Structural Steel Fire Guide

Structural Steel Fire Guide – Guide to the Use of Fire Protection Materials

Guide to the Use of Fire

Protection Materials

First Edition 2008

Author John Rakic

Level 13, 99 Mount Street, North Sydney. NSW 2060 Phone 9931 6666. Email [email protected] Website: www.steel.org.au
 Structural Steel Fire Guide –
Guide to the Use of Fire Protection Materials

by

John Rakic

First edition – 2008

 AUSTRALIAN STEEL INSTITUTE
(ABN/ACN (94) 000 973 839

Guide to the Use of Fire Protection Materials

Copyright © 2008 Australian Steel Institute

Published by: AUSTRALIAN STEEL INSTITUTE

All rights reserved. This book or any part thereof must not be reproduced in any form without the written
permission of Australian Steel Institute.

Note: Copyright of the information contained within this publication is held by Australian Steel Institute (ASI).
Written permission must be obtained from ASI for the use of any information contained herein which is
subsequently used in any commercially available software package.

FIRST EDITION 2008

National Library of Australia Cataloguing-in-Publication entry:

Rakic J (IRAK Consulting)

Structural Steel Fire Guide: 1st ed. – Guide to the use of fire protection materials/John Rakic ... [et al]

ISBN 978-1-921476-06-8 (pbk.)

Building, Fireproof.
Fire resistant materials.
Steel, Structural – Fires and fire prevention.
Other authors/contributors: Bennetts, Ian; Marinelli, Robert; Fergusson, Ben; Ng, Anthony; Beshara, Patrick;
Ryan, David.

Disclaimer: The information presented by J Rakic and the Australian Steel Institute in this publication has been
prepared for general information only and does not in any way constitute recommendations or professional
advice. While every effort has been made and all reasonable care taken to ensure the accuracy of the information
contained in this publication, this information should not be used or relied upon for any specific application
without investigation and verification as to its accuracy, suitability and applicability by a competent professional
person in this regard.
The Australian Steel Institute, its officers and employees and the authors and editors of this publication do not
give any warranties or make any representations in relation to the information provided herein and to the extent
permitted by law (a) will not be held liable or responsible in any way; and (b) expressly disclaims any liability or
responsibility for any loss or damage costs or expenses incurred in connection with this publication by any
person, whether that person is the purchaser of this publication or not. Without limitation, this includes loss,
damage, costs and expenses incurred as a result of the negligence of the authors, editors or publishers.
The information in this publication should not be relied upon as a substitute for independent due diligence,
professional or legal advice and in this regards the services of a competent professional person or persons should
be sought.

guide to the use of fire protection materials ii

 CONTENTS

Table of Contents ..................................................................................................... iii

Preface to 1st Edition ................................................................................................ iv
1. Introduction and Purpose............................................................................................ 1
2. Thermal response of steel ........................................................................................... 1
3. Determination of fire resistance levels (FRL) – process ..................................................... 2
4. Fire protection of steelwork ......................................................................................... 4
5. Conventional spray applied materials ............................................................................ 4
6. Board materials ........................................................................................................ 6
7. Thin film intumescent coatings .................................................................................... 7
8. Suppliers and installers of fire protection materials ........................................................ 10
9. Application of fire protection materials ........................................................................ 11
10. A guide to the different attributes of fire-protection materials ........................................... 12
11. Case studies .......................................................................................................... 13

This guide is an Australian Government funded initiative under the Industry Cooperative Innovation Program.

guide to the use of fire protection materials iii

 PREFACE TO THE 1st EDITION

This publication is designed to provide builders, architects and engineers with elementary details on
fire protective products based on the two general paths that designers may choose to follow:
1. ‘Deemed-to-Satisfy’ solution; or
2. A fire engineered solution.

The fire engineered option may offer a further 2 alternative options:

2a. Fire engineered solution for pricing and final design for construction; or
2b. Use of ‘Deemed-to-Satisfy’ for pricing and then a fire engineered solution for
final design for construction.

The guide will examine the steps required for these options and guidance on which products may be
most appropriate for certain scenarios.

