R2A LM4040-n V-Ref
R2A LM4040-n V-Ref
LM4040-N, LM4040-N-Q1
SNOS633K – OCTOBER 2000 – REVISED JUNE 2016
RS VOUT
Cathode
LM4040
Anode
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM4040-N, LM4040-N-Q1
SNOS633K – OCTOBER 2000 – REVISED JUNE 2016 www.ti.com
Table of Contents
1 Features .................................................................. 1 6.17 Electrical Characteristics: 5-V LM4040-N VR
Tolerance Grades 'C' And 'D'; Temperature Grade
2 Applications ........................................................... 1
'I'............................................................................... 24
3 Description ............................................................. 1 6.18 Electrical Characteristics: 5-V LM4040-N VR
4 Revision History..................................................... 3 Tolerance Grades 'C' And 'D'; Temperature Grade
5 Pin Configuration and Functions ......................... 4 'E' ............................................................................. 26
6 Specifications......................................................... 5 6.19 Electrical Characteristics: 8.2-V LM4040-N VR
Tolerance Grades 'A' And 'B'; Temperature Grade
6.1 Absolute Maximum Ratings ...................................... 5 'I'............................................................................... 27
6.2 ESD Ratings.............................................................. 5 6.20 Electrical Characteristics: 8.2-V Lm4040-N VR
6.3 Recommended Operating Conditions....................... 6 Tolerance Grades 'C' And 'D'; Temperature Grade
6.4 Thermal Information .................................................. 6 'I'............................................................................... 28
6.5 Electrical Characteristics: 2-V LM4040-N VR 6.21 Electrical Characteristics: 10-V LM4040-N VR
Tolerance Grades 'A' And 'B'; Temperature Grade 'I' 7 Tolerance Grades 'A' And 'B'; Temperature Grade
6.6 Electrical Characteristics: 2-V LM4040-N VR 'I'............................................................................... 29
Tolerance Grades 'C', 'D', And 'E'; Temperature 6.22 Electrical Characteristics: 10-V LM4040-N VR
Grade 'I'...................................................................... 8 Tolerance Grades 'C' And 'D'; Temperature Grade
6.7 Electrical Characteristics: 2-V LM4040-N VR 'I'............................................................................... 30
Tolerance Grades 'C', 'D', And 'E'; Temperature 6.23 Typical Characteristics .......................................... 31
Grade 'E' .................................................................. 10 7 Parameter Measurement Information ................ 32
6.8 Electrical Characteristics: 2.5-V LM4040-N VR 8 Detailed Description ............................................ 33
Tolerance Grades 'A' And 'B'; Temperature Grade 'I'
(AEC Grade 3) ......................................................... 11 8.1 Overview ................................................................. 33
6.9 Electrical Characteristics: 2.5-V LM4040-N VR 8.2 Functional Block Diagram ....................................... 33
Tolerance Grades 'C', 'D', and 'E'; Temperature Grade 8.3 Feature Description................................................. 33
'I' (AEC Grade 3)...................................................... 13 8.4 Device Functional Modes........................................ 33
6.10 Electrical Characteristics: 2.5-V LM4040-N VR 9 Application and Implementation ........................ 34
Tolerance Grades 'C', 'D', And 'E'; Temperature 9.1 Application Information............................................ 34
Grade 'E' (AEC Grade 1) ......................................... 15
9.2 Typical Applications ................................................ 34
6.11 Electrical Characteristics: 3-V LM4040-N VR
Tolerance Grades 'A' And 'B'; Temperature Grade 10 Power Supply Recommendations ..................... 41
'I'............................................................................... 17 11 Layout................................................................... 41
6.12 Electrical Characteristics: 3-V LM4040-N VR 11.1 Layout Guidelines ................................................. 41
Tolerance Grades 'C', 'D', And 'E'; Temperature 11.2 Layout Example .................................................... 41
Grade 'I'.................................................................... 18
12 Device and Documentation Support ................. 42
6.13 Electrical Characteristics: 3-V LM4040-N VR
Tolerance Grades 'C', 'D', And 'E'; Temperature 12.1 Documentation Support ........................................ 42
Grade 'E' .................................................................. 20 12.2 Related Links ........................................................ 42
6.14 Electrical Characteristics: 4.1-V LM4040-N VR 12.3 Community Resources.......................................... 42
Tolerance Grades 'A' And 'B'; Temperature Grade 12.4 Trademarks ........................................................... 42
'I'............................................................................... 21
12.5 Electrostatic Discharge Caution ............................ 42
6.15 Electrical Characteristics: 4.1-V LM4040-N VR
12.6 Glossary ................................................................ 42
Tolerance Grades 'C' and 'D'; Temperature Grade
'I'............................................................................... 22 13 Mechanical, Packaging, And Orderable
6.16 Electrical Characteristics: 5-V LM4040-N VR Information ........................................................... 42
Tolerance Grades 'A' And 'B'; Temperature Grade 13.1 SOT-23 and SC70 Package Marking Information 42
'I'............................................................................... 23
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
• Added ESD Ratings table, Feature Description section, Device Functional Modes section, Application and
Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation
Support section, and Mechanical, Packaging, and Orderable Information section ............................................................... 1
• Added some of the latest inclusions from new TI formatting and made available of the automotive grade for the
SOT-23 package..................................................................................................................................................................... 1
DBZ Package
3-Pin SOT-23 LP Package
Top View 3-Pin TO-92
Bottom View
1 NC + ±
+
3(1)
2
±
DCK Package
5-Pin SC70
Top View
1 5
± NC
2
NC(2)
3 4
+ NC
Pin Functions
PIN
I/O DESCRIPTION
NAME SOT-23 TO-92 SC70
Anode 2 1 1 O Anode pin, normally grounded
Cathode 1 2 3 I/O Shunt Current/Output Voltage
(1) (2)
NC 3 — 2 — Must float or connect to anode
NC — 3 4, 5 — No connect
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1) (2)
MIN MAX UNIT
Reverse current 20 mA
Forward current 10 mA
SOT-23 (M3) package 306 mW
Power dissipation (TA =
TO-92 (Z) package 550 mW
25°C) (3)
SC70 (M7) package 241 mW
SOT-23 (M3) Package Peak Reflow (30 sec) 260 °C
Soldering temperature (4)
TO-92 (Z) Package Soldering (10 sec) 260 °C
SC70 (M7) Package Peak Reflow (30 sec) 260 °C
Storage temperature –65 150 °C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
(3) The maximum power dissipation must be derated at elevated temperatures and is dictated by TJmax (maximum junction temperature),
RθJA (junction to ambient thermal resistance), and TA (ambient temperature). The maximum allowable power dissipation at any
temperature is PDmax = (TJmax − TA)/RθJA or the number given in the Absolute Maximum Ratings, whichever is lower. For the LM4040-N,
TJmax = 125°C, and the typical thermal resistance (RθJA), when board mounted, is 326°C/W for the SOT-23 package, and 180°C/W with
0.4″ lead length and 170°C/W with 0.125″ lead length for the TO-92 package and 415°C/W for the SC70 Package.
(4) For definitions of Peak Reflow Temperatures for Surface Mount devices, see the TI Absolute Maximum Ratings for Soldering Application
Report (SNOA549).
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Recommended Operating Conditions indicate
conditions for which the device is functional, but do not ensure specific performance limits. For ensured specifications and test
conditions, see the Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance
characteristics may degrade when the device is not operated under the listed test conditions.
(2) The maximum power dissipation must be derated at elevated temperatures and is dictated by TJmax (maximum junction temperature),
RθJA (junction to ambient thermal resistance), and TA (ambient temperature). The maximum allowable power dissipation at any
temperature is PDmax = (TJmax − TA)/RθJA or the number given in the Absolute Maximum Ratings, whichever is lower. For the LM4040-N,
TJmax = 125°C, and the typical thermal resistance (RθJA), when board mounted, is 326°C/W for the SOT-23 package, and 180°C/W with
0.4″ lead length and 170°C/W with 0.125″ lead length for the TO-92 package and 415°C/W for the SC70 package.
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
6.5 Electrical Characteristics: 2-V LM4040-N VR Tolerance Grades 'A' And 'B'; Temperature
Grade 'I'
all other limits TA = TJ = 25°C. The grades A and B designate initial Reverse Breakdown Voltage tolerances of ±0.1% and
±0.2%, respectively.
PARAMETER TEST CONDITIONS MIN (1) TYP MAX (1) UNIT
Reverse Breakdown
IR = 100 μA 2.048 V
Voltage
LM4040AIM3
±2
LM4040AIZ
LM4040BIM3 mV
LM4040BIZ ±4.1
VR
Reverse Breakdown LM4040BIM7
IR = 100 μA
Voltage Tolerance (2) LM4040AIM3 TA = TJ = TMIN to
±15
LM4040AIZ TMAX
LM4040BIM3 mV
TA = TJ = TMIN to
LM4040BIZ ±17
TMAX
LM4040BIM7
(1) Limits are 100% production tested at 25°C. Limits over temperature are ensured through correlation using Statistical Quality Control
(SQC) methods. The limits are used to calculate AOQL.
(2) The overtemperature limit for Reverse Breakdown Voltage Tolerance is defined as the room temperature Reverse Breakdown Voltage
Tolerance ±[(ΔVR/ΔT)(maxΔT)(VR)]. Where, ΔVR/ΔT is the VR temperature coefficient, maxΔT is the maximum difference in temperature
from the reference point of 25°C to T MIN or TMAX, and VR is the reverse breakdown voltage. The total overtemperature tolerance for the
different grades in the industrial temperature range where maxΔT = 65°C is shown below:
A-grade: ±0.75% = ±0.1% ±100 ppm/°C × 65°C
B-grade: ±0.85% = ±0.2% ±100 ppm/°C × 65°C
C-grade: ±1.15% = ±0.5% ±100 ppm/°C × 65°C
D-grade: ±1.98% = ±1.0% ±150 ppm/°C × 65°C
E-grade: ±2.98% = ±2.0% ±150 ppm/°C × 65°C
The total overtemperature tolerance for the different grades in the extended temperature range where max ΔT = 100 °C is shown below:
C-grade: ±1.5% = ±0.5% ±100 ppm/°C × 100°C
D-grade: ±2.5% = ±1.0% ±150 ppm/°C × 100°C
E-grade: ±3.5% = ±2.0% ±150 ppm/°C × 100°C
Therefore, as an example, the A-grade 2.5-V LM4040-N has an overtemperature Reverse Breakdown Voltage tolerance of ±2.5 V ×
0.75% = ±19 mV.
(3) Load regulation is measured on pulse basis from no load to the specified load current. Output changes due to die temperature change
must be taken into account separately.
(4) Thermal hysteresis is defined as the difference in voltage measured at 25°C after cycling to temperature -40°C and the 25°C
measurement after cycling to temperature 125°C.
6.6 Electrical Characteristics: 2-V LM4040-N VR Tolerance Grades 'C', 'D', And 'E'; Temperature
Grade 'I'
all other limits TA = TJ = 25°C. The grades C, D and E designate initial Reverse Breakdown Voltage tolerances of ±0.5%, ±1%
and ±2%, respectively.
PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
Reverse Breakdown
IR = 100 μA 2.048 V
Voltage
LM4040CIM3 TA = TJ = 25°C ±10
LM4040CIZ
LM4040CIM7 TA = TJ = TMIN to TMAX ±23
VR
Reverse Breakdown LM4040DIM3 TA = TJ = 25°C ±20
I = 100 μA LM4040DIZ mV
Voltage Tolerance (3) R
LM4040DIM7 TA = TJ = TMIN to TMAX ±40
LM4040EIZ TA = TJ = 25°C 45 65
LM4040EIM7 TA = TJ = TMIN to TMAX 70
IR = 10 mA ±20
LM4040CIM3 TA = TJ = 25°C ±15
LM4040CIZ
LM4040CIM7 TA = TJ = TMIN to TMAX ±100
Average Reverse
Breakdown Voltage LM4040DIM3 TA = TJ = 25°C ±15
ΔVR/ΔT IR = 1 mA LM4040DIZ ppm/°C
Temperature
LM4040DIM7 TA = TJ = TMIN to TMAX ±150
Coefficient (3)
LM4040EIZ TA = TJ = 25°C ±15
LM4040EIM7 TA = TJ = TMIN to TMAX ±150
IR = 100 μA ±15
(1) Limits are 100% production tested at 25°C. Limits over temperature are ensured through correlation using Statistical Quality Control
(SQC) methods. The limits are used to calculate AOQL.
(2) Typicals are at TJ = 25°C and represent most likely parametric norm.
(3) The overtemperature limit for Reverse Breakdown Voltage Tolerance is defined as the room temperature Reverse Breakdown Voltage
Tolerance ±[(ΔVR/ΔT)(maxΔT)(VR)]. Where, ΔVR/ΔT is the VR temperature coefficient, maxΔT is the maximum difference in temperature
from the reference point of 25°C to T MIN or TMAX, and VR is the reverse breakdown voltage. The total overtemperature tolerance for the
different grades in the industrial temperature range where maxΔT = 65°C is shown below:
A-grade: ±0.75% = ±0.1% ±100 ppm/°C × 65°C
B-grade: ±0.85% = ±0.2% ±100 ppm/°C × 65°C
C-grade: ±1.15% = ±0.5% ±100 ppm/°C × 65°C
D-grade: ±1.98% = ±1.0% ±150 ppm/°C × 65°C
E-grade: ±2.98% = ±2.0% ±150 ppm/°C × 65°C
The total overtemperature tolerance for the different grades in the extended temperature range where max ΔT = 100 °C is shown below:
C-grade: ±1.5% = ±0.5% ±100 ppm/°C × 100°C
D-grade: ±2.5% = ±1.0% ±150 ppm/°C × 100°C
E-grade: ±3.5% = ±2.0% ±150 ppm/°C × 100°C
Therefore, as an example, the A-grade 2.5-V LM4040-N has an overtemperature Reverse Breakdown Voltage tolerance of ±2.5V ×
0.75% = ±19 mV.
8 Submit Documentation Feedback Copyright © 2000–2016, Texas Instruments Incorporated
Electrical Characteristics: 2-V LM4040-N VR Tolerance Grades 'C', 'D', And 'E'; Temperature
Grade 'I' (continued)
all other limits TA = TJ = 25°C. The grades C, D and E designate initial Reverse Breakdown Voltage tolerances of ±0.5%, ±1%
and ±2%, respectively.
PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
LM4040CIM3 TA = TJ = 25°C 0.3 0.8
LM4040CIZ
LM4040CIM7 TA = TJ = TMIN to TMAX 1
(4) Load regulation is measured on pulse basis from no load to the specified load current. Output changes due to die temperature change
must be taken into account separately.
(5) Thermal hysteresis is defined as the difference in voltage measured at 25°C after cycling to temperature –40°C and the 25°C
measurement after cycling to temperature 125°C.
6.7 Electrical Characteristics: 2-V LM4040-N VR Tolerance Grades 'C', 'D', And 'E'; Temperature
Grade 'E'
all other limits TA = TJ = 25°C. The grades C, D and E designate initial Reverse Breakdown Voltage tolerances of ±0.5%, ±1%
and ±2%, respectively.
PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
Reverse Breakdown
IR = 100 μA 2.048 V
Voltage
TA = TJ = 25°C ±10
LM4040CEM3
TA = TJ = TMIN to TMAX ±30
VR
Reverse Breakdown TA = TJ = 25°C ±20
IR = 100 μA LM4040DEM3 mV
Voltage Tolerance (3) TA = TJ = TMIN to TMAX ±50
TA = TJ = 25°C ±41
LM4040EEM3
TA = TJ = TMIN to TMAX ±70
TA = TJ = 25°C 45 60
LM4040CEM3
TA = TJ = TMIN to TMAX 68
(1) Limits are 100% production tested at 25°C. Limits over temperature are ensured through correlation using Statistical Quality Control
(SQC) methods. The limits are used to calculate AOQL.
(2) Typicals are at TJ = 25°C and represent most likely parametric norm.
(3) The overtemperature limit for Reverse Breakdown Voltage Tolerance is defined as the room temperature Reverse Breakdown Voltage
Tolerance ±[(ΔVR/ΔT)(maxΔT)(VR)]. Where, ΔVR/ΔT is the VR temperature coefficient, maxΔT is the maximum difference in temperature
from the reference point of 25°C to T MIN or TMAX, and VR is the reverse breakdown voltage. The total overtemperature tolerance for the
different grades in the industrial temperature range where maxΔT = 65°C is shown below:
A-grade: ±0.75% = ±0.1% ±100 ppm/°C × 65°C
B-grade: ±0.85% = ±0.2% ±100 ppm/°C × 65°C
C-grade: ±1.15% = ±0.5% ±100 ppm/°C × 65°C
D-grade: ±1.98% = ±1.0% ±150 ppm/°C × 65°C
E-grade: ±2.98% = ±2.0% ±150 ppm/°C × 65°C
The total overtemperature tolerance for the different grades in the extended temperature range where max ΔT = 100 °C is shown below:
C-grade: ±1.5% = ±0.5% ±100 ppm/°C × 100°C
D-grade: ±2.5% = ±1.0% ±150 ppm/°C × 100°C
E-grade: ±3.5% = ±2.0% ±150 ppm/°C × 100°C
Therefore, as an example, the A-grade 2.5-V LM4040-N has an overtemperature Reverse Breakdown Voltage tolerance of ±2.5V ×
0.75% = ±19 mV.
(4) Load regulation is measured on pulse basis from no load to the specified load current. Output changes due to die temperature change
must be taken into account separately.
10 Submit Documentation Feedback Copyright © 2000–2016, Texas Instruments Incorporated
Electrical Characteristics: 2-V LM4040-N VR Tolerance Grades 'C', 'D', And 'E'; Temperature
Grade 'E' (continued)
all other limits TA = TJ = 25°C. The grades C, D and E designate initial Reverse Breakdown Voltage tolerances of ±0.5%, ±1%
and ±2%, respectively.
PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
LM4040CEM3 0.3 0.9
Reverse Dynamic IR = 1 mA, f = 120 Hz,
ZR LM4040DEM3 0.3 1.1 Ω
Impedance IAC = 0.1 IR
LM4040EEM3 0.3 1.1
IR = 100 μA
eN Wideband Noise 35 μVrms
10 Hz ≤ f ≤ 10 kHz
Reverse Breakdown t = 1000 hrs
ΔVR Voltage Long Term T = 25°C ±0.1°C 120 ppm
Stability IR = 100 μA
Thermal
VHYST ΔT = −40°C to 125°C 0.08%
Hysteresis (5)
(5) Thermal hysteresis is defined as the difference in voltage measured at 25°C after cycling to temperature –40°C and the 25°C
measurement after cycling to temperature 125°C.
6.8 Electrical Characteristics: 2.5-V LM4040-N VR Tolerance Grades 'A' And 'B'; Temperature
Grade 'I' (AEC Grade 3)
all other limits TA = TJ = 25°C. The grades A and B designate initial Reverse Breakdown Voltage tolerances of ±0.1% and
±0.2%, respectively.
PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
Reverse Breakdown
IR = 100 μA 2.5 V
Voltage
LM4040AIM3 TA = TJ = 25°C ±2.5
LM4040AIZ
VR LM4040AIM3 TA = TJ = TMIN to TMAX ±19
Reverse Breakdown
IR = 100 μA LM4040BIM3 TA = TJ = 25°C ±5 mV
Voltage Tolerance (3)
LM4040BIZ
LM4040BIM7 TA = TJ = TMIN to TMAX ±21
LM4040QBIM3
(1) Limits are 100% production tested at 25°C. Limits over temperature are ensured through correlation using Statistical Quality Control
(SQC) methods. The limits are used to calculate AOQL.
(2) Typicals are at TJ = 25°C and represent most likely parametric norm.
(3) The overtemperature limit for Reverse Breakdown Voltage Tolerance is defined as the room temperature Reverse Breakdown Voltage
Tolerance ±[(ΔVR/ΔT)(maxΔT)(VR)]. Where, ΔVR/ΔT is the VR temperature coefficient, maxΔT is the maximum difference in temperature
from the reference point of 25°C to T MIN or TMAX, and VR is the reverse breakdown voltage. The total overtemperature tolerance for the
different grades in the industrial temperature range where maxΔT = 65°C is shown below:
A-grade: ±0.75% = ±0.1% ±100 ppm/°C × 65°C
B-grade: ±0.85% = ±0.2% ±100 ppm/°C × 65°C
C-grade: ±1.15% = ±0.5% ±100 ppm/°C × 65°C
D-grade: ±1.98% = ±1.0% ±150 ppm/°C × 65°C
E-grade: ±2.98% = ±2.0% ±150 ppm/°C × 65°C
The total overtemperature tolerance for the different grades in the extended temperature range where max ΔT = 100 °C is shown below:
C-grade: ±1.5% = ±0.5% ±100 ppm/°C × 100°C
D-grade: ±2.5% = ±1.0% ±150 ppm/°C × 100°C
E-grade: ±3.5% = ±2.0% ±150 ppm/°C × 100°C
Therefore, as an example, the A-grade 2.5-V LM4040-N has an overtemperature Reverse Breakdown Voltage tolerance of ±2.5V ×
0.75% = ±19 mV.
Copyright © 2000–2016, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: LM4040-N LM4040-N-Q1
LM4040-N, LM4040-N-Q1
SNOS633K – OCTOBER 2000 – REVISED JUNE 2016 www.ti.com
Electrical Characteristics: 2.5-V LM4040-N VR Tolerance Grades 'A' And 'B'; Temperature Grade
'I' (AEC Grade 3) (continued)
all other limits TA = TJ = 25°C. The grades A and B designate initial Reverse Breakdown Voltage tolerances of ±0.1% and
±0.2%, respectively.
PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
TA = TJ = 25°C 0.3 0.8
Reverse Breakdown IRMIN ≤ IR ≤ 1 mA
ΔVR/ΔI Voltage Change with TA = TJ = TMIN to TMAX 1
mV
R Operating Current TA = TJ = 25°C 2.5 6
Change (4) 1 mA ≤ IR ≤ 15 mA
TA = TJ = TMIN to TMAX 8
Reverse Dynamic IR = 1 mA, f = 120 Hz,
ZR 0.3 0.8 Ω
Impedance IAC = 0.1 IR
IR = 100 μA
eN Wideband Noise 35 μVrms
10 Hz ≤ f ≤ 10 kHz
Reverse Breakdown t = 1000 hrs
ΔVR Voltage Long Term T = 25°C ±0.1°C 120 ppm
Stability IR = 100 μA
VHYST Thermal Hysteresis (5) ΔT = −40°C to 125°C 0.08%
(4) Load regulation is measured on pulse basis from no load to the specified load current. Output changes due to die temperature change
must be taken into account separately.
(5) Thermal hysteresis is defined as the difference in voltage measured at 25°C after cycling to temperature –40°C and the 25°C
measurement after cycling to temperature 125°C.
