BS en 15380-3

BRITISH STANDARD BS EN
15380-3:2006
Railway applications —
Designation system for
SUPPLIED BY BSB Edge Pvt. Ltd. UNDER THE LICENSE FROM BSI FOR RITES LTD. - GURGAON ON 13-02-2018 11:07:10 (103.7.128.130)
railway vehicles —
Part 3: Designation of installation sites
and locations
The European Standard EN 15380-3:2006 has the status of a

British Standard
ICS 01 110; 45.060.01
12&23<,1*:,7+287%6,3(50,66,21(;&(37$63(50,77('%<&23<5,*+7/$:
BS EN 15380-3:2006
National foreword
This British Standard is the official English language version of

EN 15380-3:2006.
The UK participation in its preparation was entrusted to Technical Committee
RAE/1, Railway applications, which has the responsibility to:
— aid enquirers to understand the text;
— present to the responsible international/European committee any
enquiries on the interpretation, or proposals for change, and keep UK
interests informed;
— monitor related international and European developments and
promulgate them in the UK.
A list of organizations represented on this committee can be obtained on

request to its secretary.
This standard has been produced from Part 4 of the DIN 25002 series of
standards under the CEN fast-track procedure. The UK voted against the
document in both associated ballots stating that the translation of the
documents from German to prepare the English version has resulted in a lack
of clarity as to the intent and meaning of some of the terminology used. There
is a concern that some of the railway-related terminology used does not
correspond to UK usage. Therefore, this standard should be applied with care
and consideration in order to avoid misunderstanding.
Cross-references
The British Standards which implement international or European
publications referred to in this document may be found in the BSI Catalogue
under the section entitled “International Standards Correspondence Index”, or
by using the “Search” facility of the BSI Electronic Catalogue or of British
Standards Online.
This publication does not purport to include all the necessary provisions of a
contract. Users are responsible for its correct application.
Compliance with a British Standard does not of itself confer immunity
from legal obligations.
Summary of pages
This document comprises a front cover, an inside front cover, the EN title page,
pages 2 to 12, an inside back cover and a back cover.
The BSI copyright notice displayed in this document indicates when the
document was last issued.
This British Standard was Amendments issued since publication

published under the authority
of the Standards Policy and
Strategy Committee Amd. No. Date Comments
on 31 July 2006
© BSI 2006
ISBN 0 580 48946 9

EUROPEAN STANDARD EN 15380-3
NORME EUROPÉENNE
EUROPÄISCHE NORM April 2006
ICS 01.110; 45.060.01
English Version
Railway applications - Designation system for railway vehicles -

Part 3: Designation of installation sites and locations
Applications ferroviaires - Système de classification pour Bahnanwendungen - Kennzeichnungssystematik für

véhicules ferroviaires - Partie 3: Description des positions Schienenfahrzeuge - Teil 3: Kennzeichnung von
d'installation Aufstellungs- und Einbauorten
This European Standard was approved by CEN on 6 March 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION

COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 15380-3:2006: E
worldwide for CEN national Members.
EN 15380-3:2006 (E)
Contents Page
Foreword..............................................................................................................................................................3
Introduction .........................................................................................................................................................4
1 Scope ......................................................................................................................................................4
2 Normative references ............................................................................................................................4
3 Terms and definitions ...........................................................................................................................4
4 Designation of installation sites...........................................................................................................4
4.1 General....................................................................................................................................................4
4.2 Designation set ......................................................................................................................................5
5 Designation of locations .......................................................................................................................6
5.1 General....................................................................................................................................................6
5.2 Designation set ......................................................................................................................................6
Annex A (informative) Examples of installation site and location designation ............................................9
Bibliography ......................................................................................................................................................12
List of Tables
Table 1 — Location subdivision....................................................................................................................... 8
List of Figures
Figure 1 — Designation principle..................................................................................................................... 5
Figure 2 — Example of installation site vehicle designation ........................................................................ 5
Figure 3 — Location designation principle ..................................................................................................... 6
Figure 4 — Example of a location designation ............................................................................................... 7
Figure 5 — Example of a location designation with product group and location given ............................ 7
Figure A.1 — Examples of installation site and location designation ......................................................... 9
Figure A.2 — Designation of locations on a locomotive ............................................................................. 10
Figure A.3 — Designation of locations on a 3-compartment suburban vehicle ....................................... 11
2
EN 15380-3:2006 (E)
Foreword
This document (EN 15380-3:2006) has been prepared by Technical Committee CEN/TC 256 “Railway
applications”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2006, and conflicting national standards shall be withdrawn at
the latest by October 2006.
The EN 15380 series of standards, Railway applications – Designation system for railway vehicles consists of:
 Part 1: General principles
 Part 2: Product groups
 Part 3: Designation of installation sites and locations
This European Standard is based on Part 4 of the DIN 25002 series of standards. After approval, the text of
DIN 25002-4 submitted to the PQ procedure was brought into line with the formal requirements of an EN. The
resulting editorial amendments have led to slightly modified wordings but they have no effect on the technical
content of this document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden,
Switzerland and the United Kingdom.
3
EN 15380-3:2006 (E)
Introduction
Giving the location designations is necessary in order to systematize installation planning and to provide
traceability of vehicle parts, structural units, combined assemblies and objects.
1 Scope
As a railway-specific technical standard, this document gives rules for the designation of installation sites and
locations in railway vehicles.
2 Normative references
The following referenced documents are indispensable for the application of this European Standard. For
dated references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
EN 15380-1:2006, Railway aplications — Designation system for railway vehicles — Part 1: General principles
EN 15380-2, Railway aplications — Designation system for railway vehicles — Part 2: Product groups
3 Terms and definitions

