Sony Hdr-sr5 Sr7 Sr8 Level-2 Ver-1.4 Rev-1 SM

HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E
RMT-835
SERVICE MANUAL LEVEL 2

US Model
Ver. 1.4 2008.07 Canadian Model
Revision History AEP Model
UK Model
E Model
About this Australian Model
service manual
Hong Kong Model
Chinese Model
Korea Model
Revised-1 Tourist Model
Replace the previously issued Japanese Model
SERVICE MANUAL 9-852-202-31
with this Manual.
Photo: HDR-SR5
Link
SPECIFICATIONS DISASSEMBLY SCHEMATIC DIAGRAMS
MODEL INFORMATION TABLE BLOCK DIAGRAMS PRINTED WIRING BOARDS
SERVICE NOTE FRAME SCHEMATIC DIAGRAM REPAIR PARTS LIST
• Precaution on Replacing the VC-504 Board

• Precaution on Replacing the CABINET (G) ASSY
The components identified by Les composants identifiés par une
mark 0 or dotted line with marque 0 sont critiques pour la
mark 0 are critical for safety. sécurité.
Replace only with part num- Ne les remplacer que par une pièce
ber specified. portant le numéro spécifié.
DIGITAL VIDEO CAMERA RECORDER
2008G0800-1
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_L2 © 2008.07
9-852-202-32 Sony EMCS Co. Published by Kohda TEC
These specifications are extracted from instruction
manual of HDR-SR5E/SR7E/SR8E.
ENGLISH JAPANESE
SPECIFICATIONS
System Minimum illumination Mass (approx.)
2 lx (lux) ([AUTO SLW SHUTTR] [ON], HDR-SR5E:
Video compression format Shutter speed 1/25 sec) 460 g (1 lb) main unit only
AVCHD (HD)/MPEG2 (SD)/JPEG (Still 0 lx (lux) (during NightShot function) 540 g (1 lb 3 oz) including the NP-FH60
images) rechargeable battery pack
*1 “Exif” is a file format for still images,
Audio compression format HDR-SR7E/SR8E:
Dolby Digital 2/5.1ch established by the JEITA (Japan
Electronics and Information Technology 530 g (1 lb 2 oz) main unit only
Dolby Digital 5.1 Creator 610 g (1 lb 5 oz) including the NP-FH60
Industries Association). Files in this
Video signal rechargeable battery pack
format can have additional information
PAL color, CCIR standards such as your camcorder’s setting Supplied accessories
1080/50i specification AC Adaptor (1)
information at the time of recording.
Hard disk *2 The unique pixel array of Sony’s ClearVid Mains lead (1)
HDR-SR5E: Handycam Station (1)
CMOS sensor and image processing
40 GB Component video cable (1)
system (new Enhanced Imaging A/V connecting cable (1)
HDR-SR7E: Processor) allows for still image resolution USB cable (1)
60 GB equivalent to the sizes described.
Wireless Remote Commander (1)
HDR-SR8E: * The focal length figures are actual figures
3 A button-type lithium battery is already installed.
100 GB resulting from wide angle pixel read-out. Rechargeable battery pack NP-FH60 (1)
When measuring media capacity, 1 GB 21-pin adaptor (1)
equals 1 billion bytes, a portion of which is Input/Output connectors For the models with the mark printed on their
used for data management. Audio/Video output bottom surfaces only.
Recording format 10-pin connector CD-ROM “Handycam Application
Movie (HD): AVCHD 1080/50i Video signal: 1 Vp-p, 75Ω (ohms) Software” (1)
Movie (SD): MPEG2-PS Luminance signal: 1 Vp-p, 75Ω (ohms) – Picture Motion Browser (Software)
Still image: Exif Ver.2.2*1 Chrominance signal: 0.3 Vp-p, 75Ω (ohms) – Picture Motion Browser Guide
Audio signal: 327 mV (at load impedance 47 – Handycam Handbook (PDF)
Viewfinder (HDR-SR7E/SR8E) Operating Guide (1)
Electric viewfinder (color) kΩ (kilohms)), Output impedance with less
than 2.2 kΩ (kilohms)
Image device Handycam Station DCRA-C181
COMPONENT OUT jack
HDR-SR5E: Y: 1 Vp-p, 75Ω (ohms)
5.9 mm (1/3 type) CMOS sensor PB/PR, CB/CR: ± 350 mV, 75Ω (ohms) Input/Output connectors
Recording pixels (still image, 4:3):
Max. 4.0 mega (2 304 × 1 728) pixels*2 HDMI OUT jack Audio/Video output
Gross: Approx. 2 100 000 pixels HDMI Type C mini connector 10-pin connector
Effective (movie, 16:9): Headphone jack (HDR-SR7E/SR8E) Video signal: 1 Vp-p, 75Ω (ohms)
1 430 000 pixels Stereo minijack (Ø 3.5 mm) Luminance signal: 1 Vp-p, 75Ω (ohms)
Effective (movie, 4:3): Chrominance signal: 0.3 Vp-p, 75Ω (ohms)
1 080 000 pixels MIC input jack (HDR-SR7E/SR8E) Audio signal: 327 mV (at load impedance 47
Effective (still image, 16:9): Stereo minijack (Ø 3.5 mm) kΩ (kilohms)), Output impedance less than
1 490 000 pixels REMOTE jack 2.2 kΩ (kilohms)
Effective (still image, 4:3): Stereo mini-minijack (Ø 2.5 mm) COMPONENT OUT jack
1 990 000 pixels Y: 1 Vp-p, 75Ω (ohms)
HDR-SR7E/SR8E: LCD screen PB/PR, CB/CR: ± 350 mV, 75Ω (ohms)
6.3 mm (1/2.9 type) CMOS sensor USB jack
Recording pixels (still image, 4:3): Image
6.7 cm (2.7 type, aspect ratio 16:9) mini-B
Max. 6.1 mega (2 848 × 2 136) pixels*2
Gross: Approx. 3 200 000 pixels Total dot number
Effective (movie, 16:9): 211 200 (960 × 220)
AC Adaptor AC-L200/L200B
2 280 000 pixels Power requirements
Effective (movie, 4:3): General AC 100 V - 240 V, 50/60 Hz
1 710 000 pixels
Effective (still image, 16:9): Power requirements Current consumption
2 280 000 pixels DC 6.8 V/7.2 V (battery pack) 0.35 - 0.18 A
Effective (still image, 4:3): DC 8.4 V (AC Adaptor) Power consumption
3 040 000 pixels Average power consumption 18 W
Lens HDR-SR5E: Output voltage
Carl Zeiss Vario-Sonnar T During camera recording using the LCD with DC 8.4 V*
HDR-SR5E: normal brightness: Operating temperature
10 × (Optical), 20 ×, 80 × (Digital) HD: 4.0 W SD: 3.5 W 0 ˚C to + 40 ˚C (32 ˚F to 104 ˚F)
HDR-SR7E/SR8E: HDR-SR7E/SR8E: Storage temperature
10 × (Optical), 20 × (Digital) During camera recording using the -20 ˚C to + 60 ˚C (-4 ˚F to + 140 ˚F)
viewfinder with normal brightness:
Focal length HD: 4.4 W SD: 3.9 W Dimensions (approx.)
F1.8 ~ 2.9 During camera recording using the LCD with 48 × 29 × 81 mm
Filter diameter: 37 mm (1 1/2 in.)
normal brightness: (1 15/16 × 1 3/16 × 3 1/4 in.) (w/h/d)
HDR-SR5E: HD: 4.6 W SD: 4.1 W excluding the projecting parts
f=5.1 ~ 51 mm (7/32 ~ 2 1/8 in.) Mass (approx.)
When converted to a 35 mm still camera Operating temperature
0 ˚C to + 40 ˚C (32 ˚F to 104 ˚F) 170 g (6.0 oz) excluding the mains lead
For movies*3: 41.3 ~ 485 mm (1 11/16 ~ 19 1/
8 in.) (16:9), 50.5 ~ 594 mm (2 ~ 23 1/2 in.) Storage temperature * See the label on the AC Adaptor for other
(4:3) -20 ˚C to + 60 ˚C (-4 ˚F to + 140 ˚F) specifications.
For still images: 40.4 ~ 404 mm (1 5/8 ~ 16 Dimensions (approx.)
in.) (16:9), 37 ~ 370 mm (1 1/2 ~ 14 5/8 in.) Rechargeable battery pack NP-FH60
(4:3) HDR-SR5E:
75 × 81 × 135 mm Maximum output voltage
HDR-SR7E/SR8E: (3 × 3 1/4 × 5 3/8 in.) (w/h/d)
f=5.4 ~ 54 mm (7/32 ~ 2 1/4 in.) When DC 8.4 V
including the projecting parts
converted to a 35 mm still camera 75 × 81 × 140 mm Output voltage
For movies: 40 ~ 400 mm (1 5/8 ~ 15 3/4 in.) (3 × 3 1/4 × 5 5/8 in.) (w/h/d) DC 7.2 V
(16:9), 49 ~ 490 mm (1 15/16 ~ 19 3/8 in.) including the projecting parts, and the NP-
(4:3) Capacity
FH60 rechargeable battery pack attached 7.2 Wh (1 000 mAh)
For still images: 40 ~ 400 mm (1 5/8 ~ 15 3/4
in.) (16:9), 37 ~ 370 mm (1 1/2 ~ 14 5/8 in.) HDR-SR7E/SR8E: Dimensions (approx.)
(4:3) 75 × 81 × 144 mm 31.8 × 33.3 × 45.0 mm
(3 × 3 1/4 × 5 3/4 in.) (w/h/d) (1 5/16 × 1 5/16 × 1 13/16 in.) (w/h/d)
Color temperature including the projecting parts
[AUTO], [ONE PUSH], 75 × 81 × 149 mm Mass (approx.)
[INDOOR] (3 200 K), (3 × 3 1/4 × 5 7/8 in.) (w/h/d) 80 g (2.9 oz)
[OUTDOOR] (5 800 K) including the projecting parts, and the NP- Operating temperature
FH60 rechargeable battery pack attached 0 ˚C to + 40 ˚C (32 ˚F to 104 ˚F)
Type
Lithium ion
Design and specifications are subject to change
without notice.
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_L2
—2—
These specifications are extracted from instruction
ENGLISH JAPANESE
manual of HDR-SR5/SR5C/SR7/SR8.
SPECIFICATIONS
System Minimum illumination Supplied accessories
2 lx (lux) ([AUTO SLW SHUTTR] [ON], AC Adaptor (1)
Video compression format Shutter speed 1/30 sec) Mains lead (1)
AVCHD (HD)/MPEG2 (SD)/JPEG (Still 0 lx (lux) (during NightShot function) Handycam Station (1)
images) Component video cable (1)
*1 “Exif” is a file format for still images, A/V connecting cable (1)
Audio compression format
established by the JEITA (Japan USB cable (1)
Dolby Digital 2/5.1ch
Dolby Digital 5.1 Creator Electronics and Information Technology Wireless Remote Commander (1)
Industries Association). Files in this A button-type lithium battery is already installed.
Video signal format can have additional information Rechargeable battery pack NP-FH60 (1)
NTSC color, EIA standards such as your camcorder’s setting CD-ROM “Handycam Application
1080/60i specification information at the time of recording. Software” (1)
Hard disk * The unique pixel array of Sony’s ClearVid
2 – Picture Motion Browser (Software)
HDR-SR5: CMOS sensor and image processing – Picture Motion Browser Guide
40 GB system (new Enhanced Imaging – Handycam Handbook (PDF)
HDR-SR5C: Operating Guide (1)
Processor) allows for still image resolution
100 GB equivalent to the sizes described.
HDR-SR7: * The focal length figures are actual figures
3
Handycam Station DCRA-C181
60 GB resulting from wide angle pixel read-out.
HDR-SR8: Input/Output connectors
100 GB Input/Output connectors
When measuring media capacity, 1 GB Audio/Video output
equals 1 billion bytes, a portion of which is Audio/Video output 10-pin connector
used for data management. 10-pin connector Video signal: 1 Vp-p, 75Ω (ohms)
Video signal: 1 Vp-p, 75Ω (ohms) Luminance signal: 1 Vp-p, 75Ω (ohms)
Recording format Chrominance signal: 0.286 Vp-p, 75Ω
Movie (HD): AVCHD 1080/60i Luminance signal: 1 Vp-p, 75Ω (ohms)
Chrominance signal: 0.286 Vp-p, 75Ω (ohms)
Movie (SD): MPEG2-PS Audio signal: 327 mV (at load impedance 47
Still image: Exif Ver.2.2*1 (ohms)
Audio signal: 327 mV (at load impedance 47 kΩ (kilohms)), Output impedance less than
Viewfinder (HDR-SR7/SR8) kΩ (kilohms)), Output impedance with less 2.2 kΩ (kilohms)
Electric viewfinder (color) than 2.2 kΩ (kilohms) COMPONENT OUT jack
Image device COMPONENT OUT jack Y: 1 Vp-p, 75Ω (ohms)
HDR-SR5/SR5C: Y: 1 Vp-p, 75Ω (ohms) PB/PR, CB/CR: ± 350 mV, 75Ω (ohms)
5.9 mm (1/3 type) CMOS sensor PB/PR, CB/CR: ± 350 mV, 75Ω (ohms) USB jack
Recording pixels (still image, 4:3): HDMI OUT jack mini-B
Max. 4.0 mega (2 304 × 1 728) pixels*2 HDMI Type C mini connector
Gross: Approx. 2 100 000 pixels
Headphone jack (HDR-SR7/SR8)
AC Adaptor AC-L200/L200B
Effective (movie, 16:9):
1 430 000 pixels Stereo minijack (Ø 3.5 mm) Power requirements
Effective (movie, 4:3): MIC input jack (HDR-SR7/SR8) AC 100 V - 240 V, 50/60 Hz
1 080 000 pixels Stereo minijack (Ø 3.5 mm) Current consumption
Effective (still image, 16:9): 0.35 - 0.18 A
1 490 000 pixels REMOTE jack
Effective (still image, 4:3): Stereo mini-minijack (Ø 2.5 mm) Power consumption
1 990 000 pixels 18 W
HDR-SR7/SR8: LCD screen Output voltage
6.3 mm (1/2.9 type) CMOS sensor DC 8.4 V*
Image
Recording pixels (still image, 4:3): 6.7 cm (2.7 type, aspect ratio 16:9) Operating temperature
Max. 6.1 mega (2 848 × 2 136) pixels*2 0 ˚C to + 40 ˚C (32 ˚F to 104 ˚F)
Gross: Approx. 3 200 000 pixels Total dot number
Effective (movie, 16:9): 211 200 (960 × 220) Storage temperature
-20 ˚C to + 60 ˚C (-4 ˚F to + 140 ˚F)
2 280 000 pixels
Effective (movie, 4:3): General Dimensions (approx.)
1 710 000 pixels 48 × 29 × 81 mm
Effective (still image, 16:9): Power requirements (1 15/16 × 1 3/16 × 3 1/4 in.) (w/h/d)
2 280 000 pixels DC 6.8 V/7.2 V (battery pack) excluding the projecting parts
Effective (still image, 4:3): DC 8.4 V (AC Adaptor)
Mass (approx.)
3 040 000 pixels Average power consumption 170 g (6.0 oz) excluding the power cord
Lens HDR-SR5/SR5C:
Carl Zeiss Vario-Sonnar T During camera recording using the LCD with * See the label on the AC Adaptor for other
normal brightness: specifications.
HDR-SR5/SR5C:
10 × (Optical), 20 ×, 80 × (Digital) HD: 4.2 W SD: 3.6 W
HDR-SR7/SR8: Rechargeable battery pack NP-FH60
HDR-SR7/SR8:
10 × (Optical), 20 × (Digital) During camera recording using the
viewfinder with normal brightness: Maximum output voltage
Focal length HD: 4.5 W SD: 4.0 W DC 8.4 V
F1.8 ~ 2.9 During camera recording using the LCD with Output voltage
Filter diameter: 37 mm (1 1/2 in.) normal brightness: DC 7.2 V
HDR-SR5/SR5C: HD: 4.7 W SD: 4.2 W Capacity
f=5.1 ~ 51 mm (7/32 ~ 2 1/8 in.) Operating temperature 7.2 Wh (1 000 mAh)
When converted to a 35 mm still camera 0 ˚C to + 40 ˚C (32 ˚F to 104 ˚F)
For movies*3: 41.3 ~ 485 mm (1 11/16 ~ 19 1/ Dimensions (approx.)
8 in.) (16:9), 50.5 ~ 594 mm (2 ~ 23 1/2 in.) Storage temperature 31.8 × 33.3 × 45.0 mm
(4:3) -20 ˚C to + 60 ˚C (-4 ˚F to + 140 ˚F) (1 5/16 × 1 5/16 × 1 13/16 in.) (w/h/d)
For still images: 40.4 ~ 404 mm (1 5/8 ~ 16 Dimensions (approx.) Mass (approx.)
in.) (16:9), 37 ~ 370 mm (1 1/2 ~ 14 5/8 in.) HDR-SR5/SR5C: 80 g (2.9 oz)
(4:3) 75 × 81 × 135 mm Operating temperature
HDR-SR7/SR8: (3 × 3 1/4 × 5 3/8 in.) (w/h/d) 0 ˚C to + 40 ˚C (32 ˚F to 104 ˚F)
f=5.4 ~ 54 mm (7/32 ~ 2 1/4 in.) When including the projecting parts
converted to a 35 mm still camera 75 × 81 × 140 mm Type
For movies: 40 ~ 400 mm (1 5/8 ~ 15 3/4 in.) (3 × 3 1/4 × 5 5/8 in.) (w/h/d) Lithium ion
(16:9), 49 ~ 490 mm (1 15/16 ~ 19 3/8 in.) including the projecting parts, and the NP- Design and specifications are subject to change
(4:3) FH60 rechargeable battery pack attached without notice.
For still images: 40 ~ 400 mm (1 5/8 ~ 15 3/4 HDR-SR7/SR8:
in.) (16:9), 37 ~ 370 mm (1 1/2 ~ 14 5/8 in.) 75 × 81 × 144 mm
(4:3) (3 × 3 1/4 × 5 3/4 in.) (w/h/d)
Color temperature including the projecting parts
[AUTO], [ONE PUSH], 75 × 81 × 149 mm
[INDOOR] (3 200 K), (3 × 3 1/4 × 5 7/8 in.) (w/h/d)
[OUTDOOR] (5 800 K) including the projecting parts, and the NP-
FH60 rechargeable battery pack attached
Mass (approx.)
HDR-SR5/SR5C:
460 g (1 lb) main unit only
540 g (1 lb 3 oz) including the NP-FH60
rechargeable battery pack
HDR-SR7/SR8:
530 g (1 lb 2 oz) main unit only
610 g (1 lb 5 oz) including the NP-FH60
rechargeable battery pack
—3—
ENGLISH JAPANESE
概略仕様
システム入/出力端子ハンディカムステーション
映像圧縮方式 A/V OUT 端子 DCRA-C180
AVCHD（HD）/MPEG2（SD）/JPEG（静止 10ピン特殊コネクター入/出力端子
画）映像：1 Vp-p、75 Ω
Y出力：1 Vp-p、75 Ω A/V OUT端子
音声圧縮方式
C出力：0.286 Vp-p、75 Ω 10ピン特殊コネクター
Dolby Digital2/5.1ch
音声：327 mV （47 kΩ負荷時）、出力インピー映像：1 Vp-p、75 Ω
ドルビーデジタル5.1クリエーター搭載
ダンス2.2 kΩ以下 Y出力：1 Vp-p、75 Ω
映像信号 C出力：0.286 Vp-p、75 Ω
COMPONENT OUT 端子
NTSCカラー、EIA標準方式音声：327 mV（47 kΩ負荷時）、出力インピー
1080/60i方式 D1/D3映像：コンポーネントビデオ端子ダンス2.2 kΩ以下
Y：1 Vp-p、75 Ω
ハードディスク PB/PR、CB/CR：±350 mV、75 Ω COMPONENT OUT端子
HDR-SR7 HDMI OUT 端子 D1/D3映像：コンポーネントビデオ端子
60 GB Y：1 Vp-p、75 Ω
HDMIタイプCミニ端子 PB/PR、CB/CR：±350 mV、75 Ω
HDR-S R8
ヘッドホン端子
100 GB USB 端子
ステレオミニジャック（ø 3.5 mm） mini-B
容量は、 1GBを10億バイトで計算した場合
の数値です。また管理用ファイルなどを含む MIC入力端子
ため、実際使用できる容量は若干減少する場ステレオミニジャック（ø 3.5 mm） ACアダプター AC-L200/L200B
合があります。 RE MOTE 端子電源
動画記録方式ステレオミニミニジャック（ø 2.5 mm） AC 100 V∼240 V、50/60 Hz
動画HD：AVCHD 1080/60i
消費電力
動画SD：MPEG2-PS
液晶画面 18 W
静止画記録方式
画面サイズ定格出力
Exif Ver.2.2*
6.7 cm（2.7型、アスペクト比16：9） DC 8.4 V *
ファインダー
総ドット数動作温度
電子ファインダー：カラー
211 200ドット 0 ℃∼+40 ℃
撮像素子横960×縦220 保存温度
6.3 mm（1/2.9型）CMOSセンサー
−20 ℃∼+60 ℃
記録画素数：静止画時最大610万画素相当**
電源部、その他外形寸法
（2 848×2 136）（4：3時）
総画素数：約320万画素電源電圧約 48×29×81 mm（最大突起部をのぞく）
動画時有効画素数（16：9モード）：約228万画バッテリー端子入力 6.8 V/7.2 V （幅×高さ×奥行き）
素 DC端子入力 8.4 V 質量
動画時有効画素数（4：3モード）：約171万画消費電力約170 g
（本体のみ）
素
ファインダー使用時、明るさ標準：
静止画時有効画素数（16：9モード）：約228万 * その他の仕様については AC アダプターのラ
HD：4.5 W SD：4.0 W
画素ベルをご覧ください。
液晶画面使用時、明るさ標準：
静止画時有効画素数（4：3モード）：約304万
HD：4.7 W SD：4.2 W
画素
動作温度リチャージャブルバッテリーパック
ズームレンズ
0 ℃∼+40 ℃ NP-FH60
カールツァイスバリオゾナーT
保存温度最大電圧
10倍（光学）、20倍（デジタル）
フィルター径37 mm −20 ℃∼+60 ℃ DC 8.4 V
F1.8∼2.9 外形寸法公称電圧
f=5.4∼54 mm 75×81×144 mm DC 7.2 V
35mmカメラ換算では動画撮影時（突起部を含む）容量
40∼400 mm（16：9モード）（幅×高さ×奥行き）
（4：3モードでは49∼490 mm）
7.2 Wh（1 000 mAh）
75×81×149 mm
静止画撮影時：最大外形寸法
（突起部を含む、付属バッテリーNP-FH60装
40∼400 ｍｍ（16：9モード）着状態）約31.8×33.3×45.0 mm
（4：3モードでは37∼370 mm）（幅×高さ×奥行き）（幅×高さ×奥行き）
色温度切り換え本体質量質量
［オート］、［ワンプッシュ］、（3 200
［屋内］約530 g
（本体のみ）約80 g
K）、（5 800 K）
［屋外］
撮影時総質量使用温度
最低被写体照度約610 g
（バッテリーNP-FH60含む。） 0 ℃∼+40 ℃
5 lx（ルクス）
（［オートスロシャッタ］［入］、使用電池
［シャッタースピード］1/30秒） Li-ion
0 lx（ルクス）
（NightShot時）付属品
• ACアダプター（1）本機の仕様および外観は、改良のため予告なく変
*（社）電子情報技術産業協会（JEITA）にて
• 電源コード（1）更することがありますが、ご了承ください。
制定された、撮影情報などの付帯情報を追
• ハンディカムステーション（1）
加することができる静止画用のファイル
フォーマット。 • D端子コンポーネントビデオケーブル（1）
**ソニー独自のクリアビッドCMOSセン • AV 接続ケーブル（1）
サーの画素配列と画像処理システム新エ • USBケーブル（1）
ンハンスドイメージングプロセッサーに • ワイヤレスリモコン（1）
より、静止画は表記の記録サイズを実現し • リチャージャブルバッテリーパック
NP-FH6 0（1）
ています。
• CD-ROM「Handycam Application
Software」
（1）
–「Picture Motion Browser」
（ソフトウェア）
–「Picture Motion Browser ガイド」
–「ハンディカムハンドブック」（PDF）
• 取扱説明書（1）
• 保証書（1）
—4—
Ver. 1.1 2007.06
Model information table

Model SR5 SR5C SR5E SR7
AEP, UK, CH,
Destination US, CND, KR, E, JE US US, CND, KR, E, JE, J
HK, AUS, E, JE
Color system NTSC NTSC PAL NTSC
HDD 40G 100G 40G 60G
Viewfinder
HP jack/MIC jack
CM board CM-076 CM-076 CM-076 CM-077
BL board BL-013
Model SR7E SR8 SR8E

AEP, UK, CH, AEP, UK, CH,
Destination US, CND, KR, E, JE, J
HK, AUS, E, JE HK, AUS, E, JE
Color system PAL NTSC PAL
HDD 60G 100G 100G
Viewfinder
HP jack/MIC jack
CM board CM-077 CM-077 CM-077
BL board BL-013 BL-013 BL-013
• Abbreviation
AR : Argentine model
AUS : Australian model
BR : Brazilian model
CH : Chinese model
CND : Canadian model
EE : East European model
HK : Hong Kong model
J : Japanese model
JE : Tourist model
KR : Korea model
MX : Mexican model
NE : North European model
—5—
ENGLISH JAPANESE
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
PUBLISHED BY SONY. DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following

safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered Unleaded solder
connections. Check the entire board surface for solder splashes Boards requiring use of unleaded solder are printed with the lead-
and bridges. free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
2. Check the interboard wiring to ensure that no wires are
the lead free mark due to their particular size.)
"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly
: LEAD FREE MARK
transistors, that were installed during a previous repair. Point
Unleaded solder has the following characteristics.
them out to the customer and recommend their replacement. • Unleaded solder melts at a temperature about 40°C higher than
4. Look for parts which, through functioning, show obvious signs ordinary solder.
of deterioration. Point them out to the customer and Ordinary soldering irons can be used but the iron tip has to be
recommend their replacement. applied to the solder joint for a slightly longer time.
5. Check the B+ voltage to see it is at the values specified. Soldering irons using a temperature regulator should be set to
6. Flexible Circuit Board Repairing about 350°C.
• Keep the temperature of the soldering iron around 270˚C Caution: The printed pattern (copper foil) may peel away if the
during repairing. heated tip is applied for too long, so be careful!
• Strong viscosity
• Do not touch the soldering iron on the same conductor of the
Unleaded solder is more viscous (sticky, less prone to flow) than
circuit board (within 3 times). ordinary solder so use caution not to let solder bridges occur such
• Be careful not to apply force on the conductor when soldering as on IC pins, etc.
or unsoldering. • Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
—6—
ENGLISH JAPANESE
注意
電池の交換は，正しく行わないと破裂する恐れがあり
ます。電池を交換する場合には必ず同じ型名の電池
又は同等品と交換してください。
サービス，点検時には次のことにご注意下さい。
1. 注意事項をお守りください。 6. フレキシブルプリント基板の取扱いについて
サービスのとき特に注意を要する個所については， • コテ先温度を270℃前後にして行なって下さい。
キャビネット，シャーシ，部品などにラベルや捺印で • 同一パターンに何度もコテ先を当てないで下さい。
注意事項を表示しています。これらの注意書き及び取（３回以内）
扱説明書等の注意事項を必ずお守り下さい。 • パターンに力が加わらないよう注意して下さい。
2. 指定部品のご使用を 7. 無鉛半田について
セットの部品は難燃性や耐電圧など安全上の特性を無鉛半田を使用している基板には，無鉛（Lead Free）を
持ったものとなっています。従って交換部品は，使用意味するレッドフリーマークがプリントされています。
されていたものと同じ特性の部品を使用して下さい。（注意：基板サイズによっては，無鉛半田を使用して
特に回路図，部品表に0印で指定されている安全上重要いてもレッドフリーマークがプリントされて
な部品は必ず指定のものをご使用下さい。いないものがあります）
3. 部品の取付けや配線の引きまわしはもとどおりに：レッドフリーマーク
安全上，チューブやテープなどの絶縁材料を使用した無鉛半田には，以下の特性があります。
り，プリント基板から浮かして取付けた部品がありま • 融点が従来の半田よりも約40℃高い。
す。また内部配線は引きまわしやクランパによって発従来の半田こてをそのまま使用することは可能です
熱部品や高圧部品に接近しないよう配慮されていますが，少し長めにこてを当てる必要があります。
ので，これらは必ずもとどおりにして下さい。温度調節機能のついた半田こてを使用する場合，約
4. サービス後は安全点検を 350℃に設定して下さい。
サービスのために取外したネジ，部品，配線がもとど注意：半田こてを長く当てすぎると，基板のパター
おりになっているか，またサービスした個所の周辺をン（銅箔）がはがれてしまうことがあります
劣化させてしまったところがないかなどを点検し，安ので，注意して下さい。
全性が確保されていることを確認して下さい。 • 粘性が強い
5. チップ部品交換時の注意従来の半田よりも粘性が強いため，IC端子などが半田
• 取外した部品は再使用しないで下さい。ブリッジしないように注意して下さい。
• タンタルコンデンサのマイナス側は熱に弱いため交 • 従来の半田と混ぜて使用可能
換時は注意して下さい。無鉛半田には無鉛半田を追加するのが最適ですが，
従来の半田を追加しても構いません。
—7—
1. SERVICE NOTE ENGLISH JAPANESE
1-1. POWER SUPPLY DURING REPAIRS

In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off so
that the unit cannot operate.
These following method is available to prevent this.
Method:
Use the AC power adaptor (AC-L200/L200B).
1-2. SELF-DIAGNOSIS FUNCTION

1-2-1. Self-diagnosis Function 1-2-2. Self-diagnosis Display
When problems occur while the unit is operating, the self-diagnosis When problems occur while the unit is operating, the counter of the
function starts working, and displays on the Viewfinder or the LCD Viewfinder or the LCD screen shows a 4-digit display consisting of
screen what to do. This function consists of two display; self- an alphabet and numbers, which blinks at 3.2 Hz. This 5-character
diagnosis display and service mode display. display indicates the “repaired by:”, “block” in which the problem
Details of the self-diagnosis functions are provided in the Instruction occurred, and “detailed code” of the problem.
manual.
Viewfinder or LCD screen

C:31:11
Blinks at 3.2Hz
C 31 11
Repaired by: Block Detailed Code

C : Corrected by customer Indicates the appropriate Refer to “1-2-3. Self-diagnosis Code Table”.
H : Corrected by dealer step to be taken.
E : Corrected by service E.g.
engineer 31 ....Reload the tape.
32 ....Turn on power again.
1-1
ENGLISH JAPANESE
1-2-3. Self-diagnosis Code Table

Self-diagnosis Code
Repaired by:
Block Detailed Symptom/State Correction

Function Code
C 0 4 0 0 Non-standard battery is used. Use the InfoLITHIUM battery.

“Memory Stick Duo” is unformatted. Format the “Memory Stick Duo”.
C 1 3 0 1
“Memory Stick Duo” is broken. Insert a new “Memory Stick Duo”.
Remove the power source. Reconnect it again and operate your
C 1 3 0 2 Disc access error
camcorder again
Retry turn the power on by the power switch. If it does not
recover, check the focus MR sensor of lens block (pin ql, wa of
Difficult to adjust focus CN5302 on the LD-228 board: SR5/SR5C/SR5E, pin qh, qk of
C 3 2 6 0
(Cannot initialize focus) CN5301 on the LD-228 board: SR7/SR7E/SR8/SR8E). If it is
OK, check the focus motor drive IC (IC5404 on the LD-228
board).
E 2 0 0 0 EEPROM data are rewritten. Make EEPROM data correct value.
E 3 1 0 0 Drive fault Inspect or replacement of the hard disk drive.

