7234

CATALOGO internacional 2011:CATALOGO internacional 2010_imprenta.
qxd 27/07/2011 9:38 Página 50
ELECTRONICS
TERRESTRIAL/SATELLITE TV
Avant 3
PRODUCT RANGE
REF. DESCRIPTION
5326 Avant 3
5327 Avant 3 (Broadband VHF)
Accesories
7234 Universal Programming Unit
Main features
5 UHF filters and 1 VHF filter p 5326
2 UHF inputs with two possible filter assig-

ments (2-3 or 5-0); each filter can cluster up
to 7 channels.
VHF input that can cluster up to 4 channels

(7-28 MHz) (only 5326)
Input loopthru to mix the output of another

AVANT3
Broadband output to another AVANT3
Split-band amplification
FM/BI input
p 7234
Reference 5326 /5327

BIII VHF
Inputs UHF 1 UHF 2 FM/BI IN/MIX
(ref. 5326) (ref. 5327)
CCIR
CCIR 47-68 47-406/ 174-300 UHF1
Bandwidth MHz Ch. 5-Ch. 12
Ch. 21-Ch. 69 87-108 470-862 470-862
Ch. S11-Ch. S20
Number of filters/output 2/5 3/0 - 1 - -
Number of channels/filter 1-5(B.IV) /1-7(B.V) - 1-4 - - UHF2
General attenuation 0-20 BIII-DAB

dB
Filter attenuation 0-15 - 0-15 - -
FM
Input level 60-80 65-90 65-90 - -
Output level dBµV 117 - 115 113/116 -
Output level IMD3 114 - 112 110/113 -
Rejection 20 (±16 MHz) 20 (±16 MHz) 20 (±8 MHz) - -
dB
Noise figure 9 typ / 7 typ 9 typ / 7 typ -
Input powering (12 dB) 50 mA 50 mA - 50 mA - -
Vac Out
Powering voltage 230±20% - 50/60 Hz
50 Product Catalogue
CATALOGO internacional 2011:CATALOGO internacional 2010_imprenta.qxd 27/07/2011 9:38 Página 51
ELECTRONICS
T03 HEADEND EQUIPMENT
T03. Single Channel Amplification

PRODUCT RANGE 4529 units
Power supply
Re f . De SCRIPTION
5498 T03 PSU 24V/60 W
502905 T03/T05 PSU
Amplifiers
Mounting
5081 BI
5071 Wall mount (10M+PSU)
5082 FM
5099 DAB
5301 19” Rack frame (10M+PSU)
5087 S Low band
5072 Lockable cabinet (10M+PSU)
5083 BIII
5088 S High band
5089 Hyperband
Various
5086 UHF multichannel DTT
4221 Current injector
5098 UHF High selectivity
5074 F connector Link push fit type
5080 Satellite IF
4061 F type 75 ohms load DC blocked
5073 Blank plate
4071 F type DC blocker terminal load
4058 F type DC 75 ohms load
p 5082
References 5081 5082 5083 5085 5086 5087 5088 5089

Bandwidth 7 20.5 7 32 16/24/32/40 7 7 8
MHz
Frequency range 47-88 87.5-108 174-230 830-862 470-862(1) / 470-862(2) 104-174 230-300 302-470
Gain dB 50 35 50 57 50 58 58 58
Output level dBµV 123 114 123 106 111/109/108/108 125 124 125
Standard EN 50083-5
Noise figure <9 <8 <9
Regulation margin 35 35 35 30
dB
Rejection between channels 40 (n±2) 30(3) 30 (n±2) 22 (ch.65) 20 (ch.65) 30 (n±2) 30 (n±2) 30 (n±2)
Flatness <1 <3 <1 <3 <3 <1 <1 <1
Consumption at 24 Vdc mA 65 90 70 90
Preamp. max. current (24Vdc) mA 100
Dimensions mm 35x197x83
References 5098 5099

Bandwidth 8 37
MHz
Frequency range 470-862 195-232
Gain dB 55 45
Output level dBµV 125/118(4) 114
Standard EN 50083-5 di=50dB (2ch 4MHz)
Noise figure <11 <9
Regulation margin 30 35
AGC margin - -
dB
18 (n±1)
Rejection between channels 20 (n±2)
50 (n±2)
Flatness <2 <3
Consumption at 24 Vdc 90 (1)
2, 3 or 4 UHF channels
mA (2)
5 UHF channels
Preamp. max. current (24Vdc) 100 (3)
Rejection at 77 (MHz) and 120 (MHz)
Dimensions mm 35x197x83 (4)
Analogue/Digital
ELECTRONICS
T03 HEADEND EQUIPMENT
T03. Single Channel Amplification
References 5080
Inputs/outputs 2-1
SAT IF
Frequency range MHz 950-2150
Gain 35···50
Equaliser dB 0-12
Attenuator 0-20
Output level
dBµV 124
DIN VDE0855/12
Noise figure dB <12.5

MATV
Frequency range MHz 47-862
Through losses dB 1.5
General
Consumption (24 Vdc) 130
mA
LNB Power supply 400
p 5080
T YPICAL APPLICATION
ELECTRONICS
T0X HEANDEND EQUIPMENT
T.0X: Logical Evolution