John Rakic
Ian Bennetts
Robert Marinelli
Ben Fergusson
Anthony Ng
Patrick Beshara
David Ryan
July 2008

guide to the use of fire protection materials iv

1. INTRODUCTION AND PURPOSE

The performance-based building regulations in Australia and New Zealand principally relate to the safety
of occupants (including fire fighters) and the prevention of fire spread and damage to adjacent properties.

The performance requirements of the regulations may be met by following the ‘Deemed-to-Satisfy’
(DTS) approach or by designing an ‘Alternative Solution’, both referred to in the Building Code of
Australia ( BCA). The former approach is achieved by complying with all of the prescribed requirements
in relation to fire resistance of structural elements, sprinklers, hose reels, hydrants, detection, egress
requirements, smoke management and the like. These requirements vary depending on the building
classification (office, retail, residential, public, car park, etc) and the height and area of the building.
The Alternative Solution permits greater flexibility in architectural form and design and can permit
buildings that do not fit the type of building details upon which the DTS provisions were developed.

The design of an Alternative Solution must be undertaken by a professional fire safety engineer usually
in conjunction with a team which is likely to include at least the architect and/or owner’s representative,
the fire safety engineer, the building certifier and fire brigade representatives. This development of an
Alternative Solution is not a trivial process but can offer significant project savings including reduction
of required fire resistance for some elements. The fire engineered Alternative Solution can cover tenant
requirements over and above that of the BCA. This may cover consequential losses through loss of
use of the building and loss of building contents. It may also result in a more efficient building design
in accordance with client preferences.

The BCA requirements with respect to the fire-resistance level required for a particular situation will be
dictated by the Deemed-to-Satisfy provisions or the requirements of an Alternative Solution. In either
case the building certifier (building approval authority) must advise on the FRL required. It is therefore
not necessary for the builder or specifier to have a detailed understanding of the fire requirements of
the BCA. Therefore, a detailed description of the BCA requirements will not be covered in this document.

The purpose of this publication is to increase awareness of the fire-protection materials that
are now available for structural steel and to provide a list of major suppliers of fire-
protection materials. This publication does not specify thicknesses required to achieve
particular fire resistance levels. Manufacturers listed in this document can be approached
directly for this information.

2. THERMAL RESPONSE OF STEEL

A steel section absorbs heat through its surface and the greater the surface area exposed to fire the
more it will heat up. Conversely, the greater the mass of section the more it will act as a heat sink and
resist heating up. Thus the ratio surface area/mass (surface area-to-mass ratio) becomes a useful
measure of a steel member’s ability to resist temperature increase – the lower the number, the better
the resistance. In most cases, practical steel members do not have a sufficiently low exposed surface
area-to-mass ratio to provide a sufficient resistance to temperature rise and it is necessary to enhance
this performance by the addition of materials to the outside of the steel. These fire protection materials
both insulate and in some cases absorb energy.
The performance of a given thickness of fire protection when applied to a given steel member is
expressed in terms of a duration time of fire resistance. Thus if a particular combination of steel
member and protection thickness is stated as giving a fire resistance period of 95 minutes, this means
that if this member was tested under standard fire test conditions, it would support the load applied
to the member for at least 95 minutes. Standard fire test conditions are those experienced when the
member is tested in a standard test furnace in accordance with AS 1530.4 and requires the member
to be subjected to a prescribed time temperature curve known as the Standard Time Temperature
curve. This curve provides a relatively standardised approach to evaluating fire materials performance.

guide to the use of fire protection materials 1

Systematic testing of protected steel members results in a range of fire-resistance periods which are
used by manufacturers to determine material thicknesses to meet required fire-resistance levels (FRLs).
The thickness of fire protection required to achieve a given fire resistance is dependent on the thermal
properties of the fire protection material and the ratio of exposed surface area to mass. The higher this
ratio, the greater the thickness of protection required to achieve a particular fire resistance.
Given the beam or column size and the exposure condition (three sided or four sided exposure to the
fire) a supplier will provide the thickness required to achieve a fire resistance level.