Inspect the lens block zoom MR sensor (pin qh, qk of CN5302
on the LD-228 board: SR5/SR5C/SR5E, pin w;, wa of CN5301
on the LD-228 board: SR7/SR7E/SR8/SR8E) when zooming is
Zoom operations fault
E 6 1 1 0 performed when the zoom lever is operated, and the zoom motor
(Cannot initialize zoom lens.)
drive circuit (IC5404 on the LD-228 board) when zooming is not
performed.
The abnormalities in initialization of

the focus lens and the abnormalities in
E 6 1 1 1 Check both C: 32: 60 and E: 61: 10 of the self-diagnosis code.
initialization of the zoom lens occurred
simultaneously.
Handshake correction function does not Inspect PITCH angular velocity sensors (SE8202 on the CM-076
E 6 2 0 0 work well. (With PITCH angular board: SR5/SR5C/SR5E, SE7202 on the CM-077 board: SR7/
velocity sensor output stopped.) SR7E/SR8/SR8E) peripheral circuits.
Handshake correction function does not Inspect YAW angular velocity sensors (SE8201 on the CM-076
E 6 2 0 1 work well. (With YAW angular velocity board: SR5/SR5C/SR5E, SE7201 on the CM-077 board: SR7/
sensor output stopped.) SR7E/SR8/SR8E) peripheral circuits.
Refer to [1-3-1. E : 62 : 02 (Abnormality of IC for Steadyshot)
E 6 2 0 2 Abnormality of IC for steadyshot.
Occurred] (SR7/SR7E/SR8/SR8E only).
IC for steadyshot and micro controller Inspect the steadyshot circuit (IC5703 on the LD-228 board)
E 6 2 0 3
communication abnormality among. (SR7/SR7E/SR8/SR8E only).
SR7/SR7E/SR8/SR8E only:
1. Inspect the EEPROM (IC1804 on the VC-504 board).
E 6 2 1 0 Shift lens initializing failure.
2. Perform the STEADY HALL adjustment. (Note 1)
3. Replace the lens block. (Note 2)
Refer to [1-3-2. E : 62 : 11 (Shift Lens Overheating (Pitch))
E 6 2 1 1 Shift lens overheating (Pitch).
Refer to [1-3-3. E : 62 : 12 (Shift Lens Overheating (Yaw))
E 6 2 1 2 Shift lens overheating (Yaw).
Refer to [1-3-4. E : 62 : 20 (Abnormality of Thermistor)
E 6 2 2 0 Abnormality of thermistor.
E 9 1 0 1 Abnormality when flash is being charged. Checking of flash unit or replacement of flash unit.
Fault of writing to or erasing the Inspect the flash memory (IC2201 on the VC-504 board).
E 9 4 0 0
flashmemory
Note 1: Perform adjustment by referring to “STEADY HALL Adjustment” in Service Manual, ADJ. After the adjustment, be sure
to perform “GYRO Sensor Sensitivity Adjustment”.
Note 2: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
1-2
ENGLISH JAPANESE
1-3. METHOD OF COPING WITH SHIFT LENS ERROR (SR7/SR7E/SR8/SR8E)
about 330 msec

Note: The length of low section will vary a little depending on the
conditions.
Fig. 2
Change in output voltage of R5792 on the LD-228 board
LD-228 BOARD (SIDE A) VC-504 BOARD (SIDE A)
IC1803
R1846
R5721
IC1803
R1846
IC5703
R5792
R5737
Fig. 1
Measurement points on the LD-228 board and the VC-504 board
1-3-1. E : 62 : 02 [Abnormality of IC for Steadyshot] Occurred (SR7/SR7E/SR8/SR8E)

Order Procedure
1 Turn the power OFF.
While measuring with an oscilloscope the output voltage of R5792 in the periphery of IC5703 on the LD-228 board, turn the
2
power ON to check that the output voltage immediately after the power on change as shown in Fig. 2.
If the output voltage change as shown in Fig. 2, replace the lens block (Note). If it does not change as shown in Fig. 2, inspect
3
the camera control circuit (IC1803 of VC-504 board) periphery.
Note: When the lens block was replaced, execute a necessary adjustment items referring to Service Manual, ADJ.
handheld operation.
1-3
ENGLISH JAPANESE
1-3-2. E : 62 : 11 [Shift Lens Overheating (Pitch)] Occurred (SR7/SR7E/SR8/SR8E)

Connect by the SeusEX and perform the following process.
Order Block Page Address Data Procedure

1 11 80 6BB2 01 Write the data.
2 11 80 7D46 F0 Write the data.
3 11 80 7D48 01 Write the data. (Note 1)
4 11 80 7D48 00 Write the data.
Check if the shift lens moves while setting the order 2 to 7. If the shift lens does not move,
9
replace the lens block (Note 2). When the shift lens moved, proceed to the order 10.
While setting the order 2 to 7, measure with an oscilloscope the output voltage of R5721 in the
10
periphery of IC5703 on the LD-228 board to check the output voltage varies.
If the output voltage does not vary, replace the lens block (Note 2). When the output voltage
11
varied, proceed to the order 12.
While measuring with an oscilloscope the output voltage of R5792 in the periphery of IC5703
13 on the LD-228 board, turn the power ON to check that the output voltage immediately after the
power on change as shown in Fig. 2.
If the output voltage change as shown in Fig. 2, replace the lens block (Note 2). If it does not
14 change as shown in Fig. 2, inspect the camera control circuit (IC1803 of VC-504 board) pe
riphery.
Note 1: Finish this operation within 10 seconds. If it is likely to take more than 10 seconds, set block: 11, page: 80, address:
7D48, data: 00, and then retry.
handheld operation.
1-4
ENGLISH JAPANESE
1-3-3. E : 62 : 12 [Shift Lens Overheating (Yaw)] Occurred (SR7/SR7E/SR8/SR8E)

Connect by the SeusEX and perform the following process.
Order Block Page Address Data Procedure

2 11 80 7D47 F0 Write the data.
Check if the shift lens moves while setting the order 2 to 7. If the shift lens does not move,
9
replace the lens block (Note 2). When the shift lens moved, proceed to the order 10.
While setting the order 2 to 7, measure with an oscilloscope the output voltage of R5737 in the
10
periphery of IC5703 on the LD-228 board to check the output voltage varies.
If the output voltage does not vary, replace the lens block (Note 2). When the output voltage
11
varied, proceed to the order 12.
While measuring with an oscilloscope the output voltage of R5792 in the periphery of IC5703
13 on the LD-228 board, turn the power ON to check that the output voltage immediately after the
power on change as shown in Fig. 2.
If the output voltage change as shown in Fig. 2, replace the lens block (Note 2). If it does not
14 change as shown in Fig. 2, inspect the camera control circuit (IC1803 of VC-504 board)
periphery.
Note 1: Finish this operation within 10 seconds. If it is likely to take more than 10 seconds, set block: 11, page: 80, address:
7D49, data: 00, and then retry.
handheld operation.
1-3-4. E : 62 : 20 [Abnormality of Thermistor] Occurred (SR7/SR7E/SR8/SR8E)

Order Procedure
1 Turn the power ON.
Check that R1846 in the periphery of IC1803 on the VC-504 board is 0 Ω and energizes. If it is not energizes, replace the R1846.
2
When R1846 is 0 Ω and energizes, replace the lens block (Note).
Check that no error occurs, after replacing the lens block and performing the necessary adjustment. If an error occurs, inspect
3
the camera control circuit (IC1803 of VC-504 board) periphery.
Note: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
handheld operation.
1-5
ENGLISH JAPANESE
1-4. PRECAUTION ON REPLACING THE VC-504 BOARD

DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Refer to Service Manual ADJ, and perform “DESTINATION DATA WRITE”.
USB SERIAL No.

The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Refer to Service Manual ADJ, and perform “USB SERIAL No. INPUT”.
1-5. PROCESS AFTER FIXING FLASH ERROR

When “FLASH error” (Self-diagnosis Code E : 91 : 01) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash
is changed automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated. Flash error code can be initialized by execution of “Clear All record-data”.
Note: For “Clear All record-data”, refer to Service Manual, ADJ (“7. Record Data” of “2-2. SERVICE MODE”).
1-6
1. SERVICE NOTE ENGLISH JAPANESE
1-1. 修理時の電源供給について
本機では，安定化電源（8.4Vdc）からバッテリ端子に電源を供給した場合，約10秒後にシャットオフし，動作しなくなります。
これを避けるため，下記の方法を用いてください。
方法：
DC入力端子を使用する。（ACアダプタ（AC-L200/L200Bなど）を使用する。）
1-2. 自己診断機能
1-2-1.自己診断機能について 1-2-2.自己診断表示
本機の動作に不具合が生じたとき，自己診断機能が働き，本機の動作に不具合が生じたとき，ビューファインダまたは
ビューファインダまたはL C D 画面に，どう処置したらよい LCD画面のカウンタ表示部分がアルファベットと数字の4桁
か判断できる表示を行います。「自己診断表示」と「サービス表示になり，3.2Hzで点滅します。この5文字の表示によっ
モード表示」の２つの表示があります。自己診断機能について対応者分類および不具合の生じたブロックの分類，不具合
ては取扱説明書にも掲載されています。の詳細コードを示します。
ビューファインダまたはLCD画面
C:31:11
3.2Hz点滅
C 31 11
対応者分類ブロック分類詳細コード

C ：お客さま自身で対応対応方法の違いにより分類「1-2-3. 自己診断コード表」
H ：販売店で対応例 31･･･テープを入れ直すを参照
E ：サービスエンジニア 32･･･電源を入れ直す
で対応
1-7
ENGLISH JAPANESE
1-2-3. 自己診断コード表
自己診断コード
対ブロック詳細症状／状態対応／方法

応
者機能コード
C 0 4 0 0 標準以外のバッテリを使用しているインフォリチウムバッテリを使用する。
C 1 3 0 1 フォーマットしていない“メモリー “メモリーステックデュオ”をフォーマットする。
ステックデュオ”を入れた
“メモリーステックデュオ”が壊新しい“メモリーステックデュオ”に交換する。
れている
C 1 3 0 2 ディスクアクセスエラー電源を外し，再度入れ直してから操作する。
C 3 2 6 0 フォーカスが合いにくい操作スイッチの電源を入れ直す。
（フォーカスの初期化ができない）復帰しない場合，レンズブロックのフォーカスMRセンサ
（LD-228基板CN5302 ql，waピン：SR5/SR5C/SR5E，LD-
228基板CN5301 qh，qkピン：SR7/SR7E/SR8/SR8E）を点検
する。異常なければフォーカスモータ駆動回路（LD-228基
板IC5404）を点検する。
E 2 0 0 0 EEPROMが書き換えられている EEPROMのデータを元の値に戻す
E 3 1 0 0 ドライブ不良ハードディスクドライブを点検または交換する。
E 6 1 1 0 ズーム動作の異常（ズームレンズのズームレバーを操作したときにズーム動作をすれば，レン
初期化ができない）ズブロックのズームMRセンサ（LD-228基板CN5302 qh，
qkピン：SR5/SR5C/SR5E，LD-228基板CN5301 w;，waピ
ン：SR7/SR7E/SR8/SR8E）を点検する。ズーム動作をしな
ければズームモータ駆動回路（LD-228基板IC5404）を点
検する。
E 6 1 1 1 フォーカス，ズーム異常自己診断コードC：32：60とE：61：10の両方を点検す
る。
E 6 2 0 0 手振れ補正が効きにくい（PITCH PITCH角速度センサ（CM-076基板SE8202：SR5/SR5C/
角速度センサ出力張り付き） SR5E，CM-077基板SE7202：SR7/SR7E/SR8/SR8E）周辺回
路を点検する。
E 6 2 0 1 手振れ補正が効きにくい（YAW 角 YAW角速度センサ（CM-076基板SE8201：SR5/SR5C/
速度センサ出力張り付き） SR5E，CM-077基板SE7201：SR7/SR7E/SR8/SR8E）周辺回
路を点検する。
「1-3-1. E：62：02
（手振れ補正用ICの異常）
が出た場合」
を参照。
E 6 2 0 2 手振れ補正用ICの異常
（SR7/SR7E/SR8/SR8Eのみ）
手振れ補正用ICとマイクロコント手振れ補正回路（LD-228基板IC5703）
を点検。
E 6 2 0 3
ローラーとの通信異常（SR7/SR7E/SR8/SR8Eのみ）
SR7/SR7E/SR8/SR8Eのみ：
E 6 2 1 0 シフトレンズ初期化異常
1. EEPROM（VC-504基板IC1804）
を点検する。
2. STEADY HALL調整を行う。（注意1）
3. レンズブロックを交換する。（注意2）
シフトレンズオーバーヒート「1-3-2. E：62：11
（シフトレンズオーバーヒート（PITCH）
）が出
E 6 2 1 1
(PITCH) た場合」を参照。（SR7/SR7E/SR8/SR8Eのみ）
注意1：ADJ編
「STEADY HALL Adjustment」
を参照して調整を実施すること。調整後は「GYRO Sensor Sensitivity Adjustment」
を必ず実施すること。
注意2：レンズブロックを交換した場合は，ADJ編を参照して必要な調整項目を実施すること。調整後は手振れ補正ONの状
態にして，手持ち動作で手振れ補正が適切に動作していることを確認する。
1-8
ENGLISH JAPANESE
自己診断コード
対ブロック詳細症状／状態対応／方法

応
者機能コード
シフトレンズオーバーヒート「1-3-3. E：62：12（シフトレンズオーバーヒート（YAW））が出

E 6 2 1 2
(YAW) た場合」を参照。（SR7/SR7E/SR8/SR8Eのみ）
「1-3-4. E：62：20（サーミスタの異常）が出た場合」を参照。
E 6 2 2 0 サーミスタの異常
（SR7/SR7E/SR8/SR8Eのみ）
E 9 1 0 1 フラッシュの充電異常フラッシュユニットの点検または交換をする。
E 9 4 0 0 フラッシュメモリの書込み/消去動フラッシュメモリ（VC-504基板IC2201）を点検する。
作不良
1-3. シフトレンズエラーの対処方法（SR7/SR7E/SR8/SR8E）
図2
約 330 msec
注意：Lowの区間の長さは場合によって多少異なる
図2. LD-228基板R5792の出力電圧の変化
図1
LD-228 BOARD (SIDE A) VC-504 BOARD (SIDE A)
IC1803
R1846
R5721
IC1803
R1846
IC5703
R5792
R5737
図1.LD-228基板，VC-504基板測定箇所
1-9
ENGLISH JAPANESE
1-3-1. E：62：02（手振れ補正用ICの異常）
が出た場合 (SR7/SR7E/SR8/SR8E)
順序作業内容
1 電源を切る。
LD-228基板IC5703の周辺にあるR5792の出力電圧をオシロスコープで測定しながら電源を入れる。電源投入直後の
2
出力電圧が図2の様に変化することを確認する。
出力電圧が図2の様に変化するときはレンズブロックを交換する（注意）。図2の様に変化しないときはカメラコン
3
トロール回路（VC-504基板IC1803）周辺を点検する。
注意：レンズブロックを交換した場合は，A D J 編を参照して必要な調整項目を実施すること。調整後は手振れ補正O N の状

1-3-2. E：62：11（シフトレンズオーバーヒート
（PITCH）
）が出た場合 (SR7/SR7E/SR8/SR8E)
SeusEXで接続し、次の手順を行う。
順序ブロックページアドレスデータ作業内容

1 11 80 6BB2 01 データを書き込む。
2 11 80 7D46 F0 データを書き込む。
3 11 80 7D48 01 データを書き込む。（注意1）
4 11 80 7D48 00 データを書き込む。
5 11 80 7D46 10 データを書き込む。
6 11 80 7D48 01 データを書き込む。（注意1）
7 11 80 7D48 00 データを書き込む。
順序2〜7を設定している間にシフトレンズが動いたか確認する。もしシフト
9 レンズが動かない場合はレンズブロックを交換する（注意2）。動く場合は順序
10に進む。
LD-228基板IC5703の周辺にあるR5721の出力電圧をオシロスコープで測定しな
10
がら，順序2∼7を設定したときに出力電圧が変化することを確認する。
出力電圧が変化しないときはレンズブロックを交換する（注意2）
。変化するときは
11
順序12に進む。
13 がら電源を入れる。電源投入直後の出力電圧が図2の様に変化することを確認
する。
出力電圧が図2の様に変化するときはレンズブロックを交換する（注意2）。図2の
14 様に変化しないときはカメラコントロール回路（VC-504基板IC1803）周辺を点検
する。
注意1：この操作は10秒以内に終了してください。もし10秒以上経過しそうな場合は，ブロック：11，ページ：80，アドレ
ス：7D48，データ：00 に設定しなおしてから再度実行してください。
1-10
ENGLISH JAPANESE
1-3-3. E：62：12
（シフトレンズオーバーヒート（YAW））が出た場合 (SR7/SR7E/SR8/SR8E)
SeusEXで接続し、次の手順を行う。
順序ブロックページアドレスデータ作業内容

2 11 80 7D47 F0 データを書き込む。
3 11 80 7D49 01 データを書き込む。（注意1）
4 11 80 7D49 00 データを書き込む。
5 11 80 7D47 10 データを書き込む。
6 11 80 7D49 01 データを書き込む。（注意1）
7 11 80 7D49 00 データを書き込む。
順序2〜7を設定している間にシフトレンズが動いたか確認する。もしシフトレ
9 ンズが動かない場合はレンズブロックを交換する（注意2）。動く場合は順序10
に進む。
10
がら，順序2∼7を設定したときに出力電圧が変化することを確認する。
出力電圧が変化しないときはレンズブロックを交換する（注意2）
。変化するときは
11
順序12に進む。
13 がら電源を入れる。電源投入直後の出力電圧が図2の様に変化することを確認す
る。
出力電圧が図2の様に変化するときはレンズブロックを交換する（注意2）。図2の
様に変化しないときはカメラコントロール回路（VC-504基板IC1803）周辺を点検
する。
注意1：この操作は10秒以内に終了してください。もし10秒以上経過しそうな場合は，ブロック：11，ページ：80，アドレ
ス：7D49，データ：00 に設定しなおしてから再度実行してください。
1-3-4. E：62：20
（サーミスタの異常）が出た場合 (SR7/SR7E/SR8/SR8E)
順序作業内容
1 電源を入れる。
VC-504基板IC1803の周辺にあるR1846が0 Ωであり，かつ通電していることを確認する。通電していない場合は
2
R1846を交換する。R1846が0 Ωであり，かつ通電している場合はレンズブロックを交換する（注意）
。
レンズブロックを交換し必要な調整を行った後，エラーが発生しないことを確認する。もしエラーが発生する場
3
合はカメラコントロール回路（VC-504基板IC1803）周辺を点検する。
注意：レンズブロックを交換した場合は，A D J 編を参照して必要な調整項目を実施すること。調整後は手振れ補正O N の状

1-11
ENGLISH JAPANESE
1-4. VC-504基板交換時の注意
仕向けデータ
補修用基板と交換する時，補修用基板に書かれている仕向けデータは元の設定と違っている場合があります。
ADJ編を参照して，「DESTINATION DATA WRITE」を行ってください。
USBシリアルNo.
セットは，1台毎に異なる固有のID（USB Serial No.）を書き込んだ後，出荷されています。
新品の補修用基板には，このIDが書き込まれていないので，基板交換後にIDを入力する必要があります。
ADJ編を参照して，「USB SERIAL No. INPUT」を行ってください。
1-5. フラッシュ異常修理後の処置
本機はフラッシュエラー（自己診断コードE:91:01 ）が発生した場合，高電圧による異常を防止するために自動的にフラッ
シュ充電および発光禁止の設定になります。
フラッシュエラー発生後はエラーの解除を行う必要があります。エラーは，「全履歴データの初期化」を実行することによ
り解除できます。
注：「全履歴データの初期化」については，ADJ編（「2-2. サービスモード」の「7. 履歴データ」）を参照してください。
1-12
(ENGLISH) HDR-SR5
*Factory *Manufacturing year
(US Model)
1-6. PRECAUTION ON REPLACING
THE CABINET (G) ASSY
(HDR-SR5)
Serial No.
The model display adopts the laser printing method.Therefore, the *Affix the label
Part No. Description
cabinet (G) assy for replacement differs depending on the
A-1317-525-A SERVICE,CABINET (G (SR5)) (U2)
destination.
As similar displays are provided, choose the suitable one for order.
HDR-SR5
Note1: After replacing the cabinet (G) assy, the serial number for it (Canadian Model)
will be changed to the one exclusive for service use.
Inform a customer of the serial number change and change the serial
number in the repair data.
Note 2: When replacing the cabinet (G) assy for US, affix the Serial No.
“Manufacturing year” label and the “Factory” label on the specified Part No. Description
location as shown in the figure. A-1317-526-A SERVICE, (G (SR5)) (CA2)
The replacement caution label and inset (how to affix) are supplied
together with the cabinet (G) assy.
HDR-SR5
Note 3: When replacing the cabinet (G) assy for Korea, affix the (E, Tourist Models)
“Manufacturing year” label on the specified location as shown in
the figure.
together with the cabinet (G) assy. Serial No.
A-1317-527-A SERVICE, (G (SR5)) (E23)
(JAPANESE)
1-6. キャビネット(G)組立交換時の注意 HDR-SR5
(Korean Model)
(HDR-SR5)
機種の表示部はレーザー印字方式を採用しております。
この為，交換用のキャビネット(G)組立は仕向けにより異な
Serial No. *Manufacturing year
ります。類似の表示もありますので，該当するものを選ん *Affix the label
で注文して下さい。 A-1317-528-A SERVICE, (G (SR5)) (KR2)
注意1:　キャビネット(G)組立交換後はシリアルナンバーが
サービス専用のシリアルナンバーに変更されます。お客様
への案内と修理データのシリアルナンバー変更を行ってく
ださい。
注意2 : 　U S 仕向けキャビネット( G ) 組立を交換した際は

「製造年月」を表すラベルと，「製造所」を表すラベルを
図の指定位置に貼り付けてください。
なお，キャビネット(G)組立には時期表示ラベル，投げ込み
(ラベル貼り方)がセットで供給されます。
注意3:　Korean仕向けキャビネット(G)組立を交換した際
は，「製造年月」を表すラベルを図の指定位置に貼り付け
てください。
1-13
(ENGLISH) HDR-SR5C
*Factory *Manufacturing year
(US Model)
(HDR-SR5C)
Serial No.
The model display adopts the laser printing method.Therefore, the *Affix the label
A-1317-533-A SERVICE, (G (SR5C)) (U2)
destination.
Note1: After replacing the cabinet (G) assy, the serial number for it
Note 2: When replacing the cabinet (G) assy for US, affix the
“Manufacturing year” label and the “Factory” label on the specified
location as shown in the figure.
(JAPANESE)
1-7. キャビネット(G)組立交換時の注意
(HDR-SR5C)
ります。類似の表示もありますので，該当するものを選ん
で注文して下さい。
ださい。
注意2 : 　U S 仕向けキャビネット( G ) 組立を交換した際は

1-14
(ENGLISH) HDR-SR5E
(E, Hong Kong, Australian, Tourist Models)
(HDR-SR5E)
Serial No.
The model display adopts the laser printing method.Therefore, the Part No. Description
cabinet (G) assy for replacement differs depending on the A-1317-529-A SERVICE, (G (SR5E)) (E34)
destination.
HDR-SR5E
Note1: After replacing the cabinet (G) assy, the serial number for it (UK Model)
Serial No.
A-1317-530-A SERVICE, (G (SR5E)) (CEH)
(JAPANESE)
(HDR-SR5E) HDR-SR5E
(Chinese Model)
Serial No.
で注文して下さい。 Part No. Description
A-1317-531-A SERVICE, (G (SR5E)) (CN2)
HDR-SR5E
への案内と修理データのシリアルナンバー変更を行ってく (AEP Model)
ださい。
Serial No.
A-1317-532-A SERVICE, (G (SR5E)) (CEN)
1-15
(ENGLISH) HDR-SR7
*Manufacturing year
(Japanese Model)
(HDR-SR7)
Serial No. *Affix the label
The model display adopts the laser printing method.Therefore, the
A-1317-516-A SERVICE, CABINET (G (SR7)) (J)
destination.
HDR-SR7
Note1: After replacing the cabinet (G) assy, the serial number for it *Factory *Manufacturing year
(US Model)
Note 2: When replacing the cabinet (G) assy for US, affix the Serial No. *Affix the label
location as shown in the figure. A-1317-517-A SERVICE, CABINET (G (SR7)) (U2)
HDR-SR7
Note 3: When replacing the cabinet (G) assy for Korea, affix the (Canadian Model)
the figure.
A-1317-518-A SERVICE, (G (SR7)) (CA2)
(JAPANESE)
(E, Tourist Models)
(HDR-SR7)
この為，交換用のキャビネット(G)組立は仕向けにより異な Serial No.
ります。類似の表示もありますので，該当するものを選ん Part No. Description
A-1317-519-A SERVICE, (G (SR7)) (E23)
で注文して下さい。
注意1:　キャビネット(G)組立交換後はシリアルナンバーが HDR-SR7
サービス専用のシリアルナンバーに変更されます。お客様 (Korean Model)
ださい。
注意2 : 　U S 仕向けキャビネット( G ) 組立を交換した際は Serial No. *Manufacturing year

「製造年月」を表すラベルと，「製造所」を表すラベルを *Affix the label
A-1317-520-A SERVICE, (G (SR7)) (KR2)
てください。
1-16
(ENGLISH) HDR-SR7E
(HDR-SR7E)
Serial No.
destination.
HDR-SR7E
Serial No.
A-1317-522-A SERVICE, (G (SR7E)) (CEH)
(JAPANESE)
(HDR-SR7E) HDR-SR7E
(Chinese Model)
ります。類似の表示もありますので，該当するものを選ん Serial No.
HDR-SR7E
ださい。
Serial No.
1-17
(ENGLISH) HDR-SR8 *Manufacturing year
(Japanese Model)
(HDR-SR8)
Serial No.
*Affix the label
The model display adopts the laser printing method.Therefore, the
A-1317-534-A SERVICE, CABINET (G (SR8)) (J)
destination.
HDR-SR8 *Factory *Manufacturing year
Note1: After replacing the cabinet (G) assy, the serial number for it (US Model)
Note 2: When replacing the cabinet (G) assy for US, affix the Serial No.
*Affix the label
location as shown in the figure. A-1317-535-A SERVICE,CABINET (G (SR8)) (U2)
HDR-SR8
Note 3: When replacing the cabinet (G) assy for Korea, affix the (Canadian Model)
the figure.

A-1317-538-A SERVICE, (G (SR8)) (CA2)
(JAPANESE)
(E, Tourist Models)
(HDR-SR8)
この為，交換用のキャビネット(G)組立は仕向けにより異な Serial No.
で注文して下さい。 A-1317-539-A SERVICE, (G (SR8)) (E23)
注意1:　キャビネット(G)組立交換後はシリアルナンバーが HDR-SR8
サービス専用のシリアルナンバーに変更されます。お客様 (Korean Model)
ださい。
注意2 : 　U S 仕向けキャビネット( G ) 組立を交換した際は Serial No. *Manufacturing year

Part No. Description *Affix the label
A-1317-540-A SERVICE, (G (SR8)) (KR2)
てください。
1-18
ENGLISH JAPANESE
(ENGLISH) HDR-SR8E
(HDR-SR8E)
Serial No.
destination.
HDR-SR8E
Serial No.
(JAPANESE) A-1317-542-A SERVICE, (G (SR8E)) (CEH)
(HDR-SR8E) HDR-SR8E
(Chinese Model)
Serial No.
HDR-SR8E
ださい。
Serial No.
1-19E
2. DISASSEMBLY
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Cut and remove the part of gilt
Do not insert the cable insufficiently nor crookedly. which comes off at the point.
(Be careful or some
• When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped. pieces of gilt may be left inside)
• When installing a connector, don’t press down at wire of connector.

It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
DISCHARGING OF THE ST-175 BOARD’S CHARGING CAPACITOR (C5206)
The charging capacitor (C5206) of the ST-175 board is charged

up to the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
Preparing the Short Jig Note: High-voltage cautions

To preparing the short jig, a small clip is attached to each end of
Discharging the Capacitor
a resistor of 1 kΩ /1 W (1-215-869-11). Short-circuit between the two points with the
Wrap insulating tape fully around the leads of the resistor to short jig about 10 seconds.
prevent electrical shock. To avoid the spark with the metal plate,
wrap the short jig with the insulation tape.
1 kΩ/1 W
C5206
(Charging
Wrap insulating tape. Capacitor)
ST-175
Board
R:1 kΩ/1 W
(Part code: 1-215-869-11)
NOTE FOR DISCONNECTION THE HARNESS (COAXIAL CABLE)
When disconnecting the harness (coaxial cable), do not pull the

harness part but pull off the connector body with tweezers etc.
Tweezers etc.
Harness
(coaxial cable)
2-1
2-1. IDENTIFYING PARTS
Control Switch Block SR7/SR7E/
Cabinet (G) Assy
(PS25500) SR8/SR8E
EVF Block
⋅ BL-013 Board
HDD
Cabinet (L) Section BT Panel Block

⋅ VC-504 Board ⋅ MS-374 Board
⋅ JK-342 Board
Bottom Cabinet
Lens Section Lens Section Block
(SR7/SR7E/SR8/SR8E) (SR5/SR5C/SR5E)
⋅ ST-175 Board ⋅ ST-175 Board
⋅ LD-228 Board ⋅ LD-228 Board
⋅ CM-077 Board ⋅ CM-076 Board
- DISASSEMBLY FLOW -
Cabinet (R) Section
⋅ CK-183 Board
2-2-1. OVERALL SECTION-1
- Cabinet (G) Assy
⋅ PD-324 Board
- HDD
- Bottom Cabinet Block
2-2-2. OVERALL SECTION-2 (SR7/SR7E/SR8/SR8E)

2-2-3. OVERALL SECTION-2 (SR5/SR5C/SR5E)
- Cabinet (T(255))
- Cabinet (R) Section
- BT Panel Block
- EVF Block (SR7/SR7E/SR8/SR8E)
2-2-4. OVERALL SECTION-3 2-2-10. CABINET (R) SECTION

- Control Switch Block - Loud Speaker
(PS25500) - CK-183 Board
- Cabinet (F) Block - LCD Panel Block
2-2-11. LCD PANEL BLOCK

2-2-5. CABINET (L) SECTION-1 2-2-7. CABINET (F) BLOCK - Hinge Block
- VC-504 Board - Lens Section - LCD
- Main frame section - Lens Barrier Unit - PD-324 Board
2-2-6. CABINET (L) SECTION-2 2-2-8. LENS SECTION (SR7/SR7E/SR8/SR8E)

- JK-342 Board 2-2-9. LENS SECTION (SR5/SR5C/SR5E)
- ST-175 Board
- LD-228 Board
- Flash Unit (FL25500)
2-2
HELP
2-2. DISASSEMBLY
EXPLODED VIEW HARDWARE LIST
Follow the disassembly in the numerical order given.
1 Cabinet (G) Assy (1-1 to 1-6)
2 HDD (2-1 to 2-3)
3 Bottom Cabinet Block (3-1)
1-2 (#2)
1-1
(Slide the
Jack Cover(G))
1 Cabinet (G)
Assy 2-1
Overall Section-2
(See Page 2-5 (SR5/SR5C/SR5E))
1-6 (See Page 2-4 (SR7/SR7E/SR8/SR8E))
(Claw)
(Note)
1-4 SR5/SR5C/SR5E without
(#2) EVF is same the removing
2 HDD procedure.
2-3
2-2
HELP
1-3
(Open the
Jack Cover
(HDMI))
1-5 (#2)
3-1 (#2)
3 Bottom Cabinet Block
2-3
2-2-2. OVERALL SECTION-2 (SR7/SR7E/SR8/SR8E)
Follow the disassembly in the numerical order given. EXPLODED VIEW HARDWARE LIST
1 Cabinet (T(255)) (1-1 to 1-6)
2 Cabinet (R) Section (2-1 to 2-3)
3 BT Panel Block (3-1)
4 EVF Block (4-1 to 4-2)
1 Cabinet (T(255)) 4 EVF Block

1-1
1-6
1-2 (#2) (Open the Shoe Cover) (Open the EVF)
4-1
(#2)
4-2(#2)
1-3 3-1(#2)
(#2)
2 Cabinet (R)
Section
(See Page 2-12)
3 BT Panel 1-5 (#2)

Block
2-3 (#2)
Note: High-voltage cautions

Short-circuit between the two points with the 1-4
short jig about 10 seconds. (Open the
To avoid the spark with the metal plate,
wrap the short jig with the insulation tape. LCD Panel)
2-1
2-2
(#2)
C5206
(Charging
Capacitor)
ST-175
Board
R:1 kΩ/1 W
(Part code: 1-215-869-11)
2-4
2-2-3. OVERALL SECTION-2 (SR5/SR5C/SR5E)
1 Cabinet (T(255)) Assy (1-1 to 1-5)
2 Cabinet (R) Section (2-1 to 2-3)
3 BT Panel Block (3-1)
1-1
1-2 (#2) (Open the Shoe Cover)
1 Cabinet (T(255)) Assy
3 BT Panel
Block
1-3 3-1(#2)
(#2)
2 Cabinet (R)
Section
(See Page 2-12)
1-5 (#2)
2-3 (#2)
Note: High-voltage cautions

Short-circuit between the two points with the 1-4
short jig about 10 seconds. (Open the
To avoid the spark with the metal plate,
wrap the short jig with the insulation tape.
LCD Panel)
2-1
2-2
(#2)
C5206
(Charging
Capacitor)
ST-175
Board
R:1 kΩ/1 W
(Part code: 1-215-869-11)
2-5
1 Control Switch Block (PS25500) (1-1 to 1-2)
2 Cabinet (F) Block (2-1 to 2-2)
1 Control Switch Block

(PS25500)
1-1 (#12)
1-2 (#2)
SR5/SR5C/SR5E
2-1 (#14)
2 Cabinet (F)
2-2 (#2)
Block
(See Page 2-9)
SR7/SR7E/SR8/SR8E
Cabinet (L)
Section-1
(See Page 2-7)
Refer to page 2-1 "Note

for disconnection the
harness (coaxial cable) "
2 Cabinet (F)
Block
2-2 (#2) (See Page 2-9)
2-6
2-2-5. CABINET (L) SECTION-1
1 VC-504 Board (1-1 to 1-5)
2 Main Frame Section (2-1 to 2-4)
1-4
2-2(#3) 1-3
(Peel off the Flexible Board)
Cabinet (L) Section-2 1-5

(See Page 2-8)
1-2
(#3)
2-1(#14)
(SR7/SR7E/
SR8/SR8E)
2-3
(#12)
4
2-4 50
(#12) VC-
1 VC-504
Board
2 Main Frame Section 1-1 (#3)
2-7
1 JK-342 Board (1-1 to 1-5)
1 JK-342 Board 1-2

1-3 (#2)
1-4
1-5
1-1(#12)
SR7/SR7E/
SR8/SR8E
SR7/SR7E/SR8/SR8E
2-8
2-2-7. CABINET (F) BLOCK
(SR5/SR5C/SR5E)
1 Lens Section (1-1 to 1-2)
2 Lens Barrier Unit (2-1 to 2-2)
(SR7/SR7E/SR8/SR8E)
1 Lens Section (1-1 to 1-2)
2 Lens Barrier Unit (2-1 to 2-5)
SR5/SR5C/SR5E
1 Lens Section
(SR5/SR5C/SR5E)
(See Page 2-11)
HELP
1-1
1-2(#12)
2 Lens Barrier Unit
2-1
2-2 (#8)
1 Lens Section
(SR7/SR7E/SR8/SR8E)
(See Page 2-10)
SR7/SR7E/SR8/SR8E
2 Lens Barrier Unit

HELP
2-1 1-2
2-4 (#12)
(#8)
2-5
1-1(#14)
2-2(#8)
2-3
2-9
2-2-8. LENS SECTION (SR7/SR7E/SR8/SR8E)
1 ST-175 Board (1-1 to 1-3)
2 LD-228 Board (2-1 to 2-4)
3 Flash Unit (FL25500) (3-1 to 3-8)
1 ST-175 Board
1-1(#3)
5
3-6 1-2 (Claw) ST
-17
(Peel off the Flexible Board)

3-7(#23)
3 Flash Unit
(FL25500) 1-3
3-2
3-5(Claw)
(Claw)
3-1 3-8
(#14) 3-3
3-4(#14)
CM
-07
7
2-2
2-1(Claw)
8
2
-2
D
L
2-3(#3)
2-4
2 LD-228 Board for disconnection the Lens Block
2-10
2-2-9. LENS SECTION (SR5/SR5C/SR5E)
1 ST-175 Board (1-1 to 1-3)
2 LD-228 Board (2-1 to 2-4)
3 Flash Unit (FL25500) (3-1 to 3-6)
1 ST-175 Board
3-4
(Peel off the Flexible Board) 1-1(#3)
5
-17
3-5 1-2 (Claw) ST
(#23) 3-3
3 Flash Unit (Claw)
(FL25500)
3-1
3-6 1-3
3-2(#14)
CM
-07
6
2-2
2-1
(Claw)
8
2
-2
D
L
2-3
(#3)
2-4 2 LD-228 Board

for disconnection the
Lens Block
2-11
2-2-10. CABINET (R) SECTION
1 Loud Speaker (1-1 to 1-2)
2 CK-183 Board (2-1 to 2-4)
3 LCD Panel Block (3-1 to 3-4)
3 LCD Panel Block

(See Page 2-13)
1 Loud Speaker
1-2
1-1 (#8)
CK
-18 3-4
3
3-3
2-1 (#12)
(#8)
3-1
(#12)
2-3
2-2
(#12) 3-2
2-4 2 CK-183
Board
2-12
1 Hinge Block (1-1 to 1-9)
2 LCD (2-1 to 2-2)
3 PD-324 Board (3-1 to 3-2)
HELP
1 Hinge Block
HELP
1-8
1-4 1-5
(#12) 1-9 (#2)
1-6 3-2
(Claw)
1-7
2-1
(#8)
3 PD-324 Board PD
-32
4
1-1
(#2) A
3-1
B E
C
D
1-3 D
1-2 B
(Claw) C
2-2
2 LCD
2-13E
HELP
Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
SR5/SR5C/SR5E SR7/SR7E/SR8/SR8E
Don't put the FPC on the Flexible Board of

projection in this point. the Lens Barrier Unit
The FPC edge should be in the
pocket of Lens Frame (L(253)).
Set the tape edge to Lens Flexible Sheet

the scratched line. (10mm × 15mm)
Lens Flexible Sheet

(10mm × 15mm)
Set the FPC edge to
the scratched line.
THE METHOD OF ATTACHMENT OF FP-718 FLEXIBLE BOARD

1
3 Be sure to tighten this

FP-718 Flexible screw in the end.
Board
HELP
THE METHOD OF ATTACHMENT OF FP-537 FLEXIBLE BOARD AND FP-546 FLEXIBLE
BOARD
1 Fold dotted line parts of the FP-537 flexible board 3 Install the flexible clamp in the hinge assy.
as shown in figure.
Fold
Flexible clamp Hinge assy
Adhesive tape
Adhesive
tape Fold Adhesive tape
4 Roll the the FP-537 flexible board 1.5 times,
in the direction of arrow A.
5 Put the adhesive sheet and FP-537 flexible

board on the hinge assy according to the
2 Pass the FP-537 flexible board through position of the boss.
the flexible clamp.
Flexible clamp
Boss
Adhesive tape
HELP
6 Fold dotted line parts of the FP-546 flexible board as shown in figure.
Switch
Valley fold
FP-546 flexible board
7 Install the FP-546 flexible board in the panel hinge cover (C) as shown in figure.
8 Install the panel hinge cover (C) in the hinge assy as shown in figure.

