Taro

150 mm BOREWELL SUBMERSIBLE PUMPSET

PERFORMANCE CHART

TEXMO INDUSTRIES Since 1956

 2
GENERAL INFORMATION
PERFORMANCE RELATED SPECIFICATIONS
Ÿ Recommended voltage range : Single Phase Three Phase
(At motor terminal) 180 - 240 V 350 - 440 V
150 - 200 V (L-Series) 250 - 380 V (L-Series)

Ÿ Electric power supply : 415 / 220 V, 50 Hz, AC power supply

Ÿ Connection : Group DOL SD

BWS Up to 7.5 HP 7.5 HP & above

Ÿ Suitable overload relay for three phase and MCB for single phase products are to be provided as an electrical safety measure for the
machine.
Ÿ Advisable to operate in the pump set in the recommended range for trouble free operation and to ensure a long life.

Ÿ Time interval between subsequent starts : 5 minutes (minimum)

Ÿ Pump sets are suitable for pumping clear, cold, non-aggressive water without any abrasive solid particles with the following
characteristics
Temperature : 330C Maximum
Allowable sand content : 50 mg / lit Maximum
Total Dissolved Solids : 3000 mg / lit Maximum
Hardness : 300 Maximum
pH value : 6.5 - 8.5
Direction of rotation : Anti clockwise when viewed from the delivery side of the pump

Others
Ÿ Performance values given are subject to change in accordance with prevailing voltage and frequency conditions.

Ÿ Head values given in the performance charts are exclusive of pipe friction and fitting losses. These losses need to be taken into account
while calculating the actual total head before selecting a suitable pump set.
Ÿ In view of continuous improvements on existing products, information and performance values given in the catalogue are subject to
change without notice.

Note : Shaded figures in the chart indicate the recommended operating range.
 3
PUMP SELECTION
Irrigation wells and pumps are costly installations, which require efficient utilization. A major part of the energy used in agriculture is in
pumping water. Hence efficient utilization of the limited energy resources calls for the selection of the most suitable pump, keeping in view
the requirements of irrigation, characteristics of the well / water source, kind of power available, economic conditions of the farmer and
other factors. It is a process of matching of well and pump characteristics for optimum water output.

CRITERIA FOR SELECTION

The main factors influencing the selection of pumping sets are :
i. Peak water requirement
ii. Yield of well or water source
iii. Availability of energy

WATER REQUIREMENT, V IN L/D

It is the maximum quantity of water required in litres / day to meet out the daily crop water requirement and pumping rate in l/s is calculated
by V / (T x 3600) where, T – Average pumping hours.

Relevant Details
1. Daily crop water requirement in litres or cm for different stages
2. Cropped area in m2 (m2 x cm x 10 will give water requirement in litres)

YIELD OF WELL OR WATER SOURCE, Y IN L/S

It is the recuperation rate at which water recharges into the well and it is the maximum rate at which water can be pumped out under steady
draw down conditions. This can be assessed directly from pump testing results or converted from inch to lit./s referring to discharge table.

Relevant Details
1. Type of water source (Open well / Borewell / River / Sump)
2. Size of Borewell
3. Static water level below ground level (Water level when pump is switched off)
4. Dynamic water level below ground level (Expected level when pump is switched on)
5. Expected maximum low water level during summer
6. Proposed pump set erection depth
7. Existing / proposed pipe details (Sizes and lengths)
8. Vertical elevation from water source to discharge point
9. Number of fittings like (Tee, Bends, Valves etc.,)

ENERGY AVAILABLE, HP
It is the quantitative and qualitative data on the power available for pumping out the water from the water source. This includes phase,
sanctioned HP, frequency, voltage fluctuation and three and two phase power supply and time of which power in available.

Relevant Details
1. Main line to starter distance
2. Starter to pump set distance
 4
Selection Procedure
Step 1 - Discharge calculation, Q
V – Maximum crop water requirement in litres, D in case of irrigation depth in cm for peak demand of water for the selected
cropping pattern
A – Cropped area in m2
T – Allowed water filling time or pumping time in sec (considering power availability hrs)
Required pumping rate, Q = V / T or (D x A x 10) / T
[In case of trying out maximum possible discharge, Q is to be assumed]

Step 2 – Comparison of discharge, Q with yield, Y

As indicated earlier, discharge rate has to be limited to 80% of the safe yield for trouble free performance and better pump life avoiding any
dry running

Step 3 – Selection of pump size or series

Based on the calculated discharge rate, Q the suitable pump size is to be selected. In case of borewell submersibles, suitable pump series is
to be selected considering borewell size also.

Step 4 – Total head calculation, H

Suction head, Hs
Ds – Size of suction pipe in mm
Ls – Length of suction pipe in m including equivalent length of pipe for the fittings
Vs – Vertical distance of pump set from working water level in m
Refer to pipe friction loss chart or table and read friction value, Fs% in m / 100 m length of suction pipe against discharge, Q and existing or
selected pipe size, Ds.
Pipe friction in suction pipe, Fs = (Ls x Fs%) / 100
Suction head, Hs = Vs + Fs
Note: For Submersible pump sets the suction head value is zero

Delivery head, Hd
Dd – Size of delivery pipe in mm
Ld – Length of delivery pipe in m including equivalent length of pipe for the fittings
Vd – Vertical distance of discharge point from pump set level in m including ground elevation
Refer to pipe friction loss chart or table and read friction value, Fd% in m per 100 m length of delivery pipe, against discharge, Q and existing
or selected pipe size, Dd.
Pipe friction in delivery pipe, Fd = (Ld x Fd%) / 100
Delivery head, Hd = Vd + Fd

Step 5 – Total head

Total head, H = Hs + Hd + Hf + He
Hf – Fitting loss in the entire pipeline system (Refer to fitting loss table)
He – Exit pressure head at discharge point as required
 5
Step 6 – Energy requirement
Approx. energy requirement, HP = (Q x H) / (75 x Ep)
Ep – Pump efficiency value in fraction, which varies with product HP and pipe size
Select an appropriate pump model or stage for the given total head, H and discharge, Q referring to the product performance chart. Best
efficiency point (declared duty point) is always preferred. If the HP of the selected pump model is less than the sanctioned HP, then we may
proceed with the same. If not, assumed or calculated Q has to be reduced and above steps are to be repeated.
In case of borewell submersible pump sets, correct product series is to be decided based on the required pumping rate Q before selecting a
suitable pump model and number of stages.

SELECTION OF PUMPS FOR PARALLEL CONNECTIONS

Requirement of parallel connections arises when the required discharge rate is not met with the available pump models. In this case two or
more pumps with almost matching pressure head should be selected. Following factors are to be considered for parallel operations.
a. Pumps of similar head characteristics are to be selected
b. No pump should operate at its shut off head or above maximum permissible head
c. No pump should operate below recommended head range as this leads to cavitation

SELECTION OF PUMPS FOR SERIES CONNECTIONS

Requirement of series connections arises when the required total head is not met with the available pump models. In this case two or more
pumps with almost matching discharge rate should be selected. Series installations of pumps are to be spaced in such a way that neither the
pump gets overloaded or ends up with discharge cavitation.

OTHER FACTORS AFFECTING THE PUMP PERFORMANCE (after installation)

1. Suction head variation
2. Dynamic water level i.e., draw down variation
3. Condition of existing pipe line including inner roughness / amount of sedimentation and the life
4. Recharge rate of water source
5. Frequency and voltage conditions

Cable selection
Va – Actual voltage available in the field (Volts)
Vr – Rated voltage of the motor (Volts)
La – Actual cable length from starter to motor terminal (metre)
HP – Power of the selected motor
I – Full load current of the selected motor [For SD motors, it is 1 /Ö3 times the FL current] (Amperes)
Lc – Calculated equivalent cable length (Vr x La) / Va (metre)

Refer to cable selection chart and select appropriate cable size for the given I and Lc values.

