Amateur - IC-T70A Instruction Manual PDF

INSTRUCTION MANUAL
VHF/UHF DUAL BAND FM TRANSCEIVER
iT70A
iT70E
This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CEL-
LULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED
UNDER FCC RULES AND FEDERAL LAW.
FOREWORD FEATURES
Thank you for purchasing this fine Icom product. The IC- ❍ Dust-protection/Splash-resistant construc-
T70A/T70E vhf/uhf dual band fm transceiver is designed
and build with Icom’s superior technology and craftsmanship. tion (IP54*)
With proper care, this product should provide you with years *Only when the battery pack/case, antenna and jack cover
of trouble-free operation. are attached.
We want to take a moment of your time to thank you for mak- ❍ Built in VOX circuit enabling the VOX opera-
ing your IC-T70A/T70E your radio of choice, and hope you
agree with Icom’s philosophy of “technology first.” Many hours tion* (voice operated transmission)
or research and development went into the design of your *To use the VOX operation, an optional headset and a plug
IC-T70A/T70E. adapter cable are additionally required.
❍7
00 mW* AF power with BTL (bridge-tied
EXPLICIT DEFINITIONS load) amplifier
*At 10% distortion with a 16 Ω load (internal speaker)
WORD DEFINITION
R DANGER!
Personal death, serious injury or an ex-
plosion may occur.
IMPORTANT
READ ALL INSTRUCTIONS carefully and completely
Personal injury, fire hazard or electric
R WARNING! before using the transceiver.
shock may occur.
CAUTION Equipment damage may occur. SAVE THIS INSTRUCTION MANUAL— This
Recommended for optimum use. No risk instruction manual contains important operating instructions
NOTE
of personal injury, fire or electric shock. for the IC-T70A/T70E.

PRECAUTIONS
R WARNING RF EXPOSURE! This device emits NEVER connect the transceiver to a power source of more
Radio Frequency (RF) energy. Caution should be observed than 16 V DC. This will ruin the transceiver.
when operating this device. If you have any questions regard-
ing RF exposure and safety standards please refer to the NEVER connect the transceiver to a power source using
Federal Communications Commission Office of Engineering reverse polarity. This will ruin the transceiver.
and Technology’s report on Evaluating Compliance with FCC
DO NOT operate the transceiver near unshielded electri-
Guidelines for Human Radio Frequency Electromagnetic
cal blasting caps or in an explosive atmosphere.
Fields (OET Bulletin 65)
DO NOT push the PTT unless you actually intend to trans-
R WARNING! NEVER hold the transceiver so that mit.
the antenna is very close to, or touching exposed parts of
the body, especially the face or eyes, while transmitting. The BE CAREFUL! The transceiver will become hot when op-
transceiver will perform best if the microphone is 5 to 10 cm erating it continuously for long periods of time.
(2 to 4 inches) away from the lips and the transceiver is verti-
cal. DO NOT use or place the transceiver in direct sunlight
or in areas with temperatures below –20°C (–4˚F) or above
R WARNING! NEVER operate the transceiver with +60°C (+140˚F).
an earphone, headphones or other audio accessories at high Place the unit in a secure place to avoid inadvertent use by
volume levels. Hearing experts advise against continuous children.
high volume operation. If you experience a ringing in your
ears, reduce the volume level or discontinue use. DO NOT use harsh solvents such as benzine or alcohol to
clean the transceiver, because they can damage the trans-
R WARNING! NEVER operate the transceiver while ceiver’s surfaces.
driving a vehicle. Safe driving requires your full attention—
anything less may result in an accident.
ii
PRECAUTIONS FCC INFORMATION
KEEP the transceiver away from heavy rain, and never im- • FOR CLASS B UNINTENTIONAL RADIATORS:
merse it in the water. The transceiver meets IP54* require- This equipment has been tested and found to comply with the
ments for dust-protection and splash resistance. However, limits for a Class B digital device, pursuant to part 15 of the
once the transceiver has been dropped, dust-protection and FCC Rules. These limits are designed to provide reasonable
splash resistance cannot be guaranteed because of possible protection against harmful interference in a residential instal-
damage to the transceiver’s case or the waterproof seal. lation. This equipment generates, uses and can radiate radio
*Only when the supplied battery pack (or optional battery frequency energy and, if not installed and used in accordance
pack/case), antenna and jack cover are attached. with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that inter-
ference will not occur in a particular installation. If this equip-
NEVER operate or touch the transceiver with wet hands. ment does cause harmful interference to radio or television
This may result in an electric shock or may damage the trans- reception, which can be determined by turning the equipment
ceiver. off and on, the user is encouraged to try to correct the inter-
ference by one or more of the following measures:
Even when the transceiver power is OFF, a slight current still
flows in the circuits. Remove the battery pack or batteries • Reorient or relocate the receiving antenna.
from the transceiver when not using it for a long time. Other- • Increase the separation between the equipment and re-
ceiver.
wise, the installed battery pack or batteries will become ex-
• Connect the equipment into an outlet on a circuit different
hausted, and will need to be recharged or replaced.
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
CAUTION: Changes or modifications to this device, not

expressly approved by Icom Inc., could void your authority
to operate this device under FCC regulations.
iii
SUPPLIED ACCESSORIES 1
2
The following accessories are supplied with the transceiver.
q Hand strap �� 1 3
w Antenna �� 1
4
e Battery pack (BP-264)* �� 1
r Belt clip* ��1 5
t Battery charger (BC-167SA/SD/SV)* �� 1
6
* Not supplied, or the shape is different, depending on the transceiver
version.
7
8
q w e
9
10
11
12
13
14
r t 15
16
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom
Incorporated (Japan) in Japan, the United States, the United King- 17
dom, Germany, France, Spain, Russia and/or other countries.
18
Microsoft, Windows and Windows Vista are registered trademarks of 19
Microsoft Corporation in the United States and/or other countries.
iv
TABLE OF CONTENTS
FOREWORD······················································································ i 4 BASIC OPERATION····························································16–23
EXPLICIT DEFINITIONS···································································· i ■ Power ON···············································································16
FEATURES························································································· i ■ Setting audio volume······························································16
IMPORTANT······················································································· i ■ Setting the squelch level·························································17
PRECAUTIONS·············································································ii–iii ■ Monitor function······································································17
FCC INFORMATION········································································ iii ■ Selecting the mode·································································18
SUPPLIED ACCESSORIES····························································· iv ■ Setting the tuning step····························································19
TABLE OF CONTENTS ······························································· v–vi ■ Setting the frequency······························································19
■ Operating mode selection·······················································21
1 ACCESSORY ATTACHMENT··················································1–2
■ Key lock function·····································································21
■ Hand strap················································································1
■ Receiving················································································22
■ Belt clip·····················································································1
■ Transmit power selection························································22
■ Battery pack··············································································2
■ Transmitting·············································································23
■ Antenna····················································································2
5 REPEATER AND DUPLEX OPERATIONS·························24–28
2 PANEL DESCRIPTION····························································3–8
■ Repeater operation·································································24
■ Front, top and side panels························································3
■ Duplex operation·····································································26
■ Function display········································································6
■ Reverse duplex function·························································26
3 BATTERY CHARGING··························································8–15 ■ Auto repeater function····························································27
■ Caution (for the supplied BP-264 Ni-MH battery pack)·············8 ■ 1750 Hz tone··········································································28
■ Caution (for the optional BP-265 Li-Ion battery pack)···············9
6 MEMORY/CALL CHANNELS··············································29–39
■ Optional battery case······························································11
■ General description································································29
■ Battery information·································································11
■ Selecting a call channel··························································29
■ Regular charging····································································12
■ Selecting a memory channel··················································30
■ Desktop battery chargers·······················································13
■ Memory channel programming···············································31
■ External DC power operation··················································15
■ Memory bank setting······························································32
■ Memory bank selection···························································33
■ Programming memory/bank/scan name·································34

TABLE OF CONTENTS 1
2
■ Selecting memory/bank name indication································35 ■ Tone frequency and DTCS code·············································68
■ Display type············································································36 ■ Tone/DTCS squelch································································70 3
■ Copying memory/call contents···············································37 ■ Tone scan···············································································71
■ Memory clearing·····································································38 ■ Weather channel operation·····················································72
4
■ Erasing/transferring bank contents·········································39 ■ Cloning function······································································74 5
■ Resetting················································································75
7 SCAN OPERATION·····························································40–47 6
■ Scan types··············································································40 11 TROUBLESHOOTING·······························································76
■ Full/band/programmed scan ··················································42 7
12 SPECIFICATIONS······································································77
■ Scan edges programming·······················································43
■ Memory scan ·········································································44
8
13 OPTIONS·············································································78–82
■ Memory bank scan·································································45 ■ VOX function···········································································80 9
■ Skip channel/frequency setting···············································46 ■ Remote control function··························································82
■ Scan resume setting·······························································47 10
14 CE ······················································································83–84
8 PRIORITY WATCH·······························································48–50 11
■ Priority watch types································································48 INDEX ······················································································85–88
■ Priority watch operation··························································49
12
9 SET MODES········································································51–64
13
■ General ···············································································51 14
■ Set mode item list···································································52
■ Initial set mode item list··························································52 15
■ Set mode items·······································································53 16
■ Initial set mode items······························································59
17
10 OTHER FUNCTIONS···························································65–75
■ Programming a DTMF code sequence···································65 18
■ Transmitting a DTMF code sequence·····································66
19
■ Setting DTMF transfer speed··················································67
vi
1 ACCESSORY ATTACHMENT
■ Hand strap ■ Belt clip

To facilitate carrying the To attach the belt clip:
transceiver, slide the hand Slide the belt clip in the
strap through the loop on direction of the arrow
the top of the rear panel as until the belt clip locks in
place, and makes a ‘click’
illustrated at the right.
sound.
Handstrap
To detach the belt clip:

q Remove the battery pack from the transceiver, if it is at-
tached. (p. 2)
w Lift the tab up (q), and slide the belt clip in the direction
of the arrow (w).
w
q

ACCESSORY ATTACHMENT 1
■ Battery pack ■ Antenna 1

To attach the battery pack: Insert the antenna connector into the antenna base and 2
q F it the battery pack Battery pack/Battery case tighten the antenna screw. 3
in the direction of the Jack cover
arrow (q), then close. 4
w Hook the latch until it q 5
makes a ‘click’ sound
(w). 6
• Charge the battery pack w
7
before use. (pp. 12–14)
8
Latch 9
To detach the battery pack: 10
Be careful! The latch is tightly locked, so use caution 11
when releasing it. DO NOT use your finger nail. Use the
edge of a coin or screwdriver tip to carefully release it. •N
EVER carry the transceiver by holding only the an-
12
Unhook the latch (e), Battery pack/Battery case tenna. 13
and lift up the battery •W
hen the jack is not in use, keep the jack cover in place 14
pack in the direction of to protect the connector from dust and moisture.
the arrow (r). 15
r ✔ For your information
h i r d - p a r t y a n t e n n a s m ay i n c r e a s e t ra n s c e i ve r
T 16
p e r fo r m a n c e . A n o p t i o n a l A D - 9 2 S M A a n t e n n a 17
connector adapter is available to connect an antenna
e that has a BNC connector. 18
19
Latch

2 PANEL DESCRIPTION
■ Front, top and side panels

q ANTENNA q ANTENNA CONNECTOR (p. 2)
CONNECTOR Connects to the supplied antenna.
• An optional AD-92SMA adapter (p. 79) is available for connect-
w EXTERNAL SPEAKER/ ing an antenna with a BNC connector.
MICROPHONE JACKS
w E
XTERNAL SPEAKER/MICROPHONE JACKS [SP/MIC]
e CONTROL DIAL Connect an optional speaker microphone, cloning cable,
r VOLUME or headset, if desired.
CONTROL See page 79 for a list of available options.
Speaker Be sure to turn power OFF before connecting or dis-
connecting optional equipment to/from the [SP/MIC]
t PTT SWITCH jack.
y EXTERNAL
DC IN JACK e CONTROL DIAL [DIAL]
➥ Rotate to select the operating frequency. (p. 19)
Internal microphone ➥ During memory mode operation, rotate to select the
memory channel. (pp. 18, 30)
Function display (pp. 6, 7) ➥ W hile scanning, changes the scanning direction.
(pp. 42, 44, 45)
➥ While continuing to push [MONI](BAND), sets the
squelch level. (p. 17)
Keypad (pp. 4, 5) ➥ After pushing [BAND] during memory mode operation,
selects the programmed bank. (p. 33)
➥ During set mode operation, rotate to select the set
items. (p. 51)

PANEL DESCRIPTION 2
D Keypad 1
r VOLUME CONTROL [VOL] 2
➥ Adjust the audio volume level. (p. 16) 3
➥ During set mode operation, rotate to select the options.
(p. 51) 4
t PTT SWITCH [PTT] 5
➥ Push and hold to transmit, release to receive. (p. 23) 6
For IC-T70E only 7
➥ Push briefly, then push and hold to transmit a 1750 Hz ➥ Push to input numbers for frequency input or memory
tone burst. (p. 28) channel selection. 8
➥ While continuing to push [PTT], push the key to send the
y EXTERNAL DC IN JACK [DC IN] DTMF code. (pp. 66, 67) 9
➥ Connects the supplied wall charger, BC-167S, to charge • [ 0]–[9] send “0”–“9,” [A](SET) sends “A,” [B](BAND) sends “B,”
the attached battery pack, BP-264. (p. 12)
10
[C](H/M/L) sends “C,” [D](V/M/C) sends “D,” [M](DUP) sends
• The transceiver can charge only the BP-264 Ni-MH battery “M (E)” and [#](T.SCAN) sends “# (F).” 11
pack. Charging the BP-265 Li-Ion battery pack requires the
BC-193 desktop charger. POWER KEY [ ] 12
➥ Connect an external DC power supply through the op- ➥ Push and hold for 1 sec. to turn the transceiver 13
tional CP-12L, CP-19R or OPC-254L for external DC power ON or OFF. (p. 16)
operation. (p. 15) 14
VFO/MEMORY/CALL • SELECT MEMORY WRITE KEY
[V/M/C] • [S.MW](V/M/C)
15
➥ Push to select the VFO mode, memory mode, call 16
channel mode or weather channel mode*. (pp. 18,
29, 30, 72)
17
*Only for the U.S.A. version transceiver. 18
➥ Push and hold for 1 sec. to enter select memory
write mode. (p. 31) 19

2 PANEL DESCRIPTION
D Keypad (continued)
OUTPUT POWER • SCAN KEY [H/M/L] • [SCAN](H/M/L) TONE SCAN KEY [T.SCAN](#)
➥ Push to select the output power. (p. 22) ➥ Push and hold for 1 sec. to start the tone scan
• Selects the transmit output power from high, middle function. (p. 71)
or low.
TONE/TONE SQUELCH KEY [TONE](0)
➥ Push and hold for 1 sec. to enter the scan type
➥ Push and hold for 1 sec. to select sequentially
selection mode. (pp. 42, 44, 45)
repeater tone, tone squelch, tone squelch re-
• Push again to start the scan.
verse, DTCS squelch, DTCS squelch reverse and
BAND • MONITOR KEY [BAND] • [MONI](BAND) no tone operation. (p. 70)
➥ During VFO mode operation, push to select an • The pocket beep function is available with tone squelch
operating frequency band. (p. 19) and DTCS squelch. (p. 70)
➥ Push and hold to open the squelch temporarily
and monitor the operating frequency. (p. 17) DUPLEX KEY [DUP](M)
➥ While continuing to push this key, rotate [DIAL] to ➥ Push and hold for 1 sec. to select minus duplex,
adjust the squelch level. (p. 17) plus duplex or simplex operation. (p. 26)
➥ During memory mode operation, push to enter the • “DUP–” (minus duplex), “DUP” (plus duplex) and no
memory bank group selection. (p. 33) indication (simplex) appear in order.
SET • LOCK KEY [SET] • [ ](SET)

➥ Push to enter the Set mode. (p. 51)
➥ Push and hold for 1 sec. to toggle the lock func-
tion ON or OFF. (p. 21)
➥ During select memory write mode, push to select
the items. (pp. 32, 34, 38, 39)

PANEL DESCRIPTION 2
■ Function display 1
q w e r ty w DUPLEX ICON (p. 26) 2
“DUP” appears when plus duplex is selected, “DUP–” ap- 3
pears when minus duplex is selected.
e TONE ICON 4
➥ “T” appears while the subaudible tone encoder is in 5
use. (p. 24)
➥ “T SQL” appears while the tone squelch function is in 6
use. (p. 70) 7
➥ “T SQL-R” appears while the reverse tone squelch func-
tion is in use. (p. 70) 8
➥ “DTCS” appears while the DTCS squelch function is in 9
q BATTERY ICON (pp. 11, 12) use. (p. 70)
m When the BP-264 or BP-265 is attached ➥ “DTCS -R” appears while the reverse DTCS squelch 10
➥ “ ” (battery icons) appear when the battery pack function is in use. (p. 70)
has ample capacity. ➥ “S” appears with the “T SQL” or “DTCS” indicator
11
➥ “ ” appears when the battery pack has less than while the pocket beep function (with CTCSS or DTCS) 12
half capacity. is in use. (p. 70)
➥ “ ” blinks before the battery pack is exhausted. 13
r VOX ICON (p. 80)
The battery pack must be charged. Appears when the VOX function is in use. 14
➥ The icons show “ ,” “ ” and “ (disappears)”
in sequence while charging the BP-264 Ni-MH bat- t AUTO POWER OFF ICON (p. 59) 15
tery pack. Appears when the Auto Power OFF function is ON.
16
y KEY LOCK ICON (p. 21)
m When the BP-263 is attached 17
Appears when the key lock function is activated.
➥ “ ” (battery icons) appear when the batteries have
ample capacity. 18
➥ “ ” blinks before the batteries are exhausted. The
19
batteries must be replaced.

