3 cell 12.

6V 40A 18650 lithium battery protection board (with recovery function - AUTO Recovery)

Model: BMS-40A-3S-E / B / S
Integrated with 10 low internal resistance MOSFETS, continuous discharge 40A, 100mA equalizing current, suitable for electric drills,
sprayers, LED lights, low power inverters (400W).

BMS-40A-3S-S Standard BMS 3 cell 12.6V 40A lithium battery protection board (with recovery function - AUTO Recovery)
Starting motor less than 60A / power less than 100W.
BMS-40A-3S-E Same as above with the difference of Starting motor less than 80A / power less than 135W.

BMS-40A-3S-B Battery balance version, Starting motor less than 80A / power less than 135W.

Application range: Suitable for lithium batteries with a normal voltage of 3.7V and fully charged 4.2V.
including 1860 to 26650, Polymer lithium batteries.
PCB Size: 41 x 60 x 3.4mm
Weight: 9.8g
Charging Voltage: 12.6 ~ 13.6V
Continues discharge max: 40A
If heat dissipation environment is not adequate please reduce load
Continues discharge normal: 40A
Standard version (-S): Applicable to start electric motor with current below 60A and power up to 100W.
Enhanced version (-E): Applicable to start electric motor with current below 80A and power up to 135W, with interference function.

Recommended conditions:

Shenzhen City, Guangdong Science and Technology Co., Ltd. Address: China's Shenzhen Futian District, Shenzhen Huaqiang North Road
Copyright © 2010-2015 1688.com All rights reserved. Copyright and Trademark Notices
 3S40A : Electric parameter Min Nor Max Unit Notes
Self consuming current 12 18 24 uA
Overcharge protection voltage 4.2 4.25 4.3 V
Balance charging start voltage 4.17 4.12 4.23 V Balance Charging Version
Balance current 95 100 105 mA Balance Charging Version
Balance charging Power 1.17 1.29 1.43 W Balance Charging Version
Over-discharge protection voltage A 2.4 2.5 2.6 V
Voltage after over discharge protection 2.8 3 3.2 V 1C Discharge
Voltage after over discharge protection 3.2 3.5 3.8 V 2C Discharge
 Over-discharge recovery voltage 2.9 3.2 3.3 V
Rds （on）  2.5 3 3.5 mΩ
Over-current protection current (-S) 54 60 66 A Standard version
Over-current protection current (-B & -E) 70 80 90 A Balance & Enhanced Version
 Over-current delay time 100 150 200 ms
Continue work current 0 40 40 A
Continue output power 0 504 504 W
Environment temperature -40 25 85 °C

Trouble shooting:
Fault phenomenon Fault Checking and Causes Action
Measure the voltage of 3 batteries. If the voltage of one group of Match the batteries well, and don't mix the
Unable to charge batteries is exceeds about 4.25V, the protection board will start good batteries with the bad ones (normal
overcharge protection. function, no warranty)
Measure the voltage of 3 groups of batteries. If the voltage of one group Match the batteries well, and don't mix the
Unable to discharge of batteries is less than 2.7V, the protection board will start overcharge good batteries with the bad ones (normal
protection. function, no warranty)
Rewire or renew the board
Charge / discharge failure 0V、4.2V、8.4V、12.6V wrong connection
(Human fault, no warranty)
Overcharge/over-discharge Rewire or renew the board
0V、4.2V、8.4V、12.6V wrong connection
failure (Human fault, no warranty)
Check the battery pack whether has sufficient discharge capacity and Replacement of batteries with stronger
Discharge protection the starting current of the load whether exceeds the over-current discharge or protective board with larger
protection current of the protective board. current (beyond working range, no warranty
There is no connection between one pin of the component and PCB by return)
Element virtual welding
welding.
Remove components and re-weld
Element continuous welding There is a short circuit between two or more pins of a component.
(Maintainable by return)
In the absence of electricity, measure the G, D and S pins of MOS Removal and replacement MOSFETs
Electrostatic breakdown A transistors. If the forward and reverse resistances of any two pins are transistors
0Ω, it has been damaged.
Remove the MOSFET's transistors and measure the resistance values Removal and replacement MOSFETs
Electrostatic breakdown B of G and D poles, G and S pins. If there is breakdown, the resistance transistors
should be infinite under normal conditions.
Note 1: The successful start of the drill requires three 15C-20C power battery, or six 10C-15C power battery (ordinary 18650 cannot start the drill!!).
Note 2: Strictly according to map wiring 0V, 4.2V, 8.4V, 12.6V, do not deliberately short circuit.
Note 3: When the load of the brush motor is used, try to connect a non-polar capacitor (withstand voltage above 25V, capacity 10uF-100uF) to the
motor's positive and negative terminals to prevent the reverse spike from the motor. Break the MOSFET's.
Note 4: 3 groups of batteries in series, please ensure that the voltage of each group of batteries, if not the same, please fill each battery separately
and then use in series.

For battery test, discharge and the voltage that drop faster in a particular battery group there are poor batteries in this group.
For some of the poor basis of electronic customers to explain:
Balanced charge is only auxiliary functions, try not to put a good battery and poor battery mixed together! 3 sets of battery capacity / resistance
closer to the better! (2 good battery +1 Poor battery use effect = 3 poor battery use effect).

Shenzhen City, Guangdong Science and Technology Co., Ltd. Address: China's Shenzhen Futian District, Shenzhen Huaqiang North Road
Copyright © 2010-2015 1688.com All rights reserved. Copyright and Trademark Notices