ICOM IC-T70A Instruction Manual

INSTRUCTION MANUAL
VHF/UHF DUAL BAND FM TRANSCEIVER
iT70A iT70E
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.
FOREWORD
Thank you for purchasing this ne Icom product. The ICT70A/T70E VHF/UHF DUAL BAND FM TRANSCEIVER is designed and build with Icoms superior technology and craftsmanship. With proper care, this product should provide you with years of trouble-free operation. We want to take a moment of your time to thank you for making your IC-T70A/T70E your radio of choice, and hope you agree with Icoms philosophy of technology rst. Many hours or research and development went into the design of your IC-T70A/T70E.
FEATURES
Dust-protection/Splash-resistant construction (IP54*)
* Only when the battery pack/case, antenna and jack cover are attached.
Built in VOX circuit enabling the VOX operation* (voice operated transmission)
* To use the VOX operation, an optional headset and a plug adapter cable are additionally required.
EXPLICIT DEFINITIONS
WORD R DANGER! R WARNING! CAUTION NOTE DEFINITION Personal death, serious injury or an explosion may occur. Personal injury, fire hazard or electric shock may occur. Equipment damage may occur. Recommended for optimum use. No risk of personal injury, re or electric shock.
7 00 mW* AF power with BTL (bridge-tied load) amplier

*At 10% distortion with a 16 load (internal speaker)
IMPORTANT
READ ALL INSTRUCTIONS carefully and completely
before using the transceiver.
SAVE THIS INSTRUCTION MANUAL This

instruction manual contains important operating instructions for the IC-T70A/T70E.
PRECAUTIONS
R WARNING RF EXPOSURE! This device emits
Radio Frequency (RF) energy. Caution should be observed when operating this device. If you have any questions regarding RF exposure and safety standards please refer to the Federal Communications Commission Ofce of Engineering and Technologys report on Evaluating Compliance with FCC Guidelines for Human Radio Frequency Electromagnetic Fields (OET Bulletin 65)
NEVER connect the transceiver to a power source of more

than 16 V DC. This will ruin the transceiver.
NEVER
connect the transceiver to a power source using reverse polarity. This will ruin the transceiver.
DO NOT
mit.
operate the transceiver near unshielded electrical blasting caps or in an explosive atmosphere.
R WARNING! NEVER hold the transceiver so that

the antenna is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 5 to 10 cm (2 to 4 inches) away from the lips and the transceiver is vertical.
DO NOT push the PTT unless you actually intend to transBE CAREFUL! The transceiver will become hot when operating it continuously for long periods of time.
DO NOT use or place the transceiver in direct sunlight

or in areas with temperatures below 20C (4F) or above +60C (+140F). Place the unit in a secure place to avoid inadvertent use by children.
R WARNING! NEVER operate the transceiver with

an earphone, headphones or other audio accessories at high volume levels. Hearing experts advise against continuous high volume operation. If you experience a ringing in your ears, reduce the volume level or discontinue use.
DO NOT use harsh solvents such as benzine or alcohol to

clean the transceiver, because they can damage the transceivers surfaces.
R WARNING! NEVER operate the transceiver while

driving a vehicle. Safe driving requires your full attention anything less may result in an accident.
ii
PRECAUTIONS
KEEP the transceiver away from heavy rain, and never immerse it in the water. The transceiver meets IP54* requirements for dust-protection and splash resistance. However, once the transceiver has been dropped, dust-protection and splash resistance cannot be guaranteed because of possible damage to the transceivers case or the waterproof seal. * Only when the supplied battery pack (or optional battery pack/case), antenna and jack cover are attached.
FCC INFORMATION
FOR CLASS B UNINTENTIONAL RADIATORS:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. I ncrease the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
NEVER operate or touch the transceiver with wet hands.

This may result in an electric shock or may damage the transceiver. Even when the transceiver power is OFF, a slight current still ows in the circuits. Remove the battery pack or batteries from the transceiver when not using it for a long time. Otherwise, the installed battery pack or batteries will become exhausted, and will need to be recharged or replaced.
CAUTION: Changes or modications to this device, not

expressly approved by Icom Inc., could void your authority to operate this device under FCC regulations. iii
SUPPLIED ACCESSORIES
The following accessories are supplied with the transceiver. q Hand strap 1 w Antenna 1 e Battery pack (BP-264)* 1 r Belt clip* 1 t Battery charger (BC-167SA/SD/SV)* 1
* Not supplied, or the shape is different, depending on the transceiver version.
t
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. Microsoft, Windows and Windows Vista are registered trademarks of Microsoft Corporation in the United States and/or other countries.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
iv
TABLE OF CONTENTS
FOREWORD i EXPLICIT DEFINITIONS i FEATURES i IMPORTANT i PRECAUTIONSiiiii FCC INFORMATION iii SUPPLIED ACCESSORIES iv TABLE OF CONTENTS vvi 1 ACCESSORY ATTACHMENT 12 Hand strap1 Belt clip1 Battery pack2 Antenna2 4 5 6 BASIC OPERATION1623 Power ON16 Setting audio volume16 Setting the squelch level17 Monitor function17 Selecting the mode18 Setting the tuning step19 Setting the frequency19 Operating mode selection21 Key lock function21 Receiving22 Transmit power selection22 Transmitting23 REPEATER AND DUPLEX OPERATIONS2428 Repeater operation24 Duplex operation26 Reverse duplex function26 Auto repeater function27 1750 Hz tone28 MEMORY/CALL CHANNELS2939 General description29 Selecting a call channel29 Selecting a memory channel30 Memory channel programming31 Memory bank setting32 Memory bank selection33 Programming memory/bank/scan name34
2 PANEL DESCRIPTION38 Front, top and side panels3 Function display6 3 BATTERY CHARGING815 Caution (for the supplied BP-264 Ni-MH battery pack)8 Caution (for the optional BP-265 Li-Ion battery pack)9 Optional battery case11 Battery information11 Regular charging12 Desktop battery chargers13 External DC power operation15
TABLE OF CONTENTS
7 Selecting memory/bank name indication35 Display type36 Copying memory/call contents37 Memory clearing38 Erasing/transferring bank contents39 SCAN OPERATION4047 Scan types40 Full/band/programmed scan 42 Scan edges programming43 Memory scan 44 Memory bank scan45 Skip channel/frequency setting46 Scan resume setting47 Tone frequency and DTCS code68 Tone/DTCS squelch70 Tone scan71 Weather channel operation72 Cloning function74 Resetting75
11 TROUBLESHOOTING76 12 SPECIFICATIONS 77 13 OPTIONS7882 VOX function80 Remote control function82 14 CE 8384 INDEX 8588
8 PRIORITY WATCH4850 Priority watch types48 Priority watch operation49 9 SET MODES5164 General 51 Set mode item list52 Initial set mode item list52 Set mode items53 Initial set mode items59
10 OTHER FUNCTIONS6575 Programming a DTMF code sequence65 Transmitting a DTMF code sequence66 Setting DTMF transfer speed67
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
vi
ACCESSORY ATTACHMENT
Belt clip
To attach the belt clip: Slide the belt clip in the direction of the arrow until the belt clip locks in place, and makes a click sound.
Hand strap
To facilitate carrying the transceiver, slide the hand strap through the loop on the top of the rear panel as illustrated at the right.
Handstrap To detach the belt clip: q Remove the battery pack from the transceiver, if it is attached. (p. 2) w Lift the tab up (q), and slide the belt clip in the direction of the arrow (w). w q
ACCESSORY ATTACHMENT
1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

Battery pack
To attach the battery pack: q F it the battery pack in the direction of the arrow (q), then close. w Hook the latch until it makes a click sound (w).
Charge the battery pack before use. (pp. 1214) Battery pack/Battery case
Antenna
Insert the antenna connector into the antenna base and tighten the antenna screw. Jack cover
q w
Latch
To detach the battery pack: Be careful! The latch is tightly locked, so use caution when releasing it. DO NOT use your nger nail. Use the edge of a coin or screwdriver tip to carefully release it. Unhook the latch ( e ), and lift up the battery pack in the direction of the arrow (r).
Battery pack/Battery case
N EVER carry the transceiver by holding only the antenna. W hen the jack is not in use, keep the jack cover in place to protect the connector from dust and moisture.
e Latch
For your information h i r d - p a r t y a n t e n n a s m ay i n c r e a s e t ra n s c e i ve r T p e r fo r m a n c e . A n o p t i o n a l A D - 9 2 S M A A N T E N N A CONNECTOR ADAPTER is available to connect an antenna that has a BNC connector.
PANEL DESCRIPTION
Front, top and side panels

q ANTENNA
CONNECTOR q ANTENNA CONNECTOR (p. 2) Connects to the supplied antenna.
An optional AD-92SMA adapter (p. 79) is available for connecting an antenna with a BNC connector.
w EXTERNAL SPEAKER/
MICROPHONE JACKS
e CONTROL DIAL r VOLUME

CONTROL Speaker
t PTT SWITCH y EXTERNAL

DC IN JACK Internal microphone Function display (pp. 6, 7)
wE XTERNAL SPEAKER/MICROPHONE JACKS [SP/MIC] Connect an optional speaker microphone, cloning cable, or headset, if desired. See page 79 for a list of available options. Be sure to turn power OFF before connecting or dis connecting optional equipment to/from the [SP/MIC] jack. e CONTROL DIAL [DIAL] Rotate to select the operating frequency. (p. 19) During memory mode operation, rotate to select the memory channel. (pp. 18, 30) W hile scanning, changes the scanning direction. (pp. 42, 44, 45) While continuing to push [MONI] (BAND), sets the squelch level. (p. 17) After pushing [BAND] during memory mode operation, selects the programmed bank. (p. 33) During set mode operation, rotate to select the set items. (p. 51)
Keypad (pp. 4, 5)
PANEL DESCRIPTION D Keypad

r VOLUME CONTROL [VOL] Adjust the audio volume level. (p. 16) During set mode operation, rotate to select the options. (p. 51) t PTT SWITCH [PTT] Push and hold to transmit, release to receive. (p. 23)
2
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

For IC-T70E only Push briey, then push and hold to transmit a 1750 Hz tone burst. (p. 28)
y EXTERNAL DC IN JACK [DC IN] Connects the supplied wall charger, BC-167S, to charge the attached battery pack, BP-264. (p. 12)
The transceiver can charge only the BP-264 Ni-MH battery pack. Charging the BP-265 Li-Ion battery pack requires the BC-193 desktop charger.
Push to input numbers for frequency input or memory channel selection. While continuing to push [PTT], push the key to send the DTMF code. (pp. 66, 67)
[ 0][9] send 09, [A](SET) sends A, [B](BAND) sends B, [C](H/M/L) sends C, [D](V/M/C) sends D, [M](DUP) sends M (E) and [#](T.SCAN) sends # (F).
Connect an external DC power supply through the optional CP-12L, CP-19R or OPC-254L for external DC operation. (p. 15)
POWER KEY [ ] Push and hold for 1 sec. to turn the transceiver power ON or OFF. (p. 16) VFO/MEMORY/CALL SELECT MEMORY WRITE KEY [V/M/C] [S.MW](V/M/C) Push to select the VFO mode, memory mode, call channel mode or weather channel mode*. (pp. 18, 29, 30, 72)
* Only for the U.S.A. version transceiver.
Push and hold for 1 sec. to enter select memory write mode. (p. 31)
PANEL DESCRIPTION
D Keypad (continued) OUTPUT POWER SCAN KEY [H/M/L] [SCAN](H/M/L) Push to select the output power. (p. 22)
Selects the transmit output power from high, middle or low.
TONE SCAN KEY [T.SCAN](#) Push and hold for 1 sec. to start the tone scan function. (p. 71) TONE/TONE SQUELCH KEY [TONE](0) Push and hold for 1 sec. to select sequentially repeater tone, tone squelch, tone squelch reverse, DTCS squelch, DTCS squelch reverse and no tone operation. (p. 70)
The pocket beep function is available with tone squelch and DTCS squelch. (p. 70)
Push and hold for 1 sec. to enter the scan type selection mode. (pp. 42, 44, 45)
Push again to start the scan.
BAND MONITOR KEY [BAND] [MONI](BAND) During VFO mode operation, push to select an operating frequency band. (p. 19) Push and hold to open the squelch temporarily and monitor the operating frequency. (p. 17) While continuing to push this key, rotate [DIAL] to adjust the squelch level. (p. 17) During memory mode operation, push to enter the memory bank group selection. (p. 33) SET LOCK KEY [SET] [ ](SET) Push to enter the Set mode. (p. 51) Push and hold for 1 sec. to toggle the lock function ON or OFF. (p. 21) During select memory write mode, push to select the items. (pp. 32, 34, 38, 39)
DUPLEX KEY [DUP](M) Push and hold for 1 sec. to select minus duplex, plus duplex or simplex operation. (p. 26)
DUP (minus duplex), DUP (plus duplex) and no indication (simplex) appear in order.
PANEL DESCRIPTION
2
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

Function display
q w e r ty
w DUPLEX ICON (p. 26) DUP appears when plus duplex is selected, DUP appears when minus duplex is selected. e TONE ICON T appears while the subaudible tone encoder is in use. (p. 24) T SQL appears while the tone squelch function is in use. (p. 70) T SQL-R appears while the reverse tone squelch function is in use. (p. 70) DTCS appears while the DTCS squelch function is in use. (p. 70) DTCS -R appears while the reverse DTCS squelch function is in use. (p. 70) S appears with the T SQL or DTCS indicator while the pocket beep function (with CTCSS or DTCS) is in use. (p. 70) r VOX ICON (p. 80) Appears when the VOX function is in use. t AUTO POWER OFF ICON (p. 59) Appears when the Auto Power OFF function is ON. y KEY LOCK ICON (p. 21) Appears when the key lock function is activated.
q BATTERY ICON (pp. 11, 12) m When the BP-264 or BP-265 is attached (battery icons) appear when the battery pack has ample capacity. appears when the battery pack has less than half capacity. blinks before the battery pack is exhausted. The battery pack must be charged. The icons show , and (disappears) in sequence while charging the BP-264 Ni-MH battery pack.
m When the BP-263 is attached

(battery icons) appear when the batteries have ample capacity. blinks before the batteries are exhausted. The batteries must be replaced.
PANEL DESCRIPTION
Function display (continued)
!6 !5
u i o
!1 WEATHER CHANNEL ICON (pp. 7273) Appears when the weather alert function is in use. !2 S/RF METER Shows the relative signal strength while receiving signals. (p. 22) Shows the output power level while transmitting. (pp. 22, 23) !3 OPERATING MODE ICONS (p. 21) Shows the selected operating mode.
FM and FMN are selectable.
!4
!3
!2
!1 !0
u SKIP ICONS appears when the selected memory channel is set as a skip channel. (p. 46) P appears when the displayed frequency is set as a skip frequency in memory mode. (p. 46) i MEMORY ICON (pp. 18, 30) Appears when memory mode is selected. o MEMORY CHANNEL NUMBER S hows the selected memory channel number. (pp. 18, 30) C0 or C1 appears when the call channel is selected. (pp. 18, 29) !0 PRIORITY WATCH ICON (pp. 49, 50) Appears when priority watch is in use.
!4 POWER ICONS (p. 22) L appears when low power is selected. M appears when middle power is selected. No indicator appears when high power is selected. !5 FREQUENCY READOUT Displays a variety of information, such as operating frequency, set mode contents.
The decimal point blinks during scan.
D uring memory mode operation, the programmed memory or memory bank name is displayed. !6 TRANSMIT ICON (p. 23) Appears during transmit.
BATTERY CHARGING
Caution (for the supplied BP-264 Ni-MH battery pack)
R DANGER! NEVER short terminals (or charging terminals) of the battery pack. Also, current may ow into nearby metal objects such as a necklace, so be careful when placing battery packs (or the transceiver) in handbags, etc. Simply carrying with or placing near metal objects such as a necklace, etc. may cause shorting. This may damage not only the battery pack, but also the transceiver. R DANGER! NEVER incinerate used battery packs. Internal battery gas may cause an explosion. R DANGER! NEVER immerse the battery pack in water. If the battery pack becomes wet, be sure to wipe it dry BEFORE attaching it to the transceiver. C AUTION: Always use the battery within the specied temperature range, 5C to +60C (+23F to +140F). Using the battery out of its specified temperature range will reduce the batterys performance and battery life. C AUTION: Shorter battery life could occur if the battery is left completely discharged, or in an excessive temperature environment (above +55C; +131F) for an extended period of time. If the battery must be left unused for a long time, it must be detached from the radio after charging. Keep it safely in a cool dry place at the following temperature range: 20C to +45C (4F to +113F) (up to a month) 20C to +35C (4F to +95F) (up to six months) 20C to +25C (4F to +77F) (up to a year*)
* We recommend charging the battery pack every 6 months.
3
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