Follow the same procedure for selecting suitable wire / cable size for mail line to starter.
6
150 mm Borewell Submersibles (TRS / TRS-L)

PRODUCT FEATURES
Ÿ Available in radial flow impeller designs. Ÿ Built in NRV with minimum friction.
Ÿ High quality dynamically balanced LTB impellers. Ÿ Stainless steel stator shell to prevent rust formation.
Ÿ Specially designed carbon thrust bearing.
Ÿ Special LTB and nitrile rubber bearing bushes for high wear
resistance and longer life. Ÿ High quality seal rings and sand guards to protect motor from
sand entry.
Ÿ Diffusers of gunmetal and housings of high grade cast iron to Ÿ High quality water-resistant polymer insulated wires for
ensure long life. longer life even under adverse voltage conditions.
Ÿ Easily rewindable Squirrel cage motor of water-cooled,designed Ÿ Pressure diaphragm to compensate excess pressure due to
for 350 - 440 V, (TRS) 280-380V (TRS-L) 50 Hz, AC power heating up of filled water.
supply.

MATERIAL OF CONSTRUCTION
Part Name Material Part Name Material
Impeller LTB-2 Motor body AISI 304
Diffuser Gunmetal Bearing housing CI FG 200
Pump shaft AISI 410 / 431 Motor shaft 55C8 / AISI 431
Sleeve AISI 410 Journal bush LTB-4 / Carbon
Bearing bush NBR Thrust bearing AISI 420 / Carbon
Non return valve AISI 304 / NBR Winding wire Polywrapped copper

APPLICATIONS
Domestic and community water supply | Water supply to high rise buildings, housing complexes, bungalows and industries | Cattle and poultry
farms | Irrigation of farms | Dairies | Cooling water circulating systems | Fire fighting systems | Fountains
 7
PERFORMANCE CHART
TARO "TRS 30 SERIES" - THREE PHASE RADIAL FLOW SUBMERSIBLE PUMPSETS FOR 150 mm (6”) BOREWELLS
Approximate performance values of TRS 30 series at 415 V (-15% to +6%), 2880 rpm, 50 Hz AC power supply
CAPACITY
Motor

Pipe Size (mm)

FL Current (A)
Model Name Gpm 0.0 9.2 13.2 19.8 23.8 29.0 33.0 37.0
Connection

Rating

Stages
l/m 0.0 42.0 60.0 90.0 108.0 132.0 150.0 168
3
M /hr 0.0 2.5 3.6 5.4 6.5 7.9 9.0 10.1
Pump Motor kW HP
l/s 0.0 0.7 1.0 1.5 1.8 2.2 2.5 2.8

TRS 3009 @ TS 022 DOL 2.2 3 9 86.4 81.0 78.3 72.4 67.5 60.1 52.9 43.9 6.5

TRS 3015 F TS 037 DOL 3.7 5 15 144.0 135.0 130.5 120.6 112.5 100.2 88.2 73.2 10.0
HEAD VALUES IN METRES
TRS 3015 Q J TS 037 DOL 3.7 5 15 144.0 135.0 130.5 120.6 112.5 100.2 88.2 73.2 10.0

TRS 3018 Q TS 045 DOL 4.5 6 18 172.8 162.0 156.6 144.7 135.0 120.2 105.8 87.8 12.0
40
TRS 3020 F TS056 DOL 5.5 7.5 20 192.0 180.0 174.0 160.8 150.0 133.6 117.6 97.6 14.5

TRS 3020 Q TS056 DOL 5.5 7.5 20 192.0 180.0 174.0 160.8 150.0 133.6 117.6 97.6 14.5

TRS 3023 Q TS056 DOL 5.5 7.5 23 220.8 207.0 200.1 184.9 172.5 153.6 135.2 112.2 14.5

TRS 3030 Q TS 075 SD 7.5 10 30 288.0 270.0 261.0 241.2 225.0 200.4 176.4 146.4 19.5

TARO "TRS 30 SERIES" - SINGLE PHASE RADIAL FLOW SUBMERSIBLE PUMPSETS FOR 150 mm (6”) BOREWELLS
Approximate performance values of TRS 30 series at 220 V (-15% to +6%), 2880 rpm, 50 Hz AC power supply
CAPACITY
Motor
Pipe Size (mm)

FL Current (A)
Model Name Gpm 0.0 9.2 13.2 19.8 23.8 29.0 33.0 37.0
Connection

Rating
Stages

l/m 0.0 42.0 60.0 90.0 108.0 132.0 150.0 168

3
M /hr 0.0 2.5 3.6 5.4 6.5 7.9 9.0 10.1
Pump Motor kW HP
l/s 0.0 0.7 1.0 1.5 1.8 2.2 2.5 2.8
HEAD VALUES
TRS 3022 SS056 DOL 5.5 7.5 22 40 IN METRES
211.2 198.0 191.4 176.9 165.0 147.0 129.4 107.4 40.0

Performance confirming to IS : 8034 and 9283 DOL - Direct On Line S D - Star Delta Maximum outer diameter : 142 mm
'F series' is available in 50mm delivery - Star rated pumpsets Q - SS Tie bar J - Against batch order
Note : All 6” motors are ISI marked @ - Series also available in 50mm delivery

PRODUCT TYPE KEY

T R S 30 15 - Taro Radial flow Six inch 30 series 15 Stages T S 037 - Three phase, Six inch motor (037 - Power code)
 8
PERFORMANCE CHART
TARO "TRS 40 SERIES" - THREE PHASE RADIAL FLOW SUBMERSIBLE PUMPSETS FOR 150 mm (6”) BOREWELLS
Approximate performance values of TRS 40 series at 415 V (-15% to +6%), 2880 rpm, 50 Hz AC power supply
CAPACITY
Motor

Pipe Size (mm)

FL Current (A)
Model Name Gpm 0.0 15.8 19.8 23.8 29.0 33.0 35.6 39.6 43.6 46.2 52.8
Connection

Rating

Stages
l/m 0.0 72 90 108 132.0 150.0 162 180.0 198.0 210.0 240
3
M /hr 0.0 4.3 5.4 6.5 7.9 9.0 9.7 10.8 11.9 12.6 14.4
Pump Motor kW HP
l/s 0.0 1.2 1.5 1.8 2.2 2.5 2.7 3.0 3.3 3.5 4.0

TRS 4010 A TS 037 DOL 3.7 5 10 94.0 92.0 90.3 87.0 82.3 78.3 75.0 71.3 66.5 62.0 52.5 10.0

TRS 4012 TS 045 DOL 4.5 6 12 112.8 110.4 108.3 104.4 98.7 93.9 90.0 85.5 79.8 74.4 63.0 12.0

TRS 4015 TS 056 DOL 5.5 7.5 15 141.0 138.0 135.4 130.5 123.4 117.4 112.5 106.9 99.8 93.0 78.8 14.5
HEAD VALUES IN METRES

TRS 4015 Q TS 056 DOL/SD 5.5 7.5 15 141.0 138.0 135.4 130.5 123.4 117.4 112.5 106.9 99.8 93.0 78.8 14.5

TRS 4020 TS 075 SD 7.5 10 20 50 188.0 184.0 180.5 174.0 164.5 156.5 150.0 142.5 133.0 124.0 105.0 19.5

TRS 4025 TS 093 SD 9.3 12.5 25 235.0 230.0 225.6 217.5 205.6 195.6 187.5 178.1 166.3 155.0 131.3 25.0

TRS 4030 TS112 SD 11.0 15 30 282.0 276.0 270.8 261.0 246.8 234.8 225.0 213.8 199.5 186.0 157.5 29.0

TRS 4036 TS 130H SD 13 17.5 36 338.4 331.2 324.9 313.2 296.1 281.7 270.0 256.5 239.4 223.2 189.0 34.0

TRS 4040 TS 150H SD 15 20 40 376.0 368.0 361.0 348.0 329.0 313.0 300.0 285.0 266.0 248.0 210.0 39.0

TARO "TRS 40 UH SERIES" - SINGLE PHASE RADIAL FLOW SUBMERSIBLE PUMPSETS FOR 150 mm (6”) BOREWELLS
Approximate performance values of TRS 40 series at 415 V (-15% to +6%), 2880 rpm, 50 Hz AC power supply
CAPACITY
Motor
Pipe Size (mm)