2 PANEL DESCRIPTION
■ Function display (continued)

!1 WEATHER CHANNEL ICON (pp. 72–73)
!6 Appears when the weather alert function is in use.
u !2 S/RF METER
i ➥ Shows the relative signal strength while receiving sig-
!5 o nals. (p. 22)
➥ Shows the output power level while transmitting.
(pp. 22, 23)
!3 OPERATING MODE ICONS (p. 21)
!4 !3 !2 !1 !0 Shows the selected operating mode.
• FM and FMN are selectable.
u SKIP ICONS !4 POWER ICONS (p. 22)
➥ “ ” appears when the selected memory channel is ➥ “L” appears when low power is selected.
set as a skip channel. (p. 46) ➥ “M” appears when middle power is selected.
➥ “P ” appears when the displayed frequency is set ➥ No indicator appears when high power is selected.
as a skip frequency in memory mode. (p. 46)
!5 FREQUENCY READOUT
i MEMORY ICON (pp. 18, 30) ➥ Displays a variety of information, such as operating fre-
Appears when memory mode is selected. quency, set mode contents.
o MEMORY CHANNEL NUMBER • The decimal point blinks during scan.
➥ S hows the selected memory channel number. ➥ D uring memory mode operation, the programmed
(pp. 18, 30) memory or memory bank name is displayed.
➥ “C0” or “C1” appears when the call channel is selected. !6 TRANSMIT ICON (p. 23)
(pp. 18, 29) Appears during transmit.
!0 PRIORITY WATCH ICON (pp. 49, 50)
Appears when priority watch is in use.

BATTERY CHARGING 3
■ Caution (for the supplied BP-264 Ni-MH battery pack) 1
•R
DANGER! NEVER short terminals (or charging terminals) •C
lean the battery terminals to avoid rust or misscontact. 2
of the battery pack. Also, current may flow into nearby metal • Keep battery terminals clean. It’s a good idea to clean bat- 3
objects such as a necklace, so be careful when placing battery terminals once a week.
tery packs (or the transceiver) in handbags, etc.
• If your Ni-MH battery pack seems to have no capacity, even
4
Simply carrying with or placing near metal objects such as
a necklace, etc. may cause shorting. This may damage not
after being charged, completely discharge it by leaving the 5
power ON overnight. Then, fully charge the battery pack again.
only the battery pack, but also the transceiver.
If the battery pack still does not retain a charge (or only very lit-
6
•R
DANGER! NEVER incinerate used battery packs. Inter- tle charge), a new battery pack must be purchased. 7
nal battery gas may cause an explosion. Prior to using the transceiver for the first time, the battery
• R DANGER! NEVER immerse the battery pack in water. pack must be fully charged for optimum life and operation. 8
If the battery pack becomes wet, be sure to wipe it dry BE- • Recommended temperature range for charging: 9
FORE attaching it to the transceiver. between 0°C and +45°C for the regular charge by the
•C
AUTION: Always use the battery within the specified tem- transceiver.
10
perature range, –5˚C to +60˚C (+23˚F to +140˚F). Using or between +10°C and +40°C for the rapid charge with the 11
the battery out of its specified temperature range will re- BP-191.
duce the battery’s performance and battery life.
12
• Use the supplied charger (BC-167S) or optional charger
•C
AUTION: Shorter battery life could occur if the battery is (BC-191) only. NEVER use other manufacturers’ chargers. 13
left completely discharged, or in an excessive temperature • The battery pack contains a rechargeable battery. 14
environment (above +55˚C; +131˚F) for an extended period Charge the battery pack before first operating the trans-
of time. If the battery must be left unused for a long time, ceiver, or when the battery pack becomes exhausted. 15
it must be detached from the radio after charging. Keep it
safely in a cool dry place at the following temperature range:
If you want to prolong the battery life, the following points 16
should be observed:
–20˚C to +45˚C (–4˚F to +113˚F) (up to a month) - Avoid over charging. 17
–20˚C to +35˚C (–4˚F to +95˚F) (up to six months) - Use the battery pack until it becomes almost completely
–20˚C to +25˚C (–4˚F to +77˚F) (up to a year*)
18
exhausted, under normal conditions. We recommend bat-
* We recommend charging the battery pack every 6 months. tery charging after transmitting becomes impossible. 19

3 BATTERY CHARGING
■ Caution (for the optional BP-265 Li-Ion battery pack)

Misuse of Lithium-Ion batteries may result in the following •R
DANGER! DO NOT expose the battery to rain, snow,
hazards: smoke, fire, or the battery may rupture. Misuse seawater, or any other liquids. Do not charge or use a wet
can also cause damage to the battery or degradation of battery. If the battery gets wet, be sure to wipe it dry before
battery performance. using.
•R
DANGER! NEVER incinerate a used battery pack, since
•R
DANGER! Use and charge only specified Icom battery internal battery gas may cause it to rupture, or may cause
packs with Icom radios and Icom chargers. Only Icom bat- an explosion.
tery packs are tested and approved for use with Icom radios •R
DANGER! NEVER solder the battery terminals, or
or charged with Icom chargers. Using third-party or coun- NEVER modify the battery pack. This may cause heat gen-
terfeit battery packs may cause smoke, fire, or cause the eration, and the battery may burst, emit smoke or catch
battery to burst. fire.
•R
DANGER! Use the battery only with the transceiver for
D Battery caution which it is specified. Never use a battery with any other
•R
DANGER! DO NOT hammer or otherwise impact the bat- equipment, or for any purpose that is not specified in this
tery. Do not use the battery if it has been severely impacted instruction manual.
or dropped, or if the battery has been subjected to heavy •R
DANGER! If fluid from inside the battery gets in your
pressure. Battery damage may not be visible on the outside eyes, blindness can result. Rinse your eyes with clean water,
of the case. Even if the surface of the battery does not show without rubbing them, and see a doctor immediately.
cracks or any other damage, the cells inside the battery may
•R
WARNING! Immediately stop using the battery if it emits
rupture or catch fire.
an abnormal odor, heats up, or is discolored or deformed. If
•R
DANGER! NEVER use or leave battery pack in areas any of these conditions occur, contact your Icom dealer or
with temperatures above +60˚C (+140˚F). High tempera- distributor.
ture buildup in the battery, such as could occur near fires
•R
WARNING! Immediately wash, using clean water, any
or stoves, inside a sun heated car, or in direct sunlight may
part of the body that comes into contact with fluid from in-
cause the battery to rupture or catch fire. Excessive tem-
side the battery.
peratures may also degrade battery performance or shorten
battery life.

BATTERY CHARGING 3
1
• R WARNING! NEVER put the battery in a microwave oven, D Charging caution 2
high-pressure container, or in an induction heating cooker. • R DANGER! NEVER charge the battery pack in areas with 3
This could cause a fire, overheating, or cause the battery to extremely high temperatures, such as near fires or stoves,
rupture. inside a sun-heated vehicle, or in direct sunlight. In such
4
• CAUTION: Always use the battery within the specified tem- environments, the safety/protection circuit in the battery will 5
perature range, –20˚C to +60˚C (–4˚F to +140˚F). Using the activate, causing the battery to stop charging.
battery out of its specified temperature range will reduce the 6
• R WARNING! DO NOT charge or leave the battery in the
battery’s performance and battery life. battery charger beyond the specified time for charging. If 7
• CAUTION: Shorter battery life could occur if the battery is the battery is not completely charged by the specified time,
left fully charged, completely discharged, or in an excessive stop charging and remove the battery from the battery char-
8
temperature environment (above +50˚C; +122˚F) for an ex- ger. Continuing to charge the battery beyond the specified 9
tended period of time. If the battery must be left unused for a time limit may cause a fire, overheating, or the battery may
long time, it must be detached from the radio after discharg- rupture.
10
ing. You may use the battery until the remaining capacity is • R WARNING! NEVER insert the transceiver (battery at- 11
about half, and then keep it safely in a cool dry place at the tached to the transceiver) into the charger if it is wet or
following temperature range: 12
soiled. This could corrode the battery charger terminals or
–20˚C to +50˚C (–4˚F to +122˚F) (up to a month) damage the charger. The charger is not waterproof. 13
–20˚C to +35˚C (–4˚F to +95˚F) (up to three months)
–20˚C to +20˚C (–4˚F to +68˚F) (up to a year)
• CAUTION: DO NOT charge the battery outside of the speci- 14
fied temperature range: BC-193 (+10˚C to +40˚C; +50˚F to
+104˚F). Icom recommends charging the battery at +20˚C 15
(+68˚F). The battery may heat up or rupture if charged out 16
of the specified temperature range. Additionally, battery per-
formance or battery life may be reduced. 17
18
19
10
3 BATTERY CHARGING
■ Optional battery case (BP-263) ■ Battery information

When you would like to use the optional battery case (BP-263), D Battery life
install 6 × AA (LR6) size alkaline batteries, as shown below.
Battery pack Voltage Capacity Battery life*1
q Remove the battery case if it is attached. (p. 2) Battery case for
w Install 6 × AA (LR6) size alkaline batteries. BP-263 —*2
AA (LR6) × 6 alkaline
• Install only alkaline batteries.
• Be sure to observe the correct polarity. VHF 11.5 hrs.
BP-264 7.2 V 1400 mAh (typ.)
UHF 10 hrs.
Be careful! The negative
terminals of the battery case 1900 mAh (min.) VHF 16 hrs.
BP-265 7.4 V
protrude from the body, so 2000 mAh (typ.) UHF 13.5 hrs.
pay attention not to injure
*1 When the power save function is set to “Auto,” and the operating
your fingers when inserting time is calculated under the following conditions;
the batteries. TX : RX : standby = 5 : 5 : 90
*2 The average operating time depends on the alkaline cells used.
e Attach the battery case. (p. 2) ven when the transceiver power is OFF, a small current
E
CAUTION: still flows in the radio. Remove the battery pack or case
• W hen installing batteries, make sure they are all the from the transceiver when not using it for a long time. Oth-
same brand, type and capacity. Also, do not mix new erwise, the battery pack or installed batteries will become
and old batteries together. exhausted.
• Never use batteries whose insulated covering is damaged.
• Never incinerate used battery cells since internal battery Indication Battery condition
gas may cause them to rupture. The battery pack (BP-264/BP-265) or battery case
•N ever expose a detached battery case to water. If the bat- (BP-263) has ample capacity.
tery case gets wet, be sure to wipe it dry before using it. The battery pack (BP-264/BP-265) is nearing exhaus-
• Keep battery contacts clean. It’s a good idea to clean tion.
battery terminals once a week. The battery pack or battery case is exhausted. Charg-
ing the BP-264/BP-265 or replacing the batteries in the
(blinks) BP-263 is necessary.
11
BATTERY CHARGING 3
■ Regular charging Transceiver

• BC-167S
Prior to using the transceiver for the first time, the battery
pack must be fully charged for optimum life and operation. to AC outlet
3
The shape may
D Battery icons diffe depending
• CP-12L (Optional) on the version.
While charging, the icons show “ ,” “ ” and “ (dis-
appears)” in sequence, and “CHARGE” appears when the
transceiver’s power is OFF. The icons and “CHARGE” disap- to
[DC IN]
pear when the battery pack is completely charged.
to cigarette lighter
D Charging note socket (12 V DC)
• Be sure to turn the transceiver power OFF. • CP-19R (Optional)
Otherwise the battery pack will not be charged completely,
or will take much longer to charge.
• The transceiver can charge only the BP-264 battery pack. BP-264
Other types of rechargeable battery, such as Ni-Cd or Li-Ion
Turn power OFF while
cannot be charged. charging the battery • OPC-254L (Optional)
• External DC power operation becomes possible when using pack. to 11 V DC
an optional CP-12L, CP-19R or OPC-254L. The attached (power supply)
battery pack is also charged simultaneously, except during
• Charging time period:
transmit (see p. 15 for more details). Approx. 8 hours Black: _
• The external DC power supply voltage must be between
10–16 V to charge the battery pack and for operation when White: +
using an optional OPC-254L. We recommend 11 V DC for
operation.
• If the battery icons (“ ” and “ ”) disappear only 1 min. Be sure to disconnect the AC adapter from the AC outlet
after connecting to the DC power supply, the battery pack after the charging is completed. Otherwise the transceiver
may have problem. In this case, contact your Icom dealer/ may receive switching noise from the AC adapter, depend-
distributor, or purchase a new battery pack. ing on the operating frequencies and/or antenna used.
12
3 BATTERY CHARGING
■ Desktop battery chargers

D Charging note D Rapid charging with the BC-191
• Be sure to turn the transceiver power OFF. The BC-191 provides rapid charging of only the BP-264 Ni-MH
•N EVER place the transceiver with the battery pack to the battery pack. Never use it to charge any other battery pack.
desktop charger when the transceiver is connected to the Charging time (with the BC-123S): Approx. 2 hours
DC power supply. This may cause the charger’s malfunction
The following item is additionally required:
and the charging indicator of the charger lights red*. In that • The AC adapter BC-123S (not supplied with some versions) or the
case, disconnect the AC adapter from the charger, and then OPC-515L or CP-23L DC power cable.
reconnect the AC adapter to the charger.
*Red indicator is only available for the BC-191 or BC-193. Battery pack
Transceiver
• The optional CP-23L* and OPC-515L can be used instead BC-123S
of the supplied AC adapter. Connect one of these to the
[DC 12-16V] jack.
* CP-23L can only be used with the BC-191 or BC-193.
IMPORTANT: Tabs
Ensure the tabs on the battery
pack are correctly aligned with Turn power OFF
the guide rails inside the charger.
Screws*
(Self tapping screw:
M3.5 × at least 30 mm)
*Purchase separately.
Guide rail Using screws is
The optional OPC- recommended to
515L (for a DC power secure the charger.
CAUTION: When using the OPC-515L DC power cable source) or CP-23L
NEVER connect the OPC-515L to a power source using (for a 12 V cigarette Charge indicator
reverse polarity. This will ruin the battery charger. lighter socket) can be • Lights orange : While charging
used instead of the • Lights green : Charging is completed
White line: + Black line: – AC adapter. • Blinks red : Charging error has occured
13
BATTERY CHARGING 3
D Regular chrging with the BC-192 D Rapid charging with the BC-193
The BC-192 provides regular charging of only the BP-264 Ni-MH The BC-193 provides rapid charging of only the BP-265 Li-
battery pack. Never use it to charge any other battery pack. Ion battery pack. Never use it to charge any other battery
Charging time (with the BC-147S): Approx. 16 hours pack. 3
Charging time: Approx. 2.5 hours
The following item is additionally required:
• The AC adapter BC-147S (not supplied with some versions) or the The following item is additionally required:
OPC-515L DC power cable. • The AC adapter BC-167S (not supplied with some versions) or the
OPC-515L or CP-23L DC power cable.
BC-147S
Battery pack
Transceiver Battery pack
Transceiver
BC-123S
Turn power OFF

Turn power OFF
Screws*
(Self tapping screw:
M3.5 × at least 30 mm) Screws*
*Purchase separately. (Self tapping screw:
Using screws is M3.5 × at least 30 mm)
The optional recommended to *Purchase separately.
OPC-515L (for secure the charger. Using screws is
a DC power recommended to
source) can be The optional OPC- secure the charger.
Charge indicator
used instead of 515L (for a DC power
the AC adapter.
Charging time period differs • Lights green while charging. Charge indicator
depending on the input voltage. NOTE: source) can be used
instead of the AC • Lights orange : While charging
12 V : Approx. 36 hours The charger indicator will • Lights green : Charging is completed
adapter.
13.8 V : Approx. 21 hours not go out even after a • Blinks red : Charging error has occured
16 V : Approx. 16 hours battery pack is fully charged.
14
3 BATTERY CHARGING
■ External DC power operation

An optional cigarette lighter cable (CP-12L or CP-19R; for • CP-12L (Optional)
Transceiver
12 V cigarette lighter socket) or external DC power cable
(OPC-254L) can be used for external power operation. (We
recommend the CP-19R when you want to connect a 12 V
cigarette lighter socket.)
to cigarette lighter
socket (12 V DC)
D Operating note to • CP-19R (Optional)
• Power supply voltage must be between 10.0–16.0 V DC. [DC IN]
(We recommend 11.0 V DC.) NEVER CONNECT OVER
16 V DC directly into the [DC IN] jack of the transceiver.
•B E SURE to use a CP-12L, CP-19R or OPC-254L when
connecting to a regulated 12 V DC power supply.
Use an external DC-DC converter to connect the trans- • OPC-254L (Optional)
ceiver through a CP-12L, CP-19R or OPC-254L to a 24 V
DC power source. to 11 V DC
BP-264 (power supply)
• The voltage of the external power supply must be within
10–16 V DC when using either CP-12L, CP-19R or OPC-
Black: _
254L, otherwise, use the battery pack/battery case.
• D isconnect the power cable from the transceiver when
White: +
not using it. Otherwise, the vehicle battery will become ex-
hausted.
• The power save function is automatically deactivated dur- NOTE: Up to 5 W (approx.) of maximum output power
ing external DC power operation. is available when using an external DC power. However,
when the supplied voltage exceeds 14 V, the built-in pro-
tection circuit activates to reduce the transmit output power
to 2.5 W (approx.).
15
BASIC OPERATION 4
■ Power ON ■ Setting audio volume 1
➥ Push and hold [ ] for 1 sec. to turn power ON. ➥ Rotate [VOL] to adjust the audio level. 2
• Push and hold [ ] for 1 sec. to turn power OFF. • If squelch is closed, push and hold [MONI](BAND) while setting 3
the audio level.
• The display shows the volume level while setting. 4
5
[VOL]
6
7
8
9
10
Volume level
11
12
The voltage indication can be skipped in the Initial set mode
13
(p. 61). Minimum setting (no audio)
14
15
16
Maximum setting
17
The beep level is adjusted in the Initial set mode (p. 60).
18
19
16
4 BASIC OPERATION
■ Setting the squelch level ■ Monitor function

