedure based on
OIML R-111-1
guidelines.

160 THERMAL- SPECIFIC Calibration of Thermo 10 %RH to 95 %RH @ 0.92 %RH to 1.01 % Using Digital
HEAT & HUMIDITY Hygrometer / 10°C, @ 25°C, @ 45°C RH Temperature /Humidity
Temperature Humidity Indicator with Sensor
Indicator with by comparison Method
sensor/probe at in Humidity chamber.
permanent laboratory

161 THERMAL- SPECIFIC Digital Temperature 10 °C to 80 °C 0.37°C Using Digital


HEAT & HUMIDITY humidity Indicator, Temperature /Humidity
temperature humidity Indicator with Sensor
gauge with sensor or by comparison Method
probe in temperature humidity
chamber

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 39 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
162 THERMAL- Glass Thermometer -80 °C to 250 °C 1.86°C Using 4Wire RTD with
TEMPERATURE Calibration temperature Indicator
in ultra low liquid
temperature bath and
oil baths by comparison
Method

163 THERMAL- Non Contact 50 °C to 500 °C 4.15°C Using Standard Non


TEMPERATURE Pyrometer, IR Contact IR Pyrometer,
Thermometer and Block Body Source by
radiation sources, Comparison Method

164 THERMAL- Non Contact 500 °C to 1200 °C 7.26°C Using Standard Non
TEMPERATURE Pyrometer, IR Contact IR Pyrometer,
Thermometer and Block Body Source by
radiation sources, Comparison Method

165 THERMAL- RTD / Thermo couple/ 50 °C to 250 °C 0.83°C Using Single position
TEMPERATURE Temperature Indicator SSPRT with Oil bath by
with Sensor without comparison Method
sensor / Temperature Relevant Standard /
Gauges, Temperature Guideline Relevant
Transmitter with Standard / Guideline-
Sensor IS: 7358, EURAMET
cg-8, ASTM E220 13

166 THERMAL- RTD / Thermo couple/ -80 °C to 50 °C 0.83°C Using Single position
TEMPERATURE Temperature sensors Low Temperature
with or without Master Calibrator by
Indicator. comparison method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 40 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
167 THERMAL- Temperature sensors -80 °C to 400 °C 1.22°C Using RTD with
TEMPERATURE RTDs indicator with
traceability as master in
low temperature/oil
baths as source and a
PRT as DUC

168 THERMAL- Using Single position 250 °C to 1200 °C 2.17°C Using Dry Block
TEMPERATURE RTD / Thermo couple/ Calibrator by
Temperature Indicator comparison Method
with Sensor or without with master having
sensor / Temperature traceability and
Gauges, respective DUCs.

169 THERMAL- Using Single position 400°C to 1200°C 2.172°C Using Single position N
TEMPERATURE Temperature/ N type Type Thermocouple
Thermocouple with With Indicator by
Indicator/Dry Block comparison Method
Calibrator/ N type
Thermocouple with
data logger as DUC

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 41 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

1 ELECTRO- AC Current @ 50 Hz to 1 A to 10 A 0.16% to 0.25% Using Fluke 6 ½ DMM


TECHNICAL- 1 kHz Model 8846A by Direct
ELECTRICAL Relevant Standard /
EQUIPMENT Guideline IS 1248 –
(Measure) (Part 9), IS 13875 –
(Part 1 & 2)

2 ELECTRO- AC Current @ 50 Hz to 1 mA to 1 A 0.16% Using Fluke 6 ½ DMM


TECHNICAL- 1 kHz Model 8846A with C.T.
ELECTRICAL by Direct &
EQUIPMENT Comparison Method
(Measure) Relevant Standard /
Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

3 ELECTRO- AC Current @ 50 Hz to 100 µA to 1 mA 0.16% Using Fluke 6 ½ DMM


TECHNICAL- 1 kHz Model 8846A with C.T.
ELECTRICAL by Direct &
EQUIPMENT Comparison Method
(Measure) Relevant Standard /
Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

4 ELECTRO- AC High Voltage 1 kV to 40 kV 5.26% to 6.7% Using HV Probe with


TECHNICAL- DMM Direct Method
ELECTRICAL Relevant Standard /
EQUIPMENT Guideline IS 1248 –
(Measure) (Part 9), IS 13875 –
(Part 1 & 2)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 42 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