FL Current (A)
Model Name Gpm 0.0 6.6 13.2 19.8 26.4 29.0 33.0 35.6 39.6 43.6 46.2 52.8 59.4 66.0
Connection

Rating
Stages

l/m 0.0 30 60 90 120 132 150 162 180 198 210 240 270 300

M3/hr 0.0 1.8 3.6 5.4 7.2 7.9 9.0 9.7 10.8 11.9 12.6 14.4 16.2 18.0
Pump Motor kW HP
l/s 0.0 0.5 1.0 1.5 2.0 2.2 2.5 2.7 3.0 3.3 3.5 4.0 4.5 5.0

TRS 4006 UH TS 037 DOL 3.7 5 6 102 100 97.7 94.1 88.3 85.5 80.7 77.3 72.0 66.5 62.7 52.7 40.9 26.5 10.0

TRS 4007 UH TS 045 DOL 4.5 6 7 119 117 114 110 103 99.8 94.2 90.2 84.0 77.6 73.2 61.4 47.8 30.9 12.0
HEAD VALUES IN METRES

TRS 4010 UH TS 056 DOL/SD 5.5 7.5 10 169 167 163 157 147 143 135 129 120 111 105 87.8 68.2 44.2 14.5

TRS 4012 UH TS 075 SD 7.5 10 12 203 200 195 188 177 171 161 155 144 133 125 105 81.9 53.0 19.5
50
TRS 4015 UH TS 093 SD 9.3 12.5 15 254 250 244 235 221 214 202 193 180 166 157 132 102 66.3 25.0

TRS 4018 UH TS 112 SD 11.0 15 18 305 300 293 282 265 257 242 232 216 199 188 158 123 79.5 29.0

TRS 4021 UH TS 130H SD 13.0 17.5 21 356 350 342 329 309 299 283 271 252 233 219 184 143 92.8 34.0

TRS 4024 UH TS 150H SD 15.0 20 24 407 400 391 376 353 342 323 309 288 266 251 211 164 106 39.0

Performance confirming to IS : 8034 and 9283 D O L - Direct On Line S D - Star Delta Maximum outer diameter : 142 mm
Note : All 6” motors are ISI marked - Star rated pumpsets Q - SS Tie bar A - Single phase also available

PRODUCT TYPE KEY

T R S 40 10 - Taro Radial flow Six inch 40 series 10 Stages T S 037 - Three phase, Six inch motor (037 - Power code)
T R S 40 20 - Taro Radial flow Six inch 40 series 20 Stages T S 075 - Three phase, Six inch motor (075 - Power code)
T R S 40 12 UH - Taro Radial flow Six inch 40 series 12 Stages, Ultra Head T S 075 - Three phase, Six inch motor (075 - Power code)
 9
PERFORMANCE CHART
TARO "TRS 43 SERIES" - THREE PHASE RADIAL FLOW SUBMERSIBLE PUMPSETS FOR 150 mm (6”) BOREWELLS
Approximate performance values of TRS 43 series at 415 V (-15% to +6%), 2880 rpm, 50 Hz AC power supply
CAPACITY
Motor

Pipe Size (mm)

FL Current (A)
Model Name Gpm 0.0 23.8 29.0 33.0 35.6 39.6 42.9 46.2 52.8 55.4 59.4
Connection

Rating

Stages
l/m 0.0 108 132 150 162.0 180.0 195.0 210.0 240.0 252 270
3
M /hr 0.0 6.5 7.9 9.0 9.7 10.8 11.7 12.6 14.4 15.1 16.2
Pump Motor kW HP
l/s 0.0 1.8 2.2 2.5 2.7 3.0 3.3 3.5 4.0 4.2 4.5

TRS 4310 J TS 045 DOL 4.5 6 10 102.0 97.3 96.0 94.0 91.0 85.7 80.0 73.7 62.0 57.0 49.3 12

TRS 4312 TS 056 DOL 5.5 7.5 12 122.4 116.8 115.2 112.8 109.2 102.8 96.0 88.4 74.4 68.4 59.2 14.5

TRS 4312 J TS 056 SD 5.5 7.5 12 122.4 116.8 115.2 112.8 109.2 102.8 96.0 88.4 74.4 68.4 59.2 14.5
HEAD VALUES IN METRES

TRS 4313 TS 056 DOL 5.5 7.5 13 132.6 126.5 124.8 122.2 118.3 111.4 104.0 95.8 80.6 74.1 64.1 14.5

TRS 4316 TS 075 SD 7.5 10 16 163.2 155.7 153.6 150.4 145.6 137.1 128.0 117.9 99.2 91.2 78.9 19.5
50
TRS 4320 © TS 093 SD 9.3 12.5 20 204.0 194.7 192.0 188.0 182.0 171.3 160.0 147.3 124.0 114.0 98.7 25

TRS 4325 © TS 112 SD 11 15 25 255.0 243.3 240.0 235.0 227.5 214.2 200.0 184.2 155.0 142.5 123.3 29

TRS 4330 © TS 130 SD 13 17.5 30 306.0 292.0 288.0 282.0 273.0 257.0 240.0 221.0 186.0 171.0 148.0 34

TRS 4330 TS 150 SD 15 20 30 306.0 292.0 288.0 282.0 273.0 257.0 240.0 221.0 186.0 171.0 148.0 39

TRS 4332 J TS 150H SD 15 20 32 326.4 311.5 307.2 300.8 291.2 274.1 256.0 235.7 198.4 182.4 157.9 39

TARO "TRS 43 SERIES" - SINGLE PHASE RADIAL FLOW SUBMERSIBLE PUMPSETS FOR 150 mm (6”) BOREWELLS
Approximate performance values of TRS 43 series at 220 V (-15% to +6%), 2880 rpm, 50 Hz AC power supply
CAPACITY
Motor
Pipe Size (mm)

FL Current (A)
Model Name Gpm 0.0 23.8 29.0 33.0 35.6 39.6 42.9 46.2 52.8 55.4 59.4
Connection

Rating
Stages

l/m 0.0 108 132 150 162.0 180.0 195.0 210.0 240.0 252 270
3
M /hr 0.0 6.5 7.9 9.0 9.7 10.8 11.7 12.6 14.4 15.1 16.2
Pump Motor kW HP
l/s 0.0 1.8 2.2 2.5 2.7 3.0 3.3 3.5 4.0 4.2 4.5
HEAD
TRS 4308 SS 037 DOL 3.7 5 8 50 VALUES
IN METRES
81.6 77.9 76.8 75.2 72.8 68.5 64.0 58.9 49.6 45.6 39.5 28

Performance confirming to IS : 8034 and 9283 D O L - Direct On Line S D - Star Delta Maximum outer diameter : 142 mm
- Star rated pumpsets J - Against batch order © - ISI marked sets
Note : All 6” motors are ISI marked