The squelch circuit mutes the received audio signal, depend- This function is used to listen to weak signals without disturb-
ing on the signal strength. The transceiver has 9 squelch lev- ing the squelch setting; or to open the squelch manually even
els, a continuously open setting and an automatic setting. when mute functions such as the tone squelch are in use.
➥ While continuing to push [MONI](BAND), rotate [DIAL] to ➥ Push and hold [MONI](BAND) to monitor the operating
select the squelch level. frequency.
• “LEVEL1” is loose squelch (for weak signals) and “LEVEL9” is • The 1st and 2nd segments of the S-meter blink.
tight squelch (for strong signals).
• “Auto” indicates the automatic level adjustment by a noise pulse
counting system.
• “OPEn” indicates the continuously open setting.
[DIAL]
Two segments blink
he [MONI] key can be set to a ‘sticky’ operation in the

T
Automatic squelch Initial set mode. See page 63 for details.
Maximum level
17
BASIC OPERATION 4
■ Selecting the mode 1

q Push [V/M/C] repeatedly to sequen- D Memory mode 2
[DIAL]
tially select the VFO mode, memory Memory mode is used for opera- • Memory mode display 3
mode, call channel mode or weather tion on memory channels which
channel mode*. store programmed frequencies. 4
*Only for the U.S.A. version transceiver. • “ ” appears when memory mode 5
w R otate [DIAL] to change the fre- is selected.
quency or select a desired channel. • Only programmed memory chan- Appears 6
nels can be selected.
7
• Enter the channel number directly to select the desired memory
D VFO mode channel. (p. 30) 8
The VFO mode is used to set the desired frequency.
9
• VFO mode display D Call channel mode 10
Select a call channel to operate • Call channel display
on one of your two most often- 11
used frequencies. 12
• “ C0” or “C1” appears instead of the
memory channel number when the 13
What is VFO? Call channel mode is selected.
VFO is an abbreviation of Variable Frequency Oscillator. Fre-
14
quencies for both transmitting and receiving are generated D Weather channel mode* 15
and controlled by the VFO.
There are 10 weather channels • Weather channel display 16
for monitoring weather broad-
casts from NOAA (National 17
Oceanic and Atmospheric Ad- 18
ministration).
*Only for the U.S.A. version transceiver. 19
18
4 BASIC OPERATION
■ Setting the tuning step ■ Setting the frequency

The tuning step can be selected for both band. The following D Using the dial
tuning steps are available for the IC-T70A/T70E. q Push [V/M/C] to select the VFO mode, if any other mode is
• 5.0 kHz • 10.0 kHz • 12.5 kHz • 15.0 kHz selected.
• 20.0 kHz • 25.0 kHz • 30.0 kHz • 50.0 kHz w Push [BAND] to select the desired frequency band.
• 100.0 kHz • 125.0 kHz • 200.0 kHz e Rotate [DIAL] to select the desired frequency.
• The frequency changes according to the preset tuning steps.
D Tuning step selection See the previous topic to set the tuning step.
q In the VFO mode, push [BAND] to select the desired fre- • 144 MHz band
quency band. [DIAL]
• If you are in another mode, such as a memory channel/call
channel mode or the weather channel mode, push [V/M/C] to
select the VFO mode first, then push [BAND] to select the de-
sired band. Push [BAND]
w Push [SET] to enter the Set mode. • 440 MHz band
e Rotate [DIAL] to select the tuning step set item, then ro-
tate [VOL] to select the desired tuning step.
r Push [V/M/C] to return to the VFO mode.
[DIAL]
[VOL]
[DIAL] changes the frequency

according to the selected
tuning step.
5 kHz tuning step
19
BASIC OPERATION 4
D Using the keypad 1

The frequency can be directly set using the nu-
meric keys. Depending on the
2
• If a frequency outside the transceiver’s frequency tuning step setting, it 3
range is entered, the previously displayed fre- may not be possible to
quency is automatically recalled after entering the input a 1 kHz digit. In 4
last digit. this case, enter “0” as 5
a 1 kHz digit, then ro-
q Push [V/M/C] to select the VFO mode, if any
tate [DIAL] to set the 6
other mode is selected.
w Enter the desired frequency with the keypad.
desired frequency. 7
8
• Entering 145.500 MHz
9
10
11
• Changing 10 MHz and below Editing 445.560 MHz to 432.380 MHz
12
13
• Changing 1 MHz and below Editing 145.500 MHz to 144.640 MHz
14
15
16
• Changing 100 kHz and below Editing 145.500 MHz to 145.640 MHz 17
18
Push to cancel numeral key input. 19
20
4 BASIC OPERATION
■ Operating mode selection ■ Key lock function

Operating modes are determined by the modulation of the To prevent accidental frequency changes and unnecessary
radio signals. The transceiver has two operating modes, FM function access, use the lock function.
and FM-N (narrow). The mode selection is stored indepen-
dently for each band and memory channel. ➥ Push and hold [ ](SET) for 1 sec. to turn the lock func-
tion ON or OFF.
q Push [V/M/C] to select the VFO mode, if any other mode is •“ ” appears while the lock function is activated.
selected. • [ ], [ ](SET), [MONI](BAND), [PTT], [VOL] and squelch ad-
w Push [BAND] to select the desired frequency band. justment ([MONI](BAND) + [DIAL]) are operable while the lock
function is activated.
e Push [SET] to enter the Set mode.
r Rotate [DIAL] to select the operating mode set item, then
rotate [VOL] to select “WIdE” (FM) or “nARROW” (FM-nar-
row). Appears
t Push [V/M/C] to return to the VFO mode.
[DIAL]
[VOL]
To prevent accidental transmission, the transceiver has a

PTT lock function. Turns the PTT lock function ON or OFF
FM FMN in the Initial set mode. (p. 62)
: Rotate [VOL]
21
BASIC OPERATION 4
■ Receiving ■ Transmit power selection 1

Make sure a charged battery pack (BP-264, BP-265) or a The transceiver has three output power levels to suit your op- 2
case with brand new alkaline batteries (BP-263) is attached erating requirements. Low output power during short-range 3
to the transceiver (pp. 2, 12–14). communications may reduce the possibility of interference to
other stations, and will conserve battery power. 4
q Push and hold [ ] for 1 sec. to turn power ON.
w Rotate [VOL] to set the desired audio level. (p. 16) ➥ Push [H/M/L] to toggle the transmit output power between
5
• The frequency display shows the volume level while setting. High (5 W*), Middle (2.5 W*) and Low (0.5 W*). 6
e Set the receive frequency. (p. 20) *Approximately
r Set the squelch level. (p. 17) 7
• While continuing to push [MONI](BAND), rotate [DIAL].
8
• The first click of [DIAL] indicates the current squelch level.
• “LEVEL1” is loose squelch (for weak signals) and “LEVEL9” is 9
tight squelch (for strong signals).
• “Auto” indicates the automatic level adjustment by a noise pulse
Appears 10
counting system. • While transmitting 11
• Push and hold [MONI](BAND) to open the squelch manually.
t When a signal is received:
12
• Squelch opens and audio is heard. 13
• The S/RF meter shows the relative signal strength level.
r Set squelch level
Low power transmission
14
e Set frequency 15
w Set audio level
Middle power transmission 16
r Push and hold for 17
setting the squelch
(Push and hold
q Power ON High power transmission 18
to monitor) 19
e Select band
22
4 BASIC OPERATION
■ Transmitting
CAUTION: T
ransmitting without an antenna will damage the R WARNING! NEVER transmit for long periods of time.
transceiver. When the transceiver is used for prolonged transmissions
at high power or middle power, the transceiver radiates heat
NOTE: To prevent interference, push and hold [MONI] to protect itself from overheating. The transceiver’s chassis
(BAND) to listen on the frequency before transmitting. will become hot and may cause a burn.
• To prevent the transceiver’s overheating, the default setting of
q Set the operating frequency. (p. 20) the time-out timer function is set to 5 minutes (p. 62). Be careful
• You can transmit on the 144 MHz/440 when the time-out timer function is turned OFF or set to a long
time period, and transmission is made for long periods.
MHz amateur bands only.
• Select the desired output power. See DO NOT operate the transceiver in a situation that will ob-
the previous page for details. struct heat dissipation, especially if the transceiver is oper-
w Push and hold [PTT] to transmit. ated with an external power supply. Heat dissipation may
[PTT]
•“ ” appears. be affected, and it may cause a burn, warp the casing or
• T he S/RF meter shows the output damage the transceiver.
power level. NOTE: When the transceiver becomes hot from continuous
e Speak into the microphone using transmission, etc., the transceiver’s heat protection function
your normal voice level. Microphone
gradually reduces the output power to 2.5 W (Mid), then
• DO NOT hold the transceiver too close it stops transmission after that. This is done to protect the
Appears
to your mouth or speak too loudly. This transceiver itself until it has cooled down.
may distort your speech. • “M” (Power icon) blinks while the heat protection function reduces
r Release [PTT] to return to receive. the output power.
• “Hot” is displayed while the heat protection function inhibits trans-
mission.
While using the battery case:
Frequent or continuous transmissions can cause the batteries
to overheat. To prevent this, we recommend using the middle or
low power settings.
23
REPEATER AND DUPLEX OPERATIONS 5
■ Repeater operation Appears
1
When using a repeater, the transmit frequency is shifted from e Push and hold [TONE](0) for 1 sec. 2
the receive frequency by the frequency offset (p. 54). This is to activate the subaudible tone en- 3
called duplex operation. It is convenient to program repeater coder, according to the repeater re-
quirements. 4
information into memory channels (p. 29).
• “T” appears.
Refer to p. 53 for tone frequency set-
5
Repeater
144.700 MHz 144.700 MHz Uplink tings.
[PTT]
6
(transmit frequency)
r Push and hold [PTT] to transmit.
Downlink • T he displayed frequency automati- 7
145.300 MHz 145.300 MHz (receive frequency)
cally changes to the transmit fre-
quency (repeater input frequency).
8
Station A Station B • If “OFF” appears, check the frequency 9
offset or shift direction. (p. 26)
10
While receiving While transmitting
q Set the receive frequency (repeater output frequency).
11
w Set the shift direction of the transmit frequency. (DUP– or 12
DUP; see p. 26 for details.)
• When the auto repeater function is in use (U.S.A. and Korean 13
versions only), this selection and step e are not necessary.
(p. 27)
14
t Release [PTT] to receive.
“DUP–”or “DUP” appears 15
y Push and hold [MONI](BAND) to check whether the other
station’s transmit signal can be directly received or not. 16
U.S.A. and Korean versions: 17
he auto repeater function uses standard values of the
T 18
repeater tone frequency and frequency offset.
19
24
5 REPEATER AND DUPLEX OPERATIONS
D Checking the repeater input signal D Off band indication

The transceiver can check whether the other station’s trans- If the transmit frequency is out of the amateur band when
mit signal can be received directly or not, by listening on the [PTT] is pushed, the off band indication, “OFF,” appears on
repeater input frequency. the display. Check the frequency offset or duplex direction in
that case. (p. 26)
➥ Push and hold [MONI](BAND) to check whether the other
station’s transmit signal can be received directly or not.
• When the other station’s signal can be directly received, move
to a non-repeater frequency to use simplex. (duplex OFF)
Display while receiving
U.S.A. and Korean versions:
he auto repeater function uses standard values of the
T
frequency offset.
Push and hold

✔ CONVENIENT!
Receives –0.6 MHz lower Tone scan function: When you don’t know the subaudible
tone used for a repeater, the tone scan is convenient for de-
tecting the tone frequency.
➥ Push and hold [T.SCAN](#) for 1 sec. to start the tone
scan. See p. 71 for more information.
Blinks while pushing and holding [MONI]
25
■ Duplex operation 1
D Setting frequency offset
U.S.A. and Korean versions: 2
The auto repeater function has priority over the manual duplex
q Push [SET] to enter the Set mode. [DIAL] setting. If the transmit frequency changes after setting, the 3
w Rotate [DIAL] to select the frequency [VOL] auto repeater function may have changed the duplex setting. 4
offset set item, then rotate [VOL] to set Turn the auto repeater function OFF to prevent this (p. 27).
the frequency offset. 5
e Push [V/M/C] to return to the frequency
6
display. ■ Reverse duplex function
7
When the reverse duplex function is ON, the receive and
transmit frequencies are reversed. The function can be set in 8
Frequency offset setting 0.6 MHz offset the Set mode.
9
q Push [SET] to enter the Set mode.
D Setting duplex direction w Rotate [DIAL] to select the reverse duplex set item, then
10
➥ Push and hold [DUP](M) for 1 sec. to select “DUP–” (nega- rotate [VOL] to turn the function ON or OFF. 11
tive offset) or “DUP” (positive offset).
• “DUP–” or “DUP” indicates the transmit frequency for minus 12
shift or plus shift, respectively.
• While continuing to push [DUP](M), rotate [DIAL] also selects Reverse duplex setting 13
a duplex setting. e Push [V/M/C] to return to the frequency display. 14
• When the frequency offset is 0.6 MHz
[DIAL] –Duplex example
Each receive and transmit frequency is shown in the table 15
below, with the following configurations; 16
Input freq.: 145.300 MHz, Direction: – (down), Offset: 0.6 MHz 17
Receiving Transmitting • “ DUP–” or “DUP” blinks
Reversed RX freq. TX freq.
when the reverse duplex 18
OFF 145.300 MHz 144.700 MHz
ON 144.700 MHz 145.300 MHz
function is ON. 19
+Duplex example
26
5 REPEATER AND DUPLEX OPERATIONS
■ Auto repeater function

The U.S.A. and Korean versions automatically use standard q While continuing to push [SET], turn the power ON to
repeater settings (duplex ON/OFF, duplex direction, tone encoder enter the Initial set mode.
ON/OFF) when the operating frequency falls within or outside w Rotate [DIAL] to select the auto repeater set item, then
of the general repeater output frequency range. The offset rotate [VOL] to set the auto repeater setting.
and repeater tone frequencies are not changed by the auto U.S.A. version:
repeater function. Reset these frequencies, if necessary. • “R1” : Activates duplex only. (default)
• “R2” : Activates duplex and tone.
• “OFF” : Auto repeater function is turned OFF.
D Frequency range and offset direction Korean version:
• U.S.A. version • “On” : Activates duplex and tone. (default)
• “OFF” : Auto repeater function is turned OFF.
FREQUENCY RANGE SHIFT DIRECTION
Auto repeater setting
145.200–145.495 MHz [DIAL]
“DUP–” appears [VOL]
146.610–146.995 MHz
147.000–147.395 MHz “DUP” appears
442.000–444.995 MHz “DUP” appears
U.S.A. version
447.000–449.995 MHz “DUP–” appears
• Korean version
FREQUENCY RANGE SHIFT DIRECTION Korean version

439.000–440.000 MHz “DUP–” appears
e Push [ ] to return to the frequency display.

27
■ 1750 Hz tone 1
To access some European repeaters, the transceiver must r Set the receive frequency (repeater output frequency). 2
transmit a 1750 Hz tone burst. For such repeaters, perform t Set the shift direction of the transmit frequency. (–DUP or 3
the following. +DUP; see p. 26 for details.)
• This tone can be use as a ‘Call signal’ in countries out of Europe. y While continuing to push [PTT], push [MONI](BAND) to 4
transmit a 1750 Hz tone burst signal. 5
q Push [SET] to enter the Set mode. • If “OFF” appears, check the frequency offset or shift direction.
w Rotate [DIAL] to select the DTMF key item, then rotate (p. 26) 6
[VOL] to set to “t-CALL.” • The displayed frequency automatically changes to the transmit
7
DTMF key setting frequency (repeater input frequency).
[DIAL] u Push and hold [PTT] to transmit. 8
[VOL] i Release [PTT] to receive.
o Push and hold [MONI](BAND) to check whether the other
9
station’s transmit signal can be received directly or not, by 10
listening on the repeater input frequency.
11
✔ CONVENIENT! (For the IC-T70E only) 12
q Set the receive frequency (repeater output frequency). 13
w Set the shift direction of the transmit frequency. (–DUP or
+DUP; see p. 26 for details.) 14
e Push [PTT] briefly, then push and hold [PTT] again for 1 to
2 sec. to transmit a 1750 Hz tone burst signal.
15
• If “OFF” appears, check the frequency offset or shift direction. 16
Tone call setting (p. 26)
• The displayed frequency automatically changes to the transmit
17
e Push [V/M/C] to return to the frequency display.
frequency (repeater input frequency). 18
r Push and hold [PTT] to transmit; release to receive.
19
28
6 MEMORY/CALL CHANNELS
■ General description ■ Selecting a call channel

The IC-T70A/T70E has 300 memory channels, and 2 call q Push [V/M/C] to select the call channel mode.
channels. Memory channels include 50 scan edge memory • Pushing [V/M/C] toggles between the VFO mode, the memory
channels (25 pairs) to store often-used frequencies. channel mode, call channel mode and weather channel mode*.
Also, 26 memory banks, A to Z, are available in each band for *Only the U.S.A. version transceiver.
storing groups of frequencies, etc. Up to 100 channels can be w Rotate [DIAL] to select a desired call channel.
assigned to a bank. • “C0” and “C1” are selectable.
VHF band call channel
D Memory channel contents [DIAL]
The following information can be programmed into memory
channels:
• Operating frequency (p. 20)
• Operating mode (p. 21) UHF band call channel
• Duplex direction (+DUP or –DUP) with a frequency offset
(p. 26)
• Reverse duplex function ON/OFF (p. 26)
• Subaudible tone encoder (p. 24), tone squelch or DTCS
squelch ON/OFF (p. 70)
• Subaudible tone frequency (p. 53), tone squelch fre-
quency or DTCS code with polarity (p. 53)
• Scan skip setting (p. 46)
• Memory bank (p. 32)
• Memory name (p. 34)
• Tuning step (p. 19)
• Output power (p. 22)
NOTE: Memory data can be erased by static electricity, electric transients, etc.
In addition, it can be erased by malfunction and during repairs. Therefore, we recommend that memory data be written down or
be saved to a PC using the CS-T70 cloning software.
29
MEMORY/CALL CHANNELS 6
■ Selecting a memory channel 1

D Using [DIAL] D Using the Numeral keys 2
q Push [V/M/C] to select the memory mode. q Push [V/M/C] to select the memory mode. 3
• Pushing [V/M/C] toggles between the VFO mode, the memory • Pushing [V/M/C] toggles between the VFO mode, the memory
channel mode, call channel mode and weather channel mode*. 4
channel mode, call channel mode and weather channel mode*.
*Only the U.S.A. version transceiver. *Only the U.S.A. version transceiver. 5
w Rotate [DIAL] to select a desired memory channel. w Use the number keys to enter 3 digits to select a desired
• Only programmed channels are displayed. memory channel. 6
• The blank channels are also selectable.
[DIAL] Appears
7
• Example— selecting memory channel “25” 8
Push [V/M/C], then push [0], [2], [5].
9
Appears
10
Rotate [DIAL] to select
11
the memory channel. 12
13
The entered memory
channel is selected. 14
Numeral
keys 15
16
17
18
19
30
■ Memory channel programming

q Push [V/M/C] to select the VFO mode. r Rotate [DIAL] to select a desired channel.
w Set a desired frequency: • Call channels (C0, C1), VFO and scan edge channels (0A/0b
➥ Push [BAND] to select a desired band. to 24A/24b), as well as regular memory channels, can be pro-
➥ Rotate [DIAL] to set a desired frequency. grammed in this way.
➥ Push the keypad keys directly to set a desired fre- t Push and hold [S.MW](V/M/C) for 1 sec. to program.
quency. In this case, setting the band and frequency • 3 beeps sound.
using [BAND] and [DIAL] are not required. • Memory channel number automatically increases when continu-
➥ Set other data (e.g. frequency offset, duplex direction, ing to push [S.MW](V/M/C) for 1 sec. after programming.
tone squelch, etc.), if desired.
NOTE: Push [H/M/L] to cancel the program and exit the
e Push and hold [S.MW](V/M/C) for 1 sec. to enter the select
select memory write mode before memory programming is
memory write mode.
• 1 short and 1 long beep sounds.
finished.
• The “ ” icon and memory channel number blink.
[EXAMPLE]: Programming 145.440 MHz into memory channel 11 (a blank channel).