Televes pioneered the creation of the first compact indoor DVB-S2 and DVB-T standards are leaving way to new
unit for the reception, demodulation and transmodulation systems, fruit of the unstoppable technological progress in
to PAL of TVSAT channels. the transmission of audiovisual content.
In the 80s, SAT90 was the first of a series that marked the
birth of the PAL satellite distribution.
This evolution is the one that carried Televes to create T.0X:
His next release, SAT92, lived the rise of this new technology modules ready for new systems such as DVB-T2 or DVB-C2
and the TVSAT implementationas a complement to the and, as SAT90, are called to be
terrestrial distribution. a reference in the sector.
The microprocessors implementation in these kind of devi-
ces, led to the birth of STAR93 and STAR94 in the early 90's.
With the T.0X begins a
The TVSAT signal digitalization came in the second mid 90's. new era of headens
It was when the T05 series was born with QPSK to PAL and equipment.
QAM solutions. The evolution towards new standards and to
HD, made possible the design of modules compatible with
DVB-S2 and DVB-T.
After the first decade of the XXI century, it is necessary a new
evolution in the concept of transmodulators. The implanted
SMATV MATV
Modules that receive the TVSAT signal, transmodulate it to Modules that process terrestrial signal or base-
different formats depending on the network band signal (A/V or ASI).
topology distribution: PAL, DVB-T and DVB-C.
The first ones enable transmodulation or
The digital T.0X modules (COFDM and QAM) are DVB-T signal processing in order to set the
capable of receiving DVB-S2 signals, enabling the multiplexes on demand.
facility site to provide content in high definition
The latter, transform base-band signals into
(HDTV).
self-produced channels to mix them with the
The COFDM modules have an automatic detection other services present in SMATV network.
system of the input signal, allowing a better setting
and programming performance.
The installer can set the output signal format to
the requirements of the network at issue.
In the adjustment phase, the modules generate 45% less 33% less
information on the quality of the input signal, the- consumption consumption
digital output modules also provide information in PAL in QAM
about the occupation state of the output signal. distributions distributions
ELECTRONICS
T0X HEANDEND EQUIPMENT. SMATV
DVB-S2 / COFDM T.0X

PRODUCT RANGE
REF. DESCRIPTION
563101 DVB-S2 COFDM

563301 DVB-S2 COFDM CI
The DVB-S2 transmodulator to COFDM receives a satellite trans-

ponder in some DVBS (QPSK) or DVBS2 (QPSK or 8PSK) modula-
tion formats and demodulates it by obtaining an MPEG-2 trans-
port package. The TS is then modulated in COFDM format and
converted to the output channel (UHF or VHF).
u TS settings in order to comply with DVB-T requirements:

u Stuffing, to perform faster scanning in the STB or when using
STB with a fixed symbol rate.
u MUX services removing to avoid STB detection/loading
u Configurable TS identifier in the NIT. It is possible to substitute
the satellite descriptor for the DTT descriptor allowing a better
STB service detection
u Occupation per service and of the complete MUX COFDM, allo-
wing output space optimization.
u LCN (Logical Channel Number) setting to facilitate the sorting of
the services in the STB.
p 563101
References 563101 / 563301

Input frequency 950-2150 MHz Through loss <1,5 dB typ.
Symbol rate 10-30 Mbaud (QPSK-8PSK) Modulation DVB-S2 (QPSK, 8PSK) DVB-S (QPSK)
LDPC (9/10, 8/9, 5/6, 4/5, 3/4, 2/3,
Frequency steps 1 MHz Internal FEC
Satellite 3/5, 1/2, 1/4, 1/3, 2/5
Demodulator
Input connectors and output “F” female External FEC BCH (Bose-chaudhuri-hocquenghem)
Input impendance 75 ohm Roll-off factor 20%, 25%, 35%
LNB power supply 13/17V/OFF 22 Khz (ON/OFF) Input VSWR 10 dB min.
Modulation format QPSK, 16QAM, 64QAM Scrambling DVB ET300744
COFDM Guard Interval 1/4, 1/8, 1/16, 1/32 Interleaving DVB ET300744
Modulator FEC 1/2, 2/3, 3/4, 5/6, 7,8 Cell_id Selectable
Bandwidth 7 MHz, 8 MHz Output spectrum Normal /Inverted (Select)
Output frequency 45-862 MHz / 474-858 MHz (UHF) Through loss <1,5 dB typ.
Frequency steps 166 KHz Return loss >12 dB typ.
RF Output
Maximum output level 80±5 dBµV (prog.) Input and output connectors “F” female
Attenuation >15 dB (prog.) Output impedance 75 ohm
Power supply 24 V
General Protection index IP20
Comsuption 24 V 300 mA
ELECTRONICS
DVB-S2 / QAM T.0X

PRODUCT RANGE
REF. DESCRIPTION
5630 DVB-S2 QAM TWIN

563501 DVB-S2 QAM CI
The TWIN DVBS2 to QAM unit consists of two transmodulator refe-

rred to as modules A and B. Each module receives a satellite trans-
ponder signal (DVB-S2 standard: QPSK or 8PSK) and demodulates
it to obtain a MPEG2 transport packet. The TS is then modulated
in QAM format and sent to the output channel (UHF or VHF).

u MUX services removing to avoid STB detection/loading.
u Configurable TS identifier in the NIT. It is possible to substitute
the satellite descriptor for the DTT descriptor allowing a better
STB service detection.
u It is possible to replace the operator_id field received in the input
transport stream with a value corresponding to the cable net-
work operator.
u Occupation per service and of the complete MUX QAM, allowing
output space optimization.
p 5630
References 5630 / 563501