5 ELECTRO- AC Voltage @ 50 Hz to 1 V to 1000 V 0.11% Using Fluke 6½ DMM


TECHNICAL- 1 kHz Model 8846A by Direct
ELECTRICAL & Comparison Method
EQUIPMENT Relevant Standard /
(Measure) Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

6 ELECTRO- AC Voltage @ 50 Hz to 100 mV to 1 V 0.12% to 0.11% Using Fluke 6½ DMM


TECHNICAL- 1 kHz Model 8846A by Direct
ELECTRICAL & Comparison Method
EQUIPMENT Relevant Standard /
(Measure) Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

7 ELECTRO- Active / Reactive/ 45V/0.1 Ato 320 0.13% to 1.16% Using Power / Energy
TECHNICAL- ApparentPower / V/100A, 0.01 PF to Comparator Measure &
ELECTRICAL Energy (Three Phase UPF @ 50 Hz Comparison Relevant
EQUIPMENT /Single Phase) Standard / Guideline IS
(Measure) 13779, (Class 1 & 2) IS
14697 (Class 0.2 & 0.5)
IS 12346

8 ELECTRO- Capacitance 1 nF to 100 µF 5.2% to 1.75% Using capacitance


TECHNICAL- Inductance @ 1kHz decade box with 8846A
ELECTRICAL (10µH to 1H) by Comparison Method
EQUIPMENT Relevant Standard /
(Measure) Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 43 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

9 ELECTRO- Current Ratio 1 A to 5 A 1.16% Using Multi Product


TECHNICAL- Error(Primary to Calibrator Fluke 5080A,
ELECTRICAL Secondary) 5A to 1A DMM 8846, MFC
EQUIPMENT Source Direct Method
(Measure) Relevant Standard /
Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

10 ELECTRO- Current Ratio 1 A to 20 A 0.72% Using Multi Product


TECHNICAL- Error(Primary/secondar Calibrator Fluke 5080A,
ELECTRICAL y) (20A/1A) DMM 8846, MFC
EQUIPMENT Source Direct Method
(Measure) Relevant Standard /
Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

11 ELECTRO- DC Current 1 A to 10 A 0.088% to 0.19% Using Fluke 6 ½ DMM


TECHNICAL- Model 8846A by Direct
ELECTRICAL & Comparison Method
EQUIPMENT Relevant Standard /
(Measure) Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 44 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

12 ELECTRO- DC Current 100 µA to 1 A 0.088% Using Fluke 6 ½ DMM


TECHNICAL- Model 8846A by Direct
ELECTRICAL & Comparison Method
EQUIPMENT Relevant Standard /
(Measure) Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

13 ELECTRO- DC High Voltage 1 kV to 40 kV 3.49% to 4.46% Using HV Probe with


TECHNICAL- DMM Direct Method
ELECTRICAL Relevant Standard /
EQUIPMENT Guideline IS 1248 –
(Measure) (Part 9), IS 13875 –
(Part 1 & 2)

14 ELECTRO- DC Voltage 1 mV to 1000 V 0.41% to 0.01% Using Fluke 6 ½ DMM


TECHNICAL- Model 8846 A by Direct
ELECTRICAL & Comparison Method
EQUIPMENT Relevant Standard /
(Measure) Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

15 ELECTRO- Magnetic Field AC 100 Gauss to 2000 5.7% Using Gauss Meter by
TECHNICAL- Magnetic Field Gauss Direct/comparison
ELECTRICAL Method
EQUIPMENT
(Measure)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 45 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

16 ELECTRO- Resistance/Insulation 1 M Ohms to 1 G 0.013% to 2.35% Using Fluke 6½ DMM


TECHNICAL- Ohms Model 8846A by Direct
ELECTRICAL & Comparison Method
EQUIPMENT Relevant Standard /
(Measure) Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

17 ELECTRO- Resistance/Insulation 1 Ohms to 1 M Ohms 0.36% to 0.013% Using Fluke 6½ DMM


TECHNICAL- Model 8846A by Direct
ELECTRICAL & Comparison Method
EQUIPMENT Relevant Standard /
(Measure) Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