C lean the battery terminals to avoid rust or misscontact. Keep battery terminals clean. Its a good idea to clean battery terminals once a week. I f your Ni-MH battery pack seems to have no capacity, even after being charged, completely discharge it by leaving the power ON overnight. Then, fully charge the battery pack again. If the battery pack still does not retain a charge (or only very little charge), a new battery pack must be purchased. Prior to using the transceiver for the rst time, the battery pack must be fully charged for optimum life and operation. Recommended temperature range for charging: between 0C and +45C for the regular charge by the transceiver. or between +10C and +40C for the rapid charge with the BP-191. Use the supplied charger (BC-167S) or optional charger (BC-191) only. NEVER use other manufacturers chargers. The battery pack contains a rechargeable battery. Charge the battery pack before first operating the transceiver, or when the battery pack becomes exhausted. If you want to prolong the battery life, the following points should be observed: - Avoid over charging. - Use the battery pack until it becomes almost completely exhausted, under normal conditions. We recommend battery charging after transmitting becomes impossible.
BATTERY CHARGING
Caution (for the optional BP-265 Li-Ion battery pack)

Misuse of Lithium-Ion batteries may result in the following hazards: smoke, re, or the battery may rupture. Misuse can also cause damage to the battery or degradation of battery performance. R DANGER! Use and charge only specied Icom battery packs with Icom radios and Icom chargers. Only Icom battery packs are tested and approved for use with Icom radios or charged with Icom chargers. Using third-party or counterfeit battery packs may cause smoke, re, or cause the battery to burst. R DANGER! DO NOT expose the battery to rain, snow, seawater, or any other liquids. Do not charge or use a wet battery. If the battery gets wet, be sure to wipe it dry before using. R DANGER! NEVER incinerate a used battery pack, since internal battery gas may cause it to rupture, or may cause an explosion. R DANGER! NEVER solder the battery terminals, or NEVER modify the battery pack. This may cause heat generation, and the battery may burst, emit smoke or catch re. R DANGER! Use the battery only with the transceiver for which it is specied. Never use a battery with any other equipment, or for any purpose that is not specied in this instruction manual. R DANGER! If uid from inside the battery gets in your eyes, blindness can result. Rinse your eyes with clean water, without rubbing them, and see a doctor immediately. R WARNING! Immediately stop using the battery if it emits an abnormal odor, heats up, or is discolored or deformed. If any of these conditions occur, contact your Icom dealer or distributor. R WARNING! Immediately wash, using clean water, any part of the body that comes into contact with uid from inside the battery.
D Battery caution
R DANGER! DO NOT hammer or otherwise impact the battery. Do not use the battery if it has been severely impacted or dropped, or if the battery has been subjected to heavy pressure. Battery damage may not be visible on the outside of the case. Even if the surface of the battery does not show cracks or any other damage, the cells inside the battery may rupture or catch re. R DANGER! NEVER use or leave battery pack in areas with temperatures above +60C (+140F). High temperature buildup in the battery, such as could occur near res or stoves, inside a sun heated car, or in direct sunlight may cause the battery to rupture or catch re. Excessive temperatures may also degrade battery performance or shorten battery life.
BATTERY CHARGING
3
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
10
R WARNING! NEVER put the battery in a microwave oven, high-pressure container, or in an induction heating cooker. This could cause a re, overheating, or cause the battery to rupture. CAUTION: Always use the battery within the specied temperature range, 20C to +60C (4F to +140F). Using the battery out of its specied temperature range will reduce the batterys performance and battery life. CAUTION: Shorter battery life could occur if the battery is left fully charged, completely discharged, or in an excessive temperature environment (above +50C; +122F) for an extended period of time. If the battery must be left unused for a long time, it must be detached from the radio after discharging. You may use the battery until the remaining capacity is about half, and then keep it safely in a cool dry place at the following temperature range: 20C to +50C (4F to +122F) (up to a month) 20C to +35C (4F to +95F) (up to three months) 20C to +20C (4F to +68F) (up to a year)
D Charging caution
R DANGER! NEVER charge the battery pack in areas with extremely high temperatures, such as near res or stoves, inside a sun-heated vehicle, or in direct sunlight. In such environments, the safety/protection circuit in the battery will activate, causing the battery to stop charging. R WARNING! DO NOT charge or leave the battery in the battery charger beyond the specied time for charging. If the battery is not completely charged by the specied time, stop charging and remove the battery from the battery charger. Continuing to charge the battery beyond the specied time limit may cause a re, overheating, or the battery may rupture. R WARNING! NEVER insert the transceiver (battery attached to the transceiver) into the charger if it is wet or soiled. This could corrode the battery charger terminals or damage the charger. The charger is not waterproof. CAUTION: DO NOT charge the battery outside of the specied temperature range: BC-193 (+10C to +40C; +50F to +104F). Icom recommends charging the battery at +20C (+68F). The battery may heat up or rupture if charged out of the specied temperature range. Additionally, battery performance or battery life may be reduced.
BATTERY CHARGING
Optional battery case (BP-263)

When you would like to use the optional battery case (BP-263), install 6 AA (LR6) size alkaline batteries, as shown below. q Remove the battery case if it is attached. (p. 2) w Install 6 AA (LR6) size alkaline batteries.
Install only alkaline batteries. Be sure to observe the correct polarity. Be careful! The negative terminals of the battery case protrude from the body, so pay attention not to injure your fingers when inserting the batteries.
Battery information
D Battery life
Battery pack Voltage BP-263 BP-264 BP-265 Capacity Battery life*1 *2 VHF UHF VHF UHF 11.5 hrs. 10 hrs. 16 hrs. 13.5 hrs. Battery case for AA (LR6) 6 alkaline 7.2 V 7.4 V 1400 mAh (typ.) 1900 mAh (min.) 2000 mAh (typ.)
e Attach the battery case. (p. 2) CAUTION: W hen installing batteries, make sure they are all the same brand, type and capacity. Also, do not mix new and old batteries together. Never use batteries whose insulated covering is damaged. Never incinerate used battery cells since internal battery gas may cause them to rupture. N ever expose a detached battery case to water. If the battery case gets wet, be sure to wipe it dry before using it. Keep battery contacts clean. Its a good idea to clean battery terminals once a week. 11
*1 When the power save function is set to Auto, and the operating time is calculated under the following conditions; TX : RX : standby = 5 : 5 : 90 *2 The average operating time depends on the alkaline cells used.
ven when the transceiver power is OFF, a small current E still flows in the radio. Remove the battery pack or case from the transceiver when not using it for a long time. Otherwise, the battery pack or installed batteries will become exhausted.
Indication Battery condition The battery pack (BP-264/BP-265) or battery case (BP-263) has ample capacity. The battery pack (BP-264/BP-265) is nearing exhaustion. (blinks) The battery pack or battery case is exhausted. Charging the BP-264/BP-265 or replacing the batteries in the BP-263 is necessary.
BATTERY CHARGING
Regular charging
Prior to using the transceiver for the first time, the battery pack must be fully charged for optimum life and operation.
Transceiver
BC-167S to AC outlet CP-12L (Optional) to [DC IN] to cigarette lighter socket (12 V DC) CP-19R (Optional)
The shape may diffe depending on the version.
D Battery icons
While charging, the icons show , and (disappears) in sequence, and CHARGE appears when the transceivers power is OFF. The icons and CHARGE disappear when the battery pack is completely charged.
D Charging note
Be sure to turn the transceiver power OFF. Otherwise the battery pack will not be charged completely, or will take much longer to charge. The transceiver can charge only the BP-264 battery pack. Other types of rechargeable battery, such as Ni-Cd or Li-Ion cannot be charged. External DC power operation becomes possible when using an optional CP-12L, CP-19R or OPC-254L. The attached battery pack is also charged simultaneously, except during transmit (see p. 15 for more details). The external DC power supply voltage must be between 1016 V to charge the battery pack and for operation when using an optional OPC-254L. We recommend 11 V DC for operation. If the battery icons ( and ) disappear only 1 min. after connecting to the DC power supply, the battery pack may have problem. In this case, contact your Icom dealer/ distributor, or purchase a new battery pack.
BP-264 Turn power OFF while charging the battery pack. Charging time period: Approx. 8 hours
OPC-254L (Optional) to 11 V DC (power supply) Black: _ White: +
Be sure to disconnect the AC adapter from the AC outlet after the charging is completed. Otherwise the transceiver may receive switching noise from the AC adapter, depending on the operating frequencies and/or antenna used. 12
BATTERY CHARGING
Desktop battery chargers

D Charging note
Be sure to turn the transceiver power OFF. N EVER place the transceiver with the battery pack to the desktop charger when the transceiver is connected to the DC power supply. This may cause the chargers malfunction and the charging indicator of the charger lights red*. In that case, disconnect the AC adapter from the charger, and then reconnect the AC adapter to the charger.
*Red indicator is only available for the BC-191 or BC-193.
D Rapid charging with the BC-191

The BC-191 provides rapid charging of only the BP-264 Ni-MH battery pack. Never use it to charge any other battery pack. Charging time (with the BC-123S): Approx. 2 hours The following item is additionally required:
The AC adapter BC-123S (not supplied with some versions) or the OPC-515L or CP-23L DC power cable.
Battery pack BC-123S Transceiver
The optional CP-23L* and OPC-515L can be used instead of the supplied AC adapter. Connect one of these to the [DC 12-16V] jack.
* CP-23L can only be used with the BC-191 or BC-193.
IMPORTANT: Ensure the tabs on the battery pack are correctly aligned with the guide rails inside the charger.
Tabs
Turn power OFF

Screws* (Self tapping screw: M3.5 at least 30 mm) *Purchase separately. Using screws is recommended to secure the charger. Charge indicator Lights orange : While charging Lights green : Charging is completed Blinks red : Charging error has occured
Guide rail
CAUTION: When using the OPC-515L DC power cable NEVER connect the OPC-515L to a power source using reverse polarity. This will ruin the battery charger. White line: + 13 Black line:
The optional OPC515L (for a DC power source) or CP-23L (for a 12 V cigarette lighter socket) can be used instead of the AC adapter.
BATTERY CHARGING D Regular chrging with the BC-192

The BC-192 provides regular charging of only the BP-264 Ni-MH battery pack. Never use it to charge any other battery pack. Charging time (with the BC-147S): Approx. 16 hours The following item is additionally required:
The AC adapter BC-147S (not supplied with some versions) or the OPC-515L DC power cable.
BC-147S Battery pack Transceiver BC-123S
D Rapid charging with the BC-193

The BC-193 provides rapid charging of only the BP-265 LiIon battery pack. Never use it to charge any other battery pack. Charging time: Approx. 2.5 hours The following item is additionally required:
The AC adapter BC-167S (not supplied with some versions) or the OPC-515L or CP-23L DC power cable.
Battery pack Transceiver
Turn power OFF

Screws* (Self tapping screw: M3.5 at least 30 mm) *Purchase separately. Using screws is recommended to secure the charger.
Turn power OFF
The optional OPC-515L (for a DC power source) can be Charge indicator used instead of Charging time period differs Lights green while charging. the AC adapter. depending on the input voltage. NOTE: 12 V : Approx. 36 hours The charger indicator will 13.8 V : Approx. 21 hours not go out even after a 16 V : Approx. 16 hours battery pack is fully charged.
The optional OPC515L (for a DC power source) can be used instead of the AC adapter.
Screws* (Self tapping screw: M3.5 at least 30 mm) *Purchase separately. Using screws is recommended to secure the charger. Charge indicator Lights orange : While charging Lights green : Charging is completed Blinks red : Charging error has occured
14
BATTERY CHARGING
External DC power operation

An optional cigarette lighter cable (CP-12L or CP-19R; for 12 V cigarette lighter socket) or external DC power cable (OPC-254L) can be used for external power operation. (We recommend the CP-19R when you want to connect a 12 V cigarette lighter socket.)
Transceiver CP-12L (Optional)
D Operating note
Power supply voltage must be between 10.016.0 V DC. (We recommend 11.0 V DC.) NEVER CONNECT OVER 16 V DC directly into the [DC IN] jack of the transceiver. B E SURE to use a CP-12L, CP-19R or OPC-254L when connecting to a regulated 12 V DC power supply. Use an external DC-DC converter to connect the transceiver through a CP-12L, CP-19R or OPC-254L to a 24 V DC power source. The voltage of the external power supply must be within 1016 V DC when using either CP-12L, CP-19R or OPC254L, otherwise, use the battery pack/battery case. D isconnect the power cable from the transceiver when not using it. Otherwise, the vehicle battery will become exhausted. The power save function is automatically deactivated during external DC power operation.
to [DC IN]
to cigarette lighter socket (12 V DC) CP-19R (Optional)
OPC-254L (Optional) BP-264 to 11 V DC (power supply) Black: _ White: +
NOTE: Up to 5 W (approx.) of maximum output power is available when using an external DC power. However, when the supplied voltage exceeds 14 V, the built-in protection circuit activates to reduce the transmit output power to 2.5 W (approx.).
15
BASIC OPERATION
Power ON
Push and hold [ ] for 1 sec. to turn power ON.
Push and hold [ ] for 1 sec. to turn power OFF.
4
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
16
Setting audio volume

Rotate [VOL] to adjust the audio level.
If squelch is closed, push and hold [MONI](BAND) while setting the audio level. The display shows the volume level while setting. [VOL]
Volume level
The voltage indication can be skipped in the Initial set mode (p. 61).
Minimum setting (no audio)
Maximum setting
The beep level is adjusted in the Initial set mode (p. 60).
BASIC OPERATION
Setting the squelch level

The squelch circuit mutes the received audio signal, depending on the signal strength. The transceiver has 9 squelch levels, a continuously open setting and an automatic setting. While continuing to push [MONI](BAND), rotate [DIAL] to select the squelch level.
LEVEL1 is loose squelch (for weak signals) and LEVEL9 is tight squelch (for strong signals). Auto indicates the automatic level adjustment by a noise pulse counting system. OPEn indicates the continuously open setting. [DIAL]
Monitor function
This function is used to listen to weak signals without disturbing the squelch setting; or to open the squelch manually even when mute functions such as the tone squelch are in use. Push and hold [MONI](BAND) to monitor the operating frequency.
The 1st and 2nd segments of the S-meter blink.
Two segments blink
Automatic squelch
he [MONI] key can be set to a sticky operation in the T Initial set mode. See page 63 for details.
Maximum level
17
BASIC OPERATION
4
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
18
Selecting the mode

q Push [V/M/C] repeatedly to sequentially select the VFO mode, memory mode, call channel mode or weather channel mode*. * Only for the U.S.A. version transceiver. w R otate [DIAL] to change the frequency or select a desired channel.
[DIAL]
D Memory mode
Memory mode is used for operation on memory channels which store programmed frequencies.
Memory mode display
D VFO mode
The VFO mode is used to set the desired frequency.
VFO mode display
appears when memory mode is selected. Appears Only programmed memory channels can be selected. Enter the channel number directly to select the desired memory channel. (p. 30)
D Call channel mode