Composite concrete floor slab

EXPOSURE TO FIRE ON 3 SIDES EXPOSURE TO FIRE ON 4 SIDES

Figure 1: Three sided and four sided exposure

3. DETERMINATION OF FIRE RESISTANCE LEVELS (FRL) – PROCESS INVOLVED

The attached flow chart demonstrates the regulatory process that is involved for a major project in
determining the required FRL for structural steel members. The chart covers two situations - the
adoption of the DTS requirements or the development of an Alternative Solution.
Paramount to the process of fire-safety engineering is the reliance on appropriately accredited and
registered persons. There are many bodies that accredit or register the professionals in the fire
engineering process. Each state legislation is different, however, Engineers Australia is one of the main
bodies that have a register of accredited / registered professionals in the fire engineering field.

guide to the use of fire protection materials 2

 Alternate Fire Design

Figure 2: Alternate Fire Design

FRL Determination

Deemed to Satisfy
Alternate Solution
BCA

Prescription FRLs Design FRLs

Determine Materials

Figure 3: FRL Determination

guide to the use of fire protection materials 3

4. FIRE PROTECTION OF STEELWORK

As noted in Section Two, the fire resistance of steel members is enhanced by the addition of fire protection
materials which insulate the surface. The type of fire protection material opted for will depend on a number
of factors such as:

• Cost and availability of selected fire protection materials and application.

• Location of the site – availability of type of material in relation to site.
• Aesthetic considerations – is the steel section to be visually expressed?
• Fire resistance to be achieved.

Note: Fire protection materials are not specifically designed for corrosion protection and advice on this
should be sought from the design engineer.

For the purpose of this publication, fire protection materials have been allocated into three distinct categories:

• Conventional spray applied materials.

• Fire resistant board materials.
• Thin film intumescent coatings (paints).

These categories and the relevant materials within are now considered in detail.

5. CONVENTIONAL SPRAY APPLIED MATERIALS

5.1 General

These are the oldest and at present the most widely used form of fire protection material in Australia.

They are relatively low density materials (at least when compared to concrete), which are typically supplied
in bags, mixed with water and sprayed as a type of slurry to the structural steel profiles requiring protection.

Application of spray applied materials is through specialist contractors using specialist equipment. This
process has a perception of being quite a messy process but with adequate masking and other on site
measures, control of overspray has proven to be more than possible and hence this process deemed
very popular.

Conventional spray applied materials are cost effective for large projects and if applied early in the
construction process prior to other trades being on site, further improvement in economies can be made.

guide to the use of fire protection materials 4

Figure 4: Application of conventional spray applied fire protection material

Figure 5: Conventional spray applied fire protection material

5.2 Available Materials

Supplier Product TM Composition

Promat Cafco 300 Premixed vermiculite plaster with other

chemical based materials

LAF Group Vermitex AF Gypsum-Vermiculite blend plus trace

chemical additives

Note: This table is not intended to be exhaustive and other suppliers and materials may be available.
1. Product is not suitable for external use
2. Surface preparation is to remove loose rust and grease

guide to the use of fire protection materials 5

6. BOARD MATERIALS

6.1 General

Fire resistant board materials, like conventional spray applied materials, have been used for a long
time in Australia. Board materials are cut to size and fixed around steel section, in essence ‘boxing’
them to provide the necessary fire-protection.
There are several proprietary board materials on the market and these are typically calcium silicate
based, vermiculite based, or gypsum based (plasterboard).
Application of board materials requires trained and approved applicators who are familiar with the
unique fixing requirements.

Figure 7 and 8: Steel sections clad in fire proofing board materials

guide to the use of fire protection materials 6

6.2 Available Materials

Supplier Product TM Composition

Boral Firestop Gypsum based board (plasterboard)

CSR Fyrchek Gypsum based board (plasterboard)

Fire Containment Maxilite Calcium Silcate

Firepro Spiralite Compressed mineral fibre

Lafarge Fireshield Gypsum based board (plasterboard)

Promat Promatect 100 Calcium Silcate

Promat Vermiculux Calcium Silcate

Note: This table is not intended to be exhaustive and other suppliers and materials may be available.
1. Plasterboard is suitable for internal use only
2. Other products may be suitable with external protective coatings
3. Firepro is recommended by the manufacturer as suitable for use in humid, wet
or cold climates

7. THIN FILM INTUMESCENT COATINGS

Thin film intumescent coatings, sometimes referred to as ‘intumescent paints’ are the most recent
form of fire-protection materials to be used in Australia. This form of technology has been significantly
improved and more suppliers have products available to the Australian market.