Plate of hinge
Hijnge assy
Switch
Panel hinge cover (C)
HELP
3. BLOCK DIAGRAMS
Link
OVERALL BLOCK DIAGRAM (1/7) OVERALL BLOCK DIAGRAM (6/7)
OVERALL BLOCK DIAGRAM (2/7) OVERALL BLOCK DIAGRAM (7/7)
OVERALL BLOCK DIAGRAM (3/7) POWER BLOCK DIAGRAM (1/3)
Ver. 1.1 2007.06 3. BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/7) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
CM-077 BOARD (SR7/SR7E/SR8/SR8E) VC-504 BOARD (1/6)

CN6601
CN1201
1 - 5 18 - 25, 29 - 32, 37 - 40
LENS BLOCK 4M_DCOUT1-4M_DCOUT6, 4M_DCOUT1-4M_DCOUT6,
4M_DRVOUT1-4M_DRVOUT6, 4M_DRVOUT1-4M_DRVOUT6,
1 - 12, 16 - 23
A9, A10, B9, B10, E9, E10,

F9, F10, J9, J10, K9, K10
AC17, AA16, AB16,

E7, D7, F7 D1, E2, E1, F2, F1, A4, B4, C4, D4, E4, J3, K3, F4, G4, H4,
AC16, AA15, AB15,

AC15, AA14, AB14,
B2, B1, C2, C1, D2 B5, A5, C5, D5, E5 F3, G3, J2, H3, K2
IRIS 6M_DCOUT1-6M_DCOUT8, 6M_DCOUT3, 4, 7, 8,
AC14, Y13, AA13

J4, K4, F5, G5
27 - 34,
39 - 46
AB13, AB12
(SHUTTER) DCOUT1 - DCOUT8, DRVOUT1 - DRVOUT8 6M_DRVOUT1-6M_DRVOUT8 6M_DRVOUT3, 4, 7, 8
AD0_0 - AD0_13
IC6701
AHS_TGHD, AHS_TGVD, AHS_XCSO, SR5/SR5C/SR5E
J22, G23, H21, AB21, AC21, AA20, U22, U23, V21, V22,
AB19, AC19, AA18 W23, Y21, Y22, Y23,

AB18, AC18, Y17, AA21, AA22, AA23
CMOS IMAGER
K23, M22, AA6 AB20, AC20, AA19, V23, W21, W22,

AHS_SCK, AHS_SO
A3, B3, C3, D3

CHCK2/4M
4-8
14
CHCK3/6M AD2_0 - AD2_13
2 16 CHCK3/6M CHCK
XSYS_RST 25
10 11
SR7/SR7E/SR8/SR8E IC1201
TRIPLE CHANNEL
E6, F6, G6 G2, G1, H2, H1
AA17, AB17
ADC_1
SE7202 (2/21)
YAW_AD XSYS_RST XSYS_RST AD1_0 - AD1_13
PITCH SENSOR 6 16 8 30
5 IC7201
SE7201
VST_C_RESET
YAW SENSOR 10 PITCH/YAW 17 9
SENSOR
11 AMP VST_C_RESET ADC_SCK, ADC_SO, XCS_ADC0, ADC_TGVD, ADC_TGHD, CAM_VD_HS
32
PITCH_AD YAW_AD OVERALL (6/7)
20 7 33
PITCH_AD
1 (PAGE 3-6)
34 XSYS_RST XSYS_RST
D6 T4
CLPOB CLPOB IC1702
SR7/SR7E/SR8/SR8E H5 K21
CHCK CHCK (1/3)
AHS_TGHD, AHS_TGVD, K5 U1
36 - 40
OVERALL (6/7) B4 CAMERA
AHS_XCS0, AHS_SCK, AHS_SO
2 (PAGE 3-6) SIGNAL
PROCESS
(4/21)
CM-076 BOARD (SR5/SR5C/SR5E)
LENS BLOCK
CN6801
IRIS
15 - 19 37 - 42
19 - 30
7 - 12,
(SHUTTER) DCOUT1 - DCOUT6, DRVOUT1 - DRVOUT6
J9, J10, K9, K10,

A9, A10, B9, B10
A4, B4, C4, D4, E4, E7, D7, F7 J3, K3, F4, G4, H4,
F3, G3, J2, H3, K2
6M_DCOUT1, 2, 5, 6,
J4, K4, F5, G5

AHS_TGHD, AHS_TGVD, AHS_XCSO, 6M_DRVOUT1, 2, 5, 6
IC6901 AHS_SCK, AHS_SO 1-5 AD1_0 - AD1_13
CMOS IMAGER
CHCK2/4M
23 17
E6, F6, G6
XSYS_RST
27 11 IC1301
TRIPLE CHANNEL
ADC_2
N21 - N23, P21 - P23,

R21 - R23, T21 - T23,
B5, A5, C5, D5, E5
(3/21)
A3, B3, C3, D3

SE8202
YAW_AD
U20, U21
PITCH SENSOR 6 16 8
AD3_0 - AD3_13
5 IC8201
SE8201
VST_C_RESET
YAW SENSOR 10 PITCH/YAW 17 9
SENSOR
11 AMP XSYS_RST
D6
PITCH_AD CLPOB
20 7 H5
CHCK
K5
SR5/SR5C/SR5E
SR7/SR7E/SR8/SR8E
IC1701
CHCK
1 FF 5
(4/21)
X1701
80.919081MHz : SR5/SR5C
62.37MHz : SR5E
89.010989MHz : SR7/SR8 : VIDEO SIGNAL
74.25MHz : SR7E/SR8E
08
3-1
VC-504 BOARD (2/6)

: VIDEO SIGNAL
V11, W10, W12, Y9, AE20, AH20, AH19, AF18, AE17, AH16,
Y11, T10, V9, V10, AE18, AJ20, AF19, AH18, AD17, AH15
J5, N13,
M4, F13
B19, D19, D18,
A19, C18, C19,
H1, G1 - G4,
D17, C17
EMC_XDQM[0-3]
F1 - F3
VIN_C0 - VIN_C7
AH24, AG21, AG26, AH22,
R5, R4, T3, R3, E2, R12, P12, P13, N11, M10,
AJ24, AG20, AH25, AD19,
AA9, U12, V12, U11, AD18, AJ21, AH26, AG19,
D4, F4, E4, E3, D3, M11, L10, L11, H11, H10,
AJ23, AF26, AH21, AG25,
AJ22, AJ25, AH23, AJ26,
P6, E5, K5, L4, L5 G11, G10, F11, E13, E12,

D13, P2, P3, N2, N3, P4,
T11, W11, Y10, Y8 AE19, AJ19, AF20, AG18
P5, N5, N4, J4, H5, H4,

G5, G4, F5, G2, G3
D16, C16, A15, B15,
B16, B17, C15, D15
E2, E1, D1 - D3,
C1 - C3
EMC_DATA [0] - EMC_DATA [31]
VIN_Y0 - VIN_Y7
VIN_HD, VIN_VD, VIN_FLD,
A17, A20,
C20, D20,
H2 - H4,
J4, R1
EXT_CAM_CLK, STL_BUS_CTRL EMC_ADDR [0] - EMC_ADDR [12], IC2201
A9
EMC_ADDR [0] - EMC_ADDR [15] EMC_ADDR [14], EMC_ADDR [15] (1/2)
512M SDRAM
(8/21)
SYS_V
D25 EMC_CKE
SSS AJ15 F3
C28 EMC_XCAS
XWEN AE16 J11
D29 EMC_XCS [1]
XHI_SCK AF10 J13
OVERALL (6/7) J17 EMC_CLK0_OUT
(PAGE 3-6) 3 XCS_IC1803
G17
W25 K11
HI_SI IC2101 W26
H17 EMC_XWE
HI_SO (1/4) AF17 J10
K17 EMC_XRAS
EXT_CAM_VD CPU AG16 J12
B20
(7/21, 9/21, 10/21)
V5, T6, P8, P9, R9, R10,

P10, T9, R11, T12, U12
A8, C6, C7, J11, H10, J10, H14, D14, B14, A14, C14, D12, A13,
H15, J16, G15 K10, H12, H11, G13, D13, C12, A12, B13, C13, D11,
T11, U11, U6, R7, R8,

B12, B11, C11, A11
EMC_DATA [0] - EMC_DATA [15]

STL_DATA/CCD_IN0-13, IC2201
STL_DATA14, 15 (2/2)
512M OneNAND FLASH
(8/21)
C10, B10, D10, F8,

C11, B11, D11, E9
F6, C4, D5, C5,
E6, D6, C6, E7,
G12, G11, H13, G10
EMC_ADDR [0] - EMC_ADDR [15]

STL_ADDR0-11
IC1702
(2/3) EMC_XWE
P7
STL_CLK, STL_CKE, STL_XCAS, EMC_XRAS
CAMERA STL_XWE, STL_XCS0, STL_XRAS T5
SIGNAL EMC_XOE
AG15 N10
PROCESS EMC_RDY0
AG17 R6
(4/21) EMC_XRESET_OUT
STL_BS0 AF16 P11
J15 EMC_XCS [0]
STL_BS1 AG10 U3
G14 EMC_CLK1_OUT
Y25 T4
XFLASH_RST
Y26 E8
OVERALL (4/7)
XFLASH_RST 4 (PAGE 3-4)
R8, N7, R9, N8, P9, M8, M7, L8,
L2, M3, M2, P1, N2, R1, N3, R2,
E8, D7, D8, B9, C8, A9, C7, A8,
A2, C3, A1, C2, B1, D2, D3, E2
B18, A18, B19, A19, C20, B20,
A16, D17, C17, B17, A17, C18,
A20, B21, A21, B22, C4, B4,
C7, B7, C8, B8, A8, C9, B9

C5, A5, D6, C6, B6, A6, D7,
A2, A8, B1, B2, B8, B9,

C1, C2, C8, C9, D1,
D2, D8, D9, E1, E9
STL_DATA/CCD_IN0-13,
STL_DATA/CCD_IN0-13, STL_DATA/CCD_IN0-13,
STL_DATA14-31
STL_DATA14-31 STL_DATA14, 15
C12, B12, A12, D13,
C13, B13, A13, A14,
D15, C15, B15, A15
G1, G2, G3, H1,
H9, H8, H7, H3,

H2, H1, G3, G2
G8, G9, F7, F3,
H2, J3, G7, H9
J8, J7, J3, J2,

STL_ADDR0-11 STL_ADDR0-11 STL_ADDR0-11
IC1901 IC1902
256M 32BIT 128M 16BIT
SDRAM SDRAM
(6/21) (6/21)
B10, C10, A3
A9, D9, A10,
STL_CLK, STL_CKE, STL_XCAS, STL_CLK, STL_CKE, STL_XCAS, STL_CLK, STL_CKE, STL_XCAS,

G9, F9, F8,
J1, J2, K7,
J9, K8, J8
F7, F3, F2
STL_XWE, STL_XCS0, STL_XRAS STL_XWE, STL_XCS0, STL_XRAS STL_XWE, STL_XCS0, STL_XRAS
STL_BS0 STL_BS0 STL_BS0

A11 J7 G7
STL_BS1 STL_BS1 STL_BS1
D12 H8 G8
SD_DQM SD_DQM SD_DQM
B11 F2 E8
F8 F1
K1
K9
SR7/SR7E/SR8/SR8E SR5/SR5C/SR5E
08
3-2
VC-504 BOARD (3/6) FP-728 BL-013

Q2908 FLEXIBLE BOARD BOARD
IC2901_C/PB_OUT
E32, G33, D35, E34, D33, D34,
B16, A16, B17, A17, D18, B18,

(SR7/SR7E/SR8/SR8E) (SR7/SR7E/SR8/SR8E)
E33, F33 D32, C34, B33, C33

AA11
A15, A14 A18, B19, A20, B21

BUFFER
Q2910 CN3701 CN5901 CN5902
DR_VDATA0 - DR_VDATA7 IC2901_Y_OUT OVERALL (4/7)
AA9 BUFFER 7 (PAGE 3-4) IC3702 H2
EVF_HST
3 18 5
Q2911 EVF_HCK2
IC2901_PR_OUT EVF DRIVER G1 4 17 6
Y10 BUFFER EVF_HCK1
DR_GHDATA0 - DR_GHDATA3 (17/21) F1 5 16 7
EVF_R EVF_REF
DR_GHPILOT Y7 D11 G11 7 14 11
H35 B15 EVF_G EVF_VST
Y6 E11 K3 8 13 13
G32, G34,
D14, B14,
D13, A13
F32, F34
IC2901 EVF_B EVF_EN LCD902
DR_GSDATA0 - DR_GSDATA3 AA7 F11 K1 9 12 15
(1/2) EVF_STB COLOR
EVF_HD J2 10 11 12 EVF
DR_GSPILOT SOC K4 A2 EVF_VCK
G35 D12 (12/21) EVF_VD L3 11 10 14 UNIT
DR_VINCK J2 B1 EVF_PCG
F35 E21 H1 12 9 16
XCS_IC2901 EVF_VB
U27 H2 XBB_SCK L8 13 8 17
DR_SCK54 A4 EVF_VR
E35 F20 BB_SO L6 14 7 18
XBB_RST B4 EVF_VG
G20 J21 BB_SI L7 15 6 19
XBB_RST A5 EVF_PSIG
L10 16 5 20
XCS_EVF EVF_COM
R27 K11 17 4 21
EVF_BL_ON XBB_RST
IC2101 D26 C1 Q3701
XCS_EVF LED_K D5901
(2/4) B5 G10 EVF BL SWITCH 20 1 (EVF BACK LIGHT)
CPU
(7/21, 9/21, 10/21) EVF_BL_ON
SR7/SR7E/SR8/SR8E
CN1006
OVERALL (4/7) SP
1, 2
BB_SI Q2904 (PAGE 3-4) 9
6 AA2 BUFFER
PANEL_R
26
OVERALL (5/7) Q2903
PANEL_G
(PAGE 3-5) AA4 BUFFER 27
Q2902
XBB_SCK PANEL_B
M18 H1 AA5 BUFFER 28
BB_SO
K1, K2
20, 24
M19 G2 PANEL_VD, PANEL_HD
BB_SI
L18 J1
XBB_SCK
14 FP-727 FLEXIBLE
BB_SO TO CK-183 BOARD
XBB_SCK 16 OVERALL (7/7)
OVERALL (4/7) (PAGE 3-4) BB_SI
BB_SO 8 OVERALL (5/7) (PAGE 3-5) 17 (PAGE 3-7)
PANEL_O/C PANEL_O/C
G24 30
PANEL_NOR/REV PANEL_NOR/REV
H25 3
KEY_AD2 KEY_AD2
AJ35 5
KEY_AD0 KEY_AD0
AH35 23
XCS_LCD XCS_LCD
T27 15
TP_SEL1 TP_SEL1
B29 11
TP_X TP_X
AM35 10
TP_Y TP_Y
AN34 12
Q1013 HI_XRESET
6
: VIDEO SIGNAL
TP_SEL2 TP SELECT XBATT_VIEW
B28
SWITCH 4 : AUDIO SIGNAL
: VIDEO/AUDIO SIGNAL
CN1004 FP-515 FLEXIBLE BOARD

AK1, AJ4, AM2 AM9 - AM11 AM12, AN12
AH8 - AH14
AJ8 - AJ14
34 - 49
ATA_D0 - ATA_D15 DD0 - DD15
HARD
12, 13, 17, 18, 21, 26, 27, 31 14 - 16

ATA_A0 - ATA_A2 DA0 - DA2 DISK
DRIVE
AL1, AM1, AM3,
AM4, AN4,
XATA_CS1, XATA_CS0, ATA_INTRQ, XATA_DMACK, ATA_IORDY, XATA_DIOR, XATA_DIOW, ATA_DMARQ CS1, CS0, INTRQ, DMACK, IORDY, DIOR, DIOW, DMARQ
XATA_RESET XATA_RESET RESET

AL4 51
HDD_ACCESS DASP-
11
OVERALL (4/7) BOOT_MODE_PORT0
(PAGE 3-4) 11 D_2.8V_PERI
R1060
CN1001 MEM_SEL1
MD2 AG34
17 MEM_SEL2 FP-720 MS-374 BOARD
XCS_MC_FLASH AF34
15 HI_XRESET FLEXIBLE
EEP_SI R1063 R1061
13
EEP_SO OVERALL (6/7) OVERALL (4/7)
XBATT_VIEW BOARD
12
EEP_SCK
5 (PAGE 3-6) (PAGE 3-4) 10 HDD_ACCESS CN1017 CN7401 CN7402
11 XMS_IN XMS_IN XMS_IN
AP_ENABLE 22 11 6
10
CPC XSYS_RST
14 XMS_ACC_LED XMS_ACC_LED D7401
H23 14 20
(ACCESS)
MEMORY
AM30, AN33,
20, 24, 26, 28

AN30, AM32
5, 7, 9, 13
BOOT_MODE_PORT0
3, 4, 5, 7
7 AA1 STICK
(For check) UART2_SI UART2_SI MSX_BIO0 - MSX_BIO3 MSDATA0 - MSDATA3 DUO
5 H27
UART2_SO UART2_SO
4 G27 MSX_BS MS_BS MSBS
UART3_SI UART3_SI AM31 30 3 2
3 J25 MSX_CLK MSX_CLK MS_SCLK
UART3_SO UART3_SO AR32 18 15 8
2 K26
08
3-3
Ver. 1.1 2007.06
FP-722 FLEXIBLE BOARD VC-504 BOARD (4/6)

C13 FP-718 FLEXIBLE BOARD
(SR7/SR7E/SR8/SR8E) CN1013
CN7181
J7222 CN1022 C14
A13 VIDEO_I/O VIDEO_I/O VIDEO_I/O
MIC EXT_MIC_L L1 34 8
2 B12 S_C_I/O S_C_I/O S_C_I/O
(PLUG IN POWER) EXT_MIC_R IC3301 M2 32 12
4 B11 S_Y_I/O S_Y_I/O S_Y_I/O
VIDEO, AUDIO K1 30 16
J7221 A12 PROCESSOR AUDIO_L_I/O AUDIO_L_I/O AUDIO_L
HP_R_OUT F2 28 20
7 D1 (16/21) AUDIO_R_I/O AUDIO_R_I/O AUDIO_R
HP_L_OUT G1 27 22
(headphone) 9 D2 IC2901_Y_OUT
N4
Q3302 Q3303 IC2901_C/PB_OUT D3_LNO_Y D3_LNO_Y Y
N3 35 47 9
HP MUTE HP MUTE D3_LNO_PB D3_LNO_PB PB
ADA_LRCK IC2901_Y_OUT 33 49 13
9 13
2 D3_LNO_PR D3_LNO_PR PR
B1, C2
B3 SP ADA_SIA0 OVERALL (3/7) IC2901_C/PB_OUT 31 51 17
HP_JACK_IN OVERALL (3/7) ADA_FCK (PAGE 3-3) 7 IC2901_PR_OUT
4
LINE_CNT1 LINE_CNT1 CTRL1 CRADLE
11 OVERALL (5/7) 6 43 2 21 (Handycam Station)
(PAGE 3-3) ADA_BCK LINE_CNT2 LINE_CNT2 CTRL2
(PAGE 3-5) 42 3 23
SR7/SR7E/SR8/SR8E XBB_SCK XBB_SCK LINE_CNT3 LINE_CNT3 CTRL3
J13 22 41 4 25
BB_SO BB_SO USB_D+ USB_D+
CN1020 K13 23 22 34
USB_D- USB_D-
INT_MIC_L IC3001 20 36
4 B14 ADA_LRCK D4 DRIVER XD3_CRADLE_DET DET
M13 N29 XBB_SCK 1 19
MIC901 ADA_SIA0 (13/21) JACK_AD_CRADLE MULTI_JACK_IN
MICROPHONE 6
INT_MIC_R
B13
P12
N14
ADA_FCK
R29 BB_SO 8 KEY_AD3 KEY_AD3
25
PON(DVD-BURN)
26
UNIT M29 8 37
ADA_BCK OVERALL (3/7) (PAGE 3-3) LANC_DC LANC_DC
INT_MIC_F M14 M28 6 33
2 A10 OVERALL (5/7) (PAGE 3-5) LANC_SIG LANC_SIG
MIC_JACK_IN 5 31
L14 D23 XCS_DDRA
SYS_SOUND T25 20
A4 R35 XD_CN_DET XD3_CN
CN1019 XCS_IC3301 A23 44 40
J14 U26 FP-726 JK-342 BOARD
FP-725 FLEXIBLE BOARD SHOE_MIC_FL ADA_SOA0
12 A11 N13 N28
SHOE_MIC_FR ADA_SOA1 USB_D+ FLEXIBLE
13 B10 P13 P29 W35
SHOE_MIC_RL USB_D- BOARD
9 A8 XMIC_MONO V35 CN1026 CN7303 CN7302
SHOE_MIC_RR L13 U24 XD3_CRADLE_DET
10 B7 AN11 VIDEO_I/O VIDEO_I/O
K14 IC2101 KEY_AD3 6 21 9
HOT AH33 S_C_I/O S_C_I/O
EXT_STROBE_ON OVERALL (6/7) (3/4) 4 23 5
SHOE 4 12 (PAGE 3-6) HP_JACK_IN CPU
S_Y_I/O
2 25
S_Y_I/O
10
J26 AUDIO_L_I/O AUDIO_L_I/O
HOTSHOE_ID1 HOTSHOE_ID1 (7/21, 9/21, 10/21) 14 13 1
8 AM34 AUDIO_R_I/O AUDIO_R_I/O AV OUT
HOTSHOE_ID2 HOTSHOE_ID2 12 15 6
5 AM33 JACK_AD JACK_AD JACK_AD
LANC_SIG AJ34 9 18 7
3 LANC_DC LANC_DC
8 19 4
LANC_SIG LANC_SIG
XSYS_RST 10 17 2
IC5101 A8 G2
XCS_EX CN7301
LANC PROCESSOR H3 D22
X5101 FR_SI LINE_CNT_1 CTRL1
(21/21) J4 B22 19 8 6
32.768kHz FR_SO LINE_CNT_2 CTRL2
L2 L5 C22 18 9 7
WD_DIS LINE_CNT_3 CTRL3
D9 G23 17 10 8
XHOT_STBY D3_LNO_Y Y COMPONENT
E10 C23 25 2 1 OUT
XFR_SCK D3_LNO_PB PB
L3 K5 A22 23 4 3
: VIDEO SIGNAL E9
STABLE_RUN
V2
D3_LNO_PR
21 6
PR
5
GSENS_REF XD3_CN SW
: AUDIO SIGNAL L8 AL33
H26
START/STOP 16 11 10
SR5E/SR7/SR7E/SR8/SR8E XPHOTO_LED
AK3
OVERALL (3/7) BOOT_MODE_PORT0 ZOOM_VR_AD
(PAGE 3-3) 11 H9
13 3
GSENS_Z
AK35
AJ33
KEY_AD1 FP-721 FLEXIBLE
GSENS_TEMP SE3801 GSENS_Y AH34
K7 1 4 AF35 BOARD
G SENSOR GSENS_X
5 AG35 CN1009 J7211
LANC_DC
20
SR5/SR5C XLANC_JACK_IN REMOTE
19
LANC_SIG
18
10
SE3802
5 9
G SENSOR
8
CONTROL SWITCH BLOCK (PS25500)
JACK_AD_CRADLE
J11 CN1003 S001
XLANC_JACK_IN
C5 KEY_AD3 N.S_SW (NIGHT SHOT)
19
S006
START/STOP S/S START/
3 STOP
XPHOTO_LED XPHOTO_LED D003

13 (PHOTO)
LANC_IN LANC_DC
B10 J3 IC4701 L2
LANC_OUT LANC_SIG
C10 J2 POWER SUPPLY K3 RV001
HI_XRESET VTR_DD_ON ZOOM_VR_AD ZOOM_VR_AD
K2 P3 (20/21) N5 10 W T
IC5104 N7 (ZOOM)
AND S002
(21/21) XSTROBE_SW XSTROBE_SW
1 2 ( /CHG)
B8 4 XFLASH_RST OVERALL (2/7)
F2
VTR_DD_ON 3 4 (PAGE 3-2)
S003
PHOTO_FREEZE PHOTO_FREEZE
6 (PHOTO FREEZE)
PHOTO
HI_XRESET S004
KEY_AD1 PHOTO_REC PHOTO_REC
XBATT_VIEW 7 (PHOTO REC)
D_2.8V B2 OVERALL (3/7)
*1 B6
XMS_IN 10 (PAGE 3-3)
R1076 HDD_ACCESS
GENERAL_AD OFF (CHG)
K11
XPOWER_SW XPOWER_SW XPOWER_SW
*1 B4 5 ON POWER
XMODE_SW XMODE_SW XMODE_SW
R1077 A2 4
XCHARGE_LED
G11 MODE
XCAM_LED
F11
D002
XCHARGE_LED XCHARGE_LED
17 (CHARGE/STROBE)
*1 SR5/SR5C SR5E SR7/SR8 SR7E/SR8E D004

XCAM_LED XCAM_LED
R1076 XX 0 100K 22K 15 (CAM)
R1077 0 XX 22K 100K
D001
HDD_ACCESS X_ACCESS_LED
12 (ACCESS)
08
3-4
Ver. 1.1 2007.06
VC-504 BOARD (5/6) FP-719 FLEXIBLE BOARD
CN1021 CN7191
A9, A10, B9 - B12, A2 - A4, B2 - B4,

W20, W21, Y20, AA14, Y13, AA13, AA18,Y17, AA17,
TMDS_DATA2+_1 TMDS DATA2+ TMDS_DATA2_+
U21, V20, V21, Y15, AA15, Y14, Y19, AA19, Y18,
G9 - G11, K12,L1 - L11,
J7, J8, K1- K4, K7

A2 22 2
F1 - F3, H4 - H7,
G1 - G3, J2 - J4,
Y16, AA16
F10, F12, J9, J1, K1, K2,
J10, K10, J12 M3 - M11

C1, D1
TMDS_DATA2-_1 TMDS DATA2- TMDS_DATA2_-
E1 - E3, H2,
HM_R0 - HM_R7 A3 21 3
AD98_D0 - AD98_D23 TMDS_DATA1+_1 TMDS DATA1+ TMDS_DATA1_+
A4 18 5
TMDS_DATA1-_1 TMDS DATA1- TMDS_DATA1_-
A5 17 6
AD98_SCK, AD98_IDCK, AD98_SD0, AD98_SD1, TMDS_DATA0+_1 TMDS DATA0+ TMDS_DATA0_+
A6 14 8
Y12, AA12
C12, D12
AD98_MCLK, AD98_DE, AD98_HSYNC, AD98_WS TMDS_DATA0-_1 TMDS DATA0- TMDS_DATA0_-
H3, K8, K9,

J9, G8, G9,
E8, F8, F9
HM_Y0 - HM_Y7 A7 13 9
AD98 - VSYNC TMDS_CLOCK+_1 TMDS CLOCK+ TMDS_CLOCK_+
A8 10 11
TMDS_CLOCK-_1 TMDS CLOCK- TMDS_CLOCK_- HDMI
A9 9 12
Q3201
Y21, AA20
A5 - A8,
B5 - B8
SDA_CN SDA SDA
HM_B0 - HM_B7 C9 5 16
LEVEL SHIFT SCL_CN SCL SCL
XHDMI_RST B10 6 15
F4 B2
HM_FLD
R21 C4
HM_VD XCS_IC3101 I2C_SDA Q3202
IC2901 U20 C6 C2 C3 HPD HPD HPD
HM_HD I2C_SCK D8 LEVEL SHIFT 2 19
(2/2) T21 C7 D3
HM74CK
SOC P21 G1
(12/21) HMCK
T20 E1 IC3101 IC3202
HDMI PROCESSOR HDMI TRANSMITTER
XBB_SCK (14/21) (15/21)
OVERALL (3/7) (PAGE 3-3) F2
OVERALL (4/7) (PAGE 3-4) 8 BB_SO
D2
D3
ADA_LRCK
E11
ADA_BCK
OVERALL (4/7) E10
(PAGE 3-4) 13 ADA_FCK
D10
ADA_SIA0
C11
OVERALL (6/7) XPON_SW XCS_IC3101

(PAGE 3-6) 14 C30 T26
XHDMI_RST
A28
I2C_SCK
AR12
OVERALL (3/7) BB_SI I2C_SDA
(PAGE 3-3) 6 AR13
XHDMI_JACK_IN
H28
U2, R2, D2, E3, F1 - F4, G2, G4, AB12, AC11, AA10 - AA12,
AM16, AN16 AN15, AN22 - AN29, K34, K35, L32 - L34, K32,
L4, G3 H2 - H4, J3, J4, K2 - K4, AC15, AA13 AB10, AB11,

Y10 - Y12
M32, M33,
K33, J32
IC2701_DATA0 - IC2701_DATA7
IC2701_FLD, IC2701_VCLK,
H32, H33
IC2701_MCK, IC2701_LRCK
T2 - T4, U3, U4, V2 - V4,

L2, P3, P4, R1, R3, R4,
AM22 - AM29,
AR22 - AR29,
AP22 - AP29
W1 - W3
PCI_AD0 - PCI_AD31
AM17, AP15
PCI_XBE0 - PCI_XBE3
IC2701_ADATA
IC2101 J33 AA14
PCI_CLKRUN
(4/4) AM19 C3 IC2701
PCI_INTA
CPU AR20 E4 PCI PROCESSOR
PCI_PAR
(7/21, 9/21, 10/21) AM15 P2 (11/21)
PCI_XFRM
AN13 L3
PCI_XTRDY
AN14 N4
PCI_XSERR
AM13 N2
PCI_XDEVSEL
AM14 M2
PCI_XPERR
AN17 N3
PCI_XREQFS0
AM20 D4
PCI_XGNTTS0
AP17 D3
PCI_XSTOP
AR19 M3
PCI_XIRDY
AR21 N1
PCI_XRESET
AP19 M4
PCI_CLK
AR16 M1
AR17
IC2102
WAVEFORM SHAPER
FP-729 FLEXIBLE BOARD
A17, AC16
(7/21)
3 4 CLK_SYS_OUT
FP-724 ST-175 BOARD FLASH UNIT
B3
CN1025 FLEXIBLE (FL25500)
IC7291 A_2.8V
SIRCS_SIG OVERALL (6/7) BOARD
D_2.8V 1 REMOTE SENSOR 4 8
IR_LED_ON
Y3 X2101 15 (PAGE 3-6) L5201
T5201
D5202
CN5201
15 - 18
D30 12MHz XE_A
Q1001 IC2701_SYSCLK ST_UNREG 2 6
NS_LED_K L35 A15
2 CN1010 CN5202 1 +
STRB_CHARGE STRB_CHARGE SCHARGE_ON
D7291 R28 5 10 8 1 4 5 FLASH
NS_LED_A XSTRB_FULL XSTRB_FULL XSCHARGE_FULL
(NIGHT SHOT) 1 D_2.8V L19 6 9 7 UNIT
STROBO_ON IC5201 3
TALLY_LED_K XTALLY_LED 8 4 2 C5206
5 AM5 OVERALL (6/7) STROBE_ON
(PAGE 3-6) 16 7 FLASH
CONTROL/
CHARGING
CAPACITOR
XE_K
5-8
D7292 TALLY_LED_A CHARGE
4 D_2.8V CONTROL
(TALLY) Q5201
6 SWITCH
S001
ADAPTOR_DET ADAPTOR_DET ADAPTER DETECT ADAPTER DETECT
AP9 14 1 2
08
3-5
Ver. 1.1 2007.06
CN5305
LD-228 BOARD SHUTTER_XA
1
SHUTTER_XB
4
LENS BLOCK SHUTTER_A
SR5/SR5C/SR5E 3 LENS
IRIS CN5302 SHUTTER_B BARRIER
MOTOR 2
I_DRIVE- I_DRIVE- I_DRIVE- LENS_COVER_OPEN
1 J1 8 SR7/SR7E/SR8/SR8E
M I_DRIVE+
7
I_DRIVE+ I_DRIVE+
H1
LENS_COVER_LED_ON
9
I_HALL+ I_HALL+ I_HALL+
I_BIAS-
3 C5 CONTROL SWITCH BLOCK
I_BIAS- I_BIAS-
H 4 A5 (AD11800)
I_HALL- I_HALL- I_HALL- FP-717 FLEXIBLE BOARD
5 B6 (SR7/SR7E/SR8/SR8E)
I_BIAS+
2
I_BIAS+ I_BIAS+
C6
(SR7/SR7E/SR8/SR8E) CN7171
ND_DRIVE- ND_DRIVE- CN5306
8 L2 DIAL_B DIAL_B DIAL_B
1, 2
ND_BIAS- ND_BIAS- 1
9 A9 DIAL_A DIAL_A
ND_HALL- ND_HALL- 3
10 B11
ND_BIAS+ ND_BIAS+ S002
11 A11 S7171 Dial_B
ND_HALL+ ND_HALL+
12 C10 MANUAL CAMERA
ND_DRIVE+ ND_DRIVE+ CONTROL
14 K2
F_MR_A F_MR_A PON SW PON SW
21 B1 5 S001
F_MR_B F_MR_B Dial_A
19 C4
Z_MR_A Z_MR_A
18 E12 DIAL_A
5, 6
Z_MR_B Z_MR_B
16 E10
NF_DRIVE- NF_DRIVE-
32 L7
NF_DRIVE+
33 L6
30
NF_DRIVE+ FP-723 VC-504 BOARD (6/6) PNDCK
AC11
31 FLEXIBLE DIRB1
F21
BOARD DIRA1
CN5303 CN1012 E23
EN1
XPON_SW XPON_SW OVERALL (5/7) G22
43 3 14 (PAGE 3-5)
LENS TEMP TEMP_OUT LENS_TEMP_AD
SENSOR 23
ZOOM_A
24 SR7/SR7E/SR8/SR8E
ZOOM MOTOR ZOOM_A, ZOOM_XA, ZOOM_B DIAL_B DIAL_B
ZOOM_XB, ZOOM_B 25 45 1 A11
M ZOOM_XA DIAL_A DIAL_A
AA3, AC5 AA9, AB9, AC9, Y10, AB10,