[DIAL] Push and hold for 1 sec. Rotate to select channel 11.
The VFO mode Enter the select memory write mode.

Channel 11
Push and hold for 1 sec. to program.
Return to the VFO mode.
31
■ Memory bank setting 1

The IC-T70A/T70E has a total of 26 banks (A to Z). Regular r Rotate [DIAL] to select a desired bank group from “A” to “Z.” 2
[DIAL]
memory channels 0 to 249 and scan edge memory channels 3
0A to 24b are assigned to any desired bank for easy memory
management. 4
q Push and hold [S.MW](V/M/C) for 1 sec. to enter the select
5
memory write mode. 6
7
w Rotate [DIAL] to select a desired memory channel. 8
e Push [SET] to select the “bAnk” item.
• The bank group and channel number are displayed if the selected
t Push [BAND] to select the bank channel digit, then rotate 9
[DIAL] to select the bank channel number from “00” to “99.”
memory channel has already been assigned to a bank.
• Push [BAND] to toggle the bank group selection and bank chan- 10
[DIAL]
nel selection. 11
[DIAL]
12
13
Push
Rotate 14
15
16
17
y Push and hold [S.MW](V/M/C) for 1 sec. to assign the
channel to the bank.
18
• Return to the previous indication before entering the select 19
memory write mode.
32
■ Memory bank selection

q Push [V/M/C] to select the memory mode. r Rotate [DIAL] to select the bank channel.
w Push [BAND] to enter the bank selection mode. • Only programmed channels are displayed.
e Rotate [DIAL] to select a desired bank (A to Z), then push [DIAL]
[BAND].
• Only programmed banks are displayed.
• Also regular memory channel can be selected.
[DIAL]
Bank channel is selected.

Push
Regular memory channel

is displayed.
Rotate
Bank channel is displayed.

Push
33
■ Programming memory/bank/scan name 1

Each memory channel can be programmed with an alphanu- u Repeat step y until a desired channel name is pro- 2
meric channel name for easy recognition as well as displayed grammed. 3
independently by channel. Names can be a maximum of 6 i Push and hold [S.MW](V/M/C) for 1 sec. to set the name
characters. and exit the channel name programming state. 4
• 3 beeps sound.
OTE: Scan name display can be turned ON or OFF in
N 5
the Initial set mode. (p. 63) OTE: Only one bank name can be programmed into each
N 6
q Push [V/M/C] to select the memory mode. bank. Therefore, the previously programmed bank name
w Push and hold [S.MW](V/M/C) for 1 sec. to enter the select will be displayed when bank name is selected. Also, the 7
memory write mode. programmed bank name is assigned automatically to an- 8
• 1 short and 1 long beep sounds. other bank channel.
• The “ ” icon and memory channel number blink. 9
e Rotate [DIAL] to select a desired memory channel. D Usable characters 10
• Select Call channels (C0 or C1) to program a call channel, or
scan edge channels (0A/0b to 24A/24b) to program a scan 11
name. (A) (b) (C) (d) (E) (F) (G) (H) (I) (J) (k) (L) (m) 12
r Push [SET] repeatedly to select “b nAmE,” “m nAmE” or
“S nAmE” when programming the bank name, the memory 13
(n) (O) (P) (q) (R) (S) (t) (U) (V) (W) (X) (y) (Z)
name or the scan name, respectively.
14
t Push and hold [SET] for 1 sec. to enter the name program-
ming mode. (0) (1) (2) (3) (4) (5) (6) (7) (8) (9) 15
• After selecting the name to be programmed, a cursor blinks for
the first character.
16
y Rotate [DIAL] to select a desired character. (+) (-) (=) (∗) (/) (() ()) (:) (Space)
17
• The selected character blinks.
• Push [BAND] to move the cursor right; push [SET] to move the
18
cursor left. 19
34
■ Programming memory/bank/scan name (continued)

■ Selecting memory/bank
[EXAMPLE]: Programming the bank name “VHF” into the
scan edge channel 1A
name indication
During memory mode, rotate Push and hold During memory mode operation, either the programmed
to select scan edge channel 1A. for 1 sec. memory name or bank name can be displayed.
q While continuing to push [SET], turn the power ON to

enter the Initial set mode.
w Rotate [DIAL] to select the memory name item, then rotate
Push and hold Rotate to select “V,” [VOL] to set the memory name display option.
for 1 sec. then push . • “OFF” : Memory name display is turned OFF.
• “On” : Turns ON the memory name display. (default)
[DIAL] Memory name setting
[VOL]
Enter the select memory
write mode.
Select “H” and “F”
Push repeatedly
with and .
to select “b nAmE*2.”
Push and hold e Push [ ] to return to the frequency display.

for 1 sec. to program.
Select “m nAmE” or “S nAmE*1”

when programming the memory
name or the scan name, respectively.
*1 S nAmE can be set for scan edge channels only.
*2 b nAmE can be set for bank assigned channels only.
35
■ Display type 1
During memory mode operation, the transceiver has 3 “Channel number display” 2
display types to suit your operating style. Set the display type Displays the memor y channel 3
in the Initial set mode. number. Only programmed mem-
ory channels are displayed, and 4
q While continuing to push [SET], turn the power ON to modes other than the memory
enter the Initial set mode. mode cannot be selected.
5
w Rotate [DIAL] to select the display mode item, then rotate • W hen the channel number display type is selected, only the 6
[VOL] to set the display type from “FREq,” “CH” or “PRIV.”
[DIAL] Display mode setting
following functions can be performed. 7
- Scan function (p. 44) - Output power setting (p. 22)
[VOL] - Monitor function (p. 17) - Key lock function (p. 21) 8
- DTMF transmit function (p. 66)
9
- The scan pause timer setting, the scan resume timer setting, the
DTMF memory selection, the mic gain setting and the VOX gain 10
setting in the Set mode.
11
“Private channel display” 12
Displays the memory channel
number. Only programmed mem- 13
ory channels 0 to 5 are displayed, 14
and modes other than the mem-
“Frequency display”
ory mode cannot be selected. 15
Displays the programmed fre-
quency. (default) • W hen the private channel display type is selected, only the 16
following functions can be performed.
- Output power setting (p. 22) - Monitor function (p. 17)
17
- Key lock function (p. 21) - DTMF transmit function (p. 66) 18
19
36
■ Copying memory/call contents

This function transfers a memory channel’s contents to VFO ushing and holding [S.MW](V/M/C) for 2 seconds in step
P
(or another memory/call channel). This is useful when search- w will also copy the memory contents to the VFO. In that
ing for signals around a memory channel frequency and for case, steps e and r are not necessary.
recalling the frequency offset, subaudible tone frequency etc.
D Memory/call➪memory/call
D Memory/call➪VFO q Select the memory (call) channel to be copied.
q Select the memory (call) channel to be copied. ➥ Push [V/M/C] repeatedly to select the memory mode
➥ Push [V/M/C] repeatedly to select the memory mode or the call channel mode, then rotate [DIAL] to select a
or the call channel mode, then rotate [DIAL] to select a desired channel.
desired channel. w Push and hold [S.MW](V/M/C) for 1 sec. to enter the select
w Push and hold [S.MW](V/M/C) for 1 sec. to enter the select memory write mode.
memory write mode. • 1 short and 1 long beep sounds.
• 1 short and 1 long beep sounds. • The “ ” icon and memory channel number blink.
• The “ ” icon and memory channel number blink. • Do not hold [S.MW](V/M/C) for more than 2 seconds. Otherwise
e Rotate [DIAL] to select “VFO.” the memory contents will be copied to the VFO mode.
r Push and hold [S.MW](V/M/C) for 1 sec. to write the se- e Rotate [DIAL] to select the target memory (call) channel.
lected channel contents to the VFO mode. r Push and hold [S.MW](V/M/C) for 1 sec. again to copy.
• Returns to the VFO mode automatically.
[DIAL] [EXAMPLE]: Copying memory channel 11 to the VFO mode.
Push and hold for 1 sec. Rotate to select “VFO.” Push and hold for 1 sec.
Memory mode Enter Return to the VFO mode.

the select memory write mode. “VFO” is selected.
37
■ Memory clearing 1
Contents of programmed memories can be cleared (erased), e Push [SET] repeatedly to select “CLEAR.”
2
if desired. r Push and hold [S.MW](V/M/C) for 1 sec. to clear the con- 3
tents.
q Push and hold [S.MW](V/M/C) for 1 sec. to enter the select
• 3 beeps sound. 4
memory write mode.
• The cleared channel changes into a blank channel 5
• Return to the select memory write mode. Memory channel num-
ber blinks. 6
• Do not hold [S.MW](V/M/C) for more than 2 seconds. Otherwise
t Push [H/M/L] to exit the select memory write mode. 7
the memory contents will be copied to the VFO mode.
w Rotate [DIAL] to select a desired memory channel to be NOTE: Be careful!— the contents of cleared memories 8
cleared. CANNOT be recalled.
9
[EXAMPLE]: Clearing memory channel 14. 10
[DIAL] Push and hold for 1 sec. Rotate to select a desired channel. 11
12
13
The VFO mode Enter the select memory write mode. Channel 14 14
Push repeatedly to select “CLEAR.” 15
16
Push and hold for 1 sec to clear.
Push to return 17
to the VFO mode. 18
19
38
■ Erasing/transferring bank contents

The bank contents of programmed memory channels can be • Do not hold [S.MW](V/M/C) for more than 2 seconds. Otherwise
cleared or reassigned to another memory bank. the memory contents will be copied to the VFO.
INFORMATION: Even if the memory bank contents are e Push [SET] repeatedly to select “bAnk.”
cleared, the memory channel contents still remain
programmed.
q Select a desired bank’s contents to be transferred or

erased from the bank. (p. 33) r Push [BAND] to toggle the bank channels selection or the
➥ Push [BAND] to enter the memory bank selection bank group selection.
mode. t Rotate [DIAL] to select a desired bank group or channel to
➥ Rotate [DIAL] to select a desired memory bank group, be transferred.
then push [BAND]. Or, select the “-- -- -- --” display when erasing the contents
➥ Rotate [DIAL] to select the bank channel. from the bank.
[DIAL] To transfer the bank contents
to ch 11 in Bank b.
[DIAL]
Bank channel is displayed.

To erase
w Push [S.MW](V/M/C) for 1 sec. to enter the select memory

write mode.
• 1 short and 1 long beep sounds. is displayed.
• Automatically displays the original memory channel number, and
y Push [S.MW](V/M/C) for 1 sec. to erase/transfer the bank
then the “ ” icon and memory channel number blink.
contents.
39
SCAN OPERATION 7
■ Scan types 1
Scanning automatically searches for signals and makes 2
it easier to locate new stations for contact or listening pur- 3
poses.
4
5
FULL SCAN (p. 42) SELECTED BAND SCAN (p. 42)
144 MHz 440 MHz
Repeatedly scans all frequen- Band Band Repeatedly scans all frequen-
6
band band
7
edge edge
cies over the entire band. cies over the entire selected
Scan Scan Scan
Some frequency ranges are not band.
Jump
scanned, depending on the fre- Jump 8
quency coverage of the trans- 9
ceiver’s version.
10
11
PROGRAMMED SCAN (p. 42) FREQUENCY/MEMORY SKIP FUNCTION
Band
edge xxA
Scan edges Band
xxB edge
Repeatedly scans between two Band Band Skips unwanted frequencies or 12
edge edge
Scan
user-programmed frequencies.
Scan
channels that inconveniently 13
Used to check for frequencies stop scanning.
Jump
within a specified range, such
SKIP Jump SKIP
This setting can be turned ON or 14
as repeater output frequencies, OFF in the select memory write 15
etc. mode. (p. 46)
16
PROGRAMMED LINK SCAN (pp. 42, 57) The frequency skip scan function can be turned ON or OFF 17
Repeatedly scans user-programmed frequencies selected in the Set mode. When this function is set to ON, the speci- 18
in the “P-LInk” item in the Set mode. fied frequencies are skipped during VFO scan. (p. 55)
• The “P ” icon appears in the VFO mode. 19
40
7 SCAN OPERATION
■ Scan types (continued)
MEMORY (SKIP) SCAN (p. 44) BAND MEMORY (SKIP) SCAN (p. 44)
SKIP
Repeatedly scans memory SKIP
Repeatedly scans memory chan-
M1 M2 M3 M1 M2 M3
channels, except those set as 440 MHz
SKIP
nels in the same band as the
M0 M4 M0 M4
SKIP
skip channels. band
440 MHz band currently displayed.
M 249 M6 M5 band
Skip channels can be turned ON
M 249 M6 M5
Example: While scaning the 144 MHz band

or OFF in the select memory
write mode. (p. 46)
ALL/SELECTED BANK SCAN (p. 45) BANK-LINK SCAN (pp. 45, 46)
SKIP Repeatedly scans all bank chan- Repeatedly scans bank channels selected in the “b-LInk”
A00 A01 A02
nels or selected bank channels. item in the Set mode.
A99 A03
SKIP
The skip scan is also available.
A98 A05 A04
DUPLEX SCAN (pp. 42, 44)

During duplex scan operation, repeatedly scans the trans-
mit and receive frequencies of the duplex channel you are
operating on.
41
SCAN OPERATION 7
■ Full/band/programmed scan 1
q Push [V/M/C] to select the VFO mode. t Push [SCAN](H/M/L) to start the scan. 2
• The scan pauses when a signal is received.
• Push [BAND] to select a desired frequency band.
• Rotate [DIAL] to change the scanning direction. This also re-
3
w Set the squelch level.
e Push and hold [SCAN](H/M/L) for 1 sec. to enter the scan sumes scanning. 4
• Push [V/M/C] to stop the scan.
type selection mode.
• Push [BAND] to change the band during band scan, or change
5
r Rotate [DIAL] to select a desired scanning type.
• Select “ALL” for full scan, “bAnd” for band scan, “P-LInk x” for the scan edge during programmed scan/program link scan. 6
programmed link scan (x= 0 to 9), “PROGxx” for programmed • While continuing to push [SCAN](H/M/L) in step e, rotate
[DIAL] to select a desired scanning type, then release the key 7
scan (xx= 0 to 24; only programmed scan edge numbers are
displayed), “dUP” (appears only when duplex operation is set) also starts the scan. 8
for a duplex scan.
9
[DIAL] Push and hold
for 1 sec. 10
Rotate During full/band scan During programmed scan 11
Full scan Programmed scan
12
The scan link name or scan name can be displayed instead
of “P-LInk x” for program link scan (x= 0 to 9), “PROGxx” for 13
programmed scan (xx= 0 to 24) when scan link name or scan
Selectable from “0” to “24,” 14
if programmed. (p. 43) name is programmed and set to ON in the Initial set mode.
Band scan Duplex scan Scan link name or scan name is not displayed during scan. 15
16
17
Programmed link scan
Selectable from “0” to “9.” 18
See page 57 for details
of the programming.
19
42
7 SCAN OPERATION
■ Scan edges programming

Scan edges can be programmed in the same manner as r Rotate [DIAL] to select a desired programmed scan edge
memory channels. Scan edges are programmed into scan channel from 0A to 24A.
edge memory channels, 0A/0b to 24A/24b. t Push and hold [S.MW](V/M/C) for 1 sec. to program.
• 3 beeps sound.
q Push [V/M/C] to select the VFO mode. • The other scan edge channel “b,” 0b to 24b, is automatically se-
w Set a desired frequency: lected when continuing to push [S.MW](V/M/C) after program-
➥ Push [BAND] to select a desired band. ming.
➥ Rotate [DIAL] to set a desired frequency. y To program a frequency for the other pair of scan edges,
➥ Program different frequencies in “✱A” and “✱b.” 0b to 24b, repeat steps w and t.
➥ Set other data (e.g. frequency offset, duplex direction, tone • If the same frequency is programmed into a pair of scan edges,
squelch, etc.), if desired. programmed scan will not function.
e Push and hold [S.MW](V/M/C) for 1 sec. to enter the select
memory write mode.
[EXAMPLE]: Programming 145.300 MHz into scan edges 3A.