18 ELECTRO- AC Current @ 50 Hz 20 A to 1000 A 0.82% to 1.1% Using Fluke 5080 MFC


TECHNICAL- with Coil by Direct
ELECTRICAL Method Relevant
EQUIPMENT (Source) Standard / Guideline IS
1248 – (Part 9), IS
13875 – (Part 1 & 2)

19 ELECTRO- AC Current @ 50 Hz 30 µA to 30 mA 3.2% to 0.29% Using Fluke 5080 MFC


TECHNICAL- with Coil by Direct
ELECTRICAL Method Relevant
EQUIPMENT (Source) Standard / Guideline IS
1248 – (Part 9), IS
13875 – (Part 1 & 2)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 46 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

20 ELECTRO- AC Current @ 50 Hz to 10 A to 20 A 0.56% to 0.71% Using Fluke 5080 MFC


TECHNICAL- 1khz with Coil by Direct
ELECTRICAL Method Relevant
EQUIPMENT (Source) Standard / Guideline IS
1248 – (Part 9), IS
13875 – (Part 1 & 2)

21 ELECTRO- AC Current @ 50 Hz to 30 mA to 10 A 0.29% to 0.56% Using Fluke 5080 MFC


TECHNICAL- 1khz with Coil by Direct
ELECTRICAL Method Relevant
EQUIPMENT (Source) Standard / Guideline IS
1248 – (Part 9), IS
13875 – (Part 1 & 2)

22 ELECTRO- AC Power @ 50 Hz 2.4 kW to 6 kW 0.77% to 0.83% Using Fluke 5080 MFC


TECHNICAL- (240V,10A) to Source with Coil Power
ELECTRICAL (600V,10A) by Direct Method
EQUIPMENT (Source) Relevant Standard /
Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

23 ELECTRO- AC Power @ 50 Hz 6 kW to 440 kW 0.83% to 1.03% Using Fluke 5080 MFC


TECHNICAL- (600V,10A) to Source with Coil Power
ELECTRICAL (440V,1000A) by Direct Method
EQUIPMENT (Source) Relevant Standard /
Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 47 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

24 ELECTRO- AC Power @ 50 Hz 4 W to 2.4 KW 0.4% to 0.77% Using Fluke 5080 MFC


TECHNICAL- (40V, 100mA) to Source with Coil Power
ELECTRICAL (240V,10A) by Direct Method
EQUIPMENT (Source) Relevant Standard /
Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

25 ELECTRO- AC Voltage @ 50 Hz to 1 mV to 300 mV 7.34% to 0.21% Using Fluke 5080 MFC


TECHNICAL- 1kHz by Direct Method
ELECTRICAL Relevant Standard /
EQUIPMENT (Source) Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

26 ELECTRO- AC Voltage @ 50 Hz to 300 mV to 300 V 0.21% to 0.18% Using Fluke 5080 MFC
TECHNICAL- 1kHz by Direct Method
ELECTRICAL Relevant Standard /
EQUIPMENT (Source) Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

27 ELECTRO- AC Voltage @ 50 Hz to 300 V to 1000 V 0.18% to 0.23% Using Fluke 5080 MFC
TECHNICAL- 1kHz by Direct Method
ELECTRICAL Relevant Standard /
EQUIPMENT (Source) Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 48 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

28 ELECTRO- DC Current 1 µA to 1 mA 11.63% to 0.11% Using Fluke 5080 MFC


TECHNICAL- with Coil by Direct
ELECTRICAL Method Relevant
EQUIPMENT (Source) Standard / Guideline IS
1248 – (Part 9), IS
13875 – (Part 1 & 2)

29 ELECTRO- DC Current 1 A to 20 A 0.2% to 0.78% Using Fluke 5080 MFC


TECHNICAL- with Coil by Direct
ELECTRICAL Method Relevant
EQUIPMENT (Source) Standard / Guideline IS
1248 – (Part 9), IS
13875 – (Part 1 & 2)