For the purposes of this document, the terms given in EN 15380-1:2006 apply.
4 Designation of installation sites
4.1 General
This designation gives information concerning the position of a unit, a vehicle or an assembly in a fixed train
configuration.
4
EN 15380-3:2006 (E)
4.2 Designation set
Figure 1 shows the layout of the designation set. It consists of the prefix signs ”++” followed by three code
letters and two code numbers for the position inside a fixed train configuration.
Key
1 Installation site prefix sign
2 Designation of railway vehicles
3 Designation of train (vehicle fleet)
4 Designation of vehicle type
5 Position within the train (only required if identical vehicles exist within a train)
Figure 1 — Designation principle
Examples of the data positions A1, A2 and A3 are given in Annex A of EN 15380-1:2006.
Figure 2 shows an example of a designation of one of several identical vehicles in a train configuration as
indicated in Figure A.1.
Key
1 Installation site prefix sign
2 "Rolling Stock" vehicle fleet
3 High-speed train
4 Centre car (vehicle type)
5 Vehicle No.02 in the train
Figure 2 — Example of installation site vehicle designation
5
EN 15380-3:2006 (E)
Annex A gives examples of the numbering system of installation sites and locations.
5 Designation of locations
5.1 General
This designation gives information concerning the location of structural units, combined assemblies and
objects in vehicles, structural units and assemblies.
5.2 Designation set
Figure 3 shows the layout of the designation set. It consists of the prefix sign "+" followed by two code letters
for the product group, two code numbers (location), a classification mark and a further possibility for
designating the location. It is not required in every case to indicate the product group. Examples are shown in
Figures 4 and 5.
Key
1 Location prefix sign

2 Product group plan according to EN 15380-2
3 Subdivision of the locations in a vehicle (see Table 1)
4 Designation of the locations in combined assemblies, structural units and objects (areas and/or co-ordinates) not
specified
Figure 3 — Location designation principle
Figure 4 shows an example of the minimum entry for a location designation
6
EN 15380-3:2006 (E)
Key

2 Pantograph
3 Location on the roof (see Table 1)
4 Location
Figure 4 — Example of a location designation
Figure 5 shows an example of a complete location designation.
Key
2 Runnig gear from EN 15380-2
3 Underframe location (see Table 1)
4 Location in running gear (W1L = wheelset shaft 1 left-hand side)
Figure 5 — Example of a location designation with product group and location given
The corresponding numbers for designating the locations are specified in Table 1.
The figures in the Annex are intended to clarify matters for different railway vehicles.
7
EN 15380-3:2006 (E)
Table 1 — Location subdivision
Main group Subdivision Name of the location