Select a call channel to operate on one of your two most oftenused frequencies.
Call channel display
What is VFO? VFO is an abbreviation of Variable Frequency Oscillator. Frequencies for both transmitting and receiving are generated and controlled by the VFO.
C0 or C1 appears instead of the memory channel number when the Call channel mode is selected.
D Weather channel mode*

There are 10 weather channels for monitoring weather broadcasts from NOAA (National Oceanic and Atmospheric Administration).
* Only for the U.S.A. version transceiver. Weather channel display
BASIC OPERATION
Setting the tuning step

The tuning step can be selected for both band. The following tuning steps are available for the IC-T70A/T70E. 5.0 kHz 10.0 kHz 12.5 kHz 15.0 kHz 20.0 kHz 25.0 kHz 30.0 kHz 50.0 kHz 100.0 kHz 125.0 kHz 200.0 kHz
Setting the frequency

D Using the dial
q Push [V/M/C] to select the VFO mode, if any other mode is selected. w Push [BAND] to select the desired frequency band. e Rotate [DIAL] to select the desired frequency.
The frequency changes according to the preset tuning steps. See the previous topic to set the tuning step. [DIAL] 144 MHz band
D Tuning step selection
q In the VFO mode, push [BAND] to select the desired frequency band.
If you are in another mode, such as a memory channel/call channel mode or the weather channel mode, push [V/M/C] to select the VFO mode rst, then push [BAND] to select the desired band.
Push [BAND] 440 MHz band
w Push [SET] to enter the Set mode. e Rotate [DIAL] to select the tuning step set item, then rotate [VOL] to select the desired tuning step. r Push [V/M/C] to return to the VFO mode.
[DIAL] [VOL]
[DIAL] changes the frequency according to the selected tuning step. 5 kHz tuning step
19
BASIC OPERATION D Using the keypad

The frequency can be directly set using the numeric keys.
If a frequency outside the transceivers frequency range is entered, the previously displayed frequency is automatically recalled after entering the last digit.
4
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
20
q Push [V/M/C] to select the VFO mode, if any other mode is selected. w Enter the desired frequency with the keypad. Entering 145.500 MHz
Depending on the tuning step setting, it may not be possible to input a 1 kHz digit. In this case, enter 0 as a 1 kHz digit, then rotate [DIAL] to set the desired frequency.
Changing 10 MHz and below Editing 445.560 MHz to 432.380 MHz
Changing 1 MHz and below
Editing 145.500 MHz to 144.640 MHz
Changing 100 kHz and below Editing 145.500 MHz to 145.640 MHz Push to cancel numeral key input.
BASIC OPERATION
Operating mode selection

Operating modes are determined by the modulation of the radio signals. The transceiver has two operating modes, FM and FM-N (narrow). The mode selection is stored independently for each band and memory channel. q Push [V/M/C] to select the VFO mode, if any other mode is selected. w Push [BAND] to select the desired frequency band. e Push [SET] to enter the Set mode. r Rotate [DIAL] to select the operating mode set item, then rotate [VOL] to select WIdE (FM) or nARROW (FM-narrow). t Push [V/M/C] to return to the VFO mode.
[DIAL] [VOL]
Key lock function

To prevent accidental frequency changes and unnecessary function access, use the lock function. Push and hold [ tion ON or OFF. ](SET) for 1 sec. to turn the lock func-
appears while the lock function is activated. [ ], [ ](SET), [MONI](BAND), [PTT], [VOL] and squelch adjustment ([MONI](BAND) + [DIAL]) are operable while the lock function is activated.
Appears
FM
FMN
To prevent accidental transmission, the transceiver has a PTT lock function. Turns the PTT lock function ON or OFF in the Initial set mode. (p. 62)
: Rotate [VOL]
21
BASIC OPERATION
4
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
22
Receiving
Make sure a charged battery pack (BP-264, BP-265) or a case with brand new alkaline batteries (BP-263) is attached to the transceiver (pp. 2, 1214). q Push and hold [ ] for 1 sec. to turn power ON. w Rotate [VOL] to set the desired audio level. (p. 16)
The frequency display shows the volume level while setting.
Transmit power selection

The transceiver has three output power levels to suit your operating requirements. Low output power during short-range communications may reduce the possibility of interference to other stations, and will conserve battery power. Push [H/M/L] to toggle the transmit output power between High (5 W*), Middle (2.5 W*) and Low (0.5 W*). *Approximately
e Set the receive frequency. (p. 20) r Set the squelch level. (p. 17)
While continuing to push [MONI](BAND), rotate [DIAL]. The rst click of [DIAL] indicates the current squelch level. LEVEL1 is loose squelch (for weak signals) and LEVEL9 is tight squelch (for strong signals). Auto indicates the automatic level adjustment by a noise pulse counting system. Push and hold [MONI](BAND) to open the squelch manually.
Appears
While transmitting
t When a signal is received:

Squelch opens and audio is heard. The S/RF meter shows the relative signal strength level. r Set squelch level e Set frequency w Set audio level r Push and hold for setting the squelch (Push and hold to monitor) e Select band
Low power transmission
Middle power transmission
q Power ON
High power transmission
BASIC OPERATION
Transmitting
CAUTION: T ransmitting without an antenna will damage the transceiver. NOTE: To prevent interference, push and hold [MONI] (BAND) to listen on the frequency before transmitting. q Set the operating frequency. (p. 20)
You can transmit on the 144 MHz/440 MHz amateur bands only. Select the desired output power. See the previous page for details.
R WARNING! NEVER transmit for long periods of time. When the transceiver is used for prolonged transmissions at high power or middle power, the transceiver radiates heat to protect itself from overheating. The transceivers chassis will become hot and may cause a burn.
To prevent the transceivers overheating, the default setting of the time-out timer function is set to 5 minutes (p. 62). Be careful when the time-out timer function is turned OFF or set to a long time period, and transmission is made for long periods.
w Push and hold [PTT] to transmit.

appears. T he S/RF meter shows the output power level.
[PTT]
DO NOT operate the transceiver in a situation that will obstruct heat dissipation, especially if the transceiver is operated with an external power supply. Heat dissipation may be affected, and it may cause a burn, warp the casing or damage the transceiver.
Microphone
e Speak into the microphone using your normal voice level.

DO NOT hold the transceiver too close to your mouth or speak too loudly. This may distort your speech.
Appears
NOTE: When the transceiver becomes hot from continuous transmission, etc., the transceivers heat protection function gradually reduces the output power to 2.5 W (Mid), then it stops transmission after that. This is done to protect the transceiver itself until it has cooled down.
M (Power icon) blinks while the heat protection function reduces the output power. Hot is displayed while the heat protection function inhibits transmission.
r Release [PTT] to return to receive.
While using the battery case: Frequent or continuous transmissions can cause the batteries to overheat. To prevent this, we recommend using the middle or low power settings. 23
REPEATER AND DUPLEX OPERATIONS

Repeater operation
When using a repeater, the transmit frequency is shifted from the receive frequency by the frequency offset (p. 54). This is called duplex operation. It is convenient to program repeater information into memory channels (p. 29).
Repeater
144.700 MHz 144.700 MHz Uplink (transmit frequency) Downlink (receive frequency)
5
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
24
Appears
e Push and hold [TONE](0) for 1 sec. to activate the subaudible tone encoder, according to the repeater requirements.
T appears. Refer to p. 53 for tone frequency settings.
r Push and hold [PTT] to transmit.

T he displayed frequency automatically changes to the transmit frequency (repeater input frequency). If OFF appears, check the frequency offset or shift direction. (p. 26) While receiving
[PTT]
145.300 MHz
145.300 MHz
Station A
Station B
q Set the receive frequency (repeater output frequency). w Set the shift direction of the transmit frequency. (DUP or
DUP; see p. 26 for details.) When the auto repeater function is in use (U.S.A. and Korean versions only), this selection and step e are not necessary. (p. 27) DUPor DUP appears
While transmitting
t Release [PTT] to receive. y Push and hold [MONI](BAND) to check whether the other stations transmit signal can be directly received or not. U.S.A. and Korean versions: he auto repeater function uses standard values of the T repeater tone frequency and frequency offset.
D Checking the repeater input signal

The transceiver can check whether the other stations transmit signal can be received directly or not, by listening on the repeater input frequency. Push and hold [MONI](BAND) to check whether the other stations transmit signal can be received directly or not.
When the other stations signal can be directly received, move to a non-repeater frequency to use simplex. (duplex OFF) Display while receiving
D Off band indication

If the transmit frequency is out of the amateur band when [PTT] is pushed, the off band indication, OFF, appears on the display. Check the frequency offset or duplex direction in that case. (p. 26)
U.S.A. and Korean versions: he auto repeater function uses standard values of the T frequency offset.
Push and hold Receives 0.6 MHz lower
CONVENIENT! Tone scan function: When you dont know the subaudible tone used for a repeater, the tone scan is convenient for detecting the tone frequency. Push and hold [T.SCAN](#) for 1 sec. to start the tone scan. See p. 71 for more information.
Blinks while pushing and holding [MONI]
25
5
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
26
Duplex operation
D Setting frequency offset
q Push [SET] to enter the Set mode. w Rotate [DIAL] to select the frequency offset set item, then rotate [VOL] to set the frequency offset. e Push [V/M/C] to return to the frequency display.
[DIAL] [VOL]
U.S.A. and Korean versions: The auto repeater function has priority over the manual duplex setting. If the transmit frequency changes after setting, the auto repeater function may have changed the duplex setting. Turn the auto repeater function OFF to prevent this (p. 27).
Reverse duplex function

When the reverse duplex function is ON, the receive and transmit frequencies are reversed. The function can be set in the Set mode. q Push [SET] to enter the Set mode. w Rotate [DIAL] to select the reverse duplex set item, then rotate [VOL] to turn the function ON or OFF.
Frequency offset setting
0.6 MHz offset
D Setting duplex direction

Push and hold [DUP](M) for 1 sec. to select DUP (negative offset) or DUP (positive offset).
DUP or DUP indicates the transmit frequency for minus shift or plus shift, respectively. While continuing to push [DUP](M), rotate [DIAL] also selects a duplex setting. When the frequency offset is 0.6 MHz [DIAL] Duplex example
Reverse duplex setting
e Push [V/M/C] to return to the frequency display. Each receive and transmit frequency is shown in the table below, with the following congurations;
Input freq.: 145.300 MHz, Direction: (down), Offset: 0.6 MHz Reversed OFF ON DUP or DUP blinks when the reverse duplex 145.300 MHz 144.700 MHz function is ON. 144.700 MHz 145.300 MHz RX freq. TX freq.
Receiving
Transmitting
+Duplex example
Auto repeater function

The U.S.A. and Korean versions automatically use standard repeater settings (duplex ON/OFF, duplex direction, tone encoder ON/OFF) when the operating frequency falls within or outside of the general repeater output frequency range. The offset and repeater tone frequencies are not changed by the auto repeater function. Reset these frequencies, if necessary. q While continuing to push [SET], turn the power ON to enter the Initial set mode. w Rotate [DIAL] to select the auto repeater set item, then rotate [VOL] to set the auto repeater setting. U.S.A. version:
R1 : Activates duplex only. (default) R2 : Activates duplex and tone. OFF : Auto repeater function is turned OFF.
D Frequency range and offset direction

U.S.A. version FREQUENCY RANGE 145.200145.495 MHz 146.610146.995 MHz 147.000147.395 MHz 442.000444.995 MHz 447.000449.995 MHz Korean version SHIFT DIRECTION DUP appears DUP appears DUP appears DUP appears
Korean version:
On : Activates duplex and tone. (default) OFF : Auto repeater function is turned OFF. Auto repeater setting [DIAL] [VOL]
U.S.A. version
FREQUENCY RANGE 439.000440.000 MHz
SHIFT DIRECTION DUP appears
Korean version
e Push [ ] to return to the frequency display. 27
5
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
28
1750 Hz tone
To access some European repeaters, the transceiver must transmit a 1750 Hz tone burst. For such repeaters, perform the following.
This tone can be use as a Call signal in countries out of Europe.
r Set the receive frequency (repeater output frequency). t Set the shift direction of the transmit frequency. (DUP or
+DUP; see p. 26 for details.)
q Push [SET] to enter the Set mode. w Rotate [DIAL] to select the DTMF key item, then rotate [VOL] to set to t-CALL.
DTMF key setting [DIAL] [VOL]
y While continuing to push [PTT], push [MONI](BAND) to transmit a 1750 Hz tone burst signal.
If OFF appears, check the frequency offset or shift direction. (p. 26) The displayed frequency automatically changes to the transmit frequency (repeater input frequency).
u Push and hold [PTT] to transmit. i Release [PTT] to receive. o Push and hold [MONI](BAND) to check whether the other stations transmit signal can be received directly or not, by listening on the repeater input frequency. CONVENIENT! (For the IC-T70E only) q Set the receive frequency (repeater output frequency). w Set the shift direction of the transmit frequency. (DUP or
+DUP; see p. 26 for details.)
e Push [PTT] briey, then push and hold [PTT] again for 1 to 2 sec. to transmit a 1750 Hz tone burst signal.
Tone call setting If OFF appears, check the frequency offset or shift direction. (p. 26) The displayed frequency automatically changes to the transmit frequency (repeater input frequency).
e Push [V/M/C] to return to the frequency display.
r Push and hold [PTT] to transmit; release to receive.
MEMORY/CALL CHANNELS
Selecting a call channel
q Push [V/M/C] to select the call channel mode.
Pushing [V/M/C] toggles between the VFO mode, the memory channel mode, call channel mode and weather channel mode*. * Only the U.S.A. version transceiver.
General description
The IC-T70A/T70E has 300 memory channels, and 2 call channels. Memory channels include 50 scan edge memory channels (25 pairs) to store often-used frequencies. Also, 26 memory banks, A to Z, are available in each band for storing groups of frequencies, etc. Up to 100 channels can be assigned to a bank.
w Rotate [DIAL] to select a desired call channel.

C0 and C1 are selectable. [DIAL] VHF band call channel
D Memory channel contents

The following information can be programmed into memory channels: Operating frequency (p. 20) Operating mode (p. 21) Duplex direction (+DUP or DUP) with a frequency offset
(p. 26)
UHF band call channel
Reverse duplex function ON/OFF (p. 26) Subaudible tone encoder (p. 24), tone squelch or DTCS squelch ON/OFF (p. 70) Subaudible tone frequency (p. 53), tone squelch frequency or DTCS code with polarity (p. 53) Scan skip setting (p. 46) Memory bank (p. 32) Memory name (p. 34) Tuning step (p. 19) Output power (p. 22) NOTE: Memory data can be erased by static electricity, electric transients, etc. In addition, it can be erased by malfunction and during repairs. Therefore, we recommend that memory data be written down or be saved to a PC using the CS-T70 CLONING SOFTWARE. 29
6
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
30
Selecting a memory channel

D Using [DIAL]
q Push [V/M/C] to select the memory mode.
D Using the Numeral keys

q Push [V/M/C] to select the memory mode.
w Rotate [DIAL] to select a desired memory channel.