6.9 Electrical Characteristics: 2.5-V LM4040-N VR Tolerance Grades 'C', 'D', and 'E';
Temperature Grade 'I' (AEC Grade 3)
all other limits TA = TJ = 25°C. The grades C, D and E designate initial Reverse Breakdown Voltage tolerances of ±0.5%, ±1%
and ±2%, respectively.
PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
Reverse Breakdown
IR = 100 μA 2.5 V
Voltage
LM4040CIZ TA = TJ = 25°C ±12
LM4040CIM3
LM4040CIM7 TA = TJ = TMIN to TMAX ±29
LM4040QCIM3
(1) Limits are 100% production tested at 25°C. Limits over temperature are ensured through correlation using Statistical Quality Control
(SQC) methods. The limits are used to calculate AOQL.
(2) Typicals are at TJ = 25°C and represent most likely parametric norm.
(3) The overtemperature limit for Reverse Breakdown Voltage Tolerance is defined as the room temperature Reverse Breakdown Voltage
Tolerance ±[(ΔVR/ΔT)(maxΔT)(VR)]. Where, ΔVR/ΔT is the VR temperature coefficient, maxΔT is the maximum difference in temperature
from the reference point of 25°C to T MIN or TMAX, and VR is the reverse breakdown voltage. The total overtemperature tolerance for the
different grades in the industrial temperature range where maxΔT = 65°C is shown below:
A-grade: ±0.75% = ±0.1% ±100 ppm/°C × 65°C
B-grade: ±0.85% = ±0.2% ±100 ppm/°C × 65°C
C-grade: ±1.15% = ±0.5% ±100 ppm/°C × 65°C
D-grade: ±1.98% = ±1.0% ±150 ppm/°C × 65°C
E-grade: ±2.98% = ±2.0% ±150 ppm/°C × 65°C
The total overtemperature tolerance for the different grades in the extended temperature range where max ΔT = 100 °C is shown below:
C-grade: ±1.5% = ±0.5% ±100 ppm/°C × 100°C
D-grade: ±2.5% = ±1.0% ±150 ppm/°C × 100°C
E-grade: ±3.5% = ±2.0% ±150 ppm/°C × 100°C
Therefore, as an example, the A-grade 2.5-V LM4040-N has an overtemperature Reverse Breakdown Voltage tolerance of ±2.5V ×
0.75% = ±19 mV.
Copyright © 2000–2016, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: LM4040-N LM4040-N-Q1
LM4040-N, LM4040-N-Q1
SNOS633K – OCTOBER 2000 – REVISED JUNE 2016 www.ti.com
Electrical Characteristics: 2.5-V LM4040-N VR Tolerance Grades 'C', 'D', and 'E'; Temperature
Grade 'I' (AEC Grade 3) (continued)
all other limits TA = TJ = 25°C. The grades C, D and E designate initial Reverse Breakdown Voltage tolerances of ±0.5%, ±1%
and ±2%, respectively.
PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
LM4040CIZ TA = TJ = 25°C 0.3 0.8
LM4040CIM3
LM4040CIM7 TA = TJ = TMIN to TMAX 1
LM4040QCIM3
LM4040DIZ TA = TJ = 25°C 0.3 1
LM4040DIM3
IRMIN ≤ IR ≤ 1 mA
LM4040DIM7 TA = TJ = TMIN to TMAX 1.2
LM4040QDIM3
LM4040EIZ TA = TJ = 25°C 0.3 1
LM4040EIM3
Reverse Breakdown LM4040EIM7 TA = TJ = TMIN to TMAX 1.2
ΔVR/ΔI Voltage Change with LM4040QEIM3
mV
R Operating Current LM4040CIZ TA = TJ = 25°C 2.5 6
Change (4) LM4040CIM3
LM4040CIM7 TA = TJ = TMIN to TMAX 8
LM4040QCIM3
LM4040DIZ TA = TJ = 25°C 2.5 8
LM4040DIM3
1 mA ≤ IR ≤ 15 mA
LM4040DIM7 TA = TJ = TMIN to TMAX 10
LM4040QDIM3
LM4040EIZ TA = TJ = 25°C 2.5 8
LM4040EIM3
LM4040EIM7 TA = TJ = TMIN to TMAX 10
LM4040QEIM3
LM4040CIZ
LM4040CIM3
0.3 0.9
LM4040CIM7
LM4040QCIM3
LM4040DIZ
Reverse Dynamic IR = 1 mA, f = 120 Hz LM4040DIM3
ZR 0.3 1.1 Ω
Impedance IAC = 0.1 IR LM4040DIM7
LM4040QDIM3
LM4040EIZ
LM4040EIM3
0.3 1.1
LM4040EIM7
LM4040QEIM3
IR = 100 μA
eN Wideband Noise 35 μVrms
10 Hz ≤ f ≤ 10 kHz
Reverse Breakdown t = 1000 hrs
ΔVR Voltage Long Term T = 25°C ±0.1°C 120 ppm
Stability IR = 100 μA
Thermal
VHYST ΔT= −40°C to 125°C 0.08%
Hysteresis (5)
(4) Load regulation is measured on pulse basis from no load to the specified load current. Output changes due to die temperature change
must be taken into account separately.
(5) Thermal hysteresis is defined as the difference in voltage measured at 25°C after cycling to temperature –40°C and the 25°C
measurement after cycling to temperature 125°C.
6.10 Electrical Characteristics: 2.5-V LM4040-N VR Tolerance Grades 'C', 'D', And 'E';
Temperature Grade 'E' (AEC Grade 1)
all other limits TA = TJ = 25°C. The grades C, D and E designate initial Reverse Breakdown Voltage tolerances of ±0.5%, ±1%
and ±2%, respectively.
PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
Reverse Breakdown
IR = 100 μA 2.5 V
Voltage
LM4040CEM3 TA = TJ = 25°C 45 60
LM4040QCEM3 TA = TJ = TMIN to TMAX 68
LM4040EEM3 TA = TJ = 25°C 45 65
LM4040QEEM3 TA = TJ = TMIN to TMAX 73
Average Reverse IR = 10 mA ±20
Breakdown Voltage
LM4040CEM3 TA = TJ = 25°C ±15
Temperature
LM4040QCEM3
Coefficient (3) TA = TJ = TMIN to TMAX ±100
LM4040DEM3 TA = TJ = 25°C ±15
ΔVR/ΔT IR = 1 mA LM4040QDEM3 ppm/°C
TA = TJ = TMIN to TMAX ±150
LM4040EEM3 TA = TJ = 25°C ±15
LM4040QEEM3
TA = TJ = TMIN to TMAX ±150
IR = 100 μA ±15
(1) Limits are 100% production tested at 25°C. Limits over temperature are ensured through correlation using Statistical Quality Control
(SQC) methods. The limits are used to calculate AOQL.
(2) Typicals are at TJ = 25°C and represent most likely parametric norm.
(3) The overtemperature limit for Reverse Breakdown Voltage Tolerance is defined as the room temperature Reverse Breakdown Voltage
Tolerance ±[(ΔVR/ΔT)(maxΔT)(VR)]. Where, ΔVR/ΔT is the VR temperature coefficient, maxΔT is the maximum difference in temperature
from the reference point of 25°C to T MIN or TMAX, and VR is the reverse breakdown voltage. The total overtemperature tolerance for the
different grades in the industrial temperature range where maxΔT = 65°C is shown below:
A-grade: ±0.75% = ±0.1% ±100 ppm/°C × 65°C
B-grade: ±0.85% = ±0.2% ±100 ppm/°C × 65°C
C-grade: ±1.15% = ±0.5% ±100 ppm/°C × 65°C
D-grade: ±1.98% = ±1.0% ±150 ppm/°C × 65°C
E-grade: ±2.98% = ±2.0% ±150 ppm/°C × 65°C
The total overtemperature tolerance for the different grades in the extended temperature range where max ΔT = 100 °C is shown below:
C-grade: ±1.5% = ±0.5% ±100 ppm/°C × 100°C
D-grade: ±2.5% = ±1.0% ±150 ppm/°C × 100°C
E-grade: ±3.5% = ±2.0% ±150 ppm/°C × 100°C
Therefore, as an example, the A-grade 2.5-V LM4040-N has an overtemperature Reverse Breakdown Voltage tolerance of ±2.5V ×
0.75% = ±19 mV.
(4) Load regulation is measured on pulse basis from no load to the specified load current. Output changes due to die temperature change
must be taken into account separately.
Copyright © 2000–2016, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Links: LM4040-N LM4040-N-Q1
LM4040-N, LM4040-N-Q1
SNOS633K – OCTOBER 2000 – REVISED JUNE 2016 www.ti.com
Electrical Characteristics: 2.5-V LM4040-N VR Tolerance Grades 'C', 'D', And 'E'; Temperature
Grade 'E' (AEC Grade 1) (continued)
all other limits TA = TJ = 25°C. The grades C, D and E designate initial Reverse Breakdown Voltage tolerances of ±0.5%, ±1%
and ±2%, respectively.
PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
LM4040CEM3
0.3 0.9
LM4040QCEM3
Reverse Dynamic IR = 1 mA, f = 120 Hz, LM4040DEM3
ZR 0.3 1.1 Ω
Impedance IAC = 0.1 IR LM4040QDEM3
LM4040EEM3
0.3 1.1
LM4040QEEM3
IR = 100 μA
eN Wideband Noise 35 μVrms
10 Hz ≤ f ≤ 10 kHz
Reverse Breakdown t = 1000 hrs
ΔVR Voltage Long Term T = 25°C ±0.1°C 120 ppm
Stability IR = 100 μA
Thermal
VHYST ΔT= −40°C to 125°C 0.08%
Hysteresis (5)
(5) Thermal hysteresis is defined as the difference in voltage measured at +25°C after cycling to temperature -40°C and the 25°C
measurement after cycling to temperature 125°C.
6.11 Electrical Characteristics: 3-V LM4040-N VR Tolerance Grades 'A' And 'B'; Temperature
Grade 'I'
all other limits TA = TJ = 25°C. The grades A and B designate initial Reverse Breakdown Voltage tolerances of ±0.1% and
±0.2%, respectively.
PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
Reverse Breakdown
IR = 100 μA 3 V
Voltage
LM4040AIM3 TA = TJ = 25°C ±3
VR LM4040AIZ TA = TJ = TMIN to TMAX ±22
Reverse Breakdown
IR = 100 μA mV
Voltage Tolerance (3) LM4040BIM3 TA = TJ = 25°C ±6
LM4040BIZ
LM4040BIM7 TA = TJ = TMIN to TMAX ±26
(1) Limits are 100% production tested at 25°C. Limits over temperature are ensured through correlation using Statistical Quality Control
(SQC) methods. The limits are used to calculate AOQL.
(2) Typicals are at TJ = 25°C and represent most likely parametric norm.
(3) The overtemperature limit for Reverse Breakdown Voltage Tolerance is defined as the room temperature Reverse Breakdown Voltage
Tolerance ±[(ΔVR/ΔT)(maxΔT)(VR)]. Where, ΔVR/ΔT is the VR temperature coefficient, maxΔT is the maximum difference in temperature
from the reference point of 25°C to T MIN or TMAX, and VR is the reverse breakdown voltage. The total overtemperature tolerance for the
different grades in the industrial temperature range where maxΔT = 65°C is shown below:
A-grade: ±0.75% = ±0.1% ±100 ppm/°C × 65°C
B-grade: ±0.85% = ±0.2% ±100 ppm/°C × 65°C
C-grade: ±1.15% = ±0.5% ±100 ppm/°C × 65°C
D-grade: ±1.98% = ±1.0% ±150 ppm/°C × 65°C
E-grade: ±2.98% = ±2.0% ±150 ppm/°C × 65°C
The total overtemperature tolerance for the different grades in the extended temperature range where max ΔT = 100 °C is shown below:
C-grade: ±1.5% = ±0.5% ±100 ppm/°C × 100°C
D-grade: ±2.5% = ±1.0% ±150 ppm/°C × 100°C
E-grade: ±3.5% = ±2.0% ±150 ppm/°C × 100°C
Therefore, as an example, the A-grade 2.5-V LM4040-N has an overtemperature Reverse Breakdown Voltage tolerance of ±2.5V ×
0.75% = ±19 mV.