[DIAL]
Push and hold Rotate to select Push and hold
for 1 sec. “3A.” for 1 sec.
The VFO mode Enter Return to the VFO mode.

the select memory write mode. “3A” is selected.
43
SCAN OPERATION 7
■ Memory scan 1
IMPORTANT!: To perform a memory scan, 2 or more t Push [SCAN](H/M/L) to start the scan. 2
• The scan pauses when a signal is received.
memory channels MUST be programmed, otherwise the
• Rotate [DIAL] to change the scanning direction. This also re- 3
scan will not start. sumes scanning. 4
q Push [V/M/C] repeatedly to select the memory mode. • Push [V/M/C] to stop the scan.
w Set the squelch level. • While continuing to push [SCAN](H/M/L) in step e, rotate 5
e Push and hold [SCAN](H/M/L) for 1 sec. to enter the scan [DIAL] to select a desired scanning type, then release the key
type selection mode.
6
also starts the scan.
r Rotate [DIAL] to select a desired scanning type. 7
• “ALL” for all memory scan, “bAnd” for band memory scan, “dUP”
(appears only when duplex operation is set) for duplex scan. 8
[DIAL] Push and hold 9
During memory scan
for 1 sec. 10
Rotate
11
All memory scan Duplex scan
12
13
14
Band memory scan
15
16
17
18
19
44
7 SCAN OPERATION
■ Memory bank scan

IMPORTANT!: To perform a memory bank scan, 2 or more r Rotate [DIAL] to select a desired scanning type.
bank channels MUST be programmed, otherwise the scan • Select “ALL” for all bank scan, “b-LInk” for bank link scan or
will not start. “bAnk-x” for bank scan (x= A to Z; only programmed bank
groups are displayed.), “dUP” (appears only when duplex opera-
q Select the memory bank mode. tion is set) for duplex scan.
➥ Push [V/M/C] to select the memory mode. t Push [SCAN](H/M/L) to start the scan.
➥ Push [BAND] to enter the memory bank selection • The scan pauses when a signal is received.
mode. • Rotate [DIAL] to change the scanning direction. This also re-
➥ Rotate [DIAL] to set a desired bank (A to Z), then push sumes scanning.
[BAND]. • Push [V/M/C] to stop the scan.
w Set the squelch level. • Push [BAND] to change the bank during a bank scan.
e Push and hold [SCAN](H/M/L) for 1 sec. to enter the scan • While continuing to push [SCAN](H/M/L) in step e, rotate
type selection mode. [DIAL] to select a desired scanning type, then release the key
also starts the scan.
[DIAL] Push and hold
for 1 sec.
Rotate
All bank scan Bank scan
During all bank/bank link scan During bank scan
emory bank scan skips any memory channels in the se-

M
Selectable from “A” to “Z,” lected bank that are set to “SKIP” or “PSKIP.”
if programmed. (p. 32)
Memory bank scan stops at the first channel when all
Bank link scan Duplex scan
channels in a bank are set to “SKIP” or “PSKIP.”
See page 56 for details of

the bank link programming.
45
SCAN OPERATION 7
■ Skip channel/frequency setting 1

Memory channels can be set to be skipped during memory e Push [SET] repeatedly to select the “SkIP” item. 2
skip scan. In addition, memory channels can be set to be
3
skipped during both memory skip scan and frequency skip
scan. This is useful to speed up the scan rate. 4
q Select a memory channel:
5
Push repeatedly.
➥ Push [V/M/C] to select the memory mode. 6
➥ Rotate [DIAL] to select a desired channel to be a skip
channel/frequency.
7
[DIAL] 8
9
r Rotate [DIAL] to select the skip condition from “SkIP,” 10
“PSkIP” or “OFF” for the selected channel. 11
• PSkIP : The channel is skipped during a memory/bank scan,
and the programmed frequency is skipped during VFO 12
scan, such as a programmed scan.
• SkIP : The channel is skipped during a memory or bank scan. 13
• OFF : The channel is scanned during any scan. 14
w Push and hold [S.MW](V/M/C) for 1 sec. to enter the select t Push and hold [S.MW](V/M/C) for 1 sec. to store the skip
memory write mode. condition into memory. 15
• “ ” or “P ” icon appears, depending on the skip selection
in step r.
16
“ ” appears “ ” appears 17
18
19
Skip channel setting Program skip setting
46
7 SCAN OPERATION
■ Scan resume setting

D Scan pause timer D Scan resume timer
The scan pauses while receiving signals, depending on the The scan restarts after the signal disappears, depending on
scan pause time. It can be set from 2 to 20 seconds or un- the resume time. It can be set from 0–5 seconds or unlim-
limited. ited.
q Push [SET] to enter the Set mode. q Push [SET] to enter the Set mode.
w Rotate [DIAL] to select the scan pause timer item. w Rotate [DIAL] to select the scan resume timer item.
e Rotate [VOL] to select a desired scan pause time from e Rotate [VOL] to select a desired scan resume time from
2–20 seconds (2 seconds steps) or “HOLd.” 0–5 seconds (1 second steps) or “HOLd.”
• “2”–“20” : Scan pauses for 2–20 seconds while receiving a sig- • “0” : Scan restarts immediately after the signal disap-
nal. pears.
• “HOLd” : Scan pauses on a received a signal until it disap- • “1”–“5” : Scan restarts 1–5 seconds after the signal disap-
pears. pears.
• “HOLd” : Scan remains paused on the received signal accord-
ing to the scan pause timer even if it disappears. Ro-
tate [DIAL] to manually resume the scan.
r Push [V/M/C] to return to the frequency display.
he scan resume timer must be set shorter than the scan

T
pause timer, otherwise this timer will not be activated.
47
PRIORITY WATCH 8
■ Priority watch types 1
While operating on a VFO frequency or scanning, the priority 2
MEMORY SCAN WATCH
watch checks for signals on the set priority frequency every
While operating on a VFO fre- 5 seconds 3
5 seconds. The transceiver has four priority watch types to Mch 0
suit your needs.
quency, priority watch checks
SKIP Mch 1
4
for signals on each memory VFO
The watch resumes according to the selected scan resume channel in sequence. frequency Mch 2 5
setting. See page 47 for details. • The memory skip function and/or Mch 249 6
memory bank scan is useful to
OTE: If the pocket beep function is activated, the trans-
N speed up the scan. 7
ceiver automatically selects the tone squelch/DTCS
squelch function when priority watch starts. 8
VFO SCAN WATCH 9
D About priority beep function While scanning in the VFO 5 seconds
mode, priority watch checks for 10
When receiving a signal on the priority frequency, you can be Memory
alerted with beeps and a blink “S” icon. This function can signals on the selected channel VFO
(Call) 11
be activated when the priority watch function is turned ON. every 5 seconds. scan
channel
12
13
14
VFO/MEMORY SCAN WATCH
MEMORY/CALL CHANNEL WATCH While scanning in the VFO 5 seconds
15
While operating on a VFO fre- 5 seconds mode, priority watch checks for Mch 0
16
quency, priority watch checks for SKIP Mch 1
signals on each memory chan- VFO
a signal on the selected channel VFO
Memory
nel in sequence. scan Mch 2 17
(Call)
every 5 seconds. frequency
• A memory channel with skip infor-
channel • The memory skip function and/or Mch 249 18
memory bank scan is useful to
mation can be watched.
speed up the scan. 19
48
8 PRIORITY WATCH
■ Priority watch operation

D Memory/call channel and memory scan watch • During priority watch
q Select the VFO mode, then set an operating frequency.
w Select the channel(s) to be watched.
For memory channel watch:
Select a desired memory channel.
For call channel watch: Monitors VFO frequency Pauses on a memory
for 5 seconds. or call channel when
Select a desired call channel.
a signal is received.
For memory scan watch:
➥ Select the memory mode, or a desired bank group. • During priority watch with priority beep
➥ Push and hold [SCAN](H/M/L) for 1 sec. to enter the
scan type selection mode.
➥ Rotate [DIAL] to select a desired scan type, then push
[SCAN](H/M/L) again to start the memory/bank scan.
e Push [SET] to enter the Set mode. A beep tone sounds and “S” icon blinks when a signal is
r Rotate [DIAL] to select the priority watch set item, then received on a memory or call channel.
rotate [VOL] to select “On.”
• Select “bELL” if the priority beep function is desired.
t Push [V/M/C] to exit the Set mode and start the watch.
• The “PRIO” icon appears.
• The transceiver checks the memory/bank channel(s) or call
channel every 5 seconds.
• The watch resumes according to the selected scan resume set-
ting. (p. 47)
y Push [V/M/C] to cancel the watch.
49
PRIORITY WATCH 8
1
D VFO scan watch 2
q Select the channel(s) to be watched. u Push [SCAN](H/M/L) to start the VFO scan watch. 3
For memory channel watch: • The transceiver checks the memory/bank channel(s) or call
Select a desired memory channel. channel every 5 seconds. 4
For call channel watch: • The watch resumes according to the selected scan resume set-
5
Select a desired call channel. ting. (p. 47)
For memory scan watch: i Push [V/M/C] to cancel the watch. 6
➥ Select the memory mode, or a desired bank group.
➥ Push and hold [SCAN](H/M/L) for 1 sec. to enter the
• During priority watch 7
scan type selection. 8
➥ Rotate [DIAL] to select a desired scan type, then push
[SCAN](H/M/L) again to start memory/bank scan. 9
w Push [SET] to enter the Set mode. Searches VFO frequencies Pauses on a memory 10
e Rotate [DIAL] to select the priority watch set item, then for 5 seconds. or call channel when
rotate [VOL] to select “On.” a signal is received.
11
• Select “bELL” if the priority beep function is desired. 12
• During priority watch with priority beep
13
14
r Push [V/M/C] to exit the Set mode and start the watch. 15
• “PRIO” icon appears. A beep tone sounds and “S” icon blinks when a signal is
t Push and hold [SCAN](H/M/L) for 1 sec. to enter scan type received on a memory or call channel. 16
selection mode. 17
y Rotate [DIAL] to select a desired scan type from “ALL,”
“bAnd,” “P-LInk x (x= 0–9),” “PROGxx (xx= 0–24)” and “dUP.” 18
19
50
9 SET MODES
■ General
D Entering and using the Set mode D Entering and using the Initial set mode
The Set mode is used to change the settings of the trans- The Initial set mode can be accessed at power ON, and al-
ceiver’s functions. lows you to set seldom-changed settings to suit your prefer-
ence and operating style.
w Rotate [DIAL] to select the desired set item. q Push and hold [ ] for 1 sec. to turn the power OFF.
e Rotate [VOL] to set the desired value or option. w While continuing to push [SET], turn the power ON to
r Push [V/M/C] to return to frequency display, or repeat enter the Initial set mode.
steps w and e to set other items. e Rotate [DIAL] to select the desired set item.
r Rotate [VOL] to set the desired value or option.
[DIAL] t Push [ ] to return to the frequency display, or repeat
[VOL]
steps w and e to set other items.
[DIAL]
[VOL]
51
SET MODES 9
■ Set mode item list ■ Initial set mode item list 1

Guidance Item Page Guidance Item Page
2
Repeater tone frequency p. ��
53 Microphone simple mode p. ��
59 3
TSQL frequency p. ��
53 Auto power OFF p. ��
59 4
DTCS code p. ��
53 Display backlight p. ��
60
DTCS polarity p. ��
53 Beep output level p. ��
60
5
Tuning step p. ��
54 Auto repeater p. ��
60 6
Frequency offset p. ��
54 Power save p. ��
61 7
Reverse duplex function p. ��
54 Voltage indication p. ��
61
Operating mode p. ��
54 DTMF speed p. ��
61
8
Weather alert p. ��
54 LCD contrast p. ��
62 9
Priority watch p. ��
55 PTT lock p. ��
62 10
Scan pause timer p. ��
55 Busy lockout p. ��
62
Scan resume timer p. ��
55 Time-out timer p. ��
62
11
Program skip function p. ��
55 Squelch delay p. ��
62 12
Bank link p. ��
56 Monitor key action p. ��
63 13
Programmed scan link p. ��
56 Dial speed acceleration p. ��
63
DTMF TX key p. ��
58 Memory name p. ��
63
14
DTMF memory setting p. ��
58 Scan name p. ��
63 15
MIC gain p. ��
58 Display type p. ��
64 16
VOX function p. ��
58 HS-95 selection p. ��
64
VOX gain p. ��
58 Auto low power p. ��
64
17
VOX delay p. ��
59 18
VOX time-out timer p. ��
59 19
52
9 SET MODES
■ Set mode items

D Repeater tone frequency (R TONE) D DTCS code (CODE)
Selects one of 50 subaudible tone frequencies used to ac- Selects one of 104 DTCS (both encoder/decoder) codes.
cess the repeaters. • 023–754 (default: 023)
• 67.0–254.1 Hz (default: 88.5 Hz)
• Available DTCS codes

023 054 125 165 245 274 356 445 506 627 732
D TSQL frequency (C TONE) 025 065 131 172 246 306 364 446 516 631 734
026 071 132 174 251 311 365 452 523 632 743
Selects one of the tone frequencies for tone squelch or the 031 072 134 205 252 315 371 454 526 654 754
pocket beep function. 032 073 143 212 255 325 411 455 532 662
• 67.0–254.1 Hz (default: 88.5 Hz) 036 074 145 223 261 331 412 462 546 664
043 114 152 225 263 332 413 464 565 703
047 115 155 226 265 343 423 465 606 712
051 116 156 243 266 346 431 466 612 723
053 122 162 244 271 351 432 503 624 731
• Available subaudible tone frequencies D DTCS polarity (DTCS P)

67.0 79.7 94.8 110.9 131.8 156.7 171.3 186.2 203.5 229.1
Selects the DTCS polarity between “both n” (TX/RX: normal),
69.3 82.5 97.4 114.8 136.5 159.8 173.8 189.9 206.5 233.6
71.9 85.4 100.0 118.8 141.3 162.2 177.3 192.8 210.7 241.8 “tn-RR” (TX: normal, RX: reverse), “tR-Rn” (TX: reverse, RX:
74.4 88.5 103.5 123.0 146.2 165.5 179.9 196.6 218.1 250.3 normal) and “both R” (TX/RX: reverse). (default: both n)
77.0 91.5 107.2 127.3 151.4 167.9 183.5 199.5 225.7 254.1 The DTCS code’s polarity for transmitting or receiving can
be independently set by this item.
he transceiver has 50 tone frequencies, and conse-
T
quently their spacing is narrow compared with units hav-
ing 38 tones. Therefore, some tone frequencies may re-
ceive interference from adjacent tone frequencies.
53
SET MODES 9
1
D Tuning step (TS) D Reverse duplex function (DUP.REV) 2
Selects the tuning step between 5, 10, 12.5, 15, 20, 25, 30, Turns the reverse duplex function ON or OFF. (default: OFF) 3
50, 100, 125 and 200 kHz for the dial operation.
4
5
Reverse function is OFF 6
5.0 kHz tuning step
7
The default value may differ, depending on the selected fre- D Operating mode (MODE)
quency band (before accessing the Set mode) and the trans- Sets the operating mode between “WIdE” (FM mode) and
8
ceiver version. “nARROW” (FM-N mode). (default: WIdE) 9
D Frequency offset (OFFSET) 10
Sets the frequency offset for duplex operation (repeater) 11
within the range of 0 to 59.995 MHz. FM mode setting
12
13
D Weather alert (WX.ALT) U.S.A. version only
14
0.600 MHz setting Turns the weather alert function ON or OFF. (p. 72)
(default: OFF) 15
The default value may differ, depending on the selected fre-
quency band (before accessing the Set mode) and trans- 16
ceiver version. 17
he selected tuning step in the VFO mode is used when
T 18
setting the frequency offset.
19
54
9 SET MODES
D Priority watch (PRIO) D Scan resume timer (RESUME)