Only programmed channels are displayed. [DIAL] Appears
w Use the number keys to enter 3 digits to select a desired memory channel.
The blank channels are also selectable.
Example selecting memory channel 25 Push [V/M/C], then push [0], [2], [5].
Appears Rotate [DIAL] to select the memory channel. The entered memory channel is selected.
Numeral keys
Memory channel programming

q Push [V/M/C] to select the VFO mode. w Set a desired frequency: Push [BAND] to select a desired band. Rotate [DIAL] to set a desired frequency. Push the keypad keys directly to set a desired frequency. In this case, setting the band and frequency using [BAND] and [DIAL] are not required. Set other data (e.g. frequency offset, duplex direction, tone squelch, etc.), if desired. e Push and hold [S.MW](V/M/C) for 1 sec. to enter the select memory write mode.
1 short and 1 long beep sounds. The icon and memory channel number blink.
r Rotate [DIAL] to select a desired channel.

Call channels (C0, C1), VFO and scan edge channels (0A/0b to 24A/24b), as well as regular memory channels, can be programmed in this way.
t Push and hold [S.MW](V/M/C) for 1 sec. to program.

3 beeps sound. Memory channel number automatically increases when continuing to push [S.MW](V/M/C) for 1 sec. after programming.
NOTE: Push [H/M/L] to cancel the program and exit the select memory write mode before memory programming is nished.
[EXAMPLE]: Programming 145.440 MHz into memory channel 11 (a blank channel).

[DIAL]
Push and hold
for 1 sec.
Rotate
to select channel 11.
The VFO mode
Enter the select memory write mode. Push and hold for 1 sec. to program. Channel 11
Return to the VFO mode. 31
6
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
32
Memory bank setting

The IC-T70A/T70E has a total of 26 banks (A to Z). Regular memory channels 0 to 249 and scan edge memory channels 0A to 24b are assigned to any desired bank for easy memory management. q Push and hold [S.MW](V/M/C) for 1 sec. to enter the select memory write mode.
r Rotate [DIAL] to select a desired bank group from A to Z.

[DIAL]
w Rotate [DIAL] to select a desired memory channel. e Push [SET] to select the bAnk item.
The bank group and channel number are displayed if the selected memory channel has already been assigned to a bank. [DIAL]
t Push [BAND] to select the bank channel digit, then rotate [DIAL] to select the bank channel number from 00 to 99.
Push [BAND] to toggle the bank group selection and bank channel selection. [DIAL]
Push Rotate
y Push and hold [S.MW](V/M/C) for 1 sec. to assign the channel to the bank.
Return to the previous indication before entering the select memory write mode.
Memory bank selection

q Push [V/M/C] to select the memory mode. w Push [BAND] to enter the bank selection mode. e Rotate [DIAL] to select a desired bank (A to Z), then push [BAND].
Only programmed banks are displayed. Also regular memory channel can be selected. [DIAL] Bank channel is selected.
r Rotate [DIAL] to select the bank channel.

Only programmed channels are displayed. [DIAL]
Push
Regular memory channel is displayed.
Rotate
Bank channel is displayed.
Push
33
6
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
34
Programming memory/bank/scan name

Each memory channel can be programmed with an alphanumeric channel name for easy recognition as well as displayed independently by channel. Names can be a maximum of 6 characters. OTE: Scan name display can be turned ON or OFF in N the Initial set mode. (p. 63) q Push [V/M/C] to select the memory mode. w Push and hold [S.MW](V/M/C) for 1 sec. to enter the select memory write mode.
u Repeat step y until a desired channel name is programmed. i Push and hold [S.MW](V/M/C) for 1 sec. to set the name and exit the channel name programming state.
3 beeps sound.
OTE: Only one bank name can be programmed into each N bank. Therefore, the previously programmed bank name will be displayed when bank name is selected. Also, the programmed bank name is assigned automatically to another bank channel.
e Rotate [DIAL] to select a desired memory channel.

Select Call channels (C0 or C1) to program a call channel, or scan edge channels (0A/0b to 24A/24b) to program a scan name.
D Usable characters
(A) (b) (C) (d) (E) (F) (G) (H) (I) (J) (k) (L) (m)
r Push [SET] repeatedly to select b nAmE, m nAmE or S nAmE when programming the bank name, the memory name or the scan name, respectively. t Push and hold [SET] for 1 sec. to enter the name programming mode.
After selecting the name to be programmed, a cursor blinks for the rst character.
(n)
(O)
(P)
(q)
(R)
(S)
(t)
(U)
(V) (W) (X)
(y)
(Z)
(0)
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
y Rotate [DIAL] to select a desired character.

The selected character blinks. Push [BAND] to move the cursor right; push [SET] to move the cursor left.
(+) (-)
(=)
()
(/)
(()
())
(:)
(Space)
Programming memory/bank/scan name (continued) [EXAMPLE]: Programming the bank name VHF into the scan edge channel 1A
During memory mode, rotate to select scan edge channel 1A. Push and hold for 1 sec.
Selecting memory/bank name indication

During memory mode operation, either the programmed memory name or bank name can be displayed. q While continuing to push [SET], turn the power ON to enter the Initial set mode. w Rotate [DIAL] to select the memory name item, then rotate [VOL] to set the memory name display option.
OFF : Memory name display is turned OFF. On : Turns ON the memory name display. (default) [DIAL] Memory name setting [VOL]
Push and hold for 1 sec.
Rotate then push
to select V, .
Enter the select memory write mode. Push repeatedly to select b nAmE*2.
Select H and F with and .
Push and hold for 1 sec. to program. Select m nAmE or S nAmE*1 when programming the memory name or the scan name, respectively. *1 S nAmE can be set for scan edge channels only. *2 b nAmE can be set for bank assigned channels only.
e Push [ ] to return to the frequency display.
35
6
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
36
Display type
During memory mode operation, the transceiver has 3 display types to suit your operating style. Set the display type in the Initial set mode. q While continuing to push [SET], turn the power ON to enter the Initial set mode. w Rotate [DIAL] to select the display mode item, then rotate [VOL] to set the display type from FREq, CH or PRIV.
[DIAL] [VOL] Display mode setting
Channel number display Displays the memor y channel number. Only programmed memory channels are displayed, and modes other than the memory mode cannot be selected.
W hen the channel number display type is selected, only the following functions can be performed. - Scan function (p. 44) - Output power setting (p. 22) - Monitor function (p. 17) - Key lock function (p. 21) - DTMF transmit function (p. 66) - The scan pause timer setting, the scan resume timer setting, the DTMF memory selection, the mic gain setting and the VOX gain setting in the Set mode.
e Push [ ] to return to the frequency display. Frequency display Displays the programmed frequency. (default)
Private channel display Displays the memory channel number. Only programmed memory channels 0 to 5 are displayed, and modes other than the memory mode cannot be selected.
W hen the private channel display type is selected, only the following functions can be performed. - Output power setting (p. 22) - Monitor function (p. 17) - Key lock function (p. 21) - DTMF transmit function (p. 66)
Copying memory/call contents

This function transfers a memory channels contents to VFO (or another memory/call channel). This is useful when searching for signals around a memory channel frequency and for recalling the frequency offset, subaudible tone frequency etc. ushing and holding [S.MW](V/M/C) for 2 seconds in step P w will also copy the memory contents to the VFO. In that case, steps e and r are not necessary.
D Memory/callVFO
q Select the memory (call) channel to be copied. Push [V/M/C] repeatedly to select the memory mode or the call channel mode, then rotate [DIAL] to select a desired channel. w Push and hold [S.MW](V/M/C) for 1 sec. to enter the select memory write mode.
D Memory/callmemory/call
q Select the memory (call) channel to be copied. Push [V/M/C] repeatedly to select the memory mode or the call channel mode, then rotate [DIAL] to select a desired channel. w Push and hold [S.MW](V/M/C) for 1 sec. to enter the select memory write mode.
1 short and 1 long beep sounds. The icon and memory channel number blink. Do not hold [S.MW](V/M/C) for more than 2 seconds. Otherwise the memory contents will be copied to the VFO mode.
e Rotate [DIAL] to select VFO. r Push and hold [S.MW](V/M/C) for 1 sec. to write the selected channel contents to the VFO mode.
Returns to the VFO mode automatically. [DIAL]
e Rotate [DIAL] to select the target memory (call) channel. r Push and hold [S.MW](V/M/C) for 1 sec. again to copy.
[EXAMPLE]: Copying memory channel 11 to the VFO mode. Push and hold for 1 sec. Rotate to select VFO. Push and hold for 1 sec.
Memory mode 37
Enter the select memory write mode.
VFO is selected.
Return to the VFO mode.
6
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
38
Memory clearing
Contents of programmed memories can be cleared (erased), if desired. q Push and hold [S.MW](V/M/C) for 1 sec. to enter the select memory write mode.
1 short and 1 long beep sounds. The icon and memory channel number blink. Do not hold [S.MW](V/M/C) for more than 2 seconds. Otherwise the memory contents will be copied to the VFO mode.
e Push [SET] repeatedly to select CLEAR. r Push and hold [S.MW](V/M/C) for 1 sec. to clear the contents.
3 beeps sound. The cleared channel changes into a blank channel Return to the select memory write mode. Memory channel number blinks.
t Push [H/M/L] to exit the select memory write mode. NOTE: Be careful! the contents of cleared memories CANNOT be recalled.
w Rotate [DIAL] to select a desired memory channel to be cleared. [EXAMPLE]: Clearing memory channel 14.
[DIAL]
Push and hold
for 1 sec.
Rotate
to select a desired channel.
The VFO mode
Enter the select memory write mode. Push repeatedly to select CLEAR. for 1 sec to clear.
Channel 14
Push and hold
Push to return to the VFO mode.
Erasing/transferring bank contents

The bank contents of programmed memory channels can be cleared or reassigned to another memory bank. INFORMATION: Even if the memory bank contents are cleared, the memory channel contents still remain programmed. q Select a desired banks contents to be transferred or erased from the bank. (p. 33) Push [BAND] to enter the memory bank selection mode. Rotate [DIAL] to select a desired memory bank group, then push [BAND]. Rotate [DIAL] to select the bank channel.
[DIAL]
Do not hold [S.MW](V/M/C) for more than 2 seconds. Otherwise the memory contents will be copied to the VFO.
e Push [SET] repeatedly to select bAnk.
r Push [BAND] to toggle the bank channels selection or the bank group selection. t Rotate [DIAL] to select a desired bank group or channel to be transferred. Or, select the -- -- -- -- display when erasing the contents from the bank.
[DIAL] To transfer the bank contents to ch 11 in Bank b.
Bank channel is displayed. To erase
w Push [S.MW](V/M/C) for 1 sec. to enter the select memory write mode.
1 short and 1 long beep sounds. Automatically displays the original memory channel number, and then the icon and memory channel number blink. is displayed.
y Push [S.MW](V/M/C) for 1 sec. to erase/transfer the bank contents.
39
SCAN OPERATION
Scan types
Scanning automatically searches for signals and makes it easier to locate new stations for contact or listening purposes.
7
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
40
FULL SCAN (p. 42)

144 MHz band Scan Jump 440 MHz band Scan
SELECTED BAND SCAN (p. 42)

Repeatedly scans all frequencies over the entire band. Some frequency ranges are not scanned, depending on the frequency coverage of the transceivers version.
Band edge Scan Jump Band edge
Repeatedly scans all frequencies over the entire selected band.
PROGRAMMED SCAN (p. 42)

Band edge Scan edges xxA Scan Jump Band xxB edge
FREQUENCY/MEMORY SKIP FUNCTION

Band edge Scan SKIP Jump SKIP Band edge
Repeatedly scans between two user-programmed frequencies. Used to check for frequencies within a specified range, such as repeater output frequencies, etc.
Skips unwanted frequencies or channels that inconveniently stop scanning. This setting can be turned ON or OFF in the select memory write mode. (p. 46)
PROGRAMMED LINK SCAN (pp. 42, 57)

Repeatedly scans user-programmed frequencies selected in the P-LInk item in the Set mode.
The frequency skip scan function can be turned ON or OFF in the Set mode. When this function is set to ON, the specied frequencies are skipped during VFO scan. (p. 55)
The P icon appears in the VFO mode.
SCAN OPERATION
Scan types (continued)
MEMORY (SKIP) SCAN (p. 44)

SKIP
M1 M0 M 249 M6 M5 M2 M3 M4
BAND MEMORY (SKIP) SCAN (p. 44)

SKIP
M1 M0 M 249 M2 M3
SKIP
Repeatedly scans memory channels, except those set as skip channels. Skip channels can be turned ON or OFF in the select memory write mode. (p. 46)
SKIP
M4
440 MHz band

M6 M5
440 MHz band
Repeatedly scans memory channels in the same band as the band currently displayed.
Example: While scaning the 144 MHz band
ALL/SELECTED BANK SCAN (p. 45)

SKIP
A00 A99 A98 A05 A04 A01 A02 A03
BANK-LINK SCAN (pp. 45, 46)

Repeatedly scans bank channels selected in the b-LInk item in the Set mode.
SKIP
Repeatedly scans all bank channels or selected bank channels. The skip scan is also available.
DUPLEX SCAN (pp. 42, 44)

During duplex scan operation, repeatedly scans the transmit and receive frequencies of the duplex channel you are operating on.
41
SCAN OPERATION
7
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
42
Full/band/programmed scan
q Push [V/M/C] to select the VFO mode.
Push [BAND] to select a desired frequency band.
t Push [SCAN](H/M/L) to start the scan.

The scan pauses when a signal is received. Rotate [DIAL] to change the scanning direction. This also resumes scanning. Push [V/M/C] to stop the scan. Push [BAND] to change the band during band scan, or change the scan edge during programmed scan/program link scan. While continuing to push [SCAN](H/M/L) in step e , rotate [DIAL] to select a desired scanning type, then release the key also starts the scan.
w Set the squelch level. e Push and hold [SCAN](H/M/L) for 1 sec. to enter the scan type selection mode. r Rotate [DIAL] to select a desired scanning type.
Select ALL for full scan, bAnd for band scan, P-LInk x for programmed link scan (x= 0 to 9), PROGxx for programmed scan (xx= 0 to 24; only programmed scan edge numbers are displayed), dUP (appears only when duplex operation is set) for a duplex scan. [DIAL] Push and hold for 1 sec. Rotate Full scan Programmed scan
During full/band scan
During programmed scan
Band scan
Selectable from 0 to 24, if programmed. (p. 43) Duplex scan
The scan link name or scan name can be displayed instead of P-LInk x for program link scan (x= 0 to 9), PROGxx for programmed scan (xx= 0 to 24) when scan link name or scan name is programmed and set to ON in the Initial set mode. Scan link name or scan name is not displayed during scan.
Programmed link scan Selectable from 0 to 9. See page 57 for details of the programming.
SCAN OPERATION
Scan edges programming

Scan edges can be programmed in the same manner as memory channels. Scan edges are programmed into scan edge memory channels, 0A/0b to 24A/24b. q Push [V/M/C] to select the VFO mode. w Set a desired frequency: Push [BAND] to select a desired band. Rotate [DIAL] to set a desired frequency. Program different frequencies in A and b. Set other data (e.g. frequency offset, duplex direction, tone squelch, etc.), if desired. e Push and hold [S.MW](V/M/C) for 1 sec. to enter the select memory write mode.
r Rotate [DIAL] to select a desired programmed scan edge channel from 0A to 24A. t Push and hold [S.MW](V/M/C) for 1 sec. to program. 3 beeps sound.
The other scan edge channel b, 0b to 24b, is automatically selected when continuing to push [S.MW](V/M/C) after programming.
y To program a frequency for the other pair of scan edges, 0b to 24b, repeat steps w and t.
If the same frequency is programmed into a pair of scan edges, programmed scan will not function.
[DIAL]
[EXAMPLE]: Programming 145.300 MHz into scan edges 3A. Push and hold for 1 sec. Rotate 3A. to select Push and hold for 1 sec.
The VFO mode
Enter the select memory write mode.
3A is selected.
Return to the VFO mode.
43
SCAN OPERATION
7
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
44
Memory scan
MPORTANT!: To perform a memory scan, 2 or more I memory channels MUST be programmed, otherwise the scan will not start. q Push [V/M/C] repeatedly to select the memory mode. w Set the squelch level. e Push and hold [SCAN](H/M/L) for 1 sec. to enter the scan type selection mode. r Rotate [DIAL] to select a desired scanning type.
ALL for all memory scan, bAnd for band memory scan, dUP (appears only when duplex operation is set) for duplex scan. [DIAL] Push and hold for 1 sec. Rotate All memory scan Duplex scan During memory scan

The scan pauses when a signal is received. Rotate [DIAL] to change the scanning direction. This also resumes scanning. Push [V/M/C] to stop the scan. While continuing to push [SCAN](H/M/L) in step e , rotate [DIAL] to select a desired scanning type, then release the key also starts the scan.
Band memory scan
SCAN OPERATION
Memory bank scan

MPORTANT!: To perform a memory bank scan, 2 or more I bank channels MUST be programmed, otherwise the scan will not start. q Select the memory bank mode. Push [V/M/C] to select the memory mode. Push [BAND] to enter the memory bank selection mode. Rotate [DIAL] to set a desired bank (A to Z), then push [BAND]. w Set the squelch level. e Push and hold [SCAN](H/M/L) for 1 sec. to enter the scan type selection mode.
[DIAL] Push and hold for 1 sec. Rotate All bank scan Bank scan During all bank/bank link scan During bank scan
r Rotate [DIAL] to select a desired scanning type.