PRODUCT TYPE KEY

T R S 43 08 - Taro Radial flow Six inch 43 series 08 Stages T S 037 - Three phase, Six inch motor (037 - Power code)
T R S 43 12 - Taro Radial flow Six inch 43 series 12 Stages T S 056 - Three phase, Six inch motor (056 - Power code)
 10
PERFORMANCE CHART
TARO "TRS 45 / 45 UH SERIES" - THREE PHASE RADIAL FLOW SUBMERSIBLE PUMPSETS FOR 150 mm (6”) BOREWELLS
Approximate performance values of TRS 45 / 45 UH series at 415 V (-15% to +6%), 2880 rpm, 50 Hz AC power supply

CAPACITY
Motor

Pipe Size (mm)

FL Current (A)
Model Name Gpm 0.0 29.0 33.0 39.6 46.2 52.8 59.4 66.0 72.6
Connection

Rating

Stages
l/m 0.0 132 150 180 210 240 270 300 330
3
M /hr 0.0 7.9 9.0 10.8 12.6 14.4 16.2 18.0 19.8
Pump Motor kW HP
l/s 0.0 2.2 2.5 3.0 3.5 4.0 4.5 5.0 5.5

TRS 4507 TS 037 DOL 3.7 5 7 81.2 68.6 67.2 63.7 59.5 56.0 50.4 44.1 37.1 10.0

TRS 4508 S © TS 037 DOL 3.7 5 8 92.8 78.4 76.8 72.8 68.0 64.0 57.6 50.4 42.4 10.0

TRS 4510 © TS 056 DOL/SD 5.5 7.5 10 116.0 98.0 96.0 91.0 85.0 80.0 72.0 63.0 53.0 14.5

TRS 4513 © TS 075 SD 7.5 10 13 50 150.8 127.4 124.8 118.3 110.5 104.0 93.6 81.9 68.9 19.5

TRS 4516 © TS 093 SD 9.3 12.5 16 185.6 156.8 153.6 145.6 136.0 128.0 115.2 100.8 84.8 25
HEAD VALUES IN METRES

TRS 4520 © TS 112 SD 11 15 20 232.0 196.0 192.0 182.0 170.0 160.0 144.0 126.0 106.0 29

TRS 4530 © TS 150 SD 15 20 30 348.0 294.0 288.0 273.0 255.0 240.0 216.0 189.0 159.0 39

TRS 4505 UH TS037 DOL 3.7 5 5 83.4 72.7 70.9 67.8 64.2 60.0 54.9 48.8 41.4 10.0

TRS 4506 UH TS045 DOL 4.5 6 6 100.1 87.2 85.1 81.3 77.0 72.0 65.9 58.5 49.6 12.0

TRS 4508 UH TS056 DOL 5.5 7.5 8 133.4 116.3 113.4 108.4 102.7 96.0 87.9 78.0 66.2 14.5

TRS 4508 UH J TS056 SD 5.5 7.5 8 65 133.4 116.3 113.4 108.4 102.7 96.0 87.9 78.0 66.2 14.5

TRS 4510 UH TS075 SD 7.5 10 10 166.8 145.3 141.8 135.5 128.4 120.0 109.9 97.5 82.7 19.5
TRS 4512 UH TS093 SD 9.3 12.5 12 200.2 174.4 170.2 162.6 154.1 144.0 131.8 117.0 99.3 25.0
TRS 4515 UH TS112 SD 11 15 15 250.2 218.0 212.7 203.3 192.6 180.0 164.8 146.3 124.1 29.0

TARO "TRS 45 SERIES" - THREE PHASE RADIAL FLOW SUBMERSIBLE PUMPSETS FOR 150 mm (6”) BOREWELLS
Approximate performance values of TRS 45 series at 220 V (-15% to +6%), 2880 rpm, 50 Hz AC power supply

CAPACITY
Motor
Pipe Size (mm)

FL Current (A)
Model Name Gpm 0.0 29.0 33.0 39.6 46.2 52.8 59.4 66.0 72.6
Connection

Rating
Stages

l/m 0.0 132 150 180 210 240 270 300 330
3
M /hr 0.0 7.9 9.0 10.8 12.6 14.4 16.2 18.0 19.8
Pump Motor kW HP
l/s 0.0 2.2 2.5 3.0 3.5 4.0 4.5 5.0 5.5
HEAD
TRS 4507 ©J SS 037 DOL 3.7 5 7 50 VALUES
IN METRES
81.2 68.6 67.2 63.7 59.5 56.0 50.4 44.1 37.1 28.0

Performance confirming to IS : 8034 and 9283 D O L - Direct On Line S D - Star Delta Maximum outer diameter : 142 mm
Note : All 6" motors are ISI marked J - HO use temporary - Star rated pumpsets © - ISI marked sets
‘UH’ series pumpsets are suitable for 6½” borewells

PRODUCT TYPE KEY

T R S 45 10 - Taro Radial flow Six inch 45 series 10 Stages T S 056 - Three phase, Six inch motor (056 - Power code)
 11
PERFORMANCE CHART
TARO "TRS 50 / 50 UH SERIES" - THREE PHASE RADIAL FLOW SUBMERSIBLE PUMPSETS FOR 150 mm (6”) BOREWELLS
Approximate performance values of TRS 50 / 50 UH series at 415 V (-15% to +6), 2880 rpm, 50 Hz AC power supply
CAPACITY
Motor

Pipe Size (mm)

FL Current (A)
Model Name Gpm 0.0 46.2 52.8 59.4 66.0 72.6 85.8 92.4 99.0
Connection

Rating

Stages
l/m 0.0 210 240 270.0 300 330.0 390.0 420 450
3
M /hr 0.0 12.6 14.4 16.2 18.0 19.8 23.4 25.2 27.0
Pump Motor kW HP
l/s 0.0 3.5 4.0 4.5 5.0 5.5 6.5 7.0 7.5

TRS 5005 © TS 037 DOL 3.7 5 5 52.5 47.0 45.0 42.8 40.0 36.3 28.8 24.3 20.0 10

TRS 5008 © TS 056 DOL 5.5 7.5 8 84.0 75.2 72.0 68.4 64.0 58.0 46.0 38.8 32.0 14.5

TRS 5010 © TS 075 SD 7.5 10 10 105.0 94.0 90.0 85.5 80.0 72.5 57.5 48.5 40.0 19.5
50
TRS 5012 © TS 093 SD 9.3 12.5 12 126.0 112.8 108.0 102.6 96.0 87.0 69.0 58.2 48.0 25

TRS 5015 © TS 112 SD 11 15 15 157.5 141.0 135.0 128.3 120.0 108.8 86.3 72.8 60.0 29
HEAD VALUES IN METRES

TRS 5020 © TS 150 SD 15 20 20 210.0 188.0 180.0 171.0 160.0 145.0 115.0 97.0 80.0 39

TRS 5004 UH TS037 DOL 3.7 5 4 68.0 57.5 54.0 51.5 48.0 44.3 35.4 30.3 24.8 10

TRS 5005 UH TS045 DOL 4.5 6 5 85.0 71.9 67.5 64.4 60.0 55.3 44.2 37.9 30.9 12

TRS 5006 UH TS056 DOL 5.5 7.5 6 102 86.3 81.0 77.3 72.0 66.4 53.0 45.5 37.1 14.5

TRS 5006 UH J TS056 SD 5.5 7.5 6 65 102 86.3 81.0 77.3 72.0 66.4 53.0 45.5 37.1 14.5

TRS 5008 UH TS075 SD 7.5 10 8 136 115 108 103 96.0 88.5 70.7 60.6 49.5 19.5

TRS 5010 UH TS093 SD 9.3 12.5 10 170 144 135 129 120 111 88.4 75.8 61.9 25

TRS 5012 UH TS112 SD 11 15 12 204 173 162 155 144 133 106 90.9 74.3 29

Performance confirming to IS : 8034 and 9283 D O L - Direct On Line S D - Star Delta Maximum outer diameter : 142 mm
Note : All 6" motors are ISI marked J - Against batch order © - ISI marked sets
‘UH’ series pumpsets are suitable for 6½” borewells