Input frequency 950-2150 MHz Modulation DVB-S2 (QPSK, 8PSK) / DVB-S (QPSK)
2 to 42.5 Mbaud (DVB-S)
Input level 49 to 84 dBµV (-60 to -25 dBm) Symbol Rate
10-30 Mbaud (DVB-S2)
Frequency steps 1 MHz FEC Input LDPC (9/10, 8/9, 5/6, 4/5, 3/4, 2/3, 3/5, 1/2)
Satellite
Demodulator Input connectors and output “F” female FEC Output BCH (Bose-chaudhuri-hocquenghem)
Input impendance 75 ohm Roll-off factor 20%, 25%, 35%
LNB power supply 13/17V/OFF 22 Khz (ON/OFF)
Return Losses 10 dB min.
Throughput Losses: < 1,5 dB typ.
Modulation format 16, 32, 64, 128, 256 QAM Scrambling DVB ET300429
QAM Symbol Rate 6,9 Mbaud max Interleaving DVB ET300429
Modulator Roll-Off Factor 15% Bandwidth 8 MHz max.
Block Code Reed Solomon (188, 204) Spectral inversion: Normal /Inverted (Select)
Output frequency 45-862 MHz (Select.) Through loss <1,5 dB typ.
Frequency steps 250 KHz Return loss >12 dB typ.
UP Converter Phase Noise 90 dBc/Hz @10KHz typ Input and output connectors “F” female
Output level 80 ±5 dBµV Output impedance 75 ohm
Adjustable Output level >15 dB (prog.) Spurious level:
Power supply 24 V 550 mA typ. (without powering LNB)
General Comsuption 24 V
Protection index IP20 800 mA typ. (powering LNB)
ELECTRONICS
QPSK/PAL CI TWIN T.0X

PRODUCT RANGE
REF. DESCRIPTION
5537 QPSK-PAL TWIN CI STEREO
The TWIN QPSK-PAL CI allows the user to trasmodulate two chan-

nels (TV or radio) selected from those in two satellite transpon-
ders (same band and polarisation), into two VHF/UHF PAL chan-
nels, with the possibility of stereo modulation.
u The unit allows access to scrambled services by using a conditio-

nal access module (CAM) that performs the service’s descram-
bling.
u Two 3.5 mm jack connectors that make available in baseband
the two audio & video channels of each module.
u IF loop-through for the input connectors on the top of its front,
in order to enable the passage of the input signal to other modu-
les.
u RF loop-through for the output connectors on the bottom of its
front, in order to mix the channels for further amplifi cation.
p 5537
References 5537
13/17V (±0.5 V) / OFF Input VSWR (75 ohm) > 7 dB (950 - 2150 MHz)
LNB Powering (1unit)
22KHz (±2KHz) (Select. ON/OFF) Input symbol rate 2 - 42,5 Mbaud
Input throgh losses < 1.5 dB (950-2150 MHz) Capture range ± 960 ppm
QPSK Input frequency 950 - 2150 MHz Roll-off factor 35%

Demodulator Frequency steps 1 MHz Convolutional code 1/2, 2/3, 3/4, 5/6, 7/8
± 1 MHz (<5 Mbaud) Descrambling
Locking margin ± 2 MHz (5-10 Mbaud) ETS300421
± 5 MHz (>10 Mbaud) Deinterleaving
Input level 44 to 84 dBµV (-65 to -25 dBm) Block code RS(204,188)
Input 1 format MPEG-1 Chrominance format: 4:2:0
Decoding ISO/IEC 11172-2 Video resolution Max. 720 x 576
MPEG-2 Input 2 format MPEG-2 WSS signalling Active
Video decoders Decoding ISO/IEC 13818-2 (MP@ML) Subtitle insertion PAL: Active
TS input rate Max. 90 Mbits/seg
Base band video output: Jack 2,5 mm.
Video rate 1.5 to 15 Mbits/seg
MPEG-2 Input format MPEG-1, MPEG-2
Audio output Stereo, Dual
Audio decoders Decoding LAYER 1, LAYER 2
Output frequency 46- 862 MHz VSWR Output (75 ohm): 10 dB min. 14 dB typ.
Frequency steps 250 KHz Through losses: < 1.5 dB (46-862 MHz)
RF Output
Maximum output level 80 ±5 dBµV
Spurious band level: 55 dBc min. >60 dBc typ.
Attenuation >15 dB
24V : 550 mA typ., no CAM inserted; 24V: 590 mA typ.,CAM inserted (LNB power OFF)
Consumption
General 24V : 755 mA typ., no CAM inserted; 24V : 810 mA typ., CAM inserted (LNB power ON)
Protection index IP20
ELECTRONICS
SMATV APPLICATION
5629 5559
6 x 563101
QPSK input, 6 COFDM channels output. p 563101
QPSK Input
Output
5629 5559
6 x 5537
5629 5575
6 x 5537
QPSK input, 24 PAL channels output. p 5537
ELECTRONICS
T0X HEANDEND EQUIPMENT. MATV
COFDM/COFDM CI T.0X
PRODUCT RANGE
REF. DESCRIPTION
563401 COFDM-COFDM CI
The COFDM transmodulator to COFDM receives a DTT multiplex

and demodulates it by obtaining an MPEG-2 transport package
which can be edited to remove and/or descramble services. The
TS is then modulated in COFDM format and converted to the out-
put channel (UHF or VHF).