Activates priority watch or priority watch with priority beep. Selects the scan resume time of a pause after the received
(default: OFF) signal disappears. (default: 2)
• OFF : The priority watch is turned OFF. • 0 : Scan resumes immediately after the received signal
• On :T he transceiver checks the memory channel frequency disappears.
every 5 seconds. • 1–5 : Scan pauses 1–5 seconds after the received signal dis-
• bELL : The transceiver checks the memory channel frequency appears.
every 5 seconds. You can be alerted with beeps and a • HOLd : Scan remains paused on the received signal according
blinking “S” icon. to the scan pause timer, even if it disappears. Rotate
[DIAL] to manually resume the scan.
D Scan pause timer (PAUSE) The scan resume timer must be set shorter than the scan
Selects the scan pause time. When receiving signals, the pause timer (previous item), otherwise this timer will not be
scan pauses according to the scan pause timer. (default: 10) activated.
• 2–20 : Scan pauses for 2–20 seconds while receiving a signal
in 2 seconds steps. D Program skip scan (P SKIP)
• HOLd : Scan pauses on a received signal until it disappears. Turns the programmed skip scan function ON or OFF for
a VFO scan operation (full scan, programmed scan, etc.).
(default: On)
55
SET MODES 9
D Memory bank link function (B-LINK) D Program scan link function (P-LINK) 1
Turns the memory bank link function ON (default) or OFF. Sets the program scan link function. During program scan,
The link function provides continuous bank scan, scanning all link function performs a continuous program scan in the se-
2
channels in the selected banks during bank scan. lected program scan number during program scan. 3
Default settings for LInk0 to LInk9;
PROG 1 to PROG 24 are linked, but PROG 0 is not linked. 4
5
6
• Bank link setting
q P ush and hold [SET] for 1 sec. to enter the bank link 7
• Confirming program scan link
setting. 8
q Rotate [VOL] to select the program scan link number that
you want to confirm. 9
10
w Rotate [DIAL] to select the bank that you want to change 11
the link setting. w Push and hold [SET] for 1 sec. to enter the program scan 12
e Rotate [VOL] to select the option. link setting.
• “LInk” appears.
13
14
Setting is ON Setting is OFF 15
r Rotate [DIAL] to select next bank and repeat steps w e P ush and hold [SET] for 1 sec., then rotate [DIAL] to 16
and e, or push [BAND] to exit the BANK link setting. confirm the linked program scans. 17
18
19
r Push [BAND] twice to exit the program scan link setting.
56
9 SET MODES
• Program scan link setting • Program scan link name programming

q Rotate [VOL] to select the program scan link number that q Rotate [VOL] to select the program scan link number for
you want to change. which you want to program a name.
w Push and hold [SET] for 1 sec. to enter the program scan w Push and hold [SET] for 1 sec. to enter the program scan
link setting. link setting.
e Rotate [DIAL] to select the option, “Add” or “CLEAR.” e Rotate [DIAL] to select “nAmE.”
r P ush and hold [SET] for 1 sec. to enter the name
programming.
r P ush and hold [SET] for 1 sec., then rotate [DIAL] to

select the desired program scan.
• When “Add” is selected in step e, only non-linked program
scans are displayed. When “CLEAR” is selected in step e, only t Rotate [DIAL] to select the desired character, number,
linked program scans are displayed. symbol or space; push [BAND] or [SET] to move the cur-
sor right or left, respectively.
y When the cursor is on the 6th digit, push [BAND] to pro-
gram the scan link name and exit the setting.
t Push and hold [SET] for 1 sec. to set the program scan
link setting.
y Repeat steps r and t to add or clear the program scan u Push [BAND] to exit the program link setting.
to or from the link, or push [BAND] to exit the program i Repeat steps from q to u to program the program link
link scan setting. scan name, or push [V/M/C] to exit the Set mode.
57
SET MODES 9
D DTMF TX key (DTMF-T) D Microphone gain (MIC G) 1

Selects the method to transmit a DTMF code sequence. Sets the microphone gain to between 1 and 4 to suit your
While continueing to push [PTT], push one of the keys, [0] to preference. Higher values make the microphone more sensi-
2
[9], [A](SET), [B](BAND), [C](H/M/L), [D](V/M/C), [M] (indica- tive to your voice. (default: 2) 3
tion: E) or [#] (indication: F).
• KEy : Transmits the appropriate DTMF code assigned to 4
the key. (default)
5
• mEm : Transmits the programmed DTMF code sequence
in the DTMF memory channel assigned to the key. NOTE: When using the VOX function, we recommend 6
• t-CALL : No DTMF code can be transmitted. However, while setting the microphone gain to 3. However, you can adjust
continuing to push [PTT], push [MONI](BAND) to
7
it to suit your operating environment, including the head-
transmit a 1750 Hz tone burst signal. set performance you are using. 8
D VOX function��
(VOX) 9
Turns the VOX function ON or OFF. (p. 80) (default: On) 10
11
D DTMF memory (DTMF)
12
Program the DTMF memory channels. (p. 65)
13
D VOX gain��
(VOX LV)
Sets the VOX gain to between 1 and 10. Higher values make
14
the VOX function more sensitive to your voice. 15
To turn the VOX function OFF, select “OFF.” (default: 5)
16
17
18
NOTE: Set the microphone gain before setting the VOX 19
gain. See page 80 for details of the VOX function.
58
9 SET MODES
■ Initial set mode items

D VOX delay (VOX.DLY) D Microphone simple mode (MIC S)
Sets the VOX delay to between “0.5,” “1.0,” “1.5,” “2.0,” “2.5” Microphone simple mode is used to assign the essential op-
and “3.0” seconds. erations to the four switches (S1 to S4) on the remote con-
The VOX delay is the amount of time the transmitter stays trol unit. (p. 82)
• SImPLE
ON after you stop speaking. (default: 0.5)
• nORm-1 (default)
• nORm-2
D VOX time-out timer (VOXTOT)

Sets the VOX time-out timer to between 1, 2, 3, 4, 5, 10 and D Auto power OFF (AP OFF)
15 minutes to prevent accidental prolonged transmission for
The transceiver can turn itself OFF automatically after a
the VOX function.
specified time. Activating a control restarts the time-out. The
To turn the function OFF, select “OFF.” (default: 3)
transceiver beeps before turning OFF.
30, 60, 90, 120 minutes and OFF can be specified. The spec-
ified period is retained even when the transceiver is turned
OFF by the auto power-off function. To cancel the function,
select “OFF.” (default: OFF)
he VOX time-out timer must be set shorter than the time-
T
out timer, otherwise this timer will not be activated.
59
SET MODES 9
1
D Display backlighting (LIGHT) D Auto repeater (AUTORP) 2
The transceiver has a display backlighting with a 5 second U.S.A. and Korean versions only 3

timer for night time operation. The display backlighting can be 4
The auto repeater function automatically turns the duplex op-
turned ON continuously or turned OFF. (default: Auto1)
eration and tone encoder ON or OFF. The offset and repeater
• OFF : The backlight is turned OFF.
tone settings are not changed by the auto repeater function.
5
• On : The backlight is continuously ON.
• Auto1 : Lights when an operation is performed, then goes out
Reset these frequencies, if necessary. 6
after 5 seconds. U.S.A. version: 7
• Auto2 : Lights when an operation is performed, then goes out • OFF : The auto repeater function is turned OFF.
after 5 seconds with a battery pack or battery case, • R1 :A ctivates for duplex only. (default) 8
• R2 : Activates for duplex and tone.
or stays ON when using the external power supply 9
(more than 10 V DC).
10
11
Korean version:
12
D Beep output level (BEEPLV) • OFF : The auto repeater function is turned OFF. 13
• On :A ctivates for duplex and tone. (default)
Turns the key-touch beep ON or OFF. 14
Sets the beep sound level to between 1 and 9.
(default: 4)
15
16
17
18
19
60
9 SET MODES
D Power save (P SAVE) D Voltage indication (VOLT)

The power save function allows you conserve battery life by The power voltage, battery voltage or external power supply
selecting the duty cycle of the receiver. Select the ratio of the voltage, is displayed at power ON. This setting can be turned
power save time to the standby time. (default: Auto) ON or OFF. (default: On)
• OFF : Turns the function OFF. • OFF : The power voltage display is skipped.
• 2 : Sets the duty cycle to 1:2. • On : The power voltage is displayed at power ON.
• 8 : Sets the duty cycle to 1:8.
• Auto : Transceiver sets
��
“1:2” duty ratio when receiving no
signal for 5 seconds, then it sets “1:16” after 60 sec-
onds has past. D DTMF speed (DTMF-S)
No signal 125 msec. 1000 msec. Select the desired DTMF transmission speed from 100, 200,
5 sec.
Circuit ON 300 or 500 msec. (default: 100)
• 100 : 100 msec. interval; 5.0 characters per second
Circuit OFF
62.5 msec.
60 sec.
• 500 : 500 msec. interval; 1.0 character per second
NOTE: Power save function is disabled when using an ex-

ternal power supply (more than 10 V DC).
61
SET MODES 9
D LCD contrast (CONT) D Time-out timer (TOT) 1

Selects the LCD contrast. (default: Auto) To prevent accidental prolonged transmission, the transceiver
• Auto : Sets the contrast to high. However, if the transceiver is has a time-out timer. This function cuts transmission OFF 2
exposed to high temperatures, it automatically sets the after 1–30 min. of continuous transmission. This timer can be 3
contrast to low. cancelled. (default: 5)
• HI : Sets the contrast to high. • OFF : The time-out timer is turned OFF. 4
• LO : Sets the contrast to low. • 1 to 30 : The transmission is cut OFF after the set period
elapses. 5
6
7
D ��
PTT lock (PTT LK) Approx. 10 seconds before the time-out timer is activated, 8
the transceiver emits a beep tone as a warning. 9
Turns the PTT lock function ON or OFF.
To prevent accidental transmission, the transceiver has the B
E CAREFUL! The transceiver will become hot when this 10
PTT lock function. (default: OFF) time-out timer function is turned OFF or set to a long time
period, and transmission is made for long periods. 11
12
D Squelch delay (SQL DL) 13
Sets the squelch delay between short and long. The delay
D Busy lockout (LK OUT) prevents the squelch from repeatedly opening and closing 14
Turns the busy lockout function ON or OFF. while receiving the same signal. (default: SHORt) 15
This function inhibits transmission while receiving a signal or • SHORt : Sets the squelch delay to short.
when the squelch is open. (default: OFF) • LOnG : Sets the squelch delay to long.
16
17
18
19
62
9 SET MODES
D Monitor key action (MONI) D Memory name (NAME)

The monitor key, [MONI](BAND), can be set as a ‘sticky’ key. The memory name is displayed during memory mode, or the
When set to the sticky condition, each push of [MONI](BAND) memory bank name is displayed during memory bank selec-
toggles the monitor function ON or OFF. (default: PUSH) tion. (default: OFF)
• PUSH : Push and hold [MONI](BAND) to monitor the fre- • OFF : The frequency of the selected memory channel is dis-
quency. played.
• HOLd : Push and hold [MONI](BAND) for 1 sec. to monitor the • On : The pre-programmed memory name or memory bank
frequency and push again to cancel it. name is displayed.
D Scan name (S NAME)

D Dial speed acceleration (DIAL S) The programmed scan, programmed link scan or bank name
The dial speed acceleration automatically speeds up the tun- is displayed during scan type selection. (default: On)
ing dial speed when rotating [DIAL] rapidly. (default: On) • OFF : The programmed scan, programmed link scan or bank
• OFF : The dial speed acceleration is turned OFF. name is not displayed.
• On : The dial speed acceleration is tuned ON. • On : The programmed scan, programmed link scan or bank
name is displayed.
63
SET MODES 9
D Display type (DISP M) D Auto low power (AUTOLP) 1

Selects the display type for memory mode operation. Turns the auto low power function ON or OFF.
(default: FREq) When the temperature goes below 0°C (+32°F), the function
2
• FREq : Displays the programmed frequency. automatically sets the output power to low. 3
• CH :D isplays the memory channel number. Operable func- In that case, the transmit power selections (High/Mid) are
tions, configurable items in the Set mode, and select- also disabled. (default: OFF) 4
able modes will be restricted.
5
• PRIV : D
isplays the memory channel number. Operable chan-
nel, functions and selectable mode are restricted. 6
7
8
9
D Headset selection (HS SEL)
Selects the connected headset type between the HS-95 and
10
other. 11
When using an optional headset HS-95, this setting must be
set to “HS-95.” (default: OtHER) 12
13
14
15
16
17
18
19
64
10 OTHER FUNCTIONS
■ Programming a DTMF code sequence

DTMF codes are used for autopatching, accessing repeat- t Rotate [DIAL] to select the char- [DIAL]
ers, controlling other equipment, etc. The transceiver has 16 acters.
DTMF memory channels (d0–d9, dA, db, dC, dd, dE, dF) for • “0”–“9,” “A,” “b,” “C,” “d,” “E” and “F”
storage of often-used DTMF codes of up to 24 digits. are selectable.
• Up to 24 digits can be programmed.
q Push [SET] to enter the Set mode. • Push [BAND] to move the cursor
w Rotate [DIAL] to select the DTMF programming item. right; push [SET] to move the cur-
e Rotate [VOL] to select a desired DTMF memory channel. sor left.
• If programmed, previously programmed the DTMF code is dis-
played. y Repeat step t until the desired code is input.
[DIAL]
[VOL]
Next display appears after 6th digit has been input.
: 1st display : 2nd display

: 3rd display : 4th display
• If a digit is mistakenly programmed, push [SET] (or [BAND]) re-

Blank channel indication
peatedly to select the digit, then rotate [DIAL] to correct it.
DTMF memory channel
Or rotate [DIAL] to select “_” to erase on and after the digits.
r Push and hold [SET] for 1 sec. to enter the programming Programmed memories will be cleared by this operation on the
mode. 1st digit.
u Push [BAND] twice to program the DTMF code and exit
the programming mode.
The cursor is blinking during • After the 24th digit is input, the transceiver automatically stores
programming mode.
the code sequence and returns to step e.
i Push [V/M/C] to return to the frequency display.
65
OTHER FUNCTIONS 10
■ Transmitting a DTMF code sequence 1

The transceiver has 3 methods of transmitting a DTMF code D Manual DTMF code transmission 2
sequence. Select a desired option in the Set mode.
First, set the DTMF TX key to “kEy” in the Set mode. 3
➥ While continuing to push [PTT], push the desired keys to 4
w Rotate [DIAL] to select the DTMF TX key item.
transmit a DTMF code sequence manually.
[DIAL] • [0]–[9], [A](SET), [B](BAND), [C](H/M/L), [D](V/M/C), [M](.) or 5
[VOL] [#] sends “0”–“9,” “A,” “B,” “C,” “D,” “M” or “#.”
6
7
[PTT] 8
9
10
e Rotate [VOL] to select a desired DTMF key setting.
DTMF code keys 11
• kEy :T ransmits the appropriate DTMF code assigned to the 12
pushed key. (default)
• mEm : T ransmits the programmed DTMF code sequence in the
13
DTMF memory channel assigned to the pushed key. 14
• t-CALL : No DTMF code can be transmitted. However, while
continuing to push [PTT], pushing [MONI](BAND) 15
transmits a 1750 Hz tone burst signal. 16
17
18
19
66
10 OTHER FUNCTIONS
■ Transmitting a DTMF code sequence (continued) ■ Setting DTMF transfer speed

DU
sing a DTMF memory channel The DTMF transfer speed can be selected.
First, set the DTMF TX key to “mEm” in the Set mode. q While continuing to push [SET], turn the power ON to
➥ While continuing to push [PTT], push one of the keys to enter the Initial set mode.
transmit the programmed DTMF code sequence in the w Rotate [DIAL] to select the DTMF transfer speed item,
DTMF memory. then rotate [VOL] to select the transfer speed.
• P ushing [0] to [9], [A](SET), [B](BAND), [C](H/M/L),
[D](V/M/C), [M](.) or [#] transmits “d0”–“d9,” “dA,” “db,” “dC,”
“dd,” “dE” or “dF.”
D1
750 Hz tone 100 : T
ransfer the DTMF tones at about 100 msec. per
o access some European repeaters, the transceiver must
T tone. (default)
transmit a 1750 Hz tone burst signal. 200 : T
ransfer the DTMF tones at about 200 msec per
• This tone can be used as a ‘Call signal’ in countries out of Europe. tone.
First, set the DTMF TX key to “t-CALL” in the Set mode. 300 : T
➥ While continuing to push [PTT], push and hold [MONI] tone.
(BAND) for 1 or 2 sec. to transmit a 1750 Hz tone burst 500 : T
signal. tone.
67
OTHER FUNCTIONS 10
■ Tone frequency and DTCS code 1

D Tone and DTCS squelches D Setting subaudible tones for tone squelch 2
The tone squelch (CTCSS) or DTCS squelch opens only
3
when receiving a signal containing a matching subaudible
tone or DTCS code, respectively. You can silently wait for
w Rotate [DIAL] to select the CTCSS tone frequency item. 4
calls from group members using the same tone or code. [DIAL] 5
Separate tone frequencies can be set for repeater and tone
squelch/pocket beep operation. 6
7
D Reverse tone/DTCS squelch 8
The reverse tone/DTCS squelch is convenient if you want to
ignore a specific signal. The transceiver mutes the squelch 9
when a signal with the matched tone or code is received. 10
“T SQL-R” / “DTCS-R” is displayed when the reverse tone/
DTCS squelch is set. e Rotate [VOL] to select a desired CTCSS tone frequency.
11
• Each operating band and each memory channel have indepen- 12
D Pocket beep dent settings.
13
• See page 53 for available tone frequencies for details.
These functions use subaudible tones or DTCS codes for
calling and can be used as a “common pager” to inform r Push [V/M/C] to return to the frequency display. 14
you that someone has called while you were away from the 15
transceiver.
16
17
18
19
68
10 OTHER FUNCTIONS
■ Tone frequency and DTCS code (continued)
D Setting DTCS code for DTCS squelch D Setting DTCS polarity

q Push [SET] to enter the Set mode. q Push [SET] to enter the Set mode.
w Rotate [DIAL] to select the DTCS code item. w Rotate [DIAL] to select the DTCS polarity item.
[DIAL] [DIAL]
e Rotate [VOL] to select a desired DTCS code. e Rotate [VOL] to select a desired DTCS polarity mode.
• Each operating band and each memory channel have indepen- • both n : Normal phase is used for both TX and RX. (Default)
dent settings. • tn-RR : Normal phase is used for TX; Reverse phase for RX.
• See page 53 for available DTCS codes for details. • tR-Rn : Reverse phase is used for TX; Normal phase for RX.
r Push [V/M/C] to return to the frequency display. • both R : Reverse phase is used for both TX and RX.
TCS phase can be selected in the “dtCS P” item. See
D
next content for more details.
69
OTHER FUNCTIONS 10
■ Tone/DTCS squelch 1
q S et a desired operating frequency, and then set a No tone operation Subaudible tone encoder 2
CTCSS tone or DTCS code.
3
w Push and hold [TONE](0) for 1 sec. repeatedly to activate
the tone or DTCS squelch. (T SQL or DTCS) 4
• S ubaudible tone encoder “T,” pocket beep (tone squelch)
“ST SQL,” tone squelch “T SQL,” DTCS beep “SDTCS,” Pocket beep Tone squelch 5
DTCS squelch “DTCS,” tone squelch reverse “T SQL-R,” DTCS 6
squelch reverse “DTCS-R” and no tone operation are select-
able in order.
7
• While continuing to push [TONE](0), rotate [DIAL] also selects
DTCS beep DTCS squelch 8
a tone setting.
e Operate the transceiver in the normal way. 9
r When the received signal includes a matching tone/code, 10
the squelch opens and the signal can be heard.
When the pocket beep function is activated, the trans- Tone squelch (reverse) DTCS squelch (reverse) 11
ceiver also emits beep tones and blinks “�S.” 12
• When the received signal’s tone/code does not match, tone/
DTCS squelch does not open, however, the S-indicator shows 13
signal strength.
• To open the squelch manually, push and hold [MONI](BAND).
14
t Push [PTT] to answer or push and hold [MONI](BAND) 15
for 1 sec. to stop the beeps and blinking.
16
17
18
19
70
10 OTHER FUNCTIONS
■ Tone scan
The transceiver can detect the subaudible tone frequency
and DTCS code in a received signal. By monitoring a signal
that is being transmitted on a repeater input frequency, you
can determine the tone frequency required to access the re-
peater. Tone scan for repeater tone
q S et the desired frequency or memory channel to be

checked for a tone frequency or DTCS code.
w Push and hold [TONE](0) for 1 sec. repeatedly to activate
the repeater tone, tone squelch or DTCS squelch. (T, Tone scan for tone squelch
T SQL or DTCS)
e Push and hold [T.SCAN](#) for 1 sec. to start the tone
scan.
• To change the scanning direction, rotate [DIAL].
Tone scan for DTCS squelch
r When the tone frequency or DTCS code is decoded, the
set mode contents are programmed with the frequency or
code. t Push [V/M/C] to stop the scan.
• If the scan is cancelled before the transceiver detects the tone
• The tone scan pauses for the set period in scan pause timer
or code, the set mode contents are not changed.
(p. 47) when a tone frequency or DTCS code is detected.
• T he detected tone is used for temporary operation only.
• The decoded tone frequency is used for the repeater tone fre-
The stored tone setting in memory or call channel won’t be
quency when any tone setting, such as repeater tone or tone
changed.
squelch is OFF.
• The decoded tone frequency is used for the tone squelch fre-
quency when the tone squelch is ON.
• The decoded DTCS code is used for the DTCS squelch code NOTE: Tone frequency is over-written automatically when
when the DTCS squelch is ON. it corresponds with the scanning tone frequency in tone
squelch mode. However, it is not over-written in memory or
call channel mode.
71
OTHER FUNCTIONS 10
■ Weather channel operation U.S.A. version only 1