Figure 9: Intumescent char insulating layer after fire

Intumescent materials are those which expand to many times their original volume when heated
creating an insulation barrier and are widely used in other applications. Examples are intumescent fire
collars used for protection of plastic pipes or intumescent sealants used around steel pipes.
Intumescents are coatings which can be applied at relatively low thicknesses when compared to
conventional spray applied materials (e.g. 0.5 mm to 5mm dry thickness coating) and can be used to
allow expression of the steelwork from an architectural perspective. These materials have a much
higher viscosity compared with conventional paints and the application is required by specialist and

guide to the use of fire protection materials 7

approved contractors. The intumescent coating system may require preparation of the steel surface
by means of abrasion (e.g. a blasted finish) and application of a primer (or tie coat). The intumescent
paint material (known as the basecoat) is applied over the primer and in some cases a decorative
and/or protective top coat or top sealer coat may be applied for architectural reasons.

Products are proprietary and therefore the application and performance will vary by brand.

Proprietary formulations can behave differently under fire in the following ways:

• different degrees of stickability (some requiring proprietary primers for example)

• different degrees of expansion
• different thermal heat transfer coefficient of the char materials
• different thicknesses for protection of the same steel section
• different FRL capabilities
• different generic make up (solvent based, water based or epoxy based)

Intumescent coatings are engineered through chemistry for their intended use:
• External or internal
• Applied on site or applied off-site
• Low or high FRLs
• Low budget or premium quality product (pay for what you get)

Figure 10: Intumescent paint being applied in the field

guide to the use of fire protection materials 8

7.2 Available Materials (See Note 1.)

Supplier Product TM Composition Durability

Phoenix Phoenix 167 – Water borne Suitable for internal and

Fire Protection Hollow Sections external use with Phoenix
approved top coats

Phoenix Phoenix 168 – Water borne Suitable for internal and

Fire Protection One hour external use with Phoenix
approved top coats

Phoenix Phoenix 270 – Water borne Suitable for internal and

Fire Protection Two hour external use with Phoenix
approved top coats

International Interchar 963 Solvent based Suitable for internal and

Protective Coatings external use with
International approved
top coats

Firepro C608 Water borne Internal use only

Fireshield

PPG Industries Steelguard Solvent based Suitable for internal and

external use with
approved top coat

Promat Cafco WB3 Water borne Suitable for internal and

external use with
approved top coat

Resene Firetex M77 Solvent based Suitable for internal and

external use with
approved top coat

Note: This table is not intended to be exhaustive and other suppliers and materials may be available.
1. Grit blasting and priming is required as preparation for intumescent coatings

guide to the use of fire protection materials 9

8. SUPPLIERS AND INSTALLERS OF FIRE PROTECTION MATERIALS

Supplier Phone Web Site

Boral 02 8280 7133 www.boral.com.au

CSR 1800 621 117 www.gyprock.com.au

Exfoliators (PFP) Aust. 03 9706 6049 www.exfoliatorspfp.com.au

Fire Containment 1300 792 832 www.firecontainment.com.au

Firepro 02 9804 0262 www.firepro.com.au

International Protective Coatings 03 8336 8444 www.international-pc.com

Phoenix Fire Protection 1300 792 832 www.phoenixasia.com.au

PPG Industries 0407 722 744 www.ppgmc.com.au

Promat 1800 30 20 20 www.promat-ap.com

Resene 1800 738 383 www.resene.com.au

Trafalgar Building Products 02 9938 5499 www.trafalgarbp.com.au

The reader is also referred to the PFPA web site for a comprehensive list of local suppliers and
installers of fire-protection materials and product guidance.

Please contact the suppliers for performance data on their materials.