(4) Load regulation is measured on pulse basis from no load to the specified load current. Output changes due to die temperature change
must be taken into account separately.
(5) Thermal hysteresis is defined as the difference in voltage measured at +25°C after cycling to temperature -40°C and the 25°C
measurement after cycling to temperature 125°C.
6.12 Electrical Characteristics: 3-V LM4040-N VR Tolerance Grades 'C', 'D', And 'E';
Temperature Grade 'I'
all other limits TA = TJ = 25°C. The grades C, D and E designate initial Reverse Breakdown Voltage tolerances of ±0.5%, ±1%
and ±2%, respectively.
PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
Reverse Breakdown IR = 100 μA 3 V
Voltage
LM4040CIM3 TA = TJ = 25°C ±15
LM4040CIZ
LM4040CIM7 TA = TJ = TMIN to TMAX ±34
VR
Reverse Breakdown LM4040DIM3 TA = TJ = 25°C ±30
I = 100 μA LM4040DIZ mV
Voltage Tolerance (3) R
LM4040DIM7 TA = TJ = TMIN to TMAX ±59
LM4040EIM7 TA = TJ = 25°C 45 65
LM4040EIZ TA = TJ = TMIN to TMAX 70
IR = 10 mA ±20
LM4040CIM3 TA = TJ = 25°C ±15
LM4040CIZ
LM4040CIM7 TA = TJ = TMIN to TMAX ±100
Average Reverse
Breakdown Voltage LM4040DIM3 TA = TJ = 25°C ±15
ΔVR/ΔT IR = 1 mA LM4040DIZ ppm/°C
Temperature
LM4040DIM7 TA = TJ = TMIN to TMAX ±150
Coefficient (3)
LM4040EIM7 TA = TJ = 25°C ±15
LM4040EIZ TA = TJ = TMIN to TMAX ±150
IR = 100 μA ±15
(1) Limits are 100% production tested at 25°C. Limits over temperature are ensured through correlation using Statistical Quality Control
(SQC) methods. The limits are used to calculate AOQL.
(2) Typicals are at TJ = 25°C and represent most likely parametric norm.
(3) The overtemperature limit for Reverse Breakdown Voltage Tolerance is defined as the room temperature Reverse Breakdown Voltage
Tolerance ±[(ΔVR/ΔT)(maxΔT)(VR)]. Where, ΔVR/ΔT is the VR temperature coefficient, maxΔT is the maximum difference in temperature
from the reference point of 25°C to T MIN or TMAX, and VR is the reverse breakdown voltage. The total overtemperature tolerance for the
different grades in the industrial temperature range where maxΔT = 65°C is shown below:
A-grade: ±0.75% = ±0.1% ±100 ppm/°C × 65°C
B-grade: ±0.85% = ±0.2% ±100 ppm/°C × 65°C
C-grade: ±1.15% = ±0.5% ±100 ppm/°C × 65°C
D-grade: ±1.98% = ±1.0% ±150 ppm/°C × 65°C
E-grade: ±2.98% = ±2.0% ±150 ppm/°C × 65°C
The total overtemperature tolerance for the different grades in the extended temperature range where max ΔT = 100 °C is shown below:
C-grade: ±1.5% = ±0.5% ±100 ppm/°C × 100°C
D-grade: ±2.5% = ±1.0% ±150 ppm/°C × 100°C
E-grade: ±3.5% = ±2.0% ±150 ppm/°C × 100°C
Therefore, as an example, the A-grade 2.5-V LM4040-N has an overtemperature Reverse Breakdown Voltage tolerance of ±2.5V ×
0.75% = ±19 mV.
18 Submit Documentation Feedback Copyright © 2000–2016, Texas Instruments Incorporated
Electrical Characteristics: 3-V LM4040-N VR Tolerance Grades 'C', 'D', And 'E'; Temperature
Grade 'I' (continued)
all other limits TA = TJ = 25°C. The grades C, D and E designate initial Reverse Breakdown Voltage tolerances of ±0.5%, ±1%
and ±2%, respectively.
PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
LM4040CIM3 TA = TJ = 25°C 0.4 0.8
LM4040CIZ
LM4040CIM7 TA = TJ = TMIN to TMAX 1.1
(4) Load regulation is measured on pulse basis from no load to the specified load current. Output changes due to die temperature change
must be taken into account separately.
(5) Thermal hysteresis is defined as the difference in voltage measured at +25°C after cycling to temperature -40°C and the 25°C
measurement after cycling to temperature 125°C.
6.13 Electrical Characteristics: 3-V LM4040-N VR Tolerance Grades 'C', 'D', And 'E';
Temperature Grade 'E'
all other limits TA = TJ = 25°C. The grades C, D and E designate initial Reverse Breakdown Voltage tolerances of ±0.5%, ±1%
and ±2%, respectively.
PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
Reverse Breakdown
IR = 100 μA 3 V
Voltage
TA = TJ = 25°C ±15
LM4040CEM3
TA = TJ = TMIN to TMAX ±45
VR
Reverse Breakdown TA = TJ = 25°C ±30
I = 100 μA LM4040DEM3 mV
Voltage Tolerance (3) R TA = TJ = TMIN to TMAX ±75
TA = TJ = 25°C ±60
LM4040EEM3
TA = TJ = TMIN to TMAX ±105
TA = TJ = 25°C 47 62
LM4040CEM3
TA = TJ = TMIN to TMAX 70
(1) Limits are 100% production tested at 25°C. Limits over temperature are ensured through correlation using Statistical Quality Control
(SQC) methods. The limits are used to calculate AOQL.
(2) Typicals are at TJ = 25°C and represent most likely parametric norm.
(3) The (overtemperature) limit for Reverse Breakdown Voltage Tolerance is defined as the room temperature Reverse Breakdown Voltage
Tolerance ±[(ΔVR/ΔT)(maxΔT)(VR)]. Where, ΔVR/ΔT is the VR temperature coefficient, maxΔT is the maximum difference in temperature
from the reference point of 25°C to T MIN or TMAX, and VR is the reverse breakdown voltage. The total overtemperature tolerance for the
different grades in the industrial temperature range where maxΔT = 65°C is shown below:
A-grade: ±0.75% = ±0.1% ±100 ppm/°C × 65°C
B-grade: ±0.85% = ±0.2% ±100 ppm/°C × 65°C
C-grade: ±1.15% = ±0.5% ±100 ppm/°C × 65°C
D-grade: ±1.98% = ±1.0% ±150 ppm/°C × 65°C
E-grade: ±2.98% = ±2.0% ±150 ppm/°C × 65°C
The total overtemperature tolerance for the different grades in the extended temperature range where max ΔT = 100 °C is shown below:
C-grade: ±1.5% = ±0.5% ±100 ppm/°C × 100°C
D-grade: ±2.5% = ±1.0% ±150 ppm/°C × 100°C
E-grade: ±3.5% = ±2.0% ±150 ppm/°C × 100°C
Therefore, as an example, the A-grade 2.5-V LM4040-N has an overtemperature Reverse Breakdown Voltage tolerance of ±2.5V ×
0.75% = ±19 mV.
(4) Load regulation is measured on pulse basis from no load to the specified load current. Output changes due to die temperature change
must be taken into account separately.
20 Submit Documentation Feedback Copyright © 2000–2016, Texas Instruments Incorporated
Electrical Characteristics: 3-V LM4040-N VR Tolerance Grades 'C', 'D', And 'E'; Temperature
Grade 'E' (continued)
all other limits TA = TJ = 25°C. The grades C, D and E designate initial Reverse Breakdown Voltage tolerances of ±0.5%, ±1%
and ±2%, respectively.
PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
LM4040CEM3 0.4 0.9
IR = 1 mA, f = 120
Reverse Dynamic
ZR Hz, LM4040DEM3 0.4 1.2 Ω
Impedance
IAC = 0.1 IR
LM4040EEM3 0.4 1.2
IR = 100 μA
eN Wideband Noise 35 μVrms
10 Hz ≤ f ≤ 10 kHz
Reverse Breakdown t = 1000 hrs
ΔVR Voltage Long Term T = 25°C ±0.1°C 120 ppm
Stability IR = 100 μA
Thermal
VHYST ΔT = −40°C to 125°C 0.08%
Hysteresis (5)
(5) Thermal hysteresis is defined as the difference in voltage measured at +25°C after cycling to temperature -40°C and the 25°C
measurement after cycling to temperature 125°C.
6.14 Electrical Characteristics: 4.1-V LM4040-N VR Tolerance Grades 'A' And 'B'; Temperature
Grade 'I'
all other limits TA = TJ = 25°C. The grades A and B designate initial Reverse Breakdown Voltage tolerances of ±0.1% and
±0.2%, respectively.
PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
Reverse Breakdown
IR = 100 μA 4.096 V
Voltage
(1) Limits are 100% production tested at 25°C. Limits over temperature are ensured through correlation using Statistical Quality Control
(SQC) methods. The limits are used to calculate AOQL.
(2) Typicals are at TJ = 25°C and represent most likely parametric norm.
(3) The (overtemperature) limit for Reverse Breakdown Voltage Tolerance is defined as the room temperature Reverse Breakdown Voltage
Tolerance ±[(ΔVR/ΔT)(maxΔT)(VR)]. Where, ΔVR/ΔT is the VR temperature coefficient, maxΔT is the maximum difference in temperature
from the reference point of 25°C to T MIN or TMAX, and VR is the reverse breakdown voltage. The total overtemperature tolerance for the
different grades in the industrial temperature range where maxΔT = 65°C is shown below:
A-grade: ±0.75% = ±0.1% ±100 ppm/°C × 65°C
B-grade: ±0.85% = ±0.2% ±100 ppm/°C × 65°C
C-grade: ±1.15% = ±0.5% ±100 ppm/°C × 65°C
D-grade: ±1.98% = ±1.0% ±150 ppm/°C × 65°C
E-grade: ±2.98% = ±2.0% ±150 ppm/°C × 65°C
The total overtemperature tolerance for the different grades in the extended temperature range where max ΔT = 100 °C is shown below:
C-grade: ±1.5% = ±0.5% ±100 ppm/°C × 100°C
D-grade: ±2.5% = ±1.0% ±150 ppm/°C × 100°C
E-grade: ±3.5% = ±2.0% ±150 ppm/°C × 100°C
Therefore, as an example, the A-grade 2.5-V LM4040-N has an overtemperature Reverse Breakdown Voltage tolerance of ±2.5V ×
0.75% = ±19 mV.
(4) Load regulation is measured on pulse basis from no load to the specified load current. Output changes due to die temperature change
must be taken into account separately.
Copyright © 2000–2016, Texas Instruments Incorporated Submit Documentation Feedback 21
Product Folder Links: LM4040-N LM4040-N-Q1
LM4040-N, LM4040-N-Q1
SNOS633K – OCTOBER 2000 – REVISED JUNE 2016 www.ti.com
Electrical Characteristics: 4.1-V LM4040-N VR Tolerance Grades 'A' And 'B'; Temperature Grade
'I' (continued)
all other limits TA = TJ = 25°C. The grades A and B designate initial Reverse Breakdown Voltage tolerances of ±0.1% and
±0.2%, respectively.
PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
Reverse Dynamic IR = 1 mA, f = 120 Hz,
ZR 0.5 1 Ω
Impedance IAC = 0.1 IR
IR = 100 μA
eN Wideband Noise 80 μVrms
10 Hz ≤ f ≤ 10 kHz
Reverse Breakdown t = 1000 hrs
ΔVR Voltage Long Term T = 25°C ±0.1°C 120 ppm
Stability IR = 100 μA
VHYST Thermal Hysteresis (5) ΔT = −40°C to 125°C 0.08%
(5) Thermal hysteresis is defined as the difference in voltage measured at +25°C after cycling to temperature -40°C and the 25°C
measurement after cycling to temperature 125°C.
6.15 Electrical Characteristics: 4.1-V LM4040-N VR Tolerance Grades 'C' and 'D'; Temperature
Grade 'I'
all other limits TA = TJ = 25°C. The grades C and D designate initial Reverse Breakdown Voltage tolerances of ±0.5% and
±1%, respectively.
PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
Reverse Breakdown
IR = 100 μA 4.096 V
Voltage
LM4040CIM3 TA = TJ = 25°C ±20
LM4040CIZ
VR TA = TJ = TMIN to TMAX ±47
Reverse Breakdown LM4040CIM7
IR = 100 μA mV
Voltage Tolerance (3) LM4040DIM3 TA = TJ = 25°C ±41
LM4040DIZ
LM4040DIM7 TA = TJ = TMIN to TMAX ±81
LM4040CIM3 TA = TJ = 25°C 50 68
LM4040CIZ
LM4040CIM7 TA = TJ = TMIN to TMAX 73
Minimum Operating
IRMIN μA
Current LM4040DIM3 TA = TJ = 25°C 50 73
LM4040DIZ
LM4040DIM7 TA = TJ = TMIN to TMAX 78
IR = 10 mA ±30
LM4040CIM3 TA = TJ = 25°C ±20
Average Reverse LM4040CIZ
LM4040CIM7 TA = TJ = TMIN to TMAX ±100
ΔVR/ Breakdown Voltage
IR = 1 mA ppm/°C
ΔT Temperature LM4040DIM3 TA = TJ = 25°C ±20
Coefficient (3) LM4040DIZ
LM4040DIM7 TA = TJ = TMIN to TMAX ±150
IR = 100 μA ±20
(1) Limits are 100% production tested at 25°C. Limits over temperature are ensured through correlation using Statistical Quality Control
(SQC) methods. The limits are used to calculate AOQL.
(2) Typicals are at TJ = 25°C and represent most likely parametric norm.
(3) The (overtemperature) limit for Reverse Breakdown Voltage Tolerance is defined as the room temperature Reverse Breakdown Voltage
Tolerance ±[(ΔVR/ΔT)(maxΔT)(VR)]. Where, ΔVR/ΔT is the VR temperature coefficient, maxΔT is the maximum difference in temperature
from the reference point of 25°C to T MIN or TMAX, and VR is the reverse breakdown voltage. The total overtemperature tolerance for the
different grades in the industrial temperature range where maxΔT = 65°C is shown below:
A-grade: ±0.75% = ±0.1% ±100 ppm/°C × 65°C
B-grade: ±0.85% = ±0.2% ±100 ppm/°C × 65°C
C-grade: ±1.15% = ±0.5% ±100 ppm/°C × 65°C
D-grade: ±1.98% = ±1.0% ±150 ppm/°C × 65°C
E-grade: ±2.98% = ±2.0% ±150 ppm/°C × 65°C
The total overtemperature tolerance for the different grades in the extended temperature range where max ΔT = 100 °C is shown below:
C-grade: ±1.5% = ±0.5% ±100 ppm/°C × 100°C
D-grade: ±2.5% = ±1.0% ±150 ppm/°C × 100°C
E-grade: ±3.5% = ±2.0% ±150 ppm/°C × 100°C
Therefore, as an example, the A-grade 2.5-V LM4040-N has an overtemperature Reverse Breakdown Voltage tolerance of ±2.5V ×
0.75% = ±19 mV.
22 Submit Documentation Feedback Copyright © 2000–2016, Texas Instruments Incorporated
Electrical Characteristics: 4.1-V LM4040-N VR Tolerance Grades 'C' and 'D'; Temperature Grade
'I' (continued)
all other limits TA = TJ = 25°C. The grades C and D designate initial Reverse Breakdown Voltage tolerances of ±0.5% and
±1%, respectively.
PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
LM4040CIM3 TA = TJ = 25°C 0.5 0.9
LM4040CIZ
TA = TJ = TMIN to TMAX 1.2
LM4040CIM7
IRMIN ≤ IR ≤ 1 mA
LM4040DIM3 TA = TJ = 25°C 0.5 1.2
Reverse Breakdown LM4040DIZ
LM4040DIM7 TA = TJ = TMIN to TMAX 1.5
ΔVR/ Voltage Change with
mV
ΔIR Operating Current LM4040CIM3 TA = TJ = 25°C 3 7
Change (4) LM4040CIZ
TA = TJ = TMIN to TMAX 10
LM4040CIM7
1 mA ≤ IR ≤ 15 mA
LM4040DIM3 TA = TJ = 25°C 3 9
LM4040DIZ
LM4040DIM7 TA = TJ = TMIN to TMAX 13
LM4040CIM3
LM4040CIZ 0.5 1
Reverse Dynamic IR = 1 mA, f = 120 Hz, LM4040CIM7
ZR Ω
Impedance IAC = 0.1 IR LM4040DIM3
LM4040DIZ 0.5 1.3
LM4040DIM7
IR = 100 μA
eN Wideband Noise 80 μVrms
10 Hz ≤ f ≤ 10 kHz
Reverse Breakdown t = 1000 hrs
ΔVR Voltage Long Term T = 25°C ±0.1°C 120 ppm
Stability IR = 100 μA
VHYST Thermal Hysteresis (5) ΔT = −40°C to 125°C 0.08%
(4) Load regulation is measured on pulse basis from no load to the specified load current. Output changes due to die temperature change
must be taken into account separately.
(5) Thermal hysteresis is defined as the difference in voltage measured at +25°C after cycling to temperature -40°C and the 25°C
measurement after cycling to temperature 125°C.
6.16 Electrical Characteristics: 5-V LM4040-N VR Tolerance Grades 'A' And 'B'; Temperature
Grade 'I'
all other limits TA = TJ = 25°C. The grades A and B designate initial Reverse Breakdown Voltage tolerances of ±0.1% and
±0.2%, respectively.
PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
Reverse Breakdown
IR = 100 μA 5 V
Voltage
LM4040AIM3 TA = TJ = 25°C ±5
VR LM4040AIZ TA = TJ = TMIN to TMAX ±38
Reverse Breakdown
IR = 100 μA mV
Voltage Tolerance (3) LM4040BIM3 TA = TJ = 25°C ±10
LM4040BIZ
LM4040BIM7 TA = TJ = TMIN to TMAX ±43
(1) Limits are 100% production tested at 25°C. Limits over temperature are ensured through correlation using Statistical Quality Control
(SQC) methods. The limits are used to calculate AOQL.
(2) Typicals are at TJ = 25°C and represent most likely parametric norm.
(3) The (overtemperature) limit for Reverse Breakdown Voltage Tolerance is defined as the room temperature Reverse Breakdown Voltage
Tolerance ±[(ΔVR/ΔT)(maxΔT)(VR)]. Where, ΔVR/ΔT is the VR temperature coefficient, maxΔT is the maximum difference in temperature
from the reference point of 25°C to T MIN or TMAX, and VR is the reverse breakdown voltage. The total overtemperature tolerance for the
different grades in the industrial temperature range where maxΔT = 65°C is shown below:
A-grade: ±0.75% = ±0.1% ±100 ppm/°C × 65°C
B-grade: ±0.85% = ±0.2% ±100 ppm/°C × 65°C
C-grade: ±1.15% = ±0.5% ±100 ppm/°C × 65°C
D-grade: ±1.98% = ±1.0% ±150 ppm/°C × 65°C
E-grade: ±2.98% = ±2.0% ±150 ppm/°C × 65°C
The total overtemperature tolerance for the different grades in the extended temperature range where max ΔT = 100 °C is shown below:
C-grade: ±1.5% = ±0.5% ±100 ppm/°C × 100°C
D-grade: ±2.5% = ±1.0% ±150 ppm/°C × 100°C
E-grade: ±3.5% = ±2.0% ±150 ppm/°C × 100°C
Therefore, as an example, the A-grade 2.5-V LM4040-N has an overtemperature Reverse Breakdown Voltage tolerance of ±2.5V ×
0.75% = ±19 mV.
Copyright © 2000–2016, Texas Instruments Incorporated Submit Documentation Feedback 23
Product Folder Links: LM4040-N LM4040-N-Q1
LM4040-N, LM4040-N-Q1
SNOS633K – OCTOBER 2000 – REVISED JUNE 2016 www.ti.com
Electrical Characteristics: 5-V LM4040-N VR Tolerance Grades 'A' And 'B'; Temperature Grade
'I' (continued)
all other limits TA = TJ = 25°C. The grades A and B designate initial Reverse Breakdown Voltage tolerances of ±0.1% and
±0.2%, respectively.
PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
(4) Load regulation is measured on pulse basis from no load to the specified load current. Output changes due to die temperature change
must be taken into account separately.
(5) Thermal hysteresis is defined as the difference in voltage measured at +25°C after cycling to temperature -40°C and the 25°C
measurement after cycling to temperature 125°C.
6.17 Electrical Characteristics: 5-V LM4040-N VR Tolerance Grades 'C' And 'D'; Temperature
Grade 'I'
all other limits TA = TJ = 25°C. The grades C and D designate initial Reverse Breakdown Voltage tolerances of ±0.5% and
±1%, respectively.
PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
Reverse Breakdown
IR = 100 μA 5 V
Voltage
LM4040CIM3 TA = TJ = 25°C ±25
LM4040CIZ
VR TA = TJ = TMIN to TMAX ±58
Reverse Breakdown LM4040CIM7
IR = 100 μA mV
Voltage Tolerance (3) LM4040DIM3 TA = TJ = 25°C ±50
LM4040DIZ
LM4040DIM7 TA = TJ = TMIN to TMAX ±99
(1) Limits are 100% production tested at 25°C. Limits over temperature are ensured through correlation using Statistical Quality Control
(SQC) methods. The limits are used to calculate AOQL.
(2) Typicals are at TJ = 25°C and represent most likely parametric norm.
(3) The (overtemperature) limit for Reverse Breakdown Voltage Tolerance is defined as the room temperature Reverse Breakdown Voltage
Tolerance ±[(ΔVR/ΔT)(maxΔT)(VR)]. Where, ΔVR/ΔT is the VR temperature coefficient, maxΔT is the maximum difference in temperature
from the reference point of 25°C to T MIN or TMAX, and VR is the reverse breakdown voltage. The total overtemperature tolerance for the
different grades in the industrial temperature range where maxΔT = 65°C is shown below:
A-grade: ±0.75% = ±0.1% ±100 ppm/°C × 65°C
B-grade: ±0.85% = ±0.2% ±100 ppm/°C × 65°C
C-grade: ±1.15% = ±0.5% ±100 ppm/°C × 65°C
D-grade: ±1.98% = ±1.0% ±150 ppm/°C × 65°C
E-grade: ±2.98% = ±2.0% ±150 ppm/°C × 65°C
The total overtemperature tolerance for the different grades in the extended temperature range where max ΔT = 100 °C is shown below:
C-grade: ±1.5% = ±0.5% ±100 ppm/°C × 100°C
D-grade: ±2.5% = ±1.0% ±150 ppm/°C × 100°C
E-grade: ±3.5% = ±2.0% ±150 ppm/°C × 100°C
Therefore, as an example, the A-grade 2.5-V LM4040-N has an overtemperature Reverse Breakdown Voltage tolerance of ±2.5V ×
0.75% = ±19 mV.
