S.

no DESCRIPTION Data For Approval

I Process Description
1 Item Description Caustic soda dosing pump
2 Tag No: P-713A/B
3 Model No PHL-90B
4 Type Hydraulic Diaphragm
5 Design code API 675
6 Location of installation Indoor
7 Humidity % Min. 50%, Max. 100%
8 Numbers Required 2(1W + 1S)
9 No of stages Single stage
10 Duty Continuous
II Operating Data
1 Fluid handled 10 - 12% NaOCL Solution
2 Type of fluid corrosive/ non corrosive etc Corrosive
3 Specific gravity of fluid 1.48 1
4 Rated Capacity LPH 2000
Max capacity upto which pump can be operated satisfactorily
5 2100
(LPH)
Min, capacity upto which pump can be operated satisfactorily
6 200
(LPH)
7 Discharge pressure Bar 6 Kg/sq.cm
8 Suction Flooded.
9 NPSH A Ample
10 Volumetric efficiency >85%
11 Mechanical efficiency >65%
12 BkW at Duty point 0.68
13 Motor Rating( at 50 Deg C) in KW 2.2KW (3HP)
13A Motor RPM 960 1
14 Plunger/Diaphragm speed (stoke/min) 120
15 Stroke Length 50MM
16 Operating temp. 22 - 35 °C
17 Specific gravity 1.48 At flow temp
18 Viscosity at operating temp. 1.30 Cp 1
19 pH 10.5 - 13.7
20 Starter type DOL
21 Maximum allowable particle size NA
22 Stoke Adjustment Manual & auto(0-100%)
Manual & auto(0-100%) by stroke adjustment (4-
23 Capacity control
20 ma signal from DCS)
24 Guaranteed Noise level(dba) db <85 from one meter distance
25 Set Pressure of Relief Valve 6.5kg/cm2
26 Gear Box Ratio 8:01
27 Coupling Lov Joy Coupling
28 Type of Bearing Tapper Roller & Ball Bearing
29 Design life of Bearing 15000 Hours Approx
30 Minimum differential pressure required (Bar) 1 Bar
31 Type of Lubrication Hydrol 150
Design life of Pump shall be Minimum service life 20 years &
32 Confirmed
3years for uninterupted operation of pump
III Flange
1 Suction end Location Bottom
2 Discharge end location Top
3 a.) Suction 1 1/2'' ANSI B16.5, #150, FF
4 b.) Discharge 1 1/2'' ANSI B16.5, #150, FF
IV Material of construction
1 Liquid end PP
2 Hydraulic Diaphragm PTFE Faced nitrile
3 Plunger CI IS 210 FG 220 -Rev-A 1
Doc. No. P135-D0003-072_R0
1 of 2
 1
4 Diameter of plunger(mm) NA
5 Valve PVC
6 Valve Body PVC
7 Valve seat PVC
8 Flange PVC
9 Base Plate MS as Per IS 2062, Gr.A (Epoxy coated)
V Scope of supply of accessories
Motor as per electrical specification,enclosed in chapter 4 of
1 yes (Supplied by VA Tech - IDE)
volume II B. 1
2 Base frame yes
3 Coupling yes
4 Speed reducer yes
5 Gear box yes
5 Foundation bolt yes
6 Internal relief valve( Inbuilt) yes
7 Coupling Guard yes
8 Suction filter( Y Strainer) yes
VI Note:
1 Confirmed
Painting wherever applicable shall be done as'per the
enclosed painting specification, chapter 7 of the volume II A
2 Respective Motor data sheet / documents number P135-E0003-
3 The companion flanges, gaskets, fasteners, expanders/ Confirmed
reducers, to match the pipe size shall be supplied by
VATECH. MOC shall be as per contract specification
4 Motor shall be supplied by VA TECH paralley while supplying Confirmed
the pump
5 Commissioning spares shall be supplied with pumps Confirmed
VII Documents Enclosed
1 Equipment GA drawing 2025SP-GA-PHL-90PP-ECC-001_Rev.B
2 Cross sectional drawing 2025SP-CS-PHL-90-PP-ECC-001_Rev.B
3 Pulsation Dampener Drawing PDA-10LT-PVC-001_Rev.B
4 ECC - Drive assembly CS-PHL-ECC-001_Rev.A
5 Performance curve Annexure - A

Doc. No. P135-D0003-072_R0

2 of 2