30 ELECTRO- DC Current 1 mA to 100 mA 0.11% to 0.06% Using Fluke 5080 MFC


TECHNICAL- with Coil by Direct
ELECTRICAL Method Relevant
EQUIPMENT (Source) Standard / Guideline IS
1248 – (Part 9), IS
13875 – (Part 1 & 2)

31 ELECTRO- DC Current 100 mA to 1 A 0.06% to 0.2% Using Fluke 5080 MFC


TECHNICAL- with Coil by Direct
ELECTRICAL Method Relevant
EQUIPMENT (Source) Standard / Guideline IS
1248 – (Part 9), IS
13875 – (Part 1 & 2)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 49 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

32 ELECTRO- DC Current 20 A to 1000 A 0.78% to 0.97% Using Fluke 5080 MFC


TECHNICAL- with Coil by Direct
ELECTRICAL Method Relevant
EQUIPMENT (Source) Standard / Guideline IS
1248 – (Part 9), IS
13875 – (Part 1 & 2)

33 ELECTRO- DC Power(15V,100mA) 1.5 W to 12 kW 0.2% to 0.63% Using Fluke 5080 MFC


TECHNICAL- to (600V,20A) by Direct Method
ELECTRICAL Relevant Standard /
EQUIPMENT (Source) Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

34 ELECTRO- DC Voltage 1 mV to 10 V 1.17% to 0.031% Using Fluke 5080 MFC


TECHNICAL- by Direct Method
ELECTRICAL Relevant Standard /
EQUIPMENT (Source) Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

35 ELECTRO- DC Voltage 10 V to 1000 V 0.031% to 0.0042% Using Fluke 5080 MFC


TECHNICAL- by Direct Method
ELECTRICAL
EQUIPMENT (Source)

36 ELECTRO- Low Resistance 10 µ Ohms to 1 Ohm 5.16% to 0.18% Using Decade Box by
TECHNICAL- discrete (10 µohm, 50 Direct Method Relevant
ELECTRICAL µohm, 100 µohm, 1 Standard / Guideline IS
EQUIPMENT (Source) mohm, 10 mohm, 100 1248 – (Part 9), IS
mohm, 1 ohm) 13875 – (Part 1 & 2)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 50 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

37 ELECTRO- Power Factor @ 50 0.1 Lead 0.07PF Using Fluke 5080 MFC
TECHNICAL- Hz(40 V, 100 mA) to by Direct Method
ELECTRICAL (400 V, 10 A) Relevant Standard /
EQUIPMENT (Source) Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

38 ELECTRO- Power Factor @ 50 0.1 PF Lag 0.07PF Using Fluke 5080 MFC
TECHNICAL- Hz(40 V, 100 mA) to by Direct Method
ELECTRICAL (400 V, 10 A) Relevant Standard /
EQUIPMENT (Source) Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

39 ELECTRO- Power Factor @ 50 1 UPF 0.07PF Using Fluke 5080 MFC


TECHNICAL- Hz(40 V, 100 mA) to by Direct Method
ELECTRICAL (400 V, 10 A) Relevant Standard /
EQUIPMENT (Source) Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

40 ELECTRO- Resistance 1 Ohms to 19 M Ohms 1.16% to 0.12% Using Fluke 5080 MFC
TECHNICAL- Decade Resistance
ELECTRICAL Box by Direct Method
EQUIPMENT (Source)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 51 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

41 ELECTRO- Resistance 19 M Ohms to 190 M 0.12% to 0.41% Using Fluke 5080 MFC
TECHNICAL- Ohms Decade Resistance
ELECTRICAL Box by Direct Method
EQUIPMENT (Source) Relevant Standard /
Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

42 ELECTRO- Resistance Discrete 200 M Ohms to 1 G 6% Using Zeal Discrete


TECHNICAL- (200M, 500M, 1Gohm) Ohms Decade Resistance
ELECTRICAL Box (200M, 500M, and
EQUIPMENT (Source) 1Gohm) by Direct
Method Relevant
Standard / Guideline IS
1248 – (Part 9), IS
13875 – (Part 1 & 2)

43 ELECTRO- Thermocouple - 200 °C to 1370 °C 1.37°C Using Multifunction


TECHNICAL- TypeK–Type Calibrator by
TEMPERATURE Direct/Simulation
SIMULATION method Relevant
(Measure) Standard / Guideline
Euromet Guide – CG-
11