u MUX services removing to avoid STB detection/ loading.
bling.
p 563401
References 563401
77-227 Mhz (VHF)
Input frequency Guard interval 1/4, 1/8, 1/16, 1/32
474-858 Mhz (UHF)
COFDM Connectors input/output ''F'' female Scrambling DVB ET300744

Demodulator Input impedance 75 Ohm Interleaving DVB ET300744
Modulation QPSK, 16 QAM, 64 QAM Input trough losses < 1.5 dB typ
Input FEC 1/2, 2/3, 3/4, 5/6, 7/8 Input VSWR 10dB min.
Modulation QPSK, 16 QAM, 64 QAM Scrambling DVB ET300744
COFDM Guard interval 1/4, 1/8, 1/16, 1/32 Interleaving DVB ET300744
Modulator FEC 1/2, 2/3, 3/4, 5/6, 7/8 Cell_id selectable
Band width 7 Mhz, 8 Mhz Output spectrum Normal/ Inverted (Select.)
Output frequency 45 – 862 Mhz Through losses < 1.5 dB typ
Frequency steps 166 Khz Return losses > 12 dB typ
RF Output
Maximum output level 80 ±5 dBµV (progr.) Connectors input/output 'F'' female
Attenuation >15 dB (progr.) Output impedance 75 Ohm
Consumption 24V/ 320 mA
General
ELECTRONICS
COFDM/QAM CI T.0X
PRODUCT RANGE
REF. DESCRIPTION
563601 COFDM-QAM CI
The COFDM transmodulator to QAM receives a DTT multiplex and

demodulates it by obtaining an MPEG-2 transport package which
can be edited to remove and/or descramble services. The TS is
then modulated in QAM format and converted to the output
channel (UHF or VHF).

u MUX services removing to avoid STB detection/ loading.


bling.
p 563601
References 563601
77-227 Mhz (VHF)
Input frequency Guard interval 1/4, 1/8, 1/16, 1/32
474-858 Mhz (UHF)
COFDM Connectors input/output ''F'' female Scrambling DVB ET300744

Demodulator Input impedance 75 Ohm Interleaving DVB ET300744
Modulation QPSK, 16 QAM, 64 QAM Input trough losses < 1.5 dB typ
Input FEC 1/2, 2/3, 3/4, 5/6, 7/8 Input VSWR 10dB min.
Modulation 16, 32, 64, 128, 256 QAM Scrambling DVB ET300744
QAM Symbol rate 6,9 Mbaud max Interleaving DVB ET300744
Modulator Roll-off factor 15% Band width 8,3 Mhz max.
Block code RS (188,204) Output spectrum Normal/ Inverted (Select.)
Output frequency 45 – 862 Mhz Through losses < 1.5 dB typ
Frequency steps 166 Khz Return losses > 12 dB typ
QAM Output
Maximum output level 80 ±5 dBµV (progr.) Connectors input/output 'F'' female
Attenuation >15 dB (progr.) Output impedance 75 Ohm
Consumption 24 V/ 360 mA - 24 V/ 420 mA (CAM)
General
ELECTRONICS
A/D PROCESSOR TWIN T.0X

PRODUCT RANGE
REF. DESCRIPTION
564901 A/D PROCESSOR TWIN
Analogue & Digital channel processor allowing conversion (diffe-

rent input and output channels) or amplification ( same input and
output channel).
u In conversion mode allows to perform a distribution network of

DTT services.
u In amplifier mode allows to equalize a DTT MUX to adapt the sig-

nal level. SAW filtering gives high selectivity.
p 564901
References 564901 Prog.

Input frequency range MHz 46-862 X
Frequency steps 125, 166 X
KHz
Lock margin ± 500
Input loop-though gain dB 0± 3
Input A/D RF
Filter MHz 7,8 X
Pre-amplifier powering Vdc 0, 12, 24 X
Return losses dB >10
Impedance ohm 75
Output frequency range MHz 46-862 X
Frequency steps KHz 125 (digital), 166 (digital), 250 (analog.) X
Max. output level dBµV 80 typ.
Regulation margin dB 65-80 X
Output A/D RF Spurious level dBc >55
END (Equivalent Noise Degradation) <2
Loop-though loss dB <1,5
Return losses > 12
Impedance ohm 75
Powering Vdc 24
General Consumption mA 350
Protection index IP 20
ELECTRONICS
A/V MODULATOR TWIN T.0X

PRODUCT RANGE
REF. DESCRIPTION
5806 A/V MODULATOR TWIN
Ref. 5806 features two A/V inputs (modules A and B) which

generate two independent output channels. The A/V
inputs for each module are modulated according to the TV
standard in an IF of 38.9 Mhz. The modulated IF signal is
converted to any channel or frequency between 46 and
862 Mhz.
u VSB output
u Audio and video parameters configurable to set the
signal in any standard.
u 9 possible channel tables : CCIR N.Z. Ind, China Taiwan,