Select ALL for all bank scan, b-LInk for bank link scan or bAnk-x for bank scan (x= A to Z; only programmed bank groups are displayed.), dUP (appears only when duplex operation is set) for duplex scan.

The scan pauses when a signal is received. Rotate [DIAL] to change the scanning direction. This also resumes scanning. Push [V/M/C] to stop the scan. Push [BAND] to change the bank during a bank scan. While continuing to push [SCAN](H/M/L) in step e , rotate [DIAL] to select a desired scanning type, then release the key also starts the scan.
Selectable from A to Z, if programmed. (p. 32) Bank link scan Duplex scan
emory bank scan skips any memory channels in the seM lected bank that are set to SKIP or PSKIP. Memory bank scan stops at the rst channel when all channels in a bank are set to SKIP or PSKIP.
See page 56 for details of the bank link programming.
45
SCAN OPERATION
7
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
46
Skip channel/frequency setting

Memory channels can be set to be skipped during memory skip scan. In addition, memory channels can be set to be skipped during both memory skip scan and frequency skip scan. This is useful to speed up the scan rate. q Select a memory channel: Push [V/M/C] to select the memory mode. Rotate [DIAL] to select a desired channel to be a skip channel/frequency.
[DIAL]
e Push [SET] repeatedly to select the SkIP item.
Push
repeatedly.
r Rotate [DIAL] to select the skip condition from SkIP, PSkIP or OFF for the selected channel.
PSkIP : The channel is skipped during a memory/bank scan, and the programmed frequency is skipped during VFO scan, such as a programmed scan. SkIP : The channel is skipped during a memory or bank scan. OFF : The channel is scanned during any scan.
w Push and hold [S.MW](V/M/C) for 1 sec. to enter the select memory write mode.
t Push and hold [S.MW](V/M/C) for 1 sec. to store the skip condition into memory.
or P icon appears, depending on the skip selection in step r. appears appears
Skip channel setting
Program skip setting
SCAN OPERATION
Scan resume setting

D Scan pause timer
The scan pauses while receiving signals, depending on the scan pause time. It can be set from 2 to 20 seconds or unlimited. q Push [SET] to enter the Set mode. w Rotate [DIAL] to select the scan pause timer item. e Rotate [VOL] to select a desired scan pause time from 220 seconds (2 seconds steps) or HOLd.
220 : Scan pauses for 220 seconds while receiving a signal. HOLd : Scan pauses on a received a signal until it disappears.
D Scan resume timer

The scan restarts after the signal disappears, depending on the resume time. It can be set from 05 seconds or unlimited. q Push [SET] to enter the Set mode. w Rotate [DIAL] to select the scan resume timer item. e Rotate [VOL] to select a desired scan resume time from 05 seconds (1 second steps) or HOLd.
0 : Scan restarts immediately after the signal disappears. 15 : Scan restarts 15 seconds after the signal disappears. HOLd : Scan remains paused on the received signal according to the scan pause timer even if it disappears. Rotate [DIAL] to manually resume the scan.
r Push [V/M/C] to return to the frequency display. r Push [V/M/C] to return to the frequency display. he scan resume timer must be set shorter than the scan T pause timer, otherwise this timer will not be activated.
47
PRIORITY WATCH
Priority watch types
While operating on a VFO frequency or scanning, the priority watch checks for signals on the set priority frequency every 5 seconds. The transceiver has four priority watch types to suit your needs. The watch resumes according to the selected scan resume setting. See page 47 for details. OTE: If the pocket beep function is activated, the transN ceiver automatically selects the tone squelch/DTCS squelch function when priority watch starts.
8
SKIP
MEMORY SCAN WATCH

While operating on a VFO frequency, priority watch checks for signals on each memory channel in sequence.
The memory skip function and/or memory bank scan is useful to speed up the scan. 5 seconds VFO frequency
Mch 0 Mch 1 Mch 2 Mch 249
VFO SCAN WATCH

While scanning in the VFO mode, priority watch checks for signals on the selected channel every 5 seconds.
5 seconds VFO scan Memory (Call) channel
D About priority beep function

When receiving a signal on the priority frequency, you can be alerted with beeps and a blink S icon. This function can be activated when the priority watch function is turned ON.
MEMORY/CALL CHANNEL WATCH

While operating on a VFO frequency, priority watch checks for a signal on the selected channel every 5 seconds.
A memory channel with skip information can be watched. 5 seconds VFO frequency Memory (Call) channel
VFO/MEMORY SCAN WATCH

While scanning in the VFO mode, priority watch checks for signals on each memory channel in sequence.
The memory skip function and/or memory bank scan is useful to speed up the scan. 5 seconds VFO scan
SKIP
Mch 0 Mch 1 Mch 2 Mch 249
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
48
PRIORITY WATCH
Priority watch operation

D Memory/call channel and memory scan watch
q Select the VFO mode, then set an operating frequency. w Select the channel(s) to be watched. For memory channel watch: Select a desired memory channel. For call channel watch: Select a desired call channel. For memory scan watch: Select the memory mode, or a desired bank group. Push and hold [SCAN](H/M/L) for 1 sec. to enter the scan type selection mode. Rotate [DIAL] to select a desired scan type, then push [SCAN](H/M/L) again to start the memory/bank scan. e Push [SET] to enter the Set mode. r Rotate [DIAL] to select the priority watch set item, then rotate [VOL] to select On.
Select bELL if the priority beep function is desired. During priority watch
Monitors VFO frequency for 5 seconds.
Pauses on a memory or call channel when a signal is received.
During priority watch with priority beep
A beep tone sounds and S icon blinks when a signal is received on a memory or call channel.
t Push [V/M/C] to exit the Set mode and start the watch.
The PRIO icon appears. The transceiver checks the memory/bank channel(s) or call channel every 5 seconds. The watch resumes according to the selected scan resume setting. (p. 47)
y Push [V/M/C] to cancel the watch. 49
PRIORITY WATCH
8
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
50
D VFO scan watch

q Select the channel(s) to be watched. For memory channel watch: Select a desired memory channel. For call channel watch: Select a desired call channel. For memory scan watch: Select the memory mode, or a desired bank group. Push and hold [SCAN](H/M/L) for 1 sec. to enter the scan type selection. Rotate [DIAL] to select a desired scan type, then push [SCAN](H/M/L) again to start memory/bank scan. w Push [SET] to enter the Set mode. e Rotate [DIAL] to select the priority watch set item, then rotate [VOL] to select On.
Select bELL if the priority beep function is desired.
u Push [SCAN](H/M/L) to start the VFO scan watch.

The transceiver checks the memory/bank channel(s) or call channel every 5 seconds. The watch resumes according to the selected scan resume setting. (p. 47)
i Push [V/M/C] to cancel the watch.

During priority watch
Searches VFO frequencies for 5 seconds.
Pauses on a memory or call channel when a signal is received.
During priority watch with priority beep
r Push [V/M/C] to exit the Set mode and start the watch.
PRIO icon appears.
t Push and hold [SCAN](H/M/L) for 1 sec. to enter scan type selection mode. y Rotate [DIAL] to select a desired scan type from ALL, bAnd, P-LInk x (x= 09), PROGxx (xx= 024) and dUP.
A beep tone sounds and S icon blinks when a signal is received on a memory or call channel.
SET MODES
D Entering and using the Initial set mode
The Initial set mode can be accessed at power ON, and allows you to set seldom-changed settings to suit your preference and operating style. q Push and hold [ ] for 1 sec. to turn the power OFF. w While continuing to push [SET], turn the power ON to enter the Initial set mode. e Rotate [DIAL] to select the desired set item. r Rotate [VOL] to set the desired value or option. t Push [ ] to return to the frequency display, or repeat steps w and e to set other items.
[DIAL] [VOL]
General
D Entering and using the Set mode
The Set mode is used to change the settings of the transceivers functions. q Push [SET] to enter the Set mode. w Rotate [DIAL] to select the desired set item. e Rotate [VOL] to set the desired value or option. r Push [V/M/C] to return to frequency display, or repeat steps w and e to set other items.
[DIAL] [VOL]
51
SET MODES
9
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
52
Set mode item list

Guidance Item
Repeater tone frequency TSQL frequency DTCS code DTCS polarity Tuning step Frequency offset Reverse duplex function Operating mode Weather alert Priority watch Scan pause timer Scan resume timer Program skip function Bank link Programmed scan link DTMF TX key DTMF memory setting MIC gain VOX function VOX gain VOX delay VOX time-out timer
Initial set mode item list

Page p. 53 p. 53 p. 53 p. 53 p. 54 p. 54 p. 54 p. 54 p. 54 p. 55 p. 55 p. 55 p. 55 p. 56 p. 56 p. 58 p. 58 p. 58 p. 58 p. 58 p. 59 p. 59 Guidance Item
Microphone simple mode Auto power OFF Display backlight Beep output level Auto repeater Power save Voltage indication DTMF speed LCD contrast PTT lock Busy lockout Time-out timer Squelch delay Monitor key action Dial speed acceleration Memory name Scan name Display type HS-95 selection Auto low power
Page p. 59 p. 59 p. 60 p. 60 p. 60 p. 61 p. 61 p. 61 p. 62 p. 62 p. 62 p. 62 p. 62 p. 63 p. 63 p. 63 p. 63 p. 64 p. 64 p. 64
SET MODES
Set mode items

D Repeater tone frequency (R TONE)
Selects one of 50 subaudible tone frequencies used to access the repeaters.
67.0254.1 Hz (default: 88.5 Hz)
D DTCS code (CODE)

Selects one of 104 DTCS (both encoder/decoder) codes.
023754 (default: 023)
Available DTCS codes
D TSQL frequency (C TONE)

Selects one of the tone frequencies for tone squelch or the pocket beep function.
67.0254.1 Hz (default: 88.5 Hz)
023 025 026 031 032 036 043 047 051 053
054 065 071 072 073 074 114 115 116 122
125 131 132 134 143 145 152 155 156 162
165 172 174 205 212 223 225 226 243 244
245 246 251 252 255 261 263 265 266 271
274 306 311 315 325 331 332 343 346 351
356 364 365 371 411 412 413 423 431 432
445 446 452 454 455 462 464 465 466 503
506 516 523 526 532 546 565 606 612 624
627 631 632 654 662 664 703 712 723 731
732 734 743 754
Available subaudible tone frequencies

67.0 69.3 71.9 74.4 77.0 79.7 82.5 85.4 88.5 91.5 94.8 97.4 100.0 103.5 107.2 110.9 114.8 118.8 123.0 127.3 131.8 136.5 141.3 146.2 151.4 156.7 159.8 162.2 165.5 167.9 171.3 173.8 177.3 179.9 183.5 186.2 189.9 192.8 196.6 199.5 203.5 206.5 210.7 218.1 225.7 229.1 233.6 241.8 250.3 254.1
D DTCS polarity (DTCS P)

Selects the DTCS polarity between both n (TX/RX: normal), tn-RR (TX: normal, RX: reverse), tR-Rn (TX: reverse, RX: normal) and both R (TX/RX: reverse). (default: both n) The DTCS codes polarity for transmitting or receiving can be independently set by this item.
he transceiver has 50 tone frequencies, and conseT quently their spacing is narrow compared with units having 38 tones. Therefore, some tone frequencies may receive interference from adjacent tone frequencies. 53
SET MODES
9
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
54
D Tuning step (TS)

Selects the tuning step between 5, 10, 12.5, 15, 20, 25, 30, 50, 100, 125 and 200 kHz for the dial operation.
D Reverse duplex function (DUP.REV)

Turns the reverse duplex function ON or OFF. (default: OFF)
5.0 kHz tuning step The default value may differ, depending on the selected frequency band (before accessing the Set mode) and the transceiver version.
Reverse function is OFF
D Operating mode (MODE)

Sets the operating mode between WIdE (FM mode) and nARROW (FM-N mode). (default: WIdE)
D Frequency offset (OFFSET)

Sets the frequency offset for duplex operation (repeater) within the range of 0 to 59.995 MHz. FM mode setting
D Weather alert (WX.ALT)

0.600 MHz setting The default value may differ, depending on the selected frequency band (before accessing the Set mode) and transceiver version. he selected tuning step in the VFO mode is used when T setting the frequency offset.
U.S.A. version only
Turns the weather alert function ON or OFF. (p. 72) (default: OFF)
SET MODES D Scan resume timer (RESUME)

Selects the scan resume time of a pause after the received signal disappears. (default: 2)
0 : Scan resumes immediately after the received signal disappears. 15 : Scan pauses 15 seconds after the received signal disappears. HOLd : Scan remains paused on the received signal according to the scan pause timer, even if it disappears. Rotate [DIAL] to manually resume the scan.
D Priority watch (PRIO)

Activates priority watch or priority watch with priority beep. (default: OFF)
OFF : The priority watch is turned OFF. On :T he transceiver checks the memory channel frequency every 5 seconds. bELL : The transceiver checks the memory channel frequency every 5 seconds. You can be alerted with beeps and a blinking S icon.
D Scan pause timer (PAUSE)

Selects the scan pause time. When receiving signals, the scan pauses according to the scan pause timer. (default: 10)
220 : Scan pauses for 220 seconds while receiving a signal in 2 seconds steps. HOLd : Scan pauses on a received signal until it disappears.
The scan resume timer must be set shorter than the scan pause timer (previous item), otherwise this timer will not be activated.
D Program skip scan (P SKIP)

Turns the programmed skip scan function ON or OFF for a VFO scan operation (full scan, programmed scan, etc.). (default: On)
55
SET MODES D Memory bank link function (B-LINK)

Turns the memory bank link function ON (default) or OFF. The link function provides continuous bank scan, scanning all channels in the selected banks during bank scan.
9
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
56
D Program scan link function (P-LINK)