PRODUCT TYPE KEY

T R S 50 05 - Taro Radial flow Six inch 50 series 05 Stages T S 037 - Three phase, Six inch motor (037 - Power code)
T R S 50 04 UH - Taro Radial flow Six inch 50 series 04 Stages (Ultra Head) T S 037 - Three phase, Six inch motor (037 - Power code)
12
150 mm Borewell Submersibles (TRS-R)

PRODUCT FEATURES
Ÿ Available in radial flow impeller designs. Ÿ Diffusers and housings of high grade cast iron
Ÿ Dynamically balanced impellers of gunmetal (radial) and cast iron Ÿ Stainless steel stator shell to prevent rust formation.
(mixed) with SS Clads. Ÿ Specially designed carbon thrust bearing.
Ÿ Special LTB and nitrile rubber bearing bushes for high wear Ÿ High quality seal rings and sand guards to protect motor from
resistance and longer life. sand entry.
Ÿ High quality water-resistant polymer insulated wires for
Ÿ Easily rewindable Squirrel cage motor of water-cooled,designed longer life even under adverse voltage conditions.
for 280-380V (TRS-L) 50 Hz, AC power supply.
Ÿ Pressure diaphragm to compensate excess pressure due to
heating up of filled water.

MATERIAL OF CONSTRUCTION
Part Name Material Part Name Material
Impeller Gun metal Motor body AISI 304
Diffuser FG 200 Bearing housing CI - FG 200
Pump shaft AISI 410 Motor shaft AISI 410 / 55C8
Sleeve AISI 410 Journal bush LTB-4 / Carbon
Bearing bush NBR Thrust bearing SS / Carbon
Non return valve - Winding wire Polywrapped copper

APPLICATIONS
Domestic and community water supply | Water supply to high rise buildings, housing complexes, bungalows and industries | Cattle and poultry
farms | Irrigation of farms | Dairies | Cooling water circulating systems | Fire fighting systems | Fountains
 13
PERFORMANCE CHART
TARO "TRS 30 R - 40 R SERIES" - THREE PHASE RADIAL FLOW SUBMERSIBLE PUMPSETS FOR 150 mm (6”) BOREWELLS
Approximate performance values of TRS 30 R - 40 R series at 350 V (-15% to +6%), 2880 rpm, 50 Hz AC power supply
CAPACITY
Motor

Pipe Size (mm)

Gpm 0.0 9.2 13.2 19.8 26.4 30.4 33.0 35.6 39.6 46.2 52.8

FL Current (A)
Model Name
Connection

Rating

Stages
l/m 0 42 60 90.0 120 138 150.0 162 180 210 240
3
M /hr 0.0 2.5 3.6 5.4 7.2 8.3 9.0 9.7 10.8 12.6 14.4
Pump Motor kW HP
l/s 0.0 0.7 1.0 1.5 2.0 2.3 2.5 2.7 3.0 3.5 4.0

TRS 3009 RF TS 022 R DOL 2.2 3.0 9 83.6 77.5 74.3 67.5 57.7 50.3 44.5 7.0

TRS 3015 RF TS 037 R DOL 3.7 5.0 15 139 129 124 113 96.2 83.8 74.1 11.5
50
TRS 3020 RF TS 045 R DOL 4.5 6.0 20 HEAD VALUES IN METRES 186 172 165 150 128 112 98.9 13.0

TRS 3020 RF TS 056 R DOL 5.5 7.5 20 186 172 165 150 128 112 98.9 15.5

TRS 3023 R TS 056 R DOL 5.5 7.5 23 40 214 198 190 173 148 128 114 15.5

TRS 3518 R TS056 R DOL 5.5 7.5 18 175 166 161 151 137 126 118 108 92.3 60.2 15.5

TRS 4006 R TS 022 R DOL 2.2 3.0 6 55.8 52.5 50.4 47.5 45.4 43.8 42.0 38.9 32.6 26.5 7.0

TRS 4010 R © TS 037 R DOL 3.7 5.0 10 50 93.0 87.5 83.9 79.2 75.7 73.0 70.0 64.9 54.3 44.2 11.5

TRS 4012 R © TS 045 R DOL 4.5 6.0 12 112 105 101 95.0 90.8 87.6 84.0 77.8 65.1 53.0 13

TRS 4015 R TS 056 R DOL/SD 5.5 7.5 15 140 131 126 119 114 109 105 97.3 81.4 66.3 15.5

Performance confirming to IS : 8034 and 9283 DOL - Direct On Line S D - Star Delta Maximum outer diameter : 142 mm
© - ISI marked sets
PRODUCT TYPE KEY
T R S 30 15 R F - Taro Radial flow Six inch 30 series 15 Stages R - Series, Flange T S 037 R - Three phase, Six inch motor (037 - Power code) R - Series
T R S 40 15 R - Taro Radial flow Six inch 40 series 15 Stages R - Series T S 056 R - Three phase, Six inch motor (056 - Power code) R - Series
 14
PERFORMANCE CHART
TARO "TRS 43 R / 45 R SERIES" - THREE PHASE RADIAL FLOW SUBMERSIBLE PUMPSETS FOR 150 mm (6”) BOREWELLS
Approximate performance values of TRS 43 R / 45 R series at 350 V (-15% to +6%), 2880 rpm, 50 Hz AC power supply
CAPACITY
Motor

Pipe Size (mm)

Gpm 0.0 19.8 26.4 30.4 33.0 35.6 39.6 46.2 52.8 59.4 66.0 72.6

FL Current (A)
Model Name
Connection

Rating

Stages
l/m 0.0 90 120 138 150 162 180 210 240 270 300 330
3
M /hr 0.0 5.4 7.2 8.3 9.0 9.7 10.8 12.6 14.4 16.2 18.0 19.8
Pump Motor kW HP
l/s 0.0 1.5 2.0 2.3 2.5 2.7 3.0 3.5 4.0 4.5 5.0 5.5

TRS 4305 R TS 022 DOL 2.2 3 5 50.0 47.1 45.0 43.3 41.9 40.3 37.5 32.1 25.3 16.4 7

TRS 4308 R © TS 037 DOL 3.7 5 8 80.0 75.4 72.1 69.3 67.1 64.4 60.0 51.4 40.5 26.2 10.5

TRS 4310 R © TS 045 DOL 4.5 6 10 100 94.2 90.1 86.6 83.8 80.6 75.0 64.2 50.6 32.8 13
HEAD VALUES IN METRES

TRS 4312 R TS 056 DOL/SD 5.5 7.5 12 120 113 108 104 100 96.7 90.0 77.0 60.7 39.4 15.5

TRS 4313 R A TS 056 DOL 5.5 7.5 13 50 130 122 117 112 109 104 97.5 83.5 65.8 42.6 15.5

TRS 4504 R TS 022 DOL 2.2 3 4 39.0 34.8 34.0 33.5 32.9 31.9 30.0 27.5 24.7 21.4 18.4 7.0

TRS 4506 R © TS 037 DOL 3.7 5 6 58.5 52.2 51.0 50.3 49.4 47.9 45.0 41.3 37.1 32.1 27.6 11.5

TRS 4508 R ©# TS 037 DOL 3.7 5 8 78.0 69.6 68.0 67.0 65.8 63.8 60.0 55.0 49.4 42.8 36.8 13.0

TRS 4510 R © A TS 056 DOL/SD 5.5 7.5 10 97.5 87.0 85.0 83.8 82.3 79.8 75.0 68.8 61.8 53.5 46.0 15.5

Performance confirming to IS : 8034 and 9283 DOL - Direct On Line S D - Star Delta Maximum outer diameter : 142 mm
# - Pumps combined with "RL" (350V) A - Single phase also available © - ISI marked sets