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 52 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

44 ELECTRO- ThermocoupleB–Type 600 °C to 1800 °C 4.58°C Using Multifunction


TECHNICAL- Calibrator by
TEMPERATURE Direct/Simulation
SIMULATION method Relevant
(Measure) Standard / Guideline
Euromet Guide – CG-
11

45 ELECTRO- ThermocoupleE–Type -200 °C to 1000 °C 1.16°C Using Multifunction


TECHNICAL- Calibrator by
TEMPERATURE Direct/Simulation
SIMULATION method Relevant
(Measure) Standard / Guideline
Euromet Guide – CG-
11

46 ELECTRO- ThermocoupleJ–Type -200 °C to 1200 °C 1.28°C Using Multifunction


TECHNICAL- Calibrator by
TEMPERATURE Direct/Simulation
SIMULATION method Relevant
(Measure) Standard / Guideline
Euromet Guide – CG-
11

47 ELECTRO- ThermocoupleN–Type -200 °C to 1300 °C 1.33°C Using Multifunction


TECHNICAL- Calibrator by
TEMPERATURE Direct/Simulation
SIMULATION method Relevant
(Measure) Standard / Guideline
Euromet Guide – CG-
11

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 53 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

48 ELECTRO- ThermocoupleRTD -200 °C to 800 °C 0.84°C Using Multifunction


TECHNICAL- sensor Calibrator by
TEMPERATURE Direct/Simulation
SIMULATION method Relevant
(Measure) Standard / Guideline
Euromet Guide – CG-
11

49 ELECTRO- ThermocoupleR–Type 0 °C to 1760 °C 4.6°C Using Multifunction


TECHNICAL- Calibrator by
TEMPERATURE Direct/Simulation
SIMULATION method Relevant
(Measure) Standard / Guideline
Euromet Guide – CG-
11

50 ELECTRO- ThermocoupleS–Type 0 °C to 1760 °C 4.55°C Using Multifunction


TECHNICAL- Calibrator by
TEMPERATURE Direct/Simulation
SIMULATION method Relevant
(Measure) Standard / Guideline
Euromet Guide – CG-
11

51 ELECTRO- ThermocoupleT–Type -200 °C to 400 °C 0.95°C Using Multifunction


TECHNICAL- Calibrator by
TEMPERATURE Direct/Simulation
SIMULATION method Relevant
(Measure) Standard / Guideline
Euromet Guide – CG-
11

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 54 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

52 ELECTRO- Thermocouple Type - 200 °C to 1370 °C 1.37°C Using Multifunction


TECHNICAL- K–Type Calibrator by Direct/
TEMPERATURE Simulation Method
SIMULATION (Source) Relevant Standard /
Guideline Euromet
Guide – CG-11

53 ELECTRO- ThermocoupleB–Type 600 °C to 1800 °C 4.58°C Using Multifunction


TECHNICAL- Calibrator by Direct/
TEMPERATURE Simulation Method
SIMULATION (Source) Relevant Standard /
Guideline Euromet
Guide – CG-11

54 ELECTRO- ThermocoupleE–Type -200 °C to 1000 °C 1.16°C Using Multifunction


TECHNICAL- Calibrator by Direct/
TEMPERATURE Simulation Method
SIMULATION (Source) Relevant Standard /
Guideline Euromet
Guide – CG-11

55 ELECTRO- ThermocoupleJ–Type -200 °C to 1200 °C 1.28°C Using Multifunction


TECHNICAL- Calibrator by Direct/
TEMPERATURE Simulation Method
SIMULATION (Source) Relevant Standard /
Guideline Euromet
Guide – CG-11

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 55 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

56 ELECTRO- ThermocoupleN–Type -200 °C to 1300 °C 1.33°C Using Multifunction


TECHNICAL- Calibrator by Direct/
TEMPERATURE Simulation Method
SIMULATION (Source) Relevant Standard /
Guideline Euromet
Guide – CG-11