24 Submit Documentation Feedback Copyright © 2000–2016, Texas Instruments Incorporated
Electrical Characteristics: 5-V LM4040-N VR Tolerance Grades 'C' And 'D'; Temperature Grade
'I' (continued)
all other limits TA = TJ = 25°C. The grades C and D designate initial Reverse Breakdown Voltage tolerances of ±0.5% and
±1%, respectively.
PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
LM4040CIM3 TA = TJ = 25°C 54 74
LM4040CIZ
LM4040CIM7 TA = TJ = TMIN to TMAX 80
Minimum Operating
IRMIN μA
Current LM4040DIM3 TA = TJ = 25°C 54 79
LM4040DIZ
LM4040DIM7 TA = TJ = TMIN to TMAX 85
IR = 10 mA ±30
LM4040CIM3 TA = TJ = 25°C ±20
Average Reverse LM4040CIZ
LM4040CIM7 TA = TJ = TMIN to TMAX ±100
ΔVR/Δ Breakdown Voltage
IR = 1 mA ppm/°C
T Temperature LM4040DIM3 TA = TJ = 25°C ±20
Coefficient (3) LM4040DIZ
LM4040DIM7 TA = TJ = TMIN to TMAX ±150
IR = 100 μA ±20
LM4040CIM3 TA = TJ = 25°C 0.5 1
LM4040CIZ
LM4040CIM7 TA = TJ = TMIN to TMAX 1.4
IRMIN ≤ IR ≤ 1 mA
LM4040DIM3 TA = TJ = 25°C 0.5 1.3
Reverse Breakdown LM4040DIZ
LM4040DIM7 TA = TJ = TMIN to TMAX 1.8
ΔVR/Δ Voltage Change with
mV
IR Operating Current LM4040CIM3 TA = TJ = 25°C 3.5 8
Change (4) LM4040CIZ
LM4040CIM7 TA = TJ = TMIN to TMAX 12
1 mA ≤ IR ≤ 15 mA
LM4040DIM3 TA = TJ = 25°C 3.5 10
LM4040DIZ
LM4040DIM7 TA = TJ = TMIN to TMAX 15
(4) Load regulation is measured on pulse basis from no load to the specified load current. Output changes due to die temperature change
must be taken into account separately.
(5) Thermal hysteresis is defined as the difference in voltage measured at +25°C after cycling to temperature -40°C and the 25°C
measurement after cycling to temperature 125°C.
6.18 Electrical Characteristics: 5-V LM4040-N VR Tolerance Grades 'C' And 'D'; Temperature
Grade 'E'
all other limits TA = TJ = 25°C. The grades C and D designate initial Reverse Breakdown Voltage tolerances of ±0.5% and
±1%, respectively.
PARAMETER TEST CONDITIONS MIN (1) TYP MAX (1) UNIT
Reverse Breakdown
IR = 100 μA 5 V
Voltage
TA = TJ = 25°C ±25
VR LM4040CEM3
Reverse Breakdown TA = TJ = TMIN to TMAX ±75
IR = 100 μA mV
Voltage Tolerance (2) TA = TJ = 25°C ±50
LM4040DEM3
TA = TJ = TMIN to TMAX ±125
TA = TJ = 25°C 54 74
LM4040CEM3
Minimum Operating TA = TJ = TMIN to TMAX 83
IRMIN μA
Current TA = TJ = 25°C 54 79
LM4040DEM3
TA = TJ = TMIN to TMAX 88
IR = 10 mA ±30
TA = TJ = 25°C ±20
Average Reverse LM4040CEM3
ΔVR/ Breakdown Voltage TA = TJ = TMIN to TMAX ±100
IR = 1 mA ppm/°C
ΔT Temperature TA = TJ = 25°C ±20
Coefficient (2) LM4040DEM3
TA = TJ = TMIN to TMAX ±150
IR = 100 μA ±20
TA = TJ = 25°C 0.5 1
LM4040CEM3
TA = TJ = TMIN to TMAX 1.4
IRMIN ≤ IR ≤ 1 mA
TA = TJ = 25°C 0.5 1
Reverse Breakdown LM4040DEM3
ΔVR/ Voltage Change with TA = TJ = TMIN to TMAX 1.8
mV
ΔIR Operating Current TA = TJ = 25°C 3.5 8
Change (3) LM4040CEM3
TA = TJ = TMIN to TMAX 12
1 mA ≤ IR ≤ 15 mA
TA = TJ = 25°C 3.5 8
LM4040DEM3
TA = TJ = TMIN to TMAX 15
Reverse Dynamic IR = 1 mA, f = 120 Hz,
ZR 0.5 1.1 Ω
Impedance IAC = 0.1 IR
IR = 100 μA
eN Wideband Noise 80 μVrms
10 Hz ≤ f ≤ 10 kHz
Reverse Breakdown t = 1000 hrs
ΔVR Voltage Long Term T = 25°C ±0.1°C 120 ppm
Stability IR = 100 μA
VHYST Thermal Hysteresis (4) ΔT = −40°C to 125°C 0.08%
(1) Limits are 100% production tested at 25°C. Limits over temperature are ensured through correlation using Statistical Quality Control
(SQC) methods. The limits are used to calculate AOQL.
(2) The (overtemperature) limit for Reverse Breakdown Voltage Tolerance is defined as the room temperature Reverse Breakdown Voltage
Tolerance ±[(ΔVR/ΔT)(maxΔT)(VR)]. Where, ΔVR/ΔT is the VR temperature coefficient, maxΔT is the maximum difference in temperature
from the reference point of 25°C to T MIN or TMAX, and VR is the reverse breakdown voltage. The total overtemperature tolerance for the
different grades in the industrial temperature range where maxΔT = 65°C is shown below:
A-grade: ±0.75% = ±0.1% ±100 ppm/°C × 65°C
B-grade: ±0.85% = ±0.2% ±100 ppm/°C × 65°C
C-grade: ±1.15% = ±0.5% ±100 ppm/°C × 65°C
D-grade: ±1.98% = ±1.0% ±150 ppm/°C × 65°C
E-grade: ±2.98% = ±2.0% ±150 ppm/°C × 65°C
The total overtemperature tolerance for the different grades in the extended temperature range where max ΔT = 100 °C is shown below:
C-grade: ±1.5% = ±0.5% ±100 ppm/°C × 100°C
D-grade: ±2.5% = ±1.0% ±150 ppm/°C × 100°C
E-grade: ±3.5% = ±2.0% ±150 ppm/°C × 100°C
Therefore, as an example, the A-grade 2.5-V LM4040-N has an overtemperature Reverse Breakdown Voltage tolerance of ±2.5V ×
0.75% = ±19 mV.
(3) Load regulation is measured on pulse basis from no load to the specified load current. Output changes due to die temperature change
must be taken into account separately.
(4) Thermal hysteresis is defined as the difference in voltage measured at +25°C after cycling to temperature -40°C and the 25°C
measurement after cycling to temperature 125°C.
6.19 Electrical Characteristics: 8.2-V LM4040-N VR Tolerance Grades 'A' And 'B'; Temperature
Grade 'I'
all other limits TA = TJ = 25°C. The grades A and B designate initial Reverse Breakdown Voltage tolerances of ±0.1% and
±0.2%, respectively.
PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
Reverse Breakdown
IR = 150 μA 8.192 V
Voltage
(1) Limits are 100% production tested at 25°C. Limits over temperature are ensured through correlation using Statistical Quality Control
(SQC) methods. The limits are used to calculate AOQL.
(2) Typicals are at TJ = 25°C and represent most likely parametric norm.
(3) The (overtemperature) limit for Reverse Breakdown Voltage Tolerance is defined as the room temperature Reverse Breakdown Voltage
Tolerance ±[(ΔVR/ΔT)(maxΔT)(VR)]. Where, ΔVR/ΔT is the VR temperature coefficient, maxΔT is the maximum difference in temperature
from the reference point of 25°C to T MIN or TMAX, and VR is the reverse breakdown voltage. The total overtemperature tolerance for the
different grades in the industrial temperature range where maxΔT = 65°C is shown below:
A-grade: ±0.75% = ±0.1% ±100 ppm/°C × 65°C
B-grade: ±0.85% = ±0.2% ±100 ppm/°C × 65°C
C-grade: ±1.15% = ±0.5% ±100 ppm/°C × 65°C
D-grade: ±1.98% = ±1.0% ±150 ppm/°C × 65°C
E-grade: ±2.98% = ±2.0% ±150 ppm/°C × 65°C
The total overtemperature tolerance for the different grades in the extended temperature range where max ΔT = 100 °C is shown below:
C-grade: ±1.5% = ±0.5% ±100 ppm/°C × 100°C
D-grade: ±2.5% = ±1.0% ±150 ppm/°C × 100°C
E-grade: ±3.5% = ±2.0% ±150 ppm/°C × 100°C
Therefore, as an example, the A-grade 2.5-V LM4040-N has an overtemperature Reverse Breakdown Voltage tolerance of ±2.5V ×
0.75% = ±19 mV.
(4) Load regulation is measured on pulse basis from no load to the specified load current. Output changes due to die temperature change
must be taken into account separately.
(5) Thermal hysteresis is defined as the difference in voltage measured at +25°C after cycling to temperature -40°C and the 25°C
measurement after cycling to temperature 125°C.
6.20 Electrical Characteristics: 8.2-V Lm4040-N VR Tolerance Grades 'C' And 'D'; Temperature
Grade 'I'
all other limits TA = TJ = 25°C. The grades C and D designate initial Reverse Breakdown Voltage tolerances of ±0.5% and
±1%, respectively.
PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
Reverse Breakdown
IR = 150 μA 8.192 V
Voltage
LM4040CIM3 TA = TJ = 25°C 67 91
LM4040CIZ TA = TJ = TMIN to TMAX 95
Minimum Operating
IRMIN μA
Current TA = TJ = 25°C 67 96
LM4040DIM3
LM4040DIZ TA = TJ = TMIN to TMAX 100
IR = 10 mA ±40
(1) Limits are 100% production tested at 25°C. Limits over temperature are ensured through correlation using Statistical Quality Control
(SQC) methods. The limits are used to calculate AOQL.
(2) Typicals are at TJ = 25°C and represent most likely parametric norm.
(3) The (overtemperature) limit for Reverse Breakdown Voltage Tolerance is defined as the room temperature Reverse Breakdown Voltage
Tolerance ±[(ΔVR/ΔT)(maxΔT)(VR)]. Where, ΔVR/ΔT is the VR temperature coefficient, maxΔT is the maximum difference in temperature
from the reference point of 25°C to T MIN or TMAX, and VR is the reverse breakdown voltage. The total overtemperature tolerance for the
different grades in the industrial temperature range where maxΔT = 65°C is shown below:
A-grade: ±0.75% = ±0.1% ±100 ppm/°C × 65°C
B-grade: ±0.85% = ±0.2% ±100 ppm/°C × 65°C
C-grade: ±1.15% = ±0.5% ±100 ppm/°C × 65°C
D-grade: ±1.98% = ±1.0% ±150 ppm/°C × 65°C
E-grade: ±2.98% = ±2.0% ±150 ppm/°C × 65°C
The total overtemperature tolerance for the different grades in the extended temperature range where max ΔT = 100 °C is shown below:
C-grade: ±1.5% = ±0.5% ±100 ppm/°C × 100°C
D-grade: ±2.5% = ±1.0% ±150 ppm/°C × 100°C
E-grade: ±3.5% = ±2.0% ±150 ppm/°C × 100°C
Therefore, as an example, the A-grade 2.5-V LM4040-N has an overtemperature Reverse Breakdown Voltage tolerance of ±2.5V ×
0.75% = ±19 mV.