Sets the program scan link function. During program scan, link function performs a continuous program scan in the selected program scan number during program scan. Default settings for LInk0 to LInk9; PROG 1 to PROG 24 are linked, but PROG 0 is not linked.
Bank link setting q P ush and hold [SET] for 1 sec. to enter the bank link setting.
Conrming program scan link q Rotate [VOL] to select the program scan link number that you want to conrm.
w Rotate [DIAL] to select the bank that you want to change the link setting. e Rotate [VOL] to select the option.
w Push and hold [SET] for 1 sec. to enter the program scan link setting.
LInk appears.
Setting is ON
Setting is OFF e P ush and hold [SET] for 1 sec., then rotate [DIAL] to conrm the linked program scans.
r Rotate [DIAL] to select next bank and repeat steps w and e, or push [BAND] to exit the BANK link setting.
r Push [BAND] twice to exit the program scan link setting.
SET MODES
Program scan link setting q Rotate [VOL] to select the program scan link number that you want to change.
Program scan link name programming q Rotate [VOL] to select the program scan link number for which you want to program a name.
LInk appears.
LInk appears.
e Rotate [DIAL] to select the option, Add or CLEAR.
e Rotate [DIAL] to select nAmE. r P ush and hold [SET] for 1 sec. to enter the name programming.
r P ush and hold [SET] for 1 sec., then rotate [DIAL] to select the desired program scan.
When Add is selected in step e , only non-linked program scans are displayed. When CLEAR is selected in step e, only linked program scans are displayed.
t Rotate [DIAL] to select the desired character, number, symbol or space; push [BAND] or [SET] to move the cursor right or left, respectively. y When the cursor is on the 6th digit, push [BAND] to program the scan link name and exit the setting.
t Push and hold [SET] for 1 sec. to set the program scan link setting. y Repeat steps r and t to add or clear the program scan to or from the link, or push [BAND] to exit the program link scan setting. 57
u Push [BAND] to exit the program link setting. i Repeat steps from q to u to program the program link scan name, or push [V/M/C] to exit the Set mode.
SET MODES D DTMF TX key (DTMF-T)

Selects the method to transmit a DTMF code sequence. While continueing to push [PTT], push one of the keys, [0] to [9], [A](SET), [B](BAND), [C](H/M/L), [D](V/M/C), [M] (indication: E) or [#] (indication: F).
KEy mEm t-CALL : Transmits the appropriate DTMF code assigned to the key. (default) : Transmits the programmed DTMF code sequence in the DTMF memory channel assigned to the key. : No DTMF code can be transmitted. However, while continuing to push [PTT], push [MONI](BAND) to transmit a 1750 Hz tone burst signal.
9
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
58
D Microphone gain (MIC G)

Sets the microphone gain to between 1 and 4 to suit your preference. Higher values make the microphone more sensitive to your voice. (default: 2)
NOTE: When using the VOX function, we recommend setting the microphone gain to 3. However, you can adjust it to suit your operating environment, including the headset performance you are using.
D VOX function (VOX)

Turns the VOX function ON or OFF. (p. 80) (default: On)
D DTMF memory (DTMF)

Program the DTMF memory channels. (p. 65)
D VOX gain (VOX LV)

Sets the VOX gain to between 1 and 10. Higher values make the VOX function more sensitive to your voice. To turn the VOX function OFF, select OFF. (default: 5)
NOTE: Set the microphone gain before setting the VOX gain. See page 80 for details of the VOX function.
SET MODES
Initial set mode items

D VOX delay (VOX.DLY)
Sets the VOX delay to between 0.5, 1.0, 1.5, 2.0, 2.5 and 3.0 seconds. The VOX delay is the amount of time the transmitter stays ON after you stop speaking. (default: 0.5)
D Microphone simple mode (MIC S)

Microphone simple mode is used to assign the essential operations to the four switches (S1 to S4) on the remote control unit. (p. 82)
SImPLE nORm-1 (default) nORm-2
D VOX time-out timer (VOXTOT)

Sets the VOX time-out timer to between 1, 2, 3, 4, 5, 10 and 15 minutes to prevent accidental prolonged transmission for the VOX function. To turn the function OFF, select OFF. (default: 3)
D Auto power OFF (AP OFF)

The transceiver can turn itself OFF automatically after a specied time. Activating a control restarts the time-out. The transceiver beeps before turning OFF. 30, 60, 90, 120 minutes and OFF can be specied. The specied period is retained even when the transceiver is turned OFF by the auto power-off function. To cancel the function, select OFF. (default: OFF)
he VOX time-out timer must be set shorter than the timeT out timer, otherwise this timer will not be activated.
59
SET MODES
9
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
60
D Display backlighting (LIGHT)

The transceiver has a display backlighting with a 5 second timer for night time operation. The display backlighting can be turned ON continuously or turned OFF. (default: Auto1)
OFF On Auto1 Auto2 : The backlight is turned OFF. : The backlight is continuously ON. : Lights when an operation is performed, then goes out after 5 seconds. : Lights when an operation is performed, then goes out after 5 seconds with a battery pack or battery case, or stays ON when using the external power supply (more than 10 V DC).
D Auto repeater (AUTORP)

U.S.A. and Korean versions only The auto repeater function automatically turns the duplex operation and tone encoder ON or OFF. The offset and repeater tone settings are not changed by the auto repeater function. Reset these frequencies, if necessary. U.S.A. version:
OFF : The auto repeater function is turned OFF. R1 :A ctivates for duplex only. (default) R2 : Activates for duplex and tone.
Korean version:
D Beep output level (BEEPLV)

Turns the key-touch beep ON or OFF. Sets the beep sound level to between 1 and 9. (default: 4)
OFF : The auto repeater function is turned OFF. On :A ctivates for duplex and tone. (default)
SET MODES D Voltage indication (VOLT)

The power voltage, battery voltage or external power supply voltage, is displayed at power ON. This setting can be turned ON or OFF. (default: On)
OFF On : The power voltage display is skipped. : The power voltage is displayed at power ON.
D Power save (P SAVE)

The power save function allows you conserve battery life by selecting the duty cycle of the receiver. Select the ratio of the power save time to the standby time. (default: Auto)
OFF 2 8 16 32 Auto : Turns the function OFF. : Sets the duty cycle to 1:2. : Sets the duty cycle to 1:8. : Sets the duty cycle to 1:16. : Sets the duty cycle to 1:32. : Transceiver sets 1:2 duty ratio when receiving no signal for 5 seconds, then it sets 1:16 after 60 seconds has past.
No signal 5 sec. 125 msec. 1000 msec.
D DTMF speed (DTMF-S)

Select the desired DTMF transmission speed from 100, 200, 300 or 500 msec. (default: 100)
100 200 300 500 : 100 msec. interval; 5.0 characters per second : 200 msec. interval; 2.5 characters per second : 300 msec. interval; 1.6 characters per second : 500 msec. interval; 1.0 character per second
Circuit ON Circuit OFF
62.5 msec. 60 sec.
NOTE: Power save function is disabled when using an external power supply (more than 10 V DC).
61
SET MODES D LCD contrast (CONT)

Selects the LCD contrast.
Auto
9
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
62
D Time-out timer (TOT)

(default: Auto) To prevent accidental prolonged transmission, the transceiver has a time-out timer. This function cuts transmission OFF after 130 min. of continuous transmission. This timer can be cancelled. (default: 5)
OFF 1 to 30 : The time-out timer is turned OFF. : The transmission is cut OFF after the set period elapses.
HI LO
: Sets the contrast to high. However, if the transceiver is exposed to high temperatures, it automatically sets the contrast to low. : Sets the contrast to high. : Sets the contrast to low.
D PTT lock (PTT LK)

Turns the PTT lock function ON or OFF. To prevent accidental transmission, the transceiver has the PTT lock function. (default: OFF)
Approx. 10 seconds before the time-out timer is activated, the transceiver emits a beep tone as a warning. B E CAREFUL! The transceiver will become hot when this time-out timer function is turned OFF or set to a long time period, and transmission is made for long periods.
D Squelch delay (SQL DL) D Busy lockout (LK OUT)

Turns the busy lockout function ON or OFF. This function inhibits transmission while receiving a signal or when the squelch is open. (default: OFF) Sets the squelch delay between short and long. The delay prevents the squelch from repeatedly opening and closing while receiving the same signal. (default: SHORt)
SHORt LOnG : Sets the squelch delay to short. : Sets the squelch delay to long.
SET MODES D Memory name (NAME)

The memory name is displayed during memory mode, or the memory bank name is displayed during memory bank selection. (default: OFF)
OFF On : The frequency of the selected memory channel is displayed. : The pre-programmed memory name or memory bank name is displayed.
D Monitor key action (MONI)

The monitor key, [MONI](BAND), can be set as a sticky key. When set to the sticky condition, each push of [MONI](BAND) toggles the monitor function ON or OFF. (default: PUSH)
PUSH : Push and hold [MONI](BAND) to monitor the frequency. HOLd : Push and hold [MONI](BAND) for 1 sec. to monitor the frequency and push again to cancel it.
D Dial speed acceleration (DIAL S)

The dial speed acceleration automatically speeds up the tuning dial speed when rotating [DIAL] rapidly. (default: On)
OFF On : The dial speed acceleration is turned OFF. : The dial speed acceleration is tuned ON.
D Scan name (S NAME)

The programmed scan, programmed link scan or bank name is displayed during scan type selection. (default: On)
OFF On : The programmed scan, programmed link scan or bank name is not displayed. : The programmed scan, programmed link scan or bank name is displayed.
63
SET MODES D Display type (DISP M)

Selects the display type for memory mode operation. (default: FREq)
FREq : Displays the programmed frequency. CH :D isplays the memory channel number. Operable functions, configurable items in the Set mode, and selectable modes will be restricted. PRIV : D isplays the memory channel number. Operable channel, functions and selectable mode are restricted.
9
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
64
D Auto low power (AUTOLP)

Turns the auto low power function ON or OFF. When the temperature goes below 0C (+32F), the function automatically sets the output power to low. In that case, the transmit power selections (High/Mid) are also disabled. (default: OFF)
D Headset selection (HS SEL)

Selects the connected headset type between the HS-95 and other. When using an optional headset HS-95, this setting must be set to HS-95. (default: OtHER)
10
OTHER FUNCTIONS
[DIAL]
Programming a DTMF code sequence

DTMF codes are used for autopatching, accessing repeaters, controlling other equipment, etc. The transceiver has 16 DTMF memory channels (d0d9, dA, db, dC, dd, dE, dF) for storage of often-used DTMF codes of up to 24 digits. q Push [SET] to enter the Set mode. w Rotate [DIAL] to select the DTMF programming item. e Rotate [VOL] to select a desired DTMF memory channel.
If programmed, previously programmed the DTMF code is displayed. [DIAL] [VOL]
t Rotate [DIAL] to select the characters.

09, A, b, C, d, E and F are selectable. Up to 24 digits can be programmed. Push [BAND] to move the cursor right; push [SET] to move the cursor left.
y Repeat step t until the desired code is input.
Next display appears after 6th digit has been input. : 1st display : 3rd display Blank channel indication DTMF memory channel : 2nd display : 4th display
r Push and hold [SET] for 1 sec. to enter the programming mode.
The cursor is blinking during programming mode.
If a digit is mistakenly programmed, push [SET] (or [BAND]) repeatedly to select the digit, then rotate [DIAL] to correct it. Or rotate [DIAL] to select _ to erase on and after the digits. Programmed memories will be cleared by this operation on the 1st digit.
u Push [BAND] twice to program the DTMF code and exit the programming mode.
After the 24th digit is input, the transceiver automatically stores the code sequence and returns to step e.
i Push [V/M/C] to return to the frequency display. 65
OTHER FUNCTIONS
10
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
66
Transmitting a DTMF code sequence

The transceiver has 3 methods of transmitting a DTMF code sequence. Select a desired option in the Set mode. q Push [SET] to enter the Set mode. w Rotate [DIAL] to select the DTMF TX key item.
[DIAL] [VOL]
D Manual DTMF code transmission

First, set the DTMF TX key to kEy in the Set mode. While continuing to push [PTT], push the desired keys to transmit a DTMF code sequence manually.
[0][9], [A](SET), [B](BAND), [C](H/M/L), [D](V/M/C), [M](.) or [#] sends 09, A, B, C, D, M or #.
[PTT]
e Rotate [VOL] to select a desired DTMF key setting.

kEy :T ransmits the appropriate DTMF code assigned to the pushed key. (default) mEm : T ransmits the programmed DTMF code sequence in the DTMF memory channel assigned to the pushed key. t-CALL : No DTMF code can be transmitted. However, while continuing to push [PTT] , pushing [MONI] (BAND) transmits a 1750 Hz tone burst signal.
DTMF code keys
r Push [V/M/C] to return to the frequency display.
10
OTHER FUNCTIONS
Transmitting a DTMF code sequence (continued)
Setting DTMF transfer speed

The DTMF transfer speed can be selected. q While continuing to push [SET], turn the power ON to enter the Initial set mode. w Rotate [DIAL] to select the DTMF transfer speed item, then rotate [VOL] to select the transfer speed.
DU sing a DTMF memory channel

First, set the DTMF TX key to mEm in the Set mode. While continuing to push [PTT], push one of the keys to transmit the programmed DTMF code sequence in the DTMF memory.
P ushing [0] to [9] , [A] (SET), [B] (BAND), [C] (H/M/L), [D](V/M/C), [M](.) or [#] transmits d0d9, dA, db, dC, dd, dE or dF.
D1 750 Hz tone
o access some European repeaters, the transceiver must T transmit a 1750 Hz tone burst signal.
This tone can be used as a Call signal in countries out of Europe.
First, set the DTMF TX key to t-CALL in the Set mode. While continuing to push [PTT], push and hold [MONI] (BAND) for 1 or 2 sec. to transmit a 1750 Hz tone burst signal.
100 : T ransfer the DTMF tones at about 100 msec. per tone. (default) 200 : T ransfer the DTMF tones at about 200 msec per tone. 300 : T ransfer the DTMF tones at about 300 msec per tone. 500 : T ransfer the DTMF tones at about 500 msec per tone. e Push [ ] to return to the frequency display.
67
OTHER FUNCTIONS
10
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
68
Tone frequency and DTCS code

D Tone and DTCS squelches
The tone squelch (CTCSS) or DTCS squelch opens only when receiving a signal containing a matching subaudible tone or DTCS code, respectively. You can silently wait for calls from group members using the same tone or code. Separate tone frequencies can be set for repeater and tone squelch/pocket beep operation.
D Setting subaudible tones for tone squelch

q Push [SET] to enter the Set mode. w Rotate [DIAL] to select the CTCSS tone frequency item.
[DIAL]
D Reverse tone/DTCS squelch

The reverse tone/DTCS squelch is convenient if you want to ignore a specific signal. The transceiver mutes the squelch when a signal with the matched tone or code is received. T SQL-R / DTCS-R is displayed when the reverse tone/ DTCS squelch is set.
e Rotate [VOL] to select a desired CTCSS tone frequency.

Each operating band and each memory channel have independent settings. See page 53 for available tone frequencies for details.
D Pocket beep
These functions use subaudible tones or DTCS codes for calling and can be used as a common pager to inform you that someone has called while you were away from the transceiver.
10
OTHER FUNCTIONS
Tone frequency and DTCS code (continued)
D Setting DTCS code for DTCS squelch

q Push [SET] to enter the Set mode. w Rotate [DIAL] to select the DTCS code item.
[DIAL]
D Setting DTCS polarity

q Push [SET] to enter the Set mode. w Rotate [DIAL] to select the DTCS polarity item.
[DIAL]
e Rotate [VOL] to select a desired DTCS code.