00 Roof, outside
01 to 09 Roof, outside; subdivision according to the situation
10 Driver’s cab
11 Driver’s desk
12 Cubicle in the driver’s cab, left-hand side
13 Cubicle in the driver’s cab, right-hand side
10 14 Driver’s cab, rear wall, left-hand side
15 Driver’s cab, rear wall, right-hand side
16 Driver’s cab, floor
17 Driver’s cab, ceiling
18 Vehicle head, left-hand side
19 Vehicle head, right-hand side
20 Side wall, right-hand side (with cove)
21 to 29 Subdivision according to the situation (e.g. windows)
30 Side wall, left-hand side (with cove)
31 to 39 Subdivision according to the situation
40 Interior, right-hand side
50 Interior, left-hand side
60 Interior ceiling
61 to 69 Subdivision according to the situation, e.g. intermediate ceiling
in double-decker coaches
70 Underframe (framework of a locomotive)
80 End wall, rear wall, intercommunication gangway, driver’s cab 2
of single-unit vehicles (e.g. in locomotives)
90 Reserved
8
EN 15380-3:2006 (E)
Annex A
(informative)
Examples of installation site and location designation
Figure A.1 shows the designation of the installation site and location in various trains.
The direction of travel of the vehicles is shown in acordance with EN 13775-1.
Key
1 Locomotive, 2 driver's cabs
2 Traction unit head, 1 driver's cab
3 Traction unit, 2 driver's cabs
4 Traction unit, 4-compartment
5 Suburban train, underground train
6 High-speed train (ICT)
Direction of counting
Figure A.1 — Examples of installation site and location designation
Other examples of installation site and location designation are given in Figures A.2 and A.3.
9
10
EN 15380-3:2006 (E)
Figure A.2 — Designation of locations on a locomotive
Figure A.3 — Designation of locations on a 3-compartment suburban vehicle
EN 15380-3:2006 (E)
11
EN 15380-3:2006 (E)
Bibliography
[1] EN 13775-1, Railway aplications — Measuring of new and modified freight wagons - Part 1: Measuring
principles
12
blank
BS EN
15380-3:2006
BSI — British Standards Institution
BSI is the independent national body responsible for preparing
British Standards. It presents the UK view on standards in Europe and at the
international level. It is incorporated by Royal Charter.
Revisions
British Standards are updated by amendment or revision. Users of
British Standards should make sure that they possess the latest amendments or
editions.
It is the constant aim of BSI to improve the quality of our products and services.
We would be grateful if anyone finding an inaccuracy or ambiguity while using
this British Standard would inform the Secretary of the technical committee
responsible, the identity of which can be found on the inside front cover.
Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.
BSI offers members an individual updating service called PLUS which ensures
that subscribers automatically receive the latest editions of standards.
Buying standards
Orders for all BSI, international and foreign standards publications should be
addressed to Customer Services. Tel: +44 (0)20 8996 9001.
Fax: +44 (0)20 8996 7001. Email: [email protected]. Standards are also
available from the BSI website at http://www.bsi-global.com.
In response to orders for international standards, it is BSI policy to supply the
BSI implementation of those that have been published as British Standards,
unless otherwise requested.
Information on standards
BSI provides a wide range of information on national, European and
international standards through its Library and its Technical Help to Exporters
Service. Various BSI electronic information services are also available which give
details on all its products and services. Contact the Information Centre.
Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: [email protected].
Subscribing members of BSI are kept up to date with standards developments
and receive substantial discounts on the purchase price of standards. For details
of these and other benefits contact Membership Administration.
Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001.
Email: [email protected].
Information regarding online access to British Standards via British Standards
Online can be found at http://www.bsi-global.com/bsonline.
Further information about BSI is available on the BSI website at
http://www.bsi-global.com.
Copyright
Copyright subsists in all BSI publications. BSI also holds the copyright, in the
UK, of the publications of the international standardization bodies. Except as
permitted under the Copyright, Designs and Patents Act 1988 no extract may be
reproduced, stored in a retrieval system or transmitted in any form or by any
means – electronic, photocopying, recording or otherwise – without prior written
permission from BSI.
This does not preclude the free use, in the course of implementing the standard,
of necessary details such as symbols, and size, type or grade designations. If these
details are to be used for any other purpose than implementation then the prior
BSI written permission of BSI must be obtained.
389 Chiswick High Road Details and advice can be obtained from the Copyright & Licensing Manager.
London Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553.
Email: [email protected].
W4 4AL

BS en 15380-3

Uploaded by

Copyright:

Available Formats

BS en 15380-3

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

BS en 15380-3

Uploaded by

Copyright:

Available Formats

BRITISH STANDARD BS EN

The European Standard EN 15380-3:2006 has the status of a

ICS 01 110; 45.060.01

This British Standard is the official English language version of

— aid enquirers to understand the text;

A list of organizations represented on this committee can be obtained on

This British Standard was Amendments issued since publication

ISBN 0 580 48946 9

ICS 01.110; 45.060.01

Railway applications - Designation system for railway vehicles -

Applications ferroviaires - Système de classification pour Bahnanwendungen - Kennzeichnungssystematik für

This European Standard was approved by CEN on 6 March 2006.

EUROPEAN COMMITTEE FOR STANDARDIZATION

Management Centre: rue de Stassart, 36 B-1050 Brussels

Table 1 — Location subdivision....................................................................................................................... 8

Figure 1 — Designation principle..................................................................................................................... 5

Figure 2 — Example of installation site vehicle designation ........................................................................ 5

Figure 3 — Location designation principle ..................................................................................................... 6

Figure 4 — Example of a location designation ............................................................................................... 7

Figure A.1 — Examples of installation site and location designation ......................................................... 9

Figure A.2 — Designation of locations on a locomotive ............................................................................. 10

Figure A.3 — Designation of locations on a 3-compartment suburban vehicle ....................................... 11

 Part 1: General principles

 Part 2: Product groups

 Part 3: Designation of installation sites and locations

3 Terms and definitions

4 Designation of installation sites

4.2 Designation set

Figure 1 — Designation principle

Figure 2 — Example of installation site vehicle designation

5.2 Designation set

1 Location prefix sign

Figure 3 — Location designation principle

Figure 4 shows an example of the minimum entry for a location designation

1 Location prefix sign

Figure 4 — Example of a location designation

Figure 5 shows an example of a complete location designation.

Table 1 — Location subdivision

Main group Subdivision Name of the location

Examples of installation site and location designation

The direction of travel of the vehicles is shown in acordance with EN 13775-1.

Figure A.1 — Examples of installation site and location designation

Figure A.2 — Designation of locations on a locomotive

You might also like