(4) Load regulation is measured on pulse basis from no load to the specified load current. Output changes due to die temperature change
must be taken into account separately.
(5) Thermal hysteresis is defined as the difference in voltage measured at +25°C after cycling to temperature -40°C and the 25°C
measurement after cycling to temperature 125°C.
6.21 Electrical Characteristics: 10-V LM4040-N VR Tolerance Grades 'A' And 'B'; Temperature
Grade 'I'
all other limits TA = TJ = 25°C. The grades A and B designate initial Reverse Breakdown Voltage tolerances of ±0.1% and
±0.2%, respectively.
PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
Reverse Breakdown
IR = 150 μA 10 V
Voltage
(1) Limits are 100% production tested at 25°C. Limits over temperature are ensured through correlation using Statistical Quality Control
(SQC) methods. The limits are used to calculate AOQL.
(2) Typicals are at TJ = 25°C and represent most likely parametric norm.
(3) The (overtemperature) limit for Reverse Breakdown Voltage Tolerance is defined as the room temperature Reverse Breakdown Voltage
Tolerance ±[(ΔVR/ΔT)(maxΔT)(VR)]. Where, ΔVR/ΔT is the VR temperature coefficient, maxΔT is the maximum difference in temperature
from the reference point of 25°C to T MIN or TMAX, and VR is the reverse breakdown voltage. The total overtemperature tolerance for the
different grades in the industrial temperature range where maxΔT = 65°C is shown below:
A-grade: ±0.75% = ±0.1% ±100 ppm/°C × 65°C
B-grade: ±0.85% = ±0.2% ±100 ppm/°C × 65°C
C-grade: ±1.15% = ±0.5% ±100 ppm/°C × 65°C
D-grade: ±1.98% = ±1.0% ±150 ppm/°C × 65°C
E-grade: ±2.98% = ±2.0% ±150 ppm/°C × 65°C
The total overtemperature tolerance for the different grades in the extended temperature range where max ΔT = 100 °C is shown below:
C-grade: ±1.5% = ±0.5% ±100 ppm/°C × 100°C
D-grade: ±2.5% = ±1.0% ±150 ppm/°C × 100°C
E-grade: ±3.5% = ±2.0% ±150 ppm/°C × 100°C
Therefore, as an example, the A-grade 2.5-V LM4040-N has an overtemperature Reverse Breakdown Voltage tolerance of ±2.5V ×
0.75% = ±19 mV.
(4) Load regulation is measured on pulse basis from no load to the specified load current. Output changes due to die temperature change
must be taken into account separately.
(5) Thermal hysteresis is defined as the difference in voltage measured at +25°C after cycling to temperature -40°C and the 25°C
measurement after cycling to temperature 125°C.
6.22 Electrical Characteristics: 10-V LM4040-N VR Tolerance Grades 'C' And 'D'; Temperature
Grade 'I'
all other limits TA = TJ = 25°C. The grades C and D designate initial Reverse Breakdown Voltage tolerances of ±0.5% and
±1%, respectively.
PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) UNIT
Reverse Breakdown IR = 150 μA 10 V
Voltage
(1) Limits are 100% production tested at 25°C. Limits over temperature are ensured through correlation using Statistical Quality Control
(SQC) methods. The limits are used to calculate AOQL.
(2) Typicals are at TJ = 25°C and represent most likely parametric norm.
(3) The (overtemperature) limit for Reverse Breakdown Voltage Tolerance is defined as the room temperature Reverse Breakdown Voltage
Tolerance ±[(ΔVR/ΔT)(maxΔT)(VR)]. Where, ΔVR/ΔT is the VR temperature coefficient, maxΔT is the maximum difference in temperature
from the reference point of 25°C to T MIN or TMAX, and VR is the reverse breakdown voltage. The total overtemperature tolerance for the
different grades in the industrial temperature range where maxΔT = 65°C is shown below:
A-grade: ±0.75% = ±0.1% ±100 ppm/°C × 65°C
B-grade: ±0.85% = ±0.2% ±100 ppm/°C × 65°C
C-grade: ±1.15% = ±0.5% ±100 ppm/°C × 65°C
D-grade: ±1.98% = ±1.0% ±150 ppm/°C × 65°C
E-grade: ±2.98% = ±2.0% ±150 ppm/°C × 65°C
The total overtemperature tolerance for the different grades in the extended temperature range where max ΔT = 100 °C is shown below:
C-grade: ±1.5% = ±0.5% ±100 ppm/°C × 100°C
D-grade: ±2.5% = ±1.0% ±150 ppm/°C × 100°C
E-grade: ±3.5% = ±2.0% ±150 ppm/°C × 100°C
Therefore, as an example, the A-grade 2.5-V LM4040-N has an overtemperature Reverse Breakdown Voltage tolerance of ±2.5V ×
0.75% = ±19 mV.
(4) Load regulation is measured on pulse basis from no load to the specified load current. Output changes due to die temperature change
must be taken into account separately.
(5) Thermal hysteresis is defined as the difference in voltage measured at +25°C after cycling to temperature -40°C and the 25°C
measurement after cycling to temperature 125°C.
Figure 1. Temperature Drift For Different Average Figure 2. Output Impedance vs Frequency
Temperature Coefficient
Figure 3. Output Impedance vs Frequency Figure 4. Reverse Characteristics And Minimum Operating
Current
RS = 30k RS = 30k
Figure 6. Input Voltage Step Response LM4040-N-2.5 Figure 7. Input Voltage Step Response LM4040-N-5
RS = 30k
8 Detailed Description
8.1 Overview
The LM4040 device is a precision micropower shunt voltage reference available in 7 different fixed-output
voltage options and three different packages to meet small footprint requirements. The part is also available in
five different tolerance grades.
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
(1)
**Ceramic monolithic
*Tantalum
Figure 12. 4.1-V LM4040-N'S Nominal 4.096 Breakdown Voltage Gives ADC12451 1 MV/LSB
Nominal clamping voltage is ±11.5 V (LM4040-N's reverse breakdown voltage +2 diode VF).
The bounding voltage is ±4 V with the 2.5-V LM4040-N (LM4040-N's reverse breakdown voltage + 3 diode VF).
11 Layout
RS
CIN COUT
12.4 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
12.5 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
www.ti.com 3-Oct-2018
PACKAGING INFORMATION
Orderable Device Status Package Type Package Pins Package Eco Plan Lead/Ball Finish MSL Peak Temp Op Temp (°C) Device Marking Samples
(1) Drawing Qty (2) (6) (3) (4/5)
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com 3-Oct-2018
Orderable Device Status Package Type Package Pins Package Eco Plan Lead/Ball Finish MSL Peak Temp Op Temp (°C) Device Marking Samples
(1) Drawing Qty (2) (6) (3) (4/5)
LM4040AIZ-2.5/NOPB ACTIVE TO-92 LP 3 1800 Green (RoHS CU SN N / A for Pkg Type 4040A
& no Sb/Br) IZ2.5
LM4040AIZ-4.1/NOPB ACTIVE TO-92 LP 3 1800 Green (RoHS CU SN N / A for Pkg Type 4040A
& no Sb/Br) IZ4.1
LM4040AIZ-5.0/NOPB ACTIVE TO-92 LP 3 1800 Green (RoHS CU SN N / A for Pkg Type 4040A
& no Sb/Br) IZ5.0
LM4040BIM3-10.0 NRND SOT-23 DBZ 3 1000 TBD Call TI Call TI R0B
LM4040BIM3-10.0/NOPB ACTIVE SOT-23 DBZ 3 1000 Green (RoHS CU SN Level-1-260C-UNLIM R0B
& no Sb/Br)
LM4040BIM3-2.0/NOPB ACTIVE SOT-23 DBZ 3 1000 Green (RoHS CU SN Level-1-260C-UNLIM RJB
& no Sb/Br)
LM4040BIM3-2.5 ACTIVE SOT-23 DBZ 3 1000 TBD Call TI Call TI R2B
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com 3-Oct-2018
Orderable Device Status Package Type Package Pins Package Eco Plan Lead/Ball Finish MSL Peak Temp Op Temp (°C) Device Marking Samples
(1) Drawing Qty (2) (6) (3) (4/5)
Addendum-Page 3
PACKAGE OPTION ADDENDUM
www.ti.com 3-Oct-2018
Orderable Device Status Package Type Package Pins Package Eco Plan Lead/Ball Finish MSL Peak Temp Op Temp (°C) Device Marking Samples
(1) Drawing Qty (2) (6) (3) (4/5)
Addendum-Page 4
PACKAGE OPTION ADDENDUM
www.ti.com 3-Oct-2018
Orderable Device Status Package Type Package Pins Package Eco Plan Lead/Ball Finish MSL Peak Temp Op Temp (°C) Device Marking Samples
(1) Drawing Qty (2) (6) (3) (4/5)
Addendum-Page 5
PACKAGE OPTION ADDENDUM
www.ti.com 3-Oct-2018
Orderable Device Status Package Type Package Pins Package Eco Plan Lead/Ball Finish MSL Peak Temp Op Temp (°C) Device Marking Samples
(1) Drawing Qty (2) (6) (3) (4/5)
Addendum-Page 6
PACKAGE OPTION ADDENDUM
www.ti.com 3-Oct-2018
Orderable Device Status Package Type Package Pins Package Eco Plan Lead/Ball Finish MSL Peak Temp Op Temp (°C) Device Marking Samples
(1) Drawing Qty (2) (6) (3) (4/5)
LM4040DIZ-2.5/NOPB ACTIVE TO-92 LP 3 1800 Green (RoHS CU SN N / A for Pkg Type 4040D
& no Sb/Br) IZ2.5
LM4040DIZ-4.1/NOPB ACTIVE TO-92 LP 3 1800 Green (RoHS CU SN N / A for Pkg Type 4040D
& no Sb/Br) IZ4.1
LM4040DIZ-5.0/LFT1 ACTIVE TO-92 LP 3 2000 Green (RoHS CU SN N / A for Pkg Type 4040D
& no Sb/Br) IZ5.0
LM4040DIZ-5.0/NOPB ACTIVE TO-92 LP 3 1800 Green (RoHS CU SN N / A for Pkg Type 4040D
& no Sb/Br) IZ5.0
LM4040EEM3-2.5/NOPB ACTIVE SOT-23 DBZ 3 1000 Green (RoHS CU SN Level-1-260C-UNLIM R2E
& no Sb/Br)
LM4040EIM3-2.5 NRND SOT-23 DBZ 3 1000 TBD Call TI Call TI R2E
LM4040EIM3-2.5/NOPB ACTIVE SOT-23 DBZ 3 1000 Green (RoHS CU SN Level-1-260C-UNLIM R2E
& no Sb/Br)
LM4040EIM3-3.0/NOPB ACTIVE SOT-23 DBZ 3 1000 Green (RoHS CU SN Level-1-260C-UNLIM RKE
& no Sb/Br)
LM4040EIM3X-2.5 NRND SOT-23 DBZ 3 3000 TBD Call TI Call TI R2E
LM4040EIM3X-2.5/NOPB ACTIVE SOT-23 DBZ 3 3000 Green (RoHS CU SN Level-1-260C-UNLIM R2E
& no Sb/Br)
LM4040EIM3X-3.0/NOPB ACTIVE SOT-23 DBZ 3 3000 Green (RoHS CU SN Level-1-260C-UNLIM RKE
& no Sb/Br)
LM4040EIM7-2.0/NOPB ACTIVE SC70 DCK 5 1000 Green (RoHS CU SN Level-1-260C-UNLIM RJE
& no Sb/Br)
LM4040QAIM3-2.5/NOPB ACTIVE SOT-23 DBZ 3 1000 Green (RoHS CU SN Level-1-260C-UNLIM R6A
& no Sb/Br)
LM4040QAIM3X2.5/NOPB ACTIVE SOT-23 DBZ 3 3000 Green (RoHS CU SN Level-1-260C-UNLIM R6A
& no Sb/Br)
LM4040QBIM3-2.5/NOPB ACTIVE SOT-23 DBZ 3 1000 Green (RoHS CU SN Level-1-260C-UNLIM R6B
& no Sb/Br)
LM4040QBIM3X2.5/NOPB ACTIVE SOT-23 DBZ 3 3000 Green (RoHS CU SN Level-1-260C-UNLIM R6B
& no Sb/Br)
LM4040QCEM3-2.5/NOPB ACTIVE SOT-23 DBZ 3 1000 Green (RoHS CU SN Level-1-260C-UNLIM R2C
& no Sb/Br)
LM4040QCEM3-3.0/NOPB ACTIVE SOT-23 DBZ 3 1000 Green (RoHS CU SN Level-1-260C-UNLIM -40 to 125 R3C
& no Sb/Br)
LM4040QCIM3-2.5/NOPB ACTIVE SOT-23 DBZ 3 1000 Green (RoHS CU SN Level-1-260C-UNLIM R6C
& no Sb/Br)
Addendum-Page 7
PACKAGE OPTION ADDENDUM
www.ti.com 3-Oct-2018
Orderable Device Status Package Type Package Pins Package Eco Plan Lead/Ball Finish MSL Peak Temp Op Temp (°C) Device Marking Samples
(1) Drawing Qty (2) (6) (3) (4/5)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
Addendum-Page 8
PACKAGE OPTION ADDENDUM
www.ti.com 3-Oct-2018
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
• Catalog: LM4040-N
• Automotive: LM4040-N-Q1
Addendum-Page 9
PACKAGE MATERIALS INFORMATION
www.ti.com 29-Sep-2019
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com 29-Sep-2019
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com 29-Sep-2019