Chile M/N, Italy, France, Russia (OIR), Ireland, South Africa,
Poland and Australia.
u Test socket (-30 dB) , located in the upper part of the front
panel.
p 5806
References 5806
Bandwidth 0,00005 ... 5 MHz Differencial phase < 4°
input level (75 ohm) 1 Vpp Chroma/luma Delay < 100 ns
Video
Modulation depth 72,5 ... 90 % Chroma/luma Delay > 52 dB
Differencial gain <4% Flatness < +1 dB
Bandwidth 0,04 ... 15 KHz S/N Ratio > 45 dB
Impedance 10000 ohm Flatness < ±1 dB
Audio
Pre-emphasis 0 µS Input level >-15 <7 dBm
Deviation (1KHz/1.7Vpp input) program. (see table) Distortion (1KHz dev. ± 30KHz) < 1 %
Output frequency 46 ... 862 MHz Return loss 10 dB (14 typ)
Impedance 75 ohm.) VHF < 25 KHz
Audio carrier precision
Output level 80 ± 5 dBµV UHF < 50 KHz
Regulation margin > 15 dB VHF < 15 KHz
Video carrier precision
RF Output Level stability ± 3 dB UHF < 30 KHz
Pa/Pv distance -12, -16 (prog.) Carrier ratio (MHz): 4,5 / 5,5 / 6 / 6,5
IF Frequency 38,9 MHz Band spurious level
55 dBc min. > 60 dBc typ
Frequency steps 250 KHz (prog.) 46 ... 862MHz:
C/N (5 MHz) > 56 dB Through losses (46 - 862 MHz): < 1.5 dB
Power supply 24 V
General Protection index IP20
Comsuption 24 V 300 mA
ELECTRONICS
T0X HEANDEND EQUIPMENT. CDC
CDC IP/GPRS T.0X

PRODUCT RANGE
REF. DESCRIPTION
5559 CDC IP
555901 CDC IP GSM/GPRS
Device that allows remote control and monitoring of a T.0X

Televes headend. Ref. 5559 uses a 10/100 Mbps ethernet interface
and Ref. 555901 has a GSM/GPRS internal modem.
u Headend's management and monitoring uses a centralize

system '' Televes Services ''. The portal is located in our headquar-
ters. Access is granted previous identification.
u Built-in RISC Micro under GNU/Linux OS assures 100% reliability

when managing external interfaces end protocols.
p 5559/555901
References 5559/555901
Operating system Linux Kernel 2.6.16
Firmware Boot manager U-boot 1.1.3.
File system jffs2
GSM 850/900
Frequency DCS 1.800
PCS 1.900
MHz EGSM 80
GSM 150
Bandwidth
DCS 170
Radio GSM/GPRS
PCS 140
(only ref. 555901)
GSM +33
Transmission power DCS +30
PCS +30
dBm
GSM -107
Hardware
Sensitivity DCS -106
PCS -106
CPU AT91RM9200
Flash 8
Memory SD RAM MB 64
NAND Flash 128 X 8bit
USB 2.0 Full Speed Host (12 Mbps)
RJ45 1 Ethernet 10/100 Base-T
Connexions RJ45 2 Remote PCT-5.0
SIM Card reader
F (only ref. 555901) Antenna GSM/GPRS (only ref. 555901)
Powering Vdc 24
General Consumption mA 220 (ref. 5559) / 292 (ref. 555901)
Protection Index IP 20
ELECTRONICS
T0X HEANDEND EQUIPMENT
MATV APPLICATION
COFDM input channels
5629 5559
6 x 563401
5629 7 x 563401
20 COFDM
channels output
5559 5575
6 x 563401
COFDM channels input, 20 COFDM channels output. p 563401
ELECTRONICS
MATV APPLICATION
Entrada canales
COFDM
5629 5559
6 x 563601
5629 7 x 563601
17 QAM
channels output
COFDM channels input, 17 QAM channels output. p 563401
ELECTRONICS
T05 HEANDEND EQUIPMENT
CDC system
PRODUCT RANGE
Re f . De SCRIPTION
5059 Headend controller CDC
System accessories
502905 PSU
5075 Hybrid amplifier MATV
2168 PC programming Sw. + Accs.
5837 Modem IP
Mounting & accessories
5069 Lockable cabinet (14M+PSU) p 5059
5073 Blank plate The headend controller allows remote control of a headend by
4061 F type 75 ohms load DC blocked using an external modem connected to the phone line or local con-
trol by connecting a PC directly to the headend controller.
References 5059
The offered services are:
Devices management
Remote programming of devices.
Max. number of devices in the bus 254
Bus control RS485, 3 thread
Headend’s state monitorization
OSD Management Upload the configuration of the headend from a PC.
Headend information screen 4 screen max. Generate a private TV channel.
Programmable data screen 4 screen max. State screen information of the headend devices.
Delay between sreens programmable
Modem connection
External modem serie, compatible AT 9600 baud
Transmition speed 9600 baud
RF VSB Output
Output frequency MHz 46-862 (or list of channels)
Frequency steps kHz 250
Max. output level dBµV 80±5 (programmable)
Regulation margin 15
USWR Output dB 14 typ.
Bypass losses <1.5
Spurious dBc 60 typ.
TV standard PAL / NTSC
General
Consumption A (Vdc) 0.6 (5); 0.2 (15) Device management CDC
ELECTRONICS
REMOTE HEADEND CONTROLLER
CDC System – Modem
PRODUCT RANGE
Re f . De SCRIPTION
5837 IP Modem
5836 GSM Modem
References 5837
Serial Interface RS232 (TX/RX)
Routing Buffer 12 Kbytes x 2
Ethernet Connection 10/100 BaseT
CDC Communication RJ45 (RS232, TX/RX) p 5837
Consumption (5V) mA 500
Satellite input Terrestrial input
TDT QPSK-PAL QPSK-PAL QPSK-PAL QPSK-PAL QOFDM-PAL QOFDM-PAL QOFDM-PAL

CDC MODEM
Direc. 1 Direc. 2 Direc. 3 Direc. 4 Direc. 5 Direc. 6 Direc. 7 Direc. 8 Direc. 9 Direc. 10 Direc. 0
Headend local connection

RS485 Control Bus
Modem Telephone line
headend remote connection
ELECTRONICS
A/V - COFDM Modulator

PRODUCT RANGE
Re f . De SCRIPTION
5540 ASI - COFDM

5541 MPEG-2 QUAD encoder
Generates a DTT multiplex (COFDM) from 4 analogue A/V signals.
p 5541 p 5540
Reference 5540 Adapts analogue signals to DTT receiver/tv sets.