AA2, Y2, W4, W2, Y1,
26 44 2 B11
J23, L22, J21, AA5, AA4, AB2, AA7, Y8, AA8, AB8, AC8,
AA11, Y12, AA12, AC13
V4, V2, W1, P2, P1,
FOCUS ZOOM_XB
N4, N2, N1, M4

MOTOR 27
FOCUS- IC5401 LENS_COVER_OPEN LENS_COVER_OPEN
FOCUS+, FOCUS- 28 1 FOCUS+_OUT 27 19 B5
M 29
FOCUS+
7 FOCUS DRIVE
2 F3 LENS_COVER_LED_ON
29 17
LENS_COVER_LED_ON
AB16
D24A00_CAM-D31A07_CAM,
(2/4) DXXA08_CAM - DXXA13_CAM
LENS_COVER_LED_ON
D_2.8V
LENS BLOCK
SR7/SR7E Q5301
IRIS CN5301
K4, L1, L4,

MOTOR I_DRIVE- /SR8/SR8E I_DRIVE- ALE_CAM, WR01_CAM, RDX_CAM,
J1, K1
1 XCS_IC1702_BUS, IC1702_BUS_CLK
M I_DRIVE+
7
I_DRIVE+ IC5404 SHUTTER_XA
F2 IC5801 C5 24 22
DIRB0
D12
I_HALL+ I_HALL+ ZOOM AND FOCUS SHUTTER_XB DIRA0
3 E6 SHUTTER C6 22 24 A13 AHS_TGHD, AHS_TGVD,
I_BIAS- I_BIAS- DRIVE SHUTTER_A IC1702
B5, B6
H 4 (2/4) F3 DRIVER EN0 AHS_XCS0, AHS_SCK, (3/3)
23 23 A14
K22, H23
I_HALL- I_HALL- SHUTTER_B (4/4) OVERALL (1/7) AHS_SO
5 D6
I_BIAS+
2
I_BIAS+ (PAGE 3-1) 2 CAMERA
SIGNAL
ND_DRIVE-
8 PROCESS
ND_BIAS- DIRB1 DIRB1 IC1803 OVERALL (5/7) STROBE_ON
9
ND_HALL-
J9
DIRA1
21 25
DIRA1 32BIT MASK-ROM (PAGE 3-5) 16 F23 (4/21)
10 M9 19 27
ND_BIAS+ L9, K9 (5/21)
11 EN1 EN1 OVERALL (4/7) EXT_STROBE_ON
12
ND_HALL+ 26 20
(PAGE 3-4) 12 H22
ND_DRIVE+ PNDCK PNDCK
14 K12 11 35
F_MR_A MD2
16 C1 E4
F_MR_B X1802 XCS_MC_FLASH
18 B17
Z_MR_A 20 MHz EEP_SI
20 AB14
D1
21
Z_MR_B
AC14
EEP_SO 5
NF_DRIVE- EEP_SCK
26 NF_EN NF_EN AB13 OVERALL (3/7)
L8 34 12 N22 AP_ENABLE
27 NF_SW NF_SW B18 (PAGE 3-3)
NF_DRIVE+ M8 33 13 N20
F2, F4
28 XIC5404_RST XIC5404_RST XSYS_RST
H11 38 8 B14
FOCUS 29
A10, D10 A4, C9
MOTOR IR_NOISE IR_NOISE CAM_VD_HS

FOCUS+ 28 18 P20 D7 AA6
FOCUS+, FOCUS- 24 TG_FLD
M 25
FOCUS-
E3 ND_NOISE
D13
EXT_CAM_VD
L21
ND_NOISE
31 15 A7 AC7
IC5402
ZOOM_XB CAM_SCK XCAM_SCK EXT_CAM_VD
48 1 LENS NOISE ZOOM_B_OUT H12 18 28 AB10
ZOOM_B 2 F1 CAM_SO CAM_SO SYS_V
ZOOM 50 7 FILTER J11 20 26 Y11 B8
MOTOR ZOOM_A, ZOOM_XA, (2/4) CAM_SI CAM_SI SSS
K11 17 29 AB11 AB5
ZOOM_XB, ZOOM_B XCS_IC5404 XCS_IC5404 XWEN
M J12 36 10 C22 AC5
ZOOM_XA IC5403 AB6
XHI_SCK 3
49 1 ZOOM_A_OUT XCS_IC1803
ZOOM_A LENS NOISE 2 K6 L12 AC6 OVERALL (2/7)
51 7 FILTER HI_SI
Y7 (PAGE 3-2)
(2/4) HI_SO
AB7
LENS TEMP TEMP_OUT LENS_TEMP_AD LENS_TEMP_AD LENS_TEMP_AD
23 32 14 R22
SENSOR THERM THERM THERM VST_C_RESET
31 35 11 T2
XRST_IC5703_CPU YAW_AD
39 7
XCS_EEP
F23 P23
PITCH_AD 1
F1 P22
PITCH_HALLBIAS+ (PITCH_IN+) CAM_SO OVERALL (1/7)
32 J3 A4 SR5/SR5C/SR5E (PAGE 3-1)
PITCH_HALL+ (PITCH_OUT+) CAM_SI
33 H2 B4 EEP_SI
YAW_HALL+ (YAW_OUT+) XCS_IC5404 1 IC1804 2
34 J9 A5 EEP_SCK
YAW_HALL- (YAW_OUT-) CAM_SCK 128K EEPROM 6
35 J7 B5 EEP_SO
YAW_HALLBIAS+ (YAW_IN+) SR7/SR7E/ (5/21) 5
36 G6 XRST_IC5703_CPU SR8/SR8E
YAW_HALLBIAS- (YAW_IN-) A6
37 J8
PITCH_HALLBIAS- (PITCH_IN-) XHIDS_RST XSYS_RST
38 J2 IC5703 A7 37 9
PITCH_HALL- (PITCH_OUT-)
39 J4
STEADYSHOT CAM_VD EXT_CAM_VD
46, 47 44, 45 42, 43 40, 41
PITCH+ PROCESSOR C9 25 21
B1
(3/4)
PITCH- YAW_AD YAW_AD
D1 J5 40 6
PITCH_AD PITCH_AD
G5 41 5
YAW- VST_C_RESET VST_C_RESET
D10 D5 42 4
YAW+ IC2701_SYSCLK IC2701_SYSCLK OVERALL (5/7)

B10 A3 13 33 15 (PAGE 3-5)
08
3-6
Ver. 1.1 2007.06
SP901
SPEAKER FP-546 FLEXIBLE
BOARD S001
PANEL
( REVERSE
DETECT )
1, 2 5, 6
CK-183 BOARD CN6003 CN6001
CN6005
FP-537 FLEXIBLE PD-324 BOARD
29, 30
SP
BOARD LCD901
PANEL_NOR/REV CN6004 CN6101 CN6105
28
PANEL_R PANEL_R PANEL_VR
5 22 22 34 20 4
PANEL_G PANEL_G PANEL_VG
4 23 23 33 21 5
PANEL_B PANEL_B PANEL_VB
3 24 24 32 22 3
1, 23, 24 2, 6 - 8, 11 - 14, 19 - 22
15, 19
15, 19
7, 11
1, 48
PANEL_VD, PANEL_HD PANEL_VD, PANEL_HD PANEL_RGT, PANEL_VP, PANEL_HCK1, PANEL_HCK2,
5 - 12, 14,
16, 24, 28
PANEL_REF, PANEL_HST, PANEL_PCG, PANEL_XSTBY,
BB_SI BB_SI PANEL_DWN, PANEL_EN, PANEL_VCK, PANEL_VST 2.7 inch : VIDEO SIGNAL
14 11 11 42 WIDE
BB_SO BB_SO COLOR
15 10 10 45 IC6102 : AUDIO SIGNAL
XBB_SCK XBB_SCK LCD
17 8 8 44 LCD DRIVE UNIT
XCS_LCD XCS_LCD
16 9 9 43
25, 26
PANEL_COM
Q6107, Q6110,
Q6112, Q6113,
BL_ON
18
BL_-V BACK EXTDA
31
LIGHT
DRIVE BL_L
BACKLIGHT
CN6102
TP_X TP_X TP_TOP
21 4 4 5
TP_Y TP_Y TP_L
19 6 6 2
TOUCH
TOUCH PANEL
TP_SEL1 TP_SEL1 TP_R
20 5 5 PANEL 1
I/F TP_BOT
4
FP-727 FLEXIBLE
TO VC-504 BOARD Q6101, Q6102
OVERALL (3/7)
(PAGE 3-3) CN6104 S004
KEY_AD0 KEY_AD HOME_SW HOME
8 18 18 2
2ND_ZOOM(W) S002
4 W W
2ND_ZOOM(T) S003 (ZOOM)
3 T
S6004 T
2ND_S/S_SW
KEY_AD2 5 S001
26
START/STOP
S6002 CONTROL KEY BLOCK
EASY
(SB22200)
CONTROL SWITCH BLOCK

S6006
(SB25500)
(FILM ROLL INDEX) CN6002 S7491

BACK_LIGHT
5, 6
BACKLIGHT
S6005
PANEL_O/C PANEL O/C
1
S6001
HI_XRESET RESET
25
S6003
XBATT_VIEW DISP/
27 BATT INFO
08
3-7
3-8. POWER BLOCK DIAGRAM (1/3) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
FP-721 FLEXIBLE VC-504 BOARD (1/3)

BOARD CN1009
ACV_UNREG ACV_UNREG_CN F4601 MT_BL_UNREG
3-8
J7212
DC IN BATT/XEXT BATT/XEXT_CN F4602 VTR2_UNREG
1
Q4601, Q4604, F4603 VTR_UNREG
Q4603 Q4610 Q4606, Q4607
F4605 SHOE_UNREG SHOE_UNREG
D4601 F4604 ST_UNREG ST_UNREG
SHOE_ON
FP-718 FLEXIBLE
BATT_LI_3V
INIT_CHARGE_ON
BOARD
FAST_CHARGE
CN7181 CN1013
BATT/XEXT_CR
G14, G15 H14, H15

35 7 PVDD1a
R1 VBATT
PVDD1b
D4702 LX1a L4701 L4719 D_1.2V_2
CRADLE
36 - 44
ACV_UNREG_CN R2 VCH
1-4
(Handycam Station) LX1b

IN1 H13 Q4713 L4722 A_1.2V_2
USB_DET USB_VCC MUTE
30 24 L4785 IC2701_D_1.2V
D2, D1 E2, E1
PVDD2a
F4606 BATT_UNREG PVDD2b
N1 B_UNREG L4702
B LX2a D_1.5V
D4605 LX2b
POWER (3/3)
(PAGE 3-10) BATT/XEXT IN2 E3
K14, K15 J14, J15

PVDD3a AFE_2.8V
Q4608
PVDD3b
L4703 L4714
P1, R5, L1, P15

BATT DVDD4 LX3a EP_2.8V
DETECT AVDD3 LX3b
VTR_UNREG Q4707
IN3 J13 L4720 D_2.8V
AVDD1 LOAD SWITCH
V_UNREG L4723 AU_2.8V
Q4724
P12, R12 P11, R11

PVDD4a L4725 A_2.8V
PVDD4b MUTE
LX4a L4704 L4715 EP_4.6V
LX4b L4721 AU_4.6V
IN4 N11
L4724 A_4.6V
B9, A9 B10, A10

PVDD5a
BATT_UNREG
VTR_UNREG
PVDD5b
LX5a L4705 L4726 MT_5.0V
LX5b
VO5_OUT
IN5 C8
FP-720 (1/2) FLEXIBLE BATT/XEXT
CN1017 C7 P71_INT01 P30_AN00 J5
BOARD
P9, R9 P10, R10

FAST_CHARGE PVDD6a POWER (2/3) (PAGE 3-9)
(1/2) E11 P53 P31_AN01 L6
INIT_CHARGE_ON PVDD6b A POWER (3/3) (PAGE 3-10)
BATT_UNREG_CN F10 P52 Q4708
1-6
L4706 L4716
B11, J2, K10, L10
+ AVCC LX6a D_1.8V

BH720 LOAD SWITCH
BATTERY BATT_SIG AVR LX6b
C 7 A4 SIO2 VOUT
TERMINAL M2 VOUT IN6 N10
VCC2
8 - 13
BATT_GND
-
VCC1
PVDD7a
G2, G1 F2, F1
PVDD7b
LX7a L4707 L4731 CMOS_4.1V
LX7b SR5/SR5C/SR5E
IN7 F3
1.8/3V_GATE_CTRL
IC4701 SR7/SR7E
Q4717, Q4720 /SR8/SR8E
POWER SUPPLY
(20/21) POWER REG
IC5101
DVDD1 A1
LANC PROCESSOR
DVDD2 A12
(21/21) VB VO5_OUT
VB B1
OUT11 R15 D4707
D4708
L4718 D_1.2V
B6, A6 B5, A5
PVDD8a
D4709
PVDD8b
L4708 L4784 A_1.2V
LX8a
LX8b Q4716
IC4706 IC4705
DVDD1
1.25V REG (20/21) MUTE 2.5V REG (20/21)
1.8/3VCTRL
VCC 5 1 CE D_2.5V
IN8 C7 4 OUT + 1 VOUT 3
4 VDD
Q4714 L4709 USB_3.3V
SWITCH
A_3.3V_LD
Q4721 - Q4723
OUT9-1 A13 Q4715 HDD_3.3V
SWITCH
OUT9-2 A14 MUTE
HDD_PON, XHDD_PON
G1, D1, D2
K13, L13, M13
P11_SO1 DIN CAP_IN A11

P12_SCK1 HI_EVER_SO, HI_EVER_SCK, XCS_DD CLK Q4709
1.8/3VCTRL
CLAMP_ON
P21_PPG01 LD A_3.3V
LOAD SWITCH
1.8/3V_GATE_CTRL L4712 D_3.3V
XLANC_PWR_ON CH9_SW1 C10
P07_INT11 C1 L3 WAKEUP Q4706 L4732
XLANC_ON BL_-V
P23 H2 M3 XCTL2 DVDD3 D15 SWITCH
BATT_IN OUT10-1 C15 Q4702

P70_INT00 A7 N2 CS_OUT
SD1 N9
VREF(2.5V) P5
CH6_SW N12
VRO P2 Q4703
VOUT3 B2
Q4701
BL_CONT
LOAD SWITCH SIG GEN
EVER_3.0V
CLAMP_ON
P22 G2 EP_8.5V
1.8/3VCTRL
P61_PPG11 C11
08
3-8
VC-504 BOARD (2/3) FP-727 CK-183 FP-537 PD-324 BOARD LCD901

FLEXIBLE BOARD FLEXIBLE
BOARD BOARD
CN1006 CN6005 CN6004 CN6101 Q6108, Q6109 CN6105
EP_8.5V EP_8.5V EP_8.5V EP_8.5V L6103 VDD
LCD POWER 2.7 inch
7 24 1 1 DRIVE 18
BL_-V BL_-V BL_-V BL_-V WIDE
9 22 3 3 COLOR
EP_4.6V EP_4.6V EP_4.6V EP_4.6V Q6107, Q6110,
22 9 17 17 LCD UNIT
EP_2.8V EP_2.8V EP_2.8V EP_2.8V Q6112, Q6113,
8 23 2 2
BACK
BL_L
BL_CONT BL_CONT BL_CONT BL_CONT LIGHT BACKLIGHT
19 12 14 14 DRIVE
L6102
A_3.3V A_3.3V L3202
L6101 IC6102
IC3202
D_1.8V D_1.8V L3258 LCD DRIVE
HDMI FB6101
D_3.3V D_3.3V L3255 TRANSMITTER
(15/21)
L3203
SR7/SR7E/SR8/SR8E
EP_2.8V L3701 FP-728 FLEXIBLE BOARD BL-013 BOARD

IC3702
FB3701 (SR7/SR7E/SR8/SR8E) (SR7/SR7E/SR8/SR8E)
EVF DRIVER LCD902
A_4.6V A_4.6V L3001
(17/21) CN3701 CN5901 CN5902 COLOR
IC3001 EP_8.5V L3703 EVF_VDD
A_2.8V A_2.8V L3002 D4_-2.8V L3003 1 20 2 EVF
D4 DRIVER UNIT
D_2.8V (13/21) L3702
EP_4.6V EP_4.6V D5901
19 2
(EVF BACK LIGHT)
D_3.3V FB3101
IC3101
D_2.8V FB3102
HDMI
FB3103 PROCESSOR FP-515 FLEXIBLE
D_1.5V D_1.5V BOARD HARD
(14/21) CN1004
DISK
FB1001 DRIVE
3 - 10
HDD_3.3V
VO5_OUT L4783 IC4702

D4_-2.8V CAM_-1.0V
D_2.8V
C2
-1.0V/-2.8V A3 C
REG
(20/21) POWER (3/3) CONTROL SWITCH BLOCK
A (PAGE 3-10)
(PS25500)
POWER (1/3) CN1003
(PAGE 3-8) HDD_3.3V HDD_3.3V ACCESS_LED_VDD D001
11
(ACCESS)
D002
EVER_3.0V EVER_3.0V CHARGE_LED_VDD
18 ( CHARGE/
STROBE )
D_2.8V D_2.8V MODE_LED_VDD D003

14 (PHOTO)
D_2.8V FB3301
D004
Q3301 (CAM)
MT_5.0V
SWITCH
RV001
D_2.8V D_2.8V
IC3301 9 T W
AU_4.6V L3304 VIDEO, AUDIO (ZOOM)
PROCESSOR
A_2.8V L3302 (16/21)
A_2.8V L3306
FP-719 FLEXIBLE
L3305 IC3201 BOARD
AU_2.8V
5V REG (15/21)
CN1021
CN7191
D_2.8V
1 CONT 5VPOWER_CN
3-4
D_2.8V FB2735 ST_UNREG VOUT 4 18 HDMI
6 VIN
D_1.8V FB2731
D_3.3V FB2734 IC2701

L2701 PCI
A_1.2V_2 A_1.2V_2 PROCESSOR
(11/21)
FP-724 FLEXIBLE ST-175 BOARD FLASH UNIT
A_1.2V_2 L2702
BOARD (FL25500)
IC2701_D_1.2V IC2701_D_1.2V FB2733
T5201
CN1010 CN5202 CN5201
L5201 D5202
15-18
12 - 14
ST_UNREG ST_UNREG XE_A
1-3
FLASH
UNIT
IC5201
VO5_OUT L1001 VO5_OUT MT_5V FLASH CONTROL/
9 6 CHARGE CONTROL
FP-725 FLEXIBLE
BOARD
CN1019
SHOE_UNREG SHOE_UNREG HOT
6, 7
SHOE
08
3-9
VC-504 BOARD (3/3) FP-723 LD-228 BOARD

FLEXIBLE IC5304 SR7/SR7E/SR8/SR8E
LENS BLOCK
BOARD 2.8V REG (1/4)
CN1012 CN5303 CN5301
A_3.3V_LD A_3.3V_LD A_3.3V_LD L5301 MR_A_2.8V F_MR_VCC
45 1 4 IN OUT 3 15
D_1.5V D_1.5V D_1.5V

44 2 Z_MR_VCC
19
41, 42
MT_5.0V MT_5.0V MT_5.0V
4, 5
D_2.8V D_2.8V IC5401
43 3 FOCUS DRIVE (2/4)
SHOE_ON
AP11 EXIO/CF_ADDR[9]
L5401
AR6, AM6
HDD_PON, XHDD_PON EXIO_DREQ 8 VCC SR5/SR5C/SR5E LENS BLOCK
EXIO_DACK CN5302
FB2180 Z_MR_VCC
USB_3.3V SR5/SR5C/SR5E 15
D_3.3V
MT_5.0V IC5404 F_MR_VCC
20
ZOOM AND FOCUS MR_A_2.8V
D_2.8V FB2504 D_2.8V FB5401 DRIVE
(2/4)
FB2505 IC2101
CPU
IC1007 IC5402 IC5403
(7/21, 9/21, 10/21)
FB2501 MEMORY STICK 2.9V REG LENS NOISE FILTER (2/4)
D_1.2V (1/21)
FB2181 MS_PWR_ON MT_5.0V
GPIO_S[14] H20 1 CE FB1008 8 VCC
FB2502 D_3.3V D_1.5V
D_1.8V 4 VDD VOUT 3 IC5703
MT_5.0V L5701
FB2503 STEADYSHOT
PROCESSOR
L2102 B D_2.8V (3/4)
A_1.2V USB_VCC
Q1004 POWER (1/3)
L2501 XVBUS_DET
GPIO_S[2] G25 (PAGE 3-8) D_2.8V IC5801 SR7/SR7E/SR8/SR8E
D_2.5V
L5801 SHUTTER DRIVER
A_2.8V FB2101 (4/4)
FB2102
D_3.3V
D_2.8V
FP-720 (2/2) MS-374
BATT_LI_3V
FLEXIBLE BOARD
CN1017
BOARD
D_1.2V
D_1.8V
CN7401 CN7402
A_2.8V
IC1804
D_2.8V (2/2)
MEMORY
17, 18
128K EEPROM MS_VCC MS_VCC VCC
FB2201 IC2201 (5/21) 16 9 STICK
A 512M SDRAM,
DUO
FB2202 D_2.8V D_2.8V
POWER (1/3) 512M OneNAND FLASH 15 19 CM-077 BOARD (SR7/SR7E/SR8/SR8E)
(PAGE 3-8) (8/21) D_2.8V
IC1803 D7401
BATT_LI_3V BH7401 L7201
FB1802 32BIT MASK-ROM 32 1 (ACCESS) IC7201
D_1.2V_2 3V
(5/21) PITCH/YAW
SENSOR AMP
D_1.2V D_1.2V
FB1702 IC6603 L6706
D_2.5V 4 IN OUT 3
L1702 3.3V REG L6704
IC1702
A_1.2V L1703 CAMERA SIGNAL
PROCESS
L1704 IC6604 D_2.8V
AFE_2.8V (4/21) 4 IN OUT 3
2.8V REG
D_2.8V FB1701
IC6701
IC6605 A_3.3V L6702
FB1901 IC1901 4 IN OUT 3 CMOS IMAGER
D_2.5V SR7/SR7E/
256M 32BIT SDRAM SR8/SR8E L1202 3.3V REG L6705
AFE_2.8V IC1201
A_2.8V (6/21)
TRIPLE CHANNEL L6707
D_2.8V L1201 ADC_1 CN6601 IC6606 D_1.8V
(2/21) A_2.8V 4 IN OUT 3
10 1.8V REG
CMOS_4.1V A_4.1V
IC1902
SR5/SR5C/ 14
SR7/SR7E/SR8/SR8E CAM_-1.0V A_-1.0V A_-1.0V
128M 16BIT SDRAM SR5E 15
(6/21) L1302
AFE_2.8V IC1301
TRIPLE CHANNEL CM-076 BOARD (SR5/SR5C/SR5E)
D_2.8V L1301 ADC_2
SE3801
(3/21) CN6801
A_2.8V A_2.8V L8201 IC8201
G-SENSOR SR5E/SR7/ 10
SR7E/SR8/SR8E CMOS_4.1V A_4.1V PITCH/YAW
14
CAM_-1.0V A_-1.0V SENSOR AMP
15
SE3802 IC6801 L6907
L1701 IC1701 4 IN OUT 3
SR5/SR5C A_2.8V 3.3V REG L6911
G-SENSOR FF
(4/21)
CN1201 IC6802 D_2.8V
A_2.8V A_2.8V 4 IN OUT 3
31 2.8V REG
CMOS_4.1V CMOS_4.1V
27
CAM_-1.0V CAM_-1.0V
26
C IC6803 L6914
IC6901
L2904 A_3.3V CMOS IMAGER
A_2.8V POWER (2/3) 4 IN OUT 3
(PAGE 3-9) 3.3V REG L6909
FB2954
D_1.2V_2
IC2901 L6912
A_1.2V_2 L2903
CN1001 SOC
D_3.3V (12/21) IC6804 D_1.5V
16 L2952 4 IN OUT 3
CPC D_2.8V 1.5V REG
9
A_-1.0V
(For check)
08
3-10E
Ver. 1.1 2007.06 4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM

4-1-1. HDR-SR5/SR5C/SR5E
LENS BLOCK
LEVEL3 LEVEL3
ST-175 BOARD ST-175 BOARD FP-546 FLEXIBLE BOARD
(SIDE A) (SIDE B) LD-228 BOARD (SIDE A) LD-228 BOARD (SIDE B)
CONTROL
SWITCH
18
BLOCK
FLASH UNIT
CN5201
33 1 (SB25500)
(FL25500) 32 CN5302 2
1 2
1
14
CN5202 2
13 1
CN5303
45 44
FP-712 CN6002
6 1
FLEXIBLE 1 6
10
BOARD LENS
CN5305
24
1
BARRIER
1
CN6004
CN6005
FP-712 flexible board is not supplied,
but this is included in LENS BARRIR UNIT.
1
30
CN6001
6
1
11
1
TO CRADLE
(Handycam Station)
CN7402 J7212 IC6901

(not supplied) 1 24
DC IN CN6101
1 41
J7211 2 CN7181 42
REMOTE LEVEL3
JACK
10
12 CM-076 BOARD LEVEL3
(SIDE B) CM-076 BOARD
MS-374 BOARD CK-183 BOARD PD-324 BOARD
31
1 CN6801 30
32 (SIDE A) (SIDE B) (SIDE A)
FP-718
CN6003
(SIDE A) 1 SP901 CK-183 BOARD
FLEXIBLE 2 SPEAKER
(SIDE A)
FP-721 BOARD 1 6
MS-374 BOARD FLEXIBLE 1 24 1 6 CN6104
(SIDE B) BOARD CN6105 CN6102
BT7401
CONTROL
20
HARNESS (COAXIAL CABLE)

19
LITHIUM SECONDARY
51 1
BATTERY W
KEY
CN7401
2.7 INCH
WIDE COLOR
TOUCH T BLOCK
PANEL
LCD UNIT (SB22200)
2
1
LEVEL3 LCD901
VC-504 BOARD (SIDE B)
2 CN1012 44
1 51 CN1013 1 1 45
CN1006
30 1
50 2
CN1009
42 41
40 CN1201 1
20
14
13
CN1010
2
1
FP-729
BH720
C BATTERY
8
FLEXIBLE
CN1025
8
TERMINAL
LEVEL3 BOARD
VC-504 BOARD 1
32
1
31
(SIDE A) 1 2
FP-720 IC1804
18
17
CN1017
(EEPROM)
FLEXIBLE
CN1004
CN1001
CPC
BOARD (For Check)
1
2
1
1
1
2
1
FP-719 51 50
CN1026
23 22
CN1021
IC2201
JK-342 BOARD
19
FLEXIBLE (not supplied)
CN7191
(SIDE A) BOARD
1 20 1 14
CN7302 26 CN1003 CN1019 24 24
1 6
A/V OUT 1 CN1020
14 13
10
21 20
CN7302
5
9
4
8
3
7
2
6
1
12 11
40
26
CN7301 FP-726 FLEXIBLE CONTROL 1

HARD DISK
COMPONENT OUT 14 13 SWITCH MIC901 DRIVE
BOARD
CN7303
CN7301
10 MICROPHONE
BLOCK UNIT FP-515 FLEXIBLE
12
1
11
(PS25500) BOARD
51
1
FP-725
FLEXIBLE
BOARD HOT SHOE
Active
Interface Shoe
4-1 FRAME
Ver. 1.1 2007.06
4-1-2. HDR-SR7/SR7E/SR8/SR8E
FP-717 FLEXIBLE BOARD CONTROL
CN7171
SWITCH
6
6
BLOCK
1
1
(AD11800)
LEVEL3 LEVEL3
ST-175 BOARD ST-175 BOARD FP-546 FLEXIBLE BOARD
(SIDE A) (SIDE B) LD-228 BOARD (SIDE A) LD-228 BOARD (SIDE B)
CONTROL
SWITCH
18
BLOCK
FLASH UNIT
CN5201
(SB25500)
(FL25500) LENS BLOCK
1 2
1 2
1
14
CN5202 2
13 1
CN5303
CN5301
CN5306
6
1
45 44
FP-712 CN6002
6 1
51 50
FLEXIBLE 1 6
10
BOARD LENS
CN5305
24
1
BARRIER
1
CN6004
CN6005
FP-712 flexible board is not supplied,
but this is included in LENS BARRIR UNIT.
1
30
CN6001
6
1
11
1
TO CRADLE
(Handycam Station) LEVEL3
CN7402 J7212
CM-077 BOARD IC6701
DC IN (SIDE B) (not supplied) 1
CN6101
24
1 41
J7211 2 CN7181 42
REMOTE
10 JACK
12
MS-374 BOARD CK-183 BOARD PD-324 BOARD

FP-718 1
CN6601 40
(SIDE B) (SIDE A)
CN6003
(SIDE A) 41 42
1 SP901 CK-183 BOARD
FLEXIBLE 2 SPEAKER
(SIDE A)
FP-721 BOARD 1 6
MS-374 BOARD FLEXIBLE LEVEL3 1 24 1 6 CN6104
(SIDE B) BOARD CM-077 BOARD CN6105 CN6102
(SIDE A)
BT7401
CONTROL
20
HARNESS (COAXIAL CABLE)

19
LITHIUM SECONDARY
51 1
BATTERY W
KEY
CN7401
2.7 INCH
WIDE COLOR
TOUCH T BLOCK
PANEL
LCD UNIT (SB22200)
2
1
LEVEL3 LCD901
VC-504 BOARD (SIDE B)
2 CN1012 44
1 51 CN1013 1 1 45
CN1006
30 1
50 2
CN1009
42 41
40 CN1201 1
20
14
13
CN1010
2
1
FP-729
BH720
C BATTERY
8
FLEXIBLE
CN1025
8
TERMINAL
LEVEL3 BOARD
1
VC-504 BOARD
32
1
31
12
(SIDE A)
CN1022
1 2
FP-720 IC1804
18
17
CN1017
(EEPROM)
1
FLEXIBLE
CN1004
CN1001
CPC
BOARD (For Check)
1
2
1
1
1
2
1
FP-719 51 50
CN1026
23 22
CN1021
IC2201
JK-342 BOARD 20
CN3701
2
19
FLEXIBLE (not supplied)
CN7191
19 1
(SIDE A) BOARD
1 20 1 14
CN7302 26 CN1003 CN1019 24 24
1 6
A/V OUT 1 CN1020
14 13
10
21 20
CN7302
5
9
4
8
3
7
2
6
1
12 11
40
26
CN7301 FP-726 FLEXIBLE CONTROL

1
HARD DISK
COMPONENT OUT 14 13 SWITCH J7222 MIC901 DRIVE
BOARD FP-722
CN7303
CN7301
10 MICROPHONE
BLOCK MICROPHONE
UNIT FP-515 FLEXIBLE
(PS25500) FLEXIBLE JACK
12
1
11 BOARD BOARD
51
1
J7221
FP-725 HEADPHONE
BL-013 BOARD FLEXIBLE JACK
(SIDE A) BOARD Active

HOT SHOE
Interface Shoe
20
1 2
CN5902
CN5901
LCD902
COLOR
EVF UNIT 21 20
1
4-2 FRAME
Ver. 1.1 2007.06
4-2. SCHEMATIC DIAGRAMS
Link

CK-183 BOARD (CONTROL SWITCH) (REMOTE, DC IN)
PD-324 BOARD (LCD DRIVE) : SR7/SR7E/SR8/SR8E (HP, MIC JACK)
JK-342 BOARD (JACK) (LD-VC CONNECTION)
ST-175 BOARD (FLASH DRIVE) (VC-ST CONNECTION)
MS-374 BOARD (MS CONNECTOR) (HOT SHOE CONNECTION)
BL-013 BOARD : SR7/SR7E/SR8/SR8E FP-726 FLEXIBLE BOARD
(EVF, EVF BACKLIGHT) (VC-JK CONNECTION)
FP-515 FLEXIBLE BOARD FP-727 FLEXIBLE BOARD
(HDD CONNECTION) (VC-CK CONNECTION)
(CK-PD CONNECTION) : SR7/SR7E/SR8/SR8E(BL-VC CONNECTION)
(PANEL REVERSE DETECTION SWITCH) (REMOTE SENSOR)
FP-712 FLEXIBLE BOARD CONTROL SWITCH BLOCK (AD11800)
(LENS BARRIER) : SR7/SR7E/SR8/SR8E
FP-717 FLEXIBLE BOARD : SR7/SR7E/SR8/SR8E
(MANUAL CONTROL SWITCH) CONTROL SWITCH BLOCK (PS25500)
(CRADLE TERMINAL) CONTROL SWITCH BLOCK (SB25500)
(HDMI CONNECTOR) CONTROL KEY BLOCK (SB22200)
(BATTERY TERMINAL) FLASH UNIT (FL25500)
COMMON NOTE FOR SCHEMATIC DIAGRAMS SIGNAL LOCATION
4-2. SCHEMATIC DIAGRAMS ENGLISH JAPANESE