Pack Materials-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com 29-Sep-2019
Pack Materials-Page 4
PACKAGE MATERIALS INFORMATION
www.ti.com 29-Sep-2019
Pack Materials-Page 5
PACKAGE MATERIALS INFORMATION
www.ti.com 29-Sep-2019
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM4040BIM3-10.0/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040BIM3-2.0/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040BIM3-2.5 SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040BIM3-2.5/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040BIM3-3.0 SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040BIM3-3.0/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040BIM3-4.1 SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040BIM3-4.1/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040BIM3-5.0 SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040BIM3-5.0/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040BIM3-8.2 SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040BIM3-8.2/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040BIM3X-10/NOPB SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040BIM3X-2.0/NOPB SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040BIM3X-2.5 SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040BIM3X-2.5/NOPB SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040BIM3X-3.0/NOPB SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040BIM3X-4.1 SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040BIM3X-4.1/NOPB SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040BIM3X-5.0/NOPB SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040BIM7-2.0/NOPB SC70 DCK 5 1000 210.0 185.0 35.0
LM4040BIM7-2.5 SC70 DCK 5 1000 210.0 185.0 35.0
LM4040BIM7-2.5/NOPB SC70 DCK 5 1000 210.0 185.0 35.0
LM4040BIM7-5.0/NOPB SC70 DCK 5 1000 210.0 185.0 35.0
LM4040BIM7X-2.5/NOPB SC70 DCK 5 3000 210.0 185.0 35.0
LM4040CEM3-2.5 SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040CEM3-2.5/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040CEM3-3.0/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040CEM3-5.0 SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040CEM3-5.0/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040CEM3X-3.0/NOPB SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040CEM3X-5.0/NOPB SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040CIM3-10.0 SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040CIM3-10.0/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040CIM3-2.0 SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040CIM3-2.0/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040CIM3-2.5 SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040CIM3-2.5/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040CIM3-3.0 SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040CIM3-3.0/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040CIM3-4.1 SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040CIM3-4.1/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040CIM3-5.0 SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040CIM3-5.0/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
Pack Materials-Page 6
PACKAGE MATERIALS INFORMATION
www.ti.com 29-Sep-2019
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM4040CIM3-8.2 SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040CIM3-8.2/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040CIM3X-10/NOPB SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040CIM3X-2.0/NOPB SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040CIM3X-2.5 SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040CIM3X-2.5/NOPB SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040CIM3X-3.0/NOPB SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040CIM3X-4.1/NOPB SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040CIM3X-5.0 SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040CIM3X-5.0/NOPB SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040CIM7-2.0/NOPB SC70 DCK 5 1000 210.0 185.0 35.0
LM4040CIM7-2.5/NOPB SC70 DCK 5 1000 210.0 185.0 35.0
LM4040CIM7X-2.5/NOPB SC70 DCK 5 3000 210.0 185.0 35.0
LM4040DEM3-2.0 SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040DEM3-2.0/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040DEM3-2.5/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040DEM3-3.0/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040DEM3-5.0 SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040DEM3-5.0/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040DEM3X-2.5/NOPB SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040DEM3X-5.0/NOPB SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040DIM3-10.0 SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040DIM3-10.0/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040DIM3-2.0/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040DIM3-2.5 SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040DIM3-2.5/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040DIM3-3.0/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040DIM3-4.1 SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040DIM3-4.1/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040DIM3-5.0 SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040DIM3-5.0/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040DIM3-8.2/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040DIM3X-10/NOPB SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040DIM3X-2.0/NOPB SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040DIM3X-2.5 SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040DIM3X-2.5/NOPB SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040DIM3X-3.0/NOPB SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040DIM3X-4.1/NOPB SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040DIM3X-5.0 SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040DIM3X-5.0/NOPB SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040DIM7-2.0/NOPB SC70 DCK 5 1000 210.0 185.0 35.0
LM4040DIM7-2.5/NOPB SC70 DCK 5 1000 210.0 185.0 35.0
LM4040DIM7-5.0 SC70 DCK 5 1000 210.0 185.0 35.0
LM4040DIM7-5.0/NOPB SC70 DCK 5 1000 210.0 185.0 35.0
Pack Materials-Page 7
PACKAGE MATERIALS INFORMATION
www.ti.com 29-Sep-2019
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM4040EEM3-2.5/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040EIM3-2.5 SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040EIM3-2.5/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040EIM3-3.0/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040EIM3X-2.5 SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040EIM3X-2.5/NOPB SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040EIM3X-3.0/NOPB SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040EIM7-2.0/NOPB SC70 DCK 5 1000 210.0 185.0 35.0
LM4040QAIM3-2.5/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040QAIM3X2.5/NOPB SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040QBIM3-2.5/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040QBIM3X2.5/NOPB SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040QCEM3-2.5/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040QCEM3-3.0/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040QCIM3-2.5/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040QCIM3X2.5/NOPB SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040QDEM3-2.5/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040QDEM3-3.0/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040QDIM3-2.5/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040QDIM3X2.5/NOPB SOT-23 DBZ 3 3000 210.0 185.0 35.0
LM4040QEEM3-2.5/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040QEEM3-3.0/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040QEIM3-2.5/NOPB SOT-23 DBZ 3 1000 210.0 185.0 35.0
LM4040QEIM3X2.5/NOPB SOT-23 DBZ 3 3000 210.0 185.0 35.0
Pack Materials-Page 8
PACKAGE OUTLINE
LP0003A SCALE 1.200 SCALE 1.200
TO-92 - 5.34 mm max height
TO-92
5.21
4.44
EJECTOR PIN
OPTIONAL
5.34
4.32
(1.5) TYP
(2.54) SEATING
2X NOTE 3 PLANE
4 MAX
(0.51) TYP
6X
0.076 MAX
SEATING
PLANE
3X
12.7 MIN
0.43
2X 0.55 3X
3X 0.35
2.6 0.2 0.38
2X 1.27 0.13
FORMED LEAD OPTION
OTHER DIMENSIONS IDENTICAL STRAIGHT LEAD OPTION
TO STRAIGHT LEAD OPTION
2.67
3X
2.03 4.19
3.17
3 2 1
3.43 MIN
4215214/B 04/2017
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. Lead dimensions are not controlled within this area.
4. Reference JEDEC TO-226, variation AA.
5. Shipping method:
a. Straight lead option available in bulk pack only.
b. Formed lead option available in tape and reel or ammo pack.
c. Specific products can be offered in limited combinations of shipping medium and lead options.
d. Consult product folder for more information on available options.
www.ti.com
EXAMPLE BOARD LAYOUT
LP0003A TO-92 - 5.34 mm max height
TO-92
FULL R
0.05 MAX (1.07) TYP
ALL AROUND METAL 3X ( 0.85) HOLE
TYP TYP
2X
METAL
(1.5) 2X (1.5)
2X
SOLDER MASK
OPENING
1 2 3
(R0.05) TYP 2X (1.07)
(1.27)
SOLDER MASK
(2.54)
OPENING
METAL
2X
1 2 3 SOLDER MASK
(R0.05) TYP
(2.6) OPENING
SOLDER MASK
OPENING (5.2)
4215214/B 04/2017
www.ti.com
TAPE SPECIFICATIONS
LP0003A TO-92 - 5.34 mm max height
TO-92
13.7
11.7
32
23
16.5
15.5
11.0 9.75
8.5 8.50
19.0
17.5
4215214/B 04/2017
www.ti.com
4203227/C
PACKAGE OUTLINE
DBZ0003A SCALE 4.000
SOT-23 - 1.12 mm max height
SMALL OUTLINE TRANSISTOR
2.64 C
2.10
1.12 MAX
1.4
B A
1.2 0.1 C
PIN 1
INDEX AREA
0.95
3.04
1.9 2.80
3
2
0.5
3X
0.3
0.10
0.2 C A B (0.95) TYP
0.01
0.25
GAGE PLANE 0.20
TYP
0.08
0.6
TYP SEATING PLANE
0 -8 TYP 0.2
4214838/C 04/2017
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. Reference JEDEC registration TO-236, except minimum foot length.
www.ti.com
EXAMPLE BOARD LAYOUT
DBZ0003A SOT-23 - 1.12 mm max height
SMALL OUTLINE TRANSISTOR
PKG
3X (1.3)
1
3X (0.6)
SYMM
3
2X (0.95)
(R0.05) TYP
(2.1)
SOLDER MASK
SOLDER MASK METAL METAL UNDER OPENING
OPENING SOLDER MASK
4214838/C 04/2017
NOTES: (continued)
www.ti.com
EXAMPLE STENCIL DESIGN
DBZ0003A SOT-23 - 1.12 mm max height
SMALL OUTLINE TRANSISTOR
PKG
3X (1.3)
1
3X (0.6)
SYMM
3
2X(0.95)
(R0.05) TYP
(2.1)
4214838/C 04/2017
NOTES: (continued)
6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
7. Board assembly site may have different recommendations for stencil design.
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2019, Texas Instruments Incorporated