Each operating band and each memory channel have independent settings. See page 53 for available DTCS codes for details.
e Rotate [VOL] to select a desired DTCS polarity mode.

both n tn-RR tR-Rn both R : Normal phase is used for both TX and RX. (Default) : Normal phase is used for TX; Reverse phase for RX. : Reverse phase is used for TX; Normal phase for RX. : Reverse phase is used for both TX and RX.
r Push [V/M/C] to return to the frequency display. TCS phase can be selected in the dtCS P item. See D next content for more details.
69
OTHER FUNCTIONS
10
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
70
Tone/DTCS squelch
q S et a desired operating frequency, and then set a CTCSS tone or DTCS code. w Push and hold [TONE](0) for 1 sec. repeatedly to activate the tone or DTCS squelch. (T SQL or DTCS)
S ubaudible tone encoder T, pocket beep (tone squelch) ST SQL, tone squelch T SQL, DTCS beep SDTCS, DTCS squelch DTCS, tone squelch reverse T SQL-R, DTCS squelch reverse DTCS-R and no tone operation are selectable in order. While continuing to push [TONE](0), rotate [DIAL] also selects a tone setting. No tone operation Subaudible tone encoder
Pocket beep
Tone squelch
DTCS beep
DTCS squelch
e Operate the transceiver in the normal way. r When the received signal includes a matching tone/code, the squelch opens and the signal can be heard. When the pocket beep function is activated, the transceiver also emits beep tones and blinks S.
When the received signals tone/code does not match, tone/ DTCS squelch does not open, however, the S-indicator shows signal strength. To open the squelch manually, push and hold [MONI](BAND).
Tone squelch (reverse)
DTCS squelch (reverse)
t Push [PTT] to answer or push and hold [MONI](BAND) for 1 sec. to stop the beeps and blinking.
10
OTHER FUNCTIONS
Tone scan
The transceiver can detect the subaudible tone frequency and DTCS code in a received signal. By monitoring a signal that is being transmitted on a repeater input frequency, you can determine the tone frequency required to access the repeater. q S et the desired frequency or memory channel to be checked for a tone frequency or DTCS code. w Push and hold [TONE](0) for 1 sec. repeatedly to activate the repeater tone, tone squelch or DTCS squelch. (T, T SQL or DTCS) e Push and hold [T.SCAN](#) for 1 sec. to start the tone scan.
To change the scanning direction, rotate [DIAL].
Tone scan for repeater tone
Tone scan for tone squelch
r When the tone frequency or DTCS code is decoded, the set mode contents are programmed with the frequency or code.
The tone scan pauses for the set period in scan pause timer (p. 47) when a tone frequency or DTCS code is detected. The decoded tone frequency is used for the repeater tone frequency when any tone setting, such as repeater tone or tone squelch is OFF. The decoded tone frequency is used for the tone squelch frequency when the tone squelch is ON. The decoded DTCS code is used for the DTCS squelch code when the DTCS squelch is ON.
Tone scan for DTCS squelch
t Push [V/M/C] to stop the scan.

If the scan is cancelled before the transceiver detects the tone or code, the set mode contents are not changed. T he detected tone is used for temporary operation only. The stored tone setting in memory or call channel wont be changed.
NOTE: Tone frequency is over-written automatically when it corresponds with the scanning tone frequency in tone squelch mode. However, it is not over-written in memory or call channel mode.
71
OTHER FUNCTIONS
10
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
72
Weather channel operation

There are 10 weather channels for monitoring weather broadcasts from the NOAA (National Oceanic and Atmospheric Administration).
U.S.A. version only
D Weather alert function

NOAA broadcast stations transmit weather alert tones before important weather announcements. When the weather alert function is turned ON, the selected weather channel is monitored every 5 seconds for the announcement. When the alert signal is detected, the ALT and the WX channel indications are displayed alternately and a beep sounds until the transceiver is operated. The previously selected (used) weather channel is checked periodically during standby or while scanning. q Select the desired weather channel. w Push [SET] to enter the Set mode. e Rotate [DIAL] to select the weather alert setting item, then rotate [VOL] to select On.
D Weather channel selection

q P ush [V/M/C] repeatedly to select weather channel mode.
The weather channel number appears.
w Rotate [DIAL] to select a desired weather channel. e Push [V/M/C] to return to the previous frequency or memory channel.
[DIAL] Weather channel dysplay
r Push [V/M/C] to return to the weather channel display.

WX appears.
ush and hold [SCAN](H/M/L) for 1 sec. activates the P weather channel scan. Push [SCAN](H/M/L) again to stop the scan.
Appears
10
OTHER FUNCTIONS
D Weather alert function (continued) t Set the desired stand-by condition.

Select the VFO mode, memory mode or call channel mode. Scan or priority watch operation can also be selected.
y When the alert is detected, a beep sounds and the following indication is displayed.
Shows above indications alternately.
u Turn the weather alert function OFF in the Set mode. OTE: While receiving a signal on a frequency other than N the Weather alert frequency, the receiving signal will be interrupted momentarily approximately every 5 seconds when the Whether alert function is ON. These interruptions cease when the Weather alert function is turned OFF.
73
OTHER FUNCTIONS
10
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
74
Cloning function
The IC-T70A/T70E has transceiver-to-transceiver data cloning capability. This function is useful when you want to copy all of the programmed contents from one IC-T70A/T70E to another. An optional OPC-474 CLONING CABLE is required. q Turn the transceivers power OFF, then connect an optional OPC-474 between both [SP] jacks.
OPC-474 to the [SP] jack to the [SP] jack
e Push [PTT] on the master transceiver.

CL Out m appears and the bar meter shows that cloning is taking place. After the cloning is completed, the display returns to CLOnE m.
r Push and hold [ ] for 1 sec. to turn power OFF.
The optional CS-T70 CLONING SOFTWARE is also available to clone/edit contents with a PC (for Microsoft Windows 2000/XP, Windows Vista or Windows 7) using ICF format files.
to the [SP] jack
OPC-478UC (USB type)
to USB port
w While continuing to push [V/M/C], push and hold [ ] for 1 sec. to enter the cloning mode.
CLOnE m appears.
OPC-478 to RS-232C (RS-232C type) port
PC
10
OTHER FUNCTIONS
Resetting
The display may occasionally display erroneous information (e.g. when first applying power). This may be caused externally by static electricity or by other factors. If this problem occurs, turn power OFF. After waiting a few seconds, turn power ON again. If the problem persists, perform either or both procedures below.
D All reset
q Push and hold [ ] for 1 sec. to turn power OFF. w W hile continuing to push [SET] , [BAND] and [H/M/L] , then turn power ON to reset the CPU.
CLEAR appears when resetting the CPU (See the illustration below).
D Partial reset
q Push and hold [ ] for 1 sec. to turn power OFF. w W hile continuing to push [H/M/L], then turn power ON to par tially reset the transceiver. NOTE: No message appears on the display after the partial reset is done. All reset
All reset
Reset the CPU before operating the transceiver for the first time, or if the internal CPU malfunctions due to static electricity, etc. All reset clears all programming and returns all settings to their factory defaults.
Partial reset
Use Partial reset if you want to initialize the operating conditions (VFO frequency, VFO settings, set mode contents) without clearing the memory contents. C AUTION: Resetting the CPU returns all programmed contents to their default settings. 75
Partial reset
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE SOLUTION
Charge the battery pack, or replace the batteries. Check the battery polarity. Clean battery terminals.
11
REF.
pp. 2, 1114 p. 11
If your transceiver seems to be malfunctioning, please check the following points before sending it to a service center.
Transceiver does not turn The battery is exhausted. ON. The battery polarity is reversed. L oose connection of a battery pack (case).
No sound comes from the Volume level is too low. Rotate [VOL] to adjust to a desired level. p. 16 speaker. An external speaker or a cloning cable is con- Check the external speaker connection or remove nected to the [SP] jack. the cloning cable. Transmitting is impossible. A frequency outside of the 144/440 MHz amateur bands is set. The PTT lock function is activated. The heat protection is activated, and Hot is displayed. Transmitting using the VOX The VOX gain is set to OFF or too low. function is impossible. T he microphone gain is too low. Set the frequency within 144/440 MHz amateur p. 20 bands. Set the PTT lock function OFF in the Initial set mode. p. 62 Cool down the transceiver. p. 23 S et the VOX gain to a suitable level. Set the microphone gain to a suitable level. p. 81 p. 58 p. 71
Contacting with another Different tone or code is used for the tone/ Check the tone/DTCS by performing a tone scan. station is impossible. DTCS squelch. Frequency cannot be set. The lock function is activated.
Push and hold [ ](SET) for 1 sec. to cancel the p. 21 lock function. The memory mode, Call channel mode, or Push [V/M/C] repeatedly to select the VFO mode. p. 18 weather channel mode is selected.
A program scan does not The memory mode, Call channel mode, or Push [V/M/C] repeatedly to select the VFO mode. p. 18 start. weather channel mode is selected. The same frequency has been programmed in P rogramming different frequencies in the scan edge p. 43 the scan edge channels, A and b. channels. A memory scan does not The VFO mode or Call channel mode is selected. Push [V/M/C] repeatedly to select the memory mode. p. 18 start. Only one or no memory channel has been pro- Program 2 or more memory channels. p. 31 grammed. The displayed frequency is The CPU has malfunctioned. erroneous. External factors have caused a fault. Reset the transceiver. Remove and re-attach the battery pack/case. p. 75 p. 2
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
76
12
D General
Version EUR, KOR UK, RSP U.S.A. TPE AUS CHN, EXP
SPECIFICATIONS
D Transmitter
: TX
144146, 430440 144146, 430440 144148, 420450*4 144146, 430432 144148, 420450*2 136174*3, 400479*2 (unit: MHz)
Frequency coverage
RX
144146, 430440 136174*1, 400479*2 136174*3, 400479*4 144146, 430432 136174*3, 400479*2 136174*3, 400479*2
Modulation system : Variable reactance freq. modulation Output power (at 7.2 V DC) : H igh 5.0 W, Mid. 2.5 W, Low 0.5 W (typical) Max. frequency deviation : 5.0 kHz (FM wide: approx.) 2.5 kHz (FM narrow: approx.) Spurious emissions : Less than 60 dBc at High/Mid. Less than 13 dBm at Low Ext. mic. impedance : 2.2 kW
*1Guaranteed 144146 MHz only, *2Guaranteed 430440 MHz only, *3Guaranteed 144148 MHz only, *4Guaranteed 440450 MHz only
Mode : FM, FM-N No. of memory channels : 302

(incl. 50 scan edges and 2 call channels)
D Receiver
Receive system : Double-conversion superheterodyne Intermediate frequencies : 1st 46.35 MHz, 2nd 450 kHz Sensitivity (except spurious points, 1 kHz/3.5 kHz Dev.; 12 dB SINAD) : Guaranteed freq. range Less than 0.18 V Other freq. range Less than 0.32 V Squelch Sensitivity (except spurious points, 1 kHz/3.5 kHz Dev.) : Guaranteed range Less than 0.18 V Other frequency range Less than 0.32 V Audio output power : (at 10% distortion/7.2 V DC) Internal speaker More than 700 mW with a 16 W load External speaker More than 400 mW with an 8 W load Selectivity : (at CH spacing 20 kHz/in the amateur bands) FM (Wide) More than 60 dB FM (Narrow) More than 60 dB Ext. speaker connector : 3-conductor 3.5(d) mm; (18)/8 W Spurious and image rejection ratio (in guaranteed freq. range) : More than 60 dB
Usable temp. range : 20C to +60C; 4F to +140F Tuning steps : 5 , 10, 12.5, 15, 20, 25, 30, 50, 100, 125 and 200 kHz Frequency stability : 2.5 ppm (20C to +60C; 4F to +140F) Power supply : 10.016.0 V DC for external DC power, or specied Icom battery pack Current drain (at 7.2 V DC) : TX High (typical) VHF 1.7 A, UHF 2.1 A Mid. (typical) VHF 1.2 A, UHF 1.5 A Low (typical) VHF 0.6 A, UHF 0.8 A Rx Max. output Less than 450 mA (Internal speaker) Less than 300 mA (External speaker) Power save Less than 40 mA (Duty 1:8) standby Less than 90 mA Antenna connector : SMA (50 W) Dimensions : 58(W)111(H)30(D) mm; (projections not included) 2932(W)438(H)1316(D) in Weight (approx.) : 380 g; 13.4 oz (with antenna and BP-264)
All stated specications are subject to change without notice or obligation.
77
OPTIONS
BP-263 BATTERY CASE Battery case for LR6 (AA) 6 alkaline batteries. BP-264 NI-MH BATTERY PACK 7.2 V/1400 mAh (Typ.) Ni-MH battery pack. Battery life: 11.5 hrs. (approx.; VHF, FM, high power, Tx : Rx : Standby = 5:5:90) Same as supplied one. (Not supplied with some version.) BP-265 LI-ION BATTERY PACK 7.4 V/1900 mAh (Min.)/2000 mAh (Typ.) Lithium Ion battery pack. Battery life: 16 hrs. (approx.; VHF, FM, high power, Tx : Rx : Standby = 5:5:90) BC-123S AC ADAPTER AC adapter for the desktop charger, BC-191 or BC-193. BC-147S AC ADAPTER AC adapter for the desktop charger, BC-192. BC-167S BATTERY CHARGER For regular charging of the Ni-MH battery pack, BP-264. Same as supplied one. (Not supplied with some version.) BC-191 DESKTOP CHARGER+BC-123S AC ADAPTER For rapid charging of the Ni-MH battery pack, BP-264. An AC adapter may be supplied with the charger, depending on the version. Charging time: Approx. 2 hours for the BP-264. BC-193 DESKTOP CHARGER+BC-123S AC ADAPTER For rapid charging of the Li-Ion battery pack, BP-265. An AC adapter may be supplied with the charger, depending on the version. Charging time: Approx. 2.5 hours for the BP-265. BC-191/BC-193 common specications Power supply voltage Charging temp. range
13
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
78
12 to 16 V DC or the specied Icom AC adapter (BC-123S) +10C to +40C; +50F to +104F
Dimensions 87.5(W)53.7(H)72.8(D) mm; (projections not included) 3716(W)218(H)278(D) in BC-192 DESKTOP CHARGER+BC-147S AC ADAPTER For regular charging of the Ni-MH battery pack, BP-264. An AC adapter may be supplied with the charger, depending on the version. Charging time: Approx. 16 hours for the BP-264. BC-192 specications Power supply voltage* Charging temp. range 12 to 16 V DC or the specied Icom AC adapter (BC-147S) 0C to +45C; 32F to +113F
Dimensions 87.5(W)53.7(H)72.8(D) mm; (projections not included) 3716(W)218(H)278(D) in

* Charging time differs depending on the input voltage. 12 V : Approx. 36 hours 13.8 V : Approx. 21 hours 16 V : Approx. 16 hours
13
OPTIONS
HS-94/HS-95/HS-97 HEADSET +OPC-2006 PLUG ADAPTER CABLE HS-94 : Ear hook type HS-95 : Neck & arm type HS-97 : Throat microphone OPC-2006 : Allows you to connect the HS-94/HS-95/HS-97 to the transceiver. After connecting, the VOX function can be used. SP-27 TUBE EARPHONE
Provides clear audio in noisy environments.
CP-12L CIGARETTE LIGHTER CABLE WITH NOISE FILTER CP-19R CIGARETTE LIGHTER CABLE WITH DC-DC CONVERTER Allows you to operate the transceiver through a 12 V cigarette lighter socket. You can also charge the attached battery pack (during stand-by only). CP-19R: A built-in DC-DC converter provides an 11 V DC output. CP-23L CIGARETTE LIGHTER CABLE Allows charging of the battery packs through a 12 V cigarette lighter socket. (For BC-191/BC-193) OPC-254L DC POWER CABLE For operation and charging via an external power supply. OPC-515L DC POWER CABLE Allows charging of the battery packs using a 12 V DC power source instead of the AC adapter. (For BC-191/ BC-192/BC-193) AD-92SMA ANTENNA CONNECTOR ADAPTER Allows you to connect an external antenna with a BNC connector. HM-131 SPEAKER-MICROPHONE Combination speaker-microphone that provides convenient operation while hanging the transceiver on your belt. HM-153 EARPHONE-MICROPHONE Ideal for hands-free operation: clip the HM-153 (with integrated PTT switch) to your lapel or breast pocket.
OPC-474 CLONING CABLE For transceiver-to-transceiver cloning. OPC-478/OPC-478UC CLONING CABLE Used for data cloning between transceiver and PC with CS-T70 (cloning software). CS-T70 CLONING SOFTWARE Provides quick and easy programming of such settings as memory channels and Set modes contents via your PCs RS-232C terminal (using OPC-478), or USB port (OPC478UC). Either OPC-478 or OPC-478UC is required. LC-174 CARRYING CASE Helps protect the transceiver from scratches, etc. Approved Icom optional equipment is designed for optimal performance when used with an Icom transceiver. Icom is not responsible for the destruction or damage to an Icom transceiver in the event the Icom transceiver is used with equipment that is not manufactured or approved by Icom.
79
OPTIONS
13
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
80
VOX function
The transceiver has a VOX function, which allows hands-free operation. An optional HS-94, HS-95 or HS-97 headset and the OPC-2006 plug adapter cable are also required for operation.
The VOX (voice operated transmission) function starts transmission when you speak into the microphone, without needing to push [PTT]; then, automatically returns to reception when you stop speaking.
D Turning the VOX function ON or OFF

q Connect an optional headset and plug adapter cable to the transceiver, and then turn the power ON. w Push [SET] to enter the Set mode. e Rotate [DIAL] to select the VOX setting item, then rotate [VOL] to select On.
D Optional unit connection

q Push and hold [ ] for 1 sec. to turn the power OFF. w Remove the jack cover. e Connect the optional HS-94, HS-95 or HS-97 and OPC2006, as illustrated below.
OPC-2006