(ENGLISH)
THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS
(In addition to this, the necessary note is printed in each block)
(For schematic diagrams) 1. Connection

• All capacitors are in µF unless otherwise noted. pF : µ
Pattern box Color bar chart
µF. 50 V or less are not indicated except for electrolytics
and tantalums. Pattern box PTB-450 For PTB-450:
J-6082-200-A J-6020-250-A
• Chip resistors are 1/10 W unless otherwise noted.
or
kΩ=1000 Ω, MΩ=1000 kΩ. Small pattern box For PTB-1450:
• Caution when replacing chip parts. PTB-1450 J-6082-559-A
New parts must be attached after removal of chip. J-6082-557-A
Be careful not to heat the minus side of tantalum
capacitor, Because it is damaged by the heat.
L = 1 m (PTB-450)
• Some chip part will be indicated as follows. L = 40 cm (PTB-1450)
Example C541 L452
22U 10UH Pattern box
Front of the lens
TA A 2520
L Camera
Kinds of capacitor External dimensions (mm)
Case size
• Constants of resistors, capacitors, ICs and etc with XX
indicate that they are not used.
In such cases, the unused circuits may be indicated. 2. Adjust the distance so that the output waveform of
• Parts with ★ differ according to the model/destination. Fig. a and the Fig. b can be obtain.
Refer to the mount table for each function.
H
• All variable and adjustable resistors have characteristic Yellow
Magenta
White
curve B, unless otherwise noted. Cyan
• Signal name Green
Red
Blue
XEDIT → EDIT PB/XREC → PB/REC
• 2: non flammable resistor
• 5: fusible resistor
• C: panel designation
• A: B+ Line
• B: B– Line A B A=B B A
• J : IN/OUT direction of (+,–) B LINE. Fig. a (Video output terminal output waveform)
• C: adjustment for repair.
Electronic beam scanning frame
(Measuring conditions voltage and waveform)
• Voltages and waveforms are measured between the
measurement points and ground when camera shoots
color bar chart of pattern box. They are reference values
and reference waveforms. CRT picture frame
(VOM of DC 10 MΩ input impedance is used)
• Voltage values change depending upon input
impedance of VOM used.)
Fig.b (Picture on monitor TV)
Precautions for Replacement of Imager
• If the imager has been replaced, carry out all the adjustments When indicating parts by reference number, please
for the camera section. include the board name.
• As the imager may be damaged by static electricity from
its structure, handle it carefully like for the MOS IC. The components identified by mark 0 or dotted line with
In addition, ensure that the receiver is not covered with mark 0 are critical for safety.
dusts nor exposed to strong light. Replace only with part number specified.
Les composants identifiés par une marque 0 sont

critiques pour la sécurité.
Ne les remplacer que par une pièce portant le numéro
spécifie.
4-3
4-2. SCHEMATIC DIAGRAMS ENGLISH JAPANESE
(JAPANESE)
回路図共通ノート
（他に必要なノートは各ブロックに記載してあります）
【回路図ノート】 1. 接続図
・ケミコン，タンタルを除くコンデンサで，耐圧50V以下のもの
パターンボックスカラーバーチャート
はその耐圧を省略。単位はすべてμF（pはpF）。
・チップ抵抗で指示のないものは，1／10W以下。 Pattern box PTB-450 For PTB-450:
kΩ＝1000Ω，MΩ＝1000kΩ J-6082-200-A J-6020-250-A
or
・チップ部品交換時の注意 Small pattern box For PTB-1450:
取り外した部品は再使用せず，未使用の部品をご使用くださ PTB-1450 J-6082-559-A
い。 J-6082-557-A
タンタルコンデンサのマイナス側は熱に弱いため注意してくだ
さい。 L = 1 m (PTB-450)
・チップ部品には下記のように表示したものがあります。 L = 40 cm (PTB-1450)
　例 C 541 L 452 パターンボックス
レンズ前面
22U 10UH
TA A 2520
L カメラ
↑ ↑ ↑
種類ケースサイズ外形寸法（mm）
・抵抗，コンデンサ，ICなど定数にXXがあるものは，使用して
いない事を示しています。このため，使用していない回路が記
載されている事があります。 2. 図a及び図bの波形が得られるように画枠調整して下さい。
・★印のある部品は，機種などにより異なりますので機能別マウ
ント一覧表を参照してください。 H
・可変抵抗と半固定抵抗で，B特性の表示を省略。シマ
ゼ
・信号名表記について，下記のような場合があります。黄ア
ン白ン
XEDIT　→　EDIT　　　　　PB/XREC　→　PB/REC 緑ダ赤
・2は不燃性抵抗。青
・1はヒューズ抵抗。
・Cはパネル表示名称。
・AはB＋ライン。
・BはB−ライン。 A B A=B B A
・JはBライン（＋，−）の入出力方向を示す。図a（映像入出力端子出力波形）
・Cは調整名称。
電子ビーム走査線
【電圧・波形測定条件ノート】
・電圧値及び信号波形はパターンボックスのカラーバーチャート
を被写体としたときの測定点対アース間の参考値。
（デジタルマルチメータ；入力インピーダンス　DC10MΩ使
用）ブラウン管の画像枠
・使用テスタの入力インピーダンスにより電圧値が多少異なりま
す。
図b（テレビモニタの映像）
イメージャ交換時の注意
・イメージャを交換した場合は，カメラ部の全調整を 0印の部品，または0印付きの点線で囲まれた部品は，
行ってください。安全性を維持するために重要な部品です。
・イメージャは構造上，静電気により破壊される恐れが従って交換時は，必ず指定の部品を使用して下さい。
あるため，MOS ICと同様に注意して取り扱ってくださ
お願い
い。
図面番号で部品を指定するときは基板名又はブロック
また，受光部にはゴミの付着，および強い光がはいるを併せて指定して下さい。
ことのないように注意してください。
4-4
Schematic diagrams of the CM-076, CM-077, VC-504 and LD-228 boards are not shown.
Pages from 4-5 to 4-31 are not shown.
1 2 3 4 5 6 7 8
CN6001 6P
1 REG_GND
A 2 REG_GND
FP-546 S6005 A
(PANEL OPEN/CLOSE)
3 N.C. FLEXIBLE
LND001-LND006 1 C 2
4 N.C. PAGE 4-39 PANEL_O/C
of LEVEL 2 3 4
5 PANEL_REV
6 PANEL_REV LND601
D6005
D6001 CH GND
XX SP+ 30 SP+
XX
SP- 29 SP-
PANEL_NOR/REV PANEL_NOR/REV 28 PANEL_NOR/REV

S6001
24P CN6004 XBATT_VIEW 27 XBATT_VIEW
EP_8.5V 1 EP_8.5V KEY_AD2 26 KEY_AD2
HI_XRESET
EP_2.8V 2 EP_2.8V HI_XRESET 25 RESET
RESET
B BL_-V 3 BL_-V EP_8.5V 24 EP_8.5V B
TP_X 4 TP_X EP_2.8V 23 EP_2.8V
TP_SEL_1 5 TP_SEL_1 BL_-V 22 BL_-V
TP_Y 6 TP_Y TP_X 21 TP_X
REG_GND D6008 TP_SEL_1
7 MAZS068008SO TP_SEL_1 20
XBB_SCK 8 XBB_SCK TP_Y 19 TP_Y
D6002
XX XCS_LCD 9 XCS_LCD 18 REG_GND
BB_SO BB_SO XBB_SCK
FP-727
10 17 XBB_SCK
FLEXIBLE
FP-537 BB_SI 11 BB_SI XCS_LCD 16 XCS_LCD LND101-LND130
REG_GND FLEXIBLE REG_GND PAGE 4-46
LND001-LND024 12 BB_SO 15 BB_SO
of LEVEL 2
SP901 PAGE 4-39
of LEVEL 2 REG_GND 13 BB_SI 14 BB_SI
SPEAKER
CN6003 2P BL_CONT 14 BL_CONT 13 REG_GND
SP(+) 1 SP+ PANEL_VD 15 PANEL_VD 12 BL_CONT

C BL_CONT C
SP(-) 2 SP- D_2.8V 16 D_2.8V PANEL_VD 11 PANEL_VD
EP_4.6V 17 EP_4.6V D_2.8V 10 D_2.8V

D6003 D6004 2nd S/S KEY_AD0
18 EP_4.6V 9 EP_4.6V
XX XX
PANEL_HD 19 PANEL_HD KEY_AD0 8 (2nd S/S,Zoom)
LND602
REG_GND 20 PANEL_HD 7 PANEL_HD
CH GND
REG_GND 21 6 REG_GND
PANEL_R 22 PANEL_R PANEL_R 5 PANEL_R
PANEL_G 23 PANEL_G PANEL_G 4 PANEL_G
PANEL_B 24 PANEL_B PANEL_B 3 PANEL_B
REG_GND 2 REG_GND
CN6002 6P
1 REG_GND PANEL_O/C 1 PANEL_OPEN/CLOSE
REG_GND
2 REG_GND CONTROL CN6005 30P
D SWITCH BLOCK D
3
(SB25500)
4 LND001-LND006
5 BACK_LIGHT PAGE 4-49
of LEVEL 2
6 BACK_LIGHT
KEY_AD2
R6001 R6002
R6003 6800 2700
36k
S6006 1 2 1 2 1 2
D6007
XX
(FILM ROLL INDEX) 3 4 3 4 3 4
S6002 S6004
EASY
E E
1 2
XBATT_VIEW
D6006
3 4 XX
S6003
DISP/
BATT INFO LND603
CH GND
F CK-183 BOARD F
CONTROL SWITCH
XX MARK:NO MOUNT
08
4-32 CK-183
Ver. 1.1 2007.06
1 2 3 4 5 6 7 8 9 10 11 12
Q6109
MCH6305-TL-E-S
LCD POWER DRIVE
10uH
L6103 8.5 6 8.5
10uH
EP_8.5V 5
L6102 4 2
EP_4.6V 1
BIN FB6101 R6133 C6124
PANEL_B 24 10uH 0.01u
EP_2.8V 100k
A PANEL_G 23 GIN L6101
0uH 5.8 3 B
25V
A
PANEL_R 22 RIN
C6103 C6105 C6107 C6110 C6111 C6112 C6116 C6117
REG_GND 21 10u 22u 2.2u XX 0.1u 22u 1u 1u R6135
B 4V B 4V B 6.3V B B 220k
REG_GND 20 6.3V P 6.3V P 10V P 16V 16V D6104
2012 1608 1608 1608 XX
PANEL_HD 19 PANEL_XHD
REG_GND
KEY_AD 18 KEY_AD R6131 0
EP_4.6V XX 2.8
EP_4.6V 17
PANEL_XSTBY
D_2.8V 16 D_2.8V 24 COM
Q6108
PANEL_VD 15 PANEL_XVD C6122 UNR32A300LS0 PANEL_COM 23 CS
C6113 B
BIN 0.01u 25V XX LCD POWER DRIVE
BL_CONT 14 BL_CONT PANEL_REF PANEL_VST 22 VST
C6114 B
GIN C6119 4.7u B
FP-537 REG_GND 13
0.01u 25V
PANEL_VCK 21 VCK
C6115 B 6.3V 2012
FLEXIBLE RIN 0.01u 25V
LND301-LND324 REG_GND 12 C6120 10u B PANEL_EN 20 EN
EXTDA 6.3V 2012 PANEL_COM
PAGE 4-39 BB_SI 11 BB_SI R6115 PANEL_DWN 19 DWN
B of LEVEL 2 10k
0.5% R6122 10k B
2.8
2.2
2.0
BB_SO
2.8
BB_SO 10
1.0
1.0
1.4
4.0
18 VDD
1.0
2.6
1.2
REG_GND
XCS_LCD 9 XCS_LCD R6137 17 VSS
C6123 120k C6125
36 35 34 33 32 31 30 29 28 27 26 25 1u R6145
XBB_SCK 8 XBB_SCK B 10V D6105 1M 16 N.C.
0
COM
COMDA
10V B
COMREF
1608
VCC1
XLED
EXTDA
REF
RIN
GIN
BLDET
BIN
C6121
FILTER
REG_GND 7 1u Q6111 15 VSSG
0.1u 1608 -5.5 MAZS056008S0 LCD901
B 2SA207800LS0
TP_Y 6 TP_Y 10V PANEL_XSTBY 14 XSTBY 2.7inch
LOAD SWITCH WIDE
TP_SEL_1 5 TP_SEL1 PANEL_PCG 13 PCG COLOR
R6112 91k LCD
TP_X 4 TP_X 0.5% 1.3 0 PANEL_HST 12 HST UNIT
C6126
48 47 46 45 44 43 42 41 40 39 38 37
13 14 15 16 17 18 19 20 21 22 23 24
FILTER2 VP PANEL_VP
BL_-V 3 BL_-V 4.7 11 REF
B
C6108 GND1 VCC2 0.1u
EP_2.8V 2 EP_2.8V 1.1 2.5 R6125 XX PANEL_REF 10 TEST1
0.1u C6109
B 560p OPOUT VB PANEL_VB
EP_8.5V 1 EP_8.5V 1.4 2.5 R6126 XX 9 TEST2
CH
R6109 1608 OPIN VG PANEL_VG
24P CN6101 68k 2.5 R6128 XX PANEL_HCK2 8 HCK2
TEST VR PANEL_VR
LD6101 R6107 XX 1.1 PANEL_HCK1 7 HCK1
BB_SI SO IC6102 GND2
C CH_GND REG_GND R6108 XX 2.7 CXM3006CR-T4 2.8 PANEL_VP 6 PSIG C
XCS_LCD XCS LCD DRIVE PWM BL_ON
R6110 470 2.6 PANEL_VG 5 G
XBB_SCK XSCK WIDE
R6111 XX 0 0 PANEL_VR 4 R
BB_SO SI VST PANEL_VST
2.8 2.8 PANEL_VB 3 B
VDD VDD
1.4 PANEL_RGT 2 RGT
SCAN VCK PANEL_VCK
2.6 PANEL_COM 1 COM
PANEL_XHD XHD VSS
CN6105 24P
R6104
XX CN6103 0
1005
REG_GND/HOME_SW 1 KEY_AD
XSTBY
CLKIN
XCLR
HCK1
HCK2
DWN
2ND_ZOOM(W) 2
XVD
RGT
PCG
VSS
HST
R6101
EN
R6102
2ND_ZOOM(T) 3 1500
2200 1005 REG_GND
2ND_S/S_SW 4 1 2 3 4 5 6 7 8 9 10 11 12
0
1005 R6103 R6105
1.1
N.C. 5 XX 1200
R6152
0
0
1005
2.8
2.8
2.8
1.4
1.4
2.5
1005 PANEL_XVD PANEL_EN
D REG_GND 6 LD6102
D
PANEL_DWN R6146 XX
LED_1A LED_1A
PANEL_XSTBY
PANEL_PCG D6106
NSSW008DT-T108
PANEL_HST
R6121 XX (LDC BACKLIGHT)
PANEL_HCK2 R6147 XX
6P CN6104
D6102 R6123 XX
REG_GND 6
0
XX PANEL_HCK1
CONTROL KEY 2ND_S/S_SW 5 PANEL_RGT
R6153
BLOCK 2ND_ZOOM(W) 4
(SB22200) R6148 XX LD6103
LND001-LND006 2ND_ZOOM(T) 3 LED_2A LED_2A
PAGE 4-49 HOME_SW 2
of LEVEL 2 D6107
REG_GND 1 R6106 XX
NSSW008DT-T108
EP_4.6V
(LDC BACKLIGHT)
BL_-V R6149 XX
E E
R6119 R6124 R6127 R6129
0
C6106 R6118
REG_GND XX XX XX XX XX
XX
R6154
R6150 XX LD6104
LED_3A LED_3A
NC 6
TP_X D6108
TP_TOP 5 TP_X
BL_ON R6120 Q6104 Q6105 Q6106 NSSW008DT-T108
TP_BOT
TP_BOT 4 XX XX XX XX (LDC BACKLIGHT)
TOUCH IC6101 R6113
PANEL XX R6151 XX LD6105
NC 3 XX
TP_Y LED_C
TP_L 2 TP_Y R6116
0
Vcc 6 3
TP_R 2.8 XX LED_2A LED_1A LED_3A
8
EP_8.5V A_OUT
1608
TP_R 1 TP_SEL1
R6155
5 B_OUT 2 5
7
6P CN6102 A_IN-
C6104 B_IN-
6
C6118 R6117 1 4
2.8 2.8 XX A_IN+ XX Q6103 BL_L
B_IN+ XX
5
D_2.8V R6114 XX
03 4 GND
F 6
Q6101 XX F
1 XP411F-TXE
TOUTCH
PANEL I/F REG_GND
2
3
2
1
2.8 Q6102 EXTDA

5 XP421F-TXE
TOUTCH
0 PANEL I/F
4
3 D6103
1
4
5
6
6 XX
2.8 Q6110
D6101 C6102 UP04601008S0
C6101
XX 0.0047u 0.0047u 2 0 BACKLIGHT DRIVE
B B
EP_2.8V
REG_GND
EXTDA R6139
4700 R6140 R6142
R6136 0.5% 2.2k 2.2k
BL_ON
47k Q6112
G 2.8 0.5%
1005
2.1 UP04401008S0 G
2.8 6 4 2.7 2.1 1 4
1005 BACKLIGHT DRIVE
Q6107 2.8
2 5 2 1.6
UNR31A300LS0
BACKLIGHT DRIVE 5
R6134 2.7
13 1.0 1.6 6 3 1.0
1.0 47k 2.2
0.5%
BL_CONT 1005
R6130
3k R6138
R6132 100k
0.5% 22k
REG_GND REG_GND
R6143
100k
1.6 64 -9.8
Q6113
UP04601008S0 2 5
BACKLIGHT DRIVE BL_L
H 0 H
-9.8 13 R6144
0
PD-324 BOARD
R6141 10
1k 0.5%
0.5% 1608
BL_-V
LCD DRIVE
XX MARK:NO MOUNT
08
4-33 PD-324
1 2 3 4 5 6 7 8
R7301 XX
SW 10 XD3_CN
R7302 XX
A SW_GND 9 LINE_CNT3 A
1314 R7303 XX
CTRL3 8 LINE_CNT2
R7304 XX
CTRL2 7 LINE_CNT1
COMPONENT CTRL1 6 FB7305

PR 5 D3_LNO_PR
OUT FB7306
PBPR_GND 4 FB7307 D3_LNO_PB
PB 3 D3_LNO_Y
1112 CN7303 26P
6
5
4
Y_GND 2
REG_GND 1 REG_GND
Y 1
D3_LNO_Y 2 D3_LNO_Y
10P CN7301
3 REG_GND
3
2
1
1
2
3
4 D3_LNO_PB
B D3_LNO_PB
B
REG_GND 5 REG_GND
D7301 D7302 D3_LNO_PR
D3_LNO_PR 6
NSAD500H-T1-A XX
7 REG_GND
LINE_CNT1 8 LIN_CNT1
XD3_CN 11 XD3_CN
12 REG_GND FP-726
AUDIO_L_I/O 13 AUDIO_L_I/O FLEXIBLE
LND101-LND126
14 REG_GND
PAGE 4-46
AUDIO_R_I/O of LEVEL 2
AUDIO_R_I/O 15
16 REG_GND
C S_Y_I/O 10 S_Y_I/O LANC_SIG 17 LANC_SIG C
VIDEO_I/O 9 S_C_I/O MULTI_JACK_AD 18 JACK_AD
1314 FB7308
VIDEO/AUDIO_GND 8 VIDEO_I/O LANC_DC 19 LANC_DC
JACK_AD 7 20 REG_GND
AV OUT AUDIO_R 6 VIDEO_I/O 21 VIDEO_I/O

S_C_I/O 5 22 REG_GND
LANC_DC 4 LANC_DC S_C_I/O 23 S_C_I/O
S GND 3 MULTI_JACK_AD 24 REG_GND

1112 LANC_SIG 2 S_Y_I/O S_Y_I/O
LANC_SIG 25
AUDIO_L 1 26 REG_GND
10P FB7301
CN7302
AUDIO_R_I/O
FB7302
AUDIO_L_I/O
D D
220p
220p
C7301
C7302
VDR733
VDR734
VDR735
VDR736
VDR732
VDR731
XX
XX
XX
REG_GND
CHASSIS_GND
E LND731
E
F
JK-342 BOARD F
JACK
XX MARK:NO MOUNT
08
4-34 JK-342
• Refer to page 4-3 (English), 4-4 (Japanese) for mark 0.
1 2 3 4 5 6 7 8 9 10 11 12
D5202
T5201
CRF02
A (TE85R) A
2 6
C5204 R5204
L5201 220p 4700
2.2uH
50V 1
(TE85R)
D5201
CRF02
4
18 XE_A
C5206
LD5201
MC+
70u 17 XE_A
C5203 330V
10u 3 5 16 XE_A
B 10V CHARGING
3216 CAPACITOR 15 XE_A
14 N.C.
LD5202
GND
IC5201 13 N.C.
TPS65552DGQR
FLASH CONTROL 12 ST_GND
B CHARGE CONTROL B
11 ST_GND FLASH UNIT
NC (FL25500)
10
1
VBAT 10 N.C.
8.3 LND001-LND004,
R5203 PGND LND009, LND010,
9
9 N.C.
0 8.3 SW 0
CHG LND014-LND017,
8
VCC 8 XE_K LND023, LND024
1608 5.1 2.8
XINCHG Q5201 XE_K
HGND
PAGE 4-49
7
7
0 F_ON 0 TIG022TS-S-TL-E of LEVEL 2
R5201 G_IGBT SWITCH XE_K
6
I_PEAK 6
330k 1.9
0.5% 11 283 5 XE_K
R5202 4 N.C.
100k
0.5% 3 N.C.
ST_UNREG 14 R5205
100 2 Adapter Detect
ST_UNREG 13 C5205
XX 0 1 REG_GND(ST_GND)
ST_UNREG C5201 C5202 1608
12 B 1608 0.1u D5204
2.2u R5210 R5211
10V B B CN5201 18P
NC 11 XX XX XX
C 1608
16V
2012
10V
R5206
1M C
SCHARGE_ON 10 1005
FP-724 XSCHARGE_FULL 9
CL5201
FLEXIBLE R5209 XX
LND101-LND114 STROBO_ON 8
PAGE 4-45 NC 7
of LEVEL 2
MT_5V 6
ST_GND 5
ST_GND 4
ST_GND 3
ST_GND 2
Adapter Detect 1
14P CN5202
D D
R5207 1k
E E
F F
G G
H H
ST-175 BOARD
FLASH DRIVE
XX MARK:NO MOUNT
NO MARK:REC/PB MODE
08
4-35 ST-175
1 2 3 4 5 6 7 8
A A
B C7401
XX D7402 B
XX BH7401
(BATTERY HOLDER)
C7402 D7403
XX XX Note: BT7401 (lithium secondary battery)
is not included in the MS-374
complete board.
20P CN7401
BATT_LI_3V 1 BT7401 SH_GND_A
(LITHIUM SECONDARY BATTERY)
REG_GND 2
MS_BS 3
REG_GND 4 CN7402 10P
MS_DATA1 5 1 VSS
XX R7402
REG_GND 6 2 MSBS
FB7401 11
180 R7403 MSDATA1
MS_DATA0 7 3
FB7402
C FP-720 REG_GND 8
180 R7404
4 MSDATA0 C
FLEXIBLE MS_DATA2 9
180 R7405 FB7403
5 MSDATA2 MEMORY
LND101-LND120
PAGE 4-42
of LEVEL 2
REG_GND 10
180 R7406 FB7404
6 XMS_IN
STICK DUO
XMS_IN 11 7 MSDATA3
XX R7407
REG_GND 12 8 MS_SCLK
R7401 XX
MS_DATA3 13 9 VCC 12
C7404 C7405
C7403 0.1u VSS
REG_GND 14 XX 22u 10
6.3V B
MS_SCLK 15 TA P 10V
1005
REG_GND 16
MS_VCC 17
MS_VCC 18 SH_GND_B
1 2
ACCESS_LED_A 19
ACCESS_LED 20
D D7401
D
CL-271HR-C-TS
(ACCESS)
E E
F
MS-374 BOARD F
MS CONNECTOR
XX MARK:NO MOUNT
08
4-36 MS-374
1 2 3 4
A A
D5901 RB5901
47k
NESW007AT-T099 1 2
(EVF BACKLIGHT) 3 4
5 6
20P CN5901 R5901 7 8
R5904
LED_K 1 XX
XX
1608
EP_4.6V 2
EVF_GND 3
EVF_COM 4 21 EVF_COM
B EVF_PSIG 5 20 EVF_PSIG B
EVF_VG 6 19 EVF_VG
EVF_VR 7 18 EVF_VR
EVF_VB 8 17 EVF_VB
EVF_PCG 9 16 EVF_PCG
EVF_VCK 10 15 EVF_EN
EVF_STB 11 14 EVF_VCK
EVF_EN 12 13 EVF_VST
EVF_VST 13 12 EVF_STB
EVF_REF 14 11 EVF_REF
EVF_GND 15 10 EVF_DWN
EVF_HCK1 16 9 EVF_NRW
EVF_HCK2 17 8 EVF_RGT
C C
EVF_HST 18 7 EVF_HCK1
EVF_GND 19 6 EVF_HCK2
EVF_VDD 20 5 EVF_HST
4 VSSG
C5901 C5902 D5902
1u R5902 3 VSS
0.1u B
FP-728 B 1608
XX C5903
2
XX EVF_VDD
FLEXIBLE B
LND101-LND120 MAZS056008S0 1608 1 N.C.
PAGE 4-47 CN5902 21P
of LEVEL 2
D LCD902 D
COLOR
EVF
UNIT
E E
F
BL-013 BOARD F
:SR7/SR7E/SR8/SR8E
EVF, EVF BACKLIGHT
08
XX MARK:NO MOUNT
4-37 BL-013
08
F
E
C
B
A
D
1
Ver. 1.1 2007.06
Pin
1 LND001 NC
3
NC
3 LND003 3.3V
4 LND004 3.3V
LND005 3.3V
LND006 3.3V
LND007 3.3V
LND008 3.3V
LND009 3.3V
LND010 3.3V
LND011 DAPS-
LND012 CS1-
LND013 CS0- Pin

4
LND014 DA2 reserved LND089 40
LND015 DA0 3.3V LND088 39
LND016 DA1 3.3V LND087 38
LND017 INTRQ DASP- LND086
LND018 DMACK- CS1- LND085
LND019 GROUND CS0- LND084

LND020 GROUND DA2 LND083
LND021 IORDY DA0 LND082
LND022 GROUND NC(PDIAG-) LND081
LND023 GROUND DA1 LND080
4-38
LND024 GROUND INTRQ LND079
LND025 GROUND DMACK- LND078
LND026 DIOR- GND LND077
5
LND027 DIOW- IORDY LND076

LND028 GROUND GND LND075
PAGE 4-7
CN1004
(1/21)
LND029 GROUND DIOR- LND074
of LEVEL 3
VC-504
LND030 GROUND DIOW- LND073
LND031 DMARQ GND LND072
LND032 GROUND DMARQ LND071
LND033 GROUND GND LND070
R8401 10
DRIVE
LND034 DD15 DD15 LND069

R8402 10
HARD DISK

R8403 10
R8404 10
R8405 10
R8406 10
6

R8407 10
R8408 10
R8409 10
R8410 10
R8411 10
R8412 10
R8413 10
R8414 10
R8415 10
R8416 10
49 LND049 DD7 DD7 LND054 5
50 LND050 GROUND GND LND053 4
51 LND051 -RESET RESET- LND052 3

7
reserved
reserved
HDD CONNECTION
8

F
E
A
C
B
FP-515
1 2 3 4 1 2 3 4
A A A A
LND001 PANEL_B 24 24 PANEL_B LND324
LND002 PANEL_G 23 23 PANEL_G LND323
LND003 PANEL_R 22 22 PANEL_R LND322
LND004 REG_GND 21 21 REG_GND LND321
LND006 PANEL_HD 19 19 PANEL_HD LND319
LND007 2nd S/S 18 18 KEY_AD LND318 6 PANEL_REV LND006
LND008 EP_4.6V 17 17 EP_4.6V LND317 S001 5 PANEL_REV LND005

3 2
B B B PANEL 4 N.C. LND004
CK-183 B
LND009 D_2.8V 16 16 D_2.8V LND316 CN6001
REVERSE
LND010 PANEL_VD 15 15 PANEL_VD LND315 DETECT 3 N.C. LND003 PAGE 4-32
LND002
of LEVEL 2
LND011 14 14 BL_CONT LND314 4 1 2 REG_GND
CK-183 BL_CONT PD-324
CN6004 LND012 REG_GND 13 13 REG_GND LND313 CN6101 1 REG_GND LND001
PAGE 4-32 PAGE 4-33
of LEVEL 2 of LEVEL 2
LND014 BB_SI 11 11 BB_SI LND311
LND015 BB_SO 10 10 BB_SO LND310

LND016 XCS_LCD 9 9 XCS_LCD LND309
LND017 XBB_SCK 8 8 XBB_SCK LND308

LND019 TP _ Y 6 6 TP _ Y LND306
LND020 TP _ SEL1 5 5 TP _ SEL1 LND305
TP_X 4 TP_X
C LND021 4 LND304
C C C
LND022 BL_-V 3 3 BL_-V LND303
LND023 EP_2.8V 2 2 EP_2.8V LND302
LND024 EP_8.5V 1 1 EP_8.5V LND301
D D D D
E E E E
F FP-537 FLEXIBLE BOARD F F F

CK-PD CONNECTION FP-546 FLEXIBLE BOARD
(PRINTED WIRING BOARD is omitted.) PANEL REVERSE DETECTION SWITCH
08 08
4-39 FP-537, FP-546
1 2 3 4 1 2 3 4
A A A CONTROL SWITCH A
BLOCK
(AD11800)
1Pin-6Pin
PAGE 4-48
of LEVEL 2
6P CN7171
DIAL_B 1
DIAL_B 2
REG_GND 3
REG_GND 4 Pin
DIAL_A 5 DIAL_B LND001 1
B B B DIAL_A 6 REG_GND LND002 2 LD-228 B
DIAL_A LND003 3 (1/4)
CN5306
REG_GND LND004 4
PAGE 4-28
S7171 of LEVEL 3
PON SW LND005 5
MANUAL
Pin Pin REG_GND LND006 6
2 1
1 LND101 CHASSIS_GND CHASSIS_GND LND010 10
2 LND102 LENS_COVER_LED_ON LENS_COVER_LED_ON LND009 9

4 3
3 LENS_COVER_OPEN LENS_COVER_OPEN 8
LND103 LND008
REG_GND REG_GND
LD-228 LND104 LND007
(1/4) LND105 LENS_COVER_LED_ON LENS_COVER_LED_ON LND006 LENS
CN5305 BARRIER
LND106 LENS_COVER_CLOSE LENS_COVER_CLOSE LND005
PAGE 4-28
of LEVEL 3 SHUTTER_XB SHUTTER_XB
LND107 LND004
8 3
C LND108 SHUTTER_A SHUTTER_A LND003 C C C
9 LND109 SHUTTER_B SHUTTER_B LND002 2
10 LND110 SHUTTER_XA SHUTTER_XA LND001 1
D D D D
E E E E
F FP-712 FLEXIBLE BOARD F F FP-717 FLEXIBLE BOARD F
LENS BARRIER MANUAL CONTROL SWITCH

08
(PRINTED WIRING BOARD is omitted.)
08
:SR7/SR7E/SR8/SR8E
4-40 FP-712, FP-717
1 2 3 4 5 6 7 8
A Note : CN7181 is not supplied, but this is included in

A
the FP-718 flexible complete board.
CHASSIS_GND
LND052
Pin
1 LND001 D_DET
2 LND002 D_CTRL1
3 LND003 D_CTRL2
LND004 D_CTRL3
LND005 LANC_SIG
B LND006 LANC_DC B
LND007 BATT/XEXT
KEY_AD3
LND008 (DVD BURN)
LND009
LND010 ACV_GND
LND011 ACV_GND
LND012 ACV_GND
LND013 ACV_GND
LND014 ACV_GND
LND015 ACV_GND
LND016 ACV_GND
LND017 ACV_GND 42 ACV_GND ACV_GND 41

ACV_GND 40 ACV_GND ACV_GND 39
C LND018
C
LND019 USB_GND 38 USB_GND PON(DVD BURN) 37
LND020 USB_D- 36 USB_D- BATT/XEXT_CR 35
LND021 34 USB_D+ LANC_DC 33
LND022 USB_D+ 32 USB_GND LANC_SIG 31
LND023 USB_GND 30 USB_DET/VBUS N.C 29

USB_VBUS (USB_ID) N.C
VC-504 LND024 28 27
(1/21) LND025 MULTI_JACK_IN 26 MULTI_JACK_IN CTRL3 25
CN1013 REG_GND
LND026 REG_GND 24 CTRL2 23
PAGE 4-7
of LEVEL 3 AUDIO_R_I/O 22 AUDIO_R CTRL1 21
LND027
LND028 AUDIO_L_I/O 20 AUDIO_L DET 19
LND029 REG_GND 18 REG_GND Pr 17
LND030 S_Y_I/O 16 S_Y_I/O REG_GND 15

D LND031 REG_GND 14 REG_GND Pb 13 D
LND032 S_C_I/O 12 S_C_I/O REG_GND 11
LND033 REG_GND 10 REG_GND Y 9
LND034 VIDEO_I/O 8 VIDEO_I/O REG_GND 7
LND035 6 N.C N.C 5
LND036 ACV_UNREG 4 ACV_UNREG ACV_UNREG 3
LND037 ACV_UNREG 2 ACV_UNREG ACV_UNREG 1
LND038 ACV_UNREG 42P CN7181
LND039 ACV_UNREG
TO CRADLE
LND040 ACV_UNREG (Handycam Station)
LND041 ACV_UNREG
LND042 ACV_UNREG
ACV_UNREG
E LND043
E
LND044 ACV_UNREG
LND045
LND046 REG_GND
LND047 D_Y
LND048 REG_GND
49 LND049 D_PB
50 LND050 REG_GND
51 LND051 D_PR
F F
CRADLE TERMINAL
08
4-41 FP-718
1 2 3 4 1 2 3 4
Pin Note : BH720 is not included in the FP-720 flexible board.