PRODUCT TYPE KEY

T R S 43 10 R - Taro Radial flow Six inch 43 series 10 Stages R - Series T S 045 R - Three phase, Six inch motor (045 - Power code) R - Series
T R S 45 08 R - Taro Radial flow Six inch 45 series 08 Stages R - Series T S 037 R - Three phase, Six inch motor (037 - Power code) R - Series
 15
PERFORMANCE CHART
TARO "TRS 50 R SERIES" - THREE PHASE RADIAL FLOW SUBMERSIBLE PUMPSETS FOR 150 mm (6”) BOREWELLS
Approximate performance values of TRS 50 R series at 350 V (-15% to +6%), 2880 rpm, 50 Hz AC power supply
CAPACITY
Motor

Pipe Size (mm)

Gpm 0.0 35.6 39.2 46.2 52.8 59.4 66 79.2 92.4

FL Current (A)
Model Name
Connection

Rating

Stages
l/m 0.0 162 178 210 240 270 300 360 420
3
M /hr 0.0 9.7 10.7 12.6 14.4 16.2 18 21.6 25.2
Pump Motor kW HP
l/s 0.0 2.7 3.0 3.5 4.0 4.5 5.0 6.0 7.0

HEAD VALUES
TRS 5005 R © # TS 037 R DOL 3.7 5 5 50.0 44.7 43.7 41.9 39.85 37.5 34.83 28.43 20.4 11.5

IN METRES
TRS 5006 R # J TS 045 R DOL 4.5 6 6 50 60.0 53.6 52.5 50.3 47.82 45.0 41.796 34.116 24.4 13
TRS 5008 R A TS 056 R DOL 5.5 7.5 8 80.0 71.4 69.9 67.1 63.76 60.0 55.728 45.488 32.6 15.5

Performance confirming to IS : 8034 and 9283 DOL - Direct On Line S D - Star Delta Maximum outer diameter : 142 mm
# - Pumps combined with "RL" (350V) J - Against batch order A - Single phase also available © - ISI marked sets

PRODUCT TYPE KEY

T R S 50 05 R - Taro Radial flow Six inch 50 series 05 Stages R - Series T S 037 R - Three phase, Six inch motor (037 - Power code) R - Series
16
150 mm Stainless Steel Borewell Submersibles (TSS)

PRODUCT FEATURES
Ÿ Light weight, compact design and easy to install Ÿ Stainless steel stator shell to prevent rust formation.
Ÿ AISI 304 graded impellers and stage housings for corrosion Ÿ Specially designed carbon thrust bearing.
resistance. Ÿ High quality seal rings and sand guards to protect motor from
sand entry.
Ÿ Efficient hydraulic design with less power consumption.
Ÿ High quality water-resistant polymer insulated wires for
Ÿ Built in NRV with minimum friction. longer life even under adverse voltage conditions.
Ÿ Inside strainer construction and water lubricated rubber bushes. Ÿ Pressure diaphragm to compensate excess pressure due to
heating up of filled water.
Ÿ Easily rewindable Squirrel cage motor of water-cooled,designed
for 350 - 440 V, 50 Hz, AC power supply.

MATERIAL OF CONSTRUCTION
Part Name Material Part Name Material
Impeller AISI 304 Motor body AISI 304
Bowl AISI 304 Bearing housing CI FG 200
Pump shaft AISI 304 / 431 Motor shaft 55C8
Sleeve AISI 410 Journal bush LTB-4
Bearing bush NBR Thrust bearing AISI 420-Carbon
Non return valve AISI 304 Winding wire Polywrap insulated copper

APPLICATIONS
Irrigation (Drip / Sprinkler) | Municipal water supply | Dewatering of mine | Industrial water supply | Cooling water circulating systems | Water
treatment | Fire fighting | Aqua culture | Salt fields
 17
PERFORMANCE CHART
TARO "TSS 47 SERIES" - THREE PHASE RADIAL FLOW STAINLESS STEEL SUBMERSIBLES FOR 150 mm BOREWELLS
Approximate performance values of TSS 47 series at 415V (-15% to +6%), 2880 rpm, 50 Hz AC power supply
CAPACITY
Motor

Pipe Size (mm)

FL Current (A)
Model Name Gpm 0.0 39.6 46.2 52.8 59.4 66.0 72.6 85.8 99.0
Connection

Rating

Stages
l/m 0.0 180 210 240 270 300 330 390 450

M3/hr 0.0 10.8 12.6 14.4 16.2 18.0 19.8 23.4 27.0
Pump Motor kW HP
l/s 0.0 3.0 3.5 4.0 4.5 5.0 5.5 6.5 7.5
TSS 4703 TS 022 DOL 2.2 3 3 34.0 31.5 30.7 29.7 28.5 27.0 24.5 18.2 10.3 6.5

HEAD VALUES IN
TSS 4703 T J TS 022 DOL 2.2 3 3 34.0 31.5 30.7 29.7 28.5 27.0 24.5 18.2 10.3 6.5

METRES
TSS 4704 T J TS030 DOL 3 4 4 50 45.3 42.0 40.9 39.6 38.0 36.0 32.7 24.3 13.8
TSS 4705 TS 037 DOL 3.7 5 5 56.7 52.5 51.2 49.5 47.6 45.0 40.8 30.4 17.2 10
TSS 4705 T J TS 037 DOL 3.7 5 5 56.7 52.5 51.2 49.5 47.6 45.0 40.8 30.4 17.2 10

Performance confirming to IS : 8034 and 9283 D O L - Direct On Line S D - Star Delta Maximum outer diameter : 146 mm
Note : All 6" motors are ISI marked J - Against batch order T - Turbo set also available

PRODUCT TYPE KEY

T S S 47 05 - Taro Stainless steel(Radial flow), Six inch 47 series 05 Stages T S 037 - Three phase, Six inch motor (037 - Power code)
18
150 mm Mixed Flow Borewell Submersibles (TMS)

PRODUCT FEATURES
Ÿ Available in mixed flow impeller designs. Ÿ Built in NRV with minimum friction.
Ÿ Dynamically balanced LTB impellers with SS clads. Ÿ Stainless steel stator shell to prevent rust formation.
Ÿ Specially designed carbon thrust bearing.
Ÿ Special LTB and nitrile rubber bearing bushes for high wear
resistance and longer life. Ÿ High quality seal rings and sand guards to protect motor from
sand entry.
Ÿ Bowls of high-grade cast iron. Ÿ High quality water-resistant polymer insulated wires for
Ÿ Easily rewindable Squirrel cage motor of water-cooled,designed longer life even under adverse voltage conditions.
for 350 - 440 V, (TMS) 280-380V (TMS-L) 50 Hz, AC power Ÿ Pressure diaphragm to compensate excess pressure due to
supply. heating up of filled water.