VOX appears when the VOX function is ON.
HS-94
NOTE: W hen using the VOX function, adjust the microphone gain and the VOX-related settings (p. 81) to suit your operating environment (including your headset performance). Select the headset type between the HS-95 and other in the Initial set mode. (p.64) Set the microphone gain before setting the VOX gain in the Set mode (p. 58). We recommend setting the microphone gain to 3. W hen the PTT lock is set to On in the Set mode, you cannot transmit using the VOX function. (p. 62)
Transceiver
13
OPTIONS
D VOX-related settings
The VOX gain, the VOX delay, and the VOX time-out timer can be set in the Set mode. q Connect an optional headset and plug adapter cable to the transceiver, and then turn the power ON. w Push [SET] to enter the Set mode. e Rotate [DIAL] to select the VOX gain (VOX LV), the VOX delay (VOX.dLy), or the VOX time-out timer (VOX.tot) item. r Rotate [VOL] to select a desired option. t Push [V/M/C] to exit the Set mode. The VOX function does not activate transmission while in the Set mode.
VOX gain VOX delay
Sets the VOX delay to between 0.5 and 3.0 seconds (in 0.5 sec. steps). The VOX delay is the amount of time the transmitter stays ON after you stop speaking. (default: 0.5)
If VOX is intermittent, be sure the VOX delay is set long enough to allow normal pauses in speech, but keep the VOX ON until you nish speaking.
VOX time-out timer
The VOX gain level can be adjusted between 1 (minimum) and 10 (maximum), or turned OFF. Higher values make the VOX function more sensitive to your voice. (default: 5)
Sets the VOX time-out timer to between 1, 2, 3, 4, 5, 10 and 15 minutes to prevent accidental prolonged transmission for the VOX function. To turn the function OFF, select OFF. (default: 3)
While speaking into the headset microphone, adjust the VOX gain until VOX continuously appears on the LCD. CONVENIENT! While transmitting using the VOX function, you can adjust the VOX gain simply by rotating [DIAL]. 81
he VOX time-out timer must be set shorter than the timeT out timer, otherwise this timer will not be activated.
OPTIONS
13
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
82
Remote control function

The remote control unit allows you to remotely select operating frequencies, memory channels, etc. U ser remote control unit The illustrated circuit is for reference only.
to the [SP] jack
2.7k 6.8k 15k 33k
SIMPLE
S1 S2 S3 S4 Selects the Call channel. Turns the monitor function ON or OFF. Selects memory channel 0. Selects memory channel 1.
REMOTE 3.5(d) mm SP GND EXTERNAL SPEAKER 700 mW (8 ) Rated input >

+
NORM-1
S1 S2 S3 S4 Toggles the VFO mode and the memory mode. Selects the Call channel. Frequency or memory channel UP. Frequency or memory channel DOWN.
S1
S2
S3
S4
NORM-2
S1 S2 S3 S4 Toggles the VFO mode and the memory mode. Turns the monitor function ON or OFF. Frequency or memory channel UP. Frequency or memory channel DOWN.
B e sure to turn power OFF when plugging/unplugging the remote control unit to/from the [SP/MIC] jack.
D Simple remote control mode

q While continuing to push [SET], turn the power ON to enter the Initial set mode. w Rotate [DIAL] to select the microphone simple mode item. e Rotate [DIAL] to select SImPLE, nORm-1 or nORm-2 option.
he VFO mode cannot be selected via the remote control T unit when SIMPLE mode is selected. COMMON (SIMPLE/NORM-1/NORM-2)
S2 S3 S4 Transmits T-CALL (1750 Hz tone) while pushing [PTT]. Volume UP while operating the monitor function. Volume DOWN while operating the monitor function.
r Push [
] to return to the frequency display.
14
CE
IMPORTANT
When transmitting with a portable radio, hold the radio in a vertical position with its microphone 2.5 to 5 centimetres from your head and body. If you wear a portable two-way radio on your body, ensure that the antenna is at least 2.5 centimetres from your body when transmitting. C E Versions of the IC-T70E which display the CE symbol on the serial number label, comply with the essential requirements of the European Radio and Telecommunication Terminal Directive 1999/5/EC. This warning symbol indicates that this equipment operates in non-harmonised frequency bands and/or may be subject to licensing conditions in the country of use. Be sure to check that you have the correct version of this radio or the correct programming of this radio, to comply with national licensing requirements.
List of Country codes (ISO 3166-1)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Country Austria Belgium Bulgaria Croatia Czech Republic Cyprus Denmark Estonia Finland France Germany Greece Hungary Iceland Ireland Italy Latvia Codes AT BE BG HR CZ CY DK EE FI FR DE GR HU IS IE IT LV 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 Country Liechtenstein Lithuania Luxembourg Malta Netherlands Norway Poland Portugal Romania Slovakia Slovenia Spain Sweden Switzerland Turkey United Kingdom Codes LI LT LU MT NL NO PL PT RO SK SI ES SE CH TR GB
83
CE
14
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
84
DECLARATION OF CONFORMITY
We Icom Inc. Japan
1-1-32, Kamiminami, Hirano-ku Osaka 547-0003, Japan
Bad Soden 18th Dec. 2009
Declare on our sole responsibility that this equipment complies with the essential requirements of the Radio and Telecommunications Terminal Equipment Directive, 1999/5/EC, and that any applicable Essential Test Suite measurements have been performed. Kind of equipment: Type-designation: VHF/UHF DUAL BAND FM TRANSCEIVER
Place and date of issue
Icom (Europe) GmbH
iC- t70e
Communication Equipment Auf der Krautweide 24, 65812 Bad Soden am Taunus, Germany Authorized representative name
Version (where applicable): This compliance is based on conformity with the following harmonised standards, specifications or documents: i) EN 301 489-1 v1.6.1 (September 2005) ii) EN 301 489-15 v1.2.1 (August 2002) iii) EN 301 783-2 v1.1.1 (September 2000) iv) EN 60950-1 (2001): A11: 2004
Y. Furukawa General Manager
Signature
INDEX
1 1750 Hz tone28 A All reset75 Antenna2 Auto low power (AUTOLP)64 Auto power OFF (AP OFF)59 Auto repeater (AUTORP)60 Auto repeater function27 B Band scan (VFO mode)42 Battery caution10 Battery icons12 Battery information11 Battery life11 Battery pack2 Beep output level (BEEPLV)60 Belt clip1 Busy lockout (LK OUT)62 C Call channel mode18 Call channel watch49 Caution (for the optional BP-265 Li-Ion battery pack)9 Caution (for the supplied BP-264 Ni-MH battery pack)8 CE83 Channel number display36 Charging caution10 Charging note12, 13 Checking the repeater input signal25 Cloning function74 Copying call channel contents37 Copying memory contents37 D DC operating note15 Desktop battery chargers13 Dial speed acceleration (DIAL S)63 Display backlighting (LIGHT)60 Display type36 Display type (DISP M)64 DOC84 DTCS code (CODE)53 DTCS polarity (DTCS P) 53 DTCS squelch70 DTMF memory (DTMF)58 DTMF speed (DTMF-S)61 DTMF TX key (DTMF-T)58 Duplex operation26 E Entering and using the Initial set mode51 Entering and using the Set mode51 Erasing bank contents39 Explicit denitions i External DC power operation15
85
INDEX
F FCC information iii Features i Foreword i Frequency display36 Frequency offset (OFFSET)54 Frequency range and offset direction27 Front panel3 Full scan42 Function display6 G General description29 H Hand strap1 Headset selection (HS SEL)64 I Important i Index8588 Initial set mode item list52 Initial set mode items59 K Key lock function21 Keypad4 L LCD contrast (CONT)62 List of Country codes (ISO 3166-1)83 M Memory bank link function (B LINK)56 Memory bank scan45 Memory bank selection33 Memory bank setting32 Memory channel contents29 Memory channel programming31 Memory channel watch49 Memory clearing38 Memory mode18 Memory name (NAME)63 Memory scan 44 Memory scan watch49 Microphone gain (MIC G)58 Microphone simple mode (MIC S)59 Monitor function17 Monitor key action (MONI)63 O Off band indication25 Operating mode (MODE)54 Operating mode selection21 Optional battery case11 Optional unit connection80 Options7882
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
86
INDEX
P Partial reset75 Pocket beep68 Power OFF16 Power ON16 Power save (P SAVE)61 Precautionsii, iii Priority watch (PRIO)55 Priority watch operation49 Priority watch types48 Private channel display36 Program scan link function (P LINK)56 Program skip scan (P SKIP)55 Programmed scan 42 Programming a DTMF code sequence65 Programming bank name34 Programming memory name34 Programming scan name34 PTT lock (PTT LK)62 R Rapid charging with the BC-19113 Rapid charging with the BC-19314 Receiving22 Regular charging12 Regular charging with the BC-19214 Remote control function82 Repeater operation24 Repeater tone frequency (R TONE)53 Resetting75 Reverse duplex function (DUP.REV)54 Reverse tone/DTCS squelch68 Reverse duplex function26 S Scan edges programming43 Scan name (S NAME)63 Scan pause timer47 Scan pause timer (PAUSE)55 Scan resume setting47 Scan resume timer47 Scan resume timer (RESUME)55 Scan types40 Selecting a call channel29 Selecting a memory channel30 Selecting bank name indication35 Selecting memory name indication35 Selecting the mode18 Set mode item list52 Set mode items53 Setting audio volume16 Setting DTCS code for DTCS squelch69 Setting DTCS polarity69 Setting DTMF transfer speed67 Setting duplex direction26 Setting frequency offset26 Setting subaudible tone for tone squelch68 Setting the frequency using the dial19
87
INDEX
Setting the frequency using the keypad20 Setting the squelch level17 Setting the tuning step19 Side panel3 Skip channel setting46 Skip frequency setting46 Specications77 Squelch delay (SQL DL)62 Supplied accessories iv T Table of contentsv, vi Time-out timer (TOT)62 Tone and DTCS squelches68 Tone frequency and DTCS code68 Tone scan71 Tone squelch70 Top panel3 Transferring bank contents39 Transmit power selection22 Transmit warning23 Transmitting23 Transmitting a DTMF code sequence66 Troubleshooting76 TSQL frequency (C TONE)53 Tuning step (TS)54 Tuning step selection19 Turning the VOX function ON or OFF80 U Usable characters34 V VFO mode18 VFO scan watch50 Voltage indication (VOLT)61 VOX delay (VOX.DLY)59 VOX function80 VOX function (VOX)58 VOX gain (VOX LV)58 VOX time-out timer (VOXTOT)59 VOX-related settings81 W Weather alert (WX.ALT)54 Weather alert function72 Weather channel mode18 Weather channel operation72 Weather channel scan72 Weather channel selection72
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
88
#02 EUR
<Intended Country of Use> AT BE CY CZ DK EE FI FR DE GR HU IE IT LV LT LU MT NL PL PT SK SI ES SE GB IS LI NO CH BG RO TR HR
#03 UK
#12 RSP
A-6808H-1EX-q Printed in Japan 20092010 Icom Inc.

Printed on recycled paper with soy ink.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan

ICOM IC-T70A Instruction Manual

Uploaded by

Copyright:

Available Formats

ICOM IC-T70A Instruction Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ICOM IC-T70A Instruction Manual

Uploaded by

Copyright:

Available Formats

INSTRUCTION MANUAL

VHF/UHF DUAL BAND FM TRANSCEIVER

7  00 mW* AF power with BTL (bridge-tied load) amplier

SAVE THIS INSTRUCTION MANUAL This

NEVER connect the transceiver to a power source of more

R WARNING! NEVER hold the transceiver so that

DO NOT use or place the transceiver in direct sunlight

R WARNING! NEVER operate the transceiver with

DO NOT use harsh solvents such as benzine or alcohol to

R WARNING! NEVER operate the transceiver while

NEVER operate or touch the transceiver with wet hands.

CAUTION: Changes or modications to this device, not

Front, top and side panels

e CONTROL DIAL r VOLUME

t PTT SWITCH y EXTERNAL

PANEL DESCRIPTION D Keypad

m When the BP-263 is attached

Function display (continued)

Caution (for the optional BP-265 Li-Ion battery pack)

Optional battery case (BP-263)

OPC-254L (Optional) to 11 V DC (power supply) Black: _ White: +

Desktop battery chargers

D Rapid charging with the BC-191

Turn power OFF

BATTERY CHARGING D Regular chrging with the BC-192

D Rapid charging with the BC-193

Turn power OFF

Turn power OFF

External DC power operation

to cigarette lighter socket (12 V DC) CP-19R (Optional)

OPC-254L (Optional) BP-264 to 11 V DC (power supply) Black: _ White: +

Setting audio volume

Setting the squelch level

Two segments blink

Selecting the mode

D Call channel mode

D Weather channel mode*

Setting the tuning step

Setting the frequency

D Tuning step selection

Push [BAND] 440 MHz band

BASIC OPERATION D Using the keypad

Changing 10 MHz and below Editing 445.560 MHz to 432.380 MHz

Changing 1 MHz and below

Editing 145.500 MHz to 144.640 MHz

Operating mode selection

Key lock function

Transmit power selection

t  When a signal is received:

Middle power transmission

High power transmission

w  Push and hold [PTT] to transmit.

e  Speak into the microphone using your normal voice level.

r Release [PTT] to return to receive.

REPEATER AND DUPLEX OPERATIONS

r Push and hold [PTT] to transmit.

REPEATER AND DUPLEX OPERATIONS

D Checking the repeater input signal

D Off band indication

Blinks while pushing and holding [MONI]

7 00 mW* AF power with BTL (bridge-tied load) amplier

t When a signal is received:

w Push and hold [PTT] to transmit.

e Speak into the microphone using your normal voice level.

e Push [ ] to return to the frequency display. 27

w Rotate [DIAL] to select a desired call channel.

w Rotate [DIAL] to select a desired memory channel.

r Rotate [DIAL] to select a desired bank group from A to Z.

r Rotate [DIAL] to select the bank channel.

y Rotate [DIAL] to select a desired character.

Selecting memory/bank name indication

e Push [ ] to return to the frequency display.

e Push [SET] repeatedly to select bAnk.

y Push [S.MW](V/M/C) for 1 sec. to erase/transfer the bank contents.