Note : CN7191 is not supplied, but this is included in 1 LND001 BATT_UNREG
the FP-719 flexible complete board. 2 LND002 BATT_UNREG
3 LND003 BATT_UNREG
A Pin A A LND004 BATT_UNREG A
LND026 GND
24 LND024 GND LND005 BATT_UNREG 1
23 LND023 GND LND006 BATT_UNREG
BH720
22 LND022 TMDS DATA2 + CN7191 19P HDMI LND007 BATT_SIG 2
C BATTERY
LND021 TMDS DATA2 - 1 TMDS_DATA2_SHIELD LND008 BATT_GND TERMINAL
4
LND020 GND 2 TMDS_DATA2_+ LND009 BATT_GND
LND019 GND 3 TMDS_DATA2_- LND010 BATT_GND
LND018 TMDS DATA1 + 4 TMDS_DATA1_SHIELD LND011 BATT_GND SH_GND LND991
LND017 TMDS DATA1 - 5 TMDS_DATA1_+ LND012 BATT_GND Pin
LND016 GND 6 TMDS_DATA1_- LND013 BATT_GND ACCESS_LED LND120 20

VC-504
GND LND014 XMS_ACCESS_LED ACCESS_LED_A LND119 19
LND015 7 TMDS_DATA0_SHIELD (1/21)
B VC-504 LND014 TMDS DATA0 + 8 TMDS_DATA0_+ B B CN1017 LND015 ACCESS_LED_A MS_VCC LND118 18 B
PAGE 4-7
(1/21) LND013 TMDS DATA0 - 9 TMDS_DATA0_- of LEVEL 3 LND016 MS_VCC MS_VCC LND117
CN1021
LND012 GND 10 TMDS_CLOCK_SHIELD LND017 REG_GND REG_GND LND116
PAGE 4-7
of LEVEL 3 GND LND018 MS_SCLK MS_SCLK LND115
LND011 11 TMDS_CLOCK_+
LND010 TMDS CLOCK + 12 TMDS_CLOCK_- LND019 REG_GND REG_GND LND114
LND009 TMDS CLOCK - 13 DDC_CEC_GND LND020 MS_DATA3 MS_DATA3 LND113

LND008 GND 14 CEC LND021 REG_GND REG_GND LND112
LND007 GND 15 SCL LND022 XMS_IN LND111

MS-374
XMS_IN CN7401
LND006 SCL 16 SDA LND023 REG_GND REG_GND LND110 PAGE 4-36
of LEVEL 2
LND005 SDA 17 RESERVED LND024 MS_DATA2 MS_DATA2 LND109
LND004 +5V POWER 18 +5V_POWER LND025 REG_GND REG_GND LND108
3 LND003 +5V POWER 19 HPD LND026 MS_DATA0 MS_DATA0 LND107
2 HPD LND027 LND106

C LND002 C C REG_GND REG_GND C
1 LND001 GND LND028 MS_DATA1 MS_DATA1 LND105
LND029 REG_GND REG_GND LND104
LND025 GND
30 LND030 MS_BS MS_BS LND103 3
31 LND031 REG_GND REG_GND LND102 2

32 LND032 BATT_LI_3V BATT_LI_3V LND101 1
D D D D
E E E E
F F F FP-720 FLEXIBLE BOARD F
FP-719 FLEXIBLE BOARD BATTERY TERMINAL

HDMI CONNECTOR (PRINTED WIRING BOARD is omitted.)
08 08
4-42 FP-719, FP-720
1 2 3 4 1 2 3 4
Note : J7211 and J7212 are not included in Note : J7221 and J7222 are not included in
the FP-721 flexible board. the FP-722 flexible board.
Pin
A A A Pin A
20 LND020 LANC_DC J7211
HP_GND LND012 12
19 LND019 LANC_JACK_IN REMOTE
232C_TD 4
HP_JACK_IN LND011 11
LND018 LANC_SIG SIG 1
18 JACK_IN 5
LANC_DC 2 1 GND HP_GND LND010 10
LND017 REG_GND J7221
GND 3 2 L HP_L_OUT LND009
LND016 N.C 3 S
(headphone) HP_GND LND008
ACV_GND 4 R
LND015
HP_R_OUT
VC-504
LND007
LND014 ACV_GND (1/21)
HP_GND LND006 CN1022
LND013 ACV_GND
GND MIC_GND LND005 PAGE 4-7
ACV_GND 1 of LEVEL 3
VC-504 LND012 J7222 2 L
EXT_MIC_R LND004
(1/21) ACV_GND 3 S
LND011 MIC
CN1009 COLD 1 (PLUG IN POWER) 4 MIC_GND LND003 3
LND010 ACV_GND R
B PAGE 4-7 SW 3
2
B B EXT_MIC_L LND002 2 B
of LEVEL 3 LND009 N.C
HOT J7212 MIC_GND LND001 1
LND008 ACV_UNREG DC IN
LND007 ACV_UNREG
LND006 ACV_UNREG
LND005 ACV_UNREG
LND004 ACV_UNREG
3 LND003 ACV_UNREG
2 LND002 N.C
1 LND001 BATT/XEXT
C C C C
D D D D
E E E E
F FP-721 FLEXIBLE BOARD F F

FP-722 FLEXIBLE BOARD F
:SR7/SR7E/SR8/SR8E
REMOTE, DC IN HP, MIC JACK
08 08 (PRINTED WIRING BOARD is omitted.)
4-43 FP-721, FP-722
1 2 3 4 5 6 7 8
Pin Pin
1 LND001 A_3.3V/A_2.8V A_3.3V/A_2.8V LND145 45
2 LND002 D_1.5V D_1.5V LND144 44

A A
3 LND003 D_2.8V D_2.8V LND143 43
LND004 MT_5V MT_5V LND142
LND005 MT_5V MT_5V LND141
LND006 MT_GND MT_GND LND140
LND007 MT_GND MT_GND LND139
LND011 PNDCK(13.5MHz) PNDCK LND135
LND013 IC2701_SYSCLK IC2701_SYSCLK LND133

B B
LND017 CAM_SI CAM_SI LND129
LND018 XCAM_SCK XCAM_SCK LND128
LND019 DIRA1 DIRA1 LND127
LND020 CAM_SO CAM_SO LND126

LD-228 LND021 DIRB1 LND125
(1/4)
DIRB1 VC-504
CN5303 LND022 DIRA0 DIRA0 LND124 (1/21)
EN0 CN1012
PAGE 4-28 LND023 EN0 LND123
of LEVEL 3 PAGE 4-7
LND024 DIRB0 DIRB0 LND122 of LEVEL 3
LND025 CAM_VD CAM_VD LND121

C LND026 EN1 EN1 LND120 C
LND027 LENS_COVER_OPEN LENS_COVER_OPEN LND119
LND028 IR_NOISE IR_NOISE LND118
LND029 LENS_COVER_LED_ON LENS_COVER_LED_ON LND117
LND030 LENS_COVER_CLOSE LENS_COVER_CLOSE LND116
LND031 ND_NOISE ND_NOISE LND115
LND032 LENS_TEMP_AD LENS_TEMP_AD LND114
LND033 NF_SW NF_SW LND113
LND034 NF_EN NF_EN LND112
LND035 THERM THERM LND111
LND036 XCS_IC5404 XCS_IC5404 LND110
LND037 XDS_RESET XDS_RESET LND109
LND038 XRST_IC5404 XRST_IC5404 LND108

D D
LND039 XRST_IC5703_CPU XRST_IC5703_CPU LND107
LND040 YAW_AD YAW_AD LND106
LND041 PITCH_AD PITCH_AD LND105
LND042 VST_C_RESET VST_C_RESET LND104

43 LND043 XPON_SW XPON_SW LND103 3
44 LND044 DIAL_A DIAL_A LND102 2

45 LND045 DIAL_B DIAL_B LND101 1
E E
F
FP-723 FLEXIBLE BOARD F
LD-VC CONNECTION
08
4-44 FP-723
1 2 3 4 1 2 3 4
A A A A
Pin Pin
Pin
1 LND001 ST_UNREG ST_UNREG LND114 14
16 GND
Pin
REG_GND(SHOE_GND) 1
LND004 NC NC LND111
13 SHOE_CONT SHOE_CONT 2
LND005 SCHARGE_ON SCHARGE_ON LND110
LANC LANC_SIG 3
LND006 XSCHARGE_FULL XSCHARGE_FULL LND109
B VC-504 B B Active STROBE EXT_STROBE B
(1/21) LND007 STROBO_ON STROBO_ON LND108 ST-175 Interface Shoe
CN1010 CN5202 ID2 HOTSHOE_ID2
LND008 NC NC LND107 VC-504
PAGE 4-7 PAGE 4-35 UNREG SHOE_UNREG
of LEVEL 3 LND009 MT_5V MT_5V LND106 of LEVEL 2 HOT (1/21)
SHOE
UNREG SHOE_UNREG CN1019
LND010 ST_GND ST_GND LND105
ID1 HOTSHOE_ID1 PAGE 4-7
LND011 ST_GND ST_GND LND104 of LEVEL 3
MIC_RL MIC_RL
12 LND012 ST_GND ST_GND LND103 3
MIC_RR MIC_RR
13 LND013 ST_GND ST_GND LND102 2
MIC_GND SHOE_MIC_GND
14 LND014 Adapter Detect Adapter Detect LND101 1
3 MIC_FL MIC_FL 12
2 MIC_FR MIC_FR 13
1 GND REG_GND 14
C C C C
D D D D
E E E E
F
FP-724 FLEXIBLE BOARD F F FP-725 FLEXIBLE BOARD F
VC-ST CONNECTION HOT SHOE CONNECTION

08
(PRINTED WIRING BOARD is omitted.) 08
4-45 FP-724, FP-725
1 2 3 4 1 2 3 4
A A A A
Pin Pin
1 LND001 REG_GND REG_GND LND126 26 Pin Pin
2 LND002 S_Y_I/O S_Y_I/O LND125 25 1 LND001 SP+ SP+ LND101 30

3 LND003 REG_GND REG_GND LND124 24 2 LND002 SP- SP- LND102 29
LND004 S_C_I/O S_C_I/O LND123 3 LND003 PANEL_NOR/REV PANEL_NOR/REV LND103 28
LND005 REG_GND REG_GND LND122 LND004 XBATT_VIEW XBATT_VIEW LND104
LND006 VIDEO_I/O VIDEO_I/O LND121 LND005 KEY_AD2 KEY_AD2 LND105

LND007 REG_GND REG_GND LND120 LND006 RESET RESET LND106
B LND008 LANC_DC LANC_DC LND119 B B LND007 EP_8.5V EP_8.5V LND107 B
LND009 JACK_AD JACK_AD LND118 LND008 EP_2.8V LND108
EP_2.8V
LND010 LANC_SIG LANC_SIG LND117 LND009 BL_-V BL_-V LND109
LND011 REG_GND REG_GND LND116 LND010 TP_X TP_X LND110
LND012 AUDIO_R_I/O AUDIO_R_I/O LND115 LND011 TP_SEL_1 LND111
VC-504 JK-342 TP_SEL_1
(1/21) LND013 REG_GND REG_GND LND114 CN7303 LND012 TP_Y TP_Y LND112
CN1026
LND014 AUDIO_L_I/O AUDIO_L_I/O LND113 PAGE 4-34 LND013 REG_GND LND113
PAGE 4-7 of LEVEL 2 REG_GND
of LEVEL 3 LND015 REG_GND REG_GND LND112
VC-504 LND014 XBB_SCK LND114
XBB_SCK
(1/21) CK-183
LND016 D3_CN XD3_CN LND111 CN1006 LND015 XCS_LCD XCS_LCD LND115 CN6005
LND017 LND110 PAGE 4-7 LND016 BB_SO LND116 PAGE 4-32
LIN_CNT3 LIN_CNT3 of LEVEL 3 BB_SO of LEVEL 2
LND018 LIN_CNT2 LIN_CNT2 LND109 LND017 BB_SI BB_SI LND117
LND019 LIN_CNT1 LIN_CNT1 LND108 LND018 REG_GND REG_GND LND118

LND020 REG_GND REG_GND LND107 LND019 BL_CONT BL_CONT LND119
C C C C
LND021 D3_LNO_PR D3_LNO_PR LND106 LND020 PANEL_VD PANEL_VD LND120
LND022 REG_GND REG_GND LND105 LND021 D_2.8V D_2.8V LND121
LND023 D3_LNO_PB D3_LNO_PB LND104 LND022 EP_4.6V LND122

EP_4.6V
24 LND024 REG_GND REG_GND LND103 3 LND023 (2nd S/S,Zoom,HOME) (2nd S/S,Zoom) LND123
25 LND025 D3_LNO_Y D3_LNO_Y LND102 2 LND024 PANEL_HD PANEL_HD LND124
26 LND026 REG_GND REG_GND LND101 1 LND025 REG_GND LND125

REG_GND
LND026 PANEL_R PANEL_R LND126
LND027 PANEL_G PANEL_G LND127
28 LND028 PANEL_B PANEL_B LND128 3
29 LND029 REG_GND REG_GND LND129 2
30 LND030 PANEL_OPEN/CLOSE PANEL_OPEN/CLOSE LND130 1
D D D D
E E E E
F
FP-726 FLEXIBLE BOARD F F FP-727 FLEXIBLE BOARD F
VC-JK CONNECTION VC-CK CONNECTION

(PRINTED WIRING BOARD is omitted.) (PRINTED WIRING BOARD is omitted.)
08 08
4-46 FP-726, FP-727
1 2 3 4 1 2 3 4
A A A A
Pin Pin Pin
1 LND001 EVF_VDD EVF_VDD LND120 20 SIRCS_SIG LND008 8
D_2.8V
2 LND002 EVF_GND EVF_GND LND119 19 SIRCS_VDD LND007 7
3 LND003 EVF_HST EVF_HST LND118 18 REG_GND LND006 6 VC-504

LND004 EVF_HCK2 EVF_HCK2 LND117 TALLY_LED_K LND005 (1/21)
2.8 CN1025
OUT
VCC
SIRCS_SIG TALLY_LED_A
LND005 EVF_HCK1 LND116 LND004
4
EVF_HCK1 IC7291 PAGE 4-7
2.8
LND006 EVF_GND LND115 RS-770 REG_GND LND003 3 of LEVEL 3
EVF_GND
REMOTE SENSOR
GND
GND
LND007 EVF_REF EVF_REF LND114 LND002 2
3
C7291 NS_LED_K
LND008 EVF_VST LND113 1u NS_LED_A 1
VC-504 EVF_VST B LND001
(17/21) LND009 EVF_EN EVF_EN LND112 BL-013
B CN3701 CN5901 B B B
LND010 EVF_STB EVF_STB LND111
PAGE 4-23 PAGE 4-37
of LEVEL 3 LND011 EVF_VCK EVF_VCK LND110 of LEVEL 2
LND012 EVF_PCG EVF_PCG LND109

LND013 EVF_VB EVF_VB LND108
LND014 EVF_VR EVF_VR LND107
LND015 EVF_VG EVF_VG LND106 D7292

SML-310LTT86
LND016 EVF_PSIG EVF_PSIG LND105 (TALLY)
LND017 EVF_COM EVF_COM LND104
18 LND018 EVF_GND EVF_GND LND103 3

SE_GND
19 LND019 EP_4.6V EP_4.6V LND102 2
20 LND020 LED_K LED_K LND101 1
C C C C
D7291
CL-330IRS-X-TU
(NIGHT SHOT)
D D D D
E E E E
F
FP-728 FLEXIBLE BOARD F F F
:SR7/SR7E/SR8/SR8E
BL-VC CONNECTION
08
(PRINTED WIRING BOARD is omitted.) 08
REMOTE SENSOR
4-47 FP-728, FP-729
1 2 3 4 1 2 3 4
A A A A
CHASSIS_GND
1 2 3 4
7 5
8 6
S001
Dial_B NIGHT SHOT
S002
REG_GND
B B B B
20pin
REG_GND
S001
Dial_A N.S SW
CAMERA
CONTROL D002
CHARGE_LED_VDD
(CHARGE/STROBE)
XCHARGE_LED 3 1 RV001
REG_GND W (ZOOM) T
2
D004
XCAM_LED
(CAM)
MODE_LED_VDD
D003
Pin XPHOTO_LED
(PHOTO)
DIAL_B 1 XACCESS_LED
D001
DIAL_B 2 FP-717 ACCESS_LED_VDD
(ACCESS)
FLEXIBLE 2 1
REG_GND 3 ZOOM_VR_AD S004
CN7171
C REG_GND 4 C C D_2.8V PHOTO C
PAGE 4-40
of LEVEL 2 4 3 (PHOTO REC)
DIAL_A 5 REG_GND 2 1
S003
DIAL_A 6 PHOTO_REC
(PHOTO FREEZE)
PHOTO_FREEZE 4 3
2 1 S002
XPOWER_SW
XMODE_SW ( /CHG
)
4 3
S/S
XSTROBE_SW
OFF
(CHG)
REG_GND
CHASSIS_GND
1pin
XMODE_SW ON POWER
VC-504
(1/21) XPOWER_SW
CN1003 MODE
D D D 2 1
D
PAGE 4-7
of LEVEL 3
4 3
S006
START/STOP
E E E E
CONTROL SWITCH BLOCK

(AD11800) CONTROL SWITCH BLOCK
F :SR7/SR7E/SR8/SR8E F F
(PS25500) F
08
( CONTROL SWITCH BLOCK (AD11800) is replaced as block,
so that PRINTED WIRING BOARD is omitted. ) 08
( CONTROL SWITCH BLOCK (PS25500) is replaced as block,
so that PRINTED WIRING BOARD is omitted. )
4-48 AD11800, PS25500
Ver. 1.1 2007.06
1 2 3 4 1 2 3 4
A A
A A
S7491
BACKLIGHT S001
OFF (ADAPTER DETECT)
1 2 Pin
REG_GND LND001 1
ON
REG_GND LND002 2 ST_GND 1PIN
3 4 CK-183 1 2 LND023
LND003 3 CN6002 adapter detect 2PIN
3 4 LND024
LND004 4 PAGE 4-32 3PIN
of LEVEL 2 N.C.
B BACK_LIGHT LND005 5 B N.C. 4PIN
XE-K
BACK_LIGHT LND006 6 B LND001 5PIN B
LND050 XE-K LND002 6PIN
XE_K XE-K LND003 7PIN
LND052 XE-K LND004 8PIN
COMMON
N.C. 9PIN
ST-175
C001 CN5201
0.033u N.C. 10PIN PAGE 4-35
LND053 B of LEVEL 2
250V ST_GND LND009 11PIN
FLASH TRIGEER ST_GND LND010 12PIN

UNIT R001 N.C. 13PIN
3216
1M
CONTROL SWITCH BLOCK 1/8W N.C.

XE-A LND014
14PIN
15PIN
C C XE-A LND015 16PIN
(SB25500) C
XE_A
LND051
XE-A
XE-A
LND016
LND017
17PIN
18PIN
C
( CONTROL SWITCH BLOCK (SB25500) is replaced as block,

08
1 2 3 4
A A D D
S001
STARAT/STOP
6 REG_GND
S002
5 2ndS/S
W PD-324
4 2ndZOOM_W CN6104
(ZOOM) 3 2ndZOOM_T Page 4-33
S003 of LEVEL 2
B 2 HOME B
T
1 REG_GND
S004
E E
HOME
CONTROL KEY BLOCK

C
(SB22200) C
CONTROL KEY BLOCK (SB22200) is replaced as block,

F
FLASH UNIT(FL25500) F
so that PRINTED WIRING BOARD is omitted.
08 08
( FLASH UNIT (FL25500) is replaced as block,
4-49 SB25500, SB22200, FL25500
Signal location of the VC-504 and LD-228 boards are not shown.
4-3. SIGNAL LOCATION

CK-183 BOARD PD-324 BOARD
BB_SI (1/1) C-6 BB_SI (1/1) B-3 PANEL_VR (1/1) C-8
(1/1) C-7 (1/1) C-4 (1/1) C-10
BB_SO (1/1) C-6 BB_SO (1/1) B-3 PANEL_VST (1/1) B-10
(1/1) C-7 (1/1) C-4 (1/1) C-7
BL_CONT (1/1) C-6 BIN (1/1) A-3 PANEL_XHD (1/1) A-3
(1/1) C-7 (1/1) B-5 (1/1) C-5
BL_-V (1/1) B-6 BL_CONT (1/1) B-3 PANEL_XSTBY (1/1) B-8
(1/1) B-7 (1/1) G-5 (1/1) B-10
D_2.8V (1/1) C-6 BL_L (1/1) F-10 (1/1) D-7
(1/1) C-7 (1/1) H-7 PANEL_XVD (1/1) B-3
EP_2.8V (1/1) B-6 BL_ON (1/1) C-7 (1/1) D-5
(1/1) B-7 (1/1) E-5 RIN (1/1) A-3
EP_4.6V (1/1) C-6 (1/1) G-5 (1/1) B-5
(1/1) C-7 BL_-V (1/1) C-3 TP_SEL1 (1/1) B-3
EP_8.5V (1/1) B-6 (1/1) E-5 (1/1) F-4
(1/1) B-7 (1/1) H-5 TP_X (1/1) C-3
HI_XRESET (1/1) B-4 D_2.8V (1/1) B-3 (1/1) E-4
(1/1) B-7 (1/1) F-4 TP_Y (1/1) B-3
KEY_AD0 (1/1) C-6 EP_2.8V (1/1) A-4 (1/1) F-4
(1/1) C-7 (1/1) C-3 XBB_SCK (1/1) B-3
KEY_AD2 (1/1) B-7 (1/1) G-5 (1/1) C-4
(1/1) D-4 EP_4.6V (1/1) A-3 XCS_LCD (1/1) B-3
PANEL_B (1/1) D-6 (1/1) A-4 (1/1) C-4
(1/1) D-7 (1/1) E-5
PANEL_G (1/1) D-6 EP_8.5V (1/1) A-4
(1/1) D-7 (1/1) C-3
PANEL_HD (1/1) C-6 (1/1) F-5
(1/1) C-7 EXTDA (1/1) B-5
PANEL_NOR/REV (1/1) B-3 (1/1) F-5
(1/1) B-7 (1/1) G-5
PANEL_O/C (1/1) A-4 GIN (1/1) A-3
(1/1) D-7 (1/1) B-5
PANEL_R (1/1) D-6 KEY_AD (1/1) A-3
(1/1) D-7 (1/1) D-4
PANEL_VD (1/1) C-6 LED_1A (1/1) D-10
(1/1) C-7 (1/1) F-9
SP- (1/1) B-7 LED_2A (1/1) E-10
(1/1) C-4 (1/1) F-8
SP+ (1/1) B-7 LED_3A (1/1) E-10
(1/1) C-4 (1/1) F-9
TP_SEL_1 (1/1) B-6 PANEL_COM (1/1) B-7
(1/1) B-7 (1/1) B-10
TP_X (1/1) B-6 (1/1) C-10
(1/1) B-7 PANEL_DWN (1/1) B-10
TP_Y (1/1) B-6 (1/1) D-7
(1/1) B-7 PANEL_EN (1/1) B-10
XBATT_VIEW (1/1) B-7 (1/1) D-7
(1/1) E-4 PANEL_HCK1 (1/1) C-10
XBB_SCK (1/1) B-6 (1/1) D-7
(1/1) C-7 PANEL_HCK2 (1/1) C-10
XCS_LCD (1/1) C-6 (1/1) D-7
(1/1) C-7 PANEL_HST (1/1) C-10
(1/1) D-7
PANEL_PCG (1/1) B-10
(1/1) D-7
PANEL_REF (1/1) B-7
(1/1) C-10
PANEL_RGT (1/1) C-10
(1/1) E-7
PANEL_VB (1/1) C-8
(1/1) C-10
PANEL_VCK (1/1) B-10
(1/1) C-7
PANEL_VG (1/1) C-8
(1/1) C-10
PANEL_VP (1/1) C-7
(1/1) C-10
4-60 CK-183, PD-324
JK-342 BOARD
AUDIO_L_I/O (1/1) C-7
(1/1) D-5
AUDIO_R_I/O (1/1) C-7
(1/1) D-5
D3_LNO_PB (1/1) B-5
(1/1) B-7
D3_LNO_PR (1/1) A-5
(1/1) B-7
D3_LNO_Y (1/1) B-5
(1/1) B-7
LANC_DC (1/1) C-7
(1/1) D-5
LANC_SIG (1/1) C-7
(1/1) D-5
LINE_CNT1 (1/1) A-5
(1/1) B-7
LINE_CNT2 (1/1) A-5
(1/1) B-7
LINE_CNT3 (1/1) A-5
(1/1) B-7
MULTI_JACK_AD (1/1) C-7
(1/1) D-5
S_C_I/O (1/1) C-5
(1/1) D-7
S_Y_I/O (1/1) C-5
(1/1) D-7
VIDEO_I/O (1/1) C-5
(1/1) C-7
XD3_CN (1/1) A-5
(1/1) C-7
4-61 JK-342
4-4. PRINTED WIRING BOARDS
Link
CK-183 BOARD FP-515 FLEXIBLE BOARD
PD-324 BOARD FP-546 FLEXIBLE BOARD

JK-342 BOARD
: SR7/SR7E/SR8/SR8E
ST-175 BOARD FP-718 FLEXIBLE BOARD
MS-374 BOARD FP-719 FLEXIBLE BOARD
BL-013 BOARD : SR7/SR7E/SR8/SR8E FP-729 FLEXIBLE BOARD
COMMON NOTE FOR PRINTED WIRING BOARDS

(ENGLISH)
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS
• : Uses unleaded solder. • Chip parts.
• : Circuit board Transistor Diode
: Flexible board C 6 5 4 4 5 6 5 4 4 5 3 3 3 1 23
Pattern from the side which enables seeing.
: pattern of the rear side
B E 1 2 3 3 2 1 1 2 3 3 2 1 2 1 2 1 2 1 6 54
(The other layers’ patterns are not indicated)
1 2 2 1 3 2 4 3 3 4 6 5 4 4 5 6
• Through hole is omitted.
• There are a few cases that the part printed on diagram
isn’t mounted in this model. 5 4 3 3 4 5 4 1 1 2 2 1 1 2 3 3 2 1
• C: panel designation 3 2
(JAPANESE) 4 1
プリント図共通ノート
【プリント図ノート】
・：無鉛半田を使用しています。
・：基板
：フレキシブル配線板
見ている面側のパターン。
：裏側のパターン
（他のパターンについては表示されていません）
・スルーホールは省略。
・プリント図には，本機で使用していない部品が記載されている
場合があります。
・Cはパネル表示名称。
4-62
Printed wiring boards of the CM-076, CM-077, VC-504 and LD-228 board are not shown.
CK-183 (2 layers)
: Uses unleaded solder.
CK-183 BOARD (SIDE A) CK-183 BOARD (SIDE B)

3 4
S6004
LND603
1 2
3 4
D6004
S6002
CN6003
2
1
D6003
1 2
EASY
3 4
D6007
S6006
LND601
R6002
R6001
1 2
R6003
(FILM ROLL INDEX)
3 4
S6003
1 2
DISP/
BATT INFO
D6006
RESET
S6001
D6001
1
CN6001
D6002
6
30
1
CN6005
CN6004
24
1
LND602
1 6
D6008
CN6002
D6005
3
S6005
PANEL
( OPEN/CLOSE )
1
08 1-872-818- 11 08 1-872-818- 11
4-68 CK-183
PD-324 (2 layers)
PD-324 BOARD (SIDE A)
LD6101
Q6113
Q6112
Q6107
C6106
R6106
R6142
R6140
R6143
R6132
1
6
4
3
1 24 C6104 E
C
B
R6139
R6141
3
4
6
1
CN6101 R6130
R6151
R6144 6 4
R6107
8 5 R6155 1 3
L6101 C6127
C6105
Q6110
R6120
R6119
Q6104 Q6105 Q6106

R6108
B
IC6101
R6110
R6150
R6109 C6108 R6129
R6111
C6110
C
C6107
Q6103
R6134
R6136
E
R6112
4
3
FB6101
C6109 R6154 R6149
B
1 4
6
1
R6138
C
C6103
R6127
R6152
E
R6118
R6116
R6146
48
37
B
R6115
R6117
R6124
36
1
R6148
R6153
R6147
E
C6118
C6115
Q6108
R6114
R6113
IC6102
C6114
C R6123
B E
C6113
C6117
C6116
R6121
C6122
R6131
C6119
L6103
D6102
12
25
6 4
13
24
D6104
Q6109 C6120
R6133
R6135
R6122
1 3
LD6102
C6124
R6125
C6121
C6111
R6126
L6102
R6128
C6112
LD6105
Q6111
R6103
E
Q6101
C6123
C
6
R6137
B
Q6102
R6104
R6102
D6101
R6145
4
R6101 R6105
1
C6125
1
1 6 CN6103
C6126
C6101 C6102
D6105 D6103 CN6104 6 1
1 24 1 6
1-871-779- 11
CN6105 CN6102
08
PD-324 BOARD (SIDE B)
(LCD BACK LIGHT)

D6106
K
A
(LCD BACK LIGHT)
D6107
K
A
(LCD BACK LIGHT)
D6108
K
A
1-871-779- 11
08
4-69 PD-324
JK-342 (2 layers), ST-175 (2 layers), MS-374 (2 layers)
JK-342 BOARD (SIDE A) JK-342 BOARD (SIDE B) ST-175 BOARD (SIDE A) ST-175 BOARD (SIDE B)
C5205
FB7307 R5201
1
3 2 1
R5207
C5202
2
FB7306 A
5
D7301 R5203 R5202 C5201
D5204
1 5 3
IC5201
FB7305
11
R5210
D5201
4 5
R5211
R5209
10
11
12
CN5202
3 2 1
R7304
CL5201
D7302 K
R5204
8
T5201
R5206
R7303 R5205
Q5201
4 5 6
C5204
CN7301
R7302 COMPONENT
CN7303
13
5
OUT
14
R7301
VDR731 6 2 4
10
VDR732 1 18
13
14
C5206 A
(CHARGING CAPACITOR)
CN5201
L5201
D5202
C5203
VDR733
C7302
C7301
K
26
FB7301
FB7302
FB7308
VDR734
11
12
LD5201
LD5202
VDR736
26 1
VDR735
11 11
4 8 3 7
1-873-191- 1-873-191-
CN7302
AV OUT
08 08
LND731
10 5 9
13
14
1-872-821- 11 1-872-821- 11
08 08
MS-374 BOARD (SIDE A) MS-374 BOARD (SIDE B)
10 1
FB7401
FB7402
FB7403
FB7404
C7405
R7402
R7403
R7405
R7406
R7407
R7404
+
P
C7404
R7401
C7403 +
P
CN7402
1 19
CN7401
C7402 C7401 2 20
Note: Replace the battery holder (BH7401) together when replacing
D7403
D7402
the lithium battery (BT7401) on MS-374 board.

(The battery holder removed once cannot be used again.)
When mounting these parts, mount new battery holder first and
attach new lithium battery next.
BH7401
Note: MS-374基板のリチウム電池(BT7401)を交換する場合はバッテリホ
12 ルダ(BH7401)も同時に新品に交換して下さい。
11 (一度使用したバッテリホルダは再使用できません。)
A
(ACCESS)
K
部品取り付けの際は、先にバッテリホルダを取り付けてから
リチウム電池を装着してください。
D7401
08
1-872-820- 11
BT7401
1-872-820- 11
MEMORY
08 LITHIUM SECONDARY CAUTION

STICK
DUO
BATTERY Danger of explosion if battery is incorrectly replaced.

Note: BT7401 (lithium secondary battery) is not included
in the MS-374 complete board.
注意
電池の交換は，正しく行わないと破裂する恐れがあり
ます。電池を交換する場合には必ず同じ型名の電池
4-70 JK-342, ST-175, MS-374
BL-013 (2 layers), FP-515 (2 layers), FP-546 (1 layer)

BL-013 BOARD (SIDE A) BL-013 BOARD (SIDE B)
: SR7/SR7E/SR8/SR8E : SR7/SR7E/SR8/SR8E 1
2
S001
PANEL REVERSE
1
R5904
8 7
R5901 ( DETECT )
RB5901
21
20 4
2 1
(EVF BACKLIGHT)
A
CN5902
CN5901
C5901
D5901
K
2
D5902
1
C5903
20
C5902 R5902
1-873-217- 11
08 08
1-873-217- 11

1
51
LND051
LND103 R8416 LND050
LND049
LND104 R8415 LND048
LND105 LND047
LND046
LND106 R8414 LND045
LND107 R8413 LND044
LND043
LND108 LND042
LND109
R8412 LND041
R8411 LND040
LND110 LND039
LND038
LND111 R8410 LND036
LND037
LND112 R8409 LND035
LND113 LND034
LND033
LND114 R8408 LND032
LND115
R8407 LND030
LND031
LND116 LND029
R8406 LND028
LND117 R8405 LND027
LND026
LND118 LND025
LND119 R8404 LND024
LND023
LND120 R8403 LND022
LND021
LND121 LND020
LND122
R8402 LND019
LND018
LND123 LND017
LND124 R8401 LND016
LND015
LND125 LND014
LND013
LND126 LND012
LND011
LND127 LND010
LND128 LND009
LND008
LND129 LND007
LND006
LND130 LND005
LND131 LND004
LND003
LND132 LND002
LND001
LND133
LND134 1
LND135
LND136 1-870-462- 11
LND137
LND138
LND139
LND140
40
08
LND006
LND005
LND004
LND003
LND002
08 1-871-052- LND001
11
4-71 BL-013, FP-515, FP-546
Ver. 1.1 2007.06
FP-717 (1 layer), FP-718 (2 layers), FP-719 (2 layers), FP-729 (1 layer),

: SR7/SR7E/SR8/SR8E
LND006
LND001
LND002
LND003
LND004
LND005
LND007
LND008
LND009
LND010
LND011
LND012
LND013
LND014
LND015
LND016
LND017
LND018
LND019
LND020
LND021
LND022
LND023
LND024
LND001
LND002
LND003
LND004
1
LND005
CN7171
LND006
6
1-873-192- 11
LND025
LND026
MANUAL
1 2
S7171
3 4
22 20
19 1
08
1-873-194- 11
23 21
08
CN7191
HDMI
Note: CN7191 is not supplied, but this is included

in the FP-719 flexible complete board.