There are 10 weather channels for monitoring D Weather alert function 2
weather broadcasts from the NOAA (National
NOAA broadcast stations transmit weather alert tones be- 3
Oceanic and Atmospheric Administration).
fore important weather announcements. When the weather
alert function is turned ON, the selected weather channel is
4
D Weather channel selection monitored every 5 seconds for the announcement. When the 5
q P ush [V/M/C] repeatedly to select weather channel alert signal is detected, the “ALT” and the WX channel in-
dications are displayed alternately and a beep sounds until 6
mode.
• The weather channel number appears. the transceiver is operated. The previously selected (used) 7
w Rotate [DIAL] to select a desired weather channel. weather channel is checked periodically during standby or
e Push [V/M/C] to return to the previous frequency or mem- while scanning. 8
ory channel.
q Select the desired weather channel.
9
[DIAL] w Push [SET] to enter the Set mode. 10
e Rotate [DIAL] to select the weather alert setting item, then
Weather channel dysplay rotate [VOL] to select “On.” 11
12
13
14
r Push [V/M/C] to return to the weather channel display.
• “WX” appears. 15
16
ush and hold [SCAN](H/M/L) for 1 sec. activates the
P
weather channel scan. Push [SCAN](H/M/L) again to stop 17
the scan. 18
Appears
19
72
10 OTHER FUNCTIONS
D Weather alert function (continued)

t Set the desired stand-by condition.
• Select the VFO mode, memory mode or call channel mode.
• Scan or priority watch operation can also be selected.
y When the alert is detected, a beep sounds and the follow-
ing indication is displayed.
Shows above indications alternately.
u Turn the weather alert function OFF in the Set mode.
OTE: While receiving a signal on a frequency other than

N
the Weather alert frequency, the receiving signal will be
interrupted momentarily approximately every 5 seconds
when the Whether alert function is ON. These interrup-
tions cease when the Weather alert function is turned
OFF.
73
OTHER FUNCTIONS 10
■ Cloning function 1
The IC-T70A/T70E has transceiver-to-transceiver data clon- e Push [PTT] on the “master” transceiver. 2
ing capability. This function is useful when you want to copy • “CL Out m” appears and the bar meter shows that cloning is
3
all of the programmed contents from one IC-T70A/T70E to taking place.
another. • After the cloning is completed, the display returns to “CLOnE 4
• An optional OPC-474 cloning cable is required. m.”
r Push and hold [ ] for 1 sec. to turn power OFF.
5
q Turn the transceiver’s power OFF, then connect an optional 6
OPC-474 between both [SP] jacks.
7
OPC-474
to the [SP] jack to the [SP] jack
The optional CS-T70 CLONING SOFTWARE is also available 8
to clone/edit contents with a PC (for Microsoft ® Windows®
2000/XP, Windows Vista® or Windows® 7) using ICF format 9
files. 10
11
to the OPC-478UC
[SP] jack (USB type) to USB port 12
13
w W h i l e c o n t i n u i n g t o p u s h
[V/M/C], push and hold [ ] for OPC-478 to RS-232C 14
(RS-232C type) port
1 sec. to enter the cloning mode. 15
• “CLOnE m” appears.
PC 16
17
18
19
74
10 OTHER FUNCTIONS
■ Resetting
The display may occasionally display D All reset D Partial reset
erroneous information (e.g. when first q Push and hold [ ] for 1 sec. to turn q Push and hold [ ] for 1 sec. to turn
applying power). This may be caused power OFF. power OFF.
externally by static electricity or by w W hile continuing to push [SET], w W hile continuing to push [H/M/L],
other factors. [BAND] and [H/M/L], then turn then turn power ON to par tially
power ON to reset the CPU. reset the transceiver.
If this problem occurs, turn power OFF.
• “CLEAR” appears when resetting the
After waiting a few seconds, turn power CPU (See the illustration below). NOTE: No message appears on the
ON again. If the problem persists, per- display after the partial reset is done.
form either or both procedures below.
All reset
• All reset
Reset the CPU before operating the
transceiver for the first time, or if the
internal CPU malfunctions due to static
electricity, etc. All reset clears all pro-
gramming and returns all settings to
their factory defaults.
• Partial reset
Use Partial reset if you want to initial- Partial reset
ize the operating conditions (VFO
frequency, VFO settings, set mode
contents) without clearing the memory
contents.
C
AUTION: Resetting the CPU re-
turns all programmed contents to
their default settings.
75
TROUBLESHOOTING 11
If your transceiver seems to be malfunctioning, please check the following points before sending it to a service center. 1
PROBLEM POSSIBLE CAUSE SOLUTION REF.
2
Transceiver does not turn • The battery is exhausted. • Charge the battery pack, or replace the batteries. pp. 2, 11–14
ON. • The battery polarity is reversed. • Check the battery polarity. p. 11 3
•L oose connection of a battery pack (case). • Clean battery terminals. –
No sound comes from the • Volume level is too low. • Rotate [VOL] to adjust to a desired level. p. 16
4
speaker. • An external speaker or a cloning cable is con- • Check the external speaker connection or remove – 5
nected to the [SP] jack. the cloning cable.
Transmitting is impossible. • A frequency outside of the 144/440 MHz ama- • Set the frequency within 144/440 MHz amateur p. 20 6
teur bands is set. bands. 7
• The PTT lock function is activated. • Set the PTT lock function OFF in the Initial set mode. p. 62
• The heat protection is activated, and “Hot” is • Cool down the transceiver. p. 23 8
displayed.
Transmitting using the VOX • The VOX gain is set to OFF or too low. •S et the VOX gain to a suitable level. p. 81
9
function is impossible. •T he microphone gain is too low. • Set the microphone gain to a suitable level. p. 58 10
Contacting with another • Different tone or code is used for the tone/ • Check the tone/DTCS by performing a tone scan. p. 71
station is impossible. DTCS squelch.
11
Frequency cannot be set. • The lock function is activated. • Push and hold [ ](SET) for 1 sec. to cancel the p. 21 12
lock function.
• The memory mode, Call channel mode, or • Push [V/M/C] repeatedly to select the VFO mode. p. 18
13
weather channel mode is selected. 14
A program scan does not • The memory mode, Call channel mode, or • Push [V/M/C] repeatedly to select the VFO mode. p. 18
start. weather channel mode is selected. 15
• The same frequency has been programmed in • P
rogramming different frequencies in the scan edge p. 43 16
the scan edge channels, “✱A” and “✱b.” channels.
A memory scan does not • The VFO mode or Call channel mode is selected. • Push [V/M/C] repeatedly to select the memory mode. p. 18 17
start. • Only one or no memory channel has been pro- • Program 2 or more memory channels. p. 31
grammed.
18
The displayed frequency is • The CPU has malfunctioned. • Reset the transceiver. p. 75 19
erroneous. • External factors have caused a fault. • Remove and re-attach the battery pack/case. p. 2
76
12 SPECIFICATIONS
D General D Transmitter
• Frequency coverage : (unit: MHz) • Modulation system : Variable reactance freq. modulation
Version TX RX • Output power (at 7.2 V DC) : H
igh 5.0 W, Mid. 2.5 W, Low 0.5 W
EUR, KOR 144–146, 430–440 144–146, 430–440 (typical)
UK, RSP 144–146, 430–440 136–174*1, 400–479*2 • Max. frequency deviation : ±5.0 kHz (FM wide: approx.)
U.S.A. 144–148, 420–450*4 136–174*3, 400–479*4 ±2.5 kHz (FM narrow: approx.)
TPE 144–146, 430–432 144–146, 430–432 • Spurious emissions : Less than –60 dBc at High/Mid.
AUS 144–148, 420–450*2 136–174*3, 400–479*2 Less than –13 dBm at Low
CHN, EXP 136–174*3, 400–479*2 136–174*3, 400–479*2 • Ext. mic. impedance : 2.2 kW
*1Guaranteed 144–146 MHz only, *2Guaranteed 430–440 MHz only,
*3Guaranteed 144–148 MHz only, *4Guaranteed 440–450 MHz only D Receiver
• Mode : FM, FM-N
• Receive system : Double-conversion superheterodyne
• No. of memory channels : 302
• Intermediate frequencies : 1st 46.35 MHz, 2nd 450 kHz
(incl. 50 scan edges and 2 call channels)
• Sensitivity (except spurious points, 1 kHz/3.5 kHz Dev.; 12 dB SINAD) :
• Usable temp. range : –20°C to +60°C; –4°F to +140°F
Guaranteed freq. range Less than 0.18 µV
• Tuning steps : 5 , 10, 12.5, 15, 20, 25, 30, 50, 100,
Other freq. range Less than 0.32 µV
125 and 200 kHz
• Squelch Sensitivity (except spurious points, 1 kHz/3.5 kHz Dev.) :
• Frequency stability : ±2.5 ppm (–20°C to +60°C; –4°F to +140°F)
Guaranteed range Less than 0.18 µV
• Power supply : 10.0–16.0 V DC for external DC power,
Other frequency range Less than 0.32 µV
or specified Icom battery pack
• Audio output power : (at 10% distortion/7.2 V DC)
• Current drain (at 7.2 V DC) :
Internal speaker More than 700 mW with a 16 W load
TX High (typical) VHF 1.7 A, UHF 2.1 A
External speaker More than 400 mW with an 8 W load
Mid. (typical) VHF 1.2 A, UHF 1.5 A
• Selectivity : (at CH spacing 20 kHz/in the amateur bands)
Low (typical) VHF 0.6 A, UHF 0.8 A FM (Wide) More than 60 dB
Rx Max. output Less than 450 mA (Internal speaker)
FM (Narrow) More than 60 dB
Less than 300 mA (External speaker)
• Ext. speaker connector : 3-conductor 3.5(d) mm; (1⁄8˝)/8 W
Power save Less than 40 mA (Duty 1:8)
• Spurious and image rejection ratio (in guaranteed freq. range) :
standby Less than 90 mA
More than 60 dB
• Antenna connector : SMA (50 W)
• Dimensions : 58(W)×111(H)×30(D) mm;
(projections not included) 29⁄32(W)×43⁄8(H)×13⁄16(D) in
• Weight (approx.) : 380 g; 13.4 oz (with antenna and BP-264) All stated specifications are subject to change without notice or obligation.
77
OPTIONS 13
• BP-263 battery case BC-191/BC-193 common specifications 1
Battery case for LR6 (AA) × 6 alkaline batteries. Power supply voltage 12 to 16 V DC or the specified
• BP-264 ni-mh battery pack Icom AC adapter (BC-123S) 2
7.2 V/1400 mAh (Typ.) Ni-MH battery pack. Battery life:
Charging temp. range +10°C to +40°C; 3
11.5 hrs. (approx.; VHF, FM, high power, Tx : Rx : Standby
+50°F to +104°F 4
= 5:5:90)
Same as supplied one. (Not supplied with some version.) Dimensions 87.5(W)×53.7(H)×72.8(D) mm;
(projections not included) 37⁄16(W)×21⁄8(H)×27⁄8(D) in
5
• BP-265 li-ion battery pack
7.4 V/1900 mAh (Min.)/2000 mAh (Typ.) Lithium Ion battery 6
• BC-192 desktop charger+BC-147S ac adapter
pack. Battery life: 16 hrs. (approx.; VHF, FM, high power, Tx For regular charging of the Ni-MH battery pack, BP-264. An 7
: Rx : Standby = 5:5:90) AC adapter may be supplied with the charger, depending
• BC-123S ac adapter on the version.
8
AC adapter for the desktop charger, BC-191 or BC-193. Charging time: Approx. 16 hours for the BP-264. 9
• BC-147S ac adapter BC-192 specifications
10
AC adapter for the desktop charger, BC-192. Power supply voltage* 12 to 16 V DC or the specified
• BC-167S battery charger Icom AC adapter (BC-147S) 11
For regular charging of the Ni-MH battery pack, BP-264. Charging temp. range 0°C to +45°C; 12
Same as supplied one. (Not supplied with some version.) 32°F to +113°F
• BC-191 desktop charger+BC-123S ac adapter
13
Dimensions 87.5(W)×53.7(H)×72.8(D) mm;
For rapid charging of the Ni-MH battery pack, BP-264. An (projections not included) 37⁄16(W)×21⁄8(H)×27⁄8(D) in 14
AC adapter may be supplied with the charger, depending
on the version. * Charging time differs depending on the input voltage. 15
12 V : Approx. 36 hours
Charging time: Approx. 2 hours for the BP-264.
13.8 V : Approx. 21 hours 16
• BC-193 desktop charger+BC-123S ac adapter 16 V : Approx. 16 hours
For rapid charging of the Li-Ion battery pack, BP-265. An
17
AC adapter may be supplied with the charger, depending 18
on the version.
Charging time: Approx. 2.5 hours for the BP-265.
19
78
13 OPTIONS
• CP-12L cigarette lighter cable with noise filter • HS-94/HS-95/HS-97 headset

• CP-19R cigarette lighter cable with dc-dc converter +OPC-2006 plug adapter cable
Allows you to operate the transceiver through a 12 V ciga- HS-94 : Ear hook type
rette lighter socket. You can also charge the attached bat- HS-95 : Neck & arm type
tery pack (during stand-by only). HS-97 : Throat microphone
CP-19R: A built-in DC-DC converter provides an 11 V DC OPC-2006 : Allows you to connect the HS-94/HS-95/HS-97
output. to the transceiver. After connecting, the VOX
• CP-23L cigarette lighter cable function can be used.
Allows charging of the battery packs through a 12 V ciga- • SP-27 tube earphone
rette lighter socket. (For BC-191/BC-193) Provides clear audio in noisy environments.
• OPC-254L dc power cable • OPC-474 cloning cable
For operation and charging via an external power supply. For transceiver-to-transceiver cloning.
• OPC-515L dc power cable • OPC-478/OPC-478UC cloning cable
Allows charging of the battery packs using a 12 V DC Used for data cloning between transceiver and PC with
power source instead of the AC adapter. (For BC-191/ CS-T70 (cloning software).
BC-192/BC-193) • CS-T70 cloning software
• AD-92SMA antenna connector adapter Provides quick and easy programming of such settings as
Allows you to connect an external antenna with a BNC memory channels and Set modes contents via your PC’s
connector. RS-232C terminal (using OPC-478), or USB port (OPC-
• HM-131 speaker-microphone 478UC). Either OPC-478 or OPC-478UC is required.
Combination speaker-microphone that provides convenient • LC-174 carrying case
operation while hanging the transceiver on your belt. Helps protect the transceiver from scratches, etc.
• HM-153 earphone-microphone
Ideal for hands-free operation: clip the HM-153 (with inte- Approved Icom optional equipment is designed for optimal
grated PTT switch) to your lapel or breast pocket. performance when used with an Icom transceiver.
Icom is not responsible for the destruction or damage to an
Icom transceiver in the event the Icom transceiver is used with
equipment that is not manufactured or approved by Icom.
79
OPTIONS 13
■ VOX function 1
The transceiver has a VOX function, which allows hands-free D Turning the VOX function ON or OFF 2
operation.
q Connect an optional headset and plug adapter cable to the 3
An optional HS-94, HS-95 or HS-97 headset and the
transceiver, and then turn the power ON.
OPC-2006 plug adapter cable are also required for operation.
w Push [SET] to enter the Set mode.
4
• The VOX (voice operated transmission) function starts transmis-
sion when you speak into the microphone, without needing to
e Rotate [DIAL] to select the VOX setting item, then rotate 5
[VOL] to select “On.”
push [PTT]; then, automatically returns to reception when you stop 6
speaking.
7
D Optional unit connection 8
q Push and hold [ ] for 1 sec. to turn the power OFF.
w Remove the jack cover.
r Push [V/M/C] to return to the frequency display. 9
• “ VOX” appears when the VOX function is ON.
e Connect the optional HS-94, HS-95 or HS-97 and OPC- 10
2006, as illustrated below. NOTE:
•W hen using the VOX function, adjust the microphone gain
11
OPC-2006
and the VOX-related settings (p. 81) to suit your operating 12
environment (including your headset performance).
• Select the headset type between the HS-95 and other in
13
the Initial set mode. (p.64) 14
HS-94 • Set the microphone gain before setting the VOX gain in
the Set mode (p. 58). We recommend setting the micro- 15
phone gain to 3. 16
•W hen the PTT lock is set to “On” in the Set mode, you
cannot transmit using the VOX function. (p. 62) 17
Transceiver 18
19
80
13 OPTIONS
D VOX-related settings
The VOX gain, the VOX delay, and the VOX time-out timer
• VOX delay
can be set in the Set mode.
Sets the VOX delay to between 0.5 and 3.0 seconds (in 0.5
q Connect an optional headset and plug adapter cable to the sec. steps). The VOX delay is the amount of time the transmit-
transceiver, and then turn the power ON. ter stays ON after you stop speaking. (default: 0.5)
w Push [SET] to enter the Set mode.
e Rotate [DIAL] to select the VOX gain (VOX LV), the VOX
delay (VOX.dLy), or the VOX time-out timer (VOX.tot) item.
r Rotate [VOL] to select a desired option.
t Push [V/M/C] to exit the Set mode.
If “VOX” is intermittent, be sure the VOX delay is set long
The VOX function does not activate transmission while in enough to allow normal pauses in speech, but keep the
the Set mode. VOX ON until you finish speaking.
• VOX gain • VOX time-out timer
The VOX gain level can be adjusted between 1 (minimum) Sets the VOX time-out timer to between 1, 2, 3, 4, 5, 10 and
and 10 (maximum), or turned OFF. Higher values make the 15 minutes to prevent accidental prolonged transmission for
VOX function more sensitive to your voice. (default: 5) the VOX function.
To turn the function OFF, select “OFF.” (default: 3)
➥ While speaking into the headset microphone, adjust the