MATERIAL OF CONSTRUCTION
Part Name Material Part Name Material
Impeller LTB-2 Motor body AISI 304
Bowl CI FG 200 A Bearing housing CI FG 200
Pump shaft AISI 410 / 431 Motor shaft 55C8 / AISI 431
Sleeve AISI 410 Journal bush LTB-4 / Carbon
Bearing bush NBR Thrust bearing SS / Carbon
Non return valve AISI 304 / NBR Winding wire Polywrapped copper

APPLICATIONS
Domestic and community water supply | Water supply to high rise buildings, housing complexes, bungalows and industries | Cattle and poultry
farms | Irrigation of farms | Dairies | Cooling water circulating systems | Fire fighting systems | Fountains
 19
PERFORMANCE CHART
TARO "TMS 55 / 60 SERIES" - THREE PHASE MIXED FLOW SUBMERSIBLE PUMPSETS FOR 150 mm (6”) BOREWELLS
Approximate performance values of TMS 55 / 60 series at 415 V (-15% to +6%), 2880 rpm, 50 Hz AC power supply
CAPACITY
Motor

Pipe Size (mm)

FL Current (A)
Model Name Gpm 0.0 46.2 52.8 66.0 85.8 106 112 125 139 152 165
Connection

Rating

Stages
l/m 0.0 210 240 300 390 480 510 570 630 690 750
3
M /hr 0.0 12.6 14.4 18.0 23.4 28.8 30.6 34.2 37.8 41.4 45.0
Pump Motor kW HP
l/s 0.0 3.5 4.0 5.0 6.5 8.0 8.5 9.0 10.5 11.5 12.5

TMS 5503 TS 022 DOL 2.2 3 3 28.5 26.4 25.8 24.6 22.5 20.0 19.1 18.0 14.0 6.5

TMS 5505 © TS 037 DOL 3.7 5 5 47.5 44.0 43.0 41.0 37.5 33.3 31.8 30.0 23.3 10.0

TMS 5508 TS 056 DOL/SD 5.5 7.5 8 76.0 70.4 68.8 65.6 60.0 53.2 50.8 48.0 37.2 14.5

TMS 5510 © TS 075 SD 7.5 10 10 65 95.0 88.0 86.0 82.0 75.0 66.5 63.5 60.0 46.5 19.5

TMS 5512 © TS 093 SD 9.3 12.5 12 114.0 105.6 103.2 98.4 90.0 79.8 76.2 72.0 55.8 25.0

TMS 5515 © TS 112 SD 11 15 15 142.5 132.0 129.0 123.0 112.5 99.8 95.3 90.0 69.8 29.0
HEAD VALUES IN METRES

TMS 5520 © TS 150 SD 15 20 20 190.0 176.0 172.0 164.0 150.0 133.0 127.0 120.0 93.0 39.0

TMS 6004 © TS 037 DOL 3.7 5 4 41.0 36.6 34.1 31.1 30.0 28.5 25.0 22.0 17.9 10

TMS 6005 © TS 045 DOL 4.5 6 5 51.3 45.8 42.6 38.9 37.5 35.6 31.3 27.5 22.4 12

TMS 6006 © TS 056 DOL/SD 5.5 7.5 6 61.5 54.9 51.2 46.7 45.0 42.8 37.5 33.0 26.9 14.5

TMS 6008 © TS 075 SD 7.5 10 8 82.0 73.2 68.2 62.2 60.0 57.0 50.0 44.0 35.8 19.5

TMS 6010 © TS 093 SD 9.3 12.5 10 65 102.5 91.5 85.3 77.8 75.0 71.3 62.5 55.0 44.8 25

TMS 6012 © TS 112 SD 11 15 12 123.0 109.8 102.3 93.3 90.0 85.5 75.0 66.0 53.7 29

TMS 6014 TS 130 SD 13 17.5 14 143.5 128.1 119.4 108.9 105.0 99.8 87.5 77.0 62.7 34

TMS 6016 TS 150 SD 15 20 16 164.0 146.4 136.4 124.4 120.0 114.0 100.0 88.0 71.6 39

TMS 6020 TS 187 SD 18.7 25 20 205.0 183.0 170.5 155.5 150.0 142.5 125.0 110.0 89.5 45

Performance confirming to IS : 8034 and 9283 D O L - Direct On Line S D - Star Delta Maximum outer diameter : 142 mm
© - ISI marked sets

PRODUCT TYPE KEY

T M S 55 05 - Taro Mixed flow Six inch 55 series 05 Stages T S 037 - Three phase, Six inch motor (037 - Power code)
T M S 60 04 - Taro Mixed flow Six inch 60 series 04 Stages T S 037 - Three phase, Six inch motor (037 - Power code)
 20
PERFORMANCE CHART
TARO "TMS 65 / 70 SERIES" - THREE PHASE MIXED FLOW SUBMERSIBLE PUMPSETS FOR 150 mm (6”) BOREWELLS
Approximate performance values of TMS 65 / 70 series at 415 V (-15% to +6%), 2880 rpm, 50 Hz AC power supply
CAPACITY
Motor

Pipe Size (mm)

FL Current (A)
Model Name Gpm 0.0 86 106 112 119 139 152 165 185 205 218 231
Connection

Rating

Stages
l/m 0.0 390 480 510 540 630 690 750 840 930 990 1050
3
M /hr 0.0 23.4 28.8 30.6 32.4 37.8 41.4 45.0 50.4 55.8 59.4 63.0
Pump Motor kW HP
l/s 0.0 6.5 8.0 8.5 9.0 10.5 11.5 12.5 14.0 15.5 16.5 17.5

TMS 6503 F TS 037 DOL 3.7 5 3 31.5 27.8 26.3 25.5 24.8 22.5 20.7 19.1 16.2 13.5 10.0

TMS 6504 F TS 045 DOL 4.5 6 4 42.0 37.1 35.1 34.0 33.1 30.0 27.6 25.5 21.6 18.0 12.0

TMS 6505 F TS 056 DOL 5.5 7.5 5 52.5 46.3 43.8 42.5 41.3 37.5 34.5 31.8 27.0 22.5 14.5

TMS 6507 TS 075 SD 7.5 10 7 73.5 64.9 61.4 59.5 57.9 52.5 48.3 44.6 37.8 31.5 19.5

TMS 6508 TS 093 SD 9.3 12.5 8 65 84.0 74.1 70.1 68.0 66.1 60.0 55.2 50.9 43.2 36.0 25.0

TMS 6510 F TS 112 SD 11 15 10 105.0 92.7 87.7 85.0 82.7 75.0 69.0 63.7 54.0 45.0 29.0

TMS 6512 TS 130 SD 13 17.5 12 126.0 111.2 105.2 102.0 99.2 90.0 82.8 76.4 64.8 54.0 34.0
HEAD VALUES IN METRES

TMS 6514 TS 150 SD 15 20 14 147.0 129.7 122.7 119.0 115.7 105.0 96.6 89.1 75.6 63.0 39.0

TMS 6517 F TS 187 SD 18.7 25 17 178.5 157.5 149.0 144.5 140.5 127.5 117.3 108.2 91.8 76.5 45.0

TMS 7004 TS 056 DOL 5.5 7.5 4 43.0 35.0 34.4 33.8 31.6 30.0 28.2 25.0 21.4 18.6 16.0 14.5

TMS 7004 TS 056 SD 5.5 7.5 4 43.0 35.0 34.4 33.8 31.6 30.0 28.2 25.0 21.4 18.6 16.0 14.5

TMS 7005 © TS 075 SD 7.5 10 5 53.8 43.8 43.0 42.3 39.5 37.5 35.3 31.3 26.8 23.3 20.0 19.5

TMS 7006 © TS 093 SD 9.3 12.5 6 64.5 52.5 51.6 50.7 47.4 45.0 42.3 37.5 32.1 27.9 24.0 25.0
75
TMS 7008 TS 112 SD 11 15 8 86.0 70.0 68.8 67.6 63.2 60.0 56.4 50.0 42.8 37.2 32.0 29.0