LND052
D7292
1 4
(TALLY)
LND051 IC7291
LND050
LND049
LND048
LND047
LND046
LND045
LND044
LND043 2 3
1
LND042
2
LND041
LND040
LND039
LND038
LND037
LND036 D7291 C7291
LND035
LND034 (NIGHT SHOT)
LND033
LND032
LND031
LND030
LND029 LND008
LND028
CN7181
LND027 LND007
LND026 LND006
LND025
LND024 LND005
LND023
LND022 LND004
LND021 LND003
LND020
LND019 LND002
LND018
LND017 LND001
LND016
LND015
LND013
LND014
1-873-205- 11
LND012
LND011
LND010
08
41
LND009
42
LND008
LND007
LND006
LND005
LND004
LND003
LND002
LND001
08
Note: CN7181 is not supplied, but this is included 1-873-193- 11

in the FP-718 flexible complete board.
4-72E FP-717, FP-718, FP-719, FP-729
NOTE
5. REPAIR PARTS LIST

NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.
Link EXPLODED VIEWS
A B C D
OVERALL SECTION-1 OVERALL SECTION-2 OVERALL SECTION-3 CABINET (L) SECTION-1
E F G H
LENS SECTION LENS SECTION
CABINET (L) SECTION-2 CABINET (F) BLOCK (SR7/SR7E/SR8/SR8E) (SR5/SR5C/SR5E)
I J K L
EVF BLOCK
CABINET (R) SECTION LCD PANEL BLOCK (SR7/SR7E/SR8/SR8E) BT PANEL BLOCK
Link ELECTRICAL PARTS LIST ACCESSORIES
BL-013 BOARD K FP-718 FLEXIBLE BOARD A FP-729 FLEXIBLE BOARD E
CK-183 BOARD I FP-719 FLEXIBLE BOARD E JK-342 BOARD E
FP-515 FLEXIBLE BOARD A FP-720 FLEXIBLE BOARD L MS-374 BOARD L
FP-546 FLEXIBLE BOARD J FP-721 FLEXIBLE BOARD D PD-324 BOARD J
FP-717 FLEXIBLE BOARD F FP-722 FLEXIBLE BOARD E ST-175 BOARD G
(ENGLISH)
NOTE: When indicating parts by reference number,
• -XX, -X mean standardized parts, so they may have some differences from please include the board name.
the original one.
• Items marked “*” are not stocked since they are seldom required for routine The components identified by mark 0 or
service. Some delay should be anticipated when ordering these items. dotted line with mark 0 are critical for safety.
• The mechanical parts with no reference number in the exploded views are not Replace only with part number specified.
supplied. Les composants identifiés par une marque
• Due to standardization, replacements in the parts list may be different from 0 sont critiques pour la sécurité.
the parts specified in the diagrams or the components used on the set. Ne les remplacer que par une pièce portant
• CAPACITORS: le numéro spécifié.
uF: µF
• COILS
uH: µH
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
• SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , uPC... , µPC... ,
uPD..., µPD...
(JAPANESE)
【使用上の注意】
• ここに記載されている部品は, 補修用部品であるため, 回路図及びお願い
セットに付いている部品と異なる場合があります。図面番号で部品を指定するときは基板名又はブロック
• -XX, -Xは標準化部品のため, セットに付いている部品と異なる場を併せて指定してください。
合があります。
• *印の部品は常備在庫しておりません。 0印の部品，または0印付の点線で囲まれた部品は，
• コンデンサの単位でuFはμFを示します。安全性を維持するために，重要な部品です。
• 抵抗の単位Ωは省略してあります。従って交換時は，必ず指定の部品を使用してください。
金　　被：金属被膜抵抗。
サンキン：酸化金属被膜抵抗。
• インダクタの単位でuHはμHを示します。
• 半導体の名称でuA..., uPA..., uPB..., uPC..., uPD...等はそれぞれμ
A..., μPA..., μPB..., μPC..., μPD...を示します。
5-1
DISASSEMBLY HARDWARE LIST

5-1. EXPLODED VIEWS
ns: not supplied
#2
9
(Note 1)
ns
8
2
6
#2
#14 #8
7
4
5
(Note 2)
3
ns Overall Section-2
(See Page 5-3)
ns
#2
#2
Note 1 : Refer to page 1-13 “Precaution on replacing the cabi- Note 1 : キャビネット (G) 組立の交換時は1-13ページの “キャビネット
net (G) assy” when changing the cabinet (G) assy. (G) 組立交換時の注意” を参照してください。
Note 2 : Be sure to read “HELP” when attach the FP-718 flex- Note 2 : FP-718フレキシブル基板取付時は“HELP”を必ずお読みく
ible board. ださい。
Ref. No. Part No. Description Ref. No. Part No. Description
1 A-1317-545-A CABINET (SERVICE), BOTTOM 8 1-797-808-11 HDD (MK4009GAL-40GB) (SR5/SR5E)
2 2-589-376-01 FOOT (395), RUBBER 8 1-797-867-11 HDD (MK1011GAH-100GB) (SR5C/SR8/SR8E)
* 3 3-213-064-01 SCREW, TRIPOD
* 4 3-213-066-01 FRAME, BOTTOM CABINET 9 (Note 1) CABINET (G) ASSY
5 A-1274-040-A FP-718 FLEXIBLE BOARD, COMPLETE (Note 2)
#2 2-635-562-31 SCREW (M1.7) (Black)
6 A-1202-561-A FP-515 FLEXIBLE BOARD, COMPLETE #8 3-078-890-01 SCREW, TAPPING (Silver)
7 2-697-545-01 DAMPER, DM #14 2-599-475-11 SCREW (M1.7) (Silver)
8 1-797-659-11 HDD (MK6008GAH-60GB) (SR7/SR7E)
5-2
SR5/SR5C/SR5E SR7/SR7E/SR8/SR8E SR7/SR7E/SR8/SR8E
52 52
#2
51 #2 51 #2
#2
EVF Block
(SR7/SR7E/SR8/SR8E)
(See Page 5-12)
#2
#2
SR7/SR7E/
#2 SR8/SR8E
BT Panel Block
(See Page 5-13) #2
#2
Overall Section-3 Cabinet (R) Section

(See Page 5-4) (See Page 5-10)
#2
51 3-212-977-01 CABINET (T (255)) (SR7:J) 52 X-2178-752-1 COVER (255B) ASSY, SHOE
51 3-212-977-11 CABINET (T (255)) (SR7:US, CND, E, KR, JE/ (SR7:US, CND, E, KR, JE/SR7E/SR8/SR8E)
SR7E/SR8:US, CND, E, KR, JE/SR8E) 52 X-2178-753-1 COVER (253) ASSY, SHOE (SR5/SR5C/SR5E)
51 3-212-977-21 CABINET (T (255)) (SR8:J)
51 X-2178-757-1 CABINET (T (253)) ASSY (SR5/SR5C/SR5E) #2 2-635-562-31 SCREW (M1.7) (Black)
52 X-2178-751-1 COVER (255C) ASSY, SHOE (SR7:J)
5-3
101
#12
#2 SR5/SR5C/SR5E
#14
Cabinet (F) Block

(See Page 5-7)
#2
SR7/SR7E/
SR8/SR8E
(Note)
Cabinet (L) Section-1
(See Page 5-5)
Cabinet (F) Block

(See Page 5-7)
#2
Note: Refer to page 2-1 “Note for disconnec-

tion the harness” when changing the har-
ness.
Note: HARNESS (COAXIAL CABLE) の交換

時は2-1ページ “Note for disconnection
the harness” を参照して下さい。
101 1-480-164-11 SWITCH BLOCK, CONTROL (PS25500) #2 2-635-562-31 SCREW (M1.7) (Black)
(SR7:J/SR8:J) #12 3-080-204-21 SCREW, TAPPING, P2 (Black)
101 1-480-164-21 SWITCH BLOCK, CONTROL (PS25500) #14 2-599-475-11 SCREW (M1.7) (Silver)
(SR7:US, CND, E, KR, JE/SR7E/SR8:US, CND,
E, KR, JE/SR8E)
101 1-480-164-41 SWITCH BLOCK, CONTROL (PS25500)
(SR5/SR5C/SR5E)
5-4
ns: not supplied
159 #14
J7211 153
Cabinet (L) Section-2
(See Page 5-6)
J7212
152 #14
#14
154
#3
#14
#3
SR7/SR7E/ 155 162
SR8/SR8E
161 #12
156
ns
157
ns
151 4
#8 - 50
VC
SR7/SR7E/
#12
SR8/SR8E
SR5/SR5C/SR5E
158 #3
ns
MIC901
• Refer to page 5-1 for mark 0.
151 X-2178-754-1 HOLDER ASSY, MICROPHONE (SR7:J) 157 A-1274-789-A VC-504 BOARD, COMPLETE (SREVICE)
151 X-2178-755-1 HOLDER (255B) ASSY, MICROPHONE (SR5E)
(SR7:US, CND, E, KR, JE/SR7E/SR8/SR8E) * 158 3-214-816-01 CUSHION (253), SILENCE (SR5/SR5C/SR5E)
151 X-2178-756-1 HOLDER (253) ASSY, MICROPHONE 159 1-818-890-11 CONNECTOR, EXTERNAL (HOT SHOE)
(SR5/SR5C/SR5E) * 161 3-269-692-01 SHEET (SMALL), ABSORBING
152 1-873-196-11 FP-721 FLEXIBLE BOARD
153 1-873-200-11 FP-725 FLEXIBLE BOARD * 162 3-269-691-01 SHEET (LARGE), ABSORBING
154 3-212-974-01 FRAME, SHOE J7211 1-793-995-21 JACK, SUPER SMALL TYPE (REMOTE)
* 155 2-673-770-01 GASKET (D) 0 J7212 1-815-792-11 CONNECTOR, DC-IN (7.2V) (DC IN)
156 3-212-973-01 FRAME, MAIN MIC901 1-542-711-31 MICROPHONE UNIT
157 A-1274-786-A VC-504 BOARD, COMPLETE (SREVICE)
(SR7/SR8) #3 2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red)
157 A-1274-787-A VC-504 BOARD, COMPLETE (SREVICE) #8 3-078-890-01 SCREW, TAPPING (Silver)
(SR7E/SR8E) #12 3-080-204-21 SCREW, TAPPING, P2 (Black)
#14 2-599-475-11 SCREW (M1.7) (Silver)
157 A-1274-788-A VC-504 BOARD, COMPLETE (SREVICE)
(SR5/SR5C)
5-5
Ver. 1.1 2007.06
ns: not supplied
213
212
211
#2
208
214
207
ns
#2 #12
SR7/SR7E/
SR8/SR8E 209
215
210
206
ns
219
ns
#12
218
#12
205
SR7/SR7E/SR8/SR8E 204
J7222 203 #3
202
#12
201 J7221
216 217
#14
#3
201 A-1274-042-A FP-729 FLEXIBLE BOARD, COMPLETE * 213 3-213-060-01 RETAINER, D TERMINAL
* 202 3-213-057-01 FRAME (F), JACK 214 1-873-201-11 FP-726 FLEXIBLE BOARD
(SR7/SR7E/SR8/SR8E) 215 3-213-160-01 COVER (DC), JACK
* 204 3-213-058-01 FRAME (HDMI), JACK * 216 3-269-696-01 SHEET, TALLY LIGHT INTERCEPTION
205 A-1274-041-A FP-719 FLEXIBLE BOARD, COMPLETE * 217 3-269-693-01 GUARD, MIC FLEXIBLE (SR7/SR7E/SR8/SR8E)
* 218 3-269-695-01 CUSHION (REAR), HDMI
206 X-2178-750-1 COVER (MICHP) ASSY, JACK * 219 3-269-694-01 CUSHION (FRONT), HDMI
(SR7/SR7E/SR8/SR8E)
207 X-2178-749-1 COVER (HDMI) ASSY, JACK J7221 1-569-950-41 JACK (SMALL TYPE) (HEADPHONE)
208 X-2178-739-1 CABINET (L (255)) ASSY (SR7/SR7E/SR8/SR8E)
(SR7/SR7E/SR8/SR8E) J7222 1-691-737-41 JACK (SMALL TYPE) (MIC (PLUG IN POWER))
208 X-2178-740-1 CABINET (L (253)) ASSY (SR5/SR5C/SR5E) (SR7/SR7E/SR8/SR8E)
209 2-664-928-31 BELT, GRIP
#2 2-635-562-31 SCREW (M1.7) (Black)
210 3-213-124-01 COVER (REMOTE), JACK #3 2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red)
* 211 3-213-059-01 FRAME (R), JACK #12 3-080-204-21 SCREW, TAPPING, P2 (Black)
212 A-1274-034-A JK-342 BOARD, COMPLETE #14 2-599-475-11 SCREW (M1.7) (Silver)
5-6
Ver. 1.1 2007.06
5-1-6. CABINET (F) BLOCK
ns: not supplied SR5/SR5C/SR5E

Lens Section
(SR5/SR5C/SR5E)
(See Page 5-9)
#12
253
(10mm × 15mm)
252
#8
251
Lens Section
(SR7/SR7E/SR8/SR8E)
(See Page 5-8)
#12
SR7/SR7E/SR8/SR8E 255
(10mm × 15mm)
252 #8
254
#14
257
#8
ns
#8
256
258
CAUTION :
For the part of 253: TAPE AS (3-079-115-01) or 255: TAPE (A (2/3)) (2-676-475-01),
cut NON WOVEN (T0.25) (3-076-631-01) into the desired length and use it.
CAUTION :
253: TAPE AS (3-079-115-01)、255: TAPE (A(2/3)) (2-676-475-01)は、
ヒメロン T0.25 (3-076-631-01) を切って使用して下さい。
251 X-2178-738-1 CABINET (F (253)) ASSY (SR5/SR5C/SR5E) 255 CAUTION TAPE (A(2/3)) (SR7/SR7E/SR8/SR8E)
252 A-1217-971-A LENS BARRIER UNIT 256 A-1274-039-A FP-717 FLEXIBLE BOARD, COMPLETE
253 CAUTION TAPE AS (SR5/SR5C/SR5E) (SR7/SR7E/SR8/SR8E)
254 X-2178-735-1 CABINET (F (255C)) ASSY (SR7:J) 257 1-479-004-21 SWITCH BLOCK, CONTROL (AD11800)
254 X-2178-736-1 CABINET (F (255B)) ASSY (SR8:J) (SR7/SR7E/SR8/SR8E)
258 X-2178-734-1 BASE ASSY, AD (SR7/SR7E/SR8/SR8E)
254 X-2178-737-1 CABINET (F (255B)) ASSY (E)
(SR7:US, CND, E, KR, JE/SR7E/SR8:US, CND, #8 3-078-890-01 SCREW, TAPPING (Silver)
E, KR, JE/SR8E) #12 3-080-204-21 SCREW, TAPPING, P2 (Black)
#14 2-599-475-11 SCREW (M1.7) (Silver) (SR7/SR7E/SR8/SR8E)
5-7
Ver. 1.1 2007.06
5-1-7. LENS SECTION (SR7/SR7E/SR8/SR8E) 306
ns: not supplied ns

5
#3 -17 C5206
ST
303 #14
#23
301 305 307

304 #23
ns
#14 IC6701
302 (Note1, 2) ns
CM
#14 -07
7
308
#23 312
ns
ns
309
310 (Note3)
311
313 #14
316
8
2
#14
-2
#23
D
L
317 #14
#3
314 ns
315
Note 1: IC6701 is not supplied, but this is
included in CMOS block assy.
Note 1: IC6701は交換対象ではありません
が，CMOS部組に含まれます。
Note 2: Be sure to read “Precautions for Re- Note 3: Refer to page 2-1 “Note for disconnec-
placement of Imager” on page 4-3 tion the harness” when changing the har-
when changing the imager. ness.
Note 2: イメージャの交換時は4 - 4 ページ Note 3: HARNESS (COAXIAL CABLE) の交換

の “イメージャ交換時の注意” を必時は2-1ページ “Note for disconnection
ずお読みください。 the harness” を参照して下さい。
* 301 3-213-042-01 SHEET (255), VC INSULATING 312 A-1227-735-A LSV-1190A (SERVICE)
* 302 3-213-033-01 FRAME (L (255)), LENS * 313 3-213-036-01 CLAMP, HARNESS
0 303 1-480-263-11 FLASH UNIT 314 A-1274-032-A LD-228 (FIR) BOARD, COMPLETE
304 X-2176-859-1 HOLDER ASSY, ST 315 1-873-198-11 FP-723 FLEXIBLE BOARD
* 305 3-213-035-01 HOLDER, CAPACITOR
* 316 3-213-037-01 GUARD, BARRIER FLEXIBLE
306 A-1274-038-A ST-175 BOARD, COMPLETE * 317 3-213-034-01 FRAME (R (255)), LENS
308 A-1237-309-A CM-077 BOARD, COMPLETE (SERVICE) 0*C5206 1-114-393-11 CAP, ELECT 70MF 330V
309 1-965-256-11 HARNESS (COAXIAL CABLE) (Note3) IC6701 A-1209-688-A CMOS BLOCK ASSY (CMOS IMAGER)(Note1, 2)
310 2-698-010-01 RUBBER (1190), SEAL
#3 2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red)
311 1-788-558-11 FILTER BLOCK, OPTICAL #14 2-599-475-11 SCREW (M1.7) (Silver)
#23 3-080-204-11 SCREW, TAPPING, P2 (Black)
5-8
Ver. 1.1 2007.06
5-1-8. LENS SECTION (SR5/SR5C/SR5E) 356
ns: not supplied ns

5
#3 -17 C5206
ST
353
#23
#14
351 357
#14
354
355 ns
352 358 #23
IC6901
#23 (Note1, 2)
360 CM
-07
6
362 361
ns
ns
359
(Note3)
363 #14
#23
8
2
-2
#23
D
L
#3
365
364
#14
366 ns
Note 1: IC6901 is not supplied, but this is
included in CMOS block assy.
Note 1: IC6901は交換対象ではありません
が，CMOS部組に含まれます。
Note 2: Be sure to read “Precautions for Re- Note 3: Refer to page 2-1 “Note for disconnec-
placement of Imager” on page 4-3 tion the harness” when changing the har-
when changing the imager. ness.
Note 2: イメージャの交換時は4 - 4 ページ Note 3: HARNESS (COAXIAL CABLE) の交換

の “イメージャ交換時の注意” を必時は2-1ページ “Note for disconnection
ずお読みください。 the harness” を参照して下さい。
* 351 3-213-045-01 SHEET (253), VC INSULATING 362 8-848-825-01 DEVICE, LENS LSV-942C
* 352 3-213-043-01 FRAME (L (253)), LENS * 363 3-213-036-01 CLAMP, HARNESS
0 353 1-480-263-11 FLASH UNIT 364 A-1274-033-A LD-228 (FIY) BOARD, COMPLETE
354 X-2176-859-1 HOLDER ASSY, ST 365 1-873-198-11 FP-723 FLEXIBLE BOARD
* 355 3-213-035-01 HOLDER, CAPACITOR
* 366 3-213-044-01 FRAME (R (253)), LENS
356 A-1274-038-A ST-175 BOARD, COMPLETE
357 1-873-199-11 FP-724 FLEXIBLE BOARD 0*C5206 1-114-393-11 CAP, ELECT 70MF 330V
358 A-1231-932-A CM-076 BOARD, COMPLETE IC6901 A-1172-742-A CMOS BLOCK ASSY (CMOS IMAGER)(Note1, 2)
359 1-965-258-71 HARNESS (COAXIAL CABLE) (Note3)
360 2-629-086-01 RUBBER (871), SEAL #3 2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red)
#14 2-599-475-11 SCREW (M1.7) (Silver)
361 1-788-382-11 OPTICAL FILTERBLOCK (OFB-03-26) #23 3-080-204-11 SCREW, TAPPING, P2 (Black)
5-9
5-1-9. CABINET (R) SECTION
ns: not supplied
LCD Panel Block

SP901 (See Page 5-11)
401
#8
402
CK #12
-18
#8 3 406
#8
#12
407
#12 ns
403 #14
405
404
408
401 3-213-049-01 FRAME, SP RETAINER * 407 3-270-566-01 SHEET, WATERPROOF
402 A-1274-036-A CK-183 BOARD, COMPLETE * 408 3-218-521-01 SHEET, FLEXIBLE ELECTROSTATIC
* 403 3-213-050-01 FRAME, CABINET (R)
404 1-873-203-11 FP-727 FLEXIBLE BOARD SP901 1-825-262-82 LOUD SPEAKER (1.6CM)
405 1-480-165-11 SWITCH BLOCK, CONTROL (SB25500)
#8 3-078-890-01 SCREW, TAPPING (Silver)
406 3-213-048-01 COVER, HINGE BLIND #12 3-080-204-21 SCREW, TAPPING, P2 (Black)
#14 2-599-475-11 SCREW (M1.7) (Silver)
5-10
ns: not supplied

452 458
(Note)
451
(Note)
E 457
#2
#12
459
ns
456
(3.3mm × 3.8mm)
A
460
455
454
453
#8
466 461
PD 462
#2 -32 463 472
4
464
A
465
B E
C
D
467
468 D
Note : Be sure to read “HELP” when you

install the FP-537 flexible board and B
FP-546 flexible board. C 470
471
Note : FP-537フレキシブル基板, FP-546
フレキシブル基板取付時は“HELP” 469
を必ずお読み下さい。
LCD901
CAUTION : CAUTION :
For the part of 456: SHEET, HINGE ADHESIVE 456: ヒンジ接着紙 (3-089-465-01)
(3-089-465-01), cut SHEET, ADHESIVE は、接着紙 (2-649-300-01) を切って
(2-649-300-01) into the desired length and use it. 使用して下さい。
451 1-870-992-11 FP-537 FLEXIBLE BOARD (Note) 464 2-666-801-01 LIGHT GUIDE (2.7)
452 A-1239-340-A FP-546 FLEXIBLE BOARD, COMPLETE (Note) 465 2-894-347-01 REFLECTION SHEET (2.7J)
453 3-213-051-01 COVER (O), PANEL HINGE (SR7:J) 466 A-1242-019-A PD-324 BOARD, COMPLETE
453 3-213-051-11 COVER (O), PANEL HINGE * 467 2-638-780-01 CLIP
(SR7:US, CND, E, KR, JE/SR7E/SR8/SR8E)
453 3-213-051-21 COVER (O), PANEL HINGE (SR5/SR5C/SR5E) 468 X-2178-743-1 CABINET (C (255C)) ASSY, P (SR7:J)
468 X-2178-744-1 CABINET (C (255B)) ASSY, P
* 454 3-096-413-01 CLAMP, FLEXIBLE (SR7:US, CND, E, KR, JE/SR7E)
455 X-2108-475-1 HINGE ASSY 468 X-2178-745-1 CABINET (C (253)) ASSY, P (SR5/SR5C/SR5E)
456 CAUTION SHEET, HINGE ADHESIVE 468 X-2179-066-1 CABINET (C (SR8B)) ASSY, P (SR8/SR8E)
457 3-213-052-01 COVER (U), PANEL HINGE * 469 2-672-277-01 CUSHION, TP
458 X-2178-741-1 CABINET (R) ASSY (E) (EXCEPT SR7:J/SR8:J)
* 470 3-213-054-01 FRAME, PANEL GROUND
458 X-2178-742-1 CABINET (R) ASSY (SR7:J/SR8:J) 471 1-479-995-11 KEY BLOCK, CONTROL (SB22200)
459 2-887-999-01 FRONT FRAME (2.7J) 472 3-213-053-01 CABINET (M), P (SR7:J/SR8:J)
460 2-666-807-02 AG SHEET (2.7) 472 3-213-053-11 CABINET (M), P (EXCEPT SR7:J/SR8:J)
461 2-666-802-01 PRISM SHEET V (2.7)
462 2-666-803-01 PRISM SHEET H (2.7) LCD901 A-1202-059-A TP BLOCK ASSY (27ESTMG07)
463 2-666-804-01 DIFFUSION SHEET (2.7) #2 2-635-562-31 SCREW (M1.7) (Black)

#8 3-078-890-01 SCREW, TAPPING (Silver)
5-11
HARDWARE LIST
5-1-11. EVF BLOCK (SR7/SR7E/SR8/SR8E)
508
507
509
510
LCD902
506
505
501 504
503
502
#12
511
512
513
#12
501 A-1274-035-A BL-013 BOARD, COMPLETE 509 X-2178-733-1 EYE CUP ASSY
502 2-664-672-01 GUIDE, LAMP
* 503 2-638-819-01 CUSHION, LCD * 510 2-668-134-01 PANEL (CF), POLARIZATION
* 504 2-638-818-01 ILLUMINATOR 511 3-213-062-01 CABINET (LOWER), VF
* 505 2-638-816-01 PLATE (TFT), DEFLECTION 512 1-873-204-11 FP-728 FLEXIBLE BOARD
513 X-2178-732-1 BASE ASSY, VF TILT
506 2-664-671-01 SPACER, LCD
* 507 2-699-236-01 CABINET (222), INNER LCD902 8-753-241-14 LCX076AKE-1
508 3-213-061-01 CABINET (UPPER), VF (SR7:J)
508 3-213-061-11 CABINET (UPPER), VF #12 3-080-204-21 SCREW, TAPPING, P2 (Black)
(SR7:US, CND, E, KR, JE/SR7E/SR8/SR8E)
5-12
HARDWARE LIST
5-1-12. BT PANEL BLOCK
ns: not supplied
553
BH720
#12
554
552
#12
551
#12
MS
-37
4
#12
ns
BH7401
(Note) : BT7401 (BATTERY, LITHIUM SECONDARY)
Board on the mount position.
BT7401
(Note) (See page 4-70.)
Note: Replace the battery holder (BH7401) together when replacing

When mounting these parts, mount new battery holder first and CAUTION
attach new lithium battery next. Danger of explosion if battery is incorrectly replaced.
Note: MS-374基板のリチウム電池(BT7401)を交換する場合はバッテリホ
ルダ(BH7401)も同時に新品に交換して下さい。注意
(一度使用したバッテリホルダは再使用できません。) 電池の交換は，正しく行わないと破裂する恐れがあり
部品取り付けの際は、先にバッテリホルダを取り付けてからます。電池を交換する場合には必ず同じ型名の電池
リチウム電池を装着してください。又は同等品と交換してください。
551 A-1274-037-A MS-374 BOARD, COMPLETE 0 BH720 1-780-064-21 BATTERY TERMINAL BOARD
* 552 3-213-063-01 FRAME, BT TERMINAL 0 BH7401 1-756-615-31 HOLDER, BATTERY (Note)
553 1-873-195-11 FP-720 FLEXIBLE BOARD 0 BT7401 1-528-900-31 BATTERY, LITHIUM SECONDARY (Note)
554 X-2178-731-1 PANEL ASSY, BT
5-13
BL-013 CK-183
5-2. ELECTRICAL PARTS LIST

A-1274-035-A BL-013 BOARD, COMPLETE
(SR7/SR7E/SR8/SR8E)
**********************
< CAPACITOR >
C5901 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V

C5902 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
< CONNECTOR >
* CN5901 1-816-648-51 FFC/FPC CONNECTOR (LIF) 20P

* CN5902 1-817-560-71 CONNECTOR, FPC (ZIP) 21P
< DIODE >
* D5901 6-501-591-01 DIODE NESW007AT-T099 (EVF BACKLIGHT)

D5902 6-500-941-01 DIODE MAZS056008S0
< COMPOSITION CIRCUIT BLOCK >
RB5901 1-234-380-21 RES, NETWORK 47K (1005X4)

************************************************************
A-1274-036-A CK-183 BOARD, COMPLETE

**********************
< CONNECTOR >

CN6003 1-778-506-21 PIN, CONNECTOR (PC BOARD) 2P
* CN6005 1-819-572-51 CONNECTOR, FFC/FPC (LIF) 30P
< DIODE >
D6008 8-719-056-54 DIODE MAZS068008SO
< RESISTOR >
R6001 1-218-963-11 RES-CHIP 6.8K 5% 1/16W

R6002 1-218-958-11 RES-CHIP 2.7K 5% 1/16W
R6003 1-208-720-11 METAL CHIP 36K 0.5% 1/16W
< SWITCH >
S6001 1-786-515-21 SWITCH, TACTILE (RESET)

S6002 1-771-138-21 SWITCH, KEY BOARD (EASY)
S6003 1-771-138-21 SWITCH, KEY BOARD (DISP/BATT INFO)
S6004 1-771-138-21 SWITCH, KEY BOARD (PLAY)
S6005 1-786-148-11 SWITCH, PUSH (1 KEY) (PANEL OPEN/CLOSE)
S6006 1-771-138-21 SWITCH, KEY BOARD (FILM ROLL INDEX)

************************************************************
Electrical parts list of the CM-076 and CM-

077 boards is not shown.
Pages 5-15 to 5-16 are not shown.
5-14
FP-515 FP-546
FP-717 FP-718 FP-719 FP-720 FP-721 FP-722 FP-729 JK-342
A-1202-561-A FP-515 FLEXIBLE BOARD, COMPLETE 1-873-195-11 FP-720 FLEXIBLE BOARD
******************************* ********************
(BH720 is not included in the FP-720 flexible board.)
< RESISTOR >
< BATTERY TERMINAL >
R8401 1-218-929-11 RES-CHIP 10 5% 1/16W
R8402 1-218-929-11 RES-CHIP 10 5% 1/16W 0 BH720 1-780-064-21 BATTERY TERMINAL BOARD
R8403 1-218-929-11 RES-CHIP 10 5% 1/16W ************************************************************
R8404 1-218-929-11 RES-CHIP 10 5% 1/16W
R8405 1-218-929-11 RES-CHIP 10 5% 1/16W 1-873-196-11 FP-721 FLEXIBLE BOARD
********************
R8406 1-218-929-11 RES-CHIP 10 5% 1/16W (J7211 and J7212 are not included in the FP-721 flexible board.)
R8407 1-218-929-11 RES-CHIP 10 5% 1/16W
R8408 1-218-929-11 RES-CHIP 10 5% 1/16W < JACK >
R8409 1-218-929-11 RES-CHIP 10 5% 1/16W
R8410 1-218-929-11 RES-CHIP 10 5% 1/16W J7211 1-793-995-21 JACK, SUPER SMALL TYPE (REMOTE)
0 J7212 1-815-792-11 CONNECTOR, DC-IN (7.2V) (DC IN)
R8411 1-218-929-11 RES-CHIP 10 5% 1/16W ************************************************************
R8412 1-218-929-11 RES-CHIP 10 5% 1/16W
R8413 1-218-929-11 RES-CHIP 10 5% 1/16W 1-873-197-11 FP-722 FLEXIBLE BOARD
R8414 1-218-929-11 RES-CHIP 10 5% 1/16W (SR7/SR7E/SR8/SR8E)
R8415 1-218-929-11 RES-CHIP 10 5% 1/16W ********************
(J7221 and J7222 are not included in the FP-722 flexible board.)
R8416 1-218-929-11 RES-CHIP 10 5% 1/16W
************************************************************ < JACK >
A-1239-340-A FP-546 FLEXIBLE BOARD, COMPLETE J7221 1-569-950-41 JACK (SMALL TYPE) (HEADPHONE)
******************************* J7222 1-691-737-41 JACK (SMALL TYPE) (MIC (PLUG IN POWER))
************************************************************
< SWITCH >
A-1274-042-A FP-729 FLEXIBLE BOARD, COMPLETE
S001 1-786-680-21 SWITCH, DETECTION (SMD) *******************************
(PANEL REVERSE DETECT)
************************************************************ < CAPACITOR >
A-1274-039-A FP-717 FLEXIBLE BOARD, COMPLET C7291 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
(SR7/SR7E/SR8/SR8E)
****************************** < DIODE >
< CONNECTOR > D7291 6-500-512-01 DIODE CL-330IRS-X-TU (NIGHT SHOT)

D7292 8-719-064-07 DIODE SML-310LTT86 (TALLY)
< IC >
< SWITCH >
IC7291 6-600-163-01 IC RS-770
S7171 1-786-157-31 TACTILE SWITCH (MANUAL) ************************************************************
************************************************************
A-1274-034-A JK-342 BOARD, COMPLETE
A-1274-040-A FP-718 FLEXIBLE BOARD, COMPLETE **********************
*******************************
(CN7181 is not supplied, but this is included in the FP-718 flexible complete < CAPACITOR >
board.)
C7301 1-164-933-11 CERAMIC CHIP 220PF 10% 50V
< CONNECTOR > C7302 1-164-933-11 CERAMIC CHIP 220PF 10% 50V
CN7181 (Not supplied) CONNECTOR, MULTIPLE (SOCKET) < CONNECTOR >

************************************************************
CN7301 1-818-607-12 CONNECTOR, SQUARE TYPE 10P
A-1274-041-A FP-719 FLEXIBLE BOARD, COMPLETE (COMPONENT OUT)
******************************* CN7302 1-815-794-13 CONNECTOR (MULTIPLE) (AV OUT)
(CN7191 is not supplied, but this is included in the FP-719 flexible complete * CN7303 1-818-087-51 CONNECTOR, FFC/FPC (LIF) 26P
board.)
< DIODE >
< CONNECTOR >
D7301 6-500-750-01 DIODE NSAD500H-T1-A
CN7191 (Not supplied) CONNECTOR, HDMI (HDMI)
************************************************************ < FERRITE BEAD >
FB7301 1-400-927-31 BEAD, FERRITE (1005)
5-17
JK-342
FB7302 1-400-927-31 BEAD, FERRITE (1005)
FB7305 1-400-833-21 SMD EMI FERRITE
< VARISTOR >
VDR731 1-803-974-11 VARISTOR, CHIP (1608)

************************************************************
Electrical parts list of the LD-228 board is

not shown.
Pages 5-19 to 5-20 are not shown.
5-18
MS-374 PD-324
A-1274-037-A MS-374 BOARD, COMPLETE A-1242-019-A PD-324 BOARD, COMPLETE
*********************** ***********************
(BT7401 (lithium secondary battery) is not included in the MS-374 complete
board.) < CAPACITOR >
< BATTERY HOLDER >
0 BH7401 1-756-615-31 HOLDER, BATTERY (Note) C6102 1-100-581-81 CERAMIC CHIP 0.0047uF 10% 50V
C6103 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V
< BATTERY > C6105 1-127-895-91 TANTAL. CHIP 22uF 20% 4V
C6107 1-165-884-91 CERAMIC CHIP 2.2uF 10% 6.3V
0 BT7401 1-528-900-31 BATTERY, LITHIUM SECONDARY (Note)
< CAPACITOR > C6109 1-164-739-11 CERAMIC CHIP 560PF 5% 50V
C7404 1-100-786-91 TANTAL. CHIP 22uF 20% 6.3V C6112 1-100-786-91 TANTAL. CHIP 22uF 20% 6.3V
C7405 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C6113 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V
< CONNECTOR > C6114 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V
* CN7401 1-779-334-51 CONNECTOR, FFC/FPC 20P * C6116 1-112-298-91 CERAMIC CHIP 1uF 10% 16V
* CN7402 1-819-990-21 MEMORY STICK DUO CONNECTOR 10P * C6117 1-112-298-91 CERAMIC CHIP 1uF 10% 16V
C6119 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3V
< DIODE >
C6120 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V
D7401 6-501-216-01 DIODE CL-271HR-C-TS (ACCESS) C6121 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
< FERRITE BEAD > C6124 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V
FB7401 1-469-580-21 INDUCTOR, FERRITE BEAD (1005)
FB7402 1-469-580-21 INDUCTOR, FERRITE BEAD (1005) C6126 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
FB7403 1-469-580-21 INDUCTOR, FERRITE BEAD (1005)
FB7404 1-469-580-21 INDUCTOR, FERRITE BEAD (1005) < CONNECTOR >
< RESISTOR > * CN6101 1-785-905-51 FFC/CONNECTOR, FPC (ZIF) 24P