VOX gain until “VOX” continuously appears on the LCD.
he VOX time-out timer must be set shorter than the time-
T
✔ CONVENIENT! out timer, otherwise this timer will not be activated.
While transmitting using the VOX function, you can adjust the
VOX gain simply by rotating [DIAL].
81
OPTIONS 13
■ Remote control function 1

The remote control unit allows you to remotely select operat- • SIMPLE 2
ing frequencies, memory channels, etc. S1 Selects the Call channel.
S2 Turns the monitor function ON or OFF. 3
•U
ser remote control unit S3 Selects memory channel 0. 4
The illustrated circuit is for reference only. S4 Selects memory channel 1.
5
to the [SP] jack
REMOTE 3.5(d) mm
• NORM-1 6
2.7kΩ 6.8kΩ 15kΩ 33kΩ S1 Toggles the VFO mode and the memory mode.
S2 Selects the Call channel. 7
S1 S2 S3 S4 SP
+ S3 Frequency or memory channel “UP.” 8
GND – S4 Frequency or memory channel “DOWN.”
EXTERNAL SPEAKER 9
Rated input >
‗ 700 mW (8 Ω)
• NORM-2
S1 Toggles the VFO mode and the memory mode.
10
B
e sure to turn power OFF when plugging/unplugging the
remote control unit to/from the [SP/MIC] jack. S2 Turns the monitor function ON or OFF. 11
S3 Frequency or memory channel “UP.”
S4 Frequency or memory channel “DOWN.” 12
D Simple remote control mode
13
q While continuing to push [SET], turn the power ON to he VFO mode cannot be selected via the remote control
T
enter the Initial set mode. unit when SIMPLE mode is selected. 14
w Rotate [DIAL] to select the microphone simple mode
15
item. • COMMON (SIMPLE/NORM-1/NORM-2)
e Rotate [DIAL] to select “SImPLE,” “nORm-1” or “nORm-2” S2 Transmits T-CALL (1750 Hz tone) while pushing [PTT]. 16
option. S3 Volume “UP” while operating the monitor function. 17
S4 Volume “DOWN” while operating the monitor function.
18
r Push [ ] to return to the frequency display.
19
82
14 CE
IMPORTANT
• When transmitting with a portable radio, hold the radio in • List of Country codes (ISO 3166-1)
a vertical position with its microphone 2.5 to 5 centimetres
from your head and body. Country Codes Country Codes
1 Austria AT 18 Liechtenstein LI
• If you wear a portable two-way radio on your body, ensure 2 Belgium BE 19 Lithuania LT
that the antenna is at least 2.5 centimetres from your body 3 Bulgaria BG 20 Luxembourg LU
when transmitting. 4 Croatia HR 21 Malta MT
5 Czech Republic CZ 22 Netherlands NL
C
E Versions of the IC-T70E which display 6 Cyprus CY 23 Norway NO
the ‘CE’ symbol on the serial number label, 7 Denmark DK 24 Poland PL
comply with the essential requirements of the 8 Estonia EE 25 Portugal PT
European Radio and Telecommunication Ter- 9 Finland FI 26 Romania RO
minal Directive 1999/5/EC. 10 France FR 27 Slovakia SK
11 Germany DE 28 Slovenia SI
This warning symbol indicates that this equip- 12 Greece GR 29 Spain ES
ment operates in non-harmonised frequency 13 Hungary HU 30 Sweden SE
bands and/or may be subject to licensing con- 14 Iceland IS 31 Switzerland CH
ditions in the country of use. Be sure to check 15 Ireland IE 32 Turkey TR
that you have the correct version of this radio 16 Italy IT 33 United Kingdom GB
or the correct programming of this radio, to 17 Latvia LV
comply with national licensing requirements.
83
CE 14
1
DECLARATION 2
OF CONFORMITY 3
4
We Icom Inc. Japan 5
1-1-32, Kamiminami, Hirano-ku
Osaka 547-0003, Japan 6
Declare on our sole responsibility that this equipment complies with the 7
essential requirements of the Radio and Telecommunications Terminal
Equipment Directive, 1999/5/EC, and that any applicable Essential Test
Bad Soden 18th Dec. 2009
8
Place and date of issue
Suite measurements have been performed.
9
Kind of equipment: VHF/UHF DUAL BAND FM TRANSCEIVER Icom (Europe) GmbH
Communication Equipment
Auf der Krautweide 24,
10
Type-designation: iC- t70e 65812 Bad Soden am Taunus,
Germany
11
Authorized representative name 12
Version (where applicable):
Y. Furukawa 13
This compliance is based on conformity with the following harmonised
General Manager
standards, specifications or documents: 14
i) EN 301 489-1 v1.6.1 (September 2005)
ii) EN 301 489-15 v1.2.1 (August 2002) 15
iii) EN 301 783-2 v1.1.1 (September 2000)
iv) EN 60950-1 (2001): A11: 2004
16
Signature 17
18
19
84
INDEX
–1– Charging caution·············································································10

1750 Hz tone···················································································28 Charging note············································································12, 13
Checking the repeater input signal··················································25
–A– Cloning function···············································································74
All reset····························································································75 Copying call channel contents·························································37
Antenna·····························································································2 Copying memory contents·······························································37
Auto low power (AUTOLP)·······························································64
Auto power OFF (AP OFF)······························································59 –D–
Auto repeater (AUTORP)·································································60 DC operating note···········································································15
Auto repeater function·····································································27 Desktop battery chargers································································13
Dial speed acceleration (DIAL S)····················································63
–B– Display backlighting (LIGHT)···························································60
Band scan (VFO mode)···································································42 Display type·····················································································36
Battery caution················································································10 Display type (DISP M)·····································································64
Battery icons····················································································12 DOC·································································································84
Battery information··········································································11 DTCS code (CODE)········································································53
Battery life························································································11 DTCS polarity (DTCS P) ································································53
Battery pack······················································································2 DTCS squelch·················································································70
Beep output level (BEEPLV)····························································60 DTMF memory (DTMF)···································································58
Belt clip······························································································1 DTMF speed (DTMF-S)···································································61
Busy lockout (LK OUT)····································································62 DTMF TX key (DTMF-T)··································································58
Duplex operation·············································································26
–C–
Call channel mode···········································································18 –E–
Call channel watch··········································································49 Entering and using the Initial set mode···········································51
Caution (for the optional BP-265 Li-Ion battery pack)·······················9 Entering and using the Set mode····················································51
Caution (for the supplied BP-264 Ni-MH battery pack)·····················8 Erasing bank contents·····································································39
CE····································································································83 Explicit definitions··············································································· i
Channel number display··································································36 External DC power operation··························································15
85
INDEX
–F– –L–
1
FCC information··············································································· iii LCD contrast (CONT)······································································62
Features····························································································· i List of Country codes (ISO 3166-1)·················································83 2
Foreword····························································································· i
3
Frequency display············································································36 –M–
Frequency offset (OFFSET)····························································54 Memory bank link function (B LINK)················································56 4
Frequency range and offset direction··············································27 Memory bank scan··········································································45
5
Front panel························································································3 Memory bank selection···································································33
Full scan··························································································42 Memory bank setting·······································································32 6
Function display·················································································6 Memory channel contents·······························································29
7
Memory channel programming························································31
–G– Memory channel watch···································································49 8
General description·········································································29 Memory clearing··············································································38
9
Memory mode·················································································18
–H– Memory name (NAME)····································································63 10
Hand strap·························································································1 Memory scan ··················································································44
11
Headset selection (HS SEL)····························································64 Memory scan watch········································································49
Microphone gain (MIC G)································································58 12
–I– Microphone simple mode (MIC S)···················································59
13
Important···························································································· i Monitor function···············································································17
Index··························································································85–88 Monitor key action (MONI)·······························································63 14
Initial set mode item list···································································52
15
Initial set mode items·······································································59 –O–
Off band indication···········································································25 16
–K– Operating mode (MODE)·································································54
17
Key lock function··············································································21 Operating mode selection································································21
Keypad·······························································································4 Optional battery case······································································11 18
Optional unit connection··································································80
19
Options······················································································78–82
86
INDEX
–P– Resetting·························································································75
Partial reset·····················································································75 Reverse duplex function (DUP.REV)···············································54
Pocket beep·····················································································68 Reverse tone/DTCS squelch···························································68
Power OFF······················································································16 Reverse duplex function··································································26
Power ON························································································16
Power save (P SAVE)······································································61 –S–
Precautions····················································································ii, iii Scan edges programming·······························································43
Priority watch (PRIO)·······································································55 Scan name (S NAME)·····································································63
Priority watch operation···································································49 Scan pause timer·············································································47
Priority watch types·········································································48 Scan pause timer (PAUSE)······························································55
Private channel display····································································36 Scan resume setting········································································47
Program scan link function (P LINK)···············································56 Scan resume timer··········································································47
Program skip scan (P SKIP)····························································55 Scan resume timer (RESUME)························································55
Programmed scan ··········································································42 Scan types·······················································································40
Programming a DTMF code sequence············································65 Selecting a call channel···································································29
Programming bank name································································34 Selecting a memory channel···························································30
Programming memory name···························································34 Selecting bank name indication·······················································35
Programming scan name································································34 Selecting memory name indication·················································35
PTT lock (PTT LK)···········································································62 Selecting the mode··········································································18
Set mode item list············································································52
–R– Set mode items················································································53
Rapid charging with the BC-191······················································13 Setting audio volume·······································································16
Rapid charging with the BC-193······················································14 Setting DTCS code for DTCS squelch············································69
Receiving·························································································22 Setting DTCS polarity······································································69
Regular charging·············································································12 Setting DTMF transfer speed··························································67
Regular charging with the BC-192···················································14 Setting duplex direction···································································26
Remote control function···································································82 Setting frequency offset···································································26
Repeater operation··········································································24 Setting subaudible tone for tone squelch········································68
Repeater tone frequency (R TONE)················································53 Setting the frequency using the dial················································19
87
INDEX
Setting the frequency using the keypad··········································20 –U–

1
Setting the squelch level··································································17 Usable characters············································································34
Setting the tuning step·····································································19 2
Side panel··························································································3 –V –
3
Skip channel setting········································································46 VFO mode·······················································································18
Skip frequency setting·····································································46 VFO scan watch··············································································50 4
Specifications··················································································77 Voltage indication (VOLT)································································61
5
Squelch delay (SQL DL)··································································62 VOX delay (VOX.DLY)······································································59
Supplied accessories······································································· iv VOX function····················································································80 6
VOX function (VOX)·········································································58
7
–T – VOX gain (VOX LV)··········································································58
Table of contents···········································································v, vi VOX time-out timer (VOXTOT)·························································59 8
Time-out timer (TOT)·······································································62 VOX-related settings········································································81
9
Tone and DTCS squelches······························································68
Tone frequency and DTCS code·····················································68 –W – 10
Tone scan························································································71 Weather alert (WX.ALT)··································································54
11
Tone squelch···················································································70 Weather alert function·····································································72
Top panel···························································································3 Weather channel mode···································································18 12
Transferring bank contents······························································39 Weather channel operation·····························································72
13
Transmit power selection·································································22 Weather channel scan·····································································72
Transmit warning·············································································23 Weather channel selection······························································72 14
Transmitting·····················································································23
15
Transmitting a DTMF code sequence··············································66
Troubleshooting···············································································76 16
TSQL frequency (C TONE)······························································53
17
Tuning step (TS)··············································································54
Tuning step selection·······································································19 18
Turning the VOX function ON or OFF··············································80
19
88
#02 EUR <Intended Country of Use>
■ AT ■ BE ■ CY ■ CZ ■ DK ■ EE
■ FI ■ FR ■ DE ■ GR ■ HU ■ IE
■ IT ■ LV ■ LT ■ LU ■ MT ■ NL
■ PL ■ PT ■ SK ■ SI ■ ES ■ SE
■ GB ■ IS ■ LI ■ NO ■ CH ■ BG
■ RO ■ TR ■ HR
#03 UK <Intended Country of Use>

#12 RSP <Intended Country of Use>

A-6808H-1EX-q
Printed in Japan
© 2009–2010 Icom Inc.
Printed on recycled paper with soy ink. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan

Amateur - IC-T70A Instruction Manual PDF

Uploaded by

Copyright:

Available Formats

Amateur - IC-T70A Instruction Manual PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Amateur - IC-T70A Instruction Manual PDF

Uploaded by

Copyright:

Available Formats

INSTRUCTION MANUAL

VHF/UHF DUAL BAND FM TRANSCEIVER

This device complies with Part 15 of the FCC Rules. Operation is

CAUTION: Changes or modifications to this device, not

■ Hand strap ■ Belt clip

To detach the belt clip:

■ Battery pack ■ Antenna 1

■ Front, top and side panels

SET • LOCK KEY [SET] • [ ](SET)

■ Function display (continued)

■ Caution (for the optional BP-265 Li-Ion battery pack)

■ Optional battery case (BP-263) ■ Battery information

■ Regular charging Transceiver

■ Desktop battery chargers

Turn power OFF

■ External DC power operation

■ Setting the squelch level ■ Monitor function

Two segments blink

 he [MONI] key can be set to a ‘sticky’ operation in the

■ Selecting the mode 1

■ Setting the tuning step ■ Setting the frequency

[DIAL] changes the frequency

5 kHz tuning step

D Using the keypad 1

■ Operating mode selection ■ Key lock function

To prevent accidental transmission, the transceiver has a

■ Receiving ■ Transmit power selection 1

D Checking the repeater input signal D Off band indication

Push and hold

■ Auto repeater function

FREQUENCY RANGE SHIFT DIRECTION Korean version

e Push [ ] to return to the frequency display.

■ General description ■ Selecting a call channel

■ Selecting a memory channel 1

■ Memory channel programming

[EXAMPLE]: Programming 145.440 MHz into memory channel 11 (a blank channel).

The VFO mode Enter the select memory write mode.

Return to the VFO mode.

■ Memory bank setting 1

■ Memory bank selection

Bank channel is selected.

Regular memory channel

Bank channel is displayed.

■ Programming memory/bank/scan name 1

■ Programming memory/bank/scan name (continued)

q While continuing to push [SET], turn the power ON to

Push and hold e Push [ ] to return to the frequency display.

Select “m nAmE” or “S nAmE*1”

■ Copying memory/call contents

[DIAL] [EXAMPLE]: Copying memory channel 11 to the VFO mode.

Memory mode Enter Return to the VFO mode.

■ Erasing/transferring bank contents

q Select a desired bank’s contents to be transferred or

Bank channel is displayed.

w Push [S.MW](V/M/C) for 1 sec. to enter the select memory

■ Scan types (continued)

Example: While scaning the 144 MHz band

DUPLEX SCAN (pp. 42, 44)

■ Scan edges programming

he [MONI] key can be set to a ‘sticky’ operation in the

To prevent accidental transmission, the transceiver has a

e Push [ ] to return to the frequency display.

q While continuing to push [SET], turn the power ON to

Push and hold e Push [ ] to return to the frequency display.

q Select a desired bank’s contents to be transferred or

w Push [S.MW](V/M/C) for 1 sec. to enter the select memory

emory bank scan skips any memory channels in the se-

he scan resume timer must be set shorter than the scan

r P ush and hold [SET] for 1 sec., then rotate [DIAL] to

D DTMF TX key (DTMF-T) D Microphone gain (MIC G) 1

D VOX time-out timer (VOXTOT)

D Display type (DISP M) D Auto low power (AUTOLP) 1

• If a digit is mistakenly programmed, push [SET] (or [BAND]) re-

■ Tone frequency and DTCS code 1

D Setting DTCS code for DTCS squelch D Setting DTCS polarity

q S et the desired frequency or memory channel to be

■ Weather channel operation U.S.A. version only 1

OTE: While receiving a signal on a frequency other than

• CP-12L cigarette lighter cable with noise filter • HS-94/HS-95/HS-97 headset

➥ While speaking into the headset microphone, adjust the