57 ELECTRO- ThermocoupleRTD -200 °C to 800 °C 0.84°C Using Multifunction


TECHNICAL- sensor Calibrator by Direct/
TEMPERATURE Simulation Method
SIMULATION (Source) Relevant Standard /
Guideline Euromet
Guide – CG-11

58 ELECTRO- ThermocoupleR–Type 0 °C to 1760 °C 4.6°C Using Multifunction


TECHNICAL- Calibrator by Direct/
TEMPERATURE Simulation Method
SIMULATION (Source) Relevant Standard /
Guideline Euromet
Guide – CG-11

59 ELECTRO- ThermocoupleS–Type 0 °C to 1760 °C 4.55°C Using Multifunction


TECHNICAL- Calibrator by Direct/
TEMPERATURE Simulation Method
SIMULATION (Source) Relevant Standard /
Guideline Euromet
Guide – CG-11

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 56 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

60 ELECTRO- ThermocoupleT–Type -200 °C to 400 °C 0.95°C Using Multifunction


TECHNICAL- Calibrator by Direct/
TEMPERATURE Simulation Method
SIMULATION (Source) Relevant Standard /
Guideline Euromet
Guide – CG-11

61 ELECTRO- Frequency 10 Hz to 100 kHz 0.034% Using Fluke 6 ½ DMM


TECHNICAL- TIME & Model 8846A by Direct
FREQUENCY & Comparison Method
(Measure) Relevant Standard /
Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

62 ELECTRO- Frequency 100 kHz to 1000 kHz 0.034% to 0.012% Using Fluke 6 ½ DMM
TECHNICAL- TIME & Model 8846A by Direct
FREQUENCY & Comparison Method
(Measure) Relevant Standard /
Guideline IS 1248 –
(Part 9), IS 13875 –
(Part 1 & 2)

63 ELECTRO- Timer/Stop WatchHour 1 s to 24 Hr 0.26s to 7.6s Using /Digital Stop


TECHNICAL- TIME & Meter/ Time Interval Watch Measure & Time
FREQUENCY Meter Interval Meter by
(Measure) Comparison Method
Relevant Standard /
Guideline NIST 960-12

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 57 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

64 ELECTRO- Frequency @ 3V 1 kHz to 2 MHz 0.02% to 2.35% Using Fluke 5080 MFC,
TECHNICAL- TIME & Function Generator by
FREQUENCY (Source) Direct Method Relevant
Standard / Guideline IS
1248 – (Part 9), IS
13875 – (Part 1 & 2)

65 ELECTRO- Frequency @ 3V 2 Hz to 45 Hz 1.74% to 0.02% Using Fluke 5080 MFC,


TECHNICAL- TIME & Function Generator by
FREQUENCY (Source) Direct Method Relevant
Standard / Guideline IS
1248 – (Part 9), IS
13875 – (Part 1 & 2)

66 ELECTRO- Frequency @ 3V 45 Hz to 1 kHz 0.02% Using Fluke 5080 MFC,


TECHNICAL- TIME & Function Generator by
FREQUENCY (Source) Direct Method Relevant
Standard / Guideline IS
1248 – (Part 9), IS
13875 – (Part 1 & 2)

67 MECHANICAL- Dig Height Gauge lc 0 mm to 300 mm 13.0µm Using Caliper Checker/


DIMENSION (BASIC 0.01 mm Surface Plate ,Relevant
MEASURING Standard / Guideline -
INSTRUMENT, IS 2921
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 58 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

68 MECHANICAL- Tape & Scale 0 mm to 1000 mm 58.0µm Using Slip


DIMENSION (BASIC Calibrator LC 0.001 Gauge/Length bar
MEASURING mm
INSTRUMENT,
GAUGE ETC.)

69 MECHANICAL- Vernier Calipers lc 0.02 0 mm to 1500 mm 28.0µm Using Length Bar,


DIMENSION (BASIC mm Relevant Standard /
MEASURING Guideline - IS 3651
INSTRUMENT, (Part-I, II, III)
GAUGE ETC.)

70 MECHANICAL- Vernier Calipers lc 0.02 0 mm to 2000 mm 31.0µm Using Length Bar,


DIMENSION (BASIC mm Relevant Standard /
MEASURING Guideline - IS 3651
INSTRUMENT, (Part-I, II, III)
GAUGE ETC.)