Standard EN 50083-9 Control of the input signals degree of compression using the MPEG2
Bandwidth MHz 7-8 encoder (ref. 5541).
COFDM Modulation QPSK, 16QAM O 16 QAM
The A/V inputs are fully independent, allowing for different degrees of
Modulation IG 1/4, 1/8, 1/16, 1/32
µS quality depending on the service (sports, news, etc)
FEC 1/2, 2/3, 3/4, 5/6, 7/8
Locally (front panel) or remotely (IP protocol) configurable.
Frequency MHz 117,5-226,5 / 474-858
Output
Offset KHz 125 - 166 All-band output.
Powering Vdc 5 - 15 - 18
Power Supply
Consumption mA 350(5V)-175(15V)-70 (18V) T YPICAL APPLICATION
A/V1 A/V2 A/V3 A/V4

Reference 5541 Ref. 5541
ISO/ICE11172 5541 - MPEG QUAD ENCODER
Standard
ENTER MENU LOCK
POWER ALARM
Ref. 5540
ISO/ICE13818
Codification MPEG-2 MP@ML (4:2:0)
ASI- COFDM
Video Input CVBS, S-VIDEO

Bit Rate Mbps 1,5 - 15
Codification MPEG-1 Layer 1
Audio 6
S.R. KHz 32, 44.1, 48
LCD + frontal keyboard 5
Control
Remote control SMNP
ASI Bit Rate Mbps 170
MPEG Output 1
Package 188/204
Powering Vac 90-260 R/C
Power Supply
Consumption W 350(5V)-175(15V)-70 (18V)
ELECTRONICS
A/V - COFDM Modulator

Application example where 4 A/V analogue sources (cameras,
DVD players...) are converted to a DTT multiplex that is then
mixed with two additional TVSAT content multiplexes (DVB/S2-
COFDM transmodulator ref. 5181).
These three COFDM multiplexes are amplified with T03 units
and then mixed with the DTT signal received in the antenna
resulting in a headend that permits the reception of analogue
services and digital satellite contents in our DTT adapters/recei-
vers.
A/V1 A/V2 A/V3 A/V4
ASI-out
5541 - MPEG QUAD ENCODER
ENTER MENU LOCK

POWER ALARM
SAT
TS proc TS proc ASI- COFDM
UHF
Output
ELECTRONICS
Analogue / Digital Channel Processor

PRODUCT RANGE
References 5179
Re f . De SCRIPTION
Input
5179 A/D Channel Processor
Input frequency range MHz 46...862
D:166.66/125
Frequency steps KHz
System accessories A:250
Input level dBµV 50-82 (AGC)
502905 PSU Input loop-through loss dB 0±3
5075 Hybrid amplifier MATV Output
2168 PC programming Sw. + Accs. Output frequency range MHz 46...862
7234 Universal Programming Unit D:166.66/125
Frequency steps KHz
5837 Modem IP A: 250
Mounting & accessories Max. output level dBµV 80±5
5071 Wall mount (10M+PSU) Regulation margin 15

Return loss >10
Slope adjustment ±3
5301 19” Rack frame (10M+PSU) dB
Output Loop-through loss <1.5
Equivalent noise
5069 Lockable cabinet (14M+PSU) <2
degradation (END)
General
5073 Blank plate
Consumption mA (Vdc) 500 (5); 150 (15)
Preamplifier power Vdc 12/24 (UHF in)
p 5179
Analogue & digital channel pro-

cessor allowing the conversion T YPICAL APPLICATION
or just processing of both digital
& analogue channels. Fully
input/output agile through the
full VHF & UHF band. The pro-
duct can also be used as chan-
nel processor using same
input/output channel. The
input AGC guarantees a stable
output level.
Programmable parameters:
• Freq./Channel (Input / output).
• Output level
• Converter/Amplifier
• Channel slope.
• Analogue/Digital mode.
• Input bandwidth 7/8 MHz
• Remotely controllable via CDC
ELECTRONICS
COFDM-PAL CONTROL MODE

via modem PC
PRODUCT RANGE References 505403 / 504403

Re f . De SCRIPTION COFDM demodulator
Input through losses dB 1,2
505403 COFDM-PAL 174-230 / 474-858
Input frequency
504403 COFDM-PAL stereo (or channel tables)
MHz
Frequency steps 1
Locking margin ±3
49 to 89
Input level dBµV
System accessories (8k; 64 QAM;FEC 2/3)
Return losses dB >12 (46-862 MHz)
502905 PSU Bandwidth filter SAW MHz 7 - 8 programmable
5075 Hybrid amplifier MATV FFT 2k; 8k
2168 PC programming Sw. + Accs. Constellation QPSK; 16QAM; 64 QAM
Guard interval 1/4; 1/8; 1/16; 1/32
Viterbi rate 1/2; 2/3; 3/4; 5/6; 7/8
5837 Modem IP Max. symbol rate Mbaud 31.67
Mounting & accessories MPEG Decoder
Input format TS MPEG-2/DVB
Decoding MP@ML
5239 Wall mount (12M+PSU) TS input rate 60 max.
Mbps
5301 19” Rack frame (10M+PSU) Video rate 1.5 to 15
Video resolution Max. 720x576
Video output composite PAL
5069 Lockable cabinet (14M+PSU) RF VSB Output
5235 Lockable cabinet (22M+PSU) Output frequency MHz 46-862 (or channel tables)
5073 Blank plate Frequency steps KHz 250
Max. Output level dBµV 80±5 p 505403
Variable gain 15
Return losses dB 14 typ.
Through losses <1.5
Spurious band level dBc 60 typ.
General
Consumption A (Vdc) 1.2 (5) / 0.4 (15)
Preamplifier PSU mA 50 (0-12-24Vdc, prog.)
Transforms a terrestrial digital chan- T YPICAL APPLICATION