* CN6102 1-794-322-51 FFC/CONNECTOR, FPC (ZIF) 6P
R7403 1-218-944-11 RES-CHIP 180 5% 1/16W CN6104 1-816-180-71 CONNECTOR, FPC (ZIF) 6P
R7404 1-218-944-11 RES-CHIP 180 5% 1/16W * CN6105 1-785-905-51 FFC/CONNECTOR, FPC (ZIF) 24P
R7405 1-218-944-11 RES-CHIP 180 5% 1/16W
R7406 1-218-944-11 RES-CHIP 180 5% 1/16W < DIODE >
************************************************************
D6105 6-500-941-01 DIODE MAZS056008S0
Note : Replace the battery holder (BH7401) together when replacing
* D6106 6-501-597-01 DIODE NSSW008DT-T108 (LCD BACKLIGHT)
When mounting these parts, mount new battery holder
first and attach new lithium battery next.
< FERRITE BEAD >
Note :MS-374基板のリチウム電池(BT7401)を交換する場合は
バッテリホルダ(BH7401)も同時に新品に交換して下さい。 FB6101 1-400-331-11 FERRITE, EMI (SMD) (1005)
(一度使用したバッテリホルダは再使用できません。)
部品取り付けの際は、先にバッテリホルダを取り付けてから < IC >
リチウム電池を装着してください。
IC6102 8-753-229-98 IC CXM3006CR-T4
CAUTION
Danger of explosion if battery is incorrectly replaced.
< COIL >
注意 L6101 1-400-588-11 INDUCTOR 10uH
電池の交換は，正しく行わないと破裂する恐れがあり L6102 1-400-588-11 INDUCTOR 10uH
ます。電池を交換する場合には必ず同じ型名の電池 L6103 1-400-588-11 INDUCTOR 10uH
< TRANSISTOR >
Q6101 8-729-427-37 TRANSISTOR XP411F-TXE

Q6102 8-729-427-67 TRANSISTOR XP421F-TXE
Q6107 6-550-239-01 TRANSISTOR DTA144EMT2L
Q6108 6-550-234-01 TRANSISTOR UNR32A300LS0
Q6109 6-551-184-01 TRANSISTOR MCH6305-TL-E-S
Q6110 8-729-054-48 TRANSISTOR UP04601008S0

Q6111 6-550-232-01 TRANSISTOR 2SA2029T2LQ/R
5-21
PD-324 ST-175
Q6112 8-729-054-49 TRANSISTOR UP04401008S0 < TRANSISTOR >
Q6113 8-729-054-48 TRANSISTOR UP04601008S0
0*Q5201 6-551-447-01 TRANSISTOR TIG022TS-S-TL-E
< RESISTOR >
< RESISTOR >
R6101 1-218-957-11 RES-CHIP 2.2K 5% 1/16W
R6102 1-218-955-11 RES-CHIP 1.5K 5% 1/16W R5201 1-208-947-11 METAL CHIP 330K 0.5% 1/16W
R6104 1-218-990-11 SHORT CHIP 0 R5202 1-208-935-11 METAL CHIP 100K 0.5% 1/16W
R6105 1-218-954-11 RES-CHIP 1.2K 5% 1/16W R5203 1-216-864-11 SHORT CHIP 0
R6109 1-218-975-11 RES-CHIP 68K 5% 1/16W R5204 1-216-065-91 RES-CHIP 4.7K 5% 1/10W
R5205 1-216-809-11 METAL CHIP 100 5% 1/10W
R6110 1-218-949-11 RES-CHIP 470 5% 1/16W
R6112 1-208-934-11 METAL CHIP 91K 0.5% 1/16W R5206 1-218-989-11 RES-CHIP 1M 5% 1/16W
R6115 1-208-911-11 METAL CHIP 10K 0.5% 1/16W R5207 1-218-953-11 RES-CHIP 1K 5% 1/16W
R6122 1-218-965-11 RES-CHIP 10K 5% 1/16W
R6130 1-208-898-11 METAL CHIP 3K 0.5% 1/16W < TRANSFORMER >
R6132 1-218-969-11 RES-CHIP 22K 5% 1/16W 0 T5201 1-443-568-21 TRANSFORMER, D.C.-D.C.CONVERTER

R6133 1-218-977-11 RES-CHIP 100K 5% 1/16W ************************************************************
R6134 1-208-927-11 METAL CHIP 47K 0.5% 1/16W
R6135 1-218-981-81 RES-CHIP 220K 5% 1/16W
R6136 1-208-927-11 METAL CHIP 47K 0.5% 1/16W Electrical parts list of the VC-504 board is
not shown.
R6137 1-218-978-11 RES-CHIP 120K 5% 1/16W Pages 5-23 to 5-32 are not shown.
R6138 1-218-977-11 RES-CHIP 100K 5% 1/16W
R6139 1-208-699-11 METAL CHIP 4.7K 0.5% 1/16W
R6140 1-208-691-11 METAL CHIP 2.2K 0.5% 1/16W
R6141 1-208-683-11 METAL CHIP 1K 0.5% 1/16W
R6142 1-208-691-11 METAL CHIP 2.2K 0.5% 1/16W

R6143 1-218-977-11 RES-CHIP 100K 5% 1/16W
R6144 1-211-969-11 METAL CHIP 10 0.5% 1/10W
R6145 1-218-989-11 RES-CHIP 1M 5% 1/16W
R6152 1-218-990-11 SHORT CHIP 0
R6153 1-218-990-11 SHORT CHIP 0

R6154 1-218-990-11 SHORT CHIP 0
R6155 1-216-864-11 SHORT CHIP 0
************************************************************
A-1274-038-A ST-175 BOARD, COMPLETE

**********************
< CAPACITOR >

C5204 1-163-001-11 CERAMIC CHIP 220PF 10% 50V
0*C5206 1-114-393-11 CAP, ELECT 70MF 330V
< CONNECTOR >

CN5202 1-779-331-51 CONNECTOR, FFC/FPC 14P
< DIODE >
D5201 6-501-096-01 DIODE CRF02 (TE85R)

0 D5202 6-501-096-01 DIODE CRF02 (TE85R)
< IC >
0 IC5201 6-707-554-01 IC TPS65552DGQR
< COIL >
L5201 1-412-027-11 INDUCTOR 2.2uH
5-22
Ver. 1.4 2008.07
The changed portions from
Ver. 1.3 are shown in blue.
• EXCEPT J MODEL
Checking supplied accessories. to J MODEL
Power cord
AC Adaptor Operating Guide
0 1-555-074-91 (AUS)
(AC-L200/L200B) (HDR-SR5/SR5C/SR7/SR8)
0 1-790-107-42 (US, CND)
0 1-479-285-21 3-210-378-11 (ENGLISH) (US, CND, E, JE)
0 1-792-549-41 (JE)
0 1-827-269-12 (AEP, HK) 3-210-378-21 (FRENCH) (CND)
0 1-827-826-41 (UK, E: PAL) 3-210-378-31 (SPANISH) (US, E:NTSC, JE)
0 1-832-121-31 (CH) 3-210-378-41 (PORTUGUESE) (E: NTSC, JE)
0 1-833-892-21 (KR) 3-210-378-51 (TRADITIONAL CHINESE) (E: NTSC)
0 1-834-852-11 (E: NTSC) 3-210-378-61 (KOREAN) (KR, JE)
Operating Guide
(HDR-SR5E/SR7E/SR8E)
Handycam Station
3-210-379-11 (ENGLISH) (AEP, UK, AUS, E: PAL, HK, JE)
(DCRA-C181)
3-210-379-21 (FRENCH, DUTCH) (AEP)
1-821-168-21
Conversion (2P) Adaptor 3-210-379-31 (GERMAN, ITALIAN, TURKISH) (UK)
0 1-569-007-12 (E: NTSC, JE) 3-210-379-41 (SPANISH, PORTUGUESE, GREEK) (UK)
3-210-379-51 (RUSSIAN, SWEDISH) (UK, JE)
3-210-379-61 (DANISH, FINNISH, POLISH) (UK)
3-210-379-71 (CZECH, HUNGARIAN, SLOVAK) (UK)
Component video cable 3-210-379-81 (SIMPLIFIED CHINESE) (E:PAL, CH, JE)
1-829-414-61 3-210-380-31 (TRADITIONAL CHINESE) (HK)
3-210-380-41 (ARABIC, PORTUGUESE) (E: PAL)
A/V connecting cable
1-823-156-61
USB cable
DVD-ROM
1-829-579-41
"ENJOY HANDYCAM"
3-093-691-01 (KR)
ENGLESH/KOREAN/JAPANESE
3-093-691-11 (US, CND, E)
ENGLISH/FRENCH/SPANISH/PORTUGUESE
Rechargeable battery pack 3-093-691-21 (UK)
Wireless Remote Commander
(NP-FH60) ENGLISH/RUSSIAN/GERMAN
(RMT-835)
0 A-1201-666-A (US, CND) 3-093-691-51 (AEP)
1-479-275-41
0 A-1201-667-A (EXCEPT ENGLISH/FRENCH/GERMAN/DUTCH/PORTUGUESE/ITALIAN/RUSSIAN
US, CND, CH) 3-093-691-61 (E: PAL, HK, AUS, CH)
0 A-1201-668-A (CH) ENGLISH/FRENCH/SIMPLIFIED CHINESE for CHINA/
TRADITIONAL CHINESE for HONG KONG
3-093-691-71 (E: NTSC)
ENGLISH/TRADITIONAL CHINESE for TAIWAN/SPANISH/PORTUGUESE
21-Pin Adaptor
1-770-783-21 (AEP)
Handycam Handbook (PDF)

The CD-ROM supplied contains all of language version of
the Instruction Manual in pdf (Handycam Handbook.pdf) for printing.
Note: The printed matter is not supplied. If required,
please order it with the part number below.
CD-ROM "Handycam Application
Software"
3-210-374-01 (JAPANESE) (SR7/SR8) 3-210-376-11 (RUSSIAN) (SR5E/SR7E/SR8E)
(Picture Motion Browser (Software),
3-210-374-11 (ENGLISH) (SR5/SR5C/SR7/SR8) 3-210-376-21 (SWEDISH) (SR5E/SR7E/SR8E)
Picture Motion Browser Guide,
3-210-374-21 (FRENCH) (SR5/SR5C/SR7/SR8) 3-210-376-31 (DANISH) (SR5E/SR7E/SR8E)
Handycam Handbook)
3-210-374-31 (SPANISH) (SR5/SR5C/SR7/SR8) 3-210-376-41 (FINNISH) (SR5E/SR7E/SR8E)
3-214-674-01
3-210-374-41 (PORTUGUESE) 3-210-376-51 (POLISH) (SR5E/SR7E/SR8E)
(SR5/SR5C/SR7/SR8) 3-210-376-61 (CZECH) (SR5E/SR7E/SR8E)
3-210-374-51 (TRADITIONAL CHINESE) 3-210-376-71 (HUNGARIAN) (SR5E/SR7E/SR8E)
(SR5/SR5C/SR7/SR8) 3-210-376-81 (SLOVAK) (SR5E/SR7E/SR8E)
3-210-374-61 (KOREAN) (SR5/SR5C/SR7/SR8) 3-210-376-91 (SIMPLIFIED CHINESE)
3-210-375-11 (ENGLISH) (SR5E/SR7E/SR8E) (SR5E/SR7E/SR8E)
3-210-375-21 (FRENCH) (SR5E/SR7E/SR8E) 3-210-377-11 (THAI) (SR5E/SR7E/SR8E)
3-210-375-31 (GERMAN) (SR5E/SR7E/SR8E) 3-210-377-21 (INDONESIAN) (SR5E/SR7E/SR8E)
3-210-375-41 (DUTCH) (SR5E/SR7E/SR8E) 3-210-377-31 (MALAY) (SR5E/SR7E/SR8E)
3-210-375-51 (TURKISH) (SR5E/SR7E/SR8E) 3-210-377-41 (TRADITIONAL CHINESE)
3-210-375-61 (SPANISH) (SR5E/SR7E/SR8E) (SR5E/SR7E/SR8E)
3-210-375-71 (PORTUGUESE) 3-210-377-51 (ARABIC) (SR5E/SR7E/SR8E)
(SR5E/SR7E/SR8E) 3-210-377-61 (PERSIAN)
3-210-375-81 (ITALIAN) (SR5E/SR7E/SR8E) (SR5E/SR7E/SR8E)
3-210-375-91 (GREEK) (SR5E/SR7E/SR8E)
• Refer to the page 5-1 for mark 0.
5-33
Ver. 1.4 2008.07
The changed portions from
Ver. 1.3 are shown in blue.
• J MODEL
付属品
電源コード
AC アダプター取扱説明書
0 1-792-549-41
(AC-L200/L200B) 3-210-378-01 (日本語)
0 1-479-285-21
D端子コンポーネント
ハンディカムステーションビデオケーブル DVD-ROM
(DCRA-C180) 1-829-414-11 「エンジョイハンディーカム」
1-821-168-11 3-093-691-01
日本語/英語/韓国語
USBケーブル A/V接続ケーブル
1-829-579-41 1-823-156-61
リチャージャブル
バッテリーパック
0 A-1201-665-A
ワイヤレスリモコン
(RMT-835)
1-479-275-31
CD-ROM「Handycam Application
Software」ハンディカムハンドブック(PDF)
(Picture Motion Browser(ソフトウェア),
Picture Motion Browser ガイド, 印刷用の取扱説明書.pdf (ハンディカムハンドブック.pdf)は
ハンディカムハンドブック) 全ての言語が付属品のCD-ROMに含まれています。
3-214-674-01 注: 印刷物は付属されておりません。
必要な場合は下記部品番号にて注文となります。
3-210-374-01 (日本語)(SR7/SR8) 3-210-376-11 (ロシア語)(SR5E/SR7E/SR8E)

3-210-374-11 (英語)(SR5/SR5C/SR7/SR8) 3-210-376-21 (スウェーデン語)
3-210-374-21 (フランス語)(SR5/SR5C/SR7/SR8) (SR5E/SR7E/SR8E)
3-210-374-31 (スペイン語)(SR5/SR5C/SR7/SR8) 3-210-376-31 (デンマーク語)
3-210-374-41 (ポルトガル語)(SR5/SR5C/SR7/SR8) (SR5E/SR7E/SR8E)
3-210-374-51 (中国語 (繁体字))(SR5/SR5C/SR7/SR8) 3-210-376-41 (フィンランド語)
3-210-374-61 (韓国語)(SR5/SR5C/SR7/SR8) (SR5E/SR7E/SR8E)
3-210-375-11 (英語)(SR5E/SR7E/SR8E) 3-210-376-51 (ポーランド語)
3-210-375-21 (フランス語)(SR5E/SR7E/SR8E) (SR5E/SR7E/SR8E)
3-210-375-31 (ドイツ語)(SR5E/SR7E/SR8E) 3-210-376-61 (チェコ語)(SR5E/SR7E/SR8E)
3-210-375-41 (オランダ語)(SR5E/SR7E/SR8E) 3-210-376-71 (ハンガリー語)
3-210-375-51 (トルコ語)(SR5E/SR7E/SR8E) (SR5E/SR7E/SR8E)
3-210-375-61 (スペイン語)(SR5E/SR7E/SR8E) 3-210-376-81 (スロバキア語)
3-210-375-71 (ポルトガル語)(SR5E/SR7E/SR8E) (SR5E/SR7E/SR8E)
3-210-375-81 (イタリア語)(SR5E/SR7E/SR8E) 3-210-376-91 (中国語 (簡体字))
3-210-375-91 (ギリシア語)(SR5E/SR7E/SR8E) (SR5E/SR7E/SR8E)
3-210-377-11 (タイ語)(SR5E/SR7E/SR8E)
3-210-377-21 (インドネシア語)
(SR5E/SR7E/SR8E)
3-210-377-31 (マレー語)(SR5E/SR7E/SR8E)
3-210-377-41 (中国語 (繁体字))
(SR5E/SR7E/SR8E)
3-210-377-51 (アラビア語)(SR5E/SR7E/SR8E)
3-210-377-61 (ペルシャ語)(SR5E/SR7E/SR8E)
• 0マークについては，5-1ページを参照して下さい。
5-34E
RMT-835
LEVEL 2
US Model
SERVICE MANUAL Canadian Model
AEP Model
Ver. 1.2 2007. 10 UK Model
E Model
Australian Model
Hong Kong Model
Chinese Model
Korea Model
Tourist Model
Japanese Model
SUPPLEMENT-1
File this supplement with the service manual previously issued.
(DI07-142)
• Change of Repair Parts List

5-1. EXPLODED VIEWS : Points changed portion
Page Before changed After changed
5-1-1. OVERALL SECTION-1 5-1-1. OVERALL SECTION-1
5-2
8 1-797-659-11 HDD (MK6008GAH-60GB) (SR7/SR7E) 8 1-797-821-11 HDD (MK8009GAH-60GB) (SR7/SR7E)
5-1-5. CABINET (L) SECTION-2 5-1-5. CABINET (L) SECTION-2
219 219
5-6 #12 #12

218 218
#12 #12
205 205
SR7/SR7E/SR8/SR8E 204 SR7/SR7E/SR8/SR8E 204
J7222 203 #3 J7222 203 #3
2007J0800-1
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_L2 ©2007.10
& : Points added portion
: Points deleted portion
5-1-9. CABINET (R) SECTION 5-1-9. CABINET (R) SECTION
#8 18 #8 18
3 3
#8 #8
407 407
#12 #12
403 403
5-10
404 404
408
* 408 3-218-521-01 SHEET, FLEXIBLE ELECTROSTATIC ––– ––––––––– ––––––––––––––––
5-1-10. LCD PANEL BLOCK 5-1-10. LCD PANEL BLOCK
68
68
B
B LCD901 C
LCD901 C
5-11
473
––– ––––––––– –––––––––––––––– 473 2-590-635-01 TAPE AS 1/2
—2—
RMT-835
LEVEL 2
US Model
AEP Model
Ver. 1.3 2007. 11 UK Model
E Model
Australian Model
Hong Kong Model
Chinese Model
Korea Model
Tourist Model
Japanese Model
SUPPLEMENT-2
(DI07-208)
• Change of Electrical Parts List

5-2. ELECTRICAL PARTS LIST : Points changed portion
PD-324 BOARD PD-324 BOARD
5-21 * CN6101 1-785-905-51 FFC/CONNECTOR, FPC (ZIF) 24P * CN6101 1-819-913-71 CONNECTOR, FPC (ZIF) 24P
* CN6105 1-785-905-51 FFC/CONNECTOR, FPC (ZIF) 24P * CN6105 1-819-913-71 CONNECTOR, FPC (ZIF) 24P
2007K0800-1
RMT-835
LEVEL 2
US Model
AEP Model
Ver. 1.4 2008. 07 UK Model
E Model
Australian Model
Hong Kong Model
Chinese Model
Korea Model
Tourist Model
Japanese Model
SUPPLEMENT-3
(DI08-150)
• Addition of HELP
• Addition and Change of Repair Parts List
• Revision of Accessories
Note: Please refer to Ver. 1.4 of SERVICE MANUAL (9-852-202-32) for the revision of accessories.
2008G0800-1
5-1. EXPLODED VIEWS : Points added portion
5-1-5. CABINET (L) SECTION-2 5-1-5. CABINET (L) SECTION-2
ns: not supplied ns: not supplied
208 220 208
HELP
207 207
ns ns
#2 #2
5-6 SR7/SR7E/ SR7/SR7E/

SR8/SR8E SR8/SR8E
206 206
220 3-291-327-01 SHEET, HDD DAMPER
5-1-10. LCD PANEL BLOCK 5-1-10. LCD PANEL BLOCK

ns: not supplied ns: not supplied
(Note) (Note)
451 451
(Note) (Note)
E 457 E 457
#12 #12
ns ns
456 456
(3.3mm × 3.8mm) (3.3mm × 3.8mm)
A A
455 455
454 454
5-11 453 453
#8 #8
466 466
#2 #2
A A
HELP
473
468 468
* 473 3-879-389-01 SHEET (P)
—2—
HELP : Points added portion
Added contents
HDD DAMPER SHEET APPLYING POSITION
Applying
position
HDD damper sheet
Applying
position
THE METHOD OF ATTACHMENT OF FP-537 FLEXIBLE BOARD AND FP-546 FLEXIBLE COMPLETE BOARD
Be careful not to go out of

the flexible board.
Sheet (P) FP-537 flexible

board
Within 1 mm from
reinforcement plate.
—3—
HARDWARE LIST (1/4)
#1: M1.7 X 2.5 #2: M1.7 X 4.0 #3: M1.7 X 2.5 #4: M1.4 X 2.5 (Tapping)
(Black) (Black) (Red) (Dark Silver)
2-635-562-11 2-635-562-31 2-660-401-01 3-348-998-81
1.7 1.7 1.7 1.4
2.5 4.0 2.5 2.5
#5: M1.7 X 3.5 (Tapping) #6: M1.4 X 1.7 #7: M1.7 X 1.6 #8: M1.7 X 3.5 (Tapping)
(Black) (Silver) (Black) (Silver)
3-080-204-01 2-598-474-01 7-627-552-18 3-078-890-01
1.7 1.4 1.7 1.7
3.5 1.7 1.6 3.5
#9: M1.7 X 5.0 (Tapping) #10: M1.7 X 4.0 #11: M1.7 X 4.0 (Tapping) #12: M1.7 X 5.0 (Tapping)
(Silver) (Silver) (Silver) (Black)
3-078-890-21 2-599-475-31 3-078-890-11 3-080-204-21
1.7 1.7 1.7 1.7
5.0 4.0 4.0 5.0
#13: M1.7 X 2.5 (Tapping) #14: M1.7 X 2.5 #15: M1.4 X 1.5 #16: M1.4 X 2.5
(Silver) (Silver) (Silver) (Silver)
3-085-397-01 2-599-475-11 3-062-214-01 2-586-337-01
1.7 1.7 1.4 1.4
2.5 2.5 1.5

2.5
#17: M1.7 X 1.5 #18: M1.4 X 2.5 #19: M1.2 X 4.0 (Tapping) #20: M1.4 X 3.0
(Silver) (Silver) (Red) (Silver)
2-586-389-01 2-635-591-21 3-086-156-21 2-635-591-31
1.7 2.2 1.4 1.2 1.4
1.5
2.5 4.0 3.0
3.5
HARDWARE LIST (2/4)
#21: M1.4 X 3.0 #22: M1.7 X 5.0 (Tapping) #23: M1.7 X 4.0 (Tapping) #24: B1.7 X 5.5 (Tapping)
(Black) (Silver) (Black) (Black)
2-662-396-21 3-083-261-01 3-080-204-11 4-679-805-11
1.4 1.7 1.7 1.7
3.0 5.0 4.0 5.5
(Black) (Silver) (Black) (Dark Silver)
2-635-562-21 2-635-591-11 2-662-396-11 3-348-998-61
1.7 1.4 1.4 1.4
3.0 2.0 2.0 4.0
#29: M1.4 X 2.5 #30: M1.2 X 4.0 (Tapping) #31: M3.0 X 4.0 #32: M2.0 X 4.5 (Tapping)
(Black) (White) (Silver) (Silver)
2-662-396-01 3-086-156-11 2-102-434-01 2-102-498-01
1.4 1.2 3.0 2.0
2.5 3.5 4.0 4.5
(Silver) (Black) (Silver) (Silver)
3-077-331-21 3-077-331-41 3-975-291-02 4-886-821-11
3.0 3.0 4.0 3.0
6.0 8.0 6.0 6.0
#37: M2.0 X 6.0 (Tapping) #38: M3.0 X 20.0 (Tapping) #39: M2.6 X 5.0 (Tapping) #40: M2.0 X 4.0 (Tapping)
3-080-206-31 7-685-651-79 7-685-791-09 7-685-851-04
3.0
2.0 2.6 2.0
20.0
6.0 5.0 4.0
HARDWARE LIST (3/4)
#41: M3.0 X 8.0 (Tapping) #42: M2.0 X 4.0 (Tapping) #43: M1.7 X 4.0 #44: M1.7 X 3.0 (Tapping)
3-065-748-01 7-628-253-00 2-660-401-31 3-078-890-61
3.0 2.0 1.7 1.7
8.0 4.0 4.0 3.0
(Silver) (Red) (Silver) (Silver)
2-587-151-01 2-660-401-11 2-665-774-01 3-973-497-91
1.4 1.7 1.4 1.7
2.5 3.0 3.0 2.5
(Black) (Red) (Silver) (Black)
2-630-005-31 2-891-494-11 3-073-686-01 3-080-206-11
2.0 2.0 2.0 2.0
4.0 3.0 4.0

2.5
#53: M2.0 X 5.0 (Tapping) #54: M1.75 X 6.0 (Tapping) #55: M2.0 X 4.0 #56: M2.0 X 3.5
(Black) (Black) (Silver) (Silver)
3-080-206-21 3-318-203-11 2-655-582-11 3-067-187-11
2.0 1.75 2.0 2.0
5.0 6.0 4.0 3.5
#57: M1.7 X 4.0 #58: M2.0 X 6.0 (Tapping) #59: M2.0 X 5.0 (Tapping) #60: M2.6 X 5.0
(Black) (Silver) (Silver) (Black)
7-627-852-18 3-719-408-11 3-080-205-21 3-061-062-11
1.7 2.0 2.0 2.6
4.0 6.0 5.0 5.0

HARDWARE LIST (4/4)
7-682-549-09 3-080-202-21 3-060-811-21 2-666-551-21
3.0 2.0 5.0 1.7
10.0 12.5
3.0 5.0
#65: M1.4 X 3.5 #66: M1.4 X 1.4 #67: M1.4 X 2.0 #68: M1.7 X 4.0
(Silver) (Silver) (Silver) (Silver)
2-635-591-01 2-635-591-41 3-389-523-16 2-655-581-01
1.4 1.4 1.4 1.7
3.5 1.4 2.0 4.0
#69: M1.7 X 3.0 #70: M1.7 X 5.0 #71: M1.4 X 2.0 #72: M1.4 X 2.0
2-599-475-21 2-599-475-41 3-208-537-01 4-663-621-41
1.7 1.7 1.4 1.4
3.0 5.0 2.0

2.0
#73: M1.2 X 4.0 (Tapping) #74: M1.7 X 6.0 (Tapping) #75: M1.7 X 3.5 (Tapping) #76: M1.7 X 4.0 (Tapping)
(Black) (Silver) (Silver) (Silver)
3-086-156-61 2-666-551-31 2-666-551-01 2-666-551-11
1.2 1.7 1.7 1.7
4.0 6.0 3.5 4.0
#77: M1.2 X 5.0 (Tapping)

(Silver)
3-086-156-31
1.2
5.0
About this service manual
For the promotion of browse in the PDF format, the “TABLE OF CONTENTS” was eliminated. As an alternative means, use a conven-
tional function, "Bookmark". It will help you search/display not all pages but the desired page. In addition, the page layout was changed
so that each page is positioned in the center to improve the visibility on the screen.
In the circuit diagram section, the symbols (such as @001) indicating internal connections of the divided circuit diagrams were eliminated.
As an alternative function, the "Signal Location" is added. Except "GND", the divided signal names are listed in alphabetical order for
easy search of the divided circuit diagrams (division numbers) and addresses.
Example:
Address
Division number
Signal name
Of course, you can find the desired location by entering the signal name using the search function of the Acrobat, but it will take time to
locate the one you want because the same words exist to and fro in the service manual.
In the PWB drawing section, the “MOUNTED PARTS LOCATION” was eliminated. To check the mounted part location, look at the
enlarged view of the printed wiring board on which the desired part is mounted and enter the reference number for search with the Acrobat
search function. If the corresponding part is found, it is highlighted and displayed in the center of the screen.
Reverse 985220235.pdf
Revision History
S.M. Rev.
Ver. Date History Contents
issued
1.0 2007.05 Official Release — —
1.1 2007.06 Revised-1 • Correction of Model information table Yes
• Correction of BLOCK DIAGRAMS,
SCHEMATIC DIAGRAMS, PRINTED
WIRING BOARDS
• Correction of EXPLODED VIEWS
• Correction of Accessories
S.M. Correction: Page 5, 3-1, 3-4, 3-5, 3-6,
3-7, 4-1, 4-2,
4-2. SCHMATIC DIAGRAMS
4-33, 4-38, 4-49, 4-72, 5-6,
5-7, 5-8, 5-9, 5-33, 5-34
1.2 2007.10 Supplement-1 • Change of Repair Parts List No
(DI07-142)
1.3 2007.11 Supplement-2 • Change of Repair Parts List No
(DI07-208)
1.4 2008.07 Supplement-3 • Addition of HELP Yes
(DI08-150) • Addition and Change of Repair Parts List
• Revision of Accessories
S. M. Revised: Page 5-33, 5-34

Sony Hdr-sr5 Sr7 Sr8 Level-2 Ver-1.4 Rev-1 SM

Uploaded by

Copyright:

Available Formats

Sony Hdr-sr5 Sr7 Sr8 Level-2 Ver-1.4 Rev-1 SM

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sony Hdr-sr5 Sr7 Sr8 Level-2 Ver-1.4 Rev-1 SM

Uploaded by

Copyright:

Available Formats

HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E

SERVICE MANUAL LEVEL 2

SPECIFICATIONS DISASSEMBLY SCHEMATIC DIAGRAMS

MODEL INFORMATION TABLE BLOCK DIAGRAMS PRINTED WIRING BOARDS

SERVICE NOTE FRAME SCHEMATIC DIAGRAM REPAIR PARTS LIST

• Precaution on Replacing the VC-504 Board

DIGITAL VIDEO CAMERA RECORDER

Model information table

Model SR7E SR8 SR8E

SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT

After correcting the original service problem, perform the following

1-1. POWER SUPPLY DURING REPAIRS

1-2. SELF-DIAGNOSIS FUNCTION

Viewfinder or LCD screen

Repaired by: Block Detailed Code

1-2-3. Self-diagnosis Code Table

Block Detailed Symptom/State Correction

C 0 4 0 0 Non-standard battery is used. Use the InfoLITHIUM battery.

E 3 1 0 0 Drive fault Inspect or replacement of the hard disk drive.

The abnormalities in initialization of

1-3. METHOD OF COPING WITH SHIFT LENS ERROR (SR7/SR7E/SR8/SR8E)

about 330 msec

LD-228 BOARD (SIDE A) VC-504 BOARD (SIDE A)

1-3-1. E : 62 : 02 [Abnormality of IC for Steadyshot] Occurred (SR7/SR7E/SR8/SR8E)

1-3-2. E : 62 : 11 [Shift Lens Overheating (Pitch)] Occurred (SR7/SR7E/SR8/SR8E)

Order Block Page Address Data Procedure

1-3-3. E : 62 : 12 [Shift Lens Overheating (Yaw)] Occurred (SR7/SR7E/SR8/SR8E)

Order Block Page Address Data Procedure

1-3-4. E : 62 : 20 [Abnormality of Thermistor] Occurred (SR7/SR7E/SR8/SR8E)

1-4. PRECAUTION ON REPLACING THE VC-504 BOARD

USB SERIAL No.

1-5. PROCESS AFTER FIXING FLASH ERROR

対応者分類 ブロック分類 詳細コード

対 ブロック 詳細 症状／状態 対応／方法

対 ブロック 詳細 症状／状態 対応／方法

シフトレンズオーバーヒート 「1-3-3. E：62：12（シフトレンズオーバーヒート（YAW） ）が出

注意： レンズブロックを交換した場合は，A D J 編を参照して必要な調整項目を実施すること。調整後は手振れ補正O N の状

順序 ブロック ページ アドレス データ 作業内容

順序 ブロック ページ アドレス データ 作業内容

注意： レンズブロックを交換した場合は，A D J 編を参照して必要な調整項目を実施すること。調整後は手振れ補正O N の状

注意2 : U S 仕向けキャビネット( G ) 組立を交換した際は

注意2 : U S 仕向けキャビネット( G ) 組立を交換した際は

注意2 : U S 仕向けキャビネット( G ) 組立を交換した際は Serial No. *Manufacturing year

Part No. Description

注意2 : U S 仕向けキャビネット( G ) 組立を交換した際は Serial No. *Manufacturing year

(JAPANESE) A-1317-542-A SERVICE, (G (SR8E)) (CEH)

NOTE FOR REPAIR

• When installing a connector, don’t press down at wire of connector.

• Do not apply excessive load to the gilded flexible board.

DISCHARGING OF THE ST-175 BOARD’S CHARGING CAPACITOR (C5206)

The charging capacitor (C5206) of the ST-175 board is charged

Preparing the Short Jig Note: High-voltage cautions

NOTE FOR DISCONNECTION THE HARNESS (COAXIAL CABLE)

When disconnecting the harness (coaxial cable), do not pull the

Cabinet (L) Section BT Panel Block

2-2-2. OVERALL SECTION-2 (SR7/SR7E/SR8/SR8E)

2-2-4. OVERALL SECTION-3 2-2-10. CABINET (R) SECTION

2-2-11. LCD PANEL BLOCK

2-2-6. CABINET (L) SECTION-2 2-2-8. LENS SECTION (SR7/SR7E/SR8/SR8E)

対応者分類ブロック分類詳細コード

対ブロック詳細症状／状態対応／方法

対ブロック詳細症状／状態対応／方法

シフトレンズオーバーヒート「1-3-3. E：62：12（シフトレンズオーバーヒート（YAW））が出

注意：レンズブロックを交換した場合は，A D J 編を参照して必要な調整項目を実施すること。調整後は手振れ補正O N の状

順序ブロックページアドレスデータ作業内容

順序ブロックページアドレスデータ作業内容

注意：レンズブロックを交換した場合は，A D J 編を参照して必要な調整項目を実施すること。調整後は手振れ補正O N の状

注意2 : 　U S 仕向けキャビネット( G ) 組立を交換した際は

注意2 : 　U S 仕向けキャビネット( G ) 組立を交換した際は

注意2 : 　U S 仕向けキャビネット( G ) 組立を交換した際は Serial No. *Manufacturing year

注意2 : 　U S 仕向けキャビネット( G ) 組立を交換した際は Serial No. *Manufacturing year