71 MECHANICAL- Vernier Height Gauge 0 mm to 1000 mm 17.0µm Length Bar ,Relevant


DIMENSION (BASIC lc 0.02 mm Standard / Guideline -
MEASURING IS 2921
INSTRUMENT,
GAUGE ETC.)

72 MECHANICAL- Vernier Height Gauge 300 mm to 600 mm 17.0µm Using Caliper Checker/
DIMENSION (BASIC lc 0.02 mm Surface Plate ,Relevant
MEASURING Standard / Guideline -
INSTRUMENT, IS 2921
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 59 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

73 MECHANICAL- Low Pressure Pressure (-) 350 mbar to 350 2.71mbar Using Digital
PRESSURE Gauges, Pressure mbar Manometer with
INDICATING DEVICES Transducer, Pressure uncertainty of 0.16
Transmitters, mbar and procedure
Magnahelic gauges & based on DKD-R 6-1
Manometers. guidelines.

74 MECHANICAL- PRESSURE 0 bar to 700 bar 0.16 bar Using Digital pressure
PRESSURE (HYDRAULIC) Digital & gauge with uncertainty
INDICATING DEVICES Dial Pressure Gauges of 0.126 bar, and the
& Pressure procedure based on
Transmitters. DKD-R 6-1 guidelines.

75 MECHANICAL- PRESSURE 0 bar to 10 bar 0.06 bar Using Digital pressure


PRESSURE (Hydraulic/ gauge with uncertainty
INDICATING DEVICES Pneumatic)Digital & of 0.0025 bar and
Dial Pressure GaugeS procedure based on
& Pressure DKD-R 6-1 guidelines.
Transmitters.

76 MECHANICAL- PRESSURE (Hyraulic 0 bar to 70 bar 0.17 bar Using Digital pressure
PRESSURE /Pneumatic)Digital & gauge with uncertainty
INDICATING DEVICES Dial Pressure Gauges of 0.013 bar and
& Pressure procedure based on
Transmitters. DKD-R 6-1 guidelines.

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 60 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

77 MECHANICAL- PRESSURE 0 bar to 2 bar 0.06 bar Using Digital


PRESSURE (PNEUMATIC)Digital & compound gauge with
INDICATING DEVICES Dial Pressure GaugeS uncertainty of 0.00032
& Pressure bar & procedure based
Transmitter. on DKD-R 6-1
guidelines.

78 MECHANICAL- VACUUMVacuum (-) 1 bar to 0 bar 0.06bar Using Digital


PRESSURE Gauges, Vacuum compound gauge with
INDICATING DEVICES Transmitters & uncertainty of 0.00032
Recorders bar and procedure
based on ISO
3567/ISO 27893
standards.

79 MECHANICAL- Electronic Weighing 1 mg to 80 g 0.03 mg Using Accuracy Class


WEIGHING SCALE Balance ( Class I & E1 Weight, comparison
AND BALANCE coarser)d = 0.01 mg method as per,
Relevant Standard /
Guideline - OIML R-76-
1

80 MECHANICAL- Electronic Weighing 1 mg to 220 g 0.40 mg Using E1 accuracy


WEIGHING SCALE Balance ( Class I & class weight, and
AND BALANCE coarser)d = 0.1 mg procedure based on
OIML R-76-1
guidelines.

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 61 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

81 MECHANICAL- Electronic Weighing 0 kg to 6 kg 0.12 g Using F1 accuracy


WEIGHING SCALE Balance ( Class II & class weight and pro
AND BALANCE coarser)d = 0.01 g edure based on OIML
R-76-1 guidelines.

82 MECHANICAL- Electronic Weighing 0 kg to 300 kg 58.0 g Using M1 accuracy


WEIGHING SCALE Balance ( Class III & class weight and
AND BALANCE coarser)d = 50.0 g procedure based on
OIML R-76-1
guidelines.