nel to an analogue channel either in
VHF or UHF.
Programmables parameters:
• Input and output channel.
• Output level.
• Video and Audio program selection.
• Video modulation index.
• Audio deviation.
• Audio carrier frequency.
• A/V ratio
• Remotely controllable via the CDC.
ELECTRONICS
COFDM-PAL CI CONTROL MODE

via modem PC
PRODUCT RANGE References 5544
Re f . De SCRIPTION COFDM demodulator
Input through losses dB 1,2
5544 COFDM-PAL CI 174-230 / 474-858
Input frequency
(or channel tables)
MHz
Frequency steps 1
Locking margin ±3
Main features 49 to 89
Input level dBµV
(8k; 64 QAM;FEC 2/3)
• Transmodulator with slot for CAM Return losses dB >12 (46-862 MHz)
module. Bandwidth filter SAW MHz 7 - 8 programmable
• Generates an analogue channel FFT 2k; 8k
from a scrambled MPEG2 DVBT Constellation QPSK; 16QAM; 64 QAM
service. Guard interval 1/4; 1/8; 1/16; 1/32
• The generated channel is single Viterbi rate 1/2; 2/3; 3/4; 5/6; 7/8
side band, allowing the configu- Max. symbol rate Mbaud 31.67
ration of adjacent channels MPEG Decoder
within 46 and 862 MHz. Input format TS MPEG-2/DVB
Decoding MP@ML
• Generates DVB and teletext subti- TS input rate 90 max.
tles. Mbps
Video rate 1.5 to 15
• Both local and remote configura- Video resolution Max. 720x576
tion & control capability. Video output composite PAL
RF VSB Output
• Monitor menu with quality mea- Output frequency MHz 46-862 (or channel tables)
sures (CBER) of the input signal. Frequency steps KHz 250
Max. Output level dBµV 80±5 p 5544
Variable gain 15
Return losses dB 10 min. 14 typ.
Through losses <1.5
Spurious band level dBc 60 typ.
Advantages
General
The COFDM-PAL transmodulator Consumption A (Vdc) 0.7 (5)w/o CAM/0.95 (15)w/CAM
with Common Interface allows to: Preamplifier PSU mA 50 (0-12-24Vdc, prog.)
• Integrate paid-tv services in a
free-tv headend, making both
free and paid DTT compatible T YPICAL APPLICATION
with every television so it is not
necessary to replace the analo- CAM
gue TV sets.
• Used in headend for hotels, hos-
pitals, etc... allows to keep the
current CRT TV sets already ins-
talled.
• Protects of possible robberies of
flat TV sets
• Only one remote control, same TV
and same channel list than befo-
re the analogue switch off. Very
suitable in installations where Ref. 5544
the service is provided to elderly
or handicapped people
ELECTRONICS
IF / IF processors CONTROL MODE

via modem PC
PRODUCT RANGE References 586301 586401

Re f . De SCRIPTION Input freq. margin 950-2150
Output freq. margin MHz 950-2150
586301 Single IF processor DVBS2
Frequency steps 1
586401 Triple IF processor DVBS2 Output impedance W 75
Input return losses >10
dB
Output return losses >10
BW of the selected channel MHz 10 a 72 (2 MHz steps)
System accessories
Input level 60 - 88
dBµV
502905 PSU Output level 75±5
5075 Hybrid amplifier MATV

Level regulator Yes
13/17 / OFF
2168 PC programming Sw. + Accs. Powering LNB Vdc
22 KHz / OFF
General
5837 Modem IP
5V:550 5V:1100
Max. consumption mA
Mounting & accessories 15V:50 15V:50
5071 Wall mount (10M+PSU) Protection index IP 20
IF AMPLIFIER
References 5865
Frequency range MHz 950···2150
5069 Lockable cabinet (14M+PSU) Gain (950 MHz) 35±2
5235 Lockable cabinet (22M+PSU) Gain (2150 MHz) dB 40±3
5073 Blank plate Adjustable margin 20 p 586301
4061 F type 75 ohms load DC blocked Output voltage (2 tones -35dB) dBµV >123
Connector “F”
Powering Vdc 15
Consumption mA(vdc) 200(15)
Programmable parameters:
• Modular and programmable sate-
llite system. B. Alta H
• Allows the selection of any chan- B. Baja V
nel in the IFband to be shifted into B. Alta V
B. Alta V
another channel inside the band.
• Remotely controllable via the Ref. 5437
MATV
CDC.
Salida
MATV + FI
Ref. 586401
Ref. 5865
ELECTRONICS
MATV Hybrid amplifier
PRODUCT RANGE References 5075