TMS 7010 TS 150 SD 15 20 10 107.5 87.5 86.0 84.5 79.0 75.0 70.5 62.5 53.5 46.5 40.0 39.0

TMS 7013 TS 187 SD 18.7 25 13 139.8 113.8 111.8 109.9 102.7 97.5 91.7 81.3 69.6 60.5 52.0 45.0

TMS 7016 TS 225 SD 22.5 30 16 172.0 140.0 137.6 135.2 126.4 120.0 112.8 100.0 85.6 74.4 64.0 52.0

Performance confirming to IS : 8034 and 9283 D O L - Direct On Line S D - Star Delta Maximum outer diameter : 142 mm
Note : All 6" motors are ISI marked © - ISI marked sets - Star rated pumpsets
‘F’ series is also available in 75 mm delivery

PRODUCT TYPE KEY

T M S 65 03 - Taro Mixed flow Six inch 65 series 03 Stages T S 037 - Three phase, Six inch motor (037 - Power code)
T M S 70 04 - Taro Mixed flow Six inch 70 series 04 Stages T S 056 - Three phase, Six inch motor (056 - Power code)
 21
PERFORMANCE CHART
TARO "TMS 75 / 100 SERIES" - THREE PHASE MIXED FLOW SUBMERSIBLE PUMPSETS FOR 150 mm (6”) BOREWELLS
Approximate performance values of TMS 75 / 100 series at 415 V (-15% to +6%), 2880 rpm, 50 Hz AC power supply
CAPACITY
Motor

Pipe Size (mm)

Model Name Gpm 0.0 112 119 139 152 165 185 205 218 231 244 257 271 284 297 317 356 396

FL Current (A)
Connection

Rating Stages
l/m 0.0 510 540 630 690 750 840 930 990 1050 1110 1170 1230 1290 1350 1440 1620 1800
3
M /hr 0.0 30.6 32.4 37.8 41.4 45.0 50.4 55.8 59.4 63.0 66.6 70 73.8 77.4 81.0 86.4 97.2 108
Pump Motor kW HP
l/s 0.0 8.5 9.0 10.5 11.5 12.5 14.0 15.5 16.5 17.5 18.5 20 20.5 21.5 22.5 24.0 27.0 30.0

TMS 7505 TS 093 SD 9.3 12.5 5 55.0 44.3 43.5 41.3 39.5 37.5 34.5 31.0 28.3 25.5 22.5 19.5 25.0
75
TMS 7506 TS 112 SD 11 15 6 66.0 53.1 52.2 49.5 47.4 45.0 41.4 37.2 33.9 30.6 27.0 23.4 29.0
HEAD VALUES IN METRES

TMS 10004 D w TS 056 DOL 5.5 7.5 4 44.0 36.4 35.6 34.2 32.8 31.7 30.6 29.4 28.2 26.9 25.6 24.1 21.7 16.6 11.3 17.2

TMS 10005 D w TS 075 SD 7.5 10 5 55.0 45.5 44.5 42.8 41.0 39.6 38.2 36.8 35.2 33.7 32.0 30.1 27.2 20.7 14.2 22.5

TMS 10006 D w TS 112 SD 11 15 6 100 66.0 54.5 53.3 51.3 49.1 47.5 45.8 44.1 42.2 40.4 38.3 36.1 32.6 24.8 17.0 29.0

TMS 10007 D w TS 130 SD 13 17.5 7 77.0 63.6 62.2 59.9 57.3 55.4 53.5 51.5 49.3 47.1 44.7 42.1 38.0 29.0 19.8 34.0

TMS 10008 D w TS 150 SD 15 20 8 88.0 72.7 71.1 68.4 65.5 63.4 61.1 58.8 56.3 53.8 51.1 48.2 43.4 33.1 22.6 39.0

Performance confirming to IS : 8034 and 9283 D O L - Direct On Line S D - Star Delta Maximum outer diameter : 142 mm
Note : All 6" motors are ISI marked w - R series only available

PRODUCT TYPE KEY

T M S 75 05 - Taro Mixed flow Six inch 75 series 05 Stages T S 093 - Three phase, Six inch motor (093 - Power code)
T M S 100 03 - Taro Mixed flow Six inch 100 series 03 Stages T S 056 - Three phase, Six inch motor (056 - Power code)
 22
PERFORMANCE CHART
TARO "TMS 55 R / 60 R SERIES" - THREE PHASE MIXED FLOW SUBMERSIBLE PUMPSETS FOR 150 mm (6”) BOREWELLS
Approximate performance values of TMS 55 R / 60 R series at 415 V (-15% to +6%), 2880 rpm, 50 Hz AC power supply
CAPACITY
Motor

Pipe Size (mm)

Model Name Gpm 0.0 39.6 52.8 66.0 79.2 92.4 99.0 105.6 118.8 132.0 145.2 158.4

FL Current (A)
Connection

Rating Stages
l/m 0.0 180.0 240.0 300.0 360.0 420.0 450.0 480.0 540.0 600.0 660.0 720.0
3
M /hr 0.0 10.8 14.4 18.0 21.6 25.2 27.0 28.8 32.4 36.0 39.6 43.2
Pump Motor kW HP
l/s 0.0 3.0 4.0 5.0 6.0 7.0 7.5 8.0 9.0 10.0 11.0 12.0

TMS 5505 R ± TS 037 R DOL 3.7 5 5 49.0 42.7 40.4 37.9 35.0 31.6 29.7 27.7 23.3 18.3 11.5

TMS 5506 R ± TS 045 R DOL 4.5 6 6 65 58.8 51.2 48.5 45.5 42.0 37.9 35.6 33.2 28.0 22.0 13.0
HEAD VALUES IN METRES

TMS 5508 R ± TS 056 R DOL/SD 5.5 7.5 8 78.4 68.3 64.6 60.6 56.0 50.6 47.5 44.3 37.3 29.3 15.5

TMS 6004 R ±@ TS 037 R DOL 3.7 5 4 40.0 35.0 33.3 31.3 29.2 28.0 26.7 23.9 20.6 16.9 12.9 11.5

TMS 6005 R ± TS 045 R DOL 4.5 6 5 50.0 43.8 41.6 39.1 36.5 35.0 33.4 29.9 25.8 21.1 16.1 13.0

TMS 6006 R ± TS 056 R DOL 5.5 7.5 6 65 60.0 52.5 50.0 47.0 43.8 42.0 40.1 35.9 30.9 25.4 19.4 15.5

TMS 6006 R ±J TS 056 R SD 5.5 7.5 6 60.0 52.5 50.0 47.0 43.8 42.0 40.1 35.9 30.9 25.4 19.4 15.5

TMS 6008 R ±A TS 056 R SD 5.5 7.5 8 80.0 70.0 66.6 62.6 58.4 56.0 53.4 47.8 41.2 33.8 25.8 21.5

Performance confirming to IS : 8034 and 9283 D O L - Direct On Line S D - Star Delta Maximum outer diameter : 142 mm
@ - 'F series' is also available in 75 mm delivery J - Against batch order A - Single phase also available ± - SI Impeller also available
Note : All 6" motors are ISI marked

PRODUCT TYPE KEY

T M S 55 05 R - Taro Mixed flow Six inch 55 series 05 Stages, R - series T S 037 R - Three phase, Six inch motor (037 - Power code), R - series
T M S 60 06 R - Taro Mixed flow Six inch 60 series 06 Stages, R - series T S 056 R - Three phase, Six inch motor (056 - Power code), R - series
MTP Road, G.N.Mills Post, Coimbatore - 641 029.
E-mail : [email protected] | Website : www.texmo.com © 2013