83 MECHANICAL- Electronic Weighing 0 g to 500 g 0.91 mg Using E1 accuracy


WEIGHING SCALE Balance (Class I & class weights and
AND BALANCE coarser)d = 0.1 mg procedure based on
OIML R-76-1

84 MECHANICAL- Elecyrojic Weighing 0 kg to 30 kg 3.6 g Using M1 accuracy


WEIGHING SCALE Balance ( Class III & class weight and
AND BALANCE coarser)d = 1.0 g proxedure based on
OIML R-76-1
guidelines.

85 MECHANICAL- Spring Balance 1 kg to 10 kg 1.2 g to 3.1 g Using F1 Class Weight


WEIGHING SCALE
AND BALANCE

86 MECHANICAL- Spring Balance 10 kg to 100 kg 3.1 g to 57.8 g Using M1 Class Weight


WEIGHING SCALE
AND BALANCE

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 62 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

87 THERMAL- SPECIFIC Relative Humidity/ 10 °C to 45 °C 1.65 °C Using Digital


HEAT & HUMIDITY Temperature Temperature / Humidity
Indicators, Analog Hygrometer with
/Digital Hygrometer, traceability by
Digital Temp/Humidity comparison Method
Indicator ,
Temperature/Humidity
chamber,
Environmental
Chambers

88 THERMAL- SPECIFIC Relative Humidity/ 10 % RH to 95 % RH 0.83%RH to 1.83%RH Using Digital


HEAT & HUMIDITY Temperature Temperature / Humidity
Indicators, Indicator ,Hygrometer
Probes,Thermo with traceability of
Hygrometer, calibration
Temperature/Humidity
chamber,
Environmental
chambers at site

89 THERMAL- Environmental -80 °C to 400 °C 0.83°C Using Standard RTD /


TEMPERATURE chambers TC and Data Logger
with traceability by
Comparison Method

90 THERMAL- High temperature 1200 °C to 1600 °C 7.1°C Using Single position


TEMPERATURE Furnace and oven “s” Type Thermocouple
With Indicator

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 63 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

91 THERMAL- Hot Air Oven,Liquid 400 °C to 1200 °C 7.1°C Using Multi position
TEMPERATURE Bath, Muffle Furnace Standard RTD / TC and
Data Logger with
traceability by
Comparison Method

92 THERMAL- Hot/ Cold Temperature -80 °C to 400 °C 0.83°C Using Single position
TEMPERATURE Chamber, Hot Air multi position RTD and
Oven, Furnace, Liquid N type Thermocouple
Bath, Muffle Furnace with indicator as master
with calibration
traceability.

93 THERMAL- Non Contact 50 °C to 500 °C 4.15°C Using Standard Non


TEMPERATURE Pyrometer, IR Contact IR Pyrometer,
Thermometer and Block Body Source by
radiation sources, Comparison Method

94 THERMAL- Oven,Furnace, 200 °C to 1000 °C 4.7°C Using Multi position N


TEMPERATURE type Thermocouple
with datalogger by
comparison Method.
Multi point thermal
mapping

This is annexure to 'Certificate of Accreditation' and does not require any signature.
Laboratory Name P.TEJ CALIBRATION CENTRE, C-27, PAYAL NAGAR SOCIETY, NARODA,
AHMEDABAD, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2319 Page No. : 64 / 64

Validity 11/10/2019 to 10/10/2021 Last Amended on 22/11/2019

S.No Discipline / Group Measurand or Measurement range * Calibration and Calibration or


Reference and additional Measurement Measurement
Material/Type of parameters where Capability(CMC)(±) Method or
instrument or applicable(Range procedure
material to be and Frequency)
calibrated or
measured / Quantity
Measured /
Instrument
Site Facility

95 THERMAL- RTD / Thermo couple/ 50 °C to 250 °C 0.83°C Using Single position


TEMPERATURE Temperature Indicator SSPRT with Oil bath by
with Sensor without comparison Method
sensor / Temperature Relevant Standard /
Gauges, Temperature Guideline Relevant
Transmitter with Standard / Guideline-
Sensor IS: 7358, EURAMET
cg-8, ASTM E220 13

* CMCs represent expanded uncertainties expressed at approximately the 95% level of confidence, using a coverage factor of k = 2.

This is annexure to 'Certificate of Accreditation' and does not require any signature.

You might also like