Re f . De SCRIPTION Frequency range MHz 47-862
Gain 45±2
5075 MATV Hybrid amplifier dB
Gain regulation 20
DIN 45004-B 120
Hybrid amplifier for headend IMD3 (-60 dB, 2c) 117
equipment. Provided with 2 inputs Output level IMD2 (-60 dB, 2c) 111
to mix its output with channels dBµV
CTB (-60 dB, 42c) 105
comming from different systems.
CSO (-60 dB, 42c) 105
XMOD (-60 dB, 42c) 105
Noise figure dB <10
General
Powering voltage Vdc 15
Consumption A 0.8
p 5075
PSU
PRODUCT RANGE
Re f . De SCRIPTION
502905 Switched PSU T-03/T-05

5030 Switched PSU T-03 / T-05 110 Vac UL
5498 Switched PSU T-03
Switched PSU for the T03 and T05 range.
References 502905 / 5030 * 5498

Mains voltage Vac 230±15
Frequency Hz 50/60
Output voltage Vdc 24 18 15 5 24
Max. output current A 0.55 0.8 4.2 (*) 6.6 2.5
Max. output powering W 13.2 14.4 63 (*) 33 60
Dimensions mm 56x197x163 55x197x83
*24 and/or 18V voltage are obteined from 63W (15V) PSU
p 502905
ELECTRONICS
HEADEND EQUIPMENT
Cabinets and supports

PRODUCT RANGE 5071/5239
Re f . De SCRIPTION
new

5301 19” Rack frame (10M+PSU) p 5071/5239

507202 Lockable cabinet T0X
(7M+PSU) with ventilation Ref.5069
Compatible
p 5750
5334 T03/T05 Ventilation system
5750 Outdoor cabinet p 5334
5331 19” Rack cabinet (30M) + accessories

5332 19” Rack cabinet (40M) + accessories
References 5072 5069 5235 5750

c a 610 760 1060 440
b
b 295 440
a
c 235 140 p 5301
p 5069/5235/5072
Accessories
PRODUCT RANGE
Re f . De SCRIPTION
5073 Blank plate T05

5673 Blank plate T0X
5074 Link F connector
4221 Power injector
7234 Universal programmer p 4947 p 7234
4947 Coaxial surge arrestor
422601 Power lead for T0X with T05 PSU
422602 Data lead for T0X with T05 CDC
p 4061 p 5074
p 4221 p 5073

7234

Uploaded by

Copyright:

Available Formats

7234

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

7234

Uploaded by

Copyright:

Available Formats

CATALOGO internacional 2011:CATALOGO internacional 2010_imprenta.

qxd 27/07/2011 9:38 Página 50

7234 Universal Programming Unit

5 UHF filters and 1 VHF filter p 5326

2 UHF inputs with two possible filter assig-

VHF input that can cluster up to 4 channels

Input loopthru to mix the output of another

Broadband output to another AVANT3

Reference 5326 /5327

General attenuation 0-20 BIII-DAB

T03 HEADEND EQUIPMENT

T03. Single Channel Amplification

References 5081 5082 5083 5085 5086 5087 5088 5089

References 5098 5099

T03 HEADEND EQUIPMENT

T03. Single Channel Amplification

Noise figure dB <12.5

T0X HEANDEND EQUIPMENT

T.0X: Logical Evolution

T0X HEANDEND EQUIPMENT. SMATV

DVB-S2 / COFDM T.0X

563101 DVB-S2 COFDM

The DVB-S2 transmodulator to COFDM receives a satellite trans-

u TS settings in order to comply with DVB-T requirements:

References 563101 / 563301

T0X HEANDEND EQUIPMENT. SMATV

DVB-S2 / QAM T.0X

5630 DVB-S2 QAM TWIN

The TWIN DVBS2 to QAM unit consists of two transmodulator refe-

u TS settings in order to comply with DVB-T requirements:

References 5630 / 563501

T0X HEANDEND EQUIPMENT. SMATV

QPSK/PAL CI TWIN T.0X

5537 QPSK-PAL TWIN CI STEREO

The TWIN QPSK-PAL CI allows the user to trasmodulate two chan-

u The unit allows access to scrambled services by using a conditio-

QPSK Input frequency 950 - 2150 MHz Roll-off factor 35%

T0X HEANDEND EQUIPMENT. SMATV

QPSK input, 6 COFDM channels output. p 563101

QPSK input, 24 PAL channels output. p 5537

T0X HEANDEND EQUIPMENT. MATV

The COFDM transmodulator to COFDM receives a DTT multiplex

u TS settings in order to comply with DVB-T requirements:

COFDM Connectors input/output ''F'' female Scrambling DVB ET300744

T0X HEANDEND EQUIPMENT. MATV

The COFDM transmodulator to QAM receives a DTT multiplex and

u TS settings in order to comply with DVB-T requirements:

u Stuffing, to perform faster scanning in the STB or when using

u LCN (Logical Channel Number) setting to facilitate the sorting of

u The unit allows access to scrambled services by using a conditio-

COFDM Connectors input/output ''F'' female Scrambling DVB ET300744

T0X HEANDEND EQUIPMENT. MATV

A/D PROCESSOR TWIN T.0X

564901 A/D PROCESSOR TWIN

Analogue & Digital channel processor allowing conversion (diffe-

u In conversion mode allows to perform a distribution network of

u In amplifier mode allows to equalize a DTT MUX to adapt the sig-

References 564901 Prog.

T0X HEANDEND EQUIPMENT. MATV