Relevant web sites are:
http://www.pfpa.com.au in the structural fire-protection dedicated area and specifically at
http://www.pfpa.com.au/product/steelfire protection.html

guide to the use of fire protection materials 10

9. APPLICATION OF FIRE-PROTECTION MATERIALS

9.1 On site application

Traditionally fire-protection materials have been applied on site to the as constructed steel structure.

This work is usually conducted by manufacturer approved and specialist contractors who have the
correct equipment and both training and experience with the fire protection materials typically used.

Figure 11: on site application

9.2 Off site application

With the advent of off site intumescent coatings, some fire-protection of structural steel is applied in
the steel fabrication yard, prior to delivery and erection on site. In the UK where FRLs of 60 minutes
are common, this has become the preferred means of fire protection but in Australia this practice is
limited at present since the Deemed to Satisfy provisions typically require steel members to achieve
an FRL of 90 minutes or greater. In most cases in this country an Alternative Solution to reduce the
FRLs to this level is required.

Figure 12 and 13: Photos of off site application

guide to the use of fire protection materials 11

10. A GUIDE TO THE DIFFERENT ATTRIBUTES OF FIRE-PROTECTION MATERIALS

The following table compares the attributes of the various generic fire protection materials.

Attribute Spray Board Intumescent Paints

Water Solvent Epoxy

based based based

1 Hr & 2 Hr Protection ✓ ✓ ✓ ✓ ✓
$/sqm Low High for Low Low High
beams

Apply On site ✓ ✓ ✓ ✓ ✓
Apply Off site ✗ ✗ ✓ ✓ ✓
Aesthetics Poor Average Paint-like Paint-like Rippled
Paint

Environmental ✓ ✓ ✓ Solvent ✓
issues

Impact resistant Poor Poor Good Good Excellent

guide to the use of fire protection materials 12

11. CASE STUDIES

a) Deemed to Satisfy
SCOTS CHURCH Kent St Sydney

Figure 14: Scots Church, Sydney CBD

guide to the use of fire protection materials 13

This Presbyterian Church located in the heart of Sydney was redeveloped as a site for residential
development by Westpoint Corporation. The new development extended from the Church at levels 6
to 12b and comprises contemporary two storey lofts. The building was protected by a combination of
fire sprayed material and fire rated plasterboard, a solution derived using the Deemed to Satisfy
provisions of the BCA.

1. Basement floor structure over car stacker excavation

This structure also supports the ground floor church stratum.
Structural steel trusses and beams were fire sprayed.

2. Existing Ground Floor to Level Five

The structure comprises steel framed columns and beams with in situ reinforced concrete
floor slabs and concrete encased floor beams. Columns were either concrete encased or
masonry clad.

Note: in areas where the ‘Deemed to Satisfy’, provisions were not applicable, fire engineer, De Fire,
assessed fire loads and determined the available cover was adequate.

3. New structure above Level 5

Transfer beams (Four in total transferring four columns ) at Level Six
These beams were conventionally fire sprayed because of their structural criticality.

Building columns (Steel)

External columns fire sprayed.
Internal columns achieved their rating by being located within fire isolating party walls.

Floor beams (Steel)

Perimeter beams were fire sprayed.
Primary beams and trusses like the columns are fire isolated between party walls.
Secondary internal beams being located within the ceiling were fire isolated. A number of
special case beams were fire sprayed due to their location.

guide to the use of fire protection materials 14

a) Alternative Solution
LATITUDE EAST at World Square Sydney – Fire Engineered

Figure 15 and 16: Latitude East, Sydney

This ten storey A-grade commercial building in the Sydney CBD was designed to sit atop an existing
retail complex. The first new level was built as a transfer deck and from level 13 the structure is
composite steel.

Fire engineering was conducted by Norman Disney & Young and supported by OneSteel.

The solution provided required only the primary beams and the main secondary beams joining
columns to be fire sprayed and only to an FRL of 60 minutes. The fire engineering solutions also
allowed the entire top two levels of the office floors to be completely unprotected steel floor beams.

guide to the use of fire protection materials 15

guide to the use of fire protection materials 16